AEG FAV50860I-B Handleiding

Merk: AEG

Model: FAV50860I-B

Categorie: Vaatwassers

Type: Handleiding

Deze handleiding is ook geschikt voor

FAVORIT 50860 i

Dishwasher

User Instructions

Dear customer,

Please read these user instructions carefully.

Above all please observe the safety instructions on the first few pages

ofthese user instructions! Please keep these user instructions for later

reference. Pass them on to any subsequent owner of the appliance.

The warning triangle and/or specific words (Warning!, Caution!,

Important!) are used to highlight instructions that are important for

your safety or for the function of the appliance. It is imperative that

these instructions are observed.

0 This symbol or numbered instruction steps lead you step for step

through the operation of the appliance.

Next to this symbol you receive additional information and practical

tips on using the appliance.

Tips and instructions for the economical and environmentally conscious

use of the appliance are marked with a clover leaf.

In the event of a malfunction, these operating instructions contain

information on how to rectify faults yourself, see the "What to do, if..."

section.

If these instructions are insufficient, please contact your nearest cus-

tomer service centre.

In the case of technical problems, our customer service organisation is

available to provide you with assistance at any time (you will find

addresses and telephone numbers in the "Customer Service Centres"

section).

In this respect please read the "Service" note on the rear of these user

instructions.

Your dishwasher is fitted with the new "PULSE WASH" wash system.

With this wash system, the motor speed and spray pressure are

varied during the wash programme to improve the cleaning of the

dishes. It is for this reason that the noise level changes during the

wash programme.

nte

on paper manu

acture

env

ronmenta

y soun

processes.

He who thinks ecologically acts accordingly ...

Contents

CONTENTS

Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Economical and Ecological Dishwashing . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Appliance Features and Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Prior to using for the first time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Water softener . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Set water softener . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Special salt for the water softener . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Setting the amount of special salt to be added . . . . . . . . . . . . . . . . . . . 12

Adding special salt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Filling with Rinse Aid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Adjusting Rinse Aid Dosing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

In Daily Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Loading cutlery and dishes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Loading Cutlery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Loading Pans, Frying Pans and Large Plates . . . . . . . . . . . . . . . . . . . . . . 18

Loading Cups, Glasses and Coffee Services . . . . . . . . . . . . . . . . . . . . . . . 20

Adjusting the Height of the Upper Basket . . . . . . . . . . . . . . . . . . . . . . . 21

Filling with Detergent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Use of "3 in 1"/ Combi Detergent Tablets . . . . . . . . . . . . . . . . . . . . . . . . 23

Concentrated Detergent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Detergent tablets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Selecting the Wash Programme (Programme Table) . . . . . . . . . . . . . . . . . . 25

Starting a dishwashing cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Changing/interrupting/aborting a dishwashing cycle . . . . . . . . . . . . . . 26

Setting or changing the start delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Load Sensing – Sensor Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Switching Off the Dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Emptying the Dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Care and Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Cleaning the Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Contents

What to do, when ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

...Error messages are displayed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

...problems occur during use of the dishwasher. . . . . . . . . . . . . . . . . . . . . . 33

...the wash results are not satisfactory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Notes for Test Institutes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Installation and Connection Instructions . . . . . . . . . . . . . . . . 36

Installing the Dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Dishwashers That Can Be Integrated . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Connecting the Dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Water Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Permitted water pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Connect the inlet hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Water drain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Leak Prevention System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Service Departments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Guarantee Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Operating Instructions

OPERATING INSTRUCTIONS

1 Safety Instructions

The safety aspects of AEG electrical appliances comply with accepted

technical standards and the German Appliance Safety Law. Neverthe-

less, as a manufacturer we consider it our obligation to make you

aware of the following safety information:

Installation, Connection and Placing into Operation

• The dishwasher may only be transported upright.

• Check the dishwasher for transport damage. Do not in any circum-

stances connect an appliance that is damaged. In the case of damage,

please contact your supplier.

• Prior to placing the appliance in operation, ensure that the nominal

voltage and type of supply on the rating plate match that of the sup-

ply where the appliance is to be installed. The fuse rating is also to be

found on the rating plate.

• For information on how to correctly install and connect up your dish-

washer, please read the „Installation“ section. Multiway plugs / con-

nectors and extension cables must not be used. This could constitute

a safety hazard.

Child Safety

• Children often do not recognise the hazards associated with the use

of electrical appliances. It is therefore important that you ensure

children are adequately supervised and that you do not allow chil-

dren to play with the dishwasher – there is a risk that children can

shut themselves inside the appliance (risk of suffocation!).

• Packaging materials (e.g. films, styrofoam) can be dangerous for chil-

dren. Risk of suffocation! Keep packaging away from children.

• Detergents can cause burns to the eyes, mouth, and throat, or even

cause choking! Please observe the manufacturer's safety instructions

for cleaners and detergents.

• The water in your dishwasher is not suitable for drinking. If there are

still remnants of detergent in the appliance, there is a risk of burns!

• When disposing of the dishwasher: unplug from the mains, cut off

and dispose of the mains cable. Break the door lock so that the door

no longer shuts.

Operating Instructions

General Safety

• Repairs to the dishwasher are only to be carried out by qualified serv-

ice engineers. Improper repairs can give rise to significant hazards for

the user. If your appliance needs repairing, please contact customer

service or your dealer.

• Never place the dishwasher in operation if the mains cable, water

inlet or drain hose is damaged; or the control panel, work top or

plinth area is damaged such that the inside of the appliance is freely

accessible.

• If the mains lead is damaged, or is to be replaced for a longer lead,

the cable (obtainable from AEG customer service) must be replaced

by a service engineer authorised by AEG.

• Never unplug the appliance by pulling on the cable, always pull the

plug.

• Additions or modifications to the dishwasher are not permitted for

safety reasons.

• Ensure that the door of the dishwasher is always closed when it is not

being loaded or unloaded. In this way you will avoid anybody tripping

over the open door and hurting themselves.

• Sharp knives and other item of cutlery with sharp edges must be laid

in the upper rack or placed in the cutlery rack with the point facing

downwards.

Correct Use

• Only wash household dishes using the dishwasher. If the appliance is

used for other purposes, or is used incorrectly, the manufacturer can-

not accept any liability for any damage caused.

• Prior to use, ensure that the manufacturers of the special salt, deter-

gent, and rinse aid employed specifically permit the usage of their

products in household dishwashers.

• Do not put any solvents in the dishwasher. There is a risk of an explo-

sion!

• The anti-flood system provides dependable protection against dam-

age due to leaks. For this system to function correctly, the following

preconditions must be met:

– The appliance must remain connected to the mains even when it is

switched off.

– The dishwasher must be correctly installed.

– Always shut off the water supply at the tap when the dishwasher is

not to be used for longer periods, e.g. when you are away on holiday.

Operating Instructions

• Do not sit or stand on the open door, the appliance may tip over.

• In the event of a fault, first close the tap, then switch off the appli-

ance and unplug it from the mains. If the appliance is permanently

wired to the mains: switch off the fuse(s) or unscrew them.

2 Disposal

Disposing of the Packaging Material

Dispose of the dishwasher packaging material correctly. All the packag-

ing materials used are harmless to the environment and can be recy-

cled.

• Plastic parts are marked with standard international abbreviations:

– >PE< for polyethylene, e.g. sheet wrapping material

– >PS< for polystyrene, e.g. padding material (always CFC-free)

– >POM< for polyoxymethylene, e.g. plastic clips

• Cardboard packaging is manufactured from recycled paper and

should be deposited in the waste paper collection for recycling.

Disposal of old appliances

As and when you cease to use your dishwasher, please take it to a recy-

cling centre or to your dealer who will, for a small contribution to the

costs, dispose of it for you.

2 Economical and Ecological Dishwashing

• Only connect the dishwasher to the hot water supply if your hot

water is not electrically heated.

• Ensure that the water softener is correctly adjusted.

• Do not pre-rinse dishes under running water.

• When you wash a small load, the load sensor calculates the amount

of water necessary and shortens the programme. It is more economi-

cal to always wash with a full load.

• Select the wash programme to suit the nature and degree of the soil-

ing on the dishes.

• Do not use more detergent, special salt or rinse aid than is recom-

mended in these operating instructions and by the manufacturer of

the respective product.

Operating Instructions

Appliance Features and Control Panel

Top Spray Nozzle

Container for

Special Salt

Rating Plate

Container for

Rinse Aid

Filters

Rubber Seal for

Connecting the

Water Feed to

the Spray Arm

Spray Arms

Container for

Detergent

Water hardness switch

Operating Instructions

Control Panel

The control panel consists of the ON/OFF button M and the pro-

gramme buttons with LED displays.

Function buttons: In addition to the stated wash programme the fol-

lowing functions can also be set using these buttons:

The Multi-Display can display,

– the hardness setting to which the water softener is set.

– the start delay that is set.

– how long the current wash programme can be expected to last.

– which fault has occurred on the dishwasher.

Indicators have the following significance:

Function Button 1 Adjust the water softener

Function Button 2 - is not occupied -

Function Button 3 - is not occupied -

Function Button 4 - is not occupied -

Refill with special salt

Refill with rinse aid

Multi-Display

Control Panel

Indicators

Set Start Delay

Function Buttons

Door Handle

Function Buttons

Operating Instructions

Prior to using for the first time

Prior to using for the first time, remove all the clips with which the dish

racks are secured for transport.

Then perform the following steps:

0 1. Adjust the water softener

2. Fill with Special Salt for the Water Softener

3. Fill with Rinse Aid

Special salt and rinse aid must not be added if you use 3-in-1 detergent

tablets.

Water softener

To avoid scale deposits on the dishes and in the dishwasher, the dishes

must be washed with soft water, i.e. water with a low lime content. The

dishwasher therefore has a built-in water softener, in which tap water

with a hardness of 4°d (German degree) and harder is softened with the

aid of special salt.

Your water supplier will be able to inform you about the hardness and

hardness range of the water in your area.

The water softener can be set manually using the water hardness

switch; it can also be set electronically using the buttons on the control

panel.

Water hardness

Adjusting the hardness

setting

Indication on

the multi-dis-

play

In °d

In mmol/l

Range Manually Electronically

51 - 70

43 - 50

37 - 42

29 - 36

23 - 28

9,0 - 12,5

7,6 - 8,9

6,5 - 7,5

5,1 - 6,4

4,0 - 5,0

10L

19 - 22

15 - 18

3,3 - 3,9

2,6 - 3,2

III

11 - 14 1,9 - 2,5 II 3

4 - 10 0,7 - 1,8 I/II 2

under 4 under 0,7 I

no salt

necessary

Operating Instructions

Set water softener

Using the table as a guide, adjust the water softener to that which cor-

responds to the hardness of the water in your area:

0 The dishwasher must be switched off.

Manual setting:

1. Open the dishwasher door.

2. Remove the lower rack from the

dishwasher.

3. Turn the hardness range switch to 0

or 1 (see table).

4. Replace the lower rack.

Electronic setting:

1. Press the ON/OFF button.

The LED in the ON/OFF button will become illuminated.

If other indicators are also illuminated, this means that a dishwashing

cycle has been activated. The dishwashing cycle must be cancelled

(RESET):

Press function buttons 1 and 2 simultaneously for approx. 2 seconds.

All other indicators will go out.

2. Press the function buttons 1 and 2 simultaneously and keep them

pressed.

The LED indicators in function buttons 1 to 3 will flash.

3. Press function button 1again.

The LED indicator for function button 1 will flash.

The multi-display will indicate the hardness setting.

4. Pressing function button 1 increases the hardness setting by 1 degree.

(Exception: hardness setting 1 follows hardness setting 10).

5. When the hardness setting is correct, press the ON/OFF button.

The hardness setting is now saved.

1) (°d) German degree, measure of the hardness of water

2) [mmol/l] millimol per litre, international unit for the hardness of water

3) On this setting the length of the dishwashing cycle may be slightly longer.

*) Factory setting

Operating Instructions

Special salt for the water softener

If the water hardness in your area is less than 4 °d, then the water in

your dishwasher does not need to be softened and you do not need to

use special salt or salt substitute.

Water can be softened in one of two ways:

• If you are using dishwasher detergent that already contains salt sub-

stitute, the detergent only is put into the detergent compartment.

– In this case the water softener must manually be set to 0 and

electronically to 1 to ensure that no special salt is added.

• If you are using dishwasher detergent and special salt separately, the

special salt is to be put into the salt supply container.

– In this case the water softener must manually be set to 0 and

electronically to between 2 and 10 (depending on the water

hardness in your area) to ensure that the special salt is taken from

the detergent container only.

Use only special salt intended for dishwashers. Never fill the salt supply

container with different types of salt (e.g. cooking salt) or detergent.

This would destroy the water softener.

Prior to filling with salt, please check each time that you really do have

a packet of special salt in your hand.

Setting the amount of special salt to be added

Some appliances are equipped with an additional 3in1 function.

If you use 3-in-1 dishwashing tablets and select the 3in1 function

together with the dishwashing cycle, the inflow of special salt does not

have to be deactivated (see ”3in1 function”).

0 1. Set the water softener manually and electronically to the desired water

hardness:

Manual

setting

Electronic

setting

Multi-display

indicator

Addition of special salt

0 1

Do not add special salt.

0 - 1 2-10

2 l to 10l

Addition of special salt

via salt supply container

(factory setting)

Operating Instructions

If the water softener is electronically set at “1” for the purpose of using

detergent that includes special salt, the special salt indicator is deacti-

vated.

Adding special salt

If you are using dishwasher detergent and special salt separately, add

the special salt:

– Before using the dishwasher for the first time.

– When the indicator for special salt

J is illuminated on the control

panel.

0 1. Open the door, remove the lower

rack.

2. Undo the lid on the salt container by

turning it anticlockwise.

3. Only when using for the first time:

fill the salt container with water.

4. Place the funnel supplied on the con-

tainer opening.

Fill the container with special salt

through the funnel; the capacity of

the container is approx. 1.0-1.5 kg

depending on the grain size. Do not

overfill the salt container with special salt.

The water expelled by filling the salt container with special salt runs

out of the salt container onto the base of the washing compartment.

This is not a cause for concern, the water will be pumped out at the

start of the next wash programme.

5. Clean any salt remnants on the container opening.

6. Turn the lid clockwise to the stop, otherwise special salt will leak into

the wash water, this could lead to poor wash results. To avoid this run a

rinse programme after filling the salt container with special salt. This

will wash away salt water and any salt crystals that have been spilt.

Depending on the size of the salt grains, it can take several hours for

the salt to dissolve in the water and the special salt indicator

J to

extinguish. The setting of the water softener and thus the consumption

of salt are dependent on the hardness of the local water.

SALE

SALT

SALZ

SEL

Operating Instructions

Filling with Rinse Aid

Rinse aid ensures that your dishes gleam and are free from spots, and

that you glasses are clear.

Use only branded rinse aid for dishwashers. Never fill the rinse aid con-

tainer with any another substance (e.g. concentrated vinegar). This

would damage the appliance.

Fill with rinse aid:

– Prior to using the dishwasher for the first time

– When the RINSE AID indicator

H on the control panel is illuminated.

The rinse aid compartment is on the inside of the dishwasher door.

0 1. Open the door.

2. Press the rinse aid compartment

release button with your finger.

3. Fully open the rinse aid compartment

lid.

4. Fill with rinse aid exactly up to the

level marked “max”; this corresponds

to a quantity of approx. 140 ml.

5. Close the lid and press until it locks

into place.

6. Wipe up any spilt rinse aid with a

cloth. Otherwise too much foam will

be formed during the wash.

Operating Instructions

Adjusting Rinse Aid Dosing

As the dishes are washed rinse aid is released from the dispenser into

the wash water. The dose is factory set at 4, and can be adjusted from

1 to 6. Only change the setting if streaks, milky spots or dried on water

marks are visible on glasses or crockery.

0 1. Open the door of the dishwasher.

2. Press the rinse aid compartment

release button with your finger.

3. Fully open the rinse aid compartment

lid.

4. Set the dose level.

5. Close the lid and press until it locks

into place.

6. If rinse aid has run out, wipe up with

a cloth.

Operating Instructions

In Daily Use

• Is it necessary to refill with special salt or rinse aid?

• Load cutlery and dishes into the dishwasher

• Fill with dishwasher detergent

• Select a wash programme suitable for the cutlery and dishes

• Start the wash programme

Loading cutlery and dishes

Sponges, household cloths and any object that can absorb water may

not be washed in the dishwasher

• Before loading the dishes, you should:

– Remove large left-overs.

– Soften remnants of burnt food in pans.

• When loading the dishes and cutlery, please note:

– Dishes and cutlery must not impede the rotation of the spray arms.

– Load hollow items such as cups, glasses, pans, etc. with the opening

downwards so that water cannot collect in the container or a deep

base.

– Dishes and items of cutlery must not lie inside one another, or

cover each other

For washing in the dishwasher the following cutlery/dishes

are not suitable: are of limited suitability:

• Cutlery with wooden, horn,

china or mother of pearl handles

• Plastic items that are not heat

resistant

• Older cutlery with cement that is

not temperature resistant

• Bonded cutlery items or dishes

• Pewter or copper items

• Lead crystal glass

• Steel items subject to rusting

• Wooden platters

• Items made from synthetic fibres

• Only wash stoneware in the dishwasher if it

is specifically marked as being dishwasher-

safe by the manufacturer.

• Glazed patterns may fade if machine

washed frequently.

• Silver and aluminium parts have a tendency

to discolour during washing. Left-overs, e.g.

egg white, egg yolk and mustard often

cause discolouring and staining on silver.

Therefore always clean left-overs from silver

immediately, if it is not to be washed

straight after use.

• Some types of glass can become dull after a

large number of washes.

Operating Instructions

– To avoid damage to glasses, they must not touch

– Do not lay small objects (e.g. lids) in the cutlery rack

Loading Cutlery

Long, pointed items of cutlery in the

cutlery rack are a hazard, particularly

to children (see Safety Instructions).

To ensure that all items of cutlery are

completely washed, you should

1. Place the grid insert on the cutlery

rack

2. Place short knives, forks and spoons

in the grid insert with their handles

pointing downwards.

To make the removal of cutlery easier, on some dishwasher models it

is possible to open the cutlery rack.

If you use the grid insert then the

cutlery rack cannot be opened.

To ensure that the cutlery rack can-

not open on removal from the appli-

ance, you should always hold both

parts of the two part handle.

0 1. Place the cutlery rack on a table or

work surface

2. Open the two part handle

3. Remove cutlery

4. Close the two part handle.

Operating Instructions

Loading Pans, Frying Pans

and Large Plates

Load large and heavily soiled dishes

in the lower rack (Plates up to 29cm

in diameter).

Your dishwasher has one of the following four types of lower rack:

Type 1: None of the plate inserts in the lower rack can be removed

Type 2: The right-hand plate inserts in the lower rack can be

folded over to the left

To ease the loading of large items,

the two right-hand plate inserts in

the lower rack can be folded over to

the left:

0 1. Slightly lift the right plate insert.

2. Fold the plate insert to the left.

Operating Instructions

Type 3: The right-hand plate inserts in the lower rack can be

folded across one another

To ease the loading of large items,

the two right-hand plate inserts in

the lower rack can be folded across

one another.

Type 4: The two rear plate inserts in the lower rack can be folded

across one another

To ease the loading of large items,

the two rear plate inserts in the lower

rack can be folded across one

another.

Operating Instructions

Loading Cups, Glasses and

Coffee Services

Load small, delicate items and long

pointed cutlery in the upper rack.

• Arrange items of crockery on the

folding cups racks so that they are

offset from each other and water

can reach all items.

• The cup racks can be folded up out

of the way for tall items.

• Lay or hang wine, champagne, and

brandy glasses in the cut outs on

the cup racks.

• Glasses, beakers, etc. can also be

placed on the two rows of prongs

on the left of the upper rack.

Operating Instructions

Adjusting the Height of the Upper Basket

The height of the basket can also be adjusted when it is loaded.

Lowering the Upper Basket:

0 1. Pull the upper basket out completely.

2. Holding the upper basket at the rear

right, lift it as far as it will go and

then lower it vertically. The upper

basket will engage in the lower posi-

tion.

Raising the Upper Basket:

0 1. Pull the upper basket out completely.

2. Holding the upper basket at the rear

right, lift it as far as it will go and

then lower it vertically. The upper

basket will engage in the higher

position.

Maximum Height of the Dishes in the

Upper Basket Lower Basketk

With upper basket raised 22 cm 31 cm

With upper basket lowered 24 cm 29 cm

Operating Instructions

Filling with Detergent

Only use dishwasher detergent.

Fill with detergent:

– Prior to the start of a wash programme (not for the pre wash pro-

gramme). The detergent is released into the wash water during the

programme.

Please observe the manufacturer's dosing and storage recommenda-

tions as stated on the detergent packaging.

The detergent compartment is on the

inside of the dishwasher door.

0 1. If the lid is closed:

press release button (1).

The lid springs open.

2. Fill the detergent dispenser with

detergent. The markings indicate the

dosing levels:

“20” corresponds to approx. 20 ml of

detergent,

“30” corresponds to approx. 30 ml of

detergent.

3. Close the lid and press until it locks

into place.

If the dishes are very heavily soiled

put additional detergent into the

adjacent chamber (2). This detergent

will take effect during the pre wash.

Operating Instructions

Use of "3 in 1"/ Combi Detergent Tablets

General Advice

These products are tablets with combined detergent/rinse-aid and salt

functions.

0 1. Before using these products you should first check that the water hard-

ness in your supply is compatible with the use of these products as per

the detergent manufacturers instructions (on the product packaging).

2. These products should be strictly used according to the detergent man-

ufacturers instructions.

Do not place the tablets in the tub or the cutlery basket as this will

result in poorer wash results. The tablets should be placed in the

detergent doser.

3. If you encounter problems when using "3 in1" products for the first

time then please contact the detergent manufacturers care line (the

telephone number is given on the product packaging).

Special Advice

When using combination products, the rinse-aid and salt lights are no

longer useful. It may be helpful therefore to switch the rinse aid off -

please note that only some dishwashers have this facility - and select-

ing the lowest possible setting for water hardness.

For more information please refer to your instruction manual.

If you decide to switch to the use of a standard detergent system we

advise that you:

• Refill both the salt and rinse aid compartments.

• Switch the waterhardness setting to the highest possible position

and run for three normal cycles without a load.

• Readjust the waterhardness setting again according to the conditions

for your region (as per the instruction manual).

Operating Instructions

Concentrated Detergent

Based on their chemical composition, dishwasher detergents can be

split into two basic types:

– conventional, alkaline detergents with caustic components

–low alkaline concentrated detergents with natural enzymes.

The use of 50 °C wash programmes in conjunction with concentrated

detergents reduces pollution and is good for your dishes; these wash

programmes are specially matched to the dirt-dissolving properties of

the enzymes in the concentrated detergent. For this reason 50 °C wash

programmes in which concentrated detergents are used can achieve

the same results that can otherwise only be achieved using 65 °C pro-

grammes.

Detergent tablets

Detergent tablets of different makes dissolve at different speeds. For

this reason some detergent tablets cannot develop their full cleaning

power during short programmes. Therefore please use wash pro-

grammes with pre wash when using detergent tablets.

Operating Instructions

Selecting the Wash Programme (Programme Table)

Choose the most suitable wash programme with the aid of this table:

During BIO programmes the water is briefly heated to more than 50 °C so that the active oxygen

becomes effective.

The various stages in the wash programme have different sounds because the dishes are washed

more intensely for short periods during certain stages of the wash programme to improve cleaning.

The consumption figures were recorded under standard conditions. They are dependent on the load-

ing of the dish racks. Variations are therefore possible in practice.

Testprogramme for Test Institutes.

When the hardness setting is electronically adjusted to 10, the length of the dishwashing cycle may

be slightly longer.

Type of

Dishes

Dinner Service and Cooking Utensils

Dessert Dishes

and Coffee

Service

All Dish Types

In Addition

- -

with non-tem-

perature resist-

ant dishes

with

delicate glasses

Type of

Soiling

•heavily

soiled

• dried on left-

overs, partic-

ularly egg

white and

thickeners

•normally

soiled

• dried left-

overs

•normally

soiled

• lightly

soiled

Used dishes

that are being

collected in the

dishwasher for

washing later.

particularly suited to the use of

concentrated detergents.

Suitable

Programme:

    

INTENSIVE

70 °C

NORMAL

65 °C

NORMAL BIO

50 °C

1) 4)

QUICK 50 °C

PRE WASH

Programme

Sequence

Pre Wash

Main Wash

2x Intermedi-

ate Rinses

Final Rinse

Drying

Pre Wash

Main Wash

Intermediate

Rinse

Final Rinse

Drying

Pre Wash

Main Wash

Intermediate

Rinse

Final Rinse

Drying

Main Wash

Intermediate

Rinse

Final Rinse

Pre Wash

Consump-

tion

Figures:

    

Duration

110 – 120 min. 90 – 100 min. 120 - 130 min. 39 min. 12 min.

Energy

1.75 – 1.95 kWh 1.15 – 1.35 kWh 0.95 - 1.05 kWh 0.8 kWh < 0.1 kWh

Water

19 – 21 litres 16 – 18 litres 13 – 15 litres 12 litres 4litres

Operating Instructions

Starting a dishwashing cycle

0 1. Check that the dishes and cutlery are stacked in the dishwasher in such

a way that the spray arms are free to rotate.

2. Turn on the tap fully.

3. Close the door.

4. Press the ON/OFF button.

The LED in the ON/OFF button will become illuminated.

5. Press the relevant button for the cycle required (see “Cycle Table”).

The cycle display will become illuminated. The remaining time for the

cycle will be shown in the multi-display.

The selected cycle will begin after approximately 3 seconds.

During the dishwashing cycle, the remaining time shown in the multi-

display may be adjusted according to amount of dishes, degree of soil-

ing, etc.

If an error message is displayed in the multi-display after the cycle has

begun, please read the section “What to do if ...”.

Changing/interrupting/aborting a dishwashing cycle

Only change or interrupt a dishwashing cycle that is in progress if it is

absolutely necessary. After the appliance has been closed again, the air

that has entered will be heated significantly and expand. As a result,

water may collect in the base of the appliance and trigger the anti-

flood system.

Changing a dishwashing cycle

If you would like to change the dishwashing cycle in the first 3 seconds

after having selected a cycle, briefly press the button for the new dish-

washing cycle.

If you would like to change the dishwashing cycle after this time, pro-

ceed as follows:

0 1. Press the button for the new dishwashing cycle and hold it down.

The indicator for the dishwashing cycle that is currently running will

flash.

After several seconds only the indicator for the new dishwashing cycle

will be flashing.

2. Release the cycle button.

The newly selected dishwashing cycle will begin.

Operating Instructions

Interrupting the dishwashing cycle by opening the dishwasher door

Hot steam may escape when the door is opened. There is a risk of scald-

ing. Open the door carefully.

0 1. Open the door of the dishwasher.

The dishwashing cycle will stop.

2. Close the door.

The dishwashing cycle will continue.

Aborting the dishwashing cycle (RESET)

0 1. Press the function buttons 1 and 2 simultaneously and keep them

pressed.

The cycle display for the current cycle will flash for several seconds and

then cease to be illuminated.

2. Release the function buttons.

The dishwashing cycle has been aborted.

Turning off the dishwasher will only interrupt a selected dishwashing

cycle, not abort it. The dishwashing cycle will recommence after turn-

ing the dishwasher back on again.

Setting or changing the start delay

Using the start delay timer you can adjust when within the next 19

hours the dishwashing cycle is to begin.

Setting the start delay:

0 1. Press the ON/OFF button.

2. Continue pressing the DELAY TIMER button b until the number of

hours’ delay until the dishwashing cycle is to start is flashing in the

multi-display.

3. Press the button for the desired dishwashing cycle.

The length of the selected dishwashing cycle will flash for a moment in

the multi-display, and then it will display the selected starting time

again.

As soon as the number of hours is displayed without flashing, the start

delay has been activated.

The dishwashing cycle will start automatically following a countdown

of the hours set.

Changing the start delay:

As long as the dishwashing cycle has not started, you can still change

the start delay set by pressing the DELAY TIMER button.

Operating Instructions

Cancelling the start delay:

As long as the dishwashing cycle has not begun you are able to cancel

the start delay. Continue pressing the START DELAY button until the

length of the selected dishwashing cycle appears in the multi-display.

The selected dishwashing cycle will begin immediately.

Changing the dishwashing cycle after the start delay has been set:

As long as the dishwashing cycle has not started, you can still change

the start delay set by pressing a cycle button.

0 1. Press the button for the new dishwashing cycle and hold it down.

First the indicator for the dishwashing cycle that has just been selected

will flash.

After several seconds only the indicator for the new dishwashing cycle

will be flashing.

2. Release the cycle button.

The newly selected dishwashing cycle will start automatically following

a countdown of the hours set.

Load Sensing – Sensor Logic

If a wash programme is started even though there are only a few dishes

in the upper and/or lower rack, an intelligent electronic system adjusts

the amount of water and the duration of the wash programme to the

number of dishes. By this means it is possible to wash only a few dishes

quickly and economically. At half load (6 place settings), up to 2 litres

of water and 0.2 kWh of electricity are saved.

Operating Instructions

Switching Off the Dishwasher

Only switch the dishwasher off when the multi-display indicates "0"

remaining programme time.

0 1. Press the ON/OFF button.

The ON/OFF button indicator extinguishes.

Hot steam may escape from the appliance when opening the door

immediately after the end of the programme. Therefore:

2. Open the door carefully.

Emptying the Dishwasher

• Hot dishes are sensitive to knocks. The dishes should therefore be

allowed to cool down before removing them from the appliance.

• Leave the dishes in the dishwasher for approx. 15 minutes after the

end of the programme so that they dry better and can cool down.

• First empty the lower rack, and then the upper rack. By using this

procedure you will avoid any water that may be remaining in the

upper rack, dripping onto the dishes in the lower rack and leaving

water marks.

Care and Cleaning

Do not under any circumstances use furniture care products or aggres-

sive cleaners.

• If necessary, clean the controls only with a soft cloth and pure warm

water.

• Occasionally check the internal containers, door seal, and water inlet

for soiling, clean if necessary.

Operating Instructions

Cleaning the Filter

The filters in the base of the washing compartment are to a large

extent self-cleaning.

Nevertheless the filters should be

checked and cleaned from time to

time. Dirty filters will degrade the

washing result.

0 1. Open the door, remove the lower

rack.

2. The dishwasher filter system com-

prises a coarse/fine filter, microfilter

and a flat filter. Unlock the filter sys-

tem using the handle on the microfil-

ter, and remove.

3. Turn the handle about ¼ a turn anti-

clockwise and remove.

4. Take hold of the coarse/fine filter (1)

by the handle with the hole and

remove from the microfilter (2)

5. Clean all filters thoroughly under

running water.

6. Remove the flat filter (3) from the

base of the washing compartment

and clean both faces thoroughly

7. Put the flat filter back in the base of

the washing compartment

8. Place the coarse/fine filter in the

microfilter and press together.

9. Put the filter combination in place

and lock by turning the handle clock-

wise to the stop. During this process

ensure that the flat filter does not

protrude above the base of the wash-

ing compartment.

Under no circumstances may the

dishwasher be used without filters.

Operating Instructions

What to do, when ...

Try to rectify minor faults on the dishwasher with the aid of the

instructions given here. If you call in customer service to resolve one of

the malfunctions listed here, or rectify an error made in the operation

of the appliance, the customer service engineer’s visit is not free of

charge, even during the period of guarantee.

...Error messages are displayed.

If any of the indicators in the control panel, as listed in the table below,

are flashing or are illuminated, you can probably rectify the fault your-

self.

Malfunction Possible cause Remedy

The cycle indicator for the

selected dishwashing cycle

is flashing: error code

Å10

is displayed in the multi-dis-

play: There is no water run-

ning into the dishwasher.

The tap is blocked or furred

with lime-scale

Clean tap

The tap is turned off. Turn the tap on.

The filter (where present) in

the threaded hose fitting at

the water inlet valve is

blocked.

Clean the filter in the

threaded hose fitting.

Filters in the base of the

washing compartment are

blocked.

Press the button for the

commenced dishwash-

ing cycle; then abort the

dishwashing cycle by

pressing RESET (see

chapter: “Starting a

dishwashing cycle”);

clean out the filters (see

chapter: “Cleaning the

filters”).

The water inlet hose has not

been correctly laid.

Check hose installation.

Operating Instructions

After rectifying an Å10 or Å20 error, press the button for the dish-

washing cycle that has been started. The dishwashing cycle will con-

tinue.

If the fault is displayed again, please contact customer service.

For all other errors displayed, please contact customer service, stating

the error code. (See chapter “Customer Service”).

The cycle indicator for the

selected dishwashing cycle

is flashing, error code

Å20

is displayed in the multi-dis-

play:

The siphon is blocked. Clean out siphon.

The water drain hose has

not been correctly laid.

Check hose installation.

Error code Å30 is displayed

in the multi-display:

The leak prevention system

has been triggered.

Turn off the tap and

contact customer serv-

ice.

Malfunction Possible cause Remedy

Operating Instructions

...problems occur during use of the dishwasher.

...the wash results are not satisfactory.

The dishes are still dirty.

– The wrong wash programme was selected.

– The dishes were loaded is such a way that the wash waster did not

reach all items. The racks for the dishes must not be overloaded.

– The filter in the base of the washing compartment is dirty or incor-

rectly positioned.

– Detergent was not used or too little was used.

– In the case of scale deposits on the dishes: The special salt container

is empty or the water softener is incorrectly adjusted.

– The drain hose is incorrectly laid.

The dishes are wet and dull.

– Rinse aid was not used.

– The rinse aid container is empty.

Malfunction Possible Cause Remedy

The programme does

not start.

The door of the dishwasher is

not closed properly.

Shut the door.

Mains plug is not plugged in. Insert mains plug.

House fuse is defective. Replace fuse.

In the case of dishwasher

models with start delay

timer:

A start delay is selected.

If dishes are to be washed

immediately cancel delay

start timer.

Rust spots are visible in

the washing compart-

ment.

The washing compartment is

made from rust-free stainless

steel. Rust spots in the wash-

ing compartment are due to

rust particles from external

sources (rust particles from

water pipes, pans, cutlery,

etc.). Remove such spots with

one of the stainless steel

cleaners that are generally

available on the market.

Only wash cutlery and dishes

that are suitable for dish-

washer use.

Close the lid of the special

salt container securely.

There is a whistling

noise during washing.

The whistling is not a cause

for concern.

Use a different brand of

detergent.

Operating Instructions

There are streaks, milky spots or a bluish coating on glasses and

dishes.

– Lower rinse aid dosing.

There are dried water drops on the glasses and dishes.

– Increase rinse aid dosing.

– The detergent may be the cause. Contact the detergent manufac-

turer’s customer advisor.

Technical Data

; This appliance conforms with the following EU Directives:

– 73/23/EWG dated 19. 02. 1973 – Low Voltage Directive

– 89/336/EWG dated 03. 05. 1989

(including Directive Amendment 92/31/EWG) – EMC Directive

Capacity: 12 place settings including serving dishes

Permitted Water

Pressure:

1-10 bar (=10-100 N/cm

= 0.1-1.0 MPa)

Electrical Connection:

Information on the electrical connection is given on the

rating plate on the inner edge of the dishwasher door on

the right.

Dishwasher: Free-Standing Appliances

Dimensions: 850 x 600 x 600 (H x W x D in mm)

Max. Weight: 54 Kg

Dishwashers that Can Be Integrated, Built-In Dishwashers

Dimensions: 820 – 880 x 596 x 570 (H x W x D in mm)

Max. Weight: 50 Kg

Dishwashers that Can Be Fully Integrated

Dimensions: 820 – 880 x 596 x 546 - 550 (H x W x D in mm)

Max. Weight: 50 Kg

Operating Instructions

Notes for Test Institutes

Testing in accordance with EN 60704 must be carried out with the

appliance fully loaded and using the test programme (see Programme

Table).

Tests in accordance with EN 50242 must be carried out when the salt

dispenser and rinse aid container have been filled with salt and rinse

aid respectively and using the test programme (see Programme Table).

Sample loading arrangements:

Upper basket *

* If necessary, move the cup rest from right to left. When doing this, ensure that the

cup rest is at the same height.

Lower basket with cutlery basket Cutlery basket

Full Load:

12 place settings

incl. serving dishes

Half Load:

6 place settings incl. serving, leaving

alternate positions free

Detergent Dosing: 5g + 25g (Type B) 20g (Type B)

Rinse Aid Setting: 4 (Type III) 4 (Type III)

Installation and Connection Instructions

INSTALLATION AND CONNECTION

INSTRUCTIONS

Installing the Dishwasher

• The dishwasher must be installed on a firm floor and adjusted to

ensure that it is stable and level.

• To compensate for unevenness in the

floor and to match the height of the

appliance to that of surrounding units

extend the threaded feet by unscrew-

ing:

– use a screwdriver.

• For built-in, integrated and fully integrated dishwashers, the rear feet

should be adjusted from the front of the appliance using a screwdriver.

• The drain hose, inlet hose and mains cable must not be kinked or

crushed when the dishwasher is in position.

• The dishwasher must also be screwed on tightly to the work surface

or to the adjoining units. This is essential to ensure the dishwasher

does not tip.

Installation and Connection Instructions

Dishwashers That Can Be Integrated

(see installation template supplied)

The door of the appliance can be fitted with a wooden furniture door

with the following dimensions:

Width: 591 – 594 mm

Thickness: 16 – 24 mm

Height:

(variable)

dependent on

– Recess height

– Plinth height

– The adjustment so that the unit matches the height of

the adjoining units

The exact height of the adjoining units must be

measured at the place of installation.

Weight: max. 8 kg

Installation and Connection Instructions

Connecting the Dishwasher

Water Connection

The dishwasher is fitted with safety devices that prevent the wash

water returning into the drinking water system and comply with the

applicable plumbing regulations.

• The dishwasher can be connected to cold and hot water supplies up

to max. 60 °C.

•The dishwasher must not be connected to open hot water appliances

or instantaneous water heaters.

Permitted water pressure

Connect the inlet hose

The water inlet hose must not be kinked, crushed or entangled when it

is being connected up.

0 Connect the threaded hose fitting (ISO 228-1:2000) on the water inlet

hose to a tap with an external thread (¾ inch). The inlet hose is

equipped either with a plastic or with a metal connection nut:

– Tighten plastic hose connection nuts by hand only.

– Metal hose connection nuts must be tightened using an

appropriate tool. Finally, visually check that it is water-tight (ensure

that the tap is not dripping).

• In order that access to the tap in the kitchen is not limited by the use

of the dishwasher, we recommend the installation of an additional

tap, or fitting a two way adapter to the existing tap.

• If you need a longer water inlet hose than that supplied, VDE

approved complete hose sets are to be used. These are available from

your local Service Force Centre.

Lowest permitted water pressure:

1 bar (=10 N/cm

=100 kPa)

Consult your installer if the water pres-

sure is less than 1 bar.

Highest permitted water pressure:

10 bar (=100 N/cm

=1 MPa)

In the case of a water pressure greater

than 10 bar, a pressure reduction valve

must be used (available from your

dealer).

Installation and Connection Instructions

The following section is only applicable to dishwashers that have a

safety valve on the threaded hose fitting for the tap:

Water inlet hose with safety valve

After connecting the double-walled water inlet hose, the safety valve is

next to the tap. Therefore the water inlet hose is only under pressure

while the water is running. If the water inlet hose starts to leak during

this operation, the safety valve cuts off the running water and the

draining pump in the dishwasher is switched on.

Please take care when installing the water inlet hose:

– The distance between the bottom

edge of the safety value and the

floor on which the dishwasher is

standing must be at least 30 cm:

– The electrical cable for the safety

valve is in the double-walled water

inlet hose. Do not immerse the

water inlet hose or the safety valve

in water.

– If the water inlet hose or the safety

valve is damaged, remove the

mains plug immediately.

– A water inlet hose with safety valve

must only be replaced by a

specialist or Customer Services.

– Place the water inlet hose in such a way that it is never higher than

the bottom edge of the safety valve.

Installation and Connection Instructions

Water drain

Drain hose

The drain hose must not be kinked, crushed or entangled.

• Connecting the drain hose:

– Maximum permitted height: 1 metre.

– Minimum required height 40 cm above the lower edge of the

machine.

Extension hoses

• Extension hoses are available from

your dealer or customer service.

The internal diameter of the exten-

sion hoses must be 19 mm to

ensure that the function of the

appliance is not impeded.

• Extension hoses may be laid a max-

imum of 3 metres horizontally; the

maximum permitted height for the

connection for the drain hose is

then 85 cm.

Sink outlet connection

• The outlet of the drain hose (ø 19 mm) fits all commonly available

sink outlet spigot types. The outer diameter of the spigot connection

must be at least 15 mm.

• The drain hose must be fixed to the sink outlet connection using the

hose clamp supplied.

If the dishwasher is fitted at a high position

If the dishwasher is installed at a high level, and the drainhose connec-

tion is less than 30 cm from the bottom of the appliance, adapter kit

ET 111099520 must be fitted. This is available from Customer Service.

Water drain into wash basins (only possible with free-standing

appliances)

In the case that you wish to hang the drain hose in a wash basin, use a

detachable hose elbow. You can obtain this from AEG customer service

under spare part number ET 646 069 190.

0 1. Fit the elbow to the drain hose.

2. Secure the drain hose against sliding off the edge of the wash basin.

Pass a piece of cord through the hose elbow and fix it to the wall or the

tap.

Installation and Connection Instructions

Leak Prevention System

For protection from damage due to water leaks, the dishwasher is

equipped with a leak prevention system, the AQUA CONTROL SYSTEM.

In the event of a fault, the safety valve in the appliance immediately

interrupts the inflow of water and the drain pump is activated. By this

means water can neither escape nor overflow. The remaining water in

the appliance is automatically pumped out.

The leak prevention system also works when the appliance is switched

off.

Electrical connection

In compliance with electric company technical requirements for mains

connections, hard-wired connections to the mains may only be made

by approved electri-cians.

When connecting the appliance, observe the German VDE regulations

and, if applicable, any additional conditions required by your local elec-

tricity supplier. Following installation, live parts and live insulated wir-

ing must not be accessible using a finger test in accordance with EN

60335/DIN VDE 0700.

Information on the electrical connection can be found on the rating

plate on the right side of the inner edge of the dishwasher door. If the

appliance has a change-over switch, the additional instructions on the

change-over diagram in the mains connector box must be observed.

Prior to connecting ensure that the mains voltage and current rating at

the site of installation match the nominal voltage and current rating

given on the rating plate. The required fuse protection is also to be

found on the rating plate.

To isolate the dishwasher from the mains, remove the mains plug.

Important: The plug must still be accessible after the appliance has

been installed.

If the appliance is hard-wired to the mains supply, then it must be

safely isolated from the mains within the electrical installation with

switches intended to ensure all-pole(N,L1) disconnection, shall be

directly connected to the supply terminals and shall have a contact

separation (fuses, cut outs, current trips or similar) of at least 3mm in

each pole.

Installation and Connection Instructions

Connections

The water inlet and drain hoses, as well as the mains cable must be

connected beside the dishwasher as there is insufficient space behind

the appliance.

The plumbing and electrical installation example given below can only

be regarded as a recommendation; the actual situation where the dish-

washer is to be installed will define the exact installation (available

connections, local electricity and water board regulations for connect-

ing up appliances, etc.).

Two 45° or Straight Connections,

Outer ø 19 mm, Length 30 mm

Double tap Water drain Water inlet

Water

drain

Water

inlet

Mains

cable

Mains

cable

Mains socket

Service Departments

SERVICE DEPARTMENTS

Belgium

Tel.: Fax.:

Electrolux Home Products Belgium

ELECTROLUX SERVICE

Bergensesteenweg 719

1502 Lembeek

Consumer services 02/363.04.44 02/363.04.00

02/363.04.60

Province de Liège:

S.D.E.

Rue Gaucet 26

4020 Liege

04/343.11.60 04/343.47.68

Guarantee Conditions

GUARANTEE CONDITIONS

WAARBORGVOORWAARDEN

Onze toestellen worden met de grootst mogelijke zorgvuldigheid geproduceerd. Deson-

danks kan het voorkomen dat er een defect optreedt. Onze klantendienst zal dit op ver-

zoek herstellen, zowel binnen als buiten de waarborgtermijn. De levensduur van het

toestel wordt daardoor niet negatief beïnvloed.

Onderstaande waarborgvoorwaarden zijn gestoeld op de EU Richtlijn 99/44/EG en het

Burgerlijk Wetboek. De daaruit voortvloeiende rechten blijven onverlet.

Ook de waarborgverplichtingen van de verkoper naar de eindgebruiker blijven onaang-

etast.

Voor dit toestel verlenen wij waarborg volgens onderstaande voorwaarden:

1. Wij verhelpen kosteloos met inachtneming van de voorwaarden 2 tot en met 15

gebreken aan het toestel die zich openbaren binnen 24 maanden vanaf de datum van

levering aan de eindgebruiker. Deze waarborgvoorwaarden zijn niet van toepassing in

geval van professioneel of daarmee gelijk te stellen gebruik.

2. De waarborgprestatie houdt in dat het toestel kosteloos wordt teruggebracht in de toe-

stand die het had voor het defect optrad. Gebrekkige onderdelen worden hersteld of

vervangen. Kosteloos vervangen onderdelen worden ons eigendom.

3. Het gebrek moet terstond gemeld worden, om mogelijke verdere schade te voorkomen.

4. Voor een beroep op waarborg dient het aankoopbewijs met aankoop- en/of leverings-

datum te worden overlegd.

5. De waarborg heeft geen betrekking op schade aan kwetsbare onderdelen, zoals (vit-

rokeramisch) glas, kunststof, rubber, die ontstaan is door onzorgvuldig gebruik

6. De waarborg heeft geen betrekking op kleine afwijkingen van de gestelde kwaliteit die

voor de waarde en deugdelijkheid van het toestel onbeduidend zijn.

7. De waarborg geldt evenmin voor schade veroorzaakt door:

• chemische en elektrochemische inwerking van water,

• abnormale milieuomstandigheden in het algemeen

• voor het toestel oneigenlijke bedrijfsomstandigheden

• contact met agressieve stoffen.

8. De waarborg heeft geen betrekking op gebreken door transportschade die buiten onze

verantwoordelijkheid is ontstaan, niet vakkundige installatie of montage, verkeerd

gebruik, gebrekkig onderhoud, of het niet in acht nemen van de gebruiks- of mon-

tageaanwijzingen.

9. Het recht op waarborg vervalt wanneer het defect werd veroorzaakt door herstelling of

ingrepen door derden die niet bevoegd of niet deskundig zijn, of wanneer het toestel

voorzien werd van toebehoren of onderdelen die niet origineel zijn en daardoor een

defect veroorzaken.

10. Toestellen die gemakkelijk kunnen worden vervoerd dienen te worden overhandigd of

gezonden naar onze klantendienst. Herstelling ter plaatse kan slechts worden gevraagd

voor grote of ingebouwde toestellen.

11. Indien het toestel zodanig is ingebouwd, ondergebouwd, opgehangen of geplaatst dat

de benodigde tijd voor het in- en uitbouwen samen meer dan 30 minuten bedraagt,

dan worden de hierdoor ontstane extra kosten aan de gebruiker in rekening gebracht.

Schade die ontstaat door abnormale in- of uitbouw komt ten laste van de gebruiker.

12. Indien binnen de waarborgperiode de herstelling van hetzelfde gebrek meermaals mis-

lukt of de herstellingkosten disproportioneel zijn wordt in overleg met de gebruiker een

gelijkwaardige vervanging geleverd. In geval van vervanging behouden we ons het

recht voor om een vergoeding te rekenen naar rato van de verstreken gebruiksperiode.

Guarantee Conditions

13. Herstelling onder waarborg heeft geen verlenging van de waarborgtermijn noch aan-

vang van een nieuwe waarborgtermijn tot gevolg.

14. Op herstellingen geven wij een waarborg van 12 maanden, uitsluitend op hetzelfde

gebrek.

15. Verdere of andere rechten, in het bijzonder vergoeding van schade ontstaan buiten het

toestel, zijn uitgesloten voor zover een aansprakelijkheid niet wettelijk is vastgelegd.

In geval van aansprakelijkheid zal een vergoeding de aankoopwaarde van het toestel

niet overtreffen.

Deze waarborgvoorwaarden gelden voor in België gekochte en/of in gebruik zijnde

toestellen. Indien een toestel naar het buitenland wordt gebracht dient de gebruiker

na te gaan of het toestel voldoet aan de technische voorwaarden ( o.a. spanning, fre-

quentie, installatievoorschriften, gassoort, klimaatomstandigheden) in het betreffende

land. Voor in het buitenland aangeschafte toestellen dient de gebruiker zich zelf te

vergewissen van de bepalingen in België. Noodzakelijke of gewenste aanpassingen val-

len niet onder de waarborg, en kunnen niet altijd worden aangebracht.

Ook na afloop van de waarborgtermijn staat onze klantendienst u ter beschikking.

Adres Klantendienst:

ELECTROLUX HOME PRODUCTS BELGIUM

Bergensesteenweg, 719

1502 LEMBEEK

Tel.: 02.363.04.44

Service

SERVICE

In the section "What to do, if..." the most important sources of faults

that you can rectify yourself are summarised.

If, nevertheless, you call in customer service to resolve a problem listed

in these instruction, or because of an error made in operating the

appliance, the customer service engineer’s visit is not free of charge,

even during the warranty period.

If you can not find any information on a specific malfunction in these

operating instructions, please contact customer service.

Please provide customer service the PNC number and the S No. (serial

number), you can find these on the rating plate. The plate is on the

inner edge of the door on the right.

So that you always have these numbers at hand, we recommend you to

make a note of them here:

PNC :...............................................................................................................................

S-No. :.............................................................................................................................

From the Electrolux Group. The world´s No.1 choice.

The Electrolux Group is the world´s largest producer of powered appliances for kitchen, cleaning and outdoor

use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines,

vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in more

than 150 countries around the world.

AEG Hausgeräte GmbH

Postfach 1036

D-90327 Nürnberg

http://www.aeg.hausgeraete.de

822 946 908 -00- 0603

Subject to change without notice

AEG FAV50860I-B Handleiding

Merk: AEG

Model: FAV50860I-B

Categorie: Vaatwassers

Type: Handleiding

Deze handleiding is ook geschikt voor

Download PDF

rapport

in andere talen

English: AEG FAV50860I-B User manual

AEG FAV50860I-B Handleiding

Deze handleiding is ook geschikt voor

AEG FAV50860I-B Handleiding

in andere talen

Gerelateerde artikelen

Andere documenten