Yamaha QY70 Handleiding

Categorie
Digitale piano's
Type
Handleiding
Owner’s Manual
SPECIAL MESSAGE SECTION
This product utilizes batteries or an external power
supply (adapter). DO NOT connect this product to
any power supply or adapter other than one
described in the manual, on the name plate, or
specifically recommended by Yamaha.
WARNING: Do not place this product in a position
where anyone could walk on, trip over ,or roll
anything over power or connecting cords of any kind.
The use of an extension cord is not recommended!
IF you must use an extension cord, the minimum
wire size for a 25' cord (or less ) is 18 AWG. NOTE:
The smaller the AWG number ,the larger the current
handling capacity. For longer extension cords,
consult a local electrician.
This product should be used only with the
components supplied or; a cart, rack, or stand that is
recommended by Yamaha. If a cart, etc., is used,
please observe all safety markings and instructions
that accompany the accessory product.
SPECIFICATIONS SUBJECT TO CHANGE:
The information contained in this manual is believed
to be correct at the time of printing. However,
Yamaha reserves the right to change or modify any
of the specifications without notice or obligation to
update existing units.
This product, either alone or in combination with an
amplifier and headphones or speaker/s, may be
capable of producing sound levels that could cause
permanent hearing loss. DO NOT operate for long
periods of time at a high volume level or at a level
that is uncomfortable. If you experience any hearing
loss or ringing in the ears, you should consult an
audiologist.
IMPORTANT: The louder the sound, the shorter the
time period before damage occurs.
Some Yamaha products may have benches and / or
accessory mounting fixtures that are either supplied
with the product or as optional accessories. Some of
these items are designed to be dealer assembled or
installed. Please make sure that benches are stable
and any optional fixtures (where applicable) are well
secured BEFORE using.
Benches supplied by Yamaha are designed for
seating only. No other uses are recommended.
NOTICE:
Service charges incurred due to a lack of knowledge
relating to how a function or effect works (when the
unit is operating as designed) are not covered by the
manufacturer’s warranty, and are therefore the
owners responsibility. Please study this manual
carefully and consult your dealer before requesting
service.
ENVIRONMENTAL ISSUES:
Yamaha strives to produce products that are both
user safe and environmentally friendly. We sincerely
believe that our products and the production
methods used to produce them, meet these goals. In
keeping with both the letter and the spirit of the law,
we want you to be aware of the following:
Battery Notice:
This product MAY contain a small non-rechargeable
battery which (if applicable) is soldered in place. The
average life span of this type of battery is approxi-
mately five years. When replacement becomes
necessary, contact a qualified service representative
to perform the replacement.
This product may also use “household” type
batteries. Some of these may be rechargeable. Make
sure that the battery being charged is a rechargeable
type and that the charger is intended for the battery
being charged.
When installing batteries, do not mix batteries with
new, or with batteries of a different type. Batteries
MUST be installed correctly. Mismatches or incorrect
installation may result in overheating and battery
case rupture.
Warning:
Do not attempt to disassemble, or incinerate any
battery. Keep all batteries away from children.
Dispose of used batteries promptly and as regulated
by the laws in your area. Note: Check with any
retailer of household type batteries in your area for
battery disposal information.
Disposal Notice:
Should this product become damaged beyond repair,
or for some reason its useful life is considered to be
at an end, please observe all local, state, and federal
regulations that relate to the disposal of products
that contain lead, batteries, plastics, etc. If your
dealer is unable to assist you, please contact
Yamaha directly.
NAME PLATE LOCATION:
The name plate is located on the bottom of the
product. The model number, serial number, power
requirements, etc., are located on this plate. You
should record the model number, serial number, and
the date of purchase in the spaces provided below
and retain this manual as a permanent record of
your purchase.
Model
Serial No.
Purchase Date
92-BP
PLEASE KEEP THIS MANUAL
1
Do not open the instrument or attempt to disassemble
the internal parts or modify them in any way. The in-
strument contains no user-serviceable parts. If it should
appear to be malfunctioning, discontinue use immedi-
ately and have it inspected by qualified Yamaha ser-
vice personnel.
Do not expose the instrument to rain, use it near water
or in damp or wet conditions, or place containers on it
containing liquids which might spill into any openings.
If the AC adaptor cord or plug becomes frayed or dam-
aged, or if there is a sudden loss of sound during use of
the instrument, or if any unusual smells or smoke should
appear to be caused by it, immediately turn off the
power switch, disconnect the adaptor plug from the
outlet, and have the instrument inspected by qualified
Yamaha service personnel.
Use the specified adaptor (PA-3B or equivalent recom-
mended by Yamaha) only. Using the wrong adaptor
can result in damage to the instrument or overheating.
Before cleaning the instrument, always remove the
electric plug from the outlet. Never insert or remove an
electric plug with wet hands.
• Check the electric plug periodically and remove any
dirt or dust which may have accumulated on it.
WARNING
Always follow the basic precautions listed below to avoid the possibility of serious injury or
even death from electrical shock, short-circuiting, damages, fire or other hazards. These
precautions include, but are not limited to, the following:
PRECAUTIONS
PLEASE READ CAREFULLY BEFORE PROCEEDING
* Please keep these precautions in a safe place for future reference.
• Always make sure all batteries are inserted in confor-
mity with the +/- polarity markings. Failure to do so
might result in overheating, fire, or battery fluid leak-
age.
• Always replace all batteries at the same time. Do not
use new batteries together with old ones. Also, do not
mix battery types, such as alkaline batteries with man-
ganese batteries, or batteries from different makers, or
different types of batteries from the same maker, since
this can cause overheating, fire, or battery fluid leak-
age.
Do not dispose of batteries in fire.
• Do not attempt to recharge batteries that are not in-
tended to be charged.
CAUTION
Always follow the basic precautions listed below to avoid the possibility of physical injury to
you or others, or damage to the instrument or other property. These precautions include, but
are not limited to, the following:
• Do not place the AC adaptor cord near heat sources
such as heaters or radiators, and do not excessively
bend or otherwise damage the cord, place heavy ob-
jects on it, or place it in a position where anyone could
walk on, trip over, or roll anything over it.
• When removing the electric plug from the instrument
or an outlet, always hold the plug itself and not the
cord.
• Do not connect the instrument to an electrical outlet
using a multiple-connector. Doing so can result in lower
sound quality, or possibly cause overheating in the
outlet.
• Unplug the AC power adaptor when not using the in-
strument, or during electrical storms.
(4)
2
PRECAUTIONS
PLEASE READ CAREFULLY BEFORE PROCEEDING
* Please keep these precautions in a safe place for future reference.
CAUTION
Always follow the basic precautions listed below to avoid the possibility of physical injury to
you or others, or damage to the instrument or other property. These precautions include, but
are not limited to, the following:
• If the instrument is not to be in use for a long time,
remove the batteries from it, in order to prevent pos-
sible fluid leakage from the battery.
• Keep batteries away from children.
• Before connecting the instrument to other electronic
components, turn off the power for all components. Be-
fore turning the power on or off for all components, set
all volume levels to minimum.
Do not expose the instrument to excessive dust or vi-
brations, or extreme cold or heat (such as in direct sun-
light, near a heater, or in a car during the day) to pre-
vent the possibility of panel disfiguration or damage to
the internal components.
• Do not use the instrument near other electrical prod-
ucts such as televisions, radios, or speakers, since this
might cause interference which can affect proper op-
eration of the other products.
• Do not place the instrument in an unstable position
where it might accidentally fall over.
• Before moving the instrument, remove all connected
adaptor and other cables.
• When cleaning the instrument, use a soft, dry cloth.
Do not use paint thinners, solvents, cleaning fluids, or
chemical-impregnated wiping cloths. Also, do not place
vinyl or plastic objects on the instrument, since this
might discolor the panel or keyboard.
Do not rest your weight on, or place heavy objects on
the instrument, and do not use excessive force on the
buttons, switches or connectors.
Do not operate the instrument for a long period of time
at a high or uncomfortable volume level, since this can
cause permanent hearing loss. If you experience any
hearing loss or ringing in the ears, consult a physician.
REPLACING THE BACKUP BATTERY
• This instrument contains a non rechargeable internal
backup battery which permits internal data to remain
stored even when the power is off. When the backup
battery needs replacing, the message "Backup Batt.
Low" will display in the LCD panel. When this happens,
immediately back up your data (using an external de-
vice such as the floppy disk-based Yamaha MIDI Data
Filer MDF2), then have qualified Yamaha service per-
sonnel replace the backup battery.
Do not attempt to replace the backup battery your-
self, in order to prevent the possible serious hazards.
Always have qualified Yamaha service personnel re-
place the backup battery.
Never place the backup battery in a location that a child
can reach, since a child might accidentally swallow the
battery. If this should happen, consult a physician im-
mediately.
SAVING USER DATA
Save all data to an external device such as the Yamaha
MIDI Data Filer MDF2, in order to help prevent the loss
of important data due to a malfunction or user operat-
ing error.
Yamaha cannot be held responsible for damage caused by
improper use or modifications to the instrument, or data that
is lost or destroyed.
Always turn the power off when the instrument is not in
use.
Make sure to discard used batteries according to local
regulations.
(4)
3
Contents
1: The QY70 — An Overview ............. 5
Sequencer Functions....................... 6
Accompaniment Sequencing .......... 7
Voices & Effects .............................. 8
2: Power & Connections .................... 9
Power Supply ........................................ 9
Using Batteries ................................ 9
When to Replace the Batteries ..... 10
Using a Power Adaptor ................. 11
Setting Up ............................................ 12
The Connectors ............................. 12
Audio Connections ........................ 14
MIDI Connections ......................... 15
Connecting to a Personal
Computer ...................................... 16
About the MIDI Driver ................... 19
3: The Controls ................................. 22
4: Play the Demo Songs .................. 31
5: Easy Accompaniment .................. 33
Selecting & Playing the Preset
Patterns ............................................... 33
Changing Chords ........................... 39
Fingered Chord Function ............... 43
Preset Chord Templates ................ 43
Record a Complete Accompaniment ... 44
Realtime Accompaniment
Recording ...................................... 44
Recording Tempo Changes ........... 50
Step Accompaniment Recording... 51
“Pt” — Step Record Pattern
Changes ........................................ 54
“Cd” — Step Record Chord
Changes ........................................ 57
6: The Song Voice Mode .................. 61
The Effect Send Display ...................... 66
Voice Editing ........................................ 68
Drum Edit ...................................... 72
7: Creating A Complete Song ......... 75
Recording the Sequencer Tracks ......... 75
Preparing to Record
— Voice Assignments ................... 75
Realtime Sequencer Track
Recording ...................................... 76
Step Sequencer Track Recording .. 81
8: Playback Control .......................... 88
Play Effects ..........................................94
Groove Quantization ...................... 96
Drum Table Remapping ................. 98
9: The Song Jobs............................ 101
00 : Undo/Redo .................................. 103
01 : Quantize ..................................... 104
02 : Modify Velocity ........................... 107
03 : Modify Gate Time ....................... 109
04 : Crescendo .................................. 111
05 : Transpose ................................... 113
06 : Shift Clock .................................. 114
07 : Chord Sort .................................. 116
08 : Chord Separate ........................... 117
09 : Copy Event ................................. 118
10 : Erase Event ................................ 120
11 : Extract Event .............................. 121
12 : Create Continuous ...................... 123
13 : Thin Out ...................................... 125
14 : Time Stretch ............................... 126
15 : Create Measure .......................... 127
16 : Delete Measure .......................... 128
17 : Copy Track .................................. 129
18 : Mix Track .................................... 130
19 : Clear Track .................................. 131
20 : Expand Backing .......................... 132
21 : Normalize .................................... 133
22 : Copy Song .................................. 134
23 : Clear Song .................................. 135
24 : Song Name ................................. 136
T h e Q Y 7 0 — A n O v e r v i e w
4
10: Creating Original Accompaniment
Patterns ..................................... 137
The Preset Phrases ........................... 137
Combining Phrases In the Pattern
Mode ................................................. 139
Recording Original Phrases ............... 144
Realtime Phrase Recording ......... 144
Step Phrase Recording ................ 150
Pattern Voice mode ........................... 151
The Effect Send Display .................... 152
Voice Editing ...................................... 154
Play Effects ........................................ 155
11: The Pattern Jobs ...................... 157
00 : Undo/Redo .................................. 159
01 : Quantize ..................................... 160
02 : Modify Velocity ........................... 163
03 : Modify Gate Time ....................... 165
04 : Crescendo .................................. 167
05 : Transpose ................................... 169
06 : Shift Clock .................................. 170
07 : Chord Sort .................................. 172
08 : Chord Separate ........................... 173
09 : Copy Event ................................. 174
10 : Erase Event ................................ 176
11 : Extract Event .............................. 177
12 : Create Continuous ...................... 179
13 : Thin Out ...................................... 181
14 : Time Stretch ............................... 182
15 : Copy Phrase ............................... 183
16 : Get Phrase .................................. 184
17: Put Phrase ................................... 185
18 : Copy Track .................................. 186
19 : Mix Track .................................... 187
20 : Clear Track .................................. 188
21 : Copy Pattern ............................... 189
22 : Clear Pattern ............................... 190
23 : Style Name ................................. 191
12: Editing Songs & Patterns ........ 192
Engaging the SONG or PATTERN
Edit Mode .................................... 192
Moving Around ............................ 195
Change Mode Editing .................. 196
Insert Mode Editing ..................... 197
XG View ............................................. 208
View Filter .......................................... 209
Phrase Table (Pattern Edit Only) ........ 210
13: Effects & Effect Editing ............ 212
Accessing & Editing the Effect
Parameters ........................................ 212
Effect Editing ..................................... 216
14: Utility Functions ....................... 218
Accessing the Utility Mode ......... 218
System Parameters ..................... 220
MIDI Parameters ......................... 222
Bulk Dump ................................... 225
Fingered Zone ............................. 227
15: Appendix ................................... 229
Specifications .................................... 229
Troubleshooting ................................. 231
Error Messages ................................. 233
Glossary ............................................. 235
Index .................................................. 242
Contents
The screen displays as illustrated in this owner’s manual are for
instructional purposes, and may appear somewhat different from
the screens which appear on your instrument.
5
1
T h e Q Y 7 0 — A n O v e r v i e w
T h e Q Y 7 0 — A n O v e r v i e w
The QY70 is a sophisticated music production system with a
16-track sequencer, a high-quality tone generator that provides 519
voices and 20 drum kits, and advanced auto-accompaniment capabil-
ity all integrated in a compact, easy-to-handle package. It also features
a built-in micro-keyboard for easy programming without an external
MIDI keyboard.
Sequencer
QY70
Controller
Tone Generator Effects
• 16 sequencer tracks
• 8 accompaniment
tracks
• built-in micro keyboard
• 519 voices
• 20 drum kits
• reverb, delay,
modulation,
distortion, etc
MIDI messages MIDI messages
Audio
signals
LINE OUT/
PHONES
Audio
signals
MIDI
messages
T h e Q Y 7 0 — A n O v e r v i e w
6
Sequencer Functions
The QY70 sequencer has 16 “normal” sequencer tracks to which
you can individually assign any of the internal voices and record either via
the QY70’s own micro keyboard or an external keyboard connected to the
QY70 MIDI IN connector. In the “replace” real-time record mode the QY70
records exactly what you play as you play it; the “overdub” real-time
record mode lets you add new material to a previously recorded track; and
the step record mode allows notes to be entered one at a time. The step
record mode lets you record extremely fast or complex passages that
would be impossible to play in real time. It’s also useful for adding finishing
touches to tracks recorded in real time. There’s also a “multi” real-time
record mode in which all 16 sequencer tracks can be recorded simulta-
neously.
The QY70 provides an extensive range of advanced editing functions
that make modifying and refining your recorded data an easy, efficient
process.
7
1
T h e Q Y 7 0 — A n O v e r v i e w
Accompaniment Sequencing
The QY70 features a unique accompaiment system that makes it
easy to create complete accompaniments for any type of music. Accompa-
niments are produced by specifying a sequence of “patterns” to be played
rather than by recording individual notes or chords. The QY70 provides 128
preset accompaniment “styles”, and memory for up to 64 original user
“styles” that you can record yourself. Each “style” can have 6 variation
“patterns” — intro, main A, main B, fill AB, fill BA, and an ending — that
you can sequence, along with chord changes, to quickly create complete
accompaniment tracks. Chord changes are programmed simply by entering
the name of the chord — Yamaha’s advanced ABC (Auto Bass Chord) auto-
accompaniment system automatically re-harmonizes the patterns accord-
ingly. The QY70’s accompaniment sequencing features mean you can whip
up a complete accompaniment in a fraction of the time it would normally
take, significantly simplifying and speeding up the overall production
process.
STYLE 001
STYLE 128
INTRO MAIN A MAIN B FILL AB FILL BA ENDING
128 preset accompaniment “styles” each with 6 variation “patterns”
T h e Q Y 7 0 — A n O v e r v i e w
8
Voices & Effects
The QY70’s internal tone generator, compatible with XG and GM
format, provides 519 top-quality voices plus 20 complete drum kits with
different drum and percussion instruments assigned to different notes. You
can assign any of these voices to the sequencer tracks and patterns, or
play them from an external keyboard or other MIDI controller via the MIDI
interface, or directly from a personal computer. The QY70 also features a
high-quality internal DSP (Digital Signal Processor) system which provides a
range of reverb, delay, modulation, distortion and other effects in three
individually programmable groups so you can produce a polished sound
without the need for external equipment.
DETAIL
See the List Book for a complete list of the QY70 voices.
The QY70 effects are described on page 212.
GM(General MIDI) System Level 1
“GM System Level 1” is a standard specification that defines
the arrangement of voices in a tone generator and its MIDI
functionality, ensuring that data can be played back with
substantially the same sounds on any GM-compatible tone generator,
regardless of its manufacturer or model.
Tone generators and song data that meet the “GM System Level 1” bear
this GM logo.
XG
“XG” is a tone generator format that expands the voice
arrangement of the “GM System Level 1” specification to
meet the ever-increasing demands of today’s computer
peripheral environment, providing richer expressive power while maintaining
upward compatibility of data. “XG” greatly expands “GM System Level 1”
by defining the ways in which voices are expanded or edited and structure
and type of effects.
When commercially available song data bearing the XG logo is played back
on a tone generator which bears the XG logo, you will enjoy a full musical
experience that includes unlimited expansion voices and effect functions.
9
2
P o w e r & C o n n e c t i o n s
Using Batteries
Six 1.5V AA size (SUM-3 or R6P) or equivalent batteries must first be
installed in the battery compartment. Alkaline batteries are recommended
for longer life.
Never mix battery types, such as alkaline batteries with manga-
nese batteries or batteries from different makers.
P o w e r & C o n n e c t i o n s
Power Supply
Your QY70 will run either from batteries or an optional AC adaptor.
Follow the instructions below according to the power source you intend to
use.
Z Open Battery Compartment Cover
Open the battery compartment cover — located on the
instrument’s bottom panel — by pressing down on the grooved
section of the cover and sliding in the direction of the arrow, as
shown in the illustration.
X Insert Batteries
Insert the six batteries, being careful to follow the polarity
markings on the bottom panel.
10
P o w e r & C o n n e c t i o n s
C Replace Cover
Replace the compartment cover, making sure that it locks
firmly in place.
When to Replace the Batteries
When the batteries run down and are no longer able to operate the
QY70, the sound may become distorted and the following display will
appear:
When this display appears, replace the batteries with a complete set
of six new batteries. NEVER mix old and new batteries!
CAUTION!
To prevent possible damage due to battery leakage, remove the batteries from the
instrument if it is not to be used for an extended period of time.
11
2
P o w e r & C o n n e c t i o n s
CAUTION!
Do not attempt to use an AC adaptor other than the specified unit or an appropriate
replacement provided by your Yamaha dealer to power the QY70. The use of an
incompatible adaptor may cause irreparable damage to the QY70, and might pose a
serious shock hazard!
Unplug the AC power adaptor when not using the instrument, or during electrical
storms.
Using a Power Adaptor
Plug the DC output cable from a Yamaha PA-3B AC Adaptor (avail-
able from your Yamaha dealer) into the DC IN jack on the rear panel, then
plug the adaptor into a convenient wall AC power socket.
DC IN
P o w e r & C o n n e c t i o n s
PA-3B
AC power
socket.
12
P o w e r & C o n n e c t i o n s
Setting Up
What you will connect the QY70 to, and what you will connect to the
QY70, will depend entirely on your individual requirements, and it would be
impossible to cover all possibilities here. A few examples are provided
below to help you get started.
The Connectors
q DC IN Jack
This jack is only used when you are powering the QY70
from an optional AC adaptor instead of batteries. The DC output
cable from an optional Yamaha PA-3B AC Power Adaptor is
plugged in here.
NOTE
The batteries are automatically disconnected when a plug is inserted
into the DC IN jack.
w qr e
r
Rear Panel
Right Side Panel
13
2
P o w e r & C o n n e c t i o n s
w MIDI IN & OUT Connectors
If you plan to use a MIDI keyboard or other instrument to
play and program the QY70, it should be connected to QY70
MIDI IN connector (see “MIDI Connections,” on page 15). The
MIDI OUT connector can be connected to an external tone
generator if you want to drive external voices from the QY70
sequencer, or a MIDI data recorder such as the Yamaha MDF2 if
you want to store your songs and patterns to floppy disk (page
225).
e LINE OUT/PHONES Jack
This miniature stereo phone jack can be used to connect
the output of the QY70 to a stereo sound system, or a pair of
stereo headphones with a miniature stereo phone plug can be
plugged in here for convenient monitoring (see “Audio Connec-
tions,” on page 14). The output level is adjusted via the VOLUME
control on the left side panel.
r TO HOST Connector & HOST SELECT Switch
This jack and selector switch (the switch is on the side
panel) allow direct connection to a personal computer without the
need for a separate MIDI interface. See “Connecting To a Per-
sonal Computer” on page 16 for details.
14
P o w e r & C o n n e c t i o n s
Audio Connections
The simplest way to monitor the QY70 sound is via a pair of stereo
headphones (miniature stereo phone plug type) plugged into the LINE
OUT/PHONES jack. If you want to use an external stereo sound system,
however, use the supplied “Y” cable (miniature stereo phone plug to dual
RCA pin plugs) to connect the LINE OUT/PHONES jack to the inputs of a
stereo sound system. The white RCA pin plug goes to the left-channel
input of your stereo sound system and the red plug goes to the right-
channel input.
LINE OUT /
PHONES
LR
CAUTION!
Make sure that both the QY70 and your sound system are turned OFF when
making connections.
Stereo Sound System
15
2
P o w e r & C o n n e c t i o n s
MIDI Connections
Although the QY70 can be played and programmed from the built-in
micro-keyboard, an external MIDI keyboard connected to the MIDI IN
connector provides the added advantages of standard keyboard size and
key velocity sensivity (if your keyboard has a velocity-sensitive keyboard).
Connect the MIDI OUT connector of the keyboard to the MIDI IN connec-
tor of the QY70, and make sure that the QY70 HOST SELECT switch is set
to MIDI. The connected MIDI keyboard will play the voice assigned to the
currently selected sequencer track. See page 61 for instructions on how to
assign different voices to the sequencer tracks.
External MIDI Keyboard
OUT
——
MIDI
——
IN
MIDI OUT
(HOST SELECT switch
is set to MIDI)
16
P o w e r & C o n n e c t i o n s
Connecting to a Personal Computer
Although the QY70 can be connected to a personal computer via the
MIDI IN/OUT connectors and a MIDI interface, the TO HOST connector
and selector switch allow direct connection to Apple Macintosh, IBM-PC/
AT, or NEC PC-9801/9821 series personal computers for sequencing and
other music applications without the need for a separate MIDI interface.
IMPORTANT!
If the QY70 is to be connected to a computer via the TO HOST connector and a
MIDI controller via the MIDI IN connector, the “echo back”(or “MIDI Thru” etc)
function of the music software or sequencer you are using must be turned “on” so
that the MIDI note data from the controller is returned to the QY70 and any
subsequent devices connected to the QY70 MIDI OUT connector.
TO HOST
QY70
MIDI
OUT
MIDI
IN
MIDI IN
MIDI OUT
MIDI Controller
(MIDI Keyboard etc)
Personal Computer
echo back = ON
Tone Generator
17
2
P o w e r & C o n n e c t i o n s
Connecting to an Apple Macintosh Series Computer
Connect the TO HOST connector of the QY70 to the
modem or printer port on your Macintosh, depending on which
port your MIDI software is using for MIDI data communication,
using a standard Macintosh 8-pin system peripheral cable. Set
the HOST SELECT switch to the “Mac” position.
You may also have to make other MIDI interface settings
on the computer side, depending on the type of software you
use (refer to your software owner’s manual). In any case the
clock speed should be set to 1 MHz.
“Mac” Cable Connections
Connecting to an IBM-PC/AT Series Computer
Connect the TO HOST connector of the QY70 to the RS-
232C port on your IBM computer, using a standard 8-pin MINI
DIN
9-pin D-SUB cross cable. Set the HOST SELECT switch to
the “PC-2” position.
Refer to your software owner’s manual for information on
any settings you might have to make on the computer side.
“PC-2” Cable Connections
8-pin system peripheral cable.
Data transfer rate: 31,250 bps.
8-pin mini DIN
9-pin D-SUB cable. Use a “PC-1” type cable if your
computer uses a 25-pin serial port.
Data transfer rate: 38,400 bps.
2 (HSK i)1
1 (HSK 0)2
5 (RxD-)3
MINI DIN
8-PIN
4 GND4
3 (TxD-)5
8 (RxD+)6
7 (GP i)7
6 (TxD+)8
MINI DIN
8-PIN
Modem or
printer port
TO HOST
connector
8 (CTS)1
7 (RST)2
2 (RxD)3
4 5 (GND)
8
3 (TxD) 5
MINI DIN
8-PIN
D-SUB
9-PIN
RS-232C
port
TO HOST
connector
18
P o w e r & C o n n e c t i o n s
Connecting to an NEC PC-9801/9821 Series Computer
The NEC PC-9801/9821 computers are widely used in
Japan. Connect the TO HOST connector of the QY70 to the RS-
232C port on your NEC computer, using a standard 8-pin MINI
DIN
25-pin D-SUB cross cable. Set the HOST SELECT switch
to the “PC-1” position if you use Windows3.1, and to the “PC-2”
position if you use Windows95.
Refer to your software owner’s manual for information on
any settings you might have to make on the computer side.
“PC-1” Cable Connections
8-pin mini DIN
25-pin D-SUB cable. Use a “PC-2” type cable if your
computer uses a 9-pin serial port.
Data transfer rate: 31,250 bps.
NOTE
If your system doesn’t work properly with the connections and settings
listed above, your software may require different settings. Check your
software operation manual and set the HOST SELECT switch to the
position provides the appropriate data transfer rate.
If you use Windows95 or Windows3.1 in your computer, the appropri-
ate “MIDI driver” needs to be installed. See page 19 for details.
MINI DIN
8-PIN
D-SUB
25-PIN
5 (CTS)1
4 (RTS)2
3 (RxD)3
4 7 (GND)
8
2 (TxD) 5
RS-232C
port
TO HOST
connector
19
2
P o w e r & C o n n e c t i o n s
About the MIDI Driver
If you use Windows95 or Windows3.1 in your computer, the appro-
priate “MIDI driver” needs to be installed.
First connect your QY70 to the computer via the TO HOST jack as
shown above, and install the Yamaha CBX Driver for Windows95 (if you
use Windows95) or the Yamaha CBX-T3 Driver (if you use Windows3.1)
from the supplied floppy disk labelled “QY Data Filer” as follows.
(For details about each MIDI driver, refer to the “Readme” file
contained within each MIDI driver’s folder in the floppy disk.)
Installing the Yamaha CBX Driver for Windows95
Z Insert the floppy disk labelled “QY Data Filer for Windows”
into the floppy disk drive.
X Double click “Add New Hardware” in the Control Panel.
The “Add New Hardware Wizard” will appear.
C Click “Next”.
V When you are asked if you want to auto-detect the new
hardware, click “No” and then click “Next”.
B In the hardware screen choose “Sound, Video and Game
Controllers” and click “Next”.
N Click the “Have Disk” button.
M Type in the name of the floppy disk drive where the floppy
disk is inserted, and the name of the directory containing the
driver. After that, click “OK”.
For example, if you inserted the disk in drive A,
you should type as follows:
A:\MIDIDRV
If you inserted the disk in drive B, you should type
as follows:
B:\MIDIDRV
20
P o w e r & C o n n e c t i o n s
< In the “Select Device” screen you will see “Yamaha CBX
Driver for Windows95”. Click “OK”.
> Click “Finish”.
? The “YAMAHA CBX Driver Setup” dialog box appears after
the drivers are finished copying. Choose the desired COM port
and click “OK”. (The QY70 doesn’t support the Multi-port
feature) The “Do you want to restart Windows?” dialog will
appear.
[ Remove the floppy disk and click “OK” to activate the new
driver.
This completes installation of the MIDI driver.
Remember to set the Host Select switch to PC-2 when
you connect your QY70 to an IBM-PC/AT series or NEC PC-9801/
9821 series computer.
Z Insert the floppy disk labelled “QY Data Filer for Windows”
into the floppy disk drive.
X Double click the “Control Panel” icon typically found in the
Main Group of the Program Manager window.
The Control Panel window will appear.
C Double click the “Drivers” icon in the Control Panel window.
The “Drivers” dialog box will appear.
V Click the “Add” button. The “Add” dialog box will appear.
B Select “Unlisted or Updated Driver” from the list box and click
“OK”.
The “Install Driver” dialog box will appear.
Installing the Yamaha CBX-T3 Driver (for Windows3.1)
21
2
P o w e r & C o n n e c t i o n s
Click “OK”.
The “Add Unlisted or Updated Driver” dialog box will
appear.
M With the “Yamaha CBXT3 Serial Driver” highlighted, click
“OK”.
The “Yamaha CBX-T3 Serial Driver Setup” dialog box will
appear.
< Click the desired COM port to select it, then click “OK”.
The System Setup dialog box will appear.
> Click “Restart” to make the added driver effective.
This completes installation of the MIDI driver.
Remember to set the Host Select switch to PC-2 when
you connect your QY70 to an IBM-PC/AT series, or PC-1 when
you connect to an NEC PC-9801/9821 series.
For example, if you inserted the disk in drive A of
an IBM-PC/AT series computer, you should type as
follows:
A:\IBMPC
If you inserted the disk in drive B of an NEC PC-
9801/9821 series, you should type as follows:
B:\NECPC98
N Type in the name of the floppy disk drive where the floppy
disk is inserted, and the name of the directory containing the
driver.
22
T h e C o n t r o l s
T h e C o n t r o l s
The QY70 has fairly simple, consistent control interface that,
once understood, makes operation fast and easy, no matter what
operation you are performing. If you read through this section care-
fully, and try out the procedures in the␣ ”TRY THIS” sections, you
should have no problem accessing and operating the QY70’s many
advanced features.
q !4
w
Left Side Panel
Rear Panel
23
3
T h e C o n t r o l s
q POWER Switch
Slide to the “ON” position to turn the QY70 on, or to the
“OFF” position to turn it off.
w LCD Display & CONTRAST Control
This large multi-function liquid crystal display panel shows
all parameters and prompts you need to operate the QY70 with
optimum ease and efficiency.
Use the CONTRAST control on the rear panel to achieve
the best display visibility (LCD visibility varies greatly with viewing
angle and lighting).
e [SONG] Key
Use this key to select the QY70 SONG mode from any
other mode, and to switch between the SONG, SONG VOICE,
and SONG EFFECT displays.
et yr w o
!1
!3
!0
i
!2
u
Front Panel
24
T h e C o n t r o l s
TRY THIS:
Turn your QY70 on (the
power switch is on the
left side), then press the
[SONG] key a few times
and watch how the
display changes. The
[SONG] key calls the
SONG, SONG VOICE,
and SONG EFFECT
displays in sequence.
The order in which the
displays is selected is
reversed if you press the
[SONG] key while
holding the [SHIFT] key.
r [PATT] Key
The [PATT] key selects the QY70 PATTERN mode from any
other mode, and switches between the PATTERN, PATTERN
VOICE, and PATTERN EFFECT displays.
t [SHIFT] Key
The [SHIFT] key modifies the the function of certain other
keys in certain situations (e.g. it reverses the order in which the
[SONG] or [PATTERN] displays are selected, as described above).
It also allows direct numeric entry via the black micro-keyboard
keys (numbered 1 through 0). Situations in which the [SHIFT] key
can be used will be described where appropriate in the manual.
SONG EFFECT display
SONG VOICE display
SONG display
25
3
T h e C o n t r o l s
y [EXIT] Key
No matter where you are in the QY70 display hierarchy, the
[EXIT] key will take to the next highest level (effectively “backing
up” one step — unless you’re already at the top display).
u Cursor Keys
These 4 keys move the “cursor” around the display
screen, highlighting the various parameters that are available for
editing (the QY70 cursor appears as a dark block with inverse
characters).
TRY THIS:
Select the SONG mode display (use the [SONG] key, as
described above), then try using the cursor keys to move
the cursor around the screen.
i [-1/NO] and [+1/YES] Keys
These keys are used to edit (change the value of) the
parameter at which the cursor is currently located. The [-1/NO]
key decrements (decreases stepwise) the value of the selected
parameter, while the [+1/YES] key increments (increases
stepwise) the parameter. Press either key briefly to decrement or
increment the parameter by one, or hold the key for continous
decrementing of incrememnting in the specified direction.
The [-1/NO] and [+1/YES] keys are also used to respond to
“Are you sure?” prompts when they appear. Press [+1/YES] to
go ahead with the operation, or [-1/NO] to cancel.
NOTE
For even faster decrementing or incrementing, press the opposite
increment/decrement key while holding the key corresponding to the
direction you want to increment/decrement in.
TRY THIS:
Select the SONG mode display (use the [SONG] key, as
described above), use the cursor keys to select the trans-
pose parameter (“TRNS” on the display), then try using the
[-1/NO] and [+1/YES] keys to change its value. Set it back
to “+00” before continuing.
26
T h e C o n t r o l s
o [MENU] and Function Keys
The [MENU] key calls a menu of functions or sub-modes
that can be accessed from the current QY70 mode, and the
function keys (the four small keys to the right of the display)
select the corresponding item from the menu that appears on the
display.
The function keys can also be used, as shown below, with
the [SHIFT] key, instead of calling a menu with the [MENU] key.
Pressing the bottom function key while holding the [SHIFT]
key executes the Undo/Redo job for immediately previous
edit. (Refer to “Undo/Redo” on page 103).
Pressing the second
function key while
holding the [SHIFT] key
calls the Used Memory
display.
Pressing the top function
key while holding the
[SHIFT] key calls a
display showing drum
instrument assignments
to each micro keyboard
key at the current octave
setting.
Assignment to black keys
Assignment to white keys
27
3
T h e C o n t r o l s
TRY THIS:
Select the SONG mode display
(use the [SONG] key, as described
above), then press the [MENU]
key. You should see the menu
shown on the right:
Next press the second function key (the one immediately
to the right of “Job” on the menu) to call the SONG mode
Job List:
You can now use the cursor keys
(up and down only) to select the
various items in the Job List.
Leave the display as it is for now,
and read about the [ENTER] key,
below.
!0 [ENTER] Key
In addition to “entering” chords in the SONG and PAT-
TERN modes (which we’ll learn about later), the [ENTER] key is
used to “enter” a selected menu function.
TRY THIS:
Assuming that you’ve gone through the “TRY THIS:”
procedure for the [MENU] and Function keys, above, you
should now have the SONG mode Job List on your QY70
screen. Use the cursor keys (up
and down only) to select job
number 02 “Modify Velocity”.
Now press the [ENTER] key to
actually engage the Modify
Velocity job — the display should
look like this:
Since we don’t really want to use the Modify Velocity job,
press the [EXIT] key twice (or the [SONG] key once) to go
back to the SONG mode.
28
T h e C o n t r o l s
!1 Sequencer Keys
The sequencer keys control recording and playback in the
SONG and PATTERN modes, and allow you to locate a specific
measure within a song or pattern. Their layout and functions are
similar to the transport controls on a tape recorder.
[
S
] RECORD READY: Press this key to engage the record
ready mode. You have to press the START key to
actually start recording.
[
A
] STOP: Press to stop recording or playback.
[
W
] START: Press to start recording or playback.
[
U
] GO TO TOP: This key takes you directly to the first
measure (the “top”) of the current song or pattern.
[
E
] MOVE BACK: Press briefly to move back one mea-
sure, or hold for continuous scrolling.
[
R
] MOVE FORWARD: Press briefly to move forward one
measure, or hold for continuous scrolling.
!2 Micro Keyboard
This tiny 2-octave keyboard makes it possible to program
the QY70 anywhere, anytime, without having to connect an
external MIDI keyboard. It’s even polyphonic, so you can directly
enter chords as well as single notes. The only thing it lacks is
velocity sensitivity. The QY70 does, however, accept velocity
information from an external MIDI keyboard.
When programming accompaniment tracks the micro-
keyboard is also used to specify the chord roots and types to be
entered.
TRY THIS:
In the SONG mode, use the cursor
keys to place the cursor at the
track 1 position (“1” on the
display).
29
3
T h e C o n t r o l s
Now play the micro keyboard. You should hear the voice
that is currently assigned to sequencer track 1.
In the SONG mode, the micro keyboard plays the voice
assigned to the currently selected track (unless you’re
recording the chord track, in which case it is used to
specify chords).
!3 Octave Keys
Since the 2-octave range of the micro-keyboard is not
enough for serious music programming, the [OCT DOWN] and
[OCT UP] keys allow the pitch of the keyboard to be shifted up or
down in octave steps, over a range of 8 octaves. Each time the
[OCT DOWN] key is pressed the pitch of the keyboard is shifted
down by one octave, until the lower limit is reached. The [OCT
UP] key shifts the pitch of the keyboard up in the same way. The
number of octaves the pitch of the micro-keyboard has been
shifted down or up is shown by the octave indicator in the upper
left corner of the display — the number of arrows indicates the
number of octaves shifted in the corresponding direction.
Pressing the [OCT DOWN] and [OCT UP] keys simulta-
neously shifts the pitch to ±0.
When recording the accompaniment chord tracks in the
step mode, the [OCT DOWN] key is used to specify the bass
note for chords, while the [OCT UP] key is used to enter synco-
pated chords.
While playing a note on the micro-keyboard, the [OCT
DOWN] key will shift the pitch of the note up while held, and the
[OCT UP] key will apply modulation while held.
Octave indicator
30
T h e C o n t r o l s
!4 VOLUME Control
The VOLUME control adjusts the volume of the sound
delivered via the LINE OUT/PHONES jack. Slide the control
toward “MAX.” to increase the volume or toward “MIN.” to
decrease the volume.
CAUTION!
Set the VOLUME control to “MIN.” when connecting the QY70 to a
sound system for the first time, then gradually raise the volume level
until the required listening level is reached. This simple precaution can
prevent unexpectedly high volume levels from damaging your speaker
system (and maybe even your ears!).
31
3
T h e C o n t r o l s
P l a y t h e D e m o S o n g s
After you’ve set up and made all necessary connections, you
might like to play back the QY70 demo songs to hear a few examples
of what it can do:
Z Select the SONG Mode
If not already selected, press the [SONG] button to select
the main SONG mode display (depending on the current mode
you may have to press the [SONG] button more than once).
Song number 21, 22, or 23
X Select a Demo Song
Use the cursor keys to move the cursor to the song
number, then use the [-1] and [+1] keys to select one of the
demo songs: song number 21, 22, or 23.
4
32
P l a y t h e D e m o S o n g s
C Start Playback
Press the sequencer [
W
] key to start playback. Use the
VOLUME control to set the optimum listening level.
V Stop Playback
Although playback will stop automatically when the current
song is finished, you can stop playback at any time by pressing
the sequencer [
A
] key to stop playback.
33
5
E a s y A c c o m p a n i m e n t
E a s y A c c o m p a n i m e n t
Using the QY70 preset patterns you can easily create accom-
paniments that you can play or sing along with. You can also add
melody tracks later to create complete compositions.
NOTE
In addition to the preset patterns, the QY70 has memory for 384 original
patterns (i.e., 64 user accompaniment “styles” x 6 variation patterns) which
you can create as described in “Creating Original Accompaniment Patterns”,
beginning on page 137.
Z Select the SONG Mode and an “Empty” Song
First use the [SONG] key to select the main SONG mode
display. In order to select and play the patterns as described in
this section you must select an empty song (i.e. one in which
nothing has been recorded). Different song numbers (1 through
20) are selected simply by moving the cursor to the song number
and using the [-1] and [+1] keys (or use the SHIFT-Number entry
method described below).
Selecting & Playing the Preset Patterns
The QY70 has 128 preset accompaniment styles, each containing 6
variation patterns, that cover a wide variety of musical patterns. Here’s
how you can select and play the patterns while in the SONG mode.
34
E a s y A c c o m p a n i m e n t
The SHIFT-Number Entry Method
Numeric values can be directly entered by using the black
micro-keyboard keys (numbered 1 through 0) while holding
the shift key. To enter the number “16”, for example,
press the “1” and then the “6” keys (“F#/Gb” and “7
(#9)
/
7
(b9)
” on the micro-keyboard) while holding the [SHIFT]
key. The entered number — “16” — will flash on the
display. Press the [ENTER] key to actually enter the num-
ber.
Song number (1 … 20)
35
5
E a s y A c c o m p a n i m e n t
In cases in which a negative number needs to be entered
(a TRANSPOSE value, for example) press the leftmost
micro-keyboard key — the lowest “E” key — to switch
between “+” and “-” values before entering the number.
X Select a Style Number
Use the cursor keys to move the cursor to the accompani-
ment style number, then use the [-1] and [+1] buttons or the
SHIFT-Number entry method to select the style you want to play.
The preset styles are numbers 001 through 128.
C Start Playback
Press the [
W
] key to start playback of the selected accom-
paniment style. The green LED above the [
W
] key will flash at the
current playback tempo.
Note that the measure number on the display advances as
each measure is played.
Style
number
Measure
number
36
E a s y A c c o m p a n i m e n t
V Listen to the Style’s Variation Patterns
Each preset style has 6 variation patterns or “sections” —
INTRO, MAIN A, MAIN B, FILL AB, FILL BA, and ENDING.
There’s also a “BLANK” section that can be used to create
breaks.
INTRO ........ introduction
MAIN A...... normal pattern, used for the “verse” of a
song.
MAIN B . .... variation, normally used as a chorus or bridge.
FILL AB ...... fill-in transition from MAIN A to MAIN B.
FILL BA ...... fill-in transition from MAIN B to MAIN A.
ENDING ..... ending pattern.
BLANK ....... silent pattern for “breaks”.
When the INTRO, FILL AB, and FILL BA sections are
selected while playing a pattern in the SONG mode, the section
plays through once and is automatically followed by either the
MAIN A or MAIN B section. INTRO is followed by MAIN A, FILL
AB is folowed by MAIN B and FILL BA is followed by MAIN A.
The FILL AB and FILL BA sections automatically provide smooth,
“musical” transitions between the MAIN A and MAIN B sections.
Playback stops automatically after the ENDING section.
The currently selected section is shown between square
brackets below the style number and name.
Currently selected section
37
5
E a s y A c c o m p a n i m e n t
You can change sections directly by pressing the appropri-
ate key on the micro-keyboard while the cursor is located at
either the style number or the section name on the display.
The newly selected section will begin playing from the top
of the next measure. “NEXT” will appear below the style number
until the new section actually begins playing.
NOTE
You can also change sections by placing the cursor over the section
name and using the [-1] and [+1] keys.
“NEXT”
38
E a s y A c c o m p a n i m e n t
B Select Different Styles & Patterns (Sections)
With the cursor positioned over the style number you can
use the [-1] and [+1] keys to select different styles, and use the
micro-keyboard section keys to select different patterns (sec-
tions) during playback. In all cases the newly selected style or
pattern (section) will begin playing from the top of the next
measure. “NEXT” will appear below the style number until the
new style or pattern (section) actually begins playing.
NOTE
If you move the cursor to the tempo parameter (indicated by a note
symbol and a number in the upper left corner of the display), you can
use the [-1] and [+1] buttons or the SHIFT-Number entry method to set
the playback tempo to anywhere from 25 to 300 beats per minute.
N Stop Playback When Done
Stop playback at any time by pressing the [
A
] key. For a
more musical ending, select the ENDING section. Playback will
stop automatically after the ENDING section.
Tempo
39
5
E a s y A c c o m p a n i m e n t
Z Play a Pattern
Select and play one of the preset patterns, as described in
the preceding section.
X Move the Cursor to the Chord Symbol
The micro-keyboard can be used to enter chords only
when the cursor is located over the chord symbol on the display.
Use the cursor keys to move the cursor to the chord symbol at
the bottom of the display.
Changing Chords
The QY70 features a sophisticated ABC (Auto Bass Chord) system
that automatically re-harmonizes the accompaniment to match chords you
specify. This makes creating complete accompaniment tracks fast and
easy … just select a pattern, then specify the required chord changes
(details in the next section). Here’s how you use the micro-keyboard to
specify chord changes.
The following procedure can be performed when “FNGR”(Fingered
Chord function) is set to “OFF”. First of all, confirm that FNGR is “OFF”
before changing chords as follows. (For details on the Fingered Chord
function, see page 43 and 227.)
Chord symbol
Fingered chord
function ON/OFF
40
E a s y A c c o m p a n i m e n t
To enter a chord, press the key corresponding to the
desired chord root, then the key corresponding to the desired
chord type (the chord type keys alternately select the lower and
upper chord types marked … watch the display), and finally the
[ENTER] key.
C Enter a Chord
Note that the lower octave of the micro-keyboard has
chord root names “E” through “D#/Eb” marked on the keys, and
the upper octave keys are marked with a variety of chord types.
Example: Enter a G7 Chord
41
5
E a s y A c c o m p a n i m e n t
The chord is actually entered only when the [ENTER] key is
pressed. Until the [ENTER] key is pressed, the newly specified
chord root and type will flash on the display.
NOTE
Actually, you can press the chord type key and then the root key, the
order doesn’t matter.
The Chord Types
add9 added ninth.
M major.
M7(9) major seventh ninth.
M7 major seventh.
aug augmented.
6 sixth.
7(9) seventh ninth.
7 seventh.
add9 minor added ninth.
m minor
m7(9) minor seventh ninth.
m7 minor seventh.
mM7 minor major seventh.
m6 minor sixth.
m7(11) minor seventh added eleventh.
m7(b5) minor seventh flatted fifth.
7(#9) seventh sharp ninth.
7(b9) seventh flatted ninth.
7(b13) seventh added flatted thirteenth.
7(13) seventh added thirteenth.
7(#11) seventh added sharp eleventh.
7(#5) seventh sharp fifth.
7sus4 seventh suspended fourth.
sus4 suspended fourth.
-
-
- non-ABC (see “NOTE” below).
dim diminished.
NOTE
The “-
-
-” chord type marking is a special “non-ABC” type that can be
used to transpose accompaniment patterns to the selected chord root
without re-harmonization.
If you enter only the chord root without a chord type, the preceding
chord type will be retained. In the same way the root of the preceding
chord will be retained if only the chord type is entered.
42
E a s y A c c o m p a n i m e n t
V Try Out the Various Chords with Different Patterns
During playback you can move the cursor up to the style
number, select a different pattern (section), then move the cursor
back to the chord symbol and try different chords with the new
pattern.
NOTE
If you move the cursor to the “TRNS” (transpose) parameter, you can
use then [-1] and [+1] buttons or the SHIFT-Number entry method to
transpose the pitch of the entire pattern up or down in semitone
increments over a range of two octaves (-24 through +24). A transpose
setting of “+00” produces normal pitch.
B Stop Playback When Done
Stop playback by pressing the [
A
] key. You can also stop
playback after an appropriate ending by selecting the ENDING
section (the cursor must be on the style number or section name
to do this).
TRNS
parameter
NOTE
ENDING and INTRO patterns for each preset style have their own
chord progressions which means chord types (major, minor, etc.)
selected will be ignored. (i.e., preset ENDING and INTRO patterns will
simply be transposed to the selected chord root without re-harmoniza-
tion.)
43
5
E a s y A c c o m p a n i m e n t
Preset Chord Templates
The QY70 also features preset chord progression templates that can
re-harmonize the accompaniment patterns to match preset chord progres-
sions.
This is useful when you practice playing along with or studying the
“typical”chord progressions for a variety of musical genres.
To use this template, move the cursor to “USR” to the right of the
chord symbol and select the template using the [+1] and [-1] buttons or the
SHIFT-Number entry method. The preset chord template list is on the List
Book.
Fingered chord
function
Fingered Chord Function
Chords can also be changed by playing the chord, as it is, on the
micro keyboard or an external MIDI keyboard. To enter the chord in this
method, turn the “FNGR”(Fingered Chord function) to “ON”.
You do not need to press [ENTER] for the newly entered chord using
this procedure.
Chord template
NOTE
The preset chord templates will repeatedly play chord progressions until the [
A
] key
is pressed.
The preset chord templates can be stored as a user chord progression by executing
the “Copy Event” job on page 118.
The preset chord templates can not be played properly in other than 4/4 time
signature songs, since these templates have been programmed for 4/4 songs. To
play a template properly in the non-4/4 songs, execute the “Copy Event” job to
copy it to “USR”, then edit the chord (Cd) track.
44
E a s y A c c o m p a n i m e n t
Z Select the SONG Mode & an Empty Song
Use the [SONG] key to select the main SONG mode
display and, with the cursor located over the song number at the
top of the display, use the [-1] and [+1] keys or the SHIFT-Number
entry method to select an empty song number if necessary.
Realtime Accompaniment Recording
Once you know how to select patterns (i.e., styles and sections) and
enter chords in the SONG mode (see the preceding sections), recording a
basic accompaniment in real time is easy. Tempo changes can be added
later (page 50).
Record a Complete Accompaniment
The QY70 provides two ways to record an accompaniment by
specifying patterns and chords: “realtime” and “step” recording. The
realtime method is the fastest and easiest, letting you record pattern and
chord changes “on the fly.” The step method gives you more detailed
control, and is an excellent way to add the finishing touches to an accom-
paniment recorded in real time.
NOTE
If for some reason all 20 songs contain data, use the “Clear Song”
function described on page 135 to clear a song for recording.
X Select the “Pt” Track to Record Pattern Changes
Move the cursor to the track area of the display, and then
shift the cursor sideways to select “Pt.” Once selected, move
the cursor vertically to move to other areas of the screen. The
selected track will remain highlighted no matter where you move
the cursor.
45
5
E a s y A c c o m p a n i m e n t
C Engage the Record Ready Mode
Press the [
S
] key to engage the record ready mode. The
red LED above the [
S
] key will light. The record mode selectors
will appear in the central area of the display, and the name of the
current record mode will appear at the top of the display.
V Select the Realtime Replace Record Mode
Move the cursor to the record mode selector area of the
display (the area with the “REPL”, “OVER”, “STEP”, and
“MULTI” buttons), and move it to the “REPL” (realtime replace)
button, then press the [+1/YES] key to select the realtime replace
record mode (if it isn’t already selected). An inverse “R” will
appear in the selected record mode button.
“Pt” track
Record mode
selector
46
E a s y A c c o m p a n i m e n t
B Select the Starting Pattern, Chord, & Tempo
Move the cursor to the style number, section, chord, and
tempo parameters, and set as required.
NOTE
It’s sometimes easier to set a slow tempo for realtime recording, so
you have plenty of time to enter pattern and chord changes.
Selected record
mode button
N Record
Press the [
W
] key to begin recording pattern changes. The
metronome will sound and you’ll be given a one-measure count-
in prior to the first measure actually recorded (the number of
count-in measures can be set from 1 to 8 in the Utility mode —
page 220). The count-in is also indicated by negative numbers in
the measure number display. If the number of count-in measures
is “1” (the default setting), for example, “-01” will appear during
the count-in, then recording will begin from measure “001”.
Tempo
47
5
E a s y A c c o m p a n i m e n t
Count-in
Since you selected “Pt” track recording, the cursor will
automatically move to the style number when you start record-
ing. All you have to do to record pattern changes is to select the
required style numbers via the [-1] and [+1] keys or the SHIFT-
Number entry method, and section changes via the appropriate
micro-keyboard keys. Remember that all pattern changes occur
from the top of the next measure after the change is entered.
Also keep in mind that the INTRO will automatically switch to the
MAIN A pattern, FILL AB will automatically switch to the MAIN B
pattern, and FILL BA will automatically switch to the MAIN A
pattern.
You should end your accompaniment track by entering
either the ENDING section or the QY70 “End Pattern” (style
number 129), otherwise your accompaniment will play back
indefinitely.
M Stop Recording
Stop recording by pressing the [
A
] key. The normal SONG
play mode is automatically re-selected when you stop recording.
48
E a s y A c c o m p a n i m e n t
“Cd” track
> Record
Press the [
W
] key to begin recording chord changes. The
metronome will sound and you’ll be given a one -measure count-
in.
< Engage Record Ready Again and Select “Cd”
Press the [
S
] key to engage the record ready mode again
(the “REPL” mode will still be selected), then move the cursor to
the track section of the display and select “Cd” in order to record
chord changes.
Since you selected “Cd” recording, the cursor will auto-
matically move to the chord when you start recording. All you
have to do to record chord changes is to enter the required
chords as described in the “Changing Chords” section (page 39).
49
5
E a s y A c c o m p a n i m e n t
NOTE
Chord changes actually occur on quarter-note divisions, so try to press
the [ENTER] key to enter each chord either exactly on the beat or a
fraction of a section before the beat on which you want the chord
change to occur. Syncopated chord changes can be programmed in the
STEP record mode (page 59).
If the Fingered Chord function(FNGR) is previously set
to“ON”, a chord change can be entered by playing the chord as it
is on the micro keyboard or an external MIDI keyboard. In this
case, you do not need to press [ENTER] for the newly entered
chord.
? Stop Recording
Press the [
A
] key to stop recording when all the required
chord changes have been entered. The normal SONG play mode
is automatically re-selected when you stop recording.
[ Listen To the Results
Press the [
W
] key to play back and check out the accompa-
niment you’ve just recorded.
NOTE
Note that the chord currently playing is shown in the chord symbol
location on the display.
Don’t worry if you’ve made a few mistakes. Simple slip-ups made in
the realtime record mode can usually be corrected in the step record
mode … described next.
50
E a s y A c c o m p a n i m e n t
Recording Tempo Changes
If you want your accompaniment to include tempo changes, they
can easily be added after the pattern and chord changes have been re-
corded: Select the “Tm” (Tempo) track, press the [
S
] button to engage the
record ready mode (only realtime replace recording can be selected for the
tempo track), press [
W
] to start recording (the cursor will automatically
move to the tempo parameter), then use the [-1/NO] and [+1/YES] keys or
the SHIFT-Number entry method to make the required tempo changes in
real time. Press [
A
] to stop recording.
NOTE
Tempo changes can be edited in detail as described in “Editing Songs and
Patterns”, beginning on page 192.
You should record tempo data with this method at the top of the song to fix the
song’s beginning tempo, if you want to add tempo changes.
“Tm” track
51
5
E a s y A c c o m p a n i m e n t
Z Select a Song to Record
Select an empty song if you want to record a new song in
the step record mode, or select a song that already contains data
if you want to make changes or additions.
X Engage the Record Ready Mode
Press the [
S
] key to engage the record ready mode. The
red LED above the [
S
] key will light.
Step Accompaniment Recording
The STEP record mode can be used with the “Pt” (Pattern) and
“Cd” (Chord) tracks, making it easy to individually enter or delete pattern
and chord changes at precisely the required locations.
C Select the “Pt” or “Cd” Track
Move the cursor to the track area of the display, and then
shift the cursor sideways to select “Pt” or “Cd”. Once selected,
move the cursor vertically if you want to move to other areas of
the screen. The selected track will remain highlighted no matter
where you move the cursor.
“Pt” or
“Cd” Track
52
E a s y A c c o m p a n i m e n t
V Select the Step Record Mode
Move the cursor to the record mode selector area of the
display (the area with the “REPL”, “OVER”, “STEP”, and
“MULTI” buttons), and move it to the “STEP” button, then press
the [+1/YES] key to select the step record mode. An inverse “R”
will appear in the selected record mode button.
“STEP” button
B Start Recording
Press the [
W
] key to call the selected step record display.
“Pt” step record “Cd” step record
53
5
E a s y A c c o m p a n i m e n t
N Enter the Required Pattern and/or Chord Data
Refer to the following sections for details on how to use
each of the step-record mode data-entry displays.
You can switch directly between the pattern and chord
data-entry displays while the step record mode is engaged simply
pressing the [MENU] key to call the menu shown below, and
then the function key corresponding to the display you want to
go to.
M Stop Recording
Press the [
A
] key to exit from the step record mode and
return to the normal SONG play mode.
54
E a s y A c c o m p a n i m e n t
“Pt” — Step Record Pattern Changes
Here’s how the STEP record pattern display will look if you’ve
selected an empty song (the appropriate pattern data will appear if the
selected song contains data).
Measure number
Time signature
1st measure
2nd measure
Subsequent measures follow
Style number area
Section area
Moving Around & Entering Data
As usual, the cursor keys are used to move the cursor to
the location at which you want to enter data, and the [-1] and [+1]
keys are used to actually enter or change data.
The cursor keys also move you forward or backward
through the song: moving the cursor past the bottom of the
screen accesses subsequent measures, while moving it above
the top of the screen accesses the preceding measures (if there
are any). In the pattern display moving sideways takes you to the
time signature, style number, and section parameters.
In all of the STEP record displays the sequencer keys can
also be used to move forward or backward through the song.
[
U
] Go to first measure.
[
E
] Scroll up (see lower measure numbers)
[
R
] Scroll down (see higher measure numbers)
55
5
E a s y A c c o m p a n i m e n t
Style Number and Section
Any preset style number from 001 through 128, the “end
pattern” (number 129), or any user style number from U1
through U64 can be entered for each measure. The style name
appears to the right of the style number. Only one style & pattern
(section) can be entered per measure, and that pattern will begin
playing from the beginning of the measure at which it is entered.
A pattern entered once will continue to play until a differ-
ent pattern is entered. If you want to change sections without
changing the style number, only the section need be entered.
Playback will stop automatically when an “end pattern” (style
number 129) or an ending section is encountered.
In the example display below the intro pattern (section) of
style 006 plays for the first measure, then the main A pattern
(section) of the same style is selected in measure 2.
Style number/name
Section
56
E a s y A c c o m p a n i m e n t
Time Signature
Although the default time signature for the selected song
is automatically selected, the time signature value for each
measure can be changed as required. The available time signa-
tures are:
1/16 … 16/16
1/8 … 16/8
1/4 … 8/4
If a time signature is selected that results in shorter
measures than the pattern default, the pattern will be truncated
(cut short) accordingly. If the selected time signature results in
longer measures than the pattern default, the pattern will be
repeated to fill the specified measure length.
Erasing Pattern Changes
The function key immediately to the right of “ers” on the
display can be used to erase style number or section data at
which the cursor is located.
Press to erase style or
section at cursor
location.
57
5
E a s y A c c o m p a n i m e n t
“Cd” — Step Record Chord Changes
Here’s how the STEP record chord display will look if you’ve se-
lected an empty song (the appropriate chord data will appear if the se-
lected song contains data).
Chords
One chord can be entered per quarter note. Place the
cursor at the required quarter-note division on the display and
enter the chord by specifying the root and type via the micro-
keyboard (see page 40). In the example display below, an A major
chord is entered on the first beat of the first measure, a B minor
seventh on the third beat of the first measure, and a D major on
the first beat of the second measure.
Measure number
Time signature
1st measure
2nd measure
Subsequent measures follow
Place cursor at beat on
which chord is to be
entered
One beat
Chord
You can also enter a chord by playing the chord as it is on
the micro keyboard or an external keyboard if the Fingered Chord
function(FNGR) is previously set to “ON”.
58
E a s y A c c o m p a n i m e n t
Specifying the Bass Note For a Chord
You can specify the bass note to be used with any chord
by using the [OCT DOWN] key (note the “BASS” marking above
the key). Enter the chord by specifying the root and type, then
press the key on the micro-keyboard corresponding to the
desired bass note while holding the [OCT DOWN/BASS] key. The
bass note will appear to the right of a slash below the chord
name.
Example: Bm7 with E bass
59
5
E a s y A c c o m p a n i m e n t
NOTE
You can add bass notes to existing chords without having to re-enter
the entire chord by simply moving the cursor to the chord and using the
[OCT DOWN/BASS] key to specify the bass note. A bass note can be
removed from a chord by placing the cursor at the chord and re-
entering the chord.
If FNGR is set to “ON”, a bass note can be entered by
pressing a key for a bass note on the left part of the micro
keyboard or an external keyboard while holding the chord. (The
“left part” range for entering a bass note can be specified in the
Utility mode on page 227.)
Syncopated Chords
Chords can be syncopated (i.e. the chord actually begins an
eighth or sixteenth note before the beat on which it is entered)
by using the [OCT UP] key (note the “ ” marking above the
key). Enter the chord, then press the [OCT UP] key once for
eigth-note syncopation, or twice for sixteenth-note syncopation
(the appropriate syncopation symbol will appear below the chord
name).
Example: D chord syncopated (8th note)
60
E a s y A c c o m p a n i m e n t
NOTE
You can add syncopation to existing chords without having to re-enter
the entire chord by simply moving the cursor to the chord and pressing
the [OCT UP] key. Syncopation can be removed from a chord by placing
the cursor at the chord and pressing the [OCT UP] once or twice so that
the syncopation symbol disappears.
Erasing Chords
The function key immediately to the right of “ers” on the
display can be used to erase the chord at which the cursor is
located.
Press to erase chord
at cursor location.
Sound On/Off
You can hear the sound of entered chord in step recording.
If you don’t want to hear the sound, press the [MENU] key and
then the function key next to “Sound” to call the Sound on/off
display.
Press [-1/NO] key to turn the sound off, [+1/YES] key to
turn on.
61
6
T h e S o n g V o i c e M o d e
T h e S o n g V o i c e M o d e
The QY70 has 519 voices and 20 drum kits that can be se-
lected, played, and assigned to the 16 SONG mode sequencer tracks
via the SONG VOICE mode. The VOICE mode features a graphic on-
screen “mixer” that has mute/solo controls, pan pots, and faders for
each track. The SONG voice mode also provides access to effect
send controls and a versatile range of voice editing parameters (page
68).
Press the [SONG] key to select the voice mode mixer display.
The mixer display shows 8 of the 16 available tracks at a time. Use
the cursor keys to scroll left or right to the remaining tracks (an arrow
appears at either the left or right of the track numbers to indicate that
more tracks can be accessed by scrolling in the corresponding
direction).
Track numbers
Master fader
Mute/Solo parameters
Voice selectors
Pan pots
Volume faders
Pattern fader
62
T h e S o n g V o i c e M o d e
Mute/Solo
The Mute/Solo (“M/S”) parameters below each track
number in the VOICE mode mixer display can be used to mute
(turn off) or solo (only that track will be monitored) the corre-
sponding track. Move the cursor to the appropriate M/S param-
eter, then use the [-1] key to alternately mute or un-mute that
track, or use the [+1] key to alternately solo or un-solo the track.
Any number of tracks can be muted and/or soloed at a time. To
solo more than one track at a time hold the [SHIFT] key while
soloing additional tracks after the first solo track has been speci-
fied. Also hold the [SHIFT] key while un-soloing a single track
when multiple tracks are soloed (un-soloing a single track without
holding the [SHIFT] key will un-solo all soloed tracks).
The letter “M” appears below the number of tracks that
are muted, and the letter “S” appears when a track is soloed.
NOTE
The mute function is a handy way to simply turn tracks that you don’t
want to hear off. When recording, they also make it easy to mute a
“busy” track or several tracks that might make it difficult to hear an
important track.
Solo monitoring is a great way to isolate a track or two when you want
to concentrate on the sound while, for example, making delicate
adjustments to effects or other parameters that might get “swamped”
by the sound from other tracks. It’s also handy for listening for small
mistakes that you might otherwise overlook.
These same parameters also appear in the main SONG display. A track
that is muted or soloed in the main SONG display will also appear
muted or soloed in the voice mode mixer display, and vice-versa.
Mute (use the [-1] key)
Solo (use the [+1] key)
63
6
T h e S o n g V o i c e M o d e
The Voices
Due to the large number of voices provided in the QY70,
they are organized into 21 categories, as follows:
Prefix Category
Pf Piano
Cp Chromatic Percussion
Or Organ
Gt Guitar
Ba Bass
St Strings
En Ensemble
Br Brass
Rd Reed
Pi Pipe
Ld Lead Synth
Pd Pad
Fx Synth Effects
Et Ethnic instruments
Pc Percussive
Se Sound effects
Sfx More sound effects
Sfk Sound effect kits (i.e. a different effect on each key).
Dr Drum kits
Ds1 Drum set 1
(Drum kit including “editable” drum instruments)
Ds2 Drum set 2
(Drum kit including “editable” drum instruments)
See the List Book for a complete list of the voices with
their corresponding category, program number, and bank number.
To select a voice for a specific track, move the cursor to
the appropriate VOICE parameter and select using the [-1] and
[+1] keys or the SHIFT-Number entry method (page 34). You can
also skip to the first voice in each category by using the [-1/NO]
and [+1/YES] keys while holding the [SHIFT] key.
Note that the currently selected voice category, number,
and name appear at the top of the display. Also note that some of
the voices have variations, indicated by a plus sign (“+”) between
the program number and voice name. Play the micro keyboard
and you’ll hear that voice.
64
T h e S o n g V o i c e M o d e
NOTE
In any QY70 mode, the micro keyboard or an external MIDI keyboard
plays the voice assigned to the currently selected track. A MIDI
keyboard will also play the voice assigned to a track with the same
number as the external keyboard’s MIDI transmit channel unless the
“ECHO BACK” parameter (page 223) is set to “Rec Monitor”.
If you’re playing the micro keyboard, use the octave keys to access the
full range of instruments in each drum or effects kit.
See the List Book for a complete list of note assignments (i.e. which
drum instruments and SFX sounds are assigned to which notes) for all
drum and SFX kits.
The Pan Pots
Like the pan pots on a mixing console, the VOICE mode
pan pots can be used to position the sound of the corresponding
track anywhere from left to right in the stereo sound field.
Position the cursor at the pan pot, then use the [-1/NO] and [+1/
YES] keys to set the pan position. The graphic pan pot will rotate
to the corresponding position. The pan positions also have
numeric values (1 through 63) that appear at the top of the
display: “Center” is center, “Left 63” is full left, and “Right 63” is
full right. There’s also a “Random” setting in which the pan
position is set randomly.
The Volume Faders
Each track has a graphic volume “fader” that can be set to
produce the best “mix” (balance) between the various voices.
Position the cursor at a fader, then use the [-1/NO] and [+1/YES]
keys or the SHIFT-Number entry method to set the fader level.
The graphic fader will move to the corresponding position (higher
for higher volume, and lower for lower volume). The fader
positions also have numeric values (000 through 127) that appear
in the upper right corner of the display: “000” is minimum
volume (no sound) and “127” is maximum volume. The default
setting is “100” for all tracks. The leftmost “mst” fader is a
“master” fader which can be used to adjust the overall volume
level, while the “pat” fader independently controls the level of
the pattern track.
65
6
T h e S o n g V o i c e M o d e
NOTE
You can switch back and forth between the SONG and VOICE modes
even while a song is playing, so you can adjust all VOICE mode
parameters (change voices, mute tracks, pan, and change volume
settings) while listening to the results in real time!
66
T h e S o n g V o i c e M o d e
The Effect Send Display
The QY70 features a high-performance internal digital signal process-
ing system which provides a range of effects including reverb, delay,
modulation, distortion, and more. Three independent effect blocks are
provided — Reverb, Chorus, and Variation. The individual effects are
selected and modified via the EFFECT mode, described in detail on page
212. The VOICE mode mixer display provides acces to independent effect
send controls for each of the three effect blocks via the MENU sub-display:
press the [MENU] button, and then the function key next to “Effect Send”
on the display.
VOICE mode mixer display
67
6
T h e S o n g V o i c e M o d e
The VARI. (variation effect) control appears either as a standard
rotary control or a switch, depending on how the variation effect block is
“connected” to the system in the EFFECT mode (“System” or “Insertion”
— see page 215).
The effect controls — “REVERB”, “CHORUS”, and “VARI.” — set
the level of the corresponding effect for the corresponding parts. Position
the cursor at a control, then use [-1/NO] and [+1/YES] keys or the SHIFT-
Number entry method to set the corresponding effect level. The graphic
control will rotate to the corresponding position (clockwise for higher level,
and counter-clockwise for lower level). The control positions also have
numeric values (000 through 127) that appear at the top of the display:
“000” is no effect and “127” is maximum effect level. When the VARIA-
TION control appears as a switch, it simply turns the current variation
effect on or off (“E” appears in the switch when the variation effect is on).
The Mute/Solo and Voice selectors in the Effect Send display
duplicate those in the VOICE mode mixer display, and have exactly the
same functions.
You can return to the SONG VOICE mixer display by pressing the
[EXIT] key.
NOTE
The effect settings apply only to the QY70’s internal voices — i.e. they will not
affect the sound of an external tone generator or synthesizer being driven by the
QY70.
When the “VARI.” control appears as a standard rotary control (i.e., the variation
effect block is connected as a “System” effect), the “DRY” rotary control also
appears to control “Dry/Wet” mixing of effects for each track.
When the “VARI.” control appears as a switch (i.e., the variation effect block is
connected as an “Insertion” effect), the “DRY” rotary control disappears. In this
case, “Dry/Wet” mixing can be controlled in the “Vari.Edit” of the Effect Editing
display. (page 216)
Effect send display
VARI. = System effect VARI. = Insertion effect
68
T h e S o n g V o i c e M o d e
Voice Editing
The QY70 VOICE EDIT mode makes it possible to modify the sound
of the voices assigned to each track to best suit your particular musical
requirements. The VOICE EDIT mode can be accessed from the SONG
VOICE mode by pressing the [MENU] button, and then the function key
next to “Voice Edit” on the display. If a Drum Set is selected (“Ds1” or
“Ds2”) the “Drum Voice Edit” mode will also be available via the menu.
VOICE mode mixer display
69
6
T h e S o n g V o i c e M o d e
PB (Pitch Bend Range)
This control sets the maximum pitch bend control range.
The range is from “-24” through “0” to “+24”. Each
increment corresponds to one semitone (100 cents), thus
the maximum pitch bend control range is plus or minus
two octaves. The value set here also applies to the pitch
bend range controlled by the [OCT DOWN] key while
playing on the micro keyboard.
To edit a voice parameter, move the cursor to the parameter and edit
using either the [-1] and [+1] buttons or the SHIFT-Number entry method.
NOTE
The Mute/Solo and Voice selectors in the VOICE EDIT display duplicate those in the
VOICE mode mixer display, and have exactly the same functions.
You can return to the SONG VOICE mixer display by pressing the [EXIT] key.
VOICE EDIT display
PB
CUT RES A D R
70
T h e S o n g V o i c e M o d e
Filter Controls
The filter controls affect the basic “timbre” of the sound.
CUT (Cutoff Frequency)
Sets the cutoff frequency of the low-pass filter from “-64”
through “0” to “+63”. Negative values lower the cutoff
frequency, producing a “darker” sound. Positive values
raise the cutoff frequency, producing a brighter sound. The
graphic filter response curve will shift to indicate the
current setting (the heavy default setting curve will also
remain on the display).
RES (Resonance)
Adjusts the height of the filter’s resonance peak from “-
64” through “0” to “+63”. Negative values lower the
resonant peak producing a “flatter” sound. Positive values
increase the resonant peak, emphasizing components at
the filter cutoff frequency. The peak on the graphic filter
response curve will grow or shrink to indicate the current
setting (the heavy default setting curve will also remain on
the display).
Cutoff Frequency
Resonance
71
6
T h e S o n g V o i c e M o d e
EG (Envelope Generator) Controls
The envelope generator controls affect the level “enve-
lope” of the sound — i.e. its attack, decay, and release times.
Plotted against time, the level envelope looks something like this.
A (Attack Time)
Adjusts the attack portion of the envelope generator curve
from “-64” through “0” to “+63”. Negative values pro-
duce a faster attack while positive values produce a slower
attack. The graphic envelope generator curve will shift to
indicate the current setting (the heavy default setting curve
will also remain on the display).
D (Decay Time)
Adjusts the decay portion of the envelope generator curve
from “-64” through “0” to “+63”. Negative values pro-
duce a faster decay while positive values produce a slower
decay. The graphic envelope generator curve will shift to
indicate the current setting (the heavy default setting curve
will also remain on the display).
R (Release Time)
Adjusts the release portion of the envelope generator
curve from “-64” through “0” to “+63”. Negative values
produce a faster release while positive values produce a
slower release. The graphic envelope generator curve will
shift to indicate the current setting (the heavy default
setting curve will also remain on the display).
Attack
Decay
Release
72
T h e S o n g V o i c e M o d e
Drum Edit
When a Drum Set is selected (“Ds1” or “Ds2”) the “Drum Voice
Edit” mode can be selected via the SONG VOICE menu.
PITCH
CUT RES DECAY
REV
VAR
PAN
LV L
Selected drum kit
Current selected
drum instrument
Editable drum
instrument
“Ds1” or “Ds2”
73
6
T h e S o n g V o i c e M o d e
PICH (Pitch Coarse)
Adjusts the pitch of the selected drum instrument from “-
64” through “0” to “+63”. Negative values lower the pitch
of the instrument, while positive values raise the pitch of
the instrument.
REV (Reverb Send)
Independently adjusts the reverb send level of the selected
drum instrument from “0” (no reverb) to “127” (maximum
reverb).
VAR (Variation Send)
Independently adjusts the variation effect send level of the
selected drum instrument from “0” (no effect) to “127”
(maximum effect) when the variation effect block is
connected as a system effect, or turns the variation effect
“On (in case set to other than 0)” or “Off (in case set to
0)” when the variation effect block is connected as an
insertion effect (see page 215 for details on the effect
connections).
PAN (Pan Position)
Sets the pan position of the selected drum instrument.
“Center” is center, “Left 63” is full left, and “Right 63” is
full right. There’s also a “Random” setting in which the pan
position is set randomly.
LVL (Level)
Sets the level (volume) of the selected drum instrument
from “0” (no sound) to “127” (maximum volume).
Select the specific drum set to be edited by placing the cursor on
the drum set number and selecting via the [-1] and [+1] keys or by using
the SHIFT-Number entry method. Only certain drum instruments can be
edited, and these are indicated by dots on the appropriate keys in the
graphic keyboard display at the top of the display panel. Use the [OCT
DOWN] and [OCT UP] keys to access the full range of drum instruments,
and press the corresponding micro-keyboard key to select an instrument
for editing. When a drum instrument which cannot be edited is selected,
the controls on the display appear “grayed” and cannot be accessed.
74
T h e S o n g V o i c e M o d e
CUT (Cutoff Frequency)
Sets the cutoff frequency of the low-pass filter from “-64”
through “0” to “+63”. Negative values lower the cutoff
frequency, producing a “darker” sound. Positive values
raise the cutoff frequency, producing a brighter sound. The
graphic filter response curve will shift to indicate the
current setting (the heavy default setting curve will also
remain on the display).
RES (Resonance)
Adjusts the height of the filter’s resonance peak from “-
64” through “0” to “+63”. Negative values lower the
resonant peak producing a “flatter” sound. Positive values
increase the resonant peak, emphasizing components at
the filter cutoff frequency. The peak on the graphic filter
response curve will grow or shrink to indicate the current
setting (the heavy default setting curve will also remain on
the display).
DECAY (Decay Rate)
Adjusts the decay rate from “-64” through “0” to “+63”.
Negative values produce a slower decay while positive
values produce a faster decay (Unlike the Decay Time in
normal Voice Editing (page 71), this parameter sets the rate
for how much the level of the instrument decays. There-
fore, positive values produce a faster decay.). The graphic
envelope generator curve will shift to indicate the current
setting (the heavy default setting curve will also remain on
the display).
75
7
C r e a t i n g A C o m p l e t e S o n g
C r e a t i n g
A C o m p l e t e S o n g
In chapter 5, “Easy Accompaniment”, we learned how to
record the accompaniment tracks in the SONG mode. In this chapter
we’ll learn how to record the sequencer tracks to create complete
songs.
Preparing to Record — Voice Assignments
Recording the Sequencer Tracks
After recording the accompaniment tracks in the SONG mode using
either the preset patterns (chapter 5, page 44) or original patterns you have
created in the PATTERN mode (chapter 10, page 137), record melody lines,
harmony parts, counter-melodies, or any other parts required to complete
your composition on the SONG mode sequencer tracks. The SONG mode
provides realtime replace, realtime overdub, step, and multi recording
modes for the sequencer tracks.
Before actually beginning to record
you should switch to the SONG VOICE
mode and assign the desired voices to the
SONG mode sequencer tracks (page 61).
Of course, you can make these assign-
ments later but it’s better to record with
the voices you actually intend to use in
the song.
76
C r e a t i n g A C o m p l e t e S o n g
Realtime Sequencer Track Recording
In the realtime record mode you select the track you want to record
(1 through 16), and then play the part on the micro-keyboard or an external
MIDI keyboard in real time.
Z Select the SONG Mode & the Song To Be Recorded
Use the [SONG] key to select the main SONG mode
display and, with the cursor located over the song number at the
top of the display, use the [-1] and [+1] keys or the SHIFT-Number
entry method to select the song you intend to record.
X Select a Track to Record
Move the cursor to the track area of the display, and then
shift the cursor sideways to select the track you want to record:
1 through 16. The SONG display shows 8 of the 16 available
tracks at a time. Use the cursor keys to scroll left or right to the
remaining tracks (an arrow appears at either the left or right of
the track numbers to indicate that more tracks can be accessed
by scrolling in the corresponding direction). Move the cursor
vertically to move to other areas of the screen. The selected track
will remain highlighted.
Song number
77
7
C r e a t i n g A C o m p l e t e S o n g
C Engage the Record Ready Mode
Press the [
S
] key to engage the record ready mode. The
red LED above the [
S
] key will light.
Track
Record mode
selector
NOTE
Before engaging the record mode
you can also set the micro-keyboard
“velocity” via the “VELO” param-
eter. The velocity can be set in ten
levels — the more bars the higher
the velocity. There are also four
“random velocity” settings which
produce different degrees of random
velocity variation. “R1 produces the
smallest variation and “R4”
produces the greatest variation.
“VELO” parameter
78
C r e a t i n g A C o m p l e t e S o n g
If you want to add new material to a recorded track with-
out erasing the existing material as you record, select the
realtime overdub record mode (“OVER”) instead of the “REPL”
mode.
“REPL” button
B Set the Tempo and Time Signature Parameters As
Required.
Move the cursor to the tempo and time signature param-
eters and set as required using the [-1] and [+1] keys.
V Select the Realtime Replace or Overdub Record Mode
To select the realtime replace record mode — the mode
you’ll want to use when recording a new song — move the
cursor to the record mode selector area of the display (the area
with the “REPL”, “OVER”, “STEP”, and “MULTI” buttons), and
move it to the “REPL” (realtime replace) button, then press the
[+1/YES] key to select the realtime replace record mode (if it isn’t
already selected). An inverse “R” will appear in the selected
record mode button.
Tempo and
time signature
parameters
79
7
C r e a t i n g A C o m p l e t e S o n g
NOTE
It’s sometimes easier to set a slow tempo for realtime recording, so
you have plenty of time to enter the data.
N Record
Press the [
W
] key to begin recording. The metronome will
sound and you’ll be given a one-measure count-in prior to the first
measure actually recorded. Although the default count-in is one
measure, you can set the QY70 to provide anywhere from one to
eight count-in measures via the utility mode (page 220). The
current count-in measure number is indicated by a negative
number in the measure number section of the display.
Play the required part either on the micro-keyboard or via
an external MIDI keyboard.
M Stop Recording
Press the [
A
] key to stop recording. The normal SONG play
mode is automatically re-selected when you stop recording.
Note that when you return to the SONG play mode a bar
will appear below each track that contains data. This is the lowest
segment of a “velocity meter” which will indicate velocity levels
in the track during playback.
Count-in
80
C r e a t i n g A C o m p l e t e S o n g
< Record the Remaining Tracks
Complete the song by re-engaging the record mode,
selecting the next track to be recorded, and recording as de-
scribed above.
NOTE
See the “Editing Songs & Patterns” section , page 192, for information
on how to edit recorded song data.
Recorded
track
About the “MULTI” Recording
If you select the “MULTI” mode in step V on page 78, the
QY70 will simultaneously record data received over MIDI channels 1
to 16 onto the corresponding sequencer tracks (1 to 16). This is useful
when you want to record a multipart recording from a computer or
another sequencer in real time, or when you want to record from a
MIDI insrtrument (such as a MIDI guitar) that outputs over multiple
channels.
Before starting the multipart recording, be sure to set the MIDI
Sync to “External” (page 222), MIDI Control to “In” or “In/Out” (page
222), Rec Count to “OFF” (page 221). Then engage the record ready
mode (page 77) and select “MULTI” record mode. When you start
the external computer or sequencer, the QY70 will start multipart
recording automatically.
81
7
C r e a t i n g A C o m p l e t e S o n g
Z Select the SONG Mode & the Song To Be Recorded
Use the [SONG] key to select the main SONG mode
display and, with the cursor located over the song number at the
top of the display, use the [-1] and [+1] keys or the SHIFT-Number
entry method to select the song you intend to record.
Step Sequencer Track Recording
The step record mode lets you enter each track note-by-note, with
precise control over the timing, length, and loudness of each note. You can
record entire tracks using the step mode, or use it to brush-up and add
data to an existing track.
Song number
X Select a Track to Record
Move the cursor to the track area of the display, and then
shift the cursor sideways to select the track you want to record:
1 through 16. The SONG display shows 8 of the 16 available
tracks at a time. Use the cursor keys to scroll left or right to the
remaining tracks (an arrow appears at either the left or right of
the track numbers to indicate that more tracks can be accessed
by scrolling in the corresponding direction). Move the cursor
vertically to move to other areas of the screen. The selected track
will remain highlighted.
82
C r e a t i n g A C o m p l e t e S o n g
V Select the Step Record Mode
Move the cursor to the record mode selector area of the
display (the area with the “REPL”, “OVER”, “STEP”, and
“MULTI” buttons), and move it to the “STEP” button, then press
the [+1/YES] key to select the step record mode (if it isn’t already
selected). An inverse “R” will appear in the selected record
mode button.
C Engage the Record Ready Mode
Press the [
S
] key to engage the record ready mode. The
red LED above the [
S
] key will light.
Track
Record mode
selector
83
7
C r e a t i n g A C o m p l e t e S o n g
B Engage the Record Mode
Press the [
W
] key to engage the step record mode. The
step record display shown below will appear.
Current record track.
Time signature.
Note parameters.
Note display.
Measure/beat/clock display.
“STEP” button
N Set the Note Parameters as Required
Move the cursor to the note, velocity, and gate time
parameters and set as required using the [-1] and [+1] keys for
the first (or next) note to be entered.
84
C r e a t i n g A C o m p l e t e S o n g
STEP (Note length)
32nd, 16th, 16th triplet, 8th, 8th
triplet, quarter, quarter triplet, half, whole.
VELO (Velocity)
More bars = higher velocity, adjustable in 10
steps (ppp, pp, p, mp, normal, mf, f, ff, fff, ffff).
~ produces random velocity.
GATE (Gate time)
= staccato (50%).
= normal (90%).
= slur (99%).
M Enter a Note
Once the note parameter have been specified, the note
can be entered simply by playing the appropriate key on the
micro-keyboard (or on your external MIDI keyboard). A dot
appears on the note display and the note pointer advances to the
next note position. Chords are also indicated by a dot. Here’s how
the display will look after two 8th notes have been entered.
NOTE
If you use an external MIDI keyboard for step recording, the QY70
always accepts velocity from the external keyboard regardless of the
“VELO” setting.
85
7
C r e a t i n g A C o m p l e t e S o n g
The Note Display
The note display shows up to four 1/4-notes worth of data
at once (that’s one measure in 4/4 time). If the selected
time signature results in more than four 1/4 notes per
measure, then the display will scroll to show the extra
notes.
Moving Around In the Note Display
You can move the cursor down to the note display (the
note pointer will appear filled) and move the note pointer to
any position at which you want to enter a note, or to any
note that you want to delete. You will actually hear the
appropriate note or chord when the note pointer is moved
to an existing note. When you move the note pointer past
the end of the note display, the next measure will appear.
Cursor moved to note pointer (pointer filled).
Note that the pointer points up to notes in the
upper row and down to notes in the lower row.
1st beat. 2nd beat.
Each dash represents a
32nd note (60 clocks).
3rd beat.
Note
pointer
4th beat.
86
C r e a t i n g A C o m p l e t e S o n g
The Step Mode Function Keys
The four function keys immediately to the right of the
display provide acces to a number of handy functions in
the step record mode. The “del” (delete) key deletes the
note or chord at the note pointer. The “Bdl” (back delete)
key moves the note pointer backward by the currently
selected note length and deletes the note at that position.
The “rst” (rest) key enters a rest of the currently selected
note length at the note pointer position. And the “tie” key
lengthens the previously entered note by “tying” another
note of the same length (specified by the STEP parameter)
and pitch to it. The “tie” key only works immediately after
entering a note.
The Measure/Beat/Clock Display
The “Meas” area of the step record display shows the
current position of the note pointer in measures, beats,
and clocks (there are 480 clocks per 1/4 note). If you’re not
sure what measure you’re seeing on the note display while
recording, check the measure/beat/clock display.
You can move the note pointer to any measure by moving
the cursor to the measure number and entering the value
with the [-1] and [+1] keys or the SHIFT-Number entry
method.
87
7
C r e a t i n g A C o m p l e t e S o n g
< Complete the Song
Repeat steps N and M until the current track is complete,
then press [
A
] to stop recording and select the next track for
recording, as necessary.
Beat
(01, 02, 03, 04 if 4/4 time).
Measure number
(001 ... 999)
Clock
(480 clocks per 1/4 note).
NOTE
See the “Editing Songs & Patterns” section , page 192, for information
on how to edit recorded song data.
88
P l a y b a c k C o n t r o l
P l a y b a c k C o n t r o l
The normal SONG mode display includes all the parameters
and controls you need for song playback. Press the [SONG] key to go
to the SONG play mode (depending on the current mode, you may
need to press the [SONG] key more than once).
Song number
Song name
Measure number
Tempo
Time signature
Micro-keyboard
octave indicator
Jump mode (Off/
Stop/Top) and
location
Accompaniment
tracks (Pattern,
Chord, Tempo)
Sequencer tracks
(1 … 16)
Style number &
name
Style section name
Chord display
Chord template number
Velocity meters &
Mute/Solo buttons
Micro-keyboard velocity
Transpose
Fingered Chord on/off
89
8
P l a y b a c k C o n t r o l
Selecting a Song
The QY70 can retain up to 20 different songs in memory at
the same time: song numbers 01 through 20 (three demo songs
are recorded as song numbers 21 through 23). To select a song
for playback use the cursor keys to move the cursor to the song
number location (the song number will be highlighted), and then
use the [-1] and [+1] keys or the SHIFT-Number entry method
desribed below to select the desired song number. If the song
has been given a name (this is done via the Song Name job
described on page 136), the song name will appear to the right of
the song number.
The SHIFT-Number Entry Method
Numeric values can be directly entered by using the black
micro-keyboard keys (numbered 1 through 0) while holding
the [SHIFT] key. To enter the number “16”, for example,
press the “1” and then the “6” keys (“F#/Gb” and “7
(#9)
/
7
(b9)
” on the micro-keyboard) while holding the [SHIFT]
key. The entered number — “16” — will flash on the
display. Press the [ENTER] key to actually enter the num-
ber.
Negative values can be entered where applicable by first
pressing the “E” (“-”) key on the micro-keyboard while
holding the [SHIFT] key, and then entering the value as
described above.
Playing the Selected Song
Playback of the selected song is started by pressing the [
W
]
(“PLAY”) sequencer key. The green LED will flash at the playback
tempo. The song will play through to the end and then stop
automatically. Song playback can also be stopped at any time by
pressing the [
A
] sequencer key.
NOTE
When a song is selected, its voice and effect settings will be recalled.
Therefore, you should wait for about 1 second until pressing the [
W
]
button after selecting a song.
90
P l a y b a c k C o n t r o l
Repeat Playback
Press the [
W
] key while holding the [SHIFT] key to start
repeat playback of the selected song. The repeat playback
symbol ( ) will appear in the upper right corner of the display
during repeat playback. In this mode the selected song will
repeat indefinitely untill stopped by pressing the [
A
] key.
Measure Number
The measure number parameter on the display shows the
current measure number during song playback (and recording).
You can also place the cursor here and use the [-1] and [+1] keys
or the SHIFT-Number entry method to enter any measure number
from which you want to start playback or recording. The se-
quencer [
E
] and [
R
] keys can be used to step or scroll forward
or backward through the song’s measures no matter where the
cursor is located.
Jump Functions
For convenient navigation the QY70 has two “jump”
modes that let you jump to a specified measure number.
Jump Mode Symbol Function
Stop Jump When this mode is selected the QY70
will automatically jump to the
specified measure number whenever
the sequencer [
A
] (Stop) key is
pressed.
Top Jump In this mode the QY70 will automati-
cally jump to the specified measure
number when the sequencer [
U
] (Top)
key is pressed and the current
measure number is greater than the
specified jump location. If the current
measure number is lower than the
specified jump location the QY70 will
jump to the top of the song (measure
001).
Jump Off [-
-] The jump function is OFF.
91
8
P l a y b a c k C o n t r o l
The jump modes can be selected by moving the cursor to
the jump mode symbol and selecting via the [-1] and [+1] keys, or
by using the following key combinations:
Mode Key Combination
Stop Jump [SHIFT] + [
A
]
Top Jump [SHIFT] + [
U
]
Jump Off [SHIFT] + [
E
] or [
R
]
To specify the measure number you want to jump to move
the cursor to the jump location parameter and use the [-1] and
[+1] keys or the SHIFT-Number entry method to set as required.
Playback Tempo
The playback tempo can set from 25 to 300 quarter-note
beats per minute by moving the cursor to the tempo parameter
and using the [-1] and [+1] keys or the SHIFT-Number entry
method to set as required.
Track Selection
Although track selection is more of a recording than a
playback function, it is necessary to select tracks in the playback
mode for muting and solo monitoring control (below). The SONG
display shows the pattern (“Pt”), chord (“Cd”), and tempo
(“Tm”) accompaniment tracks as well as 8 of the 16 available
sequencer tracks at a time. Move the cursor to the track area and
scroll left or right to the remaining tracks (an arrow appears at
either the left or right of the track numbers to indicate that more
tracks can be accessed by scrolling in the corresponding direc-
tion). The number of the selected track remains highlighted when
the cursor is moved to other areas of the display.
92
P l a y b a c k C o n t r o l
The Velocity Meters
The area below each sequencer track number is a 5-
segment “velocity” meter that shows approximate MIDI velocity
in the corresponding track during playback. When playback is
stopped, the lowest segment of the velocity meter appears only
below tracks which contain data.
Mute/Solo
The velocity meter area below each track number in the
SONG mode also functions as a mute/solo button which can be
used to mute (turn off) or solo (only that track will be monitored)
the corresponding track. Move the cursor to the track, then use
the [-1] key to alternately mute or un-mute that track, or use the
[+1] key to alternately solo or un-solo the track. Any number of
tracks can be muted and/or soloed at a time. To solo more than
one track at a time hold the [SHIFT] key while soloing additional
tracks after the first solo track has been specified. Also hold the
[SHIFT] key while un-soloing a single track when multiple tracks
are soloed (un-soloing a single track without holding the [SHIFT]
key will un-solo all soloed tracks).
The letter “M” appears below the number of tracks that
are muted, and the letter “S” appears when a track is soloed.
NOTE
The mute function is a handy way to simply turn tracks that you don’t
want to hear off. When recording, they also make it easy to mute a
“busy” track or several tracks that might make it difficult to hear an
important track.
Solo monitoring is a great way to isolate a track or two when you want
to concentrate on the sound while, for example, making delicate
adjustments to effects or other parameters that might get “swamped”
by the sound from other tracks. It’s also handy for listening for small
mistakes that you might otherwise overlook.
93
8
P l a y b a c k C o n t r o l
Velocity
This parameter sets the “velocity” (i.e. loudness) of the
micro-keyboard. The velocity can be set in ten levels — the more
bars the higher the velocity. There are also four “random veloc-
ity” settings which produce different degrees of random velocity
variation. “R1 produces the smallest variation and “R4” produces
the greatest variation.
Transposition
The transpose (“TRNS”) parameter can be used to trans-
pose the pitch of song playback up or down by a maximum of 2
octaves in semitone increments. A transpose setting of “+00”
produces normal pitch. To transpose song playback move the
cursor to the “TRNS” parameter and use the [-1] and [+1] keys or
the SHIFT-Number entry method to set as required. Minus
settings transpose down, and plus settings transpose up by the
specified amount. Each increment corresponds to one semitone.
The maximum range is from “-24” through “+00” to “+24”.
Fingered Chord
This parameter can either be turned “OFF” or “ON”.
When “ON” chords played in the specified “fingered zone” of
the micro-keyboard or an external MIDI keyboard are recognized
by the QY70 and the chord accompaniment track is reharmonized
accordingly. See page 227 for details.
94
P l a y b a c k C o n t r o l
Play Effects
The QY70 “Play Effects” affect sequence playback in real time, and
are not actually recorded with the sequence data. The Play Effects include
Groove Quantization and Drum Table Remapping.
To access the Play Effects press the [MENU] key while in the SONG
mode and press the function key next to “Play Fx” on the display. The
“Groove” and “Drum Table” displays can then be selected by pressing the
[MENU] key and then the function key next to “Groove” or “Drum Table”
on the display, as required.
NOTE
The Play Effects settings can be stored for each song.
See the “Normalize” job on page 133 to apply the Play Effects to the actual
sequence data.
95
8
P l a y b a c k C o n t r o l
Groove Quantization display
Drum Table display
96
P l a y b a c k C o n t r o l
Groove Quantization
If the Groove display shown below does not appear when “Play Fx”
is selected, press the [MENU] key again and press the function key next to
“Groove” on the display.
“Groove Quantization” is different from standard quantization in that
specific beats within a track are shifted away from precise on-the-beat
timing to create a natural “groove”. Both the timing and velocity of certain
notes can be affected by groove quantization.
The Groove display shows 8 of the 16 available tracks at a time. Use
the cursor keys to scroll left or right to the remaining tracks (an arrow
appears at either the left or right of the track numbers to indicate that more
tracks can be accessed by scrolling in the corresponding direction).
Mute/Solo buttons
FX THRU switches
Groove template
Timing
Velocity
Sequencer tracks
(1 … 16)
97
8
P l a y b a c k C o n t r o l
M/S (Mute/Solo)
The Mute/Solo (“M/S”) parameters below each track
number in the Groove display can be used to mute (turn off) or
solo (only that track will be monitored) the corresponding track.
Move the cursor to the appropriate M/S parameter, then use the
[-1] key to alternately mute or un-mute that track, or use the [+1]
key to alternately solo or un-solo the track. Any number of tracks
can be muted and/or soloed at a time. To solo more than one
track at a time hold the [SHIFT] key while soloing additional tracks
after the first solo track has been specified. Also hold the [SHIFT]
key while un-soloing a single track when multiple tracks are
soloed (un-soloing a single track without holding the [SHIFT] key
will un-solo all soloed tracks).
The letter “M” appears below the number of tracks that
are muted, and the letter “S” appears when a track is soloed.
NOTE
The M/S parameters duplicate those in the SONG play mode and
SONG VOICE displays, and have exactly the same effect.
FX THRU
These “switches” enable or bypass the effect for the
corresponding tracks. When an FX THRU switch appears as an
empty square, the effect is enabled for that track. To bypass the
effect for a track, move the cursor to the appropriate FX THRU
switch, and press the [+1] key so that a “T” (THRU) in the
square. Bypassed tracks can be enabled by pressing the [-1] key.
GROOVE TEMPLT
This parameter selects one of the 100 available groove
templates for the corresponding track. Each groove template
affects different beats in different ways, thus creating different
grooves. See the List Book for a complete list of the available
groove templates. To select a groove template for a track, , move
the cursor to the appropriate GROOVE TEMPLT parameter, then
use the [-1] and [+1] parameters or the SHIFT-Number entry
98
P l a y b a c k C o n t r o l
method to select the desired template. No groove template is
selected when “-
-” appears in the GROOVE TEMPLT parameter
location.
TIMING
The TIMING controls determine to what degree the timing
of the notes in the corresponding track is affected by the se-
lected groove template. The range is from “000” to “200”.
Higher values produce greater timing variation (“100” is the
default setting).
VELOC
The VELOC controls determine to what degree the velocity
of the notes in the corresponding track is affected by the se-
lected groove template. The range is from “000” to “200”.
Higher values produce greater velocity variation (“100” is the
default setting).
Drum Table Remapping
If the Drum Table display shown below does not appear when “Play
Fx” is selected, press the [MENU] key again and press the function key
next to “Drum Table” on the display.
Drum Table remapping allows the drum instruments to be
“remapped” so that, for example, you can replace a medium snare drum
with a high snare or rimshot without affecting the data in the drum track.
Mute/Solo buttons
FX THRU switches
Drum table
Sequencer tracks
(1 … 16)
99
8
P l a y b a c k C o n t r o l
M/S (Mute/Solo)
The Mute/Solo (“M/S”) parameters below each track
number in the Drum Table display can be used to mute (turn off)
or solo (only that track will be monitored) the corresponding track.
Move the cursor to the appropriate M/S parameter, then use the
[-1] key to alternately mute or un-mute that track, or use the [+1]
key to alternately solo or un-solo the track. Any number of tracks
can be muted and/or soloed at a time. To solo more than one
track at a time hold the [SHIFT] key while soloing additional tracks
after the first solo track has been specified. Also hold the [SHIFT]
key while un-soloing a single track when multiple tracks are
soloed (un-soloing a single track without holding the [SHIFT] key
will un-solo all soloed tracks).
The letter “M” appears below the number of tracks that
are muted, and the letter “S” appears when a track is soloed.
NOTE
The M/S parameters duplicate those in the SONG play mode and
SONG VOICE displays, and have exactly the same effect.
FX THRU
These “switches” enable or bypass the effect for the
corresponding tracks. When an FX THRU switch appears as an
empty square, the effect is enabled for that track. To bypass the
effect for a track, move the cursor to the appropriate FX THRU
switch, and press the [+1] key so that a “T” (THRU) in the
square. Bypassed tracks can be enabled by pressing the [-1] key.
100
P l a y b a c k C o n t r o l
DRUM TABLE
This parameter specifies the drum instrument to be
remapped for the selected track. 24 choices are available (in
addition to “-
-” or “OFF”), spanning 6 remapping categories, as
shown in the chart below. A selected instrument will replace any
other instrument in the same category. For example, if a drum
track uses the Snare M instrument and you select DRUM TABLE
number 7 for that track, every occurence of the Snare M instru-
ment will be replaced by the Open Rimshot instrument.
No. Category Instrument
1 Bass Drum L
2 Bass Drum Bass Drum M
3 Bass Drum H
4 Snare L
5 Snare M
6 Snare H
7
Snare
Open Rimshot
8 Brush Slap
9 Side Stick
10 Hand Clap
11 Mid Tom
12 Ride Cymbal
13 Cabasa
14
Hi Hat
Maracas
15 Triangle
16 Shaker
17 Tambourine
18 Bongo-Conga Bongo-Conga
19 Solo BassDr
20 Solo Solo SnareDr
21 Solo Hi-Hat
22 Mute BassDr
23 Mute Mute SnareDr
24 Mute Hi-Hat
101
9
T h e S o n g J o b s
T h e S o n g J o b s
The SONG mode includes 25 song “jobs” that perform a
variety of important functions. To access and use the song jobs, press
the [MENU] key while in the main SONG play mode, then press the
“Job” function key. This calls the song job list. You can select any job
on the list simply by moving the cursor to the required job and press-
ing [ENTER]. The function keys can be used to move the cursor
directly to the first job in the corresponding category: Event, Measure,
Track, or Song (press the [MENU] key, then the appropriate function
key).
102
T h e S o n g J o b s
Returning to the SONG Mode
The [EXIT] key can be used to exit from any song job, and then from the job list thereby
returning you to the normal song play mode. You can also press the [SONG] key to
directly return to the SONG mode.
00: Undo/Redo
“Event” category
01: Quantize
02: Modify Velocity
03: Modify Gate Time
04: Crescendo
05: Transpose
06: Shift Clock
07: Chord Sort
08: Chord Separate
09: Copy Event
10: Erase Event
11: Extract Event
12: Create Continuous
13: Thin Out
14: Time Stretch
“Measure” category
15: Create Measure
16: Delete Measure
“Track” category
17: Copy Track
18: Mix Track
19: Clear Track
20: Expand Backing
21: Normalize
“Song” category
22: Copy Song
23: Clear Song
24: Song Name
103
9
T h e S o n g J o b s
00 : Undo/Redo
This job will “undo” any other song/pattern job, edit, or record
function if it is executed before any other operation is performed. In all
cases the affected data is restored to the state it was in before performing
the job, edit, or record operation. This job will also undo the last undo
operation (redo).
The name of the last operation performed will appear on the display
(i.e. the operation which will be “undone”). In the example display, above,
a quantize operation will be undone.
Press [ENTER] to execute the Undo/Redo job. The metronome icon
will appear on the display while the data is being processed, then “Com-
pleted” will appear briefly when the job is done. Press the [EXIT] key to
return to the job list, or a mode key to go directly to the selected mode.
DETAIL
The UNDO/REDO job will not undo the Clear Song (“All”), the Clear Pattern (“All”
styles), the Song Name or Style Name jobs.
Name of the last
operation performed
104
T h e S o n g J o b s
01 : Quantize
Aligns notes in the specified track to or close to the nearest speci-
fied beat.
Quantize Values
Value Effect
Aligns to the nearest 32nd note.
Aligns to the nearest 16th note triplet.
Aligns to the nearest 16th note.
Aligns to the nearest 8th note triplet.
Aligns to the nearest 8th note.
Aligns to the nearest quarter note triplet.
Aligns to the nearest quarter note.
The “TR” parameter selects the track to be affected by the Quantize
job: “01” … “16” for individual tracks, or “All” to quantize all 16 tracks
simultaneously.
The “M” parameters above the graphic bar are used to specify the
first measure:beat and last measure:beat of the range to be quantized.
The “Quantize” parameter determines to what beats the note data
in the specified track will be aligned. If you select “ ”, for example, all
notes in the track will be aligned to the nearest 16th-note beat, to a degree
determined by the “Strength” parameter.
First beat.
First measure. Last measure.
Last beat.
105
9
T h e S o n g J o b s
The “Strength” parameter determines how “strongly” the notes
are attracted to the specified quantize value. The strength range is from
0% to 100%. At a setting of “0%” no quantization will occur, while a
setting of “100%” will cause all notes to be aligned precisely to the
nearest specified beat value. In-between settings produce a corresponding
shift in the position of all off-beat notes to the nearest specified beat value.
With a value setting of “ ” and a strength setting of 50%, for example, a
note that does not fall precisely on a quarter beat will be shifted about
halfway to nearest quarter beat.
Aligns to the nearest 16th note + 16th note triplet.
Aligns to the nearest 8th note + 8th note triplet.
The “Swing Rate” parameter produces a “swing” feel by shifting
the timing of “back beats”, as specified by the quantize value. For ex-
ample, if the specified quantization value is 8th notes, then the swing
effect will shift the 2nd, 4th, 6th, and 8th beats of each measure forward
to create a swing feel. If the quantize value is set to a triplet note length,
the last note in each triplet group will be shifted. If the quantize value is set
to a compound note length (e.g. 8th note + 8th note triplet) the even-
numbered back beats will be shifted. The “Swing Rate” parameter deter-
mines how much the timing of the affected notes will be shifted. The
range is from 50% (no swing) to 75% (maximum swing) for even note
lengths, from 66% to 83% for triplet note lengths, and from 50% to 66%
for even-plus-triplet note lengths (e.g. 8th note + 8th note triplet).
Original data (assuming 4/4 meter)
Quantizing strength = 100% (quantize value = )
Quantizing strength = 50% (quantize value = )
106
T h e S o n g J o b s
The “Gate Time” parameter increases or decreases the gate times
(length) of all notes affected by the swing parameter. The range is from 0%
to 200%. The “Gate Time” parameter sets the ratio between the shorter
and longer gate time values. A setting of “100%” maintains the original
relationship between the notes, lower values produce a narrower gate time
range, and higher values produce a broader gate time range.
After setting the parameters as required press [ENTER] to execute
the Quantize job. The metronome icon will appear on the display while the
data is being processed, then “Completed” will appear briefly when the
job is done. Press the [EXIT] key to return to the job list, or a mode key to
go directly to the selected mode.
Original timing
Quantizing value = , Swing rate 50% (no delay)
Quantizing value = , Swing rate 60% (delay applied)
Quarter-note length
107
9
T h e S o n g J o b s
02 : Modify Velocity
Increases or decreases the velocity values of all notes in the speci-
fied track and range of measures.
The “TR” parameter selects the track to be affected by the Modify
Velocity job: “01” … “16”.
The “M” parameters above the graphic bar are used to specify the
first measure:beat and last measure:beat of the range to be modified.
The “SetAll” parameter makes it possible to set all notes in the
specified range to a single velocity value from “1” to “127”. “Set All” can
also be turned “Off” when the “Rate” and “Offset” parameters, below,
are to be used for velocity modification.
The “Rate” parameter allows you to change the Velocity value of
each note without affecting the velocity ratios between notes (proportional
change). A setting of
“100%” maintains the
absolute velocity differ-
ences between notes,
while lower (higher) values
will decrease (increase)
the velocity values to the
corresponding percentage,
resulting in a narrower
(wider) dynamic range.
The range is from “0%” to
“200%”.
First beat.
First measure. Last measure.
Last beat.
96 64 32 127 96
48 32 16 63 48
127 96 48 127 127
Original
velocities
Rate = 50%
Rate = 150%
108
T h e S o n g J o b s
New Velocity = Original Velocity x rate/100 + offset
(If the right side of the equation is 0 or less, the New Velocity
becomes 1. If the right side of the equation is 128 or more, the New
Velocity becomes 127.)
After setting the parameters as required press [ENTER] to execute
the Modify Velocity job. The metronome icon will appear on the display
while the data is being processed, then “Completed” will appear briefly
when the job is done. Press the [EXIT] key to return to the job list, or a
mode key to go directly to the selected mode.
NOTE
The Modify Velocity job is a great way to “soften” the sound of material that has
too great variation between the softest and loudest notes, or, conversely, to add
extra punch to dull-sounding material. Experiment with the parameters to get a feel
for what they do.
The “Offset” parameter allows you to change all velocity values by
an absolute amount. “-” settings will decrease the velocity of each note by
the corresponding amount, “+” settings will increase the velocity accord-
ingly. The range is from “-99” through “0” to “+99”.
96 64 32 127 96
76 44 12 107 76
116 84 52 127 116
Original
velocities
Offset = -20
Offset = +20
109
9
T h e S o n g J o b s
03 : Modify Gate Time
Increases or decreases the gate times (length) of all notes in the
specified track and range of measures.
The “TR” parameter selects the track to be affected by the Modify
Gate Time job: “01” … “16”.
The “M” parameters above the graphic bar are used to specify the
first measure:beat and last measure:beat of the range to be modified.
The “SetAll” parameter makes it possible to set all notes in the
specified range to a single gate time value from “1” to “9999”. “Set All”
can also be turned “Off” when the “Rate” and “Offset” parameters,
below, are to be used for gate time modification.
The “Rate” parameter allows you to change the Gate Time value of
each note without affecting the gate time ratios between notes (propor-
tional change). A setting of “100%” maintains the absolute gate time
differences between notes, while lower (higher) values will decrease
(increase) the gate time values to the corresponding percentage. The range
is from “0%” to “200%”.
First beat.
First measure. Last measure.
Last beat.
32 32 32 48 48
16 16 16 24 24
48 48 48 72 72
Original
gate time
Rate = 50%
Rate = 150%
110
T h e S o n g J o b s
New Gate Time = Original Gate Time x rate/100 + offset
(If the right side of the equation is 0 or less, the New Gate Time
becomes 1)
After setting the parameters as required press [ENTER] to execute
the Modify Gate Time job. The metronome icon will appear on the display
while the data is being processed, then “Completed” will appear briefly
when the job is done. Press the [EXIT] key to return to the job list, or a
mode key to go directly to the selected mode.
NOTE
The Modify Gate Time job can be used to produce a more staccato or legato feel,
as required. Experiment with the parameters to get a feel for what they do.
32 32 32 48 48
12 12 12 28 28
52 52 52 68 68
Original
gate time
Offset = -20
Offset = +20
The “Offset” parameter allows you to change all gate time values by
an absolute amount. “-” settings will decrease the gate time of each note
by the corresponding amount, “+” settings will increase the gate time
accordingly. The range is from “-9999” through “0” to “+9999”.
111
9
T h e S o n g J o b s
04 : Crescendo
Produces a gradual crescendo (increase in note velocity) or decre-
scendo (decrease in note velocity) in the specified track over the specified
range of measures.
The “TR” parameter selects the track to be affected by the Cre-
scendo job: “01” … “16”.
The “M” parameters above the graphic bar are used to specify the
first measure:beat and last measure:beat of the range to be modified.
The “Range” parameter determines the range of velocity values
over which the crescendo will occur. A setting of “+24”, for example, will
cause the MIDI velocity values to increase by 24 over the specified mea-
sure range (The MIDI velocity value range is from 1 to 127).
First beat.
First measure. Last measure.
Last beat.
Negative values cause a corresponding decrease in velocity, thereby
producing a decrescendo rather than a crescendo. The range of this
parameter is from “-99” through “0” to “+99”.
Specified measure (“M”) range.
Range +24.
Crescendo.
Original
velocity.
112
T h e S o n g J o b s
After setting the parameters as required press [ENTER] to execute
the Crescendo job. The metronome icon will appear on the display while
the data is being processed, then “Completed” will appear briefly when
the job is done. Press the [EXIT] key to return to the job list, or a mode key
to go directly to the selected mode.
113
9
T h e S o n g J o b s
05 : Transpose
Transposes all notes in the specified part up or down by the speci-
fied number of semitones.
The “TR” parameter selects the track to be affected by the Trans-
pose job: “01” … “16” for the sequncer tracks, or “Cd” for the accompa-
niment chord track.
The “M” parameters above the graphic bar are used to specify the
first measure:beat and last measure:beat of the range to be modified.
The “Note” parameters specify the range of notes to be affected.
The maximum range is from “C-2” to “G8”.
The “Transpose” parameter determines the amount of transposi-
tion in semitone increments. Minus (-) values transpose down while plus
(+) values transpose up. the range is from “-99” through “0” to “+99”.
After setting the parameters as required press [ENTER] to execute
the Transpose job. The metronome icon will appear on the display while
the data is being processed, then “Completed” will appear briefly when
the job is done. Press the [EXIT] key to return to the job list, or a mode key
to go directly to the selected mode.
NOTE
Of course, you can transpose all tracks as required to shift the entire song to a
different key, but the Transpose job is actually more suited to changing the pitch of
a section of a single track. This can be done to produce temporary “modulations”
to another key, or to create harmony with another track.
First beat.
First measure. Last measure.
Last beat.
114
T h e S o n g J o b s
06 : Shift Clock
Moves all notes and events in the specified track and range of
measures forward or backward by the specified number of clocks (480
clocks per 1/4 note).
First beat.
First measure. Last measure.
Last beat.
The “TR” parameter selects the track to be affected by the Shift
Clock job: “01” … “16” for the sequencer tracks, or “Tm” for the tempo
track.
The “M” parameters above the graphic bar are used to specify the
first measure:beat and last measure:beat of the range to be modified.
The “Clock” parameter determines the direction and number of
clocks by which the notes in the specified measure range will be shifted.
“+” settings shift the notes forward (toward the end of the song) and “-”
settings shift the notes backward (toward the beginning of the song). The
range is from “-9999” through “0000” to “+9999”.
After setting the parameters as required press [ENTER] to execute
the Shift Clock job. The metronome icon will appear on the display while
the data is being processed, then “Completed” will appear briefly when
the job is done. Press the [EXIT] key to return to the job list, or a mode key
to go directly to the selected mode.
115
9
T h e S o n g J o b s
NOTE
The Shift Clock job will not shift data beyond the specified measure range. Events
near the beginning and end of the specified range may therefore sound “bunched”
together in some cases.
Since the Shift Clock job actually shifts the timing of all notes and other events in
the specified measures forward or backward, it can significantly alter the “feel” of
the song. You could move the notes forward (“+” settings) to create a more “laid
back” feel, or backward (“-” settings) to produce a more “driving” feel. Of course,
you can also use Shift Clock to correct timing that is off in the first place.
116
T h e S o n g J o b s
07 : Chord Sort
Sorts all notes in the specified measure range which fall on the
same beat (i.e. chords) so that the notes are arranged in order from lowest
to highest or from highest to lowest.
First beat.
First measure. Last measure.
Last beat.
The “TR” parameter selects the track to be affected by the Chord
Sort job: “01” … “16”.
The “M” parameters above the graphic bar are used to specify the
first measure:beat and last measure:beat of the range to be modified.
The “Type” parameter determines whether the chords in the
specified range are arranged from lowest to highest note (“Normal”) or
from highest to lowest note (“Reverse”).
After setting the parameters as required press [ENTER] to execute
the Chord Sort job. The metronome icon will appear on the display while
the data is being processed, then “Completed” will appear briefly when
the job is done. Press the [EXIT] key to return to the job list, or a mode key
to go directly to the selected mode.
117
9
T h e S o n g J o b s
08 : Chord Separate
Shifts each note in the specified measure range which falls on the
same beat (i.e. chords) forward in order from lowest to highest or vice
versa according to the Chord Sort settings, by the specified number of
clocks, thus “separating” the chord notes by the specified number of
clocks.
First beat.
First measure. Last measure.
Last beat.
The “TR” parameter selects the track to be affected by the Chord
Separate job: “01” … “16”.
The “M” parameters above the graphic bar are used to specify the
first measure:beat and last measure:beat of the range to be modified.
The “Clock” parameter determines the number of clocks by which
the notes of the chord will be separated: “000” through “999”.
After setting the parameters as required press [ENTER] to execute
the Chord Separate job. The metronome icon will appear on the display
while the data is being processed, then “Completed” will appear briefly
when the job is done. Press the [EXIT] key to return to the job list, or a
mode key to go directly to the selected mode.
118
T h e S o n g J o b s
09 : Copy Event
Copies all data from a specified range of measures from one track to
the specified measure in the specified destination track. The copied data
can also be transposed as required. This operation overwrites the data
from the beginning of the specified destination measure with the data from
the source measures. Previous data in the overwritten measures is there-
fore lost.
First beat.
First measure. Last measure.
Last beat.
The upper “TR” parameter selects the source track — i.e. the track
from which the data is to be copied: “01” … “16” for the sequencer
tracks, the accompaniment “Pt” track, the accompaniment “Cd” track, the
“Tm” track, or “Al” (All) tracks. When “Pt”, “Cd”, Tm” or “Al” is selected,
the lower “TR” parameter is automatically set to the same track.
The lower “TR” parameter selects the destination track — i.e. the
track to which the data is to be copied: “01” … “16” for the sequencer
tracks, the accompaniment “Pt” track, the accompaniment “Cd” track, the
“Tm” track, or “Al” (All) tracks. When “Pt”, “Cd”, Tm” or “Al” is selected,
the upper “TR” parameter is automatically set to the same track.
The “M” parameters above the upper graphic bar are used to
specify the first measure:beat and last measure:beat of the range to be
copied.
Chord template
parameter
119
9
T h e S o n g J o b s
The “Transpose” parameter sets a transpose value for the copied
data in semitone increments from “-24” through “+00” to “+24”.
The Chord template parameter, above the upper graphic bar, appears
only when the “Cd” track is selected at the “TR” parameter. This param-
eter specifies which chord progression, either the user chord progression
programmed in the source “Cd” track or preset chord template, will be
copied to the User chord progression.
After setting the parameters as required press [ENTER] to execute
the Copy Event job. The metronome icon will appear on the display while
the data is being processed, then “Completed” will appear briefly when
the job is done. Press the [EXIT] key to return to the job list, or a mode key
to go directly to the selected mode.
NOTE
Previous data in measures overwritten by the Copy Event job will be completely
erased and replaced by the copied data.
The time signature is copied by the Copy Event job, but Voice and Play Effect data
is not copied.
The Copy Event job makes it easy to use phrases or even complete sections (an
entire chorus, for example) in more than one place in a song. You can copy a phrase
played by one voice, and have it repeated by a different voice later in the song. You
can always edit the copied sections to create variations.
The “M” parameters below the lower graphic bar specifiy the
destination measure:beat to which the data will be copied, as well as the
number of times the data is to be copied.
Destination beat.
Destination measure. Number of times to be copied.
120
T h e S o n g J o b s
10 : Erase Event
Erases all note and event data from the specified measure or range
of measures in the specified track. An erase operation leaves the specified
measures intact but blank.
First beat.
First measure. Last measure.
Last beat.
The “TR” parameter selects the track to be affected by the Erase
Event job: “01” … “16” for the sequencer tracks, the accompaniment
“Pt” track, the accompaniment “Cd” track, or the “Tm” track.
The “M” parameters above the graphic bar are used to specify the
first measure:beat and last measure:beat of the range to be erased.
After setting the parameters as required press [ENTER] to execute
the Erase Event job. The metronome icon will appear on the display while
the data is being processed, then “Completed” will appear briefly when
the job is done. Press the [EXIT] key to return to the job list, or a mode key
to go directly to the selected mode.
NOTE
Unlike the Delete Measure job, the Erase Event job erases the data from the
specified measures only in the specified track. Also, the data is erased but the
measures remain intact (i.e. the subsequent measures are not moved back). After
an erase operation you can record new material in the resulting blank measures as
required.
121
9
T h e S o n g J o b s
11 : Extract Event
Allows a specified type of event — note, program change, pitch
bend, control change, channel aftertouch, polyphonic aftertouch, or system
exclusive — to be extracted (removed) from a specified range of measures
in a specified track. The extracted data can be moved to the same range of
measures in any other specified track.
First beat.
First measure. Last measure.
Last beat.
The upper “TR” parameter selects the source track — i.e. the track
from which the event data is to be extracted: “01” … “16”.
The lower “TR” parameter selects the destination track — i.e. the
track to which the extracted event data is to be moved: “01” … “17”, or
“Off” if you simply want to discard the specified event data.
The “M” parameters above the graphic bar are used to specify the
first measure:beat and last measure:beat of the range from which the
event data is to be extracted.
The event type parameter near the upper graphic bar determines the
type of event data to be extracted:
NOTE Note events.
PC Program change events.
PB Pitch bend events.
CC Control change events. When this event type is selected a control
change number parameter appears to the right of the even type.
The control change parameter determines the MIDI control
change number(s) to be extracted: “000” … “127” or “All”.
CAT Channel aftertouch events.
PAT Polyphonic aftertouch events.
EXC Exclusive events.
Event type
parameter
122
T h e S o n g J o b s
After setting the parameters as required press [ENTER] to execute
the Extract Event job. The metronome icon will appear on the display while
the data is being processed, then “Completed” will appear briefly when
the job is done. Press the [EXIT] key to return to the job list, or a mode key
to go directly to the selected mode.
NOTE
Although you can remove events individually in the edit mode (page 192), the
Extract Event job makes it simple to remove all occurences of the specified event
within the specified measure range in one operation. This is particularly convenient
when removing slow pitch bends or volume changes that may employ many
individual events to create a single effect.
If the destination track already contains data, the extracted event data will be
merged.
123
9
T h e S o n g J o b s
12 : Create Continuous
This job makes it possible to create continuous data of the specified
type in order to produce smooth pitch bends, tempo changes, etc.
First beat.
First measure. Last measure.
Last beat.
The “TR” parameter selects the track to be affected by the Create
Continuous job: “01” … “16” for the sequencer tracks, or “Tm” for the
tempo track.
The “M” parameters above the graphic bar are used to specify the
first measure:beat and last measure:beat of the range to be modified.
The data type parameter determines the type of data to be created.
PB Pitch bend events.
CC Control change events. When this event type is selected a control
change number parameter appears to the right of the type
parameter. The control change parameter determines the MIDI
control change number to be created: “000” … “127”.
CAT Channel aftertouch events.
EXC Master volume.
TMP Tempo events (can only be selected for the Tm (Tempo) track).
The “Data” parameters set the range of data values to be created:
the left number sets the starting value and the right number sets the
ending value. The range of values available will depend on the type of
event selected.
The “Clock” parameter sets the spacing between the created
events in clocks: “000” … “999”.
Data type
parameter
124
T h e S o n g J o b s
The “Curve” parameter sets the degree of positive or negative
“curvature” that will be applied to the continuous data: “-16” … “00” …
“+16”.
After setting the parameters as required press [ENTER] to execute
the Create Continuous job. The metronome icon will appear on the display
while the data is being processed, then “Completed” will appear briefly
when the job is done. Press the [EXIT] key to return to the job list, or a
mode key to go directly to the selected mode.
Start point
End point
Curve = +16 Curve = 0 (linear)
Curve = -16
Clock
parameter
125
9
T h e S o n g J o b s
13 : Thin Out
“Thins out” specified types of data by removing every other event of
the specified type. This is particularly useful for reducing the volume of
data required for pitch bends, aftertouch and other control change opera-
tions, thus making more efficient use of the available memory.
First beat.
First measure. Last measure.
Last beat.
The “TR” parameter selects the track to be affected by the Thin Out
job: “01” … “16” for the sequencer tracks, or “Tm” for the tempo track.
The “M” parameters above the graphic bar are used to specify the
first measure:beat and last measure:beat of the range to be modified.
The data type parameter determines the type of data to be thinned.
PB Pitch bend events.
CC Control change events. When this event type is selected a control
change number parameter appears to the right of the type
parameter. The control change parameter determines the MIDI
control change number to be thinned: “000” … “127”.
CAT Channel aftertouch events.
PAT Polyphonic aftertouch events.
TMP Tempo events (can only be selected for the Tm (Tempo) track).
After setting the parameters as required press [ENTER] to execute
the Thin Out job. The metronome icon will appear on the display while the
data is being processed, then “Completed” will appear briefly when the
job is done. Press the [EXIT] key to return to the job list, or a mode key to
go directly to the selected mode.
Data type
parameter
126
T h e S o n g J o b s
14 : Time Stretch
Lenghtens or shortens the specified track by a specified percentage
without affecting tempo or pitch.
The “TR” parameter selects the track to be affected by the Time
Stretch job: “01” … “16” for the sequencer tracks, or “Al” for all se-
quencer tracks.
The “M” parameters above the graphic bar are used to specify the
first measure:beat and last measure:beat of the range to be modified.
The “Time” parameter specifies the percentage by which the time
is to be lengthened or shortened: “50%” … “200%”. Gate time of notes
in the specified track and measures will also be changed in proportion to
this setting.
After setting the parameters as required press [ENTER] to execute
the Time Stretch job. The metronome icon will appear on the display while
the data is being processed, then “Completed” will appear briefly when
the job is done. Press the [EXIT] key to return to the job list, or a mode key
to go directly to the selected mode.
First beat.
First measure. Last measure.
Last beat.
127
9
T h e S o n g J o b s
15 : Create Measure
Creates a specified number of blank measures having the specified
time signature for all tracks. The created measures are inserted at a
specified measure number, and all subsequent measures are moved
forward to make room.
First beat.
First measure. Last measure.
Last beat.
The “M” parameter above the graphic bar specifies the measure at
which the newly created measures will be inserted.
The time signature parameter below the graphic bar determines the
time signature of the measures to be created: 1/16 … 16/16, 1/8 … 16/8,
1/4 … 8/4.
The “Measure” parameter below the bar specifies the number of
measures to be created.
After setting the parameters as required press [ENTER] to execute
the Create Measure job. The metronome icon will appear on the display
while the data is being processed, then “Completed” will appear briefly
when the job is done. Press the [EXIT] key to return to the job list, or a
mode key to go directly to the selected mode.
NOTE
All existing measures after the point at which the new measures are created will be
moved forward to make room for the new measures.
If you use the Create Measure job with an empty song, the specified new
measures will be placed in track 1 only.
Use Create Measure when you want to add new material somewhere in the middle
of data you’ve already recorded, without erasing the existing data. First create the
required measures, then either copy the data from existing measures using the
Copy Event function, or record new data as required.
128
T h e S o n g J o b s
16 : Delete Measure
Deletes the specified range of measures from all tracks simulta-
neously.
The “M” parameters above the graphic bar are used to specify the
first measure and last measure of the range to be deleted.
After setting the parameters as required press [ENTER] to execute
the Delete Measure job. The metronome icon will appear on the display
while the data is being processed, then “Completed” will appear briefly
when the job is done. Press the [EXIT] key to return to the job list, or a
mode key to go directly to the selected mode.
NOTE
Delete Measure is a great way to completely cut out unwanted data from the
song. It’s important to remember, however, that a delete operation affects all
tracks simultaneously, and that measures following the deleted range are moved
back to take the place of the deleted measures.
First measure.
Last measure.
129
9
T h e S o n g J o b s
17 : Copy Track
Copies all data from the specified track to any other specified track.
The upper “TR” parameter selects the source track — i.e. the track
from which the data is to be copied: “01” … “16”.
The lower “TR” parameter selects the destination track — i.e. the
track to which the data is to be copied: “01” … “16”.
The “Event”, “Play Effect”, and “Voice” check boxes make it
possible to specify whether or not the corresponding types of data will be
copied or not (the data is copied when the checkbox is checked).
After setting the parameters as required press [ENTER] to execute
the Copy Track job. The metronome icon will appear on the display while
the data is being processed, then “Completed” will appear briefly when
the job is done. Press the [EXIT] key to return to the job list, or a mode key
to go directly to the selected mode.
NOTE
If the destination track already contains data, the copied track data will erase and
replace the previous data.
130
T h e S o n g J o b s
18 : Mix Track
Combines the data contained in two specified tracks and places the
result in a third track (which can be the same as the second track).
The upper and center “TR” parameters select the first and second
source tracks — i.e. the tracks which are to be mixed: “01” … “16”.
The lower “TR” (“01” … “16”) parameter specifies the destination
track to which the mixed data is to be copied.
After setting the parameters as required press [ENTER] to execute
the Mix Track job. The metronome icon will appear on the display while the
data is being processed, then “Completed” will appear briefly when the
job is done. Press the [EXIT] key to return to the job list, or a mode key to
go directly to the selected mode.
NOTE
If there is no data in the second source track, the data from the first source track is
simply copied to the destination track.
131
9
T h e S o n g J o b s
19 : Clear Track
Completely clears the specifed track from the currently selected
song (including all Play Effect parameters).
The “TR” parameter selects the track(s) to be cleared: “01” … “16”
for the sequencer tracks, the accompaniment “Pt” track, the accompani-
ment “Cd” track, the “Tm” track, or “Al” (All) tracks.
The “Event”, “Play Effect”, and “Voice” check boxes make it
possible to specify whether or not the corresponding types of data will be
cleared or not (the data is cleared when the checkbox is checked).
After setting the parameters as required press [ENTER] to execute
the Clear Track job. The metronome icon will appear on the display while
the data is being processed, then “Completed” will appear briefly when
the job is done. Press the [EXIT] key to return to the job list, or a mode key
to go directly to the selected mode.
132
T h e S o n g J o b s
20 : Expand Backing
“Expands” the accompaniment track data — i.e. the pattern and
chord data — and places the results in the normal sequencer tracks after
converting the data to standard MIDI format. The expanded data is placed
in sequencer tracks 9 through 16 (see chart below). Any previous data in
those tracks will be erased!
Press [ENTER] to execute the Expand Backing job. The metronome
icon will appear on the display while the data is being processed, then
“Completed” will appear briefly when the job is done. Press the [EXIT] key
to return to the job list, or a mode key to go directly to the selected mode.
Pattern Track Sequencer Track
D1 9
D2 10
PC 11
BA 12
C1 13
C2 14
C3 15
C4 16
NOTE
If the “Ds3” (Drum set 3) is assigned to the D1, D2 or PC track of the expanded
pattern, the drum voice settings will be copied to “Ds2” (Drum set 2). The previous
settings in Ds2 will be overwritten (erased).
133
9
T h e S o n g J o b s
21 : Normalize
Actually applies the Play Effect settings to the sequence data,
modifying the sequence data accordingly. The Play Effect settings are
initialized after execution.
The “TR” parameter selects the track(s) to be affected by the
Normalize job: “01” … “16” for the sequencer tracks, or “Al” (All) for all
sequencer tracks.
After setting the parameter as required press [ENTER] to execute
the Normalize job. The metronome icon will appear on the display while
the data is being processed, then “Completed” will appear briefly when
the job is done. Press the [EXIT] key to return to the job list, or a mode key
to go directly to the selected mode.
134
T h e S o n g J o b s
22 : Copy Song
Copies all data from all tracks of the specified song to any other
specified song (including song name, play effect and voice assignment
settings).
The upper “Song” parameter selects the source song — i.e. the
song from which the data is to be copied: “01” … “20”.
The lower “Song” parameter selects the destination song — i.e. the
song to which the data is to be copied: “01” … “20”
After setting the parameters as required press [ENTER] to execute
the Copy Song job. The metronome icon will appear on the display while
the data is being processed, then “Completed” will appear briefly when
the job is done. Press the [EXIT] key to return to the job list, or a mode key
to go directly to the selected mode.
NOTE
If the destination song already contains data, the copied song will erase and replace
the previous song.
135
9
T h e S o n g J o b s
23 : Clear Song
Completely clears all data from all tracks of the currently selected
song. Also initializes the play effect and voice settings.
The “Song” parameter selects the song to be cleared: “01” … “20”
or “Al”(All)
After setting the parameter as required press [ENTER] to execute
the Clear Song job. The metronome icon will appear on the display while
the data is being processed, then “Completed” will appear briefly when
the job is done. Press the [EXIT] key to return to the job list, or a mode key
to go directly to the selected mode.
NOTE
Clearing “All” songs can not be undone with the “Undo/Redo” job.
136
T h e S o n g J o b s
24 : Song Name
Allows an original name of up to 8 characters to be assigned to the
current song.
To enter a character, use the cursor keys to move the cursor to the
character to be entered, then press the [ENTER] key. The character will
appear at the character cursor location and the character cursor will ad-
vance to the next character position.
The character cursor can be moved by pressing the function key to
the right of “
To delete a character, press the function key to the right of “del”.
The character to the left of the cursor will be deleted and the cursor will
move to the deleted character’s position.
When the name has been entered press the [EXIT] key to return to
the job list, or a mode key to go directly to the selected mode (it is not
necessary to press the [ENTER] key to enter the specified name).
NOTE
Entering a song name can not be undone with the “Undo/Redo” job.
137
10
C r e a t i n g O r i g i n a l A c c o m p a n i m e n t P a t t e r n s
C r e a t i n g O r i g i n a l
A c c o m p a n i m e n t P a t t e r n s
QY70 accompaniment patterns are created by combining
“phrases” — either preset or original — in the PATTERN mode. A
phrase is simply an individual “part” of a pattern — e.g. a drum
phrase, a bass phrase, a keyboard phrase, etc. — using a single voice.
The QY70 has 4,167 preset phrases, and 384 memory locations for
original patterns (i.e., 64 user styles, each with independent INTRO,
MAIN A, MAIN B, FILL AB, FILL BA, and ENDING sections).
You can also see phrase components of the preset patterns in
the PATTERN mode.
The Preset Phrases
The QY70 has a total of 4,167 preset phrases that can be combined
to create a virtually endless variety of accompaniment patterns. The preset
phrase numbers have three sections, as shown below. The cursor can be
placed at any of these three sections to select as required.
Category
Beat
Number
138
C r e a t i n g O r i g i n a l A c c o m p a n i m e n t P a t t e r n s
Category
Da Drum-a (Pop&Rock)
Db Drum-b (Specific)
Fa Drum Fill-a (Pop&Rock)
Fb Drum Fill-b (Specific)
PC Percussion
Ba Bass-a (Pop&Rock)
Bb Bass-b (Specific)
Ga Guitar Chord-a
(Pop&Rock)
Gb Guitar Chord-b
(Specific)
GR Guitar Riff
KC Keyboard Chord
KR Keyboard Riff
PD Pad
BR Brass
SE Sound Effects
Beat
16 Beat
8 Beat
3/4 Beat
Number
Differs depending on the category
NOTE
For details on the phrase category, beat and number, refer to the Preset
Phrase List.
139
10
C r e a t i n g O r i g i n a l A c c o m p a n i m e n t P a t t e r n s
Combining Phrases In the Pattern Mode
The phrases are combined to create patterns which can be used in
accompaniments in the PATTERN mode.
Z Select the PATTERN Mode, a User Style, & a Section
Press the [PATT] key to select the PATTERN mode then,
with the cursor located at the style number, select a “user” style:
“U00” through “U64”. Also move the cursor to the section name
and select the section you want to create.
X Set the Pattern Length, Time Signature & Tempo as
Required
If you’re starting with an empty pattern, move the cursor
to the pattern length parameter and set the desired pattern
length from 1 to 8 measures. If necessary, also move the cursor
to the time signature parameter and set as required (1/16 … 16/
16, 1/8 … 16/8, 1/4 … 8/4). The default tempo is 120, but you can
move the cursor to the tempo parameter and set any other
tempo that is suitable for your pattern.
Style number
Section
Tempo
Time signature
Pattern length
140
C r e a t i n g O r i g i n a l A c c o m p a n i m e n t P a t t e r n s
V Enter the Required Phrase Number
Use the cursor keys to move to the category, beat, or
number parameter, then use the [-1] and [+1] keys or the SHIFT-
Number entry method to select the desired phrase for that track.
Cursor at D1 track
Move the cursor to the phrase-entry area of the track you
want to assign a phrase to.
NOTE
The default pattern length for the INTRO, MAIN A, MAIN B, and
ENDING sections is 2 measures, while the default length for the FILL
AB and FILLBA sections is 1 measure.
C Select a Pattern Track
Phrases can be assigned to any of 8 “tracks” in the
PATTERN mode. The PATTERN mode tracks and the phrases that
can be assigned to each track are listed below:
Track Part Available Phrases
D1 Drum 1 Drums Phrase
D2 Drum 2 Drums Phrase
PC Percussion Percussion Phrase
BA Bass Bass Phrase
C1 Chord 1
Chord backing phrase (Guitar, Keyboard, etc.)
C2 Chord 2
Chord backing phrase (Guitar, Keyboard, etc.)
C3 Chord 3
Chord backing phrase (Guitar, Keyboard, etc.)
C4 Chord 4
Chord backing phrase (Guitar, Keyboard, etc.)
NOTE
For details on the available phrases, refer to the Preset Phrase List.
141
10
C r e a t i n g O r i g i n a l A c c o m p a n i m e n t P a t t e r n s
Category
Beat
Number
Phrase Name
Monitoring the Pattern
If you press the [
W
] button while entering phrases you can
hear how the pattern sounds as the various phrases are
added. Press [
A
] to stop playback.
Muting & Soloing the Pattern Tracks
One or more PATTERN mode tracks can be muted or
soloed by placing the cursor immediately to the left of the
track (in the velocity-meter position) and using the [-1] or
[+1] to mute or solo the track as required. Use the [-1] key
to alternately mute or un-mute the selected track, or the
[+1] key to alternately solo or un-solo the track. Any
number of tracks can be muted and/or soloed at a time. To
solo more than one track at a time hold the [SHIFT] key
while soloing additional tracks after the first solo track has
been specified. Also hold the [SHIFT] key while un-soloing
a single track when multiple tracks are soloed (un-soloing a
single track without holding the [SHIFT] key will un-solo all
soloed tracks).
If the assigned
phrase is longer
than the pattern
length, this symbol
( ) appears. In this
case, the exceeded
part of the phrase
will not be played.
142
C r e a t i n g O r i g i n a l A c c o m p a n i m e n t P a t t e r n s
The letter “M” appears next to tracks that are muted, and
the letter “S” appears when a track is soloed.
Mute
Solo
Clearing Phrases
Phrases can be cleared by placing the cursor at the appro-
priate phrase number, catgory, or beat and pressing the
function key next to “Cler” on the display.
Changing the Pattern Playback Chord
The chord used for pattern playback can be changed by
placing the cursor at the chord location and entering the
chord via the micro-keyboard and [ENTER] keys as de-
scribed on page 40. The bass note for “on-bass” chords
can be entered via the lower octave of the micro-keyboard
while holding the [OCT DOWN/BASS] key (the bass note
will appear to the right of a slash next to the chord name).
143
10
C r e a t i n g O r i g i n a l A c c o m p a n i m e n t P a t t e r n s
You can also enter the chord by pressing the chord as it is
on the micro keyboard or an external keyboard if
“FNGR”(Fingered Chord function) is set to “ON”. In this
case, a bass note can be entered by pressing a key for a
bass note on the left part of the micro keyboard or an
external keyboard while holding the chord. (The “left part”
range for entering a bass note can be specified in the
Utility mode on page 227.)
B Repeat for as Many Tracks as Necessary
Repeat steps C and V to enter phrases for as many
tracks as required (you don’t have to program all 8 pattern tracks).
N Repeat for the Other Sections
Repeat the above procedure to complete the remaining
sections of the style, as required.
NOTE
See “The Pattern Jobs” on page 157 for details on the QY70's pattern
jobs which allow considerable versatility in creating and modifying
patterns.
You can also re-combine phrases on the preset pattern. To store the re-
combination, execute the “Copy Pattern” (page 189) or “Copy Track”
(page 186) job before changing the style number of the pattern.
144
C r e a t i n g O r i g i n a l A c c o m p a n i m e n t P a t t e r n s
Recording Original Phrases
The QY70 makes it easy to create original accompaniment phrases.
The PATTERN mode provides two ways to create original phrases: realtime
and step recording.
Realtime Phrase Recording
In the realtime record mode you select the track you want to record,
the voice you want to record with, and then play the part on the micro-
keyboard or an external MIDI keyboard in real time.
Z Select a User Style and Section
As described in the preceding section, begin by selecting a
user style (“U01” through “U64”) and a section (“INTRO”,
“MAIN A”, etc.) in the PATTERN mode.
User style
Section
X Select a Source Chord
Move the cursor to the chord parameter and use the chord
entry procedure described above to enter the “source chord” for
the phrase you are recording (i.e. the chord on which the phrase
is based). Note that you can not enter an “on-bass” chord for the
“source chord”.
145
10
C r e a t i n g O r i g i n a l A c c o m p a n i m e n t P a t t e r n s
Source chord
C Select a Pattern Track and its “User” Phrase
Move the cursor to the track you want to create an original
phrase for. To create a bass phrase, for example, select the “BA”
(Bass) track. Then use the [+1] key to select the user phrase for
that track (“Us-
-001” for Intro section’s D1 track through “Us-
-
048” for Ending section’s C4 track, depending on the selected
section and track.) If the track you intend to record is empty, you
need not select the user phrase for that track.
“User” phrase
NOTE
Before engaging the record mode you can also set the micro-keyboard
“velocity” via the “VEL” parameter in the upper right corner of the
display. The velocity can be set in ten levels — the more bars the
higher the velocity. There are also four “randon velocity” settings
which produce different degrees of random velocity variation. “R1
produces the smallest variation and “R4” produces the greatest
variation.
You can also set the micro-keyboard’s octave before engaging the
record mode by pressing [OCT UP] or [OCT DOWN] key.
146
C r e a t i n g O r i g i n a l A c c o m p a n i m e n t P a t t e r n s
V Engage the Phrase Record Ready Mode
Press the [
S
] key to engage the phrase record ready mode.
The red LED will light, and the display will appear something like
this:
B Select the Realtime Overdub Record Mode
Move the cursor to the record mode selector area of the
display (the area with the “OVER” and “STEP” buttons), and
move it to the “OVER” (realtime overdub) button, then press the
[+1/YES] key to select the realtime overdub record mode (if it
isn’t already selected). An inverse “R” will appear in the selected
record mode button.
N Set the Phrase Type and Voice
Note that a default “TYPE” and voice are shown for the
selected track. These can be changed as required before record-
ing the phrase. The default types and voices for each pattern
track are shown below. The “TYPE” parameter is actually the
“Note Transition Table Type” and it determines how the corre-
sponding track will be re-harmonized when used in an accompa-
niment with chord changes. The various phrase types are de-
scribed below.
Record mode
selector
147
10
C r e a t i n g O r i g i n a l A c c o m p a n i m e n t P a t t e r n s
Track Default Type Default Voice
D1 (Drum 1) Bypass Dr 001: Standard Kit
D2 (Drum 2) Bypass Dr 001: Standard Kit
PC (Percussion) Bypass Dr 001: Standard Kit
BA (Bass) Bass Ba 033: Acoustic Bass
C1 (Chord 1) Chord 1 Pf 001: Grand Piano
C2 (Chord 2) Chord 1 Pf 001: Grand Piano
C3 (Chord 3) Chord 1 Pf 001: Grand Piano
C4 (Chord 4) Chord 1 Pf 001: Grand Piano
The Phrase Types
Bypass The phrase is not re-harmonized — i.e. it is not
affected by chord changes — when this type is
selected. This type should be used for drum and
percussion phrases, otherwise the drum instruments
will be “re-harmonized” and change whenever a
chord change is encountered.
Bass When the “Bass” type is selected the phrase is re-
harmonized in the same way as for the Chord 1
phrase type, below, except that the root is always
used as the first note immediately following a chord
change. In the case of an “on-bass” chord, the bass
phrase always plays the “on-bass” note.
Chord 1 The source note data is reharmonized based on the
root of the specified chord.
Chord 2 The source note data is re-harmonized with the
closest possible “voice leading” from the preceding
chord. This results in the smoothest possible chord
changes.
Parallel When this type is selected the source note data is
simply transposed to the root of the new chord
without re-harmonization.
VoiceType
148
C r e a t i n g O r i g i n a l A c c o m p a n i m e n t P a t t e r n s
M Set the Pattern Length, Time Signature & Tempo as
Required
If you’re creating a phrase for an empty pattern, move the
cursor to the pattern length parameter and set the desired
pattern length from 1 to 8 measures. If necessary, also move the
cursor to the time signature parameter and set as required (1/16
… 16/16, 1/8 … 16/8, 1/4 … 8/4). The default tempo is 120, but
you can move the cursor to the tempo parameter and set any
other tempo that is suitable for your recording.
< Record
Press the [
W
] key to begin recording. The metronome will
sound and you’ll be given a one-measure count-in prior to the first
measure actually recorded.
Play the required part either on the micro-keyboard or via
an external MIDI keyboard. The phrase will continuously repeat
from the first to last measure, so you can continue to add notes
until the current part is complete.
NOTE
Since your original phrase will be automatically re-harmonized as
required by the QY70 ABC system, there are a few rules you should
follow to ensure the best results:
1: Stick to the harmonic environment of your source chord.
2: Use primarily the root, 3rd, 5th, and major 7th.
3: Keep it rhythmic … avoid melodic lines.
Pattern length
Time signature
Tempo
149
10
C r e a t i n g O r i g i n a l A c c o m p a n i m e n t P a t t e r n s
> Delete Mistakes as Required
To delete mistakes, simply play the note to be deleted on
either the micro-keyboard or an external MIDI keyboard while
holding the [SHIFT] key. All corresponding notes that occur while
the key is held will be deleted.
? Stop Recording
Press the [
A
] key to stop recording. The normal PATTERN
play mode is automatically re-selected when you stop recording.
[ Repeat for as Many Tracks and Sections as Necessary
Repeat the appropriate steps of the above procedure to
record phrases for as many tracks and sections as required.
NOTE
See “The Pattern Jobs” on page 157 for details on the QY70’s pattern
jobs which allow considerable versatility in creating and modifying
patterns.
150
C r e a t i n g O r i g i n a l A c c o m p a n i m e n t P a t t e r n s
Step Phrase Recording
The step phrase record mode lets you enter phrases note-by-note,
with precise control over the timing, length, and loudness of each note.
You can record complete phrases using the step mode, or use it to brush-
up and add data to an existing phrase.
Steps Z through M are the same as for phrase realtime recording,
above, except for step B in which you’ll need to select the “STEP” record
mode rather than “OVER” (page 146). The actual recording process is then
the same as step-recording the SONG tracks except that the measure/
beat/clock display shows the total number of measures in the pattern as
well as the current measure number. Refer to pages 81 through 87 for
details on step recording.
“STEP” button
NOTE
The recorded user phrase can be cleared by pressing the function key next to
“cler”, as shown on page 142. In this case, you can recall the cleared phrase by
selecting a user phrase for that track again with [+1]/[-1] key. To delete the recorded
phrase completely, execute the “Clear Track” job on page 188.
151
10
C r e a t i n g O r i g i n a l A c c o m p a n i m e n t P a t t e r n s
For details on each parameter of the VOICE mixer display, see “The
Song Voice Mode” on page 61. Remember that each track’s voice assign,
pan and volume settings for a preset pattern in the VOICE mode will not be
stored in memory.
Pattern Voice mode
Each pattern phrase has its own voice whether it is a preset phrase
or a user phrase. (The user phrase voice is specified in the phrase record
ready mode described on page 146).
However, you can also assign any of the QY70’s 519 voices and 20
drum kits to the 8 pattern phrase tracks(D1, D2, PC, BA, C1...C4) via the
PATTERN VOICE mode.
The VOICE mode features a graphic on-screen “mixer” that has
mute/solo controls, pan pots, and faders for each track. The PATTERN
voice mode also provides access to effect send controls and a versatile
range of voice editing parameters.
Press the [PATT] key to select the voice mode mixer display. The
mixer display shows 8 pattern phrase tracks at a time.
The VOICE mode mixer display looks almost the same as that of the
SONG VOICE mode except:
Voice parameter for
each track shows “-
-”
as the default setting,
which means that the
phrase has its own
voice assigned to each
track.
The track numbers are D1, D2, PC,
BA and C1...C4.
Master volume and Pattern
volume faders are omitted.
152
C r e a t i n g O r i g i n a l A c c o m p a n i m e n t P a t t e r n s
The Effect Send Display
The QY70 features a high-performance internal digital signal process-
ing system which provides a range of effects including reverb, delay,
modulation, distortion, and more. Three independent effect blocks are
provided — Reverb, Chorus, and Variation. The individual effects are
selected and modified via the EFFECT mode, described in detail on page
212. The VOICE mode mixer display provides access to independent effect
send controls for each of the three effect blocks via the MENU sub-display.
Press the [MENU] button, and then the function key next to “Effect Send”
on the display.
153
10
C r e a t i n g O r i g i n a l A c c o m p a n i m e n t P a t t e r n s
The Effect Send display looks almost the same as that of the SONG
VOICE mode’s Effect Send display except for track numbers and the
assigned voice (“-
-” means the phrase has its own voice).
For details on each parameter of the Effect Send display, see “The
Effect Send Display” of the Song Voice mode on page 66.
154
C r e a t i n g O r i g i n a l A c c o m p a n i m e n t P a t t e r n s
Voice Editing
The QY70’s VOICE EDIT mode allows you to modify the sound of
the voices assigned to each track to best suit your particular musical
requirements. The VOICE EDIT mode can be accessed from the PATTERN
VOICE mode by pressing the [MENU] button, and then the function key
next to “Voice Edit” on the display. If a Drum Set is selected (i.e., if a drum
track, to which “Ds3” drum set voice is assigned, is selected) the “Drum
Voice Edit” mode will also be available via the menu.
NOTE
“Ds1” and “Ds2” drum sets can be selected in the SONG VOICE mode only. In the
PATTERN VOICE mode, “Ds3” drum set can be selected to edit drum instruments.
The VOICE EDIT display looks almost the same as that of the SONG
VOICE mode’s VOICE EDIT display except for track numbers and the
assigned voice (“-
-” means the phrase voice has its own voice).
For details on each parameter of the VOICE EDIT display, see “Voice
Editing” of the Song Voice mode on page 68.
155
10
C r e a t i n g O r i g i n a l A c c o m p a n i m e n t P a t t e r n s
Play Effects
The QY70’s “Play Effects” can also affect pattern playback in real
time as well as song playback, and are not actually recorded with the
phrase data. The Play Effects include Groove Quantization and Drum Table
Remapping.
To access the Play Effects press the [MENU] key while in the
PATTERN play mode and press the function key next to “Play Fx” on the
display. The “Groove” and “Drum Table” displays can then be selected by
pressing the [MENU] key and then the function key next to “Groove” or
“Drum Table” on the display, as required.
NOTE
The Play Effects settings can be stored for each user style. These settings will also
be effective when the user style is assigned and played in the SONG mode’s
pattern (Pt) track.
156
C r e a t i n g O r i g i n a l A c c o m p a n i m e n t P a t t e r n s
“Groove” and “Drum Table” displays are exactly the same as those
in the SONG mode except track numbers (D1, D2, PC, BA, C1...C4). See
“Play Effects” of the SONG mode on page 94 for details.
Groove Quantization display
Drum Table display
157
T h e P a t t e r n J o b s
11
T h e P a t t e r n J o b s
The PATTERN mode includes 24 pattern “jobs” that perform a
variety of important functions. To access and use the pattern jobs,
press the [MENU] key while in the main PATTERN mode, then press
the “Job” function key. This calls the pattern job list. You can select
any job on the list simply by moving the cursor to the required job and
pressing [ENTER]. The function keys can be used to move the cursor
directly to the first job in the corresponding category: Event, Phrase,
Track, or Pattern (press the [MENU] key, then the appropriate function
key).
158
T h e P a t t e r n J o b s
Returning to the PATTERN Mode
The [EXIT] key can be used to exit from any pattern job, and then from the job list
thereby returning you to the normal PATTERN mode. You can also press the [PATTERN]
key to directly return to the PATTERN mode.
00: Undo/Redo
“Event” category
01: Quantize
02: Modify Velocity
03: Modify Gate Time
04: Crescendo
05: Transpose
06: Shift Clock
07: Chord Sort
08: Chord Separate
09: Copy Event
10: Erase Event
11 : Extract Event
12: Create Continuous
13: Thin Out
14: Time Stretch
“Phrase” category
15: Copy Phrase
16: Get Phrase
17: Put Phrase
“Track” category
18: Copy Track
19: Mix Track
20: Clear Track
“Pattern” category
21: Copy Pattern
22: Clear Pattern
23: Style Name
159
T h e P a t t e r n J o b s
11
00 : Undo/Redo
This job will “undo” any other pattern/song job, edit, or record
function if it is executed before any other operation is performed. In all
cases the affected data is restored to the state it was in before performing
the job, edit, or record operation. This job will also undo the last undo
operation (redo).
The name of the last operation performed will appear on the display
(i.e. the operation which will be “undone”). In the example display, above,
a quantize operation will be undone.
Press [ENTER] to execute the Undo/Redo job. The metronome icon
will appear on the display while the data is being processed, then “Com-
pleted” will appear briefly when the job is done. Press the [EXIT] key to
return to the job list, or a mode key to go directly to the selected mode.
DETAIL
The UNDO/REDO job will not undo the Clear Song (“All”), the Clear Pattern (“All”
styles), the Song Name, or Style Name jobs.
Name of the last
operation performed
160
T h e P a t t e r n J o b s
01 : Quantize
Aligns notes in the specified track to or close to the nearest speci-
fied beat.
Quantize Values
Value Effect
Aligns to the nearest 32nd note.
Aligns to the nearest 16th note triplet.
Aligns to the nearest 16th note.
Aligns to the nearest 8th note triplet.
Aligns to the nearest 8th note.
Aligns to the nearest quarter note triplet.
Aligns to the nearest quarter note.
The “TR” parameter selects the track to be affected by the Quantize
job: D1, D2, PC, BA, C1, C2, C3, C4.
The “M” parameters above the graphic bar are used to specify the
first measure:beat and last measure:beat of the range to be quantized.
The “Quantize” parameter determines to what beats the note data
in the specified track will be aligned. If you select “ ”, for example, all
notes in the track will be aligned to the nearest 16th-note beat, to a degree
determined by the “Strength” parameter.
First beat.
First measure. Last measure.
Last beat.
161
T h e P a t t e r n J o b s
11
The “Strength” parameter determines how “strongly” the notes
are attracted to the specified quantize value. The strength range is from
0% to 100%. At a setting of “0%” no quantization will occur, while a
setting of “100%” will cause all notes to be aligned precisely to the
nearest specified beat value. In-between settings produce a corresponding
shift in the position of all off-beat notes to the nearest specified beat value.
With a value setting of “ ” and a strength setting of 50%, for example, a
note that does not fall precisely on a quarter note beat will be shifted about
halfway to nearest quarter note beat.
Aligns to the nearest 16th note + 16th note triplet.
Aligns to the nearest 8th note + 8th note triplet.
The “Swing Rate” parameter produces a “swing” feel by shifting
the timing of “back beats”, as specified by the quantize value. For ex-
ample, if the specified quantization value is 8th notes, then the swing
effect will shift the 2nd, 4th, 6th, and 8th beats of each measure forward
to create a swing feel. If the quantize value is set to a triplet note length,
the last note in each triplet group will be shifted. If the quantize value is set
to a compound note length (e.g. 8th note + 8th note triplet) the even-
numbered back beats will be shifted. The “Swing Rate” parameter deter-
mines how much the timing of the affected notes will be shifted. The
range is from 50% (no swing) to 75% (maximum swing) for even note
lengths, from 66% to 83% for triplet note lengths, and from 50% to 66%
for even-plus-triplet note lengths (e.g. 8th note + 8th note triplet).
Original data (assuming 4/4 meter)
Quantizing strength = 100% (quantize value = )
Quantizing strength = 50% (quantize value = )
162
T h e P a t t e r n J o b s
The “Gate Time” parameter increases or decreases the gate times
(length) of all notes affected by the swing parameter. The range is from 0%
to 200%. The “Gate Time” parameter sets the ratio between the shorter
and longer gate time values. A setting of “100%” maintains the original
relationship between the notes, lower values produce a narrower gate time
range, and higher values produce a broader gate time range.
After setting the parameters as required press [ENTER] to execute
the Quantize job. The metronome icon will appear on the display while the
data is being processed, then “Completed” will appear briefly when the
job is done. Press the [EXIT] key to return to the job list, or a mode key to
go directly to the selected mode.
Original timing
Quantizing value = , Swing rate 50% (no delay)
Quantizing value = , Swing rate 60% (delay applied)
Quarter-note length
163
T h e P a t t e r n J o b s
11
02 : Modify Velocity
Increases or decreases the velocity values of all notes in the speci-
fied track and range of measures.
The “TR” parameter selects the track to be affected by the Modify
Velocity job: D1, D2, PC, BA, C1, C2, C3, C4.
The “M” parameters above the graphic bar are used to specify the
first measure:beat and last measure:beat of the range to be modified.
The “SetAll” parameter makes it possible to set all notes in the
specified range to a single velocity value from “1” to “127”. “Set All” can
also be turned “Off” when the “Rate” and “Offset” parameters, below,
are to be used for velocity modification.
The “Rate” parameter allows you to change the Velocity value of
each note without affecting the velocity ratios between notes (proportional
change). A setting of
“100%” maintains the
absolute velocity differ-
ences between notes,
while lower (higher) values
will decrease (increase)
the velocity values to the
corresponding percentage,
resulting in a narrower
(wider) dynamic range.
The range is from “0%” to
“200%”.
96 64 32 127 96
48 32 16 63 48
127 96 48 127 127
Original
velocities
Rate = 50%
Rate = 150%
First beat.
First measure. Last measure.
Last beat.
164
T h e P a t t e r n J o b s
New Velocity = Original Velocity x rate/100 + offset
(If the right side of the equation is 0 or less, the New Velocity
becomes 1. If the right side of the equation is 128 or more, the New
Velocity becomes 127.)
After setting the parameters as required press [ENTER] to execute
the Modify Velocity job. The metronome icon will appear on the display
while the data is being processed, then “Completed” will appear briefly
when the job is done. Press the [EXIT] key to return to the job list, or a
mode key to go directly to the selected mode.
NOTE
The Modify Velocity job is a great way to “soften” the sound of material that has
too great a variation between the softest and loudest notes, or, conversely, to add
extra punch to dull-sounding material. Experiment with the parameters to get a feel
for what they do.
The “Offset” parameter allows you to change all velocity values by
an absolute amount. “-” settings will decrease the velocity of each note by
the corresponding amount, “+” settings will increase the velocity accord-
ingly. The range is from “-99” through “0” to “+99”.
96 64 32 127 96
76 44 12 107 76
116 84 52 127 116
Original
velocities
Offset = -20
Offset = +20
165
T h e P a t t e r n J o b s
11
03 : Modify Gate Time
Increases or decreases the gate times (length) of all notes in the
specified track and range of measures.
The “TR” parameter selects the track to be affected by the Modify
Gate Time job: D1, D2, PC, BA, C1, C2, C3, C4.
The “M” parameters above the graphic bar are used to specify the
first measure:beat and last measure:beat of the range to be modified.
The “SetAll” parameter makes it possible to set all notes in the
specified range to a single gate time value from “1” to “9999”. “Set All”
can also be turned “Off” when the “Rate” and “Offset” parameters,
below, are to be used for gate time modification.
The “Rate” parameter allows you to change the Gate Time value of
each note without affecting the gate time ratios between notes (propor-
tional change). A setting of “100%” maintains the absolute gate time
differences between notes, while lower (higher) values will decrease
(increase) the gate time values to the corresponding percentage. The range
is from “0%” to “200%”.
32 32 32 48 48
16 16 16 24 24
48 48 48 72 72
Original
gate time
Rate = 50%
Rate = 150%
First beat.
First measure. Last measure.
Last beat.
166
T h e P a t t e r n J o b s
New Gate Time = Original Gate Time x rate/100 + offset
(If the right side of the equation is 0 or less, the New Gate Time
becomes 1)
After setting the parameters as required press [ENTER] to execute
the Modify Gate Time job. The metronome icon will appear on the display
while the data is being processed, then “Completed” will appear briefly
when the job is done. Press the [EXIT] key to return to the job list, or a
mode key to go directly to the selected mode.
NOTE
The Modify Gate Time job can be used to produce a more staccato or legato feel,
as required. Experiment with the parameters to get a feel for what they do.
32 32 32 48 48
12 12 12 28 28
52 52 52 68 68
Original
gate time
Offset = -20
Offset = +20
The “Offset” parameter allows you to change all gate time values by
an absolute amount. “-” settings will decrease the gate time of each note
by the corresponding amount, “+” settings will increase the gate time
accordingly. The range is from “-9999” through “0” to “+9999”.
167
T h e P a t t e r n J o b s
11
04 : Crescendo
Produces a gradual crescendo (increase in note velocity) or decre-
scendo (decrease in note velocity) in the specified track over the specified
range of measures.
The “TR” parameter selects the track to be affected by the Cre-
scendo job: D1, D2, PC, BA, C1, C2, C3, C4.
The “M” parameters above the graphic bar are used to specify the
first measure:beat and last measure:beat of the range to be modified.
The “Range” parameter determines the range of velocity values
over which the crescendo will occur. A setting of “+24”, for example, will
cause the MIDI velocity values to increase by 24 over the specified mea-
sure range (The MIDI velocity value range is from 1 to 127).
Negative values cause a corresponding decrease in velocity, thereby
producing a decrescendo rather than a crescendo. The range of this
parameter is from “-99” through “0” to “+99”.
Specified measure (“M”) range.
Range +24.
Crescendo.
Original
velocity.
First beat.
First measure. Last measure.
Last beat.
168
T h e P a t t e r n J o b s
After setting the parameters as required press [ENTER] to execute
the Crescendo job. The metronome icon will appear on the display while
the data is being processed, then “Completed” will appear briefly when
the job is done. Press the [EXIT] key to return to the job list, or a mode key
to go directly to the selected mode.
169
T h e P a t t e r n J o b s
11
05 : Transpose
Transposes all notes in the specified part up or down by the speci-
fied number of semitones.
The “TR” parameter selects the track to be affected by the Trans-
pose job: D1, D2, PC, BA, C1, C2, C3, C4.
The “M” parameters above the graphic bar are used to specify the
first measure:beat and last measure:beat of the range to be modified.
The “Note” parameters specify the range of notes to be affected.
The maximum range is from “C-2” to “G8”.
The “Transpose” parameter determines the amount of transposi-
tion in semitone increments. Minus (-) values transpose down while plus
(+) values transpose up. the range is from “-99” through “0” to “+99”.
After setting the parameters as required press [ENTER] to execute
the Transpose job. The metronome icon will appear on the display while
the data is being processed, then “Completed” will appear briefly when
the job is done. Press the [EXIT] key to return to the job list, or a mode key
to go directly to the selected mode.
First beat.
First measure. Last measure.
Last beat.
170
T h e P a t t e r n J o b s
06 : Shift Clock
Moves all notes and events in the specified track and range of
measures forward or backward by the specified number of clocks (480
clocks per 1/4 note).
The “TR” parameter selects the track to be affected by the Shift
Clock job: D1, D2, PC, BA, C1, C2, C3, C4.
The “M” parameters above the graphic bar are used to specify the
first measure:beat and last measure:beat of the range to be modified.
The “Clock” parameter determines the direction and number of
clocks by which the notes in the specified measure range will be shifted.
“+” settings shift the notes forward (toward the end of the pattern) and “-
” settings shift the notes backward (toward the beginning of the pattern).
The range is from “-9999” through “0000” to “+9999”.
After setting the parameters as required press [ENTER] to execute
the Shift Clock job. The metronome icon will appear on the display while
the data is being processed, then “Completed” will appear briefly when
the job is done. Press the [EXIT] key to return to the job list, or a mode key
to go directly to the selected mode.
First beat.
First measure. Last measure.
Last beat.
171
T h e P a t t e r n J o b s
11
NOTE
The Shift Clock job will not shift data beyond the specified measure range.
Therefore, events near the beginning of the specified range may sound “bunched”
together and events near the end of the specified range may be “cut off” in some
cases.
Since the Shift Clock job actually shifts the timing of all notes and other events in
the specified measures forward or backward, it can significantly alter the “feel” of
the pattern. You could move the notes forward (“+” settings) to create a more “laid
back” feel, or backward (“-” settings) to produce a more “driving” feel. Of course,
you can also use Shift Clock to correct timing that is off in the first place.
172
T h e P a t t e r n J o b s
07 : Chord Sort
Sorts all notes in the specified measure range which fall on the
same beat (i.e. chords) so that the notes are arranged in order from lowest
to highest or from highest to lowest.
The “TR” parameter selects the track to be affected by the Chord
Sort job: D1, D2, PC, BA, C1, C2, C3, C4.
The “M” parameters above the graphic bar are used to specify the
first measure:beat and last measure:beat of the range to be modified.
The “Type” parameter determines whether the chords in the
specified range are arranged from lowest to highest note (“Normal”) or
from highest to lowest note (“Reverse”).
After setting the parameters as required press [ENTER] to execute
the Chord Sort job. The metronome icon will appear on the display while
the data is being processed, then “Completed” will appear briefly when
the job is done. Press the [EXIT] key to return to the job list, or a mode key
to go directly to the selected mode.
First beat.
First measure. Last measure.
Last beat.
173
T h e P a t t e r n J o b s
11
08 : Chord Separate
Shifts each note in the specified measure range which falls on the
same beat (i.e. chords) forward in order from lowest to highest or vice
versa according to the Chord Sort settings, by the specified number of
clocks, thus “separating” the chord notes by the specified number of
clocks.
The “TR” parameter selects the track to be affected by the Chord
Separate job: D1, D2, PC, BA, C1, C2, C3, C4.
The “M” parameters above the graphic bar are used to specify the
first measure:beat and last measure:beat of the range to be modified.
The “Clock” parameter determines the number of clocks by which
the notes of the chord will be separated: “000” through “999”.
After setting the parameters as required press [ENTER] to execute
the Chord Separate job. The metronome icon will appear on the display
while the data is being processed, then “Completed” will appear briefly
when the job is done. Press the [EXIT] key to return to the job list, or a
mode key to go directly to the selected mode.
First beat.
First measure. Last measure.
Last beat.
174
T h e P a t t e r n J o b s
09 : Copy Event
Copies all data from a specified range of measures to the selected
place in the same track. The copied data can also be transposed as re-
quired. This operation overwrites the data from the beginning of the
specified destination measure with the data from the source measures.
Previous data in the overwritten measures is therefore lost.
The upper “TR” parameter selects the source track — i.e. the track
from which the data is to be copied: D1, D2, PC, BA, C1, C2, C3, C4.
The “M” parameters above the upper graphic bar are used to
specify the first measure:beat and last measure:beat of the range to be
copied.
First beat.
First measure. Last measure.
Last beat.
175
T h e P a t t e r n J o b s
11
The “Transpose” parameter sets a transpose value for the copied
data in semitone increments from “-24” through “+00” to “+24”.
After setting the parameters as required press [ENTER] to execute
the Copy Event job. The metronome icon will appear on the display while
the data is being processed, then “Completed” will appear briefly when
the job is done. Press the [EXIT] key to return to the job list, or a mode key
to go directly to the selected mode.
NOTE
Previous data in measures overwritten by the Copy Event job will be completely
erased and replaced by the copied data.
The “M” parameters below the lower graphic bar specifiy the
destination measure:beat to which the data will be copied, as well as the
number of times the data is to be copied.
Destination beat.
Destination measure. Number of times to be copied.
176
T h e P a t t e r n J o b s
10 : Erase Event
Erases all note and event data from the specified measure or range
of measures in the specified track. An erase operation leaves the specified
measures intact but blank.
The “TR” parameter selects the track to be affected by the Erase
Event job: D1, D2, PC, BA, C1, C2, C3, C4.
The “M” parameters above the graphic bar are used to specify the
first measure:beat and last measure:beat of the range to be erased.
After setting the parameters as required press [ENTER] to execute
the Erase Event job. The metronome icon will appear on the display while
the data is being processed, then “Completed” will appear briefly when
the job is done. Press the [EXIT] key to return to the job list, or a mode key
to go directly to the selected mode.
NOTE
The Erase Event job erases the data from the specified measures only in the
specified track. Also, the data is erased but the measures remain intact (i.e. the
subsequent measures are not moved back). After an erase operation you can
record new material in the resulting blank measures as required.
First beat.
First measure. Last measure.
Last beat.
177
T h e P a t t e r n J o b s
11
11 : Extract Event
Allows a specified type of event — note, program change, pitch
bend, control change, channel aftertouch, polyphonic aftertouch, or system
exclusive — to be extracted (removed) from a specified range of measures
in a specified track. The extracted data can be moved to the same range of
measures in any other specified track.
The upper “TR” parameter selects the source track — i.e. the track
from which the event data is to be extracted: D1, D2, PC, BA, C1, C2, C3,
C4.
The lower “TR” parameter selects the destination track — i.e. the
track to which the extracted event data is to be moved: D1, D2, PC, BA,
C1, C2, C3, C4, or “Off” if you simply want to discard the specified event
data.
The “M” parameters above the graphic bar are used to specify the
first measure:beat and last measure:beat of the range from which the
event data is to be extracted.
The event type parameter near the upper graphic bar determines the
type of event data to be extracted:
Event type
parameter
First beat.
First measure. Last measure.
Last beat.
178
T h e P a t t e r n J o b s
NOTE Note events.
PC Program change events.
PB Pitch bend events.
CC Control change events. When this event type is selected a control
change number parameter appears to the right of the even type.
The control change parameter determines the MIDI control
change number(s) to be extracted: “000” … “127” or “All”.
CAT Channel aftertouch events.
PAT Polyphonic aftertouch events.
EXC Exclusive events.
After setting the parameters as required press [ENTER] to execute
the Extract Event job. The metronome icon will appear on the display while
the data is being processed, then “Completed” will appear briefly when
the job is done. Press the [EXIT] key to return to the job list, or a mode key
to go directly to the selected mode.
NOTE
Although you can remove events individually in the edit mode (page 192), the
Extract Event job makes it simple to remove all occurences of the specified event
within the specified measure range in one operation. This is particularly convenient
when removing slow pitch bends or volume changes that may employ many
individual events to create a single effect.
If the destination track already contains data, the extracted event data will be
merged.
179
T h e P a t t e r n J o b s
11
12 : Create Continuous
This job makes it possible to create continuous data of the specified
type in order to produce smooth pitch bends, aftertouch, etc.
The “TR” parameter selects the track to be affected by the Create
Continuous job: D1, D2, PC, BA, C1, C2, C3, C4.
The “M” parameters above the graphic bar are used to specify the
first measure:beat and last measure:beat of the range to be modified.
The data type parameter determines the type of data to be created.
PB Pitch bend events.
CC Control change events. When this event type is selected a control
change number parameter appears to the right of the type
parameter. The control change parameter determines the MIDI
control change number to be created: “000” … “127”.
CAT Channel aftertouch events.
EXC Master volume.
The “Data” parameters set the range of data values to be created:
the left number sets the starting value and the right number sets the
ending value. The range of values available will depend on the type of
event selected.
The “Clock” parameter sets the spacing between the created
events in clocks: “000” … “999”.
Data type
parameter
First beat.
First measure. Last measure.
Last beat.
180
T h e P a t t e r n J o b s
The “Curve” parameter sets the degree of positive or negative
“curvature” that will be applied to the continuous data: “-16” … “00” …
“+16”.
After setting the parameters as required press [ENTER] to execute
the Create Continuous job. The metronome icon will appear on the display
while the data is being processed, then “Completed” will appear briefly
when the job is done. Press the [EXIT] key to return to the job list, or a
mode key to go directly to the selected mode.
Start point
End point
Curve = +16 Curve = 0 (linear)
Curve = -16
Clock
parameter
181
T h e P a t t e r n J o b s
11
13 : Thin Out
“Thins out” specified types of data by removing every other event of
the specified type. This is particularly useful for reducing the volume of
data required for pitch bends, aftertouch and other control change opera-
tions, thus making more efficient use of the available memory.
The “TR” parameter selects the track to be affected by the Thin Out
job: D1, D2, PC, BA, C1, C2, C3, C4.
The “M” parameters above the graphic bar are used to specify the
first measure:beat and last measure:beat of the range to be modified.
The data type parameter determines the type of data to be thinned.
PB Pitch bend events.
CC Control change events. When this event type is selected a control
change number parameter appears to the right of the type
parameter. The control change parameter determines the MIDI
control change number to be thinned: “000” … “127”.
CAT Channel aftertouch events.
PAT Polyphonic aftertouch events.
After setting the parameters as required press [ENTER] to execute
the Thin Out job. The metronome icon will appear on the display while the
data is being processed, then “Completed” will appear briefly when the
job is done. Press the [EXIT] key to return to the job list, or a mode key to
go directly to the selected mode.
Data type
parameter
First beat.
First measure. Last measure.
Last beat.
182
T h e P a t t e r n J o b s
14 : Time Stretch
Lenghtens or shortens the specified track by a specified percentage
without affecting tempo or pitch.
First beat.
First measure. Last measure.
Last beat.
The “TR” parameter selects the track to be affected by the Time
Stretch job: D1, D2, PC, BA, C1, C2, C3, C4.
The “M” parameters above the graphic bar are used to specify the
first measure:beat and last measure:beat of the range to be modified.
The “Time” parameter specifies the percentage by which the time
is to be lengthened or shortened: “50%” … “200%”. The gate time of
notes in the specified track and measures will also be changed in propor-
tion to this setting.
After setting the parameters as required press [ENTER] to execute
the Time Stretch job. The metronome icon will appear on the display while
the data is being processed, then “Completed” will appear briefly when
the job is done. Press the [EXIT] key to return to the job list, or a mode key
to go directly to the selected mode.
NOTE
If the specified track is shortened, the phrase of the track will play repeatedly to fill
the pattern length.
If the specified track is lengthened, the exceeding part of the phrase will be cut off.
183
T h e P a t t e r n J o b s
11
15 : Copy Phrase
Copies the specified preset phrase to a specified PATTERN mode
track as a user phrase.
The “Phrase” parameter selects the source phrase — i.e. the preset
phrase to be copied (preset phrase numbers have three sections which can
be specified: category, beat, and number — page 137).
The “TR” parameter selects the destination track: D1, D2, PC, BA,
C1, C2, C3, C4.
After setting the parameters as required press [ENTER] to execute
the Copy Phrase job. The metronome icon will appear on the display while
the data is being processed, then “Completed” will appear briefly when
the job is done. Press the [EXIT] key to return to the job list, or a mode key
to go directly to the selected mode.
NOTE
If the specified preset phrase is shorter than the pattern length, the phrase will be
copied repeatedly to fill the pattern length.
If the specified preset phrase is longer than the pattern length, the exceeding part
of the copied phrase will be cut off.
If the destination track already contains data, the copied phrase will erase and
replace the previous phrase data.
184
T h e P a t t e r n J o b s
16 : Get Phrase
Copies the data from the specified range of measures in the speci-
fied track of a specified song to the specified phrase.
The “Song” parameter selects the source song — i.e. the song
from which the data is to be copied: “01” … “20”.
The “TR” parameter selects the song source track — i.e. the track
from which the data is to be copied: “01” … “16”.
The “M” parameters above the upper graphic bar are used to
specify the first measure and last measure of the range to be copied.
The lower “TR” parameter specified the track to which the data is
to be copied: D1, D2, PC, BA, C1, C2, C3, C4.
After setting the parameters as required press [ENTER] to execute
the Get Phrase job. The metronome icon will appear on the display while
the data is being processed, then “Completed” will appear briefly when
the job is done. Press the [EXIT] key to return to the job list, or a mode key
to go directly to the selected mode.
NOTE
The Get Phrase job is a convenient way to create new phrases by copying a few
appropriate measures from songs.
If the destination track already contains data, the copied data will erase and replace
the previous phrase data.
First measure.
Last measure.
185
T h e P a t t e r n J o b s
11
17: Put Phrase
Copies the phrase data from a specified pattern track to the speci-
fied measures in the specified track of a specified song.
The “Pattern TR” parameter specified the source pattern track: D1,
D2, PC, BA, C1, C2, C3, C4.
The “Song” parameter selects the destination song — i.e. the song
to which the phrase data is to be copied: “01” … “20”.
The “TR” parameter selects the destination song track — i.e. the
track to which the phrase data is to be copied: “01” … “16”.
The “M” parameter specifies the measure of the destination track to
which the phrase data is to be copied.
After setting the parameters as required press [ENTER] to execute
the Put Phrase job. The metronome icon will appear on the display while
the data is being processed, then “Completed” will appear briefly when
the job is done. Press the [EXIT] key to return to the job list, or a mode key
to go directly to the selected mode.
NOTE
The time signature of the phrase will not affect the time signature of the song.
If the destination song track contains data, the copied phrase data will erase and
replace the previous song track data.
The source pattern data is re-harmonized to the current chord specified in the
PATTERN play mode before being copied to the destination song track.
186
T h e P a t t e r n J o b s
18 : Copy Track
Copies all data from the specified track in the specified section of
the specified style to any other specified track in the specified section of
the specified style.
The upper “Style” parameter specifies the source style: “001” …
“128”, “U01” … “U64”.
The upper “Section” parameter specifies the source section:
“Intro”, “MainA”, “MainB”, “FillAB”, “FillBA”, “Ending”.
The upper “TR” parameter selects the source track — i.e. the track
from which the data is to be copied: D1, D2, PC, BA, C1, C2, C3, C4.
The lower “Style” parameter specifies the destination style: “U01”
… “U64”.
The lower “Section” parameter specifies the destination section:
“Intro”, “MainA”, “MainB”, “FillAB”, “FillBA”, “Ending”.
The lower “TR” parameter selects the destination track — i.e. the
track to which the data is to be copied: D1, D2, PC, BA, C1, C2, C3, C4.
After setting the parameters as required press [ENTER] to execute
the Copy Track job. The metronome icon will appear on the display while
the data is being processed, then “Completed” will appear briefly when
the job is done. Press the [EXIT] key to return to the job list, or a mode key
to go directly to the selected mode.
NOTE
If the destination track already contains data, the copied data will erase and replace
the previous data.
187
T h e P a t t e r n J o b s
11
19 : Mix Track
Combines the data contained in two specified tracks and places the
result in a third track (which can be the same as the second track).
The upper and center “TR” parameters select the first and second
source tracks — i.e. the tracks which are to be mixed: D1, D2, PC, BA, C1,
C2, C3, C4.
The lower “TR” parameter specifies the destination track to which
the mixed data is to be copied: D1, D2, PC, BA, C1, C2, C3, C4.
After setting the parameters as required press [ENTER] to execute
the Mix Track job. The metronome icon will appear on the display while the
data is being processed, then “Completed” will appear briefly when the
job is done. Press the [EXIT] key to return to the job list, or a mode key to
go directly to the selected mode.
NOTE
If there is no data in the second source track, the data from the first source track is
simply copied to the destination track.
Even if a preset phrase is previously assigned to the destination track, it will be
mixed with the first source track and become a user phrase.
188
T h e P a t t e r n J o b s
20 : Clear Track
Completely clears the specifed track in the specified section.
The “Section” parameter specifies the section to be cleared:
“Intro”, “MainA”, “MainB”, “FillAB”, “FillBA”, “Ending”.
The “TR” parameter selects the track to be cleared: D1, D2, PC, BA,
C1, C2, C3, C4.
The “Event”, “Play Effect”, and “Voice” check boxes make it
possible to specify whether or not the corresponding types of data will be
cleared or not (the data is cleared when the checkbox is checked).
After setting the parameters as required press [ENTER] to execute
the Clear Track job. The metronome icon will appear on the display while
the data is being processed, then “Completed” will appear briefly when
the job is done. Press the [EXIT] key to return to the job list, or a mode key
to go directly to the selected mode.
189
T h e P a t t e r n J o b s
11
21 : Copy Pattern
Copies all data from the specified section of the specified style to
any other specified section of the specified style.
The upper “Style” parameter specifies the source style: “001” …
“128”, “U01” … “U64”.
The upper “Section” parameter specifies the source section:
“Intro”, “MainA”, “MainB”, “FillAB”, “FillBA”, “Ending” and “All”.
The lower “Style” parameter specifies the destination style: “U01”
… “U64”.
The lower “Section” parameter specifies the destination section:
“Intro”, “MainA”, “MainB”, “FillAB”, “FillBA”, “Ending” and “All”.
After setting the parameters as required press [ENTER] to execute
the Copy Pattern job. The metronome icon will appear on the display while
the data is being processed, then “Completed” will appear briefly when
the job is done. Press the [EXIT] key to return to the job list, or a mode key
to go directly to the selected mode.
NOTE
If the destination pattern contains data, the copied data will erase and replace the
previous pattern data.
190
T h e P a t t e r n J o b s
22 : Clear Pattern
Completely clears all data from the specified section of the specified
style.
The “Style” parameter specifies the style: “U01” … “U64” and
“All”.
The “Section” parameter specifies the section of the style to be
cleared: “Intro”, “MainA”, “MainB”, “FillAB”, “FillBA”, “Ending” and
“All”.
After setting the parameter as required press [ENTER] to execute
the Clear Pattern job. The metronome icon will appear on the display while
the data is being processed, then “Completed” will appear briefly when
the job is done. Press the [EXIT] key to return to the job list, or a mode key
to go directly to the selected mode.
NOTE
Clearing “All” styles can not be undone with the “Undo/Redo” job.
191
T h e P a t t e r n J o b s
11
23 : Style Name
Allows an original name of up to 8 characters to be assigned to the
current style.
To enter a character, use the cursor keys to move the cursor to the
character to be entered, then press the [ENTER] key. The character will
appear at the character cursor location and the character cursor will ad-
vance to the next character position.
The character cursor can be moved by pressing the function key to
the right of “ ”.
To delete a character, press the function key to the right of “del”.
The character to the left of the cursor will be deleted and the cursor will
move to the deleted character’s position.
When the name has been entered press the [EXIT] key to return to
the job list, or a mode key to go directly to the selected mode (it is not
necessary to press the [ENTER] key to enter the specified name).
NOTE
You can enter “name” not only for the user style but also for the preset style. If you
want to store a newly entered “name” for the preset style, execute the “Copy
Pattern” Job before changing the style number.
Entering a style name can not be undone with the “Undo/Redo” job.
192
E d i t i n g S o n g s & P a t t e r n s
E d i t i n g S o n g s
& P a t t e r n s
The QY70’s editing capability makes it easy to correct mis-
takes made when recording song or pattern phrase data, and to
generally refine your sound.
The song and pattern edit “change” mode lets you individually
modify the timing, pitch, gate time (length) and velocity (loudness) of
each note or other events in the song or pattern. There’s also an edit
“insert” that allows insertion of note, program change, sustain on/off,
pitch bend, modulation, pan, volume, expression, and other events at
any point in the song or pattern.
Engaging the SONG or PATTERN Edit Mode
To engage the edit mode, place the cursor at the track you want to
edit in the normal SONG or PATTERN mode, press the [MENU] key, and
then the function key next to [Edit] on the display.
193
E d i t i n g S o n g s & P a t t e r n s
12
The edit display will look something like this (of course, the note
data will be different).
Song Edit Display
Track being edited
Top of song
One note per line
Location (beat-clock)
Note (pitch)
Gate time (beat-clock)
Velocity
Current measure number
194
E d i t i n g S o n g s & P a t t e r n s
The pattern edit display is almost exactly the same. The only differ-
ences are the name of the track being edited and the current measure
display.
Pattern Edit Display
If you place the cursor at the “Pt”(pattern) or “Cd”(chord) track in
the SONG mode and engage the edit mode, the edit display will be exactly
the same as the step recording display described on page 54.
Track being edited
Current measure number
Top of pattern
One note per line
Location (beat-clock)
Note (pitch)
Gate time (beat-clock)
Velocity
Current measure number
and the pattern length
195
E d i t i n g S o n g s & P a t t e r n s
12
Moving Around
The location, pitch, gate time, and velocity values for each note are
shown on a single line of the display. The notes are arranged in order from
top to bottom. You can move around within the song or pattern by simply
moving the cursor. Move below the bottom of the display and the note
data will scroll down, moving towards the end of the song or pattern. The
opposite occurs when you move up above the top of the display.
In addition to the lines of note data, there are markers for the top of
the song/pattern and the end of the song/pattern. Measure lines are
indicated by solid lines between lines of note data (non-measure bound-
aries between lines of data appear as dotted lines).
End of song
Measure line
Cursor currently
in measure 8
196
E d i t i n g S o n g s & P a t t e r n s
Change Mode Editing
The “Change” edit mode is initially selected when the edit mode is
engaged. To edit any note or other event in the song or pattern, simply
move the cursor to the appropriate line, and then to the required parameter
within that line. The [-1] and [+1] keys can then be used to select a new
value for the selected parameter. The edited line will flash when any
parameter within it is changed. This indicates that a change has been made
but has not yet been entered. Press the [ENTER] key to actually enter the
changes, or move the cursor to another line to cancel the changes.
The available parameters depend on the selected event type. The
note event parameters are listed below. See “Insert Mode Editing” (page
197) for other event types.
Beat-clock
The first column contains the note location data. The left number is
the beat within the current measure (1 through 4 in a 4/4 measure,
for example.), and the right number is the clock within that beat (000
through 479 in case of 1/4-note beat). The beat and clock values can
be selected and edited independently.
Pitch
This is the actual pitch of the note. The range is from C-2 to G8.
Gate Time
Gate time is the length of the note in beats and clocks. The number
to the left of the colon is 1/4-beats and the number to the right is
clocks within a 1/4-beat. A normal 1/4 note, for example, is 432
clocks long. This is about 90% of the actual length of a 1/4-note
division, which is 480 clocks. The “normal” length of the note is
slightly shortened to prevent notes from running into each other and
sounding slurred ( a slur is produced by setting the full note length).
The beat-clock range is from 00:001 to 99:479.
VelocityGate timePitchBeat-clock
197
E d i t i n g S o n g s & P a t t e r n s
12
Velocity
This parameter controls the velocity (loudness) of the note. The
range is from 001 to 127.
Deleting Events
Notes and other events (sustain on/off, pitch bend, etc.) can be
deleted by placing the cursor at the line corresponding to the event
to be deleted, and then pressing the function key next to “del” on
the display.
Insert Mode Editing
The edit insert mode is used to insert new notes and other events at
a specified location in the song or pattern.
Z Place the cursor at the insert location.
Move the cursor to the edit line correponding to (or near
to) the location at which you want to insert the new data.
Place cursor at
insert location
X Engage the insert edit mode.
Press the [MENU] key and then the function key next to
“Insert” on the display to switch to the insert edit mode.
198
E d i t i n g S o n g s & P a t t e r n s
C Select an Event Type to Insert, and Set the Event Pa-
rameters
If the display corresponding to the type of event you want
to insert does not appear immediately, use the [-1] and [+1] keys
to select the desired event type.
All events have at least two parameters — usually the
location of the event (Measure-Beat-Clock) and the event value.
Move the cursor to the event parameters and set as required by
using the [-1] and [+1] keys or the SHIFT-Number entry method
where appropriate.
Note
New notes can be inserted at any specified location. The
note range is from “C-2” to “G8”. Gate time and velocity
can also be specified.
199
E d i t i n g S o n g s & P a t t e r n s
12
PB (Pitch Bend)
Pitch bend events can be used to produce pitch bend
effects. The pitch bend values correspond to pitch bend
wheel positions from “-8192” (lowest position) through
“+0000” (center) to “+8191” (highest position). To pro-
duce smooth pitch bends you’ll need to insert several
small pitch bend events at appropriate intervals. Remem-
ber to use more pitch bend events to return the pitch to
normal after a bend.
Location
Value
Location
Pitch
Gate time
Velocity
PC (Program Change)
Program change events can be used to switch voices at
any point in the track.
The Bank Select (MSB and LSB) parameters are used for
200
E d i t i n g S o n g s & P a t t e r n s
bank selection when selecting XG voices. Refer to the XG
Normal/Drum voice list in the List Book for details.
Bank Select MSB
Bank Select LSB
Location
Voice name
Program change number
Note that the program number in the XG Normal/Drum
voice list (refer to the List Book) and the MIDI program
change number is different: i.e., the program number for
“Grand Piano” is “1” while its MIDI program change
number is”0”. (Program numbers, which are defined in
General MIDI, range 1 - 128, while MIDI program change
numbers range 0 - 127.)
Location
Control change number
Control change value
CC (Control Change)
Any MIDI control change number from 000 through 127
can be entered with an appropriate control value where
applicable. Control change numbers are used for modula-
tion, volume, panning, expression and other control
functions. Some control change numbers are assigned to
specific functions and some are not. Refer to the “MIDI
Data Format” section of the manual (refer to the List Book)
for details.
201
E d i t i n g S o n g s & P a t t e r n s
12
CAT (Channel Aftertouch)
Inserts a channel aftertouch message with the specified
aftertouch value.
Location Aftertouch value
PAT (Polyphonic Aftertouch)
Inserts a polyphonic aftertouch message for the specified
note with the specified aftertouch value.
PAT aftertouch events affect a single specified note, as
opposed to CAT aftertouch events which affect all notes on
the same channel (track) simultaneously
Location
Note
Aftertouch value
202
E d i t i n g S o n g s & P a t t e r n s
RPN
Inserts RPN data. RPN is an abbreviation for “Registered
Parameter Number”, which is a MIDI message used to
control part settings such as pitch bend sensitivity, tuning,
etc. Refer to the “MIDI Data Format” section of the
manual (refer to the List Book) for details.
NRPN
Inserts NRPN data. NRPN is an abbreviation for “Non
Registered Parameter Number”, which is a MIDI message
used to control voice settings such as vibrato, filter,
envelope generator, drum setup, etc. Refer to the “MIDI
Data Format” section of the manual (refer to the List Book)
for details.
Location
NRPN MSB
NRPN LSB
Location
RPN MSB
RPN LSB
Data entry MSB
Data entry LSB
Data entry MSB
203
E d i t i n g S o n g s & P a t t e r n s
12
Exc (Exclusive)
Inserts a System Exclusive message in hexadecimal
format. Refer to the “MIDI Data Format” section of the
manual (refer to the List Book) for details.
Hexadecimal Number Entry
Use the [SHIFT] and the micro-keyboard to enter hexadecimal
values.
Press a black key while holding the [SHIFT] key to enter the
corresponding number.
Press a white key in the left-hand section of the micro-keyboard
(E - D except G) while holding the [SHIFT] key to enter the
corresponding character, “A” through “F”.
After entering a hexadecimal value in one space, move the
cursor to the next space and enter the next value.
Remember to enter “F7” at the end of every exclusive
message.
Location Data (in hexadecimal,
begins with “F0” and
ends with “F7”)
204
E d i t i n g S o n g s & P a t t e r n s
XG NRPN
Inserts NRPN (Non Registered Parameter Number) data
using an XG parameter name (“NRPN”, above, needs to
be entered using numbers). Refer to the “MIDI Data
Format” section of the manual (refer to the List Book) for
details.
Location
Data
RPN parameter name
Location
Data
NRPN parameter name
* “Note” appears if a drum setup parameter is selected
to specify a drum instrument.
XG RPN
Inserts RPN (Registered Parameter Number) data using an
XG parameter name (“RPN”, above, needs to be entered
using numbers). Refer to the “MIDI Data Format” section
of the manual (refer to the List Book) for details.
205
E d i t i n g S o n g s & P a t t e r n s
12
XG Exc System
Inserts a System Exclusive (XG System) message using an
XG parameter name (“Exc”, above, needs to be entered
using hexadecimal values). Refer to the “MIDI Data
Format” section of the manual (refer to the List Book) for
details.
XG Exc Effect
Inserts a System Exclusive (XG Effect) message using an
XG parameter name (“Exc”, above, needs to be entered
using hexadecimal values). Refer to the “MIDI Data
Format” section of the manual (refer to the List Book) for
details.
Location
Data
XG System parameter name
Location
Data/Type
XG Effect parameter name
206
E d i t i n g S o n g s & P a t t e r n s
XG Exc Multi
Inserts a System Exclusive (XG Multi part) message using
an XG parameter name (“Exc”, above, needs to be entered
using hexadecimal values). Refer to the “MIDI Data
Format” section of the manual (refer to the List Book) for
details.
XG Exc Drum
Inserts a System Exclusive (XG Drum setup) message
using an XG parameter name (“Exc”, above, needs to be
entered using hexadecimal values). Refer to the “MIDI
Data Format” section of the manual (refer to the List Book)
for details.
Tempo Change (Tempo track (Tm) only)
Inserts tempo change data with the specified tempo value
(25.0 - 300.0).
Location
Tempo
Location
Data
XG Multi part parameter name
Part
Location
Note
XG Drum setup parameter name
Drum set
Data
207
E d i t i n g S o n g s & P a t t e r n s
12
V Enter the Specified Event
Press the [ENTER] key to enter the event as specified.
B Return to the Change Edit Mode
Press the [EXIT] key to return to the change edit display,
and continue editing as required.
N Exit From the Edit Mode
Press the [SONG] or [PATT] key to exit from the EDIT
mode and return to the normal SONG or PATTERN play mode.
The [EXIT] key will also return you to the SONG or PATTERN
mode from the EDIT mode.
NOTE
If you insert Control Change data other than Modulation (#1), Expres-
sion (#11), Harmonic Content (#71) and Brightness (#74) in the user
pattern, these data will not be reset even if the pattern is changed, and
will take effect on the newly selected pattern.
To avoid this, remember to enter the value to reset at the end of the
phrase when you insert these control change data.
Pitch bend event
inserted. once
inserted, you can edit
the event’s location
and value in the
change edit mode.
208
E d i t i n g S o n g s & P a t t e r n s
XG View
The XG View function displays XG-related events (RPN, NRPN,
System Exclusive, etc.) using the name defined by the XG format. To
engage the XG View function press the [MENU] key while in the EDIT
mode, then press the function button next to “XG View” on the display.
When the box to the left of “XG View” is checked, XG-related
events will be displayed using the corresponding XG format name.
If the box is not checked, XG-related events will be displayed as MSB/LSB
values, or as hexadecimal numbers.
Press [+1] key to check the XG View box, or the [-1] key to uncheck
the box.
209
E d i t i n g S o n g s & P a t t e r n s
12
View Filter
The View Filter lets you “filter out” specified types of events so that
they don’t appear in the EDIT mode display. To access the View Filter press
the [MENU] key while in the EDIT mode, then press the function button
next to “View Filter” on the display.
When the check box beside an event type is checked, that events
will be displayed in the EDIT display. Event types that are not checked will
not appear in the EDIT display.
To filter out a certain type of event, simply move the cursor to the
corresponding check box and press the [-1] key to “uncheck” the box (or
the [+1] key to check the box, as necessary).
The “Set All” function key checks all boxes at once, while the “Clear
All” function key clears all check boxes.
The View Filter Event Types
Abbreviation Event Type
Note Note
PB Pitch Bend
PC Program Change
CC Control Change
CAT Channel Aftertouch
PAT Polyphonic Aftertouch
RPN Registered Parameter Number
NRPN Non Registered Parameter Number
Exc System Exclusive
The “sunglasses”
appear if any events
are “unchecked”.
210
E d i t i n g S o n g s & P a t t e r n s
Phrase Table (Pattern Edit Only)
Phrase Table lets you edit phrase settings for the pattern track
currently being edited.
To access the Phrase Table function press the [MENU] key while in
the EDIT mode, then press the function button next to “Phrase Table” on
the display.
Type
Phrase voice
Source chord
Low limit
High limit
Current chord
Fingered chord
High key
To edit a Phrase Table parameter, move the cursor to the parameter
and edit using the [-1] and [+1] buttons, the SHIFT-Number entry method,
or the micro keyboard as necessary. Only the “CURRENT CHORD” and
“FNGR” parameters can be edited for preset phrases.
TYPE
Selects the phrase (note transition) type: Chord 1, Chord 2, Bass,
Bypass or Parallel. Refer to “The Phrase Types” on page 147 for
information on the various phrase types.
PHRASE VOICE
Selects the voice to be used in the phrase. Refer to the XG Normal/
Drum voice list in the List Book.
211
E d i t i n g S o n g s & P a t t e r n s
12
SOURCE CHORD
Sets the source chord for the phrase (i.e. the chord on which the
phrase is based). Note that you can not enter an “on-bass” chord for
the source chord.
LO LIMIT
HI LIMIT
Sets the note range over which the re-harmonized phrase will be
played (C-2 through G8). If any re-harmonized phrase notes exceed
the range set here, the notes will be automatically shifted up or
down in octave steps so that they fall within the specified range.
CURRENT CHORD
Shows the currently selected chord for the PATTERN play mode.
The current chord can be changed here.
FNGR (Fingered Chord)
Shows the current Fingered Chord setting, ON or OFF. The ON/OFF
setting can be changed here.
HI KEY
Selects the highest root (C through B) in case the phrase (note
transition) type is either Chord 1 or Bass.
212
E f f e c t s & E f f e c t E d i t i n g
Song Mode Effect Connection Display
Reverb effect
Chorus effect
Chorus-to-Reverb
send control
Variation effect
Variation effect INSERTION/
SYSTEM selector
Variation-to-Reverb
send control
Variation-to-Chorus
send control
(Variation effect: SYSTEM)
E f f e c t s
& E f f e c t E d i t i n g
Accessing & Editing the Effect Parameters
The EFFECT connection display and the effect edit displays can be
accessed from the SONG or PATTERN mode as follows:
The QY70 features a versatile internal effects system which
consists of three independent effect stages: REVERB, CHORUS, and
VARIATION. Of these the REVERB and CHORUS stages function as
“system effects”, and the VARIATION stage can be used either as a
system or “insertion” effect. See the signal-flow digrams on page
214 for the difference between “system” and “insertion” effects.
Z Select the Effect Connection Display
Press the [SONG] or [PATT] key as many times as neces-
sary until the SONG or PATTERN effect connection display
appears.
213
13
E f f e c t s & E f f e c t E d i t i n g
Pattern Mode Effect Connection Display
Variation effect
Variation-to-Reverb
send control
Variation-to-Chorus
send control
Reverb effect
Chorus effect
Chorus-to-Reverb
send control
Variation effect
Variation effect INSERTION/
SYSTEM selector
(Variation effect: INSERTION)
Note that in the PATTERN mode effect connection display
only the variation stage has accessible controls. The reverb type
for the PATTERN mode effect is always “HALL 1” and the chorus
type is always “CHORUS 1”.
214
E f f e c t s & E f f e c t E d i t i n g
X Set the Effect Parameters As Required
Move the cursor to the desired parameter and use the [-1]
and [+1] keys to set the selected parameter as required. The
REVERB, CHORUS, and VARIATION effect parameters let you
select any of the available effect types for each stage.
The VARIATION stage INSERTION/SYSTEM selector
determines whether the VARIATION stage functions as an
insertion effect or system effect. Refer to the “Effect Signal
Flow” diagrams and text, below. (In the PATTERN mode effect
connection display, the VARIATION stage is always used as a
system effect that applies to all 8 tracks for the pattern)
Effect Signal Flow
The following diagrams should help you to understand how
the QY70 effect stages relate to overall signal flow.
The signal from each part (track) of the tone generator is
sent to the reverb, chorus and variation stages. The reverb
and chorus effects are always connected as “System”
effects, which means that they affect all parts (tracks). The
effect depth for each track can be varied via the “RE-
VERB” and “CHORUS” send controls in the EFFECT
SEND display (page 66). The chorus stage “TO REV”
parameter can be used to send some or all of the output
from the chorus stage to the reverb stage.
The variation effect can be applied either to one specific
part (track) when it is connected as an “Insertion” effect,
or all parts (tracks) when it is connected as a “System”
effect.
215
13
E f f e c t s & E f f e c t E d i t i n g
VARIATION
REVERB
LINE OUT/
PHONES
CHORUS
TO REV
Track 1
Track 2
Track 3
Track 16
REVERB
LINE OUT/
PHONES
TO REV
TO CHO TO REV
CHORUS
VARIATION
Track 1
Track 2
Track 3
Track 16
When the Variation Stage is an Insertion Effect
In this case the variation effect is applied to one specific
part (track) with “Dry/Wet” mixing capability available in
“Vari. Edit” (See “Effect Editing” on page 216). The track
to which the variation effect is to be applied can be se-
lected via the EFFECT SEND display (page 66).
When the Variation Stage is a System Effect
In this case the variation effect is applied to all parts
(tracks). The variation stage “TO REV” and “TO CHO”
parameters can be used to send some or all of the output
from the variation stage to the reverb and chorus stages.
Variation send level and “Dry/Wet” mixing for each track
can be varied via the controls in the EFFECT SEND display
(page 66).
216
E f f e c t s & E f f e c t E d i t i n g
Song Mode Effect
Connection Display
Pattern Mode Effect
Connection Display
Effect Editing
The Reverb Edit, Chorus Edit, and Variation Edit displays can be
accessed from the Effect Connection display by pressing the [MENU] key
and then the function key next to “Reverb Edit”, “Chorus Edit”, or “Vari.
Edit” on the display. Note that only “Vari. Edit” is available from the
PATTERN mode Effect Connection display.
Use the “Type” parameter near the top of the display to select the
effect type for the current effect stage (REVERB, CHORUS, or VARIA-
TION). Each effect will have different parameters which will appear in the
lower section of the display. Move the cursor to the various parameters
and set as required via the [-1] and [+1] keys. Refer to the “Effect Type
List” and the “Effect Parameter List” (refer to the List Book) for a com-
plete list of the parameters available for each effect and their ranges.
217
13
E f f e c t s & E f f e c t E d i t i n g
Reverb Edit Display Chorus Edit Display Variation Edit Display
How the Variation Effect works in the SONG mode
Please, remember that the variation effect settings in the
SONG effect connection and edit display become ineffective if a song
containing “Pt”(pattern track) data is played. In this case, the variation
effect settings for the pattern used in the song (which is set in the
PATTERN effect connection and edit display) will be used.
To use the variation effect settings in the SONG effect connec-
tion and edit display, play a song consisting of only sequencer track
(1...16) data. It’s sometimes useful to execute Expand Backing job on
page 132 to “expand” pattern track data to the sequencer tracks.
NOTE
These effect displays can be used to edit not all the parameters but the main
parameters given for each effect type. (Refer to the “Effect Parameter List” in the
List Book.) To edit the effect in detail, send the appropriate system exclusive
message to the QY70’s tone generator section.
U t i l i t y F u n c t i o n s
218
U t i l i t y F u n c t i o n s
The QY70 utility mode includes a number of functions that
are important for general operation — e.g. MIDI data handling,
interfacing with external equipment, saving song and pattern data to
an external storage device, ABC system operation, etc.
Accessing the Utility Mode
The utility mode can be accessed from the SONG or PATTERN
mode. Simply press the [MENU] key and then the function key next to
“Utility” on the display.
219
14
U t i l i t y F u n c t i o n s
Once the utility mode has been selected, any of the four utility
displays can be called by pressing the [MENU] key and then the appropri-
ate function key, as shown below.
NOTE
When the utility mode is first engaged from the SONG or PATTERN mode, the last
utility display selected will initially appear.
U t i l i t y F u n c t i o n s
220
System Parameters
The “System” display includes 5 parameters that affect the basic
operation of the QY70. Move the cursor to the parameter to be adjusted
and set as required by using the [-1] and [+1] keys.
CLICK MODE
Settings: Off, Record, Rec/Play, Always␣
Determines when the QY70 metronome will sound. Normally the
QY70 metronome sounds only during realtime recording — the
“Record” setting. With this parameter, however, you can turn the
metronome “Off” so that it never sounds, set it to “Rec/Play” so
that it sounds during recording and playback, or set it to “Always” so
that the metronome sounds at all times.
CLICK BEAT
Settings: 16, 8, 4, 2, 1
Determines on what beats the QY70 metronome will sound. The
normal setting is “4”, causing the metronome to sound on every
quarter-note beat. The metronome can also be set to sound on every
16th, 8th, 1/2, or whole-note beat.
221
14
U t i l i t y F u n c t i o n s
REC COUNT
Settings: OFF, 1 Meas … 8 Meas
This parameter sets the number of count-in measure provided
before realtime recording begins in the SONG and PATTERN modes.
The default setting is “1”.
MASTER TUNE
Settings: -102.4 … +000.0 … +102.3␣
Tunes the overall pitch of the QY70 sound. The Master Tune range is
from “-102.4” through “+000” to “+102.3”. Each increment corre-
sponds to aproximately 1 cent (a cent is 1/100th of a semitone). A
setting of “+000” produces normal pitch: A4 = 440 Hz.
SYSTEM EXCLUSIVE INTERVAL TIME
Settings: 0*100 … 9*100
This parameter sets the delay time between exclusive data blocks
between 0 and 900 milliseconds in 100-millisecond increments. This
type of delay is sometimes necessary to allow smooth playback of
song data which includes large system exclusive messages.
U t i l i t y F u n c t i o n s
222
MIDI Parameters
The parameters in the “MIDI” display all relate to MIDI control.
MIDI SYNC
Settings: Internal, External␣
When this parameter is set to “Internal” the QY70 is controlled by
its own internal clock. When set to “External” the QY70 is controlled
by a MIDI clock signal received from an external device such as a
sequencer or music computer (i.e., playback of the QY70 is synchro-
nized to that of an external sequencer or other device). Please note
that the QY70 will not run on its own when this parameter is set to
“External”. The QY70 can also control playback of an external MIDI
sequencer when this parameter is set to “Internal”.
MIDI CONTROL
Settings: Off, In, Out, In/Out
This parameter simply turns MIDI control of the QY70 (i.e., synchro-
nized playback) on or off. When set to “Off” the QY70 will not
respond to external MIDI control. The “In” setting (MIDI input only)
allows control of the QY70 from an external MIDI device, the “Out”
setting (MIDI output only) allows the QY70 to control an external
MIDI device, and the “In/Out” setting (MIDI input and output) allows
the QY70 to both be controlled by and control an external MIDI
device.
223
14
U t i l i t y F u n c t i o n s
ECHO BACK
Settings: Off, Thru, RecMontr
Determines whether MIDI data received via the MIDI IN terminal is
simultaneously re-transmited (“echoed back”) via the MIDI OUT
connector. When this parameter is set to “Off” no echo back
occurs. When set to “Thru” the received MIDI data is re-transmitted
without modification. When “RecMontr” (Record Monitor) is se-
lected, the received data is re-transmitted on the MIDI channel
corresponding to the currently selected record track, and the data is
affected by the MIDI FILTER settings described below.
LOCAL CONTROL
Settings: Off, On
Determines whether or not the QY70’s internal tone generator will
be controlled by its own micro-keyboard. When LOCAL CONTROL is
“On”, the micro-keyboard controls the internal tone generator.
When “Off” the micro-keyboard does not control the internal tone
generator and will produce no sound.
MIDI FILTER
Settings: Off, PB, CC, AT, Exc
The MIDI FILTER specifies a type of event which will not be re-
ceived via MIDI during sequence recording. The settings are as
follows:
Off All events are received.
PB Pitch bend events will not be received.
CC Control Change events will not be received.
AT Channel and polyphonic aftertouch events will not be
received.
Exc System exclusive data will not be received.
U t i l i t y F u n c t i o n s
224
PATT OUT CH
Settings: Off, 1~8, 9~16
This parameter specifies the MIDI channels on which QY70 pattern
playback data will be transmitted. When “Off” pattern playback data
is not transmitted. When set to “1~8” pattern playback data is
transmitted on MIDI channels 1 through 8, and when set to “9~16”
pattern playback data is transmitted on MIDI channels 9 through 16.
D1 ch 1 or 9
D2 ch 2 or 10
PC ch 3 or 11
BA ch 4 or 12
C1 ch 5 or 13
C2 ch 6 or 14
C3 ch 7 or 15
C4 ch 8 or 16
XG PARM OUT
Settings: Off, On
Determines whether the XG voice and effect parameters will be
transmitted whenever the corresponding parameter values are
changed or a new song or pattern is selected. When “Off” no XG
parameters are transmitted. The appropriate XG parameters are
transmitted to a connected XG tone generator when this parameter
is turned “On”.
225
14
U t i l i t y F u n c t i o n s
Bulk Dump
Although the QY70 has memory for 20 songs and 64 user styles,
you might want to save your song and pattern data to an external MIDI
data recorder, computer, or similar device to allow greater storage capacity
or simply to protect your data from accidental erasure or corruption.
Be sure to properly connect the QY70 to a MIDI data recorder(such
as the Yamaha MDF2 MIDI Data Filer) or a computer and set the HOST
SELECT switch to the appropriate position before executing the Bulk
Dump transmission/reception.
Also refer to the owner’s manual of the connected device to see
how to receive/transmit bulk data from/to the QY70.
To transmit (dump) song and/or pattern data to an external device,
first select the UTILITY Bulk Dump mode.
Connection via the MIDI IN/
OUT jack to the MDF2 (Host
Select=MIDI)
Connection via the TO
HOST jack to a computer
(Host Select=PC1/2 or Mac
according to the type of
computer. See page 17)
U t i l i t y F u n c t i o n s
226
Move the cursor to the upper parameter and use the [-1] and [+1]
keys to select “Song” if you want to save the data for one song or all
songs, “Style” if you want to save the data for one style or all styles, or
“All” if you want to save all songs, styles, and system setup data.
If you select “Song”, move the cursor to the song number param-
eter and select a song number (01 … 20), or “All” to save all songs.
If you select “Style”, move the cursor to the style number param-
eter and select a style number (U01 … U64), or “All” to save all styles.
Remember all 6 variation patterns(Intro, Main A/B, Fill AB/BA and Ending)
included in one style will be saved at one time.
When the parameters have been set as required, press [ENTER].
“Are you sure?” will appear on the display. Press [+1/YES] to go ahead
with the bulk dump operation, or [-1/NO] to cancel. “Completed!” will
appear when the transmission is finished.
Bulk Reception of Song & Pattern Data
If no other operation is currently in progress (recording, for example)
the QY70 will automatically receive bulk song and pattern data transmitted
from a compatible external device. If you are using the QY70’s MIDI
connectors rather than the TO HOST connector, make sure that the MIDI
OUT of the external device is connected to the MIDI IN of the QY70.
Select the QY70 SONG play mode when receiving one or all song
bulk data, and select the PATTERN play mode when receiving one or all
style bulk data. “All” data, including all songs, styles and system setup
data, can be received in either the SONG or PATTERN play mode. Remem-
ber that one or all song/style data currently in the QY70’s memory will be
overwritten when one or all song/style bulk data is received. All data in the
QY70’s memory will be overwritten when “All” data is received.
NOTE
See the QY Data Filer’s owners manual if you use the QY Data Filer for bulk dump
reception/transmission.
227
14
U t i l i t y F u n c t i o n s
Fingered Zone
The QY70’s advanced ABC system can be controlled from the QY70
micro-keyboard or an external keyboard. The Fingered Zone utility function
sets the range of notes in which chords played will be recognized by the
QY70 ABC system.
Use the “FINGERED” parameter to turn the QY70’s Fingered Chord
function for the ABC system “On” or “Off” as required. When it is turned
to “ON”, the ABC system can be controlled by playing a chord as it is on
an external keyboard or the micro keyboard. When turned to “OFF”, the
ABC system is controlled by specifying the chord root and type from the
micro keyboard rather than playing the chord as it is. The MIDI CHANNEL
and the “LOW”/“HIGH” parameters explained below will be ineffective
when turned to “OFF”.
The MIDI CHANNEL parameter specifies the MIDI channel via which
the chord data will be received from an external MIDI keyboard: set to
“All” for all channels, or specify a single MIDI channel from “01” to “16”.
The “LOW” and “HIGH” parameters above the graphic keyboard
display set the Fingered Chord function range. The maximum range is from
C-2 to G8 (the “HIGH” parameter cannot be set lower than the “LOW”
parameter). The specified range is indicated by the highlighted (inverse)
section on the graphic keyboard display. When the “FINGERED” param-
eter in this display and the “FNGR” parameter in the SONG or PATTERN
mode display are turned “On”, chords played within the specified Fingered
Chord function range will be recognized by the ABC system and the
U t i l i t y F u n c t i o n s
228
accompaniment chord will change accordingly during song, pattern play-
back or chord-track recording. Chords played within the specified range of
either the QY70 micro-keyboard or an external MIDI keyboard are recog-
nized. A chart of the chords recognized by the QY70 is provided on the List
Book.
If you play a note lower than the specified “LOW” note while
holding a chord, it will be recognized as a bass note for the on-bass chord.
NOTE
When the Fingered Chord function is “on”, notes played lower than the specified
“HIGH” note will not sound.
A p p e n d i x
15
229
A p p e n d i x
Specifications
Sequencer block
Data capacity approximately 32,000 notes
Note resolution 480 clocks per quarter note
Polyphony 64 notes
Tempo 25-300
Modes SONG mode (SONG, SONG VOICE, SONG EFFECT)
PATTERN mode (PATTERN, PATTERN VOICE, PATTERN
EFFECT)
Record modes Realtime replace, Realtime overdub, Step, Multi
Tracks Song: 16 sequencer tracks, pattern track(Pt),
chord track(Cd), tempo track(Tm)
Pattern: 8 pattern phrase tracks
Songs 20 songs + 3 demo songs
Patterns 768 preset patterns (128 preset styles x 6 sections)
384 user patterns (64 user styles x 6 sections)
Sections: Intro, Main A, Main B, Fill AB, Fill BA, Ending
Phrases 4,167 preset phrases
48 user phrases per user style
Chord types 26 types (including “non-ABC” type)
Chord templates 99 preset chord templates
1 user chord progression per song
Play effect Groove quantization, Drum table remapping
Tone generator block
Type AWM2 tone generator
Maximum Polyphony 32 notes
Multi-timbral capability 24 timbres (last note priority with element reserve, DVA)
Preset voices 519 normal voices, 20 drum voices
Effects 3 blocks (Reverb, Chorus, Variation)
Reverb: 11 types
Chorus: 11 types
Variation 43 types
A p p e n d i x
230
Controllers & display
Micro keyboard 25 keys (2 octaves)
Octave keys [OCT DOWN], [OCT UP]
Cursor keys up, down, left, right
Sequencer keys [
W
], [
A
], [
S
], [
U
], [
E
], [
R
]
[SONG], [PATT], [SHIFT], [EXIT], [MENU], [-1(NO)], [+1(YES)], [ENTER], Function
keys
Volume control
Contrast control
HOST SELECT switch
Display 128 x 64 dots graphic LCD
Connectors
LINE OUT/PHONES stereo mini jack x 1
MIDI IN x1, OUT x1
TO HOST
DC IN for PA-3B
Power supply
Optional PA-3B AC adapter
Six 1.5v AA size (SUM-3 or R6P) or equivalent alkaline
batteries
Dimensions
(W x D x H) 188 x 104 x 43 mm (7-3/8" x 4-1/8" x 1-11/16")
Weight
520g (1 lbs., 2 oz) without batteries
Included items
QY Data Filer 2HD floppy disk x 2
Audio cable miniature stereo phone plug to dual RCA pin plugs
Owner’s manual set QY70 owner’s manual, List book, QY Data Filer owner’s
manual
Creepers
* Specifications and descriptions in this owner’s manual are for information purposes
only. Yamaha Corp. reserves the right to change or modify products or specifications at
any time without prior notice. Since specifications, equipment or options may not be
the same in every locale, please check with your Yamaha dealer.
A p p e n d i x
15
231
Troubleshooting
If you experience problems such as “no sound,” “incorrect sound,” or “sequencer
does not operate,” please check the following points before deciding that the unit is
malfunctioning. In many cases, checking these points will help you solve the problem.
If this does not solve the problem, contact your nearest Yamaha dealer or the autho-
rized distributor for your country.
Problem
No sound
Possible causes
Is the volume sufficiently raised on the QY70
and/or external sound equipment?
Are the headphones or speakers properly
connected?
Is the Master Volume and/or each track
volumes raised sufficiently?
If the REVERB, CHORUS, VARI, and DRY
settings are all set to 0, the sound for that
track will not be produced.
Is the Fingered Chord function turned ON? If
you play a note within the Fingered Zone, no
sound will be produced.
Is the MUTE setting turned ON?
Is the MIDI IN jack or TO HOST jack properly
connected?
Is the HOST SELECT switch properly set?
Is MIDI local set to OFF?
Have unneeded effects been set?
Does the number of currently sounding notes
exceed the QY70’s maximum polyphony of
32?
Does the selected song/pattern contain data?
Is the MIDI Sync set to external?
Is Style Number 129 (End Pattern) selected in
the Song Mode’s display?
The length of a pattern (number of measures)
cannot be changed, if it includes recorded
user phrases.
Refer to page
The sound is distorted.
Notes are intermittently
broken (notes sputter or
stutter).
Playback does not start when
you press [
W
].
Can’t change the length of a
pattern (number of mea-
sures).
p.14
p.64
p.66
p.43, 227
p.62, 92, 141
p.15, 16
p.17
p.223
p.212
p.229
p.80, 137
p.222
p.35
p.148
A p p e n d i x
232
Is Style Number 129 (End Pattern) set in the
middle of the Pattern Track?
Are Play Effect settings being used?
Is the keyboard velocity set between R1 and
R4 (Random)?
Is the Fingered Chord turned off?
Are you pressing keys within the Fingered
Zone?
Is the click set to something other than “off”
in the Utility mode?
Does the beginning of the song contain data
which resets the tone generator?
If there is data in the Pattern track, the
Variation effect settings for the pattern will be
effective.
Press “SHIFT” and “F2” simultaneously to
check the current memory capacity. The
QY70’s memory capacity (approximately
32,000 notes) is for the total data of all songs
and phrases. This means that if there are
songs or phrases that contain large amounts
of data, the memory may be full even though
there are still unused songs or patterns.
Is the Utility mode’s MIDI Echo Back set to
RecMontr? Change the Echo Back setting to
Off or Thru.
When a song is played back,
it stops in the middle.
Rhythm or note timing are
played back differently than
when recorded.
The same amount of force is
used to play notes on the
keyboard but it results in
notes of different loudness.
Cannot use the Fingered
Chord function.
Can’t hear the click sound.
When the song starts, the
voice or effect settings that
you have made disappear.
The “Memory Full” message
appears yet there are still
unused songs.
The QY70 (tone generator) is
slaved to an external
sequencer but, there is no
sound when the performance
is played back from the
external sequencer.
Problem Possible causes
Refer to page
p.54
p.94
p.77, 145
p.43
p.227
p.220
p.192
p.217
p.26
p.223
A p p e n d i x
15
233
Error Messages
Monitor
No Data When a job is executed, this will appear if the selected
track or area contains no data, making the job invalid. Re-
select the area.
Illegal Input This will appear in response to inappropriate operation or
input. Check your input method.
Preset Phrase This will appear when you attempt to edit a Preset
Phrase. To edit a preset phrase, copy the phrase to a User
Phrase and edit the User Phrase.
Preset Pattern This will appear when you attempt to record to a Preset
Pattern. You cannot record to Preset Patterns.
Preset Chord This will appear when you attempt to change a Preset
Chord Template with a Job (transpose, etc.) operation.
Now Bulk Mode This will appear when you attempt to operate the QY70
while it is receiving bulk data.
System
Memory Full This will appear when internal memory is full and it is not
possible to record, edit, execute a job, receive MIDI, etc.
Delete unneeded songs, user patterns, or user phrases,
and try the operation once again.
Backup Batt. Low This will appear when the internal backup battery of the
QY70 has run down. Contact the nearest Yamaha dealer
or the authorized distributor for your country to have the
battery replaced.
Power Batt. Low This will appear when the batteries (Size AA x6) powering
the QY70 has run down. Replace the entire set of old
batteries with a new set of batteries as soon as possible.
Factory Set After the power is switched ON, a system diagnosis is
run on the QY70’s system. If the diagnosis finds the RAM
to be defective, this message will appear and the memory
will be reset to its original factory settings. Data for Song,
User Patterns, and User Phrases will all be eliminated.
A p p e n d i x
234
MIDI
MIDI Data Error This will appear when the received QY bulk data contains
an error.
Now Running This will appear when the QY70 is receiving bulk data.
Other MIDI signals cannot be received at this time.
MIDI Buffer Full This will appear when the MIDI reception buffer of the
QY70 has filled up, and processing was not possible. Try
decreasing the amount of data or increasing the interval
time and transmit the data once again.
XG Data Error This appears when the received XG parameter change
contains a data size error
XG Adrs Error This appears when the received XG data contains an
address error.
XG Size Error This appears when the received XG bulk data contains a
data size error.
Checksum Error This appears when the received XG data contains a
Checksum error.
Host is OffLine If the QY70 is connected to a computer, this appears
when the computer’s power is switched OFF. Switch the
computer’s power ON.
Messages other than error messages
Can’t Undo OK? (Yes/No)
If executing a job would fill up the internal memory so
that Undo will not be available, this message will appear.
If you are sure that you will not need to Undo this job,
press “YES”. To cancel without executing the job, press
“NO”.
Are You Sure? (Yes/No)
Before an operation is executed, this message will ask
you for confirmation. To execute the operation press
“YES”. To cancel the operation press “NO”.
Completed This will appear when the current process has been
completed.
Executing... This message will appear while the job is being executed.
Please wait.
Transmitting... When transmitting MIDI bulk data, this message will
appear.
Receiving... When receiving MIDI bulk data, this message will appear.
A p p e n d i x
15
235
Glossary
A
Aftertouch:
MIDI messages which are transmitted when
additional pressure is applied to the keyboard
after notes are played.
Attack time:
The time over which the volume rises from 0
when a note is played, until the maximum
volume is reached.
Auto Bass Chord (ABC):
A function which will automatically re-
harmonize the accompaniment patterns by
specifying chord progressions.
AWM 2 tone generator:
A method of generating sound developed by
Yamaha which is based on digitally recorded
waveforms. Since it generates the complex
waveform of actual acoustic instruments, it
provides extremely realistic sounds. Digital
filtering is also built-in, allowing precise
control over the tone. AWM2 is an acronym
for Advanced Wave Memory 2.
B
Beat:
When playing back or recording a song, one
“beat” (a rhythmic subdivision of a measure).
Bulk data:
A type of System Exclusive message which
contains a collection of data for the internal
settings of a device.
Bulk dump:
The process of transmitting bulk data in MIDI
System Messages to external MIDI devices.
C
Chord root:
An alphabetical letter which indicates the
root of a chord. The QY70 lets you indicate
12 different chord roots.
Chord template:
A collection of preset models for chord
progressions. The collection includes generic
chord progressions for Popular styles as well
as Blues and Tension styles.
Chord track (Cd):
A track that lets you record and play back
Chord Roots and Chord Types for the Auto
Bass Chord (ABC) function.
Chord type:
A symbolic or numerical indication of how a
chord is composed (Major, minor, 7th, etc.).
The QY70 allows you to select from 26
(including “non-ABC”) chord types.
Chorus:
A type of effect that adds richness and depth
to the sound, similar to what happens when
multiple sound sources are heard simulta-
neously.
Click:
A metronome that is sounded when playing
back or recording on a sequencer.
Clock:
A unit of timing resolution. On the QY70, one
clock is a length of 1/480th of a quarter note.
Control change:
A group of MIDI messages that can be used
to select voice banks and control the volume,
pan, etc. They are also output when a
controller (modulation wheel, foot controller,
etc.) is operated. Each controller has its own
control number.
A p p e n d i x
236
Cutoff frequency:
Filters work by allowing the portion of the
signal lower than a given frequency to pass,
and cutting the portion of the signal above
that frequency. This frequency is referred to
as the cutoff frequency. See the entry for
Low Pass Filter.
D
Decay time:
The time from when the maximum volume
of a note is reached until it falls to the sustain
level.
Delay:
An effect that delays an audio signal. The
QY70’s Variation effect allows a delay to be
applied.
Depth:
The amount or degree of a setting or effect.
Drum table remapping:
One of the play effect functions. This
function allows you to change specified
rhythm instruments in the drum play data to
other rhythm instruments when a song or
pattern is played back.
Dry sound:
The audio signal that is not processed by an
effect. Normally when using an effect, not all
of the audio signal is passed through the
effect. Rather, the degree of the effect is
adjusted by mixing the sound that passes
through the effect (the wet sound) with the
sound that bypasses the effect (the dry
sound). See also the entry for Wet sound.
E
Echo back:
The action or process in which data received
via the MIDI IN connector is re-transmitted
from the MIDI OUT connector.
Edit:
The action of modifying or editing data.
Effect:
A block that processes the sound to add
various effects. The QY70 provides two
system effects (reverb and chorus), and one
effect (variation) which can either be used as
a system effect or as an insertion effect.
Element:
A block within the AWM2 tone generator
that generates a sound. The voices of the
QY70 consist of 1 or 2 elements. Voices that
use 2 elements generally have a thicker
sound that cannot be achieved when using 1
element. With 2 elements different voices
such as piano and strings sounds can be
mixed into a single voice.
Envelope generator (EG):
A block that modifies the level of the tone
generator from the moment that a note is
played until the sound decays to silence.
Event:
A single piece (such as Note On/Off or
Program Change messages) of the data
which makes up a sequence.
Exclusive:
See the entry for System Exclusive Mes-
sage.
Expression:
A MIDI control change message used to
control the volume of a part (track).
F
Filter:
A block which modifies the tone by cutting
the output of a specific frequency portion of
the sound. The QY70 has low pass filters
allowing the tone to be made more mellow
by cutting the overtones above a specified
frequency, or brighter by allowing them to
pass. See also the entry for Low pass filter.
A p p e n d i x
15
237
Fingered chord:
A function that automatically detects chords
based on the combination of notes that are
played on the keyboard, and converts the
playback of patterns to the chords that are
detected.
G
Gate Time:
The length of time that a note actually
sounds. Longer gate times produce slurred
notes, shorter gate times produce staccato.
GM:
An acronym for General MIDI. A specification
that defines the arrangement of voices in a
tone generator and its MIDI functionality,
ensuring that data can be played back with
substantially the same sounds on any GM-
compatible tone generator.
Groove quantization:
A Play Effect function that can be applied to
Song or Pattern data during playback. This
effect allows the song’s feel or “groove”
(putting the rhythm in front of or behind the
beat) to be altered without changing the
state of the original data.
Groove templates:
A collection of groove templates that can be
used in the Groove Quantization function.
H
Hexadecimal number:
A system of numbering based on 16, in
which the digits increment in units of n-th
powers of 16. The alphabetical characters A-
F are used to express the numbers 10-15.
This system of numbering is used for MIDI
data.
I
IBM-PC/AT Series:
A type of personal computer manufactured
and sold by the International Business
Machine Corporation. Compatible computers
are manufactured and sold by many
companies
Insertion (effect):
An effect which can be applied to one
specific part (track). With this effect, you can
apply effects more “aggressively” to your
song. (e.g. rotary speaker effects to organ
sounds, or “wah” effects to guitar sounds.)
Interval time:
A delay time that is inserted at regular
intervals of one kilobyte when transmitting
system exclusive data that was recorded in a
sequence track to tone generators (or
external MIDI tone generators).
L
LFO:
An acronym for Low Frequency Oscillator, a
block that produces a signal at a low
frequency which synthesizers use for the
creation of sound. The signal from the LFO
can be used to modulate pitch, volume or
tone to produce effects such as vibrato,
tremolo and wah.
Location:
The place within a song or pattern at which
notes will be input or playback will be
started, indicated as measure, beat, and
clock.
Low Pass Filter:
A type of filter which cuts high frequencies
above a specified point. The sound can be
brightened by raising the cutoff frequency of
the filter, or darkened by lowering it.
LSB:
An acronym for Least Significant Byte,
referring to the lower byte of data when
MIDI control change data is divided into two
bytes for transmission.
A p p e n d i x
238
M
Maximum Polyphony:
The maximum number of notes that can be
played at once. The QY70 can produce 32
simultaneous notes (counted in 1-element
units). If MIDI messages are received
requesting more notes than the maximum
polyphony allows, currently sounding notes
will be turned off, and the later-received
notes will be played.
Measure:
A unit of musical duration consisting of
several beats.
MIDI:
An acronym for Musical Instruments Digital
Interface, a standard for transferring data
between musical instruments. Most
electronic musical instruments today
implement the MIDI specification and
provide MIDI connectors. Such instruments
can be easily connected together to create
remote performance or automatic perfor-
mance systems.
MIDI Data Filer:
A MIDI device that receives bulk data for the
internal settings of a MIDI device in the form
of System Exclusive messages, and stores
them to disk. An example is the Yamaha
MDF2 MIDI data filer.
Mixer:
On the QY70, the display page in which you
can make settings such as, pan, volume, etc.
for the voice of each song or pattern track,
when playing back.
Modulation:
A function that can be used to change the
volume, tone, or pitch cyclically while you
perform. On the QY70, you can apply
modulation by holding the [OCT UP] key
while playing a note on the micro keyboard.
MSB:
An acronym for Most Significant Byte,
referring to the upper byte of data when
MIDI control change data is divided into two
bytes for transmission.
Multi-timbral tone generator:
A tone generator that can simultaneously
produce more than one voice.
Mute:
A function that temporarily silences the
specified track or reduces its volume.
N
NRPN:
An acronym for Non Registered Parameter
Number. These are a type of MIDI control
change message, and are used to edit
sounds via MIDI, allowing you to edit filter or
EG settings, or adjust the pitch or level for
each instrument of a drum voice.
O
On-bass:
A function that lets you specify a root note
for the bass independently of the chord, so
that the playback of a bass phrase whose
Phrase Type is Bass will be fixed on that root
note.
Overdub:
A method of real-time recording in which
new material is recorded without erasing
previously recorded tracks.
P
Pan:
The parameter that sets the stereo location
of a sound when it is played back in stereo.
(“Pan” or “panpot” are abbreviations of
“panoramic potentiometer”.)
Parameter:
A setting or data item which you can modify
in the various mode and sub-mode displays.
A p p e n d i x
15
239
Patch:
An assignment of phrases for each track to
create patterns.
Pattern:
An auto accompaniment pattern consisting
of drums, bass and chord backing.
Pattern track (Pt):
The track which records and plays back
pattern data.
PC-9801/9821 Series:
A type of personal computer manufactured
and sold by the NEC Corporation widely in
Japan. Compatible computers are manufac-
tured and sold by the EPSON Company.
Phrase:
The smallest unit from which the accompani-
ment pattern is created. A phrase, such as
drum phrase, bass phrase, etc., can be
assigned to one of the 8 tracks of the
pattern.
Phrase category:
A classification of phrases that are catego-
rized by instruments and performance styles.
Pitch bend:
A type of MIDI message that smoothly
changes the pitch.
Pitch bend wheel:
A controller that smoothly changes the pitch.
On the QY70, pitch bend can be applied by
holding the [OCT DOWN] key while playing a
note on the micro keyboard.
Portamento:
An effect that smoothly changes the pitch
from one note to another note. Higher
settings of Portamento Time will produce a
slower change, and there will be no effect
with a setting of 0.
Preset:
A type of memory that is built into a device.
The QY70 has preset memories for voices,
phrases, and patterns, etc.
Program change:
An event or MIDI message that selects a
voice.
Program number:
On the QY70, a number specifying one of
the GM-defined voices.
Q
Quantize:
A function which “Tightens up” the inexact
timing of notes or other events that were
entered in real-time.
QY Data Filer:
A computer software application that allows
for the exchange of QY70 data between the
computer and the QY70. Data from the QY70
can be saved in the computer and QY data
stored in the computer can be transmitted to
the QY70. Commercially available SMF song
data or XG song data can also be transmitted
from the computer to the QY70.
R
Realtime recording:
A method of recording in which your
performance is recorded just as you play,
similar to a conventional multi-track recorder.
Since the performance is recorded as you
play, the musical expression and nuances of
your performance will be accurately
recorded.
Redo:
Carries out the operation that was previously
canceled with Undo.
Release time:
The time over which the volume falls from
the sustain level (beginning at the moment a
note is released) until it reaches silence.
A p p e n d i x
240
Replace:
A method of real-time recording in which
previously recorded data is erased (replaced)
as new material is recorded.
Resonance:
A parameter that boosts the level of the
signal in the area of the cutoff frequency. By
emphasizing the overtones in this area, this
can produce a distinctive “peaky” tone,
making the sound brighter and harder.
Return level:
See the entry for Send level.
Reverb:
An effect that simulates the acoustical
reverberance of a room or space. The sound
that reaches our ear usually includes not only
the direct sound, but also that was reflected
off the walls or ceiling. Reverb creates these
indirect reflections artificially.
RPN:
An acronym for Registered Parameter
Number. These are a type of MIDI control
change message that are used to set Part
settings such as Pitch Bend Sensitivity or
Tuning, etc.
S
Section:
A term referring to each of the six types of
patterns that comprise a style. Patterns are
selected by specifying the style and the
section.
Send level:
The amount of signal that is sent to a
specified bus line for processing by an effect.
The amount of signal that is returned from
the effect is the “return level”.
Sequencer:
A block (or device) that records, edits,
modifies, and plays back a musical perfor-
mance in the form of MIDI messages.
Sequencer tracks:
Tracks which record and playback normal
MIDI sequence data. The QY70 has 16
sequencer tracks.
SMF:
See the entry for Standard MIDI File.
Solo:
This function mutes the playback of all tracks
except that of the selected track as long as
the track is soloed.
Song:
A musical composition created by recording
performance data on each track.
Standard MIDI File (SMF):
SMF is an acronym for Standard MIDI File; a
standard format that was created to allow
easy exchange of song data between
different sequencers. Most of today’s
software and hardware manufacturers
provide sequencers that can create and play
back Standard MIDI files.
Step recording:
The method of recording in which music is
input by entering notes one by one,
specifying the note length, velocity, and pitch
etc. of each note.
Style:
A collective name for pattern catagories (hip
hop, U.K. techno, etc. musical genres).
Styles are divided into six sections (intro, fill-
in, ending, etc.).
Sustain level:
The volume level of the note from the time
after the maximum level of the note is
reached, until the note played on the
keyboard is released.
Synchronization:
The function or process of matching the
playback or recording tempo of a device with
a separated, external device such as another
sequencer or a rhythm machine.
A p p e n d i x
15
241
Sync:
See Synchronization
System (effect):
An effect which can be applied to all parts
(tracks) by adjusting the Send Levels and
Return Level. System effects allow reverb or
chorus to be conveniently applied to the
overall music. The QY70 provides Reverb
and Chorus as system effects. The Variation
effect can also be used as a system effect.
System Exclusive Message:
A type of MIDI message used to exchange
data unique to a specific model or type of
device.
T
Tempo track (Tm):
The track in which data that determines the
playback tempo of the song is recorded.
Track:
A location where musical performance data
is recorded in the sequencer. You can record
piano on track 1, bass on track 2, etc.
Transpose:
Shifts the pitch of recorded data in semitone
steps.
Tremolo:
An effect produced by cyclically modulating
the volume.
Tuning:
The process of matching the pitch of two or
more instruments when playing in an
ensemble. Normally, A3 is tuned to 440Hz.
U
Undo:
This command cancels the previously
performed operation and returns the data to
the condition of that before the operation
was executed. On the QY70, this command
can be performed against JOB, EDIT, and
RECORDING operations. See the entry for
Redo.
Utility:
On the QY70, the display in which MIDI
settings and system settings can be made.
V
Variation effect:
One of the QY70’s effects which can
function either as an insertion effect or as a
system effect, and provides a wide variety of
effect programs such as delay, rotary
speaker, auto pan, amp simulation and auto
wah in addition to reverb and chorus.
Velocity:
A numerical value indicating the speed
(force) with which a note was pressed.
Vibrato:
A performance effect produced by cyclically
changing the pitch.
Voice:
A sound that is built into the tone generator
that can be selected and played.
W
Wet sound:
The audio signal that is processed by an
effect. Normally when using an effect, not all
of the signal is passed through the effect.
Rather, the degree of the effect is adjusted
by mixing the sound that passes through the
effect (the wet sound) with the sound that
bypasses the effect (the dry sound). See also
the entry for Dry sound.
X
XG:
A tone generator format developed by
Yamaha which expands the GM specification
to provide the richer expressiveness and
upward data compatibility that is demanded
by today’s more sophisticated computer
peripheral environment.
A p p e n d i x
242
Index
A
AC Adaptor.............................. 1, 11, 12, 230
Aftertouch ....................................... 201, 235
Alkaline Batteries ............................ 1, 9, 230
Attack Time ....................................... 71, 235
Auto Bass Chord (ABC) ........................... 235
B
BA ...................................................... 140
Back Delete ............................................... 86
Backup Battery .................................... 2, 233
Bdl ........................................................ 86
Beat ................................................ 86, 235
Bulk Dump ...................................... 225, 235
C
C1, C2, C3, C4 ........................................ 140
CAT ...................................................... 201
CC (Control Change) ....................... 200, 235
Cd .................................................. 48, 57
Channel After Touch ................................ 201
Chord ........................................................ 39
Chord Separate ..................... 117, 173
Chord Sort ............................. 116, 172
Current Chord ............................... 211
Root ........................................ 40, 235
Source Chord ........................ 144, 211
Template ................. 43, 119, 229, 235
Template List ...................................
Track.................................. 48, 57, 235
Type ............................. 40, 41, 235,
Chorus............... 66, 152, 212, 214, 216, 235
CHORUS (Chorus Send) ........................... 67
Clear Pattern ........................................... 190
Clear Song ............................................... 135
Clear Track ........................................ 131,188
Click Beat ................................................ 220
Click Mode .............................................. 220
Clock ................................................ 86, 235
Connections .................................. 14, 15, 16
Connection Display ................................. 212
Contrast .................................................... 23
Control Change ............................... 200, 235
Copy Event...................................... 118, 174
Copy Pattern ........................................... 189
Copy Phrase ............................................ 183
Copy Song ............................................... 134
Copy Track ........................................ 129,186
Create Continuous .......................... 123, 179
Create Measure ...................................... 127
Crescendo ....................................... 111, 167
Current Chord ......................................... 211
Cursor ....................................................... 25
CUT .................................................. 70, 74
D
D1, D2 ..................................................... 140
DC In ........................................................ 12
Decay .......................................... 71, 74, 236
del ................................................ 86, 197
Delete ....................................... 86, 128, 197
Delete Measure ...................................... 128
Demo Song ............................................... 31
Display (LCD) ............................................ 23
Drum Table Number ........................... 100,
Drum Table .............................................. 100
Drum Table Remapping..................... 98, 236
Drum Voice .................................... 26, 63,
Drum Voice Edit ........................................ 72
DRY/WET .......................... 67, 215, 236, 241
Ds1, Ds2 ............................................. 63, 72
Ds3 ...................................................... 154
E
Echo Back ....................................... 223, 236
Edit .............................................. 192, 236
Effect .............................................. 212, 236
Chorus .... 66, 152, 212, 214, 216, 235
Data Assign Table ............................
Effect Send ............... 66, 73, 152, 215
Insertion Effect ............. 212, 215, 237
Parameter List .................................
Reverb .... 66, 152, 212, 214, 216, 240
System Effect ....... 212, 214, 215, 241
Type List ...........................................
Variation Effect
........ 66, 152, 212, 214, 215, 217, 241
EG ................................................ 71, 236
Erase Event ..................................... 120, 176
Error Message ........................................ 233
ers .................................................. 56, 60
Exc ...................................................... 203
: List Book
A p p e n d i x
15
243
Exclusive ......................................... 203, 241
Expand Backing ....................................... 132
Expression .............................................. 236
Extract Event ................................... 121, 177
F
Filter Cutoff Frequency ............... 70, 74, 236
Filter Resonance ......................... 70, 74, 240
FINGERED .............................................. 227
Fingered Chord ...... 43, 93, 211, 227, 237,
Fingered Zone ......................................... 227
FNGR .......................... 39, 43, 143, 211, 227
Function Keys ........................................... 26
FX THRU ............................................. 97, 99
G
GATE ........................................................ 84
Gate Time .. 84, 106, 109, 162, 165, 196, 237
Get Phrase .............................................. 184
Groove Quantization ................. 96, 155, 237
Groove Template ............................... 97, 237
Groove Template List .................................
H
Headphones .............................................. 13
HI KEY ..................................................... 211
HI LIMIT .................................................. 211
HOST SELECT .............................. 13, 15, 17
I
Insert ...................................................... 197
INSERTION ............................................. 212
Insertion Effect ......................... 73, 215, 237
J
JUMP ........................................................ 90
K
Keyboard Velocity .......................... 77, 84, 93
L
LINE OUT/PHONES .................... 13, 14, 230
LOCAL ON/OFF ...................................... 223
LO LIMIT ................................................. 211
LVL ........................................................ 73
M
M/S ............................................ 62, 97, 99
Master Tune ............................................ 221
Master Volume .................................... 30, 64
Maximum Polyphony ...................... 229, 238
Measure ...................................... 86, 90, 238
Create Measure ............................ 127
Delete Measure ............................ 128
Micro Keyboard ......................................... 28
MIDI .............................................. 222, 238
MIDI Channel ................................ 227
MIDI Control ................................. 222
MIDI Data Format ............................
MIDI Driver ..................................... 19
MIDI Filter ..................................... 223
MIDI Implementation .......................
MIDI IN/OUT ....................... 13, 15, 16
MIDI Sync ..................................... 222
Mix Track ......................................... 130, 187
Mixer Display .................................... 61, 238
Modify Gate Time ............................ 109, 165
Modify Velocity ............................... 107, 163
Modulation .............................................. 238
mst ........................................................ 64
Multi ........................................................ 80
Mute ...................... 62, 92, 97, 99, 141, 238
N
Normalize ................................................ 133
Normal Voice ........................................ 63,
Note .............................................. 196, 198
Note Display.............................................. 85
Note Pointer .............................................. 85
NRPN .............................................. 202, 238
O
OCT ........................................................ 29
Octave....................................................... 29
On-Bass ............................................ 58, 238
OVER ................................................ 78, 146
Overdub .................................... 78, 146, 238
A p p e n d i x
244
P
Pan .......................................... 64, 73, 238
Pat ........................................................ 64
PAT ...................................................... 201
Pattern ........................................ 7, 137, 239
Clear Pattern ................................. 190
Copy Pattern ................................. 189
Effect Mode .................................. 212
Job ................................................ 157
Mode ............................................ 137
Output Channel ............................. 224
Play ................................................. 33
Play Effect ..................................... 155
Phrase Track .......................... 140, 145
Track (Pt) ........................... 44, 54, 239
Track fader ...................................... 61
Voice Mode ................................... 151
PATT OUT CH.......................................... 224
PB ........................................ 69, 199, 239
PC (Percussion) ....................................... 140
PC (Program Change)...................... 199, 239
Phrase ............................................. 137, 239
Beat .............................................. 137
Category ............................... 137, 239
Copy .............................................. 183
Edit ................................................ 192
Edit Insert ..................................... 197
Get ................................................ 184
Name ............................................ 141
Number ......................................... 137
Put ................................................ 185
Recording .............................. 144, 150
Table.............................................. 210
Track...................................... 140, 145
Type ...................................... 146, 210
User Phrase .................................. 145
Voice ..................................... 147, 210
Pitch ........................................................ 73
Pitch Bend ................................. 69, 199, 239
Pitch Coarse .............................................. 73
Play Effect ......................................... 94, 155
Play Effect Thru................................... 97, 99
Play Fx............................................... 94, 155
Polyphonic Aftertouch ............................. 201
Power .............................................. 9, 11, 23
Preset Pattern ................................... 33, 229
Preset Phrase ............................. 137, 229,
Preset Style .......................................... 35,
Program Change ............................. 199, 239
Program Number .............................. 63, 239
Pt .................................................. 44, 54
Put Phrase ............................................... 185
Q
Quantize .................................. 104, 160, 239
Gate Time .............................. 106, 162
Quantize Value ...................... 104, 160
Strength ................................ 105, 161
Swing Rate ........................... 105, 161
QY Data Filer ........................................... 239
R
Realtime Recording ............. 44, 76, 144, 239
Chord Track ..................................... 48
Overdub .......................... 78, 146, 238
Pattern Track ................................... 44
Phrase ........................................... 144
Replace ............................. 45, 78, 240
Sequencer Track ............................. 76
Tempo Track .................................... 50
Rec Count ............................................... 221
Record Mode ........................ 45, 77, 82, 146
Record Ready ...... 28, 45, 48, 51, 77, 82, 146
Redo ................................ 26, 103, 159, 239
Release Time ..................................... 71, 239
Repeat Playback ........................................ 90
REPL .................................................. 45, 78
Replace ....................................... 45, 78, 240
RES .................................................. 70, 74
Rest ........................................................ 86
REV ........................................................ 73
Reverb............... 66, 152, 212, 214, 216, 240
REVERB (Reverb Send) ............................. 67
RPN .............................................. 202, 240
rst ........................................................ 86
S
Section ................................ 36, 55, 139, 240
Sequencer Key .......................................... 28
Sequencer Track ........................ 75, 229, 240
Shift Clock ....................................... 114, 170
Slur ........................................................ 84
Solo ...................... 62, 92, 97, 99, 141, 240
Song ................................................ 88, 240
Clear Song .................................... 135
Copy Song .................................... 134
Edit ................................................ 192
Edit Insert ..................................... 197
A p p e n d i x
15
245
Effect Mode .................................. 212
Job ................................................ 101
Mode .............................................. 88
Name ............................................ 136
Number ........................................... 88
Playback .......................................... 89
Play Effect ....................................... 94
Recording .................................. 44, 75
Song Name ................................... 136
Voice Mode ..................................... 61
Sound on/off ............................................. 60
SOURCE CHORD ............................ 144, 211
Specifications .......................................... 229
Swing Rate ...................................... 105, 161
Staccato .................................................... 84
STEP .................................... 52, 82, 84, 150
Step Recording ................... 51, 81, 150, 240
Chord Track ..................................... 57
Pattern Track ................................... 54
Phrase ........................................... 150
Sequencer Track ............................. 81
Style .................................................. 7, 240
Name ...................................... 55, 191
Number ............................. 35, 55, 139
Syncopation .............................................. 59
System Parameters ................................ 220
SYSTEM .................................................. 212
System Effect ................. 212, 214, 215, 241
System Exclusive Interval Time ...... 221, 237
T
Tempo ........................................... 46, 50, 91
Tempo Change .................................. 50, 206
Tempo Track ...................................... 50, 241
Thin Out .......................................... 125, 181
Thru ...................................................... 223
Tie ........................................................ 86
Time Stretch .................................... 126, 182
TIMING ............................................... 96, 98
Tm ................................................ 50, 241
TO CHO .................................................. 215
TO HOST ................................................... 13
TO REV ................................................... 215
Tone Generator ................................. 5 ,8, 16
Track ............................................ 6, 91, 241
Chord Track ....................... 48, 57, 235
Clear Track ............................ 131, 188
Copy Track ............................ 129, 186
Mix Track ............................... 130, 187
Pattern Phrase Track ............. 140, 145
Pattern Track (Pt) ............... 44, 54, 239
Sequencer Track ............. 75, 229, 240
Tempo Track ............................ 50, 241
Transpose .......................... 93, 113, 169, 241
TRNS ........................................................ 93
TYPE .............................................. 146, 210
U
Undo ................................ 26, 103, 159, 241
Used Memory ........................................... 26
User Pattern ............................................ 139
User Phrase ............................................ 145
USR ........................................................ 43
Utility .............................................. 218, 241
V
VAR ........................................................ 73
VARI. (Variation Send)................................ 67
Variation Effect
........ 66, 152, 212, 214, 215, 217, 241
View Filter ............................................... 209
VELO ............................................ 77, 84, 93
VELOC ...................................................... 98
Velocity ............ 77, 84, 93, 98, 107, 163, 241
Velocity Meter ........................................... 92
Voice ........................................ 61, 151, 241
Category ......................................... 63
Drum Voice .......................... 26, 63,
Edit .......................................... 68, 154
Name ...............................................
Normal Voice ....................................
Variation (Voice).......................... 63,
Volume ................................................ 30, 64
X
XG Exc Drum .......................................... 206
XG Exc Effect .......................................... 205
XG Exc Multi ........................................... 206
XG Exc System ....................................... 205
XG PARM OUT ........................................ 224
XG NRPN ................................................ 204
XG RPN ................................................... 204
XG View .................................................. 208
Z
ZONE ...................................................... 227
Buttons & Display Symbols
[
U
] ........................................................ 28
[
E
] ........................................................ 28
[
R
] ........................................................ 28
[
S
] ........................................................ 28
[
A
] ........................................................ 28
[
W
] ........................................................ 28
[-1(NO)]/[+1(YES)] ...................................... 25
[ENTER] ..................................................... 27
[EXIT] ........................................................ 25
[F1] - [F4] (Function Keys) ......................... 26
[MENU] ..................................................... 26
[OCT DOWN]/[OCT UP] ............................ 29
[PATT] ........................................................ 24
[SHIFT] ...................................................... 24
[SONG] ...................................................... 23
Cursor keys ............................................... 25
Micro Keyboard ......................................... 28
........................................................ 90
...................................................... 141
...................................................... 209
A p p e n d i x
246
FCC INFORMATION (U.S.A.)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions contained in this
manual, meets FCC requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC, to use the product.
2. IMPORTANT: When connecting this product to accessories and/or another product
use only high quality shielded cables. Cable/s supplied with this product MUST be
used. Follow all installation instructions. Failure to follow instructions could void your
FCC authorization to use this product in the USA.
3. NOTE: This product has been tested and found to comply with the requirements
listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with
these requirements provides a reasonable level of assurance that your use of this
product in a residential environment will not result in harmful interference with other
electronic devices. This equipment generates/uses radio frequencies and, if not
installed and used according to the instructions found in the users manual, may
cause interference harmful to the operation of other electronic devices. Compliance
with FCC regulations does not guarantee that interference will not occur in all
installations. If this product is found to be the source of interference, which can be
determined by turning the unit “OFF” and “ON”, please try to eliminate the problem
by using one of the following measures:
Relocate either this product or the device that is being affected by the interference.
Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or
install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the antenna. If the antenna
lead-in is 300 ohm ribbon lead, change the lead-in to co-axial type cable.
If these corrective measures do not produce satisfactory results, please contact the
local retailer authorized to distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Corporation of America, Electronic
Service Division, 6600 Orangethorpe Ave, Buena Park, CA90620
The above statements apply ONLY to those products distributed by Yamaha
Corporation of America or its subsidiaries.
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.
ADVARSEL!
Lithiumbatteri—Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med
batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandoren.
VARNING
Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller en ekvivalent typ
som rekommenderas av apparattillverkaren. Kassera använt batteri enlight fabrikantens
instruktion.
VAROITUS
Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan
laitevalmistajan suosittelemaan tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden
mukaisesti.
NEDERLAND / NETHERLAND
Dit apparaat bevat een lithium batterij voor geheugen back-up.
This apparatus contains a lithium battery for memory back-up.
Raadpleeg uw leverancier over de verwijdering van de batterij op het moment dat u
het apparaat ann het einde van de levensduur afdankt of de volgende Yamaha
Service Afdeiing:
Yamaha Music Nederland Service Afdeiing
Kanaalweg 18-G, 3526 KL UTRECHT
Tel. 030-2828425
For the removal of the battery at the moment of the disposal at the end of the service
life please consult your retailer or Yamaha Service Center as follows:
Yamaha Music Nederland Service Center
Address : Kanaalweg 18-G, 3526 KL UTRECHT
Tel : 030-2828425
Gooi de batterij niet weg, maar lever hem in als KCA.
Do not throw away the battery. Instead, hand it in as small chemical waste.
For details of products, please contact your nearest Yamaha or the
authorized distributor listed below.
Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha
ou au distributeur le plus proche de vous figurant dans la liste suivante.
Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten Nie-
derlassung und bei Yamaha Vertragshändlern in den jeweiligen
Bestimmungsländern erhältlich.
Para detalles sobre productos, contacte su tienda Yamaha más cercana
o el distribuidor autorizado que se lista debajo.
NORTH AMERICA
CANADA
Yamaha Canada Music Ltd.
135 Milner Avenue, Scarborough, Ontario,
M1S 3R1, Canada
Tel: 416-298-1311
U.S.A.
Yamaha Corporation of America
6600 Orangethorpe Ave., Buena Park, Calif. 90620,
U.S.A.
Tel: 714-522-9011
MIDDLE & SOUTH AMERICA
MEXICO
Yamaha De Mexico S.A. De C.V.,
Departamento de ventas
Javier Rojo Gomez No.1149, Col. Gpe Del
Moral, Deleg. Iztapalapa, 09300 Mexico, D.F.
Tel: 686-00-33
BRASIL
Yamaha Musical Do Brasil LTDA.
Ave. Reboucas 2636, São Paulo, Brasil
Tel: 011-853-1377
PANAMA
Yamaha De Panama S.A.
Edificio Interseco, Calle Elvira Mendez no.10,
Piso 3, Oficina #105, Ciudad de Panama, Panama
Tel: 507-69-5311
OTHER LATIN AMERICAN COUNTRIES
AND CARIBBEAN COUNTRIES
Yamaha Music Latin America Corp.
6101 Blue Lagoon Drive, Miami, Florida 33126,
U.S.A.
Tel: 305-261-4111
EUROPE
THE UNITED KINGDOM
Yamaha-Kemble Music (U.K.) Ltd.
Sherbourne Drive, Tilbrook, Milton Keynes,
MK7 8BL, England
Tel: 01908-366700
IRELAND
Danfay Ltd.
61D, Sallynoggin Road, Dun Laoghaire, Co. Dublin
Tel: 01-2859177
GERMANY/SWITZERLAND
Yamaha Europa GmbH.
Siemensstraße 22-34, 25462 Rellingen,
F.R. of Germany
Tel: 04101-3030
AUSTRIA
Yamaha Music Austria
Schleiergasse 20, A-1100 Wien Austria
Tel: 0222-60203900
THE NETHERLANDS
Yamaha Music Nederland
Kanaalweg 18G, 3526KL, Utrecht, The Netherlands
Tel: 030-2828411
BELGIUM
Yamaha Music Belgium
Keiberg Imperiastraat 8, 1930 Zaventem, Belgium
Tel: 02-7258220
FRANCE
Yamaha Musique France,
Division Professionnelle
BP 70-77312 Marne-la-Valée Cedex 2, France
Tel: 01-64-61-4000
ITALY
Yamaha Musica Italia S.P.A.,
Combo Division
Viale Italia 88, 20020 Lainate (Milano), Italy
Tel: 02-935-771
SPAIN
Yamaha-Hazen Electronica Musical, S.A.
Jorge Juan 30, 28001, Madrid, Spain
Tel: 91-577-7270
PORTUGAL
Valentim de Carvalho CI SA
Estrada de Porto Salvo, Paço de Arcos 2780 Oeiras,
Portugal
Tel: 01-443-3398/4030/1823
GREECE
Philippe Nakas S.A.
Navarinou Street 13, P.Code 10680, Athens, Greece
Tel: 01-364-7111
SWEDEN
Yamaha Scandinavia AB
J. A. Wettergrens Gata 1
Box 30053
S-400 43 Göteborg, Sweden
Tel: 031 89 34 00
DENMARK
YS Copenhagen Liaison Office
Generatorvej 8B
DK-2730 Herlev, Denmark
Tel: 44 92 49 00
FINLAND
Warner Music Finland OY/Fazer Music
Aleksanterinkatu 11, P.O. Box 260
SF-00101 Helsinki, Finland
Tel: 0435 011
NORWAY
Narud Yamaha AS
Grini Næringspark 17
N-1345 Østerås, Norway
Tel: 67 14 47 90
ICELAND
Skifan HF
Skeifan 17 P.O. Box 8120
IS-128 Reykjavik, Iceland
Tel: 525 5000
OTHER EUROPEAN COUNTRIES
Yamaha Europa GmbH.
Siemensstraße 22-34, 25462 Rellingen, F.R. of
Germany
Tel: 04101-3030
AFRICA
Yamaha Corporation,
International Marketing Division
Nakazawa-cho 10-1, Hamamatsu, Japan 430
Tel: 053-460-2312
MIDDLE EAST
TURKEY/CYPRUS
Yamaha Europa GmbH.
Siemensstraße 22-34, 25462 Rellingen,
F.R. of Germany
Tel: 04101-3030
OTHER COUNTRIES
Yamaha Corporation,
International Marketing Division
Nakazawa-cho 10-1, Hamamatsu, Japan 430
Tel: 053-460-2312
ASIA
HONG KONG
Tom Lee Music Co., Ltd.
11/F., Silvercord Tower 1, 30 Canton Road,
Tsimshatsui, Kowloon, Hong Kong
Tel: 730-1098
INDONESIA
PT. Yamaha Music Indonesia (Distributor)
PT. Nusantik
Gedung Yamaha Music Center, Jalan Jend. Gatot
Subroto Kav. 4, Jakarta 12930, Indonesia
Tel: 21-520-2577
KOREA
Cosmos Corporation
#131-31, Neung-Dong, Sungdong-Ku, Seoul
Korea
Tel: 02-466-0021~5
MALAYSIA
Yamaha Music Malaysia, Sdn., Bhd.
16-28, Jalan SS 2/72, Petaling Jaya, Selangor,
Malaysia
Tel: 3-717-8977
PHILIPPINES
Yupangco Music Corporation
339 Gil J. Puyat Avenue, P.O. Box 885 MCPO,
Makati, Metro Manila, Philippines
Tel: 819-7551
SINGAPORE
Yamaha Music Asia Pte., Ltd.
Blk 17A Toa Payoh #01-190 Lorong 7
Singapore 1231
Tel: 354-0133
TAIWAN
Kung Hsue She Trading Co., Ltd.
No. 322, Section 1, FuHsing S. Road,
Taipei 106, Taiwan. R.O.C.
Tel: 02-709-1266
THAILAND
Siam Music Yamaha Co., Ltd.
865 Phornprapha Building, Rama I Road,
Patumwan, Bangkok 10330, Thailand
Tel: 2-215-3443
THE PEOPLE’S REPUBLIC OF CHINA
AND OTHER ASIAN COUNTRIES
Yamaha Corporation,
International Marketing Division
Nakazawa-cho 10-1, Hamamatsu, Japan 430
Tel: 053-460-2317
OCEANIA
AUSTRALIA
Yamaha Music Australia Pty. Ltd.
17-33 Market Street, South Melbourne, Vic. 3205,
Australia
Tel: 3-699-2388
NEW ZEALAND
Music Houses of N.Z. Ltd.
146/148 Captain Springs Road, Te Papapa,
Auckland, New Zealand
Tel: 9-634-0099
COUNTRIES AND TRUST
TERRITORIES IN PACIFIC OCEAN
Yamaha Corporation,
International Marketing Division
Nakazawa-cho 10-1, Hamamatsu, Japan 430
Tel: 053-460-2317
HEAD OFFICE Yamaha Corporation, Electronic Musical Instrument Division
Nakazawa-cho 10-1, Hamamatsu, Japan 430
Tel: 053-460-2445
SY11
M.D.G., EMI Division Yamaha Corporation 1997
VZ24250 708POCP3.3-02B0 Printed in Japan
C
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224
  • Page 225 225
  • Page 226 226
  • Page 227 227
  • Page 228 228
  • Page 229 229
  • Page 230 230
  • Page 231 231
  • Page 232 232
  • Page 233 233
  • Page 234 234
  • Page 235 235
  • Page 236 236
  • Page 237 237
  • Page 238 238
  • Page 239 239
  • Page 240 240
  • Page 241 241
  • Page 242 242
  • Page 243 243
  • Page 244 244
  • Page 245 245
  • Page 246 246
  • Page 247 247
  • Page 248 248
  • Page 249 249
  • Page 250 250
  • Page 251 251
  • Page 252 252

Yamaha QY70 Handleiding

Categorie
Digitale piano's
Type
Handleiding