Documenttranscriptie

DTX700K Digital Musical Instruments Division ©2011 Yamaha Corporation WW60760 110PO***.*01C0 Assembly Manual EN This pamphlet describes the standard procedure for DTX700K assembly. After assembling the parts and connecting the cords as shown below, you will be ready to turn on the drum trigger module. 1 2 Assemble the RS500 Rack System. For details, refer to the assembly manual that came with the rack system. Check the contents of each package. Package 1: DTP700C  PCY135 Cymbal Pad (x2) Standard Assembly Example  RHH135 Real Hi-hat Pad (x1) Package 2: DTP700P  Stand base for the RHH135 (x1)  XP70 Tom Pad (x3)  HS650A Hi-hat Stand (x1)  XP80 Snare Pad (x1)  KP65 Kick Pad (x1) IMPORTANT PCY135 (Cymbal Pad) • For assembly, you will require four individual packages – an RS500 Rack System, a DTP700C Pad Set, a DTP700P Pad Set, and a DTX700 Drum Trigger Module. PCY135 (Cymbal Pad) • This pamphlet describes how to attach the pads and drum trigger module to the RS500 Rack System. Before carrying out the procedures described below, ensure that you have correctly assembled the rack system as described in its assembly manual. XP70 (Tom Pad) RHH135 (Real Hi-hat Pad) DTX700 Drum Trigger Module XP70 (Tom Pad)  Hi-hat clutch for the RHH135 (x1)  Stoppers for the PCY135 (x2) NOTICE Before starting assembly, lay a drum mat (sold separately) on the floor. Alternatively, before setting up the HS650A Hi-hat Stand and KP65 Kick Pad, you can place the packages' cardboard boxes on the floor to protect it from damage.  Clamp bolts (x4)  Tuning key (x1)  Cable bands (x10)  XP70 and XP80 Owner’s Manual (x1)  KP65 Owner’s Manual (x1) Package 3: DTX700  Cable band for the RHH135 (x1)  DTX700 Drum Trigger Module (x1)  Felts for the PCY135 (x2)  9-channel snake cable (x1) HS650A (Hi-hat Stand)  Module stand (x1)  AC power adaptor* (x1)  Module stand fastening screws (x4) RS500 (Rack System) KP65 (Kick Pad) * May not be included depending on your particular area. Please check with your Yamaha dealer.  DTX700 Owner’s Manual (x1)  DTX700 Data List (x1)  DVD (containing software) (x1)  PCY100, PCY135, and PCY155 Owner’s Manual (x1)  RHH135 Owner’s Manual (x1)  Assembly Manual (this pamphlet) XP80 (Snare Pad) 3 PRECAUTIONS Mount the pads and the drum trigger module on the rack system. As described below, mount the pads and the trigger module on the rack system, and then position the kick pad and the hi-hat. Mounting snare and tom pads Before using, please read this assembly manual, and use this product in a safe and proper manner. 2. Mount the snare pad on the rack’s clamp rod. As * Please keep this manual in a safe place for future reference. * Make sure to read the Assembly Manual of the Rack System and the Owner’s Manual of the Pad. XP70 WARNING If this symbol is ignored and the equipment is used improperly, fatal injury to persons or serious damage could occur. CAUTION If this symbol is ignored and the equipment is used improperly, there is a danger or injury to persons handling the equipment, and material damage could occur. • Do not let small children assemble or set up this product by themselves, or they may be injured. Always assemble this product with adult supervision. • Watch your fingers when adjusting clamps. They may become pinched, resulting in injury. • Be careful with the edges of the Cymbal Holders and the Tom Holders. The sharp holder ends may result in injury. • Be careful around pipe ends, inside the pipe and screw ends. Metal shavings, etc. may injure your fingers. shown below, ensure that the rod section is fully inserted into the pad’s mounting hole, and then fully tighten the clamp bolt. XP80 Snare pad Clamp rod  Mounting the tom pad 1. As with the snare pad, attach the clamp bolt to each of the three tom pads and provisionally tighten (by 5 or 6 turns). 2. Mount the three tom pads on the rack’s clamp rods. As shown below, ensure that the rod section is fully inserted into each pad’s mounting hole, and then fully tighten the clamp bolt. Rod section Tom pad Insert • Be careful with the edges of the spurs attached to the Kick Pad and foot pedal. The sharp ends may result in injury. • Do not put your hands or feet under the foot pedal or foot switch. They may be pinched, resulting in injury. • If this product is used with a Rack System or Cymbal Stand, make sure all bolts are tightened firmly. Also, when adjusting the height or angle, do not suddenly loosen the bolts. Loose bolts may result in the rack overturning or parts dropping, causing injury. • Do not attach acoustic drums to the electronic drum rack. Clamps may be damaged and drums may drop, causing injury. • Always set the product on a flat and solid surface. Placement on a sloping, unstable surface or on steps may result in the product being unstable and subject to overturning. • When setting up the product, please pay close attention to the handling and setting of cables. Carelessly placed cables may cause the user and others to trip and fall. • Do not alter the product. Doing so may result in injury or damage/deterioration to the product. • Do not sit or step on the rack. The rack may overturn or be damaged, resulting in injury. NOTICE • Make sure you hold onto the plug, not the cable, when connecting or disconnecting the cable. Also, never place any heavy or sharp objects on the cable. Applying excessive force to the cable may result in damage to the cable, such as the wires being severed, etc. • Do not step on or place heavy objects on the product. It may result in damage. • Do not use or keep the product in places with extremely high temperature (places in direct sunlight, close to a heater, in a closed car, etc.) or high humidity (bathroom, outside on a rainy day, etc.). Doing so may result in deformation, discoloration, damage or deterioration. • When cleaning the product, do not use benzine, thinner or alcohol as it may result in discoloration or deformation. Please wipe with a soft cloth or a damp cloth that has been wrung out thoroughly. If the product is soiled or sticky, use a neutral detergent on a cloth then wipe with a damp cloth that has been wrung out thoroughly to remove any remaining detergent. Also pay close attention so as not to let the water and detergent come into contact with the cushions used in the product; doing so may result in deterioration. * Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer. Rod section Clamp rod Clamp bolt Insert 3. If necessary, use clamp bolts A to E to adjust the  Mounting the snare pad 1. Attach the clamp bolt to the snare pad and provisionally tighten (by 5 or 6 turns). Clamp bolt (to be tightened in the direction shown) Snare pad (rear side) height and angle of the snare pad. When doing so, be sure to adjust one bolt at a time (i.e., loosen a bolt, adjust the pad, and then retighten before loosening another). Clamp bolt B Clamp bolt 3. If necessary, use clamp bolts A to D to adjust the height and angle of any of the pads. When doing so, be sure to adjust one bolt at a time (i.e., loosen a bolt, adjust the pad, and then retighten before loosening another). Clamp bolt D Clamp bolt E Clamp bolt B Clamp bolt A Clamp bolt A Clamp bolt C Clamp bolt C Clamp bolt D Continued on other side  Mounting the drum trigger module and cymbal pads Assembling the kick pad  Mounting the cymbal pads PCY135 PCY135 1. Using a tuning key, loosen the stopper’s key bolt. 5. Secure the stopper in place. With the stopper making full contact with the bottom surface of the bolt cover, tighten the stopper’s key bolt using a tuning key. If a drum mat (sold separately) is not available, lay a sheet of cardboard on the floor to protect it from scratching. Spring washer 2. Remove the wing bolts, spring washers, and washers from the kick pad body, and Key bolt Washer Wing bolt line up each set nearby in the order in which it was removed. 3. Join the base section to the body as shown right, and then secure it in place by Stopper Drum trigger module 1. assembling the wing bolts, spring washers, and washers removed in the previous step from the base side. Bolt cover Body Body Full contact Stopper Tuning key Base Cymbal holder 2. Remove the wing nut, the two felt pads, and the bolt cover from the cymbal holder. 6. Place one of the felt pads removed in Step 2 on the cymbal holder. Wing nut Bolt cover Mount the pad unit on the cymbal stand. Lower the pad unit into place with the cymbal holder’s shaft passing through the central hole of the cup section. When mounted, the stopper’s pin should rest inside the pad unit’s smaller hole. Cymbal holder * If you were to play a cymbal pad without the stopper’s pin positioned inside the smaller hole, the pad could rotate, causing the cable to be pulled out. It is very important, therefore, to ensure that the stopper is secured as described in Step 5 above. Felt pads  Mounting the drum trigger module 1. 7. Attach the module stand (provided) to the underside of the drum trigger module using the module stand fastening screws. Module stand fastening screws 4 Position the hi-hat stand and kick pad as desired, referring to the standard assembly example on the other side. 5 Connect the pads to the drum trigger module. 1. 8. Assemble the felt pad that came with your pad unit. Module stand 3. Place the stopper on the cymbal holder. Drum trigger module (back side) * If the key bolt was not sufficiently loosened in Step 1 above, it may not be possible to pass the stopper over the cymbal holder’s shaft. In such a case, loosen the key bolt as much as possible without removing it. Front of module * The second felt pad removed from the cymbal holder in Step 2 above is not required for assembly of your pad unit. Insert the 9-channel snake cable’s straight plugs into the drum trigger module’s trigger input jacks ([q SNARE] to [o KICK/!0] and [HI-HAT CONTROL]). • If you are using the standard setup, the stickers on each of the snake cable’s plugs will indicate the name of the corresponding pad. 9 Pad unit Felt pad that came with pad unit Smaller hole [9-channel snake cable] Pad unit Stopper Straight plugs Drum trigger module + module stand Felt pad Cymbal holder Insert Bolt cover 6 Assembling the hi-hat stand 5. As shown on the right, loosen the wing bolt (b in the figure) to remove the hi-hat clutch. * This hi-hat clutch is not used within the standard assembly example shown in this pamphlet. Instead, use the hi-hat clutch that came with your RHH135. 2. Loosen the hi-hat stand’s wing bolt (a in the following figure). 3. Extend the tripod legs to stabilize the stand. 6. Pull out the hi-hat shaft Retighten the wing bolt loosened in Step 2. 4. Insert the radius rod into the frame hole as shown below. 1. Hi-hat clutch Felt washer Screw the hi-hat shaft pipe . from the upper pipe into the nut on the lower No 6 Connection 5 4 3 2 1 Straight plug names (as shown on stickers) DTX700 jack names SNARE TOM1 TOM2 TOM3 RIDE CRASH HI HAT HH CON KICK 1: qSNARE 2: wTOM1 3: eTOM2 4: rTOM3 5: tRIDE 6: yCRASH1 7: iHI-HAT 8: HI-HAT CONTROL 9: oKICK/!0 3. In the case of snare and tom pads, wrap the cables around the cable clips to prevent them from being pulled out. NOTICE Excessive bending can damage the pad cables. Ensure, therefore, that these cables are not bent at an extreme angle when wrapped around the clips. Connect the drum trigger module to a power supply. Insert the power adaptor’s DC plug into the connector. Hook the power adaptor’s cord around the cord clip to secure it in place. [Drum trigger module’s rear panel] b . 7. 7 HH CON HI HAT CRASH KICK SNARE TOM1 TOM2 TOM3 RIDE Cymbal holder * When assembling the bolt cover, turn until it no longer rotates. 8 L-shaped plugs Clamp bolt If a drum mat (sold separately) is not available, lay a sheet of cardboard on the floor to protect it from scratching. [Locations of pad jacks] Pin Stopper Holder clamp 2. Plug the 9-channel snake cable’s L-shaped plugs into the correct pads. [Drum trigger module’s rear panel] Stopper’s pin tighten the clamp bolt to secure in position. 1. As described below, connect the output of each pad to the corresponding trigger input jack on the drum trigger module. cymbal holder. Wing nut Bolt cover Before starting assembly, lay a drum mat (sold separately) on the floor. Alternatively, you can place the packages' cardboard boxes on the floor under the hi-hat stand and kick pad to protect it from damage. 9. Tighten the wing nut to secure the pad unit to the 4. Replace the bolt cover. 2. Place the module stand inside the holder clamp and NOTICE Support plate Support plate connector Cord clip c 8. Insert the upper pipe into the hi-hat shaft from above, and then tighten the wing bolt (c in the figure) with the support plate positioned at the middle area of the hi-hat shaft . Wing bolt a 2. Use the cable bands to bind the cables to the rack as shown on the right. ( 9. Remove the felt washer located above the support 3. Plug the AC power adaptor into an AC wall socket. plate. It is not used within the standard assembly example shown in this pamphlet. Radius rod Radius rod ) 10. Set up the RHH135 Real Hi-hat Pad. * Refer to refer to the Setting Up section of the owner’s manual that came with your RHH135. This completes the assembly procedure. * For information about tuning the power on/off, checking the actual sound, and other subsequent steps, refer to the Setting Up section of the owner’s manual that came with your drum trigger module.