1
Thank you for purchasing the Yamaha ELECTRONIC DRUM KIT DTX6K3-X or DTX6K2-X. This electronic drum kit can be used in your home or a studio, or onstage for live perfor-
mances. For proper assembly and safe use, please read this assembly manual carefully before using it. After you have read the manual, keep it in a safe and handy place for future ref-
erence.
This manual describes the standard assembly procedure for the DTX6K3-X/DTX6K2-X electronic drum kits. It covers assembly, wiring and setting up the drum trigger module of the kit
as shown below.
The illustrations show the DTX6K3-X electronic drum kit, but the information applies to the DTX6K2-X (except where indicated).
ELECTRONIC DRUM KIT
DTX6K3-X DTX6K2-X Assembly Manual
EN
This manual describes the process of assembling a pad set and drum trigger mod-
ule to an already assembled RS6 Electronic Drum Rack. Before starting the steps
below, therefore, be sure to assemble your RS6 as described in the Owner’s Man-
ual that came with it.
Lay a drum mat (sold separately) on the floor underneath the hi-hat stand and the
kick pad. Alternatively, you can place cardboard from the drum kit packaging or the
like on the floor to prevent it from being scratched.
IMPORTANT
NOTICE
Example of standard assembly
Cymbal pad
Tom pads
Kick pad
Snare pad
Hi-hat stand
DTX-PRO
Drum trigger module
Real hi-hat pad
Cymbal pad
Tom pad
Cymbal pad
Electronic drum rack
The purpose of the precautions detailed below is to ensure that this electronic drum kit can be used safely without fear of injury or property damage. As a means of indicating the severity and immediacy
of any risk of injury or property damage resulting from incorrect operation, these precautions are classified as either WARNING or CAUTION. The instructions displayed together with these precautions
are extremely important in terms of ensuring safety, and therefore, they should be fully observed.
* After reading this Assembly Manual, ensure that it is kept in a safe, convenient location for future reference.
* Be sure to also read the Assembly Manuals and/or Owner’s Manuals that came with your pads and rack.
* The illustrations as shown in this manual are for instructional purposes only, and may appear somewhat dif-
ferent from those on your instrument.
* The company names and product names in this manual are the trademarks or registered trademarks of their
respective companies.
* The contents of this manual apply to the latest specifications as of the publishing date. To obtain the latest
manual, access the Yamaha website then download the manual file. Since specifications, equipment or sep-
arately sold accessories may not be the same in every locale, please check with your Yamaha dealer.
NOTICE: Usage Precautions
• When connecting and disconnecting cables, be sure to hold the plug and not the cable itself. In addition,
avoid placing heavy items on top of cables and do not allow them to touch sharp edges. Failure to avoid
these precautions can lead to cable breakage and disconnection.
• Do not climb onto the electronic drum kit and avoid placing heavy objects on it. Failure to observe this pre-
caution can result in malfunction.
• Avoid using or storing the electronic drum kit in very hot locations (i.e., in direct sunlight, in close proximity to
a heater, or in a closed vehicle) or in highly humid locations (i.e., in a bathroom or outdoors in wet weather).
Failure to observe this precaution can lead to warping, discoloration, malfunction, or breakdown.
• Avoid cleaning the electronic drum kit with organic solvents, paint thinner, or alcohol as these substances
can cause warping and discoloration. Instead, we recommend you remove dust using a soft dry cloth or
wipe clean using a moist, tightly-wrung cloth. If the electronic drum kit is very dirty, first wipe the dirt away
using a cloth moistened with a neutral detergent solution and tightly wrung. Following this, wipe away the
detergent solution using a cloth soaked in water and tightly wrung.
PRECAUTIONS Please read carefully before proceeding
Failure to observe the precautions described below can result in
serious injury or even death.
• Young children using this electronic drum kit should be supervised by a guardian to eliminate any
possibility of injury.
• Holders for cymbal and tom pads have sharp tips. In order to avoid injury, therefore, you should
take special care whenever handling these components.
• The anti-slip stoppers on kick pads and foot pedals have sharp tips. In order to avoid injury, there-
fore, you should take special care whenever handling these components.
• Be sure to securely tighten nuts and other fasteners when setting up this electronic drum kit. In
addition, be sure to proceed slowly when loosening nuts. If this precaution is not observed, pads
may fall off or the rack may collapse or fall over, possibly causing injury.
• Do not setup this electronic drum kit on a slope, on an unstable platform, or on any other unsafe
surface. If this precaution is not observed, it may topple over or fall, possibly causing injury.
• Whenever setting up this electronic drum kit, ensure that cables and the like are arranged safely. If
someone were to trip on a cable, the kit could topple over and cause injury.
• Under no circumstances should this electronic drum kit be disassembled or customized. Failure to
observe this precaution can result in injury or malfunction.
• Do not sit or stand on the rack. Doing so could cause it to fall over or break, possibly causing injury.
WARNING
Failure to observe the precautions described below can result in
injury and/or property damage.
• Mind your fingers when adjusting clamps. They can easily be crushed if care is not taken during
this operation.
• Be careful with the tips of supports, arms, screws, and the like. Fingers can easily be injured by
sharp tips if these components are not handled carefully.
• Do not place hands or feet under a kick pad or foot pedal. Doing so could result in injury.
• Do not use the electronic drum kit’s rack to hold acoustic drums. Doing so could cause clamps to
break and the drums to fall off, which in turn could lead to injury.
CAUTION
Manual Development Group
© 2020 Yamaha Corporation
Published 04/2020
POMA*.*- **A0
VCR2600
Open the boxes to reveal their contents.
After opening up the packages containing your electronic drum kit, please verify that all of the following components are present.
Assemble the RS6 Electronic Drum Rack.
For instructions on how to assemble the RS6 Electronic Drum Rack, refer to the Owner’s Manual that came with it.
Assemble the pads and the drum trigger module to the electronic drum rack.
1
Components of both DTX6K3-X and DTX6K2-X
XP80 Snare Pad
(×1)
PCY135 Cymbal Pad
(×3)
RHH135 Real
Hi-hat Pad (×1)
Stand base for
RHH135 (×1)
RS6 Electronic Drum Rack (×1)
RS6 Owner’s Manual (×1)
HS650A Hi-hat
Stand (×1)
KP90 Kick Pad (×1)
Ten-channel snake cable (×1)
Stopper for
PCY135 (×3)
Cable band
(×9)
Cable band for
RHH135 (×1)
DTX6K3-X DTX6K2-X Assembly Manual
(this leaflet; ×1)
PCY100 PCY135 PCY155 Owner’s Manual
(×1)
RHH135 Owner’s Manual (×1)
XP70 XP80 Owner’s Manual (×1)
KP90 Owner’s Manual (×1)
DTX-PRO Drum Trigger Module
(×1)
AC adaptor (×1)
* May not be included depending on
your particular area. Please check
with your Yamaha dealer.
DTX-PRO Owner’s Manual (×1)
Cubase AI Download information
(×1)
Module holder (×1)
Module holder screw (×4)
XP70 Tom Pad (×3)
Clamp bolt
(for XP70 or XP80; ×4)
Hi-hat clutch for
RHH135 (×1)
Drum key (×1)
Anti-slip stoppers for
KP90 (incl. springs) (×2)
DTX6K3-X only DTX6K2-X only
TP70 Tom Pad (×3)
Clamp bolt
(for XP80; ×1)
Wing bolt
(for TP70; ×3)
TP70 Owner’s Manual
(×1)
2
3
Snare pad
1. Attach a clamp bolt to the snare pad and provisionally tighten
(by five or six turns).
2. Attach the XP80 snare pad to the rod, and then tighten the
clamp bolt to secure the snare pad.
3. Loosen bolts A to D as shown below to adjust the height and
angle of the snare pad. When correctly positioned, be sure to
securely retighten the bolts before proceeding to the next
step.
Tom pads
1. As with the snare pad, attach a clamp bolt (for XP70) or wing
bolt (for TP70) to each of the three tom pads and provisionally
tighten (by five or six turns).
2. Push each of the tom pads onto one of the rack’s tom holders.
Each time, ensure that the tom holder’s rod is fully inserted
into the tom pad’s mounting hole, and then tighten the bolt to
secure the pad in place.
3. Loosen bolts A to C as shown below to adjust the height and
angle of each tom pad. When correctly positioned, be sure to
securely retighten the bolts before proceeding to the next
step.
XP80
snare pad
DTX6K3-X: XP70
DTX6K2-X: TP70
tom pads
Clamp bolt
(tighten in the direction of
the arrow)
XP80 snare pad (rear side)
Leave a gap of about a half inch
between the base of the rod and
the snare pad. Contact between
the rod section and snare pad
may cause damage to the pad.
Insert
XP80 snare pad
Rod section
Clamp bolt
NOTICE
Bolt A
Bolt C
Bolt D
Bolt B
XP70
tom pad
Insert
Clamp bolt
Tom holder
Rod section
DTX6K3-X DTX6K2-X
TP70
tom pad
Wing bolt
Tom holder
Rod section
Insert
Bolt B
Bolt C
Bolt A
* DTX6K3-X shown.
Assembling the snare and tom pads
Continued on other side
2
1. If a drum mat (sold separately) is not available, lay a sheet of
cardboard on the floor to prevent it from being scratched.
2. Loosen the hi-hat stand’s wing bolt a.
3. Open up the three legs as shown below and then retighten
the wing bolt a to lock them in place.
4. Insert the footboard stabilizer rods into the frame holes as
shown below.
5. Loosen the hi-hat clutch’s wing bolt b and remove the hi-hat
clutch.
* The hi-hat clutch is not required when assembling the elec-
tronic drum kit in the standard fashion described in this
manual. Instead, the hi-hat clutch that came with the
RHH135 Real Hi-hat Pad will be used.
6. Remove the hi-hat shaft from the upper tube .
7. Insert the hi-hat shaft removed in Step 6 as far as it will
go into the lower tube and screw in the tip.
8. Insert the upper tube over the hi-hat shaft and tighten
the wing bolt c to secure it in place with the cymbal support
plate approximately half way between the top of the lower
tube and the top of the hi-hat shaft .
9. Remove the felt pad attached above the cymbal support
plate. It is not required when assembling the electronic drum
kit in the standard fashion described in this manual.
10. Assemble the RHH135 Real Hi-hat Pad.
* For detailed instructions, refer to the “Setting Up” in the
RHH135 Owner’s Manual.
Footboard
stabilizer rod
Wing bolt a
Footboard
stabilizer rod
Felt washer
Hi-hat clutch
Cymbal
support
plate
Cymbal
support plate
c
b
Assembling the hi-hat stand
Drum trigger module
1. Secure the module holder to the bottom of the drum trigger
module using the module holder screws.
2. Push the module holder into the holder clamp and tighten the
clamp bolt to secure it in place.
Cymbal pads
1. Using the drum key, loosen
the stopper’s key bolt.
2. Remove the wing nut, the two felt
pads, and the bolt cover from the
cymbal holder.
3. Place the stopper on the cymbal holder.
* If the key bolt was not sufficiently loosened in Step 1
above, it may not be possible to pass the stopper over the
cymbal holder’s shaft. In such a case, loosen the key bolt
as much as possible without removing it.
4. Replace the bolt cover.
* Turn the bolt cover to tighten it
onto the threaded section and
firmly secure it in place.
5. With the stopper making full contact with the bottom surface
of the bolt cover as shown below, tighten the stopper’s key
bolt using the drum key.
6. Place one of the felt pads removed in Step 2 on the cymbal
holder.
7. Mount the pad on the cymbal stand. Lower the pad into place
with the cymbal holder’s shaft passing through the central
hole. When mounted, the stopper’s pin should rest inside the
pad’s smaller hole.
* If you were to play your cymbal pad without the stopper’s
pin positioned well inside the smaller hole, the pad could
rotate, causing the pin to be pulled out. It is very important,
therefore, to ensure that the stopper is secured as shown
in Step 5 above.
8. Assemble the other felt pad removed in Step 2 to the cymbal
holder.
9. Tighten the wing nut to secure the pad to the cymbal holder.
PCY135
cymbal pad
Drum trigger
module
PCY135
cymbal pad
Module holder screw (×4)
Module holder
Drum trigger module
(rear side)
Clamp bolt
Drum trigger module
+
module holder
Insert
Holder clamp
Key bolt
Drum key
Stopper
Cymbal
holder
Felt pads
Bolt cover
Wing nut
Cymbal
holder
Stopper
Bolt
cover
Threaded
section
Cymbal holder
Stopper
Bolt cover
Full contact
Drum key
Cymbal pad
Felt pad removed
in Step 2
Cymbal holder
Felt pad removed
in Step 2
Bolt cover
Cymbal pad
Stopper
Pin
Wing nut
Stopper’s pin
Smaller hole
Assembling the drum trigger module and cymbal pads
1. If a drum mat (sold separately) is not available, lay a sheet of cardboard on the floor to prevent
it from being scratched.
2. Remove the two wing bolts from the kick pad frame, and then place them nearby.
3. Join the base to the frame as shown on the right, and then secure it in place by the wing bolts
removed in the previous step from the base side.
NOTE
For details on assembling the foot pedal (sold separately), refer to the “Assembling the KP90” in the
KP90 Owner’s Manual.
Assembling the kick pad
Frame
Frame
Wing bolt
Base
Arrange the hi-hat stand and the kick pad as shown in Example of standard assembly on the other side of this sheet.
• Lay a drum mat (sold separately) on the floor underneath the hi-hat stand and the kick pad. Alternatively, you can place cardboard from the drum kit packaging or the like
on the floor to prevent it from being scratched.
• Ensure that you do not lower the electronic drum rack’s center strut too much as doing so may cause it to come into contact with the kick pad.
Connect the pads to the drum trigger module.
As described below, connect the output of each pad to the corresponding trigger input jack on the drum trigger module.
Connect the drum trigger module to a power supply.
Setting up the drum trigger module.
4
NOTICE
5
4. Using the cable bands, secure the cables to the electronic drum rack at the positions circled in the figure on the right. ( )
If you secure the cable band from the side closer to the drum trigger module, you can make connections more
easily.
RIDE CRASH2 TOM3TOM2TOM1 KICKSNARE CRASHHH CON HI HAT
KICK HH CON HI HAT CRASH2 CRASH RIDE TOM3 TOM2 TOM1 SNARE
CRASH2
CRASH
KICK
SNARE
RIDE
TOM3
TOM2
TOM1
HI HAT HH CON
Trigger input jacks on the drum module
Ten-channel snake cable
1. Plug the straight ends of the ten-channel snake cable into the trigger input jacks on the back of the drum trigger module.
• When using the standard setup, the stickers on each of the snake cable’s plugs will indicate the name of the corresponding pad.
2. Plug the L-shaped ends of the ten-channel snake cable into the corresponding pads.
3. Wrap the cables for the snare pad, the tom pads, the cymbal pads and the hi-hat pad around the cable clips to prevent them from being pulled out.
Excessive bending can damage pad cables. Ensure, therefore, that these cables are not bent at an extreme angle when wrapped around the clips.
NOTICE
6
1. Plug the AC adaptor’s DC cord into the connector. Hook the AC
adaptor’s DC cord around the cord clip to secure it in place.
CAUTION
Excessive bending can damage AC adaptor’s DC cord. Ensure, there-
fore, that the cord is not bent at an extreme angle when wrapped
around the clips. Doing so can cause fire or electrical shock.
Cord clip
connector
2. Plug the adaptor’s AC cord into a domestic wall
socket.
7
According to your particular electronic drum kit, select the “DTX6K3-X” or the “DTX6K2-X” trigger
setup on your drum trigger module. (For details on the trigger setup procedure, refer to the “Initial
Settings (Trigger Setup Wizard)” in the DTX-PRO Owner’s Manual.)
• Kick pad output (LEVEL) adjustment:
Adjust the trigger output to your desired setting by using the KP90 kick pad’s level adjustment knob.
For details, refer to the “Adjusting the Output Level” in the KP90 Owner’s Manual.
The selection of the trigger setup is very important. Selecting the wrong trigger setup
will adversely affect your ability to perform comfortably. Use the correct trigger setup
that corresponds to your particular electronic drum kit for optimum performance.
• You can play comfortably by striking near the YAMAHA logo. Adjust the height, angle and ori-
entation of the cymbal pad and hi-hat pad to a position where you can hit around the YAMAHA
logo naturally when performing. The correct setting position is that the YAMAHA logo of the
cymbal pad and hi-hat pad are visible in front of the performer. The direction of the cymbal pad
will be appropriate by adjusting the direction of the stopper as shown on the right. The direction
of the hi-hat pad will also be appropriate by adjusting the direction of the hi-hat clutch.
• The hi-hat shaft will become loose while you continue to use the hi-hat, and the hi-hat pad may
rotate. Since this may adversely affect performance, screw in the hi-hat shaft periodically and
adjust the position of the hi-hat pad.
IMPORTANT
Stopper’s pin
YAMAHA logo
Hi-hat shaft
Screw in
Your electronic drum kit is now ready. * For instructions on turning on the drum trigger module, producing sounds, and other subsequent steps,
please refer to the Owner’s Manual that came with the module.
-
1
-
2
Yamaha DTX6K Handleiding
- Type
- Handleiding
- Deze handleiding is ook geschikt voor
in andere talen
- English: Yamaha DTX6K User manual
- italiano: Yamaha DTX6K Manuale utente
- français: Yamaha DTX6K Manuel utilisateur
- español: Yamaha DTX6K Manual de usuario
- Deutsch: Yamaha DTX6K Benutzerhandbuch
- português: Yamaha DTX6K Manual do usuário
- dansk: Yamaha DTX6K Brugermanual
- čeština: Yamaha DTX6K Uživatelský manuál
- polski: Yamaha DTX6K Instrukcja obsługi
- română: Yamaha DTX6K Manual de utilizare