Yamaha Dante-MY16 Gebruikershandleiding

Merk: Yamaha

Model: Dante-MY16

Type: Gebruikershandleiding

Dante-MY16-AUD & R series

HA Remote Control Guide

3rd Edition: August 2013

Yamaha Commercial Audio

Dante-MY16-AUD HA Remote Control Guide

2 www.yamahaproaudio.com

This guide describes the examples and setting procedures of a system where

you remote-control the head amplifier (hereafter called the HA) of an I/O rack

(Rio3224-D, Rio1608-D, Ri8-D, etc.) connected with the Dante audio network,

via the Dante-MY16-AUD card inserted in a slot in a Yamaha digital mixer

(PM5D, M7CL, LS9, etc.). This solution allows you to remote-control it in a

system where a Dante-compatible I/O rack is added and incorporated, using

your favorite digital mixer as it is.

The setting procedure for a digital mixer varies with the model. For details,

please also refer to the Owner’s Manual of the applicable model.

Table of Contents

System Examples.............................................................................................. 3

Equipment List ................................................................................................... 6

Connections for HA Control ........................................................................... 7

Settings for R series ......................................................................................... 8

Settings by Dante Controller........................................................................ 11

Settings for the Digital Mixer ....................................................................... 12

Yamaha Commercial Audio

Dante-MY16-AUD HA Remote Control Guide

3 www.yamahaproaudio.com

System Examples

LS9 system example

When inserting the Dante-MY16-AUD card into your LS9, you can remote-

control the HA of an I/O rack on the Dante network from the LS9, with just a

simple network connection. From the LS9, each Rio1608-D is recognized and

controlled as two units of AD8HR (one unit for the Ri8-D). Please ensure that

the card bridging an HA control signal is always inserted into slot 1 (for the

LS9-32).

PM5D system example

To remote-control the HA of an I/O rack on the Dante network from the PM5D,

you need to connect the REMOTE terminals between the console and the

card with a serial cable (straight, female–male), in addition to the network

connection.

In a redundantly connected Dante network, the control signal as well as the

audio signal, passes through both circuits. Therefore, even if the primary

circuit is broken, the communication of HA control can continue by using the

secondary circuit.

Slot 1: mode 2

mode 2

LS9

-16

LS9-32

Rio1608-D

Ri8-D

mode 3

Rio1608-D

Rio3224-D

Primary

Secondary

PM5D/PM5D

-RH

Yamaha Commercial Audio

Dante-MY16-AUD HA Remote Control Guide

4 www.yamahaproaudio.com

Multiple console system example

You can also connect multiple consoles onto the Dante network to share an

I/O rack. In this case, although an audio signal can be distributed to multiple

consoles from the same I/O rack by patching with the Dante Controller, the

HA can only be controlled from one of the consoles. In the following example,

the HA is controlled from the PM5D only, and the CL5 only shares an audio

signal. Please see below for details about the system with multiple consoles.

When you connect multiple consoles onto the Dante network to share an I/O

rack, an audio signal can be distributed to multiple consoles from the same

I/O rack, but the HA of the same I/O rack cannot be controlled from multiple

consoles.

It is only when the R series (in NATIVE mode) is controlled from the CL series

that the same I/O rack can be controlled from multiple consoles (in this case,

also the Gain Compensation function can be used). However, even on the

same network, the HA of a different I/O rack can be controlled from other

consoles.

mode 3

PM5D/PM5D-RH

CL5

Rio3224-D

Primary

Secondary

Other Consoles

Gain

Compensation

Gain

Compensation

Native mode

AD8HR mode

Native mode

Other Consoles

Yamaha Commercial Audio

Dante-MY16-AUD HA Remote Control Guide

5 www.yamahaproaudio.com

When the HA is controlled from the CL series, gain of the signal passing

through the network can be kept constant by the Gain Compensation function.

That is, in the example below, even if the HA gain is changed from the CL

series, the level of the audio signal to be input to the PM5D will not fluctuate.

When the HA is controlled from other consoles, the R series is operated in

AD8HR mode; therefore, the Gain Compensation function cannot be used.

Note:

To control nine or more units of R series from one CL series console, you can also

control the R series (in AD8HR mode) via a Dante-MY16-AUD inserted in slot 1.

Examples of the system mixed with AD8HR

The HA can be controlled even in the system mixed with such HA equipment

as the R series, the AD8HR, and the DME24N. However, when you control

these HAs, please ensure that their IDs are unique to each other. The ID of an

AD8HR is automatically assigned in the order of daisy chain connection, and

the ID of a DME24N is set with the DME Designer software. As for the R

series, its virtual AD8HR ID is set from the front panel rotary switch (cf. page

8).

Gain

Compensation

Native mode

AD8HR mode

Other Consoles

Unit ID: 2 = Virtual ID 3, 4

Auto = ID 1, 2

AD8HR

Rio1608-D

Yamaha Commercial Audio

Dante-MY16-AUD HA Remote Control Guide

6 www.yamahaproaudio.com

Equipment List

1. Yamaha digital mixer (PM5D/PM5D-RH, M7CL-32/48, M7CL-48ES,

LS9, DM2000, DM1000) or digital mixing engine (DME64N/24N)

2. Dante-MY16-AUD card (firmware v3.3.9 or later)

3. Dante-compatible Yamaha HA equipment (Rio3224-D, Rio1608-D, Ri8-

D, etc.)

4. PC or Mac where Dante Controller v3.2.9 or later is installed

5. Gigabit network switch, network cable of CAT5e or better

6. D-sub 9-pin straight serial cable (male–female)*

*Precautions for a serial cable:

・ This is not required when you control the HA via the Dante network from

the M7CL-48ES, the LS9, or the CL series. To control the HA from another

digital mixer, a serial cable is required. Moreover, it is required when you

control such HA equipment as the AD8HR from the REMOTE terminal of

the Dante-MY16-AUD card.

・ The serial cable to use is a D-sub 9-pin straight cable, of male–female type.

As an alternative, you can use a straight cable of female–female type with

a gender changer (conversion adapter) of male–male type.

Female

Male

Straight

Female

Male - Male

Yamaha Commercial Audio

Dante-MY16-AUD HA Remote Control Guide

7 www.yamahaproaudio.com

Connections for HA Control

There are three types of the connections for HA remote control and bridge

settings via the Dante-MY16-AUD card, as shown below. By default, no bridge

is active (Mode 4); therefore, you need to set it with the Dante Controller

software (cf. page 11).

Mode 1

An HA control signal is bridged between

slot 1 (in the host equipment) and the

REMOTE terminal on the card (not

bridged to the Dante network). This is

used to directly control HA equipment

via a serial cable from host equipment

with no HA REMOTE terminal, such as

the LS9.

Mode 2

An HA control signal is bridged between

slot 1 (in the host equipment) and the

Dante network (not bridged to the

REMOTE terminal on the card). This is

used to control HA equipment via the

Dante network from host equipment

with no HA REMOTE terminal, such as

the LS9. No serial cable is required.

Mode 3

An HA control signal is bridged between

the REMOTE terminal and the Dante

network (not bridged through a slot).

This is used to control HA equipment

via the Dante network from host

equipment with an HA REMOTE

terminal, such as the PM5D.

Note:

For HA remote control via the Dante-MY16-AUD

card, only one route can be bridged. Therefore,

HA control via the network and HA control via the

REMOTE terminal cannot both be bridged from

the console simultaneously.

mode 1

mode 2

mode 3

DB9

Network

Yamaha Commercial Audio

Dante-MY16-AUD HA Remote Control Guide

8 www.yamahaproaudio.com

Settings for R series

To remote-control the HA of the R series via the Dante-MY16-AUD card, you

should set UNIT ID and the DIP switches at the front panel of the R series as

follows, and then turn on the power.

UNIT ID

A virtual ID as the AD8HR (with eight channels) is decided by the UNIT ID set

here. For example, when you set 1 for UNIT ID, the mixer will recognize the

Rio3224-D as a virtual ID 1 to 4, the Rio1608-D as a virtual ID 1 to 2, and the

Ri8-D as a virtual ID 1.

When you mix different models of the R series or mix other HA equipment

(AD8HR etc.) in the system, please especially ensure that virtual IDs are

unique to each other. Discontinuous UNIT ID and virtual ID numbers (e.g. 1, 3,

4) are acceptable.

UNIT ID

Virtual ID (Hexadecimal)

Rio3224-D

Rio1608-D

Ri8-D

1, 2, 3, 4

1, 2

5, 6, 7, 8

3, 4

9, A, B, C

5, 6

D, E, F, 10

7, 8

AD8HR mode

32ch HA

AD8HR x 4

AD8HR x 2

AD8HR x 1

16ch HA

8ch HA

Rio3224-D

Rio1608-D

Ri8-D

Yamaha Commercial Audio

Dante-MY16-AUD HA Remote Control Guide

9 www.yamahaproaudio.com

Setting examples of mixed models:

System

Inputs

I/O Rack

Configuration

UNIT ID settings

(The numbers in parentheses are virtual IDs)

Rio3224-D

Rio1608-D

Ri8-D

32 ins

Rio1608-D x1

Ri8-D x2

(1, 2)

3, 4

(3, 4)

48 ins

Rio3224-D x1

Rio1608-D x1

(1－4)

(5, 6)

Rio3224-D x1

Ri8-D x2

(1－4)

5, 6

(5, 6)

Rio1608-D x2

Ri8-D x2

1, 2

(1－4)

5, 6

(5, 6)

Rio1608-D x1

Ri8-D x4

(1, 2)

3－6

(3－6)

64 ins

Rio3224-D x1

Rio1608-D x2

(1－4)

3, 4

(5－8)

Rio3224-D x1

Rio1608-D x1

Ri8-D x2

(1－4)

(5, 6)

7, 8

(7, 8)

Rio3224-D x1

Ri8-D x4

(1－4)

5－8

(5－8)

Rio1608-D x3

Ri8-D x2

1－3

(1－6)

7, 8

(7, 8)

Rio1608-D x2

Ri8-D x4

1, 2

(1－4)

5－8

(5－8)

Rio1608-D x1

Ri8-D x6

(1, 2)

3－8

(3－8)

Setting examples of a special case:

As for the system where each single unit of the Rio3224-D, the Rio1608-D, the

Ri8-D, and the AD8HR coexist, if you set UNIT IDs as follows, they will be

recognized as eight units of AD8HR with their IDs unique to each other.

・ AD8HR: ID 1 (automatically assigned in order of daisy chain connection)

・ Ri8-D: UNIT ID 2 (virtual ID 2)

・ Rio1608-D: UNIT ID 2 (virtual ID 3, 4)

・ Rio3224-D: UNIT ID 2 (virtual ID 5 to 8)

Note:

・ The number of units of controllable HA equipment (virtual IDs of AD8HR)

varies with the digital mixer, which can be checked at the EXTERNAL HA

screen etc. The PM5D, the M7CL, the LS9-32, the LS9-16, the DM2000, and

the DM1000 support eight, six, four, two, twelve, and four units, respectively.

Patching of an audio signal is limited only by the number of channels due to

that of cards used, regardless of the limitations above.

Yamaha Commercial Audio

Dante-MY16-AUD HA Remote Control Guide

10 www.yamahaproaudio.com

・ If the R series in NATIVE mode and that in AD8HR mode coexist within one

network, a duplicated UNIT ID between the different modes is acceptable (with

the CL and R series firmware v1.5 or later).

SECONDARY PORT

Flip the DIP switch 4 up for daisy-chain connection, or down for redundant

connection (star connection with switches).

REMOTE

Establish the AD8HR mode (flip DIP switch 5 down). The mixer will recognize

the R series as AD8HR (multiple units).

In this case, however, functions specific to the CL series, such as the Gain

Compensation function, are disabled. In the system where the CL series and

other mixers coexist, to control the HA from only the CL series, you can

operate it as in NATIVE mode.

START UP MODE

Regardless of the DIP switch setting, the R series units in AD8HR mode

always operate in RESUME mode, in which the units start up using their HA

settings assigned prior to the most recent power-off.

Note:

Therefore, if you wish to erase any previous unwanted HA settings, first set DIP

switches 5, 6, 7, 8 up and power-on the R series for at least 30 seconds. Then

turn off the power, and set DIP switch 5 down for AD8HR mode before turning the

power on again.

Yamaha Commercial Audio

Dante-MY16-AUD HA Remote Control Guide

11 www.yamahaproaudio.com

Settings by Dante Controller

When you start Dante Controller, the Network View opens first, and all the

Dante equipment on the network appear. This allows you to set the audio

routing between Dante devices. Click a cell in the intersection of transmit and

receive channels to set an audio route from the upper-right transmit channel

to the lower-left receive channel. When the route is set, a green icon appears.

For details, please refer to the Dante Controller user manual.

Double-click a device name of the Dante-MY16-AUD card (communicating an

HA control signal with host equipment) to open the Device View window. On

the HA Remote page, choose Mode 1, Mode 2, or Mode 3 as a serial bridge

mode for HA remote of the Dante-MY16-AUD card. For details about each

mode, please see “Connections for HA Control” (on page 7).

Note:

If the HA Remote page is not displayed on the Device View window, please check

that Dante Controller v3.2.9 or later and the Dante-MY16-AUD firmware v3.3.9 or

later are used.

Yamaha Commercial Audio

Dante-MY16-AUD HA Remote Control Guide

12 www.yamahaproaudio.com

Settings for the Digital Mixer

On the digital mixer, configure the same settings as those for remote-

controlling other external HA equipment. For details, please also refer to the

Owner’s Manual of the applicable digital mixer.

WORD CLOCK Settings

There are three possibilities for configuring the word clock settings of the

system:

• Use Dante as the master clock. This is the best option when there are

multiple consoles in one network.

• Use the console as the master clock. This is a convenient option when

there is only one console in the system.

• Use an external word clock generator as the master clock. This can be

necessary in studios and broadcast environments when there are other

digital audio systems to synchronize to.

Using Dante as the Master Clock

In the Word Clock menu of each mixer, select any slot input in which a Dante-

MY16-AUD card is installed as the clock source. The Dante network will

automatically select a clock master device to keep the whole network in sync.

Using the Console as the Master Clock

In the Word Clock menu of the mixer, select “Internal 48k” as the clock source (this

is the default selection). Open Dante Controller software and select the Clock

Status tab. Set “Slave to External Clock” for just one of the Dante-MY16-AUD

cards that are installed in the mixer. For the same card, check the “Preferred

Master” option, and this card will transmit the word clock to the rest of the network.

Yamaha Commercial Audio

Dante-MY16-AUD HA Remote Control Guide

13 www.yamahaproaudio.com

Using an External Word Clock Generator

In the Word Clock menu of the mixer, select “Word Clock In” as the clock source.

Open Dante Controller software and select the Clock Status tab. Set “Slave to

External Clock” for just one of the Dante-MY16-AUD cards that are installed in the

mixer. For the same card, check the “Preferred Master” option, and this card will

transmit the word clock to the rest of the network.

EXTERNAL HA Settings

Next, on your digital mixer, open the EXTERNAL HA screen (or the REMOTE

screen). At this screen, you can see the connected external HA equipment

(the R series in this description) virtually mounted onto the rack as AD8HR.

M7CL-48: RACK -> EXTERNAL HA screen LS9-32: RACK -> EXTERNAL HA screen

COMM PORT

Select a port that transmits/receives an HA control signal. For the LS9 or the

M7CL-48ES, choose SLOT 1. The other equipment (such as the M7CL-48/32 and

the PM5D) has no setting (only the HA REMOTE terminal is available).

EXTERNAL HA PORT

Select an audio input port (for eight channels of a slot) for each virtual rack. Make

sure to match the rack number with the virtual ID on the HA device.

When configuring the above settings, you can open a rack from the

EXTERNAL HA screen to control the HA. Moreover, when patching a

corresponding slot input to an input channel, you can adjust the external HA

from the input channel controls.

Yamaha Commercial Audio

Dante-MY16-AUD HA Remote Control Guide

14 www.yamahaproaudio.com

Note:

If the mixer cannot recognize HA equipment and the HA equipment does not

appear on the screen of the mixer, please check the following.

・ Are the Dante-MY16-AUD firmware and Dante Controller updated to a version

that supports the HA remote function? Firmware V3.3.9 or later and Dante

Controller V3.2.9 or later are required.

・ (In the case where a serial cable is used) Are you using a straight cable?

・ (In the case where control is done via the Mini-YGDAI slot) Have you inserted

the Dante-MY16-AUD in SLOT1? Those other than SLOT1 cannot transmit

HA control signals.

・ Is the HA Remote bridge mode of Dante-MY16-AUD set properly?

・ Is AD8HR mode set on the front panel of the R series? Are all the virtual unit

IDs unique to each other?

・ Ensure that a port other than REMOTE and SLOT1 is selected as a MIDI port

on the MIDI SETUP screen of the digital mixer.

Yamaha Dante-MY16 Gebruikershandleiding

Merk: Yamaha

Model: Dante-MY16

Type: Gebruikershandleiding

Download PDF

rapport

in andere talen

English: Yamaha Dante-MY16 User guide
italiano: Yamaha Dante-MY16 Guida utente
русский: Yamaha Dante-MY16 Руководство пользователя
français: Yamaha Dante-MY16 Mode d'emploi
español: Yamaha Dante-MY16 Guía del usuario
Deutsch: Yamaha Dante-MY16 Benutzerhandbuch
português: Yamaha Dante-MY16 Guia de usuario
dansk: Yamaha Dante-MY16 Brugervejledning
suomi: Yamaha Dante-MY16 Käyttöohjeet
čeština: Yamaha Dante-MY16 Uživatelská příručka
svenska: Yamaha Dante-MY16 Användarguide
Türkçe: Yamaha Dante-MY16 Kullanici rehberi
polski: Yamaha Dante-MY16 instrukcja
română: Yamaha Dante-MY16 Manualul utilizatorului

Yamaha Dante-MY16 Gebruikershandleiding

Yamaha Dante-MY16 Gebruikershandleiding

in andere talen

Gerelateerde artikelen