Zebra DS8108 Snelstartgids

Categorie
Streepjescodelezers
Type
Snelstartgids
Digital Scanner
Quick Start Guide
MN-002927-02EN
DS8108
2 DS8108 Digital Scanner Quick Start Guide
No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means,
without permission in writing from Zebra. This includes electronic or mechanical means, such as photocopying,
recording, or information storage and retrieval systems. The material in this manual is subject to change without
notice.
Zebra reserves the right to make changes to any product to improve reliability, function, or design.
Zebra does not assume any product liability arising out of, or in connection with, the application or use of any
product, circuit, or application described herein.
No license is granted, either expressly or by implication estoppel, or otherwise under any patent right or patent,
covering or relating to any combination, system, apparatus, machine, material, method, or process in which Zebra
products might be used.
An implied license exists only for equipment, circuits, and subsystems contained in Zebra products.
Warranty
For the complete Zebra hardware product warranty statement, go to: http://www.zebra.com/warranty.
For Australia Only
For Australia Only. This warranty is given by Zebra Technologies Asia Pacific Pte. Ltd., 71 Robinson Road,
#05-02/03, Singapore 068895, Singapore. Our goods come with guarantees that cannot be excluded under the
Australia Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any
other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the
goods fail to be of acceptable quality and the failure does not amount to a major failure.
Zebra Technologies Corporation Australia’s limited warranty above is in addition to any rights and remedies you
may have under the Australian Consumer Law. If you have any queries, please call Zebra Technologies
Corporation at +65 6858 0722. You may also visit our website: http://www.zebra.com
for the most updated
warranty terms.
Service Information
If you have a problem using the equipment, contact your facility’s Technical or Systems Support. If there is a
problem with the equipment, they will contact the Zebra Global Customer Support Center at:
http://www.zebra.com/support
.
For the latest version of this guide go to:
http://www.zebra.com/support.
DS8108 Digital Scanner Quick Start Guide 3
Scanner Features and Presentation Mode
Aiming - Right/Wrong
Scanning
LED Indicator
Scan Window
Scan Trigger
012345
012345
Hand-Held Hands-Free
(Presentation)
4 DS8108 Digital Scanner Quick Start Guide
Connect Host Interface
USB
Scan ONE of the bar codes below. The digital scanner automatically detects the host interface type and uses the
default setting. If the default (*) does not meet your requirements, scan another host bar code below.
NOTE Cables may vary depending on configuration.
*
USB Keyboard HID
IBM Hand-Held USB
IBM OPOS
(IBM Hand-Held USB with Full Scan Disable)
Symbol Native API (SNAPI) with Imaging Interface
DS8108 Digital Scanner Quick Start Guide 5
RS-232
Scan ONE of the bar codes below. The digital scanner automatically detects the host interface type and uses the
default setting. If the default (*) does not meet your requirements, scan another host bar code below.
*Standard RS-232
ICL RS-232
Nixdorf RS-232 Mode A
Nixdorf RS-232 Mode B
OPOS/JPOS
Fujitsu RS-232
6 DS8108 Digital Scanner Quick Start Guide
Keyboard Wedge
Scan ONE of the bar codes below. The digital scanner automatically detects the host interface type and uses the
default setting. If the default (*) does not meet your requirements, scan the IBM PC/AT and IBM PC COMPATIBLE
bar code below.
*IBM AT Notebook
IBM PC/AT & IBM PC Compatibles
DS8108 Digital Scanner Quick Start Guide 7
IBM 46XX
Scan ONE of the bar codes below. The digital scanner automatically detects the host interface type, but there is
no default setting. Scan one of the bar codes below to select the appropriate port.
Non-IBM Scanner Emulation (Port 5B)
Hand-Held Scanner Emulation (Port 9B)
Table-Top Scanner Emulation (Port 17)
8 DS8108 Digital Scanner Quick Start Guide
Useful Bar Codes
Set Defaults
Return to Factory Defaults
Add a Tab Key
To add a Tab key after scanned data, scan the bar code below.
Add a Tab Key
Add an Enter Key
To add an Enter key after scanned data, scan the bar code below.
Add Enter Key (Carriage Return/Line Feed)
USB Caps Lock Override
USB-Override Caps Lock Key
(Enable)
*USB-Do Not Override Caps Lock Key
(Disable)
DS8108 Digital Scanner Quick Start Guide 9
User Indications (By Default)
123Scan
123Scan is an easy-to-use, PC-based software tool that enables rapid and easy customized setup of a scanner via
a bar code or USB cable. For more information, visit: http://www.zebra.com/123Scan
.
Utility Functionality
Device configuration
Electronic programming (USB cable)
Programming bar code(s)
Data view - scan log (display scanned bar code data)
Access asset tracking information
Upgrade firmware and view release notes
Remote management (SMS package generation).
Indication Beeper Sequence
Power up Low/medium/high beeps
Bar code decoded Medium beep
Transmission error detected; data is ignored 4 long low beeps
Successful parameter setting High/low/high/low beeps
Correct programming sequence performed High/low beeps
Incorrect programming sequence, or Cancel bar code
scanned
Long low/long high beeps
Indication LED Indicator
Hand-Held Scanning
Digital scanner is on and ready to scan, or no power
to scanner
Off
Bar code is successfully decoded Green flash
Transmission error Red
Hands-Free (Presentation) Scanning
No power to scanner Off
Digital scanner is ready to scan Green
Bar code is successfully decoded Off momentarily
Transmission error Red
10 DS8108 Digital Scanner Quick Start Guide
Troubleshooting
Digital scanner not working
No power to scanner Connect scanner to powered host, or connect power supply.
Digital scanner disabled Ensure that correct host interface cable is used.
Digital scanner decoding bar code, but data not transmitting to host
Host interface not configured properly Scan appropriate host parameter bar codes.
Interface cable is loose Ensure all cable connections are secure.
Invalid ADF rule Program the correct ADF rules.
Digital scanner not decoding bar code
Digital scanner not programmed for bar code
type
Ensure scanner is programmed to read type of bar code being
scanned.
Bar code is unreadable Ensure the bar code is not defaced; try scanning a test bar code of the
same bar code type.
Distance between scanner and bar code
incorrect
Move scanner closer to, or further from bar code.
Scanned data incorrectly displayed on host
Host interface not configured properly Scan appropriate host parameter bar codes.
Region improperly configured Select appropriate country and language encoding scheme.
DS8108 Digital Scanner Quick Start Guide 11
RECOMMENDED USAGE GUIDE - OPTIMUM BODY POSTURE
AVOID REACHING
AVOID BENDING
AVOID EXTREME
WRIST ANGLES
12 DS8108 Digital Scanner Quick Start Guide
Regulatory Information
This device is approved under Zebra Technologies Corporation.
This guide applies to Model Number DS8108.
All Zebra devices are designed to be compliant with the rules and regulations in the locations they are sold and will
be labeled as required.
Local language translations are available at the following website: www.zebra.com/support
.
Any changes or modifications to Zebra equipment not expressly approved by Zebra could void the user's authority
to operate the equipment.
Health and Safety Recommendations
Ergonomic Recommendations
Caution: In order to avoid or minimize the potential risk of ergonomic injury follow the recommendations below.
Consult with your local Health & Safety Manager to ensure that you are adhering to your company's safety
programs to prevent employee injury.
Reduce or eliminate repetitive motion
Maintain a natural position
Reduce or eliminate excessive force
Keep objects that are used frequently within easy reach
Perform tasks at correct heights
Reduce or eliminate vibration
Reduce or eliminate direct pressure
Provide adjustable workstations
Provide adequate clearance
Provide a suitable working environment
Improve work procedures.
LED Devices
Classified as 'EXEMPT RISK GROUP' according to IEC 62471:2006 and EN 62471:2008. Pulse duration: 9 ms.
Power Supply
Use ONLY a Zebra approved UL LISTED ITE (IEC/EN 60950-1, LPS/SELV) power supply with electrical ratings:
Output 5.2Vdc, min 1.1A, with a maximum ambient temperature of at least 50 degrees C. Use of alternative power
supply will invalidate any approvals given to this unit and may be dangerous.
DS8108 Digital Scanner Quick Start Guide 13
Radio Frequency Interference Requirements - FCC
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
Consult the dealer or an experienced radio/TV technician for help.
Radio Frequency Interference Requirements-Canada
CAN ICES-3 (B)/NMB-3(B).
Statement of Compliance
Zebra hereby declares that this device is in compliance with all applicable Directives, 2014/30/EU, 2014/35/EU and
2011/65/EU.
The full text of the EU Declaration of Conformity is available at the following Internet address:
http://www.zebra.com/doc
.
Other Countries
Japan (VCCI) - Voluntary Control Council for Interference
Class B ITE
Korea Warning Statement for Class B ITE
Marking and European Economic Area (EEA)
B
( )
(B )
,
.
14 DS8108 Digital Scanner Quick Start Guide
Chile
Este equipo cumple con la Resolución No 403 de 2008, de la Subsecretaria de telecomunicaciones, relativa a
radiaciones electromagnéticas.
China
www.zebra.com/support
Ukraine
Thailand


 .
Eurasian Customs Union
Евразийский Таможенный Союз
Данный продукт соответствует требованиям знака EAC.
TURKISH WEEE Statement of Compliance
EEE Yönetmeliğine Uygundur
忂彯孧斖ẍᶳ仹⛨⎗ᶳ弥⻻⛘宕妨㓗㊩䘬ṏ⑩宜㖶Ḏ
DS8108 Digital Scanner Quick Start Guide 15
China RoHS
This table was created to comply with China RoHS requirements.
Waste Electrical and Electronic Equipment (WEEE)
English: For EU Customers: All products at the end of their life must be returned to Zebra for recycling. For information on how
to return product, please go to: http://www.zebra.com/weee.
Français: Clients de l'Union Européenne: Tous les produits en fin de cycle de vie doivent être retournés à Zebra pour
recyclage. Pour de plus amples informations sur le retour de produits, consultez : http://www.zebra.com/weee.
Español: Para clientes en la Unión Europea: todos los productos deberán entregarse a Zebra al final de su ciclo de vida para
que sean reciclados. Si desea más información sobre cómo devolver un producto, visite: http://www.zebra.com/weee.
Български: За клиенти от ЕС: След края на полезния им живот всички продукти трябва да се връщат на Zebra за
рециклиране. За информация относно връщането на продукти, моля отидете на адрес: http://www.zebra.com/weee.
Deutsch: Für Kunden innerhalb der EU: Alle Produkte müssen am Ende ihrer Lebensdauer zum Recycling an Zebra
zurückgesandt werden. Informationen zur Rücksendung von Produkten finden Sie unter http://www.zebra.com/weee.
Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del rispettivo ciclo di vita devono essere restituiti a Zebra
al fine di consentirne il riciclaggio. Per informazioni sulle modalità di restituzione, visitare il seguente sito Web:
http://www.zebra.com/weee.
Português: Para clientes da UE: todos os produtos no fim de vida devem ser devolvidos à Zebra para reciclagem. Para obter
informações sobre como devolver o produto, visite: http://www.zebra.com/weee.
Nederlands: Voor klanten in de EU: alle producten dienen aan het einde van hun levensduur naar Zebra te worden
teruggezonden voor recycling. Raadpleeg http://www.zebra.com/weee voor meer informatie over het terugzenden van
producten.
Polski: Klienci z obszaru Unii Europejskiej: Produkty wycofane z eksploatacji naleźy zwrócić do firmy Zebra w celu ich
utylizacji. Informacje na temat zwrotu produktów znajdują się na stronie internetowej http://www.zebra.com/weee.
MN-002927-02EN Revision A - March 2018
Zebra Technologies Corporation, Inc.
3 Overlook Point
Lincolnshire, IL 60069, U.S.A.
http://www.zebra.com
Zebra and the stylized Zebra head are trademarks of ZIH Corp., registered in many
jurisdictions worldwide. All other trademarks are the property of their respective owners.
© 2018 Symbol Technologies LLC, a subsidiary of Zebra Technologies Corporation. All
Rights Reserved.
Čeština: Pro zákazníky z EU: Všechny produkty je nutné po skonèení jejich životnosti vrátit spoleènosti Zebra k recyklaci.
Informace o zpùsobu vrácení produktu najdete na webové stránce: http://www.zebra.com/weee.
Eesti: EL klientidele: kõik tooted tuleb nende eluea lõppedes tagastada taaskasutamise eesmärgil Zebra'ile. Lisainformatsiooni
saamiseks toote tagastamise kohta külastage palun aadressi: http://www.zebra.com/weee.
Magyar: Az EU-ban vásárlóknak: Minden tönkrement terméket a Zebra vállalathoz kell eljuttatni újrahasznosítás céljából. A
termék visszajuttatásának módjával kapcsolatos tudnivalókért látogasson el a http://www.zebra.com/weee weboldalra.
Svenska: För kunder inom EU: Alla produkter som uppnått sin livslängd måste returneras till Zebra för återvinning. Information
om hur du returnerar produkten finns på http://www.zebra.com/weee.
Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on palautettava kierrätettäväksi Zebra-yhtiöön, kun tuotetta ei
enää käytetä. Lisätietoja tuotteen palauttamisesta on osoitteessa http://www.zebra.com/weee.
Dansk: Til kunder i EU: Alle produkter skal returneres til Zebra til recirkulering, når de er udtjent. Læs oplysningerne om
returnering af produkter på: http://www.zebra.com/weee.
Ελληνικά: Για πελάτες στην Ε.Ε.: Όλα τα προϊόντα, στο τέλος της διάρκειας ζωής τους, πρέπει να επιστρέφονται στην Zebra για
ανακύκλωση. Για περισσότερες πληροφορίες σχετικά με την επιστροφή ενός προϊόντος, επισκεφθείτε τη διεύθυνση
http://www.zebra.com/weee στο ∆ιαδίκτυο
.
Malti: Għal klijenti fl-UE: il-prodotti kollha li jkunu waslu fl-aħħar tal-ħajja ta' l-użu tagħhom, iridu jiġu rritornati għand Zebra
għar-riċiklaġġ. Għal aktar tagħrif dwar kif għandek tirritorna l-prodott, jekk jogħġbok żur: http://www.zebra.com/weee.
Românesc: Pentru clienţii din UE: Toate produsele, la sfârşitul duratei lor de funcţionare, trebuie returnate la Zebra pentru
reciclare. Pentru informaţii despre returnarea produsului, accesaţi: http://www.zebra.com/weee.
Slovenski: Za kupce v EU: vsi izdelki se morajo po poteku življenjske dobe vrniti podjetju Zebra za reciklažo. Za informacije o
vračilu izdelka obiščite: http://www.zebra.com/weee.
Slovenčina: Pre zákazníkov z krajín EU: Všetky výrobky musia byť po uplynutí doby ich životnosti vrátené spoločnosti Zebra
na recykláciu. Bližšie informácie o vrátení výrobkov nájdete na: http://www.zebra.com/weee.
Lietuvių: ES vartotojams: visi gaminiai, pasibaigus jų eksploatacijos laikui, turi būti grąžinti utilizuoti į kompaniją „Zebra“.
Daugiau informacijos, kaip grąžinti gaminį, rasite: http://www.zebra.com/weee.
Latviešu: ES klientiem: visi produkti pēc to kalpošanas mūža beigām ir jānogādā atpakaļ Zebra otrreiz
ējai pārstrādei. Lai iegūtu
informāciju par produktu nogādāšanu Zebra, lūdzu, skatiet: http://www.zebra.com/weee.
Türkçe: AB Müşterileri için: Kullanım süresi dolan tüm ürünler geri dönüştürme için Zebra'ya iade edilmelidir. Ürünlerin nasıl
iade edileceği hakkında bilgi için lütfen şu adresi ziyaret edin: http://www.zebra.com/weee.
Hrvatski: Za kupce u Europskoj uniji: Svi se proizvodi po isteku vijeka trajanja moraju vratiti tvrtki Zebra na recikliranje.
Informacije o načinu vraćanja proizvoda potražite na web-stranici: http://www.zebra.com/weee.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Zebra DS8108 Snelstartgids

Categorie
Streepjescodelezers
Type
Snelstartgids