Yamaha V5 Gebruikershandleiding

Merk: Yamaha

Model: V5

Type: Gebruikershandleiding

R Remote Version 5.8 User’s Guide 1

R Remote Version 5.8 User’s Guide

Thank you for choosing a Yamaha product.

This user’s guide explains setup, firmware update and use of "R Remote," a Windows/Mac application that lets

you make parameter settings for the Rio3224-D/Rio1608-D/Ri8-D/Ro8-D/RSio64-D/RMio64-D/Rio3224-

D2/Rio1608-D2 (subsequently "R series") and the Tio1608-D units.

This application lets you edit the parameters of up to twenty-four devices from a single computer. Even if the

device is not connected, you can mount it virtually and edit its settings beforehand.

Up to two computers in which R Remote is installed can be connected to a single device. This means, for

example, that the main operator could operate a console such as the CL while two assistants make detailed

adjustments at the other locations.

■ NOTICE

⠂ Yamaha Corporation owns exclusive copyrights for the R Remote, the firmware for each device, and the user’s guide.

⠂ It is prohibited to duplicate or modify the firmware, software or manuals, in part or in their entirety, without permission from the copyright

owner.

⠂ The illustrations and screens as shown in this User’s Guide are for instructional purposes, and may appear somewhat different from the

screens which appear on your computer.

⠂ This software was not produced with the intention to support touch-panel operation in Windows 10 / Windows 11, so we cannot

guarantee operation if a touch-panel is used.

⠂ Dante is a trademark of Audinate.

⠂ Windows is a registered trademark of Microsoft ® Corporation in the United States and other countries.

⠂ Mac and macOS are trademarks of Apple Inc., registered in the U.S. and other countries.

⠂ The company names and product names in this document are the trademarks or registered trademarks of their respective companies.

⠂ This guide predominantly uses screenshots of Windows. However, Mac screenshots are used when instructions of the function apply

only to the Mac.

⠂This product incorporates open source software. For information about the software, refer to the “License Agreement,” accessed from the

“Legal” button on the “About R Remote” window.

⠂ Software may be revised and updated without prior notice.

R Remote Version 5.8 User’s Guide 2

Contents

■ NOTICE ............................................................................................................................................................... 1

Using the PDF manual ............................................................................................................................................. 4

System Requirements ............................................................................................................................................. 4

Operation ................................................................................................................................................................. 4

Setup ...................................................................................................................................... 5

Install (or uninstall) the R Remote ........................................................................................................................... 5

Set on the devices ................................................................................................................................................... 6

UNIT ID ............................................................................................................................................................................. 6

IP address ........................................................................................................................................................................ 6

Connection ........................................................................................................................................................................ 7

START UP MODE ............................................................................................................................................................ 8

Connect the computer and the devices ................................................................................................................... 9

Power-on the devices .............................................................................................................................................. 9

Specify the computer's IP address ........................................................................................................................ 10

For Windows ....................................................................................................................................................................10

For Mac............................................................................................................................................................................12

Use Dante Controller or the CL/QL series console to specify the routing

................................................................ 12

Operating R Remote ............................................................................................................ 13

Menu bar ................................................................................................................................................................ 13

Areas of the screen ................................................................................................................................................ 14

Device Selection Area .....................................................................................................................................................15

Information Display Area..................................................................................................................................................15

Main Area ........................................................................................................................................................................16

Edit window ......................................................................................................................................................................18

“Network Setup” dialog box ................................................................................................................................... 28

“Device Information” dialog box ............................................................................................................................. 29

“IP Address” dialog box ......................................................................................................................................... 30

“Properties” dialog box ........................................................................................................................................... 31

Updating the Firmware ........................................................................................................ 32

Precautions ............................................................................................................................................................ 32

Updating – Operation Overview ............................................................................................................................ 32

Connecting the Computer to the Device ................................................................................................................ 33

Network Settings .................................................................................................................................................... 34

R Remote Firmware Updater ................................................................................................................................. 34

Update operation ................................................................................................................................................... 36

Detecting the device .............................................................................................................................................. 37

In case of failure in updating the firmware ............................................................................................................. 37

Messages .............................................................................................................................................................. 39

■ Error messages ...........................................................................................................................................................39

■ Warning Messages .....................................................................................................................................................39

■ Confirmation Messages...............................................................................................................................................39

R Remote Version 5.8 User’s Guide 3

■ Other Messages ..........................................................................................................................................................40

Troubleshooting .................................................................................................................. 41

Decimal/hexadecimal conversion table ................................................................................................................. 42

R Remote Version 5.8 User’s Guide 4

Using the PDF manual

 You can move to the corresponding page by clicking on links in the table of contents or in the text.

 If you want to find information on a specific topic, function or feature, select “Find” or “Search” from the

Adobe Reader “Edit” menu and enter a key word to locate the related information anywhere in the document.

 You can also click on desired items and topics you want to refer to in the “Bookmarks” index to the left of the

main display window, and jump to the corresponding page. (Click the “Bookmarks” tab to open the index if it

is not displayed.)

System Requirements

In order to use R Remote, you'll need the following items.

● A computer equipped with the following conditions:

Windows 10, Windows 11

(R Remote supports 64-bit Windows only.)

macOS 10.15, macOS 11, macOS 12, macOS 13

CPU

Intel Core i3 or higher, Apple M1,M2 processor

HDD 120MB or more

Supported Devices (*)

Rio3224-D, Rio1608-D, Ri8-D, and Ro8-D (firmware V3.11 or later)

RSio64-D (firmware V3.10 or later)

RMio64-D (firmware V3.11 or later)

Tio1608-D, Rio3224-D2, and Rio1608-D2 (firmware V1.00 or later)

Others



An Ethernet connector (1000BASE-T or higher recommended)

 Ethernet cable (CAT5e or better)

 Network switch (with gigabit Ethernet support), when connecting devices

via a Dante network

 Dante Controller must be installed. (**)

(*) When the firmware version of the target device is out-of-date and unsupported, you will need to update the

firmware by using exclusive update software for each product.

(**) You can download Dante Controller from the download page of the following Audinate website.

https://www.audinate.com/products/software/dante-controller/

The Minimum System Requirements described above are applied to the R Remote version 5.8. Keep in mind

that the software is often updated and the system requirements are subject to change. You can check the latest

version information of each program and its system requirements at the following website

https://www.yamahaproaudio.com/

Operation

Keyboard Shortcuts

<Windows modifier key> (<Mac modifier key>) + <key> or click shows the shortcut keys. For example, <Ctrl>

(<command>) +click means “press <Ctrl> under Windows or <command> under Mac, then click.”

Right Click

On Mac click while holding down the <control> key.

R Remote Version 5.8 User’s Guide 5

Setup

The setup workflow is shown below.

Install the R Remote

Set on the devices

Connect the computer and the devices

You cannot connect to a device connected from another subnet via DANTE DOMAIN

MANAGER.

Power-on the devices

Specify the computer's IP address

Use Dante Controller or the CL/QL series console to specify the routing

For details on connections and settings for the devices, refer also to the owner's manual of your devices.

Install (or uninstall) the R Remote

The installation procedure is as follows.

1. Logon to Windows or Login to Mac with administer account.

2. After decompressing the downloaded file, double-click “setup.exe” (Windows) or “Install R Remote

Vxxx.pkg” (Mac)(xxx is version) in the decompressed file location.

The R Remote setup wizard will appear.

Under Windows, the “User Account Control” dialog box may appear. Click [Continue] or [Yes].

3. Proceed with the installation as directed by the instructions in the screen.

To uninstall the software (remove the application),

Windows:

In Control Panel, click [Programs and functions] or [Uninstall a program], then select the item you want to

uninstall, and click [Uninstall or change].

A dialog box will appear; follow the instructions in the screen to uninstall the software.

If the “User Account Control” dialog box appears, click [Continue] or [Yes].

Mac:

Double-click "Uninstall R Remote.app" which is included in the installer.

R Remote Version 5.8 User’s Guide 6

Set on the devices

Set the DIP switches and [UNIT ID] rotary switch of the unit, taking note of the following settings.

On the Rio3224-D2 and Rio1608-D2, set the following settings using the front panel display of the device.

UNIT ID

 Set a unique UNIT ID that will not conflict with the other device, over a range of 1 to 24 (hexadecimal 18). R

Remote will not detect units with a setting of 0 or 25 or higher. (For details on converting between decimal

and hexadecimal, refer to the "Decimal/hexadecimal conversion table" on page 42)

 Rio3224-D2 and Rio1608-D2: Set the “UNIT ID” on the SETUP menu.

 For devices excepting the Rio3224-D2 and Rio1608-D2: Set the DIP switches to the following combinations.

Settings

Switch

UNIT ID ranging from 1 to F

(decimal values 1 to 15)

(1 up)

UNIT ID ranging from 10 to 18

(decimal values 16 to 24)

(1 down)

IP address

Specify the IP address that the R Remote uses for control.

(The IP address set here is different from the IP address of the Dante network.)

For devices other than the Tio1608-D, the RMio64-D, the Rio3224-D2 and the Rio1608-D2

Settings

Switch

Auto IP

(The IP address will be automatically set to 169.254.xxx.xxx.)

(2 and 3 up)

DHCP

(The IP address assigned by the DHCP server will be used.)

(2 down, 3 up)

Static IP (Auto)

[The IP address will be set to 192.168.0.xxx (xxx= UNIT ID).]

(2 up, 3 down)

Static IP (Manual)

(Set the IP address to the value specified on the R Remote)

(2 and 3 down)

The first time that you connect an R series unit to your computer, set this to something other than Static IP

(Manual). If you want to use the Static IP (Manual) setting, first specify the IP address on the R Remote and

then switch to Static IP (Manual).

If the network consists only of Dante devices and R Remote, we recommend that you use the Auto IP setting.

If you are connecting to an existing network, select DHCP as needed.

If you want to use zoning to set the IP address, or want to connect to an existing network but use a static IP

address, choose Static IP (Manual) and use the R Remote to set the IP address.

R Remote Version 5.8 User’s Guide 7

Tio1608-D

Settings

Switch

Auto IP (Link Local)

(The IP address will be automatically sets to 169.254.xxx.xxx.)

(5 and 6 up)

DHCP

(The IP address assigned by the DHCP server will be used.)

(5 up, 6 down)

Static IP (Auto)

[The IP address will be set to 192.168.0.xxx (xxx= UNIT ID).]

(5 down, 6 up)

Static IP (Manual)

(Set the IP address to the value specified on the R Remote)

(5 and 6 down)

RMio64-D

The IP address is set by using the R Remote since RMio64-D has no DIP switches for setting the IP address.

Refer to the “IP Address” dialog box for more information.

Rio3224-D2-D and Rio1608-D2

Set the “NETWORK MODE” in the SETUP menu.

Connection

For devices other than the RMio64-D, the Rio3224-D2 and the Rio1608-D2

Settings

Switch

DAISY CHAIN

(4 up)

REDUNDANT

(4 down)

RMio64-D

Rio3224-D2-D and Rio1608-D2

Set the “SECONDARY PORT” in the SETUP menu.

Settings

Switch

DAISY CHAIN

(1 up)

REDUNDANT

(1 down)

R Remote Version 5.8 User’s Guide 8

START UP MODE

If a CL/QL series unit is not connected, we recommend that you set START UP MODE to RESUME. If this is

set to REFRESH, settings must be transmitted from the R Remote each time the R series unit is restarted.

Rio3224-D, Rio1608-D, Ri8-D and Tio1608-D

Settings

Switch

REFRESH

When the device is turned on, the following settings are initialized and

inputs/outputs are muted.

・HA GAIN (-6 dB)

・+48V (OFF)

・HPF (OFF)

・HPF FREQ (80Hz)

・Gain Compensation (OFF) (Except for Tio1608-D)

To use the device after initialization, you need to: turn the

device off  set the DIP switches to RESUME turn the device on.

(7 and 8 up)

RESUME

(The unit starts up using the settings assigned prior to the most recent

power off.)

(7 down, 8 up)

RSio64-D

Settings

Switch

NORMAL

(Start up normally with the settings of the previous start-up.)

(7 and 8 up)

INITIALIZE

The following settings are initialized when the device is turned on.

・SLOT 1-4 SRC (OFF)

・WORD CLOCK SELECT (DANTE/48kHz)

・USER PATTERN (same routing configuration as the preset PATTERN # 1)

・Static IP (Manual) (0.0.0.0)

・PANEL LOCK (Unlock)

・Dante PATCH (All OFF)

・Dante DEVICE LABEL (Y001-Yamaha-RSio64-D-123456) (*1)

To use the device after initialization, you need to: turn the

device off  set the DIP switches to NORMAL  turn the device on.

(7 down, 8 up)

(*1) The third and fourth characters of the Dante DEVICE LABEL depend on the device settings of DIP switch 1 and the

SETUP [UNIT ID] rotary switch. The lower six digits depend on the lower six digits of the unit’s MAC address.

R Remote Version 5.8 User’s Guide 9

Rio3224-D2-D and Rio1608-D2

Set the “START UP MODE” in the SETUP menu.

Settings

REFRESH

When the device is turned on, the following settings are initialized and inputs/outputs are muted.

・HA GAIN (-6 dB)

・+48V (OFF)

・HPF (OFF)

・HPF FREQ (80Hz)

・GAIN COMPENSATION (OFF)

・

COMPENSATION GAIN (-6 dB)

RESUME

(The unit starts up using the settings assigned prior to the most recent power off.)

REFRESH w/o MUTE

(The settings are initialized when turned the device on. The initial values are the same as for REFRESH.

However, inputs and outputs are not muted.)

Connect the computer and the devices

Use an Ethernet cable to connect the computer and the devices.

If you selected DAISY CHAIN in “SECONDARY PORT” on the above, connect the Dante connectors of the

devices in a daisy chain to the computer.

If you selected REDUNDANT in “SECONDARY PORT” on the above, connect the computer to the network

switch that is connected to the Dante [PRIMARY] connector.

You cannot connect to a device connected from another subnet via DANTE DOMAIN MANAGER.

Power-on the devices

Power-on the devices. The DIP switch settings, the rotary switch settings and the settings in the SETUP menu

after power-on will not be applied until the next power-on.

R Remote Version 5.8 User’s Guide 10

Specify the computer's IP address

Specify the computer's IP address so that it can communicate with the devices.

The method of making this setting depends on whether you're using Windows or Mac. Also, the computer's IP

address setting will differ depending on the IP address specified in "Set on the devices."

If you're using Mac, click the link.

For Windows

Accessing the Control Panel

Select [Start]  [Windows System]  [Control Panel].

TCP/IP Settings

Make TCP/IP settings for the computer as follows.

1. Access the Control Panel, then click or double-click [Network and Sharing Center] or [View

network status and tasks].

The “Network and Sharing Center” is displayed.

2. Click [Manage network connection] or [Change adapter settings] from the “Tasks” list located in

the left side of “Network and Shearing Center” window, then double-click [Local Area Connection].

The “Local Area Connection Status” dialog box will be displayed.

・The “User Account Control” dialog box may appear. Click [Continue] or [Yes].

・If the “Local Area Connection properties” dialog box appears, skip ahead to step 4.

3. Click [Properties].

The “Local Area Connection properties” dialog box will be displayed.

The “User Account Control” dialog box may appear. Click [Continue] or [Yes].

4. Select [Internet Protocol Version 4(TCP/IPv4)], then click [Properties].

The “Internet Protocol Version 4(TCP/IPv4) Protocol” dialog box will be displayed.

R Remote Version 5.8 User’s Guide 11

5. Make the following settings according to the IP address setting you made in "Set on the devices."

Auto IP or DHCP

Static IP (Manual))

Click [Obtain an IP address automatically].

Click [Use the following IP address:].

As the IP address, enter "192.168.0.xxx (a value in the

range 1 to 254 that does not conflict with any other

device, including the target devices), and enter

"255.255.255.0" as the subnet mask.

The 192.168.0.101 shown below is an example.

If you're using Static IP (Manual), specify the setting that's appropriate for your network. For details,

consult your network administrator.

6. Click [OK].

Proceed to "Use Dante Controller or the CL/QL series console to specify the routing."

R Remote Version 5.8 User’s Guide 12

For Mac

Make TCP/IP settings for the computer as follows.

1. Click [System Preferences][Network].

The “Network” dialog box will be displayed.

2. Click the service that you want to connect to the device.

If you're using the Ethernet port that's built into the Mac, click [Ethernet].

3. Make the following settings according to the IP address setting you made in "Set on the devices"

Auto IP or DHCP

Static IP (Manual)

In "Configure IPv4," choose [Using DHCP].

In “Configure IPv4,” choose [Manually]. As the IP

address, enter "192.168.0.xxx (a value in the range 1 to

254 that does not conflict with any other device, including

the target devices), and enter "255.255.255.0" as the

subnet mask.

The 192.168.0.101 shown below is an example.

If you're using Static IP (Manual), specify the setting that's appropriate for your network. For details,

consult your network administrator.

4. Click [Apply] button, then close “Network” dialog box.

Use Dante Controller or the CL/QL series console to specify the routing

If you're using Dante Controller to specify the routing, refer to "Dante Controller User’s Guide."

If you're using a CL/QL series console to specify the routing, refer to the each Reference Manual.

This completes the setup.

R Remote Version 5.8 User’s Guide 13

Operating R Remote

Start R Remote.

Windows 10 users: click [Start][Yamaha R Remote][R Remote]

Windows 11 users: click [Start][All apps][Yamaha R Remote][R Remote]

Mac users: click [Go][Applications] double-click [R Remote].

 When you start R Remote, the “Network Setup” dialog box may appear, allowing you to select the

computer's network card that will be used for communication with the devices. If this appears, click the

network card that is connected to the device, and then click the [Apply] button.

Menu bar

The commands that can be executed by R Remote can be found here, grouped by category.

Click here to see a list of commands.

Command

Summary

Dialog box that appears

[File]

[Open]

Opens a previously-saved file (rrmt

format or rrm format).

NOTICE

If you open the file when devices are

connected, the settings will be

applied to the devices. Be aware that

if a CL/QL series console is also

connected, its settings will be

overwritten.

“Open File” dialog box

[Save As]

Saves the file. It will have a file name

extension of rrmt, and will be usable

only by R Remote.

“Save File” dialog box

[Network Setup]

Selects the computer’s network

adapter that will be used to

communicate with the devices.

“Network Setup” dialog box

[Device Information]

Displays information about the

devices that are connected.

“Device Information” dialog box

[Quit] *1

Quits R Remote.

---

[Tool]

[Firmware Update]

Calls up the window to update the

firmware.

R Remote Firmware Updater

[About] *1

[About R Remote]

Displays details such as the software

version of R Remote.

“

About R Remote” dialog box

*1 Mac users: [Quit] and [About] are located in the R Remote menu.

R Remote Version 5.8 User’s Guide 14

Areas of the screen

The R Remote screen is broadly divided into three areas: the Device Selection Area, the Information Display

Area, and the Main Area.

R Remote Version 5.8 User’s Guide 15

Device Selection Area

When you click a display switching button, the corresponding device is shown in the

information display area and in the main area.

With a display switching button selected, pressing the left mouse button makes all indicators

of the corresponding device blink, allowing you to identify the corresponding unit.

Also shows an attention icon depending on the device status.

When you right-click a display switching button, the following context menu appears.

Command

Summary

[Mount]

Opens the "Mount" window. Select the device that you want to mount.

[Connect]

Synchronizes with the selected device.

[Disconnect]

Disconnects from the selected device.

[Properties]

Open the “Properties” dialog box.

[Summary]

(Rio3224-D2 and Rio1608-D2 only)

Displays the selected device summary (REPORT).

[Log]

(Rio3224-D2 and Rio1608-D2 only)

Save the device log. The file is named automatically according the following format.

In case of Rio3224-D2: Rio3224-D2_201712261339.log

* The numbers after “_” indicate the year, month, day and time.

The connection status is shown below each display switching button.

Indication

Status

VIRTUAL The device is mounted without the existence of the actual device.

Alternately, communication is impossible due to incorrect settings having been made.

BLANK

The device is not powered-on or the device is not connected to the computer.

CONNECTED

Currently synchronized with the device.

DISCONNECTED Synchronization with the device is possible, but is currently disconnected by the

[Disconnect] command. Alternatively, communication has been interrupted, or

connection failed.

DUPLICATED More than one device of the same UNIT ID exists. Eliminate any UNIT ID conflict

between devices.

Information Display Area

This area shows the UNIT ID and name of the selected device.

To check the firmware version or IP address, choose [File] menu -> [Device Information] to open the “Device

Information” dialog box.

R Remote Version 5.8 User’s Guide 16

Main Area

This area shows the state of the selected device and allows basic parameter editing. The display depends on

the model.

For Rio3224-D / Rio1608-D / Ri8-D / Tio1608-D / Rio3224-D2 / Rio1608-D2

The screen is explained here using the Rio3224-D as an example. The number of items in the HA display area

differs depending on the model.

The Edit window opens if you double-click or right-click and choose [Open Edit Window] anywhere other than

on a controller.

① HA display area

Here you can view and edit HA settings for the Rio3224-D / Rio1608-D / Ri8-D / Tio1608-D / Rio3224-D2 /

Rio1608-D2 unit.

If you press the left mouse button on an area that shows the device's jack number, the indicator of the

actual device's corresponding jack will light.

a. [+48V] button

Turns phantom power on/off for each channel.

b. GAIN knob

Specifies the analog gain for the HA of the device. The current setting is shown in the numeric box

located below the knob.

You can double-click a numeric value box and enter a value directly from the keyboard.

The level meter located at thes immediate right of the knob indicates the input level of the

corresponding port.

On the knobs, you can use the following shortcuts and context menu.

Action

Operation

<Ctrl> (<command>) + click

Sets analog gain to the default value (-6 dB).

<Ctrl> (<command>) + <Shift> + click

Sets the analog gain to 0 dB.

R Remote Version 5.8 User’s Guide 17

Action

Operation

Right click

Displays the following context menu.

[All Default]

Sets the analog gain of all channels to the default

value (-6 dB).

[All 0dB]

Sets the analog gain of all channels to 0 dB.

c. [HPF] button

This is an on/off switch for the high-pass filter that is built into the HA of the device. To specify the cutoff

frequency, make settings in the Edit window.

② [+48V MASTER] indicator

Indicates the master phantom power on/off status for the device (the on/off setting is switched on the

device itself).

③ [SYSTEM] indicator / [SYNC] indicator

Indicates the status of the device or the Dante status. When you move the mouse cursor to this area, the

display content appears as a popup. Also shows an information icon or attention icon depending on

the device status.

④ [PEAK HOLD] button

If this button is on, the peaks of each level meter are held. When you turn this off, the peaks that had been

held are cancelled.

R Remote Version 5.8 User’s Guide 18

Edit window

This appears if you double-click in the main area other than on a controller, or if you right-click and choose

[Open Edit Window].

Here you can view and edit detailed HA settings for the device. To close the window, click the [x] button in the

upper right if you're using Windows, or click the [x] button if you're using Mac.

The screen is explained here using the Rio3224-D as an example. The number of Port select tabs differs

depending on the model.

① Device name

Shows the UNIT ID number and name of the device.

② [PEAK HOLD] button

If this button is on, the peaks of each level meter are held. When you turn this off, the peaks that had been

held are cancelled.

③ Port select tab

For the Rio3224-D, Rio1608-D, Rio3224-D2 or Rio1608-D2, these tabs switch the ports that are shown.

④ Port index

Indicates the port number of the device. When you press this with the left mouse button, the indicator of

the corresponding port of the device will light.

⑤ [+48V] button

Turns the HA phantom power on/off.

⑥ [A.GAIN] knob

Specifies the analog gain for the HA of the device. The current setting is shown in the numeric box located

below the knob.

You can double-click a numeric value box and enter a value directly from the keyboard.

The level meter located at the immediate right of the knob indicates the input level of the corresponding

port.

R Remote Version 5.8 User’s Guide 19

On the knobs, you can use the following shortcuts and context menu.

Action

Operation

<Ctrl> (<command>) + click

Sets analog gain to the default value (-6 dB).

<Ctrl> (<command>) + <Shift> + click

Sets analog gain to 0 dB.

Right click Displays the following context menu.

[All Default]

Sets the analog gain of all channels to the default value (-6

dB).

[All 0dB]

Sets the analog gain of all channels to 0 dB.

⑦ [GC] button

Switches on/off the gain compensation that regularizes the signal level on the audio network. If this is on,

the gain value fixed by gain compensation is displayed, and subsequent changes to analog gain is

compensated by the compensation gain within the device; audio is transmitted to the Dante network at the

gain value that was fixed immediately before this was enabled.

There are limits to the amount of gain compensation. The maximum compensation is 24 dB when turning the knob

toward the left, and 48 dB when turning the knob toward the right. For example if you apply gain compensation at 30

dB, compensation is maintained until you set the analog gain to 6 dB, but if you set the analog gain to 4 dB, the gain

value that is output will be 28 dB. If in this state you return the setting to 6 dB or higher, compensation maintains the

level at 30 dB.

⑧ [FREQ] knob / [HPF] button

Switches on/off the high-pass filter that is built into the HA of the device, and adjusts the cutoff frequency.

The current setting is shown in the numeric box located below the knob.

If you <ctrl> (<command>) + click above the [FREQ] knob, the cutoff frequency is set to the default value

(80 Hz).

R Remote Version 5.8 User’s Guide 20

For Ro8-D

The Ro8-D has no settings that can be operated, so only the [SYSTEM] indicator and [SYNC] indicator are

shown.

① [SYSTEM] indicator / [SYNC] indicator

Indicates the status of the device or the Dante status. When you move the mouse cursor to this area, the

display content appears as a popup. Also shows an information icon or attention icon depending on

the device status.

R Remote Version 5.8 User’s Guide 21

For RSio64-D

You can change the RSio64-D settings.

① CARD NAME

This indicates the names of the cards installed in slots 1 to 4. If nothing is installed, “----” will appear.

If the MY8-AE96 is installed, “AE96S(w/SRC)” will appear if the SRC function in the card is on.

② IN/OUT PORT

This indicates the number of input and output ports for the cards installed in slots 1 to 4. If no card is

installed, “--” will appear.

③ SLOT1～4 [LOCK] indicators

This indicates the word clock status for slots 1 to 4. If the word clock is operating normally, this indicator

will be green.

Off

There is no card in the slot. Or, an unsupported card is in the slot.

Green (On)

LOCK

Indicates that a clock synchronized with the clock source selected with the [WORD

CLOCK] select key is being input from the card. If an external device is connected to

the corresponding slot, input/output is occurring properly between that device and the

RSio64-D. If the sampling frequency is close, this status may be displayed even if not

synchronized.

Green (Flashing)

SYNC ERROR

A valid clock is being input from the card, but is not synchronized with the clock source

selected with the [WORD CLOCK] select key. If an external device is connected to the

corresponding slot, input/output cannot occur correctly between that device and the

RSio64-D. Turn SRC ON for correct input/output.

Red (On)

UNLOCK

A valid clock is not being input from the card. If an external device is connected to the

corresponding slot, input/output cannot occur correctly between that device and the

RSio64-D.

Red (Flashing)

WRONG WORD

CLOCK

The frequency of the clock source selected with the [WORD CLOCK] select key is

outside of the operating frequency range for the card inserted in the slot. Either set the

frequency of the clock source within the operating range for the card, or turn [SRC] ON.

For an analog card, if you turn [SRC] ON, the frequency is set to the 48kHz built into

the RSio64-D.

R Remote Version 5.8 User’s Guide 22

④ SLOT1～4 [SRC] indicators

Indicate the Sampling Rate Converter (SRC) status for slots 1 to 4.

Off

SRC is off.

Green (On)

SRC is on, and the clock selected with the SRC WCLK DIP switches on the RSio64-D

is being input correctly.

Red (On) SRC is on, but an appropriate clock is not being input. The clock selected with the SRC

WCLK DIP switches on the RSio64-D is either not being input or is not within the

operating range. Either turn SRC off, or change the DIP switch settings.

Use the SRC WCLK DIP switches on the RSio64-D to set the SRC clock sent to the Mini-YGDAI card

inserted in the slot.

⑤ SLOT1～4 [SRC] buttons

Used to turn SRC on/off at both IN and OUT for each slot.

⑥ WORD CLOCK source

Indicates the SRC word clock source status for slots 1 to 4 the RSio64-D.

SLOT

When using the word clock signal being input from the card in the slot.

WCLK IN When using the word clock signal being input from the WORD CLOCK IN connector on

the rear panel.

CARD

When the SRC function in the card is on.

----

If there is no card in the slot.

⑦ WORD CLOCK select button

Used to select the word clock source for the RSio64-D.

 WORD CLOCK WCLK IN indicator

 WORD CLOCK SLOT1 1/2 indicator

 WORD CLOCK DANTE indicator

Indicates the word clock source status for the RSio64-D.

WCLK IN On when using the word clock signal being input from the WORD CLOCK IN connector

on the rear panel of the RSio64-D. Flashes*1 if there is no valid word clock input.

SLOT1 1/2 On when using the word clock for channels 1/2 of slot 1 for the RSio64-D. Flashes*1 if

there is no valid word clock input. When using MY8-AEB*2, the word clock for channels

7/8 is used.

DANTE

On when using the word clock for the Dante network*3. (If there is no valid Dante signal

input, the internal Dante module will generate a clock.)

*1 When flashing, Dante word clock*3 input/output is used.

*2 If you are using MY8-AEB, set the AE⇔ RSVD switch for the card to RSVD.

*3 If you make changes to the frequency of the Dante word clock, use Dante Controller.

R Remote Version 5.8 User’s Guide 23

⑧ [CURRENT PATTERN] button

If you click this button, the currently selected routing pattern on the RSio64-D is displayed. If you switch

the routing pattern on the RSio64-D, it will be applied in 3 seconds.

⑨ [USER PATTERN] button

Click this button to open the window for setting the audio routing user pattern in the RSio64-D.

 PRESET button

As a template for editing the patch, you can call by selecting from preset patterns 1-7.

 CLEAR ALL button

Clear all patches.

⑩ POWER INT indicator

Indicates the status of the AC IN power supply for the RSio64-D.

R Remote Version 5.8 User’s Guide 24

⑪ POWER EXT indicator

Indicates the status of the EXT DC INPUT power supply for the RSio64-D. If the power supply is on, this

indicator will be on.

⑫ [SYSTEM] indicator/[SYNC] indicator

Indicates the status of the device or the Dante status. When you move the mouse cursor to this area, the

display content appears as a popup. Also shows an information icon or attention icon depending on

the device status.

R Remote Version 5.8 User’s Guide 25

For RMio64-D

You can change the RMio64-D settings.

① MADI [SRC ON] indicator

MADI [SRC ON] button

Switches the SRC (Sampling Rate Converter) on and off.

② MADI [SRC WCLK IN] indicator

MADI [SRC WCLK IN] button

Use this button to select whether to use (indicator on) or not use (indicator off) the word clock input from

the MADI WCLK IN FOR SRC jack on the rear panel of the RMio64-D as a standard clock for SRC.

③ MADI [INPUT RATE Fs 44.1kHz] indicator

MADI [INPUT RATE Fs 48kHz] indicator

Automatically detect and indicate whether the MADI input signal is 44.1 kHz or 48 kHz.

Both indicators remain off if there is no valid MADI input signal.

④ MADI [INPUT RATE 1Fs] indicator

MADI [INPUT RATE 2Fs] indicator

MADI [INPUT RATE 4Fs] indicator

MADI [INPUT RATE] 1Fs/2Fs/4Fs button

Select either 1Fs (1x), 2Fs (2x), or 4Fs (4x), based on the MADI input frequency. For example, if the MADI

input signal is 192 kHz (4x 48 kHz), confirm that the MADI INPUT RATE Fs 48kHz indicator is on and then

select “4Fs”.

When “2Fs” is selected, the unit automatically detects the frame frequency (48 kHz/96 kHz) of the MADI

input signal.

⑤ MADI [STATUS INPUT] status

MADI [STATUS OUTPUT] status

Display information regarding the MADI input and output signals (frame frequency/number of channels).

R Remote Version 5.8 User’s Guide 26

⑥ WORD CLOCK [WCLK IN] indicator

WORD CLOCK [MADI] indicator

WORD CLOCK [DANTE] indicator

WORD CLOCK [WCLK IN/MADI/DANTE] buttons

Used to select the word clock source.

WCLK IN Uses the word clock signal being input from the WORD CLOCK IN connector on the

rear panel of RMio64-D. The indicators flash when there is no valid word clock input.

MADI

Uses the word clock of the MADI input signal. The indicators flash when there is no

valid word clock input.

DANTE

Uses the word clock of the Dante network.

⑦ WORD CLOCK [Fs] indicator

Indicates the word clock frequency at which the unit is operating. Flashes when not synchronized.

⑧ [EXTERNAL CONTROL] indicator

This indicator comes on when there is a valid parameter that can be operated only externally by remote

control.

Refer to “Remote Control” in the RMio64-D Owner's Manual for details about parameters that can be

operated by remote control.

⑨ [SYSTEM] indicator /[SYNC] indicator

Indicates the status of the device or the Dante status. When you move the mouse cursor to this area, the

display content appears as a popup. Also shows an information icon or attention icon depending on

the device status.

R Remote Version 5.8 User’s Guide 27

For Tio1608-D

You can change the Tio1608-D settings.

① Device name

Shows the UNIT ID number and name of the device.

② [PEAK HOLD] button

If this button is on, the peaks of each level meter are held. When you turn this off, the peaks that had been

held are cancelled.

③ Port select tab

These tabs switch the ports that are shown.

④ Port index

Indicates the port number of the device. When you press this with the left mouse button, the indicator of

the corresponding port of the device will light.

⑤ [+48V] button

Turns the HA phantom power on/off.

⑥ [A.GAIN] knob

Specifies the analog gain for the HA of the device. The current setting is shown in the numeric box located

below the knob.

You can double-click a numeric value box and enter a value directly from the keyboard.

The level meter located at the immediate right of the knob indicates the input level of the corresponding

port.

On the knobs, you can use the following shortcuts and context menu.

Action

Operation

<Ctrl> (<command>) + click

Sets analog gain to the default value (-6 dB).

<Ctrl> (<command>) + <Shift> + click

Sets analog gain to 0 dB.

Right click Displays the following context menu.

[All Default]

Sets the analog gain of all channels to the default value (-6

dB).

[All 0dB]

Sets the analog gain of all channels to 0 dB.

R Remote Version 5.8 User’s Guide 28

⑦ [FREQ] knob / [HPF] button

Switches on/off the high-pass filter that is built into the HA of the device, and adjusts the cutoff frequency.

The current setting is shown in the numeric box located below the knob.

If you <ctrl> (<command>) + click above the [FREQ] knob, the cutoff frequency is set to the default value

(80 Hz).

“Network Setup” dialog box

This appears when you choose [File] menu -> [Network Setup].

Here you can select the network interface card of the computer that will be used to communicate with the

devices (subsequently called “the network card”).

NOTICE The various parameter settings are initialized if you change network cards. In order to use the current settings later, please save

the settings to a file and change the network card.

① Network card list

Select the network card that will be used to communicate with device. When you double-click a network

card, the network card you double-clicked is selected and the dialog box closes.

If you only want to make settings without connecting a device, select [Offline]. If you select a network card

while the status is [Online], data transmission load increases for the connected network.

② [OK] button

Update the settings and closes the dialog box.

③ [Cancel] button

Close the dialog box without updating the settings.

R Remote Version 5.8 User’s Guide 29

“Device Information” dialog box

This appears when you choose [File] menu -> [Device Information].

This lists information about the devices that are connected.

① Device list

By right-clicking the name of an item such as Unit ID, you can select the items that are shown.

 Unit ID

Shows the UNIT ID of the device.

 Product

Shows the model name of the device.

 Name

Shows the device name. This name can be edited in Dante Controller.

 Mode

Shows the START UP MODE of the device.

 IP Address

Shows the IP address that is specified for the device.

 Port No.

Shows the communication port number of the device.

 Firmware

Shows the main firmware version of the device.

② [Set IP Address] button

When you click this button, the “IP Address” dialog box will appear.

③ [Properties] button

When you click this button, the “Properties” dialog box will appear.

④ [OK] button

Closes the dialog box.

R Remote Version 5.8 User’s Guide 30

“IP Address” dialog box

This appears when you click the [Set IP Address] button in the "Device Information" dialog box.

Here you can view the device's IP Select Mode status, or specify the IP address for a Static IP (Manual) device.

For the RMio64-D, IP Select Mode is set in this dialog box instead of the DIP switch. This setting is available in

firmware V4.10 or later.

If you want to use a device (excluding RMio64-D) in Static IP (Manual) mode, perform the following steps.

1. Start up the device in a mode other than Static IP (Manual).

2. Start R Remote.

3. In the "Device Information" dialog box, select the device that you will be setting to Static IP

(Manual).

4. In the "IP Address" dialog box, enter the necessary information for Static IP (Manual).

5. Click the [OK] button.

6. Put the device in Static IP (Manual) mode, and restart.

① IP Select Mode

Shows the IP Select Mode of the device.

② Static IP (Manual)

Specifies the IP address etc. that is used when the device starts with its IP Select Mode set to Static IP

(Manual).

③ [OK] button

Saves the settings and closes the dialog box.

If you want to change to the IP address that is specified here, set the device's DIP switch to Static IP

(Manual), and then restart the device.

④ [Cancel] button

Discards changes and closes the dialog box.

R Remote Version 5.8 User’s Guide 31

“Properties” dialog box

This dialog box appears when you click the [Properties] button in the "Device Information" dialog box.

This displays information about the device that are connected.

① [Information] display area

Shows information about the device. If the device is not connected, no information is shown.

② [OK] button

Close the window.

R Remote Version 5.8 User’s Guide 32

Updating the Firmware

This guide explains how to update the R series (Rio3224-D, Rio1608-D, Ri8-D, Ro8-D, RSio64-D, RMio64-D,

Rio3224-D2 and Rio1608-D2) and Tio1608-D firmware by using the R Remote (V4.1 or later).

Precautions

 Note that the device may be damaged if you fail to follow these instructions properly, or turn off the device or

disconnect the cable while the update is in progress.

Updating – Operation Overview

Verify that your computer meets the updating requirements of the firmware.

(Page 4)

Connect your computer to the device. (Page 33)

Configure the network settings. (Page 10)

To update the RMio64-D firmware, IPv6 must be enabled on the computer.

Update. (Page 36)

R Remote Version 5.8 User’s Guide 33

Connecting the Computer to the Device

Connect your computer directly to the Dante [PRIMARY] connector of the device to update.

· Dante firmware cannot be updated if the device has been locked with Dante Device Lock. Unlock it from the

Dante Controller. Although device firmware can be updated even if locked with Dante Device Lock, the old

firmware version before updating is displayed on the Dante Controller and the I/O DEVICE screen of the

CL/QL until the device is unlocked.

· When the device to be updated is a domain member of the DANTE DOMAIN MANAGER, unenroll the device

from the DOMAIN, then connect the device and the computer to the same subnet.

This figure is a connection example of the Rio3224-D.

You can perform the update, even when several sets of devices exist on a DANTE Network.

R Remote Version 5.8 User’s Guide 34

Network Settings

When setting up, refer to the description in the “Specify the computer's IP address.”

If the device is controllable from the R Remote, you can perform the update.

For specific instructions and cautions when connecting the devices, refer to the following web site:

https://www.yamahaproaudio.com//

R Remote Firmware Updater

Each device has firmwares for the device and for Dante. Both of firmwares can be updated by the R Remote.

Below are the windows of the R Remote Firmware Updater that appear when updating the firmware.

When the device to be updated is a domain member of the DANTE DOMAIN MANAGER, the device’s Dante

firmware cannot be updated.

When loading firmware including Brooklyn2 and Brooklyn3

① File Path (File selection area)

Select the firmware file to be updated (displayed here).

② Firmware Info (File information area)

Displays information of the selected firmware.

③ Updatable Devices (Device information area)

Displays information about the devices to be updated.

Displays the device label, the firmware version (Model and Dante) and the status. When the device is a

domain member of the DANTE DOMAIN MANAGER, the Dante firmware version is not displayed since

the information cannot be retrieved.

R Remote Version 5.8 User’s Guide 35

The Update Status column displays the following information.

Message

Meaning

Waiting

Waiting for start of update

Updating

Update currently in progress

Cancelled

Update was cancelled.

Finished

Update has finished. The device needs to be restarted.

Completed

Update has finished and been confirmed.

Failed

Update has failed.

The “Progress” column of each firmware displays the following information.

Model: Other than RMio64-D: Erasing  Transferring (and writing)

RMio64-D: Writing

Dante: When loading the device: Brooklyn2/Brooklyn3 (displays the module type)

Updating: Transferring  Writing

NOTICE Do not turn off the device or disconnect the cable while the update is in progress. The device may be damaged if you fail

to follow these instructions properly.

When loading firmware including only Brooklyn2

① [Select] button

Selects the file including the device firmware and the Dante firmware to be updated. The file

“xxxx_v*_**_rrmt.bin” includes the firmwares, the firmware for the device, and the firmware for Dante.

xxxx represents the product name and *_** represents the firmware version number.

(E.g. rio3224-d_v4_10_rrmt.bin)

The [Select] button is occasionally grayed-out and you cannot select the firmware. This may happen when

a network interface for Dante is not configured correctly. In this case, from Dante Controller, select your

network interface in the Configure Dante Interfaces dialog, and make sure that the devices are shown in

Dante Controller.

R Remote Version 5.8 User’s Guide 36

② Checkbox

Selects the device firmware (Model) and/or the Dante firmware with each device to be updated.

For devices with a Dante module that are displayed as Not Available in Dante firmware in the Firmware

Info (file information area), the check boxes are grayed out because the model firmware cannot be

updated.

③ [Update] button

Starts the update process.

In Rio3224-D2 and Rio1608-D2, the change correspondence of the board is implemented by V1.80 or later

of the main body firmware (Model). Therefore, if the version is V1.80 or later, it may not be possible to

downgrade to a lower version., and under that condition, the check box cannot be selected. In that case,

after pressing the [Update] button, a message will be displayed stating that the downgrade cannot be

performed.

④ [Cancel] button

Stops the update operation of the device that has not been updated yet.

Update operation

This section describes how to update the firmware.

1. Start R Remote. Choose “Tool”  “Firmware Update” from the menu of R Remote.

2. (In the case of RMio64-D) Quit the NUAGE Workgroup Manager it it is running.

3. Press the “Select” button and select the firmware “xxxx_v*_**_rrmt.bin” to be updated.

Devices that can be updated appear in the device information area.

Firmware files can be downloaded from the following website:

https://www.yamahaproaudio.com/

xxxx represents the product name and *_** represents the firmware version number.

(E.g. rio3224-d_v4_10_rrmt.bin)

When you select an old firmware which is not supported by R Remote, “invalid file” appears and

the update cannot be started.

If the firmware of the device is an older version than the firmware file, the checkbox for its device

will be automatically checked.

If the firmware of the device is a newer version or a same version, you will need to check the

checkbox of the firmware to update manually.

When the firmware to be updated is selected, the “RRMT_****” folder is temporarily generated

under your user folder of the computer. Do not move or delete this folder and its contents since

these folders and files are used for updating. These folders and files are automatically deleted

when you close the “R Remote Firmware Updater.”

4. Press the “Update” button to start the update.

5. When the update is complete, a popup window appears. Press the "OK" button.

6. To enable the new firmware, turn the updated device off and then on again.

If updated correctly, “Update Status” on the R Remote Firmware Updater will change from “Finished” to

“Completed.”

R Remote Version 5.8 User’s Guide 37

Detecting the device

If you select the firmware file, all detected devices on the network that correspond to the file are displayed on

the Device information area. Also, until the update is actually started, new detected devices corresponding to

the file are added to the list as needed. Conversely, when a device is missing or disconnected due to the cable

having been unplugged or some other reason, a “disconnected” indication is shown on the Firmware Version

column of the device.

In case of failure in updating the firmware

Even if the update has failed, you can update the firmware again after R Remote detects the device. However,

when a device is turned off while the update is in progress, the device cannot be started up, and it will not be

shown on the Device information area of the R Remote, making it necessary to take the following actions for

each problem.

When the device name is shown in red on the network grid view of the Dante Controller

 Dante firmware has entered failsafe mode. Restore the Dante firmware and import and update the

latest Dante firmware using Dante Updater that comes with the Dante Controller.

You can get the Dante firmware from the firmware of R series or Tio1608-D.

Open the R Remote and perform steps 1 through 3 of the “Update operation” (first time only).

The “RRMT_****” folder is generated below your User folder of the computer.

Do not close the R Remote Firmware Update window until updating by Dante firmware

import is complete.

For detailed procedures, please refer to "Fail-Safe Mode" and "Updating the firmware" in the Dante Firmware

Update Guide.

When the device’s red indicators light or flash

 The firmware of the device is damaged. Use R Remote Recovery Updater to update the firmware.

Details on updating are as given below.

The RMio64-D is not supported by the R Remote Recovery Updater. For more information,

contact qualified Yamaha service personnel.

1. Turn off the power to the device.

2. (For devices excepting the Rio3224-D2 and Rio1608-D2) Take note of the DIP switch settings of the

device.

Follow the instructions in step 5 to change DIP switch settings. Take note of the original DIP switch

settings in order to restore the settings after the update has been completed.

3. Disconnect the Ethernet cable from the Dante [PRIMARY] connector and [SECONDARY] connector

on the rear panel of the device.

4. Connect the Dante [PRIMARY] connector on the rear panel of the device to the Ethernet connector

on the computer using an Ethernet cable.

5. For the Rio3224-D2 and Rio1608-D2, turn the device on while simultaneously hold down the 

(INC) button and the encoder.

In except for Rio3224-D2 and Rio1608-D2, set the DIP switch 8 down (ON), the other switches up

(OFF), and then turn the device on.

The device starts in Update mode. The device in Update mode shows:

Rio3224-D, Rio1608-D,

Ri8-D, Rio3224-D2,

All the +48V indicators starts flashing.

R Remote Version 5.8 User’s Guide 38

Rio1608-D, Ri8-D2

Ro8-D

The right red [SYSTEM] indicator and the right orange [SYNC] indicator start flashing.

RSio64-D

All the red indicators of SLOT and WORD CLOCK, and the right red indicator of

SYSTEM and the right orange indicator of SYNC light up.

Tio1608-D

The STATUS INPUT/OUTPUT indicators start flashing.

6. Set your computer’s IP address and subnet mask.

For details on settings, refer to the instructions in “Specify the computer's IP address on page 10.”

IP address: 192.168.0.101

Subnet mask: 255.255.255.0

7. Start the R Remote Recovery Updater.

Within Windows, the “User Account Control” dialog box may appear. Click [Continue] or [Yes].

8. Press the “select” button and select the firmware “xxxx_v*_**_rrmt.bin” to be updated.

xxxx represents the product name and *_** represents the firmware version number.

(E.g. rio3224-d_v4_10_rrmt.bin)

When you select an old firmware file which is not supported by R Remote, an “invalid file”

message appears and you cannot update the firmware. In this situation, use the exclusive update

software for each product which is compressed with the old firmware. For details on updating,

refer to the update guide for the exclusive update software for each product.

9. Press the “connect” button.

The device name and the firmware version are displayed in the “Connect and Update” column.

10. Press the “update” button to start the update.

“Updating firmware….” appears while updating.

11. After the update is complete, close the R Remote Recovery Updater.

When the update is complete, “Update was completed. Close this Update Program.” appears.

12. Turn off the power to the device.

13. (For devices excepting the Rio3224-D2 and Rio1608-D2) Restore the DIP switches to their

original settings.

R Remote Version 5.8 User’s Guide 39

Messages

The following error, warning, and confirmation messages may be displayed on the popup window. Please

follow the instructions.

■ Error messages

Message

Possible cause

Action

Cannot unpack the file.

File path may be too long

Make sure that the file path is less than 260

characters

Failed the temporary unpacking of the

firmware file. File path may be too long.

Make sure that the file path is less than 260

characters.

Cannot unpack the file.

User directory cannot be edited.

Make sure that edits to this directory are

permitted.

Failed the temporary unpacking of the

firmware file. User directory cannot be

edited.

Make sure that edits to this directory are

permitted.

Invalid file.

Select a valid file.

Invalid file or unsupported file was selected.

The firmware file for R Remote contains the

device firmware and the Dante firmware,

unlike in previous files before R Remote was

supported.

Select a valid firmware file. You can find "-

rrmt" in a file name of the firmware file

supported by R Remote.

Unexpected error occurred.

Please restart the R Remote software and try

again.

Unexpected error occurred.

Restart the R Remote software and try again.

Dante Control and Monitoring service not

found.

Make sure that the Dante Controller is

installed and the service is running. Then

restart R Remote software.

Dante Control and Monitoring service is not

running.

Make sure that the Dante Controller is

installed and the service is running. Then

restart R Remote software.

Firmware update failed for device(s).

Check network connection and try again.

Firmware update failed for device(s).

· Check the network settings (page 10) and

network connection (page 33), and then try

again.

· If the device has been locked with Dante

Device Lock, unlock it from the Dante

Controller, and then try again.

· If the device is connected to your computer

via a network, connect your computer

directly to the Dante [PRIMARY] connector

of the device, and then try again.

Dante Network Setting Failed

Network settings for Dante Firmware Update

has failed.

Change the Dante network settings using the

Dante Controller. Refer to "Dante Controller

User’s Guide" for details.

■ Warning Messages

Message

Cause and action

Update in progress.

Wait until update is completed

The Close button [X] was pressed during the update. Wait until update is completed.

■ Confirmation Messages

Message

Cause and action

Cancel update?

This will cancel the update of all waiting

devices.

The [Cancel] button was pressed during the update. Press the [Yes (Y)] button to cancel

the update or press the [No (N)] button to continue the update.

Close?

One or more devices have not been updated

yet.

The Close button [X] was pressed while one or more devices which failed the update

exists. Press the [Yes (Y)] button to quit the R Remote or press the [No (N)] button to

continue the update.

Select file?

One or more devices have not been updated

yet.

The [Select] button was pressed while one or more devices which failed the update exists.

Press the [Yes (Y)] button to select a firmware file or press the [No (N)] button to cancel the

selection.

R Remote Version 5.8 User’s Guide 40

■ Other Messages

Message

New updatable device found.

Firmware update successfully completed.

R Remote Version 5.8 User’s Guide 41

Troubleshooting

Problem

Possible cause

Action

The device is not connected.

The device’s power switch is not on.

Turn the power switch on.

The device’s DIP switch settings are

incorrect.

Refer to "Set on the devices," and make

the appropriate settings.

The UNIT ID of the device is set to

something other than 1 through 24.

Specify a UNIT ID in the range from

decimal 1 to 24 (hexadecimal 1 to 18).

For more about these numbers, refer to

"Decimal/hexadecimal conversion table."

The cables are not connected properly.

If the orange [SYNC] indicator is blinking,

the cable is either broken or not

connected correctly. Connect the cable

correctly.

If you're using REDUNDANT mode,

connect to the network switch that is

connected to the [PRIMARY] connector.

The computer's IP address setting is

incorrect.

Set the computer's IP address to match

the device's DIP switch setting.

Network card selection is incorrect.

In the “Network Setup” dialog box, select

the network card that communicates with

the device.

Firmware is old.

Update the firmware to the version

supported by R Remote using exclusive

update software for each product. For

information about the firmware version

which is supported by R Remote, refer to

"System Requirements."

The R series unit is in AD8HR mode.

Set DIP switches 5 and 6 in the upward

position to select NATIVE mode.

The device is connected to a different

subnet from the computer due to DANTE

DOMAIN MANAGER, etc.

Connect the device and the computer to

the same subnet.

Audio is not input / Input level is

low.

HA gain is not at an appropriate level.

Set the HA gain to an appropriate level.

The external device is not outputting a

signal.

Output a signal from the source device

and make sure that the SIG indicators on

the appropriate channels will light.

Phantom power is not being supplied even

though a condenser microphone is

connected. Turn the [+48V MASTER] switch

on.

Turn phantom power on for the

corresponding channel.

REFRESH mode is selected with the CL/QL

series not connected.

Select RESUME mode.

Adjusting the HA gain does not

change the audio level.

Gain compensation is on.

If you don’t need gain compensation, turn

gain compensation off.

[UNIT ID] rotary switch and DIP

switch settings are not applied.

The settings were changed while the power

was on.

Turn off the power before changing the

settings.

The device is not recognized.

Communication is blocked by the Windows

firewall.

Perform the following procedure so that R

Remote is not blocked by the Windows

firewall.

1. Open Control Panel.

2. In the upper right, set "View by" to

[Category].

3. Click [System and Security].

4. Click [Allow an app through Windows

Firewall].

5. In "Allowed apps and features," select

the checkbox for "Yamaha R Remote"

and also select the checkbox at the

right.

6. Click the [OK] button to close Control

Panel.

R Remote Version 5.8 User’s Guide 42

Problem

Possible cause

Action

The device is unexpectedly

disconnected.

(Mac) App Nap is not disabled.

Select the [Prevent App Nap] checkbox.

The computer has entered sleep mode.

Set the computer so that it does not enter

sleep mode.

The device to be updated is not

displayed.

The Ethernet cable is not properly

connected.

Directly connect the computer to the

Dante PRIMARY connector of the device

using an Ethernet cable. When you want

to update the firmware via a network,

check the connection between the

devices to be updated and the computer

to which the R Remote is installed via a

network (page 33).

The network settings are not correct.

Make the network settings according to

the instructions in the “Specify the

computer's IP address.” For the RMio64-

D, enable the IPv6 on the computer which

is used to operate the R Remote.

The firmware file for updating is not

selected.

Select the firmware file for updating (page

36).

The UNIT ID of the device is not set to a

valid number (1 to 24).

Make sure that each device on the same

network is assigned to a unique UNIT ID.

Specify a UNIT ID in the range from

decimal 1 to 24 (hexadecimal 1 to 18).

For more about these numbers, refer to

"Decimal/hexadecimal conversion table."

The DIP switches of the device are not set

up correctly.

Refer to the “Set on the devices.” For

devices other than the RMio64-D, turn the

device on with DIP switches 7 and 8 up

when you update the device. Make sure

to change the DIP switches’ settings only

after the device's power has been turned

off.

The network card that communicates with

the device is not selected on the computer

to which the R Remote is installed.

Select a network card for communication

with the device from the “Network Setup”

dialog box.

Communication is blocked by the Windows

firewall.

Perform the following procedure so that R

Remote is not blocked by the Windows

firewall.

1. Open Control Panel.

2. In the upper right, set "View by" to

[Category].

3. Click [System and Security].

4. Click [Allow an app through Windows

Firewall].

5. In "Allowed apps and features," select

the checkbox for "Yamaha R Remote"

and also select the checkbox at the

right.

6. Click the [OK] button to close Control

Panel.

The device is connected to a different

subnet from the computer due to DANTE

DOMAIN MANAGER, etc.

Connect the device and the computer to

the same subnet.

Update failed.

The device to be updated is locked by Dante

Device Lock.

Unlock the Dante Device Lock of the

device.

---

Refer to “Messages” to solve the

problem.

The [Select] button is

occasionally grayed-out and

you cannot select the

firmware.

A network interface for Dante is not

configured correctly.

Select your network interface in the

Configure Dante Interfaces dialog from

Dante Controller,, and make sure that the

devices are shown in Dante Controller.

Decimal/hexadecimal conversion table

R Remote only uses values in the range of decimal 1 to 24.

R Remote Version 5.8 User’s Guide 43

Decimal

Hexa-

decimal

Decimal

Hexa-

decimal

Decimal

Hexa-

decimal

Decimal

Hexa-

decimal

Published 04/2023 YJMK- A1

Yamaha V5 Gebruikershandleiding

Merk: Yamaha

Model: V5

Type: Gebruikershandleiding

Download PDF

rapport

in andere talen

italiano: Yamaha V5 Guida utente
русский: Yamaha V5 Руководство пользователя
français: Yamaha V5 Mode d'emploi
español: Yamaha V5 Guía del usuario
Deutsch: Yamaha V5 Benutzerhandbuch
português: Yamaha V5 Guia de usuario
dansk: Yamaha V5 Brugervejledning
suomi: Yamaha V5 Käyttöohjeet
čeština: Yamaha V5 Uživatelská příručka
日本語: Yamaha V5 ユーザーガイド
svenska: Yamaha V5 Användarguide
polski: Yamaha V5 instrukcja
română: Yamaha V5 Manualul utilizatorului

Yamaha V5 Gebruikershandleiding

Yamaha V5 Gebruikershandleiding

in andere talen

Gerelateerde artikelen