Documenttranscriptie

Getting Started Owner's Manual 1  Getting Started Owner’s Manual 1  Getting Started Contents Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 About the Manuals . . . . . . . . . . . . . . . . . . . . . . . 6 ■ ■ ■ The Getting Started Manual (this manual) . . . . . . . . . . . . . . . . . . . . . . . . 6 The Feature Reference Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 VL1 Basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Essential Concepts for the VL1 User ■ ■ ■ What Are the Advantages? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 The VL1 Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 The Instrument . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 The Controllers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 The Modifiers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 There’s More … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 The Controls & Connectors . . . . . . . . . . . . . . . 16 A Brief Introduction To the VL1 Interface ■ ■ Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Setting Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 System Connections & Preparation ■ ■ ■ ■ ■ ■ ■ ■ Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Controllers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Breath Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Foot Controllers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Foot Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Audio Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Headphones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Stereo Sound System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 MIDI Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Power-on Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Play the Demo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Breath Controller Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Load the Pre-programmed Voice Data . . . . . . . . . . . . . . . . . . . . . . . . . . 31 2  Getting Started Voice Selection . . . . . . . . . . . . . . . . . . . . . . . . . 34 Selecting & Playing the VL1’s 128 Voices ■ ■ Using the Voice Directory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 The Pre-programmed VL1 Voices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 The Controllers . . . . . . . . . . . . . . . . . . . . . . . . . 38 Natural Musical Nuance and Expressive Control ■ ■ ■ ■ ■ ■ Physical Controllers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 VL1 Controller Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Controller Views . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Some Exercises With the AltoSax Controllers . . . . . . . . . . . . . . . . . . . . 42 Controller Envelopes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Other Controller Views . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Mixing & The Modifiers . . . . . . . . . . . . . . . . . . 48 Creating New Timbres and Original Voices Mixing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 ■ An Exercise: Remix the Pan Pipes Voice . . . . . . . . . . . . . . . . . . . . . . . . 49 The Modifiers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 ■ Harmonic Enhancer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 ■ Dynamic Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 ■ Frequency Equalizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 ■ Impulse Expander . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 ■ Resonator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Effects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Creating the Right Ambience ■ ■ ■ Modulation Effects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Feedback Delay Effects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Reverb Effects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 3  Getting Started Precautions !! PLEASE READ THIS BEFORE PROCEEDING !! ■ Location ■ Handling and Transport Do not expose the instrument to the following conditions to avoid deformation, discoloration, or more serious damage. • Never apply excessive force to the controls, connectors or other parts of the instrument. • Always unplug cables by gripping the plug firmly, not by pulling on the cable. • Disconnect all cables before moving the instrument. • Physical shocks caused by dropping, bumping, or placing heavy objects on the instrument can result in scratches and more serious damage. • Direct sunlight (e.g. near a window). • High temperatures (e.g. near a heat source, outside, or in a car during the daytime). • Excessive humidity. • Excessive dust. • Strong vibration. ■ Cleaning ■ Power Supply • Clean the cabinet and panel with a dry soft cloth. • A slightly damp cloth may be used to remove stubborn grime and dirt. • Never use cleaners such as alcohol or thinner. • Avoid placing vinyl objects on top of the instrument (vinyl can stick to and discolor the surface). • Turn the power switch OFF when the instrument is not in use. • The power supply cord should be unplugged from the AC outlet if the instrument is not to be used for an extended period of time. • Unplug the instrument during electric storms. • Avoid plugging the instrument into the same AC outlet as appliances with high power consumption, such as electric heaters or ovens. Also avoid using multi-plug adaptors since these can result in reduced sound quality and possibly damage. ■ Electrical Interference • This instrument contains digital circuitry and may cause interference if placed too close to radio or television receivers. If this occurs, move the instrument further away from the affected equipment. ■ Turn Power OFF When Making Connections • To avoid damage to the instrument and other devices to which it is connected (a sound system, for example), turn the power switches of all related devices OFF prior to connecting or disconnecting audio and MIDI cables. ■ Data Backup • The VL1 contains a special long-life battery that retains the contents of its internal memory even when the power is turned OFF. The backup battery should last for several years. When the backup battery needs to be replaced “Change battery!” will appear on the display when the power is turned on. When this happens, have the backup battery replaced by qualified Yamaha service personnel. DO NOT ATTEMPT TO REPLACE THE BACKUP BATTERY YOURSELF! ■ MIDI Connections • When connecting the VL1 to MIDI equipment, be sure to use high-quality cables made especially for MIDI data transmission. • Avoid MIDI cables longer than about 15 meters. Longer cables can pick up electrical noise that can causes data errors. 4  Getting Started ■ Service and Modification • Internal memory data can be corrupted due to incorrect operation. Be sure to save important data to floppy disk frequently so you have a backup to revert to if something happens to damage the data in memory. Also note that magnetic fields can damage data on the disk, so it is advisable to make a second back-up copy of disks that contain very important data, and keep backup disks in a safe place away from stray magnetic fields (i.e. away from speakers, appliances containing motors, etc.). • The VL1 contains no user serviceable parts. Opening it or tampering with it in any way can lead to irreparable damage and possibly electric shock. Refer all servicing to qualified YAMAHA personnel. ■ Third-party Software • Yamaha can not take any responsibility for software produced for this product by third-party manufacturers. Please direct any questions or comments about such software to the manufacturer or their agents. ■ Handle Floppy Disks and the Disk Drive With Care • Use only 3.5” 2HD or 2DD type floppy disks. • Do not bend or apply pressure to the floppy disk. Do not open the shutter and touch the surface of the floppy disk inside. • Do not expose the disk to high temperatures. (e.g. direct sunlight) • Do not expose the disk to magnetic fields. Magnetic fields can partially or totally erase data on the disk, rendering the disk unreadable. • To eject a floppy disk, press the eject button slowly as far as it will go then, when the disk is fully ejected, remove it by hand. The disk may not be ejected properly if the eject button is pressed too quickly, or it is not pressed in as far as it will go (the eject button may become stuck in a half-pressed position and the disk extends from the drive slot by only a few millimeters). If this happens, do not attempt to pull out the partially ejected disk. Using force in this situation can damage the disk-drive mechanism or the floppy disk. To remove a partially ejected disk, try pressing the eject button once again, or push the disk back into the slot and then repeat the eject procedure carefully. • Do not insert anything but floppy disks into the disk drive. Other objects may cause damage to the disk drive or the floppy disk. YAMAHA is not responsible for damage caused by improper handling or operation. 5  Getting Started About the Manuals The VL1 comes with two manuals — Getting Started and Feature Reference. The Getting Started Manual (this manual) The Getting Started manual contains seven chapters that take you through essential information and procedures you will need to know to become familiar with your VL1: 1. VL1 Basics [≥ Page 8] Basic concepts you’ll need to understand in order to get the most out of the VL1. 2. The Controls & Connectors [≥ Page 16] Brief descriptions of the VL1 controls and connectors, and their functions. 3. Setting Up [≥ Page 22] System connections, powering up, playing the demo, calibrating the Breath Controller, and loading the pre-programmed voices. 4. Voice Selection [≥ Page 34] Several ways to select and play the VL1’s 128 voices. 5. The Controllers [≥ Page 38] The VL1 controllers and how they can be assigned and edited for optimum control. 6. Mixing & The Modifiers [≥ Page 48] Customizing the sound to suit your own personal needs. 7. Effects [≥ Page 58] An overview of the built-in digital effects that you can use to add depth and ambience to the VL1 sound. We recommend that you go through the chapters in sequence and actually try out the various operations described. Once you’ve gone through the entire Getting Started manual in this way, you should be familiar enough with the VL1 to need only the VL1 Feature Reference manual in future. 6  Getting Started The Feature Reference Manual The Feature Reference manual is the “nuts and bolts” reference for the VL1, individually describing its many functions in detail. The Feature Reference manual is divided into five main sections, each describing the various functions within a particular VL1 edit or utility mode. 1. 2. 3. 4. 5. General Operation [≥ Page 7] Play Mode [≥ Page 13] Edit Mode [≥ Page 21] Utility Mode [≥ Page 151] Appendix [≥ Page 177] Once you have become familiar with the way the VL1 works by going through the Getting Started manual, you should only need to refer to the Feature Reference manual from time to time to get details on functions you’ve never used before, or refresh your memory about functions that you don’t use very often. Each section of the Feature Reference manual has its own table of contents, so you should be able to locate any particular function quickly and easily. Functions and references can also be located by referring to the index at the back of the manual. Conventions The following conventions are used through the VL1 manuals to avoid confusion and make the text easier to read. Buttons & Controls Button and control names used on the VL1 panel appear in the text in capital letters within a border: “the [ button”, for example. Parameter Names Parameter names and other labels which appear on the VL1 display are printed in the courier typeface for easier identification: for example, “adjust the “Balance” parameter as required”. Parameter Ranges An ellipsis is used to indicate a range of parameter values: e.g. “0 … 127”. This minimizes the confusion sometimes caused by the use of a hyphen or dash for this purpose. 7  Getting Started VL1 Basics Essential Concepts for the VL1 User T he Yamaha VL1 Virtual Acoustic Synthesizer produces sound in an entirely new way. It has no oscillators or function generators, no preset waveforms or samples. In fact, it uses none of the sound generation concepts employed in conventional synthesizers. The VL1 represents the world’s first practical application of computer-based “physical modeling” in musical sound synthesis. In the same way that computer models are used to simulate weather systems or the flight characteristics of aircraft in the design stage, the VL1 simulates the very complex vibrations, resonances, reflections and other acoustic phenomena that occur in a real wind or string instrument. This requires a tremendous amount of computer processing power (weather and aerodynamic modeling require room-filling super computers), and radical advances in microprocessor speed and capability plus some very sophisticated Yamaha technology were necessary to achieve the real-time sound generation capabilities exhibited by the ground-breaking VL1 Virtual Acoustic Synthesizer. 8  Getting Started What Are the Advantages? T he VL1 offers many advantages in terms of musical performance. Not just in terms of sound, but also in terms of the “behavior” that makes acoustic instruments so … well, musical! But this is not because someone has programmed a certain sound or pattern of behavior into it. The physical model can be programmed to have certain attributes — the length of a pipe or the stiffness of a reed, for example — but the actual sound produced by any configuration can only be accurately determined by playing it. Of course, the same applies to the design of acoustic instruments. Because of its natural acoustic behavior the VL1 is undoubtedly a little harder to play than conventional synthesizers, but when mastered this is the very characteristic that is its greatest strength. The Yamaha VL1 is the most musical synthesizer ever made. A soloist’s dream! • The VL1 sounds better, has more depth, and is more realistic in the musical sense than any other synthesizer system. • Simply pressing a key in the same way does not always produce precisely the same sound. The instrument is responsive and “alive”. • Note-to-note transitions have the same continuity exhibited by acoustic instruments. What goes on in between the notes is just as important musically as the notes themselves. • It has extraordinary expressive capability. Rather than simply controlling parameters like volume or pitch, you can control characteristics such as breath and reed pressure with appropriate complex effects on the timbre of the sound. 9  Getting Started The VL1 Model T he overall VL1 model or “algorithm” consists of three main blocks: the instrument, controllers, and modifiers. In schematic form these blocks are arranged as follows: One VL "Element" (the VL has 2 of these) Controllers (also envelopes) Instrument Modifiers Sound out. ● The Instrument The key block in this algorithm is the instrument, since it is here that the fundamental tone or “timbre” of the sound is defined. The extreme complexity of this portion of the model makes it unsuitable for user programming, so various instruments for the VL1 are provided in the form of pre-programmed voices. These are primarily woodwind, brass, and string voices, since the VL1’s physical model is capable of most accurately simulating the sound-generating mechanism of all three instrument categories. The instrument model consists primarily of a driver — the reed/ mouthpiece, lip/mouthpiece, or bow/string system — and a resonant system corresponding to the tube and air column or string. 10  Getting Started In all these instruments pressure applied here (the driving point) causes vibration which results in sound. Reed vibration. Lip vibration. Air vibration. String vibration. The sound thus produced is amplified and sustained by the body of the instrument. The pitch of the sound is determined by the length of the air column or string, and the timbre is a complex product of the driving source (reed, lip, air, string), the shape of the resonant cavity, the materials from which the instrument is made, etc. One of the remarkable features of the VL1’s Virtual Acoustic Synthesis system is that just about any driver can be used with any type of pipe or string. Drivers Pipes/String 11  Getting Started ● The Controllers The input to an acoustic instrument comes from the player’s lungs, trachea, oral cavity, and lips. In a string instrument it comes from the players arm movement, transmitted to the string via a bow. These elements actually form an important part of the sound generating system and, in the VL1 model, are included in the controllers block. The player also influences the sound of the instrument by playing the keys, tone holes, or frets, and this aspect of control constitutes another part of the controllers block. These and other control parameters provided by the VL1 are listed in the illustration below. In essence, the controller parameters determine how the instrument “plays”. All of these parameters can be assigned to any of the external controllers that can be used with the VL1: breath controller, foot controller, modulation wheels, etc. The pressure parameter, for example, will normally be assigned to a breath controller so the player can control the dynamics of the instrument by varying the breath pressure applied to the controller — a natural, instinctive way to play wind-instrument voices. At the same time the growl and throat parameters might also be assigned to the breath controller in order to achieve life-like response and effects. Throat Controls the characteristics of the "player's" throat or bowing arm. Growl Pressure A periodic pressure (bow velocity) modulation which produces the "growl" effect often heard in wind instruments. The amount of breath pressure applied to the reed or mouthpiece, or bow velocity applied to the string". Embouchure Tonguing The tightness of the lips against the reed or against each other, or the force of the bow against the string. Simulates the half-tonguing technique used by saxophone players by changing the "slit" of the reed. Pitch Scream Changes the length of the air column or string, and thereby the pitch of the sound. Drives the entire system into chaotic oscillation, creating effects that can only be achieved with physical modelling technology. Damping & Absorption Simulate the effects of air friction in the pipe or on the string, and of high-frequency losses at the end of the pipe or string. 12  Getting Started ● The Modifiers Although you don’t have direct programming access to the VL1 instrument block, the modifiers allow a significant degree of control over the final timbre of the voice. The modifiers block consists of 5 sections as shown in the diagram. Although these may appear to be simple effects, they are actually intimately related to the VL1’s sound-producing model and have a significant effect on the sound (the VL1 has a separate effects stage with reverb, delay, and modulations effects — see page 58). Harmonic Enhancer The Harmonic Enhancer allows you to manipulate the harmonic structure of the sound to the extent that you can create radical timbral variations within the current instrument “family” (e.g. saxes). [Page 51] Dynamic Filter This section is similar to the dynamic filters found in many conventional synthesizers. It has selectable high-pass, bandpass, band elimination, and low-pass modes, and a “wet/dry” balance parameter which allows delicate variations in the degree of filtration applied. Another important feature is keyboard cutoff tracking which varies the cutoff frequency according to the key played. [Page 54] Frequency Equalizer This is a 5-band parametric equalizer with frequency, Q (bandwidth), and level control. The equalizer also has pre-EQ highand low-pass filters as well as key scaling capability for precise response control throughout the instrument’s range. [Page 55] 13 In Harmonic Enhancer Dynamic Filter Frequency Equalizer Impulse Expander Resonator Out  Getting Started Impulse Expander The Impulse Expander works in conjunction with the Resonator, described below, to simulate the effect of an instrument’s resonant cavity or sound box. It can also be used to simulate the acoustic environment in which the instrument is played. In contrast to the Resonator, the Impulse Expander is more suited to the simulation of metallic resonances and is thus invaluable for refining the sound of brass and metal-bodied woodwinds. Other important effects are the ability to diffuse sharp attack sounds and to give depth and realism to vibrato. [Page 56] Resonator While the Impulse Expander and even the Harmonic Enhancer tend to give the sound a metallic quality, the Resonator produces a more woody resonance effect. Careful adjustment of the resonator’s parameters can often bring a not-quite-right voice to life. [Page 57] 14  Getting Started There’s More … I n this brief introduction to VL1 basics we’ve only looked at the central physical model which is the key the VL1’s unprecedented sound and musical performance. There’s actually much more to it. To begin with the VL1 actually has two elements which function as independent physical models. Although it is basically a monophonic solo instrument, this means that the VL1 can produce two notes at once. More commonly the two elements are used as layers of a single voice. Element 1 Controllers Instrument Modifiers Element 2 Effects Controllers Instrument Sound out. Modifiers There’s also an extensive range of other functions and features that are similar to those you may be familiar with from conventional synthesizers. There are, for example, a range of programmable envelopes that can be applied to most of the controllers in addition to real-time player control. And, of course, there’s a comprehensive selection of MIDI, disk, and other utility functions that give the VL1 maximum versatility and convenience. Now that you understand the basics, dive in and find out what the VL1 can really do. 15  Getting Started ● The Controls & Connectors The Controls & Connectors A Brief Introduction To the VL1 Interface The following brief descriptions of the VL1 controls and connectors should help you to understand the overall logic of the interface. q MODE Buttons w C Button e S Button r VOLUME Control t – and ≠ Control Sliders L R 1 2 FOOT CONTROLLER OUTPUT 2 1 FOOT SWITCH OUT MIDI IN THRU @0 Floppy Disk Drive MODE PLAY EDIT UTILITY COPY STORE COMPARE F1 !5 OCTAVE _ VOLUME CS1 F2 F3 F4 F5 F6 F7 CS2 and + Buttons DOWN OCTAVE UP !8 PHONES Jack !9 Breath Controller Jack PITCH PHONES MODULATION 1 MODULATION 2 BREATH !7 “ and ‘ Wheels !6 π Wheel 16 u ¡ through • Function Buttons F8 CONT  Getting Started ● The Controls & Connectors q MODE Buttons The P, E, and U buttons select the corresponding VL1 modes. The PLAY mode lets you select and play voices, the EDIT mode gives you programming access to the VL1’s voice and controller parameters, and the UTILITY mode includes MIDI, disk, system and other functions that are essential for general operation. w C Button This button is used to copy voice parameters for fast, efficient editing. ☛ Feature Reference page 25. e S Button Used to store edited data to an internal memory location. ☛ Feature Reference page 28. y LCD Display & ÷ Control i Data Dial !0 = and - Buttons POWER ON / OFF A B C D E F G H 1 2 3 4 5 6 7 8 E1 E2 E2 ALL MOD FBD REV !2 Bank a through h Buttons DEC INC ELEMENT SELECT EXIT ENTER 9 10 ALL HE E1 EFFECT ON / OFF ELEMENT ON / OFF 11 12 13 14 DF EQ IE RSN 15 !3 Voice Number 1 16 through ^ Buttons MODIFIER ON / OFF !1 ] and [ Buttons !4 Keyboard o Cursor Buttons 17 The Controls & Connectors Front Panel  Getting Started ● The Controls & Connectors r VOLUME Control Adjusts the volume of the sound delivered via the rear-panel OUTPUT L and R jacks as well as the PHONES jack. ☛ Getting Started page 25. t – and ≠ Control Sliders These controls can be assigned to a range of controller parameters for real-time expressive control. ☛ Getting Started page 47. Feature Reference page 19. y LCD Display & ÷ Control This large multi-function liquid crystal display panel shows all parameters and prompts you need to operate the VL1 with optimum ease and efficiency. Use the ÷ (contrast) control located near the lower right-hand corner of the display to achieve the best display visibility (LCD visibility varies greatly with viewing angle and lighting). ☛ Getting Started page 34. Feature Reference page 14. u ¡ through • Function Buttons The functions of these buttons depend on the selected mode. They are used to engage a function indicated on the display immediately above the button, select a page of parameters, scroll through a list of parameters, and more. ☛ Getting Started page 26. Feature Reference page 9. i Data Dial The data entry dial provides a fast, efficient way to cover a broad range of voice numbers when, for example, you’re looking for a voice but don’t know the voice number. It’s also handy for making large value changes in any of the edit modes. The data dial is “speed sensitive”, allowing accurate single step selection when rotated slowly as well as large value “jumps” when rotated quickly. ☛ Getting Started page 35. Feature Reference page 16. o Cursor Buttons These 4 buttons move the “cursor” around the display screen, highlighting the various items that are available for selection or parameters that are available for editing (the VL1 cursor appears as a dark block with inverse characters). ☛ Getting Started page 32. Feature Reference page 10. !0 = and - Buttons Used to select voices and edit parameter values in any of the VL1 edit modes. Either button can be pressed briefly for single stepping in the specified direction, or held for continuous scrolling. These buttons are also used to respond “Yes” or “No” to the “Are you sure?” confirmation prompt when saving, loading data. ☛ Getting Started page 35. Feature Reference page 16. !1 ] and [ Buttons The ] button can generally be used to exit from any sub-mode or function, while the [ button is used to engage a variety of modes and functions. ☛ Getting Started page 27. Feature Reference page 10. 18  Getting Started ● The Controls & Connectors ☛ Getting Started page 35. Feature Reference page 15. !3 Voice Number 1 through ^ Buttons The voice number buttons are used in conjunction with the bank buttons to select any of the VL1’s 128 internal voice memory locations. When editing voice parameters they are also used to select and mute elements, an to turn effects and modifiers on or off. ☛ Getting Started page 35. Feature Reference page 15. !4 Keyboard The VL1 has a 49-key keyboard that is both velocity and after-touch sensitive for broad, intimate expressive control. !5 OCTAVE _ and + Buttons Shift the pitch of the keyboard up or down one octave. A utility “Octave Hold” function (page 153 of the Feature Reference manual) provides two modes: shift only while the button is held, or press once to shift and again to release. MIDI note output data is also shifted. !6 π Wheel This self-centering pitch wheel allows realistic upward and downward pitch bends. !7 “ and ‘ Wheels Can be assigned to any of the VL1’s extensive range of controller parameters for extraordinary expressive control. ☛ Getting Started page 41. !8 PHONES Jack Accepts a standard pair of stereo headphones (1/4" stereo phone plug) for headphone monitoring of the VL1 sound without the need for external amplification equipment. ☛ Getting Started page 23. !9 Breath Controller Jack Plug the Yamaha BC2 Breath Controller supplied with the VL1 in here (an optional BC1 Breath Controller may also be used). ☛ Getting Started page 23. @0 Floppy Disk Drive The VL1’s built-in floppy disk drive allows easy, economical, high-volume storage of voice data. The disk-in-use indicator below the drive slot lights while any disk operation is in progress (NEVER attempt to remove a disk or turn the power off while a disk operation is in progress). The eject button, also below the disk slot, is used to remove disks from the drive. ☛ Feature Reference page 162. 19 The Controls & Connectors !2 Bank a through h Buttons The VL1 has 128 internal voice memory locations arranged in 8 banks of 16 voices each. These buttons select the voice bank from which an individual voice will be selected.  Getting Started YAMAHAMODELVL1 ACINLET ● The Controls & Connectors FOOT SWITCH MIDI THRU OUT IN 2 1 OUTPUT FOOT CONTROLLER 2 1 R L POWER ON / OFF @2 POWER Switch @1 AC Power Cord Socket @6 MIDI IN, OUT and THRU Connectors @3 OUTPUT L and R Jacks @4 FOOT CONTROLLER 1 and 2 Jacks @5 FOOT SWITCH 1 and 2 Jacks Rear Panel @1 AC Power Cord Socket Be sure to plug the VL1’s AC power cord into this socket before plugging the power cord into an AC outlet. ☛ Getting Started page 22. @2 POWER Switch Press to turn power ON or OFF. @3 OUTPUT L and R Jacks These are the main stereo outputs from the VL1. Be sure to connect both outputs to the appropriate channels of a stereo sound system in order to appreciate the full quality of the VL1 sound and effects. ☛ Getting Started page 24. @4 FOOT CONTROLLER 1 and 2 Jacks These jacks accept Yamaha FC7 Foot Controllers which can be used to control any of the VL1’s controller parameters. One FC7 Foot Controller is supplied with the VL1, and this should normally be plugged into the FOOT CONTROLLER 2 jack. The second FC7 foot controller is optional. ☛ Getting Started page 23. @5 FOOT SWITCH 1 and 2 Jacks An optional Yamaha FC4 or FC5 footswitch can be connected to one or both of these jacks for sustain, portamento, and other control functions. ☛ Getting Started page 23. @6 MIDI IN, OUT and THRU Connectors The MIDI IN connector receives the data from an external sequencer or other MIDI device which is to control or transmit data to the VL1. The MIDI THRU connector simply re-transmits the data received at the MIDI IN connector, allowing convenient chaining of MIDI devices. The MIDI OUT connector transmits data corresponding to all VL1 performance operations, or bulk data when one of the MIDI data transmission functions are activated. ☛ Getting Started page 24. 20  Getting Started ● The Controls & Connectors The Controls & Connectors 21  Getting Started Setting Up ● Setting Up System Connections & Preparation Foot Controller Foot Switch MIDI Audio L R 1 2 FOOT CONTROLLER OUTPUT 2 1 FOOT SWITCH OUT MIDI IN POWER ON / OFF THRU MODE PLAY EDIT UTILITY COPY A STORE B C D E F G H COMPARE DEC INC 1 9 10 11 12 13 14 EXIT ENTER ALL H.E. D.F. E.Q. I.E. RES E1 ELEMENT F1 VOLUME DOWN OCTAVE CS1 F2 F3 F4 F5 F6 F7 F8 CONT 2 E2 SELECT 3 E1 ELEMENT MODIFIER CS2 4 5 6 E2 ALL MOD EFFECT ON / OFF 7 8 FBD REV ON / OFF 15 16 ON / OFF UP MAX MIN PITCH MODULATION 1 MODULATION 2 Power Supply Headphones Breath Controller Power Supply Before making any other connections the “female” end of the AC power cord supplied with the VL1 should be firmly plugged into the rear-panel AC cord socket. Ideally the power cord should then be plugged into a convenient AC outlet after you’ve made all other necessary connections and placed the VL1 in the position in which it will be used. Always make sure that the POWER switch is in the OFF (extended) position before plugging the power cord in an AC outlet. CAUTION! CAUTION! ■ Make sure your VL1 is rated for the AC voltage supplied in the area in which it is to be used (as listed on the rear panel). Connecting the VL1 to the wrong AC supply can cause serious damage to the internal circuitry and may even pose a shock hazard! 22  Getting Started ● Setting Up Controllers The Breath Controller is an essential expressive tool — both for realistic expression with wind-instrument voices and unprecedented expressive control with string voices. Plug the BC2 Breath Controller supplied with the VL1 (or an optional BC1 breath controller) into the front-panel breath controller jack. The Breath Controller is ideal for controlling parameters that would normally be affected by a wind player’s breath: dynamics, timbre, pitch, and others. Once you’ve set up your system and begin playing, refer to “Breath Controller Calibration” on page 29 for instructions on calibrating your Breath Controller for optimum control precision and ease. NOTES ■ For more information on Breath Controller setup and operation, see the instructions packed with the supplied BC2 Breath Controller. ● Foot Controllers Although the VL1 has jacks for two foot controllers, it is not necessary to use both. To begin with plug the supplied FC7 Foot Controller into the rear-panel FOOT CONTROLLER 2 jack. If you purchase a second FC7 Foot Controller for extra control capability, plug it into the FOOT CONTROLLER 1 jack. NOTES ■ For more information on Foot Controller setup and operation, see the instructions packed with the supplied FC7 Foot Controller. ● Foot Switches The use of one or two footswitches allows sustain, portamento, and mono/poly mode switching. We recommend that you purchase at least one Yamaha FC4 or FC5 Footswitch for this purpose. A single footswitch can be plugged into either the rear-panel FOOTSWITCH 1 or 2 jack. Audio Connections ● Headphones For private listening and practice headphones are ideal. You don’t have to hook up and complete sound system, and you won’t disturb the neighbors no matter how loud or late you play. Recommended Yamaha headphones for VL1 monitoring are the HPE-170, HPE-160, or HPE-150 Stereo Headphones. Any standard pair of stereo headphones with a 1/4" stereo phone plug and an impedance of between about 8 and 150 ohms can be used. 23 Setting Up ● Breath Controller  Getting Started ● Setting Up ● Stereo Sound System The VL1 voices and effects are designed to sound their best in stereo, so you should always use a stereo sound system to appreciate the full impact of the VL1 voices and expressive features. The VL1 OUTPUT L and R jacks can be connected directly to musical instrument amplifiers designed for keyboard use, or to the line inputs of a mixing console. It is also possible to connect the VL1 outputs directly to the inputs of a multitrack or stereo tape recorder. NOTES ■ If you need to drive a mono amp or other device the VL1 output can be switched to mono — the same signal appears at the L and R outputs — by using the Output parameter described on page 154 of the Feature Reference manual. ■ Make sure that both the VL1 and your sound system are turned OFF when making connections. MIDI Connections Like any other MIDI instrument the VL1 can be used with MIDI tone generators, sequencers, computer software, and controllers for virtually unlimited system expansion and control capability. You might, for example, like to control it from a Yamaha wind controller such as the WX11 rather than the keyboard for even more realistic windinstrument feel and expression. To ensure reliable error-free transmission of MIDI data always use high-quality MIDI cables obtained from your Yamaha dealer or music equipment store. Also avoid MIDI cables that are longer than about 15 meters, since cables longer than this can pick up noise which can cause data errors. The VL1 MIDI transmit channel, receive channel, local on/off, and device number parameters are available in the utility mode “MIDI Setting” page described on page 155 of the Feature Reference manual. Make sure these parameters are set to match the corresponding settings of the external MIDI device(s) used with the VL1. ● The VL1 transmits and receives the following MIDI data: Note The played key(s) and velocity value. Control Change Modulation wheel, foot controller, breath controller, and other controller data. Program Change Voice numbers from 1 to 128. Aftertouch Keyboard aftertouch pressure. Pitch Bend Pitch bend wheel position. Bulk Voice and system parameters transmitted in the form of “bulk dumps”. 24  Getting Started ● Setting Up NOTES ■ For detailed MIDI specifications refer to the “MIDI Data Format” . Power-on Procedure Always follow proper procedure when powering-up a sound system to minimize the possibility of damage to the equipment (and your ears!). 1. Make sure your sound system’s main level/volume control(s) and the VL1 volume control are turned all the way down prior to turning power on. 2. Turn on the VL1. 3. Turn on the sound system. 4. Raise the sound system volume to a reasonable level. 5. Gradually raise the VL1 VOLUME control while playing the keyboard to set the desired listening level. NOTES ■ The VL1 automatically transmits MIDI control change data corresponding to its control status when its power switch is turned ON or OFF. This can interfere with operation of other MIDI equipment connected to the VL1 MIDI OUT connector. If the VL1 is connected to other MIDI equipment, the VL1 power switch should be turned ON first, and turned OFF last. 25 Setting Up ■ When using the VL1 with other MIDI equipment, it is a good idea to refer to the MIDI specifications (implementation chart, MIDI data format) of the equipment used to ensure compatibility.  Getting Started ● Setting Up Play the Demo Once you’ve set up your VL1 system, you might like to play the pre-programmed demo sequence to hear how some of the voices sound. This process will also help to familiarize you with some of the VL1’s selection and editing procedures. IMPORTANT! ■ When you run the demo the VL1 automatically loads the required voices and system data into the 16 bank-H voices, thus erasing any previous data in these memory locations. This is the same as the data initially contained in these memory locations when the VL1 is first shipped, so if you haven’t made any changes there is no problem. If, however, you have edited the bank-H data or saved data from another bank or disk to this bank, you may want to save your data to floppy disk before running the demo. IMPORTANT! 1. Select the Utility Mode System Page Press the U button to select the utility mode. Then, if it is not already selected when the utility mode display appears, press the ¡ button to select the “System” function page. 2. Select the Demo Page Press the ∞ button to select the “Demo” page. 26  Getting Started 3. ● Setting Up Press [ and Confirm 4. Select a Song Use the data dial or = and - buttons to select the song number you want to start with. 5. Run the Demo Press the • button to run the demo. Playback will start with the selected song, then all other songs will be played in sequence. The cycle will repeat until stopped. 27 Setting Up Press the [ button if it’s OK to go ahead with the demo — and rewrite all bank-H data. The VL1 will ask you to confirm again: press - to continue or = to abort.  Getting Started 6. ● Setting Up Stop the Demo Press the ¶ button to stop demo playback. 7. Return To the Play Mode When Done Press the MODE P button to return the PLAY mode. 28  Getting Started ● Setting Up Breath Controller Calibration 1. Make Sure the Breath Controller Is Connected Make sure the breath controller is properly connected: turn the power OFF, plug in the breath controller, then turn the power ON. 2. Select the Utility Mode System Page Press the U button to select the utility mode. Then, if it is not already selected when the utility mode display appears, press the ¡ button to select the “System” function page. 3. Go To the Utility Mode Curve Page and Select “Brth” Use the cursor buttons to move the cursor to “5:Curve”, then press [ to call the “Curve” function page. When the curve display appears press the • function button (“Brth”) to call the breath controller curve page. 4. Adjust the Breath Controller Offset The following adjustment must be performed while not blowing into the breath controller mouthpiece. Do not hold the breath controller in your mouth. Rotate the breath controller OFFSET trimmer slowly clockwise, using the supplied screwdriver, until the vertical cursors above and below the curve graph move slightly to the right and the number below the graph is greater that “0”. Then slowly rotate the trimmer carefully counter-clockwise until the number below the graph just reaches “0” (the cursors will be lined up with the left end of the graph), then stop. This completes the offset adjustment. 29 Setting Up Proper operation of the breath controller is vital to achieving the best possible sound from the VL1. Although the controller is factory-calibrated to match most requirements, we recommend that you carefully calibrate the breath controller for optimum performance with your own playing style.  Getting Started 5. ● Setting Up Adjust the Breath Controller Gain Place the breath controller mouthpiece in your mouth and blow — notice that the cursors move to right and the number below the graph increases according to how hard you blow. Rotate the breath controller GAIN trimmer counter-clockwise as far as it will go (don’t force it!) then, while blowing into the mouthpiece using the maximum pressure you intend to use while playing, rotate the trimmer slowly clockwise until the number below the graph just reaches “127” (the cursors should just line up with the right end of the graph) and then stop. This completes the gain adjustment. NOTES ■ In addition to calibrating the breath controller, the UTILITY mode “Curve” page described here also allows you to select a range of 4 different response curves — these are discussed in more detail on page 157 of the Feature Reference manual. 6. Return to the Play Mode Press the P button to return to the PLAY mode. 30  Getting Started ● Setting Up Load the Pre-programmed Voice Data NOTES ■ Loading the pre-programmed voices overwrites any other data that is in the VL1 internal memory, so if you have any important voices in memory make sure it is safely stored to disk before loading the data — Feature Reference manual, page 166. 1. Insert the Voice Disk Insert the voice disk into the disk drive. The sliding disk shutter should go in first, and the label side of the disk should face upward. 2. Select the Utility Mode System Page Press the U button to select the utility mode. Then, if it is not already selected when the utility mode display appears, press the ¡ button to select the “System” function page. 3. Go To the Miscellaneous Page & Turn Memory Protect Off Use the cursor buttons to move the cursor to “6:Miscellaneous”, then press [ to call the “Miscellaneous” function page. Use the cursor buttons to select the “Memory Protect” parameter, then press = to turn memory protect “off”. 31 Setting Up Although the factory pre-programmed voices, performance combinations, and patterns are stored in the VL1 internal memory when the instrument is initially shipped, there is always a possibility that all or part of the memory has been erased or modified by the time the instrument gets to you. Here’s how you can re-load all the pre-programmed data from the supplied voice disk.  Getting Started 4. ● Setting Up Select the Disk Function Directory Press the £ function button (“Disk”) to select the utility mode disk function directory. 5. Select “Load From Disk” Use the cursor buttons to move the cursor to “2:Load From Disk” and then press [. 6. Select “All” and Select the “CUSTOMER:All” File Make sure the cursor is positioned at “1:All” and press [. When the list of files appears use the cursor > and < buttons to select the “CUSTOMER:All” file, then press [ again. 32  Getting Started 7. ● Setting Up Load the File 8. Return to the Play Mode & Eject the Disk When the “Completed!” display appears, press theP button to return to the play mode, then press the eject button below the disk drive slot to eject the disk. Store the disk in a safe place. You must now select a voice in order for the loaded data to be properly activated — see the following section. About the VL1 Data Disk The floppy disk supplied with the VL1 contains the following files: ● CUSTOMER:ALL A complete set of 128 voices and system data in which the voices are programmed to allow maximum controller variation. The MODULATION 2 wheel should be at its center position for “normal” sound. ● FACTORY:ALL A complete set of 128 voices and system data in which the voices are programmed for easy playability — the controller range is not as broad as the CUSTOMER.ALL voices. ● EXAMPLE:ALL Some example voices in which the controller settings are emphasized. 33 Setting Up Loading will begin when you press the - button in response to the “Are You Sure?” prompt. A bar graph on the display will indicate the progress of the load operation, and when all the data has been loaded “Completed!” will appear.  Getting Started ● Voice Selection Voice Selection Selecting & Playing the VL1’s 128 Voices One of the first things you’ll want to do with your VL1 is select and play some of its voices … this section will show you how to do just that. 1. Select the Play Mode Press the P button so that its indicator lights and the word “PLAY” appears in the upper left corner of the LCD panel. A considerable amount of information appears on the play-mode display in addition to the name of the currently selected voice. Many of the functions relating to this information will be covered later in the manual. For now, here are the basics: Voice name: Alto Sax Voice B02 (no. 18 of 128). Play mode. Reverb is ON. Stereo output mode. Element E1 name: Alto Sax Mono voice, using a single element. Effects in use: Pitch Change, Feedback Delay off and Studio type reverb. The abbreviations in the section separated by a line at the bottom of the display (“Cnt1”, “Cnt2”, etc) indicate the functions of the corresponding function buttons below the display: ¡ through •. These will be discussed later in this section. 34  Getting Started 2. ● Voice Selection Select a Voice To select a different voice within the same bank it is only necessary to press the appropriate voice number button. To select a different bank, however, you’ll always have to press both a bank button and a voice number button (or the [ button). This prevents unwanted voices from being selected until you’ve actually specified both the bank and number of the voice you want to use. Alternate Voice Selection Methods ● The - and = Buttons are best used for small, step-wise changes — e.g. selecting adjacent voice numbers, or numbers that are only a few steps away. Press the = or - button briefly to decrement or increment the voice number by one, or hold either button for continuous DEC INC decrementing or incrementing in the corresponding direction. The bank will switch automatically if you cross a bank voicenumber boundary. ● The Data Dial provides a fast, efficient way to cover a broad range of voice numbers when, for example, you’re looking for a voice but don’t know the voice number. Simply rotate the data dial clockwise for higher voice numbers or counter-clockwise for lower voice numbers while watching the display. The banks are automatically switched when necessary as the voice numbers are changed. 35 Voice Selection The VL1’s 128 voices are organized into 8 banks of 16 voices each (8 x 16 = 128). Any voice can be selected by specifying its bank using the bank buttons (a through h), and its number using the voice number buttons (1 through ^). To select voice “B2”, for example, first press the bank b button and then the voice number 2 button. The bank b button indicator will flash until the voice number 2 button is pressed and the B2 voice is actually engaged. Note that when you select a different bank (or even press the current bank button) the voice directory for the selected bank will appear on the display, showing the names of all voices in that bank with the cursor located at the currently selected voice number. The VL1 returns to the normal voice display as soon as you specify the voice number. You can also press the [ button if you want to stay with the same voice number.  Getting Started 3. ● Voice Selection Play Try playing the selected voice on the keyboard. Select a number of different voices and try them out. You will have to apply breath pressure to the breath controller, press the foot controller forward, or roll the ‘ wheel upward to produce sound with many of the VL1’s voices. A complete list of the pre-programmed voices and their controller assignments is provided in the Voice List & MIDI Data Format. A brief voice list is provided below. The VL1 also provides “controller views”, described in the next chapter, that let you check the current controller assignments via the VL1 display. NOTES ■ If you don’t get any sound at this point: Make sure your sound system is turned ON and the volume is turned up to a reasonable level, make sure that the VL1 VOLUME control is turned up to a reasonable level, and check all connections carefully. Using the Voice Directory Although the voice directory appears automatically any time you select a different bank, you can have the directory displayed continuously if you find it more convenient than the normal voice display. To switch to the voice directory display, press the • button — located directly below “Dir” on the display. Voices are selected using the same methods described in the preceding section, and the cursor buttons or data dial will move to the selected voice. To return to the normal voice display press the ] button. 36  Getting Started ● Voice Selection The Pre-programmed VL1 Voices Here’s an abbreviated voice list for easy reference. Voice Name Voice No. Voice Name Voice No. Voice Name Voice No. Voice Name A01 (001) A02 (002) A03 (003) A04 (004) A05 (005) A06 (006) A07 (007) A08 (008) A09 (009) A10 (010) A11 (011) A12 (012) A13 (013) A14 (014) A15 (015) A16 (016) Moby Tenor Sax Shakuhachi FingerBass Trumpet Ossyncro Tull Flute Bagpipes GuitarHero Mizu Horne Viol Inn Endophone JetLipBow BowBamBoo Bassoon Digeritek C01 (033) C02 (034) C03 (035) C04 (036) C05 (037) C06 (038) C07 (039) C08 (040) C09 (041) C10 (042) C11 (043) C12 (044) C13 (045) C14 (046) C15 (047) C16 (048) Gonzilla Soprano 1 MouthKeys Thump Bass Cornet Igneous Alto Flute Khaen Cruncher Marsaloboe Eleanor RichReed Breath Bow SquealerAT Oboe Maysbe? E01 (065) E02 (066) E03 (067) E04 (068) E05 (069) E06 (070) E07 (071) E08 (072) E09 (073) E10 (074) E11 (075) E12 (076) E13 (077) E14 (078) E15 (079) E16 (080) Dr.Bonky Bell Miked Blues Harp Slap Bass Muted Lips Analunar Andean Sitar Rock Pigs Synth Lite St. Ripper Scat Harp L7 Pluck Flak 3 AM Blow Yamasteel G01(097) G02(098) G03(099) G04(100) G05(101) G06(102) G07(103) G08(104) G09(105) G10(106) G11(107) G12(108) G13(109) G14(110) G15(111) G16(112) Lees Breath Sax Bowed Saw Birdland Fanfare Chalsaw Recorder Harmonium WonderBass NuDblReed Viowind Harmoweird Cyberpluck NuAltoPipe Gerhard Mad Tube B01 (017) B02 (018) B03 (019) B04 (020) B05 (021) B06 (022) B07 (023) B08 (024) B09 (025) B10 (026) B11 (027) B12 (028) B13 (029) B14 (030) B15 (031) B16 (032) Backwards Alto Sax Pan Pipes MelodyBass Horn 50 / 50 C Flute HurdyGurdy JazzGuitar Harmophone Fiddler Floboe Yhokihi BlueBottle Clarinet Jurassic D01 (049) D02 (050) D03 (051) D04 (052) D05 (053) D06 (054) D07 (055) D08 (056) D09 (057) D10 (058) D11 (059) D12 (060) D13 (061) D14 (062) D15 (063) D16 (064) BlownDrone Loose Bari Toots Fretless Tuba Arpoon Piccolo Thai Reed Frange NuSoprPipe Contraire ClariLip Conchise Pastorale Barker FrenchBone F01 (081) F02 (082) F03 (083) F04 (084) F05 (085) F06 (086) F07 (087) F08 (088) F09 (089) F10 (090) F11 (091) F12 (092) F13 (093) F14 (094) F15 (095) F16 (096) MoreGrunge Soprano 2 Ocarina Upright Alto&Trump OldMini Fyfe Squeezebox Mr. Mogue HyperClari DoubleBow RuffWreck Clavisynth Claricord TrumpNSax QuiScivit? H01 (113) H02 (114) H03 (115) H04 (116) H05 (117) H06 (118) H07 (119) H08 (120) H09 (121) H10 (122) H11 (123) H12 (124) H13 (125) H14 (126) H15 (127) H16 (128) AcoEkoSyn LooseTenor Kokyu Tube Bass TrumpCard PipeBowBow BaroquePad Outback FuzzyBass Wheed Monteverdi Sax Git Cyberisen Clar&Flute Saxes Isn’t Wah A more detailed voice list is provided in the Voice List & MIDI Data Format. 37 Voice Selection Voice No.  Getting Started ● The Controllers The Controllers Natural Musical Nuance and Expressive Control If you’ve read the “VL1 Basics” section (if you haven’t, please do so — page 8) you should understand the concept of “controllers” as applied to the VL1. The “controller parameters” correspond to simulated characteristics of the instrument model — e.g. breath pressure, embouchure or tonguing. Any of these can be controlled by you via “physical controllers” — e.g. the breath controller or modulation wheel — assigned to the required controller parameter. Even if you never go as far as editing the actual sound of the voices, you’ll no doubt want to be able to change these controller assignments and modify the way the controllers affect the sound. In this section we’ll introduce you to the basics of controller assignment and operation. Physical Controllers "Physical controllers" such as the Breath or Foot Controller can be assigned to "controller parameters" such as Pressure or Embouchure. • Breath Controller • Foot Controller • Etc. VL Controller Parameters • Pressure • Embouchure • Etc. The effectiveness of the VL1 as a musical instrument depends to a great deal on how well you learn to use these controllers. Since the VL1 sound is produced by a computer-based physical model rather than a oscillator-based tone generator, there are no hard-and-fast rules as to how any controller will actually affect the sound. There are guidelines, based on the role of the corresponding controller parameter within the physical model, but proficiency with the VL1 depends more on experience and practice — just as it does in any acoustic instrument. 38  Getting Started ● The Controllers Physical Controllers First, here’s a list of the physical controllers available for use with the VL1: A natural candidate for controlling pressure, tonguing, throat, growl, and other parameters. Breath Attack This unique “controller” can be applied only through the Breath Controller. When it is selected control is applied by changes in breath pressure, rather than the absolute breath pressure itself. A constant pressure — whether zero or maximum — produces no change. The faster the change in pressure, the higher the control value. Pitch Wheel The self-centering VL1 pitch wheel can be assigned to a range of parameters, but it’s “standard” function is pitch control. A controller parameter such as Embouchure can also be assigned to the pitch wheel for more realistic pitch variations. Modulation 1 Wheel This wheel produces minimum effect in its lowest position and maximum effect in the highest position. This modulation wheel is permanently assigned to the standard MIDI modulation wheel control change number — 001. Modulation 2 Wheel The VL1’s second modulation is not self-centering, but it has a center click-stop which makes it ideal for assignment to parameters that have a “normal” central setting with variations above and below. It can also be assigned to any MIDI control change number, function in the same way as the breath controller, foot controller, etc. Foot Controller 1 Foot controller 1 has the standard MIDI foot controller control change number — 004 — and can be assigned to any VL1 controller parameter. Foot Controller 2 Like the modulation 2 wheel, foot controller 2 is assignable to any MIDI control change number, and is frequently assigned to function in the same way as the breath controller. It can also be assigned to any VL1 controller parameter. Foot Switches 1 & 2 In addition to their obvious sustain and portamento functions, the foot switches are independently assignable to any MIDI controller function as well as a voice number increment function. Of course, they are only really useful with on/off type parameters — not with parameters that allow continuous control. Aftertouch Keyboard aftertouch allows you to control any controller parameter by the pressure you apply to a key after it is initially pressed. This is perhaps the most “intimate” type of keyboard expression control. Velocity Although normally assigned to pressure (particularly in plucked string voices), keyboard velocity can also be assigned to any other controller parameter. MIDI The MIDI protocol provides 119 control change numbers, some of which are pre-assigned to specific controllers — “001” is “Modulation Wheel”, for example. All of these are available for assignments to the VL1 controller parameters, so external MIDI control devices can be used to full advantage. 39 The Controllers Breath Controller  Getting Started ● The Controllers VL1 Controller Parameters Any of the physical controllers listed above can be assigned to control any of the VL1’s controller parameters: Pressure The amount of breath pressure applied to a reed or mouthpiece, or the speed of the bow applied to a string. Pressure variations affect both volume and timbre. Embouchure The tightness of the lips against the reed or against each other. In a string instrument voice Embouchure corresponds to how strongly the bow is pressed against the string. Affects both pitch and timbre. Pitch Changes the length of the air column, and thereby the pitch of the sound. The PITCH wheel is usually assigned to this parameter. Vibrato A standard vibrato (pitch modulation) effect. An extensive range of parameters makes it possible to achieve extremely natural vibrato effects. The amounts of vibrato applied via pitch and embouchure, for example, are independently programmable. Tonguing Simulates the half-tonguing technique used by saxophone players by changing the “slit” of the reed. The slit is the space between the tip of the reed and the mouthpiece. Amplitude Unlike Pressure, this parameter simply controls the volume of the sound without varying timbre. Scream Drives the entire system into chaotic oscillation, creating effects that can only be achieved with physical modeling technology. Breath Noise Adds breath noise. The sound of the breath noise itself can be varied over a wide range using the EDIT mode “Breath Noise” parameters — Feature Reference manual page 73. Growl A periodic pressure modulation which produces the “growl” effect often heard in wind instruments. Like vibrato, an extensive range of parameters allow remarkably realistic effects. Throat Formant Controls the characteristics of the simulated player’s lungs, trachea, and oral cavity. Can add a realistic “roughness” to the sound. Dynamic Filter Similar to the dynamic filters found in many conventional synthesizers. The VL1 filter has selectable high-pass, bandpass, band elimination, and low-pass modes. Harmonic Enhancer The Harmonic Enhancer can vary the harmonic structure of the sound over a wide range. The Harmonic Enhancer also includes parameters that affect breath noise and several reed characteristics. Damping Simulates the effect of damping at the end of the air column or string. Affects both pitch and timbre. Absorption Similar to the above, but simulating the effect of absorption at the end of the air column or string. In the case of a wind instrument, the Damping and Absorption parameters control the diameter and shape of the bell. 40  Getting Started ● The Controllers Controller Views In the PLAY mode, function buttons ¡ through § are used to select “controller view” displays that list all controller assignments for the currently selected voice. In particular, ¡ through ¢ display the assignments for the controller parameters listed in the preceding chart (you can press the ] button at any time to return to the normal play-mode display). The Controllers ¡ ™ £ ¢ The controller parameters are listed in the left column of the controller view display, and the controllers assigned to them are listed in the center column. Note that the right column is empty. This is because the AltoSax voice used for this example only uses one element, so the controllers are listed in the central “Element1” column. In a voice that uses two elements the “Element2” controllers are independently assignable and are listed in the right column. In this example we can see that the breath controller is assigned to control “Pressure” and “H.Enhancer” (the Harmonic Enhancer). The pitch wheel controls both “Pitch” and “Embouchure”, and the modulation wheel (MODULATION 1) controls “Vibrato”. Keyboard aftertouch controls the “Throat” parameter. The remaining parameters are currently “off” and therefore have no effect on the sound. NOTES ■ The ∞ (“Cnt5”) and § (“CS”) function buttons access controller views that deal with different types of controllers. These will be summarized in the “Other Controller Views section on page 47 of this manual. 41  Getting Started ● The Controllers Some Exercises With the AltoSax Controllers Now that you know which physical controllers are assigned to which controller parameters in the AltoSax voice, play the voice using the assigned controllers to get a feel for their effect before changing the assignments. 1. Engage the EDIT Mode The controller assignments are accessed via the EDIT mode Controller page. To get to this page first press the [ button to engage the edit mode. This is the initial EDIT mode display: If the initial EDIT mode display shown above does not appear when the E button is pressed, try pressing the ] button one or more times. NOTES ■ When the edit mode is selected, the VL1 will automatically go straight to the last edit page that was selected for maximum programming speed and efficiency. You may have to ] through one or two layers of the EDIT mode display hierarchy to return to the initial display. 2. Select the Element 1 Controller Parameters Press the ™ function button (immediately below “E1” on the display) to select the element-1 parameters (“E2” also becomes available for access via £ when editing a voice that uses two elements). If the display doesn’t look like this press the ¡ function button (below “Ctrl” on the display) to call the “Controllers” page. 3. Select the Controller Parameter You Want To Edit Use the cursor buttons to select the controller parameter you want to assign a controller to (you can also use the = and - buttons or data dial for this), then press the [ button. For example, let’s try adding scream control to the MODULATION 1 wheel (it currently controls vibrato). Move the cursor to “07:Scream” and press[. 42  Getting Started The Controllers Edit the Scream Controller Parameter The cursor should be located at the “Controller” parameter, as shown in the example display. In the AltoSax voice the scream control parameter is not used so it is currently turned “off”. Press the - button or rotate the data entry dial to the right slightly to select “Modulation Wheel”, the first controller on the list. Notice that as soon as you edit the parameter, an inverse letter “E”(´) appears to the left of the voice number near the upper left corner of the display. This tells you that the voice has been edited and, later, that you’ll need to store the voice in memory before selecting a different voice if you want to keep the edited data. NOTES ■ The Controller parameter has 124 settings — corresponding to the 124 controller number provided by MIDI protocol. Some of these are preassigned: Modulation Wheel is number 001, Breath Controller is number 002, etc. When you select a pre-assigned controller the corresponding controller name is shown on the display; non-assigned controllers are displayed as MIDI control change numbers. ■ The “Modulation Wheel” setting refers to the VL1’s MODULATION 1 wheel. The MODULATION 2 wheel can be assigned to any MIDI control change number. 5. Try Out the Edited Voice & Cancel the Vibrato Effect Try operating the “ wheel while playing the AltoSax voice. You should hear the scream effect increase as the wheel is rolled upward. Vibrato is still assigned to the “ wheel, so the vibrato effect will come in simultaneously. To cancel the vibrato effect and leave only the scream effect, simply go to the Controller “VIBRATO” page and turn the Controller parameter “off”. To get to the vibrato page you can either ] to the controller directory introduced in step 2 and select the vibrato page from there, or step backward through the controller pages by using the § function button (“Bpag” stands for “Back page”). In the same way, the ¶ function button can be used to step forward through the controller pages (“Fpag”). NOTES ■ When “Para” appears above the • function button, as it does in the vibrato and several other controller pages, the • function button accesses another page of parameters pertaining to the controller. 43 The Controllers 4. ●  Getting Started 6. ● The Controllers Go to the Pressure Controller Page From the Vibrato page use the § button to step back to the Pressure controller page. Quite logically, the Breath Controller is assigned to control the “Pressure” parameter, and we will leave it set that way while we experiment with the “Depth” and “Curve” parameters. 7. Vary the Depth Parameter Move the cursor to the “Depth” parameter and, while trying out the effect of the changes on how the “Pressure” parameter is affected by the Breath Controller, use the data dial to vary to depth setting. As you decrease the setting, notice that the graph to the right of the display changes accordingly. The horizontal axis corresponds to breath pressure (or the control value in any other controller screen), and the vertical axis represents the depth of the parameter. With “Depth” set to the maximum value of “127” no breath pressure produces no sound and maximum breath pressure produces maximum output. Maximum output. 127 Minimum output. 0 0 Minimum breath pressure. 127 Maximum breath pressure. As the value of the “Depth” parameter approaches zero, however, the depth of the output range is reduced and a corresponding amount of output is produced even at minimum breath pressure. In other words, at a setting lower than 127 simply playing a key will produce sound even without breath pressure, and the Breath Controller will vary output between the initial level and maximum output. 44  Getting Started ● The Controllers Once you pass zero, you enter a range of “negative” Depth values that produce reverse controller operation: i.e. the output level decreases as you blow harder into the Breath Controller. Like the normal positive range, the negative Depth range is from “0” to “-127”. 8. Vary the Curve Parameter You may have noticed in the previous step that the relationship between breath pressure and output is linear. That is, a change in breath pressure produces a corresponding change in sound. The “Curve” parameter makes it possible to change that relationship. As you increase the curve value (the maximum value is 16), the line on the graph which represents breath pressure versus output will curve downward, as shown in the display below (setting “12”). The result is that the lower end of the breath pressure range has relatively little effect on the sound, while higher breath pressures produce more dramatic changes. Negative curve values (0 … -16) have the opposite effect: Output increases rapidly at low breath pressures while higher pressures produce relatively little effect. 45 The Controllers NOTES ■ Many parameters with any relationship to MIDI control have a range of values from -127 through 0 to 127 (255 steps). This corresponds to the range of values that can be represented in binary form by one “byte” (8 bits) of data — the number MIDI uses to convey control values.  Getting Started 9. ● The Controllers Experiment! Now that you’ve got the idea, flip through the all the available controller pages and experiment with alternative assignments and settings until you feel comfortable with the system. You should also try this with different voices later, since the controllers can have different effects with different voices. NOTES ■ There are several variations on the basic controller display and parameters. When you’re ready to study the parameters in more detail refer to the “Element Controllers” section beginning on page 64 of the Feature Reference manual. 10. Return to the Play Mode When Done When you’re finished experimenting with the controllers, press the P button to return to the play mode. Note that the inverse letter “E”(´) still appears to the left of the voice number, indicating that the voice has been edited. If you want to keep the edited voice, it must be saved either to an internal memory location or to floppy disk, as described on pages 28 and 166 of the Feature Reference manual, respectively. This must be done before you select a different voice (or the same voice again) or your edits will be lost. To confirm this, try selecting a different voice and then return to the AltoSax voice … the inverse “E”(´) will be gone and the voice will be as it was before you edited it. NOTES ■ The VL1 has a Memory Voice Recall function that can be used to recall the last version of a voice if you accidentally make unwanted changes or lose your edited data as described above — Feature Reference manual, page 172. Controller Envelopes Since acoustic instruments virtually never respond instantaneously to “controller” changes, the VL1 includes a range of controller envelopes that can be used to simulate this type of response. For example, sudden application of maximum breath pressure to a wind instrument or bow speed to a string instrument normally doesn’t produce instantaneous sound. The instrument requires a few milliseconds to reach the full resonance demanded by the breath pressure or bowing. The VL1 provides programmable envelopes for the “Pressure”, “Embouchure/Pitch”, “Vibrato”, “Growl”, and “Amplitude/Filter” parameters, and these are described in detail on pages 128 through 150 of the Feature Reference manual. 46  Getting Started ● The Controllers Other Controller Views If you press the ∞ controller view: function button from the play mode you’ll see the following Polyphony This line shows which controller is currently assigned to polyphony mono/poly control. (≥ Feature Reference manual, page 36) Sustain Indicates whether sustain control is on or off. (≥ Feature Reference manual, page 35) Pitch Bend The VL1 has three different pitch bend modes — Normal, Bottom, and Top. The Bottom and Top modes are only effective when the Poly or Unison polyphony mode is selected. When Bottom is selected the lowest of two notes played will be affected by the pitch wheel, and when Top is selected the high note will be affected. When the Normal mode is selected both notes are affected. (≥ Feature Reference manual, page 35) Portamento The VL1 offers a choice of portamento modes with or without MIDI control capability. This line indicates the current portamento status. (≥ Feature Reference manual, page 40) Effect Any physical controller can be assigned to control certain of the VL1’s effects in certain ways: the wet/dry balance of the pitch change effect, the feedback delay send level, or the reverb send level. This line indicates which effect parameter is assigned for control by which controller. (≥ Feature Reference manual, page 45) The § function button calls the Continuous Slider (“CS”) controller view, which will look something like this: The continuous sliders can not be assigned to the instrument controller parameters listed above, but can be independently assigned to several other parameters that you can control in real time while playing. The parameters available for editing via the continuous sliders are individually preset for each voice. You can select from the available range by using the “Continuous Slider” assignment function described on page 43 of the Feature Reference manual. The continuous slider view shows you which parameters are assigned to which controller as well as the current positions of the controllers and their corresponding values. 47 The Controllers The controller parameters listed in this screen are not in the same category as those discussed in the preceding section, and therefore need to be introduced separately. All of the related parameters will be discussed in detail in the Feature Reference manual (pages listed below).  Getting Started ● Mixing & The Modifiers Mixing & The Modifiers Creating New Timbres and Original Voices The VL1 provides two ways to change the timbre of a voice to create original variations: 1) by mixing the output signals from various parts of the physical model, and 2) by using the VL1’s “Modifiers” to shape the overall harmonic structure. You should always start with the mixing parameters when attempting to create a new voice, so we’ll describe mixing first. Mixing The VL1’s physical instrument model produces three output signals that can be mixed to produce a surprising range of timbral variation. ● Driver The “Driver” signal is the direct output from the mouthpiece (or bow/string interface) without the resonance of the instrument’s body. In acoustic instruments there is always a certain amount of driver sound — particularly when the instrument is heard at close range. Judicious adjustment of the amount of driver signal added to the sound can significantly enhance the simulation. ● Pipe/String This is the main output from the instrument’s pipe or string. Tap Driver Pipe/String Mix Out (to modifiers) 48 ● Tap By “tapping” the output from a specific point along the instrument’s pipe or string and mixing that signal with the Driver and Pipe/ String signals, a range of variations can be produced. The Tap signal alone sounds almost the same as the Pipe/String signal, but since it has a different phase the tone can change drastically when the two signals are mixed due to phase cancellation and reinforcement.  Getting Started ● Mixing & The Modifiers An Exercise: Remix the Pan Pipes Voice Before going to the EDIT mode, select and play the Pan Pipes voice for a few minutes to get a feel for how it sounds. 1. Engage the EDIT Mode The mixing parameters are accessed via the EDIT mode “Mixing” page. To get to this page first press the E button to engage the edit mode. You may have to press the ] button one or more times to get the initial edit display. Select the Element 1 Miscellaneous Parameters Press the ™ function button to select the element-1 parameters, then press the ™ function button again (below “Misc” on the display) to call the “Miscellaneous” page. 3. Select & Edit the Mixing Parameters Move the cursor to “4:Mixing” and press [. Here you have all the parameters you need to mix the physical model output signals: Driver Output, Pipe/String Output, and Tap Output. These three parameters can be set from “0” (no output) to “127” (maximum output). Try changing their values to see how the sound is affected. Note that in the example display there are more Tap parameters. There is actually one more: move the cursor to the “Tap Setting” parameter and press the = button (or use the data dial) to set it to “Variable” (the previous setting, “Driving Point”, fixes the position of the tap output at the instrument’s driving point). Now the location of the tap can be set at any point via the “Tap Location” parameter. Try changing the “Tap Location” setting and notice how the tone changes. 49 Mixing & The Modifiers 2.  Getting Started ● Mixing & The Modifiers Tap Location 0% 50% 99% The remaining tap parameter — “Tap Sign” — inverts the phase of the tap signal. It has two settings: “+” and “-”. Try it. 4. Return To the PLAY Mode When Done Press the P button to return to the PLAY mode when you’ve finished experimenting with the mixing parameters. After experimenting with the Mixing parameters for a while you’ll discover that they define the basic sound of the instrument. Once you’ve created the basic sound you want by using the Mixing parameters, then you can move on the Modifiers to refine the sound. 50  Getting Started ● Mixing & The Modifiers The Modifiers In (from physical model) Harmonic Enhancer Dynamic Filter Frequency Equalizer Impulse Expander Resonator Out (to effects stage) Harmonic Enhancer Of the five modifier stages, the Harmonic Enhancer has the most pronounced effect on the actual harmonic structure of the sound. It allows you to create radical timbral variations within the current instrument “family”. Modulator Source. Modulator Carrier Source. Carrier Driver, pipe/string, and tap sound. Wet/Dry Balance 51 Out (to Dynamic Filter.) Mixing & The Modifiers As described in the “VL1 Basics” section (page 8), the VL1 has five “Modifier” stages that shape the overal timbre of the sound. Although the modifiers can vary the sound over a considerable range, the fundamental timbre of each voice is determined by its physical instrument model. If you start with a trumpet voice, for example, the modifiers will let you create an broad range of timbres, but the final sound will always be more or less trumpet-like. It is therefore important to choose a voice that provides the right foundation for the sound you are trying to achieve when attempting to create an original sound. The five modifier stages are:  Getting Started ● Mixing & The Modifiers Referring to the block diagram of the harmonic enhancer, above, we can see that it employs a modulation approach to building new harmonic structures. The carrier and modulator blocks have independent display pages and some independent parameters. ■ The Modulator Parameter Page ■ The Carrier Parameter Page NOTES ■ If you want to experiment with the Harmonic Enhancer parameters while reading this section, they can be accessed by selecting the EDIT mode and, from the initial EDIT mode display (try pressing ] if the initial EDIT display doesn't appear), pressing ™ (“E1”) to select the Element 1 parameters, then pressing £ (“Modi”) to select the Modifier parameters, and finally moving the cursor to “1:Harmonic Enhancer” and pressing [. Once the Harmonic Enhancer display is selected the carrier and modulator pages are selected via ¡ (“Crr”) and ™ (“Mod”), respectively. The “Signal Select” parameters in these pages allow independent selection of the six different signal sources listed below. Normal This is the total output of the instrument model: a mix of the driver, pipe/string, and tap signals. Breath Noise Amplitude This signal represents the instantaneous amplitude of the breath noise produced at the driver. It is basically a highly distortion version of the Slit/Friction signal described below. Flow Rate Saturation When the pressures on either side of an aperture (e.g. a mouthpiece/ reed assembly) differ, a corresponding flow of air is produced. There is, however, a limit to the speed of the airflow which can be produced (saturation). The relationship between the pressure difference and resulting airflow is derived as the Flow Rate Saturation signal. Beat The beat signal represents contact between the vibrating reed and the mouthpiece. Slit/Friction As the reed vibrates, the area of gap (slit) between it and the mouthpiece varies accordingly. The Slit/Friction signal corresponds to the varying area of the reed/mouthpiece slit. Reed This signal is derived directly from the flexing of the reed. 52  Getting Started ● Mixing & The Modifiers While the “Balance” and “Index” parameters apply to the overall harmonic enhancer sound, the following independent parameters are provided for the modulator and carrier blocks. HPF Cutoff Both the modulator and carrier blocks have high-pass filters that can be used to roll off the low frequencies of the corresponding signal. The cutoff frequency can be varied from 17.0 Hz to 11.2 kHz. Overdrive This parameter boosts the corresponding modulator or carrier signal, forcing it into distortion and thereby drastically changing its harmonic structure. Phase This parameter is provided for the modulator block only. It allows a degree of timbral variation by varying the phase of the modulator signal through 360 degrees in 2- or 3-degree increments. Look at the Harmonic Enhancer display pages again. Parameters with an inverse “K”(˚) next to them can also be controlled by key scaling — i.e. the value of the parameter changes according to the pitch of the key played. This makes it possible to achieve both natural and unprecedented timbral variations across the range of the keyboard. NOTES ■ Refer to page 107 of the Feature Reference manual for full details on the Harmonic Enhancer parameters. 53 Mixing & The Modifiers Although any modulator source signal can be applied to any carrier source signal, two approaches are recommended when attempting to create an acoustic instrument simulation. The first is to set the carrier signal to “Normal” and the modulator signal to any other than normal, set the dry/wet “Balance” to 63 (all wet), and set a relatively high modulator “Index” value. In this case the total output of the instrument model (“Normal” signal) will by modulated by one of the component signals, so the dry/wet “Balance” can be set to fully wet (modulated carrier output only) since the carrier source and dry signals are essentially the same. The “Index” parameter determines how much modulation is applied, so a higher value is generally required to create sufficient variation. The second approach is to set the carrier signal to any other than normal and the modulator signal to any of the six possibilities, set the dry/wet “Balance” to a more central value, and set a relatively low modulator “Index” value. In this situation it is necessary to set the “Balance” more toward the “Dry” side since the carrier source signal is not the normal signal and at least some of the dry signal is necessary to provide the basic sound of the instrument model. In other words, the sound produced by the Harmonic Enhancer is simply added to the basic sound of the instrument, in contrast with the first approach in which the basic sound of the instrument is modulated directly. Please note that these are only guidelines, and are by no means the only way to work with the Harmonic Enhancer. Since the Harmonic Enhancer tends to respond differently with different instrument models, experimentation and experience are your most valuable tools.  Getting Started ● Mixing & The Modifiers Dynamic Filter The Dynamic Filter stage is similar to the dynamic filters found in many conventional synthesizers. It allows both fixed and dynamic filtering in high-pass, low-pass, bandpass, and band elimination modes, and is effective for broad tonal control. Dynamic Filter In (from Harmonic Enhancer) Wet/Dry Balance Out (to Frequency Equalizer) ■ The Dynamic Filter Parameter Page The dry/wet “Balance” parameter allows delicate variations in the degree of filtration applied. The “Cutoff Tracking” parameter selects either the “Fixed” mode in which the cutoff frequency of the filter is fixed at the specified cutoff frequency in Hz (“Cutoff Freq.” parameter), or the “KeyTrack” mode in which the cutoff frequency varies according to the key played. When “KeyTrack” is selected the cutoff frequency is specified in octaves. Another important feature is “Resonance” — a parameter that produces a variable resonant peak at the specified cutoff frequency in any of the filter’s modes. NOTES ■ Refer to page 115 of the Feature Reference manual for full details on the Dynamic Filter parameters. 54  Getting Started ● Mixing & The Modifiers Frequency Equalizer The Frequency Equalizer stage consists of two blocks — Auxiliary and Band — each with its own display page. Equalizer (Auxiliary) Equalizer (Bands) Out (to Impulse Expander) ■ The Equalizer Auxiliary Parameter Page ■ The Equalizer Band Parameter Page The Auxiliary block includes programmable low-pass and high-pass filters that can be used independently or together to create a bandpass response. Both the low-pass and high-pass filters have independent key-scaling parameters that can be used to vary the gain of the filters across the range of the keyboard. The “Input Gain” parameter adjusts the level of the signal applied to the input of the Equalizer Auxiliary stage. The Equalizer Band block is a 5-band parametric equalizer with frequency, Q (bandwidth), and level control. The Band block functions in the same way as any standard parametric equalizer, allowing flexible response control over a wide range. NOTES ■ Refer to page 122 of the Feature Reference manual for full details on the Frequency Equalizer parameters. 55 Mixing & The Modifiers In (from Dynamic Filter)  Getting Started ● Mixing & The Modifiers Impulse Expander The Impulse Expander works in conjunction with the Resonator, described below, to simulate the effect of an instrument’s resonant cavity or sound box. It can also be used to simulate the acoustic environment in which the instrument is played. In (from Frequency Equalizer) Frequency-dependent Delay Mix Out (to Resonator) ■ The Impulse Expander Parameter Page In contrast to the Resonator, the Impulse Expander is more suited to the simulation of metallic resonances and is thus invaluable for refining the sound of brass and metalbodied woodwinds. Other important effects are the ability to diffuse sharp attack sounds and to give depth and realism to vibrato. In fact, the Impulse Expander should only be used with voices which have a degree of vibrato or other cyclic variation, since its effect is less noticeable on uniformly sustained sounds. Since the Impulse Expander is not essential for all voices, it can be turned completely off when not needed. It also has “Wet Level”, “Dry Level”, and stereo “Level Balance” parameters that allow its effect to be blended into the main sound as required. NOTES ■ Refer to page 125 of the Feature Reference manual for full details on the Impulse Expander parameters. 56  Getting Started ● Mixing & The Modifiers Resonator While the Impulse Expander tends to give the sound a metallic quality, the Resonator produces a more woody resonance effect. Careful adjustment of the resonator’s parameters can often bring a not-quite-right voice to life. Delay Delay In (from Impulse Expander) Delay Right Channel Out (to Effects) Left Channel Delay ■ The Resonator Parameter Page The Resonator basically consists of five parallel delay lines with independently programmable delay times (DL1 through DL5, variable from 0.25 to 41.45 milliseconds). Other parameters include variable “Decay Time”, “LPF Cutoff Freq.” (low-pass filtercutoff frequency), “Diffusion”, and “Phase”. Like the Impulse Expander, the Resonator is not essential for all voices and can be turned completely off when not needed. It also has “Input Gain”, “Wet Level”, and stereo “Level Balance” parameters that allow its effect to be blended into the main sound as required (the cursor is moved around the block diagram in the “IE & RSN SETTING” page, shown below, to select the parameters associated with the various blocks). ■ The Impulse Expander & Resonator Setting Page (IE = Impulse Expander, RSN = Resonator) NOTES ■ Refer to page 126 of the Feature Reference manual for full details on the Resonator parameters. 57 Mixing & The Modifiers Delay  Getting Started ● Effects Effects Creating the Right Ambience Effects are the essential finishing touches for any voice. Once you’ve created a sound you like, use one or more of the VL1’s three high-performance digital effect stages to polish and refine it as required. Each stage includes a number of effects. The Modulation, Feedback Delay, and Reverb stages can be used simultaneously, but only one of the effects available in each stage can be used at a time. L R Modulation Feedback Delay L Reverb R All effects can be accessed from the initial EDIT mode display by press the ¡ button (“Com”) to select the common voice parameters, and then the ™ button (“Efct”) to call the effect directory. Then move the cursor to the name of the desire effect stage and press [ button. 58  Getting Started ● Effects Modulation Effects Although “modulation” usually implies some sort of cyclical variation, the VL1 Modulation stage allows selection of Flanger, Pitch Change, and Distortion effects (only Flanger fits the traditional definition of a modulation effect). Since most of these effects produce a marked change in the sound, you’ll probably only want to use them on certain voices, and maybe not all the time. This type of effect is created by slightly delaying the sound and periodically varying the delay time. The delayed signal is then added to the direct signal causing a variable comb-filter effect which results in the familiar “swishing” flanger sound. Pitch Change A dual pitch change effect which can be used in the Mono mode, in which both pitch-shifted notes appear on both channels, or the Stereo mode in which one pitch-shifted note appears on the left channel and the other on the right. The pitch of the two pitch-shifted notes can be set over a two-octave range — from one octave below to one octave above the input note. Distortion An extremely versatile distortion effect which offers transistor, vintage tube, fuzz and other distortion types, a variety of speaker types, and a comprehensive range of other parameters that can be used to refine the distortion sound. NOTES ■ Refer to page 46 of the Feature Reference manual for full details on the Modulation effects and parameters. Feedback Delay Effects All three effects available in the Feedback Delay stage are basically designed to produce distinct repeat delays or echoes. You have extensive control over the number of repeats produced and the way they decay. Mono The Mono delay effect produces a single delay sound which appears in the center of the stereo sound field. L, R This variation provides independently programmable delays for the left and right stereo channels. L, C, R Independent delays are provided for the left and right channels, plus a center delay. Since the goal in producing a delay effect is often to match the delay time to a musical time value, the VL1 includes a “time calculation” function that makes it easy to convert standard note values to their corresponding delay times in milliseconds. 59 Effects Flanger  Getting Started ● Effects ■ The Time Calculation Pop-up Page NOTES ■ Refer to page 53 of the Feature Reference manual for full details on the Feedback Delay effects and parameters. Reverb Effects You’ll probably want to apply the effects in this stage to some degree to all your voices. These are the effects that will give your sound ambience and a sense of dimension, adding warmth and depth to an otherwise dry sound. Hall 1 A simulation of the reverbation characteristics of a fairly standard concert hall. Hall 2 This hall simulation produces a richer low-frequency reverb sound than the Hall 1 program. Room 1 The ambience of a small room rather than a large hall. This effect is ideal when you just want a subtle touch of ambience. Room 2 A larger room than the Room 1 simulation, with a correspondingly “bigger” reverb sound. Studio In recording studios it is generally desirable to suppress low-frequency reverberation without entirely losing the “live” sound of the room. The Studio program simulates this type of environment. Plate The plate reverb unit is a classic tool of the recording trade — it was the first mechanical method of creating artificial reverberation that was capable of producing satisfactory results in the studio. This is a very realistic simulation. Space A diffuse reverberation of the type you might experience in an extremely large space. Reverse In this effect the reverb sound plays in reverse, building up to maximum level rather than decaying as normal. For even more versatility all of the reverb effects have a “Feel” parameter with four settings which produce significant changes in the basic sound of the effect. In essence you have 32 distinct reverb programs (8 effects x 4 Feel settings). Another innovative feature of the reverb effects is a Reverb Time Boost parameter which can be used to extend the tail end of the reverb sound in fine increments. NOTES ■ Refer to page 60 of the Feature Reference manual for full details on the Reverb effects and parameters. 60  Getting Started ● Effects Effects 61  Getting Started ● Index Index This index covers both the VL1 Getting Started and Feature Reference manuals for easy cross-referencing. Page numbers in the Getting Started manual are preceded by “©”, and page numbers in the Feature Reference manual are preceded by “ƒ”. Conventions Copy button Copy function Crossfade speed Cursor buttons A Absorption Aftertouch curve Amplitude & filter envelope Amplitude & filter key scaling Amplitude Assign mode ƒ81 ƒ157 ƒ143 ƒ146-150 ƒ71 ƒ35 D Damping Data dial Decrement & increment buttons Demo playback Device number Disk format Disk status Disk, delete file Disk, load from Disk, rename file Disk, save to Display mode Distortion Dynamic filter Dynamic filter key scaling B Backup battery Bank buttons Breath attack gain Breath attack time Breath control curve Breath controller calibration Breath controller Breath controller jack Breath noise Breath noise key scaling Bulk dump, MIDI ©7 ©17 ƒ25 ƒ85 ©18 ©4 ©19, 34. ƒ15 ƒ36 ƒ36 ƒ157 ©29 ©23 ©19 ƒ73, 86 ƒ88-90 ƒ161 ƒ80 ©18, 35. ƒ16 ©18, 35. ƒ16 ©26. ƒ175 ƒ155 ƒ171 ƒ163 ƒ170 ƒ164 ƒ168 ƒ166 ƒ158 ƒ51 ©54. ƒ77, 115 ƒ117-118 C Common miscellaneous Confirm mode Continuous slider assignment Continuous sliders Controller envelopes Controller search & replace Controller parameters Controller views Controllers E ƒ34 ƒ158 ƒ43 ©18, 47. ƒ19 ©46 ƒ82 ©40 ©41, 47. ƒ17 ©12, 38 Edit compare function Edit recall Effect control Effect on/off Effects Element detune Element level Element names Element note shift 62 ƒ24 ƒ173 ƒ45 ƒ23 ©58 ƒ37 ƒ38 ƒ31 ƒ37  Getting Started I Impulse expander & resonator setting Impulse expander Initial edit page Interpolate speed Key mode Keyboard Keyboard transpose ƒ31 ©19 ƒ153 L L,C,R delay L,R delay LCD display Local on/off ©59 ƒ53 ƒ45 ƒ47 ©19 ©5 ƒ156 ©20 ©23 ©23 ƒ156 ©20 ©18 ƒ9 ƒ57 ƒ55 ©18 ƒ155 M Manuals, about the Master tuning Memory protect Micro tuning MIDI connections MIDI connectors MIDI settings Mixing Mixing key scaling Mode buttons Modes, the 3 main Modifier on/off Modifiers Modulation effect type Modulation effects Modulation wheel 2 assign Modulation wheels Mono delay G Greeting message Growl envelope Growl Growl speed key scaling ƒ123 ©56. ƒ125 ƒ30 ƒ85 K F Feedback delay effects Feedback delay Feedback delay/reverb mode Flanger Floppy disk drive Floppy disks & drive, handling Foot controller 2 assign Foot controller jacks Foot controllers Foot switches Foot switch assign Foot switch jacks Function buttons Functions & parameters, finding Index ƒ158 ƒ141 ƒ74 ƒ142 ©6. ƒ4 ƒ154 ƒ158 ƒ42 ©24 ©20 ƒ155 ©48. ƒ98 ƒ100-105 ©17 ƒ8 ƒ23 ©51 ƒ46 ©59 ƒ156 ©19 ƒ53 H Harmonic enhancer Harmonic enhancer key scaling Headphones ©51. ƒ78, 107 ƒ110-115 ©23 N Navigation aids ƒ11 O Octave buttons Octave switch hold Output jacks 63 ©19 ƒ153 ©20 Index Element on/off ƒ22 ƒ38 Element pan ƒ37 Element random pitch ƒ22 Element select ƒ130 Embouchure & pitch envelope Embouchure & pitch envelope key scaling ƒ132-134 Embouchure ƒ66 ©18 Enter button ƒ119 Equalizer auxiliary ƒ122 Equalizer band ©55 Equalizer ƒ120-121 Equalizer key scaling Error messages ƒ180 ©18 Exit button ●  Getting Getting Started Started ●● Effects Index P Phones jack Pitch bend mode Pitch change Pitch Pitch wheel Play-mode display Polyphony control Portamento Power cord socket Power supply Power switch Power-on procedure Pre-programmed voices, loading Pressure envelope Pressure V ©19 ƒ35 ƒ49 ƒ67 ©19 ©34. ƒ14 ƒ36 ƒ40 ©20 ©22 ©20 ©25 ©31 ƒ129 ƒ65 Velocity curve Vibrato envelope Vibrato envelope key scaling Vibrato Voice directory Voice list, abbreviated Voice mode Voice name Voice number buttons Voice selection Volume control Q Quick editing ƒ19 R Receive channel Resonator Reverb effects Reverb ƒ155 ©57. ƒ126 ©60 ƒ60 S Scream Selecting & editing parameters Sound system Specifications Store button Store function Sustain ƒ72 ƒ12 ©24 ƒ184 ©17 ƒ28 ƒ35 T Throat formant Throat formant key scaling Time calculation, musical Tonguing Touch EG time Transmit channel Trigger mode Troubleshooting ƒ75, 91 ƒ93-97 ƒ59 ƒ70 ƒ36 ƒ155 ƒ85 ƒ178 64 ƒ157 ƒ135 ƒ137-140 ƒ69 ©36 ©37 ƒ32 ƒ31 ©19, 34. ƒ15, 22 ©34. ƒ15 ©18  M.D.G., EMI Division © Yamaha Corporation 1993 VQ65370 JADIR0PR117.2CP Printed in Japan