Yamaha CVP-805 Handleiding

Merk: Yamaha

Model: CVP-805

Categorie: Synthesizer

Type: Handleiding

Deze handleiding is ook geschikt voor

CVP-809

CVP

809

CVP

805

Reference Manual

This manual explains the functions called up by touching each icon shown in the Menu display.

Please read the Owner’s Manual first for basic operations, before reading this Reference Manual.

• The illustrations and displays as shown in this manual are based on the CVP-809 (in English). These are for instructional purposes

only, and may appear somewhat different from those on your instrument.

• The explanations in this manual apply to the firmware version 1.00. Yamaha may from time to time update firmware of the product

without notice for improvement. We recommend that you check our website for later releases and upgrade your firmware.

https://download.yamaha.com/

• The company names and product names in this manual are the trademarks or registered trademarks of their respective companies.

Using the PDF manual

• To quickly jump to items and topics of interest, click on the desired items in the “Bookmarks” index to the left of

the computer display window. (Click the “Bookmarks” tab to open the index if it is not displayed.)

• Click the page numbers that appear in this manual to go directly to the corresponding page.

• Select “Find” or “Advanced Search” from the Adobe Reader “Edit” menu and enter a keyword to locate related

information anywhere in the document.

NOTE The names and positions of menu items may vary according to the version of Adobe Reader being used.

CVP-809/CVP-805 Reference Manual 2

Contents

Each chapter in this Reference Manual corresponds to each icons on the Menu display.

Adjusting the Tempo............................. 4

Transposing the Pitch in Semitones ..... 5

Changing the Split Point, Fingering Type

or Chord Detection Area ....................... 6

Learning How To Play Specific Chords

(Chord Tutor)........................................ 8

Adjusting the Volume Balance.............. 9

Editing the Volume and Tonal Balance

(Mixer) ................................................. 10

Editing Music Notation (Score) Settings

.............................................................. 18

Editing Lyrics Display Settings ........... 20

Showing the Text Display and Editing

Text Display Settings........................... 22

Using Keyboard Harmony................... 24

Microphone Settings............................ 26

Vocal Harmony Settings...................... 28

Using Playlist ....................................... 33

Calling Up Registration Memory

Numbers in Order

(Registration Sequence)....................... 35

Disabling Recall of Specific Items

(Registration Freeze) ........................... 37

Playing Styles Automatically with Your

Custom Chord Progressions

(Chord Looper).................................... 38

Assigning a Specific Function to Each

Pedal or ASSIGNABLE button ............43

Editing a Voice (Voice Edit).................47

Editing an Organ Flutes Voice

(Voice Edit)...........................................51

Creating/Editing Styles (Style Creator)53

Creating/Editing MIDI Songs

(Song Creator)......................................66

Voice Settings .......................................78

Style Playback Related Settings............84

Song Settings Related to Playback/

Recording .............................................87

Fine Tuning the Pitch...........................92

Setting the Touch Sensitivity of the

Keyboard ..............................................94

Metronome Settings.............................95

MIDI Settings .......................................96

Making Global Settings (Utility) .......102

Connecting to a Bluetooth-equipped

Device .................................................107

Wireless LAN Settings........................108

Making the Time Settings ..................110

Index.......................................................... 111

NOTE The “Bluetooth” icon is shown only if the instrument is equipped with Bluetooth functionality. Depending on the country in which

you purchased it, Bluetooth may not be available.

NOTE The “WirelessLAN” and “Time” icons are shown only when the USB Wireless LAN adaptor (UD-WL01) is connected to the [USB

TO DEVICE] terminal.

CVP-809/CVP-805 Reference Manual 3

Calling up Desired Functions from the Home Display

From all the functions shown on the Menu display, you can pick out an often used one and register it to a shortcut

and place it in the Menu area at the bottom of the Home display. Although seven shortcuts are registered by default,

you can customize them as necessary.

1 Touch and hold the icon of the desired function until the color of the shortcut area

(bottom of the display) changes.

NOTE To cancel this operation, touch any blank location on the display before going on to step 2.

2 From the seven locations at the bottom of the display, touch the one you want to replace.

The function selected in step 1 will be registered, replacing the one selected here.

To delete or move a shortcut, touch and hold the desired shortcut icon on the Home display or the Menu display until

the color changes. Then, touch the same icon again to delete it or touch the desired destination icon to move the

shortcut.

CVP-809/CVP-805 Reference Manual 4

Adjusting the Tempo

NOTE The tempo value of an Audio Song is set via the Time Stretch function. Refer to the Owner’s Manual, Chapter 5.

Indicates the tempo value during playback of the metronome, Style and MIDI Song.

Indicates the tempo value of the current Style. The Style will be started at this tempo.

Indicates the tempo value of the current MIDI Song. The Song will be started at this tempo.

These are basically equivalent to the TEMPO [-]/[+] buttons on the panel. If you want to call up the default

tempo of the current Style and MIDI Song, touch and hold any area in – .

Equivalent to the [TAP TEMPO] button on the panel.

CVP-809/CVP-805 Reference Manual 5

Transposing the Pitch in Semitones

You can transpose the overall pitch of the instrument (the keyboard sound, Style playback, MIDI Song playback, and so

on) in semitone steps.

NOTE The pitch of an Audio Song is adjusted via the Pitch Shift function. Refer to the Owner’s Manual, Chapter 5.

NOTE Transpose is not applied to the Drum Kits and SFX Kits Voice.

NOTE Transpose can also be done by using the TRANSPOSE buttons on the control panel. By touching the Transpose pop-up several

times, you can select the part to be transpose as desired.

Master

Transposes the overall pitch of the instrument, except for the Audio Songs, sound input to the [MIC/

LINE IN] jack, and the Audio input from an external device by using such as [AUX IN] jack.

Keyboard

Transposes the pitch of keyboard including Style playback (controlled via the chord section of the

keyboard).

Song

Transposes only the pitch of MIDI Song playback.

CVP-809/CVP-805 Reference Manual 6

Changing the Split Point, Fingering Type

or Chord Detection Area

For information about Split Point, refer to the Owner’s Manual, Chapter 3. For information about Fingering Types, refer

to the Owner’s Manual, Chapter 4.

Chord Types Recognized in the Fingered Mode

Split Point/Fingering Type

Chord Name [Abbreviation] Normal Voicing Display for root “C”

1+8 1+8 C1+8

1+5 1+5 C1+5

Major [M] 1+3+5 C

Sixth [6] 1+(3)+5+6 C6

Major seventh [M7] 1+3+(5)+7 CM7

Major seventh flatted fifth [M7

♭

5] 1+3+

♭

5+7 CM7(

♭

Major seventh add sharp eleventh [M7(

♯

11)] 1+(2)+3+

♯

4+5+7 CM7(

♯

11)

Add ninth [(add9)] 1+2+3+5 Cadd9

Major seventh ninth [M7_9] 1+2+3+(5)+7 CM7(9)

Sixth ninth [6_9] 1+2+3+(5)+6 C6(9)

Flatted fifth [(

♭

5)] 1+3+

♭

Changing the Split Point, Fingering Type or Chord Detection Area

CVP-809/CVP-805 Reference Manual

NOTE Notes in parentheses can be omitted.

NOTE The “cancel” indication refers to Chord Cancel, which stops the last selected chord from playing and leaves only the drums/

rhythm.

By changing the Chord Detection area from the left-hand section to the right-hand section, you can play a bass line with

your left hand while using your right hand to play chords for controlling Style playback.

1 Call up page 2/2 of the Split Point/Fingering window.

2 Make the necessary settings by touching the display.

Augmented [aug] 1+3+

♯

5Caug

Seventh augmented [7aug] 1+3+

♯

♭

7 C7aug

Major seventh augmented [M7aug] 1+(3)+

♯

5+7 CM7aug

Minor [m] 1+

♭

3+5 Cm

Minor sixth [m6] 1+

♭

3+5+6 Cm6

Minor seventh [m7] 1+

♭

3+(5)+

♭

7Cm7

Minor seventh flatted fifth [m7

♭

5] 1+

♭

7Cm7(

♭

Minor add ninth [m(add9)] 1+2+

♭

3+5 Cm add9

Minor seventh ninth [m7(9)] 1+2+

♭

3+(5)+

♭

7 Cm7(9)

Minor seventh eleventh [m7(11)] 1+(2)+

♭

3+4+5+(

♭

7) Cm7(11)

Minor major seventh flatted fifth [mM7

♭

5] 1+

♭

5+7 CmM7(

♭

Minor major seventh [mM7] 1+

♭

3+(5)+7 CmM7

Minor major seventh ninth [mM7(9)] 1+2+

♭

3+(5)+7 CmM7(9)

Diminished [dim] 1+

♭

5Cdim

Diminished seventh [dim7] 1+

♭

5+6 Cdim7

Seventh [7] 1+3+(5)+

♭

7C7

Seventh suspended fourth [7sus4] 1+4+5+

♭

7C7sus4

Seventh ninth [7(9)] 1+2+3+(5)+

♭

7 C7(9)

Seventh add sharp eleventh [7(

♯

11)] 1+(2)+3+

♯

4+5+

♭

7C7(

♯

11)

Seventh add thirteenth [7(13)] 1+3+(5)+6+

♭

7 C7(13)

Seventh flatted fifth [7

♭

5] 1+3+

♭

7C7(

♭

Seventh flatted ninth [7(

♭

9)] 1+

♭

2+3+(5)+

♭

7C7(

♭

Seventh add flatted thirteenth [7(

♭

13)] 1+3+5+

♭

7C7(

♭

13)

Seventh sharp ninth [7(

♯

9)] 1+

♯

2+3+(5)+

♭

7C7(

♯

Suspended fourth [sus4] 1+4+5 Csus4

One plus two plus five [sus2] 1+2+5 Csus2

cancel 1+

♭

2+2 Cancel

Specifying Chords with Your Right Hand for Style Playback

Chord Detection Area

Select “Upper.” The Chord section is set to the right of the Left Split Point.

Fingering type is set to “Fingered*” automatically.

NOTE “Fingered*” is basically same as “Fingered,” except that “1+5,” “1+8” and Chord

Cancel are not available.

NOTE When the Chord Detection Area is set to “Lower,” the Chord section is set to the left

of the Style Split Point. For details, refer to the Owner’s Manual, Chapter 4.

Manual Bass

When this is set to “On,” the bass part of the current Style is muted and the Voice of

left part is assigned.

NOTE This parameter is available only when the “Chord Detection Area” is set to “Upper.”

Chord Name [Abbreviation] Normal Voicing Display for root “C”

Style Split Point

Chord Detection Area

(Upper)

Left Split Point

Left Part

Main/Layer parts

CVP-809/CVP-805 Reference Manual 8

Learning How To Play Specific Chords

(Chord Tutor)

If you know the name of a chord but don’t know how to play it, this function indicates you the notes you should press.

NOTE Depending on the chord, some notes may be omitted.

Root

Lets you select the desired Chord Root.

Type

Lets you select the desired Chord Type.

CVP-809/CVP-805 Reference Manual 9

Adjusting the Volume Balance

For information about this display, refer to the Owner’s Manual, Chapter 1.

CVP-809/CVP-805 Reference Manual 10

Editing the Volume and Tonal Balance

(Mixer)

The “Panel” – “Audio” Part Selection tabs at the top of the Mixer display let you adjust the sound for each corresponding

part, while “Master” lets you make overall sound adjustments for the entire instrument.

NOTE When an Audio Song is selected, you cannot set the parameters related to the Song part or channels.

NOTE Knobs and sliders appear on the setting displays only when the relevant parameters are available.

For a visual indication of the signal flow and configuration of the Mixer, refer to the Block Diagram on page 17.

This function modifies the tonal characteristics (brightness, etc.) of the sound by cutting the output of a specific

frequency portion of the sound. This is not available when you select “Master” from among the tabs at the top of the

Mixer display.

Filter

Harmonic Content

Allows you to adjust the Resonance effect (page 49) for each part. This can be used in

combination with the “Brightness” parameter to add further character to the sound.

Brightness

Determines the brightness of the sound for each part by adjusting the cutoff frequency

(page 49).

Editing the Volume and Tonal Balance (Mixer)

CVP-809/CVP-805 Reference Manual

Equalizer (also called “EQ”) is a sound processor that divides the frequency spectrum into multiple bands that can be

boosted or cut as required to tailor the overall frequency response. The “Panel” – “Song Ch9-16” Part Selection tabs at the

top of the Mixer display let you adjust the EQ for each corresponding part, while “Master” lets you make overall EQ

adjustments for the entire instrument.

Part EQ (when one of the “Panel” – “Song Ch 9-16” tabs is selected)

Master EQ (when the “Master” tab is selected)

This instrument possesses a high-quality five-band digital EQ. With this function, a final effect — tone control — can be

applied to the output of your instrument. You can select one of the five preset EQ types in the “Master” display. You can

even create your own custom EQ settings by adjusting the frequency bands, and save the settings to one of two User

Master EQ types.

NOTE Master EQ cannot be applied to Audio playback or the Metronome sound.

EQ (Equalizer)

High

Boosts or attenuates the high EQ band for each part.

Low

Boosts or attenuates the low EQ band for each part.

80Hz 500Hz

1.0kHz 4.0kHz 8.0kHz

Bandwidth (also called “Shape” or “Q”)

Frequency

Gain

5 bands (default)

Editing the Volume and Tonal Balance (Mixer)

CVP-809/CVP-805 Reference Manual

1 Select the desired EQ type to be edited.

• Flat: Flat EQ settings. The gain of each frequency is set to 0dB.

•

Light: EQ setting for decreasing the level of the low frequencies, making the sound clearer.

•

Heavy: EQ setting for boosting the level of the low frequencies, making the sound more powerful.

•

Mellow: EQ setting for decreasing the level of the high frequencies, making the sound more mellow.

•

Bright: EQ setting for boosting the level of the high frequencies, making the sound brighter.

•

User1–30: Your own custom EQ settings saved in step 4.

2 Adjust the Q (bandwidth) and the Center Frequency of each band.

The available Frequency range is different for each band. The higher the value of Q, the narrower the bandwidth.

3 Boost or cut each of the five bands as desired.

4 Touch (Save) then save the settings as a User Master EQ type.

Up to two EQ types can be created and saved.

NOTICE

The settings will be lost if you turn the power to the instrument off without executing the Save operation.

NOTE If you want to save the Master EQ settings to the USB flash drive, save as a User Effect file. To do this, from the display

called up via [Menu]  [Utility]  [Factory Reset/Backup]  page 2/2, touch [Backup] of “User Effect” to execute the

Save operation (page 105).

This instrument features the following Effect Blocks.

•

System Effect (Chorus, Reverb): These Effects are applied to the entire sound of this instrument. For each part, you

can adjust the depth of the System Effect. Refer to “Chorus/Reverb” (page 14).

•

Insertion Effect 1 – 28 (CVP-809) / Insertion Effect 1 – 8 (CVP-805): These Effects are applied only to a

specific part. For each of these Effects, select an Effect type specifically for the desired part (for example, Distortion,

which would be applied only to the Guitar part).

•

Variation Effect: This Block can be used both as System Effects and Insertion Effects, and you can switch between

them.

These explanations cover the settings related to the Insertion Effects and Variation Effects on the Effect display. This

display is not available when the “Master” tab is selected at the top of the Mixer display.

Effects

Editing the Volume and Tonal Balance (Mixer)

CVP-809/CVP-805 Reference Manual

NOTE For details about the Effect types, refer to the “Effect Type List” in the Data List (separate PDF).

Editing and Saving the Effect settings

You can edit the settings of the System Effects (Chorus, Reverb), Insertion Effects and Variation Effect. The edits can be

saved as a User Effect type.

1 From the Mixer display, touch the desired Effect type to call up the Effect Type Selection

display.

2 Select the Effect type if necessary, then touch (Setting) to call up the Effect Parameter

display.

3 Make the necessary setting for each parameter.

The available parameters differ depending on the Effect type.

NOTE Parameters that are grayed out cannot be edited.

4 Touch (Save), then save the settings as a User Effect type.

Up to 30 Effect types can be stored for each of the Effect Blocks.

NOTICE

The settings will be lost if you turn the power to the instrument off without executing the Save operation.

NOTE If you want to save the Effect settings to a USB flash drive, save as a User Effect file. To do this, from the display called up

via [Menu]  [Utility]  [Factory Reset/Backup]  page 2/2, touch [Backup] of “User Effect” to execute the Save

operation (page 105).

Insertion Effect

Lets you assign the desired Insertion Effect Type for each part by touching the area above each

knob. You can adjust the degree to which each Effect is applied by using the knobs.

If you want to assign each of the Insertion Effects to a specific Part and select an Effect Type,

touch (Setting) at the upper right of this area and make necessary settings in the window.

The assignable Parts for each Insertion Effect are as follows:

 CVP-809

• Insertion Effect 1 – 19: Keyboard Parts, Song channels 1 – 16

• Insertion Effect 20: Microphone, Song channels 1 – 16

• Insertion Effect 21 – 28: Style Parts

 CVP-805

• Insertion Effect 1 – 5: Keyboard Parts, Song channels 1 – 16

•Insertion Effect 6: Microphone, Song channels 1 – 16

• Insertion Effect 7 – 8: Style Parts

Variati on Effect

Touch [Insertion] or [System] to switch the Effect Connection between the Insertion Effect and

System Effect, then touch the right end of this line to select the desired Effect type.

When “System” is selected, this Effect is applied to all parts of the Song and Style as the System

Effect. When “Insertion” is selected, this Effect is applied only to the specified Song/Style part.

To adjust the degree to which the Effect is applied, use the knob of each part.

Editing the Volume and Tonal Balance (Mixer)

CVP-809/CVP-805 Reference Manual

As described in the previous section, Chorus and Reverb are System Effects which are applied to the entire sound of the

instrument. They are not available when the “Master” tab is selected at the top of the mixer display.

When VRM Voices are selected, “VRM” indications appear under the knobs of the parts. If VRM Voices are selected for

multiple parts, the Chorus depth and the Reverb depth are applied commonly to all these parts.

NOTE For details about the Chorus and Reverb types, refer to the “Effect Type List” in the Data List (separate PDF).

Editing and Saving the Chorus/Reverb settings

Same as the operation on the “Effect” display (page 13).

Chorus/Reverb

Chorus

Touch the Chorus type name at the top right of this row to select the desired Chorus type. After

selecting, return to the Mixer display then use each knob to adjust the Chorus depth for each part.

Reverb

Touch the Reverb type name at the top right of this row to select the desired Reverb type. After

selecting, return to the Mixer display then use each knob to adjust the Reverb depth for each part.

Editing the Volume and Tonal Balance (Mixer)

CVP-809/CVP-805 Reference Manual

You can adjust the Pan (stereo position of the sound) and Volume for each Part. This display is not available when the

“Master” tab is selected at the top of the Mixer display.

Compressor is an effect commonly used to limit and compress the dynamics (softness/loudness) of an audio signal. For

signals that vary widely in dynamics, such as vocals and guitar parts, it “squeezes” the dynamic range, effectively making

soft sounds louder and loud sounds softer. When used with gain to boost the overall level, this creates a more powerful,

more consistently high-level sound.

This instrument features a Master Compressor which is applied to the entire sound of this instrument. Although preset

Master Compressor settings are provided, you can also create and save your original Master Compressor presets by

adjusting the related parameters. This display is available only when the “Master” tab is selected at the top of the Mixer

display.

NOTE Master Compressor cannot be applied to Audio playback or the Metronome sound.

Pan/Volume

Pan

Determines the stereo position of each part (channel).

Vol um e

Determines the level of each part or channel, giving you fine control over the balance of all the

parts.

Master Compressor

Editing the Volume and Tonal Balance (Mixer)

CVP-809/CVP-805 Reference Manual

1 Set the Compressor to “On.”

2 Select the Master Compressor type to be edited.

• Natural: Natural Compressor settings in which the effect is moderately pronounced.

• Rich: Rich Compressor settings in which the instrument’s characteristics are optimally brought out. This is good

for enhancing acoustic instruments, jazz music, etc.

• Punchy: Highly exaggerated Compressor settings. This is good for enhancing rock music.

• Electronic: Compressor settings in which the electronic dance music’s characteristics are optimally brought out.

• Loud: Powerful Compressor settings. This is good for enhancing energetic music such as rock or gospel music.

• User1–30: Your own custom Compressor settings saved in step 4.

3 Edit the parameters related to the Master Compressor.

The indication “GR” shows the Gain Reduction (compressed level) while “Output” shows the output level according

to the instrument sound in real time.

4 Touch (Save), then save the settings as a User Master Compressor type.

Up to 30 Master Compressor types can be created and saved.

NOTICE

The settings will be lost if you turn the power to the instrument off without executing the Save operation.

NOTE If you want to save the Master Compressor settings to a USB flash drive, save them as a User Effect file. To do this, from

the display called up via [Menu]  [Utility]  [Factory Reset/Backup]  page 2/2, touch [Backup] of “User Effect” to

execute the Save operation (page 105).

Compression

Parameters such as Threshold, Ratio and Soft Knee (which are available on commonly

used compressors) are all changed together at the same time, letting you moderately

compress the sound.

Te x tu r e

Adds natural characteristics to the effect. The higher the value, the lighter it becomes.

NOTE It may be easier to hear the changes when used in combination with “Compression” and

“Output.”

Output

Determines the output level.

Editing the Volume and Tonal Balance (Mixer)

CVP-809/CVP-805 Reference Manual

CVP-809

CVP-805

* MIC EFFECT = 3 Band EQ/Noise Gate/Compressor, VH = Vocal Harmony, VE = Vocal Harmony Effect

Block Diagram

CVP-809/CVP-805 Reference Manual 18

Editing Music Notation (Score) Settings

Select a MIDI Song then touch [Score] to call up the music notation of the current MIDI Song. You can change the

notation indication as desired to suit your personal preferences.

From the display called up via (Play Setting), you can set the parameters related to playback of the current MIDI

Song. The parameters explained here can also be set on the Song area (with expanded) of the Home display.

Indicates the name of the current Song. Also, the tempo value is shown at the right end. If you want to

change the Song, touch the Song name to call up the Song Selection display.

Lets you set the parameters related to playback Parts of the MIDI Song. For details, refer to “Play Setting”

(page 18).

Lets you set the notation indication parameters, including notation size, chord display, etc. For details, refer

to “View Setting” (page 19).

Lets you set more detailed parameters related to the notation indication. Refer to “Detail Setting” (page 19).

Play Setting

Extra

Turns playback of all Channels on or off, except for those assigned to the Left and Right Hand Parts

described below.

Left

Turns playback on or off for the Left Hand Part, to which you can assign the desired channel on the Song

Setting display (page 88).

Right

Turns playback on or off for the Right Hand Part, to which you can assign the desired channel on the

Song Setting display (page 88).

Guide

Turns the Guide function on or off. For details, refer to the Owner’s Manual, Chapter 5.

Turns Repeat playback on or off and lets you specify the Repeat playback range. For details, refer to the

Owner’s Manual, Chapter 5.

Editing Music Notation (Score) Settings

CVP-809/CVP-805 Reference Manual

From the display called up via (View Setting), you can set the parameters related to the view of the notation.

From the display called up via (Detail Setting), you can set more detailed parameters.

View Setting

Size

Determines the display resolution (or zoom level) of the notation.

Left

Turns indication of the left-hand notation on or off. If an “-” indication appears at this parameter and is

unavailable, go to the “Detail Setting” display (page 19), then set the Left Ch to any channel except

“Auto.” Or, on the display called up via [Menu] → [SongSetting] → [Part Ch], then set the Left to any

channel except “Off” (page 88).

NOTE Both Right (below) and Left cannot be turned off at the same time.

Right

Turns indication of the right-hand notation on or off.

NOTE Both Right and Left (above) cannot be turned off at the same time.

Chord

Turns indication of the chords on or off. If the current Song does not contain chord data, no chord

information is shown even if this is checked.

Lyrics

Turns indication of the Lyrics on or off. If the current Song does not contain lyrics data, no lyrics are

shown even if this is checked. If the Song contains Pedal events, touching here switches between “Lyrics”

and “Pedal.” When “Pedal” is checked, Pedal events are shown instead of Lyrics on the display.

Note

Turns indication of the Note names on or off. When this is checked, each note name is shown at the left

side of each note. If the Song contains Fingering events, touching here switches between “Note” and

“Fingering.” When “Fingering” is checked, Fingering events are shown instead of Note names on the

display.

Color

When this is checked, the notes in the display appear in identifying colors (C: red, D: yellow, E: green, F:

orange, G: blue, A: purple, and B: gray).

Detail Setting

Right Ch

Determines which MIDI channel in the MIDI Song data is used for the right-hand/left-hand part.

This setting returns to “Auto” when a different Song is selected.

•Auto:

The MIDI channels in the MIDI Song data for the right- and left-hand parts are assigned

automatically — setting each part to the channel which has been specified at the Part Ch (page 88) on

the Song Setting display.

•1–16: Assigns a specified MIDI channel (1–16) to each of the right- and left-hand parts.

•Off (Left Ch only): No channel assignment. This disables display of the left-hand notation.

Left Ch

Key

Signature

Lets you enter the Key Signature at the current stopped position of the MIDI Song. This setting is

useful for Songs you’ve recorded with key changes, so the key signature changes are properly

reflected in the notation.

Quantize

This gives you control over the note resolution in the notation, letting you shift or correct the timing

of all displayed notes so that they line up to a particular note value. Make sure to select the smallest

note value used in the Song.

Note Name

Selects the type of the note name indicated at the left of the note in the notation from among the

following three types. The settings here are available when the Note parameter (page 19) is checked.

•A, B, C:

Note names are indicated as letters (C, D, E, F, G, A, B).

•Fixed Do: Note names are indicated in solfeggio and differ depending on the selected language.

•Movable Do: Note names are indicated in solfeggio according to the scale intervals, and as such are

relative to the key. The root note is indicated as Do. For example, in the key of G major the root note of

“Sol” would be indicated as “Do.” As with “Fixed Do,” the indication differs depending on the selected

language.

CVP-809/CVP-805 Reference Manual 20

Editing Lyrics Display Settings

After selecting a Song, you can call up the lyrics of the current Song (if it contains lyrics data) by touching [Lyrics]. You

can change the lyrics indication as desired to suit your personal preferences.

NOTE When the lyrics are garbled or unreadable, you may need to change the Lyrics Language setting on the display called up via

[Menu]  [SongSetting]  [Lyrics].

Indicates the name of the current Song. Also, the current measure number for the MIDI Song or the elapsed

time for the Audio Song is shown at the right end. If you want to change the Song, touch the Song name here

to call up the Song Selection display.

Lets you set the parameters related to playback, such as playback parts for the MIDI Song or the Vocal

Cancel function for the Audio Song. For details, refer to “Play Setting” (page 18 for MIDI Songs, page 21 for

Audio Songs).

Allows you to change the background picture of the Lyrics display and Text display.

As well as various pictures provided in the Preset tab, you can select an original picture file (a bitmap file

with no greater than 800 x 480 pixels) in the USB flash drive. The original picture file can be copied from

the USB flash drive to the internal User memory.

NOTE The setting here is applied also to the Text display.

(only

Audio

Songs)

Lets you select the font type. “Medium” keeps each character at the same width, and “Proportional Medium”

changes the width depending on the characters.

Priority of Lyrics data of an Audio Song (MP3 file)

When showing the lyrics data of an Audio Song (MP3 file), only one type of data (according to the priority order

below) is shown:

1) CDG file (*.cdg) with the same name of the MP3 file in the same folder.

2) Lyrics in the MP3 file with the LYRICSBEGIN tag.

3) Lyrics in the MP3 file with the SLT/SYLT tag.

4) Lyrics in the MP3 file with the ULT/USLT tag.

5) Text file (*.txt) with the same name of the MP3 file in the same folder.

Editing Lyrics Display Settings

CVP-809/CVP-805 Reference Manual

From the display called up via (Play Setting), you can set the parameters related to playback of the current Audio

Song. The parameters explained here can also be set on the Song area (when expanded) of the Home display.

Play Setting (Audio Song)

Turns the Vocal Cancel function on/off. For details, refer to the Owner’s Manual, Chapter 5.

Turns the repeat playback on/off or specifies the repeat range. For details, refer to the Owner’s

Manual, Chapter 5.

CVP-809/CVP-805 Reference Manual 22

Showing the Text Display and Editing

Text Display Settings

Text files (.txt) of 60 KB or smaller created on a computer can be viewed on the instrument’s display. This feature enables

various useful possibilities, such as the showing of lyrics, chord names, and text notes.

If you want to view the text in a USB flash drive, connect the USB flash drive containing text data to the [USB TO

DEVICE] terminal beforehand.

1 Call up the Text display via [Menu] → [TextViewer].

2 Touch the bottom left corner on the display to call up the Text File Selection display.

3 Select the desired text file, and touch [Close] to show the text in the display.

If the text extends over several pages, you can scroll through the entire text by touching [] or [], which are

shown at the right and left of the page. To clear the text from the display, touch [×] located at right of the text file

name.

NOTE • Line breaks are not automatically entered in the instrument. If a sentence is not displayed in its entirety because of

limitations in the screen space, enter line breaks manually on your computer by using a text editor, etc. beforehand.

• Information about Text File selection can be memorized to the Registration Memory. For details, refer to the Owner’s

Manual, Chapter 8.

• The preset text files are sample data for the Playlist function. For details about Playlist, refer to the Owner’s Manual,

Chapter 8.

• The Text can be displayed on an external monitor or television. For details on instructions, refer to the Owner’s Manual,

Chapter 10.

Showing the Text Display

Page

Showing the Text Display and Editing Text Display Settings

CVP-809/CVP-805 Reference Manual

NOTE When the text is garbled or unreadable, you may need to change the language setting on the display called up via [Menu] 

[Utility]  [System].

Editing Text Display Settings

Indicates the current text file which is shown on the display. Touching here calls up the text File Selection

display which lets you select an original text file in the USB flash drive or copy it from the USB flash drive to

the internal User memory.

Clears the text from the display. This operation does not delete the text file itself, but simply leaves the

display empty of any text file.

Lets you set the parameters related to playback Parts of the MIDI Song. For details, refer to “Play Setting”

(page 18).

Allows you to change the background picture of the Lyrics display and Text display.

As well as various pictures provided in the Preset tab, you can select your original picture file (a bitmap file

with no greater than 800 x 480 pixels) in the USB flash drive. Your original picture file can be copied from

the USB flash drive to the internal User memory.

NOTE The setting here is applied also to the Lyrics display.

Lets you select the font size or type. “Small,” “Medium,” or “Large” keeps each character at the same width,

and is suitable for displaying lyrics with chord names above, etc. “Proportional Small,” “Proportional

Medium,” and “Proportional Large” are suitable for displaying lyrics without chord names or explanatory

notes.

CVP-809/CVP-805 Reference Manual 24

Using Keyboard Harmony

1 Set the Keyboard Harmony function to “On.”

When this is set to “On,” Harmony or Echo is applied to your keyboard performance automatically.

2 Adjust related parameters such as Harmony type and volume.

NOTE The available parameters differ depending on the Harmony type.

Type

Lets you select one of the Harmony types, which are divided into the following groups.

 Harmony Type (Standard Duet — Strum)

These types apply the harmony effect to notes played in the right-hand section of the

keyboard according to the chord specified in the left-hand section of the keyboard. (Note that

the “1+5” and “Octave” settings are not affected by the chord.)

If you want to use these types with the Style stopped, set the “Stop ACMP” parameter to a

setting other than “Disabled” in the Style Setting display (page 84).

When [ACMP ON/OFF] is turned on:

When the Left part is on:

When [ACMP ON/OFF] and

the Left part are on:

Split Point

Chord section for Style playback and Harmony effect

Split Point

Main and Layer Voices

Left Voice and chord section for Harmony effect

Style Split Point Left Split Point

Left Voice

Main and Layer Voices

Chord section for Style playback and Harmony effect

Using Keyboard Harmony

CVP-809/CVP-805 Reference Manual

Type  Multi Assign

The Multi Assign effect automatically assigns notes played simultaneously on the right-hand

section of the keyboard to separate parts (Voices). Both of the keyboard parts [Main] and

[Layer] should be turned on when using the Multi Assign effect. The Main and Layer Voices

are alternately assigned to the notes in the order you play.

 Echo Type (Echo, Tremolo and Trill)

When one of the Echo Types is selected, the corresponding effect (echo, tremolo, trill) is

applied to the note played in the right-hand section of the keyboard in time with the currently

set tempo, regardless of the [ACMP ON/OFF] and the Left part on/off status. Keep in mind

that Trill only works when you hold down two notes on the keyboard simultaneously (last two

notes if more than two notes are held), and it plays those notes alternately.

Volu me

This parameter is available for all types with the exception of “Multi Assign.” It determines the

level of the harmony/echo notes generated by the Harmony/Echo effect.

Speed

This parameter is only available when Echo, Tremolo, or Trill is selected in Type above. It

determines the speed of the Echo, Tremolo, and Trill effects.

Assign

This parameter is available for all types with the exception of “Multi Assign.” This lets you

determine the keyboard part via which the harmony/echo notes will be sounded.

•Auto:

Applies the effect to the part which is turned on. When the both parts are on, the Main

part is given priority over the Layer part.

•Multi: When both parts are on, the note played on the keyboard is sounded by Main part and

the harmonies (effect) are divided to the Main and Layer parts. When only one part is on, the

note played on the keyboard and effect are sounded by that part.

•Main, Layer: Applies the effect to the selected part (Main or Layer).

Chord Note

Only

This parameter is available when one of the Harmony Types is selected. When this is set to

“On,” the Harmony effect is applied only to notes (played in the right-hand section of the

keyboard) that belong to a chord played in the chord section of the keyboard.

Minimum

Vel oc ity

This parameter is available for all types with the exception of “Multi Assign.” It determines the

lowest velocity value at which the harmony note will sound. This allows you to selectively

apply the harmony by your playing strength, letting you create harmony accents in the

melody. The harmony effect is applied when you play the key strongly (above the set value).

CVP-809/CVP-805 Reference Manual 26

Microphone Settings

This section lets you set parameters for various Effects that are applied to the microphone sound. You should make both

“Vocal” and “Talk” settings — “Vocal,” for your singing performance, and “Talk,” for making announcements between

songs, for example.

Microphone

On/Off

Turns on or off the microphone sound. When set to On, the microphone sound will be input to

the instrument.

NOTE The setting here is equivalent to that in the Vocal Harmony display (page 28).

Voca l/Tal k

Switch

When you sing into the microphone for your performance, set this to “Vocal.” When you talk

normally or need to make announcements between songs of your performance, set this to

“Talk.” This lets you instantly change the microphone settings depending on the situation.

NOTE The setting here is equivalent to that in the Vocal Harmony display (page 28).

Vol um e

Adjustment

Adjusts the input volume of the microphone sound. The input level is shown at the right.

NOTE The setting here is equivalent to that in the Vocal Harmony display (page 28).

3 Band EQ

EQ (Equalizer) is a processor that divides the frequency spectrum into multiple bands which

can be boosted or cut as required to tailor the overall frequency response. The instrument

features a three-band (Low, Mid and High) digital equalizer function for the microphone

sound. For each of three bands, you can adjust the center frequency (Hz) and level (dB) via the

corresponding knobs on the display.

Noise Gate

This effect mutes the input signal when the input from the microphone falls below a specified

level. This effectively cuts off extraneous noise, allowing the desired signal (vocal, etc.) to pass.

On/Off

Turns Noise Gate on or off.

Th. (Threshold)

Adjusts the input level above which the gate begins to open.

Compressor

This effect holds down the output when the input signal from the microphone exceeds a

specified level. This is especially useful for smoothing out vocals that have widely varying

dynamics. It effectively “compresses” the signal, making loud parts softer, or vice versa.

On/Off

Turns Compressor on or off.

Th. (Threshold)

Adjusts the input level above which compression begins to be applied.

Ratio

Adjusts the compression ratio. Higher ratios result in a more compressed

sound, with a reduced dynamic range.

Output

Adjusts the final output level.

When “Vocal” is selected: When “Talk” is selected:

Microphone Settings

CVP-809/CVP-805 Reference Manual

NOTICE

The settings here are lost if you turn off the power without executing the Save operation.

NOTE When “Vocal” is selected, you can adjust Reverb/Chorus settings for your singing voice on the Mixer display (page 14).

You can store the microphone settings by touching (Save) then selecting one of 60 User Memories. For ease in future

recall, you should assign a sufficiently descriptive name or one that matches your performance.

To call up the microphone settings, touch the setting name at left of (Save) then select the desired file.

NOTE If you want to save the microphone settings to a USB flash drive, save as a User Effect file. To do this, on the display called up

via [Menu]  [Utility]  [Factory Reset/Backup]  page 2/2, touch [Backup] of “User Effect” to execute the Save operation

(page 105).

Pitch Detect

(only when

“Vocal” is

selected)

Lets you set how the pitch of the microphone sound during performance is detected.

Vocal Type

Set this to obtain the most natural vocal harmony, depending on your voice.

•Low:

Setting for lower voices. This setting is also appropriate for growling

and shouting.

•Mid: Setting for mid-range voices.

•High: Setting for higher voices. This setting is also appropriate for singing

close to the microphone.

•Full: Setting for vocalists having a wide range, from low to high.

Speed

Adjusts the response speed of the Vocal Harmony effect, or how quickly

harmonies are generated in response to your voice. The larger the number,

the faster the response.

NOTE When one or both of Lead Pitch Detect Speed and Harm Pitch Detect Speed

parameters of Vocal Harmony (page 31) are set to “as MIC SETTING,” this

parameter is effective. In other settings, the setting of the Vocal Harmony’s

Pitch Detect Speed is effective.

Background

Noise Cut

This allows you to filter out noises that would interfere with the pitch

detection. A setting of “Thru” turns the noise filter off.

Talk Mixing

(only when

“Talk” is

selected)

Lets you make settings for talking or making announcements between songs during a performance.

Pan

Determines the stereo pan position of the microphone sound.

Reverb Depth

Determines the depth of the reverb effects applied to the microphone sound.

Chorus Depth

Determines the depth of the chorus effects applied to the microphone sound.

Attenuator

Determines the amount of reduction to be applied to the overall sound

(excepting the microphone input) — allowing you to effectively adjust the

balance between your voice and the overall instrument sound.

Storing the Microphone Settings

CVP-809/CVP-805 Reference Manual 28

Vocal Harmony Settings

This section allows you to set various Vocal Harmony parameters, even though just selecting a Vocal Harmony Type will

call up the appropriate settings and you need not edit these parameters normally. If you want to make more detailed

settings for your performance, read this chapter.

NOTE The settings here are equivalent to those in the Microphone Setting display (page 26).

Basic Parameters

Microphone On/Off

Turns the microphone sound on or off. When this is set to On, the microphone

sound is input to the instrument.

Vocal/Talk Switch

When you sing into the microphone, this should be set to “Vocal.” When you talk

normally or make announcements between songs, this should be set to “Talk.” If

you want to set the Vocal Harmony parameters, this should be set to “Vocal.”

Volume Adjustment

Adjusts the input volume of the microphone sound. The input level is shown at the

right.

Vocal Harmony name

Vocal Harmony Settings

CVP-809/CVP-805 Reference Manual

By editing the parameters of the preset Vocal Harmony type, you can create your original Vocal Harmony type.

1 Touch the Vocal Harmony name to call up the Vocal Harmony Selection display.

2 Select the desired Vocal Harmony type.

3 Depending on the selected Vocal Harmony type, edit the relevant settings as desired.

 Harmony

Lets you edit the Vocal Harmony parameters.

Editing the Vocal Harmony Type

Harmony

On/Off

Turns Vocal Harmony on or off.

Mode

Although one of the three following Modes is automatically selected when a Vocal

Harmony type is selected, you can change the Mode.

Chordal

The harmony notes are determined by the following three chord

types: chords played in the chord section of the keyboard (with

[ACMP ON/OFF] turned on), chords played in the left hand

section of the keyboard (with the Left part turned on), and chords

contained in Song data for controlling the harmony. (Not available

if the Song does not contain any chord data.)

NOTE If you want to apply Vocal Harmony by pressing the chords in the

chord section when the Style is stopped, you need to set the “Stop

ACMP” parameter to a setting other than “Disabled” in the Style

Setting display (page 84).

Vo co der

The microphone sound is output via the notes you play on the

keyboard or via the Song playback notes.

Vo co der-Mo no

Basically the same as the Vocoder. In this mode, only single-note

melodies or lines can be played back (with last-note priority).

(When the Mode is set to “Chordal”)

Chord

Source

Determines which data or event of a Song will be used for chord detection.

•Off:

Detects no chord from the Song data.

•XF: Chord data defined via XF will be used.

• 1 – 16: Detects a chord from notes of the MIDI channel specified here.

When the Mode ( ) is set to “Chordal”:

When the Mode ( ) is set to “Vocoder” or “Vocoder-Mono”:

Vocal Harmony Settings

CVP-809/CVP-805 Reference Manual

Type

Determines how the harmony notes are applied to the microphone sound by selecting

one of the Chordal Types. Almost all Types apply the harmony notes based on the chord

specified via the left hand section of the keyboard, chord section of the keyboard, or the

Song data, with the exception of the following two Types. For details, refer to the “Vocal

Harmony Parameter List” in the Data List (separate PDF.)

•ScaleDiatonic:

This generates harmony notes based on the Key Root and Key Type

specified in the Harmony Assign display ( ), meaning that the harmony notes do not

depend on the chord but match the diatonic scale of the current song’s key signature.

• Parallel: This adds a note to the lead note (microphone sound) with the interval specified

at , regardless of the chord.

NOTE “Abv” in the Chordal Type List means that the harmony notes are generated above the lead

note (microphone sound) while “Blw” means that the harmony notes are generated below

the lead note.

For more information about the Chordal Types, refer to “Vocal Harmony Parameter

List” in the Data List (separate PDF).

(When the Mode is set to “Vocoder” or “Vocoder-Mono”)

Song Ch

When set to one of 1 – 16, note data (played from a Song on this instrument or the

connected computer) of the corresponding channel is used to control the harmony.

When set to “Off,” Song data control over harmony is turned off.

Part

When set to “Mute,” the channel selected above (to control Harmony) is muted (turned

off) during Song playback, allowing you to disable control via specific channels as

desired.

Keyboard

•Off: Keyboard control over harmony is turned off.

•Upper: Notes played to the right of the Split Point control the harmony.

•Lower: Notes played to the left of the Split Point control the harmony.

Balance

Lets you set the balance between the lead vocal (the microphone sound) and Vocal

Harmony sound. Raising this value increases the volume of the Vocal Harmony and

decreases that of the lead vocal. When this is set to L<H63 (L: Lead Vocal, H: Vocal

Harmony), only the Vocal Harmony is output; when it is set to L63>H, only the lead

vocal is output.

Balance

adjustment

for each Lead

note and

Harmony

note

The following parameters can be adjusted for each Lead note (microphone sound) and

Harmony note.

• Transpose/Degree:

Lets you shift the pitch for each Harmony note and Lead note. The

range for all notes is the same; however, the lead note can only be adjusted in octaves.

When the Chordal Type is set to “ScaleDiatonic,” this parameter changes to Degree, letting

you shift the pitch in degree from -3 octaves (-22 scale degrees) – Unison (1 scale degree) –

+3 octaves (+22 scale degrees).

• Detune: Determines the fine pitch setting for each Harmony note from -50 cents to +50

cents.

•Formant: Determines the formant setting for each Harmony note. The higher the value,

the more “feminine” the harmony voice becomes. The lower the value, the more

“masculine” the voice.

•Pan: Determines the pan position setting for each Harmony note. Setting each Harmony

note to a different pan position, with the Lead vocal at center, for example, results in a

naturally wide stereo sound.

• Volume: Determines the volume setting for each Harmony note. Use this to adjust the

relative level balance among the Lead vocal and the Harmony notes.

NOTE When Pitch Correct Mode ( ) is set to OFF the Lead part is not available for the

Transpose/Degree, Detune and Formant parameters.

NOTE The Transpose values of the Harmonies are available only when the Mode ( ) is set to

“Chordal.”

Vocal Harmony Settings

CVP-809/CVP-805 Reference Manual

 Effect

Lets you edit the parameters related to the Effects applied to the Vocal Harmony notes.

Harmony

Assign

Lets you set how the Harmony notes are assigned or voiced to the Lead note

(microphone sound). For details, refer to “Vocal Harmony Parameter List” in the Data

List (separate PDF).

 When the Harmony mode is set to “Chordal”

•Session Table: Determines how the harmonies will be voiced, or what type of chord will

be used in creating the harmonies, according to different musical styles.

NOTE This parameter is available only when the Chordal Type is set to something other than

ScaleDiatonic or Parallel.

•Key Root, Key Type: When the Chordal Type ( ) is set to “ScaleDiatonic,” this

parameter is available. Harmony notes based on the settings here do not depend on the

chord but match the diatonic scale of the current song’s key signature.

 When the Harmony mode is set to “Vocoder” or “Vocoder-Mono”

•Transpose Mode: Determines the amount by which the harmony parts are transposed. A

setting of “0” results in no transposition, while the “Auto” setting results in automatic

transposition.

Detail

Setting

•Pitch Correct Mode: Corrects the pitch of the Lead note (microphone sound). “Off” does

not correct while “Hard” corrects the pitch most accurately.

•Humanize: This setting allows you to make the Vocal Harmony sounds more natural and

less “electronic,” by introducing slight time discrepancies between the Lead and Harmony

notes.

Off: No Humanize effect.

The Humanize effect is applied to the Harmony to create a more natural feel, with an

authentic-sounding widening effect, giving the impression of more people singing.

2: The Humanize effect is applied to the Harmony to produce a more distinct groove. Even

faster passages retain their rhythmic essence.

3: The Humanize effect is applied to the Harmony to reflect the way in which the lead

vocalist and back chorus interact, with the lead vocal out front, and the timing slightly

relaxed.

• Lead Pitch Detect Speed, Harm Pitch Detect Speed: Determines how fast the pitch of

the Lead note and the harmony notes are detected in response to the signal via the

microphone. “1” responds most slowly, “4” is standard, “15” responds most quickly, and “as

MIC SETTING” gives priority to the speed specified at the Pitch Detect “Speed” of the

Microphone Setting display (page 27).

•Harmony Effect: Determines the Effect type applied to the Harmony notes added to the

Lead note.

•Harmony Stability: Determines the stability degree to which the Harmony is applied to

the Lead note. When set to “Stable,” this has a relatively stable sound with little harmony

motion. When set to “Dynamic,” this tends to add harmony with motion according to the

input sound.

•Lead Vibrato Depth: This specifies the vibrato depth of the lead sound.

•Harm Vibrato Depth: This specifies the vibrato depth of the harmony sound.

• Vibrato Speed: This specifies the vibrato speed of both the lead and harmony sounds.

•Vibrato Delay: This specifies the vibrato delay of both the lead and harmony sounds.

For more information about the parameters of Detail Settings, refer to “Vocal Harmony

Parameter List” in the Data List (separate PDF).

Effect On/Off

Turns on or off the Effects applied to the Vocal Harmony notes.

Type

Selects the Effect type applied to the Vocal Harmony notes. You can edit also the

detailed parameters of the selected type. For details, refer to “Vocal Effect Type List” and

“Vocal Harmony Parameter List” in the Data List (separate PDF).

To L ead

Adjusts the Effect depth applied to the Lead note.

To Harmony

Adjusts the Effect depth applied to the Harmony notes.

Vocal Harmony Settings

CVP-809/CVP-805 Reference Manual

4 Touch (Save), then save the edits as an original Vocal Harmony type.

Up to 60 Vocal Harmony types can be saved to User memory. For ease in future recall, you should assign a

descriptive name that matches the settings.

NOTICE

The settings here are lost if you turn off the power without executing the Save operation.

NOTE If you want to save the Vocal Harmony settings to a USB flash drive, save as a User Effect file. To do this, on the display

called up via [Menu]  [Utility]  [Factory Reset/Backup]  page 2/2, touch [Backup] of “User Effect” to execute the

Save operation (page 105).

Reverb Depth

Adjusts the Reverb depth applied to the microphone sound. This setting is equivalent to

that in the Mixer display (page 14).

Chorus Depth

Adjusts the Chorus depth applied to the microphone sound. This setting is equivalent

to that in the Mixer display (page 14).

CVP-809/CVP-805 Reference Manual 33

Using Playlist

By importing Music Finder Records (.mfd) used on previous Yamaha digital pianos (such as CVP-709, 705 etc.), you can

use the Records on the Playlist of this instrument, just like using the Music Finder function on those other instruments.

For details on using Music Finder, refer to the Owner’s Manual of the Yamaha digital piano which contains your desired

Music Finder Records.

1 Connect the USB flash drive which contains the Music Finder file (***.mfd) to the [USB TO

DEVICE] terminal.

2 On the Playlist display, touch the Playlist file name to call up the Playlist File Selection

display.

3 Select the desired Music Finder file to call up a confirmation message.

4 Touch [Yes] to start importing.

The imported Music Finder Records will be converted to Registration Memory Bank files and saved to a folder

(with the same name as the imported file) in the User drive of this instrument. At the same time, a Playlist of the

converted Registration Memory Bank files (with the same name as the imported file) will be created in the USB

flash drive. The Music Finder settings are registered to the Registration Memory number [1] for each Bank.

NOTICE

If a folder with the same name as the Music Finder file already exists, the Registration Memory Bank file with the

same name in that folder will be overwritten by the importing data. To avoid overwriting important data, change the

folder name or the Music Finder file name.

5 Turn the [OTS LINK] button on to enable to use of the imported Records in the same way as

the original Music Finder function.

Importing Music Finder Records to the Playlist

Using Playlist

CVP-809/CVP-805 Reference Manual

6 Touch the Record name on the Playlist display and load the settings contained in the Music

Finder data.

Searching for Records

Since Music Finder data is saved to Registration Memory, you can search for Records on the Registration Bank

Selection display. The keyword and genre of the Music Finder are saved as tag information. For details about

searching or tags, refer to the Owner’s Manual, Chapter 8.

CVP-809/CVP-805 Reference Manual 35

Calling Up Registration Memory Numbers

in Order (Registration Sequence)

For changing the panel setup quickly during a live performance, this instrument features the Registration Sequence which

lets you call up the eight setups in any order you specify, by simply using the ASSIGNABLE buttons or the pedal as you

play.

1 On the Home display, touch [] at the upper right corner to show the Registration area, then

touch the area to call up the Registration Bank Selection display.

2 Select the desired Registration Memory Bank to create a sequence.

3 Call up the Registration Sequence display via [Menu] → [RegistSeq].

4 Specify how the pedal or ASSIGNABLE button will be used.

If you intend to use a pedal to switch the Registration Memory number, the pedal assigned to “Regist +” will be used

for advancing through the sequence. The pedal assigned to “Regist -” will be used for reversing through the

sequence.

NOTE You can also assign the other functions to the pedal — Punch In/Out of Song (page 89) and the function set in the

Assignable display (page 43). If you assign multiple functions to the pedal, the priority is: Punch In/Out of Song 

Registration Sequence  the function set in the Assignable display.

If you intend to use the ASSIGNABLE button to switch the Registration Memory number, assign “Regist +” or

“Regist -” in the display called up via [Menu] → [Assignable] → [Assignable] (page 46).

Indicates the Registration

Memory numbers, in the

order of the current

Registration Sequence.

Current Registration

Bank name

Calling Up Registration Memory Numbers in Order (Registration Sequence)

CVP-809/CVP-805 Reference Manual

5 Program a Sequence order in which the Registration Memory number is to be called up.

Basically, press the desired Registration Memory number button on the panel, then touch [Insert] to enter the

selected number.

6 Select the action that will result when the Registration Sequence reaches the end.

• Stop: Pressing the ASSIGNABLE button or the “advance” pedal has no effect. The sequence is “stopped.”

•

Top : The sequence starts again at the beginning.

•

Next: The sequence automatically moves to the beginning of the next Registration Memory Bank in the same

folder.

7 Set the Registration Sequence to “On.”

The Registration Sequence programmed here is shown in the Registration area of the Home display. Press the pedal

or the ASSIGNABLE button to check whether or not the Registration Memory number is called up in the order as

programmed.

8 Touch (Save) to call up the File Selection display, then save the sequence program as a

Registration Memory Bank file.

NOTICE

Settings in the Registration Sequence display will be lost if you select another Registration Bank without

executing the Save operation.

, , , I

Moves the cursor.

NOTE If you want to move the cursor directly to an already entered number, touch the desired

number.

Replace

Replaces the number of the cursor location with the currently selected Registration

Memory number.

Insert

Inserts the number of the currently selected Registration Memory number before the

cursor position.

Delete

Deletes the number at the cursor position.

Clear

Deletes all numbers in the sequence.

CVP-809/CVP-805 Reference Manual 37

Disabling Recall of Specific Items

(Registration Freeze)

Registration Memory lets you recall all the panel setups you made with a single button press. However, there may be times

that you want certain items to remain the same, even when switching Registration Memory setups. For example, you may

want to switch Voice settings while keeping the same Style. This is where the Freeze function comes in handy. It lets you

maintain the settings of certain items and leave them unchanged, even when selecting other Registration Memory

buttons.

1 Enter the checkmark of the item to be “frozen.”

2 Set the Registration Freeze to “On.”

CVP-809/CVP-805 Reference Manual 38

Playing Styles Automatically with Your

Custom Chord Progressions (Chord Looper)

Normally, while playing along with a Style, you play chords in the chord section of the keyboard. However, by using the

Chord Looper function, you can record chord progressions you want to play over, and the Style can be played back in a

loop responding to the chord progression data. For example, if you play the chords C, F, G and C in order and record it,

the Style loops and keeps playing back as “C / F / G / C → C / F / G / C ...” —without the need for you to play chords in the

chord section of the keyboard. This extends your performance capability, letting you play freely with both your left and

right hands.

1 Select the desired Style.

As necessary, adjust the tempo.

2 Call up the Chord Looper display.

3 While playing back a Style, touch [Rec/Stop] on the display.

[Rec/Stop] flashes to indicate recording is in standby. On the next measure of the Style, [Rec/Stop] is turned on and

the recording starts.

NOTE When [Rec/Stop] is turned on, the [ACMP] button is turned on automatically.

NOTE If you turn on [Rec/Stop] while the Style is stopped, the [SYNC START] button is turned on automatically and lets you start

recording when you play a chord in the chord section.

4 Play the chords in the chord section, according to the playback tempo of the Style.

Playing while using Chord Looper

During recording

Playing Styles Automatically with Your Custom Chord Progressions (Chord Looper)

CVP-809/CVP-805 Reference Manual

5 At the timing just before the measure you want to start loop playback, touch [On/Off] to

stop recording.

[On/Off] flashes to indicate loop playback is in standby. On the next measure of the Style, [On/Off] is turned on

and the Style will be played back in a loop in response to the recorded chord progression.

During loop playback, [On/Off] lights and the [ACMP] button flashes. At this time, chord input in the chord

section is not detected, and the whole keyboard can be used for performance.

6 Touch [On/Off] to stop loop playback of the Style, and you can play back the Style normally

by playing chords in the chord section.

Turning on [On/Off] starts loop playback again in response to the chord progressions recorded in steps 3–5.

NOTE The latest chord progression data you recorded is maintained unless you turn the power off or select a Chord Looper

Memory number which contains data. If you want to save the data, go on to step 2 on page 40.

During loop playback

Playing Styles Automatically with Your Custom Chord Progressions (Chord Looper)

CVP-809/CVP-805 Reference Manual

The recorded chord progression data can be memorized to the Chord Looper Memory locations [1] – [8], and these eight

patterns of data can be saved as a single Chord Looper Bank file.

NOTE The Chord Looper Memory can also be saved (or exported) in single, individual patterns (page 42).

1 Record the desired chord progressions (steps 1 – 5 on page 38).

You can stop recording also by turning [Rec/Stop] off or pressing the STYLE CONTROL [ / ] (START/STOP)

button, instead of touching [On/Off].

NOTICE

If you select a Chord Looper Memory number which contains the memorized data or turn off the power to the

instrument before going to the next step, the chord progression data you’ve recorded will be lost.

2 Confirm the data has been recorded, and then touch [Memory].

If the recorded data exists, the letters of [On/Off] at the right bottom of the display are shown in white.

3 Touch the desired Chord Looper Memory number ([1] – [8]) to memorize the chord

progression data.

When the data is memorized, the chord progression is shown in the cell of the selected number. If there is not

enough space to show all the chords, some chords are omitted.

4 As necessary, repeat steps 1 – 3.

5 Touch (Save) to save the data in the Chord Looper Memory [1] – [8] as a single Bank file.

NOTICE

If you select another Chord Looper Bank file or turn off the power to the instrument before saving the file, the

memorized data will be lost.

NOTE Each Chord Looper Memory is named automatically such as “CLD_001,” but it can be renamed by exporting the file

(page 42).

Saving the Recorded Data as a Bank File

Chord Looper Memory

(Eight data slots are saved as

a single file)

Recorded

data exists

No recorded

data

Playing Styles Automatically with Your Custom Chord Progressions (Chord Looper)

CVP-809/CVP-805 Reference Manual

1 Touch the Chord Looper Bank name to call up the Chord Looper Bank Selection display, and

select the desired Bank.

2 Touch the Chord Looper Memory number you wish to use first.

If you want to start loop playback of the Style from the beginning of your performance, touch and turn on [On/Off].

3 Start playback of the Style and play along with it.

4 Turn on [On/Off] just before the measure you want to start loop playback of the Style.

[On/Off] flashes to indicate loop playback is in standby. On the next measure of the Style, [On/Off] is turned on

and the Style will be played back in a loop.

During loop playback, [On/Off] lights and the [ACMP] button flashes. At this time, chord input in the chord

section is not detected, and the whole keyboard can be used for performance.

5 As necessary, change the Chord Looper Memory number or turn loop playback on/off by

touching [On/Off].

Recalling a Chord Looper Bank File and Playing back a Style in

a Loop

Chord Looper Bank file name

Playing Styles Automatically with Your Custom Chord Progressions (Chord Looper)

CVP-809/CVP-805 Reference Manual

Each Chord Looper Memory number can be deleted, saved, or recalled one by one. Eight Chord Looper Memories

(progressions) can be saved as a single Bank file.

1 Touch the desired action.

2 Touch the desired Chord Looper Memory number to execute the action.

3 As necessary, touch (Save) to save the edited data as a Chord Looper Bank file.

NOTICE

If you select another Chord Looper Bank file or turn off the power to the instrument before saving the file, the

edited data will be lost.

If you want to clear all data shown in the Chord Looper display, touch (New Bank) to create a new Bank.

Editing the Chord Looper Bank file

Clear

Deletes the data in the specified Chord Looper Memory number.

Import

Imports the Chord Looper Memory data saved (or exported) to User memory or USB flash drive

to the specified Chord Looper Memory number.

Export

Saves the data in the specified Chord Looper Memory number to User memory or USB flash

drive. The file name is entered automatically, but you can rename it when saving.

CVP-809/CVP-805 Reference Manual 43

Assigning a Specific Function to Each

Pedal or ASSIGNABLE button

You can assign various functions to the three pedals of the instrument, instead of the original functions (damper,

sostenuto and soft). Likewise, various functions can be assigned to the Footswitch or Foot Controller connected to the

[AUX PEDAL] jack.

1 Select the function for each pedal.

For information about each function, refer to pages 44 – 45.

NOTE You can also assign other functions to the pedal — Punch In/Out of Song (page 89) and Registration Sequence

(page 35). If you assign multiple functions to the pedal, the priority is: Punch In/Out of Song  Registration Sequence 

Functions assigned here.

2 Touch (Setting), then make the detailed settings of the selected functions.

For each Part, you can turn on or off the selected function and adjust the degree to which the selected function is

applied. Depending on the function selected in Step 1, the available parameters differ, or (Setting) is grayed out

indicating that there is no available parameters.

3 If necessary, set the polarity of the footswitch or foot controller connected to the [AUX

PEDAL] jack.

Depending on the Footswitch or Foot Controller, it may work in the opposite way (i.e., pressing it has no effect, but

releasing it does). If such a case occurs, use this setting to reverse the polarity.

4 If you change the functions of the Center and Left pedals from the default settings, turn

“Switch With Main Voice(Center & Left)” on or off as desired.

When this is set to off, the function assignments of the Center and Left pedals are maintained even if the Main Voice

is changed (page 50).

Pedal

Assigning a Specific Function to Each Pedal or ASSIGNABLE button

CVP-809/CVP-805 Reference Manual

Assignable Pedal Functions

For functions indicated with “*1”, use only the Foot Controller; proper operation cannot be done with a Footswitch.

For functions indicated with “*2”, they can be assigned also to the ASSIGNABLE [1] – [4] buttons.

Articulation 1/2

When you use a Super Articulation Voice that has an effect assigned to the pedal/

footswitch, you can enable the effect by pressing the pedal/footswitch.

Vol um e

Controls the volume. This function is available only for the foot controller connected

to the instrument’s [AUX PEDAL] jack.

Sustain

Controls the sustain. When you press and hold the pedal, all notes played on the

keyboard have a longer sustain. Releasing the pedal immediately stops (damps) any

sustained notes. The “Half Pedal Point” parameter allows you to specify how far down

you should press on the pedal until the damper effect starts working. This can be set

for all pedals on the CVP-809, as well as the right pedal and the foot controller

connected to the [AUX PEDAL] jack on the CVP-805.

Sostenuto

Controls the Sostenuto effect. If you play a note or chord on the keyboard and press the

pedal while holding the note(s), the notes will sustain as long as the pedal is held.

However, all subsequent notes will not sustain. This makes it possible to sustain a

chord, for example, while other notes are played staccato.

NOTE This function will not affect any of the Organ Flutes and only some of the Super

Articulation Voices.

Soft

Controls the Soft effect. Pressing this pedal reduces the volume and changes the timbre

of the notes you play. This is effective only for certain appropriate Voices. The “Half

Pedal Point” parameter allows you to specify how far down you should press on the

pedal until the soft effect starts working. This can be set for all pedals on the CVP-809,

as well as the right pedal and the foot controller connected to the [AUX PEDAL] jack

on the CVP-805.

Glide

When the pedal is pressed, the pitch changes, and then returns to normal pitch when

the pedal is released.

•Up/Down:

Determines whether the pitch change goes up (is raised) or down (is

lowered).

•Range: Determines the range of the pitch change, in semitones.

• On Speed: Determines the speed of the pitch change when the pedal is pressed.

• Off Speed: Determines the speed of the pitch change when the pedal is released.

Portamento

The portamento effect (a smooth slide between notes) can be produced while the pedal

is pressed. Portamento is produced when notes are played legato style (i.e., a note is

played while the preceding note is still held). The portamento time can also be adjusted

form the Voice Edit display (page 48). This function does not affect certain Natural

Voices, which would not sound appropriately with this function.

NOTE This function will not affect any of the Organ Flutes, Super Articulation 2 Voices (CVP-809

only) and only some of the Super Articulation Voices.

Pitch Bend

Allows you to bend the pitch of notes up or down by using the pedal. This function can

be assigned to all pedals on the CVP-809, as well as the right pedal and the foot

controller connected to the [AUX PEDAL] jack on the CVP-805.

•Up/Down:

Determines whether the pitch change goes up (is raised) or down (is

lowered).

•Range: Determines the range of the pitch change, in semitones.

Modulation +/-

Applies a vibrato effect to notes played on the keyboard. Moreover, various effects can

be added to the Super Articulation Voice. The effect becomes deeper when pressing

down the foot controller.

Modulation (Alt) +/-

Unlike the Modulation above, pressing the pedal or footswitch alternates the on/off

status of the vibrato effect.

Vibe Rotor On/Off

Switches the Vibe Rotor on and off when the Insertion Effect Type (page 50) is set to

“VibeRotor” in the “Legacy” category.

Assigning a Specific Function to Each Pedal or ASSIGNABLE button

CVP-809/CVP-805 Reference Manual

Organ Rotary Slow/

Fast

Switches the Rotary Speaker speed (page 51) between “Slow” and “Fast.”

Keyboard Harmony On/

Off

Switches the Keyboard Harmony (page 24) function on and off.

Vocal Harmony On/Off

Switches “Harmony” in the Vocal Harmony display on and off (page 29).

Vocal Harmony Effect

On/Off

Switches “Effect” in the Vocal Harmony display on and off (page 31).

Talk On/Off

Switches between “Vocal” and “Talk” in the Microphone Setting display (page 26).

Score Page +/-

While the Song is stopped, you can turn to the next/previous score page (one page at a

time).

Lyrics Page +/-

While the Song is stopped, you can turn to the next/previous lyrics page (one page at a

time).

Text Pag e +/-

You can turn to the next/previous text page (one page at a time).

Song Play/Pause

Same as the SONG CONTROL [ / ] (PLAY/PAUSE) button.

Style Start/Stop

Same as the STYLE CONTROL [ / ] (START/STOP) button.

Tap Tempo

Same as the [TAP TEMPO] button.

Synchro Start

Same as the [SYNC START] button.

Synchro Stop

Same as the [SYNC STOP] button.

Intro 1 – 3

Same as the INTRO [I] – [III] buttons.

Main A – D

Same as the MAIN VARIATION [A] – [D] buttons

Fill Down

Plays a fill-in, which is automatically followed by the Main section of the button on the

immediate left.

Fill Self

Plays a fill-in.

Fill Break

Plays a break.

Fill Up

Plays a fill-in, which is automatically followed by the Main section of the button on the

immediate right.

Ending 1 – 3

Same as the ENDING/rit. [I] – [III] buttons.

Half Bar Fill In

While the pedal is pressed, the “Half bar fill-in” function is turned on and changing

sections of a Style at the first beat of the current section starts the next section from the

middle with automatic fill-in.

Fade In/Out

Switches Fade In /Fade Out function on and off.

Fingered/

Fingered On Bass

The pedal alternately switches between the Fingered and On Bass modes (page 6).

Bass Hold

While the pedal is pressed, the Style bass note will be held even if the chord is changed

during Style playback. If the fingering is set to “AI Full Keyboard,” the function does

not work.

Percussion

The pedal plays a percussion instrument selected in the window called up via

(Setting). In this window, you can use the keyboard to select an instrument.

NOTE When you select the percussion instrument by pressing a key on the keyboard, the

velocity with which you press the key determines the percussion volume.

Main Voice On/Off

Turns the Main Voice on or off.

Layer Voice On/Off

Turns the Layer Voice on or off.

Left Voice On/Off

Turns the Left Voice on or off.

OTS +/-

Calls up the next/previous One Touch Setting.

Assigning a Specific Function to Each Pedal or ASSIGNABLE button

CVP-809/CVP-805 Reference Manual

You can assign a specific function to each of the ASSIGNABLE [1] – [4] buttons, letting you call up often used functions

quickly. Likewise, you can also assign each of the icons shown in the Menu display to each of these buttons.

1 Select the item for each of ASSIGNABLE buttons.

You can assign the icons shown in the Menu display (with the exception of Assignable, Wireless LAN, Time and

Bluetooth), Pedal Functions marked with “*2” (page 44), and the following functions. If you want no function to be

assigned, select “No Assign.”

2 If necessary, touch (Setting) then make the detailed settings.

You can turn on or off the specified function for each Part. Depending on the selected function, (Setting) is

grayed out, indicating that there are no available parameters.

Assignable

Left Hold On/Off

Turns on or off the Left Hold.

Effect On/Off

Turns on or off the Effects.

Mono/Poly

Switches between the Mono (in which the Keyboard Voice is played monophonically with

the last note priority) and Poly (in which the Keyboard Voice is played polyphonically).

Depending on the Voice, Portamento may be produced when notes are played with legato.

Regist +/-

Calls up the next/previous Registration Memory number of the Registration Sequence.

CVP-809/CVP-805 Reference Manual 47

Editing a Voice (Voice Edit)

The Voice Edit feature allows you to create your own Voices by editing some parameters of the existing Voice. Once you’ve

created a Voice, you can save it as a User Voice for future recall. This section covers the editing of Voices other than Organ

Flutes Voices, since the method of editing is different between them. For instructions on editing Organ Flutes Voices,

refer to page 51.

1 Select the desired Voice (other than an Organ Flutes Voice).

2 On the Voice Edit display called up via [Menu] → [VoiceEdit], select the desired parameter

then edit the value.

For information about the editable parameters, refer to page 48.

By touching (Compare) repeatedly, you can compare the sound of the edited Voice with the original (unedited)

Voice.

3 Touch (Save) to save the edited Voice.

NOTICE

The settings will be lost if you select another Voice or turn the power to the instrument off without executing the

Save operation.

NOTE If you want to edit another Voice, touch the Voice name at the top of the Voice Edit display. Or, press the VOICE [MAIN/

LAYER/LEFT] button to select the Keyboard part to which the desired Voice is assigned, confirm the Voice name at the

top of the Voice Edit display, make the edits as desired, then execute the Save operation.

Editing a Voice (Voice Edit)

CVP-809/CVP-805 Reference Manual

Editable Parameters in the Voice Edit display

Common

Volu me

Adjusts the volume of the current edited Voice.

To u c h

Sensitivity

Depth

Adjusts the touch sensitivity (velocity sensitivity), or how greatly the volume

responds to your playing strength.

•Depth:

Determines the velocity sensitivity, or how much the level of the Voice

changes in response to your playing strength (velocity).

•Offset: Determines the amount by which received velocities are adjusted for the

actual velocity effect.

Offset

Part Octave Main/Layer

Shifts the octave range of the edited Voice up or down in octaves. When the edited

Voice is used as any of the Main and Layer parts, the Main/Layer parameter is

available; when the edited Voice is used as the Left part, the Left parameter is

available.

Left

Mono Mono/Poly

Determines whether the edited Voice is played monophonically or polyphonically.

Mono Type

Determines the behavior of the notes of decaying sounds, such as a guitar, when

they are played with legato with the edited Voice set to “Mono” above.

•Normal:

The next note sounds after the previous note is stopped.

•Legato: The sound of the previously played note is maintained and only the pitch

changes to that of the next note.

•Crossfade: The sound smoothly transitions from the previously played note to the

next note.

NOTE This parameter is unavailable for Super Articulation Voices, Drum/SFX Kit Voices and

Organ Flutes Voices, and behaves the same as the “Normal” setting when these

Voices are selected.

NOTE When Legato is selected, the behavior (other than what is described here) may be

different from Normal, depending on the panel settings.

Portamento

Time

Sets the portamento time (pitch transition time) when the edited Voice is set to

“Mono” above.

NOTE The Portamento Time determines the pitch transition time. Portamento is a function

that creates a smooth transition in pitch from the first note played on the keyboard to

the next.

127

Touch Sensitivity Depth

Changes the velocity curve according to

Velocity Depth (with Offset set to 64)

Touch Sensitivity Offset

Changes to velocity curve according to Velocity

Offset (with Depth set to 64)

Actual Velocity for

tone generator

Depth = 127 (twice)

Depth = 64 (normal)

Depth = 32 (half)

Depth = 0

Received Velocity

(Actual Key-on speed)

Actual Velocity for

tone generator

Depends on

offset

Depends on

offset

Offset = 96 (+64) Offset = 127 (+127)

Offset = 64

(normal)

Offset = 32 (-64)

Received Velocity

(Actual Key-on speed)

Offset = 0 (-127)

Editing a Voice (Voice Edit)

CVP-809/CVP-805 Reference Manual

Sound

Filter

Filter is a processor that changes the timbre or tone of a sound by either blocking or passing a specific

frequency range. The parameters below determine the overall timbre of the sound by boosting or

cutting a certain frequency range. In addition to making the sound either brighter or mellower, Filter

can be used to produce electronic, synthesizer-like effects.

Brightness

Determines the cutoff frequency or effective

frequency range of the filter (see diagram).

Higher values result in a brighter sound.

Harmonic

Cont.

(Harmonic

Content)

Determines the emphasis given to the cutoff

frequency (resonance), set in Brightness

above (see diagram). Higher values result in

a more pronounced effect.

The EG (Envelope Generator) settings determine how the

level of the sound changes in time. This lets you reproduce

many sound characteristics of natural acoustic instruments

— such as the quick attack and decay of percussion sounds,

or the long release of a sustained piano tone.

Attack

Determines how quickly the sound reaches its maximum level after the key is played.

The lower the value, the quicker the attack.

Decay

Determines how quickly the sound reaches its sustain level (a slightly lower level than

maximum). The lower the value, the quicker the decay.

Release

Determines how quickly the sound decays to silence after the key is released. The

lower the value, the quicker the decay.

Vibrato

Vibrato is a quavering, vibrating sound effect that is

produced by regularly modulating the pitch of the Voice.

Depth

Determines the intensity of the Vibrato effect. Higher settings result in a more

pronounced Vibrato.

Speed

Determines the speed of the Vibrato effect.

Delay

Determines the amount of time that elapses between the playing of a key and the start

of the Vibrato effect. Higher settings increase the delay of the Vibrato onset.

Modulation

(+)/(-)

When the Modulation function is assigned to a pedal (page 44), the pedal can be used to modulate the

parameters below as well as the pitch (vibrato). Here, you can set the degree to which the pedal

modulates each of the following parameters.

Filter

Determines the degree to which the pedal modulates the Filter Cutoff Frequency. For

details about the filter, refer to page 49.

Volume

Cutoff Frequency

These frequencies are

“passed” by the filter.

Cutoff

range

Frequency

(pitch)

Frequency (pitch)

Volume

Resonance

Level

Attack Decay Release

Sustain

Level

Key-on Key-off

Time

Pitch

Speed

Delay

Depth

Time

Editing a Voice (Voice Edit)

CVP-809/CVP-805 Reference Manual

*Reverb and Chorus depth cannot be edited when a VRM Voice is selected, but can be edited via [Menu] → [VoiceSetting] → [Piano]

(page 1/2). For details, refer to page 79.

Determines the Frequency and Gain of the EQ bands. For information about EQ, refer to page 11.

From this display, you can set the same parameters as those in the Keyboard Harmony display (step 2 on page 24). Before

making any settings, make sure that the current part is set to Main; in other words, you should select the Main part by

touching the Voice name at the top of the Voice Edit display, or by pressing the VOICE [MAIN/LAYER/LEFT] button.

The settings here are called up automatically simply by selecting the corresponding Voice.

This section allows you to select the function to be assigned to the center or left pedal. Before making any settings, make

sure that the current part is set to Main; in other words, you should select the Main part by touching the Voice name at the

top of the Voice Edit display, or by pressing the VOICE [MAIN/LAYER/LEFT] button. The settings here are called up

automatically simply by selecting the corresponding Voice. For details about the pedal function, refer to page 44.

Modulation

(+)/(-)

Amplitude

Determines the degree to which the pedal modulates the amplitude (volume).

LFO Pitch

Determines the degree to which the pedal modulates the pitch, or the vibrato effect.

LFO Filter

Determines the degree to which the pedal modulates the Filter cutoff frequency, or the

wah effect.

LFO

Amplitude

Determines the degree to which the pedal modulates the amplitude, or the tremolo

effect.

Effect

Insertion

Effect

On/Off

Turns the Insertion Effects on or off.

Type

Selects the Insertion Effect Type. Select the Category then select the Type. You can

adjust the detailed parameters by touching (Setting) and save them. Refer to

“Editing and Saving the Effect settings” (page 13) for details.

Depth

Adjusts the Insertion Effect Depth.

Vibe Rotor

Available only if “VibeRotor” in the “Legacy” category is selected as the Insertion Effect

Type explained above. Determines whether Vibe Rotor should be set to on or off when

selecting the Voice.

Reverb* Depth

Adjusts the Reverb Depth.

Chorus* Depth

Adjusts the Chorus Depth.

Keyboard Harmony

Pedal

CVP-809/CVP-805 Reference Manual 51

Editing an Organ Flutes Voice (Voice Edit)

The Organ Flute Voices can be edited by adjusting the footage levers, adding the attack sound, applying effect and

equalizer, etc.

1 Select the desired Organ Flutes Voice.

From the [Organ] Category, touch [Organ Flutes], then select the desired Organ Flutes Voice.

2 On the Voice Edit display called up via [Menu] → [VoiceEdit], select the desired parameter

then edit the value.

NOTE The Voice Edit display for the Organ Flutes Voices can also be called up by touching the Organ Flutes icon at upper right

of the Organ Flutes Voice name in the Home display. This is useful for adjusting footage settings and controlling the rotary

speaker while you play.

There are three types for Organ Flutes Voices and the parameters indicated by “*” are available only for the Vintage

and Home type. For details about the organ types, refer to the Owner’s Manual, Chapter 3.

Vol um e

Adjusts the overall volume of the Organ Flutes.

Rotary/

Tremolo*

Alternately switches the Rotary Speaker speed between “Slow” and “Fast.” This

parameter is available only when an effect (page 12) which contains “Rotary” in its

name is applied.

Vibrato*

Turns on or off the vibrato, and adjusts its depth and speed.

Response

Affects both the attack and release (page 49) portion of the sound, increasing or

decreasing the response time of the initial swell and release, based on the Footage

controls. The higher the value, the slower the swell and release.

Attack

Selects “First” or “Each” as the Attack mode and adjusts the Attack length of the

sound.

In the First mode, attack (percussive sound) is applied only to the first notes played

and held simultaneously; while the first notes are held, any subsequently played

notes have no attack applied. In the Each mode, attack is applied equally to all notes.

The Attack length produces a longer or shorter decay immediately after the initial

attack. The longer the value, the longer the decay time.

Footage

Determines the basic sound of the organ flutes.

Editing an Organ Flutes Voice (Voice Edit)

CVP-809/CVP-805 Reference Manual

3 As necessary, touch (Setting) then set the parameters related to the Effects and EQ.

The parameters are same as those in the Effect display and EQ display of the previous chapter “Editing a Voice

(Voice Edit)” (page 50).

4 Touch (Save) to save the created Organ Flutes Voice.

NOTICE

The settings will be lost if you select another Voice or turn the power to the instrument off without executing the

Save operation.

NOTE If you want to edit another Voice, touch the Voice name at the top of the Voice Edit display. Or, press the VOICE [MAIN/

LAYER/LEFT] button to select the Keyboard part to which the desired Voice is assigned, confirm the Voice name at the

top of the Voice Edit display, make the edits as desired, then execute the Save operation.

CVP-809/CVP-805 Reference Manual 53

Creating/Editing Styles (Style Creator)

The Style Creator function lets you create an original Style by recording the rhythm pattern via the keyboard performance

and using the already-recorded Style data. Basically, select a preset Style that is closest to the type you want to create, then

record the rhythm pattern, bass line, chord backing, or phrase (referred to as “Source Pattern” in the Style Creator) for

each channel of each Section. Like the Song, two Recording methods are available: Realtime Recording and Step

Recording (page 54).

 Style Data Structure – Consisting of Source Patterns

A Style is made up of different Sections (Intro, Main, Ending, etc.) and each Section has eight separate channels, each of

which is referred to as a “Source Pattern.” With the Style Creator feature, you can create a Style by separately recording the

Source Pattern for each channel, or by importing pattern data from other existing Styles.

Main A

Main B

Fill In

Intro

Ending 2

Ending 3

Rhythm 1

Rhythm 2

Bass

Chord 1

Chord 2

Pad

Phrase 1

Phrase 2

Recording or copying from another Style

Creating a Source

Pattern for each channel

separately

Creating/Editing Styles (Style Creator)

CVP-809/CVP-805 Reference Manual

 Basic Procedure for creating a Style

The detailed instructions are described on the reference page of each step.

1 Select the desired Style as starting data.

2 Call up the Style Creator display via [Menu] → [StyleCreator].

3 On the “Basic” display, select a Section (page 55).

As necessary, make the following settings.

• If you create a Style entirely from scratch, touch [Initialize Style] to make the current Style empty.

• If you initialize the Style, set the length (measure amount) of the Source Pattern.

• Set the overall parameters such as Tempo and Beat.

4 Create the Source Pattern for each channel.

• Realtime Recording (page 56)

Lets you record the Style by simply playing the keyboard.

• Step Recording (page 59)

Lets you enter each note individually.

• Style Assembly (page 59)

Lets you copy various patterns from other preset Styles or Styles you have already created.

5 Edit the already recorded channel data.

• Channel Edit (page 60)

Lets you edit the MIDI data of the already recorded channels.

•SFF Edit (page 62)

Lets you edit the SFF (Style File Format) related parameters of the already recorded channels other than Rhythm

channels.

6 Repeat steps 3 – 5 as desired.

7 Touch (Save) at the top of the display to save the created Style.

Creating/Editing Styles (Style Creator)

CVP-809/CVP-805 Reference Manual

The explanations here apply to step 3 on page 54. This display lets you set the basic parameters such as Section selection.

Basic

Section

Selects a Section for creating or editing.

Pattern Length

Selects the length (in measures) of the current Section. After inputting the value, touch

[Execute] to actually enter the changes.

Te mp o

Sets the tempo of the Style. The setting here commonly applies to all Sections.

Beat

Sets the beat of the Style. The setting here commonly applies to all Sections. After inputting the

value, touch [Execute] to actually enter the changes.

Initialize Style

Initializes all channel data of all Sections belonging to make the current Style empty. Touch here

when you want to create the Style data from scratch.

Creating/Editing Styles (Style Creator)

CVP-809/CVP-805 Reference Manual

The explanations here apply to step 4 on page 54. In the “Rec Channel” display, you can create the channel data via the

Realtime Recording.

 Recording Rhythm Channels 1 – 2

1 On the “Rec Channel” display, touch and hold the desired channel until it turns red.

The selected channel becomes the Recording target whether the channel already contains data or not. If recorded

data is already included, you should record the additional notes to the selected channel as Overdub Recording.

2 If necessary, select a Voice then practice the rhythm pattern to be recorded.

Touch the instrument icon (illustration) to call up the Voice Selection display then select the desired Voice such as

Drum Kit. After selecting, touch [Close] to return to the original display. With the selected Voice, practice the

rhythm pattern to be recorded.

Realtime Recording

Realtime Recording Characteristics in the Style Creator

 Loop Recording

Style playback repeats the rhythm patterns of several measures in a “loop,” and Style recording is also done using

loops. For example, if you start recording with a two-measure Main section, the two measures are repeatedly

recorded. Notes that you record will play back from the next repetition (loop), letting you record while hearing

previously recorded material.

 Overdub Recording

This method records new material to a channel already containing recorded data, without deleting the original data.

In Style recording, the recorded data is not deleted, except when using functions such as “Clear Drum Inst” (page 57)

“Delete” (pages 57, 58) and “Remove Event” (page 61). For example, if you start recording with a two-measure Main

section, the two measures are repeated many times. Notes that you record will play back from the next repetition,

letting you overdub new material to the loop while hearing previously recorded material. When creating a Style

based on an existing internal Style, overdub recording is applied only to the rhythm channels. For all other channels

(except rhythm), you need to delete the original data before recording.

Available Voices for recording

For the Rhythm1 channel, any except Organ Flutes Voices can be used for recording.

For the Rhythm2 channel, only Drum/SFX kits can be used for recording.

Creating/Editing Styles (Style Creator)

CVP-809/CVP-805 Reference Manual

3 Press the STYLE CONTROL [ / ](START/STOP) button to start recording.

Since already recorded data plays back, turn each channel on or off by touching as desired.

If necessary, delete a channel by touching [Delete] located under the desired channel.

4 As soon as loop playback returns to the first beat in the first measure, start playing the

rhythm pattern to be recorded.

If the rhythm is difficult to play all at once, you can break it down into isolated parts, such as in this example:

If you make a mistake or play any wrong notes:

You can delete notes of a specific drum instrument. Touch [Clear Drum Inst] to call up a message, then press the

corresponding key on the keyboard while the message is shown. After deleting the desired drum instrument, touch

[Exit] to close the message.

5 Press the STYLE CONTROL [ / ](START/STOP) button to stop playback.

If you want to add more notes, press the [ / ] (START/STOP) button again to continue recording.

6 Touch and hold the Recording channel for a while (until the button changes color) to exit

from the Recording mode.

 Recording Bass, Chord 1 – 2, Pad and Phrase 1 – 2

1 On the “Rec Channel” display, touch and hold the desired channel until it turns red.

If the selected channel already contains data, a confirmation message appears, prompting you whether or not to

delete the existing data of the selected channel. Touch [Yes] to delete data and the selected channel is specified as

Record target. Note that channel data other than the Rhythm channels of the preset Style cannot be overdubbed.

2 If necessary, select a Voice then practice the bass line, chord backing, or phrase to be

recorded.

Touch the instrument icon (illustration) to call up the Voice Selection display then select the desired Voice. After

selecting, touch [Close] to return to the original display. With the selected Voice, practice the phrase or chord

backing to be recorded.

Loop 1st round

Bass Drum

Loop 2nd round

Snare Drum

Bass Drum

Loop 3rd round

Hi-Hat

Snare Drum

Bass Drum

Creating/Editing Styles (Style Creator)

CVP-809/CVP-805 Reference Manual

 Record a phrase in CM7 which will play appropriate notes as change chords during

performance

Rules when recording a Main or Fill-in

With the default initial settings, the Source Root/Chord is set to CM7. This means that you should record a Source

Pattern which is to be triggered by specifying CM7 during normal performance. Record a bass line, phrase or chord

backing which you want to hear when CM7 is specified. Specifically, see the rules below.

• Use only the CM7 scale tones when recording the Bass and Phrase channels (i.e., C, D, E, G, A, and B).

• Use only the chord tones when recording the Chord and Pad channels (i.e., C, E, G, and B).

If you observe these rules, Style playback notes are appropriately converted depending on the chord changes you

make during your performance.

Rules when recording an Intro or Ending

These Sections are designed assuming that the chord is not changed during playback. This is why you need not

observe the rules for Main and Fill-In Sections described above, and you can make the chord progression in

recording. However, follow the rules below since the Source Root/Chord is set to CM7 by default.

• When recording the Intro, make sure that the recorded phrase leads properly into a C scale.

• When recording the Ending, make sure that the recorded phrase begins with or properly follows a C scale.

 Setting the Source Root/Chord if necessary

Although the default Source Root/Chord is set to CM7 as described above, you can change this to any desired one in

which you can play easily. Call up the “SFF Edit” display, set the Source Root and Chord to the favorite or desired

Root and Chord type. Keep in mind that when you change the Source Chord from the default CM7 to another

chord, the chord notes and recommended notes will also change. For details, refer to page 63.

3 Press the STYLE CONTROL [ / ](START/STOP) button to start recording.

With the already recorded data playing back, turn each channel on or off by touching as desired.

If necessary, delete a channel by touching [Delete] located under the desired channel.

4 As soon as loop playback returns to the first beat in the first measure, start playing the bass

line, chord backing or phrase to be recorded.

5 Press the [ / ](START/STOP) button to stop playback.

If you want to add more notes, press the [ / ](START/STOP) button again to continue recording.

 To hear the playback sound of the already recorded channels with another Source Chord/

Root:

1) Call up the “SFF Edit” display, then set the “Target Ch” at the top of the display to “Rhythm1” or “Rhythm2.”

2) Touch [Play Root/Chord] to call up the operation display.

3) Press the STYLE CONTROL [ / ](START/STOP) button to start playback.

4) On the display, set the “Play Root/Chord” to the desired Chord root and Chord type.

This operation lets you hear how the Source Pattern is played back via chord changes during normal

performance.

6 Touch and hold the Recording channel for a while (until the button changes color) to exit

from the Recording mode.

Available Voices for recording

Any except for the Organ Flutes/Drum kit/SFX kit Voices can be used for recording.

C R C C R C

C = Chord note

C, R = Recommended note

Creating/Editing Styles (Style Creator)

CVP-809/CVP-805 Reference Manual

The explanations here apply to step 4 on page 54. In the Step Recording (Style Edit) display called up by touching

(Edit) at the upper right of the display, you can record or edit notes one by one. This Step Recording procedure is

essentially the same as that for Song Recording (page 67) with the exception of the points listed below:

• In the Song Creator, the “End” mark position can be changed freely; in the Style Creator, it cannot be changed. This is

because the length of the Style is fixed for all channels as you set in the “Basic” display (page 55). For example, if you

create a Style of four measures length, the “End” mark position is automatically set to the end of fourth measure, and

cannot be changed in the Style Edit display.

• Recording channels can be changed in the Song Creator’s Edit display; however, they cannot be changed in the Style

Creator. Select the Recording channel in the “Rec channel” display.

• In the Style Creator, Chord, Lyrics, and System Exclusive data cannot be entered. The Channel data can be entered and

System Exclusive data can be edited (delete, copy or move).

The explanations here apply to step 4 on page 54. The “Assembly” display shows that each channel data of the current

Section has been copied from which Style, which Section, and which channel. For each channel, touch the Style name,

Section name, or Channel name in the “Copy From” section as necessary to select the desired one. Assemble the Style

while listening to the Style playback by pressing the STYLE CONTROL [ / ] (START/STOP) button. You can turn

each channel on or off by touching the channel button.

Step Recording

Assembly — Assigning the Source Pattern to Each Channel

Creating/Editing Styles (Style Creator)

CVP-809/CVP-805 Reference Manual

The explanations here apply to step 5 on page 54. The “Channel Edit” display lets you edit the already recorded channel

data. Select the Target channel then edit the desired parameters.

After editing the desired parameter, touch [Execute] to actually enter the edits for each setup window. When execution is

completed, this button changes to [Undo], letting you restore the original data if you are not satisfied with the results. The

Undo function only has one level; only the previous operation can be undone.

Channel Edit

Target Ch

Select the target channel to be edited. All items with the exception of the “Groove” are to be applied

to the channel specified here.

Groove

This lets you add swing to the music or change the “feel” of the beat by making subtle shifts in the

timing (clock) of the Style. The Groove settings are applied to all channels of the selected Section.

Original Beat

Specifies the beats to which Groove timing is to be applied. In other words, if “8

Beat” is selected, Groove timing is applied to the 8th notes; if “12 Beat” is

selected, Groove timing is applied to 8th-note triplets.

Beat Converter

Actually changes the timing of the beats (specified in the “Original Beat”

parameter above) to the selected value. For example, when Original Beat is set

to “8 Beat” and Beat Converter is set to “12,” all 8th notes in the section are

shifted to 8th-note triplet timing. The “16A” and “16B” Beat Converter which

appear when Original Beat is set to “12 Beat” are variations on a basic 16th-

note setting.

Swing

Produces a “swing” feel by shifting the timing of the back beats, depending on

the “Original Beat” parameter above. For example, if the specified Original

Beat value is “8 Beat”, the Swing parameter will selectively delay the 2nd, 4th,

6th, and 8th beats of each measure to create a swing feel. The settings “A”

through “E” produce different degrees of swing, with “A” being the most subtle

and “E” being the most pronounced.

Fine

Selects a variety of Groove “templates” to be applied to the selected section. The

“Push” settings cause certain beats to be played early, while “Heavy” settings

delay the timing of certain beats. The numbered settings (2, 3, 4, 5) determine

which beats are to be affected. All beats up to the specified beat — but not

including the first beat — will be played early or delayed (for example, the 2nd

and 3rd beats, if “3” is selected). In all cases, “A” types produce minimum effect,

“B” types produce medium effect, and “C” types produce maximum effect.

Creating/Editing Styles (Style Creator)

CVP-809/CVP-805 Reference Manual

Dynamics

This changes the velocity/volume (or accent) of certain notes in the Style playback. The Dynamics

settings can be applied to each channel individually or all channels of the selected Style.

Accent Type

Determines the type of accent applied — in other words, which notes are

emphasized.

Strength

Determines how strongly the selected Accent Type (above) will be applied. The

higher the value, the stronger the effect.

Expand/

Compress

Expands or compresses the range of velocity values. Values higher than 100%

expand the dynamic range, while values lower than 100% compress it.

Boost/Cut

Boosts or cuts all velocity values. Values above 100% boost the overall velocity,

while values below 100% reduce it.

Apply To All

Channels

When set to “On,” the settings in this display will be applied to all the channels

of the current Section.

When set to “Off,” the settings in this display will be applied to the channel

specified at the “Target Ch” in the Channel Edit display.

Quantize

Same as in the Song Creator (page 76), with the exception of the two additional available parameters

below.

Eighth notes with swing

Sixteenth notes with swing

Vel oc ity

Boosts or cuts the velocity of all notes in the specified channel, according to the percentage specified

here.

Bar Copy

This function allows data to be copied from one measure or group of measures to another location

within the specified channel.

Source Top

Specifies the first (Source Top) and last (Source Last) measures in the region to

be copied.

Source Last

Destination

Specifies the first measure of the destination location, to which the data is to be

copied.

Bar Clear

This function clears all data from the specified range of measures within the selected channel.

Remove

Event

This function lets you remove specific events from the selected channel.

Creating/Editing Styles (Style Creator)

CVP-809/CVP-805 Reference Manual

The explanations here apply to step 5 on page 54. The Style File Format (SFF) combines all of Yamaha’s Style playback

know-how into a single unified format. Setting the SFF related parameters determines how the original notes are

converted to the actual sounded notes based on the chord you specify in the Chord area of the keyboard. The conversion

flow is shown below.

The parameters shown above can be set in the “SFF Edit” display.

SFF Edit — Making Style File Format Settings

Source Pattern settings

• Source Root

• Source Chord

Determines what key and what chord type are used for playing.

Note Conversion from the Source Pattern

• NTR (Conversion via the Chord Root change)....... page 63

• NTT (Conversion via the Chord Type change) ....... page 64

Octave Setting of the Converted Notes

• High Key (Upper octave limit of the Note Transposition)

• Note Limit (Note range between the highest and lowest notes)

Others

• RTR (How the note pitch changes in response to chord changes)

Set these parameters

before recording.

Set these parameters

after recording.

Actual Sounded Notes

Chord changes during normal performance

Creating/Editing Styles (Style Creator)

CVP-809/CVP-805 Reference Manual

Target Ch

Select the target channel to be edited.

Source Root/

Chord

(Play Root/

Chord)

These settings determine the original key of the Source Pattern (i.e., the key used when recording

the pattern to the channel other than the Rhythm channels). If you set “Fm7” here, specifying

“Fm7” in the Chord section of the keyboard will play back the originally recorded data (Source

Pattern). The default setting is “CM7” (Source Root = C and Source Chord = M7). Depending on

the selected chord type specified here, the playable notes (scale notes and chord notes) differ. When

“Initialize Style” is executed in the “Basic” display, the default setting of CM7 is automatically

selected.

IMPORTANT

Make sure to set the parameters here before recording. If you change the settings after recording,

the recorded Source Pattern cannot be converted to the appropriate notes when changing the

chord during your keyboard performance.

NOTE When the parameters for the selected Target Ch are set to NTR: Root Fixed, NTT Type: Bypass, or NTT

Bass: Off, the parameters here are changed to “Play Root” and “Play Chord,” respectively. In this case,

you can change chords and hear the resulting sound for all channels.

NOTE The settings here are not applied when NTR is set to “Guitar.”

NTR/NTT

(Note

Transposition

Rule/Note

Transposition

Tabl e)

The parameters here determine how the notes in the Source Pattern are converted according to the

chord changes during your keyboard performance.

NTR

Selects the Note Transposition Rule which determines how the notes in the Source

Pattern are transposed according to the Chord Root change.

Root Trans

When the root note is transposed, the interval between notes is

maintained. For example, the notes C3, E3 and G3 in the key of C

become F3, A3 and C4 when they are transposed to F. Use this setting for

channels that contain melody lines.

Root Fixed

The note is kept as close as possible to the previous note range. For

example, the notes C3, E3 and G3 in the key of C become C3, F3 and A3

when they are transposed to F. Use this setting for channels that contain

chord parts.

Guitar

This is exclusively for transposing guitar accompaniment. Notes are

transposed to approximate the chords played with natural guitar

fingering.

CR CR

CR CCR

CCR

RRCCC

ᅈ5

CC RC

(9)

CR CC

(11)

CR C CR

CmM

CC RC

Cm add9

CCC

CC RC C

CmM

(9)

CCR

Cdim

CR R RC

CCR

Cdim

CCC C

(9)

CRC

ᅈ5

CRC CR

ᅊ11

CCC

C sus

CRC CR

CMaj

CRC C CR

CCC C CR

(9)

CCC C RC

(9)

CRC

RCR

Caug

CRC C RC

CRC C CR

ᅊ11

CCC CR

Cadd9

CRC CC

(13)

CCC

(ᅈ9)

1+8

1+5

CCC

RCC

(ᅊ9)

CRC

RCC

C aug

CRC CRR

CM aug

CCCR

RCC

(ᅈ13)

CR CC

Csus

CCR CR

Csus

Playable notes when Source Root is C:

C = Chord notes

C, R = Recommended notes

When playing a

C major chord.

When playing an

F major chord.

When playing a

C major chord.

When playing an

F major chord.

Creating/Editing Styles (Style Creator)

CVP-809/CVP-805 Reference Manual

NTR/NTT

(Note

Transposition

Rule/Note

Transposition

Tabl e)

NTT

Type

Selects the Note Transposition Table which determines how the notes in the Source

Pattern are transposed according to the Chord Type change.

When NTR is set to “Root Trans” or “Root Fixed”:

Bypass

When NTR is set to Root Fixed, the transposition table used does not do

any note conversion. When NTR is set to Root Trans, the table used only

converts the notes by maintaining the pitch relationship between notes.

Melody

Suitable for melody line transposition. Use this for melody channels such

as “Phrase1” and “Phrase2.”

Chord

Suitable for chordal parts transposition. Use this for the “Chord1” and

“Chord2” channels, especially when they contain piano or guitar-like

chordal parts.

Melodic

Minor

When the played chord changes from a major to a minor chord, this table

lowers the third interval in the scale by a semitone. When the chord

changes from a minor to a major chord, the minor third interval is raised

by a semitone. Other notes are not changed. Use this for melody channels

of Sections which respond only to major/minor chords, such as Intros

and Endings.

Melodic

Minor 5th

In addition to the Melodic Minor transposition above, augmented and

diminished chords affect the 5th note of the Source Pattern.

Harmonic

Minor

When the played chord changes from a major to a minor chord, this table

lowers the third and sixth intervals in the scale by a semitone. When the

chord changes from a minor to a major chord, the minor third and flatted

sixth intervals are raised by a semitone. Other notes are not changed. Use

this for chord channels of Sections which respond only to major/minor

chords, such as Intros and Endings.

Harmonic

Minor 5th

In addition to the Harmonic Minor transposition above, augmented and

diminished chords affect the 5th note of the Source pattern.

Natural

Minor

When the played chord changes from a major to a minor chord, this

table lowers the third, sixth and seventh intervals in the scale by a

semitone. When the chord changes from a minor to a major chord, the

minor third, flatted sixth and flatted seventh intervals are raised by a

semitone. Other notes are not changed. Use this for chord channels of

Sections which respond only to a major/minor chord such as Intros and

Endings.

Natural

Minor 5th

In addition to the Natural Minor transposition above, augmented and

diminished chords affect the 5th note of the Source pattern.

Dorian

When the played chord changes from a major to a minor chord, this

table lowers the third and seventh intervals in the scale by a semitone.

When the chord changes from a minor to a major chord, the minor third

and flatted seventh intervals are raised by a semitone. Other notes are

not changed. Use this for chord channels of Sections which respond only

to a major/minor chord such as Intros and Endings.

Dorian 5th

In addition to the Dorian transposition above, augmented and

diminished chords affect the 5th note of the Source pattern.

When NTR is set to “Guitar”:

All Purpose

This table covers both strummed and arpeggio-played sounds.

Stroke

Suitable for strumming sounds of the guitar. Some notes may sound as if

they are muted—this is the normal condition when chords are played on

guitar by strumming.

Creating/Editing Styles (Style Creator)

CVP-809/CVP-805 Reference Manual

NTR/NTT

(Note

Transposition

Rule/Note

Transposition

Tabl e)

NTT

Type

Arpeggio

Suitable for arpeggio-played sound of the guitar, resulting in beautiful

four-note arpeggio sounds.

NTT

Bass

The channel for which this is set to “On” will be played back by the bass root note, when

the on-bass chord is recognized by the instrument. When NTR is set to Guitar and this

parameter is set to “On,” only the note which is assigned to bass will be played back by the

bass root note.

NTR/NTT Settings for the Rhythm Channels

Since the Rhythm channels should not be affected by Chord change, make sure to make the

following settings.

•

NTR = Root Fixed

• NTT = Bypass

• NTT Bass = Off

With the above settings, the “Source Root” and “Source Chord” parameters are changed to “Play

Root” and “Play Chord,” respectively.

High Key/Note

Limit

Adjusts the Octave of the notes converted via the NTT and NTR.

High Key

This sets the highest key (upper octave limit) of the note transposition

for the chord root change. Any notes calculated to be higher than the

highest key are transposed down to the next lowest octave. This setting is

available only when the NTR parameter (page 63) is set to “Root Trans.”

Note Limit Low

These set the note range (highest and lowest notes) for Voices recorded

to the Style channels. By judicious setting of this range, you can ensure

that the Voices sound as realistic as possible — in other words, that no

notes outside the natural range are sounded (e.g., high bass sounds or

low piccolo sounds).

Note Limit High

RTR

(Retrigger

Rule)

These settings determine whether notes stop sounding or not and how they change pitch in

response to chord changes.

Stop

The notes stop sounding.

Pitch Shift

The pitch of the note will bend without a new attack to match the type of

the new chord.

Pitch Shift to Root

The pitch of the note will bend without a new attack to match the root of

the new chord. However, the octave of the new note remains the same.

Retrigger

The note is retriggered with a new attack at a new pitch corresponding to

the next chord.

Retrigger To Root

The note is retriggered with a new attack at the root note of the next

chord. However, the octave of the new note remains the same.

Root changes

Notes played

Example — When the highest key is F

Root changes

Notes played

Example — When the lowest note is C3 and the highest is D4

High Limit

Low Limit

CVP-809/CVP-805 Reference Manual 66

Creating/Editing MIDI Songs (Song

Creator)

The Owner’s Manual covers how to create an original Song by recording your keyboard performance (see instructions of

Realtime Recording). This Reference Manual shows how to create an original Song by entering notes one by one

(instructions of the Step Recording) and how to improve the already created Song by editing the detailed parameters.

 Realtime Recording and Step Recording

When creating a Song, these two Recording methods are available. With Realtime Recording, this instrument records the

performance data as it is played. With Step Recording, you can compose your performance by “writing” it down one event

at a time. For instructions about the Realtime Recording, refer to the Owner’s Manual, Chapter 6. As the method of re-

recording a specific part of a Song in realtime, you can use the Punch In/Out function (page 89).

This chapter covers mainly the instructions of Step Recording.

 MIDI Song Data Structure

A MIDI Song consists of 16 MIDI channels. You can create data of a MIDI Song by recording your performance to a

specific channel or channels in realtime, or by executing Step Recording.

Song

Channel 1

Channel 2

Channel 3

Channel 4

Channel 5

Channel 6

Channel 7

Channel 8

Channel 9

Channel 10

Channel 11

Channel 12

Channel 13

Channel 14

Channel 15

Channel 16

System Exclusive

Lyrics

Recording Part

(default settings)

Main

Left

Layer

—

Rhythm 1

Rhythm 2

Bass

Chord 1

Chord 2

Pad

Phrase 1

Phrase 2

Keyboard Performance

• Realtime Recording:

By default, your keyboard performance will be

recorded to MIDI channels 1 – 3. You can also

record additional performances to channels 4 – 8.

•Step Recording:

Without specifying the keyboard part, you can

input the melodies or notes from sheet music one

by one to the desired channel.

Style Playback

• Realtime Recording:

By default, Style playback will be recorded to MIDI

channels 9 – 16.

•Step Recording:

After inputting the Chord change/Section change

events, touch [Expand] to actually record the note

data to MIDI channels 9 – 16.

Creating/Editing MIDI Songs (Song Creator)

CVP-809/CVP-805 Reference Manual

 Basic Procedure for creating a Song

This section covers the basic procedure for Step Recording.

1 Select the desired Song or create a new empty Song.

To create an empty Song, press the [ ] (REC) button, then touch [New MIDI] and [Cancel] in order.

2 Call up the Song Creator display via [Menu] → [SongCreator].

3 Touch (Edit) at the top of this display to call up the Song Edit display.

4 Touch [Ch1] at the top left of this display to select the Recording Target channel.

• If you want to record the keyboard performance, select one of “Ch1” – “Ch8.” If you do not intend to use Style playback

for the Song, “Ch9” – “Ch16” can be selected.

• If you want to edit the System Exclusive data, select “SysEx.”

• If you want to edit Lyrics, select “Lyrics.”

• If you want to record Style playback (Chord change and Section change events), select “Chord.”

5 According to selection in step 4, execute the Step Recording or data edits.

• When one of “Ch1” – “Ch16” is selected:

For instructions on editing already recorded data, refer to page 73.

For instructions on inputting melodies via Step Recording, touch [Step Rec] at the bottom left of the display then

refer to page 68.

• When “SysEx” is selected:

Edit the already recorded data, following the explanations on page 73. Step Recording is not available.

•When “Lyrics” is selected:

Edit the already recorded data, following the explanations on page 73. Step Recording is not available.

• When “Chord” is selected:

For instructions on editing already recorded data, refer to page 73.

For instructions on inputting Chord/Section Change events for Style playback via Step Recording, touch [Step

Rec] then refer to page 71.

6 If necessary, touch (Edit) to return to the portal display of the Song Creator, then

execute the Channel Edit function (page 76).

7 Touch (Save) at the top right of the display to save the created Song.

NOTICE

The recorded Song data will be lost if you select another Song or turn off the power to the instrument without

executing the Save operation.

3, 6 7

Creating/Editing MIDI Songs (Song Creator)

CVP-809/CVP-805 Reference Manual

The explanations here apply when one of “Ch1” – “Ch16” is selected in step 5 on page 67. With [Step Rec] turned on at the

bottom left of the display, you can input the notes one by one, using the controls below.

 Control Names and Functions

Recording Melodies via Step Recording

Event List

Indicates events such as note and Voice selection which have been input. For details,

refer to page 74.

Song Position

(Measure: Beat:

Clock)

Indicates the current Song position. Events such as note and Voice selection you have

input are recorded at the position indicated here. You can change the current position

by touching [ ] or [ ] below the Measure, Beat, and Clock* respectively.

*Clock

Smallest unit for the Song position and note length. A quarter note consists of 1920 clocks.

Cursor

Lets you move the cursor position.

Step Rec

Turning this on shows the Step Recording display, and turning it off shows the Song

Edit display.

Vel oc ity

Determines the velocity (loudness) of the note to be entered. The velocity value can be

specified within a range from 1 to 127. The higher the velocity value, the louder the

sound becomes.

Kbd.Vel: Actual resulting velocity

Length

Determines the gate time (note length) of the note to be entered.

Manual: For freely setting the gate time. Touch “Manual” and close the pop-up window by touching

“OK,” then set the gate time to any desired percentage by using the Data dial.

127

111

80% 40%

99%

20%

Normal: Staccato:

Tenu to : Sta c ca t is si m o:

Creating/Editing MIDI Songs (Song Creator)

CVP-809/CVP-805 Reference Manual

 Example of Step Recording — Melodies

• The numbers shown in the illustration correspond to the following operation step numbers.

• The illustration given here is just a sample. Since the music score (called up via [Menu] → [Score]) is generated from recorded MIDI

data, it may not appear exactly the same as shown above. Non-note musical performance symbols will not be shown in the Score

display, even if you’ve entered them.

This section describes the instructions on inputting the melodies of the above notation via the Step Recording. Before

starting, note the following points:

• To input the note with the tie in step 4, you need to operate without releasing the key. Proceed with the operations,

reading the instructions carefully.

• Before inputting notes as described below, select the desired Voice by using the Voice buttons. Even if it has already

been selected, you need to re-select the same Voice to input the Voice number to the Event List. Keep in mind that only

note and Voice selection events can be input with Step Recording.

1 Enter the first and second notes with a slur.

1-1 Touch [Velocity] to select “ .”

1-2 Touch [Length] to select “99% (Tenuto).”

1-3 Touch [Note Type] once or twice to call up the dotted note type.

1-4 Touch the dotted quarter-note length ( ) to turn it on.

1-5 Press the C3 key.

With the operations above, the first note has been entered. Next, enter the second note.

1-6 Touch [Note Type] once or twice to call up the normal note indications.

1-7 Touch the eighth-note length ( ) to turn it on.

1-8 Press the D3 key.

The first and second notes are entered with a slur.

2 Enter the next notes with staccato.

2-1 Touch [Length] to select “40% (Staccato).”

2-2 Touch the quarter-note length ( ) to turn it on.

2-3 Play the keys E3 and F3 in order.

The first measure has been completed.

Note Type, Note

Indication

Touching [Note Type] repeatedly will alternate the type of the note indications at right

in order: normal, dotted, and triplet. Select one of three types, then select (turn on)

one of the note indications with which the next note is input. If you touch the selected

note indication (which is turned on) again, a rest will be input with the corresponding

length.

Delete

Deletes the selected data.

1234

Creating/Editing MIDI Songs (Song Creator)

CVP-809/CVP-805 Reference Manual

3 Enter a quarter-note rest.

Touch the quarter-note ( ), that has been turned on, just once to input a quarter-note rest.

Be careful not to touch the same note (which is turned on) several times. Doing so results in multiple rest being

input for the corresponding times. Rests are not actually indicated as such in the Event List, but you can confirm

whether any have been input or not by checking the Song Position.

4 Enter the next notes and apply a tie.

4-1 Touch [Velocity] to select “ .”

4-2 Touch [Length] to select “80% (Normal).”

4-3 While holding G3 key on the keyboard, touch quarter-note ( ).

Do not release the G3 key yet. Keep holding it while executing the following steps.

4-4 While holding the G3 key, press the C4 key.

Do not release the G3 and C4 keys yet. Keep holding the notes while executing the following step.

4-5 While holding the keys G3 and C4, touch half-note ( ).

After touching half-note ( ), release the keys.

The second measure has been completed.

5 Press the SONG CONTROL [ ](STOP) button to return to the top of the Song, then hear

the newly entered Song by pressing the [ / ](PLAY/PAUSE) button.

Creating/Editing MIDI Songs (Song Creator)

CVP-809/CVP-805 Reference Manual

The explanations here apply when “Chord” is selected in step 5 on page 67. With [Step Rec] turned on at the bottom left of

the display, you can input the Chord/Section Change events for Style playback one by one.

 Control Names and Functions

Recording Chord/Section Change Events via Step Recording

Event List

Indicates events such as Chord and Section changes which have been input.

For details, refer to page 74.

Song Position

(Measure: Beat:

Clock)

Indicates the current Song position. Events such as Chord and Section change you

have input are recorded at the position indicated here. You can change the current

position by touching [ ] or [ ] below the Measure, Beat, and Clock* indications

respectively.

*Clock

Smallest unit for the Song position and note length. A quarter note consists of 1920 clocks.

Cursor

Lets you move the cursor position.

Step Rec

Turning this on shows the Step Recording display, and turning it off shows the Song

Edit display.

Note Indications

Select one of the four note lengths for inputting the next event.

Delete

Deletes the selected data.

Creating/Editing MIDI Songs (Song Creator)

CVP-809/CVP-805 Reference Manual

 Example of Step Recording — Chord/Section Events

These instructions show how to input the Chord/Section change events of the above notation via Step Recording. Before

starting, note the following points:

• Turn off the STYLE CONTROL [AUTO FILL IN] button on the panel.

• Select a conventional 4-beat Style.

NOTE In order to detect the chord played in the chord section of the keyboard, set the Fingering type (page 6) to a setting other than

“Full Keyboard” and “AI Full Keyboard.” Also, you need to set the “Stop ACMP” parameter to a setting other than “Disabled” in

the Style Setting display (page 84).

1 Enter the chords for the Main A section.

1-1 Press the MAIN VARIATION [A] button.

1-2 Touch the half-note length ( ) to turn it on.

1-3 Play the chords C, F and G in the chord section of the keyboard.

2 Enter the chords for the Break section.

2-1 Press the [BREAK] button.

2-2 Touch the quarter-note length ( ) to turn it on.

2-3 Play the chords F and G7 in the chord section of the keyboard.

NOTE To enter fill-ins, turn the [AUTO FILL IN] button to on, and simply press the desired MAIN VARIATION [A] – [D] button.

C F G F G7 C

123

Main A Main BBreak

* The numbers shown in the illustration correspond to the following operation step numbers.

1-1

1-3

1-2

2-2

2-3

2-1

Creating/Editing MIDI Songs (Song Creator)

CVP-809/CVP-805 Reference Manual

3 Enter the chords for the Main B section.

3-1 Press the MAIN VARIATION [B] button.

3-2 Touch the whole-note length ( ) to turn it on.

3-3 Play the chord C in the chord section of the keyboard.

The Chord and Section change events are now entered.

4 Press the SONG CONTROL [ ](STOP) button to return to the top of the Song, then listen

to the newly entered Song by pressing the [ / ](PLAY/PAUSE) button.

5 Touch and turn off [Step Rec] to call up the Song Edit display.

6 Touch [Expand] at the upper left of the Song Edit display to convert the Chord/Section

change events to the Song data.

With the operations above (steps 1 – 3), only Chord and Section change events are recorded, meaning that the

actual Song data has not been created and the Style part can produce no sound even if you start Song playback after

exiting from the Song Creator. Accordingly, make sure to execute the Expand function after you finish inputting. If

you have not finished inputting, save the Song to maintain the recorded events then continue inputting additional

events as desired in the future.

The explanations here apply to step 5 on page 67. From the Song Edit display, you can edit each of the events such as Note

data and Voice selection which are created via Realtime Recording or Step Recording.

Editing the Recorded Data

3-1

3-2

3-3

Creating/Editing MIDI Songs (Song Creator)

CVP-809/CVP-805 Reference Manual

Editing Target

Specifies the Editing Target.

• Ch 1 – Ch 16:

When one of these is selected, you can edit the channel data.

•SysEx: Lets you edit System Exclusive data which applies to all channels.

•Lyrics: Lets you edit Lyrics data.

•Chord: Lets you edit Chord/Section change events for Style playback.

Expand

This is shown only when “Chord” is selected above, and lets you convert the Chord/

Section change events you input in the Step Recording display to actual sounded note data.

Make sure to execute this function when finalizing Song data. If you exit from the Song

Creator without executing this function, starting Song playback produces no sound of the

Style part.

Event List

In this area, the events of the Song data are listed and can be edited. Each line shows one

event.

Depending on the Editing Target above ( ), the listed and editable events differ as

described below.

 When the Editing Target is set to one of “Ch1” – “Ch16”:

Note

An individual note within a Song. Includes the note name which

corresponds to the key which was played, plus a velocity value

based on how hard the key is played, and the gate time value (the

length of a note).

Ctrl

(Control Change)

Settings to control the Voice, such as volume, pan, filter and effect

depth (edited via the Mixer), etc.

Prog

(Program Change)

MIDI program change number for selecting a Voice.

P. B n d

(Pitch Bend)

Data for changing the pitch of a Voice continuously.

A.T.

(Aftertouch)

This event is generated when pressure is applied to a key after the

key is pressed. Note that the keyboard of this instrument does not

feature Aftertouch, although Aftertouch values can be entered

here.

 When the Editing Target is set to “SysEx”:

ScBar

(Score Start Bar)

Determines the top measure number as the starting point of the

Song data.

Te mp o

Determines the tempo value.

Time

(Time signature)

Determines the time signature

Key

(Key signature)

Determines the key signature, as well as the major/minor setting,

for the music score shown on the display.

XGPrm

(XG parameters)

Allows you to make various detailed changes to the XG

parameters. For details, refer to “MIDI Data Format” in the Data

List (separate PDF).

Indicates the Song position

(measure: beat: clock) of the

corresponding event.

Indicates the

event type.

Indicates the event value or detail.

Creating/Editing MIDI Songs (Song Creator)

CVP-809/CVP-805 Reference Manual

Event List Sys/Ex.

(System Exclusive)

Displays the System Exclusive data in the Song. Keep in mind that

you cannot create new data or change the contents of the data

here; however, you can delete, cut, copy, and paste the data.

Meta

(Meta event)

Displays the SMF meta events in the Song. Keep in mind that you

cannot create new data or change the contents of the data here;

however, you can delete, cut, copy, and paste the data.

 When the Editing Target is set to “Lyrics”:

Name

Allows you to enter the Song name.

Lyrics

Allows you to enter lyrics.

Code

CR:

Enters a line break in the lyrics text.

LF: Clears the currently displayed lyrics and displays the next set

of lyrics.

 When the Editing Target is set to “Chord”:

Style

Style name

Te mp o

Tempo setting

Chord

Chord root, Chord type, On Bass Chord

Sect (Section)

Style Section (Intro, Main, Fill In, Break, Ending)

OnOff

On/off status for each part (channel) of the Style

CH.Vol

(Channel Volume)

Volume for each part (channel) of the Style

S.Vol

(Style volume)

Overall volume of the Style

Song Position

(Measure: Beat:

Clock)

Indicates the current Song position. The events you input are recorded at the position

indicated here. You can change the current position by touching [ ] or [ ] below the

Measure, Beat, and Clock* indications respectively.

*Clock

Smallest unit for the Song position and note length. A quarter note consists of 1920 clocks.

Cursor

Lets you move the cursor position.

Step Rec

Turning this on shows the Step Recording display, and turning it off shows the Song Edit

display.

Event Filter

Calls up the Event Filter window, letting you select only the events you wish to be shown in

the event list.

: Checkmark all items.

: Remove checkmarks from all items.

: Invert checked/unchecked for all items.

Multi Select

After turning this on, use the Cursor buttons ( ) on the display to select multiple events.

Cut/Copy/Paste

Use these when you want to copy or move the selected events.

Insert

Adds a new event.

Delete

Deletes the selected events.

Cancel

Cancels editing and restores the original value.

-/+

Increases or decreases the value of the current cursor position by 1.

Creating/Editing MIDI Songs (Song Creator)

CVP-809/CVP-805 Reference Manual

The explanations here apply to step 6 on page 67. The Channel Edit display lets you correct or convert the specific portion

of the Song data.

After editing the desired parameter, touch [Execute] to actually enter the edits for each setup window. When execution is

completed, this button changes to [Undo], letting you restore the original data if you are not satisfied with the results. The

Undo function only has one level; only the previous operation can be undone.

Channel Edit — Editing Channel Data

Target Ch

Select the target channel to be edited.

Quantize

The Quantize function allows you to align the timing of all the notes in a channel. For example, if

you record the musical phrase shown below, you may not play it with absolute precision, and your

performance may have been slightly ahead of or behind the precise timing. Quantize is a convenient

way of correcting for this.

Size

Selects the quantize size (resolution). For optimum results, you should set the

Quantize size to the shortest note value in the channel. For example, if eighth notes

are the shortest in the channel, you should use eighth note as the Quantize size.

Settings:

The three Quantize settings marked with asterisks (*) are exceptionally

convenient, since they allow you to quantize two different note values at the same

time. For example, when the straight eighth notes and eighth notes triplet are

contained in the same channel, if you quantize by the straight eighth notes, all

notes in the channel are quantized to straight eighth notes — completely

eliminating any triplet feel. However, if you use the eighth note + eighth note

triplet setting, both the straight and triplet notes will be quantized correctly.

After 1/8 note quantization

1/4 note

triplet

1/8 note 1/16 note 1/32 note 1/16 note+

1/8 note triplet*

1/8 note

triplet

1/16 note

triplet

1/8 note+

1/8 note triplet*

1/16 note+

1/16 note triplet*

Creating/Editing MIDI Songs (Song Creator)

CVP-809/CVP-805 Reference Manual

Quantize Strength

Determines how strongly the notes will be quantized. A setting of 100% produces

exact timing. If a value less than 100% is selected, notes will be moved toward the

specified quantization beats according to the specified percentage. Applying less

than 100% quantization lets you preserve some of the “human” feel in the

recording.

Delete

You can delete the data of the specified channel in the Song. Checkmark (touch) the desired channel

whose data you wish to delete, then touch [Execute] to actually delete the data.

Mix

This function lets you mix the data of two channels and place the results in a different channel. It also

lets you copy the data from one channel to another.

Source 1 Ch

Determines the MIDI channel (1 – 16) to be mixed. All MIDI events of the channel

specified here are copied to the destination channel.

Source 2 Ch

Determines the MIDI channel (1 – 16) to be mixed. Only note events of the

channel specified here are copied to the destination channel. Besides the values 1 –

16, there is a “Copy” setting that allows you to copy the data from Source 1 to the

destination channel.

Destination

Determines the channel into which the mix or copy results will be placed.

Transpose

This allows you to transpose the recorded data of individual channels up or down by a maximum of

two octaves in semitone increments.

1-16

Sets the Transpose value for each channel.

All -

Decreases the Transpose value for all channels by 1.

All +

Increases the Transpose value for all channels by 1.

NOTE Make sure not to transpose channels 9 and 10. In general, Drum kits are assigned to these channels. If

you transpose the channels of Drum kits, the instruments assigned to each key will be changed.

Setup

The current settings of the Mixer display and other panel settings can be recorded to the top position

of the Song as the Setup data. The Mixer and panel settings recorded here are automatically recalled

when the Song starts.

Checkmark the items of playback features and functions that you wish to automatically be called up

along with the selected Song.

NOTE Before executing the Setup operation, move the Song position to the top of the Song by pressing the

SONG [STOP] button.

Original data (assuming 4/4 meter)

Quantizing strength = 100%

Quantizing strength = 50%

Quarter-note length

CVP-809/CVP-805 Reference Manual 78

Voice Settings

Lets you adjust the pitch related parameters for each keyboard part.

Tune

Tun ing

Determines the pitch of each keyboard part.

Octave

Determines the range of the pitch change in octaves, over two octaves up or down for each keyboard

part.

Pitch Bend

Range

Determines the range of the Pitch Bend for each keyboard part in semitones when the “Pitch Bend”

or “Glide” function is assigned to a pedal (page 44).

Portamento

Time

Portamento is a function that creates a smooth transition in pitch from the first note played on the

keyboard to the next. The Portamento Time determines the pitch transition time. Higher values

result in a longer pitch change time. Setting this to “0” results in no effect. This parameter is available

for keyboard parts which are set to “Mono” (page 48).

Voice Settings

CVP-809/CVP-805 Reference Manual

Lets you set the parameters for the “VRM Piano” category Voices.

*These settings are applied commonly to all parts for which VRM Voices are selected.

Piano

VRM* VRM

Turns the VRM effect on or off.

Damper Resonance Depth

Adjusts the depth of the VRM effect heard when pressing the damper pedal.

String Resonance Depth

Adjusts the depth of the VRM effect heard when playing the keyboard.

Reverb Depth

Adjusts the Reverb depth for VRM Voices.

Chorus Depth

Adjusts the Chorus depth for VRM Voices.

Key Off Sampling

Adjusts the volume of the key-off sound (the subtle sound that occurs when

you release a key). This is not applied to the “Concert Upright” Voice.

Voice Settings

CVP-809/CVP-805 Reference Manual

Lets you adjust the pitch and volume of each note (or key) individually for the “VRM Piano” category Voice selected as the

Main part.

Each Key Setting

Determines whether you set the pitch (Tune) or the volume is to be set.

Selects the note for changing the pitch or volume. When setting the pitch, you can select the note also by

pressing the actual key while holding down the keyboard illustration on the display.

Sets the pitch or the volume. The note for which the setting is changed from the default is colored in the

keyboard illustration on the display.

Resets all [Tune] or [Volume] settings to the default.

The VRM Piano Voice

selected for the Main

part.

Voice Settings

CVP-809/CVP-805 Reference Manual

Each Voice is linked to its default Voice Set parameter settings, equivalent to those in the Voice Edit display (page 47) for

the Voices other than the Organ Flutes Voices. Although usually these settings are automatically called up by selecting a

Voice, you can also disable this feature. For example, if you want to change the Voice yet keep the same Harmony effect,

remove the checkmark of “Keyboard Harmony.”

In the Voice Selection display, icons defining the Voice characteristics are indicated at the left of the Voice name. For some

particular Voices, (Information) is shown at the bottom of the display and detailed information can be called up by

touching it.

Voice Set

Other Setting

Category Button

Determines how the Voice Selection display is opened when one of the VOICE

category buttons is pressed.

•Open & Select:

Opens the Voice Selection display with the previously selected Voice

in the Voice category automatically selected (when one of the VOICE category

buttons is pressed).

•Open Only: Opens the Voice Selection display with the currently selected Voice

(when one of the VOICE category buttons is pressed).

S.Art2 Auto Articulation

(only for CVP-809)

Determines whether articulation is added to S.Art2 Voices automatically for these

respective key timings:

•Head:

When the first key is pressed.

•Joint: When the key is pressed or released while holding down other key(s).

•Tail: When the last key is released.

NOTE This affects not only S.Art2 Voices of your keyboard performance, but also the S.Art2

Voices in Songs or Styles.

Voice Characteristics

VRM

Refer to the Owner’s Manual, Chapter 3.

Natural!

Natural! Voices are high quality sounds based on many specialist sampling techniques.

They are especially suited to recreating Piano and other keyboard instruments.

Voice Settings

CVP-809/CVP-805 Reference Manual

S.Articulation!

S.Articulation2!

(only for CVP-809)

Refer to the Owner’s Manual, Chapter 3.

Live!

Live! Voices feature stereo sampling, to reproduce accurately the stereo image of an

acoustic instrument, as well as the ambience of the room it was recorded in.

Cool!

Cool! Voices reproduce the complex characteristics of Electric Instruments, by

utilizing sophisticated programming techniques in both voicing, and the use of DSP

effects.

Sweet!

Sweet! Voices are acoustic instruments which feature the sampled vibrato of the

original player, creating a far more realistic and emotional performance than

synthesized vibrato.

Drums

Drum & Percussion instruments are mapped across the keyboard so you can play

them directly, or use in music production. For information about what sound is

assigned to each key, refer to the “Drum/key Assignment List” in the Data List

(separate PDF).

Live!Drums

Stereo sampling is used for these high definition Drum and Percussion instruments,

which are mapped across the keyboard so you can play them directly, or use in music

production.

Revo!Drums

(only for CVP-809)

These Voices recreate the natural sound of real drums by producing different

instrument sound samples (or waveforms), when playing the same key multiple times.

SFX

Special percussion and sound effects are mapped across the keyboard, so you can play

them directly, or use in music production. For information about what sound is

assigned to each key, refer to the “Drum/key Assignment List” in the Data List

(separate PDF).

Live!SFX

Stereo sampling is used for these high definition special percussion and sound effects,

which are mapped across the keyboard so you can play them directly, or use in music

production.

Revo!SFX

(only for CVP-809)

These Voices recreate the natural sound of real percussion instruments by producing

different sound samples (or waveforms), when playing the same key multiple times.

OrganFlutes!

OrganFlutes! lets you create your own Organ registrations, by combining Organ Flute

Footages at different pitches, just like a real organ. See page 51 for details.

MegaVoice

MegaVoice is a special Voice format designed for use in styles and songs, not for live

performance. Different velocity ranges are used to select dramatically different playing

styles simultaneously, and without changing the voice.

Actual sound maps for the MegaVoices are given in the Data List (separate PDF).

NOTE MegaVoices are not compatible with other models. Any Song or Style data you’ve

created on this instrument using the MegaVoices will not sound properly when played

back on other instruments which do not feature the same MegaVoices.

NOTE MegaVoices will sound differently depending on the keyboard range, velocity, touch,

etc. Hence, if you apply the Keyboard Harmony effect, change the transpose setting or

change the Voice Set parameters, unexpected or undesired sounds may result.

Regular

Other Voices including GM Voices and XG Voices.

Voice Settings

CVP-809/CVP-805 Reference Manual

This instrument features GM Voices, XG Voices, and MegaVoices. These Voices can be called up from the “Others”

category in the Voice Selection display.

1 From the Home display, touch the Voice name of the desired part to call up the Voice

Selection display.

2 Touch the tab of the “Others” category.

3 Touch (Above) several times if necessary, to call up the root directory of “Others.”

4 Touch the desired category, such as “GM&XG” and “MegaVoice.”

NOTE You can find the “Legacy” folder in this display. This folder contains previous Yamaha Clavinova Voices (such as CVP-

709, 705 etc.) for data compatibility with other models.

5 Select the desired Voice.

Selecting GM/XG or MegaVoices

CVP-809/CVP-805 Reference Manual 84

Style Playback Related Settings

Setting

Dynamics Control

•Off: The Style volume does not respond to your playing strength.

•Narrow: The Style volume changes over a narrow range in response to your playing

strength. In other words, you must play very strongly or softly to have the volume

change.

•Medium: The Style volume changes normally in response to your playing strength.

•Wide: The Style volume changes over a wide range in response to your playing strength.

In other words, playing strongly or softly produces greater changes in the volume.

Display Tempo

Turns on or off the tempo indication for each Style on the Style Selection display.

Stop ACMP

When the [ACMP ON/OFF] button is on, [SYNC START] is off, and this parameter is

set to the value other than “Disabled,” you can play chords in the chord section of the

keyboard with the Style stopped, and still hear the accompaniment chord. In this

condition — called “Stop Accompaniment” — any valid chord fingerings are

recognized and the chord root/type are shown in the Style area of the Home display.

Here, you can determine whether the chord played in the chord section will sound or

not in the Stop Accompaniment status.

•Disabled:

Disables the Stop Accompaniment feature. When Style playback is stopped,

any pressed notes in the chord section of the keyboard will not be recognized as chords.

•Off: The chord played in the chord section will not sound.

•Style: The chord played in the chord section will sound via the Voices for the Pad part

and the Bass channel of the selected Style.

•Fixed: The chord played in the chord section will sound via the specified Voice,

regardless of the selected Style.

NOTE When the selected Style contains MegaVoices, unexpected sounds may result when this

is set to “Style.”

NOTE If you record a Song using the Stop Accompaniment, both the Voice that is sounded and

the chord data will be recorded when set to “Style,” and only the chord data will be

recorded when set to “Off” or “Fixed.”

NOTE When this is set to “Disabled,” chords are not recognized while the Style is stopped. This

is why both Vocal Harmony (with the Chordal mode) and Keyboard Harmony are not

applied even if you play a chord in the chord section of the keyboard while the Style is

stopped.

Style Playback Related Settings

CVP-809/CVP-805 Reference Manual

ACMP On/Off Default

Determines whether the [ACMP ON/OFF] button is on or off when the power is

turned on.

OTS Link Timing

This applies to the OTS Link function. This parameter determines the timing in which

the One Touch Settings change with the MAIN VARIATION [A] – [D] change. (The

[OTS LINK] button must be on.)

•Real Time:

One Touch Setting is immediately called up when you press a MAIN

VARIATION button.

•Next Bar: One Touch Setting is called up at the next measure, after you press a MAIN

VARIATION button.

Synchro Stop Window

This determines how long you can hold a chord before the Synchro Stop function is

automatically cancelled. When the [SYNC STOP] button is turned on and this is set to

a value other than “Off,” the Synchro Stop function is automatically cancelled if you

hold a chord for longer than the time set here. This conveniently resets Style playback

control to normal, letting you release the keys and still have the Style play. In other

words, if you release the keys sooner than the time set here, the Synchro Stop function

works.

Change Behavior

Section Set

Determines the default section that is automatically called up when selecting different

Styles (when Style playback is stopped). When set to “Off” and Style playback is

stopped, the active section is maintained even if the different Style is selected. When

any of the MAIN A–D sections is not included in the Style data, the nearest Section is

automatically selected. For example, when MAIN D is not contained in the selected

Style, MAIN C will be called up.

Te mp o

This determines whether the tempo changes or not when you change the Style.

•Lock:

Regardless of playback status, the tempo setting of the previous Style is

maintained.

•Hold: While the Style is playing back, the tempo setting of the previous Style is

maintained. While the Style is stopped, the tempo changes to that of the default tempo of

the selected Style.

•Reset: Regardless of playback status, the tempo changes to that of the default tempo for

the selected Style.

Part On/Off

This determines whether the Style Channel on/off status changes or not when you

change the Style.

•Lock:

Regardless of playback status, the Channel on/off status of the previous Style is

maintained.

•Hold: While the Style is playing back, the Channel on/off status of the previous Style is

maintained. While the Style is stopping, all Channels of the selected Style are set to on.

•Reset: Regardless of playback status, all Channels of the selected Style are set to on.

Style Playback Related Settings

CVP-809/CVP-805 Reference Manual

Style Characteristics

On the Style Selection display, icons defining the Style characteristics are indicated at left of the Style name.

•

Pro: These Styles provide professional and exciting arrangements combined with perfect playability. The resulting

accompaniment exactly follows the chords of the player. As a result, your chord changes and colorful harmonies

are instantly transformed into lifelike musical accompaniment.

•

Session: These Styles provide even greater realism and authentic backing by mixing in original chord types and

changes, as well as special riffs with chord changes, with the Main sections. These have been programmed to add

“spice” and a professional touch to your performances of certain songs and in certain genres. Keep in mind,

however, that the Styles may not necessarily be appropriate or even harmonically correct for all songs and for all

chord playing. In some cases for example, playing a simple major triad for a country song may result in a “jazzy”

seventh chord, or playing an on-bass chord may result in inappropriate or unexpected accompaniment.

•

Free Play: These Styles are characterized by rubato performance. You can perform freely with remarkably

expressive accompaniment without being constrained by a strict tempo.

•

Pianist: These special Styles provide piano-only accompaniment. Just by playing the proper chords with your left

hand, you can automatically add complicated, professional-sounding arpeggios and bass/chord patterns.

CVP-809/CVP-805 Reference Manual 87

Song Settings Related to Playback/Recording

If you turn on the Guide function and play back a MIDI Song, the keyboard guide lamps indicate the notes (location and

timing) for you to play. Also, when you sing along with Song playback, you can control the playback timing by playing the

keyboard to match your singing.

The Guide function can be turned on from the Song area (when expanded) of the Home display, Score display, Lyrics

display and Text display. For instructions on how to use Guide function, refer to the Owner’s Manual, Chapter 5. This

section covers the detailed parameters about the Guide function.

NOTE The Guide settings can be saved as a part of Song data (page 77). When you select the saved Song the next time, the

corresponding Guide settings will also be called up.

Guide

Type

Lets you select the Guide type.

 Guide menu for keyboard practice

•Follow Lights: With this function, the keyboard guide lamps indicate which notes you should play.

Song playback pauses and waits for you to play. When you play the correct notes, Song playback

continues.

•Any Key: With this function, you can play the melody of a Song just by pressing a single key (any key is

OK) in time with the rhythm. Song playback pauses and waits for you to play any key. Simply play a key

on the keyboard in time with the music and Song playback continues.

•Your Tempo: Basically the same as “Follow Lights.” In addition, playback tempo will change to match

the speed at which you are playing.

 Guide menu for singing

•Karao-Key: This function lets you control the Song playback timing with just one finger, while you

sing along. This is useful for singing along with your own performance. Song playback pauses, waiting

for you to sing. Simply play any key on the keyboard (playing the keyboard produces no sound) and

Song playback continues.

Lamp

Activates or deactivates the keyboard guide lamp.

NOTE If the Guide Lamps do not light as intended in the “Part Ch” display, set the Right to “Ch1” then set the

Left to “Ch2.”

Lamp

Timing

Determines the timing by which the keyboard guide lamps light.

•Just:

The guide lamps light in time with the music, at the same timing you should play.

•Next: The guide lamps light slightly ahead of the music, indicating the notes you should play next. The

guide lamps flash if you fail to play the keys with the correct timing.

Song Settings Related to Playback/Recording

CVP-809/CVP-805 Reference Manual

Part Ch

Right

Determines which channel is assigned to the right-hand part.

Left

Determines which channel is assigned to the left-hand part.

Auto Set

When set to “On,” this automatically sets the proper MIDI channels for the right- and left hand parts

pre-programmed in the commercially available Song data. Normally, this should be set to “On.”

Lyrics

Language

Determines the language of the displayed lyrics.

•Auto:

When the language is specified in the Song data, the lyrics are displayed accordingly. When the

language is not specified in the Song data, the lyrics language is regarded as “International” below.

•International: Handles the displayed lyrics as a western language.

• Japanese: Handles the displayed lyrics as Japanese.

Play

Repeat Mode

Determines how playback of the current MIDI Song or Audio Song is repeated.

•Off:

Plays through the selected Song, then stops.

•Single: Plays through the selected Song repeatedly.

•All: Continues playback through all the Songs in the specified folder repeatedly.

•Random: Continues playback at random through all the Songs in the specified folder

repeatedly.

NOTE The preset Songs in the “Follow Lights” folder contain the Guide settings. These Songs are

inappropriate for use with the “All” or “Random” settings.

Phrase Mark

Repeat

Phrase Mark is a pre-programmed part of some Song data, which specifies a certain location

(set of measures) in the Song. When this is “On,” the section corresponding to the specified

Phrase Mark number is repeatedly played back. This parameter is available only when the

MIDI Song containing Phrase Mark settings is selected.

Quick Start

On some commercially available MIDI Song data, certain settings related to the MIDI Song

(such as Voice selection, volume, etc.) are recorded to the first measure, before the actual note

data. When Quick Start is set to “On,” the instrument reads all initial non-note data of the

Song at the highest possible speed, then automatically switches to the appropriate tempo at

the first note. This allows you to start playback as quickly as possible, with a minimum pause

for reading of data.

MIDI Song Fast

Forward Type

Determines the fast forward type of when pressing [ ] during MIDI Song playback.

•Jump:

Pressing [ ] once instantly sets the playback position to the next measure without

sounding. Holding [ ] scrolls forward continuously.

•Scrub: Pressing and holding [ ] plays and sounds the MIDI Song at high speed.

USB MIDI Song

Auto Open

When this is set to “On,” connecting the USB flash drive will call up the first MIDI Song in

the USB flash drive.

Performance

Assistant

Refer to page 89.

Song Settings Related to Playback/Recording

CVP-809/CVP-805 Reference Manual

Playing Backing Parts with the Performance Assistant Technology

This feature lets you play your own backing parts on the keyboard along with MIDI Song playback, and have them sound

perfectly appropriate (even though the notes you play might be wrong).

1 Select a MIDI Song containing chord data.

The Performance Assistant Technology is applied only to MIDI Songs containing chord data. To confirm whether

the selected Song contains chord data or not, call up the Home display with the Style area shown, then start playback

of the Song. If the current Song contains chord data, the current chord type appears in the Style area. After stopping

playback, go to the next step.

2 Call up the operation display via [Menu] → [SongSetting] → [Play].

3 Set the Performance Assistant to “On.”

NOTE Selecting a Song will turn off the Performance Assistant.

4 Press the SONG CONTROL [ / ] (PLAY/PAUSE) button to start playback.

5 Play the keyboard.

Along with MIDI Song playback, try playing a bass line in the left hand area while playing various phrases or chords

in the right hand area. Even if you do not know what notes should be played, don’t worry and play any keys as

desired! Only the harmonically “correct” notes matching the current chord are sounded, regardless of the notes you

actually play.

6 Press the SONG CONTROL [ ](STOP) button to stop playback.

Re-recording a Specific Section of the MIDI Song — Punch In/Out

When re-recording a specific section of an already-recorded MIDI Song, use the Punch In/Out function. In this method,

only the data between the Punch In point and the Punch Out point is overwritten with the newly recorded data. Keep in

mind that the notes before and after the Punch In/Out points are not recorded over, and you will hear them play back

normally to guide you in the Punch In/Out timing.

1 Call up the operation display via [Menu] → [SongSetting] → [Rec] → Page 1/2.

2 Set the parameters such as how the Recording starts/stops and the Punch In/Out position.

NOTE The parameters here cannot be set while recording.

Chord Detection

Priority

Determines the priority of the chords for accompaniment, either the ones contained in the

MIDI Song being played back or the chord you’ve just played in the chord section of the

keyboard.

•MIDI Song:

Gives priority to the chords contained in the MIDI Song.

•Keyboard: Gives priority to the chords you play in the chord section of the keyboard. Set this if

you want to practice playing chords with MIDI Song playback. Once you play in the chord

section during MIDI song playback, the instrument ignores the chords contained in the MIDI

Song until the playback ends.

Rec

Song Settings Related to Playback/Recording

CVP-809/CVP-805 Reference Manual

3 Select a MIDI Song to be re-recorded.

4 Press the [ ](REC) button to call up the Song Recording display, and then confirm that

[Overwrite MIDI] is selected.

If the Channel area is not shown, touch [ ] at the left of “Channel.”

5 From the display, set the part or parts you intended to re-record to [Rec], and set all other

parts to [Off].

NOTE For details about the recording channels, refer to the Owner’s Manual, Chapter 6.

Mode Rec Start

Determines the recording start behavior.

•Normal:

Overwrite recording starts when Song playback is started via the

SONG [ / ] (PLAY/PAUSE) button or when you play the keyboard in the

Synchro Standby mode.

•First Key On: The Song plays back normally, then starts overwrite recording

as soon as you play the keyboard.

•Punch In At: The Song plays back normally up to the beginning of the

“Punch In At” measure specified in the Punch In/Out parameter below, then

starts overwrite recording at that point.

Rec Stop

Determines the recording stop behavior, or how data is handled after

recording is stopped.

•Replace All:

This deletes all data after the point at which recording is

stopped.

•Punch Out: The Song position at which recording is stopped is regarded as

the Punch Out point. This setting maintains all data after the point at which

recording is stopped.

•Punch Out At: Actual overwrite recording continues until the beginning of

the “Punch Out” measure specified in the Punch In/Out parameter below, at

which point recording stops and normal playback continues. This setting

maintains all data after the point at which recording is stopped.

Punch In/

Out

Punch In At

Specifies the Punch In measure.

Punch Out At

Specifies the Punch Out measure.

Pedal Control

When this is set to “On,” you can use the center pedal to control the Punch

In and Punch Out points. While a Song is playing back, pressing (and

holding) the center pedal instantly enables Punch In recording, while

releasing the pedal stops recording (Punch Out). You can press and release

the center pedal as often as you want during playback. Note that the current

function assignment of the center pedal is cancelled when the Pedal Punch

In/Out function is set to “On.”

NOTE Pedal Punch In/Out operation may be reversed depending on the particular

pedal you’ve connected to the instrument. If necessary, change the pedal

polarity to reverse the control (page 43).

Song Settings Related to Playback/Recording

CVP-809/CVP-805 Reference Manual

6 Press the SONG CONTROL [ / ] (PLAY/PAUSE) button to start recording.

At the Punch In point specified in step 2, play the keyboard to start actual recording. At the Punch Out point

specified in step 2, stop playing the keyboard.

7 Touch (Save) which appears in the Song area of the Home display to save the recorded

Song.

NOTICE

The recorded Song data will be lost if you select another Song or turn the power to the instrument off without

executing the Save operation.

 Examples of re-recording with various Punch In/Out settings

This instrument features several different ways you use the Punch In/Out function. The illustrations below indicate a

variety of situations in which selected measures in an eight-measure phrase are re-recorded.

Setting the Audio File Format saved via Audio Recording

From the display called up via [Menu] → [SongSetting] → [Rec] → page 2/2, you can specify the Audio file format saved via

the Audio recording.

Audio Rec Format

•WAV: Your performance will be recorded in WAV format which features higher

audio quality than MP3, but the file size will be larger.

• MP3 128/256/320kbps: Your performance will be recorded in MP3 format

(MPEG-1 Audio Layer-3). The larger the value, the higher the quality, and the larger

the data size.

12345678

12345

12345678

12345

12345678

12345

12345678

6 812345 7

Recording Start setting

Recording Stop setting

Normal

Replace All

Normal

Punch Out

Normal

Punch Out at 006

First Key On

Replace All

First Key On

Punch Out

First Key On

Punch Out at 006

Punch In at 003

Replace All

Punch In at 003

Punch Out

Punch In at 003

Punch Out at 006

Original data

Start overwrite recording *1

Play back original data

Play the keyboard to start

overwrite recording

Start overwrite recording

Stop recording *2

Stop overwrite recording/play original data

Deleted

*1 To avoid overwriting measures 1 – 2, start recording from measure 3.

*2 To stop recording, press the [REC] button at the end of measure 5.

Previously recorded data

Newly recorded data

Deleted data

Deleted

Start overwrite recording *1 Stop recording *2

Start overwrite recording *1

Stop recording *2

Stop overwrite recording/play original data

Stop recording *2

Stop overwrite recording/play original data

Play back original data

Play the keyboard to start

overwrite recording

Play the keyboard to start

overwrite recording

Start overwrite recording

CVP-809/CVP-805 Reference Manual 92

Fine Tuning the Pitch

You can fine-tune the pitch of the entire instrument in 0.2 Hz steps—useful when you play the Clavinova along with other

instruments or CD music. Please note that the Tune function does not affect the Drum Kit or SFX Kit Voices and Audio

Songs. To restore the default initial setting (440.0 Hz), touch and hold down the setting value for a while.

Master Tune – Fine Tuning the Pitch of the Entire Instrument

Scale Tune – Selecting or Creating a Temperament

Keyboard parts

Fine Tuning the Pitch

CVP-809/CVP-805 Reference Manual

1 Select the desired Scale type (temperament).

You can select one of various scales for playing in custom tunings for specific historical periods or music genres.

2 Change the following settings as necessary.

To store the Scale Tune settings:

If you want to store the Scale Tune settings, use the Registration Memory. Press the REGISTRATION MEMORY

[MEMORY] button, then checkmark “Scale Tune” and press one of the REGISTRATION MEMORY [1] – [8] buttons to

Type

•Equal: The pitch range of each octave is divided equally into twelve parts, with each half-

step evenly spaced in pitch. This is the most commonly used tuning in music today.

•Pure Major, Pure Minor: These tunings preserve the pure mathematical intervals of each

scale, especially for triad chords (root, third, fifth). You can hear this best in actual vocal

harmonies — such as choirs and a cappella singing.

•Pythagorean: This scale was devised by the famous Greek philosopher and is created from

a series of perfect fifths, which are collapsed into a single octave. The 3rd in this tuning are

slightly unstable, but the 4th and 5th are beautiful and suitable for some leads.

• Mean-Tone: This scale was created as an improvement on the Pythagorean scale, by making

the major third interval more “in tune.” It was especially popular from the 16th century to

the 18th century. Handel, among others, used this scale.

• Werckmeister, Kirnberger: This composite scale combines the Werckmeister and

Kirnberger systems, which were themselves improvements on the mean-tone and

Pythagorean scales. The main feature of this scale is that each key has its own unique

character. The scale was used extensively during the time of Bach and Beethoven, and even

now it is often used when performing period music on the harpsichord.

•Arabic1, Arabic2: Use these tunings when playing Arabic music.

Base Note

Determines the base note for each scale. When the base note is changed, the pitch of the

keyboard is transposed, yet maintains the original pitch relationship between the notes.

Tune [cent]

Select the desired note to be tuned and tune it in cents. If you edit this parameter,

“(Edited)” is shown at the right of “Type” in step 1.

NOTE In musical terms a “cent” is 1/100th of a semitone. (100 cents equal one semitone.)

(Parts)

Checkmark the part to which the Scale Tune setting is applied.

CVP-809/CVP-805 Reference Manual 94

Setting the Touch Sensitivity of the

Keyboard

You can adjust the touch response of the instrument (how the sound responds to the way you play the keys). This setting

does not change the weight of the keyboard.

For information about this display, refer to the Owner’s Manual, Chapter 1.

CVP-809/CVP-805 Reference Manual 95

Metronome Settings

Metronome

Volu me

Determines the level of the metronome sound.

Sound

Determines which sound is used for the metronome.

•Bell Off:

Conventional metronome sound, with no bell.

•Bell On: Conventional metronome sound, with bell.

•English Voice: Count in English

•German Voice: Count in German

• Japanese Voice: Count in Japanese

•French Voice: Count in French

•Spanish Voice: Count in Spanish

Time Signature

Determines the time signature of the metronome sound.

Tap Tempo

Volu me

Adjusts the volume of the sound triggered when the [TAP TEMPO] button is pressed.

Sound

Selects the percussion instrument as sound triggered when the [TAP TEMPO] button is

pressed.

CVP-809/CVP-805 Reference Manual 96

MIDI Settings

In this section, you can make MIDI-related settings for the instrument. This instrument gives you a set of ten pre-

programmed templates that let you instantly and easily reconfigure the instrument to match your particular MIDI

application or external device. Also, you can edit the pre-programmed templates and save up to ten of your original

templates.

NOTE No MIDI signals are received in the Piano Room.

1 Touch the box (shown above), then select a pre-programmed MIDI template (below).

If you have already created an original MIDI template and saved it to User memory (in steps 2 and 3 below), you can

also select that template from User memory.

2 If desired, edit the MIDI parameters based on the MIDI template selected in step 1 in the

relevant setting display.

• System: Lets you set the MIDI System related parameters.........................................................................page 97

•

Transmit: Lets you set the MIDI Transmission related parameters.........................................................page 98

•

Receive: Lets you set the MIDI Reception related parameters. .................................................................page 99

•

On Bass Note: Lets you select the MIDI channels of which the MIDI data coming from the external MIDI

device will be used for detecting the bass note for Style playback. .......................................................... page 100

•

Chord Detect: Lets you select the MIDI channels of which the MIDI data coming from the external MIDI

device will be used for detecting the chord type for Style playback......................................................... page 101

3 When you’ve finished editing in each display, touch (Save) to save the MIDI settings as

your original MIDI Template.

NOTE Your original MIDI templates can be saved as a single file to a USB flash drive. On the display called up via [Menu] 

[Utility]  [Factory Reset/Backup]  page 2/2, touch [Backup] of “MIDI” to execute the Save operation (page 105).

 Pre-programmed MIDI Templates

All Parts

Transmits all parts including the keyboard parts (Main, Layer and Left), with the

exception of Song parts.

KBD & STYLE

Basically the same as “All Parts” with the exception of how keyboard parts are managed.

The right-hand parts are handled as “Upper” instead of Main and Layer, and the left-hand

part is handled as “Lower.”

MIDI Settings

CVP-809/CVP-805 Reference Manual

The explanations here apply when you call up “System” display in step 2 on page 96.

Master KBD

(Master Keyboard)

In this setting, the instrument functions as a “master” keyboard, playing and controlling

one or more connected tone generators or other devices (such as a computer/sequencer).

Song

With this setting, only the Song channels 1 – 16 are transmitted from this instrument via

the corresponding channel numbers 1 – 16 respectively. This is used to play Song data

with an external tone generator and to record Song data to an external sequencer.

Clock Ext

(Clock External)

Playback or recording (Song, Style, etc.) synchronizes with an external MIDI clock instead

of the instrument’s internal clock. This template should be used when you wish to set the

tempo on the MIDI device connected to the instrument.

MIDI Accord1

(MIDI Accordion 1)

MIDI accordions allow you to transmit MIDI data and play connected tone generators

from the keyboard and bass/chord buttons of the accordion. This template lets you

control the keyboard performance and Style playback from a MIDI Accordion.

MIDI Accord2

(MIDI Accordion 2)

Basically the same as “MIDI Accord1” above, with the exception that the chord/bass notes

you play with your left hand on a MIDI Accordion are recognized also as MIDI note

events.

MIDI Pedal1

MIDI pedal units allow you play connected tone generators with your feet (especially

convenient for playing single note bass parts). This template lets you play/control the

chord root in Style playback with a MIDI pedal unit.

MIDI Pedal2

This template lets you play the bass part for Style playback by using a MIDI pedal unit.

MIDI OFF

No MIDI signals are sent or received.

System – MIDI System Related Settings

Clock

Determines whether the instrument is controlled by its own internal clock (“Internal”) or

a MIDI clock (“MIDI,” “USB1,” “USB2,” and “Wireless LAN”) received from an external

device. “Internal” is the normal Clock setting when the instrument is being used alone or

as a master keyboard to control external devices. If you are using the instrument with an

external sequencer, MIDI computer, or other MIDI device, and you want to synchronize it

to that device, set this parameter to the appropriate setting: “MIDI,” “USB 1,” “USB 2,” or

“Wireless LAN.” In this case, make sure that the external device is connected properly

(e.g., to the instrument’s MIDI IN terminal), and that it is properly transmitting a MIDI

clock signal. When this is set for control by an external device (“MIDI,” “USB1,” “USB2,”

or “Wireless LAN”), the Tempo is indicated as “Ext.” in the Tempo display.

NOTE If the Clock is set other than “Internal,” the Style, Song, Metronome and Tempo cannot be

controlled by the buttons on this instrument.

NOTE “Wireless LAN” is shown only when the USB Wireless LAN adaptor (UD-WL01) is connected

to this instrument.

Transmit Clock

Turns MIDI clock (F8) transmission on or off. When set to “Off,” no MIDI clock or Start/

Stop data is transmitted even if a Song or Style is played back.

Transpose MIDI

Input

Determines whether or not the instrument’s transpose setting is applied to the note events

received from the external device via MIDI.

Start/Stop

Determines whether incoming FA (start) and FC (stop) messages affect Song or Style

playback.

MIDI Settings

CVP-809/CVP-805 Reference Manual

The explanations here apply when you call up the “Transmit” display in step 2 on page 96. This determines which MIDI

channel is used for each part when MIDI data is transmitted from this instrument.

1 For each Part, select the MIDI Transmit Channel with which the MIDI data of the

corresponding Part is to be transmitted.

With the exception of the two parts below, the configuration of the parts is the same as those already explained

elsewhere in the Owner’s Manual.

•

Upper: A keyboard part played on the right side of the keyboard from the Left Split Point.

•

Lower: A keyboard part played on the left side of the keyboard from the Left Split Point. This is not affected by

the on/off status of the [ACMP ON/OFF] button.

NOTE If the same transmit channel is assigned to several different parts, the transmitted MIDI messages are merged to a single

channel — resulting in unexpected sounds and possible glitches in the connected MIDI device.

NOTE Protected Songs cannot be transmitted even if the proper Song channels 1 – 16 are set to be transmitted.

Local Control

Turns the Local Control for each part on or off. When Local Control is set to “On,” the

keyboard of the instrument controls its own (local) internal tone generator, allowing the

internal Voices to be played directly from the keyboard. If you set Local Control to “Off,”

the keyboard and controllers are internally disconnected from the instrument’s tone

generator section so that no sound is output when you play the keyboard or use the

controllers. For example, this allows you to use an external MIDI sequencer to play the

instrument’s internal Voices, and use the instrument keyboard to record notes to the

external sequencer and/or play an external tone generator.

System

Exclusive

Message

Transmit

Determines whether MIDI System Exclusive messages are transmitted (On) or not (Off)

from this instrument.

Receive

Determines whether MIDI System Exclusive messages are recognized (On) or not (Off)

by this instrument.

Chord

System

Exclusive

Message

Transmit

Determines whether MIDI chord system exclusive data (Chord Detect: root and type) are

transmitted (On) or not (Off) from this instrument.

Receive

Determines whether MIDI chord system exclusive data (Chord Detect: root and type) are

recognized (On) or not (Off) by this instrument.

Transmit – MIDI Transmit Channel Settings

Lets you alternate between two pages.

The dots corresponding to each channel (1–16) flash briefly whenever

any data is transmitted on the channel(s).

MIDI Settings

CVP-809/CVP-805 Reference Manual

2 Touch [ ] to call up the other page then select which MIDI messages are to be transmitted

for each Part.

The following MIDI messages can be set on the Transmit/Receive display.

•

Note (Note events) ............................ page 74

•

CC (Control Change)....................... page 74

•

PC (Program Change)..................... page 74

•

PB (Pitch Bend) ................................. page 74

•

AT (Aftertouch) ................................. page 74

The explanations here apply when you call up the “Receive” display in step 2 on page 96. This determines which Part is

used for each MIDI channel when the MIDI data is recognized by this instrument.

1 For each Channel, select the Part which is to handle the MIDI data of the corresponding

channel received from the external MIDI device.

When connecting via USB, MIDI data of 32 channels (16 channels x 2 Ports) can be handled by this instrument.

With the exception of the two parts below, the configuration of the parts is the same as those already explained

elsewhere in the Owner’s Manual.

•

Keyboard: The received note messages control the instrument’s keyboard performance.

•

Extra Part 1 – 5: These five parts are specially reserved for receiving and playing MIDI data. Normally, these

parts are not used by the instrument itself.

2 Touch [ ] to call up the other page then select which MIDI messages are to be received for

each Channel.

Receive – MIDI Receive Channel Settings

Lets you alternate between two pages.

The dots corresponding to each channel (1–16) flash briefly whenever any

data is received on the channel(s).

MIDI Settings

CVP-809/CVP-805 Reference Manual

100

The explanations here apply when you call up “On Bass Note” display in step 2 on page 96. The settings here let you

determine the bass note for Style playback, based on the note messages received via MIDI. The note on/off messages

received at the channel(s) set to on are recognized as the bass notes of the chords for Style playback. The bass note will be

detected regardless of the [ACMP ON/OFF] or Split Point settings. When several channels are simultaneously set to on,

the bass note is detected from merged MIDI data received over the channels.

Touch the desired channel number to enter the checkmark. Touch the same location again to remove the checkmark.

MIDI transmission/reception via the USB terminal, Wireless LAN, and MIDI terminals

The relationship between the MIDI terminals, Wireless LAN and the [USB TO HOST] terminal which can be used

for transmitting/receiving 32 channels (16 channels x 2 ports) of the MIDI messages is as follows:

On Bass Note – Setting the Bass Note for Style Playback

USB2

USB1

MIDI transmission

MIDI OUT

terminal

Wireless

LAN

USB TO HOST

terminal

Merge

MIDI/USB1/

Wireless LAN 1 – 16

MIDI reception

MIDI IN

terminal

Port handling

USB2

1 – 16

Wireless

LAN

USB TO HOST

terminal

MIDI/USB1/Wireless LAN 1 – 16

MIDI Settings

CVP-809/CVP-805 Reference Manual

101

The explanations here apply when you call up “Chord Detect” display in step 2 on page 96. The settings here let you

determine the chord type for Style playback, based on the note messages received via MIDI. The note on/off messages

received at the channel(s) set to on are recognized as the notes for detecting chords in Style playback. The chords to be

detected depend on the fingering type. The chord types will be detected regardless of the [ACMP ON/OFF] or split point

settings. When several channels are simultaneously set to on, the chord type is detected from merged MIDI data received

over the channels.

Touch the desired channel number to enter the checkmark. Touch the same location again to remove the checkmark.

Chord Detect – Setting the Chord Type for Style Playback

CVP-809/CVP-805 Reference Manual 102

Making Global Settings (Utility)

Speaker/Connectivity

Speaker

Determines how the sound is output from the speaker of this instrument.

•Headphone Switch:

Speaker sounds normally, but is cut off when headphones are

inserted to the [PHONES] jack.

•On: Speaker sound is always on.

•Off: Speaker sound is off. You can only hear the instrument sound via the headphones

or an external device connected to the AUX OUT jacks.

Binaural

Turns the Binaural Sampling function or the Stereophonic Optimizer function for

VRM Voices on or off.

When the function is on and headphones are connected to the [PHONES] jack, the

sound from the headphones is affected by these functions. However, when

headphones are connected, these functions also affect the sound from the external

speaker connected to the AUX OUT jacks or the sound for Audio recording (by using

the Bluetooth Audio function or USB Audio Interface function), and may result

unusual or unnatural sound. If this happens, turn this function off.

For details about Binaural Sampling and Stereophonic Optimizer, refer to “Using

Headphones” in the “Starting Up” section of the Owner’s Manual.

NOTE If the “Speaker” setting above is “On,” the effect is not applied even when “Binaural” is

set to on.

IAC

Turns on or off the IAC (Intelligent Acoustic Control). With this function, the sound

quality of this instrument is automatically adjusted and controlled according to the

overall volume. Even when the volume is low, this lets you hear both low sounds and

high sounds clearly.

IAC Depth

Adjusts the IAC depth.

Audio Loopback

Determines whether audio input from the connected computer or smart device is

output to a computer or a smart device or not. For details, refer to the Owner’s

Manual, Chapter 10.

AUX IN Noise Gate

Turns on or off the Noise Gate which minimizes noise of the sound input via the

[AUX IN] jack.

Making Global Settings (Utility)

CVP-809/CVP-805 Reference Manual

103

Page 1/2

For information about this display, refer to “Changing the Brightness of Display” in the “Starting Up” section of the

Owner’s Manual.

Page 2/2

This function is used to “lock” specific parameters (effect, split point, etc.) to make them selectable only via the panel

control — in other words, instead of being changed via Registration Memory, One Touch Setting, Music Finder, or Song

and sequence data.

To lock the desired parameter, touch the corresponding box to enter the checkmark. To unlock the parameter, touch the

box again.

Display Out Content

Determines the video content which is output to a connected external monitor, such

as a television.

•Lyrics/Text:

Only the lyrics of the Song or text files (whichever you used last time) are

output, regardless of the display that is called up on the instrument.

•LCD: The currently selected display is output.

Touch Screen/Display

Display Home Theme

Touch and change the theme (background) of the Home display.

The available settings are Piano/White/Black.

Time Stamp

Determines whether the time stamp of a file is shown on the User tab of the File

Selection display or not.

NOTE When the instrument is connected to a network via the USB wireless LAN adaptor (UD-

WL01), the current time is taken from the network and displayed. For details, refer to

page 110.

Voi ce

Number

Determines whether or not the Voice bank and number are shown in the Voice

Selection display. This is useful when you want to check which bank select MSB/LSB

values and program change number you need to specify when selecting the Voice

from an external MIDI device.

Pop-up

Display Time

Determines the time that elapses before the pop-up windows close. Pop-up windows

appear when you press buttons TEMPO [-]/[+], TRANSPOSE [-]/[+], SONG

CONTROL [ ](REW)/[ ](FF), or REGISTRATION BANK [-]/[+]. When

“Hold” is selected here, the pop-up window is shown until you touch [X].

Transiti on

Effect

Turns on or off the Transition Effect which is applied when the display is changed.

NOTE Transition effects on the instrument’s display cannot be output.

Voice Area

Determines which keyboard parts are shown in the Voice area of the Home display.

When “Show Active Parts Only” is selected, only the active keyboard parts are

shown. When “Show All Parts” is selected, all the keyboard parts are shown.

Parameter Lock

Making Global Settings (Utility)

CVP-809/CVP-805 Reference Manual

104

This lets you execute the Format operation or check the memory capacity (approximate value) of the User memory or the

connected USB flash drive.

The User memory is indicated as “USER,” and the USB flash drives are indicated as “USB 1” or “USB 2,” depending on the

number of the connected devices.

To format the drive, select the drive and then touch [Format].

NOTICE

The format operation overwrites any previously existing data. Make sure that the drive you are formatting does not

contain important data. Proceed with caution.

Page 1/2

For information about this display, refer to “Making the Basic Settings” in the “Starting Up” section of the Owner’s

Manual.

Page 2/2

To use Voice Guide, you need to download the Voice Guide (audio) file from the Yamaha website, and save it to USB flash

drive, which you then connect to this instrument. For information on using Voice Guide, refer to the Voice Guide Tutorial

Manual (simple text file).

The Voice Guide (audio) file and the Voice Guide Tutorial Manual are available via the following URL:

http

s://download.yamaha.com/

Storage

System

Voice Guide

Determines whether or not Voice Guide is used (On/Off), when USB flash drive

containing the Voice Guide (audio) file is properly connected to this instrument. This

setting can also be changed by pressing and holding the [DEMO] button for longer

than three seconds.

Voice Guide Controller

By holding the controller set here and then pressing the panel button or touching the

item on the display, you can hear the corresponding name (with no execution of the

function).

Voice Guide Volume

Adjusts the volume of Voice Guide.

Making Global Settings (Utility)

CVP-809/CVP-805 Reference Manual

105

Factory Reset — Restoring the Factory Programmed Settings

On page 1/2, checkmark the boxes of the desired parameters then touch [Factory Reset] to initialize the settings of the

parameters which are checkmarked.

NOTE If you want to delete all data in the User memory, format the memory via [Menu]  [Utility]  [Storage] (page 104).

Backup/Restore – Saving and Recalling Your Original Settings as a Single File –

For the items below, you can save your original settings to the internal User memory or USB flash drive as a single file for

future recall.

1 Make all desired settings on the instrument, then call up page 2/2 of the “Factory Reset/

Backup” display.

2 As necessary, connect a USB flash drive to the [USB TO DEVICE] terminal.

If you want to save all settings, you can only use the USB flash drive to save the data.

3 Touch [Backup] or [Save] of the desired item to save the data.

Factory Reset/Backup

System

Restores the System Setup parameters to the original factory settings. Refer to “Parameter Chart”

in the Data List (separate PDF) for details about which parameters belong to the System Setup.

MIDI

Restores the MIDI settings including the MIDI templates saved in the internal User memory to

the original factory status.

User Effect

Restores the User Effect settings including the following data to the original factory settings.

•

User Effect types (page 13)

• User Master EQ types (page 12)

• User Master Compressor types (page 16)

• User Vocal Harmony types (page 32)

• User Microphone Settings (page 27)

Registration

Turns off all the REGISTRATION MEMORY [1] – [8] lamps, indicating that no Registration

Memory Bank is selected although all the Bank files are maintained. In this status, you can create

Registration Memory setups from the current panel settings.

Favorite

Removes all files from the Favorite tab on the Voice Selection display and the Style Selection

display.

Making Global Settings (Utility)

CVP-809/CVP-805 Reference Manual

106

 Backup/Restore

All settings and data in the User memory of this instrument (except for protected Song) are saved to the USB flash

drive as a single file named “CVP-809.bup” or “CVP-805.bup.”

If you want to contain the Audio Songs (WAV/MP3) saved to the User memory in the same file, enter the

checkmark to the “Include Audio Files” box. If you do not want to save the Audio files because of the large data size,

remove the checkmark.

 Setup Files

The following settings are saved as a file individually.

Select the desired destination to save the file, and then touch [Save here]. You can change the file name as necessary.

To call up the saved data:

Touch [Restore] or [Load] of the desired item, then select the desired file.

If you want to restore the factory programmed settings, select the setup file in the “Preset” tab.

NOTICE

• Files including Protected Songs in the User memory of the instrument are replaced by restoring the backup file. Move

or copy the files in the User memory of the instrument to USB flash drive before restoring.

• Completing the backup/restore operation may take a few minutes. Do not turn off the power during backup or

restoring. If you turn off the power during backup or restoring, data may be lost or damaged.

System

Parameters set on the various displays such as “Utility” are handled as a single System Setup

file. Refer to “Parameter Chart” in the Data List (separate PDF) for details on which

parameters belong to System Setup.

MIDI

The MIDI settings including the MIDI templates on the internal User memory are handled

as a single MIDI Setup file.

User Effect

The User Effect settings including the following data can be managed as a single file.

•

User Effect types (page 13)

• User Master EQ types (page 12)

• User Master Compressor types (page 16)

• User Vocal Harmony types (page 32)

• User Microphone Settings (page 27)

CVP-809/CVP-805 Reference Manual 107

Connecting to a Bluetooth-equipped

Device

For information about this display, refer to the Owner’s Manual, Chapter 10.

CVP-809/CVP-805 Reference Manual 108

Wireless LAN Settings

This icon is shown only when the USB Wireless LAN adaptor (UD-WL01) is connected to the [USB TO DEVICE]

terminal. Make sure the adaptor is connected before executing any operations.

This instrument can be connected to a smart device via wireless LAN. For general operating instructions, refer to the

“Smart Device Connection Manual” (separate PDF). This section covers only operations that are specific to this

instrument.

When the connection is done successfully, “Connected” is shown at the top of the display, and one of the icons shown

below appears indicating the signal strength.

Infrastructure Mode

Networks Connecting to a network listed on the display:

From the Networks listed on the display, select the desired one. For a network

having a lock icon ( ), you need to enter the password and touch [Connect]; for

a network without a lock icon, you can connect the network only by selecting it.

Manual Setup:

Touch [Other] displayed at the very end of the list to call up the Manual Setup

display, for making SSID, security, and password settings. After entering them,

touch [Connect] on the Manual Setup display to connect to the network.

Update Networks

Updates the Network List on the display.

Connect by WPS

Connects this instrument to the network via WPS. After touching [Start WPS] in

the window appeared by touching here, press the WPS button of the desired

wireless LAN access point within two minutes.

NOTE Make sure that your access point supports WPS. About the confirmation and

changes in the access point settings, refer to the manual of the access point.

Initialize

Initializes the connection setup to the default factory status.

Strong

Weak

Wireless LAN Settings

CVP-809/CVP-805 Reference Manual

109

Detail

Lets you set detailed parameters such as the static IP address. After setting, touch

[OK].

Mode

Switches to the Access Point Mode.

Access Point Mode

Initialize

Initializes the connection setup to the default factory status.

Detail

Sets the detailed parameters.

•1/3 page:

Sets the SSID, security, password, and channel.

•2/3 page: Sets the IP address and other related parameters.

•3/3 page: Enters the Host name or shows MAC address, etc.

Mode

Switches to the Infrastructure Mode.

CVP-809/CVP-805 Reference Manual 110

Making the Time Settings

This icon is shown only when the USB Wireless LAN adaptor (UD-WL01) is connected to the [USB TO DEVICE]

terminal. Make sure the adaptor is connected before executing any operations.

When the instrument is connected to a network and the current time is retrieved from the network successfully, the

current time is displayed above the icon. Make sure to connect by Infrastructure Mode. For details on the connections,

refer to the “Smart Device Connection Manual” (separate PDF).

NOTE When the instrument cannot retrieve the current time from the network, the time displayed will not be correct.

Time Zone

Touch to sel ec t t he Time Z one.

Daylight Saving Time

Touch to turn daylight-saving time on or off.

CVP-809/CVP-805 Reference Manual 111

Index

Numerics

3 Band EQ ......................................... 26

Access Point Mode ........................109

Amplitude ......................................... 50

Any Key ............................................ 87

Articulation ...................................... 44

Assembly ........................................... 59

Assignable ......................................... 46

Attack ................................................ 49

Attenuator ........................................ 27

Audio File Format ........................... 91

Audio Loopback ............................ 102

Audio Rec Format ........................... 91

Backup ............................................105

Balance ..........................................9, 10

Bar Clear ........................................... 61

Bar Copy ........................................... 61

Bass Hold .......................................... 45

Beat Converter ................................. 60

Binaural ...........................................102

Block Diagram ................................. 17

Bluetooth ........................................107

Brightness ...................................10, 49

Bypass ................................................ 64

Channel Edit ..............................60, 76

Chord ................................................ 19

Chord Cancel ..................................... 7

Chord Detect ............................89, 101

Chord Detection Area ...................... 7

Chord Looper ................................... 38

Chord Source ................................... 29

Chord Tutor ....................................... 8

Chordal ............................................. 29

Chorus ............................................... 14

Clock .............................. 68, 71, 75, 97

Color ................................................. 19

Compression .................................... 16

Compressor ................................15, 26

Cutoff frequency .............................. 49

Decay ................................................. 49

Display ............................................103

Dorian ...............................................64

Drums ................................................82

Dynamics ..........................................61

Dynamics Control ...........................84

Each Key Setting ..............................80

Echo ...................................................25

Effect ........................................... 12, 50

EG (Envelope Generator) ...............49

EQ (Equalizer) ..................................11

Equalizer ...........................................11

Event Filter ........................................75

Event List ............................. 68, 71, 74

Expand ...............................................74

Factory Reset ..................................105

Fade In/Out ......................................45

Filter ............................................ 10, 49

Fingering Type ...................................6

Follow Lights ....................................87

Footage ..............................................51

Glide ..................................................44

GM Voice ..........................................83

Groove ...............................................60

Guide .......................................... 18, 87

Guitar .................................................63

Harmonic Cont. ...............................49

Harmonic Content ................... 10, 49

Harmonic Minor ..............................64

Harmony Assign ..............................31

Harmony note ..................................30

Harmony Type .................................24

High Key ...........................................65

IAC (Intelligent Acoustic Control)

..........................................................102

Infrastructure Mode ......................108

Insertion Effect .................... 12, 13, 50

Jump ..................................................88

Karao-Key ........................................ 87

Key Signature ................................... 19

Keyboard Harmony ........................ 24

Lead note .......................................... 30

Left Hold On/Off ............................. 46

LFO Amplitude ............................... 50

LFO Filter ......................................... 50

LFO Pitch ......................................... 50

Local Control ................................... 98

Loop Recording ............................... 56

Lyrics ...........................................19, 20

Manual Bass ....................................... 7

Manual Setup ................................. 108

Master Compressor ......................... 15

Master EQ ........................................ 11

Master Tune ..................................... 92

MegaVoice ..................................82, 83

Melodic Minor ................................. 64

Metronome ...................................... 95

Microphone ...................................... 26

MIDI ................................................. 96

MIDI Accordion .............................. 97

MIDI Pedal ....................................... 97

MIDI Receive Channel ................... 99

MIDI reception .............................. 100

MIDI Template ................................ 96

MIDI transmission ........................ 100

MIDI Transmit Channel ................ 98

Mixer ................................................. 10

Modulation ...........................44, 49, 50

Mono ...........................................46, 48

Mono Type ....................................... 48

MP3 ................................................... 91

Multi Assign ..................................... 25

Music Notation ................................ 18

Natural Minor .................................. 64

Network .......................................... 108

Noise Gate ........................................ 26

Note ................................................... 19

Note Limit ........................................ 65

Note Name ....................................... 19

NTR (Note Transposition Rule) ... 63

CVP-809/CVP-805 Reference Manual 112

NTT (Note Transposition Table) .. 64

Octave ............................................... 78

On Bass Note ..................................100

Organ Flutes ...............................51, 82

Original Beat .................................... 60

OTS Link Timing ............................ 85

Output ............................................... 16

Overdub Recording ......................... 56

Pan ..................................................... 15

Parameter Lock .............................. 103

Part EQ .............................................. 11

Pattern Length ................................. 55

Pedal .................................................. 43

Performance Assistant .................... 89

Phrase Mark Repeat ........................ 88

Pitch Bend ........................................ 44

Pitch Bend Range ............................ 78

Pitch Detect ...................................... 27

Pitch Shift ......................................... 65

Play Root/Chord .............................. 63

Playlist ............................................... 33

Poly ..............................................46, 48

Portamento ....................................... 44

Portamento Time ......................48, 78

Punch In/Out .......................89, 90, 91

Quantize ........................ 19, 61, 76, 77

Quick Start ........................................ 88

Ratio .................................................. 26

Realtime Recording ...................56, 66

Registration Freeze .......................... 37

Registration Memory ...................... 35

Registration Sequence ..................... 35

Release ............................................... 49

Repeat Mode .................................... 88

Resonance ......................................... 49

Restore ............................................105

Retrigger ........................................... 65

Reverb ............................................... 14

Root Fixed ........................................ 63

Root Trans (Root Transpose) ........ 63

Rotary Speaker ................................. 51

RTR (Retrigger Rule) ...................... 65

Scale Tune ........................................ 92

Scale type ...........................................93

Score ..................................................18

Scrub ..................................................88

SFF Edit .............................................62

SFX .....................................................82

Shortcut ...............................................3

Soft .....................................................44

Song ...................................................87

Song Creator .....................................66

Song Position ....................... 68, 71, 75

Sostenuto ...........................................44

Source Pattern ..................................53

Source Root/Chord ..........................63

Speaker ............................................102

Split Point .....................................6, 24

Step Recording .......................... 59, 66

Stop ACMP .......................................84

Stroke .................................................64

Style ....................................................84

Style Characteristics ........................86

Style Creator .....................................53

Style File Format ..............................62

Sustain ...............................................44

Swing .................................................60

Synchro Stop Window ....................85

System Effect ....................................12

Talk ............................................. 26, 28

Talk Mixing ......................................27

Tap Tempo .......................................95

Temperament ...................................92

Tempo .................................................4

Text ....................................................22

Texture ..............................................16

Threshold (Th.) ................................26

Time .................................................110

Time Signature .................................95

Time Stamp ....................................103

Touch Screen ..................................103

Touch Sensitivity ...................... 48, 94

Touch Sensitivity Depth .................48

Touch Sensitivity Offset ..................48

Transpose ......................................5, 77

Tremolo .............................................25

Trill ....................................................25

Tuning ........................................ 78, 92

User Effect .............................. 105, 106

Utility ...............................................102

Variation Effect .........................12, 13

Vibe Rotor ........................................ 44

Vibrato .............................................. 49

Vocal Harmony ............................... 28

Vocoder ............................................ 29

Vocoder-Mono ................................ 29

Voice ................................................. 78

Voice Characteristics ...................... 81

Voice Edit ................................... 47, 51

Voice Guide ................................... 104

Volume ............................................. 15

VRM .................................................. 81

WAV ................................................. 91

Wireless LAN ................................. 108

WPS ................................................. 108

XG Voice .......................................... 83

Your Tempo ..................................... 87

Manual Development Group

Published 08/2020 MW-B0

Yamaha CVP-805 Handleiding

Merk: Yamaha

Model: CVP-805

Categorie: Synthesizer

Type: Handleiding

Deze handleiding is ook geschikt voor

CVP-809

Download PDF

rapport

in andere talen

English: Yamaha CVP-805 User manual
italiano: Yamaha CVP-805 Manuale utente
русский: Yamaha CVP-805 Руководство пользователя
français: Yamaha CVP-805 Manuel utilisateur
español: Yamaha CVP-805 Manual de usuario
Deutsch: Yamaha CVP-805 Benutzerhandbuch
português: Yamaha CVP-805 Manual do usuário
dansk: Yamaha CVP-805 Brugermanual
čeština: Yamaha CVP-805 Uživatelský manuál
polski: Yamaha CVP-805 Instrukcja obsługi
română: Yamaha CVP-805 Manual de utilizare

Andere documenten

TCElectronic DITTO X2 LOOPER Snelstartgids

Yamaha CVP-805 Handleiding

Deze handleiding is ook geschikt voor

Yamaha CVP-805 Handleiding

in andere talen

Gerelateerde artikelen

Andere documenten