Yamaha CVP-605 de handleiding

Categorie
Synthesizer
Type
de handleiding

Deze handleiding is ook geschikt voor

CVP
-
609 / CVP-605
Owner’s Manual
Mode d’emploi
Manual de instrucciones
ESPAÑOL
FRANÇAIS
ENGLISH
IMPORTANT
— Check your power supply —
Make sure that your local AC mains voltage matches the voltage specified on the name plate on the bottom panel. In
some areas a voltage selector may be provided on the bottom panel of the main keyboard unit near the power cord.
Make sure that the voltage selector is set for the voltage in your area. The voltage selector is set at 240V when the unit
is initially shipped. To change the setting use a “minus” screwdriver to rotate the selector dial so that the correct
voltage appears next to the pointer on the panel.
Before using the instrument, be sure to read “PRECAUTIONS” on pages 6-7.
For information on assembling the instrument, refer to the instructions at the end of this manual.
IMPORTANT
– Vérifiez votre alimentation électrique –
Vérifiez que la tension de votre alimentation secteur correspond à celle qui est spécifiée sur la plaque du fabricant,
située sur le panneau inférieur. Dans certaines régions, un sélecteur de tension peut être installé sur le panneau
inférieur du clavier principal, à proximité du cordon d’alimentation. Assurez-vous que le sélecteur de tension est réglé
sur la tension utilisée dans votre région. En usine, le sélecteur est initialement paramétré sur 240 V. Pour modifier ce
réglage, utilisez un tournevis plat et faites tourner le cadran du sélecteur jusqu'à ce que la valeur souhaitée
apparaisse à côté de l’indicateur sur le panneau.
Avant dutiliser l’instrument, lisez attentivement la section « PRÉCAUTIONS D'USAGE » aux pages 6 et 7.
Pour plus d’informations sur lassemblage de l’instrument, reportez-vous aux instructions figurant à la fin de
ce manuel.
IMPORTANTE
compruebe la fuente de alimentación
Asegúrese de que la tensión de la red local de suministro de CA coincide con la especificada en la placa situada en
el panel inferior. Es posible que en algunas zonas se incluya un selector de tensión en el panel inferior de la unidad
del teclado principal, junto al cable de alimentación. Asegúrese de que este selector está ajustado según la tensión
de la zona. El selector de tensión viene ajustado de fábrica en 240 V. Para cambiar el ajuste, utilice un destornillador
de punta plana para girar el selector hasta aparezca que la tensión correcta al lado del puntero del panel.
Antes de utilizar el instrumento, lea las “PRECAUCIONES”, en las páginas 6-7.
Para obtener más información sobre el montaje del instrumento, consulte las instrucciones que encontrará
al final de este manual.
EN FR ES
SPECIAL MESSAGE SECTION
PRODUCT SAFETY MARKINGS:
Yamaha el e c t ronic
products may have either labels similar to the graphics
shown below or molded/stamped facsimiles of these
graphics on the enclosure. The explanation of these
graphics appears on this page. Please observe all
cautions indicated on this page and those indicated in
the safety instruction section.
See bottom of Keyboard enclosure for graphic symbol markings.
The exclamation point within the
equilateral triangle is intended to
alert the user to the presence of
important operating and maintenance
(servicing) instructions in the
literature accompanying the product.
The lightning flash with arrowhead
symbol, within the equilateral
triangle, is intended to alert the user
to the presence of uninsulated
“dangerous voltage” within the
product’s enclosure that may be of
sufficient magnitude to constitute a
risk of electrical shock.
IMPORTANT NOTICE: All Yamaha electronic
products are tested and approved by an independent
safety testing laboratory in order that you may be sure
that when it is properly installed and used in its normal
and customary manner, all foreseeable risks have been
eliminated. DO NOT modify this unit or commission
others to do so unless specifically authorized by
Yamaha. Product performance and/or safety standards
may be diminished. Claims filed under the expressed
warranty may be denied if the unit is/has been modified.
Implied warranties may also be affected.
SPECIFICATIONS SUBJECT TO CHANGE: The
information contained in this manual is believed to be
correct at the time of printing. However, Yamaha
reserves the right to change or modify any of the
specifications without notice or obligation to update
existing units.
ENVIRONMENTAL ISSUES: Yamaha strives to
produce products that are both user safe and
environmentally friendly. We sincerely believe that our
products and the production methods used to produce
them, meet these goals. In keeping with both the letter
and the spirit of the law, we want you to be aware of the
following:
Battery Notice: This product MAY contain a small
non-rechargeable battery which (if applicable) is
soldered in place. The average life span of this type of
battery is approximately five years. When replacement
becomes necessary, contact a qualified service
representative to perform the replacement.
Warning: Do not attempt to recharge, disassemble, or
incinerate this type of battery. Keep all batteries away
from children. Dispose of used batteries promptly and
as regulated by applicable laws. Note: In some areas,
the servicer is required by law to return the defective
parts. However, you do have the option of having the
servicer dispose of these parts for you.
Disposal Notice: Should this product become damaged
beyond repair, or for some reason its useful life is
considered to be at an end, please observe all local,
state, and federal regulations that relate to the disposal
of products that contain lead, batteries, plastics, etc.
NOTICE: Service charges incurred due to lack of
knowledge relating to how a function or effect works
(when the unit is operating as designed) are not covered
by the manufacturers warranty, and are therefore the
owners responsibility. Please study this manual
carefully and consult your dealer before requesting
service.
NAME PLATE LOCATION: The graphic below
indicates the location of the name plate. The model
number, serial number, power requirements, etc., are
located on this plate. You should record the model
number, serial number, and the date of purchase in the
spaces provided below and retain this manual as a
permanent record of your purchase.
Model
Serial No.
Purchase
Date
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
92-469- 1 (bottom)
IMPORTANT SAFETY INSTRUCTIONS
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in
accordance with the manufacturers instructions.
8 Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9 Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10 Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
11 Only use attachments/accessories specified by the
manufacturer.
12 Use only with the cart, stand,
tripod, bracket, or table specified
by the manufacturer, or sold with
the apparatus. When a cart is
used, use caution when moving
the cart/apparatus combination to
avoid injury from tip-over.
13 Unplug this apparatus during
lightning storms or when unused
for long periods of time.
14 Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate
normally, or has been dropped.
(UL60065_03)
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions
contained in this manual, meets FCC requirements. Modifica-
tions not expressly approved by Yamaha may void your author-
ity, granted by the FCC, to use the product.
2. IMPORTANT: When connecting this product to accessories
and/or another product use only high quality shielded cables.
Cable/s supplied with this product MUST be used. Follow all
installation instructions. Failure to follow instructions could void
your FCC authorization to use this product in the USA.
3. NOTE: This product has been tested and found to comply with
the requirements listed in FCC Regulations, Part 15 for Class
“B” digital devices. Compliance with these requirements pro-
vides a reasonable level of assurance that your use of this
product in a residential environment will not result in harmful
interference with other electronic devices. This equipment gen-
erates/uses radio frequencies and, if not installed and used
according to the instructions found in the users manual, may
cause interference harmful to the operation of other electronic
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)
devices. Compliance with FCC regulations does not guarantee
that interference will not occur in all installations. If this product
is found to be the source of interference, which can be deter-
mined by turning the unit “OFF” and “ON”, please try to eliminate
the problem by using one of the following measures:
Relocate either this product or the device that is being affected
by the interference.
Utilize power outlets that are on different branch (circuit breaker
or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead, change
the lead-in to co-axial type cable.
If these corrective measures do not produce satisfactory results,
please contact the local retailer authorized to distribute this type
of product. If you can not locate the appropriate retailer, please
contact Yamaha Corporation of America, Electronic Service
Division, 6600 Orangethorpe Ave, Buena Park, CA90620
The above statements apply ONLY to those products distributed
by Yamaha Corporation of America or its subsidiaries.
FCC INFORMATION (U.S.A.)
* This applies only to products distributed by
YAMAHA CORPORATION OF AMERICA.
COMPLIANCE INFORMATION STATEMENT
(DECLARATION OF
CONFORMITY PROCEDURE)
Responsible Party : Yamaha Corporation of America
Address : 6600 Orangethorpe Ave., Buena Park,
Calif. 90620
Telephone : 714-522-9011
Type of Equipment : Digital Piano
Model Name : CVP-609GP/CVP-609/CVP-605
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received including
interference that may cause undesired operation.
See user manual instructions if interference to radio reception
is suspected.
(FCC DoC)
IMPORTANT NOTICE
FOR THE UNITED KINGDOM
Connecting the Plug and Cord
IMPORTANT. The wires in this mains lead are coloured in
accordance with the following code:
BLUE : NEUTRAL
BROWN : LIVE
As the colours of the wires in the mains lead of this apparatus
may not correspond with the coloured makings identifying the
terminals in your plug proceed as follows:
The wire which is coloured BLUE must be connected to the ter-
minal which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the
terminal which is marked with the letter L or coloured RED.
Making sure that neither core is connected to the earth terminal
of the three pin plug.
(2 wires)
CVP-609/605 Owner’s Manual
4
Contents
About the Manuals................................................................................. 5
Included Accessories ............................................................................. 5
PRECAUTIONS ....................................................................... 6
Notices and Information ....................................................................... 8
Compatible formats for this instrument .............................................. 9
Welcome to the World of CVP
— and the New Touch Screen! 10
Panel Controls 12
Starting Up 14
Turning On/Off the Power .................................................................. 14
Making the Basic Settings.................................................................... 16
Using the Music Rest ........................................................................... 17
Opening/Closing the Lid (CVP-609 Grand Piano type).................... 18
Using Headphones............................................................................... 19
Display Structure 20
Basic Operations 22
Display Configuration ......................................................................... 22
Closing the Current Display................................................................ 24
Display-based Controls........................................................................ 25
Calling up the Desired Functions from the Home Display............... 27
Using the ASSIGNABLE Buttons........................................................ 28
File Management.................................................................................. 29
Entering Characters ............................................................................. 33
Using the Pedals................................................................................... 35
Using the Metronome.......................................................................... 36
Adjusting the Tempo ........................................................................... 36
Setting the Touch Sensitivity of the Keyboard................................... 37
Transposing the Pitch in Semitones................................................... 38
Adjusting the Volume Balance............................................................ 38
Restoring the Factory-programmed Settings .................................... 39
Data Backup.......................................................................................... 39
Piano Room – Enjoying the Piano Performance – 40
Playing the Piano Performance........................................................... 40
Making the Desired Setup in the Piano Room................................... 40
Voices – Playing the keyboard – 42
Playing Preset Voices........................................................................... 42
Setting the Split Point .......................................................................... 45
Playing Super Articulation Voices...................................................... 46
Creating Original Organ Flutes Voices............................................... 47
Styles – Playing Rhythm and Accompaniment – 48
Playing with a Style.............................................................................. 48
Style Control Operations .....................................................................50
Calling up Panel Settings Appropriate for the Current Style
(One Touch Setting)............................................................................. 52
Searching for Suitable Songs for the Current Style ...........................53
Calling up Optimum Styles for Your Performance
(Style Recommender) .......................................................................... 54
Changing the Chord Fingering Type .................................................. 55
Song Playback – Playing and Practice Songs 57
Playback of Songs................................................................................. 57
Displaying Music Notation (Score) .................................................... 60
Displaying Lyrics.................................................................................. 61
Displaying Text.....................................................................................62
One-handed Practice with the Guide Function..................................63
Repeat Playback....................................................................................64
Adjusting the Pitch in Semitones (Pitch Shift) ..................................65
Adjusting the Playback Speed (Time Stretch)....................................65
Canceling the Vocal Part (Vocal Cancel)............................................65
Song Recording – Recording Your Performance – 66
Basic Procedure for Recording (MIDI/Audio Recording) ................66
Recording to Specified Channels (MIDI Recording) .........................68
Converting a MIDI Song to an Audio Song........................................70
Microphone
– Adding Vocal Harmony Effects to Your Singing – 71
Connecting a Microphone ...................................................................71
Applying Vocal Harmony Effects to Your Voice ...............................72
Music Finder
– Calling up Ideal Panel Setups for Your Performance – 74
Selecting the Desired Record (Panel Settings) ...................................75
Searching for Records (Panel Settings)...............................................76
Registering a Song or Style to a Record ..............................................77
Registration Memory
– Saving and Recalling Custom Panel Setups – 78
Registering Your Panel Setups ............................................................78
Saving the Registration Memory as a Bank File.................................79
Recalling a Registered Panel Setup......................................................80
Mixer – Editing the Volume and Tonal Balance – 81
Basic Procedure for the Mixer.............................................................81
Turning Each Channel of the Style or Song On/Off...........................83
Connections
– Using Your Instrument with Other Devices – 84
I/O Connectors......................................................................................84
Connecting Audio Devices
([AUX IN] jack, AUX OUT [L/L+R]/[R] jacks) .................................85
Connecting an External Monitor
([VIDEO OUT] jack, [RGB OUT] terminal).......................................86
Connecting a Footswitch/Foot Controller ([AUX PEDAL] jack) .....87
Connecting a Microphone or Guitar ([MIC./LINE IN] jack)............87
Connecting USB Devices ([USB TO DEVICE] terminal) ..................88
Connecting to an iPhone/iPad ([USB TO DEVICE] terminal,
[USB TO HOST] terminal and MIDI terminals)................................89
Connecting to a Computer ([USB TO HOST] terminal) ...................90
Connecting External MIDI Devices (MIDI terminals) ......................90
Menu Display Function List 91
CVP-609 (Grand piano type) Assembly 93
CVP-609 Assembly 96
CVP-605 Assembly 99
Troubleshooting 102
Specifications 106
Index 109
CVP-609/605 Owner’s Manual
5
About the Manuals
This instrument has the following documents and instructional materials.
Included Documents
Owner’s Manual (this book)
Explains the basic operations of the Clavinova.
Data List
Contains various important preset content lists such as Voices, Styles, etc.
Online Materials (Downloadable from the web)
Reference Manual (only in English, French, German and Spanish)
Explains advanced functions and settings which can be operated from the Menu display (page 24).
iPhone/iPad Connection Manual
Explains how to connect the instrument to smart devices, such iPhone, iPad, etc.
Computer-related Operations
Includes instructions on connecting this instrument to a computer, and operations related to transferring song
data.
MIDI Reference
Contains the MIDI Data Format and MIDI Implementation chart.
To obtain these manuals, access the Yamaha Manual Library, enter the model name (such as “CVP-609”) to the Model
Name box, then click [SEARCH].
Unless indicated otherwise, the illustrations and displays as shown in this manual are based on the CVP-609 (in English). These are
for instructional purposes only, and may appear somewhat different from those on your instrument.
iPhone and iPad are trademarks of Apple Inc., registered in the U.S. and other countries.
The company names and product names in this manual are the trademarks or registered trademarks of their respective companies.
Included Accessories
Owner’s Manual (this book)
Data List
“50 Greats for the Piano” Music Book
Song files (MIDI files) corresponding to the Music Book are available for free downloading over the Internet. To
download the Song files, complete the Yamaha Online Member registration and Product registration at the
following website.
https://member.yamaha.com/myproduct/regist/
Online Member Product Registration
You will need the PRODUCT ID on the sheet in order to fill out the User Registration form.
AC Power Cord
The following items may be included or optional, depending on your locale:
Bench
USB Wireless LAN Adaptor
Yamaha Manual Library http://www.yamaha.co.jp/manual/
CVP-609/605 Owner’s Manual
6
PRECAUTIONS
PLEASE READ CAREFULLY BEFORE PROCEEDING
Please keep this manual in a safe and handy place for future reference.
WARNING
Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical
shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the
following:
Do not place the power cord near heat sources such as heaters or radiators. Also,
do not excessively bend or otherwise damage the cord, or place heavy objects on
it.
Only use the voltage specified as correct for the instrument. The required voltage
is printed on the name plate of the instrument.
Use only the supplied power cord/plug.
Check the electric plug periodically and remove any dirt or dust which may have
accumulated on it.
This instrument contains no user-serviceable parts. Do not open the instrument
or attempt to disassemble or modify the internal components in any way. If it
should appear to be malfunctioning, discontinue use immediately and have it
inspected by qualified Yamaha service personnel.
Do not expose the instrument to rain, use it near water or in damp or wet
conditions, place on it any containers (such as vases, bottles or glasses)
containing liquids which might spill into any openings. If any liquid such as
water seeps into the instrument, turn off the power immediately and unplug the
power cord from the AC outlet. Then have the instrument inspected by qualified
Yamaha service personnel.
Never insert or remove an electric plug with wet hands.
Do not put burning items, such as candles, on the unit. A burning item may fall
over and cause a fire.
When one of the following problems occur, immediately turn off the power switch
and disconnect the electric plug from the outlet. Then have the device inspected
by Yamaha service personnel.
- The power cord or plug becomes frayed or damaged.
- It emits unusual smells or smoke.
- Some object has been dropped into the instrument.
- There is a sudden loss of sound during use of the instrument.
Power supply/Power cord
Do not open
Water warning
Fire warning
If you notice any abnormality
DMI-5 1/2
CVP-609/605 Owner’s Manual
7
CAUTION
Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage
to the instrument or other property. These precautions include, but are not limited to, the following:
Do not connect the instrument to an electrical outlet using a multiple-connector.
Doing so can result in lower sound quality, or possibly cause overheating in the
outlet.
When removing the electric plug from the instrument or an outlet, always hold
the plug itself and not the cord. Pulling by the cord can damage it.
Remove the electric plug from the outlet when the instrument is not to be used for
extended periods of time, or during electrical storms.
Read carefully the attached documentation explaining the assembly process.
Failure to assemble the instrument in the proper sequence might result in
damage to the instrument or even injury.
Do not place the instrument in an unstable position where it might accidentally
fall over.
When transporting or moving the instrument, always use two or more people.
Attempting to lift the instrument by yourself may damage your back, result in
other injury, or cause damage to the instrument itself.
Before moving the instrument, remove all connected cables, to prevent damage
to the cables or injury to anyone who might trip over them.
When setting up the product, make sure that the AC outlet you are using is easily
accessible. If some trouble or malfunction occurs, immediately turn off the power
switch and disconnect the plug from the outlet. Even when the power switch is
turned off, electricity is still flowing to the product at the minimum level. When
you are not using the product for a long time, make sure to unplug the power
cord from the wall AC outlet.
Before connecting the instrument to other electronic components, turn off the
power for all components. Before turning the power on or off for all components,
set all volume levels to minimum.
Be sure to set the volumes of all components at their minimum levels and
gradually raise the volume controls while playing the instrument to set the
desired listening level.
Do not insert a finger or hand in any gaps on the key cover or instrument. Also
take care that the key cover does not pinch your finger.
Never insert or drop paper, metallic, or other objects into the gaps on the key
cover, panel or keyboard. This could cause physical injury to you or others,
damage to the instrument or other property, or operational failure.
Do not rest your weight on, or place heavy objects on the instrument, and do not
use excessive force on the buttons, switches or connectors.
Do not use the instrument/device or headphones for a long period of time at a
high or uncomfortable volume level, since this can cause permanent hearing
loss. If you experience any hearing loss or ringing in the ears, consult a
physician.
Do not place the bench in an unstable position where it might accidentally fall
over.
Do not play carelessly with or stand on the bench. Using it as a tool or stepladder
or for any other purpose might result in accident or injury.
Only one person should sit on the bench at a time, in order to prevent the
possibility of accident or injury.
If the bench screws become loose due to extensive long-term use, tighten them
periodically using the included tool.
Keep special watch over any small children so that they don’t fall off the rear of
the bench. Since the bench does not have a backrest, unsupervised use may
result in accident or injury.
Always turn the power off when the instrument is not in use.
Even when the [ ] (Standby/On) switch is in standby status (power lamp is off), electricity is still flowing to the instrument at the minimum level.
When you are not using the instrument for a long time, make sure you unplug the power cord from the wall AC outlet.
Power supply/Power cord
Assembly
Location
Connections
Handling caution
Using the bench (If included)
Yamaha cannot be held responsible for damage caused by improper use or modifications to the instrument, or data that is lost or destroyed.
DMI-5 2/2
CVP-609/605 Owner’s Manual
8
Notices and Information
NOTICE
To avoid the possibility of malfunction/ damage to the product, damage to data, or damage to other property, follow the
notices below.
Handling
Do not use the instrument in the vicinity of a TV, radio, stereo equipment, mobile phone, or other electric devices. Otherwise, the
instrument, TV, or radio may generate noise. When you use the instrument along with the application on your iPhone/iPad, we
recommend that you set “Airplane Mode” to “ON” on your iPhone/iPad in order to avoid noise caused by communication.
Do not expose the instrument to excessive dust or vibrations, or extreme cold or heat (such as in direct sunlight, near a heater, or in
a car during the day) to prevent the possibility of panel disfiguration, damage to the internal components or unstable operation.
(Verified operating temperature range: 5° – 40°C, or 41° – 104°F.)
Do not place vinyl, plastic or rubber objects on the instrument, since this might discolor the panel or keyboard.
In the case of a model with a polished finish, bumping the surface of the instrument with metal, porcelain, or other hard objects can
cause the finish to crack or peel. Use caution.
Instrument / Bench Maintenance
To keep your Clavinova in optimum condition, we recommend that you periodically follow the maintenance points
below.
When cleaning the instrument or bench, use a soft, dry or slightly damp cloth. Do not use paint thinners, solvents, cleaning fluids,
or chemical-impregnated wiping cloths. Otherwise, it may become discolored or degraded.
If you are using a model with a polished finish, gently remove dust and dirt with a soft cloth. Do not wipe too hard since small
particles of dirt can scratch the instrument's finish. To keep the surface polished, apply commercially available piano polisher to a
soft cloth and wipe the instrument’s surface with it. Then, polish it with a separate cloth. Before using any piano polisher, make sure
to read the instructions for proper usage.
During extreme changes in temperature or humidity, condensation may occur and water may collect on the surface of the
instrument. If water is left, the wooden parts may absorb the water and be damaged. Make sure to wipe any water off immediately
with a soft cloth.
As with an acoustic piano, pedals may become tarnished across the ages. When this occurs, polish the pedal with a compound
designed for piano pedals. Before using the compound, make sure to read the instructions for proper usage.
Saving data
The edited Songs/Styles/Voices and MIDI settings are lost when you turn off the power of the instrument without saving. It occurs
also when the power is turned of by Auto Power Off function (page 15). Save the edited data to the instrument (User memory) or
USB flash memory (page 29). Saving the data to USB flash memory is even more secure, since the data in the instrument may be
lost due to malfunction or incorrect operation.
To further protect against data loss through the USB flash memory damage, we recommend that you save your important data onto
two USB flash memories.
CVP-609/605 Owner’s Manual
9
Information
About copyrights
Copying of the commercially available musical data including but not limited to MIDI data and/or audio data is strictly prohibited
except for your personal use.
This product incorporates and bundles computer programs and contents in which Yamaha owns copyrights or with respect to
which it has license to use others’ copyrights. Such copyrighted materials include, without limitation, all computer software, style
files, MIDI files, WAVE data, musical scores and sound recordings. Any unauthorized use of such programs and contents outside of
personal use is not permitted under relevant laws. Any violation of copyright has legal consequences. DON’T MAKE,
DISTRIBUTE OR USE ILLEGAL COPIES.
About functions/data bundled with the instrument
Yamaha may from time to time update firmware of the product without notice for improvement in functions and usability. To take
full advantage of this instrument, we recommend that you upgrade your instrument to the latest version. The latest firmware can be
downloaded from the website below:
http://download.yamaha.com/
Some of the preset songs have been edited for length or arrangement, and may not be exactly the same as the original.
This device is capable of using various types/formats of music data by optimizing them to the proper format music data for use with
the device in advance. As a result, this device may not play them back precisely as their producers or composers originally intended.
MPEG Layer-3 audio coding technology licensed from Fraunhofer IIS and Thomson.
Supply of this product does not convey a license nor imply any right to distribute content created with this product in revenue-
generating broadcast systems (terrestrial, satellite, cable and/or other distribution channels), streaming applications (via Internet,
intranets and/or other networks), other content distribution systems (pay-audio or audio-on-demand applications and the like) or
on physical media (compact discs, digital versatile discs, semiconductor chips, hard drives, memory cards and the like). An
independent license for such use is required. For details, please visit http://mp3licensing.com.
Tu ni ng
Unlike an acoustic piano, this instrument does not need to be tuned by an expert (although the pitch can be user-adjusted to match
other instruments). This is because the pitch of digital instruments is always maintained perfectly.
Compatible formats for this instrument
GM2
“GM (General MIDI)” is one of the most common Voice allocation formats. “GM System Level 2” is a standard specification that
enhances the original “GM” and improves Song data compatibility. It provides for increased polyphony, greater Voice selection,
expanded Voice parameters, and integrated effect processing.
XG
XG is a major enhancement of the GM System Level 1 format, and was developed by Yamaha specifically to provide more Voices
and variations, as well as greater expressive control over Voices and effects, and to ensure compatibility of data well into the
future.
GS
GS was developed by the Roland Corporation. In the same way as Yamaha XG, GS is a major enhancement of the GM specifically
to provide more Voices and Drum kits and their variations, as well as greater expressive control over Voices and effects.
XF
The Yamaha XF format enhances the SMF (Standard MIDI File) standard with greater functionality and openended
expandability for the future. This instrument is capable of displaying lyrics when an XF file containing lyric data is played.
SFF GE (Guitar Edition)
“SFF (Style File Format)” is an original Style file format by Yamaha which uses a unique conversion system to provide high-
quality automatic accompaniment based on a wide range of chord types. “SFF GE (Guitar Edition)” is an enhanced format of SFF,
which features improved note transposition for guitar tracks.
CVP-609/605 Owner’s Manual
10
Welcome to the World of CVP — and the New Touch Screen!
Welcome to the World of CVP — and the
New Touch Screen!
This new CVP model is equipped with a convenient touch screen, enabling visual and intuitive control over virtually all
instrument functions. Simply by touching this large and easy-to-see display, you can select desired items, enable and
control various features, or edit parameter values — with greater ease and speed than ever before!
The instrument also has many advanced features that enhance your musical enjoyment and expand your creative and
performance possibilities. Let’s take a look…
Weve combined some sophisticated technologies — including the
Real Grand Expression (RGE) Sound Engine and Natural Wood
(NW) keyboard (on the CVP-609), or the Graded Hammer 3 (GH3)
keyboard (on the CVP-605) — to reproduce the natural touch
response and expressive nuances of an actual concert grand piano.
In addition, there is a special “Piano Room” containing all relevant
piano performance settings, which you can call up with a single
button press any time you want. This complete piano ‘environment
lets you select the desired piano type as well as different room
ambiences — providing a total piano experience, as if you were
playing an actual piano.
Page 40
Naturally, the CVP provides many realistic piano Voices for your
playing enjoyment. But it also features a wide variety of authentic
instruments, both acoustic and electronic. Moreover, the special
Super Articulation Voices realistically recreate many of the
performance techniques and characteristic sounds generated when
an artist plays an instrument. The result is superbly detailed
expression — such as the realistic sound of finger slides on guitar,
and the expressive breath noises of saxophone and other wind
instruments.
Page 42
Even if youre playing alone, the CVP can put an entire backing band
behind you! Simply playing chords with your left hand automatically
triggers and controls the auto accompaniment backing (Style
function). You can change arrangements on the fly, instantly
selecting different rhythm variations and breaks in real time —
including Intro, Ending, and Fill-in — during your performance.
And if you find it hard to select just the right Style from the huge
variety available, use the Style Recommender function, which calls
up a list of suggested Styles, based on a sample rhythm you play.
Page 48
True Acoustic Piano Feel
Enormous Variety of Instrument Voices
Full Backing Band Accompaniment
CVP-609/605 Owner’s Manual
11
Welcome to the World of CVP — and the New Touch Screen!
The Lesson features are a fun way to learn and master Songs, with
notation shown on the display. Moreover, each key of the
keyboard has a Guide lamp, which lights to indicate the notes to
be played, letting you practice melodies and phrases smoothly —
even if you are a beginner or have trouble reading notation.
Page 63
Since a microphone can be connected to the Clavinova and Song
lyrics can be shown on the display, you can enjoy singing along
with your keyboard performance or along with Song playback.
You can also cancel the vocal part on audio recordings, letting you
sing along with (or instead of!) your favorite artists and groups,
and enjoy performing even more.
Pages 61, 71
By connecting your iPhone or iPad to the Clavinova and using
applications, you can manage your music files more easily and
take advantage various functions — expanding the potential of the
Clavinova and make it an even more integral part of your total
music life.
Page 89
Enjoyable Song Lesson Features — with Score Display and Guide Lamps
Sing Along with Song Playback or Your Own Performance
Using an iPhone or iPad with the CVP
Want to learn more about the Clavinovas features?
Press the [DEMO] button and start the
demonstration!
In the Demo Menu, you can play special Demo Songs or call up
brief historical information and function explanations of the
Clavinova by touching the display.
CVP-609/605 Owner’s Manual
12
Panel Controls
Panel Controls
[USB TO DEVICE] terminal ............ page 88
For connecting a USB flash memory or USB wireless
LAN adaptor.
[ ] (Standby/On) switch .................. page 14
For turning the power on or setting it to standby.
[MASTER VOLUME] control ........... page 14
For adjusting the overall volume.
[DEMO] button ................................. page 11
For calling up the Demo display.
[MIC] lamp ........................................ page 71
For checking the input level of the microphone.
[METRONOME ON/OFF] button .... page 36
For turning the metronome on or off.
TRANSPOSE buttons ....................... page 38
For transposing the pitch in semitone steps.
[TAP TEMPO]/TEMPO [-]/[+] buttons
............................................................ page 36
For controlling the tempo for Style, MIDI Song and
metronome playback.
STYLE buttons .................................. page 48
For selecting a Style category.
ASSIGNABLE buttons ....................... page 28
For assigning shortcuts to often used functions.
STYLE CONTROL buttons ............... page 50
For controlling Style playback.
LCD (touch screen)............................ page 20
Allows you to select or change the parameters by
simply touching the ‘virtual’ buttons or sliders on
the display.
Data Dial............................................ page 26
For selecting an item or changing the value.
[HOME] button ................................. page 26
For calling up the Home display, or the first display
when the power is turned on.
[PIANO ROOM] button.................... page 40
For instantly calling up the optimum piano-related
settings for playing the instrument simply as a
piano.
SONG CONTROL buttons ................ page 59
For controlling Song playback.
VOICE buttons .................................. page 42
For selecting a keyboard part or a Voice category.
REGISTRATION MEMORY buttons
............................................................ page 78
For registering and recalling panel setups.
ONE TOUCH SETTING buttons...... page 52
For calling up the appropriate panel settings for the
Style.
Drum Kit icons .................................. page 44
These indicate drum instruments assigned to each
key when the “Standard Kit 1” Voice is selected.
A-1 B-1 C0 D0 E0 F0 G0 A0 B0 C1 D1 E1 F1 G1 A1 B1 C2 D2 E2 F2 G2 A2 B2 C3 D3 E3
CVP-609/605 Owner’s Manual
13
Panel Controls
F3 G3 A3 B3 C4 D4 E4 F4 G4 A4 B4 C5 D5 E5 F5 G5 A5 B5 C6 D6 E6 F6 G6 A6 B6 C7
CVP-609
CVP-609
CVP-605
Key cover (page 14)
Guide lamps (page 63)
I/O connectors
(page 84)
Sheet music braces
(page 17)
Music rest (page 17)
Music rest
(page 17)
Sheet music
braces (page 17)
I/O connectors
(page 84)
Key cover
(page 14)
Guide lamps
(page 63)
Pedals
(page 35)
Music rest (page 17)
Sheet music braces (page 17)
I/O connectors
(page 84)
Key cover (page 14)
Guide lamps (page 63)
Pedals (page 35)
Pedals (page 35)
Lid (page 18)
(Grand Piano type)
CVP-609/605 Owner’s Manual
14
Starting Up
Starting Up
1 Connect the power cord.
First insert the plug of the power cord into the AC connector on the instrument,
then plug the other end of the cable into a proper AC outlet on the wall.
2 Lift the key cover slightly, then push it up and back to open.
3 Press the [ ] (Standby/On) switch to turn the power on.
The display located in the center of the front panel and the power indicator located
below the left end of the keyboard lights up.
4 Play the keyboard.
While playing the keyboard, adjust the volume level by using the [MASTER
VOLUME] control.
Turning On/Off the Power
1-1
1-2
The shape of the plug and outlet
differ depending on locale.
Hold the cover with both
hands when opening or
closing it. Do not release it
until it is fully opened or
closed. Be careful to avoid
catching fingers (yours or
others, especially
children’s) between the
cover and the unit.
Do not place anything (such
as metal objects or pieces
of paper) on top of the key
cover. Small objects placed
on the key cover may fall
inside the unit when the
cover is opened and may be
nearly impossible to
remove. Once inside, they
could cause electric shock,
short circuit, fire or other
serious damage to the
instrument.
CAUTION
Be careful to avoid catching your fingers
when opening the cover.
Power indicator
CVP-609/605 Owner’s Manual
15
Starting Up
5 After you use the instrument, press the [ ] (Standby/On) switch to
turn the power off.
The display and power indicator turn off.
During recording, editing and display of certain messages, the power cannot be
turned off even if you press the [ ] switch. If you want to force-quit the
instrument in such a situation, press and hold the [ ] switch for longer than three
seconds.
6 Lower the key cover back in place gently with both hands.
CAUTION
Auto Power Off function
To prevent unnecessary power consumption, this instrument features an Auto Power Off
function that automatically turns the power off if the instrument is not operated for a
specified period of time. The amount of time that elapses before the power is
automatically turned off is approximately 30 minutes by default; however, you can
change the setting (page 16).
CAUTION
Be careful to avoid catching your fingers when
closing the cover.
CVP-609/605 Owner’s Manual
16
Starting Up
As necessary, make the basic settings such as Language shown on the display.
1 Call up the operation display.
First, touch [Menu] at the bottom right corner of the Home display which is shown
when the power is turned on. Then touch [] to move to page 2 (if necessary), and
touch [Utility] and [System] in order.
2 Make the necessary settings by touching the display.
Disabling Auto Power Off (Simple Method)
Turn the power on while holding down the lowest key on the keyboard. An “Auto power
off disabled” message appears briefly and Auto Power Off is disabled.
Making the Basic Settings
Vers ion
Indicates the firmware version of this instrument.
Yamaha may from time to time update firmware of the product
without notice for improvement in functions and usability. To take
full advantage of this instrument, we recommend that you upgrade
your instrument to the latest version. The latest firmware can be
downloaded from the website below:
http://download.yamaha.com/
Copyright
Touch here to call up copyright information.
Language
Determines the language used in the display for messages. Touch
this setting to call up the language list, then select the desired one.
Owner Name
Lets you input your name which appears in the opening display
(called up when the power is turned on). Touch this setting to call
up the character entry window, then input your name (page 33).
Auto Power Off
Lets you set the amount of time that elapses before the power is
turned off by Auto Power Off function (page 15). Touch this to call
up the list of settings, then select the desired one. To disable Auto
Power Off, select “Disabled” here.
+
CVP-609/605 Owner’s Manual
17
Starting Up
Pull the music rest toward yourself as far as it will go. When raised, the music rest locks
in place at a certain angle and cannot be adjusted. The braces allow you to hold the pages
of music books in place.
To lower the music rest, lift the music rest slightly, then turn it back slowly.
Using the Music Rest
When raising or lowering the
music rest, do not release
your hands from the music
rest until it is all the way up or
down.
Sheet music braces
CAUTION
Be careful to avoid catching your fingers.
Close the sheet music braces
CAUTION
CVP-609/605 Owner’s Manual
18
Starting Up
One long stay and one short stay are provided on the lid. Use one of them to hold the lid
open at desired angle.
Opening the Lid
Raise the music rest.
Raise and hold the right side of the lid (viewed from the keyboard end of the
instrument).
Raise the lid stay and carefully lower the lid so that the end of the stay fits into the
recess in the lid.
For the longer stay, use the inner recess, and for the shorter stay, use the outer recess to
support the lid.
Closing the Lid
Hold the lid stay and carefully raise the lid.
Hold the lid in its raised position and lower the lid stay.
Carefully lower the lid.
Opening/Closing the Lid (CVP-609 Grand Piano type)
CAUTION
CAUTION
Longer stay
Shorter stay
CVP-609/605 Owner’s Manual
19
Starting Up
Since this instrument is equipped with two [PHONES] jacks, you can connect two sets
of standard stereo headphones. If you are using only one set of headphones, insert a plug
into either of these jacks.
Using the Headphone Hanger
A headphone hanger is included in the instrument package so that you can hang the
headphones on the instrument. Install the headphone hanger by following the
instructions at the end of this manual.
Using Headphones
Do not use headphones at a
high volume for an extended
period of time; doing so may
cause hearing loss.
MIN MAX
INPUT
MIC.
MIC. LINE PHONES
VOLUME
LINE IN
Standard stereo phone plug
CVP-609/605 Owner’s Manual
20
Display Structure
Display Structure
Turning on this instrument calls up the Home display, from which you can call up the File Selection display and Menu
display giving you convenient access to various functions and allowing you to make various settings. For detailed
instructions on the display, refer to page 22.
File Selection
display
You can call up the desired
type of display by touching
the Style name, Voice name
or Song name on the Home
display.
Home display
This is the portal or home base of the
instruments display structure.
By expanding the Style area,
you can call up the playback-
related controls on the display.
Menu display
By touching each of the icons,
you can call up various functions,
such as Song Score, Volume
Balance and other detailed
settings.
Style Selection display Voice Selection display
CVP-609/605 Owner’s Manual
21
Display Structure
By expanding the Song area,
you can call up the playback-
related controls on the display.
Song Selection display
CVP-609/605 Owner’s Manual
22
Basic Operations
Basic Operations
This section covers the most often used displays: Home, File Selection and Menu. The
Home display appears when the power is turned on. The File Selection display and
Menu display can be called up from the Home display.
Home Display
Appears when the power is turned on, and can be called up when the [HOME] button is
pressed. This display shows the current basic settings such as the current Voice and
Style, allowing you to see them at a single glance. Because of this, you should normally
have the Home display shown when you perform on the keyboard.
Voice area
Indicates the current Voices for each of the keyboard parts (Main, Left and Layer)
and the on/off status of these parts (page 42). Touching a Voice name calls up the
Voice Selection display.
Style area
Indicates the current Style (page 48). Touching a Style name calls up the Style
Selection display. Touch [] at the upper left of this area to expand the area. To reset
the area to the default status, touch [], which appears at the upper right of the
Voice area.
Song area
Indicates the current Song (page 57). Touching a Song name calls up the Song
Selection display. Touch [] at the upper right of this area to expand the area. To
reset the area to the default status, touch [] appears at the upper left of the Voice
area.
Registration area
Indicates the currently selected Registration Memory Bank name, Registration
name and Registration Sequence when it is active (page 78). Touching this area calls
up the Registration Bank Selection display. You can hide or show this area by
touching [] or [] in the area.
Menu area
Contains the shortcut icons which let you call up various functions with a single
touch. Touching a shortcut icon will call up the display of the corresponding
function. Touch [Menu] icon at the right end to call up the Menu display, from
which you can register the desired one to this Menu area (page 27).
Display Configuration
NOTE
NOTE
CVP-609/605 Owner’s Manual
23
Basic Operations
File Selection Display
The File Selection display is for selecting a Voice, Style, Song, and other data. You can
call up this display by touching the name of the Voice, Style or Song on the Home
display, or by pressing one of the VOICE or STYLE buttons, etc.
Category
A wide variety of data such as Voices and Styles are divided into several categories
(tabs) according to the data type. Except for the following two, all tabs are referred to
as “preset” tabs, since they contain preset data.
Sub Category / Folder (Path)
When one of the preset tabs is selected, the sub categories are shown here
according to the data type. For example, various piano types such as Grand Piano
and Electric Piano are shown when you touch the “Piano” tab on the Voice
Selection display.
When the Favorite tab is selected, this is not available.
When the User tab is selected, the current path or folder is shown here according
to the folder structure.
Selectable data (files)
The files that can be selected are shown. If two or more pages are available, you can
call up another page by touching [] or [].
Operation icons
The functions (save, copy, delete, etc.) which can be operated via the File Selection
display are shown. The icons shown here differ depending on which File Selection
display is selected. For detailed instructions, refer to pages 29 – 33, or the
instructions for each functions File Selection display.
(Favorite tab)
Location where the Voices or Styles which you have registered as
Favorites are shown (page 32). This tab is available only for Voices
and Styles.
(User tab)
Location where recorded or edited data is saved. Data saved to the
instrument are shown in “USER” (User memory), while data in the
connected USB flash memory are shown in “USB.” In this manual,
data in the User tab is referred to as “User data.
Path
To the upper folder
NOTE
CVP-609/605 Owner’s Manual
24
Basic Operations
Menu Display
This is the portal display for using various functions and can be called up by touching
the [Menu] icon at the bottom right corner of the Home display.
Functions
Various convenient functions are shown via icons. Touching each of them calls up
the corresponding function. This list consists of two pages, which you can select by
pressing [] or [].
For information on each function, refer to the “Menu Display Function List”
(page 91) or the Reference Manual on the website.
Shortcuts
By registering often used functions here as Shortcuts, you can call up them quickly
from the Home display. For instructions, refer to page 27.
To close the current display, touch [×] at the upper right of the display (or window) or
[Close] at the lower right of the display (or window). When a message (information or
confirmation dialog) appears, touching the appropriate item such as “Yes” or “No” closes
the message.
If you want to quickly return to the Home display press the [HOME] button.
NOTE
NOTE
Instruction conventions for the Menu display
Throughout this manual, instructions with multiple steps are given in convenient shorthand,
with arrows indicating the proper sequence.
Example: [Menu] → [Utility] → [System] → [Language]
The example above describes a three step operation:
1) From the Menu display, touch [Utility].
2) Touch [System].
3) Touch [Language].
Closing the Current Display
CVP-609/605 Owner’s Manual
25
Basic Operations
The display of this instrument is a special touch screen that allows you to select or
change the desired parameter by simply touching the corresponding setting on the
display.
Using the Display (Touch Screen)
To uc h
To select an item, lightly touch the
corresponding indication on the display.
Slide
Hold down the display slider, then slide
your finger vertically or horizontally to
change the parameter value.
Rotate
Touch and hold the display knob, and
rotate your finger around the knob to
change the parameter value.
Touch and hold
This instruction means to touch the
object in the display and hold it for a
while.
When setting values by using []/[], a
slider or a knob, you can restore the
default value by touching and holding
the value on the display.
Display-based Controls
Data dial
[HOME] button
Display
NOTE
NOTE
CVP-609/605 Owner’s Manual
26
Basic Operations
Rotating the Data Dial
Depending on the display, the Data dial can be used in the following two ways.
Adjusting the parameter values
After selecting the desired parameter, use the Data dial to adjust the value. This is useful
if you have difficulty adjusting by touching on the display, or want finer control over the
adjustment.
Selecting an item from a list
In File Selection displays (page 23) and the List windows for setting parameters, use the
Data dial to select an item.
Pressing the [HOME] Button
You can quickly return to the Home display (the display shown when the power is
turned on) by pressing the [HOME] button whenever you want.
Data dial
CVP-609/605 Owner’s Manual
27
Basic Operations
From all the functions shown on the Menu display, you can pick out an often used one
and register it to a shortcut. Registered shortcuts are shown in the Menu area (page 22)
at the bottom of the Home display, allowing you to quickly call up the desired function
from the Home display.
Creating a Shortcut on the Home Display
Although seven shortcuts are registered by default, you can customize them as
necessary.
1 Touch and hold the icon of the desired function until the color of the
shortcut area (bottom of the display) changes.
2 From the seven locations at the bottom of the display, touch the one you
want to replace.
The function selected in step 1 will be registered, replacing the one selected here.
Moving a Shortcut
1 Touch and hold the desired icon until the color changes.
2 From the seven locations, touch the desired destination icon.
The icons touched in steps 1 and 2 are switched.
Deleting a Shortcut
1 Touch and hold the desired icon until the color changes.
2 Touch the same icon again to delete it from the shortcuts.
Calling up the Desired Functions from the Home
Display
1
2
NOTE
12
NOTE
1
NOTE
CVP-609/605 Owner’s Manual
28
Basic Operations
You can assign the functions which you use frequently to these four buttons at the left
side of the display. Also the functions listed on the Menu display can be assigned as
shortcut.
1 Call up the operation display via [Menu] → [Assignable] → [Assignable].
2 Touch the desired button number to call up the list.
3 Select the desired item from the functions and shortcuts (equivalent to
the functions in the Menu display).
Using the ASSIGNABLE Buttons
2
3
NOTE
CVP-609/605 Owner’s Manual
29
Basic Operations
Data you have created such as recorded Song and edited Voice can be saved as files to
the instrument (referred to asUser memory”) and the USB flash memory. If you’ve
saved a lot of files, you may have trouble finding the desired file quickly. To make
operation easier, you can organize your files in folders, rename the files, delete
unnecessary files, etc. These operations are done in the File Selection display.
Saving a File
You can save your original data (such as Songs you’ve recorded and Voices youve
edited) as a file to the instrument or USB flash memory.
1 In the relevant display, touch (Save) to call up the display for
selecting the saving destination.
2 Select the location to which you want to save the file.
To show the next higher level folder, touch .
You can create a new folder by touching (New Folder).
3 Touch [Save here] to call up the Character Entry window.
4 Enter the file name (page 33).
Even if you skip this step, you can rename the file at any time (page 30) after saving.
5 Touch [OK] in the Character Entry window to actually save the file.
The saved file will be automatically located at the appropriate position among the
files in alphabetical order.
File Management
NOTE
3
NOTE
CVP-609/605 Owner’s Manual
30
Basic Operations
Creating a New Folder
Folders can be created, named and organized as desired, making it easier to find and
select your original data.
1 In the File Selection display, touch the User tab (page 23) then select the
location to which you want to create a new folder.
To show the next higher level folder, touch .
2 Touch [File] to call up the File Management icons.
3 Touch (New folder) to call up the Character Entry window.
4 Input the name of the new folder (page 33).
Renaming a File/Folder
You can rename files/folders.
1 Call up the File Selection display, on which the desired file/folder is
shown.
2 Touch [File] to call up the File Management icons.
3 Enter a checkmark to the desired file or folder by touching it.
4 Touch (Rename) to call up the Character Entry window.
5 Input the name of the selected file or folder (page 33).
NOTE
NOTE
2 3
File Management icons
NOTE
NOTE
NOTE
CVP-609/605 Owner’s Manual
31
Basic Operations
Copying or Moving Files
You can copy or cut a file and paste it to another location (folder). You can also copy a
folder (but not move it) by using the same procedure.
1 Call up the File Selection display, on which the desired files/folders are
shown.
2 Touch [File] to call up the File Management icons.
3 Enter checkmarks to the desired files/folders by touching each item.
One or more files/folders can be checked. When you want to enter checkmarks to
all displayed items, touch (Check All). Touch (Check All) again to remove
all the checkmarks.
4 Touch (Copy) or (Move), to call up the display for selecting the
destination.
5 Select the desired destination (path) to paste the files/ folders.
You can create a new folder by touching (New Folder).
6 Touch [CopyHere] or [MoveHere] to paste the files/folders you’ve
selected in step 3.
The pasted file/folder appears on the display at the appropriate position among the
files in alphabetical order.
Deleting Files/Folders
You can delete files/folders.
1 Call up the File Selection display, on which the desired files/folders are
shown.
2 Touch [File] to call up the File Management icons.
3 Enter checkmarks to the desired files/folders by touching each item.
One or more files/folders can be checked. When you want to enter checkmarks to
all displayed items, touch (Check All). Touch (Check All) again to remove
all the checkmarks.
4 Touch (Delete).
5 After the confirmation message appears, touch [Yes] to actually delete
the files/folders you’ve selected in step 3.
To cancel this operation, touch [No] instead of [Yes].
NOTE
NOTE
NOTE
NOTE
NOTE
CVP-609/605 Owner’s Manual
32
Basic Operations
Registering Files to the Favorite Tab
You can call up your favorite or often used Voices or Styles quickly by registering them
to the Favorite tab. Touch the star mark ( ) at the right side of each file to register the
corresponding file to the Favorite tab. To remove the registered file from the Favorite
tab, touch the colored star mark ( ) in the Favorite tab or in the tab which actually
contains the corresponding file.
Sorting the File Order in the Favorite Tab
You can change the order of the files such as Voices and Styles in the Favorite tab.
1 In the Voice Selection display or Style Selection display, touch the
Favorite tab.
2 Touch (Order) to call up the Order Edit display.
3 Touch the file you want to move.
4 Touch the location to which you want to move the file selected in step 3.
5 Repeat steps 3 – 4 as necessary.
6 Touch [Complete] to exit from the Order Edit display.
NOTE
Favorite tab
Registered
Not
registered
4
3
CVP-609/605 Owner’s Manual
33
Basic Operations
This section covers how to enter characters for naming your files/folders, inputting
keywords on Music Finder (page 74), etc. Entering characters should be done in the
display shown below.
1 Touch the character type.
When the Language (page 16) is set to other than Japanese:
When the Language (page 16) is set to Japanese:
Restrictions for protected Songs
Commercially available Song data may be copy protected to prevent illegal copying or
accidental erasure. They are marked by the indications at the left side of the file names. The
indications and relevant restrictions are detailed below.
(gray) Protected 1: Indicates Preset Songs saved to the “USER” (User memory) and
Disklavier Piano Soft Songs. These cannot be copied/moved/saved to external devices.
(yellow) Protected 2 Original: Indicates Yamaha-protection-formatted Songs. These
cannot be copied. These can be moved/saved only to the “USER” (User memory) and USB storage
devices with ID.
(yellow) Protected 2 Edited: Indicates edited “Protected 2 Original” Songs. Make sure to
save these to the same folder containing the corresponding “Protected 2 Original” Song. These
cannot be copied. These can be moved/saved only to the “USER” (User memory) and USB storage
devices with ID.
Note for “Protected 2 Original” and “Protected 2 Edited” Song file operation
Make sure to save the “Protected 2 Edited” Song to the same folder containing its original
“Protected 2 Original” Song. Otherwise the “Protected 2 Edited” Song cannot be played back.
Also, if you move a “Protected 2 Edited” Song, be sure to move its original “Protected 2
Original” Song to the same location (folder) at the same time.
Entering Characters
Touching [Symbol] (or [abc]) switches between entering symbols or Roman
letters (and numbers).
To switch between entering capital letters or small letters, touch (Shift).
: Roman letters and numbers in half size (full size)
: Symbols in half size (full size)
: Katakana in full size (half size)
: Hiragana and Kanji
To switch between full size or half size, touch and hold the Character Type. For example,
[ ] can be called up by holding [ ].
When entering Roman letters, you can switch between capital and small letters by
touching (Shift).
1
2
CVP-609/605 Owner’s Manual
34
Basic Operations
2 Tou ch []/[] or rotate the Data dial to move the cursor to the desired
location.
3 Input the desired character one by one.
To delete a single character, touch [Delete]; to delete all characters at once, touch
and hold [Delete]. To enter a space, touch the space key indicated in the illustration
on the previous page.
To input letters with auxiliary symbols (when Language is set to other than
Japanese):
You can input letters with auxiliary symbols such as umlaut by touching and holding
a letter to call up a list. For example, touch and hold “E” to enter “Ё” from the list.
To convert into Kanji (when the Language is set to Japanese):
When the entered “hiragana characters are shown in reverse display (highlighted),
touch [ ] several times to call up the conversion options. You can change the
reversed area by touching [] or []. When you find the desired Kanji, touch
[].
To change the converted kanji back to “hiragana,” touch [ ].
To clear the reversed area at once, touch [ ].
4 Touch [OK] to finalize the characters (name, keywords, etc.) you have
input.
NOTE
NOTE
CVP-609/605 Owner’s Manual
35
Basic Operations
Damper Pedal (Right)
Pressing this pedal sustains notes. Releasing this pedal
immediately stops (damps) any sustained notes. A
“half-pedal function of this pedal creates partial
sustain effects, depending on how far down you press
the pedal.
Half-pedal function
This function allows the sustain length to vary depending on how far the pedal is
pressed. The farther you press the pedal, the more the sound sustains. For example, if
you press the damper pedal and the notes you play sound a bit murky and loud with too
much sustain, you can partially release the pedal to lessen the sustain (murkiness).
Sostenuto Pedal (Center)
When the Piano Voice is selected, if you play a note or
chord on the keyboard and press this pedal while
holding the note(s), the notes will sustain as long as the
pedal is held. All subsequent notes will not sustain.
When a Voice other than piano is selected, a specific
function appropriate for the Voice is automatically
assigned to the center pedal.
Soft Pedal (Left)
When the Piano Voice is selected, pressing this pedal reduces the volume and slightly
changes the timbre of the notes you play. When a Voice other than piano is selected, a
specific function appropriate for the Voice is automatically assigned to the center pedal.
You can adjust the depth of the Soft pedal effect on the display called up via [Menu] →
[Assignable] → [Pedal]. For details, refer to the Reference Manual on the website.
Using the Pedals
If you press and hold the damper
pedal here, all the notes shown will be
sustained.
NOTE
NOTE
NOTE
GP Responsive Damper Pedal
This special pedal has been designed to provide enhanced tactile response and, when pressed,
is much closer in feel to the pedal of an actual grand piano. It makes it easier to physically
experience the half-pedal point and more easily apply the half-pedal effect than other pedals.
Since the pressing sensation may vary depending on the situation, including the location where
the instrument is installed, you can adjust the half-pedal point to the desired setting on the
display called up via [Menu] → [Assignable] → [Pedal]. For details, refer to the Reference
Manual on the website.
Assigning a function to each pedal
Various functions can be assigned to each of the three pedals and an optional foot controller/
footswitch — including start/stop of Song playback and controlling a Super Articulation Voice.
These can be set on the display called up via [Menu] → [Assignable] → [Pedal]. For details, refer
to the Reference Manual on the website.
If you press and hold the sostenuto
pedal here, only the notes held at this
timing will be sustained.
CVP-609/605 Owner’s Manual
36
Basic Operations
The [METRONOME ON/OFF] button lets you start or stop the metronome. The
metronome provides a click sound, giving you an accurate tempo guide when you
practice, or letting you hear and check how a specific tempo sounds.
The TEMPO [-] and [+] buttons let you change the playback tempo of Metronome, Style
and MIDI Song. The tempo of the Style and MIDI Song can also be adjusted via the
[TAP] button.
TEMPO [-]/[+] buttons
Press the TEMPO [-] or [+] button to call up the Tempo pop-up display. Use the
TEMPO [-]/[+] buttons to decrease or increase the tempo over a range of 5 – 500 beats
per minute. Holding down either button can change the value continuously. Pressing
both TEMPO [-] and [+] buttons can call up the default tempo of the last selected Style
or Song.
[TAP] button
During playback of a Style or MIDI Song, you can change the tempo by tapping the
[TAP] button twice at the desired tempo. When Style and Song are stopped, tapping the
[TAP] button (four times for a 4/4 time signature) starts playback of the rhythm part of
the Style at the tempo you tapped.
Using the Metronome
NOTE
Adjusting the Tempo
NOTE
CVP-609/605 Owner’s Manual
37
Basic Operations
Touch Sensitivity determines how the sound responds to your playing strength. This
setting does not change the weight of the keyboard.
1 Call up the display via [Menu] → [Keyboard].
2 Make the settings by touching the display.
Maintaining the Left Voice (even when releasing the keys)
When the Left Hold function is set to “On” in the display above, the Left Voice is held
even when the keys are released. Nondecaying Voices such as strings are held
continuously, while decay-type Voices such as piano decay more slowly (as if the sustain
pedal has been pressed).
When the Left Hold is “On,” an “H” indication appears at the left side of the keyboard
illustration in the center of the Home display.
This function is convenient when used along with Style playback since the sound of the
chord matching Style playback is maintained. To stop the Left Voice which is sounding,
stop Style or Song playback, or set the Left Hold function to “Off.
Setting the Touch Sensitivity of the Keyboard
Touch Cur ve
Enter checkmarks to the boxes of the desired keyboard parts, then
touch here to call up the setting window and select the Touch
Sensitivity type. If you remove the checkmark, playing the
corresponding part will produce a fixed velocity regardless of your
playing strength.
Hard2: Requires strong playing to produce high volume. Best for
players with a heavy touch.
Hard1: Requires moderately strong playing for high volume.
Medium: Standard Touch Sensitivity.
Soft1: Produces high volume with moderate playing strength.
Soft2: Produces relatively high volume even with light playing
strength. Best for players with a light touch.
Fixed Velocity
Make sure that the box of the desired keyboard parts are checked,
then touch here to call up the setting window and set the velocity
with which you play the keys, which stays fixed regardless of your
playing strength.
NOTE
CVP-609/605 Owner’s Manual
38
Basic Operations
The TRANSPOSE [-]/[+] buttons transpose the overall pitch of the instrument (the
keyboard sound, Style playback, MIDI Song playback, and so on) in semitone steps
(from -12 to 12). Pressing the [-] and [+] buttons simultaneously resets the value to 0.
You can independently select the part to transpose as desired. Touch the Transpose pop-
up several times until the desired part appears, then use the TRANSPOSE [-]/[+]
buttons to transpose it.
From the Balance display called up via [Menu] → [Balance], you can adjust the volume
balance between the keyboard parts (Main, Layer and Left), Style and Song and the
microphone sound. Slide your finger vertically for each part to adjust the volume.
Since the volume of MIDI Songs and Audio Songs are handled individually, you need to
set the volume balance for each case (when a MIDI Song is selected, or when an Audio
Song is selected).
Transposing the Pitch in Semitones
NOTE
Master
Transposes the pitch of the entire sound with the exception of the Audio
Song and input sound from a microphone or the [AUX IN] jack.
Keyboard
Transposes the keyboard pitch including the chord root triggering Style
playback.
Song
Transposes the pitch of the MIDI Song.
NOTE
Fine tuning the pitch
By default, the pitch of the entire instrument is set to 440.0 Hz with the Equal Temperament.
This setup can be changed from the display called up via [Menu] → [Tuning]. For details, refer
to the Reference Manual on the website.
Adjusting the Volume Balance
CVP-609/605 Owner’s Manual
39
Basic Operations
While holding the C7 key (right-most key on the keyboard), turn the power on. This
restores the all settings to the factory default.
If you want to restore the default value of any parameter you’ve changed, touch and hold
the value on the display (page 25).
You can back up all data in the User memory of this instrument (except for Protected
Songs) and all settings to the USB flash memory as a single file. This procedure is
recommended for data security and backup in case of damage.
1 Connect the USB flash memory to the [USB TO DEVICE] terminal as
backup destination.
2 Call up the display via [Menu] → [Utility] → [Factory Reset/ Backup] →
page 2/2.
3 Touch [Backup] of “All” to save the backup file to the USB flash
memory.
Restoring the Backup File
To do this, touch [Restore] of “All” in step 3 above. When the operation is complete, the
instrument will be restarted automatically.
Restoring the Factory-programmed Settings
+
C7
NOTE
Data Backup
NOTE
NOTE
3
NOTE
CVP-609/605 Owner’s Manual
40
Piano Room – Enjoying the Piano Performance –
Piano Room
– Enjoying the Piano Performance –
If you want to simply play the instrument as a piano without having to worry about other unrelated settings, the Piano
Room function is exceptionally convenient. No matter what settings you’ve made from the panel, you can instantly call
up the settings for the piano performance by a single button press. You can also change the piano settings as you like.
1 Press the [PIANO ROOM] button to call up the Piano Room display.
This operation calls up the panel settings for the piano performance and disables
all other functions except for the pedal, metronome and master volume setting.
2 Play the keyboard.
You can play with the pedal (page 35) and metronome (page 36).
3 Touch [×] at the upper right of the display to exit from the Piano Room
display.
The panel settings return to the ones last made before you called up the Piano
Room display.
The Piano Room display lets you set various parameters such as piano type. The settings
here are applied only when the Piano Room display is shown. The settings you made on
another display will not be applied when the Piano Room display is shown.
1 Press the [PIANO ROOM] button to call up the Piano Room display.
Playing the Piano Performance
Making the Desired Setup in the Piano Room
2
CVP-609/605 Owner’s Manual
41
Piano Room – Enjoying the Piano Performance –
2 Make the desired setups by touching the display.
Selecting a piano type
Touch the picture of the piano to call up the piano list at the bottom of the display,
then select the desired one. The last selected environment for the piano (see below)
will automatically be called up when you select a particular piano.
Selecting an environment (reverb type)
Touch the background picture of the piano to call up the environment list at the
bottom of the display, then select the desired one.
Making detailed settings
Touch the (Settings) to call up the detailed settings menu. Make the desired
settings for the selected piano type by touching the parameters. Depending on the
selected piano type, some parameters may not be available.
Touching (Help) provides on-screen instructions for some of the settings.
The settings in the Piano Room display will be maintained even if you exit from
this display or turn off the power. Pressing the [PIANO ROOM] button next time
will call up the Piano settings which were made the previous time.
Piano Lock Function
You can “lock” the panel settings in the Piano Room settings you made last time. Once
locked, the instrument stays in the Piano Room settings, even if other buttons are
pressed — allowing you to play the keyboard, use the pedals, or adjust the master
volume only.
1 Press and hold down the [PIANO ROOM] button for two seconds or
longer.
A message appears in the display.
2 Touch [Lock] to call up the Piano Lock display.
The panel settings will be locked in the Piano Room settings you made.
If you turn off the power with Piano Lock enabled, turning on the power next time will
call up the Piano Lock display.
To disable Piano Lock, press and hold the [PIANO ROOM] button again for two
seconds or longer.
NOTE
Lid Position
Determines how much the Lid is opened.
To uc h
Determines how the sound responds to the strength with which
you play the keys. “Soft” produces high volume with moderate
playing strength. “Medium” is the standard touch response.
“Hard” requires moderately strong playing for high volume.
Tune
Determines the pitch of this instrument in 1Hz steps.
Damper Resonance
Determines whether the Damper Resonance effect is enabled or
disabled created when you press the Damper Pedal.
String Resonance
Turns String Resonance on or off.
Key Off Sampling
Determines whether very delicate noises are produced or not
when keys are released.
Reset
Restores all settings above for the selected piano type to the
default.
CVP-609/605 Owner’s Manual
42
Voices Playing the keyboard
Voices
– Playing the keyboard –
The instrument features a wide variety of exceptionally realistic instrumental Voices, including piano, guitar, strings,
brass, wind instruments and more.
The Voices can be played via three keyboard parts: Main, Layer and Left. These playing
modes allow you to play just one single Voice (Main), play two different Voices in layer
(Main and Layer), or play different Voices in the right- and left-hand areas of the
keyboard (Main/Layer and Left). By combining these three parts, you can create
luscious instrument textures and convenient performance combinations.
When the Left part is turned off, the entire keyboard is used for the Main and Layer
parts. When the Left part is turned on, the F 2 and lower keys are used for the Left part
while the upper keys (excluding F 2) are used for the Main and Layer parts. The key
which divides the keyboard into the left-hand and right-hand areas is referred to as
Split Point” and its guide lamp lights when the Left part is turned on. The Voices of the
parts which are turned on can be confirmed on the Home display.
1 Select the keyboard part then call up the Voice Selection display.
Do this to select a Voice for each keyboard part.
Touchi ng th e displ ay
1-1 On the Home display, touch [Main], [Left], or [Layer] to turn on the
desired keyboard part.
The center of the display shows the keyboard parts which are turned on and their
corresponding Voices.
1-2 Touch the Voice of the desired part to call up the Voice Selection display.
Playing Preset Voices
NOTE
Left part
Layer part
Main part
Split Point (F 2 as default)
NOTE
NOTE
Keyboard parts which
are turned on and their
Voices
On/off status of the
keyboard parts
CVP-609/605 Owner’s Manual
43
Voices – Playing the keyboard –
Using the panel buttons
1-1 To select the keyboard part, press the VOICE [MAIN/LAYER/LEFT]
button repeatedly if necessary until the desired part’s lamp lights.
1-2 Press one of the desired VOICE category buttons to call up the Voice
Selection display.
2 Tou ch the desi re d Voi ce.
3 Make sure that the desired keyboard part is turned on.
The on/off setting for the keyboard part can be made as described in step 1-1 in
“Touching the display” above.
4 Play the keyboard.
NOTE
1-1
1-2
NOTE
NOTE
To hear the characteristics of the Voices:
Touch (Demo) to start demo playback of the selected Voice. Touch (Demo) again to
stop playback.
Touch (Information) to call up the Voice Information window, which may or may not be
available depending on the Voice.
CVP-609/605 Owner’s Manual
44
Voices Playing the keyboard
Calling up the default Piano Settings (Piano Reset)
When you turn the power on, the Voice is set to “Concert Grand,” allowing you to play
the instrument as a piano across the entire keyboard. No matter what settings you’ve
made from the panel, you can instantly call up these default settings.
1 Press and hold down the [PIANO ROOM] button for two seconds or
longer.
A message appears in the display.
2 Touch [Reset] to call up the default piano settings.
Voi c e Charac teristi cs
At the left side of each Voice name on the Voice Selection display, the icon which represents its
defining characteristic is indicated.
There are various Voice characteristics; however, only the following ones are covered here. For
detailed explanations, refer to the Reference Manual on the website.
•/: Super Articulation (SA, SA2) Voices
The word “articulation” in music usually refers to the transition or continuity between notes. This is often
reflected in specific performance techniques, such as staccato, legato and slur. For details, refer to page 46.
: Organ Flutes Voices
Lets you recreate all of the classic organ sounds by adjusting the flute footage levels and the percussive
sounds, just like on conventional organs. For details, refer to page 47.
/ : Drum Voices, / : SFX Voices
Lets you play various drums and percussion instruments or SFX (sound effects) sounds on the keyboard.
Details are given in the Drum/Key Assignment List of the separate Data List.
NOTE
CVP-609/605 Owner’s Manual
45
Voices – Playing the keyboard –
The key which divides the keyboard into two or three areas is referred to as “Split Point.
There are two types of Split Point: “Left Split Point” and “Style Split Point.” The “Left
Split Point” divides the keyboard into the Left Voice area and Main Voice area while the
Style Split Point” divides the keyboard into the Chord area and the Main or Left Voice
area. Though both Split Points are at the same key (F 2) by default, you can also set
them individually (as shown).
1 Call up the Split Point/Fingering window: [Menu] → [Split&Fingering].
2 Touch [Left] or [Style] to turn it on.
If you want to set both Split Points to the same key, turn both of them on.
3 Tou ch []/[] to select the desired key as Split Point.
You can set the Split Point also by pressing the actual key while holding down the
keyboard illustration on the display.
Setting the Split Point
Style Split Point
Left Split Point
Chord area
Left Voice area
Left Voice, Main (and Layer) Voice area
Main (and Layer) Voice area
NOTE
3
2
Style Split Point
Left Split Point
NOTE
CVP-609/605 Owner’s Manual
46
Voices Playing the keyboard
The Super Articulation Voices (SA Voices and SA2 Voices) enable you to create subtle,
very realistic musical expressions, simply by how you play.
SA Voices
The SA Voices provide many benefits with great playability and expressive control in
real time.
Example: Saxophone Voice
If you play a C note and then an adjacent D in a very legato way, you will hear the note
change seamlessly, as though a saxophone player played it in a single breath.
Example: Guitar Voice
If you press and hold a C note then press the left pedal, the pitch will change from C to D
note as if a guitarist played a hammer-on note.
SA2 Voices (only for the CVP-609)
For wind instrument Voices and Violin Voices, a special technology called AEM has
been used, which features detailed samples of special expressive techniques used on
those specific instruments — to bend or slide into notes, to “join” different notes
together, or to add expressive nuances at the end of a note, etc.
Example: Clarinet Voice
If you hold a C note and play the B above, you’ll hear a glissando up to the B .
Some “note off” effects are also produced automatically when you hold a note for over a
certain time.
For specific performance instructions on certain Voices, you can call up the Information
window of the selected SA Voice or SA2 Voice by touching the [S.Art] or [S.Art2] icon
which appears on the upper right of the Voice name on the Home display.
Playing Super Articulation Voices
NOTE
Adding Articulation Effects by Using the Pedal
When you assign a SA or SA2 Voice to the Main part, the function of the center and left pedals
are switched to control articulation effects. Pressing a pedal triggers different playing effects,
separate from your keyboard playing. For example, pressing a pedal for a saxophone Voice can
produce breath noises or key noises, while doing the same for a guitar Voice can produce fret
noises or body-tapping sounds. You can effectively intersperse these into the notes as you play.
When an SA2 Voice is selected (CVP-609), pressing a pedal and playing/releasing a note
enables you to add articulation effects, such as bend up/down, glissando up/down, brass falls,
etc.
NOTE
CVP-609/605 Owner’s Manual
47
Voices – Playing the keyboard –
The instrument uses advanced digital technology to recreate the legendary sound of
vintage organs. Just as on a traditional organ, you can create your own sound by
increasing and decreasing the levels of the flute footages. The created Voice can be saved
for future recall.
1 On the Voice Selection display, select the desired Organ Flutes Voice.
Touch the [Organ Flutes] tab in the [Organ] category, then select the desired Organ
Voi ce.
2 Return to the Home display, then touch (Organ Flutes) located at
the upper right of the Voice name to call up the Organ Flutes Voice Edit
display.
3 Slide the Footage levers to adjust the footage settings.
The footage settings determine the basic sound of the Organ Flutes.
If you want, you can select the Organ type, change the settings such as Rotary
Speaker and Vibrato.
4 Touch (Save) and save the created Organ Voice.
For instructions on saving, refer to page 29.
Creating Original Organ Flutes Voices
NOTE
NOTE
3
NOTE
Organ Type
Specifies the type of organ tone generation to be simulated.
Volu me
Determines the volume of the entire Organ Flutes sound.
Rotary Speaker
Alternately switches between the slow and fast rotary speaker
speeds. This parameter is available when an Effect type in the
ROTARY SP category is selected.
Vibrato
Turns the vibrato on or off, and allows you to adjust the
vibrato depth and vibrato speed.
Response
Adjusts the response speed of both the Attack and Release
portions of the sound.
Attack
Switches between two different Attack modes: First and
Each, and determines the length of the Attack sound.
CVP-609/605 Owner’s Manual
48
Styles – Playing Rhythm and Accompaniment –
Styles
– Playing Rhythm and Accompaniment –
The instrument features a variety of accompaniment and rhythmic backing patterns (called “Styles”) in a variety of
different musical genres including pop, jazz, and many others. Each Style features Auto Accompaniment, letting you
produce automatic accompaniment playback simply by playing “chords” with your left hand. This lets you
automatically recreate the sound of a full band or orchestra — even if youre playing by yourself.
Try out Style accompaniment with the following song. After you understand how to use the Style, try out other songs by
using various Styles.
Mary Had a Little Lamb (Style: Country 8Beat)
1 On the Home display, touch the Style name to call up the Style Selection
display.
2 Tou ch the de si re d Sty l e.
For the example score above, touch [Country & Blues] category and touch
[Modern Country], then touch [Country 8Beat].
The Style category can be selected also by pressing one of the STYLE buttons.
Playing with a Style
C
CFC
C
G
G
CC
Ending
NOTE
1
CVP-609/605 Owner’s Manual
49
Styles – Playing Rhythm and Accompaniment –
3 Make sure that the STYLE CONTROL [ACMP ON/OFF] button is
turned on.
When turned on, the specific left-hand section of the keyboard can be used as the
Chord section, and chords played in this section are automatically detected and
used as a basis for fully automatic accompaniment with the selected Style.
4 Return to the Home display, touch [] at the upper left to expand the
Style area, then touch [ ] (SYNC START) to enable Sync Start.
Here and in the later steps, the operation in the Style area of the Home display can
be controlled by the STYLE CONTROL buttons (page 50).
5 Play a chord with your left hand to start the selected Style.
Referring to the notation on page 48, play chords with your left hand and a melody
with your right.
6 Tou ch [ / ] (START/STOP) to stop Style playback.
You can also stop playback by pressing one of the ENDING [I] – [III] buttons at the
“Ending” location on the notation (page 48).
A Style consists of eight parts (channels): rhythm, bass, etc. You can add variations and
change the feeling of a Style by selectively turning channels on/off or by changing the
Voices (page 83).
Chord section
Split Point (F 2 as default)
NOTE
Style Characteristics
The Style type and its defining characteristics are indicated on the Preset Style icon (such as
Pro and Session). For details, refer to the Reference Manual on the website.
4
6
CVP-609/605 Owner’s Manual
50
Styles – Playing Rhythm and Accompaniment –
To do this, use the on-screen buttons called up by touching [] in the Style area of the
Home display, or use the STYLE CONTROL buttons.
[ACMP ON/OFF], [AUTO FILL IN] and [SYNC STOP] can be controlled only by using
the panel buttons.
To Start/Stop Playing
[ / ] (START/STOP)
Starts playback of the rhythm part of the current Style. To stop
playback, press this button again.
[ ] (SYNC START)
This puts the Style playback in “standby.” The Style starts playing
back when you play a chord with your left hand (when [ACMP
ON/OFF] is on) or you press any note on the keyboard (when
[ACMP ON/OFF] is off). During Style playback, pressing this
button stops the Style and puts playback in “standby.
[SYNC STOP] button
You can start and stop the Style anytime you want by
simply playing or releasing the keys in the chord section
of the keyboard. Make sure that the [ACMP ON/OFF]
button is on, press the [SYNC STOP] button, then play
the keyboard.
Style Control Operations
NOTE
Playing back both rhythm and auto accompaniment
If you turn on the [ACMP ON/OFF] button, both the rhythm part and
auto accompaniment can be played back when playing chords in the
chord section during Style playback.
Style Control Style Control
While Style is stopped While Style is playing
STYLE CONTROL buttons
Home display
NOTE
NOTE
CVP-609/605 Owner’s Manual
51
Styles – Playing Rhythm and Accompaniment –
INTRO [I] – [III]
The instrument features three different Intro sections to add an
introduction before starting Style playback. After pressing (or
touching) one of the INTRO [I] – [III] buttons, start playback of
the Style. When the Intro finishes playing, Style playback
automatically shifts to the Main section.
ENDING [I] – [III]
The instrument features three different Ending sections to add an
ending before stopping Style playback. When you press (or touch)
one of the ENDING [I] – [III] buttons while a Style is playing back,
the Style will automatically stop after the ending is played. You can
have the ending gradually slow down (ritardando) by pressing the
same ENDING button once again, while the ending is playing.
Changing Variation (Sections) During Style Playback
Each Style features four different Main sections, four Fill-in sections and a Break
section. By using these sections effectively, you can easily make your performance sound
more dynamic and professional. The section can be freely changed while the Style is
playing back.
MAIN VARIATION [A] − [D]
Press (or touch) one of the MAIN VARIATION [A] – [D] to select the desired Main
section (the button lights in red). Each is an accompaniment pattern of a few measures
and it plays indefinitely. Pressing the selected MAIN VARIATION button again
maintains the same section, but plays an appropriate fill-in pattern to spice up the
rhythm and break the repetition.
[] (BREAK)
This lets you add dynamic breaks in the rhythm of the
accompaniment. Press this button during Style playback. When
the one-measure Break pattern finishes playing, the Style
playback automatically shifts to the Main section.
NOTE
AUTO FILL function
When the [AUTO FILL IN] button is turned on, pressing any of the
Main [A] − [D] buttons as you play automatically plays a fill-in section.
About the lamp status of the section buttons (INTRO/MAIN VARIATION/
BREAK/ENDING)
Red: The section is currently selected.
Red (flashing): The section will be played next, following the currently selected section.
* The Main [A] − [D] button lamps also flash in red.
Green: The section contains data but is not currently selected.
Off: The section contains no data and cannot be played.
Press the selected Main section
(lit in red) again.
The fill-in of the selected Main
section plays (flashes in red).
NOTE
CVP-609/605 Owner’s Manual
52
Styles – Playing Rhythm and Accompaniment –
One Touch Setting is a powerful and convenient feature that automatically calls up the
most appropriate panel settings (Voices or effects, etc.) for the currently selected Style,
with the touch of a single button. If youve already decided which Style you wish to use,
you can have One Touch Setting automatically select the appropriate Voice for you.
1 Select the desired Style (steps 1– 2 on page 48).
2 Press one of the ONE TOUCH SETTING [1] − [4] buttons.
Not only does this instantly call up all the settings (Voices, effects, etc.) that match
the current Style, it also automatically turns on ACMP and SYNC START, so that
you can immediately start playing the Style.
3 As soon as you play a chord with your left hand, the selected Style
starts.
Each Style has four One Touch Setting setups. Press the other ONE TOUCH
SETTING [1] − [4] buttons to try out other setups.
Calling up Panel Settings Appropriate for the
Current Style (One Touch Setting)
Confirming the One Touch Setting Contents
In the Style Selection display, touch (Information) to call up the Information window that
shows what Voices are assigned to the ONE TOUCH SETTING [1] – [4] buttons for the
current Style. You can call up the desired settings also by touching one of the One Touch
Settings 1– 4 directly on the Information window.
NOTE
Automatically Changing One Touch Settings with the Main Sections
The convenient OTS (One Touch Setting) Link function lets you automatically
have One Touch Settings change when you select a different Main section (A −
D). The Main sections A, B, C and D correspond to One Touch Settings 1, 2, 3
and 4 respectively. To use the OTS Link function, turn the [OTS LINK] button
on.
NOTE
CVP-609/605 Owner’s Manual
53
Styles – Playing Rhythm and Accompaniment –
Memorizing original settings to One Touch Setting
You can memorize your original panel settings to the One Touch Setting. The newly
created One Touch Setting will be saved in the User tab as a User Style, and you can call
up the One Touch Setting as a part of the Style file.
1 Select the desired Style to memorize your One Touch Setting.
2 Make the desired panel settings, such as those for Voices and Effects.
3 Press the [MEMORY] button of REGISTRATION MEMORY.
4 Press one of the ONE TOUCH SETTING [1] – [4] buttons.
A message appears prompting you to save the panel settings.
5 Touch [Yes] to call up the Style Selection display for saving your data,
then save the current settings as a User Style.
For instructions on saving, refer to page 29.
You can search for music pieces and songs that are most suitable for playing with the
current Style by using the Music Finder Records (page 74). You can automatically call up
appropriate settings such as Voice, effect and pedal by selecting the desired music piece.
1 Select the desired Style (steps 1– 2 on page 48).
2 In the Style Selection display, touch (Search).
The music pieces which can be played with the current Style are listed on the
display.
3 Select the desired music piece.
The appropriate panel settings for playing the music piece are called up.
3 4
NOTE
Searching for Suitable Songs for the Current Style
NOTE
NOTE
32
NOTE
CVP-609/605 Owner’s Manual
54
Styles – Playing Rhythm and Accompaniment –
This convenient function “recommends” optimum Styles for the song you want to
perform, based on the rhythm you play for one or two measures.
1 On the Style selection display, touch (Recommender) to call up the
Style Recommender display.
The keyboard is divided (at the B0 key) into two sections as below. The drum
instruments (Kick, Snare and Hi-Hat) are assigned to the left-hand section while
the piano sound is assigned to the right.
2 Use the Style Recommender function to find the Style.
2-1 Touch [Start] to start the metronome, indicating that the Style
Recommender function starts.
As necessary, use the TEMPO [-]/[+] buttons or [TAP] button to adjust the tempo, and
touch []/[] on the display to select the beat.
2-2 Play the rhythm you have in mind on the Drum or Piano section for one or
two measures along with the metronome.
The timing at which you play the keys is analyzed over several seconds, then playback
of the most recommended Style starts. In addition, the candidates of the other
recommended Styles are listed in the display.
Example 1:
Play the following rhythm in the Piano section of the keyboard.
Bossa Nova Styles or those of a similar feel may be listed on the display.
Example 2:
Play the following rhythm in the Drum section of the keyboard.
8-beat Styles or those of a similar feel may be listed on the display.
Calling up Optimum Styles for Your Performance
(Style Recommender)
2-1
1
B0
Hi-Hat
Snare
Kick
PianoDrum
NOTE
NOTE
Snare
Kick
CVP-609/605 Owner’s Manual
55
Styles – Playing Rhythm and Accompaniment –
3 Select the desired Style from the list.
Listen to the recommended Styles by changing the Sections (page 51), playing
chords in the Piano section and adjusting the tempo (page 36). If the Style called up
doesnt match the song you want to play, touch [Retry], then return to step 2-2.
4 When you’ve found a Style you’re satisfied with, touch [OK] to exit
from the Style Recommender display.
5 Play the keyboard along with the Style you just found.
By changing the Chord Fingering type, you can automatically produce appropriate
accompaniment even if you dont press all of the notes which comprise a chord. Seven
types are available.
1 Call up the Split Point/Fingering window: [Menu] → [Split&Fingering].
2 Tou ch []/[] to select the desired Fingering Type.
Changing the Chord Fingering Type
NOTE
Single Finger
Lets you easily play chords in the accompaniment range of the
keyboard using only one, two or three fingers. This type is available
only for Style playback.
Major chord
Press the root key only.
Minor chord
Simultaneously press the root key and a black key
to its left.
Seventh chord
Simultaneously press the root key and a white key
to its left.
Minor seventh chord
Simultaneously press the root key and both a white
and black key to its left.
Multi Finger
Automatically detects Single Finger or Fingered chord fingerings, so
you can use either type of fingering without having to switch
fingering types.
2
C
Cm
7
C
Cm
7
CVP-609/605 Owner’s Manual
56
Styles – Playing Rhythm and Accompaniment –
Fingered
Lets you finger your own chords on the chord section of the
keyboard, while the instrument supplies appropriately orchestrated
rhythm, bass, and chord accompaniment in the selected Style. The
Fingered type recognizes the various chord types which are listed
on the separate Data List booklet and can be looked up using the
Chord Tutor function called up via [Menu] → [ChordTutor].
Fingered On
Bass
Accepts the same fingerings as Fingered, but the lowest note played
in the Chord section of the keyboard is used as the bass note,
allowing you to play “on bass” chords. (In the Fingered mode, the
root of the chord is always used as the bass note.)
Full Keyboard
Detects chords in the entire key range. Chords are detected in a way
similar to Fingered, even if you split the notes between your left and
right hands — for example, playing a bass note with your left hand
and a chord with your right, or by playing a chord with your left
hand and a melody note with your right.
AI Fingered
Basically the same as Fingered, with the exception that less than
three notes can be played to indicate the chords (based on the
previously played chord, etc.).
AI Full
Keyboard
When this advanced fingering type is engaged, the instrument will
automatically create appropriate accompaniment while you play
just about anything, anywhere on the keyboard using both hands.
You don’t have to worry about specifying the Style chords. Although
the AI Full Keyboard type is designed to work with many songs,
some arrangements may not be suitable for use with this feature.
This type is similar to Full Keyboard, with the exception that less
than three notes can be played to indicate the chords (based on the
previously played chord, etc.). 9th, 11th and 13th chords cannot be
played. This type is available only for Style playback.
CVP-609/605 Owner’s Manual
57
Song Playback – Playing and Practice Songs
Song Playback
– Playing and Practice Songs –
For the Clavinova, “Song” refers to MIDI or audio data which include preset songs, commercially available music files,
etc. Not only can you play back a Song and listen to it, but you can also play the keyboard along with Song playback.
There are two kinds of Songs that can be recorded and played back on this instrument: MIDI Songs and Audio Songs.
• MIDI Song
A MIDI Song is comprised of your keyboard performance information and is not a recording of the actual sound itself.
The performance information refers to which keys are played, at what timing, and at what strength — just as in a
musical score. Based on the recorded performance information, the tone generator (of the Clavinova, etc.) outputs the
corresponding sound. Since MIDI Song data contains the information such as keyboard part and Voice, you can
practice effectively by viewing the score, turning the particular part on or off, or changing Voices.
• Audio Song
An Audio Song is a recording of the performed sound itself. This data is recorded in the same way as that used in
recording cassette tapes, or with voice recorders, etc. You can play commercially available music on this instrument (as
long as the files have been converted to WAV or MP3 format), just like you do on a portable music player.
Availability of functions differs between MIDI Songs and Audio Songs. In this chapter, the following icons indicate
whether or not the explanation applies to MIDI Songs or Audio Songs individually.
Example: … Indicates explanation applies only to MIDI Songs.
You can play back the following types of Songs.
Preset Songs (MIDI Songs)
Your own recorded Songs (see page 66 for instructions on recording)
Commercially available Songs: MIDI files in SMF (Standard MIDI File) format,
Audio files in WAV or MP3 format.
If you want to play back a Song in USB flash memory, connect the USB flash memory
containing Song data to the [USB TO DEVICE] terminal beforehand.
1 On the Home display, touch the Song name to call up the Song
Selection display.
MIDI
Audio
Playback of Songs
MIDI Audio
NOTE
NOTE
WAV 44.1 kHz sample rate, 16 bit resolution, stereo
MP3 MPEG-1 Audio Layer-3: 44.1/48.0 kHz sample rate, 64 – 320 kbps and variable bit
rate, mono/stereo
NOTE
1
CVP-609/605 Owner’s Manual
58
Song Playback – Playing and Practice Songs –
2 Touch the desired Song on the display to select it.
A Preset Song can be selected from one of the following tabs:
• Usage: The Songs are divided into several usages.
• Title: The Songs are sorted in alphabetical order.
• Genre: The Songs are divided into several genres.
The Songs you recorded or the commercially available songs can be selected from
one of the following tabs:
• : MIDI Songs are listed.
• : Audio Songs are listed.
3 Return to the Home display, touch [] at the upper right to expand the
Song area, then touch [ / ] (PLAY/PAUSE) to start playback.
Here and in the later steps, the operation in the Song area of the Home display can
be controlled by the SONG CONTROL buttons (page 59).
4 Tou ch [ ] (STOP) to stop playback.
NOTE
Viewing Song information
When an Audio Song or a protected MIDI Song is selected, touching (Information) calls
up the Song Information window.
Queuing the next Song for playback (MIDI Song only)
While a MIDI Song is playing back, you can queue up the next MIDI Song for playback. This is
convenient for chaining it to the next Song smoothly during stage performance. Select the
Song you want to play next in the Song Selection display, while a Song is playing back. The
[Next] icon appears at the right side of the corresponding Song name. To cancel this setting,
touch the [Next] icon.
4
3
CVP-609/605 Owner’s Manual
59
Song Playback – Playing and Practice Songs
Song Control Operations
To control Song playback, you can use the on-screen buttons called up by touching []
in the Song area of the Home display, or use the SONG CONTROL buttons.
Keep in mind that, unlike with certain panel button operations, you cannot touch
two buttons simultaneously on the display.
Pause
Press (or touch) the [ / ] (PLAY/PAUSE) during playback. Pressing it again resumes
Song playback from the current position.
Rewind/Fast Forward
Press (or touch) the [ ] (REW) or [ ] (FF) during playback or while the Song
stopped. Pressing one of them once moves one measure back/forward for MIDI Songs,
or one second for Audio Songs. Holding one of them scrolls backward/forward
continuously.
When you press (or touch) [ ] (REW) or [ ] (FF), a pop-up window appears
showing the current position of the Song.
NOTE
Song Control
Home display
SONG CONTROL buttons
NOTE
For Audio Songs
The Phrase Mark number appears only when a
MIDI Song containing Phrase Marks is selected.
You can choose to rewind/fast forward the Song in
“Bar” or “Phrase Mark” units by touching the pop-up
window beforehand.
For MIDI Songs
Current measure number
Phrase Mark number
Elapsed
time
NOTE
CVP-609/605 Owner’s Manual
60
Song Playback – Playing and Practice Songs –
Synchro Start (MIDI Song)
You can conveniently start playback of a MIDI Song as soon as you start playing the
keyboard. While playback is stopped, hold down the SONG CONTROL [STOP] button
and press the [PLAY/PAUSE] button. To cancel the Synchro Start function, hold down
the SONG CONTROL [STOP] button and press the [PLAY/PAUSE] button once again.
You can view the music notation (score) of the selected Song. We suggest that you read
through the music notation before starting to practice.
1 Select a MIDI Song (steps 1 − 2 on page 57).
2 Call up the Score display via [Menu] → [Score].
You can look through the entire notation by touching [] or [] when the Song
playback is stopped. As starting playback, the “ball” bounces along through the
score, indicating the current position.
You can change the displayed notation style. For details on the Score display, refer to the
Reference manual on the website.
Moving the Song Playback Position
In the Song area (when expanded) of the Home display, the current position of the Song
playback is shown. This can be moved forward or backward by moving the slider on the
display.
When an Audio Song is selected:When a MIDI Song is selected:
Current measure number Last measure number Elapsed time Total time
NOTE
Displaying Music Notation (Score)
MIDI
Audio
For changing the page.
NOTE
CVP-609/605 Owner’s Manual
61
Song Playback – Playing and Practice Songs
When the selected Song contains lyric data, you can view it on the instruments display
during playback.
1 Select a MIDI Song (steps 1 − 2 on page 57).
2 Call up the Lyrics display via [Menu] → [Lyrics].
When the Song data contains lyrics data, the lyrics are shown on the display. You
can look through the entire lyrics by touching [] or []when Song playback is
stopped. As Song playback starts, the color of the lyrics changes, indicating the
current position.
For details on the Lyrics display, refer to the Reference manual on the website.
Displaying Lyrics
MIDI
Audio
NOTE
For changing the page.
NOTE
CVP-609/605 Owner’s Manual
62
Song Playback – Playing and Practice Songs –
Regardless of whether a Song is selected or not, you can view the text file (.txt) created
by using a computer on the instruments display. This feature enables various useful
possibilities, such as the showing of lyrics, chord names, and text notes.
If you want to view the text in a USB flash memory, connect the USB flash memory
containing text data to the [USB TO DEVICE] terminal beforehand.
1 Call up the Text display via [Menu] → [TextViewer].
2 Touch the bottom left corner on the display to call up the Text File
Selection display.
3 Select the desired text file, and touch [Close] to show the text in the
display.
You can look through the entire text by touching [] or []. To clear the text from
the display, touch [] located at right of the text file name.
For detailed operations such as changing the font style, refer to the Reference Manual on
the website.
Displaying Text
NOTE
2
For changing the page.
NOTE
NOTE
CVP-609/605 Owner’s Manual
63
Song Playback – Playing and Practice Songs
You can mute the right-hand part to try practicing that part on your own. The
explanations here apply when you practice the right-hand part with “Follow Lights” of
the Guide functions. The guide lamps indicate the notes you should play and when you
should play them. You can also practice at your own pace — since the accompaniment
waits for you to play the notes correctly.
1 Select a MIDI Song and call up the Score display (page 60).
2 Touch (Playback Settings) to call up the Playback Settings menu.
3 Touch [Guide] to turn it on.
4 Touch [Right] to turn off the right-hand part.
The right-hand part is muted and the Guide for the right-hand part is enabled.
5 Press the SONG CONTROL [PLAY/PAUSE] button to start playback.
Practice the right-hand part at your own pace along with the guide lamps. The
playback of the Left and Extra parts will wait for you to play the notes correctly.
After you’ve finished practicing, touch [Guide] to turn off the Guide function.
One-handed Practice with the Guide Function
MIDI
Audio
NOTE
234
NOTE
NOTE
Other guide functions
In addition to the “Follow Lights” function explained above, there are more functions in the
Guide features, for practicing the timing of playing the keys (Any Key mode), for Karaoke or
for practicing a song at your own pace (Your Tempo). You can select the functions via [Menu]
→ [SongSetting] → [Guide] → [Type].
For more information, refer to the Reference Manual on the website.
CVP-609/605 Owner’s Manual
64
Song Playback – Playing and Practice Songs –
The Song Repeat functions can be used to repeatedly play back a Song or a specific range
of measures in a Song. This function controlled in the Song area (when expanded) of the
Home display is useful for repeated practicing of difficult-to-play phrases.
To repeat an entire Song, turn on (A-B Repeat) in the display and start playback of
the Song. To cancel Repeat playback, turn off (A-B Repeat).
Specifying a Range of Measures and Playing them Back
Repeatedly (A-B Repeat)
1 Select a Song (steps 1 − 2 on page 57).
2 Tou ch [ / ] (PLAY/PAUSE) to start playback.
3 Specify the repeat range.
When playback reaches the point you want to specify as the starting point (A), turn
on (A-B Repeat). When playback reaches the point you want to specify as the
ending point (B), touch (A-B Repeat) again. The range from Point A to Point
B will be played back repeatedly. For MIDI Songs, an automatic lead-in (to help
guide you into the phrase) is added before Point A.
4 Tou ch [ ] (Stop) to stop playback.
The Song position will return to Point A.
After your practice, turn off (A-B Repeat).
Repeat Playback
MIDI Audio
NOTE
AB
Top of the Song End of the Song
NOTE
Specifying the repeat range while Songs are stopped
1. Fast-forward the Song to Point A then turn on (A-B Repeat).
2. Fast-forward the Song to Point B then touch (A-B Repeat) again.
CVP-609/605 Owner’s Manual
65
Song Playback – Playing and Practice Songs
Like the Transpose function (page 38) of the MIDI Song, the pitch of an Audio Song in
the USB flash memory can be adjusted in semitone steps (from -12 to 12) on the Home
display.
1 Connect the USB flash memory containing Audio Songs to the [USB
TO DEVICE] terminal.
2 Select an Audio Song (steps 1 – 2 on page 57).
3 In the Song area (when expanded) of the Home display, touch
(Pitch Shift) to call up the Setup window.
4 Set the value by touching []/[].
Like Tempo adjustment of a MIDI Song (page 36), you can
adjust the playback speed of an Audio Song in USB flash
memory by stretching or compressing it.
To do this, select an Audio Song then touch (Time
Stretch) in the Song area of the Home display to call up the
Setup window. Touch []/[] in this window to set the value
(from 70% to 140%). Higher values result in a faster tempo.
You can cancel or attenuate the center position of the stereo
sound. This lets you sing “karaoke” style with just instrumental
backing, or play the melody part on the keyboard, since the
vocal sound is usually at the center of the stereo image in most
recordings.
To turn the Vocal Cancel function on/off, first select an Audio
Song, then turn on/off (Vocal Cancel) in the Song area
of the Home display.
Adjusting the Pitch in Semitones (Pitch Shift)
MIDI
Audio
NOTE
NOTE
Adjusting the Playback Speed (Time Stretch)
MIDI
Audio
NOTE
Canceling the Vocal Part (Vocal Cancel)
MIDI
Audio
NOTE
CVP-609/605 Owner’s Manual
66
Song Recording – Recording Your Performance –
Song Recording
– Recording Your Performance –
This instrument allows you to record your performance in the following two methods.
• MIDI recording
With this method, recorded performances are saved to the instrument or a USB flash memory as an SMF (format 0)
MIDI file. If you want to re-record a specific section or edit parameters such as Voice, use this method. Also if you want
to record your performance to each channel one by one, execute Multi Track Recording of the MIDI recording method.
Since a MIDI Song can be converted to an Audio Song after recording (page 70), you may want to use MIDI recording
(with overdubbing and multiple parts) to first create a complex arrangement you would not otherwise be able to play
live, then convert it to an Audio Song. This instrument allows you to record approximately 300 KB per Song.
• Audio recording
With this method, recorded performances are saved to a USB flash memory as an Audio file. Recording is done without
designating the recorded part. Since it is saved in stereo WAV format of normal CD quality resolution (44.1kHz/16bit)
by default, it can be transmitted to and played on portable music players by using a computer. The file format can be
changed to MP3 via [Menu] → [SongSetting] → [Rec] → [Audio Rec Format]. This instrument allows you to record up to
80 minutes per single recording.
Before recording, make the necessary settings such as Voice/Style selection (for MIDI
recording and Audio Recording) and the microphone connection (only for Audio
Recording, if you want to record your vocal). As necessary, connect the USB flash
memory to the [USB TO DEVICE] terminal, especially if you want to execute Audio
Recording.
1 On the Home display, touch [] at the upper right to expand the Song
area, then touch [ ] (Rec) to call up the Song Recording window.
Here and in the later steps, the operation in the Song area of the Home display can
be controlled by the SONG CONTROL buttons (page 59).
2 To u ch (MIDI Recording) or (Audio Recording).
A blank Song for recording is automatically set.
If you want to cancel recording, touch [Cancel] in the display or press the SONG
CONTROL [REC] button.
Basic Procedure for Recording (MIDI/Audio
Recording)
NOTE
Before starting Audio Recording:
Recorded data via Audio can only be saved to USB flash memory. If you want to execute Audio
Recording, make sure to connect the USB flash memory beforehand.
2
1
CVP-609/605 Owner’s Manual
67
Song Recording – Recording Your Performance –
3 Start Recording.
With MIDI Recording, you can start recording either by playing the keyboard or
touching [Rec Start]. With Audio Recording, start recording by touching [Rec
Start].
You can also start recording by pressing the SONG CONTROL [PLAY/PAUSE]
button.
4 Play the keyboard.
5 After you finish performance, touch [] (Stop) on the Home display to
stop recording.
6 To hear the recorded performance, touch [ / ] (Play/Pause).
7 Save the recorded performance.
In MIDI recording
After recording, (Save) appears in the Song area of the Home display. This icon
indicates that recorded data exists but has not yet been saved.
7-1 On the Home display, touch (Save) shown in the Song area.
The Song Selection display appears for selecting a destination to save the recorded
Song.
7-2 Save the recorded data as a file by following the instructions on page 29,
steps 2 – 5.
MIDI Songs can be saved to (User MIDI Song tab).
In Audio recording
Since the Audio Song file is automatically saved to the USB flash memory while
recording, the Save operation is not required. The recorded Audio Song will appear
in the (User Audio Song tab) on the Song Selection display. If
necessary, rename the file name by following the instructions on page 30.
3
6
5
NOTE
CVP-609/605 Owner’s Manual
68
Song Recording – Recording Your Performance –
With MIDI Recording, you can create a MIDI Song consisting of 16 channels by
recording your performance to each channel one by one. In recording a piano piece, for
example, you can record the right-hand part to channel 1 then record the left-hand part
to channel 2, allowing you create a complete piece which may be difficult to play live
with both hands together. To record a performance with Style playback, for example,
record the Style playback to channels 9 – 16, then record melodies to channel 1 while
listening to the already recorded Style playback. In this way, you can create an entire
Song which would otherwise be difficult, or even impossible, to play live.
1 If you want to re-record an existing MIDI Song, select the desired Song
(steps 1 – 2 on page 57).
If you want to record from scratch, skip this step.
2 On the Home display, touch [] at the upper right to expand the Song
area, then touch [ ] (Rec) to call up the Song Recording window.
When you re-record to an existing Song, the name of the Song selected in step 1
appears.
When you record from scratch, touch the [New MIDI] icon before going on to step
3. An empty Song is prepared and “New Song” appears.
Here and in the later steps, the operation in the Song area of the Home display can
be controlled by the SONG CONTROL buttons (page 59).
3 Tou ch [] at the left of “Channel” to expand the Channel area.
4 Specify the target channel and part for recording.
To specify a channel, touch and turn on the corresponding number. To turn the
channel number off, touch it again. To specify a part, touch the part icon of the
specified channel to call up the Part Selection window, then select the desired part.
Recording to Specified Channels (MIDI Recording)
3
2
NOTE
NOTE
Channel
Part
CVP-609/605 Owner’s Manual
69
Song Recording – Recording Your Performance –
To make the settings quickly, simply select the keyboard part ([Extra], [Left] or
[Right] located at the bottom left).
Right: This can be selected when recording only the right-hand part. The Main
part of the Voice will be recorded to channel 1, and the Layer part will be
recorded to channel 3.
Left: This can be selected when recording only the left-hand part. The Left part
of the Voice will be recorded to channel 2. When the Left part of the Voice is off,
the Main part will be recorded to channel 2 and the Layer part will be recorded to
channel 4.
Extra: This can be selected when recording only Style playback. The Style parts
will be recorded to channels 9 – 16.
5 Play the keyboard to start Recording.
You can also start recording by touching [Rec Start] or pressing the SONG
CONTROL [PLAY/PAUSE] button.
6 After you finish your performance, touch [] (Stop) on the Home
display to stop recording.
7 To hear the recorded performance, touch [ / ] (Play/Pause).
8 Record your performance to another Channel by repeating steps 2 – 7.
In step 4, select a Channel which has no recorded data. In step 5, play the keyboard
while listening to the already recorded data.
9 Save the recorded performance.
9-1 On the Home display, touch (Save) shown in the Song area.
The Song Selection display appears for selecting a destination to save the recorded
Song.
9-2 Save the recorded data as a file by following the instructions on page 29,
steps 2 – 5.
7
6
NOTE
CVP-609/605 Owner’s Manual
70
Song Recording – Recording Your Performance –
You can convert a recorded MIDI Song in the User memory or USB flash memory to an
Audio Song by playing back. Conversion is executed by playing back the MIDI Song and
re-recording it as an Audio Song. By default, the converted data is saved in WAV format,
in the same way as Audio recording (page 66).
1 Connect the USB flash memory (to which the Audio Song is to be
saved) to the [USB TO DEVICE] terminal.
2 Call up the Song Selection display which contains the MIDI Song to be
converted.
3 Touch [File] to call up the File Management icons.
4 Enter a checkmark to the MIDI Song to be converted.
5 Touch (Audio Convert) to call up the Song Selection display for
selecting the Save destination.
6 Specify the Save destination location.
You can add a new folder by touching (New Folder)
7 Touch [ConvertHere] to start conversion.
This operation starts playback and conversion from MIDI to audio. If you play the
keyboard or input audio signals via a microphone or the [AUX IN] jack during
conversion, the sound also will be recorded.
When conversion is completed, the message indicating that the conversion is being
executed will no longer be shown in the display, and the newly created new Audio
Song is shown in the Song Selection display.
Converting a MIDI Song to an Audio Song
NOTE
3 54
NOTE
CVP-609/605 Owner’s Manual
71
Microphone – Adding Vocal Harmony Effects to Your Singing –
Microphone
– Adding Vocal Harmony Effects to Your Singing –
By connecting a microphone to the [MIC./LINE IN] jack (standard 1/4" phone jack), you can enjoy singing along with
your keyboard performance or with Song playback. The instrument outputs your vocals through the built-in speakers.
Moreover, you can automatically apply various Vocal Harmony effects to your voice as you sing.
1 Before turning on the power of the instrument, set the [INPUT
VOLUME] knob to the minimum position.
2 Connect the microphone to the [MIC./LINE IN] jack.
3 Set the [LINE MIC] switch to “MIC.
4 Turn on the power of the instrument.
5 (If necessary, turn on the microphone.) Adjust the [INPUT VOLUME]
knob while singing into the microphone.
Adjust the control while checking the [MIC] lamp. Make sure to adjust the control
so the lamp lights in green. Make sure that the lamp does not light in red, since this
indicates that the input level is too high.
6 On the Balance display ([Menu] → [Balance]), adjust the volume
balance between the microphone sound and the instrument sound
(page 38).
Connecting a Microphone
NOTE
MIN MA X
INPUT
MIC.
MIC. LINE PHONES
VOLUME
LINE IN
MIN MA X
INPUT
MIC.
MIC. LINE PHONES
VOLUME
LINE IN
32
CVP-609/605 Owner’s Manual
72
Microphone – Adding Vocal Harmony Effects to Your Singing –
The Vocal Harmony feature lets you add harmonies to your vocal input via the
microphone sound.
1 Connect the microphone to the instrument (page 71).
2 Call up the Vocal Harmony display via [Menu] → [VocalHarmony].
3 Make sure that Harmony is set to “On.
4 Touch the Vocal Harmony name to call up the Vocal Harmony Selection
display.
5 Select a Vocal Harmony type.
The Vocal Harmony features three different Modes which can be selected
automatically by selecting a Vocal Harmony type.
Harmony mode
Disconnecting the microphone
1. Set the [INPUT VOLUME] knob to the minimum position.
2. Disconnect the microphone from the [MIC./LINE IN] jack.
NOTE
Applying Vocal Harmony Effects to Your Voice
4
3
6-1
Vocal Harmony name
Mode
(When the Mode is set to “Vocoder” or “Vocoder Mono”)
NOTE
Chordal
The harmony notes are determined by the chords you play in the
chord section (with [ACMP ON/OFF] turned on), the left hand
section (with [ACMP ON/OFF] turned off and the Left part turned
on) or chord data of Song.
Vo co der
The microphone sound is output via the notes you play on the
keyboard or the Song playback notes.
Vo co der-Mono
(only for CVP-609)
Same as the Vocoder basically. In this mode, only single-note
melodies or lines can be played back (with last-note priority).
Auto (Vocoder/
Chordal)
(only for CVP-605)
When the [ACMP ON/OFF] or Left part is turned on, or a Song
contain chord data is being played back, the mode is automatically
set to “Chordal.” In all other cases, the mode is set to “Vocoder.
CVP-609/605 Owner’s Manual
73
Microphone – Adding Vocal Harmony Effects to Your Singing –
6 Follow the steps below, depending on which Type (and mode) you
selected.
If you selected the Chordal Type:
6-1 Make sure that the [ACMP ON/OFF] button is turned on.
6-2 Play back a Style, or play back a Song which contains chords.
Vocal harmonies based on the chords are applied to your singing.
If you selected the Vocoder or Vocoder-Mono Type:
6-1 As necessary, change the “Keyboard” setting to “Off,” “Upper,” or “Lower.
When “Upper” or “Lower” is selected, playing the right-hand or left-hand section of the
keyboard will control the Vocoder effect. When “Off is selected, playing the keyboard
will not control the Vocoder effect.
6-2 Play melodies on the keyboard or play back a Song, and sing into the
microphone.
You’ll notice that you don’t actually have to sing pitched notes. The Vocoder effect takes
the words you say and applies them to the pitch of the instrument sounds.
Using the Talk Function
This function lets you instantly change the microphone settings for
talking or making announcements between song performances.
To call up the Talk setting, touch [Talk] located at the left on the Vocal
Harmony display. To recall the Vocal Harmony settings, touch [Vocal]
and turn it on.
Useful functions for Karaoke
Lyrics on the display ......................page 61
Transpose, Pitch Shift ....................pages 38, 65
Vocal Cancel ...................................page 65
NOTE
CVP-609/605 Owner’s Manual
74
Music Finder – Calling up Ideal Panel Setups for Your Performance –
Music Finder
– Calling up Ideal Panel Setups for Your Performance –
This feature lets you call up panel settings ideal for your performance simply by selecting a “Record,” which includes
Voice and Style settings. If you want to play a certain piece of music but don't know which Style and Voice settings
would be appropriate, you can search for relevant Records by the title of the piece.
Moreover, by registering Song and Style files saved in various locations into Music Finder, the instrument can easily call
up the desired Song or Style file from the corresponding Record.
Downloading Records (panel settings) from the website
As a factory default, some sample Records (panel settings) are provided in the Music Finder. To
use the Music Finder function more conveniently and effectively, we recommend that you
download the Records (panel settings) from the Yamaha website, and load them to this
instrument.
1 On the computer, access the following website and download the Music
Finder file (***.mfd) to the USB flash memory connected to the computer.
http://download.yamaha.com/
2 Connect the USB flash memory containing the Music Finder file (***.mfd) to
the [USB TO DEVICE] terminal of this instrument.
3 Call up the Music Finder display via [Menu] → [MusicFinder].
4 Touch (Load) to call up the File Selection display.
5 Select the desired Music Finder file in the USB flash memory to call up a
message prompting you to select “Replace” or “Append.
6 Touch [Append] if you want to add Records of the selected Music Finder file,
or touch [Replace] if you want to replace all Records with the new ones.
7 Touch [Yes] in response to the confirmation message.
4
NOTE
CVP-609/605 Owner’s Manual
75
Music Finder – Calling up Ideal Panel Setups for Your Performance –
1 Call up the Music Finder display via [Menu] → [MusicFinder].
2 Touch the desired Record.
The panel settings in the Record are called up. When the Record including the
Style name is selected, ACMP and SYNC START are turned on and the
corresponding Style is called up. This lets you start Style playback immediately.
If searching for the desired Record is difficult, use the Sort function described
below.
3 Play the Style by specifying the chords with your left hand and play the
melody with your right.
Selecting the Desired Record (Panel Settings)
Sorting the Records
Touch one of the Sorting tabs to sort the Records in the corresponding order. Touch the
same tab to alternate the order, ascending or descending.
•Music
Sorts the Records title of the music piece.
•Style
Sorts the Records by Style name.
•Beat
Sorts the Records by beat.
(Tempo)
Sorts the Records by tempo.
(Favorite)
Touching here shows only the Favorite Records. To show all the Records, touch here again. To add a
Record to Favorite, touch the star mark ( ) of the desired Record to make it colored ( ).
To delete it from Favorite, touch the colored star mark ( ).
Sorting tab
NOTE
CVP-609/605 Owner’s Manual
76
Music Finder – Calling up Ideal Panel Setups for Your Performance –
You can also search for Records by specifying a song title or keyword, using the Search
function of Music Finder.
1 Call up the Music Finder display via [Menu] → [MusicFinder].
2 Touch the Search box to call up the Character Entry window.
3 Enter the keyword for searching (page 33) to start Search.
If you want to input two or more keywords, insert a space between each word.
After the Search is completed, the resulting Record list appears. If no Records are
listed, try this step again with another keyword.
4 Select the desired Record.
To clear the result and show all Records in the Music Finder, touch [×] in the
Search box.
5 Play the Style by specifying the chords with your left hand and playing
the melody with your right.
Searching for Records (Panel Settings)
2
Search box
CVP-609/605 Owner’s Manual
77
Music Finder – Calling up Ideal Panel Setups for Your Performance –
By registering Song or Style files in various locations (Preset, User and USB) into Music
Finder, you can easily call up your favorite files.
1 In the Song or Style Selection display, select the desired file.
2 Touch (Add) to call up the Create Record display.
As necessary, you can change the Music title and keyword, etc. For details about the
Create Record display, refer to the Reference Manual on the website.
3 Touch [Create] to create a new Record to which the Song or Style
selected in step 1 is registered.
4 Check that the created Record is shown in the Music Finder display.
In the “Style” column of the Record to which the Song is registered, “(MIDI Song)”
or “(Audio Song)” is shown.
Calling up the Song or Style registered to Music Finder
You can call up the registered Song or Style in the same way as done in the sections
Selecting the Desired Record” (page 75) and “Searching for Records” (page 76).
Registering a Song or Style to a Record
NOTE
2
NOTE
NOTE
CVP-609/605 Owner’s Manual
78
Registration Memory – Saving and Recalling Custom Panel Setups –
Registration Memory
– Saving and Recalling Custom Panel Setups –
The Registration Memory function allows you to save (or “register”) virtually all panel settings to a Registration
Memory button, and then instantly recall your custom panel settings by simply pressing a single button. The registered
settings for eight Registration Memory buttons should be saved as a single Bank (file).
1 Set up the panel controls (such as Voice, Style and so on) as desired.
Refer to the separate Data List for a list of parameters that can be registered with
the Registration Memory function.
2 Press the [MEMORY] button in the REGISTRATION MEMORY
section to call up the Registration Memory window.
3 Press one of the REGISTRATION MEMORY [1] – [8] buttons to which
you wish to memorize the panel setup.
The memorized button becomes red, indicating that the number button contains
data and its number is selected.
4 Register various panel setups to other buttons by repeating steps 1 – 3.
The registered panel setups can be recalled by simply pressing the desired number
button.
Registering Your Panel Setups
Selecting the items to be registered
Touching [] at the bottom left of the window calls up the list for selecting the items to be
registered. Before going on to step 3, enter or remove checkmarks by touching the desired
items. Items having checkmarks will be registered.
Displays or hides the list of items
About the lamp status
Red: Data registered and currently selected
Green: Data registered but not currently selected
Off: No data registered
NOTE
CVP-609/605 Owner’s Manual
79
Registration Memory – Saving and Recalling Custom Panel Setups –
You can save all eight registered panel setups as a single Registration Memory Bank file.
1 On the Home display, touch [] at the upper right corner to show the
Registration area, then touch the area to call up the Registration Bank
Selection display.
This display can be called up also by pressing the REGIST BANK [+] and [-]
buttons simultaneously.
2 Touch (Save) to save the Bank file.
For instructions on saving, refer to page 29.
Saving the Registration Memory as a Bank File
Bank 01
Bank 02
Bank 03
Bank 04
2
1
NOTE
CVP-609/605 Owner’s Manual
80
Registration Memory – Saving and Recalling Custom Panel Setups –
The saved Registration Memory Bank files can be recalled by using the REGIST BANK
[-]/[+] buttons or the following procedure.
1 Call up the Registration Bank Selection display (step 1 on page 79).
2 Touch and select the desired Bank on the display.
You can also use the REGIST BANK [-]/[+] buttons to select a Bank.
3 Press one of the green-lit numbered buttons ([1] – [8]) in the
Registration Memory section.
Confirming the Registration Memory Information
You can call up the information display to confirm which Voices and Style are
memorized to the [1] – [8] buttons of a Registration Memory Bank.
1 Call up the Registration Bank Selection display, then select the desired
Bank.
2 Touch (Information) to call up the Registration Information
window.
This display consists of two pages: Voice-related and Style-related. You can
alternate between the two via []/[].
To change the name of the selected Registration, touch (Rename). To delete the
selected Registration, touch (Delete).
Recalling a Registered Panel Setup
NOTE
For switching the
pages.
NOTE
Naming the Registration Memory data
If you have created a wide variety of Registration Setups, it may be difficult to find the one
desired for your particular live performance situation.
To remedy this, it is good idea to assign names to both the Registration Memory Bank and its
Registration Setups individually.
CVP-609/605 Owner’s Manual
81
Mixer – Editing the Volume and Tonal Balance –
Mixer
– Editing the Volume and Tonal Balance –
The Mixer gives you intuitive control over aspects of the keyboard parts and Song/Style channels, including volume
balance and the timbre of the sounds. It lets you adjust the levels and stereo position (pan) of each Voice to set the
optimum balance and stereo image, and lets you set how the effects are applied.
1 Call up the Mixer display via [Menu] → [Mixer].
2 Touch a tab for editing the balance between the desired parts.
Basic Procedure for the Mixer
Panel
Use this display when you want to adjust the balance between the
entire Song part, entire Style part, Mic part, Main part, Layer part
and Left part.
Style
Use this display when you want to adjust the balance between all the
parts of the Style.
•Rhythm1, Rhythm2
These are the basic parts of the Style, containing the drum and percussion
rhythm patterns.
•Bass
The bass part uses various appropriate instrument sounds to match the
Style.
•Chord1, Chord2
These comprise the rhythmic chord backing, commonly consisting of piano
or guitar Voices.
•Pad
This part is used for sustained instruments such as strings, organ, choir, etc.
•Phrase1, Phrase2
These parts are used for punchy brass stabs, arpeggiated chords, and other
extras that make the accompaniment more interesting.
Song Ch1-8 /
9-16
Use this display when you want to adjust the balance between all the
parts of the MIDI Song. This is available only when a MIDI Song is
selected.
Master
Unlike the other displays, use this display when you want to adjust
the tonal characteristics of the entire sound (except for Audio
Songs) of this instrument.
2
3
CVP-609/605 Owner’s Manual
82
Mixer – Editing the Volume and Tonal Balance
3 Touch a tab for editing the desired parameters.
When a tab other thanMaster” is selected in step 2:
When “Master” is selected in step 2:
4 Set the value of each parameter.
5 Save your Mixer settings.
To save the Panel display settings:
Register them to Registration Memory (page 78).
To save th e Sty le disp lay s ettings:
Save them as a Style file to the User memory or USB flash memory. If you want to
recall the settings for future use, select the Style file saved here.
1. Call up the operation display via [Menu] → [StyleCreator].
2. Touch (Save) to call up the Style Selection display, then save as a Style file
(page 29).
To save the Song Ch 1-8/9-16 display settings:
First register the edited settings as part of the Song data (Setup), then save the Song
to the User memory or USB flash memory. If you want to recall the settings for
future use, select the Song file saved here.
1. Call up the operation display via [Menu] → [SongCreator] → [Channel Edit].
2. Touch [Setup].
3. Touch [Execute] to execute the Setup.
4. Touch (Save) to call up the Song Selection display, then save as a Song file
(page 29).
Filter
Adjusts the Harmonic Content (resonance) and sound brightness.
EQ
Adjusts equalization parameters to correct the tone or timbre of the
sound.
Effect
Selects an Effect type and adjusts its depth for each part.
Chorus/Reverb
Selects a Chorus/Reverb type and adjusts its depth for each part.
Pan/Volume
Adjusts panning and volume for each part
Compressor
(only for CVP-
609)
Lets you turn the Master Compressor (which is applied to the entire
sound) on or off, select the Master Compressor type, and edit the
related parameters. Your original edits can be saved as the Master
Compressor type.
EQ
Lets you select the Master EQ type applied to the entire sound and
edit the related parameters. Your original edits can be saved as the
Master EQ type.
NOTE
CVP-609/605 Owner’s Manual
83
Mixer – Editing the Volume and Tonal Balance –
To store the Master display settings:
Your original edits can be stored as a Master Compressor type and Master EQ type.
Up to five types can be stored respectively. To call one of these up in the future,
select the corresponding type at the upper right of each display.
1. Touch (Save) in the “Compressor” display or “EQ” display.
2. Select one of USER1 – USER5 then touch [Save] to call up the Character Entry
window.
3. On the Character Entry window, change the name as necessary, then touch
[OK] to save the data.
The Mixer display lets you turn each channel of the current Style or Song on or off.
1 In the Mixer display, touch the [Style] tab, [Song Ch 1-8] tab or [Song
Ch 9-16] tab.
2 Touch the Channel which you want to turn on or off.
If you want to solo a specific channel, touch and hold the desired channel until the
number turns green. To cancel solo, simply touch the (green) channel number
again.
3 As necessary, make other settings then save them as a Style file or Song
file (step 5 on page 82).
Turning Each Channel of the Style or Song On/Off
To change the Voice for each channel:
Touch the instrument icon below the channel number to call up the Voice Selection
display, then select the desired Voice.
Channel
Voice
CVP-609/605 Owner’s Manual
84
Connections – Using Your Instrument with Other Devices –
Connections
– Using Your Instrument with Other Devices –
CVP-609
CVP-605
CVP-609/605
I/O Connectors
NOTE
[AUX PEDAL] jack ................page 87
MIDI terminals......................page 90
[USB TO HOST] terminal.....page 90
[USB TO DEVICE] terminal.page 88
[VIDEO OUT] jack................page 86
[RGB OUT] terminal
(only for CVP-609) ................page 86
[AUX IN] jack ........................page 85
AUX OUT [L/L+R]/[R] jacks page 85
[INPUT VOLUME] knob ......page 71
[MIC./LINE IN] jack .............page 87
[MIC. LINE] switch ...............page 71
[PHONES] jacks ....................page 19
Right
(higher-key side)
Left (lower-key side)
Front (keyboard side)
Right
(higher-key side)
Left (lower-key side)
Front (keyboard side)
MIN MAX
INPUT
MIC.
MIC. LINE PHONES
VOLUME
LINE IN
CAUTION
CVP-609/605 Owner’s Manual
85
Connections – Using Your Instrument with Other Devices –
Playing a Portable Audio Player with the Built-in Speakers
You can connect the headphone jack of a portable audio player to the instrument’s [AUX
IN] jack, letting you hear the sound of that audio player through the built-in speakers of
the instrument.
Using an External Stereo System for Playback
You can connect a stereo system to amplify the instrument’s sound by using the AUX
OUT [L/L+R]/[R] jacks. The microphone or guitar sound connected to the instrument’s
[MIC./LINE IN] jack is output at the same time.
Connecting Audio Devices ([AUX IN] jack, AUX
OUT [L/L+R]/[R] jacks)
NOTE
NOTE
NOTE
Minimizing noise of the input sound via Noise Gate
By default, this instrument cuts unwanted noise from the input sound. However, this may
result in wanted sounds also being cut, such as the soft decay sound of the piano. To avoid this,
set the Noise Gate to off via [Menu] → [Utility] → [Speaker/Connectivity] → [AUX In Noise
Gate].
Instrument Portable audio player
Headphone jack
Phone plug
(stereo mini)
Phone plug
(stereo mini)
Audio cable
Audio signal
Instrument Powered speaker
Audio cable
Audio signal
Phone plug
(standard)
Phone plug
(standard)
Input jack
CVP-609/605 Owner’s Manual
86
Connections – Using Your Instrument with Other Devices –
By connecting with an external monitor such as a television to the [VIDEO OUT] jack
of the instrument, the lyrics and text on the instrument's display can be shown on the
television or the monitor. On the CVP-609, the instrument can be connected with an
external monitor also by the [RGB OUT] terminal.
Screen Out Settings
1 Call up the operation display via [Menu] → [Utility] → [Speaker/
Connectivity].
2 Set the monitor type and screen contents.
Connecting an External Monitor ([VIDEO OUT]
jack, [RGB OUT] terminal)
CAUTION
Monitor
Type
Selects the desired output monitor type (NTSC or PAL) to correspond to
the standard used by your video equipment.
CVP-609 only: Select “RGB” when connecting to an external monitor.
Content
Determines the contents of the Video Out signal.
Lyrics/Text: Only the lyrics of the Song or text files (whichever you
used last time) are output, regardless of the display that is called up on
the instrument.
LCD: The currently selected display is output.
(CVP-609 only)
RCA pin plug
VIDEO IN
Mini D-sub 15-pin
Video cable
Instrument
NOTE
CVP-609/605 Owner’s Manual
87
Connections – Using Your Instrument with Other Devices –
Optional footswitches (Yamaha FC4 or FC5) and an optional Foot controller (Yamaha
FC7) can be connected to the [AUX PEDAL] jack. A footswitch can be used for
switching functions on and off, while a foot controller controls continuous parameter
such as volume.
Example 1: Using a foot controller to control the volume of the
performance data played on the keyboard.
Connect the FC7 foot controller to the [AUX PEDAL] jack. With the initial factory
settings, no special setup is necessary.
Example 2: Using a footswitch to control Song Start/Stop.
Connect a footswitch (FC4 or FC5) to the [AUX PEDAL] jack.
To assign the function to the connected pedal, select “Song Play/Pause” in the operation
display: [Menu] → [Assignable] → [Pedal].
To the [MIC./LINE IN] jack (standard 1/4" phone jack), you can connect a microphone,
guitar, or other various equipment. For instructions on connecting a microphone, refer
to page 71.
Note that you need to select “MIC” or “LINE IN” depending on the connected
equipment. When the output level of the connected equipment (such as a microphone,
guitar, bass) is low, set the [MIC. LINE] switch to “MIC.” When the output level of the
connected equipment (such as a synthesizer, keyboard, CD player) is high, set the [MIC.
LINE] switch to “LINE.
Connecting a Footswitch/Foot Controller ([AUX
PEDAL] jack)
NOTE
Connecting a Microphone or Guitar ([MIC./LINE
IN] jack)
Foot Pedals
Footswitch FC4
(optional)
Footswitch FC5
(optional)
Foot Controller FC7
(optional)
CVP-609/605 Owner’s Manual88
Connections – Using Your Instrument with Other Devices –
You can connect a USB flash memory or a USB wireless LAN adaptor to the [USB TO DEVICE] terminal. You can save
data you’ve created on the instrument to the USB flash memory (page 29), or you can connect the instrument to a
smart device such as iPad via wireless LAN (page 89).
Connecting USB Devices ([USB TO DEVICE] terminal)
Precautions when using the [USB TO DEVICE]
terminal
When connecting a USB device to the terminal, be sure to
handle the USB device with care. Follow the important
precautions below.
NOTE
For more information about the handling of USB devices,
refer to the owner’s manual of the USB device.
Compatible USB devices
•USB flash memory
USB wireless adaptor (which is included only in some
areas)
The instrument does not necessarily support all
commercially available USB devices. Yamaha cannot
guarantee operation of USB devices that you purchase.
Before purchasing a USB device for use with this
instrument, please visit the following web page:
http://download.yamaha.com/
NOTE
Other USB devices such as a computer keyboard or mouse
cannot be used.
Connecting a USB device
When connecting a USB device to the [USB TO DEVICE]
terminal, make sure that the connector on the device is
appropriate and that it is connected in the proper direction.
NOTICE
When connecting a USB device to the [USB TO DEVICE]
terminal on the top panel, remove it before closing the
key cover. If the key cover is closed with the USB device
connected, the USB device may be damaged.
Avoid connecting or disconnecting the USB device
during playback/recording, file management (such as
Save, Copy, Delete and Format operations) or when
accessing the USB device. Failure to do so may result
in “freezing” of the operation of the instrument or
corruption of the USB device and the data.
When connecting then disconnecting the USB device
(and vice versa), make sure to wait a few seconds
between the two operations.
NOTE
When connecting a USB cable, make sure that the length is
less than 3 meters.
Using USB Flash Memories
By connecting the instrument to a USB flash memory, you
can save data you’ve created to the connected USB flash
memory, as well as read data from the connected USB flash
memory.
Maximum number of USB flash memory devices
Up to two USB flash memory devices can be connected to
the [USB TO DEVICE] terminal.
Formatting USB flash memory
Yamaha recommends that you format the USB flash
memory with this instrument (page 89). USB flash memory
formatted on another device may not operate properly.
NOTICE
The Format operation deletes any previously existing
data. Make sure that the USB flash memory you are
formatting does not contain important data. Proceed with
caution, especially when connecting multiple USB flash
memories.
To protect your data (write-protect)
To prevent important data from being inadvertently erased,
apply the write-protect provided with each USB flash
memory. If you are saving data to the USB flash memory,
make sure to disable write-protect.
Turning off the instrument
When turning off the instrument, make sure that the
instrument is NOT accessing the USB flash memory by
playback/recording or file management (such as during
Save, Copy, Delete and Format operations). Failure to do so
may corrupt the USB flash memory and the data.
CVP-609/605 Owner’s Manual
89
Connections – Using Your Instrument with Other Devices –
Formatting a USB Flash Memory
When a USB flash memory is connected or media is inserted, a message appears
indicating that the connected USB flash memory is not formatted. If so, execute the
format operation.
1 Connect a USB flash memory for formatting to the [USB TO DEVICE]
terminal.
2 Call up the operation display via [Menu] → [Utility] → [USB Memory].
3 Touch the USB flash memory to be formatted from the device list.
The indications USB 1, USB 2, etc. are displayed depending on the number of the
connected devices.
4 Touch [Format] to execute the Format operation.
You can connect a smart device such as an iPhone or iPad to the [USB TO DEVICE]
terminal of the instrument via the USB wireless LAN adaptor (if included). The USB
wireless LAN adaptor may not be included depending on your locale due to local
regulations. If the USB wireless LAN adaptor is not supplied with your instrument,
connect the smart device to the [USB TO HOST] terminal via the Yamaha i-UX1
(optional) or to the MIDI terminals via the Yamaha i-MX1 (optional). By using an
application tool on your smart device, you can take advantage of convenient functions
and get more enjoyment out of this instrument.
For details on connections, refer to the “iPhone/iPad Connection Manual” on the
website.
For information about the compatible smart devices and application tools, access the
following page:
http://www.yamaha.com/kbdapps/
For inquiries about the included USB wireless LAN adaptor, contact your nearest
Yamaha representative or the distributor listed at the end of this manual, and not the
devices manufacturer.
Or you can access the following website and contact Yamaha support at your location.
http://www.yamaha.com/contact/
Yamaha does not guarantee or support use of the included USB wireless LAN adaptor
with any devices other than this instrument.
Connecting to an iPhone/iPad ([USB TO DEVICE]
terminal, [USB TO HOST] terminal and MIDI terminals)
4
NOTE
CVP-609/605 Owner’s Manual
90
Connections – Using Your Instrument with Other Devices –
By connecting a computer to the [USB TO HOST] terminal, you can transfer data
between the instrument and the computer via MIDI.
For details on using a computer with this instrument, refer to the “Computer-related
Operations” on the website.
Use the MIDI [IN]/[OUT]/[THRU] terminals and standard MIDI cables to connect
external MIDI devices (keyboard, sequencer, etc.).
MIDI IN
Receives MIDI messages from another MIDI device.
MIDI OUT
Transmits MIDI messages generated by the instrument to another MIDI device.
MIDI THRU
Simply relays the MIDI messages received at MIDI IN.
The MIDI settings such as transmit/receive channels on the instrument can be set via
[Menu] → [MIDI]. For details, refer to the Reference Manual on the website.
Connecting to a Computer ([USB TO HOST]
terminal)
NOTE
Connecting External MIDI Devices (MIDI
terminals)
ComputerInstrument
USB cable
External MIDI deviceInstrument
MIDI reception
MIDI OUT MIDI INMIDI OUTMIDI IN
MIDI transmission
NOTE
CVP-609/605 Owner’s Manual 91
Menu Display Function List
Menu Display Function List
This section explains simply and very briefly explains what you can do in the displays which are called up by touching
each icon on the Menu display. Some functions are described in this Owner’s Manual on the pages indicated below. For
details about each function, refer to the Reference Manual on the website.
Menu Description Pages
Tempo
Adjusts the tempo of MIDI Song, Style or Metronome. The same operation
as using Tempo [-]/[+] and [Tap] buttons can be done on the display.
36
Transpose
Transposes the pitch of the entire sound in semitones, or just the sound of
the keyboard or MIDI Song.
38
Split Point & Fingering Type
Lets you set the Split Point or change the Chord Fingering type. 45, 55
Chord Tutor
Shows you an example of how to play a chord that corresponds to the
specified chord name.
Balance
Adjusts the volume balance among the keyboard parts (Main, Layer, Left),
Style, Song and microphone sound.
38
Mixer
Filter
Adjusts the Harmonic Content (resonance) and sound brightness.
81
EQ
Adjusts equalization parameters to correct the tone or timbre of the sound.
Effect
Selects an Effect type and adjusts its depth for each part.
Chorus/Reverb
Selects a Chorus/Reverb type and adjusts its depth for each part.
Pan/Volume
Adjusts panning and volume for each part.
(Master)
Compressor
Lets you turn on/off the Master Compressor, and edit related parameters.
(Master) EQ
Lets you edit the Master EQ.
Score
Displays the music notation (score) of the current MIDI Song. 60
Lyrics
Displays the lyrics of the current MIDI Song. 61
Text Viewer
Displays text files created on your computer. 62
Keyboard Harmony
Adds the Harmony effect to the right-hand section of the keyboard.
Parameters such as Harmony type can be set.
Mic Setting
Makes settings for the microphone sound.
Vocal Harmony
Adds Vocal Harmony effects to your singing. You can edit the Vocal
Harmony and save as your original harmony.
72
Music Finder
Calls up ideal panel settings (as a Record) for your performance. Records
can be created or edited.
74
Registration Sequence
Determines the order for calling up Registration Memory settings when
using the pedal.
Registration Freeze
Selects the item(s) to be unchanged even when you call up panel setups
from the Registration Memory.
Assignable
Pedal
Determines the functions assigned to the pedals.
Assignable
Determines the functions assigned to the ASSIGNABLE [1] – [4] buttons. 28
Voice Edit
Lets you edit the preset Voices to create your own Voices. The display
differs depending on whether an Organ Flutes Voice or another kind of
Voice is selected.
47
Style Creator
Lets you create a Style by editing the preset Style, or by recording Style
channels one by one.
CVP-609/605 Owner’s Manual
92
Menu Display Function List
Song Creator
Lets you create a Song by editing the recorded Song.
Voice
Setting
Tune
Adjusts the pitch for each keyboard part (Main/Layer/Left).
Piano
Edits the parameters for the piano Voices.
Voice Set
Determines which settings (effects, etc.) linked to the Voices are not called
up when selecting a Voice.
Setting
Determines how the Voice Selection display is opened when one of the
VOICE category buttons is pressed. Also determines whether to add
articulation effects or not when selecting an SA2 Voice (CVP-609 only).
Style
Setting
Setting
Edits parameters for Style playback such as Stop Accompaniment and OTS
Link Timing.
Change
Behavior
Determines the Style condition (sections, tempo, etc.) when selecting a
different Style.
Song
Setting
Guide
Selects the type of the Guide function, or changes the guide lamp settings.
Part Ch
Determines which MIDI channel in the Song data is used for the right-hand/
left-hand part.
Lyrics
Determines the language of the displayed lyrics.
Play
Edits parameters for Song playback such as Repeat Playback and the
Performance Assistant Technology.
Rec
Edits parameters for re-recording of MIDI Songs, or determines the file
format for Audio recording.
Tuning
Master Tune
Fine-tunes the pitch of the entire instrument in approx. 0.2 Hz steps.
Scale Tune
Selects the scale type and tunes the pitch of the desired note (key) in cents.
Keyboard Setting
Determines the Touch Response of the keyboard, or turns the Left Hold
function on/off.
37
Metronome
Setting
Metronome
Determines the metronome volume, sound and time signature.
Tap Tempo
Determines the volume and sound type of the sound caused when the [TAP]
button is pressed.
MIDI Setting
System
Edits the parameters for MIDI system messages.
Transmit
Edits the parameters for MIDI transmission.
Receive
Edits the parameters for MIDI reception.
On Bass Note
Determines the bass note for Style playback based on the note messages
received via MIDI.
Chord Detect
Determines the chord type for Style playback based on the note messages
received via MIDI.
Utility
Speaker/
Connectivity
Makes the settings for the instrument’s speakers and the external monitor. 86
Display
Edits the parameters for the display settings, such as touch panel
calibration.
Parameter Lock
Determines which parameters (effect, split point, etc.) will not be changed
when the panel setups are changed via Registration Memory.
USB Memory
Indicates the capacity of the connected USB flash memory or allows you to
format it.
89
System
Indicates the firmware version of this instrument, or lets you make basic
settings such as language for the display.
16
Factory Reset/
Backup
Initializes the instrument to the factory default, or backs up the data stored
in the instrument.
39
Wireless LAN Setting
Makes settings for connecting the instrument to a smart device such as
iPad via wireless LAN. This icon appears only when the USB wireless
adaptor (if included) has been connected once.
Menu Description Pages
CVP-609/605 Owner’s Manual
93
CVP-609 (Grand piano type) Assembly
CVP-609 (Grand piano type) Assembly
CAUTION
Assemble the unit on a hard and flat floor with ample space.
Be careful not to confuse or misplace the parts, and be sure to
install all parts in the correct orientation. Please assemble the
unit in accordance with the sequence described here.
Assembly should be carried out by at least two persons.
Be sure to use only the included screws of the specified sizes.
Do not use any other screws. Use of incorrect screws can cause
damage or malfunction of the product.
Be sure to tighten all screws upon completing assembly of each
unit.
To disassemble the unit, reverse the assembly sequence.
1 Remove all parts from the package and
make sure you have all of the items.
How to position the main unit
CAUTION
Be careful not to pinch your fingers.
Spread a large soft cloth, such as a blanket, on the floor. Place
the unit on the cloth with the key cover closed and the
keyboard side on the bottom and lean the unit against the wall
so that the unit will not fall or slip.
Place a soft cloth against the wall to protect the instrument and
the wall from scratches.
Have a Phillips-head (+) screwdriver of the appropriate size ready.
Pedal box
Power cord
Legs
6 x 20 mm fixing screws (4)
Cord holder
6 x 40 mm fixing screws (12)
Headphone hanger
4 x 10 mm
thin screws (2)
To prevent the key cover from accidentally opening during assembly,
press down on the key cover, making sure that the sheets (shown)
remain in place.
To prevent damage to the instrument, do not lay the unit on the floor
directly. Lean the unit against the wall as shown in the “How to
position the main unit” section.
Main unit
NOTICE
Do not place the main unit as shown in the illustration here.
Be sure to position the keyboard side
on the bottom.
Incorrect
Incorrect
Incorrect
CVP-609/605 Owner’s Manual
94
CVP-609 (Grand piano type) Assembly
2 Attach two front legs and a rear leg.
Refer to the diagram below to verify the orientation of the
legs.
Install and tighten four screws on each leg, starting with
one of the front legs.
3 Install the pedal box.
Remove the twist tie that affixes the pedal cord to the upper
portion of the pedal box.
Align the cord with the groove on the unit, and attach the
pedal box using four screws.
Insert the pedal cord plug into the pedal connector.
Insert the plug into the connector so that the side with the
arrow mark is facing forward (keyboard side). If the plug
does not fit easily do not try to force it, but check the plug
for correct orientation, and then reinsert it into the
connector.
Insert the pedal cord securely until the metal part of the
cord plug disappears from view. Otherwise, the pedal may
not function properly.
Attach the cord holder on the unit as shown in the
illustration below, then use the cord holder to affix the
pedal cord.
4 Raise the unit to the standing position.
Use the front legs as support to raise the unit.
CAUTION
Be careful not to pinch your fingers.
When you raise the unit, do not hold the key cover.
.
Rear leg
Front leg Front leg
6 x 40 mm fixing screws
Twist tie
6 x 20 mm fixing screws
CVP-609/605 Owner’s Manual
95
CVP-609 (Grand piano type) Assembly
5 Plug the power cord into the power
connector.
6 Rotate the adjuster until it comes in firm
contact with the floor surface.
7 Attach the headphone hanger.
Attach the headphone hanger using two thin screws (4 x
10 mm) as shown in the illustration.
Voltage Selector
Before connecting the AC power cord, check the setting of the
voltage selector which is provided in some areas. To set the selector
for 110V, 127V, 220V or 240V main voltages, use a “minus
screwdriver to rotate the selector dial so that the correct voltage for
your region appears next to the pointer on the panel. The voltage
selector is set at 240V when the unit is initially shipped. After the
proper voltage has been selected, connect the AC power cord to the
AC IN jack and an AC wall outlet. A plug adaptor may be also
provided in some areas to match the pin configuration of the AC
wall outlets in your area.
WARNING
An improper voltage setting can cause serious damage to
the instrument or result in improper operation.
Right leg on the bottom of the main unit,
when viewed from front
For models that feature a
voltage selector:
Set the voltage selector to an
appropriate voltage.
After completing the assembly, please check the following.
•Are there any parts left over?
→ Review the assembly procedure and correct any errors.
Is the Clavinova clear of doors and other movable
fixtures?
→ Move the Clavinova to an appropriate location.
Does the Clavinova make a rattling noise when you
shake it?
→ Tighten all screws.
Does the pedal box rattle or give way when you step on
the pedals?
→ Turn the adjuster so that it is set firmly against the floor.
Are the pedal and power cords inserted securely into
the sockets?
CAUTION
When moving the instrument, always hold the bottom of the
main unit. Do not hold the key cover or top portion. Improper
handling can result in damage to the instrument or personal
injury.
Transp orting
If you move to another location, you can transport the instrument
along with other belongings. You can move the unit as it is
(assembled) or you can disassemble the unit down to the condition
it was in when you first took it out of the box. Transport the
keyboard horizontally. Do not lean it up against a wall or stand it up
on its side. Do not subject the instrument to excessive vibration or
shock. When transporting the assembled instrument, make sure all
screws are properly tightened and have not been loosened by
moving the instrument.
CAUTION
If the unit creaks or is otherwise unsteady when you play on
the keyboard, refer to the assembly diagrams and retighten
all screws.
Do not hold
here.
Do not hold here.
CVP-609/605 Owner’s Manual
96
CVP-609 Assembly
CVP-609 Assembly
CAUTION
Assemble the unit on a hard and flat floor with ample space.
Be careful not to confuse or misplace the parts, and be sure to
install all parts in the correct orientation. Please assemble the
unit in accordance with the sequence described here.
Assembly should be carried out by at least two persons.
Be sure to use only the included screws of the specified sizes.
Do not use any other screws. Use of incorrect screws can cause
damage or malfunction of the product.
Be sure to tighten all screws upon completing assembly of each
unit.
To disassemble the unit, reverse the assembly sequence.
Remove all parts from the package and make sure you have all
of the items.
1 Lean unit A against the wall as shown.
Spread a large soft cloth, such as a blanket, as shown to
protect the floor and wall surfaces.
Lean unit A against the wall with the key cover closed and
the keyboard side on the bottom.
CAUTION
Be careful not to pinch your fingers.
NOTICE
The top part of the music rest is not fixed. Support the music
rest with your hand so that the music rest will not fall.
Do not place the main unit upside down or with the rear side
facing down.
2 Attach units B and C to unit A.
Align units B and A so that the protrusion fits into the hole.
Fix unit B to the bottom surface of unit A using two long
screws (5 x 30 mm).
Attach the parts, pressing unit B onto unit A so that the two
fit tightly together.
Have a Phillips-head (+) screwdriver of the appropriate size ready.
To prevent the key cover from accidentally opening during assembly,
press down on the key cover, making sure that the sheets (shown) remain
in place.
To prevent damage to the speaker box located at the bottom of unit A,
make sure to place unit A on the styrofoam pads. Also, make sure that the
pads do not touch the speaker box.
Bundled pedal cord
inside. The pedals are
covered with vinyl
covers when shipped
from the factory.
Remove the cover from
the damper pedal for
optimum use of the GP
Responsive Damper
Pedal effect.
4 x 10 mm screws
for the cover (2)
Power cord
5 x 18 mm short screws (10) 4 x 20 mm thin screws (3)
5 x 30 mm long screws (4) Washers (4)
Headphone hanger
4 x 10 mm
thin screws (2)
Protective pads (2)
Large soft cloth
Styrofoam
pads
NOTICE
Do not touch the speaker net.
Doing so may damage the
speaker inside.
Protective pads
Protective pads
CVP-609/605 Owner’s Manual
97
CVP-609 Assembly
Fix unit B to the speaker box of unit A using two short
screws (5 x 18 mm).
If the screw holes do not align, loosen the other screws and
adjust the position of unit B.
Fasten unit C to unit A in the same way.
3 Attach unit E to unit D.
Fix unit E to unit D using two short screws (5 x 18 mm).
4 Attach unit D to unit A.
Fix unit D to the bottom surface of unit A using two short
screws (5 x 18 mm).
Fix unit D to the speaker box of unit A using two short
screws (5 x 18 mm).
If the screw holes do not align, loosen the other screws and
adjust the position of unit D.
5 Raise unit A into the upright position.
CAUTION
Be careful not to pinch your fingers.
When you raise the unit, do not hold the key cover.
6 Install unit F.
Remove the cover from unit D.
Untie and straighten out the bundled cord.
Pass the pedal cord from under unit D to the backside of
the main unit.
Place unit F on the bracket of unit D.
Attach unit F to unit D using three thin screws (4 x 20 mm).
7 Connect the pedal cord.
Washers
Insert the pedal cord plug into the
pedal connector.
Insert the plug into the connector
so that the side with the arrow
mark is facing forward (keyboard
side). If the plug does not fit easily
do not try to force it, but check the
plug for correct orientation, and
then reinsert it into the connector.
Insert the pedal cord securely
until the metal part of the cord
plug disappears from view.
Otherwise, the pedal may not
function properly.
CVP-609/605 Owner’s Manual
98
CVP-609 Assembly
Attach unit G using two screws for the cover (4 x 10 mm).
8 Plug the power cord into the power
connector.
For models that feature a voltage selector:
Set the voltage selector to an appropriate voltage.
9 Rotate the adjuster until it comes in firm
contact with the floor surface.
10Attach the headphone hanger.
Attach the headphone hanger using two thin screws (4 x
10 mm) as shown in the illustration.
Voltage Selector
Before connecting the AC power cord, check the setting of the
voltage selector which is provided in some areas. To set the selector
for 110V, 127V, 220V or 240V main voltages, use a “minus
screwdriver to rotate the selector dial so that the correct voltage for
your region appears next to the pointer on the panel. The voltage
selector is set at 240V when the unit is initially shipped. After the
proper voltage has been selected, connect the AC power cord to the
AC IN jack and an AC wall outlet. A plug adaptor may be also
provided in some areas to match the pin configuration of the AC
wall outlets in your area.
WARNING
An improper voltage setting can cause serious damage to
the instrument or result in improper operation.
Pass the pedal
cord between
units D and E.
Align the pedal cord into the
groove on unit D, then install
the cover onto the groove
correctly.
Correct
Incorrect
After completing the assembly, please check the following.
•Are there any parts left over?
→ Review the assembly procedure and correct any errors.
Is the Clavinova clear of doors and other movable
fixtures?
→ Move the Clavinova to an appropriate location.
Does the Clavinova make a rattling noise when you
shake it?
→ Tighten all screws.
Does the pedal box rattle or give way when you step on
the pedals?
→ Turn the adjuster so that it is set firmly against the floor.
Are the pedal and power cords inserted securely into
the sockets?
CAUTION
When moving the instrument, always hold the bottom of the
main unit. Do not hold the key cover or top portion. Improper
handling can result in damage to the instrument or personal
injury.
Transp orting
If you move to another location, you can transport the instrument
along with other belongings. You can move the unit as it is
(assembled) or you can disassemble the unit down to the condition
it was in when you first took it out of the box. Transport the
keyboard horizontally. Do not lean it up against a wall or stand it up
on its side. Do not subject the instrument to excessive vibration or
shock. When transporting the assembled instrument, make sure all
screws are properly tightened and have not been loosened by
moving the instrument.
CAUTION
If the unit creaks or is otherwise unsteady when you play on
the keyboard, refer to the assembly diagrams and retighten
all screws.
Hold here.
Do not hold here.
CVP-609/605 Owner’s Manual
99
CVP-605 Assembly
CVP-605 Assembly
CAUTION
Assemble the unit on a hard and flat floor with ample space.
Be careful not to confuse or misplace the parts, and be sure to
install all parts in the correct orientation. Please assemble the
unit in accordance with the sequence described here.
Assembly should be carried out by at least two persons.
Be sure to use only the included screws of the specified sizes.
Do not use any other screws. Use of incorrect screws can cause
damage or malfunction of the product.
Be sure to tighten all screws upon completing assembly of each
unit.
To disassemble the unit, reverse the assembly sequence.
Remove all parts from the package and make sure you have all
of the items.
1 Attach units D and E to unit C.
Untie and straighten out the bundled pedal cord.
You will need the vinyl tie later in step 5.
Attach units D and E to unit C by tightening four long
screws (6 x 20 mm).
2 Attach unit B to the above assembly.
Align the screw holes on the upper side of unit B with the
bracket holes on units D and E, then attach the upper
corners of unit B to units D and E by manually tightening
two thin screws (4 x 12 mm).
Secure the bottom end of unit B using four tapping screws
(4 x 20 mm).
Securely tighten the screws on the top of unit B that were
attached in step 2-
.
3 Mount unit A on the above assembly.
Be sure to place your hands at least 15 cm from either end
of the main unit when positioning it.
CAUTION
Be extra careful not to drop the unit or let your fingers be
pinched by the main unit.
Do not hold the main unit in any position other than the position
specified here.
Have a Phillips-head (+) screwdriver of the appropriate size ready.
A
B
C
D
E
To prevent damage to the speaker box located at the bottom of unit A,
make sure to place unit A on the styrofoam pads. Also, make sure that
the pads do not touch the speaker box.
Bundled pedal cord inside here.
6 x 20 mm long screws (4)
6 x 16 mm short screws (6)
4 x 12 mm thin screws (2)
4 x 20 mm tapping screws (4)
Cord holders (2)
Headphone hanger
Power cord
4 x 10 mm
thin screws (2)
D
C
E
B
E
D
A
Align the
screw holes.
15 cm distance or further
CVP-609/605 Owner’s Manual
100
CVP-605 Assembly
4 Secure unit A to the assembly.
Adjust the position of unit A so that the left and right ends
of unit A project beyond units D and E equally (as seen
from the front).
Secure unit A by tightening six short screws (6 x 16 mm)
from the front.
5 Connect the pedal cord and power cord.
Insert the plug of the pedal cord into the pedal connector.
Insert the pedal cord securely
until the metal part of the cord
plug disappears from view.
Otherwise, the pedal may not
function properly.
Attach the cord holders to the rear panel as shown, then clip
the cord into the holders.
Use a vinyl tie to take up any slack in the pedal cord.
Plug the power cord into the power connector.
For models that feature a voltage selector:
Set the voltage selector to an appropriate voltage.
6 Rotate the adjuster until it comes in firm
contact with the floor surface.
7 Attach the headphone hanger.
Attach the headphone hanger using two thin screws (4 x
10 mm) as shown in the illustration.
A
A
Voltage S elector
Before connecting the AC power cord, check the setting of the
voltage selector which is provided in some areas. To set the selector
for 110V, 127V, 220V or 240V main voltages, use a “minus
screwdriver to rotate the selector dial so that the correct voltage for
your region appears next to the pointer on the panel. The voltage
selector is set at 240V when the unit is initially shipped. After the
proper voltage has been selected, connect the AC power cord to the
AC IN jack and an AC wall outlet. A plug adaptor may be also
provided in some areas to match the pin configuration of the AC
wall outlets in your area.
WARNING
An improper voltage setting can cause serious damage to
the instrument or result in improper operation.
After completing the assembly, please check the following.
•Are there any parts left over?
→ Review the assembly procedure and correct any errors.
Is the Clavinova clear of doors and other movable
fixtures?
→ Move the Clavinova to an appropriate location.
Does the Clavinova make a rattling noise when you
shake it?
→ Tighten all screws.
Does the pedal box rattle or give way when you step on
the pedals?
→ Turn the adjuster so that it is set firmly against the floor.
Are the pedal and power cords inserted securely into
the sockets?
CVP-609/605 Owner’s Manual
101
CVP-605 Assembly
CAUTION
When moving the instrument, always hold the bottom of the
main unit. Do not hold the key cover or top portion. Improper
handling can result in damage to the instrument or personal
injury.
Transp orting
If you move to another location, you can transport the instrument
along with other belongings. You can move the unit as it is
(assembled) or you can disassemble the unit down to the condition
it was in when you first took it out of the box. Transport the
keyboard horizontally. Do not lean it up against a wall or stand it up
on its side. Do not subject the instrument to excessive vibration or
shock. When transporting the assembled instrument, make sure all
screws are properly tightened and have not been loosened by
moving the instrument.
CAUTION
If the unit creaks or is otherwise unsteady when you play on
the keyboard, refer to the assembly diagrams and retighten
all screws.
Do not hold here.
Hold here.
CVP-609/605 Owner’s Manual102
Troubleshooting
Troubleshooting
Overall
A click or pop is heard when the power is
turned on or off.
Electrical current is being applied to the instrument. This is normal.
The power is automatically turned off. This is normal and due to the Auto Power Off function. If necessary, set the
parameter of the Auto Power Off function (page 15).
Noise is heard from the instrument’s
speakers.
Noise may be heard if a mobile phone is used near the instrument or if the
phone is ringing. Turn off the mobile phone, or use it further away from the
instrument.
In the LCD, there are some specific points
that are always lit or unlit.
These are the result of defective pixels and occasionally occur in TFT-
LCDs; they do not indicate a problem in operation.
Noise is heard from the instrument’s
speakers or headphones when using the
instrument with the application on iPhone/
iPad.
When you use the instrument along with the application on your iPhone/
iPad, we recommend that you set “Airplane Mode” to “ON” on your
iPhone/iPad in order to avoid noise caused by communication.
Mechanical noise is heard during
performance.
The keyboard mechanism of this instrument simulates the keyboard
mechanism of an actual piano. Mechanical noise is also heard on a piano.
There is a slight difference in sound quality
among different notes played on the
keyboard.
This is normal and is a result of the instrument’s sampling system.
Some Voices have a looping sound.
Some noise or vibrato is noticeable at higher
pitches, depending upon the Voice.
The overall volume is too low or no sound is
heard.
The master volume may be set too low. Set it to an appropriate level with
the [MASTER VOLUME] dial.
All keyboard parts are set to off. On the Home display, touch [Main]/
[Layer]/[Left] to turn on the part (page 42).
The volume of the individual parts may be set too low. Raise the volume in
the Balance display (page 38).
Make sure the desired channel is set to on (page 83).
Headphones are connected, disabling the speaker output. Unplug the
headphones.
Make sure that the “Speaker” is set to “On” from [Menu] [Utility]
[Speaker/Connectivity].
The sound is distorted or noisy. The volume may be turned up too high. Make sure all relevant volume
settings are appropriate.
This may be caused by certain effects or filter resonance settings. Check
the effect or filter settings and change them accordingly in the Mixer
display, referring to the Reference Manual on the website.
Not all simultaneously played notes sound. You are probably exceeding the maximum polyphony (page 106) of the
instrument. When the maximum polyphony is exceeded, the earliest
played notes will stop sounding, letting the latest played notes sound.
The keyboard volume is lower than the Song/
Style playback volume.
The volume of the keyboard parts may be set too low. Raise the keyboard
volume (Main/Layer/Left), or lower the Song/Style volume in the Balance
display (page 38).
Some characters of the file/folder name are
garbled.
The language settings have been changed. Set the appropriate language
for the file/folder name (page 16).
CVP-609/605 Owner’s Manual
103
Troubleshooting
An existing file is not shown on the display. The file extension (.MID, etc.) may have been changed or deleted.
Manually rename the file on a computer, adding the appropriate
extension.
Data files with names of more than 50 characters cannot be handled by
the instrument. Rename the file, reducing the number of characters to 50
or less.
Voice
The Voice selected from the Voice Selection
display does not sound.
Check whether or not the selected part is turned on (page 42).
A strange “flanging” or “doubling” sound
occurs. The sound is slightly different each
time the keys are played.
The Main and Layer parts are set to on, and both parts are set to play the
same Voice. Turn off the Layer part or change the Voice of one of the
parts.
Some Voices will jump an octave in pitch
when played in the upper or lower registers.
This is normal. Some Voices have a pitch limit which, when reached,
causes this type of pitch shift.
Style
The Style does not start even when the
[START/STOP] button is pressed.
The Rhythm channel of the selected Style may not contain any data. Turn
the [ACMP ON/OFF] button on and play in the left-hand section on the
keyboard to sound the accompaniment part of the Style.
Only the rhythm channel plays;
accompaniment sounds are not heard.
Make sure the Auto Accompaniment function is turned on; press the
[ACMP ON/OFF] button.
You may be playing keys in the right hand range of the keyboard. Make
sure to play keys in the chord section of the keyboard.
Styles in a USB flash memory cannot be
selected.
If the size of the Style data is large (about 120 KB or greater), the Style
cannot be selected because the data is too large to be read by the
instrument.
Song
Songs cannot be selected. This may be because the language settings have been changed. Set the
appropriate language for the Song file name (page 16).
If the size of the Song data is large (about 300 KB or greater), the Song
cannot be selected because the data is too large to be read by the
instrument.
Song playback does not start. The Song has been stopped at the end of the Song data. Return to the
beginning of the Song by pressing the SONG CONTROL [STOP] button.
In the case of a Song to which write-protect has been applied, there are
some restrictions and playback may not be possible. For details, refer to
page 33.
(MIDI)
Song playback stops before the Song is
finished.
The Guide function is turned on. (In this case, playback is “waiting” for the
correct key to be played.) Turn off the Guide function (page 63).
(MIDI)
The measure number is different from that of
the score in the Song Position display, shown
by pressing the [REW]/[FF] buttons.
This happens when playing back music data for which a specific, fixed
tempo is set.
(MIDI)
When playing back a Song, some channels
do not play.
Playback of these channels may be set to off. Turn playback on for those
channels that are set to off (page 83).
Overall
CVP-609/605 Owner’s Manual
104
Troubleshooting
(MIDI)
The Guide lamps do not light during Song
playback, even after turning on the Guide
function.
Any notes outside of the 88-key range cannot be indicated by the Guide
lamps.
(MIDI)
The Guide lamps light an octave or two lower/
higher than the actual pitch.
The Guide lamps sometimes light an octave or two lower/higher than the
actual pitch depending on the selected Voice.
(MIDI)
The tempo, beat, measure and music notation
is not displayed correctly.
Some Song data for the instrument has been recorded with special “free
tempo” settings. For such Song data, the tempo, beat, measure and
music notation will not be displayed correctly.
A “USB memory is unavailable” message
appeared, and then the recording was
aborted.
Make sure to use a compatible USB flash memory (page 88).
Make sure that the USB flash memory has enough memory (page 89).
If you are using a USB flash memory to which data has already been
recorded, check first that no important data remains on the device, then
format it (page 89) and try recording again.
The Song playback volume differs depending
on the selected Song.
The volume of MIDI Songs and Audio Songs are set independently. Adjust
the volume in the Balance display (page 38) after selecting a Voice.
Microphone
The microphone input signal cannot be
recorded.
The microphone input signal cannot be recorded by MIDI recording.
Record by Audio recording (page 66).
Harmony can be heard in addition to the
microphone sound.
Vocal Harmony is set to “On.” Turn Vocal Harmony off (page 72).
The Vocal Harmony effect sounds distorted or
out-of-tune.
Your vocal microphone may be picking up extraneous sounds, such as
the Style sound from the instrument. In particular, bass sounds can cause
mistracking of Vocal Harmony. To remedy this:
Sing as closely to the microphone as possible.
Use a unidirectional microphone.
Turn down the Master volume, or adjust the volume balance on the
Balance display (page 38).
The Vocal Harmony effect is not applied even
when it is turned on.
In the Chordal mode, Vocal Harmony is added only when chords are
detected. Try one of the following:
Turn on the [ACMP ON/OFF] button and play chords in the chord
section during Style playback.
Turn on the Left part and play chords in the left hand section.
Play back a Song which contains chords.
Set the “Stop ACMP” parameter to something other than “Disabled” via
[Menu] [StyleSetting] [Setting]. For details, refer to the Reference
Manual on the website.
Mixer
The sound seems strange or different than
expected when changing a rhythm Voice
(drum kit, etc.) of the Style or Song from the
Mixer.
When changing the rhythm/percussion Voices (drum kits, etc.) of the Style
and Song from the VOICE parameter, the detailed settings related to the
drum voice are reset, and in some cases you may be unable to restore the
original sound. In the case of Song playback, you can restore the original
sound by returning to the beginning of the Song and playing back from
that point. In the case of Style play, you can restore the original sound by
selecting the same Style again.
Song
CVP-609/605 Owner’s Manual
105
Troubleshooting
Pedal/AUX Pedal
The damper, sostenuto and soft functions do
not work for the relevant pedals.
The pedal cord plug is not connected. Securely insert the pedal cord plug
into the proper jack (pages 94, 97, 100).
Make sure that each pedal is properly assigned to “Sustain,” “Sostenuto
and “Soft” (page 35).
The on/off setting of the footswitch
connected to the [AUX PEDAL] jack is
reversed.
Turn the instrument’s power off, then turn it on again without pressing the
footswitch, or change the Polarity parameter from [Menu] [Assignable]
[Pedal].
AUX IN jack
Sound input to the [AUX IN] jack is
interrupted.
The output volume of the external device connected to this instrument is
too low. Increase the output volume of the external device. The volume
level reproduced via this instrument’s speakers can be adjusted by using
the [MASTER VOLUME] control.
The Noise Gate function may be cutting the soft sounds. If this happens,
turn off the “AUX In Noise Gate” parameter (page 85).
CVP-609/605 Owner’s Manual106
Specifications
Specifications
CVP-609GP
(Grand Piano type)
CVP-609 CVP-605
Size/Weight Width
[For models with polished finish]
[1,435 mm (56-1/2")] 1,426 mm (56-1/8")
[1,429 mm (56-1/4")]
1,420 mm (55-15/16")
[1,422 mm (56")]
Height
[For models with
polished finish]
Without Music Rest [913 mm (35-15/16")] 868 mm (34-3/16")
[872 mm (34-5/16")]
868 mm (34-3/16")
[872 mm (34-5/16")]
With Music Rest [1,077 mm (42-3/8")] 1,025 mm (40-3/8")
[1,027 mm (40-7/16")]
1,025 mm (40-3/8")
[1,027 mm (40-7/16")]
With Lid Up [1,556 mm (61-1/4")] -
Depth
[For models with
polished finish]
Without Music Rest [1,150 mm (45-1/4")] 612 mm (24-1/8")
[612 mm (24-1/8")]
606 mm (23-7/8")
[607 mm] (23-7/8")
With Music Rest 611 mm (24-1/16")
[611 mm (24-1/16")]
581 mm (22-7/8")
[581 mm (22-7/8")]
Weight
[For models with polished finish]
[109 kg (240 lbs., 5 oz.)] 81 kg (178 lbs., 9 oz.)
[84 kg (185 lbs., 3 oz)]
79 kg (174 lbs., 3 oz.)
[81 kg (178 lbs., 9 oz.)]
Control
Interface
Keyboard Number of Keys 88
Type Natural Wood (NW) Keyboard
with Synthetic Ivory Keytops
(with real-wood white keys)
Graded Hammer 3 (GH3)
Keyboard with Synthetic
Ivory Keytops
88-key Linear
Graded Hammers
Yes
Touch Sensitivity Hard2/Hard1/Medium/Soft1/Soft2
Pedal Number of Pedals 3
Half Pedal Yes
GP Response
Damper Pedal
Yes
Functions Sustain, Sostenuto, Soft, Glide, Song Play/Pause, Style Start/Stop, Volume, etc.
Display Type TFT Color Wide VGA LCD
Size 800 x 480 dots
8.5 inch
800 x 480 dots
7 inch
Touch Screen Yes
Score Display
Function
Yes
Lyrics Display
Function
Yes
Text Viewer
Function
Yes
Language English, Japanese, German, French, Spanish, Italian
Panel Language English
Cabinet Key Cover Style Folding
Music Rest Yes
Music Clips Yes
Voices Tone Generation Tone Generating
Technology
RGE (Real Grand Expression)
Stereo Sustain
Samples
Yes
Key-off Samples Yes
String Resonance Yes
Smooth Release Yes
Damper Resonance Yes
Polyphony Number of
Polyphony (Max.)
128 + 128 256
CVP-609/605 Owner’s Manual
107
Specifications
Voices Preset Number of Voices 1,140 Voices + 35 Drum/SFX Kits + 480 XG Voices +
GM2 + GS (for GS Song Playback)
847 Voices + 28 Drum/SFX
Kits + 480 XG Voices +
GM2 + GS (for GS Song
Playback)
Featured Voices 96 Natural Voices, 164 Super Articulation Voices,
30 Super Articulation 2 Voices, 43 MegaVoices,
31 Sweet! Voices, 80 Cool! Voices, 102 Live! Voices,
30 Organ Flutes! Voices
57 Natural Voices,
62 Super Articulation
Voices, 23 MegaVoices,
27 Sweet! Voices, 67 Cool!
Voices, 76 Live! Voices,
20 Organ Flutes! Voices
Custom Voice Edit Yes
Compatibility XG, GS (for Song playback), GM, GM2, XF
Effects Types Reverb 44 Preset + 3 User
Chorus 106 Preset + 3 User
Insertion Effect 310 Preset + 10 User 297 Preset + 10 User
Variation Effect 308 Preset + 3 User 295 Preset + 3 User
Master Compressor 5 Preset + 5 User
Master EQ 5 Preset + 2 User
Part EQ 27 Parts
Vocal Harmony VH2: 44 Preset + 60 User VH1: 60 Preset + 60 User
Intelligent Acoustic
Control (IAC)
Yes
Functions Dual (Layer) Yes
Split Yes
Styles Preset Number of Preset
Styles
566 420
Featured Styles 468 Pro Styles, 55 Session Styles, 7 Free Play Styles,
36 Pianist Styles
349 Pro Styles, 33 Session
Styles, 2 Free Play Styles,
36 Pianist Styles
File Format Style File Format GE (Guitar Edition)
Fingering Single Finger, Fingered, Fingered On Bass, Multi Finger, AI Fingered, Full Keyboard,
AI Full Keyboard
Style Control INTRO x 3, MAIN VARIATION x 4, FILL x 4, BREAK, ENDING x 3
Custom Style Creator Yes
Other Features Music Finder (max.) 2,500 Records
One Touch Setting
(OTS)
4 for each Style
Style
Recommender
Yes
Songs (MIDI) Preset Number of Preset
Songs
124
Recording Number of Tracks 16
Data Capacity approx. 300KB/Song
Compatible Data
Format
Recording SMF (Format 0)
Playback SMF (Format 0 & 1), ESEQ, XF
Songs (Audio) Recording Time (max.) 80 minutes/Song
Compatible Data
Format
Recording .wav, .mp3 (MPEG-1 Audio Layer-3)
Playback .wav, .mp3 (MPEG-1 Audio Layer-3)
Time Stretch Yes
Pitch Shift Yes
Vocal Cancel Yes
CVP-609GP
(Grand Piano type)
CVP-609 CVP-605
CVP-609/605 Owner’s Manual
108
Specifications
* Specifications and descriptions in this Owner's Manual are for information purposes only. Yamaha Corp. reserves the right to change or modify
products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please
check with your Yamaha dealer.
Functions Registration
Memory
Number of Buttons 8
Control Registration Sequence, Freeze
Lesson/Guide Follow Lights, Any Key, Karao-Key, Your Tempo
Guide Lamp Yes
Performance
Assistant
Technology (PAT)
Yes
Demo Yes
Overall Controls Metronome Yes
Tempo Range 5 – 500, Tap Tempo
Transpose -12 – 0 – +12
Tuning 414.8 – 440 – 466.8 Hz
Scale Type 9 Types
Miscellaneous Piano Room Yes
Storage and
Connectivity
Storage Internal Memory approx. 6.7 MB approx. 2.5 MB
External Memory Optional USB Flash Memory (via USB TO DEVICE)
Connectivity Headphones x 2
Microphone Input Volume, Mic./Line In
MIDI IN/OUT/THRU
AUX IN Stereo Mini
AUX OUT L/L+R, R
AUX PEDAL Yes
VIDEO OUT Yes
RGB OUT Yes
USB TO DEVICE Yes (x 2)
USB TO HOST Yes
Sound system Amplifiers (40W + 30W + 15W) x 2 (30W + 30W) x2 + 80W 45W x 2
Speakers 16cm x 2 + 5cm x 2 + 3cm
(dome) x 2
20cm x 1 + 16cm x 2 + 5cm
x 2 + 3cm (dome) x 2
16cm x 2 + 5cm x 2
Acoustic Optimizer Yes
Accessories Owner's Manual, Data List, “50 Greats for the Piano” Music Book, Online Member
Product Registration, AC Power Cord, Bench (included or optional), USB Wireless LAN
Adapter (may be included depending on your locale.)
Optional
Accessories
Headphones HPE-160
Footswitches FC4, FC5
Foot controller FC7
MIDI Interface i-MX1
USB MIDI Interface i-UX1
CVP-609GP
(Grand Piano type)
CVP-609 CVP-605
CVP-609/605 Owner’s Manual 109
Index
Index
A
A-B Repeat ........................................................................64
AI Fingered .......................................................................56
AI Full Keyboard ..............................................................56
Assembly .............................................................. 93, 96, 99
ASSIGNABLE buttons ....................................................28
Attack .................................................................................47
Audio connection .............................................................85
Audio conversion .............................................................70
Audio recording ...............................................................66
Audio Song ........................................................................57
Auto Fill .............................................................................51
Auto Power Off ................................................................16
B
Backup ...............................................................................39
Balance ...............................................................................38
Bank ...................................................................................79
Break ..................................................................................51
C
Channel ...................................................................... 68, 83
Character entry .................................................................33
Chordal ..............................................................................72
Chorus ...............................................................................82
Compressor .......................................................................82
Computer ..........................................................................90
Connection ........................................................................84
Copyright ..........................................................................16
D
Damper pedal ...................................................................35
Data dial ............................................................................26
Delete .................................................................................31
Demo .................................................................................11
Display ...............................................................................22
E
Effect ..................................................................................82
Ending section ..................................................................51
EQ .......................................................................................82
F
Factory Reset .....................................................................39
Fast Forward .....................................................................59
Favorite ..............................................................................32
File Selection display ........................................................23
Filter ...................................................................................82
Fingered ............................................................................56
Fingered On Bass .............................................................56
Fingering type ...................................................................55
Fixed Velocity ...................................................................37
Folder .................................................................................30
Foot Controller ................................................................87
Footswitch .........................................................................87
Force-quit ..........................................................................15
Format ...........................................................................9, 89
Full Keyboard ...................................................................56
G
GP Responsive Damper Pedal .......................................35
Guide .................................................................................63
H
Half-pedal .........................................................................35
Headphones ......................................................................19
Home display ....................................................................22
I
Initialize (Factory Reset) .................................................39
Intro section ......................................................................51
iPad ....................................................................................89
iPhone ................................................................................89
L
Language ...........................................................................16
Layer part ..........................................................................42
Left Hold ...........................................................................37
Left part .............................................................................42
Left Split Point ..................................................................45
Lid ......................................................................................18
Lyrics .................................................................................61
M
Main part ..........................................................................42
Main section .....................................................................51
Master Compressor .........................................................82
Menu area .........................................................................22
Menu display ..............................................................24, 91
Metronome .......................................................................36
Microphone ......................................................................71
MIDI connection .............................................................90
MIDI recording ................................................................66
MIDI Song ........................................................................57
Mixer .................................................................................81
Monitor .............................................................................86
Move ..................................................................................31
CVP-609/605 Owner’s Manual
110
Index
Multi Finger ......................................................................55
Music Finder .....................................................................74
Music notation .................................................................60
Music rest ..........................................................................17
N
Noise Gate .........................................................................85
O
One Touch Setting ...........................................................52
Organ Flutes Voice ..........................................................47
OTS ....................................................................................52
OTS Link ...........................................................................52
Owner Name .....................................................................16
P
Pan ......................................................................................82
Pause ..................................................................................59
Pedal ............................................................................ 35, 87
Piano Lock .........................................................................41
Piano Reset ........................................................................44
Piano Room ......................................................................40
Pitch ............................................................................ 38, 65
Pitch Shift ..........................................................................65
Playback (Song) ................................................................57
Playback (Style) ................................................................50
Power .................................................................................14
Power indicator ................................................................14
R
Record ......................................................................... 74, 75
Recording ..........................................................................66
Registration area ...............................................................22
Registration Memory .......................................................78
Rename ..............................................................................30
Repeat ................................................................................64
Response ............................................................................47
Restore ...............................................................................39
Reverb ................................................................................82
Rewind ...............................................................................59
Rotary Speaker ..................................................................47
S
SA Voice ............................................................................46
SA2 Voice ..........................................................................46
Save ....................................................................................29
Score ...................................................................................60
Screen Out .........................................................................86
Shortcut .............................................................................27
Single Finger .....................................................................55
Smart device ......................................................................89
Soft pedal ...........................................................................35
Song ................................................................................... 57
Song area ...........................................................................22
Sostenuto pedal ................................................................35
Speed (tempo) ............................................................36, 65
Split Point .........................................................................45
Style ....................................................................................48
Style area ...........................................................................22
Style Recommender .........................................................54
Style Split Point ................................................................45
Super Articulation Voice ................................................46
Synchro Start (MIDI Song) ............................................60
Synchro Start (Style) ........................................................50
Synchro Stop .....................................................................50
T
Talk ....................................................................................73
Tempo .........................................................................36, 65
Text ....................................................................................62
Time Stretch .....................................................................65
Touch Curve .....................................................................37
Touch Response ...............................................................37
Touch screen ....................................................................25
Touch Sensitivity .............................................................37
Transpose ..........................................................................38
Tuning ...............................................................................38
U
USB flash memory ...........................................................88
User memory ....................................................................23
User tab .............................................................................23
V
Version ..............................................................................16
Vibrato ..............................................................................47
Vocal Cancel .....................................................................65
Vocal Harmony ................................................................72
Vocoder .............................................................................72
Vocoder-Mono .................................................................72
Voice ..................................................................................42
Voice area ..........................................................................22
Volume ..............................................................................14
Volume Balance ...............................................................38
W
Wireless LAN ...................................................................89
CVP-609/605 Owner’s Manual
111
OBSERVERA!
Apparaten kopplas inte ur växelströmskällan (nätet)
så länge som den ar ansluten till vägguttaget, även
om själva apparaten har stängts av.
ADVARSEL: Netspændingen til dette apparat er
IKKE afbrudt, sålænge netledningen sidder i en stik-
kontakt, som er tændt — også selvom der er slukket
på apparatets afbryder.
VAROITUS: Laitteen toisiopiiriin kytketty käyttökyt-
kin ei irroita koko laitetta verkosta.
(standby)
T
he model number, serial number, power requirements
,
etc., may be found on or near the name plate, which is
at the bottom of the unit. You should note this serial
number in the space provided below and retain this
manual as a permanent record of your purchase to aid
identification in the event of theft.
Model No.
Serial No.
(bottom_en_01)
Information for Users on Collection and Disposal of Old Equipment
This symbol on the products, packaging, and/or accompanying documents means that used electrical and
electronic products should not be mixed with general household waste.
For proper treatment, recovery and recycling of old products, please take them to applicable collection
points, in accordance with your national legislation and the Directives 2002/96/EC.
By disposing of these products correctly, you will help to save valuable resources and prevent any potential
negative effects on human health and the environment which could otherwise arise from inappropriate
waste handling.
For more information about collection and recycling of old products, please contact your local municipality, your waste
disposal service or the point of sale where you purchased the items.
[For business users in the European Union]
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.
[Information on Disposal in other Countries outside the European Union]
This symbol is only valid in the European Union. If you wish to discard these items, please contact your local
authorities or dealer and ask for the correct method of disposal.
(weee_eu)
CVP-609/605 Owner’s Manual
112
The followings are the titles, credits and copyright notices for fifty seven
(57) of the songs pre-installed in this instrument (CVP-609/605):
Alfie
Theme from the Paramount Picture ALFIE
Words by Hal David
Music by Burt Bacharach
Copyright © 1966 (Renewed 1994) by Famous Music Corporation
International Copyright Secured All Rights Reserved
All Shook Up
Words and Music by Otis Blackwell and Elvis Presley
Copyright © 1957 by Shalimar Music Corporation
Copyright Renewed and Assigned to Elvis Presley Music
All Rights Administered by Cherry River Music Co. and Chrysalis Songs
International Copyright Secured All Rights Reserved
Beauty And The Beast
from Walt Disney’s BEAUTY AND THE BEAST
Lyrics by Howard Ashman
Music by Alan Menken
© 1991 Walt Disney Music Company and Wonderland Music Company,
Inc.
All Rights Reserved Used by Permission
same Mucho (Kiss Me Much)
Music and Spanish Words by Consuelo Velazquez
English Words by Sunny Skylar
Copyright © 1941, 1943 by Promotora Hispano Americana de Musica,
S.A.
Copyrights Renewed
All Rights Administered by Peer International Corporation
International Copyright Secured All Rights Reserved
Blue Hawaii
from the Paramount Picture WAIKIKI WEDDING
Words and Music by Leo Robin and Ralph Rainger
Copyright © 1936, 1937 (Renewed 1963, 1964) by Famous Music
Corporation
International Copyright Secured All Rights Reserved
Blue Moon
Words by Lorenz Hart
Music by Richard Rodgers
© 1934 (Renewed 1962) METRO-GOLDWYN-MAYER INC.
All Rights Controlled by EMI ROBBINS CATALOG INC. (Publishing)
and WARNER BROS. PUBLICATIONS U.S. INC. (Print)
All Rights Reserved Used by Permission
Brazil
Words and Music by Ray Barroso
English lyrics by S. K. Russell
Copyright © 1941 by Peer International Corporation
Copyright Renewed
International Copyright Secured All Rights Reserved
California Girls
Words and Music by Brian Wilson and Mike Love
Copyright © 1965 IRVING MUSIC, INC.
Copyright Renewed
All Rights Reserved Used by Permission
Can You Feel The Love Tonight
from Walt Disney Pictures’ THE LION KING
Music by Elton John
Lyrics by Tim Rice
© 1994 Wonderland Music Company, Inc.
All Rights Reserved Used by Permission
Cant Help Falling In Love
from the Paramount Picture BLUE HAWAII
Words and Music by George David Weiss, Hugo Peretti and Luigi
Creatore
Copyright © 1961 by Gladys Music, Inc.
Copyright Renewed and Assigned to Gladys Music
All Rights Administered by Cherry Lane Music Publishing Company, Inc.
and Chrysalis Music
International Copyright Secured All Rights Reserved
Chim Chim Cher-ee
from Walt Disney’s MARY POPPINS
Words and Music by Richard M. Sherman and Robert B. Sherman
© 1963 Wonderland Music Company, Inc.
Copyright Renewed
All Rights Reserved Used by Permission
Do-Re-Mi
from THE SOUND OF MUSIC
Lyrics by Oscar Hammerstein II
Music by Richard Rodgers
Copyright © 1959 by Richard Rodgers and Oscar Hammerstein II
Copyright Renewed
WILLIAMSON MUSIC owner of publication and allied rights throughout
the world
International Copyright Secured All Rights Reserved
Don’t Be Cruel (To A Heart That’s True)
Words and Music by Otis Blackwell and Elvis Presley
Copyright © 1956 by Unart Music Corporation and Elvis Presley Music,
Inc.
Copyright Renewed and Assigned to Elvis Presley Music
All Rights Administered by Cherry River Music Co. and Chrysalis Songs
International Copyright Secured All Rights Reserved
Edelweiss
from THE SOUND OF MUSIC
Lyrics by Oscar Hammerstein II
Music by Richard Rodgers
Copyright © 1959 by Richard Rodgers and Oscar Hammerstein II
Copyright Renewed
WILLIAMSON MUSIC owner of publication and allied rights throughout
the world
International Copyright Secured All Rights Reserved
Fly Me To The Moon (In Other Words)
featured in the Motion Picture ONCE AROUND
Words and Music by Bart Howard
TRO - © Copyright 1954 (Renewed) Hampshire House Publishing Corp.,
New York, NY
International Copyright Secured
All Rights Reserved Including Public Performance For Profit
Used by Permission
Hey Jude
Words and Music by John Lennon and Paul McCartney
Copyright © 1968 Sony/ATV Songs LLC
Copyright Renewed
All Rights Administered by Sony/ATV Music Publishing, 8 Music Square
West, Nashville, TN 37203
International Copyright Secured All Rights Reserved
Hound Dog
Words and Music by Jerry Leiber and Mike Stoller
Copyright © 1956 by Elvis Presley Music, Inc. and Lion Publishing Co.,
Inc.
Copyright Renewed, Assigned to Gladys Music and Universal - MCA
Music Publishing, A Division of Universal Studios, Inc.
All Rights Administered by Cherry Lane Music Publishing Company, Inc.
and Chrysalis Music
International Copyright Secured All Rights Reserved
I Just Called To Say I Love You
Words and Music by Stevie Wonder
© 1984 JOBETE MUSIC CO., INC. and BLACK BULL MUSIC
c/o EMI APRIL MUSIC INC.
All Rights Reserved International Copyright Secured Used by
Permission
I Left My Heart In San Francisco
Words by Douglass Cross
Music by George Cory
© 1954 (Renewed 1982) COLGEMS-EMI MUSIC INC.
All Rights Reserved International Copyright Secured Used by
Permission
CVP-609/605 Owner’s Manual
113
In The Mood
By Joe Garland
Copyright © 1939, 1960 Shapiro, Bernstein & Co., Inc., New York
Copyright Renewed
International Copyright Secured All Rights Reserved
Used by Permission
Isn’t She Lovely
Words and Music by Stevie Wonder
© 1976 JOBETE MUSIC CO., INC. and BLACK BULL MUSIC
c/o EMI APRIL MUSIC INC.
All Rights Reserved International Copyright Secured Used by
Permission
Let It Be
Words and Music by John Lennon and Paul McCartney
Copyright © 1970 Sony/ATV Songs LLC
Copyright Renewed
All Rights Administered by Sony/ATV Music Publishing, 8 Music Square
West, Nashville, TN 37203
International Copyright Secured All Rights Reserved
Let’s Twist Again
Words by Kal Mann
Music by Dave Appell and Kal Mann
Copyright © 1961 Kalmann Music, Inc.
Copyright Renewed
All Rights Controlled and Administered by Spirit Two Music, Inc.
(ASCAP)
International Copyright Secured All Rights Reserved
Linus And Lucy
By Vince Guaraldi
Copyright © 1965 LEE MENDELSON FILM PRODUCTIONS, INC.
Copyright Renewed
International Copyright Secured All Rights Reserved
Love Story
Theme from the Paramount Picture LOVE STORY
Music by Francis Lai
Copyright © 1970, 1971 (Renewed 1998, 1999) by Famous Music
Corporation
International Copyright Secured All Rights Reserved
Lullaby Of Birdland
Words by Ge orge David Weiss
Music by George Shearing
© 1952, 1954 (Renewed 1980, 1982) EMI LONGITUDE MUSIC
All Rights Reserved International Copyright Secured Used by
Permission
Michelle
Words and Music by John Lennon and Paul McCartney
Copyright © 1965 Sony/ATV Songs LLC
Copyright Renewed
All Rights Administered by Sony/ATV Music Publishing, 8 Music Square
West, Nashville, TN 37203
International Copyright Secured All Rights Reserved
Mickey Mouse March
from Walt Disney’s THE MICKEY MOUSE CLUB
Words and Music by Jimmie Dodd
© 1955 Walt Disney Music Company
Copyright Renewed
All Rights Reserved Used by Permission
Mission: Impossible Theme
from the Paramount Television Series MISSION: IMPOSSIBLE
By Lalo Schifrin
Copyright © 1966, 1967 (Renewed 1994, 1995) by Bruin Music Company
International Copyright Secured All Rights Reserved
Mona Lisa
from the Paramount Picture CAPTAIN CAREY, U.S.A.
Words and Music by Jay Livingston and Ray Evans
Copyright © 1949 (Renewed 1976) by Famous Music Corporation
International Copyright Secured All Rights Reserved
Moon River
from the Paramount Picture BREAKFAST AT TIFFANY’S
Words by Johnny Mercer
Music by Henry Mancini
Copyright © 1961 (Renewed 1989) by Famous Music Corporation
International Copyright Secured All Rights Reserved
Moonlight Serenade
Words by Mitchell Parish
Music by Glen Miller
Copyright © 1939 (Renewed 1967) by ROBBINS MUSIC
CORPORATION
All Rights Controlled and Administered by EMI ROBBINS CATALOG
INC.
International Copyright Secured All Rights Reserved
My Favorite Things
from THE SOUND OF MUSIC
Lyrics by Oscar Hammerstein II
Music by Richard Rodgers
Copyright © 1959 by Richard Rodgers and Oscar Hammerstein II
Copyright Renewed
WILLIAMSON MUSIC owner of publication and allied rights throughout
the world
International Copyright Secured All Rights Reserved
My Way
By Paul Anka, Jacques Revaux, Claude Francois and Giles Thibault
© 1997 by Chrysalis Standards, Inc.
Used by Permission. All Rights Reserved.
The Nearness Of You
from the Paramount Picture ROMANCE IN THE DARK
Words by Ned Washington
Music by Hoagy Carmichael
Copyright © 1937, 1940 (Renewed 1964, 1967) by Famous Music
Corporation
International Copyright Secured All Rights Reserved
Them e Fro mNe w York , New Yor k
Music by John Kander
Words by Fred Ebb
© 1977 UNITED ARTISTS CORPORATION
All Rights Controlled by EMI UNART CATALOG INC. (Publishing) and
WARNER BROS. PUBLICATIONS U.S. INC. (Print)
All Rights Reserved Used by Permission
Ob-La-Di, Ob-La-Da
Words and Music by John Lennon and Paul McCartney
Copyright © 1968 Sony/ATV Songs LLC
Copyright Renewed
All Rights Administered by Sony/ATV Music Publishing, 8 Music Square
West, Nashville, TN 37203
International Copyright Secured All Rights Reserved
Proud Mary
Words and Music by J.C. Fogerty
© 1968 (Renewed) JONDORA MUSIC
All Rights Reserved Used by Permission
Return To Sender
Words and Music by Otis Blackwell and Winfield Scott
Copyright © 1962 by Elvis Presley Music, Inc.
Copyright Renewed and Assigned to Elvis Presley Music
All Rights Administered by Cherry River Music Co. and Chrysalis Songs
International Copyright Secured All Rights Reserved
The Shoop Shoop Song (It’s In His Kiss)
Words and Music by Rudy Clark
Copyright © 1963, 1964 by Trio Music Company, Inc. and Top Of The
Charts
Copyright Renewed
All Rights for the United States Controlled and Administered by Trio
Music Company, Inc.
All Rights for the World excluding the United States Controlled and
Administered by Trio Music Company, Inc. and Alley Music Corp.
International Copyright Secured All Rights Reserved
Used by Permission
CVP-609/605 Owner’s Manual
114
(Sittin’ On) The Dock Of The Bay
Words and Music by Steve Cropper and Otis Redding
Copyright © 1968, 1975 IRVING MUSIC, INC.
Copyright Renewed
All Rights Reserved Used by Permission
Smoke Gets In Your Eyes
from ROBERTA
Words by Otto Harbach
Music by Jerome Kern
© 1933 UNIVERSAL - POLYGRAM INTERNATIONAL PUBLISHING,
INC.
Copyright Renewed
All Rights Reserved
International Rights Secured. Not for broadcast transmission.
DO NOT DUPLICATE. NOT FOR RENTAL.
WARNING: It is a violation of Federal Copyright Law to synchronize this
Multimedia Disc with video tape or film, or to print the Composition(s)
embodied on this Multimedia Disc in the form of standard music
notation, without the express written permission of the copyright owner.
Somewhere, My Love
Laras Theme from DOCTOR ZHIVAGO
Lyric by Paul Francis Webster
Music by Maurice Jarre
Copyright © 1965, 1966 (Renewed 1993, 1994) Webster Music Co. and
EMI Robbins Catalog Inc.
International Copyright Secured All Rights Reserved
Spanish Eyes
Words by Charles Singleton and Eddie Snyder
Music by Bert Kaempfert
© 1965, 1966 (Renewed 1993, 1994) EDITION DOMA BERT
KAEMPFERT
All Rights for the world, excluding Germany, Austria and Switzerland,
Controlled and Administered by SCREEN GEMS-EMI MUSIC INC.
All Rights Reserved International Copyright Secured Used by
Permission
Speak Softly, Love (Love Theme)
from the Paramount Picture THE GODFATHER
Words by Larry Kusik
Music by Nino Rota
Copyright © 1972 (Renewed 2000) by Famous Music Corporation
International Copyright Secured All Rights Reserved
Stella By Starlight
from the Paramount Picture THE UNINVITED
Words by Ned Washington
Music by Victor Young
Copyright © 1946 (Renewed 1973, 1974) by Famous Music Corporation
International Copyright Secured All Rights Reserved
Take The “A Train
Words and Music by Billy Strayhorn
Copyright © 1941; Renewed 1969 DreamWorks Songs (ASCAP) and Billy
Strayhorn Songs, Inc. (ASCAP) for the U.S.A.
Rights for DreamWorks Songs and Billy Strayhorn Songs, Inc.
Administered by Cherry Lane Music Publishing Company, Inc.
International Copyright Secured All Rights Reserved
Tear s In Hea ven
Words and Music by Eric Clapton and Will Jennings
Copyright © 1992 by E.C. Music Ltd. and Blue Sky Rider Songs
All Rights for E.C. Music Ltd. Administered by Unichappell Music Inc.
All Rights for Blue Sky Rider Songs Administered by Irving Music, Inc.
International Copyright Secured All Rights Reserved
That Old Black Magic
from the Paramount Picture STAR SPANGLED RHYTHM
Words by Johnny Mercer
Music by Harold Arlen
Copyright © 1942 (Renewed 1969) by Famous Music Corporation
International Copyright Secured All Rights Reserved
That’s Amore (That’s Love)
from the Paramount Picture THE CADDY
Words by Jack Brooks
Music by Harry Warren
Copyright © 1953 (Renewed 1981) by Paramount Music Corporation and
Four Jays Music
International Copyright Secured All Rights Reserved
Up Where We Belong
from the Paramount Picture AN OFFICER AND A GENTLEMAN
Words by Will Jennings
Music by Buffy Sainte-Marie and Jack Nitzsche
Copyright © 1982 by Famous Music Corporation and Ensign Music
Corporation
International Copyright Secured All Rights Reserved
Waltz For Debby
Lyric by Gene Lees
Music by Bill Evans
TRO - © Copyright 1964 (Renewed), 1965 (Renewed), 1966 (Renewed)
Folkways Music Publishers, Inc., New York, NY
International Copyright Secured
All Rights Reserved Including Public Performance For Profit
Used by Permission
White Christmas
from the Motion Picture Irving Berlins HOLIDAY INN
Words and Music by Irving Berlin
© Copyright 1940, 1942 by Irving Berlin
Copyright Renewed
International Copyright Secured All Rights Reserved
A Whole New World
from Walt Disney’s ALADDIN
Music by Alan Menken
Lyrics by Tim Rice
© 1992 Wonderland Music Company, Inc. and Walt Disney Music
Company
All Rights Reserved Used by Permission
Ye s te r da y
Words and Music by John Lennon and Paul McCartney
Copyright © 1965 Sony/ATV Songs LLC
Copyright Renewed
All Rights Administered by Sony/ATV Music Publishing, 8 Music Square
West, Nashville, TN 37203
International Copyright Secured All Rights Reserved
You Are The Sunshine Of My Life
Words and Music by Stevie Wonder
© 1972 (Renewed 2000) JOBETE MUSIC CO., INC. and BLACK BULL
MUSIC
c/o EMI APRIL MUSIC INC.
All Rights Reserved International Copyright Secured Used by
Permission
You S exy Thi ng
Words and Music by E. Brown
Copyright © 1975 by Finchley Music Corp.
Administered in the USA and Canada by Music & Media International,
Inc.
Administered for the World excluding the USA and Canada by RAK
Music Publishing Ltd.
International Copyright Secured All Rights Reserved
CVP-609/605 Owner’s Manual
115
For details of products, please contact your nearest Yamaha
representative or the authorized distributor listed below.
Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha
ou au distributeur le plus proche de vous figurant dans la liste suivante.
Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten
Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen
Bestimmungsländern erhältlich.
Para detalles sobre productos, contacte su tienda Yamaha más
cercana o el distribuidor autorizado que se lista debajo.
CANADA
Yamaha Canada Music Ltd.
135 Milner Avenue, Toronto, Ontario,
M1S 3R1, Canada
Tel: 416-298-1311
U.S.A.
Yamaha Corporation of America
6600 Orangethorpe Avenue, Buena Park, CA 90620,
U.S.A.
Tel: 714-522-9011
MEXICO
Yamaha de México, S.A. de C.V.
Av. Insurgentes Sur 1647 “Prisma Insurgentes”,
Col. San Jose Insurgentes, Del. Benito Juarez,
03900, Mexico, D.F.
Tel: 55-5804-0600
BRAZIL
Yamaha Musical do Brasil Ltda.
Rua Joaquim Floriano, 913 - 4º andar, Itaim Bibi,
CEP 04534-013 São Paulo, SP. BRAZIL
Tel: 011-3704-1377
ARGENTINA
Yamaha Music Latin America, S.A.,
Sucursal Argentina
Olga Cossettini 1553, Piso 4 Norte,
Madero Este-C1107CEK
Buenos Aires, Argentina
Tel: 54-11-4119-7000
VENEZUELA
Yamaha Music Latin America, S.A.,
Sucursal Venezuela
C.C. Manzanares Plaza P4
Ofic. 0401- Manzanares-Baruta
Caracas Venezuela
Tel: 58-212-943-1877
PANAMA AND OTHER LATIN
AMERICAN COUNTRIES/
CARIBBEAN COUNTRIES
Yamaha Music Latin America, S.A.
Torre Banco General, Piso No.7, Marbella,
Calle 47 y Aquilino de la Guardia,
Ciudad de Panamá, República de Panamá
Tel: +507-269-5311
THE UNITED KINGDOM/IRELAND
Yamaha Music Europe GmbH (UK)
Sherbourne Drive, Tilbrook, Milton Keynes,
MK7 8BL, U.K.
Tel: 01908-366700
GERMANY
Yamaha Music Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: 04101-3030
SWITZERLAND/LIECHTENSTEIN
Yamaha Music Europe GmbH
Branch Switzerland in Zürich
Seefeldstrasse 94, 8008 Zürich, Switzerland
Tel: 044-387-8080
AUSTRIA
Yamaha Music Europe GmbH Branch Austria
Schleiergasse 20, A-1100 Wien, Austria
Tel: 01-60203900
CZECH REPUBLIC/HUNGARY/
ROMANIA/SLOVAKIA/SLOVENIA
Yamaha Music Europe GmbH
Branch Austria (Central Eastern Europe Office)
Schleiergasse 20, A-1100 Wien, Austria
Tel: 01-60203900
POLAND/LITHUANIA/LATVIA/
ESTONIA
Yamaha Music Europe GmbH
Branch Poland Office
ul. Wrotkowa 14 02-553 Warsaw, Poland
Tel: 022-500-2925
BULGARIA
Dinacord Bulgaria LTD.
Bul.Iskarsko Schose 7 Targowski Zentar Ewropa
1528 Sofia, Bulgaria
Tel: 02-978-20-25
MALTA
Olimpus Music Ltd.
The Emporium, Level 3, St. Louis Street Msida
MSD06
Tel: 02133-2144
NETHERLANDS/BELGIUM/
LUXEMBOURG
Yamaha Music Europe Branch Benelux
Clarissenhof 5-b, 4133 AB Vianen, Netherlands
Tel: 0347-358 040
FRANCE
Yamaha Music Europe
7 rue Ambroise Croizat, Zone d'activites Pariest,
77183 Croissy-Beaubourg, France
Tel: 01-64-61-4000
ITALY
Yamaha Music Europe GmbH, Branch Italy
Viale Italia 88, 20020 Lainate (Milano), Italy
Tel: 02-935-771
SPAIN/PORTUGAL
Yamaha Music Europe GmbH Ibérica, Sucursal
en España
Ctra. de la Coruna km. 17,200, 28231
Las Rozas (Madrid), Spain
Tel: +34-91-639-88-88
GREECE
Philippos Nakas S.A. The Music House
147 Skiathou Street, 112-55 Athens, Greece
Tel: 01-228 2160
SWEDEN
Yamaha Music Europe GmbH Germany filial
Scandinavia
J. A. Wettergrensgata 1, Box 30053
S-400 43 Göteborg, Sweden
Tel: +46 31 89 34 00
DENMARK
Yamaha Music Europe GmbH, Tyskland – filial
Denmark
Generatorvej 6A, DK-2730 Herlev, Denmark
Tel: 44 92 49 00
FINLAND
F-Musiikki Oy
Kluuvikatu 6, P.O. Box 260,
SF-00101 Helsinki, Finland
Tel: 09 618511
NORWAY
Yamaha Music Europe GmbH Germany -
Norwegian Branch
Grini Næringspark 1, N-1361 Østerås, Norway
Tel: 67 16 78 00
ICELAND
Skifan HF
Skeifan 17 P.O. Box 8120, IS-128 Reykjavik,
Iceland
Tel: 525 5000
RUSSIA
Yamaha Music (Russia) LLC.
Room 37, bld. 7, Kievskaya street, Moscow,
121059, Russia
Tel: 495 626 5005
OTHER EUROPEAN COUNTRIES
Yamaha Music Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: +49-4101-3030
SOUTH AFRICA
Global Music Instruments
Unit 4, 130 Boeing Road East Bedfordview 2008
Postnet Suite 130, Private Bag X10020 Edenvale
1610, South Africa
Tel: 27-11-454-1131
OTHER AFRICAN COUNTRIES
Yamaha Music Gulf FZE
LOB 16-513, P.O.Box 17328, Jebel Ali,
Dubai, United Arab Emirates
Tel: +971-4-881-5868
TURKEY/CYPRUS
Yamaha Music Europe GmbH
Merkezi Almanya Türkiye İstanbul Şubesi
Maslak Meydan Sokak No:5 Spring Giz Plaza
Bağımsız Böl. No:3, 34398 Şişli, İstanbul
Tel: +90-212-999-8010
OTHER COUNTRIES
Yamaha Music Gulf FZE
LOB 16-513, P.O.Box 17328, Jebel Ali,
Dubai, United Arab Emirates
Tel: +971-4-881-5868
THE PEOPLE’S REPUBLIC OF CHINA
Yamaha Music & Electronics (China) Co.,Ltd.
2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu,
Shanghai, China
Tel: 021-6247-2211
HONG KONG
Tom Lee Music Co., Ltd.
11/F., Silvercord Tower 1, 30 Canton Road,
Tsimshatsui, Kowloon, Hong Kong
Tel: 2737-7688
INDIA
Yamaha Music India Pvt. Ltd.
Spazedge building, Ground Floor, Tower A, Sector
47, Gurgaon- Sohna Road, Gurgaon, Haryana, India
Tel: 0124-485-3300
INDONESIA
PT. Yamaha Musik Indonesia (Distributor)
Yamaha Music Center Bldg. Jalan Jend. Gatot
Subroto Kav. 4, Jakarta 12930, Indonesia
Tel: 021-520-2577
KOREA
Yamaha Music Korea Ltd.
8F, 9F, Dongsung Bldg. 158-9 Samsung-Dong,
Kangnam-Gu, Seoul, Korea
Tel: 02-3467-3300
MALAYSIA
Yamaha Music (Malaysia) Sdn., Bhd.
No.8, Jalan Perbandaran, Kelana Jaya, 47301
Petaling Jaya, Selangor, Malaysia
Tel: 03-78030900
PHILIPPINES
Yupangco Music Corporation
339 Gil J. Puyat Avenue, P.O. Box 885 MCPO,
Makati, Metro Manila, Philippines
Tel: 819-7551
SINGAPORE
Yamaha Music (Asia) Private Limited
Block 202 Hougang Street 21, #02-00,
Singapore 530202, Singapore
Tel: 65-6747-4374
TAIWAN
Yamaha Music & Electronics Taiwan Co.,Ltd.
3F, No.6, Section 2 Nan-Jing East Road, Taipei,
Taiwan R.O.C.
Tel: 02-2511-8688
THAILAND
Siam Music Yamaha Co., Ltd.
3, 4, 15 and 16th floor, Siam Motors Building,
891/1 Rama 1 Road, Wangmai,
Pathumwan, Bangkok 10330, Thailand
Tel: 02-215-2622
VIETNAM
Yamaha Music Vietnam Company Limited
15th Floor, Nam A Bank Tower, 201-203 Cach
Mang Thang Tam St., Ward 4, Dist.3,
Ho Chi Minh City, Vietnam
Tel: +84-8-3818-1122
OTHER ASIAN COUNTRIES
Yamaha Corporation
Market Development Section
Nakazawa-cho 10-1, Naka-ku, Hamamatsu,
Japan 430-8650
Tel: +81-53-460-2312
AUSTRALIA
Yamaha Music Australia Pty. Ltd.
Level 1, 99 Queensbridge Street, Southbank,
Victoria 3006, Australia
Tel: 3-9693-5111
NEW ZEALAND
Music Works LTD
P.O.BOX 6246 Wellesley, Auckland 4680,
New Zealand
Tel: 9-634-0099
COUNTRIES AND TRUST
TERRITORIES IN PACIFIC OCEAN
Yamaha Corporation
Market Development Section
Nakazawa-cho 10-1, Naka-ku, Hamamatsu,
Japan 430-8650
Tel: +81-53-460-2312
NORTH AMERICA
CENTRAL & SOUTH AMERICA
EUROPE
AFRICA
MIDDLE EAST
ASIA
OCEANIA
DMI7
C.S.G., Digital Musical Instruments Division
© 2012-2013 Yamaha Corporation
306MWAP*.*-C0
Printed in Vietnam
ZA83740
Yamaha Global Site
http://www.yamaha.com/
Yamaha Manual Library
http://www.yamaha.co.jp/manual/
Yamaha Downloads
http://download.yamaha.com/
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117

Yamaha CVP-605 de handleiding

Categorie
Synthesizer
Type
de handleiding
Deze handleiding is ook geschikt voor