Yamaha TF1 Handleiding

Merk: Yamaha

Model: TF1

Categorie: DJ-controllers

Type: Handleiding

Deze handleiding is ook geschikt voor

DIGITAL MIXING CONSOLE

V4.5 Reference Manual

Table of contents

Reference Manual

TF series

Table of contents

Overview ................................................................................... 4

Using this document................................................................................................ 4

The display .............................................................................................................. 4

Universal operations ................................................................. 8

Library screen .......................................................................................................... 8

Keyboard screen .................................................................................................... 10

Menu .................................................................................................................... 10

Button and slider operations .................................................................................. 10

Toolbar.................................................................................... 11

SCENE screen ........................................................................................................ 11

METER screen ........................................................................................................ 14

RECORDER screen (INPUT/OUTPUT/TITLE LIST screen) .......................................... 15

MONITOR screen .................................................................................................. 19

SETUP screen (V3.0 and later)................................................................................ 22

OVERVIEW screen.................................................................... 47

CH STRIP section ................................................................................................... 47

FADER section........................................................................................................ 49

SELECTED CHANNEL section (V4.0 and later) ........................................................ 50

Configuration screens............................................................. 57

INPUT screen......................................................................................................... 57

EQ screen .............................................................................................................. 59

GATE screen .......................................................................................................... 63

COMP screen ........................................................................................................ 65

FX screen (FX1/2, InsFX1–6) .................................................................................. 67

SEND TO AUX screen ............................................................................................ 73

ASSIGN screen....................................................................................................... 74

AUTOMIXER screen (V3.5 and later) ...................................................................... 74

CH VIEW screen..................................................................................................... 76

CH NAME screen ................................................................................................... 84

GEQ screen............................................................................................................ 85

OUTPUT screen ..................................................................................................... 87

SEND FROM screen ............................................................................................... 88

DCA ASSIGN screen............................................................................................... 90

DELAY screen (V2.5 and later)................................................................................ 92

Maintenance screen................................................................. 93

Initialize All Memory screen .................................................................................... 93

Initialize Current Memory screen ............................................................................ 94

Initialize NY64-D screen (V3.0 and later) ................................................................ 94

Input Port Trim screen............................................................................................ 95

Output Port Trim screen......................................................................................... 95

Fader Calibration screen (TF5/TF3/TF1) .................................................................. 96

Channel Color Calibration screen (TF5/TF3/TF1) .................................................... 97

Reference................................................................................. 98

List of parameters saved in Scenes and Presets........................................................ 98

Access limitation parameter list............................................................................. 104

Quick Config Input and input channel relationships ............................................. 106

Warnings and error messages ............................................................................... 108

Index...................................................................................... 110

Product dimensions............................................................... 112

Table of contents

Reference Manual

TF series

Procedures

Recalling a Preset............................................................................................................. 9

Editing a Preset................................................................................................................ 9

Displaying configuration screens ................................................................................... 11

Saving the current settings as a new Scene.................................................................... 12

Recalling a Scene........................................................................................................... 12

Editing a Scene.............................................................................................................. 12

Setting the fade time for a Scene (V4.0 and later).......................................................... 13

Setting the input ........................................................................................................... 16

Setting the output......................................................................................................... 17

Recording...................................................................................................................... 18

Playing back files stored on a USB storage device .......................................................... 19

Checking the input signals ............................................................................................ 20

Setting the oscillator...................................................................................................... 21

Configuring settings in the PREFERENCE screen............................................................. 26

Assigning a feature to a [USER DEFINED KEY] ................................................................ 30

Assigning a feature to a [USER DEFINED KNOB] ............................................................ 31

Assigning a feature to the footswitch............................................................................. 31

Configuring the custom fader bank ............................................................................... 32

Recalling the CUSTOM FADER BANK (TF5/TF3/TF1) ...................................................... 32

Using Recall safe function .............................................................................................. 38

Assigning channels to mute groups ............................................................................... 39

Applying access permissions.......................................................................................... 46

Resetting user settings................................................................................................... 46

Loading user settings to other TF series consoles ........................................................... 46

OVERVIEW screen operations......................................................................................... 54

Copying settings from one channel and applying them to another channel .................. 55

Setting stereo link and the input source......................................................................... 58

Adjusting EQ in manual mode....................................................................................... 61

Adjusting EQ in 1-knob EQ mode .................................................................................. 61

Setting HPF ................................................................................................................... 62

Setting LPF .................................................................................................................... 62

Setting the gate............................................................................................................. 64

Setting the compressor.................................................................................................. 66

Setting an effect ............................................................................................................ 68

Setting an insert effect................................................................................................... 68

Adjusting the SEND TO AUX level.................................................................................. 73

Setting the AUTOMIXER ................................................................................................ 75

Using GEQ..................................................................................................................... 86

Using faders to adjust GEQ (TF5/TF3/TF1) ..................................................................... 86

Adjusting the SEND FROM level .................................................................................... 88

Adjusting the send level from AUX channels, STEREO channels,

and SUB channel to a MATRIX channel (V2.5 and later)..................................... 89

Assigning channels to a DCA group............................................................................... 90

Using the maintenance screen....................................................................................... 93

Calibrating the faders .................................................................................................... 96

If a fader must be calibrated again................................................................................. 96

Adjusting channel colors................................................................................................ 97

Overview

Reference Manual

TF series

Overview

Using this document

You can search for keywords and view reference pages while using this document.

Searching for keywords

You can use the search function of your PDF viewing software to search for the desired text

within the document.

When using Adobe Reader, enter the desired text in the search bar and press your computer's

<Enter> key to begin the search.

Moving backward and forward in your viewing history

When viewing this document using Adobe Reader, you can easily move backward and

forward in your viewing history. This is particularly useful when you click a link to jump to

another page, and then want to return to the original page.

Using the index

An index of the keywords and topics in this document can be found on page 110. You can use

the index to easily jump to the desired explanation or topic.

The display

Here we will introduce the different screens displayed on the TF Series console display.

OVERVIEW screen

This screen is displayed when you first turn on the console.

From here you can move to other screens depending on the operations that you want to

perform.

You can return to the OVERVIEW screen at any time by pressing the Home key ( ).

For the TF5/TF3/TF1, the CH STRIP section is displayed.

For the TF-RACK, the FADER section is displayed. You can switch between the CH STRIP

section and FADER section by pressing the Home key ( ).

For more information about the OVERVIEW screen, see page 47.

Overview

Reference Manual

TF series

Configuration screens

You can touch an area of the OVERVIEW screen to display the configuration screen for the

corresponding area.

1 Toolbar (page 11)

Displays buttons for frequently used features. When you touch a button, the

corresponding configuration screen in the main area of the display.

2 Navigation area

Allows you to select which screen is displayed in the main area of the display.

3 Main area (page 57)

Displays the screen that you select using the toolbar or navigation area.

I Navigation area

Displays the features of the currently selected channel.

You can drag the screen up and down to display other features.

CH1–CH32

1 Displays the INPUT screen. (page 57)

2 Displays the EQ screen. (page 59)

3 Displays the GATE screen. (page 63)

4 Displays the COMP screen. (page 65)

5 Displays the FX1 screen. (page 67)

6 Displays the FX2 screen. (page 67)

7 Displays the SEND TO AUX screen. (page 73)

8 Displays the ASSIGN screen. (page 74)

9 Displays the AUTOMIXER screen (V3.5 and later).

(page 74)

0 Displays the CH VIEW screen. (page 76)

ճղ

NOTE

Only CH1–CH8 are displayed on the AUTOMIXER screen.

Overview

Reference Manual

TF series

CH33–CH40

1 Displays the INPUT screen. (page 57)

2 Displays the EQ screen. (page 59)

3 Displays the FX1 screen. (page 67)

4 Displays the FX2 screen. (page 67)

5 Displays the SEND TO AUX screen. (page 73)

6 Displays the ASSIGN screen. (page 74)

7 Displays the CH VIEW screen. (page 76)

STIN1/2

1 Displays the INPUT screen. (page 57)

2 Displays the EQ screen. (page 59)

3 Displays the DELAY screen. (page 92)

4 Displays the FX1 screen. (page 67)

5 Displays the FX2 screen. (page 67)

6 Displays the SEND TO AUX screen. (page 73)

7 Displays the ASSIGN screen. (page 74)

8 Displays the CH VIEW screen. (page 76)

FX RTN 1/2

1 Displays the SEND FROM screen. (page 88)

2 Displays the FX1 or the FX2 screen. (page 67)

3 Displays the EQ screen. (page 59)

4 Displays the SEND TO AUX screen. (page 73)

5 Displays the ASSIGN screen. (page 74)

6 Displays the CH VIEW screen. (page 76)

AUX1–AUX8

1 Displays the SEND FROM screen. (page 88)

2 Displays the EQ screen. (page 59)

3 Displays the GEQ screen. (page 85)

4 Displays the COMP screen. (page 65)

5 Displays the OUTPUT screen. (page 87)

6 Displays the CH VIEW screen. (page 76)

Overview

Reference Manual

TF series

AUX9/10–AUX19/20

1 Displays the SEND FROM screen. (page 88)

2 Displays the EQ screen. (page 59)

3 Displays the COMP screen. (page 65)

4 Displays the INSFX screen. (page 67)

5 Displays the OUTPUT screen. (page 87)

6 Displays the CH VIEW screen. (page 76)

DCA1–DCA8

1 Displays the DCA ASSIGN screen. (page 90)

2 Displays the CH VIEW screen. (page 76)

STEREO

1 Displays the EQ screen. (page 59)

2 Displays the GEQ screen. (page 85)

3 Displays the COMP screen. (page 65)

4 Displays the OUTPUT screen. (page 87)

5 Displays the CH VIEW screen. (page 76)

SUB

1 Displays the SEND FROM screen. (page 88)

2 Displays the EQ screen. (page 59)

3 Displays the COMP screen. (page 65)

4 Displays the OUTPUT screen. (page 87)

5 Displays the CH VIEW screen. (page 76)

MATRIX1–MATRIX4

1 Displays the SEND FROM screen. (page 88)

2 Displays the EQ screen. (page 59)

3 Displays the DELAY screen. (page 92)

4 Displays the OUTPUT screen. (page 87)

5 Displays the CH VIEW screen. (page 76)

Universal operations

Reference Manual

TF series

Universal operations

In this section we will introduce the screens that are displayed when you press the Library key

( ) and the Menu key ( ), which are found in the Display section of the console's top

panel.

Library screen

Allows you to recall saved Presets.

A Preset is a collection of settings that are customized for a certain type of input, microphone,

instrument, etc. By recalling a Preset, you can set up a channel quickly and easily according

to the type of input, and then fine-tune the settings to your specific needs. You can even save

your own Presets.

1 Channel name

Displays the name of the channel.

2 Category selection button

Allows you to select a category.

Presets that match the selected category are displayed in the Library list.

3 Library selection button

Allows you to switch between the available Libraries. The Presets that are stored in the

selected Library are displayed in the list.

LIBRARY A: Displays the Presets stored in LIBRARY A.

LIBRARY B: Displays the Presets stored in LIBRARY B.

4 List

You can click a header in the list to sort the items by that header. (List items cannot be

sorted by "Information".)

To select a Preset, simply touch it. The selected Preset is highlighted, and can then be

saved, recalled, or edited.

A lock icon is displayed or cleared each time you touch the column. When the icon

is displayed, the Preset is write-protected.

The date on which the Preset was last saved is displayed in the Date column.

5 Recall on/off checkboxes

Allow you to determine which parameters will be recalled (checkbox on) and not be

recalled (checkbox off).

Input channels

HA: Analog/digital gain setting, phantom power on/off, phase setting

Input Select: Input source settings

Name: Channel name, icon, and color

AUX 1–8, STEREO channels

GEQ: GEQ settings

Name: Channel name, icon, and color

FX RTN, AUX9/10–AUX19/20 channels

FX: Effect settings

Name: Channel name, icon, and color

SUB, MATRIX1–4 channels

Name: Channel name, icon, and color

6 Recall CH button

Recalls a Preset to the selected channel.

7 Edit button

Touch this button to display the keyboard so you can edit the title and comment.

(Keyboard screenpage 10)

8 Store button

Saves the settings for the current channel as a Preset. The settings will overwrite the

Preset selected in the Library list.

9 Store As button

Saves the settings for the current channel as a new Preset.

Touch this button to display the keyboard so you can enter the Preset name. (Keyboard

screenpage 10)

0 Preset number (V1.1 and later)

Displays the Preset number. The first number indicates the number of Presets in the

selected category (

2), and the second number indicates the total number of Presets.

ձղ ճ պ

Universal operations

Reference Manual

TF series

Displaying the Library screen from a configuration screen

When you display the Library screen from a configuration screen, one of the following buttons

is added to the Library screen, depending on the configuration screen you were using.

Recall EQ button

Displayed when you enter the Library from the EQ screen, and recalls EQ settings only.

Recall Gate button

Displayed when you enter the Library from the GATE screen, and recalls GATE settings only.

Recall COMP button

Displayed when you enter the Library from the COMP screen, and recalls COMP settings only.

Recall FX button

Displayed when you enter the Library from the FX screen, and recalls FX settings only.

Recall GEQ button

Displayed when you enter the Library from the GEQ screen, and recalls GEQ settings only.

Library screen menu

Press the Menu key ( ) from the Library screen to display the following items.

Recalling a Preset

Touch a Library selection button to select the Library that contains the desired Preset.

A list of Presets is displayed.

You can click a header in the list to sort the items by that header. (List items cannot be sorted by

"Information".)

2. Touch the desired Preset.

The selected Preset is highlighted.

3. Select the items that will be recalled.

Turn the checkboxes on for items that you want to recall.

4. Touch the Recall CH button.

The Preset is recalled to the selected channel.

Preset list

Editing a Preset

1. Recall the desired Preset.

2. Touch the Edit button.

Display the keyboard so you can edit the title and comment.

(Keyboard screenpage 10)

Edit the desired items.

3. touch the Store or Store As button.

Store button: Saves the settings for the current channel as

a Preset. The settings will overwrite the Preset selected in

the Library list.

Store As button: Saves the settings for the current channel

as a new Preset.

1 Copy

Copies the selected Preset.

2 Cut

Cuts the selected Preset.

3 Paste

Pastes the copied or cut Preset to the Library.

4 Delete

Deletes the selected Preset.

Store As

button

Store button

Edit button

Universal operations

Reference Manual

TF series

Keyboard screen

Allows you to edit titles and comments. This screen varies depending on the operation you

are performing.

1 Cancel button

Discards any changes you made and returns to the previous screen.

2 OK button

Saves the changes you made.

3 Title field

Enter the name of the Scene here.

4 Comment field

Enter comments about the Scene here.

5 FadeTime Settings

Specifies fade time settings and switches fade times used in scenes ON/OFF. To display

the FADE TIME screen (page 14), touch the button on the right edge.

6 Keyboard

Touch to enter the desired text.

Displays a menu of options available in the current screen. The content of the menu varies

depending on which screen is being displayed. For information about each menu, refer to the

description for the corresponding page.

Button and slider operations

䐟䐠

䐡䐢

䐣

䐤

Item Term Description

Close button [X] Touch to close the current screen.

OK button Applies the current settings.

Cancel button

Cancels the operation and returns to the previous

screen.

Clear button Clears the information you entered.

Jump icon Displays the relevant screen.

Slider

Flashes in pink when you touch it to indicate it can be

operated.

You can then drag the slider on the display or turn the

[TOUCH AND TURN] knob to adjust the setting.

Pan slider

Flashes in pink when you touch it to indicate it can be

operated by the [TOUCH AND TURN] knob.

Balance slider

Edit icon

Displays the screen where you can edit information,

such as the keyboard screen.

Touch a button with "

M" displayed on it to display the

menu.

Text box

When you touch a text box that can accept values, it

flashes in pink to indicate that its content can be

changed.

Touch the box again to display the screen that allows

you to enter values.

You can also change the value by turning the

[TOUCH AND TURN] knob.

When you touch a text box that can accept text, the

keyboard screen is displayed.

When on (example):

When off (example):

On and off

Switches between on and off when you touch the

item.

Toolbar

Reference Manual

TF series

Toolbar

Provides access to frequently used features and system settings.

The toolbar is displayed regardless of the screen content.

1 Displays the SCENE screen.

2 Displays the METER screen. (page 14)

3 Displays the RECORDER screen. (page 15)

4 Displays the MONITOR screen. (page 19)

5 Displays the SETUP screen. (page 22) (V3.0 and later)

6 Displays the current time. (page 42)

7 Displays the LOGIN screen. (page 44) (V3.0 and later)

The name of the user that is currently logged in is displayed with the icon.

Additionally, the following items may be displayed to indicate the corresponding

status.

ACCESS: The console is accessing the USB storage device that is connected to its

USB connector.

CUE: The cue is turned on.

OSCILLATOR: The oscillator is turned on.

Quick Config: Quick Config is being used. (V2.0 and later)

SCENE screen

Allows you to manage previously saved mixer setups, or "Scenes".

When you recall a Scene, you can exempt certain settings from being replaced by the settings

contained in the Scene; this is called "recall safe".

1 Scene list selection button

Allows you to switch between the available Scene lists.

SCENE A: Displays Scene list A.

SCENE B: Displays Scene list B.

2 Scene list

Displays the Scenes saved in the selected Scene list.

You can click a header in the list to sort the items by that header. (List items cannot be

sorted by "Information".)

To select a Scene, simply touch it. The selected Scene is highlighted, and can then be

saved, recalled, or edited.

A green triangle is displayed next to the Scene that is currently recalled.

A lock icon is displayed or cleared each time you touch the column. When the icon

is displayed, the Scene is write-protected.

The date on which the Scene was last saved is displayed in the Date column.

The Fade Time column (V4.0 and later) displays whether or not the FADE TIME function

is enabled and the time setting.

Displaying configuration screens

When you touch an icon, the corresponding configuration screen is displayed.

To return to the previous screen, touch the icon again, or touch the close button ([X]) in the

upper right of the screen.

ձղճմյնշ

䐟䐠

䐡䐢䐣

Toolbar

Reference Manual

TF series

3 Store button

Saves the current mixer setup and assigns it to the Scene number selected in the Scene

list.

Touch this button to display the keyboard so you can edit the title and comment.

(Keyboard screenpage 10)

4 Recall button

Recalls the Scene that is selected in the Scene list.

5 Edit button

Touch this button to display the keyboard so you can edit the title and comment.

(Keyboard screenpage 10)

Saving the current settings as a new Scene

1. Touch the Scene area of the Toolbar.

2. Touch a Scene list selection button to select the Scene list.

The Scene list is displayed.

3. Touch a blank Scene.

4. Touch the Store button.

Display the keyboard so you can edit the title, comment and fade time (Keyboard screenpage 10).

Enter the new Scene name and a comment.

5. Touch the OK button.

The settings will be saved as a new Scene.

Blank Scene

Recalling a Scene

1. Touch a Scene list selection button to select the

Scene list that contains the desired Scene.

The Scene list is displayed.

2. Touch the desired Scene.

The selected Scene is highlighted.

You can click a header in the list to sort the items by that header. (List items cannot be sorted by

"Information".)

3. Touch the Recall button.

The mixer settings saved in the Scene are recalled.

The name of the recalled Scene is displayed in the upper left

of the screen.

Editing a Scene

1. Select the Scene that you want to edit.

2. Touch the Edit button.

Display the keyboard so you can edit the title, comment and fade time (Keyboard screenpage 10).

Edit the desired items.

3. Touch the OK button.

The settings will overwrite the Scene selected in the Scene list.

Selected Scene

Toolbar

Reference Manual

TF series

SCENE screen menu

Press the Menu key ( ) from the Scene screen to display the following items.

Setting the fade time for a Scene (V4.0 and later)

1. Select the scene for which the fade time is to be set.

2. Touch the Edit button.

The screen will display where you can edit the title, comment and fade time (SOFT KEYBOARD

screen page 10).

3. To turn the fade time on, touch the FadeTime

button. Touch the button once more to turn it off.

4. To set the fade time, touch the Fade Time display

and input the setting using the keyboard.

5. To turn the fade time on and off for each channel,

touch the button on the right edge of the screen.

6. Set each channel on or off using the FADE TIME screen.

7. Touch the OK button.

The fade times will be set for the Scene.

1 Copy

Copies the selected Scene.

2 Cut

Cuts the selected Scene.

3 Paste

Pastes the copied or cut Scene to the Scene list.

4 Delete

Deletes the selected Scene.

NOTE

• If a moving fader is stopped while holding down its corresponding [SEL] key, the fader effect stop at that

position.

• If the same scene is recalled while the fader is moving, the faders for all channels and DCA groups

immediately move to their target positions.

Toolbar

Reference Manual

TF series

FADE TIME screen (V4.0 and later)

On this screen, you can individually turn the channels on and off for which you want to apply

fade time for the Scene.

1 Channel buttons

Use these buttons to individually turn the channels on and off for which you want to

apply fade time. If the channel is colored white, fade time is on.

FADE TIME screen menu

Press the Menu key ( ) on the FADE TIME screen to display the menu icons shown

below.

METER screen

Displays the input and output level of all the channels, and allows you to select the metering

point (i.e., the point at which the level is detected).

1 Input metering point selection menu

Select the input level metering point from the menu.

PRE HPF: After the head amp; before the HPF

PRE FADER: Before the fader

POST ON: After the [ON] key

2 Output metering point selection menu

Select the output level metering point from the menu.

PRE EQ: Before the EQ

PRE FADER: Before the fader

POST ON: After the [ON] key

3 Peak Hold button

Turn this button on to hold the peak level for each level meter. Turn this button off to

remove the peak level that was being held. The Peak Hold on/off setting affects both

input and output channels.

1 All ON

Turns on fade time for all channels.

2 All OFF

Turns off fade time for all channels.

NOTE

You can assign the Peak Hold button to a [USER DEFINED KEY]. (page 27)

ձղճ

Toolbar

Reference Manual

TF series

4 Meters

Display the input and output levels of the channels.

5 Meter display selection button

Allows you to select how many meters are displayed. Three display modes are available.

RECORDER screen (INPUT/OUTPUT/TITLE LIST

screen)

You can connect a USB storage device to the console's iPad connector and use the console

to record audio to the device, play back audio files stored on the device, and manage audio

files stored on the device.

When a USB storage device is connected to the iPad connector, your TF series console can

record its internal signals to the device as an audio file and play back files that are stored on

the device.

You can also connect an iOS device to the console and use your iPad or iPhone as an audio

input source for the mixer.

Recorded files are formatted as 48 kHz, 24-bit stereo WAV files.

Playback is supported for WAV and MP3 (MPEG-1 Audio Layer-3) files.

These features allow you to record signals from the STEREO and AUX buses to the USB

storage device, and use audio files that are saved on your iPad or USB storage device as the

source for the console's ST IN 1 channel.

NOTE

• Simultaneous recording and playback is not supported.

• While recording, the signal being recorded cannot be used as an INPUT channel.

• Compatible USB storage devices must be formatted in FAT32. If necessary, connect the device to the

USB connector (on the right side of the top panel) and use the contextual menu in the SAVE/LOAD

screen to format the device.

• Use only USB storage devices with a sector size of 512 bytes. (Hard drives larger than 2 TB cannot be

used.)

• USB storage devices with an allocation unit size under 4096 bytes are not supported. (This may apply

to small-capacity USB memory devices.)

• For recording, we recommend using a high-speed device, such as a hard disk drive (HDD) or solid-state

drive (SSD). USB memory devices and iOS devices can be used for playback only.

• For playback, MP3 files must be encoded at 44.1 kHz or 48 kHz, with a bit rate of 128 kbps–320 kbps.

Files encoded using variable bit rate (VBR) can be played back, but file length and elapsed playback

time may not be displayed properly.

• To enable operability from TF StageMix, the number of audio files that can be placed in the same folder

is limited to 150 files. If the total number exceeds 150, including the number of folders, then they are not

displayed in the Title list. To use more than 150 files, place them in separate folders (V4.0 and later).

Toolbar

Reference Manual

TF series

INPUT/OUTPUT screen

Allows you to configure inputs and outputs for playback and recording.

1 RECORD source selection menu

Allows you to select the source that will be recorded.

The source selected here is also output to CH33 and CH34 of the USB TO HOST

connector.

With V3.5 and later, you can also select MTRX 1/2 and MTRX 3/4.

2 RECORD level meter

Displays the recording level.

3 RECORD level slider

Adjusts the recording level.

4 RECORD CUE button

Turns the recording source cue on and off.

5 PLAYBACK level meter

Displays the playback level.

6 PLAYBACK level slider

Adjusts the playback level.

7 PLAYBACK CUE button

Turns the playback source cue on and off.

ձղճյն

NOTE

When an iPad or other iOS device is connected, "iOS device is connected. Use transport control on the

device." is displayed, and the playback button is not displayed. Use the corresponding app on the iOS

device to control playback.

Setting the input

1. Touch the RECORD source selection menu and select

the source you want to record.

2. Drag the RECORD level slider and adjust the recording

level.

RECORD level slider

Toolbar

Reference Manual

TF series

TITLE LIST screen

When a USB storage device is connected to the console via the iPad connector, you can use

this screen to play back audio files saved on the device and record the signal from the 2MIX

source to the device.

1 Parent directory button

Displays the directory that is one level above the current directory.

2 Current directory

Displays the path of the current directory on the USB storage device.

3 USB storage device information

Displays the volume name of the USB storage device.

The amount of available space (i.e., available capacity and available percentage of total

capacity) on the USB storage device is also displayed.

4 File list

Displays a list of the files in the current directory.

You can click a header in the list to sort the items by that header.

Touch a file name to select the file for playback or editing.

Touch the music note icon to start and pause playback.

Files whose checkboxes are turned on will be played back-to-back during continuous playback.

The name of each file in the directory is displayed in the File Name column.

Artist information is displayed in the Artist column (MP3 files only) and the length of the

file is displayed in the Time column.

3. If you want to monitor the record source, touch the

RECORD CUE button to turn the cue on.

Setting the output

1. Drag the PLAYBACK level slider and adjust the playback

level.

2. Touch the PLAYBACK CUE button to turn the cue on.

PLAYBACK level slider

ձղ ճ

յնշոչպջռս

Toolbar

Reference Manual

TF series

If the total number exceeds 150, including the number of folders, then the files are not

displayed in the Title list and operations

5 to C cannot be performed.

In that case, the “Recorder supports a maximum of 150 items in a folder. Please remove

some files from this folder to continue.” message is displayed (V4.0 and later).

5 Follow playback button

When this button is turned on during continuous playback, the file that is currently

playing is highlighted in the file list.

6 File information

When playing back an MP3 file, the file's bit rate and the current playback location are

displayed here.

When playing back a WAV file, the file's sample rate and the current playback location

are displayed here.

When recording, the WAV file's sample rate and the elapsed recording time are

displayed here.

7 Playback mode selector button

You can select the desired playback mode.

Touch the button to toggle through the available modes.

: SINGLE playback; the file is played and then playback stops.

: SINGLE REPEAT; the file plays repeatedly until you stop playback.

: ALL; all files with checkboxes turned on in the file list are played back one after

another, and then playback stops.

: ALL REPEAT; all files with checkboxes turned on in the file list are played back one

after another, and then playback repeats until you stop playback.

8 Previous button

Moves the playback location to the beginning of the current file or to the beginning of

the previous file.

9 Stop button

Stops playback and recording.

0 Play/pause button

Starts and pauses playback.

A Next button

Moves the playback location to the beginning of the next file.

B Record button

Sets the console to record-ready mode. If the number of audio files in a folder, including

the number of folders, exceeds 150, then the Record button is disabled.

C File name edit button

Allows you to edit the file's name.

NOTE

When an iPad or other iOS device is connected, "iOS device is connected. Use transport control on the

device." is displayed, and the playback button is not displayed. Use the corresponding app on the iOS

device to control playback.

Recording

1. Connect a compatible USB storage device to the iPad connector.

2. Touch the record button.

The record button begins flashing to indicate that the console is in record-ready mode.

3. When you're ready to start recording, touch the play/pause button.

The record button remains lit during recording.

You can touch the play/pause button to pause and resume recording.

4. When you're ready to stop recording, touch the stop button.

The recorded file is named automatically based on the console's date and time setting.

5. If necessary, touch the file name edit button and change the file name.

Toolbar

Reference Manual

TF series

RECORDER screen menu

Press the Menu key ( ) from the RECORDER screen to display the following items.

MONITOR screen

Allows you to manage cue and monitor signals and to control oscillators.

The CUE/MONITOR screen is used to control the signals that are monitored using

headphones and near-field monitors. Here you can select the sources that will be

continuously monitored, and select individual channels for monitoring using the CUE feature.

The OSCILLATOR screen is used to configure the oscillator and turn it on and off. The console

has a built-in oscillator that can output a sine wave or pink noise to the desired bus, allowing

you to check external devices or test the characteristics of a venue.

CUE/MONITOR screen

Allows you to monitor certain inputs using headphones or speakers. You can select which

sources will be monitored, change the monitor signal to mono, or add a delay.

1 CUE point selection buttons

Selects the point in the signal path that will be monitored.

PFL: Before the fader

AFL: After the fader (inputs are PFL only)

2 CUE mode button

Used to select the CUE mode.

Mix CUE: Enables cue for multiple channels.

Last CUE: Enables cue for the last channel selected.

Playing back files stored on a USB storage device

1. Touch the file that you want to play in the file list.

To play a file stored in a different directory, touch the parent directory button and navigate to the

desired directory.

2. Touch the playback mode selector button and

select the desired mode.

3. Touch the play button.

Playback begins.

1 Make Dir

Makes a new directory in the current directory. If

the number of audio files in a folder, including the

number of folders, exceeds 150, then the Make Dir

function is disabled.

2 Delete

Deletes the selected file.

Selected fileParent directory button

Play button

Playback mode selector button

ձղճմյն

պջ

Toolbar

Reference Manual

TF series

3 PFL Trim setting text box (V3.5 and later)

Adjusts the CUE monitor volume when PFL is selected. This can be set within a range of

-30 dB to +20 dB. Touch to display the input screen for each value. (page 10)

4 Mono button

Allows you to change the monitor signal to mono.

5 Delay button

Delays the monitor signal.

6 Monitor output button

Turns the monitor output on and off.

The signal is output from the [PHONES] jack regardless of this setting.

7 Monitor level meter

Displays the monitor level.

8 Monitor level slider

Adjusts the monitor output level.

The signal is output from the [PHONES] jack regardless of this setting.

9 Clear CUE button

Cancels all cue selections.

0 Delay setting

Delay can be specified in frames (V3.5 and later), meters, feet, or ms (milliseconds).

Touch a text box to display the keyboard and enter a value. (page 10)

A Monitor selection buttons

Allow you to select the sources that will be monitored.

TF5/TF3/TF1

TF-RACK

Checking the input signals

1. Touch a CUE mode button to select

the desired cue mode.

2. Select the desired monitor sources by

touching the corresponding monitor

selection buttons.

3. Select the desired cue point by

touching the corresponding CUE

point selection button.

4. Touch the PFL Trim setting text box to

set the CUE monitor volume.

5. Touch the monitor output button to

turn the monitor output on and off.

6. Drag the monitor level slider to adjust

the monitor level.

7. Select the desired delay time.

Touch one of the delay setting text boxes to

display the keyboard. This can be specified in

frames, meters, feet or ms (milliseconds). The

frame rate can be set in the Others section of

the PREFERENCE screen. (page 26)

8. Touch the delay button.

The delay is turned on.

Monitor level

slider

Delay button

Delay setting

Tex t b oxe s

Toolbar

Reference Manual

TF series

OSCILLATOR screen

Allows you to configure the oscillator.

1 Oscillator mode button

Allows you to select the oscillator mode.

SINE WAVE: A sine wave will be output continuously.

PINK NOISE: Pink noise will be output continuously.

BURST NOISE: Pink noise will be output intermittently.

2 Parameter sliders

Allows you to adjust parameters for the oscillator.

When the oscillator mode is set to SINE WAVE, this setting determines the frequency of

the sine wave.

When the oscillator mode is set to BURST NOISE, this setting determines the Width

(duration of the noise) and Interval (length of silence between noise bursts).

When the oscillator mode is set to PINK NOISE, nothing is displayed here.

3 Oscillator output button

Turns the oscillator output on and off. When the oscillator is turned on, the oscillator

signal is sent to the input channels that are selected by the oscillator assignment

buttons.

4 Oscillator output level slider

Adjusts the oscillator output level.

5 Oscillator output meter

Displays the oscillator output level.

6 Oscillator assignment buttons

Determine which channels the oscillator is sent to. You can select multiple channels.

ձղճ

յն

Setting the oscillator

1. Touch the oscillator mode button and select the desired

mode.

2. Use the oscillator assignment buttons to determine

which channels the oscillator signal will be sent to.

3. Touch the oscillator output button to turn on

the oscillator output.

4. While referring to the oscillator output level

meter, drag the oscillator level slider to adjust

the oscillator output level.

When the oscillator mode is set to SINE WAVE, you can

also adjust the frequency of the oscillator.

When the oscillator mode is set to BURST NOISE, you

can also adjust Width (duration of each noise burst) and

the Interval (duration of each silence between noise

bursts).

Channel is selected

Oscillator

output button

Oscillator

level slider

Oscillator

output meter

Toolbar

Reference Manual

TF series

SETUP screen (V3.0 and later)

Allows you to configure general mixer settings, as well as settings for OMNI OUT, Recall Safe,

[USER DEFINED KEYS], [USER DEFINED KNOBS], custom fader banks, and other

preferences.

1 Save/Load icon (page 23)

Displays the SAVE/LOAD screen.

2 Preference icon (page 25)

Displays the PREFERENCE screen.

3 User Defined Control icon (page 27)

Displays the USER DEFINED CONTROLS screen.

4 Custom Fader Bank icon (page 32)

Displays the CUSTOM FADER BANK screen.

5 Bus Setup icon (page 33)

Displays the BUS SETUP screen.

6 OMNI OUT icon (page 34)

Displays the OMNI OUT screen.

7 Slot Setup icon (V2.0 and later) (page 34)

Displays the SLOT SETUP screen.

8 Recall Safe icon (page 38)

Displays the RECALL SAFE screen.

9 Mute Group icon (V4.0 and later) (page 39)

Displays the MUTE GROUP ASSIGN screen.

0 +48V Master button

Master button that turns the console's phantom power feature on and off. When this

button is turned off, phantom power will not be supplied to any channels, even if their

+48V buttons are turned on. (page 57)

A Brightness icon (page 40)

Displays the BRIGHTNESS screen.

B Network icon (page 41)

Displays the NETWORK screen.

C Time icon (page 42)

Displays the TIME screen.

D Log icon (page 42)

Displays the LOG screen.

E Help icon (page 43)

Displays the HELP screen.

F About icon (page 43)

Displays the ABOUT screen.

ձղ յն

շչ

ջրտվսռ

Toolbar

Reference Manual

TF series

SAVE/LOAD screen

Displays a list of saved directories and files.

1 Parent directory button

Displays the directory that is one level above the current directory.

This button is grayed out if the current directory is the top directory.

2 Current directory

Displays the name of the current directory.

3 Volume name

Displays the volume name of the USB storage device and the amount of available space.

4 File list

Displays a list of the directories and files stored on the USB storage device. When an item

in the file list is selected, it is highlighted to indicate it will be the subject of any

subsequent operations.

You can touch a header in the list to sort the items by that header. Touch the same

header again to switch between ascending and descending order.

File Name: Displays directory and file names. An icon is displayed for each item so that

you can distinguish between the two.

Comment: Displays any comments you have entered for TF Series console files. To edit

a file's comment, select the file and then touch the Edit button to display the

keyboard (page 10).

Date: Displays each item's modified date.

5 Edit button

Allows you to edit the selected file's file name and comment.

6 Load button

Loads the file selected in the file list.

The LOAD SELECT screen is displayed when you press the Load button. (V2.0 and later)

7 Save button

Saves the current settings by overwriting them over the file selected in the file list.

8 Save As button

Saves the current settings by saving them as a new file.

SAVE/LOAD screen menu

Touch the Menu key ( ) from the SAVE/LOAD screen to display the following items.

ձղ ճ

յնշո

1 Copy

Copies the selected file.

2 Paste

Pastes the file into the current directory.

3 Make Dir

Creates a new directory.

4 Delete

Deletes the selected file.

5 Format

Formats the USB storage device that is connected

to the console.

Toolbar

Reference Manual

TF series

LOAD SELECT screen (V2.0 and later)

Allows you to select which data is loaded when you load a TF Series setup file.

1 All/Custom selection button

Allows you to select the type of data that will be loaded. When All is selected, all data

will be loaded.

When Custom is selected, the checkboxes on this screen can be used to select the data

that will be loaded.

2 Data selection checkboxes

Turn on the checkboxes according to the type of data that you want to load.

The User Account checkbox is displayed for both All and Custom, but you can change

the checkbox setting only when you are logged in as the Administrator.

3 Load button

Touch this button to load the data.

4 Override Protected Scenes & Libraries checkbox

When this checkbox is turned on, protected Scenes and Libraries will also be overwritten

by loaded data. If you want to prevent protected Scenes and Libraries from being

overwritten, turn off this checkbox.

Data that can be saved and loaded

The following data can be saved and loaded on the SAVE/LOAD screen.

ճմ

Data that is saved/loaded Description

Scene Memory All Scenes and the current Scene

Channel Library All channel Presets

+48V Master

Mute Safe

Mute Master

Cue Except channel cue settings

Oscillator Except oscillator on

Monitor

Meter

Recall Safe

User Defined Keys

User Defined Knobs

Foot Switch

Custom Fader Bank

Preference

Except the following settings: Help Language, Show Help at Startup, Touch

Area Optimization, [Home] Key

Slot Setup Quick Config, HA Control

User Account Only when logged in as Administrator

Data that is not saved/loaded Description

Cue Channel cue settings

Oscillator Oscillator on

Brightness

Preference

Help Language, Show Help at Startup, Touch Area Optimization settings,

[Home] Key

Date Time

Network

Console Lock

Input Port Trim

Output Port Trim

Fader Calibration

Channel Color Calibration

Toolbar

Reference Manual

TF series

PREFERENCE screen

Allows you to configure general operating settings regarding confirmation message display,

[SEL] key behavior, etc.

1 Auto CH Select section

INPUT/OUTPUT: When turned on, a channel of the corresponding type will be selected

automatically when you operate that channel's fader.

You can turn this feature on and off independently for input channels

and output channels.

[CUE] > [SEL] Link: When turned on, a channel will be selected when you turn its CUE

on.

[SEND SEL] > [CUE] Link (V4.0 and later): Specifies whether or not to link channel

selection to a cue in the SENDS ON FADER

mode.

Memorize [SEL] Position for Each FADER BANK: Determines whether channel

positions are remembered in fader

banks.

2 Confirmation section

Store/Recall: When turned on, a confirmation message is displayed when you store and

recall features.

INPUT Select/OUTPUT Patch: When turned on, a confirmation message is displayed

when you change the input selection or OMNI OUT

patching.

3 Help section

Help Language: Determines the language used when displaying the HELP screen.

Show Help at Startup: Determines whether the HELP screen is displayed automatically

after the console starts up.

Toolbar

Reference Manual

TF series

4 Key Function section (V4.0 and later)

[TAP] Key Blink (V2.0 and later): Switches the flashing [TAP] key on or off. Tapped

tempos can be input even when the key is off.

[Home] Key (V4.0 and later): Displayed when the [Home] key is touched on the top

panel. Selects the section on the OVERVIEW screen. Each

touch of the [Home] key successively displays the next

section that is switched on.

5 Others section

Touch Sensing Area Optimization: Allows you to optimize the touchscreen's

sensitivity.

Stand: Optimized for operating the touchscreen

when you are positioned above it, such as

when standing.

Sit: Optimized for operating the touchscreen

when you are positioned below it, such as

when sitting.

Display Delay Scale (V2.5 and later): You can select the desired units (frames, meters,

feet, milliseconds) that are displayed in the

DELAY box for MATRIX and ST IN channels.

Frame Rate (V3.5 and later): Selects the frame rate (in numbers of frames) for the

delay setting.

RTA Offset (V3.6 and later): Adjusts the RTA sensitivity of the EQ and GEQ screens.

When this is touched, a screen for inputting numerical

values will appear.

USB 1/2 Output(V4.5 and later): Selects the signals to be output to channels 1 and 2

of the USB TO HOST connector.

Ch 1/2 Direct is the output before the fader, and ST

L/R, AUX, and MTRX are the outputs after the fader.

Configuring settings in the PREFERENCE screen

1. Use the buttons on the PREFERENCE screen to configure the settings as desired.

2. When finished, touch the close button ([X]).

Toolbar

Reference Manual

TF series

USER DEFINED CONTROLS screen

This screen allows you to assign features to the [USER DEFINED KEYS], [USER DEFINED

KNOBS], and to the footswitch.

1 Keys button

Allows you to assign features to the [USER DEFINED KEYS] on the top panel.

2 Key setup buttons (A–F)

Touch the desired button to display the screen that allows you to assign features to the

corresponding key.

Features that can be assigned to [USER DEFINED KEYS]

FUNCTION PARAMETER1 PARAMETER2

Description

No Assign No feature is assigned

Automixer

Bypass Group a, Group b Bypasses the group assigned to PARAMETER 2.

Specific CH CH 1–8

Turns the Automixer on and off for the

channel assigned to PARAMETER 2.

Brightness Bank Change

Switches the brightness setting bank. This

feature is supported from V1.1.

CH ON Specific CH

CH 1–40,

ST IN 1, ST IN 2,

FX 1, FX 2,

DCA 1–8,

AUX 1–8,

AUX 9/10–19/20,

STEREO, SUB,

MATRIX1–4 (V2.5 and later)

Turns the channel assigned to PARAMETER 2

on and off.

ձճյղ

CH Select

Inc

Select channels in order of the direction

selected for PARAMETER 1.

Dec

Specific CH

CH 1–40,

ST IN 1L–ST IN 2R,

FX1L–FX2R,

AUX 1–8,

AUX 9–20,

STEREO L, STEREO R,

SUB,

MATRIX1–4 (V2.5 and later)

Selects the channel assigned to PARAMETER 2.

CUE Specific CH

CH 1–40,

ST IN 1, ST IN 2,

FX 1, FX 2,

DCA 1–8,

AUX 1–8,

AUX 9/10–19/20,

STEREO, SUB,

MATRIX1–4 (V2.5 and later)

Turns the cue on and off for the channel

assigned to PARAMETER 2.

Effect Bypass

FX 1, FX 2,

INS FX 1–6

Bypasses the effect assigned to PARAMETER 2.

EQ Band Select

HPF, LPF, Low, Low-Mid,

High-Mid, High

Selects the band assigned to PARAMETER 2.

(V3.0 and later)

Help Displays help information.

Meter Peak Hold ON Turns the peak hold on and off.

Monitor

Output Turns the monitor out on and off.

Source Select

STEREO, SUB,

STIN 1, STIN 2,

STIN (TF-RACK),

USB 33/34,

Playback

Selects the monitor source assigned to

PARAMETER 2.

Mute Master

MUTE GROUP 3–

MUTE GROUP 6

Turns the mute on and off for the MUTE

GROUP assigned to PARAMETER 1.

Oscillator

Oscillator On Turns the oscillator on and off.

Specific CH

AUX 1–20,

STEREO L, STEREO R,

SUB

Turns the oscillator sent to the channel

assigned to PARAMETER 2 on and off.

Page Change

Bookmark

Press and hold for more than 2 seconds to

bookmark the current screen. Press and hold

for less than two seconds to display the

bookmarked screen.

Bookmark with

“SEL”

The selected channel is saved with the

bookmark. Same as above.

Close Popup Closes the popup screen.

FUNCTION PARAMETER1 PARAMETER2

Description

Toolbar

Reference Manual

TF series

3 Knobs button

Allows you to assign features to the [USER DEFINED KNOBS].

4 Knob setup buttons

Touch the desired button to display the screen that allows you to assign features to the

corresponding [USER DEFINED KNOBS].

Features that can be assigned to [USER DEFINIED KNOBS]

Recorder Transport

Play/Pause

Same as the Play/Pause button on the

RECORDER screen.

Stop

Same as the Stop button on the RECORDER

screen.

Same as the Next button on the RECORDER

screen.

Same as the Previous button on the

RECORDER screen.

Rec

Same as the Rec button on the RECORDER

screen.

Auto Rec

Recording stops and the file is saved, and then

recording resumes immediately as a new file.

Rec & Start

Recording starts immediately without entering

record-ready mode.

SCENE

Inc Selects the next numbered Scene.

Dec Selects the previous numbered Scene.

Store

Assigns the current settings to selected Scene

number.

Recall Recalls the selected numbered Scene.

Inc Recall Recalls the next numbered Scene.

Dec Recall Recalls the previous numbered Scene.

Direct Recall/

Store

A00–99,

B00–99

Recalls the Scene number assigned to

PARAMETER 2. Press and hold for more than

two seconds to assign the current settings to

that Scene number.

FUNCTION PARAMETER1 PARAMETER2

Description

Knob setup buttons

Features Description

No Assign No feature is assigned

Brightness

CH Name Adjusts the brightness of the CH NAME. (TF5/TF3/TF1 only)

CH Color Adjusts the brightness of the CH COLOR indicator. (TF5/TF3/TF1 only)

Screen Adjusts the brightness of the touchscreen.

Panel Adjusts the brightness of the panel LEDs.

CH Level Specific CH

Adjusts the level of the channel assigned to PARAMETER 2. (V3.0 and

later)

CH Select Inc/Dec Selects the channel. (V3.0 and later)

Monitor Level Adjusts monitor level.

Selected CH

Automixer Weight

AUTOMIXER Weight operations for the selected channel (V3.5 and

later)

CH Level Adjusts the level of the selected channel. (V3.0 and later)

Comp 1-knob/Thr

Adjusts 1-knob or threshold for the selected channel's COMP.

When 1-knob COMP is turned on, adjusts 1-knob; when 1-knob COMP

is turned off, adjusts threshold.

Digital Gain Adjusts the DIGITAL GAIN of the selected channel. (V3.0 and later)

EQ 1-knob/Gain

Adjusts 1-knob or gain for the selected channel's EQ.

When 1-knob EQ is turned on, adjusts 1-knob; when 1-knob EQ is

turned off, adjusts gain.

EQ Band Select Selects the band for the selected channel. (V3.0 and later)

EQ Frequency Adjusts EQ frequency for the selected channel.

EQ Q Adjusts EQ Q for the selected channel.

Gate Threshold Adjusts gate threshold for the selected channel.

HPF

Adjusts HPF for the selected channel.

Turn the knob to adjust the frequency.

Input Gain

Adjusts analog gain or digital gain for the selected channel.

When the channel's input is an analog source, adjusts analog gain.

When the channel's input is a digital source (i.e., USB, iPad, or STIN),

adjusts digital gain.

Send Level

Adjusts the send level to the bus selected for PARAMETER2 (FX, AUX,

SUB) for the selected channel. (V3.0 and later)

Pan/BAL Adjusts pan or balance for the selected channel.

RTA Offset Adjusts RTA Offset. (V3.6 and later)

Toolbar

Reference Manual

TF series

5 Foot Switch button

Allows you to assign features to the footswitch.

6 Foot Switch setup button

Displays the features that can be assigned to the footswitch.

Features that can be assigned to the footswitch

FUNCTION PARAMETER1 PARAMETER2

Description

No Assign No feature is assigned

Automixer

Bypass Group a, Group b

Bypasses the group assigned to PARAMETER

Specific CH CH 1–8

Turns the Automixer on and off for the

channel assigned to PARAMETER 2.

Brightness Bank Change

Switches the brightness setting bank. This

feature is supported from V1.1.

CH ON Specific CH

CH 1–40,

ST IN 1, ST IN 2,

FX 1, FX 2,

DCA 1–8,

AUX 1–8,

AUX 9/10–19/20,

STEREO, SUB,

MATRIX1–4 (V2.5 and later)

Turns the channel assigned to PARAMETER 2

on and off.

CH Select

Inc

Select channels in order of the direction

selected for PARAMETER 1.

Dec

Specific CH

CH 1–40,

ST IN 1L–ST IN 2R,

FX1L–FX2R,

AUX 1–8,

AUX 9–20,

STEREO L, STEREO R,

SUB,

MATRIX1–4 (V2.5 and later)

Selects the channel assigned to

PARAMETER 2.

Foot Switch setup button

Clear CUE Clear CUE

Clears all cue selections.

Same as the CLEAR CUE key on the top panel.

CUE Specific CH

CH 1–40,

ST IN 1, ST IN 2,

FX 1, FX 2,

DCA 1–8,

AUX 1–8,

AUX 9/10–19/20,

STEREO, SUB,

MATRIX1–4 (V2.5 and later)

Turns the cue on and off for the channel

assigned to PARAMETER 2.

Effect Bypass

FX 1, FX 2,

INS FX 1–6

Bypasses the effect assigned to PARAMETER 2.

EQ Band Select

HPF, LPF, Low, Low-Mid,

High-Mid, High

Selects the band assigned to PARAMETER 2.

(V3.0 and later)

Help Displays help information.

Meter Peak Hold ON Turns the peak hold on and off.

Monitor

Output Turns the monitor out on and off.

Source Select

STEREO, SUB,

ST IN 1, ST IN 2,

STIN (TF-RACK),

USB 33/34,

Playback

Selects the monitor source assigned to

PARAMETER 2.

Mute Master

MUTE 1 (INPUT),

MUTE 2 (FX),

MUTE GROUP 3–

MUTE GROUP 6

Turns the mute on and off for the channel or

the MUTE GROUP assigned to PARAMETER 1.

Oscillator

Oscillator On Turns the oscillator on and off.

Specific CH

AUX 1–20,

STEREO L, STEREO R,

SUB

Turns the oscillator sent to the channel

assigned to PARAMETER 2 on and off.

Page Change

Bookmark

Press and hold for more than 2 seconds to

bookmark the current screen. Press and hold

for less than two seconds to display the

bookmarked screen.

Bookmark with

“SEL”

The selected channel is saved with the

bookmark. Same as above.

Close Popup Closes the popup screen.

Recorder Transport

Play/Pause

Same as the Play/Pause button on the

RECORDER screen.

Stop

Same as the Stop button on the RECORDER

screen.

Same as the Next button on the RECORDER

screen.

Same as the Previous button on the

RECORDER screen.

Rec

Same as the Rec button on the RECORDER

screen.

Auto Rec

Recording stops and the file is saved, and

then recording resumes immediately as a new

file.

Rec & Start

Recording starts immediately without

entering record-ready mode.

FUNCTION PARAMETER1 PARAMETER2

Description

Toolbar

Reference Manual

TF series

Feature assignment screen

When you select a Function, the items available for Parameter 1 are displayed. Likewise,

when you select an item for Parameter 1, the items available for Parameter 2 are

displayed. Some Functions may not have items available for Parameter 1; some

Parameter 1 items may not have items available for Parameter 2.

SCENE

Inc Selects the next numbered Scene.

Dec Selects the previous numbered Scene.

Store

Assigns the current settings to selected Scene

number.

Recall Recalls the selected numbered Scene.

Inc Recall Recalls the next numbered Scene.

Dec Recall Recalls the previous numbered Scene.

Direct Recall/

Store

A00–99,

B00–99

Recalls the Scene number assigned to

PARAMETER 2. Press and hold for more than

two seconds to assign the current settings to

that Scene number.

TAP TEMPO Same as the TAP key on the top panel.

FUNCTION PARAMETER1 PARAMETER2

Description

Assigning a feature to a [USER DEFINED KEY]

1. Touch the Keys button.

The screen where you can select the

desired [USER DEFINED KEY] is displayed.

Buttons A–F correspond to [USER

DEFINED KEYS] A–F.

2. Touch the Key button that corresponds to the [USER DEFINED KEY] that you want

to configure.

The configuration screen is displayed.

3. Scroll through the Function list and select the desired feature.

4. Scroll through the Parameter 1 list and select the desired item.

If items are available in the Parameter 2 list, select the desired item.

5. Touch the OK button.

Toolbar

Reference Manual

TF series

Assigning a feature to a [USER DEFINED KNOB]

1. Touch the Knobs button.

The screen where you can select the

desired [USER DEFINED KNOB] is

displayed.

Buttons A–D correspond to [USER DEFINED KNOBS] A–D.

2. Touch the Knob button that corresponds to the [USER DEFINED KNOB] that you

want to configure.

The configuration screen is displayed.

3. Scroll through the Function list and select the desired feature.

4. Scroll through the Parameter 1 list and select the desired item.

If items are available in the Parameter 2 list, select the desired item.

5. Touch the OK button.

Assigning a feature to the footswitch

1. Touch the Foot Switch button.

2. Touch the Foot Switch setup button.

The configuration screen is displayed.

3. Scroll through the Function list and select the desired feature.

4. Scroll through the Parameter 1 list and select the desired item.

If items are available in the Parameter 2 list, select the desired item.

5. Touch the OK button.

Toolbar

Reference Manual

TF series

CUSTOM FADER BANK screen

The custom fader bank allows you to choose different channels, regardless of type (input

channels, AUX buses, MATRIX (V2.5 and later), DCA groups, etc.), and group them into a

bank of faders.

1 Fader buttons

Allow you to select which fader will be configured.

2 Channel buttons

Determines which channel will be assigned to the fader you selected for

If you select None, nothing will be assigning to the corresponding fader.

Configuring the custom fader bank

1. Touch a fader button to select the fader that you want to configure.

2. Touch the desired the channel button according to which channel you want to

assign to the fader you selected in step 1.

3. Repeats steps 1–2 and configure other faders as desired.

CUSTOM FADER BANK screen menu

Touch the Menu key ( ) from the CUSTOM FADER BANK screen to display the following

items.

1 Clear All

Clears all assignments for each fader bank (all will

be set to None).

Recalling the CUSTOM FADER BANK (TF5/TF3/TF1)

1. Press the [INPUT2] and [OUTPUT] keys on the top panel at the same time.

Toolbar

Reference Manual

TF series

BUS SETUP screen

Allows you to configure bus settings. You can change basic settings such as stereo/mono, Pan

Link, etc. These settings are included when saving a Scene.

1 AUX1/2–AUX7/8 signal type selection button

MATRIX1/2–MATRIX3/4 signal type selection button (V3.5 and later)

Determines how each pair of buses is processed. You can set each pair to be either

Stereo (an odd and even numbered bus are paired and main parameters are shared

between the two) or MONO x2 (two independent mono channels).

2 Pre Fader Send Point selection button

Selects the send point when Pre is on, for the send from the input channel to the AUX

bus.

Pre EQ: directly before EQ

Pre Fader: directly before fader

3 AUX1/2–AUX7/8 Pan Link buttons

Turns pan link on and off for AUX1/2–AUX7/8.

These buttons are only displayed if the Signal Type of the corresponding bus is set to

Stereo. When these buttons are turned on, the pan setting of signals sent from input

channels to the corresponding two buses will link with the Stereo bus pan setting.

4 AUX9/10–AUX19/20 Pan Link buttons

Turns pan link on and off for AUX9/10–AUX19/20.

5 STEREO/SUB Level Link

When turned on, the levels of the STEREO channel and the SUB channel are linked.

For V3.0 and later, when turned on, the gain for both channels can be adjusted together

but the difference in gain between the two channels is maintained.

Additionally, for TF5/TF3/TF1, you can adjust the difference in gain between the two

channels by adjusting the faders while pressing the [SEL] key on the panel.

ձղ

Toolbar

Reference Manual

TF series

OMNI OUT screen

Allows you to configure the output channels that are sent to the OMNI OUT jacks.

1 OMNI OUT1–16 buttons

Allows you to select which OMNI OUT jack will be configured.

The name of the channel currently assigned to each OMNI OUT jack is also displayed in

the buttons.

2 Output channel buttons

Determines which output channel or monitor output will be assigned to the OMNI OUT

jack you selected for

1. If you select None, nothing will be output to the corresponding

OMNI OUT jack.

OMNI OUT screen menu

Press the Menu key ( ) from the OMNI OUT screen to display the following items.

SLOT SETUP screen (V2.0 and later)

Displays settings and information related to the IO Rack Tio1608-D, DZR-D series powered

speaker system, DXS-XLF-D series powered subwoofer system that are connected to the

console via the NY64-D that is installed in the expansion slot.

The information that is displayed varies depending on the connection status of the each

device

and the Quick Config settings.

1 SLOT display area (V3.1 and later)

Displays the status of the expansion slot.

If no NY card is installed, "No Card" is displayed.

If an NY64-D is installed and Dante Device Lock has been enabled, a lock icon is

displayed.

1 Clear All

Clears all assignments for each OMNI OUT jack (all

will be set to None).

NOTE

Quick Config automatically configures essential settings, making it easy to connect the Tio1608-D, DZR-

D series, and DXS-XLF-D series. Quick Config automatically configures the Dante network settings and

audio signal patching for connections between one TF series console and up to a total of 24 Tio1608-D

interfaces (max. of 3), DZR-D series speakers and DXS-XLF-D series speakers.

For information about Tio1608-D, DZR-D series, and DXS-XLF-D series settings, refer to the

documentation for the each device.

ձղ

ճմ յ

Toolbar

Reference Manual

TF series

If the NY64-D is operating in Dante AES67 mode, "AES67" is displayed above and to the

right of the SLOT display area.

When the NY64-D is installed and is pressed, the screen shown below will be

displayed to configure the settings for the NY64-D Dante Domain Manager, AES67

Mode and Device Lock (available from V3.6).

Dante Domain Manager

STATE: Displays the enrollment status of the Dante domain

LOCAL: Displays whether the Dante settings for the current device in operation

(including patches) can be modified

REMOTE:

Displays whether the Dante settings for the targeted remote device can be modified

AES67 MODE Displays the operating status of AES67 mode

Device Lock Displays whether Dante Device Lock is enabled

2 Device selection button (DZR button is V3.6 and later)

Switches between devices to show their information.

When displaying the Tio1608-D, use the Tio #1, Tio #2 and Tio #3 buttons to select the

Tio1608-D unit ID.

When displaying the DZR-D series and DXS-XLF-D series, select the DZR button.

When the connected Tio1608-D is operating in Dante AES67 mode, "AES67" will be

displayed to the upper right of the device selection buttons.

When an error occurs on a device, the error details will appear below the device

selection button.

If Dante Device Lock has been enabled for the device, a lock icon is displayed on the

Device selection button. (V3.1 and later)

3 Quick Config button

Turns the console's Quick Config feature on and off.

Displayed in gray when turned off, and white when turned on.

Displayed in orange if the Dante settings set by Dante Controller differ from the Quick

Config settings.

For information about Tio1608-D channel support when using Quick Config, see "Quick

Config Input and input channel relationships" (page 106).

The channels for the DZR-D series and DXS-XLF-D series that are patched when Quick

Config is used can be specified by selecting "Quick Config" in "UTILITY > DANTE SETUP

> MODE" on the DZR/DXS, and then PATCH.

If enrolled in the Dante domain, the Quick Config function is turned off.

NOTE

Dante Controller (v3.10.0.19 and later) is required in order for the NY64-D to operating in AES67 mode.

Domain Enrolled to the Dante domain.

Disconnected Enrolled to the Dante domain, but not connected to the DDM server.

Unmanaged Not enrolled to the Dante domain, but connected to the DDM server.

----- Not enrolled to the Dante domain or connected to the DDM server.

Read Write Can be modified.

Read Only Cannot be modified.

----- Not enrolled to the Dante domain or connected to the DDM server.

Operator Can be written.

Guest Can only be read. Cannot be modified.

None Cannot be written.

----- Not enrolled to the Dante domain or connected to the DDM server.

Disabled Not operating in AES67 mode.

Enable Operating in AES67 mode.

Unlocked Dante Device Lock is disabled.

Locked Dante Device Lock is enabled.

NOTE

• Dante Device Lock is a feature that prevents unintended operation. Dante Controller (v3.10.0.19 and

later) is required to use Dante Device Lock.

• Dante Controller (v3.10.0.19 and later) is required in order for the Tio1608-D to operate in AES67

mode.

Toolbar

Reference Manual

TF series

4 with OUTPUT checkbox

Determines whether the device OUTPUT ports are connected to the console when the

console is turned on and Quick Config is enabled.

When the checkbox is turned on and if Quick Config is enabled, the device and the

console are patched automatically.

This checkbox can be turned on and off when the Quick Config button is turned off.

5 HA Control button

Determines whether the head amp of the Tio1608-D, R series and so on is controlled by

the TF series.

Turning this button ON and OFF has no effect on the DZR-D series and the DXS-XLF-D

series.

Displayed in gray when turned off, and white when turned on.

When turned off, analog gain and +48V phantom power is disabled for input channels

set to SLOT, and the current setting is displayed.

Information about the Tio1608-D

6 SYSTEM and SYNC indicators

Display the same information as the [SYSTEM] and [SYNC] indicators on the Tio1608-D.

7 Quick Config status indicator

Indicates the status of the Tio1608-D's [QUICK CONFIG] switch.

Displayed in gray when turned off, and white when turned on.

Displayed in orange if the Dante settings set by Dante Controller differ from the Quick

Config settings.

8 +48V Master status indicator

Indicates the status of the Tio1608-D's +48V Master switch.

Displayed in gray when turned off, and red when turned on.

9 Version information

Displays the version of the Tio1608-D firmware, as well as the Dante firmware contained

in the Tio1608-D.

0 Identify button

Helps you identify the connected Tio1608-D. While this button is being touched, the

LED on the corresponding Tio1608-D flashes.

NOTE

• You can use Dante Controller to change Dante patches even when the Quick Config feature is

enabled. However, Quick Config patching will be applied when you restart the console.

If you want to use Dante Controller to change these settings, disable the Quick Config feature.

• If devices that are configured by Quick Config are also locked by Dante Device Lock, a message is

displayed and the Quick Config may not be implemented. (V3.1 and later)

• Up to 24 I/O racks (such as the Tio1608-D and R series), powered speaker systems (DZR-D series),

and powered subwoofer systems (DXS-XLF-D series) can be connected within the same Dante

network. If more racks are connected, a message is displayed and the HA control may not operate

properly.

NOTE

• When Quick Config is enabled, only one TF series console that can use the OUTPUT ports of the

devices to connect can be on the same network. For DZR-D series and DXS-XLF-D series, it will

switch to the patch with the TF series that is last connected, so use the one TF series that turn on the

with OUTPUT checkbox in the network. Also, if one or more other Tio1608-D on the network have

OUTPUT ports used by another TF series console, the "with OUTPUT" check box turns off

automatically and a pop-up screen is displayed.

• When the with OUTPUT checkbox is turned off and you are using Dante Controller for patching, refer

to "Quick Config Input and input channel relationships" (page 106) for information about output port

assignments for channels.

NOTE

• When there are multiple host devices on the same network that can control the head amp, repeated

operations could result, therefore we recommend having only one host device control the head amp.

• Even when Quick Config is turned off, you can use Dante Controller to patch into the corresponding

SLOT input channel (refer to "Quick Config Input and input channel relationships" (page 106)) and

control the head amp for up to 8 I/O racks.

NOTE

If the audio signals of the Tio1608-D that corresponds to the UNIT ID button are patched, the Identify

button and various information about the Tio1608-D (error details, status, and version) are displayed,

regardless of the Quick Config button status.

Toolbar

Reference Manual

TF series

A Channel display area

The following information is displayed when the console's Quick Config button is turned

on and a Tio1608-D with the [QUICK CONFIG] switch turned on is connected.

• CH Name

• CH Color

• +48V setting for each channel (the indicator below and to the left of the channel icon

lights in red when turned on)

Information about the DZR-D series and DXS-XLF-D series

B Device information

Touch "Device " on the list item name to sort the device information.

Touch the Version button to switch between the LIMIT/SIGNAL indicator and the

version information.

Padlock icon

This icon is displayed when Dante Device Lock on the DZR-D series and DXS-XLF-D

series is enabled.

Device information

Icons indicating the DZR-D series and DXS-XLF-D series, as well as the unit ID, product

name and Dante device name are shown.

Alert icon

This icon is displayed when an error occurs on the DZR-D series and DXS-XLF-D series.

LIMIT indicator

This indicator lights when the limiter on the DZR-D series and DXS-XLF-D series is active.

SIGNAL indicator

This indicator lights in response to the output level of the DZR-D series and DXS-XLF-D

series.

Version display (switch using button)

Displays the version of the DZR-D and DXS-XLF-D series firmware, as well as the Dante

firmware contained in the DZR-D series and the DXS-XLF-D series.

Identify button

Helps you identify the DZR-D Series and DXS-XLF-D series that is connected. While you

hold down this button, the backlight on the corresponding DZR-D series and DXS-XLF-

D series flashes.

C Output information

Displays information for the TF output channels that are outputted to the DZR-D series

and DXS-XLF-D series.

Touch the "Output" list item name to sort by TF output channel (in order of AUX 

MTRX  ST  SUB  MONITOR).

D Mute buttons

Switches the mute function ON/OFF for the DZR-D series and DXS-XLF-D series systems.

If the connected DZR version is V1.1.1 or earlier, then Mute buttons are not displayed.

NOTE

The information below (B C) is not displayed when Quick Config or "with OUTPUT" is disabled.

ռսվ

NOTE

The Identify button displays when Quick Config is enabled.

Toolbar

Reference Manual

TF series

RECALL SAFE screen

Allows you to configure which items are recalled and which items are not (i.e., recall safe)

when recalling Scenes and Presets.

"Recall safe" allows you to select certain parameters, channels, DCA groups, etc. whose

settings will not be replaced when recalling a Preset or Scene.

1 Channel selection buttons

Allows you to select which types of channels will be configured.

When you select a channel type, the different parameters that can be configured as

recall safe are displayed.

2 Parameter names

Touch the

button to turn SAFE parameters on and off for all channels of the same type.

The

button turns green when all SAFE parameters are turned on. If turned off for a parameter

on all channels, it is displayed in gray. Finally, if recall safe is turned on for a parameter

but not for all channels, the M button under the parameter name is displayed in blue.

3 Recall safe on/off buttons

Turns recall safe on and off for the corresponding parameter. When turned on, the

corresponding parameter is recall safe, i.e., its setting will not be changed when a Preset

or Scene is recalled.

For OMNI OUT assignments, recall safe can be turned on and off for OMNI OUT PATCH

only.

4 Channel information

Displays the channel ID, name, and icon.

Touch the SAFE button to turn safe recall on and off for the corresponding channel.

When turned on, parameters whose recall safe on/off buttons are in the "on" position

will not be recalled.

Using Recall safe function

1. Touch a channel selection button to select the channels or DCA groups that you

want to configure for recall safe.

2. Touch the recall safe on/off buttons

according to the items you want to make

recall safe.

3. Touch the SAFE buttons for each channel

to enable or disable the settings you

made above.

4. Touch the [X] button to close the screen,

and proceed to recall the desired Preset

or Scene.

Recall safe on/off buttons

SAFE buttons

Toolbar

Reference Manual

TF series

MUTE GROUP ASSIGN Screen (V4.0 and later)

Allows you to configure the mute group and mute safe for each input channel.

INPUT (MUTE GROUP1) and FX (MUTE GROUP2) are preassigned for the mute groups.

Input channels or FX1/FX2 can be assigned for the other mute groups (MUTE GROUP3

through MUTE GROUP6).

Use the mute safes to exclude a channel from the mute group operations. ST IN1 and ST IN2

are assigned as default settings.

1 Mute group name

Touch the pencil icon at the top right to display the edit screen.

Touch to switch between information for different mute groups.

2 Mute Group Master button

Switches the currently displayed mute group on and off. When this is off, the relevant

mute group will be disabled.

3 MUTE GROUP ASSIGN buttons

Use these buttons to select the input channels that will be assigned to the currently

displayed mute group.

ձ ղ

Assigning channels to mute groups

1. Touch the buttons for the mute group

name to display the mute group to be created.

2. Touch the Mute Group Master button to switch

it on.

3. Touch to select the channels to assign to the

mute group.

4. If necessary, name the mute group by touching the pencil icon for the mute group

name.

5. To specify mute safe channels, touch the mute group name buttons to

display Mute Safe.

Toolbar

Reference Manual

TF series

MUTE GROUP ASSIGN screen menu

Press the Menu key ( ) on the MUTE GROUP ASSIGN screen to display the menu icons

shown below.

BRIGHTNESS screen

Allows you to adjust the brightness of the touchscreen, as well as the LEDs, name display,

and channel colors on the top panel. You can save brightness settings into BANK A and BANK

B, allowing you to recall the desired brightness settings to suit your work conditions.

1 Bank selection buttons

Allow you to switch between BANK A and BANK B.

BANK A: Selects BANK A brightness settings.

BANK B: Selects BANK B brightness settings.

For V1.1 and later, you can switch between the banks using [USER DEFINED KEYS] or a

footswitch.

6. Touch to select channels to assign as mute safe channels.

7. When finished, touch the button at the top right of the screen.

1 Clear All

Unassigns all channels assigned to the mute

group.

ղձ

TF5/TF3/TF1

ղձ

TF-RACK

Toolbar

Reference Manual

TF series

2 Power Saving Mode button

Allows you to set the amount of time that passes before console switches to power saving mode.

You can choose 30 seconds, 2 minutes, 5 minutes, 10 minutes, 15 minutes, or never.

3 Screen brightness slider

Adjusts the brightness of the touchscreen.

4 Panel brightness slider

Adjusts the brightness of the LEDs on the top panel.

1–10: In low lighting conditions, an auxiliary light lights, which makes the key top easier

to read.

11–20: In bright lighting conditions, an auxiliary light does not light, which helps

emphasize contrast.

5 CH Name brightness slider (TF5/TF3/TF1)

Adjusts the brightness of the channel names displayed on the top panel.

6 CH Color brightness slider (TF5/TF3/TF1)

Adjusts the brightness of the channel colors on the top panel.

NETWORK screen

Allows you to configure the console's network address, which is needed when you connect a

computer to the NETWORK connector.

Configure these settings according to the connected computer or network.

1 IP address provisioning method button

Select the setting that matches how the console will configure its IP address.

DHCP: The console receives its IP address automatically.

Static IP: The console's IP address is set manually.

2 IP Address

Determines the unique address that identifies the console on the network.

3 Subnet Mask

Defines how many bits are used for network addresses on the connected network.

4 Gateway

The address of the network device (gateway) that facilitates communication between

different devices on the network.

5 Unit Name

Allows you to specify a name that can be used to identify the console on the network.

6 PIN for MonitorMix (V1.1 and later)

This is a 4-digit password that is required when accessing the console using the

MonitorMix app.

MonitorMix is an application that allows performers to adjust the levels of the monitor

mix directly from the stage.

7 Refresh button (V3.6 and later)

The method of acquiring IP addresses will be shown for DHCP.

Press this button to reacquire an address from the DHCP server.

NOTE

When connecting the console to a LAN, refer to the TF Editor Installation Guide.

NOTE

When the DHCP button is selected, items 2–4 are not needed.

2–4 are only needed when you select the Static IP button. Configure these parameters as needed.

Toolbar

Reference Manual

TF series

TIME screen

Allows you to set the console's internal clock and change the date and time format. The date

and time set here are used as a timestamp when saving Scenes.

1 Date setting

Determines the console's date setting.

2 Date format setting

Allows you to select the date format.

The following formats are available.

MM/DD/YYYY

DD/MM/YYYY

YYYY/MM/DD

3 Region

Allows you to change the region.

4 DST (+1:00)

Enables daylight saving time.

When turned on, the current time advances by one hour.

5 Time format setting

Allows you to select the time format.

24-Hour

12-Hour (uses AM and PM)

6 Time setting

Determines the console's time setting.

LOG screen

When messages are displayed while using the console, they are logged by date and time and

can be viewed later on this screen.

1 Time Stamp field

Displays the date and time of each message.

You can touch the header to sort messages by date and time.

2 Message field

Displays messages.

You can touch the header to sort messages alphabetically by message.

3 Save button

Allows you to save the log to a USB storage device.

This button is not available when no USB storage device is connected.

ձղ ճ մ

ձղ

Toolbar

Reference Manual

TF series

HELP screen

Displays information about console operations. If "Show Help at Startup" is turned on in the

PREFERENCE screen, the HELP screen is displayed automatically after the console starts

up.

You can swipe left and right to view different pages.

ABOUT screen

Displays system software version information and license information.

1 Version button

Displays the console's system software version number.

(V2.0 and later) Displays the Dante version of the connected NY64-D, if installed.

2 License button

Displays system software license information.

ձղ

Toolbar

Reference Manual

TF series

Allows you to assign permissions for accessing the TF series console.

By limiting which parameters can be operated by different users, you can prevent improper

operation and specify what guest engineers can and cannot do when operating the console.

1 User icons

Display the icon, name, and comments for each user.

When you touch an item, the console prompts you to enter the password for the

corresponding user.

If there is no password assigned to a user, you can log in by simply touching the user's icon.

Administrator

Can use all features. Only one administrator can be configured for the console.

The administrator is the only user that can set the access permissions of other users.

If another user has locked the console, the administrator can release the console lock.

The only setting that must be set for the administrator is the password.

Guest

Can use features according to the access permissions set by the administrator. Only one

guest can be configured for the console.

Access permissions and comments can be assigned to the guest.

User

Can use features according to the access permissions set by the administrator. Three

users can be configured for the console.

A user name, password, access permissions, and comments can be assigned to each user.

2 Console lock icon

Prompts you to enter the password for the current user.

If the correct password is entered, the CONSOLE LOCK screen is displayed. (page 46)

3 User account icon

Displays the USER ACCOUNT screen.

USER ACCOUNT screen (V3.0 or later)

Allows the administrator to set the access permissions for the other users.

1 User selection area

Allows you to select which user's settings you will configure.

Information about the selected user is displayed on the right side of the screen.

2 User Name text box

Displays the keyboard screen so that you can edit the user name.

You cannot edit the user name of the administrator and guest accounts.

3 Password Edit button

Displays the keyboard screen so that you can edit the password.

NOTE

• There is no password saved for the administrator in the factory default settings. (All users have

full access.)

In order to set permissions for other users, you must first set a password for the administrator.

• If a user with a password assigned is logged in to the console when the console is turned off, the

console will prompt the user to enter that password when the console is turned on the next time.

If another user wants to log in, press the cancel button when prompted to enter the password, and

then select the desired user in the LOGIN screen.

Toolbar

Reference Manual

TF series

When setting a password for the first time, enter the desired password in the New

Password text box, and then enter the password again in the Verify text box. When

changing a password, enter the current password in the Old Password text box, and

then set the new password.

4 Comment text box

Displays the keyboard screen so that you can enter a comment.

5 Access Permission Edit button

Displays the ACCESS PERMISSION screen.

When logged in as the administrator, you can set the access permissions of the selected

user for each parameter.

ACCESS PERMISSION screen (V3.0 and later)

Allows you to select which parameters can be used and not used by each user.

This screen is only displayed when logged in as the administrator.

1 Selection buttons

Allows you to select a channel to assign access permission to.

According to which button you have selected, the different parameters that can be

assigned access permissions are displayed.

You can set access permissions for operations that are not associated with channels, such

as the SETUP screen or the SCENE screen, by touching the GENERAL button.

2 Parameter names

Touch the



button to allow/restrict access to the parameters for all channels of the same type.

The  button turns green when access is allowed for all channels. If access is allowed

for only some channels, it is displayed in blue, and if access is restricted for all channels,

it is displayed in gray.

3 Access permission on/off buttons

Allow (on) and restrict (off) access to the corresponding parameters.

The selected user can only use the parameters that are allowed here.

For details about each parameter, refer to the parameter list. (page 98)

4 Channel information

Displays the channel ID, name, and icon.

Touch the



button to allow/restrict access to the parameters for the corresponding channel.

The  button turns green when access is allowed for all parameters. If access is allowed

for only some parameters, it is displayed in blue, and if access is restricted for all

parameters, it is displayed in gray.

ACCESS PERMISSION screen menu

Press the Menu key ( ) from the ACCESS PERMISSION screen to display the following options.

1 Copy

Copies the ACCESS PERMISSION settings of the

selected user to the clipboard.

2 Paste

Pastes the ACCESS PERMISSION settings in the

clipboard to the selected user.

3 High Level

4 Mid Level

5 Low Level

Applies ACCESS PERMISSION settings to the

selected user based on their proficiency.

High Level: For advanced users. Only network and

clock settings are restricted. All other

parameters are allowed.

Mid Level: For moderately proficient users.

System settings are restricted. All other

parameters, such as channel

operations, are allowed.

Low Level: For beginners. Most parameters are

restricted. Channel on/off and fader

level adjustments are allowed.

Toolbar

Reference Manual

TF series

CONSOLE LOCK screen

You can lock the console to prevent it from being operated accidentally.

While the CONSOLE LOCK screen is displayed, controls are disabled and the console cannot

be operated.

To unlock the console, touch and hold the CONSOLE LOCK screen. If you are prompted to

enter a password, enter the password of the current user or the administrator.

Applying access permissions

1. From the LOGIN screen, log in as the administrator.

2. From the LOGIN screen, touch the User Account icon to display the USER ACCOUNT

screen.

3. Select the desired user, then set the user name, password, and comments.

4. Touch the Access Permission Edit button to display the ACCESS PERMISSION screen.

5. Restrict (turn off) the parameters that you do not want the user to access.

6. To confirm whether the access permissions were set as desired, return to the LOGIN

screen and log in as the user you set access permissions for.

7. Operate a parameter that you restricted. "Permission Denied!" is displayed if the

parameter is restricted.

Resetting user settings

If the console is reset, all user passwords are deleted and all restrictions are released.

(page 93)

Loading user settings to other TF series consoles

1. From the SAVE/LOAD screen, save the console's internal settings.

2. Log in as the administrator using the console to which you want load the user

settings.

3. From the SAVE/LOAD screen, select the settings file you saved in step 1 and touch

the Load button.

4. From the LOAD SELECT screen, select user accounts on the CUSTOM tab and touch

the Load button.

OVERVIEW screen

Reference Manual

TF series

OVERVIEW screen

Displays information about the channel strips.

You can display the OVERVIEW screen by pressing the Home key ( ).

For the TF5/TF3/TF1, the CH STRIP section is displayed as the home screen; for the

TF-RACK, the FADER section is displayed. Additionally, for the TF-RACK, you can switch

between the CH STRIP section and FADER section by pressing the Home key.

CH STRIP section

Input channels

1 Displays the INPUT screen. (page 57)

2 Displays the EQ screen. (page 59)

3 Displays the GATE screen. (page 63)

4 Displays the COMP screen. (page 65)

5 Displays the FX1 screen. (page 67)

6 Displays the FX2 screen. (page 67)

7 Displays the SEND TO AUX screen. (page 73)

8 Displays the ASSIGN screen. (page 74)

9 Displays the AUTOMIXER screen (V3.5 and later). (page 74)

0 Displays the CH VIEW screen. (page 76)

Stereo channels

1 Displays the INPUT screen. (page 57)

2 Displays the EQ screen. (page 59)

3 Displays the DELAY screen. (page 92)

4 Displays the FX1/FX2 screen. (page 67)

5 Displays the SEND TO AUX screen. (page 73)

6 Displays the ASSIGN screen. (page 74)

7 Displays the CH VIEW screen. (page 76)

NOTE

For the TF5/TF3/TF1, the FADER section is displayed on the OVERVIEW screen when

SETUPPREFERENCEKey Function[HOME] key is set to "Fader". Each touch of the [Home] key

successively displays the next selected section.

ջ ղյն

շմ

OVERVIEW screen

Reference Manual

TF series

8 Displays the GEQ screen. (page 85)

9 Displays the COMP screen. (page 65)

0 Displays the OUTPUT screen. (page 87)

A Displays the SEND FROM screen (page 88) (V3.0 and later)

AUX1–AUX8 channels

1 Displays the SEND FROM screen. (page 88)

2 Displays the EQ screen. (page 59)

3 Displays the GEQ screen. (page 85)

4 Displays the COMP screen. (page 65)

5 Displays the OUTPUT screen. (page 87)

6 Displays the CH VIEW screen. (page 76)

AUX9/10–19/20 channels, SUB channel

1 Displays the SEND FROM screen. (page 88)

2 Displays the EQ screen. (page 59)

3 Displays the COMP screen. (page 65)

4 Displays the FX screen. (page 67)

5 Displays the OUTPUT screen. (page 87)

6 Displays the CH VIEW screen. (page 76)

MATRIX1–4 channels (V2.5 and later)

1 Displays the SEND FROM screen. (page 88)

2 Displays the EQ screen. (page 59)

3 Displays the DELAY screen. (page 92)

OVERVIEW screen

Reference Manual

TF series

4 Displays the OUTPUT screen. (page 87)

5 Displays the CH VIEW screen. (page 76)

Group channels

1 Displays the DCA ASSIGN screen. (page 90)

2 Displays the CH VIEW screen. (page 76)

FADER section

1 ON button

Turns the channel on and off.

2 Fader

Adjusts the channel’s fader level.

3 CUE button

Turns the cue on and off for the assigned channel.

4 Displays the CH VIEW screen. (page 76)

NOTE

• MATRIX channels 1–4 are in the OUTPUT FADER BANK. To use the faders on the top panel to control

these channels, press the [OUTPUT] key in the FADER BANK section, and then display the OUTPUT

BANK in the channel strip.

• For TF1, MATRIX channels 1–4 are not controlled by the faders, and are displayed only. Scroll the

displayed area to the right. To control these channels using the faders, register them to the CUSTOM

FADER BANK.

OVERVIEW screen

Reference Manual

TF series

SELECTED CHANNEL section (V4.0 and later)

CH1–CH32

1 Displays the FX1 screen. (page 67)

2 Displays the FX2 screen. (page 67)

3 Displays the SEND TO AUX screen. (page 73)

4 Displays the ASSIGN screen. (page 74)

5 Displays the CH VIEW screen. (page 76)

6 Displays the HA status.

You can adjust the gain by touching to highlight it, and then turning the [TOUCH AND

TURN] knob.

Touch when highlighted to display the INPUT screen. (page 57)

Two HAs are displayed on channels for which the stereo link is configured.

7 Displays the ON/OFF status for the input port and DIRECT OUT.

8 Displays the AUTOMIXER screen. (page 74)

9 Displays the LIBRARY screen. (page 8)

0 Controls the channel EQ.

The button switches between 1-knob and manual modes.

Select the 1-knob EQ mode type and switch between filter types on the EQ screen.

Touch the icon to display the EQ screen. (page 59)

A Configures the GATE for the channel.

Touch the icon to display the GATE screen. (page 63)

B Configures the COMP for the channel.

The button switches between 1-knob and manual modes.

Touch the icon to display the COMP screen. (page 65)

CH33–CH40

1 Displays the FX1 screen. (page 67)

2 Displays the FX2 screen. (page 67)

3 Displays the SEND TO AUX screen. (page 73)

4 Displays the ASSIGN screen. (page 74)

5 Displays the CH VIEW screen. (page 76)

6 Displays the HA status.

You can adjust the gain by touching to highlight it, and then turning the [TOUCH AND

TURN] knob.

Touch when highlighted to display the INPUT screen. (page 57)

7 Displays the input port.

8 Displays the LIBRARY screen (page 8).

NOTE

In the EQ, GEQ, GATE and COMP of the SELECTED CHANNEL section, operations can be performed

either by dragging or by touching the given parameter to highlight it and then operating the [TOUCH AND

TURN] knob.

նշոչ

նշ ո

OVERVIEW screen

Reference Manual

TF series

9 Controls the channel EQ.

The button switches between 1-knob and manual modes.

Select the 1-knob EQ mode type and switch between filter types on the EQ screen.

Touch the icon to display the EQ screen. (page 59)

ST IN1L–2R

1 Displays the FX1 screen. (page 67)

2 Displays the FX2 screen. (page 67)

3 Displays the SEND TO AUX screen. (page 73)

4 Displays the ASSIGN screen. (page 74)

5 Displays the CH VIEW screen. (page 76)

6 Displays the HA status.

You can adjust the gain by touching to highlight it, and then turning the [TOUCH AND

TURN] knob.

Touch when highlighted to display the INPUT screen. (page 57)

7 Displays the input port.

8 Displays the DELAY screen. (page 92)

9 Displays the LIBRARY screen. (page 8)

0 Controls the channel EQ.

The button switches between 1-knob and manual modes.

Select the 1-knob EQ mode type and switch between filter types on the EQ screen.

Touch the icon to display the EQ screen. (page 59)

FX1L–2R

1 Displays the SEND FROM screen. (page 88)

2 Displays the FX screen. (page 67)

3 Displays the SEND TO AUX screen. (page 73)

4 Displays the ASSIGN screen. (page 74)

5 Displays the CH VIEW screen. (page 76)

6 Displays the LIBRARY screen. (page 8)

7 Controls the channel EQ.

The button switches between 1-knob and manual modes.

Select the 1-knob EQ mode type and switch between filter types on the EQ screen.

Touch the icon to display the EQ screen. (page 59)

նշոչ

OVERVIEW screen

Reference Manual

TF series

ST L/R

1 Displays the OUTPUT screen. (page 87)

2 Displays the CH VIEW screen. (page 76)

3 Displays the LIBRARY screen. (page 8)

4 Controls the channel EQ.

The button switches between 1-knob and manual modes.

Select the 1-knob EQ mode type and switch between filter types on the EQ screen.

Touch the icon to display the EQ screen. (page 59)

5 Controls the channel GEQ.

For TF1, TF3, and TF5 models, touch the icon to switch it on, so that the faders can

be operated on the top panel.

Touch the icon to display the GEQ screen. (page 85)

6 Controls the channel COMP.

The button switches between 1-knob and manual modes.

Touch the icon to display the COMP screen. (page 65)

AUX1–AUX8

1 Displays the SEND FROM screen. (page 88)

2 Displays the OUTPUT screen. (page 87)

3 Displays the CH VIEW screen. (page 76)

4 Displays the LIBRARY screen. (page 8)

5 Controls the channel EQ.

The button switches between 1-knob and manual modes.

Select the 1-knob EQ mode type and switch between filter types on the EQ screen.

Touch the icon to display the EQ screen. (page 59)

6 Controls the channel GEQ.

For TF1, TF3, and TF5 models, touch the icon to switch it on, so that the faders can

be operated on the top panel.

Touch the icon to display the GEQ screen. (page 85)

7 Controls the channel COMP.

The button switches between 1-knob and manual modes.

Touch the icon to display the COMP screen. (page 65)

OVERVIEW screen

Reference Manual

TF series

AUX9–AUX20

1 Displays the SEND FROM screen. (page 88)

2 Displays the FX screen. (page 67)

3 Displays the OUTPUT screen. (page 87)

4 Displays the CH VIEW screen. (page 76)

5 Displays the LIBRARY screen. (page 8)

6 Controls the channel EQ.

The button switches between 1-knob and manual modes.

Select the 1-knob EQ mode type and switch between filter types on the EQ screen.

Touch the icon to display the EQ screen. (page 59)

7 Controls the channel COMP.

The button switches between 1-knob and manual modes.

Touch the icon to display the COMP screen. (page 65)

SUB

1 Displays the SEND FROM screen. (page 88)

2 Displays the OUTPUT screen. (page 87)

3 Displays the CH VIEW screen. (page 76)

4 Displays the LIBRARY screen. (page 8)

5 Controls the channel EQ.

The button switches between 1-knob and manual modes.

Select the 1-knob EQ mode type and switch between filter types on the EQ screen.

Touch the icon to display the EQ screen. (page 59)

6 Controls the channel COMP.

The button switches between 1-knob and manual modes.

Touch the icon to display the COMP screen. (page 65)

OVERVIEW screen

Reference Manual

TF series

MATRIX1–MATRIX4

1 Displays the SEND FROM screen. (page 88)

2 Displays the OUTPUT screen. (page 87)

3 Displays the CH VIEW screen. (page 76)

4 Displays the DELAY screen. (page 92)

5 Displays the LIBRARY screen. (page 8)

6 Controls the channel EQ.

The button switches between 1-knob and manual modes.

Select the 1-knob EQ mode type and switch between filter types on the EQ screen.

Touch the icon to display the EQ screen. (page 59)

DCA1–DCA8

1 Displays the DCA ASSIGN screen. (page 90)

2 Displays the CH VIEW screen. (page 76)

մյ

OVERVIEW screen operations

When you touch an item on the screen, a pink box is displayed around the item to highlight it.

When an item is highlighted, you can adjust it using the [TOUCH AND TURN] knob.

If you touch a highlighted item, its configuration screen is displayed.

You can drag or swipe up, down, left, and right to display other areas of the screen.

OVERVIEW screen

Reference Manual

TF series

OVERVIEW screen menu

Press the Menu key ( ) from the OVERVIEW screen to display the following items.

1 CH Copy

Copies the settings of the current channel.

2 CH Paste

Pastes settings from another channel and applies

them to the current channel.

3 CH Default

Resets the settings of the current channel to their

default values.

AUX/MATRIX channels (V4.0 and later)

4 CH Copy with Sends

Copies and also sends current channel settings.

5 CH Paste with Sends

Pastes settings copied from the selected channel,

including sending. When CH Copy with Sends is

executed, the CH Paste icon changes to CH Paste

with Sends.

Copying settings from one channel and applying them to another channel

1. Select the channel whose settings you want to copy.

2. Press the Menu key ( ).

Displays the menu.

3. Touch the CH Copy icon.

The settings are copied and the menu closes.

Copy settings from this channel

CH Copy icon

OVERVIEW screen

Reference Manual

TF series

4. Select the channel that you want to apply the settings to.

5. Press the Menu key ( ).

Displays the menu.

6. Touch the CH Paste icon.

The settings from the first channel you selected are applied to the second channel you selected, and

then the menu closes.

Settings will be applied to this channel

CH Paste icon

Paste completed

Configuration screens

Reference Manual

TF series

Configuration screens

INPUT screen

Allows you to change the stereo link setting, select an input source, turn phantom power on

and off, turn phasing on and off, and adjust input gain.

1 Stereo link selection button

Allows you to select whether two adjacent mono input channels are linked as a stereo

pair, or behave as two separate mono channels. Touch to display the popup menu.

OFF: Stereo link is disabled.

CH1&2: Stereo link is enabled. When stereo link is enabled, the odd numbered channel

is the left side of the stereo pair, and the even numbered one is the right. The

channel numbers displayed in the popup menu depend on the channel whose

settings you are editing.

CH2&3: Stereo link is enabled. When stereo link is enabled, the even numbered channel

is the left side of the stereo pair, and the odd numbered one is the right. The

channel numbers displayed in the popup menu depend on the channel whose

settings you are editing.

2 Input selection buttons

Allows you to select the channel's input source. The available sources depend on the

channel whose settings you are editing.

INPUT: The device connected to the INPUT jack will be used as the input source.

USB: The computer connected to the USB TO HOST connector will be used as the input

source.

SLOT (V2.0 and later): Allows you to select an input from the NY64-D installed in the

expansion slot. Use this button when selecting an input from a

Tio1608-D or stage box connected to the NY64-D and the

Dante network. See page 106 for information about SLOT port

numbers and channels.

Playback:

Displayed for ST IN1. Allows you to select a USB storage device that is connected

to the USB connector on the top panel as an input.

Even if you select SLOT as the input source, if a source is not actually available (such as

when there is no NY64-D installed, no Tio1608-D or stage box connected, no Dante

patching, etc.), this "virtual HA" state is displayed in the HA box area of this screen, the

OVERVIEW screen, and the CH VIEW screen.

3 GainFinder

Displays the input's gain adjusted level. When adjusting the input gain, adjust it so that

the center of the GainFinder lights up. When the input source is set to INPUT, the

GainFinder displays the digital input's gain.

ձղ ճմ

յնշո

NOTE

When USB is selected, the gain slider (

) adjusts digital gain, and the +48V button (

) is not displayed.

When SLOT is selected, analog gain adjustment and the +48V button cannot be used if the HA Control

button on the SLOT SETUP screen is not turned on. Additionally, for inputs from a device whose head

amp cannot be controlled, the gain slider (

7) becomes a digital gain adjustment, and the +48V button

(

8) is not displayed.

Configuration screens

Reference Manual

TF series

4 Level meter

Displays the gain adjusted level.

5 Digital gain text box

Allows you to adjust the digital gain. It is set to 0 dB by default. You can touch the text

box to highlight it, then use the [TOUCH AND TURN] knob to adjust the setting. You

can also touch the text box again to adjust the setting using the keyboard screen.

6 Φ (phase) button

Allows you to reverse the phase.

When turned on, the input signal's phase is reversed.

7 Gain slider

When the INPUT button is selected, the slider adjusts the analog gain of the head amp.

The PAD (-24 dB) will be switched on or off when the analog gain is adjusted between

+17 dB and +18 dB.

When the USB button is selected, the slider adjusts digital gain.

8 +48V button

Turns phantom power (+48 V) to the head amp on and off.

On: Phantom power is turned on.

Off: Phantom power is turned off.

When the USB button is selected, the +48V button is not displayed.

9 Gain Unlink button (V1.1 and later)

Displayed for stereo channels and for channels that have stereo link turned on.

While you are touching the button, gain for the left and right channels can temporarily

be adjusted individually. When you release the button, the gain for both channels can

be adjusted together but the difference in gain between the two channels is maintained.

NOTICE

Information about phantom power

When phantom power is not needed, set the +48V button to the off position.

Observe the following when using phantom power to prevent damage to the console or connected

devices, and signal noise.

• Do not set the +48V button to the on position when the device connected to the input jack does

not require phantom power.

• Do not connect or disconnect cables when the +48V button is set to the on position.

• Before turning phantom power on or off for a channel, first set the channel's volume to the

minimum level.

NOTE

When using phantom power, noise may be generated if there is a difference in the impedance between

the hot and cold of the device connected to an input jack.

Setting stereo link and the input source

1. Display the INPUT screen. (page 5)

2. Touch the stereo link selection button that

corresponds to the desired setting.

3. Touch the input selection button that

corresponds to the desired setting.

4. Use the gain slider to adjust the

head amp gain.

Adjust the gain slider so that the center of

the GainFinder lights up.

5. Touch the digital gain text box to highlight

it, then use the [TOUCH AND TURN] knob to

adjust the setting.

Gain finder level display

Gain slider

Digital gain

text boxes

Configuration screens

Reference Manual

TF series

INPUT screen menu (V1.1 and later)

Touch the Menu key ( ) from the INPUT screen to display the following items.

EQ screen

Controls the EQ for each channel. 4-band parametric EQ is available for CH 1–32, AUX 1–20,

STEREO and MATRIX1-4; 2-band parametric EQ is available for CH 33–40, ST IN 1, ST IN

2, FX1, FX2, and SUB. You can adjust settings using 1-knob mode, which allows you to use

the [TOUCH AND TURN] knob to easily adjust settings, or manual mode, which allows you to

adjust each parameter individually.

4-band parametric EQ

1 EQ button

Turns the EQ on and off.

2 HPF button

Turns the HPF (high-pass filter) on and off.

Displayed for CH 1–40.

3 1-knob button

Switches between 1-knob EQ mode and manual mode.

When using 1-knob EQ mode, the 1-knob level slider is displayed.

4 1-knob level slider

Adjusts the intensity of 1-knob EQ.

When using manual mode, information about the selected band's Q, F, and G is

displayed here.

1 All INPUT

Allows you to assign the INPUT jacks as the input

source for all input channels.

2 All USB

Allows you to assign the USB TO HOST connector

as the input source for all input channels.

3 All SLOT (V2.0 and later)

Switches all inputs to input sources of Dante

network devices that are connected to the NY64-

D installed in the expansion slot.

The input source for the following channels will be

changed.

TF5:

CH 1–32 (when CH 1–32 are selected)

CH 33–40 (when CH 33–40 are selected)

TF3:

CH 1–24 (when CH 1–24 are selected)

CH 25–32 (when CH 25–32 are selected)

CH 33–40 (when CH 33–40 are selected)

TF1/TF-RACK:

CH 1–16 (when CH 1–16 are selected)

CH 17–32 (when CH 17–32 are selected)

ձղ ճ մ յ

շո

Configuration screens

Reference Manual

TF series

5 EQ mode type selection button

When using 1-knob EQ mode, allows you to select the 1-knob EQ mode type. Select

[Vocal] for vocal channels, otherwise select [Intensity].

When set to [Intensity], you can adjust the EQ to a setting between flat and double the

intensity of the EQ settings you made using manual mode.

For output channels, [Loudness] is available. This setting allows you to boost low and

high tones.

The available types depend on the channel whose settings you are editing.

In manual mode, this button switches the filter type. Low-band and high-band filter are

available.

For CH 1-40, the available low-band filters are low-shelving type and bell type.

For other channels (i.e., for channels that do not have an HPF), the available low-band

filters are HPF, low-shelving type, and bell type.

The available high-band filters are LPF, high-shelving type, and bell type.

6 EQ output level meter

Displays the post-EQ level.

7 EQ graph

Displays the parameter settings of the EQ and filter. As you adjust the settings of each

band, the results are reflected in the graph.

When using 1-knob EQ mode, you can touch the level slider and then adjust the slider

using the slider itself or the [TOUCH AND TURN] knob.

When using manual mode, you can drag the handles displayed in the graph to adjust

the corresponding settings.

When HPF is turned on, you can drag the HPF handle to adjust the cutoff frequency. You

can also adjust HPF independently when using the Intensity type for 1-knob EQ mode.

<1-knob EQ mode> <Manual mode>

How does 1-knob EQ mode work?

1-knob EQ mode allows you to adjust several parameters at once with just the turn of a knob.

It makes EQ adjustment quick and easy.

The console contains Presets that are configured for a variety of instruments. You can use 1-

knob EQ mode to adjust the EQ settings that are saved in Presets without disturbing the

overall balance of your mix.

You can even configure EQ settings using manual mode, then switch to 1-knob EQ mode and

use the Intensity type to adjust the amount of EQ applied to the channel. In this case you can

use the [TOUCH AND TURN ] knob to adjust from 0% (no EQ applied) to 50% (the EQ

settings you made using manual mode) and 100% (double the intensity of the EQ settings you

made using manual mode). This makes it very easy to fine-tune your EQ settings with just one

knob.

If 1-knob EQ mode type is set to Vocal or Loudness, you can adjust the EQ between 0% (no

EQ applied) and 100% (maximum EQ applied).

Type

Channel

CH1-32

HPF +

4-band

CH33-40

HPF +

2-band

ST IN

2-band

STEREO

4-band

AUX1-8

4-band

AUX9/10–

AUX19/20

4-band

MATRIX

1-4

4-band

SUB

2-band

+ LPF

Intensity

○○○○○○ ○ ○

Vocal

○

××××× × ××

Loudness × × × ×

○○ ○ ○

Configuration screens

Reference Manual

TF series

8 RTA/Keyboard display

You can touch the bottom of the graph where no parameters are displayed to display

RTA or a keyboard. RTA is a graph that displays the frequencies of the input signal after

the EQ is applied. The keyboard display is helpful for understanding the relationship

between frequencies and musical pitches.

NOTE

Adjusts the sensitivity of RTA for RTA Offset on the PREFERENCE screen (



page 26). Allocate the RTA

Offset to the USER DEFINED KNOBS to adjust while the EQ screen is displayed (available from V3.6).

Adjusting EQ in manual mode

1. Display the EQ screen. (page 5)

2. Touch the EQ button and turn on the EQ.

3. Touch the 1-knob button and turn 1-knob mode off.

4. Use the handles in the EQ graph to adjust the EQ as desired.

When you touch an EQ parameter to select it, you can then adjust it using the [TOUCH AND TURN]

knob. You can press the [SHIFT] key to switch to a different parameter. Each time you press the

[SHIFT] key, you can switch between gain (G) and frequency (F). You can also switch between G and

F by touching the corresponding area to the right of the 1-knob button.

To adjust Q, pinch in or out on the touchscreen, or touch the Q area to the right of the 1-knob button

and then use the [TOUCH AND TURN] knob to adjust the setting.

Holding down the [Shift] key resets the gain value to zero (V4.0 and later).

5. Turn HPF on as desired.

When using a vocal mic, you can reduce low-frequency noise (rumble noise, etc.) by turning on HPF.

Adjusting EQ in 1-knob EQ mode

1. Display the EQ screen. (page 5)

2. Turn on the EQ and select 1-knob mode.

3. Select the desired 1-knob mode type.

4. Use the [TOUCH AND TURN] knob to adjust the EQ.

Drag to adjust

Configuration screens

Reference Manual

TF series

Setting HPF

1. Display the EQ screen. (page 5)

2. Touch the HPF button and turn on the HPF.

3. Touch the HPF handle.

4. Use the [TOUCH AND TURN] knob to adjust the HPF.

You can also drag the HPF handle in the EQ graph.

The value that corresponds to your adjustments is

displayed in the upper right of the screen.

Drag to adjust

Adjusted value

Setting LPF

The SUB channel can use the LPF to cut high frequencies independent of the EQ, ideal for

adjusting the signal sent to a sub-woofer.

1. Display the SUB channel's EQ screen. (page 5)

2. Touch the EQ button and turn on the EQ.

3. Use the LPF handle in the EQ graph to adjust the LPF as desired.

Drag to adjust

Configuration screens

Reference Manual

TF series

EQ screen menu

Press the Menu key ( ) from the EQ screen to display the following options.

GATE screen

Allows you to configure the noise gate for each channel. When the input signal level is lower

than a specified amount (threshold), the output signal is reduced by a specified amount

(range). GATE is available for CH 1–32.

1 GATE button

Turns the gate on and off.

2 Gate input level meter

Displays the gate input level.

3 Threshold slider

Determines the level at which the gate is applied.

4 Gate graph

Displays a visual representation of the gate level.

5 Range slider

Determines the amount by which the signal will be lowered when the gate is applied.

6 Attack slider

When the input signal exceeds the threshold, this setting determines how quickly the

gate opens.

1 Copy

Copies the EQ parameters of the selected channel

to the clipboard.

2 Paste

Pastes the EQ parameters in the clipboard to the

selected channel.

3 Compare

Allows you to compare the EQ parameters of the

selected channel with the EQ parameters in the

clipboard by switching between the two.

4 Gain Flat

Sets the EQ gain for all bands to 0.

5 Default

Resets EQ settings to their default values.

ձյնշ

ոմճղ

Configuration screens

Reference Manual

TF series

7 Hold slider

When the input signal drops below the threshold, this setting determines how much

time passes before the gate closes.

8 Decay slider

After the hold time passes, this setting determines how quickly the gate closes. The value

here is expressed as the time required for the level to change by 6 dB.

9 GR (gain reduction) meter

Displays the amount by which the signal's gain is reduced.

0 OUT (gate output) meter

Displays the gate output level.

GATE screen menu

Press the Menu key ( ) from the GATE screen to display the following options.

Setting the gate

1. Display the GATE screen. (page 5)

2. Turn on the gate and then touch the slider that you want to adjust.

3. Use the [TOUCH AND TURN] knob to adjust the setting.

Refer to the gate graph and each meter while making adjustments.

You can also drag the slider on the touchscreen to adjust the setting.

1 Copy

Copies the GATE parameters of the selected

channel to the clipboard.

2 Paste

Pastes the GATE parameters in the clipboard to the

selected channel.

3 Compare

Allows you to compare the GATE parameters of the

selected channel with the GATE parameters in the

clipboard by switching between the two.

4 Default

Resets the GATE settings for the current channel to

their default values.

Configuration screens

Reference Manual

TF series

COMP screen

Allows you to configure the compressor for each channel. You can adjust settings using 1-

knob mode, which allows you to use the [TOUCH AND TURN] knob to easily adjust settings,

or manual mode, which allows you to adjust each parameter individually.

1 COMP button

Turns the compressor on and off.

2 1-knob button

Switches between 1-knob mode and manual mode.

3 1-knob level slider (1-knob mode only)

Adjusts the amount of 1-knob COMP applied.

Not displayed during manual mode.

4 Compressor input level slider

Displays the compressor output level.

5 Threshold slider

Determines the level at which compression is applied.

6 Compressor graph

Displays a visual representation of the current settings.

7 Ratio slider

Determines the amount of compression that is applied.

8 Attack slider

When the input signal exceeds the threshold, this setting determines how quickly the

maximum amount of compression is applied.

9 Release slider

When the input signal drops below the threshold, this setting determines how much

time passes before compression is no longer applied. The value here is expressed as the

time required for the level to change by 6 dB.

0 Out Gain slider

Adjusts the output level.

A Knee button

Determines how gradual or sudden the curve is at the threshold. A soft knee means that

compression is applied gradually as the signal exceeds the threshold; a hard knee means

a more sudden transition.

B GR (gain reduction) meter

Displays the amount by which the signal's gain is reduced.

C OUT (compressor output) meter

Displays the compressor output level.

How does 1-knob COMP mode work?

1-knob COMP mode allows you to adjust the amount of compression applied to the signal with

just the turn of a knob.

By turning the [TOUCH AND TURN] knob to the right (or sliding the 1-knob level slider to the

right), more compression is applied. In situations where raising the fader or gain could cause

clipping at louder points in the signal, compression can deliver a more consistent sound.

1-knob COMP takes some of the worry out of compression by allowing you to adjust the

balance between threshold, ratio, and out gain easily.

ոչ

ջպն

յմ

Configuration screens

Reference Manual

TF series

COMP screen menu

Press the Menu key ( ) from the COMP screen to display the following options.

Setting the compressor

1. Display the COMP screen. (page 5)

2. If the compressor is turned off, touch the COMP button

to turn compression on.

3. Touch the 1-knob button and turn 1-knob COMP mode off.

4. Adjust the desired slider.

Drag the sliders to adjust each parameter.

When you touch an item, you can also use the [TOUCH AND TURN] knob to adjust the setting.

Adjusting the compressor in 1-knob COMP mode

1. Turn 1-knob COMP mode on.

2. Turn the [TOUCH AND TURN] knob.

Attack, Release, and Knee settings are fixed at their current settings, and the Threshold, Ratio, and

Out Gain settings are adjusted automatically.

1 Copy

Copies the COMP parameters of the selected

channel to the clipboard.

2 Paste

Pastes the COMP parameters in the clipboard to

the selected channel.

3 Compare

Allows you to compare the COMP parameters of

the selected channel with the COMP parameters

in the clipboard by switching between the two.

4 Default

Resets the COMP settings for the current channel

to their default values.

Configuration screens

Reference Manual

TF series

FX screen (FX1/2, InsFX1–6)

Allows you to select an effect and edit its parameters.

1 Send button

Displayed for CH 1–40, ST IN 1 and ST IN 2.

Determines whether a signal is sent (on) or not sent (off) to the FX return channel.

2 EFFECT TYPE button

Displays the EFFECT TYPE screen (page 68), where you can select an effect type.

3 Effect type and name

Displays the type and name of the current effect.

4 R Safe (recall safe) indicator

Displays the recall safe status of the effects module.

Displays the RECALL SAFE screen. (page 38)

5 M safe (mute safe) button

Turns mute safe on and off for the effects module.

6 FX send level slider

Displayed for CH 1–40, ST IN 1 and ST IN 2.

Allows you to adjust the amount of signal that is sent to the effects module.

7 Pre button

Displayed for CH 1–40, ST IN 1 and ST IN 2.

Allows you to select whether the pre-fader or post-fader signal is processed by the effect

module.

On: Before the fader

Off: After the fader

8 Parameter selection buttons

Touch to display other parameters available for the current effect.

9 Parameter sliders

Allow you to adjust the parameters available for the current effect.

0 Sync button

Displayed for effects that have a tempo setting, such as delays. When this button is

turned on, the effect's tempo setting can be controlled with the [TAP] button found in

the SENDS ON FADER section of the top panel.

A Bypass button

Allows you to bypass the effects module.

B Effects output level meter

Displays the effects output level.

C CUE button

Turns cue on and off for the effects module.

ձղ ճ մ ջպյ

չոնշ

Configuration screens

Reference Manual

TF series

FX screen menu

Press the Menu key ( ) from the FX screen to display the following options.

EFFECT TYPE screen

Allows you to select the effect type. Touch the desired button to make a selection.

Setting an effect

1. Touch the effects type button.

When the EFFECTS TYPE screen is displayed, select the

desired effect type.

2. Touch the Send button.

3. Adjust the parameter sliders as desired.

You can adjust the characteristics of the effect, the wet/dry

balance, etc.

4. Adjust the effects send level slider.

This allows you to adjust how much of the channel's signal

is sent to the effects module.

5. Adjust the FX RTN1/2 levels.

FX RTN1/2 channels are in the INPUT FADER BANK. (Stereo Channelspage 47)

Setting an insert effect

You can configure insert effects for AUX9/10–AUX19/20.

1. Touch the effects type button.

When the EFFECTS TYPE screen is displayed, select the desired effect type.

2. Touch the bypass button.

Bypass is turned on by default; turn the bypass off.

3. Adjust the parameter sliders as desired.

Adjust the characteristics of the effect.

Send button

FX send level slider

1 Copy

Copies the effect parameters of the selected effect

to the clipboard.

2 Paste

Pastes the effect parameters in the clipboard to the

selected effect.

3 Compare

Allows you to compare the effect parameters of

the selected effect with the effect parameters in

the clipboard by switching between the two.

4 Default

Resets the selected effect's settings to their default

values.

Configuration screens

Reference Manual

TF series

Effect parameters

REVERB HALL, REVERB ROOM, REVERB STAGE, REVERB PLATE

One-input, two-output hall, room, stage, and plate reverbs.

MONO DELAY

One-input, two-output basic repeating-type delay.

STEREO DELAY

Two-input, two-output basic stereo delay.

DELAY LCR

One-input, two-output 3-tap delay.

ECHO

Two-input, two-output stereo delay with a crossed feedback loop.

Parameter Range Description

Reverb Time 0.3s–20.0s Determines the length of the reverberation.

Initial Delay 1.0ms–500.0ms

Determines the amount of time that passes before the initial

reverberation is heard.

High Ratio 0.1–1.0 Ratio of high frequency reverberations to the Reverb Time.

Diffusion 0–10 Left and right spread of the reverberation.

Density 0% – 100% Density of the reverberation.

HPF Thru, 21.2Hz–8.00kHz High-pass filter cutoff frequency.

LPF 50.0Hz–16.0kHz, Thru Low-pass filter cutoff frequency.

Parameter Range Description

Delay 1.0ms–2700.0ms Delay time.

Feedback Gain -99 – +99 Amount of feedback.

High Ratio 0.1–1.0 Amount of high-frequency feedback.

HPF Thru, 21.2Hz–8.00kHz High-pass filter cutoff frequency.

LPF 50.0Hz–16.0kHz, Thru Low-pass filter cutoff frequency.

Sync Off, On Delay time tempo sync.

Note ----, ~ Value used to calculate the delay time based on the tempo.

Parameter Range Description

Delay L 1.0ms–1350.0ms Left channel delay time.

Delay R 1.0ms–1350.0ms Right channel delay time.

Feedback Gain L -99 – +99 Left channel feedback gain.

Feedback Gain R -99 – +99 Right channel feedback gain.

High Ratio 0.1–1.0 Amount of high-frequency feedback.

HPF Thru, 21.2Hz–8.00kHz High-pass filter cutoff frequency.

LPF 50.0Hz–16.0kHz, Thru Low-pass filter cutoff frequency.

Sync Off, On Delay time tempo sync.

Note L

----, ~

Value used to calculate the left channel delay time based on the

tempo.

Note R

----, ~

Value used to calculate the right channel delay time based on

the tempo.

Parameter Range Description

Delay L 1.0ms–2700.0ms Left channel delay time.

Delay C 1.0ms–2700.0ms Center channel delay time.

Delay R 1.0ms–2700.0ms Right channel delay time.

Delay FB 1.0ms–2700.0ms Feedback delay time.

Feedback Gain -99 – +99 Amount of feedback.

High Ratio 0.1–1.0 Amount of high-frequency feedback.

HPF Thru, 21.2Hz–8.00kHz High-pass filter cutoff frequency.

LPF 50.0Hz–16.0kHz, Thru Low-pass filter cutoff frequency.

Level L -100 – +100 Left channel level.

Level C -100 – +100 Center channel level.

Level R -100 – +100 Right channel level.

Sync Off, On Delay time tempo sync.

Note L

----, ~

Value used to calculate the left channel delay time based on the

tempo.

Note C

----, ~

Value used to calculate the center channel delay time based on

the tempo.

Note R

----, ~

Value used to calculate the right channel delay time based on

the tempo.

Note FB

----, ~

Value used to calculate the delay feedback time based on the

tempo.

Parameter Range Description

Delay L 1.0ms–1350.0ms Left channel delay time.

Delay R 1.0ms–1350.0ms Right channel delay time.

Delay FB L 1.0ms–1350.0ms Left channel feedback delay time.

Delay FB R 1.0ms–1350.0ms Right channel feedback delay time.

Feedback Gain L -99 – +99 Left channel feedback gain.

Feedback Gain R -99 – +99 Right channel feedback gain.

XFeedback Gain -99 – +99 Left-to-right, right-to-left feedback gain.

High Ratio 0.1–1.0 Amount of high-frequency feedback.

HPF Thru, 21.2Hz–8.00kHz High-pass filter cutoff frequency.

LPF 50.0Hz–16.0kHz, Thru Low-pass filter cutoff frequency.

Sync Off, On Delay time tempo sync.

Note L

----, ~

Value used to calculate the left channel delay time based on the

tempo.

Note R

----, ~

Value used to calculate the right channel delay time based on

the tempo.

Note FBL

----, ~

Value used to calculate the left channel feedback delay time

based on the tempo.

Note FBR

----, ~

Value used to calculate the right channel feedback delay time

based on the tempo.

Configuration screens

Reference Manual

TF series

DELAY-REVERB (V1.1 and later)

One-input, two-output effect that has a delay and reverb connected in series.

EARLY REF (V1.1 and later)

One-input, two-output early reflection effect.

GATE REVERB, REVERSE GATE (V1.1 and later)

One-input, two-output early reflection with gate, and an early reflection with reverse gate.

CHORUS (V1.1 and later)

Two-input, two-output chorus effect.

FLANGE (V1.1 and later)

Two-input, two-output flanger effect.

Parameter Range Description

Delay 1.0ms - 2700.0ms Delay time.

Feedback Gain -99% - 99% Amount of feedback.

DLY BAL 0% - 100% Delay mix balance.

Reverb Time 0.3s - 20.0s Determines the length of the reverberation.

High Ratio 0.1 - 1.0 Ratio of high frequency reverberations to the Reverb Time.

Diffusion 0 - 10 Left and right spread of the reverberation.

Density 0% - 100% Density of the reverberation.

HPF Thru, 21.2Hz - 8.00kHz High-pass filter cutoff frequency.

LPF 50.0Hz - 16.0kHz, Thru Low-pass filter cutoff frequency.

REV BAL 0% - 100% Reverb mix balance.

Sync Off, On Parameter tempo sync.

Note

----, ~

Value used to calculate the delay time based on the tempo.

Parameter Range Description

Type

S-Hall, L-Hall, Random,

Reverse, Plate, Spring

Early reflection type.

Room Size 0.1 - 20.0 Room size; determines interval between early reflections.

Liveness 0 - 10 Decay of the early reflections (0: dead, 10: live).

Initial Delay 1.0ms - 500.0ms Delay before the early reflection.

Diffusion 0 - 10 Width of the reflections in the stereo field.

Density 0% - 100% Density of the reflections.

ER Number 1 - 19 Number of reflections.

Feedback Gain -99% - 99% Amount of feedback.

High Ratio 0.1 - 1.0 Amount of high-frequency feedback.

HPF Thru, 21.2Hz - 8.00kHz High-pass filter cutoff frequency.

LPF 50.0Hz - 16.0kHz, Thru Low-pass filter cutoff frequency.

Parameter Range Description

Type Type-A, Type-B Early reflection type.

Room Size 0.1 - 20.0 Room size; determines interval between early reflections.

Liveness 0 - 10 Decay of the early reflections.

Initial Delay 1.0ms - 500.0ms Delay before the early reflection.

Diffusion 0 - 10 Width of the reflections in the stereo field.

Density 0% - 100% Density of the reflections.

ER Number 1 - 19 Number of reflections.

Feedback Gain -99% - 99% Amount of feedback.

High Ratio 0.1 - 1.0 Amount of high-frequency feedback.

HPF Thru, 21.2Hz - 8.00kHz High-pass filter cutoff frequency.

LPF 50.0Hz - 16.0kHz, Thru Low-pass filter cutoff frequency.

Parameter Range Description

Frequency 0.05Hz - 10.00Hz Modulation speed

AM Depth 0% - 100% Depth of amplitude modulation.

PM Depth 0% - 100% Depth of pitch modulation.

MOD. Delay 1.0ms - 500.0ms Delay time of modulation.

Sync Off, On Parameter tempo sync.

Note

Value used to calculate the frequency based on the tempo.

Parameter Range Description

Frequency 0.05Hz - 10.00Hz Modulation speed

Depth 0% - 100% Depth of modulation.

MOD. Delay 1.0ms - 500.0ms Delay time of modulation.

Feedback Gain -99% - 99% Amount of feedback.

Sync Off, On Parameter tempo sync.

Note

Value used to calculate the frequency based on the tempo.

Configuration screens

Reference Manual

TF series

SYMPHONIC (V1.1 and later)

Two-input, two-output symphonic effect.

PHASER (V1.1 and later)

Two-input, two-output 16-stage phase-shift effect.

M BAND COMP (V1.1 and later)

Two-input, two-output three-band compressor. Each band has solo and gain reduction

metering.

Parameter Range Description

Frequency 0.05Hz - 10.00Hz Modulation speed

Depth 0% - 100% Depth of modulation.

MOD. Delay 1.0ms - 500.0ms Delay time of modulation.

Sync Off, On Parameter tempo sync.

Note

Value used to calculate the frequency based on the tempo.

Parameter Range Description

Frequency 0.05Hz - 10.00Hz Modulation speed

Depth 0% - 100% Depth of modulation.

Feedback Gain -99% - 99% Amount of feedback.

Offset 0 - 100 Offset of the phase shifted frequency.

Phase 0° - 355° Left/right balance of modulation.

Stage 2 - 16 Number of phase shift stages.

HPF Thru, 21.2Hz - 8.00kHz High-pass filter cutoff frequency.

LPF 50.0Hz - 16.0kHz, Thru Low-pass filter cutoff frequency.

Sync Off, On Parameter tempo sync.

Note

Value used to calculate the frequency based on the tempo.

Parameter Range Description

Low Gain -12.0dB - +12.0dB Low-band gain.

Mid Gain -12.0dB - +12.0dB Mid-band gain.

High Gain -12.0dB - +12.0dB High-band gain.

Total Gain -72dB - +12dB Overall gain.

L-M XOver 21.2Hz - 8.00kHz Low-to-mid crossover frequency.

M-H XOver 21.2Hz - 8.00kHz Mid-to-high crossover frequency.

Knee 0 - 5 Compressor knee (all bands).

Low/Mid/High Link Off, On

When turned on, the difference in the threshold for low, mid,

and high is maintained. (V3.0 and later)

Low Thr -54dB - 0dB Low threshold.

Low Ratio 1:1 - ∞:1 Low ratio.

Low Attack 0ms - 120ms Low attack time.

Low Release 3.34ms - 42.7s Low release time.

Low Bypass Off, On Compression bypass feature for low.

Low Solo Off, On Solo feature for low.

Mid Thr -54dB - 0dB Mid threshold.

Mid Ratio 1:1 - ∞:1 Mid ratio.

Mid Attack 0ms - 120ms Mid attack time.

Mid Release 3.34ms - 42.7s Mid release time.

Mid Bypass Off, On Compression bypass feature for mid.

Mid Solo Off, On Solo feature for mid.

High Thr -54dB - 0dB High threshold.

High Ratio 1:1 - ∞:1 High Ratio

High Attack 0ms - 120ms High attack time.

High Release 3.34ms - 42.7s High release time.

High Bypass Off, On Compression bypass feature for high.

High Solo Off, On Solo feature for high.

NOTE

The Make Up parameter is omitted for V3.0 and later.

Configuration screens

Reference Manual

TF series

PING PONG DELAY (V2.0 and later)

One-input, two-output ping pong delay. The delayed sound alternates between left and right

at equal intervals.

DUAL PITCH (V2.0 and later)

Two-input, two-output pitch-shift effect.

OUTPUT DELAY (V2.5 and later)

Two-input, two-output single delay. When used for INS FX 1–6, this delay is good for delay

compensation.

*1 frame rate=24: 0.03 - 24.00,

frame rate=25: 0.03 - 25.00,

frame rate=29.97D/29.97: 0.03 - 29.97

frame rate=30D/30: 0.03 - 30.00

Set the frame rate in "Frame Rate", on the "Others" section (page 26) of the PREFERENCE screen.

Parameter Range Description

Delay 1.0ms - 1350.0ms Delay time.

Feedback Gain -99% - 99% Amount of feedback.

High Ratio 0.1 - 1.0 Amount of high-frequency feedback.

HPF Thru, 21.2Hz - 8.00kHz High-pass filter cutoff frequency.

LPF 50.0Hz - 16.0kHz, Thru Low-pass filter cutoff frequency.

Sync Off, On Parameter tempo sync.

Note ----, - Value used to calculate the delay time based on the tempo.

Parameter Range Description

Pitch 1 -24 - 24 Pitch of Ch1 (semitone increments).

Fine 1 -50 - 50 Pitch of Ch1 (1 cent increments).

Level 1 -100 - 100 Volume of Ch1.

Pan 1 L63 - R63 Pan of Ch1.

Delay 1 1.0ms - 1000.0ms Delay time of Ch1.

Feedback Gain 1 -99 - 99 Feedback level of Ch1.

Pitch 2 -24 - 24 Pitch of Ch2 (semitone increments).

Fine 2 -50 - 50 Pitch of Ch2 (1 cent increments).

Level 2 -100 - 100 Volume of Ch2.

Pan 2 L63 - R63 Pan of Ch2.

Delay 2 1.0ms - 1000.0ms Delay time of Ch2.

Feedback Gain 2 -99 - 99 Feedback level of Ch2.

Mode 1 - 10 Width of pitch shift.

Sync Off, On Parameter tempo sync.

Note 1 ----, - Value used to calculate Delay 1 based on the tempo.

Note 2 ----, - Value used to calculate Delay 2 based on the tempo.

Parameter Range Description

LR LINK On, Off Links the left and right delays.

Delay

0.3 – 343.6 meter

1.1 – 1127.3 feet

1.00 – 1000.00ms

0.03 – 30.00 frame

Delay time is set in units of frames (V3.5 and later), meters, feet,

or ms (milliseconds).

Configuration screens

Reference Manual

TF series

SEND TO AUX screen

Allows you to configure the amount of signal that is sent from each channel to the AUX buses.

You can swipe left and right to view other buses.

1 Send button

Determines whether a signal is sent (on) or not sent (off) to the corresponding AUX bus.

2 Send level slider

Determines the amount of signal sent to the corresponding AUX bus.

3 Pre button

Selects whether to send the signal to the AUX channel from before the fader, or from

after the fader.

On: Before fader

Off: After fader

When this is on, you can select whether to send the signal directly before the EQ or

directly before the fader, from "Pre Fader Send Point" on the BUS SETUP screen

(page 33).

4 Send pan slider

Displayed for stereo AUX buses. Allows you to adjust the pan of the signal sent to the

corresponding AUX bus.

Adjusting the SEND TO AUX level

1. Adjust the level sliders as desired.

Each level slider determines the amount of signal sent from

the selected channel to the corresponding AUX bus.

2. Turn the Pre button on or off depending on your

needs.

Send the pre-fader signal when using the AUX bus for on-stage floor monitors—this allows you to

create a mix that is separate from the main mix.

Send the post-fader signal when using external effects processors or when you want to maintain the

same mix balance as the main mix.

3. Turn the send button on or off.

When turned on, the signal is sent to the corresponding AUX

bus.

4. Touch the send pan slider and then adjust it using the [TOUCH AND TURN] knob.

When sending the signal to a stereo AUX bus, you can adjust the pan of the signal that is sent.

Configuration screens

Reference Manual

TF series

ASSIGN screen

Allows you configure recall safe and mute safe settings, DCA group assignments, signals sent

to the SUB bus, etc.

1 Recall Safe button

Turns Recall Safe on and off for the corresponding channel.

You can display the RECALL SAFE screen by touching the jump button in the right corner

of the Recall Safe button. (page 38)

2 Mute Safe button

You can temporarily exclude certain channels from a mute group.

If you mute a mute group, any channels in that group that have mute safe enabled will

not be muted.

3 ST button

Turns the channel's assignment to the stereo channel on and off.

4 SUB button

Determines whether the channel's signal is sent (on) or not sent (off) to the SUB bus.

5 SUB level slider

Determines the amount of signal sent from the selected channel to the SUB bus.

6 DCA buttons

Turns the channel's assignment to each DCA group (1–8) on and off.

You can assign a channel to multiple DCA groups if desired.

7 Mute buttons (V4.0 and later)

Turns the channel's assignment to mute groups 3–6 on and off.

You can assign a channel to multiple mute groups if desired.

You cannot change the assignments for MUTE1 INPUT and MUTE2 FX.

AUTOMIXER screen (V3.5 and later)

Sets the AUTOMIXER that can be used for CH1–CH8.

About the AUTOMIXER

The AUTOMIXER is a function for automating the sound mixing of conversation heard in

conferences, talk shows and so on. This function detects mics that are enabled and

automatically optimizes the gain distribution to maintain a consistent system gain with multiple

mics, eliminating the need for the engineer to keep watching the fader levels.

How the AUTOMIXER works

The TF series AUTOMIXER uses the Dugan speech system, which automatically adjusts the

gain of up to 8 mics.

Unlike limiters or auto-level controllers, the Dugan speech system lets the engineer control

individual levels as usual, even when more than one person is talking at the same time. Also,

the audio on the mics is detected and the gain is automatically distributed when no one is

talking, so the faders can be left up.

ձղ ճ

When one person speaks,

while using multiple mics

When two people speak,

while using multiple mics

When one person talks, the gain on that mic

instantly rises, and the gain on other mics is

lowered. This works the same when another

person speaks.

When two people talk at the same time, the gain

between the two mics is automatically distributed

to provide a uniform total gain, and the gain on the

remaining mic is lowered.

NOTE

• The AUTOMIXER is placed directly after the channel ON for CH1–CH8.

• When the Pre button for SEND TO AUX on CH1–CH8 is off, signal is sent from directly after the

AUTOMIXER to the AUX bus.

• When CH1–CH8 are stereo linked together, the AUTOMIXER parameters will not be linked.

Mic input

audio (dB)

Automix gain

(dB)

Mic input

audio (dB)

Automix gain

(dB)

Configuration screens

Reference Manual

TF series

1 AUTOMIXER ON button

Turns the AUTOMIXER on/off for the respective channel.

2 Level indicator

Use this indicator to check whether the input gain going into the AUTOMIXER is

appropriate.

Off: No input signal, or not enough input level

Lighted green: Input gain is appropriate

Lighted red: Overload input

3 Automix gain meter

Displays the gain that was adjusted using the AUTOMIXER.

4 Weight indicator

Displays the value that was set in the

5 Weight text box as a bar graph.

5 Weight text box

Adjusts the signal level inputted into the AUTOMIXER side chain. When this is set to the

same value as other channels, the gain of audio signals that are inputted at the same

time will be equally distributed. When this value is increased, the gain of audio signals

that are inputted at the same time will be distributed to create a louder sound compared

with other channels.

Setting range: -100.0 dB, -29.5 dB–0.0 dB (default setting)–15.0 dB

6 Group selection button

Selects whether to assign either AUTOMIXER group a or b. You can use groups to

independently create two types of mixes. The background color changes according to

the group selected.

7 Group Bypass a/b buttons (V4.0 and later)

Turns the Automixer function bypass on/off for each group.

NOTE

We recommend that you leave the AUTOMIXER off for audio that does not contain speech

components, such as live concerts.

NOTE

Adjust the input gain using the analog gain, digital gain and faders for each input channel.

Setting the AUTOMIXER

1. Display the AUTOMIXER screen for CH1–CH8.

2. Turn the channel on that will be inputted into the

AUTOMIXER.

3. Touch the group selection button to select the

group to which each channel is assigned.

4. Adjust the input level for each channel using the

analog gain and faders, so that the level indicators are green.

5. Touch the weight setting boxes for each channel; and with the focus set on the box,

turn the [TOUCH AND TURN] knob to adjust the relative sensitivity between

channels.

6. Adjust the weight further as necessary while inputting audio, in order to balance the

sound between the channels.

Configuration screens

Reference Manual

TF series

CH VIEW screen

Provides an overview of all the settings for a channel.

You can change settings using this screen, in addition to the corresponding feature's

configuration screen.

Items displayed on this screen vary depending on the type of channel selected.

CH1–CH32

1 Channel name

Touch to display the CH NAME screen.

Touch to display information for a different channel.

2 Recall Safe button

Turns recall safe on and off for the corresponding channel.

You can display the RECALL SAFE screen (page 38) by touching the jump button in

the right corner of the Recall Safe button.

3 Input source indicator

Displays the input channel's input source. You can select the input source on the INPUT

screen.

4 Mute Safe button

Touch to temporarily exclude the selected channel from the input mute group.

If you mute the input mute group, any channels in that group that have mute safe

enabled will not be muted.

5 Boxes

Touch to display the configuration screen for the corresponding feature.

You can touch the EQ, GATE, and COMP buttons displayed here to turn the

corresponding feature on and off.

HA box: Displays the INPUT screen. (page 57)

EQ box: Displays the EQ screen. (page 59)

GATE box: Displays the GATE screen. (page 63)

COMP box: Displays the COMP screen. (page 65)

AUTOMIXER box (V3.5 and later): Displays the AUTOMIXER screen. (page 74)

6 Channel on/off button

Turns the selected channel on and off.

7 PAN slider

Adjusts the pan for the selected channel.

8 FX1/FX2 boxes

Displays the effect type.

When selected, you can use the [TOUCH AND TURN] knob to adjust the effects send

level. You can also display the corresponding effect's configuration screen by touching

again.

Each box displays the amount of signal from the selected channel that is sent to the

corresponding effects module.

Send level, the selected channel's fader level, and the actual send level grouped with the

DCA is displayed in the triangular bar.

Displays whether the signal sent to the FX1/2 return channel is from directly before the

fader, or directly after the fader. If the indicator lights green, the signal is directly before

(pre-fader); and if the indicator is off, the signal is directly after (post-fader).

9 SEND TO AUX box

Touch when selected to display the SEND TO AUX screen.

Displays the amount of signal from the selected channel that is sent to each AUX bus.

Send level, the selected channel's fader level, and the actual send level grouped with the

DCA is displayed in the horizontal bar.

The information displayed here indicates whether the signal sent to the AUX bus is the

pre-fader or post-fader signal. Pre-fader signal is displayed in green; post-fader signal is

displayed in gray.

0 ASSIGN box

Displays the ASSIGN screen. (page 74)

A Channel output level slider

Adjusts the fader level for the selected channel.

B Channel output level meter

Displays the channel's output signal level.

ջռսվտ

յղմ նշո

Configuration screens

Reference Manual

TF series

C Direct out port indicator

Indicates the channel's direct out port.

For information about channels and output ports, see "Quick Config Input and input

channel relationships" (page 106).

D Direct out point button

Allows you to set the point of the direct out signal.

Pre DG: Before the digital gain

Pre HPF: Before the high-pass filter

Pre Fader: Before the fader

Post ON: directly after the [ON] key; CH1–CH8 are directly after the AUTOMIXER

E Direct out on/off button

Turns the direct out on and off.

CH33–CH40

1 Channel name

Touch to display the CH NAME screen.

Touch to display information for a different channel.

2 Recall Safe button

Turns recall safe on and off for the corresponding channel.

You can display the RECALL SAFE screen (page 38) by touching the jump button in

the right corner of the Recall Safe button.

3 Input source indicator

Displays the input channel's input source. You can select the input source on the INPUT

screen.

4 Mute Safe button

Touch to temporarily exclude the selected channel from the input mute group.

If you mute the input mute group, any channels in that group that have mute safe

enabled will not be muted.

5 Boxes

Touch to display the configuration screen for the corresponding feature.

You can touch the EQ button displayed here to turn EQ on and off.

HA box: Displays the INPUT screen. (page 57)

EQ box: Displays the EQ screen. (page 59)

6 Channel on/off button

Turns the selected channel on and off.

7 PAN slider

Adjusts the pan for the selected channel.

8 FX1/FX2 boxes

Displays the effect type.

When selected, you can use the [TOUCH AND TURN] knob to adjust the effects send

level. You can also display the corresponding effect's configuration screen by touching

again.

Each box displays the amount of signal from the selected channel that is sent to the

corresponding effects module.

Send level, the selected channel's fader level, and the actual send level grouped with the

DCA is displayed in the triangular bar.

Displays whether the signal sent to the FX1/2 return channel is from directly before the

fader, or directly after the fader. If the indicator lights green, the signal is directly before

(pre-fader); and if the indicator is off, the signal is directly after (post-fader).

9 SEND TO AUX box

Touch when selected to display the SEND TO AUX screen.

Displays the amount of signal from the selected channel that is sent to each AUX bus.

Send level, the selected channel's fader level, and the actual send level grouped with the

DCA is displayed in the horizontal bar.

ձղմ նշո

ջռյճ

Configuration screens

Reference Manual

TF series

The information displayed here indicates whether the signal sent to the AUX bus is the

pre-fader or post-fader signal. Pre-fader signal is displayed in green; post-fader signal is

displayed in gray.

0 ASSIGN box

Displays the ASSIGN screen. (page 74)

A Channel output level slider

Adjusts the fader level for the selected channel.

B Channel output level meter

Displays the channel's output signal level.

ST IN 1L-ST IN 2R

1 Channel name

Touch to display the CH NAME screen.

Touch to display information for a different channel.

2 Recall Safe button

Turns recall safe on and off for the corresponding channel.

You can display the RECALL SAFE screen (page 38) by touching the jump button in

the right corner of the Recall Safe button.

3 Input source indicator

Displays the input channel's input source. You can select the input source on the INPUT

screen.

4 Mute Safe button

Touch to temporarily exclude the selected channel from the input mute group.

If you mute the input mute group, any channels in that group that have mute safe

enabled will not be muted.

5 Boxes

Touch to display the configuration screen for the corresponding feature.

You can touch the EQ button displayed here to turn EQ on and off.

HA box: Displays the INPUT screen. (page 57)

EQ box: Displays the EQ screen. (page 59)

DELAY box (V4.0 or later): Displays the DELAY screen. (page 92)

6 Channel on/off button

Turns the selected channel on and off.

7 BAL (balance) slider

Adjusts the left/right volume balance for the channel.

8 FX1/FX2 boxes

Displays the effect type.

When selected, you can use the [TOUCH AND TURN] knob to adjust the effects send

level. You can also display the corresponding effect's configuration screen by touching

again.

Each box displays the amount of signal from the selected channel that is sent to the

corresponding effects module.

Send level, the selected channel's fader level, and the actual send level grouped with the

DCA is displayed in the triangular bar.

Displays whether the signal sent to the FX1/2 return channel is from directly before the

fader, or directly after the fader. If the indicator lights green, the signal is directly before

(pre-fader); and if the indicator is off, the signal is directly after (post-fader).

9 SEND TO AUX box

Touch when selected to display the SEND TO AUX screen.

Displays the amount of signal from the selected channel that is sent to each AUX bus.

Send level, the selected channel's fader level, and the actual send level grouped with the

DCA is displayed in the horizontal bar.

The information displayed here indicates whether the signal sent to the AUX bus is the

pre-fader or post-fader signal. Pre-fader signal is displayed in green; post-fader signal is

displayed in gray.

0 ASSIGN box

Displays the ASSIGN screen. (page 74)

A Channel output level slider

Adjusts the fader level for the selected channel.

ձղ մնշո

ջռյճ

Configuration screens

Reference Manual

TF series

B Channel output level meter

Displays the channel's output signal level.

FX1L–FX2R

1 Channel name

Touch to display the CH NAME screen.

Touch to display information for a different channel.

2 Recall Safe button

Turns recall safe on and off for the corresponding channel.

You can display the RECALL SAFE screen (page 38) by touching the jump button in

the right corner of the Recall Safe button.

3 Mute Safe button

Touch to temporarily exclude the selected channel from the effects mute group.

If you mute the effects mute group, any channels in that group that have mute safe

enabled will not be muted.

4 Boxes

Touch to display the configuration screen for the corresponding feature.

You can touch the EQ button displayed here to turn EQ on and off.

FROM box: Displays the SEND FROM screen. (page 88) (V3.0 and later)

FX1 (FX2) box: Displays the FX screen. (page 67)

EQ box: Displays the EQ screen. (page 59)

5 Channel on/off button

Turns the selected channel on and off.

6 BAL (balance) slider

Adjusts the left/right volume balance for the channel.

7 SEND TO AUX box

Touch when selected to display the SEND TO AUX screen.

Displays the amount of signal from the selected channel that is sent to each AUX bus.

Send level, the selected channel's fader level, and the actual send level grouped with the

DCA is displayed in the horizontal bar.

The information displayed here indicates whether the signal sent to the AUX bus is the

pre-fader or post-fader signal. Pre-fader signal is displayed in green; post-fader signal is

displayed in gray.

8 ASSIGN box

Displays the ASSIGN screen. (page 74)

9 Channel output level slider

Adjusts the fader level for the selected channel.

0 Channel output level meter

Displays the channel's output signal level.

DCA 1–DCA 8

ձղ ճյն

չպմ

ղճ

Configuration screens

Reference Manual

TF series

1 Channel name

Touch to display the CH NAME screen.

Touch to display information for a different channel.

2 Recall Safe button

Turns recall safe on and off for the corresponding channel.

You can display the RECALL SAFE screen (page 38) by touching the jump button in

the right corner of the Recall Safe button.

3 Channel on/off button

Turns the selected channel on and off.

4 Channel output level slider

Adjusts the fader level for the selected channel.

5 ASSIGN box (V1.1 and later)

When this area is selected, touch this area to display the DCA ASSIGN screen.

(page 90)

AUX1–AUX8

1 Channel name

Touch to display the CH NAME screen.

Touch to display information for a different channel.

2 Recall Safe button

Turns recall safe on and off for the corresponding channel.

You can display the RECALL SAFE screen (page 38) by touching the jump button in

the right corner of the Recall Safe button.

3 Boxes

Touch to display the configuration screen for the corresponding feature.

You can touch the EQ, GEQ, and COMP buttons displayed here to turn the

corresponding feature on and off.

FROM box: Displays the SEND FROM screen. (page 88)

EQ box: Displays the EQ screen. (page 59)

GEQ box: Displays the GEQ screen. (page 85)

COMP box: Displays the COMP screen. (page 65)

4 Channel on/off button

Turns the selected channel on and off.

5 OUTPUT box

Displays the OUTPUT screen. (page 87)

6 Channel output level slider

Adjusts the fader level for the selected channel.

7 Channel output level meter

Displays the channel's output signal level.

AUX 9–AUX 20

ձղ մյ

նշ

ձղ մնյ

շո

Configuration screens

Reference Manual

TF series

1 Channel name

Touch to display the CH NAME screen.

Touch to display information for a different channel.

2 Recall Safe button

Turns recall safe on and off for the corresponding channel.

You can display the RECALL SAFE screen (page 38) by touching the jump button in

the right corner of the Recall Safe button.

3 Boxes

Touch to display the configuration screen for the corresponding feature.

You can touch the EQ and COMP buttons displayed here to turn the corresponding

feature on and off.

FROM box: Displays the SEND FROM screen. (page 88)

EQ box: Displays the EQ screen. (page 59)

COMP box: Displays the COMP screen. (page 65)

InsFX box: Displays the FX screen. (page 67)

4 Channel on/off button

Turns the selected channel on and off.

5 BAL (balance) slider

Adjusts the left/right volume balance for the channel.

6 OUTPUT box

Displays the OUTPUT screen. (page 87)

7 Channel output level slider

Adjusts the fader level for the selected channel.

8 Channel output level meter

Displays the channel's output signal level.

SUB

1 Channel name

Touch to display the CH NAME screen.

Touch to display information for a different channel.

2 Recall Safe button

Turns recall safe on and off for the corresponding channel.

You can display the RECALL SAFE screen (page 38) by touching the jump button in

the right corner of the Recall Safe button.

3 Boxes

Touch to display the configuration screen for the corresponding feature.

You can touch the EQ and COMP buttons displayed here to turn the corresponding

feature on and off.

FROM box: Displays the SEND FROM screen. (page 88)

EQ box: Displays the EQ screen. (page 59)

COMP box: Displays the COMP screen. (page 65)

4 Channel on/off button

Turns the selected channel on and off.

5 OUTPUT box

Displays the OUTPUT screen. (page 87)

6 Channel output level slider

Adjusts the fader level for the selected channel.

ձղ մյճ

նշ

Configuration screens

Reference Manual

TF series

7 Channel output level meter

Displays the channel's output signal level.

ST L, ST R

1 Channel name

Touch to display the CH NAME screen.

Touch to display information for a different channel.

2 Recall Safe button

Turns recall safe on and off for the corresponding channel.

You can display the RECALL SAFE screen (page 38) by touching the jump button in

the right corner of the Recall Safe button.

3 Boxes

Touch to display the configuration screen for the corresponding feature.

You can touch the EQ, GEQ, and COMP buttons displayed here to turn the

corresponding feature on and off.

EQ box: Displays the EQ screen. (page 59)

GEQ box: Displays the GEQ screen. (page 85)

COMP box: Displays the COMP screen. (page 65)

4 Channel on/off button

Turns the selected channel on and off.

5 BAL (balance) slider

Adjusts the left/right volume balance for the channel.

6 OUTPUT box

Displays the OUTPUT screen. (page 87)

7 Channel output level slider

Adjusts the fader level for the selected channel.

8 Channel output level meter

Displays the channel's output signal level.

MATRIX1– MATRIX4 (V2.5 and later)

1 Channel name

Touch to display the CH NAME screen.

Touch to display information for a different channel.

2 Recall Safe button

Turns recall safe on and off for the corresponding channel.

You can display the RECALL SAFE screen (page 38) by touching the jump button in

the right corner of the Recall Safe button.

ձղ մնյ

շո

ձղ մյճ

նշ

Configuration screens

Reference Manual

TF series

3 Boxes

Touch to display the configuration screen for the corresponding feature.

You can touch the EQ, and COMP buttons displayed here to turn the corresponding

feature on and off.

FROM box: Displays the SEND FROM screen. (page 88)

EQ box: Displays the EQ screen. (page 59)

DELAY box: Displays the DELAY screen. (page 92)

4 Channel on/off button

Turns the selected channel on and off.

5 OUTPUT box

Displays the OUTPUT screen. (page 87)

6 Channel output level slider

Adjusts the fader level for the selected channel.

7 Channel output level meter

Displays the channel's output signal level.

CH VIEW screen menu

Press the Menu key ( ) from the CH VIEW screen to display the following options.

1 CH Copy

Copies the settings of the current channel.

2 CH Paste

Pastes settings from another channel and applies

them to the current channel.

3 CH Default

Resets the settings of the current channel to their

default values.

AUX/MATRIX channels (V4.0 and later)

4 CH Copy with Sends

Copies and also sends current channel settings.

5 CH Paste with Sends

Pastes settings copied from the selected channel,

including sending. When CH Copy with Sends is

executed, the CH Paste icon changes to CH Paste

with Sends.

Configuration screens

Reference Manual

TF series

CH NAME screen

Allows you to set the channel name, icon, and channel color.

1 Name text box

Enter the channel name here.

Touch the text box to enter the name using the KEYBOARD screen. (page 10)

2 Icon button

Touch to display a list of available channel icons.

3 Category button

Allows you to select a different category of channel icons.

The available categories vary depending on the type of channel.

4 Channel icon list

Touch to apply the channel icon.

You can drag this area up and down to display all of the available icons.

5 Sample Name button

Displays a list of commonly used channel names based on the selected channel icon.

Touch on a sample name to use it as the channel name.

6 Color button

Touch to display a list of available channel colors.

Touch the desired color to use that color as the channel color.

Configuration screens

Reference Manual

TF series

GEQ screen

You can use the internal graphic equalizer (GEQ) to process AUX 1–8 and STEREO channel signals.

The GEQ is a mono, 12-band EQ. Each band is 1/3 octave wide, with an adjustable gain range

of ±15 dB.

31 bands are available; you can adjust gain for up to 12 bands.

1 GEQ button

Turns the GEQ on and off.

2 GEQ channel selection buttons

These buttons are displayed only when configuring the GEQ for stereo AUX buses or the

STEREO channels.

They are not displayed for mono AUX buses.

: Turns the GEQ left/right channel link on and off.

L/R: Allows you select the left and right GEQ channels.

3 Recall Safe button

Displays the RECALL SAFE screen. (page 38)

4 Fader Assign button (V2.0 and later)

This feature is available for TF5/TF3/TF1.

When this button is turned on, you can use the faders to adjust each band of the GEQ.

5 EQ graph, RTA display, band selection

Displays the EQ settings with RTA (real-time analysis).

Swipe left or right or touch an area to display the gain sliders for other bands.

When the Fader Assign button is turned on, you can use this area to change which

bands can be adjusted by the faders. (TF3 and TF1 only.)

6 Gain slider

Adjusts the gain for the corresponding band.

Swipe left or right to display the gain sliders for other bands.

When the Fader Assign button is turned on, you can use this area to change which

bands can be adjusted by the faders. (TF3 and TF1 only.)

7 Output level meter

Displays the GEQ output level.

8 Available bands display

Displays the number of additional bands that you can adjust.

ձղ ճ մ

NOTE

Adjusts the sensitivity of RTA for RTA Offset on the PREFERENCE screen (



page 26). Allocate the RTA

Offset to the USER DEFINED KNOBS to adjust while the GEQ screen is displayed (available from V3.6).

Configuration screens

Reference Manual

TF series

GEQ screen menu

Press the Menu key ( ) from the GEQ screen to display the following options.

Using GEQ

1. Touch the GEQ button to turn GEQ on.

2. Swipe left or right on the gain sliders to display the

desired bands.

3. Drag sliders up and down to adjust the gain of the corresponding bands.

You can confirm the overall output using the output level meter.

Once you have adjusted gain for 12 bands, the gain sliders for the remaining bands are displayed in

gray. If you want adjust gain for other bands, you must first set the gain to 0 for one of the bands you

have already adjusted.

Touch the gain slider quickly two times to reset it to its default value (0 dB).

Selected gain settings can also be specified using the [TOUCH AND TURN] knob.

The [TOUCH AND TURN] knob functionality can be switched ON/OFF by pressing the [Shift] key.

Each press of the [Shift] key switches between setting gain and selecting the band. The same action

can be achieved by pressing the [TOUCH AND TURN] knob.

Holding down the [Shift] key resets the gain value for the selected band to zero decibels (default

value) (V4.0 and later).

Gain slider Output level meter

Using faders to adjust GEQ (TF5/TF3/TF1)

1. Touch the Fader Assign button to turn it on.

The current gain setting for each band is applied to the faders

in the channel strip section of the console.

You can confirm the frequency and gain for each band in the channel display.

2. For TF3 and TF1, swipe left or right on the gain sliders in the GEQ screen to select

other bands.

You can swipe the EQ graph, RTA display, or band selection area left or right to select other bands.

For TF5, all bands are applied to the faders.

3. Use the console's faders to adjust the gain.

If you turn on a channel's [ON] key, you can reset the gain of frequencies assigned to that channel to

0 dB.

4. When you are finished making adjustments, touch the Fader Assign button to turn

it off.

Fader Assign also turns off when you switch another screen or enter SENDS ON FADER mode.

1 Copy

Copies the GEQ parameters of the selected

channel to the clipboard.

2 Paste

Pastes the GEQ parameters in the clipboard to the

selected channel.

3 Compare

Allows you to compare the GEQ parameters of the

selected channel with the GEQ parameters in the

clipboard by switching between the two.

4 Default

Resets the GEQ settings for the current channel to

their default values.

Configuration screens

Reference Manual

TF series

OUTPUT screen

Allows you to configure how output channels will be output. The buttons displayed vary

depending on the type of output channel selected.

○

: Displayed

– : Not displayed

1 ST button

Determines whether the stereo channel is output or not.

2 SUB button (V3.0 and later)

Determines whether the channel's signal is sent (on) or not sent (off) to the SUB bus.

3 SUB slider (V3.0 and later)

Determines the amount of signal sent from the selected channel to the SUB bus.

4 Out Gain text box

Allows you to adjust the output gain.

When selected, you can use the [TOUCH AND TURN] knob to adjust the setting. Touch

again to display the keyboard and enter a value.

5 Φ (phase) button

Allows you to reverse the phase.

When turned on, the output signal's phase is reversed.

6 OMNI OUT button

Displays the number of the OMNI OUT to which the channel is directed.

Up to two numbers can be displayed. For three or more numbers, "+" is displayed.

Displays the OMNI OUT screen. (page 34)

For information about channels and output ports, see "Quick Config Input and input

channel relationships" (page 106).

7 Recall Safe button (V1.1 and later)

Turns recall safe on and off for the corresponding channel.

You can display the RECALL SAFE screen by touching the jump button in the right corner

of the Recall Safe button.

Output channel

Buttons

ST button

SUB button

SUB slider

Out Gain

Buttons

Φ button

OMNI OUT

Indicator

OMNI OUT

Buttons

AUX 1–8 – –

○○ ○ ○

AUX9/10–AUX19/20

○○○○○○

SUB – –

○○ ○ ○

STEREO – –

○○ ○ ○

MATRIX1–4 – –

○○ ○ ○

շմ

նյ

Configuration screens

Reference Manual

TF series

SEND FROM screen

Allows you to send signals from the each channels.

1 ON button

Determines whether a signal is sent (on) or not sent (off) from the corresponding each

channel.

2 Send pan slider

Adjusts the pan of the input channel signal that is sent.

For AUX1–AUX8 and MATRIX1–MATRIX4, this is displayed only if the signal type is set

to STEREO.

Not displayed for FX1L–FX2R.

3 Send level slider

Determines the amount of signal sent from the corresponding each channel.

4 Pre button

Allows you to select whether the signal sent from the input channel is from before or

after the fader.

On: Before the fader

Off: After the fader

Not displayed for MATRIX 1–4.

Adjusting the SEND FROM level

1. Touch the ON button for the input channels

that you want to send.

2. Touch the send pan slider, and then use the

[TOUCH AND TURN] knob to adjust the pan

of the input channel signal that is sent.

3. Drag the send level sliders to adjust the

amount of input channel signal that is sent.

Send level slider

Send pan slider

ON button

Pre button

Configuration screens

Reference Manual

TF series

SEND FROM screen menu

Press the Menu key ( ) from the SEND FROM screen to display the following options.

Adjusting the send level from AUX channels, STEREO channels, and SUB

channel to a MATRIX channel (V2.5 and later)

1. Touch the ON button for the AUX channel, STEREO channel, or SUB channel that

you want to send. (It is turned on by default.)

2. Drag the send level sliders to adjust the amount of AUX channel, STEREO channel,

and SUB channel signal that is sent.

3. When a MATRIX channel is set to "Stereo", the PAN slider can be used to pan the

sound. (V3.5 and later)

ON button

Send level slider

PAN slider

NOTE

• You can send the post-on signal of an AUX channel, STEREO channel, or SUB channel to a MATRIX

channel.

• Left and right channel SEND levels can be adjusted independently for stereo channels such as AUX 9/

10 and STEREO.

• When a MATRIX channel is set to "Stereo", the PAN slider becomes a BAL (balance) slider for the

stereo channel (V3.5 and later).

• To switch between "Stereo" and "MONOx2" for a MATRIX channel, use the settings on the BUS SETUP

screen, located in the SETUP screen. (page 33)

1 All Pre

Turns on all Pre buttons.

2 All Post

Turns off all Pre buttons.

3 All Nominal (V2.0 and later)

Sets all SEND levels to nominal (0 dB).

4 Dup. STEREO (V2.0 and later)

Duplicate STEREO. Copies each channel's fader

level and applies it to the SEND level.

5 Copy (V4.0 and later)

Copies the SEND level for the selected AUX/

MATRIX channel.

6 Paste (V4.0 and later)

Pastes the SEND level you copied to the selected

AUX/MATRIX channel.

Configuration screens

Reference Manual

TF series

DCA ASSIGN screen

Allows you to group channels together by assigning them to DCA groups.

1 Channel display area

Displays the channels that are assigned to the current DCA group.

2 DCA ASSIGN buttons

Allow you to select which channels are assigned to the current DCA group.

Selected channels are highlighted.

3 CH VIEW button

Displays the CH VIEW screen. (page 76)

4 Recall Safe button (V1.1 and later)

Turns recall safe on and off for the corresponding channel.

You can display the RECALL SAFE screen by touching the jump button in the right corner

of the Recall Safe button.

DCA ASSIGN screen menu

Press the Menu key ( ) from the DCA ASSIGN screen to display the following options.

ձ մղ

Assigning channels to a DCA group

1. Press the [INPUT1] and [INPUT2] buttons on the top panel simultaneously to display

the GROUP channels.

2. Press a [SEL] button on the top panel that corresponds to the DCA group that you

want to configure.

3. Touch the DCA buttons that correspond to the channels you want to assign to the

group. (You can select multiple channels.)

The selected channels are displayed in the channel display area.

1 Clear All

Removes all channels from the group.

Channel is selected

Configuration screens

Reference Manual

TF series

DCA roll out

You can assign DCA groups 1–8 to the last 8 channel strips on the right side of the console's

top panel.

(TF5: channel strips 25–32; TF3: 17–24; TF1: 9–16)

You can then assign the channels of a DCA group to the channel strips on the left side of the

console's top panel by pressing the corresponding DCA group's [SEL] key.

(TF5: channel strips 1–24; TF3: 1–16; TF1: 1–8)

The number of channels in the group that will be assigned to the channels strips depends on

the model number. For the TF5 console, the 24 lowest numbered channels in the group are

assigned; the lowest 16 for the TF 3, and the lowest 8 for the TF1.

This feature allows you to manipulate the channels strips for both the DCA group master and

the group's "member" channels at the same time.

NOTE

For TF-RACK, this item is displayed only in the OVERVIEW screen. The channels assigned to the faders

are the same as for the TF1.

Member channels of selected DCA group

assigned to these channel strips

DCA groups 1–8

assigned to these

channel strips

Configuration screens

Reference Manual

TF series

DELAY screen (V2.5 and later)

Sets the delay for signals output from MATRIX channels and the delay for signals input to the

ST IN channel (V4.0 and later).

1 DELAY button

Turns the DELAY on and off.

2 Display selection button (V3.5 and later)

When a MATRIX channel is set to "Stereo", select the MATRIX channel that will display

the parameters.

Two buttons are always displayed for the ST IN channel (V4.0 and later).

3 LR Link button (V3.5 and later)

If the MATRIX channel is set to stereo, the DELAY on/off and delay time operations for

the left/right channels will be linked together when this is turned on. When the delay

times are set to a different value, the delay times will operate in linked mode,

maintaining the time difference.

The LR Link button is always displayed for the ST IN channel (V4.0 and later).

4 DELAY slider

Allows you to adjust the delay time.

Delay time is displayed in frames, meters, feet, or ms (milliseconds).

5 DELAY setting

Determines the delay time by specifying frames, distance (meters or feet) or time

(milliseconds). Touch a text box to display the keyboard and enter a value.

NOTE

For MATRIX channels, this button is displayed only when the channel is set to stereo. Switch between

Stereo and MONOx2 using the BUS SETUP screen, located in the SETUP screen. (page 33)

Maintenance screen

Reference Manual

TF series

Maintenance screen

Allows you to access maintenance features.

1 Displays the Initialize All Memory screen.

2 Displays the Initialize Current Memory screen. (page 94)

3 Displays the Initialize NY64-D screen. (page 94) (V3.0 and later)

4 Displays the Input Port Trim screen. (page 95)

5 Displays the Output Port Trim screen. (page 95)

6 Displays the Fader Calibration screen. (page 96) (TF5/TF3/TF1)

7 Displays the Channel Color Calibration screen. (page 97) (TF5/TF3/TF1)

8 Closes the maintenance screen.

Initialize All Memory screen

Resets the console's memory, including Scene memory and Libraries, to the factory default

settings.

1 INITIALIZE button

Initializes the internal memory.

The following data is initialized: all Scene data, all Preset data, mixing data, and setup

data.

Touch to display the confirmation message. Touch the OK button to perform the

operation.

Do not touch any buttons until the initialization is complete.

When initialization is complete, you can continue to use other maintenance features

without exiting.

Using the maintenance screen

1. Turn on the console while pressing the Home key ( ).

The maintenance screen is displayed.

Touch the button that corresponds to the desired maintenance feature.

Touch the Exit button to exit the maintenance mode.

NOTE

• When initializing the internal memory, all data stored in the memory will be lost. Use caution when

performing this operation.

• The internal clock and network settings are not initialized by this operation.

• If an NY64-D is installed, we recommend you turn the TF series console off and on again so the

console will be set up correctly with the connected Dante devices.

Maintenance screen

Reference Manual

TF series

Initialize Current Memory screen

Resets the console's current memory to the factory default settings. Scene memory and

Libraries are not reset.

1 INITIALIZE button

Initializes the current memory.

The following data is initialized: mixing data and setup data.

Touch to display the confirmation message. Touch the OK button to perform the

operation.

Do not touch any buttons until the initialization is complete.

When initialization is complete, you can continue to use other maintenance features

without exiting.

Initialize NY64-D screen (V3.0 and later)

1 INITIALIZE button

Resets the settings of the NY64-D installed in the expansion slot. After initializing, in

order to reconfigure the connected Dante device, we recommend first turning the TF

series console off and then on again.

NOTE

When initializing the current memory, all data in the current memory will be lost. Use caution when

performing this operation.

NOTE

• A NY64-D card will be initialized even if Dante Device Lock has been enabled for it. In this case, Dante

Device Lock will be disabled after the card is initialized.

• The domain enrollment for the Dante Domain Manager will be canceled (available from V3.6).

• A label will be written to the Dante Channel Label for Receive/Transmit on the NY64-D corresponding

to the TF's I/O channels (available from V3.6).

Maintenance screen

Reference Manual

TF series

Input Port Trim screen

Allows you to adjust the gain of each INPUT jack in 0.01 dB increments.

1 INPUT jack selection buttons

Select the INPUT jack that you want to configure here.

Select the button that corresponds to the INPUT jack you want to configure, and then

use the [TOUCH AND TURN] knob to adjust the value.

After making adjustments, start up the console as usual.

2 Reset All button

Resets all values to 0.00 dB. The factory default setting is also 0.00 dB.

Touch to display the confirmation message. Touch the OK button to perform the

operation.

Output Port Trim screen

Allows you to adjust the gain of each OMNI OUT jack in 0.01 dB increments.

1 OMNI OUT jack selection buttons

Select the OMNI OUT jack that you want to configure here.

Select the button that corresponds to the OMNI OUT jack you want to configure, and

then use the [TOUCH AND TURN] knob to adjust the value.

After making adjustments, start up the console as usual.

2 Reset All button

Resets all values to 0.00 dB. The factory default setting is also 0.00 dB.

Touch to display the confirmation message. Touch the OK button to perform the

operation.

NOTE

When the reset is complete, you can continue to use other maintenance features without exiting.

NOTE

When the reset is complete, you can continue to use other maintenance features without exiting.

Maintenance screen

Reference Manual

TF series

Fader Calibration screen (TF5/TF3/TF1)

In some usage environments, discrepancies may occur in the motion of the motor faders. You

can use this screen to correct these discrepancies

1 START button

Starts the calibration.

Touch to display the confirmation message. Touch the OK button to perform the

operation.

2 Cancel button

Stops the calibration.

3 Apply button

Applies the settings and exits.

ձղճ

Calibrating the faders

1. Press the [SEL] key on the top panel that corresponds to the fader you want to

calibrate.

2. Touch the START button on the FADER CALIBRATION MODE screen.

3. Touch the OK button when the confirmation message is displayed.

4. When calibration has finished, touch the APPLY button.

5. Touch the Exit button in the maintenance menu and start up the console as usual.

If a fader must be calibrated again

If a fader must be calibrated again, the [ON] or [CUE] key of the corresponding fader will flash.

Use the following procedure to recalibrate.

1. When the message "Found faders requiring adjustment. Please calibrate faders again."

is displayed, touch the Close button to close the popup.

2. Touch the Apply button displayed on the screen.

[SEL] key of a fader that must be calibrated lights.

3. Slide the corresponding fader to the highest and lowest positions several times.

Make sure the fader's slide action is smooth and not getting stuck.

4. Perform the procedure described in "Calibrating the faders" beginning at step 2.

If you perform this procedure multiple times and the popup message is still displayed, contact

your Yamaha dealer.

NOTE

• This feature automatically calibrates the specified fader (channel strip or master section fader).

• When calibration is complete, you can continue to use other maintenance features without exiting.

Maintenance screen

Reference Manual

TF series

Channel Color Calibration screen (TF5/TF3/TF1)

You can adjust the colors of the LEDs as desired. LED colors are adjusted one at a time.

1 Color buttons

Allow you to select a color.

2 RGB knobs

Allow you to adjust the color.

3 Apply button

Applies the settings and exits.

4 Reset All button

Starts the calibration.

Touch to display the confirmation message. Touch the OK button to perform the

operation.

ղճմ

Adjusting channel colors

1. Press the [SEL] key on the top panel that corresponds to the channel color you want

to adjust.

2. Touch a color button to choose a color.

3. While comparing the [SEL] you selected with the other indicators on the top panel,

use the [TOUCH AND TURN] knob or the [USER DEFINED KNOBS] B, C, and D to

adjust the color.

4. When finished, touch the Apply button to apply the settings.

5. Touch the Exit button in the maintenance menu and start up the console as usual.

NOTE

• For TF3 and TF1, channels not supported by the console are not displayed.

• Only one channel color can be adjusted at a time.

• The Apply button is only displayed after you begin adjusting the channel's color.

• To reset all channel color's to their factory default values, touch the Reset All button.

• When the reset is complete, you can continue to use other maintenance features without exiting.

Reference

Reference Manual

TF series

Reference

List of parameters saved in Scenes and Presets

CH 1–40

*1 CH 1–32 only

*2 Only parameters are linked. (Gain reduction control is not linked.)

*3 Libraries created for CH 1–32 cannot recall to CH 33–40. Similarly, libraries created for CH 33–40 cannot recall to CH 1–32.

*4 CH1–8 only (V3.5 and later). AUTOMIXER parameters will not be updated when recalling libraries in CH1–8 that were created for CH9 and up.

*5 Automixer Group Bypass settings are not included in library or scene settings (V4.0 and later).

*6 Mute Group Master On/Off settings are not included in library or scene settings (V4.0 and later).

Channel Library Recall

Scene

Can use Scene Recall Safe

Stereo

Link

Recall CH

Recall EQ

Recall

Gate

Recall

Comp

All HA

Input

Select

Processing

Send To Fader On Name

(All)

(Exclude)

Input

Select

Name

Gain O

OO OOO O

+48V O

OO OOO

Digital Gain O OO OOO O

Input Select O O

O OO O O

Channel Name O O O

OO O

Category, Color, Icon O O O OO OO

Stereo Link

OO O

Direct Out

ON OOOO OO O

Point OOOO

OO O

HPF OOOOO

OO O O

PEQ OOOOO

OO O O

GATE

OOOO O OO O

COMP

OOOO OOO O

Automixer

OOOO OO O

Automixer Group Bypass

TO AUX

Level

OO O O

Pan

ON OO O O

Pre

OO O O

TO FX

Level

OO O O

Pre

OO O O

TO ST

Assign OOOO

OO O

Pan OOOO

TO SUB

Level OOOO

OO O O

ON OOOO

OO O O

Fader

OO O O

DCA Assign

OO O

Mute Assign

OO O

Mute Safe

Recall Safe

CUE

Reference

Reference Manual

TF series

ST IN 1, ST IN 2

*1 Input Select can only recall Libraries for the same channel.

*2 Mute Group Master On/Off settings are not included in library or scene settings (V4.0 and later).

*3 The Stereo link can also be disabled (V4.0 and later).

Channel Library Recall

Scene

Can use Scene Recall Safe

Stereo

Link

Recall CH

Recall EQ All HA

Input

Select

Processing

Send To Fader On Name

(All)

(Exclude)

Input

Select

Name

OO OOO

Digital Gain O OO OOO O

Input Select

OO O O

Channel Name O O O

OO OO

Category, Color, Icon O O O

OO OO

PEQ OOOOOOO

O O

Delay OOOO

OO O

TO AUX

Level

OO O O

Pan OO

ON OO O O

Pre

OO O O

TO FX

Level OO O O

OO O O

Pre

OO O O

TO ST

Assign OOOO OO O

Balance OOOO

OO O

TO SUB

Level OOOO

OO O O

ON OOOO OO O O

OO O O

Fader

OO O O

DCA Assign OO O

Mute Assign

OO O

Mute Safe

Recall Safe

CUE

Reference

Reference Manual

TF series

100

FX 1, FX 2

*1 For With Send, TO FX signals from CH 1–40, ST IN 1, and ST IN 2 can be recall safe.

*2 Mute Group Master On/Off settings are not included in library or scene settings (V4.0 and later).

Channel Library Recall

Scene

Can use Scene Recall Safe

Stereo

Link

Recall CH

Recall FX Recall EQ

With

Send

All FX

Processing

Send To Fader On Name

(All)

(Exclude)

FX Name

Channel Name O O

O O OO

Category, Color, Icon O O

O O OO

FX O

OO O OO O-

PEQ O O O

OO O O O

TO AUX

Level

O O O O

Pan

O O

ON O O O O

Pre

O O O O

TO ST

Assign O O O O O O

Balance O O O

O O O

TO SUB

Level O O O

O O O O

ON O O O O O O O

O O O O

Fader

O O O O

DCA Assign O O O

Mute Assign

O O O

Mute Safe

Recall Safe O

CUE

Reference

Reference Manual

TF series

101

AUX

*1 AUX 1–8 only

*2 AUX 9/10–19/20 only

*3 Only when L/R LINK for GEQ is turned on

*4 Libraries created for AUX 1–8 cannot recall to AUX 9/10–19/20. Similarly, libraries created for AUX 9/10–19/20 cannot recall to AUX 1–8.

*5 V3.5 and later

Channel Library Recall

Scene

Can use Scene Recall Safe

Stereo

Link

Recall CH

Recall

GEQ

Recall

COMP

Recall

With

Send

All

GEQ

Processing

Fader On Gain/Φ Name

(All)

(Exclude)

GEQ

Name

Channel Name O O O

O O O

Category, Color, Icon O O O O O OO

Signal Type

O O O

Pre Fader Send Point

O O O

Pan Link O O O O

O O O

PEQ OOOOO

O O O O

GEQ

O OO O O O O

COMP O O O O O O O O O

Ins FX

OO O OO OO O

TO ST Assign

OOOO O O O

TO SUB

Level O O O O O O O

ON OOOO

O O O

O O O O

Fader

O O O O

Send From

Level

OO O

Pan

OO O

Pre

OO O

OUTPUT

Balance O O O O

O O O

Out Gain OOOO

O O O

OOOO

O O O

Recall Safe O

CUE

Reference

Reference Manual

TF series

102

STEREO, SUB

*1 STEREO only

*2 SUB only

*3 Only when L/R LINK for GEQ is turned on

*4 Libraries created for STEREO cannot recall CH/EQ to SUB. Similarly, libraries created for SUB cannot recall CH/EQ to STEREO.

*5 Send From AUX9 to AUX20 settings were added (V3.0 and later).

Channel Library Recall

Scene

Can use Scene Recall Safe

Stereo

Link

Recall CH

Recall EQ

Recall

GEQ

Recall

COMP

With

Send

All

GEQ

Processing

Fader On Gain/Φ Name

(All)

(Exclude)

GEQ

Name

Channel Name O O

O O OO

Category, Color, Icon O O

O O OO

LPF

O O O O

PEQ OOOO O O O O

GEQ

O O O O OO

COMP O O O OO O O O

O O O O

Fader O O O O

STEREO/SUB Level Link

Send From

Level O

ON O

OUTPUT

Balance

OOO O O O

Out Gain O O O

O O O

Φ OOO O O O

Recall Safe O

CUE

Reference

Reference Manual

TF series

103

MATRIX (V2.5 and later)

*1 When L/R Link for DELAY is on

DCA

OMNI OUT

Channel Library Recall

Scene

Can use Scene Recall Safe

Stereo

Link

Recall CH

Recall EQ

With

Send

All FX GEQ

Processing

Fader On Gain/Φ Name

(All)

(Exclude)

Name

Channel Name O

O O O

Category, Color, Icon O O O OO

Signal Type

O O O

PEQ OOOO

O O O

DELAY O O

O O O

ON O O O O

Fader

O O O O

Send From

Level

OO O

Pan/Balance

OO O

OUTPUT

Balance O O

O O O

Out Gain O O

O O O

Φ OO O O O

Recall Safe O

CUE

Scene

Can use Scene Recall Safe

All Fader On Name

Channel Name O O

Category, Color, Icon O O O

ON O O

Fader O O O

DCA Assign O O

Recall Safe

CUE

Scene Can use Scene Recall Safe

OMNI OUT Patch O

O (All OMNI OUT)

Reference

Reference Manual

TF series

104

Access limitation parameter list

CH1-40

HA Input Select Processing Send To Fader/ON Name Other

CH1-40

High Level OOOOOOO

Mid Level OOOOOXO

Low Level XXXXOXX

ST IN

HA Input Select Processing Send To Fader/ON Name Other

ST IN 1-2

High Level OOOOOOO

Mid Level OXOOOXO

Low Level XXXXOXX

FX RTN

With Send FX Processing Send To Fader/ON Name Other

FX RTN 1-2

High Level OOOOOOO

Mid Level OOOOOX X

Low Level XXXXOXX

DCA

Fader/ON Name DCA Assign

DCA 1-8

High Level O O O

Mid Level O X X

Low Level O X X

OUTPUT

With Send FX GEQ Processing Fader/ON Gain/Φ Name Other

AUX1-8

High Level O

– OOOOOO

Mid Level O

– OOOX XO

Low Level X –XXOXXX

AUX9/10-19/20

High Level O O

– OOOOO

Mid Level O O

–OOXXO

Low Level X X –XOXXX

STEREO

High Level

– –OOOOOO

Mid Level

– –XXOXXX

Low Level – –XXOXXX

SUB

High Level O

– –OOOO –

Mid Level O

– –XOXX–

Low Level X – –XOXX–

MATRIX1-4

High Level O

– –OOOOO

Mid Level X

– –XXXXX

Low Level X – –XXXXX

Reference

Reference Manual

TF series

105

GENERAL

High Level Mid Level Low Level

Scene A

Store OOX

Recall OOO

Scene B

Store OOX

Recall OOO

Library A

Store OOX

Recall OOX

Library B

Store OOX

Recall OOX

Setup

+48V Master OXX

Bus Setup OOX

Brightness OOO

Custom Fader Bank OOX

File Load OXX

Network XXX

OMNI OUT Patch OXX

Preference OOO

Recall Safe OXX

Slot Setup OXX

Time XXX

User Defined Control OXX

Other

Automixer Group

Bypass

OOO

Monitor Delay OXX

Mute Group Name OXX

Mute Group Master OOO

Mute Safe OXX

Oscillator OOX

Stereo Link OOX

Reference

Reference Manual

TF series

106

Quick Config Input and input channel relationships

Tio1608-D: TF INPUT SLOT: TF INPUT CHANNEL TF OUTPUT CHANNEL: SLOT Tio1608-D: TF OUTPUT

Tio1608-D UNIT ID 1: INPUT1 SLOT IN 1 CH1 Input Select CH1 Direct Out SLOT OUT 1 No connection

Tio1608-D UNIT ID 1: INPUT2 SLOT IN 2 CH2 Input Select CH2 Direct Out SLOT OUT 2 No connection

Tio1608-D UNIT ID 1: INPUT3 SLOT IN 3 CH3 Input Select CH3 Direct Out SLOT OUT 3 No connection

Tio1608-D UNIT ID 1: INPUT4 SLOT IN 4 CH4 Input Select CH4 Direct Out SLOT OUT 4 No connection

Tio1608-D UNIT ID 1: INPUT5 SLOT IN 5 CH5 Input Select CH5 Direct Out SLOT OUT 5 No connection

Tio1608-D UNIT ID 1: INPUT6 SLOT IN 6 CH6 Input Select CH6 Direct Out SLOT OUT 6 No connection

Tio1608-D UNIT ID 1: INPUT7 SLOT IN 7 CH7 Input Select CH7 Direct Out SLOT OUT 7 No connection

Tio1608-D UNIT ID 1: INPUT8 SLOT IN 8 CH8 Input Select CH8 Direct Out SLOT OUT 8 No connection

Tio1608-D UNIT ID 1: INPUT9 SLOT IN 9 CH9 Input Select CH9 Direct Out SLOT OUT 9 No connection

Tio1608-D UNIT ID 1: INPUT10 SLOT IN 10 CH10 Input Select CH10 Direct Out SLOT OUT 10 No connection

Tio1608-D UNIT ID 1: INPUT11 SLOT IN 11 CH11 Input Select CH11 Direct Out SLOT OUT 11 No connection

Tio1608-D UNIT ID 1: INPUT12 SLOT IN 12 CH12 Input Select CH12 Direct Out SLOT OUT 12 No connection

Tio1608-D UNIT ID 1: INPUT13 SLOT IN 13 CH13 Input Select CH13 Direct Out SLOT OUT 13 No connection

Tio1608-D UNIT ID 1: INPUT14 SLOT IN 14 CH14 Input Select CH14 Direct Out SLOT OUT 14 No connection

Tio1608-D UNIT ID 1: INPUT15 SLOT IN 15 CH15 Input Select CH15 Direct Out SLOT OUT 15 No connection

Tio1608-D UNIT ID 1: INPUT16 SLOT IN 16 CH16 Input Select CH16 Direct Out SLOT OUT 16 No connection

Tio1608-D UNIT ID 2: INPUT1 SLOT IN 17 CH17 Input Select CH17 Direct Out SLOT OUT 17 No connection

Tio1608-D UNIT ID 2: INPUT2 SLOT IN 18 CH18 Input Select CH18 Direct Out SLOT OUT 18 No connection

Tio1608-D UNIT ID 2: INPUT3 SLOT IN 19 CH19 Input Select CH19 Direct Out SLOT OUT 19 No connection

Tio1608-D UNIT ID 2: INPUT4 SLOT IN 20 CH20 Input Select CH20 Direct Out SLOT OUT 20 No connection

Tio1608-D UNIT ID 2: INPUT5 SLOT IN 21 CH21 Input Select CH21 Direct Out SLOT OUT 21 No connection

Tio1608-D UNIT ID 2: INPUT6 SLOT IN 22 CH22 Input Select CH22 Direct Out SLOT OUT 22 No connection

Tio1608-D UNIT ID 2: INPUT7 SLOT IN 23 CH23 Input Select CH23 Direct Out SLOT OUT 23 No connection

Tio1608-D UNIT ID 2: INPUT8 SLOT IN 24 CH24 Input Select CH24 Direct Out SLOT OUT 24 No connection

Tio1608-D UNIT ID 2: INPUT9 SLOT IN 25 CH25 Input Select CH25 Direct Out SLOT OUT 25 No connection

Tio1608-D UNIT ID 2: INPUT10 SLOT IN 26 CH26 Input Select CH26 Direct Out SLOT OUT 26 No connection

Tio1608-D UNIT ID 2: INPUT11 SLOT IN 27 CH27 Input Select CH27 Direct Out SLOT OUT 27 No connection

Tio1608-D UNIT ID 2: INPUT12 SLOT IN 28 CH28 Input Select CH28 Direct Out SLOT OUT 28 No connection

Tio1608-D UNIT ID 2: INPUT13 SLOT IN 29 CH29 Input Select CH29 Direct Out SLOT OUT 29 No connection

Tio1608-D UNIT ID 2: INPUT14 SLOT IN 30 CH30 Input Select CH30 Direct Out SLOT OUT 30 No connection

Tio1608-D UNIT ID 2: INPUT15 SLOT IN 31 CH31 Input Select CH31 Direct Out SLOT OUT 31 No connection

Tio1608-D UNIT ID 2: INPUT16 SLOT IN 32 CH32 Input Select CH32 Direct Out SLOT OUT 32 No connection

Tio1608-D UNIT ID 3: INPUT1

SLOT IN 33

CH33 Input Select

AUX1 Output SLOT OUT 33 Tio1608-D UNIT ID 1: OUTPUT1

Tio1608-D UNIT ID 3: INPUT2

SLOT IN 34

CH34 Input Select

AUX2 Output SLOT OUT 34 Tio1608-D UNIT ID 1: OUTPUT2

Tio1608-D UNIT ID 3: INPUT3

SLOT IN 35

CH35 Input Select

AUX3 Output SLOT OUT 35 Tio1608-D UNIT ID 1: OUTPUT3

Tio1608-D UNIT ID 3: INPUT4

SLOT IN 36

CH36 Input Select

AUX4 Output SLOT OUT 36 Tio1608-D UNIT ID 1: OUTPUT4

Tio1608-D UNIT ID 3: INPUT5

SLOT IN 37

CH37 Input Select

AUX5 Output SLOT OUT 37 Tio1608-D UNIT ID 1: OUTPUT5

Tio1608-D UNIT ID 3: INPUT6

SLOT IN 38

CH38 Input Select

AUX6 Output SLOT OUT 38 Tio1608-D UNIT ID 1: OUTPUT6

Tio1608-D UNIT ID 3: INPUT7

SLOT IN 39

CH39 Input Select

AUX7 Output SLOT OUT 39 Tio1608-D UNIT ID 2: OUTPUT1

Tio1608-D UNIT ID 3: INPUT8

SLOT IN 40

CH40 Input Select

AUX8 Output SLOT OUT 40 Tio1608-D UNIT ID 2: OUTPUT2

*1 No connection for TF1, TF-RACK.

Reference

Reference Manual

TF series

107

* When quick config is turned off, this table also applies for mixer SLOT channels.

No connection SLOT IN 41 No connection AUX9 Output SLOT OUT 41 Tio1608-D UNIT ID 2: OUTPUT3

No connection SLOT IN 42 No connection AUX10 Output SLOT OUT 42 Tio1608-D UNIT ID 2: OUTPUT4

No connection SLOT IN 43 No connection AUX11 Output SLOT OUT 43 Tio1608-D UNIT ID 2: OUTPUT5

No connection SLOT IN 44 No connection AUX12 Output SLOT OUT 44 Tio1608-D UNIT ID 2: OUTPUT6

No connection SLOT IN 45 No connection AUX13 Output SLOT OUT 45 Tio1608-D UNIT ID 3: OUTPUT1

No connection SLOT IN 46 No connection AUX14 Output SLOT OUT 46 Tio1608-D UNIT ID 3: OUTPUT2

No connection SLOT IN 47 No connection AUX15 Output SLOT OUT 47 Tio1608-D UNIT ID 3: OUTPUT3

No connection SLOT IN 48 No connection AUX16 Output SLOT OUT 48 Tio1608-D UNIT ID 3: OUTPUT4

No connection SLOT IN 49 No connection AUX17 Output SLOT OUT 49 Tio1608-D UNIT ID 3: OUTPUT5

No connection SLOT IN 50 No connection AUX18 Output SLOT OUT 50 Tio1608-D UNIT ID 3: OUTPUT6

No connection SLOT IN 51 No connection AUX19 Output SLOT OUT 51 Tio1608-D UNIT ID 3: OUTPUT7

No connection SLOT IN 52 No connection AUX20 Output SLOT OUT 52 Tio1608-D UNIT ID 3: OUTPUT8

No connection SLOT IN 53 No connection MATRIX1 OUT (V2.5 and later) SLOT OUT 53 No connection

No connection SLOT IN 54 No connection MATRIX2 OUT (V2.5 and later) SLOT OUT 54 No connection

No connection SLOT IN 55 No connection MATRIX3 OUT (V2.5 and later) SLOT OUT 55 No connection

No connection SLOT IN 56 No connection MATRIX4 OUT (V2.5 and later) SLOT OUT 56 No connection

No connection SLOT IN 57 No connection

STEREO L Output SLOT OUT 57

Tio1608-D UNIT ID 1: OUTPUT7,

Tio1608-D UNIT ID 2: OUTPUT7

No connection SLOT IN 58 No connection

No connection SLOT IN 59 No connection

STEREO R Output SLOT OUT 58

Tio1608-D UNIT ID 1: OUTPUT8

Tio1608-D UNIT ID 2: OUTPUT8

No connection SLOT IN 60 No connection

No connection SLOT IN 61 No connection SUB Output SLOT OUT 59 No connection

No connection SLOT IN 62 No connection No connection SLOT OUT 60 No connection

No connection SLOT IN 63 ST IN 2L Input Select MONITOR L Output SLOT OUT 61 No connection

No connection SLOT IN 64 ST IN 2R Input Select MONITOR R Output SLOT OUT 62 No connection

No connection SLOT OUT 63 No connection

No connection SLOT OUT 64 No connection

Tio1608-D: TF INPUT SLOT: TF INPUT CHANNEL TF OUTPUT CHANNEL: SLOT Tio1608-D: TF OUTPUT

Reference

Reference Manual

TF series

108

Warnings and error messages

Message Description

Item Already Exists. Replace it? Displayed when you are about to store (overwrite) a Library.

File Already Exists, Replace it?

When using Save As, the name of the file you tried to save was the

same name as an existing file.

Displayed when you are about to save (overwrite) data.

Exceed Maximum Number!

Library A:XXXX items, Library B:XXXX

items

The Library exceeds the maximum number of items and cannot be

loaded.

File System is Not Ready. This

Operation can Overwrite Existing Files

or Directories.

You tried to start recording immediately after connecting a USB storage

device (i.e., while a list was being generated). You tried to change the

name of a file or directory.

Over Current Error! This USB Device is

Not Supported. Please Disconnect.

The USB device was disconnected because overcurrent was detected in

the USB connection.

Tio OUTPUT is in Use by Another TF.

"with OUTPUT" in Quick Config is

Turned off.

The OUTPUT of the Tio1608-D is already in use by a console using

Quick Config, therefore the "with OUTPUT" in Quick Config was turned

off for this console.

Operation Failed!

An error occurred during the operation. (This is a general error.)

Less severe than "Unknown".

(Between "Unknown" and "Ignore".)

Invalid Name! Name violates naming convention.

Operation Ignored.

The feature assigned to the knob was not operated. The operation had

no effect.

This message refers to Tips operations for User Defined Knobs.

This message is displayed when the feature assigned to a User Defined

Knob cannot be operated.

SCENE #XX is Empty!

No data is stored in the Scene you tried to recall, or the data is

damaged.

SCENE #XX is Read Only! You tried to overwrite a Scene that is write-protected.

Cannot Store! Could not save the data in the Scene memory or in the Library.

Cannot Recall! Could not recall the data from the Scene memory or from the Library.

Operation Failed. Library X Memory

Full.

You tried to add data when the memory was full.

A or B will be entered into X.

Wrong Word Clock! (Slot)

The sample rate setting of the NY64-D is incorrect, therefore it cannot

sync with the console.

Turn Off 1-knob Mode to Adjust. 1-knob mode is enabled; turn 1-knob mode off.

Nothing to Paste! You tried to paste data when the copy buffer was empty.

Cannot Bookmark This Screen. You tried to bookmark a screen that cannot be bookmarked.

Page Does not Exist. The page does not exist.

Cannot Close This Popup. The popup could not be closed.

Not Bookmarked. The item is not bookmarked.

File Busy! Operation Denied.

The operation could not be performed because the USB memory was

being accessed.

Unsupported File Format! You tried to read an unsupported file format from the USB memory.

Storage Not Found! The USB memory could not be recognized.

Couldn't Write File. The file could not be saved to the USB memory.

File Protected!

Could not overwrite the file on the USB memory because the file is

write-protected.

Already Exists!

The name of the directory you tried to create matches the name of an

existing directory.

This message may also be displayed when editing a file or directory

name.

Couldn't Access File. Could not access the file on the USB memory for some reason.

File Error! An internal file access error occurred.

Format Error! An error occurred during formatting.

Loading Title List. Loading audio file from USB Recorder (V4.0 and later).

USB Storage Unmounted! Recorder

Stopped.

Recording stopped because the USB memory was removed during

recording.

USB Storage Full! Recorder Stopped.

Recording stopped because the USB memory became full during

recording.

Recorder supports a maximum of 150

items in a folder. Please remove some

files from this folder to continue.

If the number of audio files to be loaded by the Recorder, including the

number of folders, exceeds 150 (V4.0 and later).

USB Storage Busy: Recorder Stopped!

Recording or playback stopped because time is required for a USB

storage device process.

Illegal Storage Format! Format USB

Device with the Other USB Port.

A USB memory device with an allocation unit size under 4096 bytes

was connected. If you record in this situation, the format may become

damaged.

Low Battery! The backup battery's voltage is low.

Illegal IP Address! The IP address setting or gateway setting is incorrect.

USB Sample Rate Mismatch on USB.

Console:44100Hz

The same rates of the console and the computer that is connected to

the USB TO HOST connector are different. (Console: 44.1 kHz, PC; 48

kHz)

Set the sample rate of the computer to 44.1 kHz.

USB Sample Rate Mismatch on USB.

Console:48000Hz

The same rates of the console and the computer that is connected to

the USB TO HOST connector are different. (Console: 48kHz, PC;

44.1kHz)

Set the sample rate of the computer to 48kHz.

Two or More Devices Have Same Unit

ID!

Two or more devices connected to the NY64-D via the Dante network

have the same UNIT ID.

Dante Module Error!

An error occurred with the Dante module of the NY64-D, Tio1608-D or

other device.

Illegal Dante Module MAC Address!

The MAC address of the NY64-D is damaged and communication is not

possible.

Dante Module Memory Error!

A memory error occurred with the Dante module of the Tio1608-D or

other device.

Message Description

Reference

Reference Manual

TF series

109

Dante Audio Resource Overflow

An excessive amount of audio data was sent over the Dante network

connected to the NY64-D.

Under Synchronization

Settings are bring performed for a Tio1608-D on the Dante network

connected to the NY64-D.

When the Tio1608-D is in Resume mode, this message may be

displayed continuously on the SLOT SETUP screen. This is not a

malfunction.

Wrong Word Clock! (Dante Device)

The sample rate setting of a device on the Dante network connected to

the NY64-D is incorrect, therefore the device cannot sync to the NY64-

Linked at 10/100Mbps. Check Cables

or Switches.

A switch or cable that does not support Gigabit Ethernet is connected

to the Dante network connected to the NY64-D.

Error on the Dante Primary Port

When using a redundancy network, an error has occurred on the

PRIMARY network and the SECONDARY network is being used.

Error on the Dante Secondary Port

When using a redundancy network, an error has occurred on the

SECONDARY network.

Dante Patch or Setting Modified

A setting that is different from the values determined by Quick Config

has been set, perhaps by Dante Controller.

Dante Setting Mismatch

The UNIT ID switch on the Tio1608-D panel does not match the actual

unit ID. This is displayed when you change the Tio1608-D's UNIT ID

while the Tio1608-D is locked using Dante Device Lock, or when you

change the switch after turning the unit on.

Restart Tio to Complete Quick Config

The Tio1608-D Device Config or other settings do not equal Quick

Config values. Restart the Tio1608-D.

No Option Card Installed

There is no NY64-D card installed in the expansion slot.

This message is displayed when the Quick Config button is ON and

there is no NY64-D card installed.

TF Controls First 24 Dante Devices

Found

The maximum number of I/O Racks (Tio1608-D, R series, DZR-D series,

DXS-XLF-D series, etc.) on the Dante network connected to the NY64-

D has been exceeded.

TF Controls HAs of Maximum of

8 Dante Devices

The maximum number of Dante devices with HA on the Dante network

connected to the NY64-D has been exceeded.

Unknown Option Card Installed! An unsupported card has been found in the console's expansion slot.

Overcurrent Detected (Slot) Overcurrent was detected in the card installed in the expansion slot.

Slot Communication Error!

A communication error occurred in the card installed in the expansion

slot.

Dante Module Restarted! The Dante module of the NY64-D was restarted.

Dante Setting Error! Please Restart the

Console.

An error occurred in the Dante module of the NY64-D that requires you

to restart the console.

If this message is displayed, restart the console.

Dante I/O Device Disconnected A Dante device was disconnected from the NY64-D.

Two or More HA Controllers may

Cause Conflict

More than one device on the Dante network can control the same

device's HA, therefore operational conflicts may occur.

This message is displayed every time the HA Control on the SLOT

SETUP screen is turned on, but it does not indicate a malfunction.

Message Description

Dante devices are locked. Use Dante

Controller to unlock devices.

This is displayed when you touch the Quick Config button while the

Tio1608-D or NY64-D are locked using Dante Device Lock. In this case,

patching is not performed automatically by Quick Config, but it does

not indicate a malfunction. Dante Controller (v3.10.0.19 and later) is

required to unlock the devices.

Permission Denied!

The user does not have permission to perform the operation, therefore

the operation was ignored.

Operation ignored, you are not

logged-in.

The user is not logged in, therefore the operation cannot be performed.

Incorrect password entered. The password that was entered is incorrect.

This console is enrolled in a Dante

Domain. Quick Config is disabled.

Quick Config will be turned off, as the console was enrolled to the

Dante domain by the Dante Domain Manager.

Message Description

Index

Reference Manual

TF series

110

Index

Numerics

1-knob COMP.................................. 65

1-knob EQ ....................................... 60

Intensity ....................................... 60

Loudness ..................................... 60

Vocal............................................ 60

ACCESS PERMISSION screen ...... 45

ASSIGN screen ............................... 74

Audio file.......................................... 15

Auto CH Select................................ 25

AUTOMIXER screen ....................... 74

AUX1–AUX8 channels .................... 48

AUX9/10–19/20 channels................ 48

AUX9/10–AUX19/20.......................... 7

CH STRIP section ........................... 47

CH VIEW screen ............................. 76

Channel Color Calibration screen ... 97

COMP screen.................................. 65

Configuration screens ................. 5, 57

CUE................................................. 19

CUSTOM FADER BANK screen

menu .............................................. 32

Daylight saving time

(summer time) ................................ 42

DCA ASSIGN screen ...................... 90

DCA group....................................... 90

DELAY screen................................. 92

Digital gain....................................... 58

Direct out ......................................... 77

Displaying configuration screens..... 11

EQ screen ....................................... 59

EQ screen menu ............................. 63

Fader Calibration screen................. 96

FADER section ............................... 49

File information ............................... 18

Footswitch....................................... 29

FX screen (FX1/2, InsFX1–6) ......... 67

GainFinder ...................................... 57

GATE screen .................................. 63

Gateway.......................................... 41

GEQ screen .................................... 85

Group channels............................... 49

Initialize (internal memory).............. 93

Initialize (NY64-D)........................... 94

Initialize All Memory screen ............ 93

Initialize Current Memory screen .... 94

Input channels................................. 47

Input Port Trim screen .................... 95

INPUT screen ................................. 57

Internal clock................................... 42

IP address....................................... 41

Keyboard screen............................. 10

Level meter ..................................... 14

Library ............................................... 8

Library screen ................................... 8

License information......................... 43

Maintenance screen........................ 93

MATRIX1–MATRIX4 channels ....... 48

Menu ............................................... 10

METER screen................................ 14

Metering point ................................. 14

Monitor ............................................ 19

MONITOR screen ........................... 19

MP3................................................. 15

OMNI OUT....................................... 34

OMNI OUT screen menu................. 34

Oscillator.......................................... 21

Output Port Trim screen .................. 95

OUTPUT screen .............................. 87

OVERVIEW screen ......................... 47

OVERVIEW screen operations........ 54

Peak Hold ........................................ 14

Phantom power ............................... 58

Phase .............................................. 58

PHONES jack .................................. 20

Playback .......................................... 15

Playback mode ................................ 18

Preset ................................................ 8

Recall on/off checkboxes................... 8

RECORDER screen (INPUT/

OUTPUT/TITLE LIST screen) ........ 15

RECORDER screen menu .............. 19

Recording ........................................ 15

RTA display ..................................... 85

SAVE/LOAD screen menu .............. 23

Scene .............................................. 11

SCENE screen ................................ 11

SCENE screen menu ...................... 13

SEND FROM screen ....................... 88

Send pan ......................................... 88

SEND TO AUX screen .................... 73

SETUP screen................................. 22

Stereo channels............................... 47

Stereo link........................................ 57

SUB channels.................................. 48

Subnet mask.................................... 41

Time stamp...................................... 42

Toolbar ............................................ 11

USER ACCOUNT screen................ 44

USER DEFINED KEYS................... 27

USER DEFINED KNOBS................ 27

Version information ......................... 43

Warnings and error messages ...... 108

WAV ................................................ 15

Index

Reference Manual

TF series

111

I Operations and

settings

Access

Applying access permissions ...... 46

Button and slider operations............ 10

Checking the input signals .............. 20

Copying and pasting channel

settings........................................... 55

CUSTOM FADER BANK

Recalling...................................... 32

Custom fader bank

Configuring .................................. 32

DCA groups

Assigning channels...................... 90

Editing a Preset ................................. 9

Editing a Scene ............................... 12

1-knob EQ mode ......................... 61

GEQ............................................. 86

HPF ............................................. 62

LPF .............................................. 62

Manual mode............................... 61

Feature assignments

Assigning to footswitch ................ 31

Assigning to [USER DEFINED

KEYS] .......................................... 30

Assigning to [USER DEFINED

KNOBS] ....................................... 31

Playback

Files on USB storage device ....... 19

Recall safe

Using recall safe.......................... 38

Recalling a Preset............................. 9

Recalling a Scene ........................... 12

Recording

Recording.................................... 18

Setting

Adjust the send level ................... 89

AUTOMIXER............................... 75

Channel colors ............................ 97

Compressor................................. 66

Effects ......................................... 68

Fader calibration ......................... 96

Gate ............................................ 64

Input ............................................ 16

Insert effects................................ 68

Oscillator ..................................... 21

Output ......................................... 17

PREFERENCE screen................ 26

SEND FROM level ...................... 88

SEND TO AUX level ................... 73

Stereo link, input source.............. 58

Product dimensions

Reference Manual

TF series

112

Product dimensions

224

599

480

225

599

510

716

225

599

866

225

599

TF5 TF3

TF1 TF1 rack mount (14U)

Unit: mm

Product dimensions

Reference Manual

TF series

113

TF-RACK

Unit: mm

ME TER

Pr e DG

GAIN/TRIM

DIGITAL

GAIN

ME TER

Pr e HPF

HPF

4BAND

ME TER

EQ OUT

GATE COMP

GR METER GR METER

ME TER

GATE OUT

ME TER

COMP OUT

Pr e HPF Pr e FADER

ME TER

Post ON

PA N

INPUT

SE LE CT

FX1

SE ND

TO FX1/FX2

Pr e EQ / Pr e Fader / Post ON

AUX1

TO AUX1-8

AUX1

SE ND

TO AU X1-8

AUX:Stereo

PA N

SUB

SUB LEV EL

Pre FADER

CUE

Pr e DG

Pr e HPF

Pre FADER

Post ON

D I RE CT OU T

FX1

SLOT IN 1-3 2

Post EQ

CH1-32

Pr e DG

FX2

Pan Li nk

AUX9

SE ND

TO AUX9/10-19/20

PA N

ST IN 1,2

DIGITAL

GAIN

2BAND

ME TER

Pr e EQ

Pre FADER L

FADER( DCA)

ME TER

Pr e Fa de r

BA L

Pre FADER R

Pre FADER L+R

Post ON R

Post ON L

Post ON L+R

AUX:Mono

AUX1

SE ND

TO AU X1-8

AUX:Stereo

CUE

AUX1

PA N

SE NDON

AUX9

PA N

SE NDON

TO AU X9/10-19/20

FX1,2 RTN

2BAND

METER

Pr e EQ

Pre FADER L

FADER(DCA)

METER

EQ OUT

BA L

Pre FADER R

Pre FADER L+R

Post ON R

Post ON L

Post ON L+R

Same as ST IN 1,2

TO AU X1-8

Same as ST IN 1,2

TO AU X9/10-19/20

FADER(DCA)

SE ND

( DCA CUE

Post PA N L

Post PA N R

AUX10

AUX2

AUX10

AUX9

AUX10

AUX2

AUX1

AUX2

ME TER

Pr e DG

ME TER

Post ON

METER

Post ON

CUE

Pre FADER L

Pre FADER R

Post ON L

Post ON R

( DCA CUE

Same as ST IN 1,2

CUE

TO FX1/FX2

FX1

SE ND

ST L

ST R

SUB

FX1

FX2

AUX10

AUX9

AUX20

AUX19

AUX1

AUX2

AUX8

CUE L

CUE R

AUX:Mono

COMBO JACK

+48V

Post PA N L

Post PA N R

USB IN 1-3 2

SUB

SUB LEV EL

SUB

SUB LEV EL

MA TR IX 1

MA TR IX 2

MA TR IX 3

MA TR IX 4

METER

Pr e DG

DIGITAL

GAIN

ME TER

Pr e HPF

2BAND

METER

EQ OUT

Pr e HPF

FADER(DCA)

METER

Post ON

PA N

INPUT

SE LE CT

SUB

SUB LEV EL

PRE FA DERPr e DG

Same as CH1-32

TO FX1/FX2

Same as CH1-32

TO AUX1-8

Same as CH1-32

TO AUX9/10-19/20

Same as CH1-32

CUE

CH33-40 ( TF5, TF3 )

USB IN 1-8

INPUT 1-8 ( TF5 )

INPUT 9-16( TF3)

HPF

SLOT IN 33-40

INPUT 1-16, 17-24, 25-32( TF5 )

INPUT 1-16, 17-24, 1-8( TF3 )

INPUT 1-16, 1-8, 9-16( TF1 )

[INPUT1-32](TF5)

[INPUT1-24](TF3)

[INPUT1-16](TF1)

-10dBV

PL AY BA CK R

[ST IN 1]

-10dBV

[ST IN 2]

PL AY BA CK L

INPUT SEL ECT

ST IN 1L

ST IN 1R

USB IN 34

USB IN 33

INPUT SEL ECT

ST IN 2L

ST IN 2R

SLOT IN 64

SLOT IN 63

TF5,3,1 Mixer Block Diagram 1/2

Pr e EQ

Pr e EQ / Pr e Fader / Post ON

AUTOMIXER

Automix Gain

METER

CH1-8 Only

Pr e Fa de r / Po st ON

Pr e EQ / Pr e Fader / Post ON

Pr e EQ

Pr e EQ L Pr e EQ R

Pr e EQ L+R

Pr e EQ / Pr e Fader / Post ON L+R

Pr e EQ / Pr e Fader / Post ON L

Pr e EQ / Pr e Fader / Post ON R

Pr e EQ / Pr e Fader / Post ON L

Pr e EQ / Pr e Fader / Post ON R

Pr e EQ L Pr e EQ R

Pr e EQ L+R

Pr e Fa de r / Po st ON L+R

USB OUT 1-32,

SLOT OUT 1-32

METER

EQ OUT

Block diagram

[PHONES]

LEVEL

Pink Noise

Burst Noise

METER

OSC

OSCILLATOR

Sine Wave

ST L

ST R

SUB

AUX1

AUX2

AUX8

USB

HOST

I/F

REC L

REC R

PL AY BA CK L

PL AY BA CK R

[iPad]

[USB TO HOST]

PL AY BA CK L e ve l

AUX9

AUX10

AUX19

AUX20

OMNI OUT PATCH

CH1-32 Pre FADER

ST IN 1,2 Pre FAD E R

FX1,2 RTN Pre FADER

AUX1-8 Pr e FAD ER

AUX9-20 Pr e FAD E R

ST, SUB P re FA DE R

INPUT

SE LE CTOR

RTA

CUE

METER

Sample Rate

Convertor

ST L

ST R

SUB

FX1

FX2

AUX10

AUX9

AUX20

AUX19

AUX1

AUX2

AUX8

CUE L

CUE R

STEREO

4BAND

ME TER

Pr e EQ

FADER

ME TER

EQ OUT

ME TER

COMP OUT

BA L

CUE

COMP

GR METER

FlexGEQ

ME TER

Post ON

ME TER

GEQ O UT

GAIN

SUB

LPF

2BAND

METER

PRE LPF

FADER

ME TER

COMP OUT

COMP

GR METER

ME TER

Post ON

METER

EQ OUT

GAIN

Pr e Fader R

STE REO OUT R

STE REO OUT L

SUB OUT

AUX2 OUT

AUX1 OUT

AUX8 OUT

AUX10 OUT

AUX9 OUT

AUX19 OUT

AUX20 OUT

MO NITOR OUT L

MO NITOR OUT R

SLOT

DIRE CT OUT 1-32 ( as SLOT OUT 1-32 )

AUX OUT 1-20 ( a s SLOT OUT 33-52 )

STE REO OUT L/R, SUB OU T, MO NITOR OUT

( as SLOT OUT 57,58,59,61,62 )

SLOT IN 1-32 ( as CH 1-32 INPUTs )

SLOT IN 63, 64( as ST IN 2 INPUTs )

MATRIX OUT 1-4 ( as SLOT OUT 53-56 )

MATRIX1

MATRIX2

MATRIX3

MATRIX4

MA TRIX1 OUT

MA TRIX2 OUT

MA TRIX3 OUT

MA TRIX4 OUT

TO MATRI X1-4

SE ND

MA TR IX 1-4

SLOT IN 33-40 ( as CH 33-40 INPUTs: TF5, TF3 )

CH33-40 Pr e FADER( TF5, TF3 )

TF5,3,1 Mixer Block Diagram 2/2

Pr e Fa de r L

Post ON R

Post ON L

Post ON R

Post ON L

PA N

SE ND

Post ON R

Post ON L

BA L

Pr e Fa de r / Po st ON L

Pr e Fa de r / Po st ON R

CUE

MATRIX:Stereo

MATRIX:Mono

AUX1-8

4BAND

METER

Pr e EQ

FADER

METER

EQ OUT

ME TER

COMP OUT

COMP

GR METER

ME TER

Post ON

ME TER

GEQ O UT

GAINFlexGEQ

MATRI X1-4

FADER

ME TER

Post ON

DELAY

4BAND

METER

EQ OUT

GAIN

METER

Pr e EQ

PHONES LEVEL

MO NITOR LE VE L

MONITOR

SELECT

STE REO OU T

SUB OUT

ST IN 1

ST IN 2

PLAY BA CK

USB IN 33,34

CUE LOGIC

ME TER

DELAY

MO NO

MONITOR / CU E

REC

SE LE CT

REC L

REC R

CUE

REC LEVEL

ME TER

ST L /R Pre FAD ER

AUX 1/2 Pr e FAD E R

AUX 3/4 Pr e FAD E R

MTRX 1/2 Pre FADER

MTRX 3/4 Pre FADER

Pr e Fa de r

Post ON

CUE

TO MATRI X1-4

SE ND

Post ON

SE ND

Post ON

Pr e Fa de r / Po st ON

CUE

MATRIX:Stereo

MATRIX:Mono

Pr e Fa de r Post ON

TO MATRI X1-4

Same as SUB

CUE

Same as SUB

4BAND

METER

Pr e EQ

COMP

GR METER

FADER

METER

EQ OUT

BA L

AUX9/10-19/20

ME TER

PRE FA DER

ME TER

Post ON

GAIN

ME TER

INSERT

EFFE CT

COMP OUT

Pr e Fa de r R

Pr e Fa de r L

Post ON R

Post ON L

Post ON R

Post ON L

Post ON R

SUB SE ND

TO MATRI X1-4

Same as STEREO

CUE

Same as STEREO

CUE

Pr e Fa de r / Po st ON

CUE

ME TER

Pr e Fa de r

Pr e Fa de r Post ON

AUX 5/6 Pr e FAD E R

AUX 7/8 Pr e FAD E R

[OMNI OUT 1]

+4dBu

[OMNI OUT 2]

+4dBu

[OMNI OUT 3]

+4dBu

[OMNI OUT 16]

+4dBu

TRIM

USB I/F

D I RE CT OU T 1 - 3 2

REC L

REC R

USB IN 1-3 4

STEREO OUT L/R

MATRIX OUT 1-4

ME TER

Pr e DG

GAIN/TRIM

DIGITAL

GAIN

ME TER

Pr e HPF

HPF

4BAND

ME TER

EQ OUT

GATE COMP

GR METER GR METER

ME TER

GATE OUT

ME TER

COMP OUT

Pr e HPF Pr e FADER

ME TER

Post ON

PA N

INPUT

SE LE CT

FX1

SE ND

TO FX1/FX2

Pr e EQ / Pr e Fader / Post ON

AUX1

TO AUX1-8

AUX1

SE ND

TO AU X1-8

AUX:Stereo

PA N

SUB

SUB LEV EL

Pre FADER

CUE

Pr e DG

Pr e HPF

Pre FADER

Post ON

D I RE CT OU T

FX1

SLOT IN 1-3 2

Post EQ

CH1-32

Pr e DG

FX2

Pan Li nk

AUX9

SE ND

TO AUX9/10-19/20

PA N

ST IN 1,2

2BAND

ME TER

Pr e EQ

Pre FADER L

FADER( DCA)

ME TER

EQ OUT

BA L

Pre FADER R

Pre FADER L+R

Post ON R

Post ON L

Post ON L+R

AUX:Mono

AUX1

SE ND

TO AU X1-8

AUX:Stereo

CUE

AUX1

PA N

SE NDON

AUX9

PA N

SE NDON

TO AU X9/10-19/20

FX1,2 RTN

2BAND

METER

Pr e EQ

Pre FADER L

FADER(DCA)

METER

EQ OUT

BA L

Pre FADER R

Pre FADER L+R

Post ON R

Post ON L

Post ON L+R

Same as ST IN 1,2

TO AU X1-8

Same as ST IN 1,2

TO AU X9/10-19/20

FADER(DCA)

SE ND

( DCA CUE

Post PA N L

Post PA N R

AUX10

AUX2

AUX10

AUX9

AUX10

AUX2

AUX1

AUX2

ME TER

Post ON

METER

Post ON

CUE

Pre FADER L

Pre FADER R

Post ON L

Post ON R

( DCA CUE

Same as ST IN 1,2

CUE

TO FX1/FX2

FX1

SE ND

ST L

ST R

SUB

FX1

FX2

AUX10

AUX9

AUX20

AUX19

AUX1

AUX2

AUX8

CUE L

CUE R

AUX:Mono

COMBO JACK

+48V

Post PA N L

Post PA N R

USB IN 1-3 2

SUB

SUB LEV EL

SUB

SUB LEV EL

MA TR IX 1

MA TR IX 2

MA TR IX 3

MA TR IX 4

[INPUT1-16]

TF-RACK Mixer Block Diagram 1/2

Pr e EQ

Pr e EQ / Pr e Fader / Post ON

AUTOMIXER

Automix Gain

METER

CH1-8 Only

Pr e Fa de r / Po st ON

Pr e EQ / Pr e Fader / Post ON

Pr e EQ L Pr e EQ R

Pr e EQ L+R

Pr e EQ / Pr e Fader / Post ON L+R

Pr e EQ / Pr e Fader / Post ON L

Pr e EQ / Pr e Fader / Post ON R

Pr e EQ / Pr e Fader / Post ON L

Pr e EQ / Pr e Fader / Post ON R

Pr e EQ L Pr e EQ R

Pr e EQ L+R

Pr e Fa de r / Po st ON L+R

USB OUT 1-32,

SLOT OUT 1-32

-10dBV

PL AY BA CK R

[ST IN]

PL AY BA CK L

INPUT SEL ECT

USB IN 34

USB IN 33

INPUT SEL ECT

SLOT IN 64

SLOT IN 63

DIGITAL

GAIN

METER

Pr e DG

ME TER

Pr e Fa de r

[PHONES]

LEVEL

Pink Noise

Burst Noise

METER

OSC

OSCILLATOR

Sine Wave

ST L

ST R

SUB

AUX1

AUX2

AUX8

USB

HOST

I/F

REC L

REC R

PL AY BA CK L

PL AY BA CK R

[iPad]

[USB TO HOST]

PL AY BA CK L e ve l

AUX9

AUX10

AUX19

AUX20

OMNI OUT PATCH

CH1-32 Pre FADER

ST IN 1,2 Pre FAD E R

FX1,2 RTN Pre FADER

AUX1-8 Pr e FAD ER

AUX9-20 Pr e FAD E R

ST, SUB P re FA DE R

INPUT

SE LE CTOR

RTA

CUE

METER

Sample Rate

Convertor

ST L

ST R

SUB

FX1

FX2

AUX10

AUX9

AUX20

AUX19

AUX1

AUX2

AUX8

CUE L

CUE R

STEREO

4BAND

ME TER

Pr e EQ

FADER

ME TER

EQ OUT

ME TER

COMP OUT

BA L

CUE

COMP

GR METER

FlexGEQ

ME TER

Post ON

ME TER

GEQ O UT

GAIN

SUB

LPF

2BAND

METER

PRE LPF

FADER

ME TER

COMP OUT

COMP

GR METER

ME TER

Post ON

METER

EQ OUT

GAIN

Pr e Fader R

STE REO OUT R

STE REO OUT L

SUB OUT

AUX2 OUT

AUX1 OUT

AUX8 OUT

AUX10 OUT

AUX9 OUT

AUX19 OUT

AUX20 OUT

MO NITOR OUT L

MO NITOR OUT R

USB I/F

D I RE CT OU T 1 - 3 2

REC L

REC R

USB IN 1-3 4

STEREO OUT L/R

MATRIX OUT 1-4

SLOT

DIRE CT OUT 1-32 ( as SLOT OUT 1-32 )

AUX OUT 1-20 ( a s SLOT OUT 33-52 )

STE REO OUT L/R, SUB OU T, MO NITOR OUT

( as SLOT OUT 57,58,59,61,62 )

SLOT IN 1-32 ( as CH 1-32 INPUTs )

SLOT IN 63, 64( as ST IN 2 INPUTs )

MATRIX OUT 1-4 ( as SLOT OUT 53-56 )

MATRIX1

MATRIX2

MATRIX3

MATRIX4

MA TRIX1 OUT

MA TRIX2 OUT

MA TRIX3 OUT

MA TRIX4 OUT

TO MATRI X1-4

SE ND

MA TR IX 1-4

TF-RACK Mixer Block Diagram 2/2

Pr e Fa de r L

Post ON R

Post ON L

Post ON R

Post ON L

PA N

SE ND

Post ON R

Post ON L

BA L

Pr e Fa de r / Po st ON L

Pr e Fa de r / Po st ON R

CUE

MATRIX:STEREO

MATRIX:Mono

AUX1-8

4BAND

METER

Pr e EQ

FADER

METER

EQ OUT

ME TER

COMP OUT

COMP

GR METER

ME TER

Post ON

ME TER

GEQ O UT

GAINFlexGEQ

MATRI X1-4

FADER

ME TER

Post ON

DELAY

4BAND

METER

EQ OUT

GAIN

METER

Pr e EQ

PHONES LEVEL

MO NITOR LE VE L

MONITOR

SELECT

STE REO OU T

SUB OUT

ST IN

PLAY BA CK

USB IN 33,34

CUE LOGIC

ME TER

DELAY

MO NO

MONITOR / CU E

REC

SE LE CT

REC L

REC R

CUE

REC LEVEL

ME TER

ST L /R Pre FAD ER

AUX 1/2 Pr e FAD E R

AUX 3/4 Pr e FAD E R

MTRX 1/2 Pre FADER

MTRX 3/4 Pre FADER

Pr e Fa de r

Post ON

CUE

TO MATRI X1-4

SE ND

Post ON

SE ND

Post ON

Pr e Fa de r / Po st ON

CUE

MATRIX:Stereo

MATRIX:Mono

Pr e Fa de r Post ON

TO MATRI X1-4

Same as SUB

CUE

Same as SUB

4BAND

METER

Pr e EQ

COMP

GR METER

FADER

METER

EQ OUT

BA L

AUX9/10-19/20

ME TER

PRE FA DER

ME TER

Post ON

GAIN

ME TER

INSERT

EFFE CT

COMP OUT

Pr e Fa de r R

Pr e Fa de r L

Post ON R

Post ON L

Post ON R

Post ON L

Post ON R

SUB SE ND

TO MATRI X1-4

Same as STEREO

CUE

Same as STEREO

CUE

Pr e Fa de r / Po st ON

CUE

ME TER

Pr e Fa de r

Pr e Fa de r Post ON

AUX 5/6 Pr e FAD E R

AUX 7/8 Pr e FAD E R

[OMNI OUT 1]

+4dBu

[OMNI OUT 2]

+4dBu

[OMNI OUT 8]

+4dBu

TRIM

DATRIM

[OMNI OUT 9]

DATRIM

[OMNI OUT 10]

DATRIM

[OMNI OUT 16]

Published 02/2021 CR-J0

Manual Development Group

Yamaha Downloads

https://download.yamaha.com/

Yamaha Pro Audio global website

http://www.yamahaproaudio.com/

Yamaha TF1 Handleiding

Merk: Yamaha

Model: TF1

Categorie: DJ-controllers

Type: Handleiding

Deze handleiding is ook geschikt voor

Download PDF

rapport

in andere talen

English: Yamaha TF1 User manual
italiano: Yamaha TF1 Manuale utente
русский: Yamaha TF1 Руководство пользователя
français: Yamaha TF1 Manuel utilisateur
español: Yamaha TF1 Manual de usuario
Deutsch: Yamaha TF1 Benutzerhandbuch
português: Yamaha TF1 Manual do usuário
dansk: Yamaha TF1 Brugermanual
suomi: Yamaha TF1 Ohjekirja
čeština: Yamaha TF1 Uživatelský manuál
svenska: Yamaha TF1 Användarmanual
Türkçe: Yamaha TF1 Kullanım kılavuzu
polski: Yamaha TF1 Instrukcja obsługi
română: Yamaha TF1 Manual de utilizare

Yamaha TF1 Handleiding

Deze handleiding is ook geschikt voor

Yamaha TF1 Handleiding

in andere talen

Gerelateerde artikelen

Andere documenten