loñapsE /
CONCERT MARIMBA
YM6100
Make sure to read “Precautions for Handling Gas Spring” and “Precautions”.
Lesen Sie unbedingt die „Vorsichtshinweise für die Handhabung der Gasfeder“ und die „Vorsichtsmaßregeln“.
Ne manquez pas de lire les sections « Précautions de manipulation du ressort à gaz » et « Précautions à observer ».
Lea sin falta las “Precauciones para la manipulación del muelle de gas” y las “Precauciones”.
Owner’s Manual
Bedienungsanleitung
Mode d’emploi
Manual de instrucciones
hsilgnE
hsilgnE
/
cstueD / siaçnarF h
/
08.5.9, 1:38 PMPage 1
2
08.5.9, 1:38 PMPage 2
This icon urges you to pay caution (includes dangers and warnings).
This icon indicates actions that are prohibited.
This icon indicates special instructions that should be strictly followed.
Before you use the concert marimba, carefully read the instructions listed below and the owner’s manual.
Cautions when setting the instrument.
Never place the instrument on an sloping, unstable, etc., platform. The instrument may fall or overturn and result in
injury.
Cautions for treatment of the instrument.
Never lean on or climb onto the instrument. The instrument may fall and result in injury.
Do not play or roughhouse around the instrument. Bumping into the instrument may result in injury.
It may also cause instrument may also fall over. Keep children away from the instrument.
If an earthquake occurs, strong shocks caused by the earthquake may overturn the instrument or cause it to move
about. Stay away from the instrument during earthquakes.
Cautions when moving the instrument.
Warning
Disregard of the warnings with this mark or misuse may result in
death or personal injury.
Precautions
Using the Concert Marimba Safely
The concert marimba is a large and heavy instrument that gets used in various places by persons of all ages,
so please obey the following instructions regarding their regular care and placement.
Especially in the case of children, a responsible adult should provide proper instruction on
how to use and treat the marimba before use.
Preventing Injuries —Make sure that all precautions described below are obeyed—
Icons are used in this section to
promote the safe use of this
product, and to prevent you and
others from harm and property
damage. Please fully under-
stand the meaning of the icons
before reading the manual.
About
the
Icons
For example:
Do not disassemble.
Hold the instrument by
the frame end and push
forward slowly.
When moving the instrument on its casters, only move across smooth, flat
surfaces. Hold the instrument by its frame end and push forward slowly.
When moving the instrument on its casters.
1. Avoid moving the instrument across surfaces that are sloped, uneven, or
graveled. The concert marimba can collapse and/or get out of control.
2. Do not run with the instrument. The instrument may become impossible to
stop, crash into a wall, and cause serious injury.
* The YM6100 weighs 106.5kg (234 lbs 12 oz).
Moving the instrument up or down stairs should never be done with the instrument assembled. Doing so is a danger as
parts can fall off, or you can loose balance causing the instrument to fall over. Only move the instrument after it has been
disassembled.
Caution
Injury or handicaps to persons caused by the disregard of warnings with this
mark or, misuse of the instrument, may result in the loss of personal property.
Please change cracked tone bars as soon as possible. Cracked tone bars have sharp edges that can cut hands.
If the instrument is often moved, bolts, parts, etc., may become loose. After moving the instrument, check and make
sure all bolts, parts, etc., are firmly fastened. Firmly tighten all loose items.
Do not use the hammer for anything other than playing the instrument. It may be the cause of injury or accidents. Do not
let children strike other, etc., with the mallet. Do not allow such dangerous behavior to take place.
When assembling, be careful not to pinch your fingers or hands. Take special care when assembling rails and resona-
tor pipes. Two persons should carry out this part of the assembly, double-checking as the assembly proceeds.
3
08.5.9, 1:38 PMPage 3
Please observe the following instructions for proper handling of the gas spring.
Precautions for Handling Gas Spring
2. Instructions for discarding the gas
Make sure to observe the following instructions when discarding the gas spring.
As pressurized nitrogen gas is sealed in the gas spring, be sure to release before discarding it. Or an explo-
sion may occur, causing an injury.
[Precautions]
A. Do not crash.
B. Do not cut.
C. Do not make a hole anywhere other than the
specified positions (q and w in the Fig.1).
D. Do not throw it in the fire.
[Discarding procedure]
1.Put the gas spring in a plastic bag. Using a drill of 2 to 3
mm, make a hole q from outside of the plastic bag at the
position as specified in the figure to release the gas and
oil and then make a hole w at the position as specified.
(Be sure to make holes in the order of q and w. )
2.If a vinyl bag is not used, the oil and drill chips will
spread. (In such a case, wear eye protection glasses. )
* Drill 2 holes as shown above to release the
gas before discarding the gas spring.
Do not apply a high tensile load to the gas spring as it will cause damage to the gas spring.
In the event of a failure, stop using the instrument and contact the shop of its purchase. If your
dealer is unable to assist you, please contact Yamaha directly.
This gas spring requires no oil supply to its sliding
section. Additional oil will reduce the sealing durability
and cause the oil to leak.
Never apply any impact to the gas spring. It will cause
oil leakage, malfunction or breakage.
Never disassemble the gas spring. As a high pres-
sure gas is sealed in it, disassembling it will cause a
high risk.
The gas spring is not rigid enough to prevent bending
due to unbalanced loads, do not attempt to bend it.
A poorly balanced load will cause the rod to bend, re-
sulting in defective operation.
1. Precautions for handling the gas spring
q
w
35mm
15mm
Drill
Plastic bag
Fig. 1
Caution
Danger
Note that a nick in the piston rod or cylinder will
shorten the service life of the seal or result in defec-
tive operation. Do not hit the piston rod or cylinder.
Do not expose the gas spring to an excessively high
or low temperature. The allowable temperature
range for use is -20°C to 50°C.
Avoid using the instrument where it is exposed to to
rain, water or much dust. It will cause malfunction.
Do not apply an excessive force to lift the frame end
and pull off the gas spring from the leg. It will cause
malfunction or breakage.
4
08.5.9, 1:38 PMPage 4
5
08.5.9, 1:38 PMPage 5
6
08.5.9, 1:38 PMPage 6
Cautions
Please read the following instructions carefully before using your marimbas.
Installation Location
Use or storage in the following locations may cause damage,
even when packaged.
• In direct sunlight, such as near a window, or in a closed
vehicle in daytime.
• Near heating devices or in other locations subject to ex-
cessive heat.
• In excessively cold environment.
• In places with excessive humidity or dust.
• Locations subject to vibrations.
Handling
• Never place an object on or lean against the instrument, as
this may cause damage to the tone bars and frame parts or
topple the instrument, which is extremely dangerous.
• Do not use hand orchestra bell mallets or other hard objects
on your marimbas. The resulting dents or scratches in the
tone bars could impair the sound. Also avoid hitting the tone
bars hard with a hard mallet. The tone bars can crack.
Moving and Transporting the Instrument
• Before moving the instrument, make sure that the caster
brakes are released. Also make sure to lift the instrument
slightly when moving over rough surfaces.
• When the instrument must be transported to a different lo-
cation, disassemble it to the same state as when it was
purchased, taking care to pack each component properly.
Disassembly steps are in the opposite order of assembly.
When Not in Use
• Always engage the caster brakes.
Maintenance
• The tone bars should be polished from time to time using a
soft and dry cloth or silicone cloth. Stains that cannot be
removed with a dry cloth may be wiped off using a small
amount of ethyl alcohol. Never use thinner or benzene or a
wet cloth for cleaning purplses.
Keep This Manual for Future Reference
•
After reading, make sure to keep the manual in a safe place.
Assembly Cautions
• When assembling/disassembling the instrument, do
so with at least two persons and follow the instructions
outlined in this manual. Assembly in the wrong order
can cause the pipes to drop which may result in an
injury, impair the performance functionality of the in-
strument or cause noise.
• After final adjustment of the legs the fixing screws
must be tightened securely to prevent loosening.
Looseness may cause the instrument to shift during
performance and can also cause noise and other prob-
lems. Retighten the screws from time to time.
qw
q w
qw
q w
7
Nomenclature
Leg (Small end)
Frame end
(Small end)
Slant shaft
Frame end (Large end)
Caster (with brake)
Caster
Gas spring
Accidental tone bars
Natural tone bars
Leg (Large end)
Rail
Resonators
(Natural tone side)
Resonators
(Accidental tone side)
Resonance regulator
Reinforcement stay
Name Plate
(Model No./Serial No.)
Thank you for purchasing the YAMAHA concert marimba.
We, at YAMAHA, aiming principally at beautiful sounds and playing ease, have made strenuous efforts
in creating the outstanding instruments and selecting high quality materials, and successfully devel-
oped these marimbas. We are convinced that you will enjoy playing your instrument that produces
spreading and yet deep sounds as well as rich volume to your content.
This manual describes proper use of YAMAHA concert marimbas. Please read it thoroughly to ensure
that your instrument will give you enjoyment for a long time.
08.5.9, 1:38 PMPage 7
8
N
K
I
L
K
N
HG
FE
L
I
AB
C
D
J
M
z
Reinforcement stay
(Small end)
Slide guide fixing bolts
Leg (Large end)
Leg (Small end)
Reinforcement stay
(Large end)
Reinforcement stay
(Small end)
Reinforcement stay
(Large end)
Assembly
Slide guide fixing bolts
Slide guide fixing bolts
For safety, the instrument should be as-
sembled by at least two persons in a location
with sufficient space.
We recommend to you to assemble the
instrument on a soft rug or carpet.
z Attach the stay and reinforcement stay to
the left and right sides.
* Before proceeding to the next step, make sure that
the slide guide fixing bolts of the large and small
end legs are securely fastened.
CAUTION
Do not loosen the side guide fixing bolts in this
stage. Loosening them will cause a sudden rise of
the frame end which is very dangerous.
1-1. Each leg and stay joint is marked with a letter.
Align the letters and fully insert the stays into
place, then tighten the wing bolts.
08.5.9, 1:38 PMPage 8
9
Assembly
Reinforcement stay (Large end)
Reinforcement stay
Slant shaft
Reinforcement stay (Large end)
Reinforcement stay (Small end)
Reinforcement stay (Small end)
M
J
Wing bolt
Wing bolt
Reinforcement stay
Leg (Large end)
Slant shaft
Leg (Small end)
Wing nut
Washer
1-2 Connect the slant stays (2 on the large end, 1 on
the small end) to the leg sections.
1-3 Simultaneously connect the stay sections in the
center.
The joint for the square stay is labeled with a “J”
and the joint for the round stay is labeled with an
“M”. Connect both joints at the same time making
sure both are fully inserted, and then tighten the
wing bolts firmly.
Slide the hook on the end of the stay
onto the bolt on the leg section and
secure it firmly in place with the wing
nut and washer.
08.5.9, 1:38 PMPage 9
10
Assembly
Leg (Large end)
Resonator support
x
Reinforcement stay (Large end)
Leg (Large end)
Leg (Small end)
Clamp
B
C
G
F
Frame end (Large end)
Frame end
(Small end)
O
P
1-4. Attach the resonator support to the bass side of
the stay. The ends of the resonator support are
marked with an “O” and a “P”. Attach the support
with the marks facing the proper direction as
shown in the illustration below.
x Lower the inner rails into the frame ends.
2-1. Keeping the inner rail horizontal, lower it onto the
frame ends.
Each frame end is labeled with a character. Make
sure that the labeled ends “B”, “C”, “F”, and “G” are
matched with slots labeled with the same charac-
ter.
08.5.9, 1:38 PMPage 10
11
Clamp
Catcher
Assembly
c
2-2. Remove the clamp from the catcher, lift the clamp
up then align with its receiver on the rail and insert
fully.
c Assemble the resonators.
3-1. Both natural and accidental resonators are divided
into three sections. First, connect the upper and
middle range sections.
NG OK
sound absorption plates
Natural tone bar resonators are fitted with sound ab-
sorption plates. Make sure the resonators are as-
sembled properly.
Firmly fasten the screws from both sides.
* Firmly tighten the screws until they are fully
threaded into the nut.
Resonators (middle range section) Resonators (upper range section)
08.5.9, 1:38 PMPage 11
12
Leg (Large end)
Leg (Small end)
Resonators (Accidental tone side)
Resonators (Natural tone side)
Assembly
3-2 The lower range section resonators are attached
in the same manner. Attach to the already joined
upper and middle range sections.
3-3 Mount both sides of the resonator pipes on the left
and right end frames.
Resonators (Lower range section)
Resonators (Upper & middle range section)
08.5.9, 1:38 PMPage 12
13
Assembly
Resonator Support
Leg (Large end)
O
P
3-4 After attaching the resonators on the natural tone
side and accidental tone side, adjust the angle of
the resonator support so that it supports the natu-
ral tone side (marked with an “O”) at the D18 reso-
nator and the accidental tone side (marked with a
“P”) at the D#19 resonator.
v
Leg (Large end)
Leg (Small end)
A
D
Frame end
(Large end)
H
E
Rail (Performer’s side)
v Mount the outer rails in the same manner as
the inner rails.
The outer rail with the YAMAHA logo attached
should face the audience. The ends of the rail are
marked with a “D” and an “H”.
The ends of the outer rail on the performer’s side are
marked with an “A” and an “E”. Mount the rails so
that the marks are matched ot the slots labeled with
the same character.
Frame end
(Small end)
Reinforcement stay
Resonators (Accidental tone side)
Resonators (Natural tone side)
08.5.9, 1:38 PMPage 13
14
b
Springs
Assembly
Levers
Clamp
b Set the tone bars.
5-1. Set the natural tone bars first.
With one person holding the suspension cord on
the bass side and the other holding the suspension
cord on the treble side securely with both hands,
gently place the tone bars on the rails.
Align each tone bar individually and hook its cord
onto the corresponding post.
5-2. After confirming that the cord is secured to every
post, fix the tone bars by pulling the right and left
cords forward from the large end side and hooking
the two springs into each other.
* When setting the tone bars, use care not to cause
any damage to them.
Attach the clamp to the inner and outer rails and
then hook the levers on the resonator section onto
the clamp.
Guide post
Rail
Lower the long outer rails into place, taking care to
align the metal fittings and guide posts on the un-
derside and sides at the same time.
Frame end
Metal fitting
Bass sideTreble side
08.5.9, 1:38 PMPage 14
15
Assembly
n
q
w
q
n Tuning the Resonators.
The resonators are factory adjusted so that the optimum
resonance level is obtained at 23°C.
If the temperature differs due to playing conditions, the
resonators will require adjustment in order to obtain opti-
mum resonance.
q When the temperature is higher
• As the temperature rises, tone bar pitch lowers and
resonator pitch sharply increases making it neces-
sary to lower the pitch on the resonator to compen-
sate. In this case the resonating section of the tube
should be lengthened, or in other words, the regulator
should be set closer to the open end of the tube.
•Ordinarily, the regulator would be fitted into the pipe
as shown by “A” in the photo on the right, but it can be
reversed as illustrated by “B” in order to obtain maxi-
mum length.
w When the temperature is lower
• In this case the tube’s pitch must be raised. Contrary
to step q above, the resonating section of the tube
should be shortened, or in other words, the regulator
should be set further into the tube.
● Special Considerations
• For performances in large halls, etc., three
people are ideal for carrying out resonator
adjustments; one person to strike the tone
bars, a second to adjust the regulators, and
a third to signal the sound quality while
listening from the audience area.
•
The resonance of B/C and E/F notes should be
double-checked. Sound absorption by the
neighboring note can deteriorate resonance.
• Excessive noise between the cord and tone
bars can be eliminated by slightly loosening
cord tension.
08.5.9, 1:38 PMPage 15
16
Tone Bars Height Adjustment
Always adjust height with two persons, making
sure that both treble and bass sides are parallel.
* An extreme height at one end of the instrument
can damage the instrument.
While supporting the frame end of the leg by hand, loosen
the fixing bolt of the slide guide on both large end and
small end sides.
Adjust the height to the desired level and tighten the fixing
bolts securely.
When adjusting the height, use the lines on the slide guide
for reference and make the tone bars in parallel with the
floor surface.
Assembly
m m Finally, clean all surfaces using a soft, dry
cloth.
Slide guide
08.5.9, 1:38 PMPage 16
CAUTION
17
Specifications
YM6100
YM6100
Range: C16 – C76 (5 octave) (Standard pitch A49=
442Hz)
Bars: Rosewood
Bar sizes: 80 – 41 mm (3.1" – 1.6") wide
25 – 20 mm (1" – 0.8") thick
Resonator: Large round welded tubes/low range (C16–
F33) with resonance regulators
Caster: 100 mm diameter (with brake)
Height Adjustment: Gas spring type
Dimensions (W x D x H): 272 x 116 x 88 – 103 cm
(107.1" x 46" x 34.6" – 40.6”)
Weight: 106.5 kg (234.8 lbs)
* Specifications subject to change without notice.
Scale Range
08.5.9, 1:38 PMPage 17
08.8.8, 5:41 PMPage 68
WP36590 1410 R1 Printed in Japan
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
in andere talen
- English: Yamaha YM-6100 Owner's manual
- italiano: Yamaha YM-6100 Manuale del proprietario
- русский: Yamaha YM-6100 Инструкция по применению
- français: Yamaha YM-6100 Le manuel du propriétaire
- español: Yamaha YM-6100 El manual del propietario
- Deutsch: Yamaha YM-6100 Bedienungsanleitung
- português: Yamaha YM-6100 Manual do proprietário
- dansk: Yamaha YM-6100 Brugervejledning
- suomi: Yamaha YM-6100 Omistajan opas
- čeština: Yamaha YM-6100 Návod k obsluze
- 日本語: Yamaha YM-6100 取扱説明書
- svenska: Yamaha YM-6100 Bruksanvisning
- Türkçe: Yamaha YM-6100 El kitabı
- polski: Yamaha YM-6100 Instrukcja obsługi
- română: Yamaha YM-6100 Manualul proprietarului