Documenttranscriptie

U C AT HTR-5140 HTR-5140 Natural Sound AV Receiver Ampli-Tuner Audio-Video OWNER’S MANUAL MODE D’EMPLOI YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA 05HTR-5140-e/f cv1/4 1 Printed in Malaysia ID V343260 6/22/99, 2:41 PM  SAFETY INSTRUCTIONS 8 Ventilation – The unit should be situated so that its location or position does not interfere with its proper ventilation. For example, the unit should not be situated on a bed, sofa, rug, or similar surface, that may block the ventilation openings; or placed in a built-in installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings. 9 Heat – The unit should be situated away from heat sources such as radiators, stoves, or other appliances that produce heat. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. • Explanation of Graphical Symbols The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. 1 Read Instructions – All the safety and operating instructions should be read before the unit is operated. 2 Retain Instructions – The safety and operating instructions should be retained for future reference. 3 Heed Warnings – All warnings on the unit and in the operating instructions should be adhered to. 4 Follow Instructions – All operating and other instructions should be followed. 5 Water and Moisture – The unit should not be used near water – for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc. 6 Carts and Stands – The unit should be used only with a cart or stand that is recommended by the manufacturer. 6A A unit and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the unit and cart combination to overturn. 7 10 Power Sources – The unit should be connected to a power supply only of the type described in the operating instructions or as marked on the unit. 11 Power-Cord Protection – Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the unit. 12 Cleaning – The unit should be cleaned only as recommended by the manufacturer. 13 Nonuse Periods – The power cord of the unit should be unplugged from the outlet when left unused for a long period of time. 14 Object and Liquid Entry – Care should be taken so that objects do not fall into and liquids are not spilled into the inside of the unit. 15 Damage Requiring Service – The unit should be serviced by qualified service personnel when: A. The power-supply cord or the plug has been damaged; or B. Objects have fallen, or liquid has been spilled into the unit; or C. The unit has been exposed to rain; or D. The unit does not appear to operate normally or exhibits a marked change in performance; or E. The unit has been dropped, or the cabinet damaged. 16 Servicing – The user should not attempt to service the unit beyond those means described in the operating instructions. All other servicing should be referred to qualified service personnel. 17 Power Lines – An outdoor antenna should be located away from power lines. 18 Grounding or Polarization – Precautions should be taken so that the grounding or polarization is not defeated. Wall or Ceiling Mounting – The unit should be mounted to a wall or ceiling only as recommended by the manufacturer. 2 05HTR-5140-e/f-1 2 6/22/99, 2:04 PM  Note to CATV system installer: This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. English 19 For US customers only: Outdoor Antenna Grounding – If an outside antenna is connected to this unit, be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. EXAMPLE OF ANTENNA GROUNDING MAST ANTENNA LEAD IN WIRE GROUND CLAMP ANTENNA DISCHARGE UNIT (NEC SECTION 810–20) ELECTRIC SERVICE EQUIPMENT GROUNDING CONDUCTORS (NEC SECTION 810–21) GROUND CLAMPS POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250. PART H) NEC – NATIONAL ELECTRICAL CODE FCC INFORMATION (for US customers only) 1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT : When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA. 3. NOTE : This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference. Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to coaxial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA 90620. The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries. We Want You Listening For A Lifetime YAMAHA and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or distortion – and, most importantly, without affecting your sensitive hearing. Since hearing damage from loud sounds is often undetectable until it is too late, YAMAHA and the Electronic Industries Association’s Consumer Electronics Group recommend you to avoid prolonged exposure from excessive volume levels. 3 05HTR-5140-e/f-1 3 6/22/99, 2:04 PM  SUPPLIED ACCESSORIES ACCESSOIRES FOURNIS • After unpacking, check that the following parts are included. • Après le déballage, vérifier que les pièces suivantes sont incluses. • Remote control transmitter • Télécommande • Indoor FM Antenna • Antenne FM intérieure • AM Loop Antenna • Cadre-antenne AM • Antenna adapter (U.S.A. and Canada models only) • Adaptateur d’antenne (Modèles pour les Etats-Unis et le Canada seulement) • Batteries (size AAA, R6, UM-4) • Piles (taille AAA, R6, UM-4) 4 05HTR-5140-e/f-1 4 6/22/99, 2:04 PM  ● 5-Channel Power Amplification Minimum RMS Output Power <0.04% THD, 20 Hz – 20 kHz> ● 6-Channel External Decoder Input for DTS and other future formats ● Automatic Input Balance Control for Dolby Pro Logic Surround Main: 60 W + 60 W (8 Ω) Center: 60 W (8 Ω) Rear: 60 W + 60 W (8 Ω) ● Test Tone Generator for Easier Speaker Balance Adjustment <0.07% THD, 1 kHz> ● Speaker Output Mode Changing Capability Main: 70 W + 70 W (8 Ω) Center: 70 W (8 Ω) Rear: 70 W + 70 W (8 Ω) ● 40-Station Random Access Preset Tuning ● Digital Sound Field Processor ● Automatic Preset Tuning ● Dolby Digital Decoder ● Preset Station Shifting Capability (Preset Editing) ● Dolby Pro Logic Surround Decoder ● CINEMA DSP: Theater-like Sound Experience by the Combination of Dolby Surround and YAMAHA DSP Technology ● Video Signal Input/Output Capability ● SLEEP Timer ● Universal Remote Control Transmitter with Preset Manufacturer Codes CONTENTS SUPPLIED ACCESSORIES ........................................... 4 FEATURES .................................................................... 5 CAUTION ....................................................................... 6 ● Information about DSP ● Introduction ● Advanced Information FEATURES OF SOUND EFFECTS ............................... 7 CONTROLS AND THEIR FUNCTIONS ......................... 9 ADJUSTMENTS IN THE “SET MENU” MODE ................................... 44 ● Preparation ● Remote Control Transmitter SPEAKER SETUP ....................................................... 14 CONNECTIONS ........................................................... 16 ADJUSTMENTS BEFORE USING THIS UNIT .................................. 23 REMOTE CONTROL TRANSMITTER ......................... 46 SETUP CODES ........................................................... 53 ● Basic Operation BASIC OPERATIONS .................................................. 28 TUNING OPERATIONS ............................................... 32 SETTING THE SLEEP TIMER ..................................... 37 USING THE DIGITAL SOUND FIELD PROCESSOR (DSP) .............................................. 38 TROUBLESHOOTING ................................................. 54 SPECIFICATIONS ....................................................... 57 LIST OF MANUFACTURER’S CODES ...................... 113 5 05HTR-5140-e/f-1 5 6/22/99, 2:04 PM English FEATURES  CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. 1. To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. 2. Install this unit in a cool, dry, clean place – away from windows, heat sources, sources of excessive vibration, dust, moisture and cold. Avoid sources of humming (transformers, motors). To prevent fire or electrical shock, do not expose the unit to rain or water. 3. Never open the cabinet. If something drops into the set, contact your dealer. 4. Do not use force on switches, controls or connection wires. When moving the unit, first disconnect the power plug and the wires connected to other equipment. Never pull the wires themselves. 5. The openings on the unit cover assure proper ventilation of the unit. If these openings are obstructed, the temperature inside the unit will rise rapidly. Therefore, avoid placing objects against these openings, and install the unit in a well-ventilated area to prevent fire and damage. <Singapore model only> Be sure to allow a space of at least 20 cm behind, 20 cm on the both sides and 30 cm above the top panel of the unit to prevent fire and damage. 6. The voltage used must be the same as that specified on this unit. Using this unit with a higher voltage than specified is dangerous and may result in fire or other accidents. YAMAHA will not be held responsible for any damage resulting from use of this unit with a voltage other than specified. 7. Digital signals generated by this unit may interfere with other equipment such as tuners, receivers or TVs. Move this unit farther away from such equipment if interference is observed. 8. Always set the VOLUME control to “ ” before starting the audio source play. Increase the volume gradually to an appropriate level after playback has been started. 9. Do not attempt to clean the unit with chemical solvents; this might damage the finish. Use a clean, dry cloth. 10. Be sure to read the “TROUBLESHOOTING” section regarding common operating errors before concluding that the unit is faulty. This unit is not disconnected from the AC power source as long as it is connected to the wall outlet, even if this unit itself is turned off. This state is called the standby mode. In this state, this unit is designed to consume a very small quantity of power. FREQUENCY STEP switch (China and General Models only) Because the interstation frequency spacing differs in different areas, set the FREQUENCY STEP switch (located at the rear) according to the frequency spacing in your area. Before setting this switch, disconnect the AC power plug of this unit from the AC outlet. IMPORTANT Please record the serial number of this unit in the space below. MODEL: Serial No.: The serial number is located on the rear of the unit. Retain this Owner’s Manual in a safe place for future reference. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. FOR CANADIAN CUSTOMERS To prevent electric shock, match wide blade of plug to wide slot and fully insert. This Class B digital apparatus complies with Canadian ICES-003. 11. When not planning to use this unit for long periods of time (ie., vacation, etc.), disconnect the AC power plug from the wall outlet. 12. To prevent lightning damage, disconnect the AC power plug and disconnect the antenna cable when there is an electrical storm. 13. Grounding or polarization – Precautions should be taken so that the grounding or polarization of an appliance is not defeated. 14. AC outlet Do not connect audio equipment to the AC outlet on the rear panel if that equipment requires more power than the outlet is rated to provide. 15. Voltage Selector (China and General Models only) The voltage selector on the rear panel of this unit must be set for your local main voltage BEFORE plugging into the AC main supply. Voltages are 110/120/220/240 V AC, 50/60 Hz. 6 05HTR-5140-e/f-1 6 6/22/99, 2:04 PM  English FEATURES OF SOUND EFFECTS Introduction Welcome to the exciting world of digital home entertainment. This unit is one of the most complete and advanced AV receivers available. Some of the more advanced features may not be familiar to you, but they are easy to use. State-of-the-art technologies such as Dolby Digital and Digital Theater Systems (DTS) may be new to your home, but you have probably experienced the amazing realism they bring to feature films in theaters around the world. To make the listening experience even more enjoyable, this unit includes a number of exclusive, digitally created listening environments known as digital sound fields. Choosing a sound field program is like transporting yourself to such venues as an outdoor arena, a European church, or a cozy jazz club. Take some time now to read more about these features and enjoy the new experiences this unit brings to your home theater. Digital Sound Field Processing What is it that makes live music so good? Today’s advanced sound reproduction technology lets you get extremely close to the sound of a live performance, but the chances are that you’ll still notice something missing — the acoustic environment of the live concert hall. Extensive research into the exact nature of the sonic reflections that create the ambience of a large hall has made it possible for YAMAHA engineers to bring you this same sound to your listening room, so you’ll feel all the sound of a live concert. Furthermore, our technicians, armed with sophisticated measuring equipment, have even made it possible to capture the acoustics of a variety of actual concert halls, theaters, etc. from around the world, to allow you to accurately re-create any one of these live performance environments, all in your own home. Dolby Pro Logic Surround Dolby Pro Logic Surround has been used in movie theaters since the mid-seventies. It has also been available in home entertainment systems since the late eighties and continues to be a popular format for home theater systems. It uses four discrete channels and five speakers to reproduce realistic and dynamic sound effects: two main channels (left and right), a center channel for dialog, and a rear channel for special sound effects. The rear channel reproduces sound within a narrow frequency range. Most video tapes and laser discs include Dolby Pro Logic Surround encoding, as do many TV and cable broadcasts. The Dolby Pro Logic Surround decoder built into this unit employs a digital signal processing system that stabilizes each channel for even more accurate sound positioning than is available with standard analog processors. Dolby Digital The built-in Dolby Digital decoder leads you into a totally new sound experience. Dolby Digital is a new generation of multi-channel digital audio technology, or the newest spatial sound processing format developed for 35 mm-film movies by employing a new kind of low bit-rate audio coding. Dolby Digital is a digital surround sound system that provides completely independent multi-channel audio to listeners. In multi-channel form, Dolby Digital provides 5 full-range channels in what is sometimes referred to as a “3/2” configuration: three front channels (left, center and right), plus two surround channels. A sixth bass-only effect channel is also provided for output of LFE (low frequency effect), or low bass effects that are independent of other channels. This channel is counted as 0.1, thus giving rise to the term 5.1 channels in total. Compared to Dolby Pro Logic, which is referred to a “3/1” system (left front, center, right front and just one surround channel), Dolby Digital features two surround channels, called stereo or split surrounds, each offering the same full-range fidelity as the three front channels. Sound of wide dynamic range reproduced by the 5 full-range channels provides listeners with excitement that has never been experienced before. Precise sound orientation by discrete digital sound processing expands the realism that the original movie possesses. LD and DVD are home audio/video program source that could benefit from Dolby Digital. In the near future, Dolby Digital will also be applied to DBS, CATV and HDTV. The ongoing release of Dolby Stereo Digital theatrical films now underway will provide an immediate source of Dolby Digital encoded video software. 7 05HTR-5140-e/f-1 7 6/22/99, 2:04 PM  The following original functions make the surround-sound effect of Dolby Digital become the most suitable for your audio system and the listening conditions. Manufactured under license from Dolby Laboratories Licensing Corporation. “DOLBY”, “PRO LOGIC”, and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation. Copyright 1992 Dolby Laboratories, Inc. All rights reserved. CINEMA DSP: Dolby Surround + DSP The Dolby Surround sound system shows its full ability in a large movie theater, because movie sounds are originally designed to be reproduced in a large movie theater using many speakers. It is difficult to create a sound environment similar to that of a movie theater in your listening room, because the room size, materials of inside walls, the number of speakers, etc. of your listening room are very different from those of a movie theater. YAMAHA DSP technology made it possible to present you with nearly the same sound experience as that of a large movie theater in your listening room by compensating for the lack of presence and dynamics in your listening room with its original digital sound fields combined with the Dolby Surround sound system. CINEMA DSP The YAMAHA “CINEMA DSP” logo indicates those programs that are created by the combination of Dolby Surround and YAMAHA DSP technology. Dolby Pro Logic + 2 Digital Sound Fields Dolby Digital + 3 Digital Sound Fields Digital sound fields are created on the presence side and the rear surround side of the Dolby Pro Logic Surround-decoded sound field, respectively. They create a wide acoustic environment and emphasize the surround effect in the room, letting you feel as much presence as if you are watching a movie in a popular Dolby Stereo theater. Digital sound fields are created on the presence side and the independent left and right surround sides of the Dolby Digitaldecoded sound field, respectively. They create a wide acoustic environment and strong surround effect in the room without losing high-channel separation. With the wide dynamic range of Dolby Digital sound, this sound field combination lets you feel as if you are watching a movie in the newest Dolby Stereo Digital theater. This will be the most ideal home theater sound at the present time. This combination is available when the DOLBY PRO LOGIC ENHANCED/DOLBY DIGITAL ENHANCED, 70 mm MOVIE THEATER/DIGITAL MOVIE THEATER or TV SPORTS sound field program is selected, and the input signal of source is analog, PCM audio or encoded with Dolby Digital sound in 2-channel. This combination is available when the DOLBY PRO LOGIC ENHANCED/DOLBY DIGITAL ENHANCED, 70 mm MOVIE THEATER/DIGITAL MOVIE THEATER or TV SPORTS sound field program is selected, and the input signal of source is encoded with Dolby Digital sound (except in 2-channel). 8 05HTR-5140-e/f-1 8 6/22/99, 2:04 PM  English CONTROLS AND THEIR FUNCTIONS FRONT PANEL 1 STANDBY/ON 6 TUNING MODE (AUTO/MAN’L MONO) Press this switch to turn on the power to this unit. Press it again to set this unit to the standby mode. Press this button to switch the tuning mode to automatic or manual. To select the automatic tuning mode, press this button so that the “AUTO TUNING” indicator lights up on the display. To select the manual tuning mode, press this button so that the “AUTO TUNING” indicator goes off. Standby mode In this state, this unit consumes a very small quantity of power to receive infrared-signals from the remote control transmitter. 2 Remote control sensor This receives signals from the remote control transmitter. 3 Display 7 FM/AM Press this button to switch the reception band to FM or AM. 8 TUNING UP/DOWN This button is used for tuning. Press the UP side to tune in to higher frequencies, and press the DOWN side to tune in to lower frequencies. This shows various information. (Refer to page 11 for details.) 9 TAPE/MD MON / EXT. DECODER 4 MEMORY (MAN’L/AUTO FM) Press this button to play a tape or an MD. The “TAPE/MD MON” indicator lights up on the display. When you press the button next, the “TAPE/MD MON” indicator goes off, “EXT. DECDR” appears on the display and you can play the signal connected to the EXTERNAL DECODER INPUT terminals. Press this button to store the broadcasting stations. When this button is pressed and held for more than three seconds, the automatic preset tuning begins. 5 EDIT This button is used to exchange the assignment of two preset stations with each other. 0 INPUT Turn this selector to select the program source (VCR, VIDEO AUX, TV/DBS, DVD/LD, CD, TUNER, PHONO) to listen to or watch. The name of the selected program source appears on the display. 9 05HTR-5140-e/f-1 9 6/22/99, 2:04 PM  q INPUT MODE i BALANCE This button switches the DVD/LD and TV/DBS input signal mode (AUTO/ANALOG). This control is used to raise or lower the volume level. This control is only effective for the sound from the main speakers. Turn the control to adjust the balance of the output volume to the left and right speakers to compensate for sound imbalance caused by the speaker location or listening room conditions. e PHONES jack o TIME/LEVEL When you use headphones, connect the headphones to the PHONES jack. You can listen to the sound to be output from the main speakers through the headphones. When using headphones only, set both SPEAKERS A and B to the OFF position and switch off the digital sound field processor (so that no DSP program name appears on the display) by pressing EFFECT. Press this button to select the item in the TIME/LEVEL mode. r SPEAKERS a SET MENU Set A or B (or both A and B) to the ON position for the main speaker system (connected to this unit) that you want to use. Set the button(s) for the main speaker system you don’t want to use to the OFF position. Press this button to select functions in the SET MENU mode. w VOLUME t A/B/C/D/E Press this button to select one of a group (A to E) of preset stations. y Preset station number selector Each of these buttons selects a preset station number (1 to 8). u Tone controls These controls are only effective for the sound from the main speakers. BASS Use this control to increase or decrease the low-frequency response. The “0” position produces flat response. TREBLE Use this control to increase or decrease the high-frequency response. The “0” position produces flat response. p +/– These buttons are used to adjust the settings of the SET MENU mode and the TIME/LEVEL mode. In the TIME/LEVEL mode, press + to increase the delay time or speaker output level. Press – to decrease the delay time or speaker output level. s PROGRAM selector Press or to select the DSP program. The name of the selected program appears on the display. d EFFECT This button switches on and off the output from the center and rear speakers so that the sound becomes the normal 2-channel. * Even if the output from the center and rear speakers is off, when the Dolby Digital is decoded, the signals on all channels are distributed to the main channels and output from the main speakers. f VIDEO AUX terminals Connect an auxiliary video or audio input source unit such as a camcorder to these terminals. The source connected to these terminals can be selected by INPUT. 10 05HTR-5140-e/f-1 10 6/22/99, 2:04 PM  English DISPLAY PANEL 1 Multi-information display 6 Signal-level meter This displays various information, for example the station frequency, preset station number and name of the selected program source. This indicates the signal level of the station being received. If multipath interference is detected, the indication decreases. 2 MEMORY indicator When MEMORY is pressed, this indicator flashes for about five seconds. During this period, the displayed station can be stored in the memory. 3 AUTO TUNING indicator This lights up when the unit is in the automatic tuning mode. 4 TAPE/MD MON indicator This lights up when the tape deck (or MD recorder, etc.) is selected as the program source by pressing TAPE/MD MON / EXT. DECODER on the front panel or TAPE/MD on the remote control transmitter. 7 , and indicators “ ” lights up when the built-in Dolby Digital decoder is on and the signal of the selected source encoded in Dolby Digital sound is not in 2-channel. “ ” lights up when the built-in digital sound field processor is on, and “ ” lights up when the built-in Dolby Pro Logic Surround decoder is on. Depending on the selected DSP program, both “ ” and “ ”, or both “ ” and “ ” will light up. 8 SLEEP indicator This lights up while the built-in SLEEP timer is functioning. 5 STEREO indicator This lights up when an FM stereo broadcast with sufficient signal strength is being received. 11 05HTR-5140-e/f-1 11 6/22/99, 2:04 PM  REMOTE CONTROL TRANSMITTER See “REMOTE CONTROL TRANSMITTER” on page 46 for full details. 1 Component selector Press the button for the component you want to control with the remote control transmitter. (The proper code must be set for your component. See “SETUP CODES” on page 53.) When the component selector has been pressed, the remote control transmitter is set to operate that component. 2 POWER When you have preset the code for a YAMAHA component, this button switches between the power on and standby mode. When you have preset the code for another manufacturer’s component, this button turns on that component if it has a remote control transmitter with a power button. * It only functions when AMP<TUNER>, TAPE/MD, CD, DVD/LD or DVD MENU on the component selector has been pressed. 3 TEST Press this button to output the test tone for each speaker. * It only functions when AMP<TUNER> on the component selector has been pressed. 4 A/B/C/D/E, PRESET +/– These buttons are used to select a preset station. * They only function when AMP<TUNER> on the component selector has been pressed. 5 MUTE Press this button to mute the sound. 6 VOLUME These buttons are used to adjust the volume. : Turns up the volume. : Turns down the volume. 7 SLEEP This button is used to set the SLEEP timer. 8 PRG+, PRG– These buttons are used to select a DSP program. * They only function when AMP<TUNER> on the component selector has been pressed. 9 Indicator This flashes in red when a button on the remote control transmitter is pressed. When it flashes rapidly several times, press the selected button again. 0 Input selector (1 to 9) 1) /Numeric buttons2) 1) These buttons are used to select the program source to be played. * They only function when AMP<TUNER>, TAPE/MD, CD or DVD/LD on the component selector has been pressed. 2) These buttons are used to select the menu or channel. * They only function when DVD MENU, VCR, CBL/DBS or TV on the component selector has been pressed. 12 05HTR-5140-e/f-1 12 6/22/99, 2:04 PM  English q EFFECT 1) 1) /CLEAR2)/+1003) This button is used to switch the DSP program on or off. * It only functions when AMP<TUNER>, TAPE/MD, CD, DVD/LD, VCR or TV on the component selector has been pressed. 2) This button is used to clear the settings. * It only functions when DVD MENU on the component selector has been pressed. 3) This button is used to select the channel. * It only functions when CBL/DBS on the component selector has been pressed. w ENTER 1) 1) /+102) This button is used to enter the channel. * It only functions when VCR, CBL/DBS or TV on the component selector has been pressed. 2) This button is used to select the menu. * It only functions when DVD MENU on the component selector has been pressed. e DISC SKIP +/– 1) 1) /CH +/–2) These buttons are used to skip to the next or previous disc. * They only function when CD, DVD/LD or DVD MENU on the component selector has been pressed. 2) These buttons are used to select the next or previous channel. * They only function when VCR, CBL/DBS or TV on the component selector has been pressed. r Operation buttons 1) 1) /Setup buttons2) These buttons function as play, stop, skip, etc. for operating the component. * They only function when TAPE/MD, CD, DVD/LD, VCR or TV on the component selector has been pressed. 2) These buttons are for adjusting various settings. * They only function when AMP<TUNER>, DVD MENU or CBL/ DBS on the component selector has been pressed. 13 05HTR-5140-e/f-1 13 6/22/99, 2:04 PM  SPEAKER SETUP SPEAKERS TO BE USED This unit is designed to provide the best sound-field quality with a 5-speaker configuration, using main speakers, rear speakers and a center speaker. The main speakers are used for the main source sound plus the effect sounds. They will probably be the speakers from your present stereo system. The rear speakers are used for the effect and surround sounds, and the center speaker is for the center sounds (dialog, vocals, etc.). If for some reason it is not practical to use a center speaker, you can do without it. Best results, however, are obtained with the full system. Use of a subwoofer expands your sound field It is also possible to further expand your system with the addition of a subwoofer and amplifier. The use of a subwoofer is effective not only for reinforcing bass frequencies from any or all channels, but also for reproducing the LFE (low frequency effect) sound with high fidelity when playing back a source that is Dolby Digital-decoded. You may wish to choose the convenience of a YAMAHA Active Servo Processing Subwoofer System, which has its own built-in power amplifier. The main speakers should be high-performance models and have enough power-handling capacity to accept the maximum output of your audio system. The other speakers do not have to be equal to the main speakers. For precise sound localization, however, it is ideal to use high-performance models that can reproduce sounds over the full-range for the center speaker and the rear speakers. SPEAKER CONFIGURATION 5-Speaker Configuration 4-Speaker Configuration This configuration is the most effective and recommended one. When playing back a source using the DSP program, DOLBY PRO LOGIC/DOLBY DIGITAL, DOLBY PRO LOGIC ENHANCED/DOLBY DIGITAL ENHANCED, 70 mm MOVIE THEATER/DIGITAL MOVIE THEATER, MONO MOVIE or TV SPORTS, or when playing back a source which contains center-channel signals (dialog, vocals, etc.) using any DSP program that is Dolby Digital-decoded, conversations will be output from the center speaker and the ambience will be excellent. Note: Set the CNTR (CENTER SPEAKER) mode to the “LARGE” or “SMALL” position. (See page 23 for details.) The center speaker is not used in this configuration. When playing back a source using the DSP program, DOLBY PRO LOGIC/DOLBY DIGITAL, DOLBY PRO LOGIC ENHANCED/ DOLBY DIGITAL ENHANCED, 70 mm MOVIE THEATER/ DIGITAL MOVIE THEATER, MONO MOVIE or TV SPORTS, or when playing back a source which contains center-channel signals (dialog, vocals, etc.) using any DSP program that is Dolby Digital-decoded, the center sound is output from the left and the right main speakers. However, the sound effect of other programs will be the same as that of the 5-speaker configuration. Note: Be sure to set the CNTR (CENTER SPEAKER) mode to the “NONE” position. (See page 23 for details.) Main L Center Main R Main L Main R Dialog Dialog Surround sound Surround sound Rear L Rear R Rear L 14 05HTR-5140-e/f-2 14 6/22/99, 2:04 PM Rear R  English SPEAKER PLACEMENT Refer to the following diagram when you place the speakers. Main speaker (R) Main: The position of your present stereo speaker system. Rear: Behind your listening position, facing slightly inward. Nearly 1.8 m (approx. 6 feet) up from the floor. Center: Precisely between the main speakers. (To avoid interference with TV sets, use a magnetically shielded speaker.) Subwoofer Center speaker Main speaker (L) Rear speaker (R) Subwoofer: The position of the subwoofer is not as critical, because low bass tones are not highly directional. Rear speaker (L) 15 05HTR-5140-e/f-2 15 6/22/99, 2:04 PM  CONNECTIONS Never plug in this unit and other components until all connections have been completed. CONNECTIONS WITH OTHER COMPONENTS When making connections between this unit and other components, be sure all connections are made correctly, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Also, refer to the owner’s manual for each component to be connected to this unit. * If you have YAMAHA components numbered as !, #, $, etc. on the rear panel, connections can be made easily by making sure to connect the output (or input) terminals of each component to the same-numbered terminals of this unit. SWITCHED AC OUTLET(S) U.S.A., Canada, Singapore, China and General models ........................................................... 2 SWITCHED OUTLETS Australia model ..................................... 1 SWITCHED OUTLET Turntable Monitor TV DVD player, LD player, etc. Use these to connect the power cords from your components to this unit. The power to the SWITCHED AC OUTLET(S) is controlled by this unit’s STANDBY/ON or the provided remote control transmitter’s POWER. These outlets will supply power to any component whenever this unit is turned on. The maximum power (total power consumption of components) that can be connected to the SWITCHED AC OUTLET(S) is 100 watts. (U.S.A. model) To AC outlet CD player Tape deck, MD recorder, etc. TV/DBS tuner VCR (Video cassette recorder) GND terminal (for turntable use) Connecting the ground (earth) wire of the turntable to the GND terminal will normally minimize hum, but in some cases, better results may be obtained with the ground wire disconnected. 16 05HTR-5140-e/f-2 16 6/22/99, 2:04 PM  English CONNECTING TO VIDEO AUX TERMINALS (ON THE FRONT PANEL) These terminals are used to connect any video input source, such as a camcorder, to this unit. VIDEO AUX Camcorder CONNECTING TO AN EXTERNAL DECODER When using the DTS or other decoder with 6-channel discrete outputs, connect the 6CH DISCRETE OUTPUT terminals of the decoder to the EXTERNAL DECODER INPUT terminals of this unit. DTS or other decoder with 6-channel discrete outputs L L R R (U.S.A. model) DVD player, LD player or other unit with digital outputs 17 05HTR-5140-e/f-2 17 6/22/99, 2:04 PM  CONNECTING TO DIGITAL (COAXIAL AND/OR OPTICAL) TERMINALS If your DVD (LD) player, TV/DBS tuner, etc. are equipped with coaxial or optical digital audio signal output terminals, they can be connected to this unit’s COAXIAL and/or OPTICAL digital signal input terminals. To make a connection between optical digital audio signal terminals, remove the cover from each terminal, and then connect them by using a commercially available optical fiber cable that conforms to EIAJ standards. Other cables might not function correctly. Even if you connect an audio/video unit to the COAXIAL (or OPTICAL) terminal of this unit, you must keep the unit connected with the same named analog audio signal terminals of this unit, because a digital signal cannot be recorded by a tape deck, MD recorder or VCR connected to this unit. You can easily switch the selection of input signals between “digital” and “analog”. (See page 30 for details.) Notes • When connecting an audio/video unit to both the digital and analog terminals of this unit, make sure to connect between terminals of the same name. • Be sure to attach the covers when the OPTICAL terminals are not being used in order to protect them from dust. • The input signal from the DVD/LD input terminals is selected in the following order of priority with the input mode set to the AUTO position: 1 COAXIAL terminal 2 OPTICAL terminal 3 Analog terminal • All digital audio signal input terminals are applicable to sampling frequencies of 32 kHz, 44.1 kHz and 48 kHz. • If your LD player has Dolby Digital RF signal output terminal and not digital signal output, use the RF demodulator (separate purchase). DVD or LD player TV/DBS tuner (U.S.A. model) 18 05HTR-5140-e/f-2 18 6/22/99, 2:04 PM  English CONNECTING SPEAKERS Main speakers A Right Main speakers B Left Right Left SPEAKERS R MAIN CENTER R L REAR (SURROUND) L Rear speakers OUTPUT Left Right SUB WOOFER Center speaker Subwoofer system Note Use speakers with the specified impedance shown on the rear panel of this unit. Main speaker connections One or two speaker systems can be connected to this unit. If you use only one speaker system, connect it to either of the SPEAKERS A or B terminals. Rear speaker connections A rear speaker system can be connected to this unit. Place them to the rear of your listening position. Center speaker connection A center speaker can be connected to this unit. Place it on or under the TV. Subwoofer connection You may wish to add a subwoofer to reinforce low frequencies or to output low bass sound from the subwoofer channel. If you have a subwoofer with built-in amplifier, including the YAMAHA Active Servo Processing Subwoofer System, connect the SUBWOOFER OUTPUT terminal of this unit to the input terminal of the subwoofer system. If you have a separate amplifier and subwoofer, connect the SUBWOOFER OUTPUT terminal of this unit to the input terminal of the subwoofer amplifier, and then connect the speaker terminals of the subwoofer amplifier to the subwoofer. When the input signals to this unit are for normal 2-channel stereo, this terminal outputs only frequencies below 90 Hz from the main and center channels. When discrete signals are input to this unit and are selected as the input source, this terminal outputs signals from the subwoofer channel. Note: The output level of signals from this terminal is adjusted by VOLUME on the front panel or VOLUME ( ) on the remote control transmitter. 19 05HTR-5140-e/f-2 19 6/22/99, 2:04 PM  How to connect Connect the SPEAKERS terminals to your speakers with wire of the proper gauge, cut as short as possible. If the connections are faulty, no sound will be heard from the speakers. Make sure that the polarity of the speaker wires is correct, that is the + and – markings are observed. If these wires are reversed, the sound will be unnatural and lack bass. Caution Do not let the bare speaker wires touch each other and do not let them touch any metal part of this unit. This could damage the unit and/or speakers. Connecting to the MAIN SPEAKERS terminals Connecting to the REAR and CENTER SPEAKERS terminals Red: positive (+) Black: negative (–) Red: positive (+) Black: negative (–) 1 Unscrew the knob. 2 Remove approx. 5 mm (1/4”) of insulation from each of the speaker wires and insert the bare wire into the terminal. 3 Tighten the knob to secure the wire. 2 1 3 1 3 2 Banana plug connections are also possible (except for the Singapore model). Simply insert the banana plug connector into the corresponding terminal. 20 05HTR-5140-e/f-2 20 6/22/99, 2:04 PM 1 Press the tab. 2 Remove approx. 5 mm (1/4”) of insulation from each of the speaker wires and insert the bare wire into the terminal. 3 Release the tab to secure the wire.  English IMPEDANCE SELECTOR SWITCH WARNING Do not change the IMPEDANCE SELECTOR switch setting while the power to this unit is on, otherwise this unit may be damaged. Select the position whose requirements your speaker system meets. (Upper position) If this unit fails to turn on when the STANDBY/ON switch is pressed, the IMPEDANCE SELECTOR switch may not be fully set to either end. If so, set the switch to either end fully when this unit is in the standby mode. IMPEDANCE SELECTOR (U.S.A. model) Main: If you use one pair of main speakers, the impedance of each speaker must be 4 Ω or higher. If you use two pairs of main speakers, the impedance of each speaker must be 8 Ω or higher. Center: The impedance of the speaker must be 6 Ω or higher. Rear: The impedance of each speaker must be 6 Ω or higher. (Lower position) Main: If you use one pair of main speakers, the impedance of each speaker must be 8 Ω or higher. If you use two pairs of main speakers, the impedance of each speaker must be 16 Ω or higher. <Canada model only> The impedance of each speaker must be 8 Ω or higher. Center: The impedance of the speaker must be 8 Ω or higher. Rear: The impedance of each speaker must be 8 Ω or higher. 21 05HTR-5140-e/f-2 21 6/22/99, 2:04 PM  ANTENNA CONNECTIONS Each antenna should be correctly connected to the designated terminals, referring to the following diagram. Both AM and FM indoor antennas are included with this unit. In general, these antennas will probably provide sufficient signal strength. Nevertheless, a properly installed outdoor antenna will give clearer reception than an indoor one. If you experience poor reception quality, an outdoor antenna may result in improvement. Indoor FM antenna (included) Outdoor FM antenna Outdoor AM antenna (U.S.A. model) AM loop antenna (included) 75-ohm/300-ohm antenna adapter 75-ohm coaxial cable 75-ohm/300-ohm antenna adapter 300-ohm feeder Ground Connecting the AM loop antenna 1 2 1 3 2 Orient so that the best reception is obtained. 3 * The AM loop antenna should be placed away from this unit. The antenna may be hung on a wall. * The AM loop antenna always should be connected, even if an outdoor AM antenna is connected to this unit. GND TERMINAL For maximum safety and minimum interference, connect the GND terminal to a good earth ground. A good earth ground is a metal stake driven into moist earth. Notes • When connecting the indoor FM antenna, firmly insert its connector into the FM ANT terminal. • If you need an outdoor FM antenna to improve FM reception quality, either 300-ohm feeder or coaxial cable may be used. In locations troubled by electrical interference, coaxial cable is preferable. 22 05HTR-5140-e/f-2 22 6/22/99, 2:04 PM  English ADJUSTMENTS BEFORE USING THIS UNIT SELECTING THE OUTPUT MODES This unit provides you the following five functions to determine the method of distributing output signals to speakers suitable for your audio system. When speaker connections have all been completed, select the proper setting for each function to make the best use of your speaker system. (See “ADJUSTMENTS IN THE ‘SET MENU’ MODE” on page 44.) 1. CNTR (CENTER SPEAKER) 4. BASS (LFE/BASS OUT) 2. REAR (REAR SPEAKERS) 5. M.LVL (MAIN LEVEL) 3. MAIN (MAIN SPEAKERS) DESCRIPTION OF EACH FUNCTION CNTR (CENTER SPEAKER) Choices: LARGE/SMALL/NONE Preset position: LARGE LARGE: Select this position when your center speaker is approximately the same size as the main speakers. SMALL: Select this position when you use a center speaker that is smaller than the main speakers. In this position, low bass signals (below 90 Hz) on the center channel are output from the main speakers (or the SUBWOOFER OUTPUT terminal if the SMALL position is selected for “MAIN” and the SW position is selected for “BASS”). NONE: Select this position when you do not have a center speaker. The center channel sound will be output from the left and right main speakers. REAR (REAR SPEAKERS) Choices: LARGE/SMALL Preset position: LARGE LARGE: Select this position if your rear speakers have high ability for bass reproduction, or a subwoofer is connected to the rear speaker in parallel. In this position, full-range signals are output from the rear speakers. SMALL: Select this position if your rear speakers do not have high ability for bass reproduction. In this position, low bass signals (below 90 Hz) on the rear channels are output from the SUBWOOFER OUTPUT terminal (or the main speakers if the MAIN position is selected for “BASS”). MAIN (MAIN SPEAKERS) Choices: LARGE/SMALL Preset position: LARGE LARGE: Select this position if your main speakers have high ability for bass reproduction. In this position, full-range signals present on the main channels are output from the main speakers. SMALL: Select this position if your main speakers do not have high ability for bass reproduction. However, if your system does not include a subwoofer, do not select this position. In this position, low bass signals (below 90 Hz) on the main channels are output from the SUBWOOFER OUTPUT terminal if the SW or BOTH position is selected for “BASS”. BASS (LFE/BASS OUT) Choices: SW/MAIN/BOTH Preset position: SW MAIN: Select this position if your system does not include a subwoofer. In this position, full-range signals present on the main channels, signals from the LFE channel and other low bass signals that are selected for “CNTR” to “MAIN” to be distributed from other channels are output from the main speakers. SW/BOTH: Select either the SW or BOTH position if your system includes a subwoofer. In either position, signals on the LFE channel and other low bass signals that are selected for “CNTR” to “MAIN” to be distributed from other channels are output from the SUBWOOFER OUTPUT terminal. When the LARGE position is selected for “MAIN”, in the SW position, no signal is distributed from the main channels to the SUBWOOFER OUTPUT terminal; however, in the BOTH position, low bass signals from the main channels are output to both the main speakers and the SUBWOOFER OUTPUT terminal. M.LVL (MAIN LEVEL) Choices: NRML (NORMAL)/–10 dB Preset position: NRML (NORMAL) NRML (NORMAL): Normally select this position. –10 dB: Select this position if the sound output from the main speakers is too loud and cannot be balanced with the sound output from the center and rear speakers. In this position, the sound output from the main speakers is attenuated. 23 05HTR-5140-e/f-2 23 6/22/99, 2:04 PM  ADJUSTING METHOD Adjustments should be made while watching the information on this unit’s display. 1 2 3 2 1 3 When adjusting with the remote control transmitter, press AMP<TUNER> on the component selector on the remote control transmitter. 3 Press + or – once or more to select the setting you want. Front panel 1 Remote control or Turn the power on. Front panel Remote control or 2 Press SET MENU once or more to select the function “CNTR” on the display. Front panel Remote control 4 Repeat steps 2 and 3 to change the setting for “REAR”, “MAIN”, “BASS” and/or “M.LVL” in the same way. or 24 05HTR-5140-e/f-2 24 6/22/99, 2:04 PM  English SPEAKER BALANCE ADJUSTMENT This procedure lets you adjust the sound output level balance between the main, center and rear speakers by using the built-in test tone generator. When this adjustment is performed, the sound output level heard at the listening position will be the same from each speaker. This is important for the best performance of the digital sound field processor, the Dolby Digital decoder and the Dolby Pro Logic Surround decoder. The adjustment of each speaker output level should be done at your listening position with the remote control transmitter. After completing the adjustment of the output level for each speaker, use VOLUME ( ) on the remote control transmitter at your listening position to check if the adjustments are satisfactory. 5,9 2 1 6 2 3 8 4 4,7 Press AMP<TUNER> on the component selector on the remote control transmitter. 2 Turn the power on. Front panel Remote control or 1 Set VOLUME to the “ ” position. Front panel 3 Select the main speakers to be used. Front panel * If you use two main speaker systems, press both A and B. 25 05HTR-5140-e/f-2 25 6/22/99, 2:04 PM  4 Set BASS, TREBLE and BALANCE to the “0” position. 6 Front panel 5 Press TEST so that “TEST LEFT” appears on the display. Remote control Turn up the volume. Remote control You will hear a test tone (like pink noise) from each speaker for about two seconds in following order: left main speaker, center speaker, right main speaker, right rear speaker and left rear speaker. The display changes as shown below. Main (L) Center Main (R) Rear (R) Rear (L) * If the function “CNTR” in the SET MENU mode is set to the NONE position, you will hear the center channel test tone from the left and right main speakers. 7 Adjust BALANCE so that the sound output level of the left main speaker and the right main speaker is the same. Front panel 26 05HTR-5140-e/f-2 26 6/22/99, 2:04 PM  Adjust the sound output levels of the center speaker and the rear speakers so that they become almost the same as that of the main speakers. Press TIME/LEVEL once or more to select the speaker to be adjusted so that “CENTER”, “R SUR.”, “L SUR.” or “SWFR” appears on the display. Remote control Notes • Once you have completed these adjustments, you can only adjust the overall sound level of your audio system by using VOLUME (or VOLUME ( ) on the remote control transmitter). • If you use external power amplifiers, you may also use their volume controls to achieve the proper balance. • If the function “CNTR” in the SET MENU mode is set to the NONE position, the sound output level of the center speaker cannot be adjusted in step 8. The center sound is automatically output from the left and right main speakers. • If there is insufficient sound output from the center and rear speakers, you may decrease the main speaker output level by setting “M.LVL” to “–10 dB”. * You cannot adjust the delay time while the test tone is sounding even if “DELAY” appears on the display after pressing TIME/LEVEL once or more. Adjust the level. * Pressing + raises and – lowers the level. * While adjusting, the test tone is fixed on the selected speaker. Remote control 9 Press TEST again to stop the test tone. Remote control 27 05HTR-5140-e/f-2 27 6/22/99, 2:04 PM English 8  BASIC OPERATIONS TO PLAY A SOURCE 2 3 1,7 7 2 3,4 5 4 8 When using the remote control transmitter • Press AMP<TUNER> on the component selector. • When controlling an audio/visual component (tape deck, MD recorder, CD player, DVD/LD player, etc.), press the button on the component selector, TAPE/MD, CD, DVD/ LD, etc., for the component you want to control. (See “SETUP CODES” on page 53.) 1 3 Select the desired program source by using INPUT. (Turn on the TV/monitor for video sources.) Front panel Remote control or Set VOLUME to the “ ” position. Front panel The name of the selected program source will appear on the display. 2 Turn the power on. Front panel Remote control or To play a tape or an MD Press TAPE/MD MON / EXT. DECODER on the front panel or TAPE/MD on the remote control transmitter so that the “TAPE/MD MON” indicator lights up on the display. To use a decoder connected to the EXTERNAL DECODER INPUT terminals Press TAPE/MD MON / EXT. DECODER once or more on the front panel or EXT. DEC. on the remote control transmitter so that “EXT. DECDR” appears on the display. 28 05HTR-5140-e/f-3 28 Front panel 6/22/99, 2:04 PM  For a DVD/LD or TV/DBS source, the current input mode is also shown. * To change the input mode for the DVD/LD or TV/DBS source, press INPUT MODE (or the button that you have pressed to select the program source in step 3 on the remote control transmitter) once or more until the desired input mode (AUTO or ANALOG) is shown on the display. (See page 30 for details on switching the input mode.) Front panel 7 Adjust the volume to the desired output level. Front panel Remote control or Remote control 8 or Input mode 5 English 4 Select the main speakers to be used. Front panel If desired, adjust BASS, TREBLE, BALANCE, etc. and use the digital sound field processor (see page 38). BASS: Turn this control clockwise to increase (or counterclockwise to decrease) the lowfrequency response. TREBLE: Turn this control clockwise to increase (or counterclockwise to decrease) the highfrequency response. BALANCE: Adjust the balance of the output volume from the left and right speakers to compensate for sound imbalance caused by the speaker location or listening room conditions. Front panel * If you use two main speaker systems, press both A and B. 6 Play the source. (See page 32 for detailed information on tuning.) * These controls are only effective for the sound from the main speakers. When you have finished using this unit Press STANDBY/ON on the front panel again or POWER on the remote control transmitter to set this unit to the standby mode. 29 05HTR-5140-e/f-3 29 6/22/99, 2:04 PM  Notes on using INPUT • The audio source selected by INPUT will not be played if the “TAPE/MD MON” indicator lights up or if “EXT. DECDR” is displayed. • If you select INPUT for a video source without canceling the selection of TAPE/MD MON / EXT. DECODER on the front panel (or TAPE/MD or EXT. DEC. on the remote control transmitter), the play back result will be a video image from the video source and the sound from the audio source selected by TAPE/MD MON / EXT. DECODER on the front panel (or TAPE/MD or EXT. DEC. on the remote control transmitter). • Once you start playing a video source, the video image will not be interrupted even if INPUT for an audio source is selected. • When you select a program source by using INPUT, the DSP program (or no DSP program) that was being used when the same program source was selected the last time, will be automatically recalled. Switching the input mode (for DVD/LD and TV/DBS) This unit allows you to switch the input mode only for those sources connected to the DVD/LD and TV/DBS input terminals (on the rear panel of this unit) that input two or three types of signal. The following two input modes are provided: AUTO For a source connected to the DVD/LD input terminals This mode is automatically selected when you turn on the power to this unit. In this mode, the input signal is automatically selected in the following order of priority: 1. Digital input signal from the COAXIAL terminal 2. Digital input signal from the OPTICAL terminal 3. Analog input signal For a source connected to the TV/DBS input terminals This mode is selected when you turn on the power to this unit if the AUTO position is selected for “INPUT” in the SET MENU mode. (See page 45 for details.) In this mode, the input signal is automatically selected in the following order of priority: 1. Digital input signal from the OPTICAL terminal 2. Analog input signal ANALOG In this mode, only an analog input signal is selected, even if a digital signal is input at the same time. Select this mode when you want to use the analog input signal instead of the digital input signal. Notes on input mode selection • To play back a source that is Dolby Digital-decoded, set the input mode to AUTO. • For the TV/DBS source only, the input mode selected for “INPUT” in the SET MENU mode is effective when you turn on the power to this unit. • When you want to enjoy a source which has normal 2-channel signals with a Dolby Pro Logic Surround program, select the ANALOG mode. • In the AUTO mode, there may be a case, depending on the LD player or DVD player, that when you search for a source encoded with Dolby Digital during play and then play is restored, the sound output is interrupted for a moment because the digital input signal is selected again. 30 05HTR-5140-e/f-3 30 6/22/99, 2:04 PM  English TO RECORD A SOURCE ON TAPE OR MD 4 1 2 2 1,4 1 4 Select the source to be recorded. Front panel Remote control When a tape deck or MD recorder is being used for recording, you can monitor the sounds being recorded by pressing TAPE/MD MON / EXT. DECODER on the front panel or TAPE/MD on the remote control transmitter so that the “TAPE/MD MON” indicator lights up on the display. Front panel or Remote control or 2 Play the source and then turn up the volume to confirm the program source. (See page 32 for detailed information on tuning.) Front panel Remote control or 3 Notes • The settings of DSP and VOLUME, BASS, TREBLE and BALANCE have no effect on the material being recorded. • A source that is connected to this unit only through the digital terminals cannot be recorded by a tape deck, MD recorder or VCR connected to this unit. • Please check the copyright laws in your country to record from records, compact discs, radio, etc. Recording of copyright material may infringe copyright laws. If you use a video source that has scrambled or encoded signals to prevent it from being dubbed, there may be a case that the picture itself will be affected by those signals. Begin recording on the tape deck, MD recorder or VCR connected to this unit. 31 05HTR-5140-e/f-3 31 6/22/99, 2:04 PM  TUNING OPERATIONS Set INPUT on the front panel to the TUNER position. When using the remote control transmitter, press AMP<TUNER> on the component selector and then press TUNER on the input selector. Normally, if station signals are strong and there is no interference, quick automatic-search tuning (AUTOMATIC TUNING) is possible. However, if the signal from the station you want to select is weak, you must tune in to it manually (MANUAL TUNING). 2 3 1 AUTOMATIC TUNING 1 MANUAL TUNING Select the reception band (FM or AM) and confirm it on the display. 1 Front panel Select the reception band (FM or AM) and confirm it on the display. Front panel or 2 Press TUNING MODE so that the “AUTO TUNING” indicator lights up on the display. or 2 Press TUNING MODE. Front panel Front panel Confirm that the “AUTO TUNING” indicator goes off. Lights up 3 To tune in to a higher frequency, press the UP side of TUNING once. To tune in to a lower frequency, press the DOWN side of TUNING once. 3 Tune in manually to the desired station. Front panel Front panel * To continue the tuning search, press and hold the button. * If the station where the tuning search stops is not the desired one, press once more. * If the tuning search does not stop at the desired station (because the signal from the station is weak), take the manual tuning procedure. Note If you tune in manually to an FM station, it will be automatically received in monaural mode to increase the signal quality. 32 05HTR-5140-e/f-3 32 6/22/99, 2:04 PM  English MANUAL PRESET TUNING This unit can store station frequencies to be selected by tuning. With this function, you can recall any desired station simply by selecting the preset station number with which it was stored. Up to 40 stations (8 stations x 5 groups) can be stored. 2 4 3 To store stations 1 2 Tune in to the desired station. (See the previous page for the tuning procedure.) 4 Select the preset station number with which you want to store the station before the “MEMORY” indicator goes off from the display. Front panel Press A/B/C/D/E once or more to select the desired group (A to E) of preset stations and confirm it on the display. Front panel 3 Press MEMORY so that the “MEMORY” indicator flashes for about five seconds. Front panel The displayed station has been stored as A1. * In the same way, store other stations as A2, A3 ... A8. * You can store more stations as preset station numbers in other groups in the same way by selecting another group in step 2. Flashes 33 05HTR-5140-e/f-3 33 6/22/99, 2:04 PM  1 2 1 2 To recall a preset station 1 Select the group of preset stations. Front panel Remote control Memory back-up The memory back-up circuit prevents the stored data from being lost when this unit is set in the standby mode. If, however, the power plug is disconnected from the AC outlet or the power is cut due to temporary power failure for more than one week, the memory will be erased. If so, it can be re-stored by simply following the preset tuning procedure. or 2 Select the preset station number. Front panel Notes • A new setting can be stored in place of the former one. • For presets, the setting of the reception mode (stereo or monaural) is stored along with the station frequency. Remote control or 34 05HTR-5140-e/f-3 34 6/22/99, 2:04 PM  English AUTOMATIC PRESET TUNING (for FM stations only) You can also make use of the automatic preset tuning function for FM stations only. This function enables the unit to perform automatic tuning and to sequentially store FM stations with strong signals. Up to 40 stations can be stored automatically in the same way as that for manual preset tuning on page 33. Note that a new setting can be stored in place of the former one. 3 1 2 4 To store stations 1 4 Select the FM band. Front panel To tune in to higher frequencies, press the UP side of TUNING once. To tune in to lower frequencies, press the DOWN side of TUNING once. Front panel 2 Press TUNING MODE so that the “AUTO TUNING” indicator lights up on the display. * If TUNING is not pressed, the automatic preset tuning soon begins automatically toward higher frequencies. Front panel Lights up 3 Automatic preset tuning begins from the frequency currently displayed. Received stations are sequentially stored as A1, A2 ... A8. * If more than 8 stations are received, they are stored as the preset station numbers in other groups (B, C, D and E) in that order. Press MEMORY and hold for about three seconds. Front panel Flashes If you want to store the first station received by automatic preset tuning as a desired preset station number For example, if you want to store the first received station as C5, select “C5” while “A1”, the “MEMORY” indicator and the “AUTO TUNING” indicator flash after pressing MEMORY in step 3. Then press TUNING. The first received station is stored as C5, and the next stations as C6, C7 ... sequentially. If stations have been stored up to E8, automatic preset tuning automatically stops. When automatic preset tuning is complete The display shows the frequency of the last preset station. Check the contents and the number of preset stations by following the procedure in the section “To recall a preset station” on page 34. 35 05HTR-5140-e/f-3 35 6/22/99, 2:04 PM  Notes • You can manually replace a preset station with another FM or AM station by simply following the procedure in the section “To store stations” on page 33. • Even if the number of received stations is not enough to be stored up to E8, the search is automatically ended after searching all frequencies. • With this function, only FM stations with sufficient signal strength are automatically stored. If the station you want to store is weak in signal strength, tune in to it manually in monaural sound and store it by following the procedure in the section “To store stations” on page 33. EXCHANGING PRESET STATIONS You can exchange the assigment of two preset stations with each other as shown below. 2,4 Example If you want to change the preset station from “E1” to “A5”, or vice versa. 1 2 Recall preset station “E1” by following the procedure in the section “To recall a preset station” on page 34. 3 Next, recall preset station “A5” by following the same procedure as in step 1. Press EDIT. Front Panel Flashes Flashes 4 Press EDIT once more. Front Panel Shows the exchange of stations has been completed. 36 05HTR-5140-e/f-3 36 6/22/99, 2:05 PM  English SETTING THE SLEEP TIMER The SLEEP timer can be used to make this unit automatically switch to the standby mode. When you are going to sleep while enjoying a broadcast or other desired program source, this timer function is useful. The SLEEP timer can only be controlled with the remote control transmitter. Notes • To set the SLEEP timer for this unit, press AMP<TUNER>, TAPE/MD, CD or DVD/LD on the component selector. • The components for which the SLEEP timer is effective are the sources connected to the SWITCHED AC OUTLET(S) on the rear panel of this unit. 1 To set the SLEEP time 1 To cancel the selected SLEEP time Press SLEEP once or more to select the desired SLEEP time. Remote control Remote control Press SLEEP once or more so that “SLEEP OFF” appears on the display. (It will soon disappear and the “SLEEP” indicator will go off from the display.) The SLEEP time is displayed. Flashes Note The SLEEP timer setting can also be canceled by setting the unit in the standby mode with STANDBY/ON on the front panel (or POWER on the remote control transmitter) or by disconnecting the power plug of the unit from the AC outlet. Each time you press SLEEP, the SLEEP time will change as follows: (Minutes) 120 90 60 30 The SLEEP timer is off (SLEEP OFF). (This is the state before SLEEP is pressed.) The “SLEEP” indicator soon lights up and the display returns to the indication before the SLEEP timer was set. 2 The unit will be switched to the standby mode automatically at the selected SLEEP time. 37 05HTR-5140-e/f-3 37 6/22/99, 2:05 PM  USING THE DIGITAL SOUND FIELD PROCESSOR (DSP) This unit incorporates a sophisticated, multi-program digital sound field processor. The processor allows you to electronically expand and change the shape of the audio sound field from both audio and video sources, creating a theater-like experience in your listening room. You can create outstanding audio sound by selecting a suitable sound field program (this will, of course, depend on what you are listening to) and adding any desired adjustments. The following list gives you a brief description of the sound fields produced by each of the DSP programs. Keep in mind that most of these are precise digital re-creations of actual acoustic environments. The data for these sound fields were recorded at actual locations using sophisticated sound field measurement equipment. Note The channel level balance between the left and right rear speakers may vary depending on the sound field you are listening to. This is due to the fact that most of these sound fields are a re-creation of actual acoustic environments. BRIEF OVERVIEW OF DIGITAL SOUND FIELD PROGRAMS No. 1 PROGRAM DOLBY PRO LOGIC ( ) This functions when the input signal is analog or PCM audio, or encoded with Dolby Digital in 2-channel. Speaker output: main, center, rear DOLBY DIGITAL ( ) This functions when the input signal is encoded with Dolby Digital (not in 2-channel). Speaker output: main, center, rear FEATURES This reproduces video discs, video tapes and similar sources which are Dolby Surround encoded and bear the “DOLBY SURROUND” logo. The built-in Dolby Pro Logic Surround decoder or Dolby Digital decoder precisely reproduces the sounds and sound effects of a source encoded with Dolby Surround. The realization of a highly efficient decoding process improves crosstalk and channel separation and makes sound positioning smoother and more precise. Note: If the main channel sound is considerably altered by overadjusting BASS or TREBLE, it may not produce suitable surround sound. 2 DOLBY PRO LOGIC ENHANCED ( ) This functions when the input signal is analog or PCM audio, or encoded with Dolby Digital in 2-channel. Speaker output: main, center, rear DOLBY DIGITAL ENHANCED ( ) This functions when the input signal is encoded with Dolby Digital (not in 2-channel). Speaker output: main, center, rear 3 70 mm MOVIE THEATER ( ) This functions when the input signal is analog or PCM audio, or encoded with Dolby Digital in 2-channel. Speaker output: main, center, rear DIGITAL MOVIE THEATER ( ) This functions when the input signal is encoded with Dolby Digital (not in 2-channel). Speaker output: main, center, rear This reproduces video discs, video tapes and similar sources which are Dolby Surround encoded and bear the “DOLBY SURROUND” logo. This program ideally simulates the multi-surround speaker systems of the 35 mm film theater. Dolby Surround decoding is precisely performed without altering the original sound orientation. The surround effects produced by this sound field fold around the viewer naturally from the rear to the left and right and toward the screen. This is ideal for reproducing video discs, video tapes and similar sources which are Dolby Surround encoded and bear the “DOLBY SURROUND” logo. This program is ideal for precisely reproducing the sound design of the newest 70 mm/Dolby Digital multi-track films. The sound field is similar to that of the newest movie theaters, so the reverberations of the sound field itself are restrained as much as possible. The three-dimensional feeling of the sound field is emphasized, and dialog is precisely oriented on the screen. You can enjoy watching Sci-Fi, adventure movies, etc. with considerable presence. 38 05HTR-5140-e/f-4 38 6/22/99, 2:05 PM  PROGRAM FEATURES 4 MONO MOVIE ( ) This functions when the input signal is analog or PCM audio, or encoded with Dolby Digital in 2-channel. Speaker output: main, center, rear ( ) This functions when the input signal is encoded with Dolby Digital (not in 2-channel). Speaker output: main, center, rear This program is designed specifically to enhance mono audio sources. Compared to a strictly mono setting, the sound image created in this mode is wider and slightly forward of the speaker pair, lending an immediacy to the overall sound. It is particularly effective when used with old mono movies, news broadcasting and dialog. 5 TV SPORTS ( ) This functions when the input signal is analog or PCM audio, or encoded with Dolby Digital in 2-channel. Speaker output: main, center, rear ( ) This functions when the input signal is encoded with Dolby Digital (not in 2-channel). Speaker output: main, center, rear This program is furnished with a tight sound field in which the sound will not spread excessively on the front side, but the rear surround side produces dynamic sound expansion. This program is the most suitable for sports events. 6 DISCO ( ) This functions when the input signal is analog or PCM audio, or encoded with Dolby Digital in 2-channel. Speaker output: main, rear ( ) This functions when the input signal is encoded with Dolby Digital (not in 2-channel). Speaker output: main, center, rear This program re-creates the acoustic environment of a lively disco in the heart of a very lively city. The sound is dense and highly concentrated. It is also characterized by a high-energy, “immediate” sound. 7 ROCK CONCERT ( ) This functions when the input signal is analog or PCM audio, or encoded with Dolby Digital in 2-channel. Speaker output: main, rear ( ) This functions when the input signal is encoded with Dolby Digital (not in 2-channel). Speaker output: main, center, rear This program is ideally suited for rock music. You will experience a very dynamic and lively sound field. 8 CONCERT HALL ( ) This functions when the input signal is analog or PCM audio, or encoded with Dolby Digital in 2-channel. Speaker output: main, rear ( ) This functions when the input signal is encoded with Dolby Digital (not in 2-channel). Speaker output: main, center, rear In this program, the center will appear to be deep behind the main speakers, creating an expansive, large hall ambience. Orchestra and opera music are suited to this sound field. Note: When the NONE position is selected for “CNTR” in the SET MENU mode, no sound is output from the center speaker(s). 39 05HTR-5140-e/f-4 39 6/22/99, 2:05 PM English No.  PLAYING AN AUDIO/VIDEO SOURCE WITH THE DIGITAL SOUND FIELD PROCESSOR (DSP) EFFECT 2 2 1 2 Follow steps 1 to 7 shown in “BASIC OPERATIONS” on pages 28 to 29. Select the desired DSP program that is suitable for the source. When using the remote control transmitter, press AMP<TUNER> on the component selector first. Front panel Remote control or 3 If desired, adjust the delay time and the output level of each speaker. (See pages 42 and 43 for details.) Notes • You can select a program for each of the program sources. Once you select a program, it is linked with the program source selected at that time. So, when you select the program source next time, the same program is automatically called. • If you prefer to cancel the DSP function, press EFFECT. The sound will be that of normal 2-channel stereo without a surround sound effect. • When a monaural sound source is played with DOLBY PRO LOGIC or DOLBY PRO LOGIC ENHANCED, no sound can be heard from the main speakers and the rear speakers. Sound is heard only from the center speaker. However, if the NONE position is selected for “CNTR” in the SET MENU mode, the main speakers output the sound of the center channel. The name of the selected program appears on the display. 40 05HTR-5140-e/f-4 40 6/22/99, 2:05 PM  English This unit incorporates a Dolby Digital decoder and a Dolby Pro Logic Surround decoder for multi-channel sound reproduction of sources encoded with Dolby Surround. The operation of these decoders can be controlled by selecting a corresponding DSP program including the combined operation of YAMAHA DSP and Dolby Digital or Dolby Pro Logic Surround. To enjoy a video source with Dolby Pro Logic Surround or Dolby Digital-decoded When you select the DOLBY PRO LOGIC/DOLBY DIGITAL, DOLBY PRO LOGIC ENHANCED/DOLBY DIGITAL ENHANCED or 70 mm MOVIE THEATER/DIGITAL MOVIE THEATER program, and the input signal of the source is 2-channel stereo, Dolby Pro Logic Surround is decoded. When a program is selected and the input signal of the source is encoded with Dolby Digital, Dolby Digital is automatically decoded. To cancel the sound effect EFFECT on the front panel and on the remote control transmitter make it simple to compare the normal stereo sound with the fully processed sound effect. To cancel the sound effect and monitor only the main sound, press EFFECT. Press EFFECT once more to turn sound effect on. Front panel * The following indicators on the display show you what sound processing is being undertaken. This lights up when Dolby Digital is being decoded and the input signal of the selected source encoded with Dolby Digital is not in 2-channel. This lights up when the digital sound field processor is turned on. This lights up when Dolby Pro Logic Surround is being decoded. Remote control or Notes • If the sound effect is canceled when signals encoded with Dolby Digital are input to this unit, the signals of all channels are mixed and are output from the main speakers. • If EFFECT is pressed to turn sound effects off when Dolby Digital is decoded, it may happen that the sound is output faintly or not output normally, depending on the source. In that case, press EFFECT to turn sound effects on, or use input signals not encoded with Dolby Digital. * In addition, for the DOLBY PRO LOGIC/DOLBY DIGITAL, DOLBY PRO LOGIC ENHANCED/DOLBY DIGITAL ENHANCED or 70 mm MOVIE THEATER/DIGITAL MOVIE THEATER program, the name of the program on the display will change according to the type of decoding. (See page 38 for details.) Note If the input signal of the source is encoded with Dolby Digital in 2-channel only, their sound processing is similar to that for analog or PCM audio signals. 41 05HTR-5140-e/f-4 41 6/22/99, 2:05 PM  ADJUSTING THE DELAY TIME AND SPEAKER OUTPUT LEVELS When using the digital sound field processor with the Dolby Pro Logic Surround decoder or the Dolby Digital decoder, you can adjust the delay time between the main sound and sound effect, and each speaker’s output level as you prefer. 1 2 1 2 Adjusting method When adjusting with the remote control transmitter, press AMP<TUNER> on the component selector. 2 Press + or – to adjust the settings for the delay time or speaker output levels. Front panel Remote control or 1 Press TIME/LEVEL once or more until the name of the item which you want to adjust appears on the display. Front panel Remote control 3 Repeat steps 1 to 2 to adjust the settings of any other item. or When pressed, the selection changes as follows: DELAY CENTER Delay time Center speaker output level R SUR. Right rear speaker output level L SUR. Left rear speaker output level SWFR Subwoofer output level * Depending on the setting in the SET MENU mode, you may not be able to select all items. 42 05HTR-5140-e/f-4 42 6/22/99, 2:05 PM  You can adjust the time difference between the beginning of the sound from the main speakers and the beginning of the sound effect from the rear speakers. The larger the value, the later the sound effect is generated. This adjustment can be individually made to all programs. Notes • Adding too much delay will cause an unnatural effect with some sources. • When + or – is pressed, the sound is momentarily interrupted. Program Control range (ms) Preset value 1. 15 to 30 0 to 15 15 to 30 0 to 15 15 to 30 1 to 99 1 to 99 1 to 99 1 to 99 1 to 99 1 to 99 20 5 20 5 20 16 49 9 40 16 44 2. 3. 4. 5. 6. 7. 8. DOLBY PRO LOGIC DOLBY DIGITAL DOLBY PRO LOGIC ENHANCED DOLBY DIGITAL ENHANCED 70 mm MOVIE THEATER DIGITAL MOVIE THEATER MONO MOVIE TV SPORTS DISCO ROCK CONCERT CONCERT HALL English Adjusting the delay time Adjusting the output level of the center, right rear and left rear speakers, and subwoofer If desired, you can adjust the sound output level of each speaker even if the output level has already been set in “SPEAKER BALANCE ADJUSTMENT” on pages 25 to 27. Notes • The output level of the center speaker cannot be adjusted when the DISCO, ROCK CONCERT or CONCERT HALL program is selected, and the input signal is analog, PCM audio, or encoded with Dolby Digital in 2-channel format. • If the function “CNTR” in the SET MENU mode is set to the NONE position, the sound output level of the center speaker cannot be adjusted. This is because, in this mode, the center sound is automatically output from the left and right main speakers. • Once the output level has been adjusted, the level will be the same for all digital sound field programs. Speakers Control range (dB) Preset value CENTER RIGHT REAR LEFT REAR SUBWOOFER MIN, –20 to +10 MIN, –20 to +10 MIN, –20 to +10 MIN, –20 to 0 0 0 0 0 Memory back-up The memory back-up circuit prevents the stored data from being lost when this unit is set in the standby mode. If, however, the power plug is disconnected from the AC outlet or the power is cut due to temporary power failure for more than one week, the values for the delay time and the center/rear/subwoofer output levels you set the last time will automatically return to the preset values. If so, they can be re-set by simply following the adjusting method on page 42. 43 05HTR-5140-e/f-4 43 6/22/99, 2:05 PM  ADJUSTMENTS IN THE “SET MENU” MODE The following ten types of functions maximize the performance of your system and expand your enjoyment for audio listening and video watching. 1. 2. 3. 4. 5. CNTR (CENTER SPEAKER) REAR (REAR SPEAKERS) MAIN (MAIN SPEAKERS) BASS (LFE/BASS OUT) M.LVL (MAIN LEVEL) For details on “CNTR”, “REAR”, “MAIN”, “BASS” and “M.LVL”, see page 23. (Once you have selected the appropriate modes, you do not have to change settings unless any alteration is made in your speaker system.) LFE [Adjusting the output level of the LFE (low frequency effect) channel] Control range: –20 dB to 0 dB (in 1 dB steps) Preset value: 0 dB * This adjustment is effective only when Dolby Digital is decoded and the signals of the selected source encoded with Dolby Digital contain LFE signals. This adjusts the output level of the LFE channel. If the LFE signals are mixed with signals of other channels to output them from the same speakers, the ratio of the LFE signal level to the level of the other signals is adjusted. (See page 7 for details about the LFE channel.) 6. 7. 8. 9. 10. LFE (LFE LEVEL) D.RNG (DYNAMIC RANGE) C.DELAY (CENTER DELAY) GUARD (MEMORY GUARD) INPUT (INPUT MODE) D.RNG (Adjusting the dynamic range) Choices: MAX/STD/MIN Preset position: MAX * This adjustment is effective only when Dolby Digital is decoded. MAX: “Dynamic range” is the difference between the maximum level and the minimum level of sounds. Sounds on a movie originally designed for movie theaters feature very wide dynamic range. Dolby Digital technology can modify the original sound track into a home audio format with this wide dynamic range unchanged. In this position, a source encoded with Dolby Digital is reproduced in the original sound track’s wide dynamic range providing you with powerful sounds just like those in a movie theater. Selecting this position will be even better if you can listen to a source at a high output level in a room specially soundproofed for audio/video enjoyment. STD (Standard): Powerful sounds of extremely wide dynamic range are not always suitable for home use. Depending on the condition of your listening environment, it may not be possible to increase the sound output level as high as that in a movie theater. However, at the normal level suitable for listening to in your room, the low-level parts of source sound often cannot be heard well because they will be lost among noise in your environment. Dolby Digital technology has also made it possible to reduce an original sound track’s dynamic range for a home audio format by “compressing” the sound data. In this position, a source encoded with sound Dolby Digital is reproduced in the “compressed” dynamic range of sound that is suitable for low-level listening. MIN: In this position, the dynamic range is more reduced than in the STD position. Selecting this position will be effective when you must listen to a source at a low level. 44 05HTR-5140-e/f-5 44 6/22/99, 2:05 PM  Control range: 0 ms to 5 ms (in 1 ms steps) Preset value: 0 ms * This adjustment is effective only when Dolby Digital is decoded and the signals of the selected source encoded with Dolby Digital contain center-channel signals. This adjusts the delay between the main sound (on the main channels) and dialog, etc. (on the center channel). The larger the value, the later the dialog, etc. is generated. This is for making sounds from the left main, center and right main speakers reach your listening position at the same time. This is achieved by delaying the sound from the center speaker if the distance from the center speaker to your listening position is shorter than the distance from the left or right main speaker to your listening position. Adjusting method Adjustments should be made while watching the information on this unit’s display. When adjusting with the remote control transmitter, press AMP<TUNER> on the component selector. Press SET MENU once or more so that the function which you want to change appears on the display. Front panel Choices: ON/OFF Preset position: OFF or Front panel If you wish to prevent accidental alterations to SET MENU and other adjustments on this unit, select ON. The following functions on this unit can be locked by this operation: • Functions in the SET MENU mode • Functions in the TIME/LEVEL mode • Functions when using TEST INPUT (Selecting the initial input mode of the sources connected to the TV/DBS input terminals) Choices: AUTO/LAST Preset position: AUTO You can designate the input mode that is automatically selected when the power for this unit is switched on for only the sources connected to the TV/DBS input terminals of this unit. LAST: Remote control Press + or – to select any desired setting or to edit parameters of the function. GUARD AUTO: English C.DELAY [Adjusting the delay of center sounds (dialog, etc.)] Remote control or Repeat these steps to change or adjust the settings of any other function. Memory back-up The memory back-up circuit prevents the stored data from being lost when this unit is set in the standby mode. If, however, the power plug is disconnected from the AC outlet or the power is cut due to temporary power failure for more than one week, the settings of the SET MENU mode will automatically return to the factory settings. If so, they can be re-set by simply following the procedure above. In this position, the AUTO input mode is always selected when the power for this unit is switched on. In this position, the input mode you selected last time is memorized and will not be changed when the power is switched on again. * See page 30 for details on switching the input mode. 45 05HTR-5140-e/f-5 45 6/22/99, 2:05 PM  REMOTE CONTROL TRANSMITTER You can use the remote control transmitter to control not only this unit but also other components connected to it. The remote control transmitter is factory set to control this unit and most YAMAHA audio components. To control other brands of components, you must preset the remote control transmitter with manufacturers’ codes listed on pages 113 to 117. Components which can be controlled There are eight buttons on the component selector that you can select to control connected components with this remote control transmitter. For example, if CD on the component selector is pressed, the remote control transmitter selects the CD operation mode, allowing the CD player to be operated by the buttons on the remote control transmitter. AMP<TUNER> You can perform the basic operations of this unit, set the speaker level, and set the DSP level and delay time in the AMP<TUNER> mode. TAPE/MD The code for a YAMAHA tape deck is preset. (The code for the YAMAHA MD recorder can also be preset.) CD The code for a YAMAHA CD player is preset. VCR A VCR can be controlled. DVD/LD & DVD MENU An LD player can be controlled in the DVD/LD mode. A DVD player can be controlled in the DVD/LD and DVD MENU modes. The code for a YAMAHA DVD player is preset. If the remote control transmitter will not operate your YAMAHA DVD player, you need to preset code number “0048”. CBL/DBS A cable television or DBS tuner can be controlled. TV A television can be controlled. Notes 1. You can preset the code for the manufacturer of your component after pressing the shaded buttons in the illustration above. Note that you can preset only one code for one mode. See “SETUP CODES” on page 53 for details. 2. In the DVD/LD and DVD MENU modes: • Be sure to press DVD/LD on the component selector before presetting the code for the DVD/LD player. The code preset in the DVD/LD mode is also simultaneously preset in the DVD MENU mode. You cannot preset the code for a DVD player in the DVD MENU mode. • DVD MENU operations cannot be performed for some DVD players. 3. When using a second (and third) VCR: (See “To use a second (and third) VCR” on page 53 for details.) • If you are not using a CBL/DBS (cable TV or DBS tuner), the second (or third) VCR can be preset in the CBL/DBS mode. • If you are not using a DVD player, the second (or third) VCR can be preset in the DVD MENU mode. Note that in this case you must preset the code for an LD player in the DVD/LD mode even if an LD player is not being used. 46 05HTR-5140-e/f-6 46 6/22/99, 2:05 PM  ■ AMP<TUNER> MODE Note: TV VOLUME and TV INPUT function if you have preset the code for your TV. Press AMP<TUNER>. POWER Each time this button is pressed, the unit will switch between the power on and standby modes. TEST This button outputs a test tone for adjusting the output levels of the speakers. A/B/C/D/E & PRESET +/– These buttons select a preset FM or AM broadcast. A/B/C/D/E: To select a group of preset stations. PRESET +/–: To select the preset station number. MUTE This button mutes the sound. To cancel mute, press this button once more, or press any operation buttons of this unit. Input selector These buttons select the program source. CD: To play a CD TUNER: To listen to an FM or AM broadcast TAPE/MD: To play a tape or MD DVD/LD: To play a DVD or LD TV/DBS: To watch a television or satellite broadcast VCR: To play a video tape PHONO: To play an analog record V-AUX: To use a camcorder EXT. DEC.: To output the signals of a DTS or other multi-channel decoder EFFECT This button switches the DSP program on or off. TV VOLUME VOLUME ( ) These buttons adjust the volume level. SLEEP This button sets the SLEEP timer. +/– These buttons adjust the settings of the SET MENU mode and the TIME/LEVEL mode. TIME/LEVEL This button selects the item in the TIME/LEVEL mode. TV INPUT PRG+/PRG– These buttons select a DSP program. SET MENU This button selects functions in the SET MENU mode. 47 05HTR-5140-e/f-6 47 6/22/99, 2:05 PM English The lightly marked buttons do not function.  The lightly marked buttons do not function. Please refer to the owner’s manual for details of each component. ■ TAPE/MD MODE Notes: • TV VOLUME functions if you have preset the code for your TV. • The code for the YAMAHA MD recorder can be preset. Press TAPE/MD. POWER (TAPE) When you have preset the code for a YAMAHA tape deck, this button turns the unit on. When you have preset the code for another manufacturer, this button turns on that component if it has a remote control transmitter with a power button. (MD) When you have preset the code for the YAMAHA MD recorder, this button turns the unit on. INPUT EFFECT VOLUME MUTE SLEEP REC/PAUSE This button pauses recording on a tape deck or MD recorder. PLAY This button plays a tape or an MD. DIR A (TAPE) This button selects the playing direction of deck A. SKIP– (MD) This button skips to the previous track. REWIND (TAPE) This button rewinds a tape. SEARCH (MD) This button initiates a backward search on the track that is playing to find the point from which you want to listen. TV VOLUME DISPLAY (MD) DECK A/B (TAPE) This button selects double-cassette tape deck A or B. PAUSE (MD) This button gives a pause in operation. DIR B (TAPE) This button selects the playing direction of deck B. SKIP+ (MD) This button skips to the next track. STOP This button stops operation of a tape or MD. FAST FORWARD (TAPE) This button winds a tape fast forward. SEARCH (MD) This button initiates a fast-forward search on the track that is playing to find the point from which you want to listen. 48 05HTR-5140-e/f-6 48 6/22/99, 2:05 PM  ■ CD MODE Note: TV VOLUME and TV INPUT function if you have preset the code for your TV. Press CD. POWER When you have preset the code for a YAMAHA CD player, this button turns the unit on. When you have preset the code for another manufacturer, this button turns on that component if it has a remote control transmitter with a power button. INPUT EFFECT DISC SKIP +/– (for the CD player with CD changer) These buttons skip to the next or previous CD. VOLUME MUTE SLEEP PLAY This button plays a CD. SKIP– This button skips to the previous track. SEARCH This button initiates a backward search on the track that is playing to find the point from which you want to listen. TV VOLUME DISPLAY TV INPUT PAUSE This button gives a pause in operation. The button functions as PAUSE/STOP* for operating YAMAHA CD player under factory setting. SKIP+ This button skips to the next track. STOP This button stops operation. The button functions as PAUSE/STOP* for operating YAMAHA CD players. SEARCH This button initiates a fast-forward search on the track that is playing to find the point from which you want to listen. * PAUSE/STOP function ... Press the button once to give a pause in operation and once more to stop operation. 49 05HTR-5140-e/f-6 49 6/22/99, 2:05 PM English The lightly marked buttons do not function. Please refer to the owner’s manual for details of each component.  The lightly marked buttons do not function. Please refer to the owner’s manual for details of each component. ■ DVD/LD MODE Note: TV VOLUME and TV INPUT function if you have preset the code for your TV. Press DVD/LD. POWER (DVD) When you have preset the code for a YAMAHA DVD player, this button turns the unit on. When you have preset the code for another manufacturer, this button turns on that component if it has a remote control transmitter with a power button. (LD) When you have preset the code for a YAMAHA LD player, this button turns the unit on. When you have preset the code for another manufacturer, this button turns on that component if it has a remote control transmitter with a power button. INPUT EFFECT DISC SKIP +/– VOLUME MUTE SLEEP SKIP– STOP TV VOLUME DISPLAY TV INPUT PAUSE SKIP+ PLAY SEARCH SEARCH ■ DVD MENU MODE Note: TV VOLUME and TV INPUT function if you have preset the code for your TV. Press DVD MENU. POWER When you have preset the code for a YAMAHA DVD player, this button turns the unit on. When you have preset the code for another manufacturer, this button turns on that component if it has a remote control transmitter with a power button. Numeric buttons CLEAR +10 DISC SKIP +/– VOLUME MUTE RETURN MENU UP MENU LEFT MENU SELECT TITLE TV VOLUME INDEX TV INPUT MENU RIGHT MENU DOWN MENU 50 05HTR-5140-e/f-6 50 6/22/99, 2:05 PM  English The lightly marked buttons do not function. Please refer to the owner’s manual for details of each component. ■ VCR MODE ■ TV MODE Note: TV VOLUME, TV INPUT and TV SLEEP function if you have preset the code for your TV. Note: You can control your VCR if you have preset the code for it. Press VCR. Press TV. VCR POWER TV POWER CHANNEL CHANNEL EFFECT EFFECT CHANNEL ENTER VCR CHANNEL +/– CHANNEL ENTER TV CHANNEL +/– VOLUME VOLUME TV VOLUME MUTE TV SLEEP VCR REC Press this button twice to start recording. DISPLAY TV INPUT VCR PAUSE VCR PLAY VCR STOP VCR FAST FORWARD VCR REWIND TV MUTE TV SLEEP VCR REC Press this button twice. VCR PLAY VCR REWIND TV VOLUME DISPLAY TV INPUT VCR PAUSE VCR STOP VCR FAST FORWARD ■ CBL/DBS MODE Note: TV VOLUME, TV INPUT and TV SLEEP function if you have preset the code for your TV. Press CBL/DBS. CBL/DBS POWER CHANNEL +100 CHANNEL ENTER CBL/DBS CHANNEL +/– VOLUME MUTE TV SLEEP TV VOLUME DISPLAY TV INPUT MENU LEFT MENU UP MENU RIGHT MENU SELECT RECALL MENU DOWN MENU 51 05HTR-5140-e/f-6 51 6/22/99, 2:05 PM  NOTES ABOUT THE REMOTE CONTROL TRANSMITTER Battery installation Remote control transmitter operation range 2 Remote control sensor 1 Within approximately 6 m (20 feet) 3 Battery replacement If the remote control transmitter operates only when it is close to the unit, the batteries are weak. Replace all batteries with new ones. Be sure to replace batteries within about two minutes. If it takes longer than two minutes, the codes preset for the remote control transmitter will return to the factory-set. Notes • There should be no large obstacles between the remote control transmitter and the unit. • If the remote control sensor is directly illuminated by strong lighting (especially an inverter type of fluorescent lamp, etc.), it might cause the remote control transmitter not to work correctly. In this case, reposition the unit to avoid direct lighting. Notes • Use only AAA, R03, UM-4 batteries for replacement. • Be sure the battery polarity is correct. (See the illustration inside the battery compartment.) • Remove the batteries if the remote control transmitter will not be used for an extended period of time. • If the batteries have leaked, dispose of them immediately. Avoid touching the leaked material or letting it come into contact with clothing, etc. Clean the battery compartment thoroughly before installing new batteries. 52 05HTR-5140-e/f-6 52 6/22/99, 2:05 PM  English SETUP CODES Presetting the remote control transmitter Perform the presetting procedure for each component you want to control with the remote control transmitter. Note: If your component does not respond to any of the codes listed for the manufacturer, use the original remote control transmitter that was supplied with the component. To control your components (MD recorder, DVD player, TV, etc.) 1. 2. Turn on the component to be used. Press the component selector which matches the component to be controlled (TAPE/MD, DVD/LD, TV etc.). To use a second (and third) VCR You can control a second (and/or third) VCR in the CBL/DBS and DVD MENU modes if a CBL (or DBS) or DVD player is not being used. If you want to control a second (and/or third) VCR in the DVD MENU mode, you must preset the code for an LD player in that mode. 1. 2. 3. Press both VOLUME buttons ( ) for about four seconds at the same time so that the indicator flashes twice. 3. 4. 5. Turn on the VCR to be used. Press CBL/DBS or DVD MENU on the component selector. Use the numeric buttons to enter the four-digit manufacturer’s code for the component to be used. Make sure that the indicator flashes twice. If the indicator does not flash, repeat step 3 and re-enter the code. Press POWER (or any other button) on the remote control transmitter to check if you have preset the code correctly. If the component cannot be controlled by the remote control transmitter, try entering another code for the same manufacturer. Returning to the factory-set codes To return all components to the factoryset codes, follow these steps. 1. Press a button on the component selector other than AMP<TUNER>. 2. Press both VOLUME buttons ( ) for about four seconds at the same time so that the indicator flashes twice. 3. Enter the code number “9990”. 4. Make sure that the indicator flashes twice. To return each component to the factoryset codes, follow these steps. 1. Press the component selector which matches the component to be returned to the factory-set codes. 2. Press both VOLUME buttons ( ) for about four seconds at the same time so that the indicator flashes twice. 3. Enter the code number “0000”. 4. Make sure that the indicator flashes twice. Press both VOLUME buttons ( ) for about four seconds at the same time so that the indicator flashes twice. The following codes are preset by the factory. 4. 5. Use the numeric buttons to enter the four-digit code for the second (or third) VCR. Make sure that the indicator flashes twice. If the indicator does not flash, repeat step 3 and re-enter the code. Press POWER (or any other button) on the remote control transmitter to check if you have preset the code correctly. If the VCR cannot be controlled by the remote control transmitter, try entering another code for the same manufacturer. Factory-set codes Component Component Code selector TV TV 0101 CBL/DBS DBS tuner 0006 VCR VCR 0002 DVD/LD DVD player 0008 YAMAHA CD CD player 0005 YAMAHA TAPE/MD Tape deck 0004 YAMAHA We recommend that you write all code numbers you have preset on the “Quick Reference Card”. 53 05HTR-5140-e/f-6 53 6/22/99, 2:05 PM  TROUBLESHOOTING If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and contact your authorized YAMAHA dealer or service center for help. SYMPTOM REMEDY The unit fails to turn on when STANDBY/ON is pressed, or set in the standby mode suddenly soon after the power has been turned on. The power cord is not plugged in or the plug is not completely inserted. Firmly plug in the power cord. The IMPEDANCE SELECTOR switch on the rear panel is not fully set at the upper or lower end. Slide the switch fully to the upper or lower end. The unit does not work normally. The internal microcomputer has been frozen by an external electric shock (lightning, excessive static electricity, etc.) or by a power supply with low voltage. Set the unit in the standby mode and disconnect the AC power cord from the AC outlet. After about 30 seconds have passed, connect the power cord and operate the unit again. No sound or no picture. Incorrect output cord connections. Connect the cords properly. If the problem persists, the cords may be defective. Appropriate program source has not been selected. Select an appropriate program source by INPUT. SPEAKERS have not been set properly. Set SPEAKERS corresponding to the speakers in use to the ON position. The speaker connections are not secure. Secure the connections. The protection circuit has been activated because of a short circuit, etc. Set the unit in the standby mode and then switch on again to reset the protection circuit. The SLEEP timer has functioned. Cancel the SLEEP timer. Only one side speaker outputs sound. Incorrect setting of BALANCE. Adjust it to the appropriate position. Incorrect cord connections. Connect the cords properly. If the problem persists, the cords may be defective. A “humming” sound can be heard. Incorrect cord connections. Firmly connect the audio plugs. If the problem persists, the cords may be defective. No connection from the turntable to the GND terminal. Make the GND connection between the turntable and this unit. The volume level is low while playing a record. The record is being played on a turntable with an MC cartridge. The turntable should be connected to the unit through the MC head amplifier. The volume level cannot be increased, or the sound is distorted. The component connected to the REC OUT terminals of this unit is in the standby mode. Turn on the power to the component. No sound from the effect speakers. The sound effect is set off. Press EFFECT to turn it on. A Dolby Surround decoding program is being used with material not encoded with Dolby Surround. Use a different sound field program. The sound output level of the rear speakers is set to minimum. Raise the sound output level of the rear speakers. A monaural sound source is being played in the DOLBY PRO LOGIC or DOLBY PRO LOGIC ENHANCED program. Select another sound field program suitable for the monaural sound source. The sound suddenly goes off. Amplifier CAUSE No sound from the rear speakers. 54 05HTR-5140-e/f-7 54 6/22/99, 2:05 PM  FM Amplifier No sound from the center speaker. English SYMPTOM REMEDY CAUSE The input signals of the source encoded with Dolby Digital do not have center channel signals. Refer to the instruction for the source being currently played. The sound output level of the center speaker is set to minimum. Raise the sound output level of the center speaker. The function “CNTR” in the SET MENU is set to the NONE position. Select the LARGE or SMALL position. Incorrect sound field program selection. Select the appropriate program. The sound field cannot be recorded. It is not possible to record the sound field on a tape deck or MD recorder connected to the unit’s REC OUT terminals. The DVD/LD, TV or DBS source cannot be recorded on a tape deck, MD recorder or VCR connected to this unit. The DVD/LD player, TV or DBS tuner is connected to the unit by only the digital terminals. Make additional connections between the analog terminals. FM stereo reception is noisy. The characteristics of FM stereo broadcasts may cause this problem when the transmitter is too far away or the antenna input is poor. Check the antenna connections. Try using a high-quality directional FM antenna. Set TUNING MODE to the manual tuning mode. There is distortion and clear reception cannot be obtained even with a good FM antenna. There is multipath interference. Adjust antenna position to eliminate multipath interference. The desired station cannot be tuned in with the automatic tuning method. The station is too weak. Use the manual tuning method. Use a high-quality directional FM antenna. Previously preset stations can no longer be tuned in. This unit has been unplugged for a long period. Repeat the presetting procedure. The desired station cannot be tuned in with the automatic tuning method. The signal is weak or antenna connections are loose. Tighten the AM loop antenna connections and rotate it for best reception. Remote control transmitter FM/AM AM Use the manual tuning method. There are continuous crackling and hissing noises. Noise will result from lightning, fluorescent lamps, motors, thermostats and other electrical equipment. Use an outdoor antenna and a ground wire. This will help somewhat, but it is difficult to eliminate all noise. There are buzzing and whining noises (especially in the evening). A television set is being used nearby. Relocate this unit away from the TV. <China and General models only> Although you do the operations to recall a preset station, the station cannot be tuned in, or a station other than the preset one is tuned in. Some of the preset station data has been modified because the setting of the FREQUENCY STEP switch was changed after storing the station data. Preset the stations again by following the preset tuning procedure. The remote control transmitter does not work. Direct sunlight or lighting (from an inverter type of fluorescent lamp, etc.) is striking the remote control sensor of the this unit. Change the position of the unit. The manufacturer’s code has not been set properly. Set the code again. The proper manufacturer’s code for the component to be controlled has not been set. Try entering another code for the same manufacturer. The component to be controlled has not been selected. Press the component selector which matches the component to be controlled. 55 05HTR-5140-e/f-7 55 6/22/99, 2:05 PM  Others SYMPTOM CAUSE REMEDY The sound is degraded when listening with the headphones to a CD player or tape deck that is connected to this unit. The unit is in the standby mode. Turn on the power to the unit. There is noise interference from digital or high-frequency equipment or the unit. The unit is too close to the digital or high-frequency equipment. Move the unit further away from those equipment. 56 05HTR-5140-e/f-7 56 6/22/99, 2:05 PM  English SPECIFICATIONS AUDIO SECTION Minimum RMS Output Power 8 ohms, 20 Hz to 20 kHz, 0.04% THD MAIN L/R ........................... 60 W + 60 W CENTER ......................................... 60 W REAR L/R .......................... 60 W + 60 W 8 ohms, 1 kHz, 0.07% THD MAIN L/R ........................... 70 W + 70 W CENTER ......................................... 70 W REAR L/R .......................... 70 W + 70 W Maximum Power [China and General models only] 8 ohms, 1 kHz, 10% THD MAIN L/R ............................. 95 W + 95 W CENTER ........................................... 95 W REAR L/R ............................ 95 W + 95 W Output Level/Impedance REC OUT ..................... 150 mV/1.2 k-ohms SUBWOOFER (MAIN SP: SMALL) ........ 4.0 V/1.2 k-ohms Headphones Jack Rated Output/Impedance CD/TAPE·MD/DVD·LD/TV·DBS/VCR/ VIDEO AUX input, 1 kHz, 150 mV, 8 ohms ...... 0.4 V/390 ohms Frequency Response (20 Hz to 20 kHz) CD/TAPE·MD/DVD·LD/TV·DBS/VCR/ VIDEO AUX to MAIN L/R SP OUT .................................................... 0±0.5 dB RIAA Equalization Deviation PHONO MM .................................. 0±0.5 dB Filter Characteristics MAIN L/R, REAR L/R (SPEAKER: SMALL) (H.P.F) ..................... fc = 90 Hz, 12 dB/oct. SUBWOOFER (L.P.F) ..................... fc = 90 Hz, 18 dB/oct. VIDEO SECTION Video Signal Type [U.S.A. and Canada models] .............. NTSC [Australia and Singapore models] ......... PAL [China and General models] ....... NTSC/PAL Video Signal Level ................ 1 Vp-p/75 ohms Maximum Input Level .......... 1.5 Vp-p or more Signal-to-Noise Ratio ............... 50 dB or more Dynamic Power per Channel (by IHF Dynamic Headroom measuring method) MAIN L/R 8/6/4/2 ohms ................ 80/100/120/145 W Dynamic Headroom (8 ohms) [U.S.A. and Canada models only] ...................................................... 1.55 dB Power Band Width 8 ohms, 30 W, 0.1% THD ......................................... 10 Hz to 50 kHz Damping Factor MAIN L/R 8 ohms, 20 Hz to 20 kHz .......... 60 or more Input Sensitivity/Impedance PHONO MM ................... 2.5 mV/47 k-ohms CD/TAPE·MD/DVD·LD/TV·DBS/VCR/ VIDEO AUX ................... 150 mV/47 k-ohms EXT. DECODER MAIN L/R .................... 150 mV/47 k-ohms CENTER/SURROUND L/R/SUBWOOFER .................................... 150 mV/40 k-ohms Maximum Input Signal PHONO MM 1 kHz, 0.1% THD ............. 100 mV or more CD/TAPE·MD/DVD·LD/TV·DBS/VCR/ VIDEO AUX (EFFECT ON) 1 kHz, 0.5% THD ................. 2.2 V or more Total Harmonic Distortion (20 Hz to 20 kHz) PHONO MM to REC OUT 1 V ........................................ 0.02% or less CD/TAPE·MD/DVD·LD/TV·DBS/VCR/ VIDEO AUX (EFFECT OFF) to MAIN SP OUT 30 W/8 ohms ...................... 0.025% or less Signal-to-Noise Ratio (IHF-A Network) PHONO MM to REC OUT [U.S.A., Canada, China and General models] (5 mV, Input Shorted) .......... 86 dB or more [Australia and Singapore models] (5 mV, Input Shorted) .......... 81 dB or more CD/TAPE·MD/DVD·LD/TV·DBS/VCR/ VIDEO AUX (EFFECT OFF) to MAIN SP OUT (150 mV, Input Shorted) ...... 96 dB or more Residual Noise (IHF-A Network) MAIN L/R SP OUT ................ 150 µV or less Channel Separation (Vol. –30 dB, EFFECT OFF) PHONO MM (Input Shorted, 1 kHz/10 kHz) .................... 60 dB or more/55 dB or more CD/TAPE·MD/DVD·LD/TV·DBS/VCR/ VIDEO AUX (Input 5.1 k-ohms Terminated, 1 kHz/10 kHz) .................... 60 dB or more/45 dB or more Monitor Output Frequency Response .............................. 5 Hz to 10 MHz, –3 dB FM SECTION Tuning Range [U.S.A. and Canada models] ..................................... 87.5 to 107.9 MHz [Australia and Singapore models] ................................. 87.50 to 108.00 MHz [China and General models] 100 kHz step ................ 87.5 to 108.0 MHz 50 kHz step .............. 87.50 to 108.00 MHz 50 dB Quieting Sensitivity (IHF) (100% mod., 1 kHz) Mono ................................. 1.6 µV (15.3 dBf) Stereo ................................ 23 µV (38.5 dBf) Usable Sensitivity (DIN) [Australia and Singapore models only] Mono (S/N 26 dB) ........................... 0.9 µV Stereo (S/N 46 dB) ........................... 28 µV Alternate Channel Selectivity (±400 kHz) [U.S.A., Canada, China and General models only] ....................................... 75 dB Selectivity (two signals, 40 kHz Dev. ±300 kHz) [Australia and Singapore models only] ......................................................... 55 dB Tone Control Characteristics BASS: Boost/cut ............. ±10 dB (50 Hz) Turnover Frequency ......... 350 Hz TREBLE: Boost/cut ........... ±10 dB (20 kHz) Turnover Frequency ........ 3.5 kHz 57 05HTR-5140-e/f-7 57 6/22/99, 2:05 PM  Signal-to-Noise Ratio (IHF) Mono/Stereo [U.S.A., Canada, China and General models] .................................. 81 dB/75 dB (DIN-Weighted, 40 kHz Dev.) Mono/Stereo [Australia and Singapore models] ............................................... 75 dB/69 dB Harmonic Distortion (1 kHz) Mono/Stereo ............................... 0.1%/0.2% Stereo Separation (1 kHz) .................... 48 dB Frequency Response 20 Hz to 15 kHz ................................ 0±1 dB Antenna Input .............. 75 ohms, Unbalanced Output Level [U.S.A., Canada, China and General models] (100% mod., 1 kHz) ...................... 550 mV [Australia and Singapore models] (40 kHz Dev., 1 kHz)] .................... 550 mV AM SECTION Tuning Range [U.S.A. and Canada models] ....................................... 530 to 1,710 kHz [Australia and Singapore models] ....................................... 531 to 1,611 kHz [China and General models] 10 kHz step .................... 530 to 1,710 kHz 9 kHz step ...................... 531 to 1,611 kHz Usable Sensitivity ............................ 300 µV/m Signal-to-Noise Ratio ............................ 52 dB GENERAL Power Supply [U.S.A. and Canada models] ........................................ AC 120 V, 60 Hz [Australia model] ................ AC 240 V, 50 Hz [General model] .............. AC 110/120/220/240 V, 50/60 Hz [China model] .................... AC 220 V, 50 Hz [Singapore model] ............. AC 230 V, 50 Hz Power Consumption [U.S.A., Australia, Singapore, China and General models] ................................ 230 W [Canada model] .................... 260 W/340 VA Maximum Power Consumption 5 ch, 10% THD [General model only] ......................... 630 W AC Outlets 2 SWITCHED OUTLETS [U.S.A., Canada, Singapore, China and General models] ............. 100 W max. total 1 SWITCHED OUTLET [Australia model] .................... 100 W max. Dimensions (W x H x D) .................................. 435 x 151 x 391 mm (17-1/8” x 5-15/16” x 15-3/8”) Weight .............................. 11.2 kg (24 lbs. 11 oz.) Accessories ......................... AM loop antenna Indoor FM antenna Remote control transmitter Batteries Antenna adapter (U.S.A. and Canada models only) Antenna .................................... Loop antenna Output Level (30% mod., 1 kHz) ........................ 150 mV Specifications are subject to change without notice. 58 05HTR-5140-e/f-7 58 6/22/99, 2:05 PM  LIST OF MANUFACTURER’S CODES LISTES DES CODES FABRICANT TV A-Mark 1161 A Tandy 0941 Abex 1151 Admira 1141 Adventura 1131 Aiko 1121 Akai 0331, 1101, 1111 Alba 0431 Alleron 1091 Ambassador 1081 Amstrad 0481, 1081 Anam 0251, 1041, 1051, 1061, 1071 Anam National 1041 AOC 0361, 1021, 1031, 1111, 1161 Archer 1161 Audiosonic 1001 Audiovox 1051, 1161 Awai 1481 Bauer 0441 Baur 1001 Beijing 1511, 1551, 1561 Belcor 1031 Bell & Howell 0981, 0991 Beon 1001 Bradford 1051 Brockwood 1031 Broksonic 1161 Bush 1001 Candle 0351, 0361, 0961, 0971, 1111, 1131 Capehart 1021 Carver 0101 Cathay 1001 Celebrity 0951 Centurion 0411 Changhong 1541, 1551, 1561, 1621 Citizen 0351, 0361, 0921, 0931, 0941, 0961, 0971, 1111, 1121, 1131 Clairtone 1011 Clarivox 1001 Concerto 0351, 0971 Conrowa 1751 Contec 0901, 0911, 1011, 1051 Corando 0941 Craig 0251, 1051 Crown 0941, 1051 Curtis Mathes 0161, 0361, 0931, 0941, 0981, 1111 CXC 1051 Daewoo 0291, 0301, 0331, 0721, 0941, 1001, 1031, 1121, 1191, 1531, 1581, 1591, 1601 Dansai Daytron Decca Dixi Dumont Dynatech Electroband Electrohome Electron Elin Elta Emerson 1001 0941, 1031 0271, 1001 0331, 1001, 1071 0891, 1031 0881 0951, 1011 0941 0941 1001 0331 0001, 0021, 0061, 0071, 0081, 0091, 0111, 0811, 0821, 0831, 0841, 0851, 0861, 0871, 0901, 0921, 0941, 0981, 1011, 1031, 1051, 1081, 1091 Envision 0361, 1111 Erres 1001 Etron 0331 Ferguson 1001 Finlux 1001 Fisher 0171, 0801, 0981 Formenti 0441 Formonti 1001 Fortress 1141 Fujitsu 1091 Funai 1051, 1091, 1341, 1361, 1411, 1451, 1501, 1521 Futuretech 1051 GE 0131, 0161, 0201, 0751, 0761, 0771, 0781, 0791, 0811, 0861, 1041 GEC 0271, 1001 Gemini 0391 Genexxa 0431 Gibralter 0891, 1031, 1111 GoldStar 0031, 0121, 0351, 0411, 0731, 0741, 0861, 0941, 0971, 1001, 1031, 1111, 1151 Goodmans/Tashiko 0271, 0661, 1001 Granada 1001 Grundig 1781, 1791, 1801, 1811, 1821, 1831, 1841, 1851, 1861, 1871, 1881 Gunpy 1051, 1091 H/K 0721 Hallmark 0861 Hanseatic 1001 Harvard 1051, 1061 Hinari 1001, 1091 Hitachi 0181, 0351, 0671, 0681, 0691, 0701, 0711, 0871, 0941, 0971, 1351 Hypson 1001 Ima 1051 Indiana 1001 Infinity Reference 0101 Interfunk 1001 ITT 0611 Janeil 1131 JBL 0101 JCB 0951 Jensen 0311 Jinxing 1531, 1541, 1551, 1561, 1571, 1621, 1631, 1641, 1651, 1691, 1731 JVC 0261, 0281, 0641, 0651, 0661, 0841 Kawasho 0901 Kaypani 1021 Kenwood 0361, 1031, 1111 Kloss 0631, 0721, 1131 KTV 0921, 0941, 1011, 1051, 1111 Leyco 1001 Liesenk & Tter 1001 Lloytron 0941 Loewe 1001 Logik 0991, 1771 Luxman 0351, 0971 Lxi 0101, 0621, 0761, 0861, 0981 Magnavox 0101, 0341, 0391, 0401, 0411, 0421, 0581, 0591, 0601, 0611, 0631, 0661, 0961, 1111 Majestic 0991 Marantz 0101, 0221, 0361, 1001, 1111 Mark 1001 Matsui 0271, 0331, 1001 Mediator 1001 Megatron 0691, 0861, 1161 MEI 1011 M Electronic 1001 Memorex 0331, 0571, 0861, 0971, 0981, 0991, 1771 Metz 1791, 1831, 1891, 1901, 1911, 1921, 1931, 1941 MGA 0361, 0561, 0571, 0861, 1031, 1111 Midland 0751, 0761, 0891, 0941, 1151 Mitsubishi 0221, 0321, 0561, 0571, 0661, 0861, 1031, 1101, 1381 Montgomery 1091 Motorola 1041, 1141 MTC 0351, 0361, 0881, 0931, 0971, 1011, 1031, 1111 Multitech 0881, 1051 NAD 0551, 0621, 0861 NEC 0241, 0351, 0361, 0661, 0971, 1031, 1111, 1321, 1711 113 06HTR-5140-CODE(E/F) 113 6/22/99, 2:07 PM  Neckermann Nei Nikkai Nikko Novabeam NTC Onwa Optimus Optonica Orion Osaki Otto Versand Panasonic 1001 1001 0271, 0431, 1001, 1151 0861, 1111, 1121 0721 1121 1051 0551 0541, 1141 0831, 1001 0271, 1151 1001 0101, 0191, 0251, 0751, 1041, 1311, 1371, 1431 Panda 1541, 1721 Penny 0161, 0361, 0521, 0531, 0621, 0731, 0751, 0761, 0781, 0791, 0861, 0931, 0941, 1031, 1041, 1111, 1151, 1161 Peony 1561, 1621 Philco 0361, 0581, 0591, 0601, 0611, 0631, 0961, 1031, 1111 Philips 0101, 0401, 1001 Phonola 1001 Pilot 0941, 1031, 1111 Pioneer 0511, 0551, 0871, 1331 Portland 0941, 1031, 1121 Priceclub 0931 Prism 0751 Proscan 0761 Protech 1001 Proton 0501, 0861, 0941, 1021, 1161 Pulsar 0891 Pulser 1031 Quasar 0251, 0751, 1041 Quelle 1001 Radio Shack 0541, 0941, 1031, 1051, 1151 Radiola 1001 RCA 0051, 0141, 0151, 0181, 0411, 0491, 0531, 0761, 0771, 0871, 1031 Realistic 0541, 0861, 0941, 0971, 0981, 1031, 1051, 1111, 1151 Rhapsody 1011 R-line 1001 Runco 0891, 1111 Saisho 0331, 1081 Sampo 0361, 0941, 1021, 1111, 1151 Samsung 0331, 0341, 0351, 0361, 0861, 0931, 0941, 0971, 1001, 1031, 1111, 1151, 1461 Samsux 0941 Sanyo 0171, 0231, 0271, 0661, 0801, 0911, 0981, 1231, 1251, 1261 SBR Schneider Scimitsu Scotch Scott 1001 1001 1031 0861 0831, 0861, 0941, 1031, 1051, 1091 Sears 0101, 0161, 0171, 0351, 0481, 0521, 0621, 0761, 0801, 0861, 0971, 0981, 1091 Shanghai 1561, 1681 Sharp 0461, 0471, 0541, 0661, 0911, 0941, 1141, 1241, 1271 Shogun 1031 Signature 0991, 1771 Simpson 0581, 0961 Solavox 1151 Sonoko 1001 Sontec 1001 Sony 0371, 0451, 0661, 0841, 0951, 1281, 1441 Soundesign 0861, 0961, 1051, 1091 Soundwave 1001 Spectricon 1161 Squareview 0481 SSS 1031, 1051 Star-lite 1051 Suprem 0951 Supre-macy 1131 Surpa 0351, 0971 Sylvania 0101, 0361, 0441, 0581, 0591, 0601, 0611, 0631, 0961, 1111 Symphonic 0481 Sysline 1001 Tandy 0271, 0431, 1141 Tatung 0271, 0881, 1001, 1041, 1161 Tcl 1561, 1631, 1701 Technics 0751 Techwood 0351, 0751, 0971 Teknika 0101, 0351, 0571, 0931, 0941, 0961, 0971, 0991, 1031,1051, 1091, 1121, 1131, 1771 Teletech 0331 Tera 0501 Thakral 1671 Thorm 1001 TMK 0351, 0861, 0971, 1081 Toshiba 0381, 0521, 0621, 0661, 0931, 0981, 1301 Tosonic 1011 Totevision 0941 Trical 0911 Universal 0781, 0791 Universum 1001 Vector Research 0361, 1111 Vestel 1001 Victor 0651, 1201, 1211, 1221 Video Concept 1101 Vidikron 0101, 0211 Vidtech 0861, 1031 Viking 1131 Wards 0101, 0361, 0451, 0541, 0581, 0591, 0601, 0611, 0771, 0781, 0791, 0861, 0971, 0991, 1031, 1091, 1111, 1771 Watson 1001 Xogego 1611, 1621, 1661, 1741, 1761 Yamaha 0221, 0361, 0571, 1031, 1111, 1141, 1381 Yoko 1001 Zenith 0011, 0041, 0891, 0991, 1771 Zonda 1161 CABLE ABC Antronix Archer BBT Cabletime Cablevision Colour Voice Comtronics Eagle Comronics Eastern Electricord Electus GE GEC Cable System Hamlin H5 Hamlin H6 Hamlin H6S Hamlin H8 Hamlin H9 Jerrold Jerrold 400L Jerrold 450L Jerrold 550 Jerrold Osd Catv Jerrold Sprucer Magnavox/Philips Mamm Memorex Movie Time Northcoast NSC Oak Oak Sigma 450 Oak Sigma 550 Panasonic TZ 120/130 Panasonic TZ 170/180 Panasonic TZ140 Panasonic TZ150/160 Paragon 114 06HTR-5140-CODE(E/F) 114 6/22/99, 2:07 PM 0256, 0376 0136 0136, 0286 0076 0166 0196 0306, 0346 0216, 0276 0276 0066 0206 0266 0116, 0126 0196 0676 0666 0656 0646 0636 0256 0626 0616 0606 0596 0436 0416, 0426 0296 0386 0146, 0206 0016 0146 0106 0546 0536 0476 0446 0466 0456 0386  Philips 0036, 0216, 0306, 0316, 0326, 0336, 0346 Pioneer 0006, 0086 Pioneer BR50 0846 Pioneer BR60/70/80/81/82 0696 Pioneer BR90 0556 Pulsar 0386 RCA Digital Satellite System 0396, 0406 Realistic 0136 Regency/Eastern 0686 Runco 0386 Samsung 0276 Scientific Atlanta 175/475 0576 Scientific Atlanta 75 0366, 0586 Scientific Atlanta 8650 0566 Signal 0276 SL Marx 0276 Spectavision 0236 Standard Components 0186 Starcom V 0256 Stargate 0276 Sylvania/Texscan 0376, 0496 Teknika 0176 Teleservice 0056 Teleview 0276 Texscan 0186, 0376 TFC 0026 Tocom 0226, 0356 Tocom 5503A 0526 Tocom 5503VIP/5507 0516 Tocom TC56 0506 Toshiba 0386 Tudi 0046 Unika 0136 Universal 0136, 0156, 0206, 0286 Videoway 0096 Viewstar 0216 Zenith 0246, 0386, 0486 DBS TUNER Alpha Star Chaparral Echostar General Instrument HTS Hughes Network Systems Jerrold Panasonic Primestar RCA Sony 0826 0756 0836 0776 0836 0816 0776, 0786 0806 0776, 0786 0766 0796 Hinari Hitachi VCR A Tandy 0902 Adventura 0992 Aiko 0982 Aiwa 0992 Akai 0262, 0942, 0952, 0962, 0972 American High 0932 Amstrad 0992 ASA 0002, 0912 Asha 0922 Audio Dynamics 0202 Audiovox 0912 Beaumark 0922 Bell & Howell 0902 Blaupunkt 0412 Broksonic 0872, 0882, 0892 Bush 0852 Calix 0912 Canon 0862, 0932 CCE 0852, 0982 Citizen 0912, 0982 Colt 0852 Craig 0832, 0842, 0852, 0912, 0922 Curtis Mathes 0662, 0822, 0932 Cybernex 0922 Daewoo 0802, 0812, 0982 DBX 0202 Dynatech 0472, 0992 Electrohome 0912 Electrophonic 0912 Emerex 0792 Emerson 0072, 0132, 0142, 0152, 0162, 0172, 0182, 0192, 0212, 0702, 0712, 0722, 0732, 0742, 0752, 0762, 0772, 0782, 0872, 0882, 0892, 0912, 0952, 0992, 1072 Finlux 0002, 0992 Fisher 0682, 0692, 0842, 0902 Fuji 0672, 0932 Funai 0992 Garrard 0992 GE 0662, 0822, 0932 Go Video 0642, 0652 GoldStar 0082, 0632, 0912 Goodmans 0402 Gradiente 0992 Granda 0612, 0902 Grundig 0002 H/K 1082 Harley Davidson 0992 Harmon/Kardon 0632, 1082 Harwood 0752, 0852 Headquarter 0612 HI-Q 0842 0852 0102, 0562, 0572, 0582, 0592, 0602, 0992 ITT 0942 JVC 0202, 0522, 0532, 0542, 0552 Kenwood 0202, 0542, 0612, 0632, 0902 KLH 0852 Kodak 0912, 0932 Lloyd 0992 Logik 0852 Luxor 0942 LXI 0022, 0912 Magnavox 0002, 0482, 0492, 0502, 0512, 0932 Magnin 0922 Marantz 0002, 0202, 0402, 0632, 0932 Marta 0912 Matsui 0722 Matsushita 0932 MEI 0222, 0932 Memorex 0232, 0242, 0472, 0512, 0612, 0842, 0902, 0912, 0922, 0932, 0992 MGA 0762, 0952 MGA Technology 0922 Minolta 0592, 0602 Mitsubishi 0452, 0462, 0542, 0762, 0952, 1082 Motorola 0472, 0932 MTC 0922, 0992 Multitech 0852, 0992 NAD 0442 NEC 0122, 0202, 0292, 0422, 0432, 0542, 0632 Nikko 0912 Noblex 0922 Olympus 0412, 0932 Optimus 0442, 0472, 0912 Optonica 0402 Orion 0212, 0722, 0742, 0772 Osaki 0912 Panasonic 0012, 0052, 0092, 0222, 0372, 0382, 0392, 0412, 0932 Penny 0202, 0432, 0602, 0632, 0692, 0912, 0922, 0932 Pentax 0592, 0602 Perdio 0992 Philco 0002, 0932 Philips 0002, 0282, 0402, 0492, 0932 Pilot 0912 Pioneer 0442, 0542 Proscan 1002, 1012, 1022, 1032, 1042, 1052, 1062 Pulsar 0512 Quarter 0612 115 06HTR-5140-CODE(E/F) 115 6/22/99, 2:07 PM  Quartz 0272, 0612 Quasar 0382, 0392, 0932 Radio Shack 0912, 0992 Radix 0912 Randex 0912 RCA 0112, 0382, 0392, 0482, 0592, 0602, 0662, 0822, 0942 Realistic 0402, 0472, 0612, 0682, 0842, 0902, 0912, 0922, 0932, 0992 Ricoh 0352, 0362 Saisho 0212, 0582, 0722, 0732, 0742, 0772 Salora 0612, 0762 Samsung 0212, 0312, 0922, 0962 Sanky 0472, 0512 Sansui 0292, 0542, 0832 Sanyo 0242, 0612, 0842, 0902, 0922 SBR 0002, 0282 Schneider 0852 Scott 0342, 0712, 0762, 0872, 0882, 0892 Sears 0302, 0592, 0602, 0612, 0682, 0692, 0842, 0902, 0912, 0932 Sharp 0402, 0472 Shintom 0852 Shogun 0922 Singer 0852 Sony 0032, 0332, 0352, 0362, 0672, 0792, 0932 STS 0602 Sunpak 0352 Sylvania 0002, 0492, 0502, 0762, 0932, 0992 Symphonic 0992 Tandy 0992 Tashiko 0712, 0992 Teac 0992 Technics 0932 Teknika 0322, 0912, 0932, 0992 Telefunken 0252 TMK 0212, 0732, 0772, 0922 Toshiba 0062, 0302, 0342, 0622, 0682, 0712, 0762 Totevision 0912, 0922 Unitech 0922 Vector Research 0202, 0432, 0632 Victor 0532, 0542, 0552 Video Concepts 0202, 0432, 0632, 0952 Wards 0322, 0402, 0472, 0482, 0602, 0712, 0842, 0852, 0922, 0932, 0992 Yamaha 0202, 0632, 0762 Zenith 0042, 0362, 0512, 0672 DVD PLAYER Akai JVC Onkyo Panasonic Philips Pioneer Samsung Sharp Sony Toshiba Yamaha 0108 0168 0128 0048 0188 0208, 0228 0148 0068 0028 0088 0008, 0048 LD PLAYER Aiwa Denon Disco Vision Funai Hitachi (E) Kenwood Magnavox Marantz Mitsubishi NAD Panasonic Philips Pioneer RCA Realistic Sharp Sony Victor Yamaha 0157 0147 0017 0157 0017 0087, 0107 0027 0027 0137 0137 0077, 0177 0027 0037, 0017, 0137 0167 0157 0127 0047, 0057, 0117 0097 0007, 0067 CD PLAYER Acoustic Research 1295 ADC 0025, 0065 Adcom 0205, 0255, 1015 ADS 0265 Aiwa 0295, 0945, 1035, 1055 Akai 0175, 0485, 0535 Alpine 1215, 1305 Audio-Technica 0545 BSR 0245, 0655, 0775 California Audio Lab 0055 Capetronic 1205 Carrera 0245 Carver 0285, 1135 Casio 0345 Crown 0185 Curtis Maths 0345 Denon 0275, 0875, 0885 Deual (E) 0505 Dynamic Bass (H) 0555 Emerson 0205, 0325, 1105 Eroica 1275 Fisher 0095, 0555, 0925, 1005 Garrard 0365 Genexxa 0305, 0325, 1105 GoldStar 1225, 1265, 1135, 1335 H/K 0105, 0175, 0465, 0995 Hitachi 0195, 0505, 0205, 0815 Inkel 0115, 0395 JVC 0315 Kenwood 0045, 0095, 0405, 0585, 0725, 0735, 0745, 0755, 0895 Kyocera 0025 Luxman 0075, 0425, 0675, 0705, 0715, 0985 Magnavox 0165, 0215, 0645, 0955 Marantz 0215, 0235, 0375, 0785, 1345 McIntosh 0355, 1085 MCS 0905, 1315 Memorex 0205, 0225, 0235, 0305, 0325, 1105 MGA 0135 Mission 0215 Mitsubishi 0135, 0445 MTC 1255 NAD 0035, 0615, 0685, 0695 Nakamichi 0125, 0435, 0515 NEC 0255, 0905, 0965 Nikko 0545, 1005 Onkyo 0155, 0455, 0495, 0805, 1155 Optimus 0225, 0245, 0555, 0595, 0845, 0855, 0865, 0895, 0935 Panasonic 0055, 0825, 1095, 1125 Penny 0905 Philips 0165, 0215 Pioneer 0305, 0935, 1045 Proton 0215, 1185 Quasar 0055 RCA 0205, 0915, 1115 Realistic 0205, 0225, 0235, 0325, 0555, 0845 Revox 1175 Rotel 0215 Saba Telecommander (E) 0505 SAE 0215 Samsung 1285 Sansui 0215, 0625, 0975, 1025, 1105 Sanyo 0145, 0555, 0635, 0765 Scott 0325, 1105 Sears 0345 Sharp 0235, 0665, 0895, 1065, 1075 Sherwood 0115, 0235, 0395, 0475 Siements Garrard 1245 Signature 0175 Sontec 1165 116 06HTR-5140-CODE(E/F) 116 6/22/99, 2:07 PM  Sony Staron STS Sylvania Symphnoic Tandy Tangberg Teac 0065, 0565, 0865, 1145 1235 0025 0215 0335 0305 1195 0235, 0335, 0385, 0525, 0795, 0835, 1355 Technics 0055, 0605, 1095 Techwood 1325 Telefunken (E) 0505 Thomson (E) 0505 Toshiba 0035, 0685 Vector Research 0065, 1135 Victor 0315 Wards 0175 Yamaha 0005, 0015, 0575, 1065 MD RECORDER Yamaha 0024 TAPE DECK Aiwa Akai Carver Denon Fisher Garrard JVC Kenwood Magnavox Marantz Mitsubishi Onkyo Optimus Philips Pioneer Revox Sansui Sharp Sherwood Sony Teac Technics Victor Wards Yamaha 0094, 0214, 0224 0184 0094 0304 0144 0194, 0204 0274, 0284, 0294 0124, 0134, 0154, 0234, 0244, 0264 0094 0094, 0344 0184 0364, 0374 0034, 0064, 0204, 0334 0094 0034, 0044, 0064 0354 0094, 0344 0264 0334 0054, 0084, 0324 0194, 0254 0074, 0314 0294 0034 0004, 0014 117 06HTR-5140-CODE(E/F) 117 6/22/99, 2:07 PM  U C AT HTR-5140 HTR-5140 Natural Sound AV Receiver Ampli-Tuner Audio-Video OWNER’S MANUAL MODE D’EMPLOI YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA 05HTR-5140-e/f cv1/4 1 Printed in Malaysia ID V343260 6/22/99, 2:41 PM  Quick Reference Card TAPE/MD AMP<TUNER> POWER TEST CD POWER POWER POWER Input selector Input selector Input selector Input selector EFFECT EFFECT EFFECT DISC SKIP +/– EFFECT DISC SKIP +/– A/B/C/D/E & PRESET +/– MUTE VOLUME TV VOLUME VOLUME SLEEP MUTE SLEEP TV INPUT +/– PRG+/PRG– TIME/LEVEL DVD/LD SET MENU REC/PAUSE PLAY DIR A (TAPE) SKIP– (MD) REWIND (TAPE) SEARCH (MD) VOLUME TV VOLUME DISPLAY (MD) DECK A/B (TAPE) PAUSE (MD) DIR B (TAPE) SKIP+ (MD) STOP FAST FORWARD (TAPE) SEARCH (MD) MUTE SLEEP PLAY VOLUME TV VOLUME DISPLAY SLEEP TV INPUT PAUSE DISPLAY TV INPUT SKIP– STOP STOP SEARCH SEARCH TV VOLUME PAUSE SKIP+ SKIP– SEARCH MUTE SKIP+ PLAY SEARCH V342650  Quick Reference Card DVD MENU VCR POWER CBL/DBS TV VCR POWER CBL/DBS POWER TV POWER CHANNEL CHANNEL CHANNEL Numeric buttons CLEAR +10 DISC SKIP+/– VOLUME MUTE RETURN MENU UP MENU LEFT MENU SELECT TITLE VCR CHANNEL +/– EFFECT CHANNEL ENTER VOLUME TV VOLUME INDEX TV INPUT MUTE TV SLEEP VCR REC (*1) DISPLAY TV INPUT MUTE TV SLEEP VCR PAUSE MENU LEFT VCR PLAY VCR REWIND CHANNEL ENTER VOLUME TV VOLUME MENU RIGHT MENU DOWN MENU +100 CBL/DBS CHANNEL +/– MENU SELECT RECALL *1: Press this button twice to start recording. *1: Appuyer deux fois sur cette touche pour lancer l’enregistrement. *1: Diese Taste zweimal drücken, um die Aufnahme zu starten. *1: Tryck två gånger på den här knappen för att börja spela in på videobandspelaren. EFFECT CHANNEL ENTER VOLUME TV VOLUME TV MUTE TV VOLUME DISPLAY TV SLEEP DISPLAY TV INPUT VCR REC (*1) TV INPUT MENU UP MENU RIGHT VCR STOP VCR FAST FORWARD TV CHANNEL +/– MENU DOWN VCR PAUSE VCR PLAY VCR STOP VCR REWIND VCR FAST FORWARD MENU *1: Premere due volte questo tasto per iniziare la registrazione. *1: Presione dos veces este botón para comenzar a grabar. *1: Druk tweemaal op deze toets om te beginnen met opnemen. V342650