Yamaha CVP-205 Handleiding

Merk: Yamaha

Model: CVP-205

Categorie: Digitale piano's

Type: Handleiding

OWNER’S MANUAL

CVP-205/205M/203

SPECIAL MESSAGE SECTION

PRODUCT SAFETY MARKINGS:

Yamaha electronic

products may have either labels similar to the graphics

shown below or molded/stamped facsimiles of these

graphics on the enclosure. The explanation of these

graphics appears on this page. Please observe all cautions

indicated on this page and those indicated in the safety

instruction section.

See bottom of Keyboard enclosure for graphic symbol markings.

The exclamation point within the

equilateral triangle is intended to alert

the user to the presence of important

operating and maintenance (servic-

ing) instructions in the literature

accompanying the product.

The lightning ﬂash with arrowhead

symbol, within the equilateral trian-

gle, is intended to alert the user to the

presence of uninsulated “dangerous

voltage” within the product’s enclo-

sure that may be of sufﬁcient magni-

tude to constitute a risk of electrical

shock.

IMPORTANT NOTICE:

All Yamaha electronic products

are tested and approved by an independent safety testing

laboratory in order that you may be sure that when it is

properly installed and used in its normal and customary

manner, all foreseeable risks have been eliminated. DO

NOT modify this unit or commission others to do so

unless speciﬁcally authorized by Yamaha. Product perfor-

mance and/or safety standards may be diminished.

Claims ﬁled under the expressed warranty may be denied

if the unit is/has been modiﬁed. Implied warranties may

also be affected.

SPECIFICATIONS SUBJECT TO CHANGE:

The

information contained in this manual is believed to be

correct at the time of printing. However, Yamaha reserves

the right to change or modify any of the speciﬁcations

without notice or obligation to update existing units.

ENVIRONMENTAL ISSUES:

Yamaha strives to pro-

duce products that are both user safe and environmentally

friendly. We sincerely believe that our products and the

production methods used to produce them, meet these

goals. In keeping with both the letter and the spirit of the

law, we want you to be aware of the following:

Battery Notice:

This product MAY contain a small non-

rechargable battery which (if applicable) is soldered in

place. The average life span of this type of battery is

approximately ﬁve years. When replacement becomes

necessary, contact a qualiﬁed service representative to

perform the replacement.

Warning:

Do not attempt to recharge, disassemble, or

incinerate this type of battery. Keep all batteries away

from children. Dispose of used batteries promptly and as

regulated by applicable laws. Note: In some areas, the

servicer is required by law to return the defective parts.

However, you do have the option of having the servicer

dispose of these parts for you.

Disposal Notice:

Should this product become damaged

beyond repair, or for some reason its useful life is consid-

ered to be at an end, please observe all local, state, and

federal regulations that relate to the disposal of products

that contain lead, batteries, plastics, etc.

NOTICE:

Service charges incurred due to lack of knowl-

edge relating to how a function or effect works (when the

unit is operating as designed) are not covered by the man-

ufacturer’s warranty, and are therefore the owners respon-

sibility. Please study this manual carefully and consult

your dealer before requesting service.

NAME PLATE LOCATION:

The graphic below indi-

cates the location of the name plate. The model number,

serial number, power requirements, etc., are located on

this plate. You should record the model number, serial

number, and the date of purchase in the spaces provided

below and retain this manual as a permanent record of

your purchase.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CVP-205

Model

Serial No.

Purchase Date

CVP-203

92-469

(bottom)

CVP-205/203

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even

death from electrical shock, short-circuiting, damages, ﬁre or other hazards. These precautions

include, but are not limited to, the following:

•

Only use the voltage speciﬁed as correct for the instrument. The

required voltage is printed on the name plate of the instrument.

•

Check the electric plug periodically and remove any dirt or dust

which may have accumulated on it.

•

Use only the supplied power cord/plug.

•

Do not place the power cord near heat sources such as heaters

or radiators, and do not excessively bend or otherwise damage

the cord, place heavy objects on it, or place it in a position where

anyone could walk on, trip over, or roll anything over it.

•

Do not open the instrument or attempt to disassemble the inter-

nal parts or modify them in any way. The instrument contains no

user-serviceable parts. If it should appear to be malfunctioning,

discontinue use immediately and have it inspected by qualiﬁed

Yamaha service personnel.

•

Do not expose the instrument to rain, use it near water or in

damp or wet conditions, or place containers on it containing liq-

uids which might spill into any openings.

•

Never insert or remove an electric plug with wet hands.

•

Do not put burning items, such as candles, on the unit.

A burning item may fall over and cause a ﬁre.

•

If the power cord or plug becomes frayed or damaged, or if there

is a sudden loss of sound during use of the instrument, or if any

unusual smells or smoke should appear to be caused by it,

immediately turn off the power switch, disconnect the electric

plug from the outlet, and have the instrument inspected by quali-

ﬁed Yamaha service personnel.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or

others, or damage to the instrument or other property. These precautions include, but are not limited

to, the following:

•

When removing the electric plug from the instrument or an outlet,

always hold the plug itself and not the cord. Pulling by the cord

can damage it.

•

Remove the electric plug from the outlet when the instrument is

not to be used for extended periods of time, or during electrical

storms.

•

Do not connect the instrument to an electrical outlet using a mul-

tiple-connector.

Doing so can result in lower sound quality, or possibly cause

overheating in the outlet.

•

Read carefully the attached documentation explaining the

assembly process.

Failure to assemble the instrument in the proper sequence might

result in damage to the instrument or even injury.

•

Do not expose the instrument to excessive dust or vibrations, or

extreme cold or heat (such as in direct sunlight, near a heater, or

in a car during the day) to prevent the possibility of panel disﬁgu-

ration or damage to the internal components.

•

Do not use the instrument in the vicinity of a TV, radio, stereo

equipment, mobile phone, or other electric devices. Otherwise,

the instrument, TV, or radio may generate noise.

•

Do not place the instrument in an unstable position where it

might accidentally fall over.

•

Before moving the instrument, remove all connected cables.

•

Do not place the instrument against a wall (allow at least 3 cm/

one-inch from the wall), since this can cause inadequate air cir-

culation, and possibly result in the instrument overheating.

Power supply/Power cord

Do not open

Water warning

Fire warning

If you notice any abnormality

Power supply/Power cord

Assembly

Location

(1)B-7

1/2

CVP-205/203

•

Before connecting the instrument to other electronic compo-

nents, turn off the power for all components. Before turning the

power on or off for all components, set all volume levels to mini-

mum. Also, be sure to set the volumes of all components at their

minimum levels and gradually raise the volume controls while

playing the instrument to set the desired listening level.

•

When cleaning the instrument, use a soft, dry or slightly damp

cloth. Do not use paint thinners, solvents, cleaning ﬂuids, or

chemical-impregnated wiping cloths.

•

Take care that the key cover does not pinch your ﬁngers, and do

not insert a ﬁnger or hand in any gaps on the key cover or instru-

ment.

•

Never insert or drop paper, metallic, or other objects into the

gaps on the key cover, panel or keyboard. If this happens, turn

off the power immediately and unplug the power cord from the

AC outlet. Then have the instrument inspected by qualiﬁed

Yamaha service personnel.

•

Do not place vinyl, plastic or rubber objects on the instrument,

since this might discolor the panel or keyboard.

•

Do not rest your weight on, or place heavy objects on the instru-

ment, and do not use excessive force on the buttons, switches or

connectors.

•

Do not operate the instrument for a long period of time at a high

or uncomfortable volume level, since this can cause permanent

hearing loss. If you experience any hearing loss or ringing in the

ears, consult a physician.

•

Do not place the bench in an unstable position where it might

accidentally fall over.

•

Do not play carelessly with or stand on the bench. Using it as a

tool or step-ladder or for any other purpose might result in acci-

dent or injury.

•

Only one person should sit on the bench at a time, in order to

prevent the possibility of accident or injury.

•

If the bench screws become loose due to extensive long-term

use, tighten them periodically using the included tool.

Saving and backing up your data

•

Current memory data (see page 40) is lost when you turn off the

power to the instrument. Save the data to a ﬂoppy disk/the User

Drive (see page 40).

Saved data may be lost due to malfunction or incorrect opera-

tion. Save important data to a ﬂoppy disk.

Backing up the ﬂoppy disk

•

To protect against data loss through media damage, we recom-

mend that you save your important data onto two ﬂoppy disks.

Always turn the power off when the instrument is not in use.

Connections

Maintenance

Handling caution

Using the bench (If included)

Saving data

When you change settings in a display page and then exit

from that page, System Setup data (listed in the Parameter

Chart of the separate Data List booklet) is automatically

stored. However, this edited data is lost if you turn off the

power without properly exiting from the relevant display.

Yamaha cannot be held responsible for damage caused by improper use or modiﬁcations to the instrument, or data that is lost or destroyed.

(1)B-7

2/2

CVP-205/203

Thank you for purchasing the Yamaha Clavinova!

We recommend that you read this manual carefully

so that you can fully take advantage of the advanced

and convenient functions of the Clavinova.

We also recommend that you keep this manual

in a safe and handy place for future reference.

About this Owner’s Manual and Data List

This manual consists of four main sections: Introduction, Quick Guide, Basic Operation, and Reference.

Also, a separate Data List is provided.

Introduction (page 2):

Please read this section ﬁrst.

Quick Guide (page 20):

This section explains how to use the basic functions.

Basic Operation (page 39):

This section explains how to use the basic operations including display-based controls.

Reference (page 53):

This section explains how to make detailed settings for the Clavinova’s various functions.

Data List :

Voice List, MIDI Data Format, etc.

* The models CVP-205/205M/203 will be referred to as the CVP/Clavinova in this Owner’s Manual.

* The illustrations and LCD screens as shown in this owner’s manual are for instructional purposes only, and may appear

somewhat different from those on your instrument.

* The example Operation Guide displays shown in this Manual are taken from the CVP-205, and in English.

* The bitmap fonts used in this instrument have been provided by and are the property of Ricoh co., Ltd.

* Copying of the commercially available software is strictly prohibited except for your personal use.

Trademarks:

• Apple and Macintosh are trademarks of Apple Computer, Inc.

• IBM-PC/AT is a trademark of International Business Machines Corporation.

• Windows is the registered trademark of Microsoft® Corporation.

• All other trademarks are the property of their respective holders.

This product incorporates and bundles computer programs and contents in which Yamaha owns copyrights or with respect to which it has

license to use others’ copyrights. Such copyrighted materials include, without limitation, all computer software, styles ﬁles, MIDI ﬁles, WAVE

data and sound recordings. Any unauthorized use of such programs and contents outside of personal use is not permitted under relevant

laws. Any violation of copyright has legal consequences. DON’T MAKE, DISTRIBUTE OR USE ILLEGAL COPIES.

CVP-205/203

Accessories

■

“Music Software Collection” Disk (and Music Book) (CVP-203 only)

This disk features sample songs that you can play back on your Clavinova.

■

“50 greats for the Piano” Disk (and Music Book)

■

Recording disk

Use this blank disk to save your performance.

■

Owner’s Manual

This manual contains complete instructions for operating your Clavinova.

■

Data List

This manual contains lists of voices, styles and parameters, etc.

■

Bench

A bench may be included or optional, depending on your locale.

Handling the Floppy Disk Drive (FDD) and

Floppy Disk

Precautions

Be sure to handle ﬂoppy disks and treat the disk drive with care. Follow the important precautions below.

• 3.5" 2DD and 2HD type ﬂoppy disks can be used.

To insert a ﬂoppy disk into the disk drive:

• Hold the disk so that the label of the disk is facing

upward and the sliding shutter is facing forward,

towards the disk slot. Carefully insert the disk into the

slot, slowly pushing it all the way in until it clicks into

place and the eject button pops out.

To eject a ﬂoppy disk:

Before ejecting the disk, be sure to conﬁrm that data

is not being written to the ﬂoppy disk.

If data is currently being written to the ﬂoppy disk in

the following operations, the messages “Now

executing,” “Now copying,” and “Now formatting”

appears in the display.

• Moving, copying, pasting, saving, or deleting data

(page 43 - 45).

• Naming ﬁles and folders (page 42); creating a new

folder (page 45).

• Copying a disk to an another disk (page 142);

formatting the disk (page 142).

Compatible Disk Type

Inserting/Ejecting Floppy Disks

Drive lamp

When the power is turned on, the drive lamp (at

the bottom left of the drive) lights to indicate the

drive can be used.

Eject button

CVP-205/203

• Never attempt to remove the disk or turn the power off

when the data is being written to the ﬂoppy disk.

Doing so can damage the disk and possibly the disk

drive. Press the eject button slowly as far as it will go;

the disk will automatically pop out. When the disk is

fully ejected, carefully remove it by hand.

• If the eject button is pressed too quickly, or if it is not

pressed in as far as it will go, the disk may not eject

properly. The eject button may become stuck in a half-

pressed position with the disk extending from the

drive slot by only a few millimeters. If this happens, do

not attempt to pull out the partially ejected disk, since

using force in this situation can damage the disk drive

mechanism or the ﬂoppy disk. To remove a partially

ejected disk, try pressing the eject button once again,

or push the disk back into the slot and then repeat the

eject procedure.

• Be sure to remove the ﬂoppy disk from the disk drive

before turning off the power. A ﬂoppy disk left in the

drive for extended periods can easily pick up dust and

dirt that can cause data read and write errors.

• Clean the read/write head regularly. This instrument

employs a precision magnetic read/write head which,

after an extended period of use, will pick up a layer of

magnetic particles from the disks used that will

eventually cause read and write errors.

• To maintain the disk drive in optimum working order

Yamaha recommends that you use a commercially-

available dry-type head cleaning disk to clean the

head about once a month. Ask your Yamaha dealer

about the availability of proper head-cleaning disks.

• Never insert anything but ﬂoppy disks into the disk

drive. Other objects may cause damage to the disk

drive or ﬂoppy disks.

To handle ﬂoppy disks with care:

• Do not place heavy objects on a disk or bend or apply

pressure to the disk in any way. Always keep ﬂoppy

disks in their protective cases when they are not in

use.

• Do not expose the disk to direct sunlight, extremely

high or low temperatures, or excessive humidity, dust

or liquids.

• Do not open the sliding shutter and touch the exposed

surface of the ﬂoppy disk inside.

• Do not expose the disk to magnetic ﬁelds, such as

those produced by televisions, speakers, motors, etc.,

since magnetic ﬁelds can partially or completely erase

data on the disk, rendering it unreadable.

• Never use a ﬂoppy disk with a deformed shutter or

housing.

• Do not attach anything other than the provided labels

to a ﬂoppy disk. Also make sure that labels are

attached in the proper location.

To protect your data (Write-protect Tab):

• To prevent accidental erasure of important data, slide

the disk’s write-protect tab to the “protect” position

(tab open).

Data backup

• For maximum data security Yamaha recommends that

you keep two copies of important data on separate

ﬂoppy disks. This gives you a backup if one disk is lost

or damaged. To make a backup disk use the Disk to

Disk function on page 142.

Cleaning the Disk Drive Read/Write Head

About the Floppy Disks

write-protect tab open

(protect position)

CVP-205/203

About the Display Messages

A message (information or conﬁrmation dialog) sometimes appears on the screen to

facilitate operation.

When such messages appear, simply follow the instructions as shown by pressing the

corresponding button.

Maintenance

Clean the instrument using a dry, soft cloth or slightly damp, soft cloth (wring well).

CAUTION

Do not use benzine, thinner, detergent, or chemical cloth for cleaning. Do not place vinyl, plastic, or rubber

products on the instrument.

Otherwise, the panel or keys may be discolored or degraded.

CAUTION

Before using the Clavinova, be sure to read “Precautions” on pages 3 - 4.

■

Tuning

Unlike an acoustic piano, the Clavinova does not need to be tuned. It always stays perfectly in tune.

■

Transporting

If you move to another location, you can transport the Clavinova along with other belongings. You can move the unit as

it is (assembled) or you can disassemble the unit down to the condition it was in when you ﬁrst took it out of the box.

Transport the keyboard horizontally. Do not lean it up against a wall or stand it up on its side.

Do not subject the instrument to excessive vibration or shock.

“The Clavinova-Computer Connection”

is a supplementary guidebook that describes, for beginners, what you can

do with your Clavinova and a personal computer and how to set up a Clavinova-Computer system (the manual is

not written for any speciﬁc models). The document is available as a PDF ﬁle (in English) at the following Internet

address:

Clavinova Home Page

.......................... http://www.yamahaclavinova.com/

Yamaha Manual Library

(Electronic Musical Instruments)

......... http://www2.yamaha.co.jp/manual/english/

You can select the desired

language from the Help dis-

play (page 50).

For this example, press the

[G] (YES) button to

execute formatting.

CVP-205/203

Table of Contents

Introduction

SPECIAL MESSAGE SECTION ................................... 2

PRECAUTIONS.......................................................... 3

About this Owner’s Manual and Data List .............. 5

Accessories ............................................................... 6

Handling the Floppy Disk Drive (FDD)

and Floppy Disk..................................................... 6

About the Display Messages.................................... 8

Maintenance ............................................................ 8

Application Index................................................... 12

What can you do with the Clavinova?................... 14

Setting Up the Clavinova....................................... 16

Key cover................................................................................ 16

Music Stand............................................................................ 16

Sheet Music Braces (CVP-205 only)......................................... 16

Turning the Power On and Off................................................ 17

Using headphones .................................................................. 17

Panel Controls and Terminals................................ 18

Quick Guide

Playing the Demos ................................................. 20

Song Playback ........................................................ 21

Playback of Songs ....................................................21

Playing Voices ........................................................ 25

Playing a Voice ........................................................25

Playing Two Voices Simultaneously ..........................26

Playing Different Voices with the Left

and Right Hands...................................................27

Playing Styles ......................................................... 28

Playing a style..........................................................28

Style Sections...........................................................30

One Touch Setting...................................................32

Music Finder........................................................... 33

Using the Music Finder ............................................33

Searching the Music Finder Records.........................34

Saving and Recalling Music Finder Data...................35

Playing and Practicing with the Songs.................. 36

Playing Along with the Clavinova.............................36

Recording ................................................................37

Mastering Your Favorite Songs.................................38

Basic Operations

— Organizing Your Data ....... 39

Selecting Files and Folders..................................... 41

File/Folder-related Operations .............................. 42

Naming Files/Folders ...............................................42

Moving Files/Folders ................................................43

Copying Files/Folders...............................................44

Deleting Files/Folders...............................................44

Saving Files ..............................................................45

Organizing Files by Creating a New Folder ..............45

Displaying Upper Level pages ..................................45

Entering Characters and Changing Icons .................45

Using the [DATA ENTRY] Dial ................................ 47

Direct Access — Instant Selection of Displays....... 48

Help Messages........................................................ 50

Using the Metronome............................................ 51

Adjusting the Tempo ............................................. 51

Tap Tempo ............................................................. 52

Reference

Playing the Demos.................53

Voices.....................................55

Selecting a Voice .................................................... 55

One-touch Piano Play.............................................. 56

Layer/Left — Playing Several Sounds

Simultaneously .................................................... 57

Layer — Layering Two Different Voices ................... 57

Left — Setting Separate Voices for the Left

and Right Sections of the Keyboard ..................... 58

Applying Voice Effects ........................................... 58

Using the Pedals..................................................... 59

Styles......................................60

Playing a style ........................................................ 60

Playing a Style’s Rhythm Channels only .................. 62

Adjusting the Volume Balance/Channel Muting ...... 62

Chord Fingerings.................................................... 63

Arranging the Style Pattern (SECTIONS:

MAIN A/B/C/D, INTRO, ENDING, BREAK) ......... 65

Stopping the Style Playback While Releasing Keys

(SYNC. STOP) ...................................................... 66

Selecting Intro and Ending Types (INTRO/ENDING)

... 67

Playing Fill-in patterns automatically when changing

accompaniment sections — Auto Fill In................ 67

Appropriate Panel Setting for the Selected Style

(ONE TOUCH SETTING) ...................................... 68

Automatically Changing One Touch Settings

with the Sections — OTS Link .............................. 69

Registering the Panel Controls in One Touch Setting

(ONE TOUCH SETTING) ...................................... 69

Calling Up Ideal Setups for Your Music

— Music Finder.................................................... 70

Searching the Ideal Setups — Music Finder Search.. 71

Editing Records — Music Finder Record Edit ........... 72

CVP-205/203

Song Playback ....................... 74

Compatible Song Types......................................... 74

Song Playback ........................................................ 75

Playing the Internal Songs........................................75

Playing Back Songs on Disk......................................77

Other Playback-related Operations...........................77

Muting Specific Parts

— Track1/Track2/Extra Tracks............................ 78

Repeat Playback of a Specific Range ..................... 78

Using the Practice Functions —Guide ................... 79

Practice Functions....................................................79

Practicing Music with the Guide Functions...............80

Displaying Music Notation

— Score (CVP-205 only)...................................... 81

Displaying the Lyrics .............................................. 84

Saving and Recalling Custom

Panel Setups

— Registration Memory ........ 85

Registering Panel Setups

— Registration Memory...................................... 85

Saving Your Registration Memory Setups.................86

Recalling a Registration Memory Setup ................ 87

Editing Voices

— Sound Creator ................... 88

Operation ............................................................... 88

SOUND CREATOR Parameters ............................... 89

Recording Your Performances

and Creating Songs

— Song Creator ..................... 93

About Song Recording........................................... 93

Quick Recording..................................................... 94

Multi Recording ..................................................... 95

Recording Individual Notes — Step Record .......... 97

Operation ................................................................97

Recording Melodies — Step Record (Note) ..............99

Recording Chord Changes for the Auto

Accompaniment — Step Record (Chord)............100

Select the Recording Options: Starting,

Stopping, Punching In/Out — Rec Mode......... 102

Editing a Recorded Song ..................................... 103

Editing Channel-related Parameters — Channel.....103

Editing Note Events — 1 - 16.................................106

Editing Chord Events — CHD.................................107

Editing System Events — SYS/EX. (System Exclusive)

..107

Inputting and Editing Lyrics ...................................108

Customizing the Event List — Filter........................108

Creating Accompaniment Styles

— Style Creator....................109

About Creating Accompaniment Styles............... 109

Style File Format................................................... 110

Operation ............................................................. 110

Realtime Recording — Basic ................................ 111

Step Recording..................................................... 112

Assembling an Accompaniment Style

—Assembly ........................................................ 113

Edit the Created Accompaniment Style .............. 114

Change the Rhythmic Feel — Groove and Dynamics

.. 114

Editing the Channel Data...................................... 116

Making Style File Format Settings —Parameter ..... 117

Adjust the Volume Balance

and Changing Voices

— Mixing Console ................119

Operation ............................................................. 119

Setting the Level Balance and Voice

— Volume/Voice ............................................... 120

Changing the Tone of the Voice — Filter............ 121

Changing Pitch-related Settings — Tune ............ 121

Adjusting the Effects ............................................ 122

Effect Structure ..................................................... 124

Making Global

and Other Important Settings

— Function...........................125

Operation ............................................................. 125

Fine Tuning the Pitch/Selecting a Scale

— Master Tune/Scale Tune............................... 127

Tuning the Overall Pitch — Master Tune............... 127

Selecting a Scale — Scale Tune ............................. 127

Setting Song-related Parameters

— Song Settings................................................ 129

Setting Auto Accompaniment-related Parameters

— Style Setting, Split Point,

and Chord Fingering......................................... 130

Setting Auto Accompaniment-related Parameters

— Style Setting and Split Point .......................... 130

Setting the Fingering Method — Chord Fingering

.... 131

Making Settings for the Pedals and Keyboard

— Controller...................................................... 131

Making Settings for the Pedals .............................. 131

Changing the Touch Sensitivity and Transpose

— Keyboard/Panel............................................. 133

Setting the Registration Sequence, Freeze,

and Voice Set..................................................... 134

Specifying the Order for Calling Up Registration

Memory Presets — Registration Sequence.......... 134

Maintaining Panel Settings — Freeze .................... 134

Changing the Automatically Selected Voice Settings

— Voice Set ....................................................... 135

CVP-205/203

Introduction

Quick Guide

Basic Operations - Organizing Your Data

Playing the Demos

Voices

Styles

Song Playback

Saving and Recalling Custom

Panel Setups - Registration Memory

Editing Voices - Sound Creator

Recording Your Performances

and Creating Songs - Song Creator

Creating Accompaniment Styles

- Style Creator

Adjust the Volume Balance

and Changing Voices - Mixing Console

Making Global and Other Important

Settings - Function

Using Your Clavinova with Other Devices

Appendix

Setting Harmony and Echo.................................. 135

Showing the Clavinova Display on a TV

— Video Out (CVP-205 only) ............................ 136

Setting the MIDI Parameters............................... 137

Making Overall System Settings

(Local Control, Clock, etc.) — System.................137

Transmitting MIDI Data — Transmit ......................138

Receiving MIDI Data — Receive .............................139

Setting Root Note Channels — Root ......................139

Setting Chord Channels — Chord Detect ..............139

Other Settings — Utility ...................................... 140

Making Settings for Fade In/Out, Metronome,

Parameter Lock, and Tap — CONFIG 1...............140

Making Settings for the Display, Speaker System,

and Voice Number Indication — CONFIG 2........141

Copying and Formatting Disks — Disk...................142

Entering Your Name and Language Preference

— Owner............................................................143

Restoring the Factory-programmed Settings of the

CVP-205/203 — System Reset ............................143

Using Your Clavinova

with Other Devices.............. 144

Using the Headphones (PHONES jacks)..................144

Connecting the Microphone or Guitar

(MIC./LINE IN jack) (CVP-205 only). ...................144

Connecting Audio & Video Devices .......................145

Using the Pedal (footswitch) or Foot Controller

(AUX PEDAL jack) ...............................................146

Connecting external MIDI devices

(MIDI terminals) .................................................146

Connecting to a Computer

(MIDI terminals/TO HOST terminal)....................146

What’s MIDI?.........................................................148

What You Can Do With MIDI.................................150

Data Compatibility............................................... 151

Disk format ............................................................151

Sequence Format...................................................151

Voice Allocation Format .........................................152

CVP-205/205M: Keyboard

Stand Assembly ................... 153

CVP-203: Keyboard Stand

Assembly ............................. 155

Troubleshooting.................. 157

Specifications ...................... 159

Index ................................... 161

CVP-205/203

Application Index

Use this index to ﬁnd reference pages that may be helpful for your particular

application and situation.

Listening

Listening to the internal songs................................................................................................................ page 75

Listening to disk songs ....................................................................... “Playing Back Songs on Disk” on page 77

Listening to demo songs......................................................................................................................... page 53

Listening to the demo of the selected voices .......................................................................................... page 55

Listening to songs with the special voices of the Clavinova .................................................................. page 120

Playing

Calling up the piano setting ................................................................................................................... page 56

Using the three performance control pedals........................................................................................... page 59

Playing an accompaniment that matches pitch..................................................“Transpose Assign” on page 133

Combining two voices ...................................................... “Layer — Layering Two Different Voices” on page 57

Playing separate voices with the right and left hands

...........................“Left — Setting Separate Voices for the Left and Right Sections of the Keyboard” on page 58

Changing the sound

Enhancing the sound with reverb and other effects .....................................“Applying Voice Effects” on page 58

.................................................................................................................“Adjusting the Effects” on page 122

Adjusting the Level Balance................................................................................................................. page 120

Combining two voices ...................................................... “Layer — Layering Two Different Voices” on page 57

Playing separate voices with the right and left hands

...........................“Left — Setting Separate Voices for the Left and Right Sections of the Keyboard” on page 58

Creating voices ...................................................................................................................................... page 88

Playing the auto accompaniment

Playing the accompaniment automatically............................................................................................. page 60

Calling up ideal panel settings for your music........................................................................................ page 70

Practicing

Muting the right- or left-hand part.......................................................................................................... page 80

Practicing with an accurate and steady tempo............................................. “Using the Metronome” on page 51

Recording

Recording your performance...........................................................................................................pages 94, 95

Creating a song by entering notes .......................................................................................................... page 97

Creating your original settings

Creating voices ...................................................................................................................................... page 88

Creating accompaniment styles............................................................................................................ page 109

CVP-205/203

Using a microphone (CVP-205 only)

Connecting the microphone.............. ”Connecting the Microphone or Guitar (MIC./LINE IN jack)” on page 144

Settings

Registering Panel Setups......................................................................................................................... page 85

Tuning the pitch/Selecting a scale ........................................................................................................ page 127

Making detailed settings for playing back songs ................................................................................... page 125

Making detailed settings for the auto accompaniment.......................................................................... page 130

Making settings for the pedals...........“Making Settings for the Pedals and Keyboard — Controller” on page 131

Making detailed settings for the keyboard voices ................................................................................. page 133

Showing the display on a TV (CVP-205 only)

.....................................“Showing the Clavinova Display on a TV — Video Out (CVP-205 only)” on page 136

Making detailed settings for MIDI ........................................................................................................ page 137

Connecting the Clavinova to other devices

Basic information on MIDI..................................................................................... “What’s MIDI?” on page 148

Recording your performance................ ”Playing the sounds of the Clavinova through an external audio system,

and recording the sounds to an external recorder (AUX OUT jacks)” on page 145

Raising the volume .............................. ”Playing the sounds of the Clavinova through an external audio system,

and recording the sounds to an external recorder (AUX OUT jacks)” on page 145

Outputting another instrument’s sound from the Clavinova ............ ”Outputting the sound of an external device

through the built in speakers of the Clavinova (AUX IN jacks)” on page 145

Connecting a computer........... .”Connecting to a Computer (MIDI terminals/TO HOST terminals)” on page 146

Assembling

Assembling and disassembling the Clavinova............“CVP-205/205M: Keyboard Stand Assembly” on page 153

“CVP-203: Keyboard Stand Assembly” on page 155

Quick solution

Basic functions of the Clavinova and how you can best use it .........................................................pages 12, 14

Resetting the Clavinova to the default setting

.................... “Restoring the Factory-programmed Settings of the CVP-205/203 — System Reset” on page 143

Displaying the Messages ......................................................................“About the Display Messages” on page 8

Troubleshooting ................................................................................................................................... page 157

CVP-205/203

MIN

STYLE

ACMP

MAX

AUTO FILLIN

POWER

OFF

MASTER VOLUME

FADE IN / OUT

METRONOME

START STOP

OTS LINK

BREAK

INTRO

SONG

EXTRA TRACKS

(STYLE)

TRACK 2

(L)

TRACK 1

(R)

REC TOP START / STOP REW FF REPEAT GUIDE

NEW SONG

TEMPO

SYNC.START

RESET

MAIN

TAP TEMPO

TRANSPOSE

RESET

ENDING / rit. SYNC.STOP SYNC.START START / STOP

ABCD

DIRECT ACCESS

DEMO

HELP

FUNCTION

DIGITAL

STUDIO

SOUND

CREATOR

DIGITAL

RECORDING

MIXING

CONSOLE

BALANCE

PA RT

CHANNEL

ON / OFF

1234

What can you do with the Clavinova?

SONG

Playback previously recorded

songs (page 21, 36, 74)

Enjoy a wide variety of preset songs

as well as songs on commercially

available disks.

GUIDE

Learn and practice with the

Guide functions (page 38, 79)

Play back the preset songs or the

appropriate disk software, and let

the display and guide lamps show

you when and where to play the

proper notes. It’s never been easier

or more fun to learn new music!

DEMO

Explore the Demos

(page 20, 53)

These not only showcase the

stunning voices and styles of

the instrument, they

introduce you to the various

functions and features — and

give you hands-on

experience using the

Clavinova!

STYLE

Back up your performance with Auto

Accompaniment (page 28, 60)

Playing a chord with your left hand automatically

plays the auto accompaniment backing. Select an

accompaniment style — such as pop, jazz, Latin,

etc. — and let the Clavinova be your backing band!

DIGITAL RECORDING

Record your performances

(page 93, 109)

With the powerful and easy-to-use song

recording features, you can record your

own keyboard performances, and create

your own complete, fully orchestrated

compositions — which you can then save to

the USER drive or a ﬂoppy disk for future

recall.

CVP-205/203

CVP-205

5678

EXIT

BACK NEXT

VOICE PART

ON / OFF

LAYER

LEFT

LCD

CONTRAST

ENTER

DATA

ENTRY

VOICE EFFECT

REVERB

VOICE

PIANO & HARPSI.

BRASS

MUSIC FINDER

PIANO

DSP VARIATION HARMONY / ECHO MONO LEFT HOLD

E.PIANO ORGAN & ACCORDION PERCUSSION GUITAR BASS

WOODWIND

STRINGS CHOIR & PAD SYNTH. XG USER

ONE TOUCH SETTING

REGISTRATION MEMORY

FREEZE

MEMORY

12345678

1234

LCD

The large LCD (together

with the various panel

buttons) provides

comprehensive and easy-

to-understand control of

the Clavinova’s operations.

MUSIC FINDER

Call up the perfect accompaniment

style (page 33, 70)

If you know what song you want to play,

but you don’t know which style or voice

would be right for it, let the Music Finder

help you. Just select the song title, and

the Clavinova automatically calls up the

most appropriate style and voice.

TO HOST terminal

Make music with a computer — quickly and easily (page 146)

Dive in and take advantage of the wide world of computer music

software. Connections and setup are exceptionally easy, and you can

play back your computer recorded parts with different instrument

sounds — all from a single Clavinova!

PIANO

Set up the piano —

instantly (page 56)

You can call up all the

optimum piano settings for

the Clavinova with just a

single button press — then

play the extraordinarily

realistic grand piano voice.

VOICE

Enjoy a huge variety of

realistic voices (page 25, 55)

The Clavinova features a wealth of

exceptionally authentic and

dynamic voices (more than 800)

— including piano, strings,

woodwinds, and more!

IN OUT THRU

PC-1PC-2

MIDI Mac

(

LEVEL FIXED

)

TO HOST AUX PEDAL VIDEO OUT AUX IN AUX OUTHOST SELECTMIDI

L L+R R LL+R R

CVP-205/203

Setting Up the Clavinova

■ To open the key cover:

Lift the cover slightly, then push and slide it open.

■ To close the key cover:

Slide the cover toward you and gently lower the

cover over the keys.

CAUTION

Hold the cover with both hands when opening or closing it. Do not

release it until it is fully opened or closed. Be careful to avoid catching

ﬁngers (yours or others, especially children’s) between the cover and

the unit.

CAUTION

Do not place objects such as a piece of metal or paper on top of the

key cover. Small objects placed on the key cover may fall inside the

unit when the cover is opened and may be nearly impossible to

remove. This could cause electric shock, short circuit, ﬁre or other

serious damage to the instrument.

■ To raise the music stand:

Pull the stand up and toward yourself as far as it will

go.

Flip down the two metal supports at the left and the

right on the rear of the music stand.

Lower the music stand so that it rests on the metal

supports.

■ To lower the music stand:

Pull the music stand toward yourself as far as it will

go.

Raise the two metal supports until they are ﬂat

against the rear surface of the stand.

Gently lower the music stand backward until it is all

the way down.

CAUTION

Do not try to use the music stand in a half-raised position. Also, when

lowering the stand, let the stand all the way down before releasing it.

These braces are for holding the pages of music books in

place.

■ To open

■ To close

Key cover

CAUTION

Be careful to avoid catching

your fingers when opening or

closing the cover.

Music Stand

Sheet Music Braces

(CVP-205 only)

CVP-205/203

Connect the power cord.

Insert the plugs at the ends of the cord, one into the

AC INLET on the Clavinova, and the other into a

standard AC outlet.

In some areas, a plug adapter may be provided to

match the pin conﬁguration of the AC wall outlets in

your area.

(The shape of plug differs depending on locale.)

Press the [POWER] switch.

→ The main display appears in the LCD display. The

drive lamp below the lower right end of the

keyboard also lights.

When you’re ready to turn off the power, press the

[POWER] switch again.

→ Both the display and the drive lamp below the

right end of the keyboard will turn off.

Adjusting the display contrast

If the LCD is difﬁcult to read, adjust the contrast with the

[LCD CONTRAST] knob at the right of the LCD.

Setting the volume

Use the [MASTER VOLUME] dial to adjust the volume to

an appropriate level.

CAUTION

Do not use the Clavinova at a high volume level for a long period of

time, or your hearing may be damaged.

Connect a pair of headphones to one of the [PHONES]

jacks.

Two [PHONES] jacks are provided.

Two sets of standard stereo headphones can be plugged

in. (If you are using only one pair of headphones, you

can plug them into either of these jacks.)

Turning the Power On

and Off

CVP-205

CVP-203

The drive lamp lights.

BALANCE

PART

CHANNEL

ON / OFF

POWER

OFF

LCD

CONTRAST

MIN

MAX

MASTER VOLUME

FADE IN / OUT

Using headphones

CVP-205 CVP-203

PHONES

MIN MAX

INPUT

MIC.

MIC. LINE PHONES

VOLUME

LINE IN

CVP-205/203

Panel Controls and Terminals

POWER

[ON / OFF] button (POWER)................................................ P. 17

METRONOME

[START / STOP] button (METRONOME) ............................. P. 51

MASTER VOLUME

[MASTER VOLUME] dial...................................................... P. 17

[FADE IN / OUT] button........................................................ P. 66

SONG

[EXTRA TRACKS (STYLE)] button...................................... P. 78

[TRACK 2 (L)] button............................................................ P. 78

[TRACK 1 (R)] button ........................................................... P. 78

[REC] button ........................................................................ P. 93

[TOP] button......................................................................... P. 77

[START / STOP] button (SONG) .......................................... P. 75

[REW] button........................................................................ P. 77

[FF] button............................................................................ P. 77

[REPEAT] button .................................................................. P. 78

[GUIDE] button..................................................................... P. 79

TEMPO

[E] [F] buttons (TEMPO)............................................... P. 51

[TAP TEMPO] button............................................................ P. 52

TRANSPOSE

[E] [F] buttons (TRANSPOSE) ................................... P. 133

STYLE

[ACMP] button...................................................................... P. 61

[AUTO FILLIN] button........................................................... P. 67

[OTS LINK] button................................................................ P. 69

[BREAK] button.................................................................... P. 65

[INTRO] button ............................................................... P. 31, 67

MAIN [A] button.................................................................... P. 65

MAIN [B] button.................................................................... P. 65

MAIN [C] button ................................................................... P. 65

MAIN [D] button ................................................................... P. 65

[ENDING / rit.] button..................................................... P. 31, 67

[SYNC.STOP] button ........................................................... P. 66

[SYNC.START] button.......................................................... P. 61

[START / STOP] button (STYLE) ......................................... P. 61

[DEMO] button ..................................................................... P. 53

[HELP] button ...................................................................... P. 50

[FUNCTION] button ........................................................... P. 125

DIGITAL STUDIO

[SOUND CREATOR] button................................................. P. 88

[DIGITAL RECORDING] button ................................... P. 93, 109

[MIXING CONSOLE] button............................................... P. 119

DISPLAY CONTROL

[A] - [J] buttons..................................................................... P. 41

[BALANCE] button ............................................................... P. 62

[CHANNEL ON / OFF] button ........................................ P. 62, 77

[DIRECT ACCESS] button................................................... P. 48

[BACK] button ................................................................ P. 41, 47

[NEXT] button ................................................................ P. 41, 47

VOICE PART ON / OFF [LAYER] button.............................. P. 57

VOICE PART ON / OFF [LEFT] button ................................ P. 57

[1▲▼] - [8▲▼] buttons ................................................. P. 39 - 46

[LCD CONTRAST] knob ...................................................... P. 17

[ENTER] button.................................................................... P. 47

[DATA ENTRY] dial............................................................... P. 47

[EXIT] button........................................................................ P. 41

VOICE EFFECT

[REVERB] button ................................................................. P. 58

[DSP] button......................................................................... P. 58

MIN

STYLE

ACMP

MAX

AUTO FILLIN

POWER

OFF

MASTER VOLUME

FADE IN / OUT

METRONOME

START STOP

OTS LINK

BREAK

INTRO

SONG

EXTRA TRACKS

(STYLE)

TRACK 2

(L)

TRACK 1

(R)

REC TOP START / STOP REW FF REPEAT GUIDE

NEW SONG

TEMPO

SYNC.START

RESET

MAIN

TAP TEMPO

TRANSPOSE

RESET

ENDING / rit. SYNC.STOP SYNC.START START / STOP

ABCD

DIRECT ACCESS

DEMO

HELP

FUNCTION

DIGITAL

STUDIO

SOUND

CREATOR

DIGITAL

RECORDING

MIXING

CONSOLE

BALANCE

PART

CHANNEL

ON / OFF

1234

CVP-205

IN OUT THRU

PC-1PC-2

MIDI Mac

(

LEVEL FIXED

)

TO HOST AUX PEDAL VIDEO OUT AUX IN AUX OUTHOST SELECTMIDI

L L+R R L L+R R

CVP-203

PC-1 PC-2

MIDIMac

INOUTTHRU

MIDI

TO HOSTAUX PEDAL HOST SELECT

AUX OUT AUX IN

LL L+RRR L L+RR

(

LEVEL FIXED

)

CVP-205

MIN MAX

INPUT

MIC.

MIC. LINE PHONES

VOLUME

LINE IN

CVP-203

PHONES

5 76

8 9 10 11 12 13 14

15 16 17

18 20 21 22 23 24 25 26 27 28 29 30

69 70 71 72 73 74 75 76 72 71 70 76 75 7469

65 66 6867

CVP-205/203

[VARIATION] button ............................................................. P. 58

[HARMONY / ECHO] button ................................................ P. 59

[MONO] button..................................................................... P. 59

[LEFT HOLD] button ............................................................ P. 59

VOICE

VOICE buttons ..................................................................... P. 55

MUSIC FINDER

[MUSIC FINDER] button ...................................................... P. 70

ONE TOUCH SETTING

[1] - [4] buttons (ONE TOUCH SETTING)............................ P. 68

PIANO Setting

[PIANO] button..................................................................... P. 56

REGISTRATION MEMORY

[FREEZE] button.................................................................. P. 87

[1] – [8] buttons (REGISTRATION MEMORY) ..................... P. 85

[MEMORY] button ................................................................ P. 85

Floppy disk drive (3.5”)........................................................... P. 6

Keyboard guide lamps ......................................................... P. 79

Microphone and Headphone Connectors

[INPUT VOLUME] knob...................................................... P. 144

[MIC. LINE IN] jack............................................................. P. 144

[MIC. LINE] switch.............................................................. P. 144

[PHONES] jacks................................................................. P. 144

Connectors

MIDI [THRU] [OUT] [IN] terminals...................................... P. 146

[HOST SELECT] switch ..................................................... P. 146

[TO HOST] terminal ........................................................... P. 147

[AUX PEDAL] jack.............................................................. P. 146

[VIDEO OUT] jack.............................................................. P. 145

AUX IN [L / L+R] [R] jacks.................................................. P. 145

AUX OUT [L / L+R] [R] jacks.............................................. P. 145

AUX OUT (LEVEL FIXED) [L] [R] jacks ............................. P. 145

Pedals

Left pedal ............................................................................. P. 59

Sostenuto pedal ................................................................... P. 59

Damper pedal ...................................................................... P. 59

The Panel Logos

The logos printed on the Clavinova panel indicate standards/

formats it supports and special features it includes.

GM System Level 1

“GM System Level 1” is an addition to the MIDI standard which

guarantees that any data conforming to the standard will play

accurately on any GM-compatible tone generator or synthesizer

from any manufacturer.

XG Format

XG is a new Yamaha MIDI speciﬁcation which signiﬁcantly

expands and improves on the “GM System Level 1” standard with

greater voice handling capacity, expressive control, and effect

capability while retaining full compatibility with GM. By using the

Clavinova’s XG voices, it is possible to record XG-compatible

song ﬁles.

XF Format

The Yamaha XF format enhances the SMF (Standard MIDI File)

standard with greater functionality and open-ended expandability

for the future. The Clavinova is capable of displaying lyrics when

an XF ﬁle containing lyric data is played. (SMF is the most

common format used for MIDI sequence ﬁles. The Clavinova is

compatible with SMF Formats 0 and 1, and records “song” data

using SMF Format 0.)

Disk Orchestra Collection

The DOC voice allocation format provides data playback

compatibility with a wide range of Yamaha instruments and MIDI

devices.

Style File Format

The Style File Format (SFF) is Yamaha’s original style ﬁle format,

which uses a unique conversion system to provide high-quality

automatic accompaniment based on a wide range of chord types.

The Clavinova uses the SFF internally, reads optional SFF style

disks, and creates SFF styles using the Style Creator feature.

5678

EXIT

BACK NEXT

VOICE PART

ON / OFF

LAYER

LEFT

LCD

CONTRAST

ENTER

DATA

ENTRY

VOICE EFFECT

REVERB

VOICE

PIANO & HARPSI.

BRASS

MUSIC FINDER

PIANO

DSP VARIATION HARMONY / ECHO MONO LEFT HOLD

E.PIANO ORGAN & ACCORDION PERCUSSION GUITAR BASS

WOODWIND

STRINGS CHOIR & PAD SYNTH. XG USER

ONE TOUCH SETTING

REGISTRATION MEMORY

FREEZE

MEMORY

12345678

1234

57 58

59 60 61 62

51 52 54 5553

Quick Guide

Quick Guide . . . . . . . . . . . . . . . . . . . . . . . . .

Playing the Demos

The Clavinova features an extensive variety of Demo

songs, that showcase its rich, authentic voices and its

dynamic rhythms and styles.

What’s more, there’s a special selection of Demo

functions. These take you through a hands-on journey of

all the important features and functions of the instrument

— letting you see ﬁrsthand how to effectively use the

Clavinova in your own music.

Press the [EXIT] button to exit from the demo mode and return to the MAIN display when you’ve ﬁnished playing the

demo songs.

When you’re done with the Demos, you can get to know your Clavinova even better with these functions:

• Preset Song (Song Book) playback (CVP-205) (page 21)

• Disk Song Playback (CVP-203) (page 21)

• Short demo playback of the selected voice (in the Voice Open display; page 26).

Reference

on page 53

Demo button

DEMO

HELP

FUNCTION

2 Press the [BACK]/[NEXT] button to select the Demo

categories.

BACK NEXT

Voice Demos showcase the

voices of the CVP-205/203.

Style Demos introduce you

to the rhythms and accom-

paniment styles of the CVP-

205/203 (page 53).

For this example, FUNCTION

is selected. Function Demos

demonstrate many of the

different functions on the

CVP-205/203.

1 Pressing the [DEMO] button

automatically plays back the

Demo songs at random.

Press any of the [A] to [J] buttons or [8▼] (AUTO) button (FUNCTION page only) to select the Demo songs.

For this example, press the [8▼] (AUTO) button.

All of the function demos are played back in sequence.

VOICE PART

ON / OFF

LAYER

LEFT

12345678

For details about the Demos,

refer to page 53.

Song Playback

Quick Guide

Song Playback

Here’s where all of the amazing voices, effects, rhythms, styles and other sophisticated features of

the Clavinova come together — in songs!

As you heard in the Demos, the Clavinova contains many built-in recordings. But there’s more. On the CVP-203, check

out the included disk; on the CVP-205 or 203, call up the Song Open (PRESET) display. And there’s an even greater

wealth of song material you can enjoy with your Clavinova — in commercially available software.

The following songs are compatible for playback on the CVP-205/203. Refer to pages 74, 151 for more details on the

logos.

Playback of Songs

1 If you want to play back a disk song, insert an appropriate disk containing song data into the disk drive.

Reference

on page 74

Song related buttons

Floppy disk drive

BALANCE and

CHANNEL buttons

Make sure that the Lan-

guage setting for the instru-

ment (page 143) is the same

as that of the ﬁle name of the

song that you are playing

back.

Disks bearing this logo contain song data for voices deﬁned in the GM standard.

Disks bearing this logo contain song data using the XG format, an extension of the GM

standard that provides a wider variety of voices and more comprehensive sonic control.

Disks bearing this logo contain song data for voices deﬁned in Yamaha’s DOC format.

Songs containing a large

amount of data may not be

able to be read properly by

the instrument, and as such

you may not be able to

select them. The maximum

capacity is about 200–

300KB, however this may

differ depending on the data

contents of each song.

• Make sure to read the

section “Using the Floppy

Disk Drive (FDD) and

Floppy Disks” on page 6.

CAUTION

Song Playback

Quick Guide

2 Press the [A] button to call up the Song Open display.

If the MAIN screen is not displayed, press the [DIRECT ACCESS] button followed by the [EXIT] button.

3 PRESET only

Press the [A] button to select the preset songs (Song Book; CVP-205 only) folder.

Press the [BACK]/[NEXT] button to select the drive.

In the example display of the CVP-205 at left, the

PRESET page is selected. At right is a display from

the CVP-203, with FLOPPY DISK selected.

PRESET FLOPPY DISK

From the MAIN display (the

display shown when the

power is turned on), you can

select songs, voices, accom-

paniment styles, etc.

Song Playback

Quick Guide

4 Press one of the [A] to [J] buttons to select a song ﬁle.

5 Press the SONG [START/STOP] button to start playback.

6 While the song is playing, try using the Mute function to turn certain instrument channels off or on —

letting you craft dynamic arrangements on the ﬂy!

1) Press the [CHANNEL ON/OFF] button.

2) Press the [1 - 8▲▼] button corresponding to the channel you wish to turn on or off.

REC TOP START / STOP

NEW SONG

SYNC.START

• To rewind or fast forward to the playback point of the song, press the [REW] or [FF] button.

• With song data software (Standard MIDI format 0) that includes lyrics, you can view the lyr-

ics on the display during playback. You can also view the score (CVP-205 only). See

pages 81 and 84 for details.

PA RT

CHANNEL

ON / OFF

12345678 12345678

If the STYLE tab is

selected, press this button

again.

Song Playback

Quick Guide

7 Finally, take the producer’s seat and try your hand at mixing. These Balance controls let you adjust the levels

of the individual parts — the song, the style, your singing (CVP-205 only), and your playing.

1) Press the [BALANCE] button.

2) Press the [1 - 8▲▼] button corresponding to the part of which the volume you wish to adjust.

8 Press the SONG [START/STOP] button to stop playback.

12345678

BALANCE

You can call up a full set of

mixing controls by pressing

the [MIXING CONSOLE]

button (page 119).

REC TOP START / STOP

NEW SONG

SYNC.START

• The [FADE IN/OUT] but-

ton (page 66) can be used

to produce smooth fade-

ins and fade-outs when

starting and stopping the

song, as well as the

accompaniment.

Playing Voices

Quick Guide

Playing Voices

The Clavinova features a stunning variety of over 800 dynamic, rich and realistic voices. Try playing

some of these voices now and hear what they can do for your music. Here, you’ll learn how to

select individual voices, combine two voices in a layer, and split two voices between your left and right hands.

Playing a Voice

1 Press the [F] button to call up the menu for selecting the MAIN voice.

If the MAIN screen is not displayed, press the [DIRECT ACCESS] button followed by the [EXIT] button.

2 Select a voice group.

Reference

on page 55

Voice related buttons

VOICE PART

ON / OFF

LAYER

LEFT

The voice you’re selecting

here belongs to the MAIN

part, and is called the MAIN

voice. (See page 57 for more

information.)

Yo u ’ll want to hear the MAIN

voice all by itself — so make sure

that the LAYER and LEFT parts

are turned off.

VOICE

PIANO & HARPSI.

BRASS

E.PIANO ORGAN & ACCORDION PERCUSSION GUITAR BASS

WOODWIND

STRINGS CHOIR & PAD SYNTH. XG USER

For this example, STRINGS

is selected.

Press the [BACK]/[NEXT]

button to select the memory

location of the voice. For this

example, PRESET is

selected.

Playing Voices

Quick Guide

3 Select a voice.

4 Play the voices.

Naturally, you can play the voice yourself from the keyboard, but you can also

have the Clavinova demonstrate the voice for you. Simply press the [8▲] button

from the display above, and a Demo of the voice plays automatically.

Playing Two Voices Simultaneously

1 Press the VOICE PART ON/OFF [LAYER] button to

turn the LAYER part on.

2 Press the [G] button to select the LAYER part.

3 Select a voice group.

Here, we’ll select a lush pad to ﬁll out the sound. Call up the “CHOIR & PAD” group.

4 Select a voice.

For example, select “Hah Choir.”

5 Play the voices.

Now, you can play two different voices together in a

rich sounding layer — the MAIN voice you selected in

the previous section, plus the new LAYER voice you’ve

selected here.

And that’s just the beginning. Check out these other voice-related features:

• Instant setup of the Clavinova for piano play — with the press of a single button (page 56).

• Create your own original voices — quickly and easily — by changing the settings of existing voices (page 88).

• Set up your favorite panel settings — including voices, styles, and more — and call them up whenever you need

them (page 85).

For this example,

”Orchestra” is

selected.

Press the corresponding buttons to select the

other pages — and discover even more voices.

Press the [8▲] button to start the

Demo for the selected voice. To stop

the Demo, press this button again.

There’s more to the Demo features

than just voices, though–for more

information, see page 53.

You can instantly jump back

to the Main display by “dou-

ble-clicking” on one of the [A]

- [J] buttons.

VOICE PART

ON / OFF

LAYER

LEFT

VOICE

PIANO & HARPSI.

BRASS

E.PIANO ORGAN & ACCORDION PERCUSSION GUITAR BASS

WOODWIND

STRINGS CHOIR & PAD SYNTH. XG USER

Playing Voices

Quick Guide

Playing Different Voices with the Left and Right Hands

1 Press the VOICE PART ON/OFF [LEFT] button to turn the

LEFT part on.

2 Press the [H] button to select the LEFT part.

3 Select a voice group.

Here, we’ll select the “STRINGS” group — so that you can play rich, orchestral chords with your left hand.

4 Select a voice, then press the [EXIT] button to return to the MAIN display.

For example, select “Symphon. Str.”

5 Press the [I] button to call up the SPLIT POINT display. From here, you can set the particular key on the

keyboard that separates the two voices — called the Split Point. To do this, simultaneously hold down the [F]

or [G] button and press the desired key on the keyboard. (For more information, see page 130.)

6 Play the voices.

The notes you play with your left hand sound one voice, while the notes you play with your right sound a

different voice (or voices).

MAIN and LAYER voices are meant to be played with the right hand. The LEFT voice is played with the left

hand.

7 Press the [EXIT] button to return to the MAIN display.

LAYER

LEFT

VOICE

PIANO & HARPSI.

BRASS

E.PIANO ORGAN & ACCORDION PERCUSSION GUITAR BASS

WOODWIND

STRINGS CHOIR & PAD SYNTH. XG USER

Split Point

LEFT

MAIN/LAYER

EXIT

Playing Styles

Quick Guide

Playing Styles

The Clavinova has a huge variety of musical “styles” that you can call upon to back up your own

performance. They give you anything from a simple, yet effective piano backing or percussion

accompaniment to a full band or orchestra.

Playing a style

1 Press the [D] button to call up the style group.

If the MAIN screen is not displayed, press the [DIRECT ACCESS] button followed by the [EXIT] button.

2 Select a style group and a style.

Reference

on page 60

Style related buttons

Press the

[BACK]/[NEXT]

button to select

the memory

location of the

style. For this

example,

PRESET is

selected.

For this example,

EuroTrance is selected.

For this example, Dance is

selected.

Playing Styles

Quick Guide

3 Turn ACMP on.

The speciﬁed left-hand section of the keyboard becomes the “Auto Accompaniment” section, and chords

played in this section are automatically detected and used as a basis for fully automatic accompaniment with

the selected style.

4 Turn SYNC.START on.

5 As soon as you play a chord with your left hand, the style starts.

For this example, play a C major chord (as shown below).

6 Change the tempo by using the TEMPO[ ] [ ] buttons if necessary.

Simultaneously press the TEMPO [ ] [ ] buttons to return the tempo to its

original setting. Press the [EXIT] button to leave the TEMPO display.

7 Try playing other chords with your left hand.

For information on how to enter chords, see “Chord Fingerings” on page 63.

8 Press the STYLE [START/STOP] button to stop the style.

And there’s much more. Check out these other style-related features:

• Easily create your own original styles (page 109).

• Set up your favorite panel settings — including styles, voices, and more — and call them up whenever you need

them (page 85).

ACMP

Auto Accompaniment

section

Split Point

• The point on the keyboard

that separates the auto

accompaniment section

and the right-hand sec-

tion of the keyboard is

called the “split point.”

Refer to page 130 for

instructions on setting the

split point.

SYNC.START

Split Point

Auto Accompaniment

section

The Tempo can also be

adjusted by using the [TAP

TEMPO] button (page 52).

Playing Styles

Quick Guide

Style Sections

Each style in the auto accompaniment is made up of “sections.” Since each section is a rhythmic variation of the basic

style, you can use them to add spice to your performance and mix up the beats — while you’re playing. Intros, Endings,

Main patterns, and Breaks — they’re all here, giving you the dynamic elements you need to create professional-

sounding arrangements.

1 - 4 Use the same operations as in “Playing a style” on pages 28 and 29.

5 Press the [INTRO] button.

6 As soon as you play a chord with your left hand, the Intro starts.

For this example, play a C major chord (as shown below).

When the playback of the intro is ﬁnished, it automatically leads into main section.

7 Press any of the MAIN [A] to [D] buttons or [BREAK] button

as desired. (See the Accompaniment Structure on the next

page.)

Embellish and enhance your melodies — with the automatic Harmony and Echo effects

This powerful performance feature lets you automatically add harmony notes to the melodies you play with your

right hand — based on the chords you play with your left. Tremolo, Echo, and other effects are available, too.

1 Turn HARMONY/ECHO on.

2 Turn ACMP on (page 28).

3 Play a chord with your left hand and play some notes in the right-hand range of the

keyboard.

The CVP-205/203 has various Harmony/Echo types (page 135).

The Harmony/Echo type may change according to the selected MAIN voice.

• Harmony/Echo is just one of the many Voice Effects you can use. Try out some of

the other effects and see how they can enhance your performance (page 58).

INTRO This is used for the beginning of the song. When the intro ﬁnishes playing, accompaniment shifts to the

main section.

MAIN This is used for playing the main part of the song. It plays an accompaniment pattern of several measures,

and repeats indeﬁnitely until another section’s button is pressed.

BREAK This lets you add dynamic variations and breaks in the rhythm of the accompaniment, to make your

performance sound even more professional.

ENDING This is used for the ending of the song. When the ending is ﬁnished, the auto accompaniment stops

automatically.

VOICE EFFECT

REVERB DSP VARIATION HARMONY / ECHO MONO LEFT HOLD

For details about Harmony/

Echo types, refer to the sep-

arate Data List.

BREAK

INTRO

MAIN

ENDING / rit.

ABCD

Split Point

Auto Accompaniment

section

BREAK

INTRO

MAIN

ENDING / rit.

ABCD

Playing Styles

Quick Guide

8 Press the [AUTO FILL IN] button to add a ﬁll-in, if

necessary.

Fill-in patterns play automatically between each change in

the Main sections.

9 Press the [ENDING] button.

This switches to the ending section. When the ending is

ﬁnished, the style automatically stops.

■ Accompaniment Structure

AUTO FILLIN

BREAK

INTRO

MAIN

ENDING / rit.

ABCD

INTRO (page xx)

MAIN VARIATION

Press the [ENDING] button.

INTRO A INTRO B INTRO C

ENDING (page xx)

ENDING A ENDING B ENDING C

INTRO D

ENDING D

You can have the

ending gradually slow

down (ritardando) by

pressing the [ENDING]

button again while the

ending is playing back.

MAIN

VARIATION

MAIN

VARIATION

MAIN

VARIATION

MAIN

VARIATION

via BREAK

(max. four patterns)

INTRO (page 67)

ENDING (page 67)

• An Intro doesn’t necessarily have to be at the beginning! If you want, you can play an Intro section in the middle of your performance by

simply pressing the [INTRO] button at the desired point.

• Watch your timing with the Break sections. If you press a [BREAK] button too close to the end of the measure (i.e., after the ﬁnal eighth

note), the Break section starts playing from the next measure. This also applies to the Auto Fill-in.

• Mix up your intros and use any of the other sections to start the style, if you want.

• If you want to come back into the style right away after an Ending, simply press the [INTRO] button while the Ending section is playing.

• If you press the [BREAK] button while the ending is playing, the break will immediately start playing, continuing with the main section.

Playing Styles

Quick Guide

One Touch Setting

One Touch Setting is a powerful and convenient feature that automatically calls up the most appropriate panel settings

(voice number, etc.) for the currently selected style, with the touch of a single button. This is a wonderful way to

instantly reconﬁgure all the settings on the Clavinova to match the style you want to play.

1 Select a style (page 28).

2 Press one of the [ONE TOUCH SETTING]

buttons.

Not only does this instantly call up all the settings

(voices, effects, etc.) that match the current style

(see page 68) — it also automatically turns on

ACMP and SYNC. START, so that you can

immediately start playing the style.

3 As soon as you play a chord with your left hand, the auto

accompaniment starts.

4 Play melodies with your right hand and play various chords

with your left hand.

5 Try out other One Touch Setting setups.

You can also create your own One Touch Setting

setups.

For details, refer to page 69.

• Here’s another way to further automate musical changes and spice up your performance: Use the convenient OTS

(One Touch Setting) Link function to automatically change One Touch Settings when you select a different Main

section (page 69).

Other Controls

FADE IN/OUT The [FADE IN/OUT] button can be used to produce smooth fade-ins and fade-outs (page 66)when starting and stopping

the style.

TAP TEMPO The style can be started at any tempo you desire by “tapping” out the tempo with the [TAP/TEMPO] button. For details,

see page 52.

SYNC.STOP When Synchro Stop is on, you can stop and start the style anytime you want by simply releasing or playing the keys (in

the Auto Accompaniment section of the keyboard). This is a great way to add dramatic breaks and accents to your

performance. For details, see page 66.

FADE IN / OUT

TAP TEMPO

SYNC.STOP

ONE TOUCH SETTING

buttons

ONE TOUCH SETTING

1234

Split Point

Auto Accompaniment

section

ONE TOUCH SETTING

1234

Music Finder

Quick Guide

Music Finder

If you want to play in a certain song but don’t know which style and voice settings would be appropriate, the

convenient Music Finder can help you out. Simply select the song name from the Music Finder and the CVP-205/203

automatically makes all appropriate panel settings to let you play in that music style!

Using the Music Finder

1 Press the [MUSIC FINDER] button.

2 Select a record.

For this example, press the [1 - 3▲▼] button to select a record by song title.

3 Play along with the style playback.

Press the [EXIT] button to return to the MAIN display.

Reference

on page 70

MUSIC FINDER button

MUSIC FINDER

Select the desired

record.

Press the [BACK]/[NEXT]

button to select the desired

page of records. For this

example, ALL is selected.

Split Point

Auto Accompaniment

section

You can also have the voice

and other important settings

change automatically with

the style changes. To do this,

turn on OTS LINK (page 69)

and set the OTS LINK TIM-

ING (page 130) to “REAL.”

Music Finder

Quick Guide

Searching the Music Finder Records

The Music Finder is also equipped with a convenient search function that lets you enter a song title or keyword — and

instantly call up all the records that match your search criteria.

1 Press the [MUSIC FINDER] button.

2 Press the [I] button to call up the MUSIC FINDER SEARCH 1 display.

MUSIC FINDER

The results of Search 1 and

2 appear in the correspond-

ingly numbered SEARCH 1/

2 displays.

Press the [8▲] (START SEARCH)

button.

The search function calls up all

records that contain the entered

word or words.

Press the [F], [G]

and [H] to clear

the previous

conditions, if

necessary.

For this example,

press the [A]

button to call up

the display for

inputting the song

title.

Refer to page 46 for instruc-

tions on entering characters.

Enter the song title,

then press the [8▲]

(OK) button.

For this example,

ANY is selected.

For this example,

ALL is selected.

Music Finder

Quick Guide

7 Select a record (see step #2 on page 33) and play along with the style playback.

Press the [EXIT] button to return to the MAIN display.

You can also create your own Music Finder setups and save them to ﬂoppy disk (pages 39 and 45). In this

way, you can expand your Music Finder collection by exchanging them with other Clavinova users.

Saving and Recalling Music Finder Data

To save your Music Finder data, call up the MUSIC FINDER Open/Save window from the

SYSTEM RESET page (page 143) of the UTILITY display, and follow the same procedure as

that in the Open/Save window for Voice (page 39, 45). To recall the saved data, execute

the appropriate operation from the MUSIC FINDER’s Open/Save window. Records can be

replaced or added (page 72).

In the instructions above, all Music Finder data is handled together. Besides this, when you save or load style ﬁles, the

Music Finder data that uses the relevant style ﬁle(s) is stored or added automatically. When you copy or move a style ﬁle

on a ﬂoppy disk to the USER drive (page 43, 44), the record which was recorded when storing the relevant style is

automatically added to the CVP-205/203.

• In the example above, you speciﬁed a song title, but you can also look for relevant records by keyword or music

genre — for example, Latin, 8-beat, etc. (page 71).

Split Point

Auto Accompaniment

section

Music Finder data is compat-

ible for both the CVP-205

and the CVP-203.

Playing and Practicing with the Songs

Quick Guide

Playing and Practicing with the Songs

Playing Along with the Clavinova

In this section, try using the Clavinova’s song playback features to cancel or mute the right-hand melody while you play

the part yourself. It’s like having a very talented and versatile playing partner accompany you while you perform.

If you haven't yet mastered the melody part, take a look at the section “Mastering Your Favorite Songs” on page 38, and

practice it a while.

1 - 4 Use the same operations as in “Song Playback” on pages 21 - 23.

5 Press the [TRACK 1] button to cancel the right hand melody part.

6 If you want to have the notation displayed as you play (CVP-205 only), press the [C] button. If you want to

see the lyrics, press the [B] button.

If the MAIN screen is not displayed, press the [DIRECT ACCESS] button followed by the [EXIT] button.

7 Press the SONG [START/STOP] button and play the part.

8 Press the SONG [START/STOP] button to stop playback.

Reference

on page 74

Song related buttons

TRACK 1

(R)

To cancel the left hand part,

press the [TRACK 2] button

If the selected song does not

contain lyric data, lyrics are

not displayed.

• If you want to start the song right

away without an intro, use the Sync

Start function. To set Sync Start to

standby, simultaneously hold down

the [TOP] button and press the

SONG [START/STOP] button. Song

playback starts automatically the

moment you start playing the mel-

ody.

• If you can hear the Clavinova playing

the melody part as well, check the

channel setting for the melody part in

the song data, and change the chan-

nel assigned to Track 1 (page 129).

You can also change the song chan-

nel itself permanently (page 104).

REC TOP START / STOP

NEW SONG

SYNC.START

REC TOP START / STOP

NEW SONG

SYNC.START

Playing and Practicing with the Songs

Quick Guide

Recording

The Clavinova lets you record, too — quickly and easily. Try out the Quick Recording feature now and capture your

keyboard performance.

1 - 3 Select a voice for recording. Use the same operations as in “Playing a Voice” on pages 25, 26.

4 Press the [REC] and [TOP] buttons simultaneously to select “New Song“ for recording.

5 Simultaneously hold down the [REC] button and press the [TRACK1] button.

6 Recording starts as soon as you start playing the keyboard.

7 When you’ve ﬁnished recording, press the [REC] button.

8 To hear your newly recorded performance, return the song to the beginning by

using the [TOP] button and press the SONG [START/STOP] button.

9 Save the recorded data as required (pages 39, 45).

REC TOP START / STOP REW FF REPEAT

NEW SONG

SYNC.START

REC

SONG

EXTRA TRACKS

(STYLE)

TRACK 2

(L)

TRACK 1

(R)

REC

The recorded data will be

lost if you turn off the power.

To keep your important

recordings, you’ll need to

save them to the User drive

or ﬂoppy disk.

CAUTION

REC TOP START / STOP

NEW SONG

SYNC.START

Playing and Practicing with the Songs

Quick Guide

Mastering Your Favorite Songs

The Clavinova has several very useful practice features that help learn and master

recorded songs. Here, you’ll try out the Follow Lights function, and use the special guide

lamps to help you play the right notes.

1 - 6 Use the same operations as in “Playing Along with the Clavinova” on

page 36.

For this example, you practice the right hand part of “Playing Along with

the Clavinova.”

7 Press the [GUIDE] button.

8 Press the SONG [START/STOP] button and practice the missing (muted) part, according to the key guide

lamps.

If you want, you can adjust the tempo by pressing the TEMPO[ ] [ ] buttons.

9 You can use the powerful Repeat function to practice and master difﬁcult parts. Simply specify a short

phrase you want to work on and repeat it until you’ve got it down.

1) While the song is playing back, press the [GUIDE] button once to turn the GUIDE function off.

2) Just before the desired phrase comes around, press the [REPEAT] button to designate the beginning point

for Repeat.

3) Just after the phrase ﬁnishes, press the [REPEAT] button again to designate the end point.

4) Turn the GUIDE function on again.

Press the SONG [START/STOP] button to stop playback.

Before Practicing

Before starting a practice

session, play back the entire

song (without canceling any

parts) and listen to it care-

fully. This will give you a

clear idea of how the song

should be played, and will

make your practice sessions

progress more smoothly. If

you want to hear only the

melody part, turn the

[TRACK 2] and [EXTRA

TRACKS] buttons off.

GUIDE

TEMPO

RESET

REC TOP START / STOP

NEW SONG

SYNC.START

See pages 79 and 129 for

more information on the

Guide function.

REC TOP START / STOP

NEW SONG

SYNC.START

CVP-205/203

Basic Operations — Organizing Your Data

The CVP-205/203 utilizes a variety of data types — including voices, accompaniment styles, songs and registration

memory settings. Much of this data is already programmed and contained in the CVP-205/203; you can also create and

edit your own data with some of the functions on the instrument.

All this data is stored in separate ﬁles — just as is done on a computer.

Here, we’ll show you how to use the basic operations of the display controls in handling and organizing the data of the

CVP-205/203 in ﬁles and folders.

Files can be opened, saved, named, moved, or deleted in their respective Open/Save displays. You can select these

displays according to their respective ﬁle types, as well: Song, Voice, Style, etc. Moreover, you can organize your data

efﬁciently by putting various ﬁles of the same type into a single folder.

The Open/Save displays for Song, Voice, Style, and Registration Bank can be called up from the MAIN display (the

display shown when the power is turned on) by pressing the appropriate [A] - [J] button.

The following Open/Save display types

are also available; however, these are

selected from displays other than the

MAIN display (page 143

• SYSTEM SETUP

• MIDI SETUP

• USER EFFECT

• MUSIC FINDER

Open/Save display for Song (page 75)

handles the Song ﬁles.

Open/Save display for Voice (page 55)

handles the Voice ﬁles.

Open/Save display for Style (page 60)

handles the Style ﬁles.

Open/Save display for Registration Bank (page 86)

handles the Registration Bank ﬁles.

If the MAIN screen is not displayed,

press the [DIRECT ACCESS] button

followed by the [EXIT] button.

Basic Operations — Organizing Your Data

CVP-205/203

Example — Open/Save display for Voice

Each Open/Save display consists of PRESET, USER, and FLOPPY DISK drive pages.

BACK NEXT

PRESET drive

The ﬁles that are pre-

programmed and installed

internally to the CVP-205/203

are kept here. Preset ﬁles can be

loaded but cannot be re-written.

However, you can use a preset

ﬁle as a basis for creating your

own original ﬁle (which can be

saved in the USER or FLOPPY

DISK drive).

USER drive

Files kept here are those

containing your own original

data, created or edited using the

various functions of the CVP-

205/203. They are stored

internally to the CVP-205/203.

FLOPPY DISK drive

You can also store your original

data to ﬂoppy disk.

Commercially available disk

software can also be called up

here. Naturally, these ﬁles are

available only when the

appropriate disk is inserted in

the ﬂoppy disk drive.

File

All data, both pre-

programmed and your own

original, are stored as “ﬁles.”

Current Memory

“Current Memory” is the area where the voice is called up when

you select a voice. Also it is the area where you edit your voice

using the SOUND CREATOR function. Your edited voice should

then be saved as a ﬁle in the USER or FLOPPY DISK drive.

Recording songs (page 93) and creating accompaniment styles

(page 109) are done within the current memory. Please make

sure to properly save this data to the USER/FLOPPY DISK drive as

a ﬁle or ﬁles. The data will be lost if you turn off the power

without saving.

Calls up the upper

level directory page.

In this example, the

voice folder selection

page can be called

up.

Changes drives among

PRESET, USER and

FLOPPY DISK.

Basic Operations — Organizing Your Data

CVP-205/203

Select a ﬁle shown in the display. In this example, we’ll select a voice ﬁle.

First, press the VOICE [PIANO & HARPSI] button to call up the display containing the ﬁles.

This display (“Open/Save” display) is typical of those used to call up and store ﬁles (voice ﬁles).

The CVP-205/203 already contains a variety of voices in the PRESET section. You can store your own original voices

created with the Sound Creator function to the USER or FLOPPY DISK section.

Selecting Files and Folders

BACK NEXT

ENTER

DATA

ENTRY

END

Select “PRESET,” “USER,” or

“FLOPPY DISK” by using the

[BACK][NEXT] button.

Use the [1▲] ~ [7▲] buttons to

turn the pages.

When the amount of available ﬁles or

folders exceeds ten, the bottom of the

display changes as shown below.

Press Next

Press Prev.(previous)

Select the ﬁle/folder.

There are two ways to select the ﬁle/

folder:

• Press the [A] - [J] button.

Press the letter button

corresponding to the ﬁle/folder you

wish to call up. (In the example

display shown above, the voice ﬁles

are shown.)

• Use the [DATA ENTRY] dial and

the [ENTER] button.

When you turn the [DATA ENTRY]

dial, the highlight moves among the

available ﬁles/folders. Highlight the

desired ﬁle or folder (voice ﬁles are

shown in the example above) and

press the [ENTER] button to call up

the selected item.

Double-clicking the

appropriate [A] -[J] button

calls up the corresponding

ﬁle and returns to the MAIN

display.

Highlighting the desired ﬁle

and double-clicking the

[ENTER] button calls up the

corresponding ﬁle and

returns to the MAIN display.

Press the [EXIT] button to go back to the MAIN display.

You can go back to the previous display by pressing the [EXIT] button.

When “JAPANESE” is

selected for the Language

parameter (pages 50, 143),

and you change this to one of

the western languages, the

kanji and kana characters of

the ﬁle name stored in the disk

drive are changed to western

characters. In the opposite

case, special Latin characters

and marks are changed into

normal characters. Also, in the

case of ﬂoppy disk data, text

in the ﬁles are changed to

characters that cannot be

read by the instrument.

Keep in mind that similar prob-

lems may occur when trying to

access ﬁles originating or

edited by a computer having a

different language operating

system. In general, be careful

when switching languages —

you risk not being able to

access the data properly.

Exiting from small pop-up windows

You can also exit from small pop-up

windows (such as in the illustration

below) by pressing the [EXIT] button.

Basic Operations — Organizing Your Data

CVP-205/203

Naming Files/Folders

You can assign names to ﬁles and folders. Any ﬁle/folder in the USER and FLOPPY DISK sections can be named or

renamed. Execute the following steps when there is data in the User drive. If there are Preset ﬁles/folders you wish to

rename, copy them beforehand (page 44) and use them as User ﬁles/folders.

File/Folder-related Operations

END

Press the [1▼] (NAME) button (page 39).

The NAME display appears.

Select the appropriate ﬁle/folder and press the [7▼](OK) button.

The currently selected ﬁle/folder is highlighted. To select another ﬁle/folder, press one of the

[A] - [J] buttons.

A ﬁle/folder name can con-

tain up to 50 half size letters

(or 25 Hiragana and kanji let-

ters), including the Icon ID

(see the note below) and the

extension.

The ﬁle name will appear on

your computer as follows. If

you change the Icon ID or

the extension, the icon may

change or the ﬁle may not be

properly recognized.

ABCDE.S002.MID

File ID Icon ID

Extension

Input the new name (page 46).

Press the [8▲] (OK) button. To cancel,

press the [8▼] (CANCEL) button.

Basic Operations — Organizing Your Data

CVP-205/203

Moving Files/Folders

You can move ﬁles and folders as desired, for organizing your data. Any ﬁle/folder in the USER and FLOPPY DISK

sections can be moved, using the cut-and-paste operation described below.

END

Press the [2▼] (CUT) button (page 39).

The CUT display appears.

Select the desired ﬁle/folder for moving.

Select the appropriate ﬁle/folder and press the [7▼](OK) button.

The currently selected ﬁle/folder is highlighted. To select another ﬁle/folder, press one of the [A] -

[J] buttons.

Several ﬁles/folders can be selected together, even those from other pages. To release or cancel

the selection, press the button of the selected ﬁle/folder again.

Press the [6▼] (ALL) button to select all the ﬁles/folders in the displayed page (USER/FLOPPY

DISK). When the [6▼] (ALL) button is pressed the [6▼] button changes to “ALL OFF” button to

release or cancel the selection.

Press the [7▼] (OK) button.

To stop the operation, press the [8▼] (CANCEL) button.

This operation cannot be

used to directly move a ﬁle/

folder from one ﬂoppy disk to

another. If you want to do

this, cut and paste the ﬁle or

folder from the ﬁrst ﬂoppy

disk to the USER page, then

change disks and paste it to

the FLOPPY DISK page.

All ﬁles/folders in a ﬂoppy

disk can be copied to

another disk in one batch

(page 142).

Call up the destination display.

Only the USER and FLOPPY DISK pages can be selected as the destination.

Press the [4▼] (PASTE) button.

The ﬁle/folder you cut is now pasted at the destination.

After being pasted, the ﬁles

are automatically re-ordered

in alphabetical order and

displayed.

About ﬁles/folders in a

ﬂoppy disk

In the FLOPPY DISK page

of the Open/Save display,

only the ﬁles which can be

handled in that Open/Save

display will appear — even

though a folder in a ﬂoppy

disk can contain different

kinds of ﬁles.

In the case of a folder cut-

and-paste operation (for

ﬂoppy disk), an entire folder

can be cut; however, only the

speciﬁc ﬁles which can be

handled in the current Open/

Save display will be pasted.

Basic Operations — Organizing Your Data

CVP-205/203

Copying Files/Folders

You can also copy ﬁles and folders as desired, for organizing your data. Any ﬁle/folder in the PRESET, USER and

FLOPPY DISK sections can be copied, using the copy-and-paste operation described below.

Deleting Files/Folders

You can also delete ﬁles and folders as desired, for organizing your data. Any ﬁle/folder in the USER and FLOPPY DISK

sections can be deleted, using the operation described below.

END

Press the [3▼] (COPY) button

(page 39).

The COPY display appears.

Select the desired ﬁle/folder.

Select the appropriate ﬁle/folder

and press the [7▼](OK) button.

The currently selected ﬁle/folder is

highlighted. To select another ﬁle/

folder, press one of the [A] - [J]

buttons.

Several ﬁles/folders can be

selected together, even those from

other pages. To release or cancel

the selection, press the button of

the selected ﬁle/folder again.

Press the [6▼] (ALL) button to

select all the ﬁles/folders in the

displayed page (PRESET/USER/

FLOPPY DISK). When the [6▼]

(ALL) button is pressed, the [6▼]

button changes to “ALL OFF,”

letting you release or cancel the

selection.

Press the [7▼] (OK) button.

To stop the operation, press the [8▼]

(CANCEL) button.

This operation cannot be

used to directly copy a ﬁle/

folder from one ﬂoppy disk to

another. If you want to do

this, copy and paste the ﬁle

or folder from the ﬁrst ﬂoppy

disk to the User page, then

change disks and paste it to

the Floppy Disk page.

Call up the destination display.

Only the USER and FLOPPY DISK pages can

be selected as the destination.

Press the [4▼] (PASTE) button.

The ﬁle/folder you copied is now pasted at the destination.

Please note that the copy

functions are intended for

your personal use only.

END

Press the [5▼] (DELETE) button (page 39).

The DELETE display appears.

Select the desired ﬁle/folder.

Select the appropriate ﬁle/folder and press the [7▼](OK)

button.

The currently selected ﬁle/folder is highlighted. To select

another ﬁle/folder, press one of the [A] - [J] buttons.

Several ﬁles/folders can be selected together, even

those from other pages. To release or cancel the

selection, press the button of the selected ﬁle/folder

again.

Press the [6▼] (ALL) button to select all the ﬁles/folders

in the displayed page (USER/FLOPPY DISK). When the

[6▼] (ALL) button is pressed, the [6▼] button changes

to “ALL OFF,” letting you release or cancel the selection.

Press the [7▼] (OK) button.

To cancel the operation, press the [8▼] (CANCEL)

button.

The message “Are you sure you want to delete the

“******” ﬁle (or data/folder)? YES/NO” appears.

YES ..........Deletes the highlighted item.

NO............Exits from the prompt without deleting.

When several ﬁles have been selected, the message

“Are you sure you want to delete the “******” ﬁle (or

data/folder)? YES/YES ALL/NO/CANCEL” appears.

YES/NO...... Deletes the highlighted item (YES), or

skips the highlighted item without deleting

(NO).

YES ALL .... Deletes all selected items at once.

CANCEL .... Exits from the prompt without deleting.

Basic Operations — Organizing Your Data

CVP-205/203

Saving Files

This operation lets you save the data (such as song and voice) you created in current

memory (page 40) to ﬁles. The ﬁles can be saved only to the USER and FLOPPY DISK

drives.

If the Open/Save display for the type of data you wish to save is not shown, ﬁrst return to

the MAIN display by pressing the [DIRECT ACCESS] button followed by the [EXIT] button.

Then, press the appropriate button [A]–[J] from the MAIN display to call up the respective

Open/Save display. Finally, call up the USER or FLOPPY DISK page (pages 39, 40).

Organizing Files by Creating a New Folder

This operation lets you easily organize your various ﬁles into categories by creating a new

folder for each category. Folders can only be created in the USER and FLOPPY DISK

sections.

Displaying Upper Level pages

Press the [8▼] (UP) button to call up the upper level pages. For example, you can call up the folder level pages from

the ﬁle level pages.

Entering Characters and Changing Icons

The internal memory capac-

ity of the Clavinova is about

580KB. Memory capacity for

2DD and 2HD ﬂoppy disks is

about 720KB and 1.44MB,

respectively. When you store

data to these locations, all

ﬁle types of the Clavinova

(Voice, Style, Song, Regis-

tration, etc.) are stored

together.

The ﬁles of commercially

available DOC software and

Yamaha Disklavier software,

and their edited ﬁles on the

CVP-205/203, can be stored

in the USER page, but can-

not be copied to another

ﬂoppy disk.

Folder directories can con-

tain up to four levels.

The maximum total number

of ﬁles and folders which can

be stored is 800, but this

may differ depending on the

length of the ﬁle names.

The maximum number of

ﬁles which can be stored in a

folder will be 250.

Enter a name for the new ﬁle (page 46).

Press the [8▲] (OK) button.

To stop the operation, press the [8▼] (CANCEL) button.

Press the [6▼]

(SAVE) button.

Enter the name of the new folder (page 46).

Press the [8▲](OK) button.

To cancel the operation, press the [8▼] (CANCEL) button.

Call up the page to

which you wish to

create a new folder

and press the [7▼]

(NEW) button

(page 39).

If you select Japanese as the Language in the

FUNCTION display (page 143), the following

different types of characters and sizes can be

entered:

(kana-kan)

Hiragana and kanji, marks (full size)

(kana)

Katakana (normal size), marks (full size)

(kana)

Katakana (half size), marks (half size)

A B C — Alphabet (capital and small letters, full size), numbers (full size), marks (full size)

ABC — Alphabet (capital and small letters, half size), numbers (half size), marks (half size)

If you’ve selected a language other than Japanese in the FUNCTION display (page 143), the

following types of characters are available:

CASE — Alphabet (capital letters, half size), numbers (half size), marks (half size)

case — Alphabet (lowercase letters, half size), numbers (half size), marks (half size)

Change the type of character by using the [1▲] button.

Call up the ICON SELECT display by pressing

the [1▼] button. This lets you change the icon

at the left of the ﬁle name.

Press the [1▼]

(NAME), [6▼]

(SAVE), or [7▼]

(NEW) button

(page 39).

Basic Operations — Organizing Your Data

CVP-205/203

Entering Characters

The instructions that follow show you how to enter characters in naming your ﬁles and folders. The method is much the

same as inputting names and numbers to your cell phone.

Move the cursor to the desired position by using the [DATA ENTRY] dial.

Press the appropriate button, [2▲] - [7▲] and [2▼]- [6▼], corresponding to the character you wish to enter.

Several different characters are assigned to each button, and the characters change each time you press the button.

To actually enter the selected character, move the cursor or press another letter-input button.

If you’ve entered a character by mistake, move the cursor to the character letter you wish to erase and press the

[7▼] (DELETE) button. If you want to delete all of the characters on the line at once, press and hold down the

[7▼] (DELETE) button for a while, or press the [8▼] (CANCEL) button. When the cursor appears in reverse display

(highlight), only the reversed area is deleted.

To actually enter the new name, press the [8▲] (OK) button.

To cancel the operation, press the [8▼] (CANCEL) button.

■ Converting into Kanji (Japanese language)

This applies only if you are using the “ (kana-kan)” button (in Japanese). When

the input “hiragana” characters are shown in reverse display (highlighted), press the

[ENTER] button one or several times to convert the characters into the appropriate

kanji. The reversed area can be changed by the [DATA ENTRY] dial. The converted

area can be changed back to “hiragana” by the [7▼] (DELETE) button. The reversed

area can be cleared at once by the [8▼] (CANCEL) button. To actually enter the

change, press the [8▲] (OK) button or enter the next character. To enter the

“hiragana” itself (without converting it), press the [8▲] (OK) button.

■ Entering special character marks (umlaut, accent, Japanese “ ” and “ ”)

Select a character to which a character mark is to be added and press the [6▼] button

(before actual entry of the character.)

■ Entering miscellaneous characters (marks)

You can call up the mark list by pressing the [6▼] button, after actually entering a

character by moving the cursor.

Move the cursor to the desired mark by using the [DATA ENTRY] dial, then press the

▲] (OK) or [ENTER] button.

■ Entering numbers

First, select one of the following: “A B C” (full-size alphabet), “ABC” “CASE” (half-size

capital alphabet) and “case” (half-size lowercase alphabet). Then, press and hold

down the appropriate button, [2

▲] - [7▲] and [2▼] - [5▼], for a while, or press it

repeatedly until the desired number is selected.

The following half-size

marks cannot be used in

naming ﬁles and folders:

¥ \ / : * ? “ < > |

In the case of characters

which are not accompanied

by special character marks

(with the exception of kana-

kan and half-size katakana),

you can call up the mark list

by pressing the [6▼] button

after selecting a character

(before actual entry of a

character).

Basic Operations — Organizing Your Data

CVP-205/203

Changing the Icon

You can also change the icon that

appears at the left of the ﬁle name.

Call up the ICON SELECT display by

pressing the [1▼] (ICON) button from

the character input display (page 46).

Select the desired icon by using the

[A] - [J] buttons, or by using the

[3▲▼] - [5▲▼] buttons, then enter

the selected icon by pressing the [8▲]

(OK) button.

This convenient control lets you easily select items in the display or quickly change parameter values. The actual

function of the [DATA ENTRY] dial differs depending on the selected display.

■ Adjusting values

You can change parameter values by

rotating the [DATA ENTRY] dial. In the

example [BALANCE] display, turning

the dial adjusts the volume of the part

in reverse display (highlight). To adjust

the volume of another part, ﬁrst select

the part by pressing the [

▲▼] button

corresponding to the part, then rotate

the [DATA ENTRY] dial.

■ Selecting items

You can select the desired item or

function in the display by rotating the

[DATA ENTRY] dial. The selected item

can then be called up or executed by

using the [ENTER] button.

In the example VOICE display, you

can select the desired voice ﬁle with

the [DATA ENTRY] dial, and call up

the selected item by pressing the

[ENTER] button on the panel.

BACK NEXT

Cancels the icon selection operation.

Turns pages

for icon

selection.

Enters the selected icon.

Using the [DATA ENTRY] Dial

DATA

ENTRY

ENTER

DATA

ENTRY

Basic Operations — Organizing Your Data

CVP-205/203

With the convenient Direct Access function, you can instantly call up the desired display — with just a single additional

button press. Press the [DIRECT ACCESS] button and a message appears in the display prompting you to press the

appropriate button. Then, simply press the button corresponding to the desired setting display to instantly call up that

display. In the example below, Direct Access is used to call up the display for selecting the Chord Fingering (page 131).

Refer to the Direct Access Chart (page 49) for a list of the displays that can be called up

with the Direct Access function.

Direct Access — Instant Selection of Displays

MIN

STYLE

ACMP

MAX

AUTO FILLIN

POWER

OFF

MASTER VOLUME

FADE IN / OUT

METRONOME

START STOP

OTS LINK

BREAK

INTRO

SONG

EXTRA TRACKS

(STYLE)

TRACK 2

(L)

TRACK 1

(R)

REC TOP START / STOP REW FF REPEAT GUIDE

NEW SONG

TEMPO

SYNC.START

RESET

MAIN

TAP TEMPO

TRANSPOSE

RESET

ENDING / rit. SYNC.STOP SYNC.START START / STOP

ABCD

DIRECT ACCESS

DEMO

HELP

FUNCTION

DIGITAL

STUDIO

SOUND

CREATOR

DIGITAL

RECORDING

MIXING

CONSOLE

BALANCE

PAR T

CHANNEL

ON / OFF

12345678

EXIT

BACK NEXT

VOICE PART

ON / OFF

LAYER

LEFT

LCD

CONTRAST

ENTER

DATA

ENTRY

VOICE EFFECT

REVERB

VOICE

PIANO & HARPSI.

BRASS

MUSIC FINDER

PIANO

DSP VARIATION HARMONY / ECHO MONO LEFT HOLD

E.PIANO ORGAN & ACCORDION PERCUSSION GUITAR BASS

WOODWIND

STRINGS CHOIR & PAD SYNTH. XG USER

ONE TOUCH SETTING

REGISTRATION MEMORY

FREEZE

MEMORY

12345678

1234

DIRECT ACCESS

ACMP

DIRECT ACCESS

Here’s a convenient way to

return to the MAIN display

from any other display:

Simply press the [DIRECT

ACCESS] button, then the

[EXIT] button.

Basic Operations — Organizing Your Data

CVP-205/203

Direct Access Chart

Operation: [DIRECT ACCESS] button + button listed below Corresponding LCD display and function

See pages

STYLE [ACMP] FUNCTION CHORD FINGERING FINGERING TYPE selection 131

[BREAK]

MIXING CONSOLE (STYLE

PART )

VOLUME/VOICE

VOICE settings

120[INTRO] PANPOT settings

MAIN [A] VOLUME settings

MAIN [B]

FILTER

HARMONIC CONTENT settings

121

MAIN [C] BRIGHTNESS settings

MAIN [D]

EFFECT

REVERB settings

122[ENDING] CHORUS settings

[AUTO FILL IN] DSP settings

[OTS LINK]

FUNCTION

STYLE SETTING/SPLIT

POINT

130

[SYNC. STOP] SYNC. STOP WINDOW setting

[SYNC. START] —

[START/STOP] —

SONG [TRACK1]

FUNCTION SONG SETTING

TRACK1 CHANNEL selection

129

[TRACK2] TRACK2 CHANNEL selection

[EXTRA TRACKS]

[REPEAT]

[GUIDE] GUIDE MODE selection

[REC] —

[TOP] —

[START/STOP] —

[REW] —

[FF] —

METRONOME [START/STOP]

FUNCTION

UTILITY

METRONOME settings

140[FADE IN/OUT] FADE IN/OUT settings

TEMPO [TAP TEMPO] TAP settings

[]

MIDI MIDI CLOCK setting 138

[]

TRANSPOSE [ ] CONTROLLER

TRANSPOSE settings

133

[] MIXING CONSOLE TUNE 121

MENU [DEMO]

FUNCTION

UTILITY

LANGUAGE selection 143

[HELP] LCD BRIGHTNESS settings 141

[FUNCTION] MIDI MIDI settings 137

DIGITAL STUDIO [SOUND CREATOR]

MASTER TUNE/SCALE

TUNE

MASTER TUNING setting

127

[DIGITAL RECORDING] SCALE TUNING setting

[MIXING CONSOLE] —

[BALANCE]

MIXING CONSOLE (SONG

PART )

VOLUME/VOICE

VOLUME settings

120

[CHANNEL ON/OFF] VOICE settings

[DIRECT ACCESS] Exit from the Direct Access mode

[NEXT] —

[BACK] —

[ENTER] —

[EXIT] Return to the MAIN display

VOICE PART [LAYER]

MIXING CONSOLE

TUNE OCTAVE settings 121

[LEFT]

VOICE EFFECT [REVERB]

EFFECT

REVERB settings

122[DSP] DSP settings

[VARIATION] EFFECT TYPE selection

[HARMONY/ECHO] FUNCTION HARMONY/ECHO 135

[MONO] MIXING CONSOLE TUNE PORTAMENTO TIME settings 121

[LEFT HOLD]

FUNCTION

STYLE SETTING/SPLIT POINT

SPLIT POINT (LEFT) setting 130

VOICE [PIANO & HARPSI]

VOICE SET 135

[E.PIANO]

[ORGAN & ACCORDION]

[PERCUSSION]

[GUITAR]

[BASS]

[BRASS]

[WOODWIND]

[STRINGS]

[CHOIR & PAD]

[SYNTH.]

[XG]

[USER]

[MUSIC FINDER] MUSIC FINDER MUSIC FINDER SEARCH1 (Searching the records) 71

ONE TOUCH SETTING [1] —

[2] —

[3] —

[4] —

[PIANO]

FUNCTION

CONTROLLER

KEYBOARD TOUCH selection

133

REGISTRATION MEMORY [FREEZE] FREEZE 134

[1]

REGISTRATION BANK REGISTRATION EDIT (Editing the REGISTRATION) 86

[2]

[3]

[4]

[5]

[6]

[7]

[8]

[MEMORY]

FUNCTION

REGISTRATION SEQUENCE (Creating the REGISTRATION SEQUENCE) 134

PEDAL RIGHT

CONTROLLER

RIGHT PEDAL function assignment

131

CENTER CENTER PEDAL function assignment

LEFT LEFT PEDAL function assignment

AUX AUX PEDAL function assignment

Basic Operations — Organizing Your Data

CVP-205/203

The Help messages give you explanations and descriptions of all the main functions and features of the CVP-205/203.

Help Messages

MIN

STYLE

ACMP

MAX

AUTO FILLIN

POWER

OFF

MASTER VOLUME

FADE IN / OUT

METRONOME

START STOP

OTS LINK

BREAK

INTRO

SONG

EXTRA TRACKS

(STYLE)

TRACK 2

(L)

TRACK 1

(R)

REC TOP START / STOP REW FF REPEAT GUIDE

NEW SONG

TEMPO

SYNC.START

RESET

MAIN

TAP TEMPO

TRANSPOSE

RESET

ENDING / rit. SYNC.STOP SYNC.START START / STOP

ABCD

DIRECT ACCESS

DEMO

HELP

FUNCTION

DIGITAL

STUDIO

SOUND

CREATOR

DIGITAL

RECORDING

MIXING

CONSOLE

BALANCE

PART

CHANNEL

ON / OFF

12345678

EXIT

BACK NEXT

VOICE PART

ON / OFF

LAYER

LEFT

LCD

CONTRAST

ENTER

DATA

ENTRY

VOICE EFFECT

REVERB

VOICE

PIANO & HARPSI.

BRASS

MUSIC FINDER

PIANO

DSP VARIATION HARMONY / ECHO MONO LEFT HOLD

E.PIANO ORGAN & ACCORDION PERCUSSION GUITAR BASS

WOODWIND

STRINGS CHOIR & PAD SYNTH. XG USER

ONE TOUCH SETTING

REGISTRATION MEMORY

FREEZE

MEMORY

12345678

1234

HELP

ENTER

DATA

ENTRY

BACK NEXT

EXIT

DEMO

HELP

FUNCTION

2-1 Select the desired

Help topic.

2-2 Call up the topic.

Select the Language, if necessary. The language

selected here are also used for various “Messages”

shown during operations.

Help messages can be displayed in

any one of the following languages:

ENGLISH

JAPANESE

GERMAN

FRENCH

SPANISH

ITALIAN

Use this to select

different pages.

Help messages also feature links to the detailed explanation or actual

setting display of the selected topic. Simply select the underlined word

(using the [DATA ENTRY] dial), and press the [ENTER] button to jump to

the detailed explanation or actual setting display of the selected topic.

Press this to return

to the previous

display.

END

The language can also be selected

in the FUNCTION “LANGUAGE”

(page 143) display.

When “JAPANESE” is selected for

the Language parameter, and you

change this to one of the western

languages, the kanji and kana char-

acters of the ﬁle name stored in the

disk drive are changed to western

characters. In the opposite case,

special Latin characters and marks

are changed into normal characters.

Also, in the case of ﬂoppy disk data,

text in the ﬁles are changed to char-

acters that cannot be read by the

instrument.

Keep in mind that similar problems

may occur when trying to access

ﬁles originating or edited by a com-

puter having a different language

operating system. In general, be

careful when switching languages

— you risk not being able to access

the data properly.

Basic Operations — Organizing Your Data

CVP-205/203

The metronome provides a click sound, giving you an accurate tempo guide when you practice, or letting you hear and

check how a speciﬁc tempo sounds.

The metronome starts by pressing the METRONOME [START/STOP]

button. Adjust the tempo by using the TEMPO[ ] [ ] buttons (see below).

To stop the metronome, press the [START/STOP] button again.

This section shows you to adjust the playback tempo — which not only affects the metronome, but also the playback of

a song or an accompaniment style.

Using the Metronome

MIN

STYLE

ACMP

MAX

AUTO FILLIN

POWER

OFF

MASTER VOLUME

FADE IN / OUT

METRONOME

START STOP

OTS LINK

BREAK

INTRO

SONG

EXTRA TRACKS

(STYLE)

TRACK 2

(L)

TRACK 1

(R)

REC TOP START / STOP REW FF REPEAT GUIDE

NEW SONG

TEMPO

SYNC.START

RESET

MAIN

TAP TEMPO

TRANSPOSE

RESET

ENDING / rit. SYNC.STOP SYNC.START START / STOP

ABCD

DIRECT ACCESS

DEMO

HELP

FUNCTION

DIGITAL

STUDIO

SOUND

CREATOR

DIGITAL

RECORDING

MIXING

CONSOLE

BALANCE

PAR T

CHANNEL

ON / OFF

12345678

EXIT

BACK NEXT

VOICE PART

ON / OFF

LAYER

LEFT

LCD

CONTRAST

ENTER

DATA

ENTRY

VOICE EFFECT

REVERB

VOICE

PIANO & HARPSI.

BRASS

MUSIC FINDER

PIANO

DSP VARIATION HARMONY / ECHO MONO LEFT HOLD

E.PIANO ORGAN & ACCORDION PERCUSSION GUITAR BASS

WOODWIND

STRINGS CHOIR & PAD SYNTH. XG USER

ONE TOUCH SETTING

REGISTRATION MEMORY

FREEZE

MEMORY

12345678

1234

METRONOME

START STOP

The sound, volume level,

and the beat (time signature)

of the metronome can all be

changed (page 140).

Adjusting the Tempo

MIN

STYLE

ACMP

MAX

AUTO FILLIN

POWER

OFF

MASTER VOLUME

FADE IN / OUT

METRONOME

START STOP

OTS LINK

BREAK

INTRO

SONG

EXTRA TRACKS

(STYLE)

TRACK 2

(L)

TRACK 1

(R)

REC TOP START / STOP REW FF REPEAT GUIDE

NEW SONG

TEMPO

SYNC.START

RESET

MAIN

TAP TEMPO

TRANSPOSE

RESET

ENDING / rit. SYNC.STOP SYNC.START START / STOP

ABCD

DIRECT ACCESS

DEMO

HELP

FUNCTION

DIGITAL

STUDIO

SOUND

CREATOR

DIGITAL

RECORDING

MIXING

CONSOLE

BALANCE

PART

CHANNEL

ON / OFF

12345678

EXIT

BACK NEXT

VOICE PART

ON / OFF

LAYER

LEFT

LCD

CONTRAST

ENTER

DATA

ENTRY

VOICE EFFECT

REVERB

VOICE

PIANO & HARPSI.

BRASS

MUSIC FINDER

PIANO

DSP VARIATION HARMONY / ECHO MONO LEFT HOLD

E.PIANO ORGAN & ACCORDION PERCUSSION GUITAR BASS

WOODWIND

STRINGS CHOIR & PAD SYNTH. XG USER

ONE TOUCH SETTING

REGISTRATION MEMORY

FREEZE

MEMORY

12345678

1234

TAP TEMPO

TEMPO

RESET

Songs and accompaniment

styles have been given

default (initial) tempo

settings, designed to best

suit the song/style.

TEMPO

RESET

TAP TEMPO

EXIT

Press either the TEMPO [ ]

button or the [] button.

Adjust the tempo by using either the TEMPO [ ]

[] buttons or the [DATA ENTRY] dial.

The number in the display indicates how many

quarter-note beats there are in one minute. The

range is between 5 and 500. The higher the value,

the faster the tempo.

When you change the tempo, both tempos of the

current song and style will be changed to the same

tempo. To restore their respective default (initial)

tempo settings, press both the TEMPO [ ] [ ]

buttons simultaneously. Also refer to the “Tempo

Indications — MAIN display” (page 52) for more

about tempo.

1 2

Press this to

close the

TEMPO display.

END

Basic Operations — Organizing Your Data

CVP-205/203

Tap Tempo

This useful feature lets you tap out the tempo for a song or an accompaniment style.

Simply tap the [TAP TEMPO] button at the desired speed, and the tempo of the song or

the accompaniment style changes to match your tapping.

■ Tempo Indications — MAIN Display

There are three different tempo indications in the Main display, as shown below.

Hitting the [TAP TEMPO]

button produces a tapping

sound. You can change this

sound, if desired (page 141).

You can also use Tap Tempo

to automatically start the

song or accompaniment

style at the desired tempo.

While both the song and

accompaniment style are

stopped, tap the [TAP

TEMPO] button several

times, and the selected

accompaniment style starts

automatically at the tempo

you tapped. While a song is

set to Sync. Start stand-by

(page 61, 75), tapping the

[TAP TEMPO] button starts

the song playback in the

same manner. For songs

and styles in 2/4 and 4/4

time, tap four times; for 3/4

time, tap three times; for 5/4

time, tap ﬁve times.

TEMPO

RESET

TAP TEMPO

Tap the [TAP TEMPO] button twice

to change the tempo.

Playback the song or the

accompaniment style

(page 60, 75).

Indicates the default (initial) tempo

setting for the currently selected

song (unless the tempo has been

changed manually).

Indicates the current tempo for the

selected song, accompaniment

style or the metronome which is

now playing back. When nothing is

playing back (stopped), this

indicates the tempo for the selected

style. When the song and style are

played back simultaneously, the

tempo of the style is automatically

changed to match the tempo of the

song, and is displayed here. This

tempo is used for recording when

recording a song or

accompaniment style.

Indicates the default (initial) tempo

setting for the currently selected

accompaniment style (unless the

tempo has been changed

manually).

CVP-205/203

Reference

Playing the Demos

The CVP-205/203 is an extraordinarily versatile and sophisticated instrument, featuring a wide variety of dynamic

voices and rhythms, plus a wealth of advanced functions. Three different types of Demo songs have been specially

prepared showcasing the stunning sound and features of the CVP-205/203.

MIN

STYLE

ACMP

MAX

AUTO FILLIN

POWER

OFF

MASTER VOLUME

FADE IN / OUT

METRONOME

START STOP

OTS LINK

BREAK

INTRO

SONG

EXTRA TRACKS

(STYLE)

TRACK 2

(L)

TRACK 1

(R)

REC TOP START / STOP REW FF REPEAT GUIDE

NEW SONG

TEMPO

SYNC.START

RESET

MAIN

TAP TEMPO

TRANSPOSE

RESET

ENDING / rit. SYNC.STOP SYNC.START START / STOP

ABCD

DEMO

HELP

FUNCTION

DIGITAL

STUDIO

SOUND

CREATOR

DIGITAL

RECORDING

MIXING

CONSOLE

BALANCE

PAR T

CHANNEL

ON / OFF

BACK NEXT

VOICE PART

ON / OFF

LAYER

LEFT

LCD

CONTRAST

ENTER

DATA

ENTRY

VOICE EFFECT

REVERB

VOICE

PIANO & HARPSI.

BRASS

MUSIC FINDER

PIANO

DSP VARIATION HARMONY / ECHO MONO LEFT HOLD

E.PIANO ORGAN & ACCORDION PERCUSSION GUITAR BASS

WOODWIND

STRINGS CHOIR & PAD SYNTH. XG USER

ONE TOUCH SETTING

REGISTRATION MEMORY

FREEZE

MEMORY

12345678

1234

DEMO

HELP

FUNCTION

BACK NEXT

DEMO

HELP

FUNCTION

2-3 Press one of these buttons twice

— once to select the desired

demo, and once again to start it.

2-2 Use these to select

different display pages.

Press this to play back all Demo songs/items continuously, starting from

the ﬁrst item at the top left of the display. This is available only from the

FUNCTION page.

All of the available demos are played back in sequence, starting from the one

at top left. The VOICE and STYLE pages do not have the [AUTO] button;

however, all demo songs are played back in sequence.

Pressing this button cancels the interactive features of the Function Demos

(otherwise available in step 3 below).

2-1 Use the [BACK][NEXT] buttons to select the desired Demo category.

Function Demos ....... These demonstrate each of the different functions on the CVP-205/203.

Voice Demos ............. These showcase the voices of the CVP-205/203.

Style Demos .............. These introduce you to the rhythms and accompaniment styles of the CVP-205/203.

Pressing the [DEMO]

button automatically

plays back the Demo

songs at random.

Playing the Demos

CVP-205/203

EXIT

Relevant explanations are shown in the display.

END

Return to the MAIN screen.

BACK NEXT

VOICE PART

ON / OFF

LAYER

LEFT

ENTER

DATA

ENTRY

This example shows the Voices in the

FUNCTION demo.

For the Function demos, an introduction screen appears in the display and

the Demo starts playing.

Select the desired word or item by using the [DATA ENTRY] dial, then press

the [ENTER] button or number buttons ([1▼], [2▼], etc.) to call it up.

Use the [BACK][NEXT]

buttons in the introduction

screen to call up the previ-

ous or next page.

Press the SONG [START/

STOP] button to stop the

Demo song. To start the

Demo again from the point

at which it was stopped,

press the SONG [START/

STOP] button again.

Rewind and fast-forward

can also be used with the

Demo songs (page

77).

CVP-205/203

Voices

The CVP-205/203 gives you an enormous selection of authentic voices, including various keyboard instruments, strings

and brass — and many, many more.

MIN

STYLE

ACMP

MAX

AUTO FILLIN

POWER

OFF

MASTER VOLUME

FADE IN / OUT

METRONOME

START STOP

OTS LINK

BREAK

INTRO

SONG

EXTRA TRACKS

(STYLE)

TRACK 2

(L)

TRACK 1

(R)

REC TOP START / STOP REW FF REPEAT GUIDE

NEW SONG

TEMPO

SYNC.START

RESET

MAIN

TAP TEMPO

TRANSPOSE

RESET

ENDING / rit. SYNC.STOP SYNC.START START / STOP

ABCD

DIRECT ACCESS

DEMO

HELP

FUNCTION

DIGITAL

STUDIO

SOUND

CREATOR

DIGITAL

RECORDING

MIXING

CONSOLE

BALANCE

PAR T

CHANNEL

ON / OFF

12345678

EXIT

BACK NEXT

VOICE PART

ON / OFF

LAYER

LEFT

LCD

CONTRAST

ENTER

DATA

ENTRY

VOICE EFFECT

REVERB

VOICE

PIANO & HARPSI.

BRASS

MUSIC FINDER

PIANO

DSP VARIATION HARMONY / ECHO MONO LEFT HOLD

E.PI ANO ORGAN & ACCORDION PERCUSSION GUITAR BASS

WOODWIND

STRINGS CHOIR & PAD SYNTH. XG USER

ONE TOUCH SETTING

REGISTRATION MEMORY

FREEZE

MEMORY

12345678

1234

VOICE

PIANO & HARPSI.

BRASS

E.PIANO ORGAN & ACCORDION PERCUSSION GUITAR BASS

WOODWIND

STRINGS CHOIR & PAD SYNTH. XG USER

Selecting a Voice

VOICE

PIANO & HARPSI.

BRASS

E.PIANO ORGAN & ACCORDION PERCUSSION GUITAR BASS

WOODWIND

STRINGS CHOIR & PAD SYNTH. XG USER

BACK NEXT

END

EXIT

Select

the

desired

voice

group.

2-3 Select the voice.

2-1 Select the memory location of the

voice (PRESET/USER/FLOPPY DISK).

Press this to start the

demo of the selected

voice. To stop the demo

at any time, press this

button again.

Press this to call up the display for selecting the voice group.

Indicates that the display

is for selecting the MAIN

voice (page 25).

2-2 Select the

various pages

in the current

voice group.

Play the keyboard to hear the

selected

voice.

Press this to return to

the MAIN display.

When you select a voice

group, the last selected

voice will automatically be

selected.

Selecting a voice automati-

cally selects the best-suited

effect and other settings for

that particular voice. You can

disable this so that settings

are not automatically

selected (page 135).

You can set how much the

volume of the voice changes

according to your playing

strength (page 133).

For a list of the available

voices, refer to the separate

Data List.

You can set whether the

voice bank and program

change numbers (“MSB-

LSB-Program Change num-

ber” at the right above the

voice name) are displayed or

not (page 141).

XG is a major enhancement

of the GM System level 1 for-

mat, and was developed by

Yamaha specially to provide

more voices and variations,

as well as greater expressive

control over voices and

effects, and to ensure com-

patibility of data well into the

future.

Voices

CVP-205/203

One-touch Piano Play

This convenient, easy-to-use feature completely and automatically reconﬁgures the entire CVP-205/203 for optimum

piano performance. No matter what settings you’ve made from the panel, you can instantly call up the piano settings by

a single button press.

PIANO button

This reconﬁgures all of the panel settings for playing the CVP-205/203 as a

piano.

Voice Characteristics

The voice type and its deﬁning characteristics are indicated above the voice name.

Natural!

These rich and luscious voices are comprised mostly of keyboard instrument sounds and are especially intended

for playing piano and other keyboard parts. Since they use a completely independent sound source, you can play

full, sustained chords — even along with the accompaniment style — and not have to worry about notes cutting

off. They also take full advantage of Yamaha’s advanced sampling technology such as Stereo Sampling, Dynamic

Sampling, Sustain Sampling, and Key-off Sampling.

Live!

These acoustic instrument sounds were sampled in stereo, to produce a truly authentic, rich sound — full of

atmosphere and ambience.

Cool!

These voices capture the dynamic textures and subtle nuances of electric instruments — thanks to a huge amount

of memory and some very sophisticated programming.

Sweet!

These acoustic instrument sounds also beneﬁt from Yamaha’s sophisticated technology — and feature a sound so

ﬁnely detailed and natural, you’ll swear you’re playing the real thing!

Drum

Various drum and percussion sounds are assigned to individual keys, letting you play the sounds from the

keyboard.

SFX

Various special effect sounds are assigned to individual keys, letting you play the sounds from the keyboard.

Keyboard Percussion

When one of the drum of SFX kits is selected in the PERCUSSION voice group, various drum, percussion, and

special effect sounds are assigned to individual keys, letting you play the sounds from the keyboard. The various

drums and percussion instruments of the Standard Kit are indicated by symbols above the assigned keys. Keep in

mind that even though different kits feature different sounds, some same-named sounds in different kits are

identical.

Refer to the separate Data List (Drum/key Assignment List) for a listing of the sounds in each drum/SFX kit.

Piano Lock function

The convenient Piano Lock function lets you “lock” the piano so that you don’t

inadvertently change the settings by pressing another button on the panel. Once

locked, the CVP-205/203 stays in the piano mode, even if other buttons are pressed

— preventing you from accidently starting a song or accompaniment style during a

piano concert.

Hold down the [PIANO] button for a short time, until a message appears prompting

you to enable Piano Lock.

To enable Piano Lock, select “OK.”

To turn Piano Lock off, hold down the [PIANO] button again for a short time.

You can also use the metro-

nome with this function

(page 51).

PIANO

Even if you turn Piano Lock

off, the piano settings are

still active.

Voices

CVP-205/203

The CVP-205/203 lets you set three voices for simultaneous play: MAIN, LAYER, and LEFT. By effectively combining

these three, you can create richly textured, multi-instrument setups for your performance.

Playing a layer of two voices

Playing two voices separately — on the left

and right sections of the keyboard

Playing three different voices — one on the

left section of the keyboard, plus a layer of

two on the right

Layer — Layering Two Different Voices

Layer/Left — Playing Several Sounds Simultaneously

MIN

STYLE

ACMP

MAX

AUTO FILLIN

POWER

OFF

MASTER VOLUME

FADE IN / OUT

METRONOME

START STOP

OTS LINK

BREAK

INTRO

SONG

EXTRA TRACKS

(STYLE)

TRACK 2

(L)

TRACK 1

(R)

REC TOP START / STOP REW FF REPEAT GUIDE

NEW SONG

TEMPO

SYNC.START

RESET

MAIN

TAP TEMPO

TRANSPOSE

RESET

ENDING / rit. SYNC.STOP SYNC.START START / STOP

ABCD

DIRECT ACCESS

DEMO

HELP

FUNCTION

DIGITAL

STUDIO

SOUND

CREATOR

DIGITAL

RECORDING

MIXING

CONSOLE

BALANCE

PART

CHANNEL

ON / OFF

12345678

EXIT

BACK NEXT

VOICE PART

ON / OFF

LAYER

LEFT

LCD

CONTRAST

ENTER

DATA

ENTRY

VOICE EFFECT

REVERB

VOICE

PIANO & HARPSI.

BRASS

MUSIC FINDER

PIANO

DSP VARIATION HARMO NY / ECHO MONO LEFT HOLD

E.PI ANO ORGAN & ACCORDION PERCUSSION GUITAR BASS

WOODWIND

STRINGS CHOIR & PAD SYNTH. XG USER

ONE TOUCH SETTING

REGISTRATION MEMORY

FREEZE

MEMORY

12345678

1234

VOICE PART

ON / OFF

LAYER

LEFT

LAYER part

MAIN part

LEFT part

MAIN part

Split point

Left range Right range

LEFT part

MAIN part

Split point

LAYER part

Left range Right range

VOICE PART

ON / OFF

LAYER

LEFT

EXIT

END

Press this to

turn the LAYER

function on. To

turn it off, press

the button again.

There is an alternate way for

quickly selecting both the

MAIN and LAYER voices

from the panel: While hold-

ing down one panel voice

button, press a second

voice button. The ﬁrst

selected voice becomes the

MAIN voice, and the second

becomes the LAYER.

Select LAYER with the [G] button. Press the same

button to call up the VOICE display, from which you

can select the speciﬁc voice you want to play in a

layer with the Main voice. The method of selecting a

voice here is the same as that in VOICE (MAIN)

display (page 55).

Press this to return to the

MAIN display.

Voices

CVP-205/203

Left — Setting Separate Voices for the Left and Right Sections of the Keyboard

This section of the panel lets you add a variety of effects to the voices you play on the keyboard.

■ REVERB

Reverb is an effect that recreates the acoustic ambiance of a performance space — anything from a small jazz club to a

concert hall.

■ DSP

The CVP-205/203 features a variety of dynamic built-in digital effects, letting you process

the sound in various ways. You can use DSP to enhance the voices in subtle ways — such

as by applying chorus to add animation and depth, or using a symphonic effect to give

the sound warmth and richness. DSP also has effects such as distortion that can

completely change the character of the sound. DSP is set for the currently selected part

(MAIN/LAYER/LEFT).

■ VARIATION (Regular voice only; page 89)

This control changes the Variation effect settings, letting you alter some aspect of the effect, depending on the selected

type. For example, when the Rotary Speaker effect is selected (page 122), this lets you switch the rotor speed between

slow and fast.

Set the LEFT to

ON. Press this

button again to

set it to OFF.

LAYER

LEFT

Select LEFT with the [H] button. Press the same

button to call up the VOICE display, from which you

can select the speciﬁc voice you want to play in a

left. How to select the voice is the same as the way of

VOICE (MAIN) screen (page 55).

The split point can be freely

set to any key on the key-

board. To set it, call up the

SPLIT POINT display by

pressing the [I] (SPLIT

POINT) button in the MAIN

display. The operation steps

are the same as in the

STYLE SETTING/SPLIT

POINT display of the FUNC-

TION page (page 130).

Each part (MAIN, LAYER,

and LEFT) can have its own

volume setting (page 62).

You can also use the LAYER

and LEFT functions

together, to create a combi-

nation layer/split. To do this,

set separate voices for the

left and right sections of the

keyboard (as indicated), and

set up a layer of two different

voices on the right.

EXIT

END

Press this to

return to the

MAIN display.

Applying Voice Effects

MIN

STYLE

ACMP

MAX

AUTO FILLIN

POWER

OFF

MASTER VOLUME

FADE IN / OUT

METRONOME

START STOP

OTS LINK

BREAK

INTRO

SONG

EXTRA TRACKS

(STYLE)

TRACK 2

(L)

TRACK 1

(R)

REC TOP START / STOP REW FF REPEAT GUIDE

NEW SONG

TEMPO

SYNC.START

RESET

MAIN

TAP TEMPO

TRANSPOSE

RESET

ENDING / rit. SYNC.STOP SYNC.START START / STOP

ABCD

DIRECT ACCESS

DEMO

HELP

FUNCTION

DIGITAL

STUDIO

SOUND

CREATOR

DIGITAL

RECORDING

MIXING

CONSOLE

BALANCE

PAR T

CHANNEL

ON / OFF

12345678

EXIT

BACK NEXT

VOICE PART

ON / OFF

LAYER

LEFT

LCD

CONTRAST

ENTER

DATA

ENTRY

VOICE EFFECT

REVERB

VOICE

PIANO & HARPSI.

BRASS

MUSIC FINDER

PIANO

DSP VARIATION HARMONY / ECHO MONO LEFT HOLD

E.PI ANO ORGAN & ACCORDION PERCUSSION GUITAR BASS

WOODWIND

STRINGS CHOIR & PAD SYNTH. XG USER

ONE TOUCH SETTING

REGISTRATION MEMORY

FREEZE

MEMORY

12345678

1234

VOICE EFFECT

REVERB DSP VARIATION HARMONY / ECHO MONO LEFT HOLD

Press one of the effect buttons to turn the corresponding effects on. Press it again to turn the effect off.

For explanations on each of the effects, see below.

The DSP and VARIATION

effect types and the their

depth can be selected and

adjusted in the MIXING CON-

SOLE display (page 122).

Voices

CVP-205/203

■ HARMONY/ECHO

This control adds Harmony or Echo effects to the voices played on the right hand section

of the keyboard (page 135).

■ MONO

This control determines whether the voice is played monophonically (only one note at a

time) or polyphonically for each part (MAIN/LAYER/LEFT). This is set to MONO when the

lamp is lit, and set to polyphonic when the lamp is off. When set to MONO, only the last

note played will sound. This lets you play wind instrument voices more realistically.

Depending on the selected voice, the MONO setting also lets you effectively use the

Portamento effect, when playing in legato.

■ LEFT HOLD

This function causes the left part voice to be held even when the keys are released — the

same effect as when the damper (sustain) pedal is pressed. This function is especially

effective when used with the auto accompaniment. For example, if you play and release a

chord in the auto accompaniment section of the keyboard (with the left part on and the

Left voice set to Strings), the strings part sustains, adding a natural richness to the overall

accompaniment sound.

■ Damper Pedal (Right)

■ Sostenuto Pedal (Center)

■ Left Pedal

When the Piano voice is selected, pressing this pedal reduces the volume and slightly

changes the timbre of the notes you play.

The settings assigned to this pedal may differ depending on the selected voice.

■ Foot Controller/Footswitch

An optional Yamaha foot controller (FC7) or footswitch (FC4 or FC5) can be connected to

the AUX PEDAL jack and used to control various functions assigned in the FUNCTION page (page 131).

You can add special empha-

sis to melody lines you play

over chords by using the

Layer function with a mono-

phonic voice. Set the Main

voice to play polyphonically

and set the Layer voice to

play monophonically

(MONO). In this case, the

melody you play — including

the top notes of any chords

— sounds monophonically.

Try this using the following

voices.

MAIN voice

: Brass Section

(polyphonic) +

LAYER voice

Sweet Trump (monophonic)

The Portamento effect creates

a smooth pitch glide between

successively played notes.

Using the Pedals

You can also assign one of

many other functions to

these pedals (as well as the

optional foot controller or

footswitch). For example, you

can use it to start/stop the

accompaniment style, or use

it to play Fill-ins (page 131).

Damper Pedal

Sostenuto Pedal

Left Pedal

The CVP-205/203 features three pedals.

• Some voices may sound

continuously or have a

long decay after the notes

have been released while

the damper pedal is held.

• Certain voices in the [PER-

CUSSION] and [XG]

groups may not be affected

by use of the damper pedal.

When you press the damper pedal

here, the notes you play before you

release the pedal have a longer sustain.

The damper pedal performs the same function as the

damper pedal on an actual acoustic piano, letting you

sustain the sound of the voices even after releasing the

keys.

• Certain voices, such as

[STRINGS] or [BRASS],

sustain continuously when

the sostenuto pedal is

pressed.

• Certain voices in the

[PERCUSSION] and [XG]

groups may not be

affected by use of the sos-

tenuto pedal.

When you press the sostenuto pedal

here while holding the note, the note will

sustain as long as you hold the pedal.

If you play a note or chord on the keyboard and press the

sostenuto pedal while the note(s) are held, those notes will

be sustained as long as the pedal is held, but all

subsequently played notes will not be sustained.

The depth of the left pedal

effect can be adjusted

(

page 131

CVP-205/203

Styles

The CVP-205/203 features styles (accompaniment patterns) in a variety of different musical genres including pops, jazz,

Latin and dance. To use it, all you have to do is play the chords with your left hand as you perform and the selected

Accompaniment Style (style) matching your music will automatically play along, instantly following the chords you

play. Try selecting some of the different styles (refer to separate Data List (Style List) ) and play them.

MIN

STYLE

ACMP

MAX

AUTO FILLIN

POWER

OFF

MASTER VOLUME

FADE IN / OUT

METRONOME

START STOP

OTS LINK

BREAK

INTRO

SONG

EXTRA TRACKS

(STYLE)

TRACK 2

(L)

TRACK 1

(R)

REC TOP START / STOP REW FF REPEAT GUIDE

NEW SONG

TEMPO

SYNC.START

RESET

MAIN

TAP TEMPO

TRANSPOSE

RESET

ENDING / rit. SYNC.STOP SYNC.START START / STOP

ABCD

DIRECT ACCESS

DEMO

HELP

FUNCTION

DIGITAL

STUDIO

SOUND

CREATOR

DIGITAL

RECORDING

MIXING

CONSOLE

BALANCE

PAR T

CHANNEL

ON / OFF

12345678

EXIT

BACK NEXT

VOICE PART

ON / OFF

LAYER

LEFT

LCD

CONTRAST

ENTER

DATA

ENTRY

VOICE EFFECT

REVERB

VOICE

PIANO & HARPSI.

BRASS

MUSIC FINDER

PIANO

DSP VARIATION HARMONY / ECHO MONO LEFT HOLD

E.PI ANO ORGAN & ACCORDION PERCUSSION GUITAR BASS

WOODWIND

STRINGS CHOIR & PAD SYNTH. XG USER

ONE TOUCH SETTING

REGISTRATION MEMORY

FREEZE

MEMORY

12345678

1234

STYLE

ACMP

AUTO FILLIN

OTS LINK

BREAK

INTRO

MAIN

ENDING / rit. SYNC.STOP SYNC.START START / STOP

ABCD

Playing a style

BACK NEXT

To call up the [MAIN] dis-

play, ﬁrst press the

[DIRECT ACCESS] button,

then press the [EXIT] but-

ton.

2-2 Select a Style.

2-1 Select a location (Preset,

User, Floppy Disk) for

saving the style.

When you've opened a lower directory's display,

this button (UP) lets you call up the next higher

directory, from which you can select Style groups.

For a list of the available

accompaniment styles, refer

to the separate Data List

(Style List).

Styles

CVP-205/203

STYLE

ACMP

SYNC.STOP SYNC.START START / STOP

STYLE

ACMP

AUTO FILLIN

OTS LINK

BREAK

INTRO

MAIN

ENDING / rit. SYNC.STOP SYNC.START START / STOP

ABCD

STYLE

ACMP

AUTO FILLIN

OTS LINK

BREAK

INTRO

MAIN

ENDING / rit.

ABCD

SYNC.STOP SYNC.START START / STOP

Auto Accompaniment section

Split point

END

When the [ACMP] button is set to on, you can play/indicate chords from the auto

accompaniment section of the keyboard. (Depending on the settings, this may be

the range of the Left voice, or the entire keyboard.)

Turn SYNC. (SYNCHRONIZED) START on.

The Tempo can be adjusted

using the TEMPO [ ][ ] or

[TAP TEMPO] button.

If you tap the [TAP TEMPO]

button, the tempo will adjust to

the same speed that you tapped.

You can set the key range

for auto accompaniment

(page 130).

• You can begin the rhythm

channels (tracks) of the

Style by pressing the

[START/STOP] button.

• The rhythm channels of

the style can also be

started by tapping the

[TAP TEMPO] button.

With the style stopped,

tap the [TAP TEMPO]

button three, four or ﬁve

times (three for 3/4 time,

four for 2/4 or 4/4 time,

ﬁve for 5/4 time).

Stop the style.

When you simultaneously

play back accompaniment

styles with a song, the

accompaniment parts

recorded to the song (chan-

nels 9 - 16) are temporarily

replaced by the selected

accompaniment style — let-

ting you try out and use dif-

ferent accompaniment with

the song (page 76).

Turn ACMP off.

Sync. Start

Enabling this lets you start

the style simply by playing

the keyboard.

As soon as you play a chord with the auto accompaniment section, the style starts.

For details about chord ﬁngerings, refer to page 63.

Accompaniment Style Characteristics

The deﬁning characteristics of some of the accompaniment styles are indicated above the relevant style names in the Open/Save display.

Session!

These styles provide even greater realism and authentic backing by mixing in original chord types and changes, as well as special riffs with

chord changes, with the Main sections. These have been programmed to add “spice” and a professional touch to your performances of

certain songs and in certain genres. As a result, the styles may not necessarily be appropriate — or even harmonically correct — for all

songs and for all chord playing. In some cases for example, playing a simple major triad may result in a seventh chord, or playing an on-

bass chord may result in incorrect or unexpected accompaniment.

Piano Combo!

These accompaniment styles feature a basic piano trio (piano, bass, and drums), augmented in some cases with other instruments. Since

this is a small combo sound, the accompaniment backing is appropriately sparse, making it useful and effective for a wide variety of songs.

Pianist!

These special styles provide piano-only accompaniment — effectively recreating the left-hand performance of an accomplished pianist.

Just by playing the proper chords with your left hand, you can automatically add complicated arpeggios and bass/chord patterns — such

as difﬁcult-to-play stride piano parts.

Styles

CVP-205/203

Playing a Style’s Rhythm Channels only

Adjusting the Volume Balance/Channel Muting

STYLE

ACMP

AUTO FILLIN

OTS LINK

BREAK

INTRO

MAIN

ENDING / rit. SYNC.STOP SYNC.START START / STOP

ABCD

Rhythm starts.

Select a style (page 60).

The Rhythm channels are

part of the styles. Each style

has different rhythm pat-

terns.

Set to off.

Play along with the rhythm playback.

The Tempo can be adjusted using the TEMPO [ ][ ] or [TAP TEMPO] buttons.

If you tap the [TAP TEMPO] button, the tempo will adjust to the same speed that

you tapped.

When selecting the style

group “PIANIST,” the

rhythm doesn’t sound.

When you want to use any

of the styles, always make

sure that ACMP is turned

on.

Press the STYLE [START/STOP] button

again to stop the rhythm playback.

END

You can also start the

rhythm simply by playing a

key on the keyboard, if Sync

Start is enabled (turn on the

[SYNC.START] button).

BALANCE

PA RT

CHANNEL

ON / OFF

BALANCE display

Adjust the output level of the Part.

Parts played from the

keyboard (MAIN/LAYER/

LEFT)

STYLE part (Auto

Accompaniment section)

SONG part

MIC part

CHANNEL ON/OFF display

Call up the STYLE display by pressing the [CHANNEL ON/OFF]

button, then turn the instrument you want to cancel off. To listen to

only one instrument by itself, hold down the appropriate button for

the channel to set the channel to SOLO. To cancel SOLO, simply

press the appropriate channel button again.

Channel

Refers to the MIDI channel

in the song data (page 150).

The channels are assigned

as shown below.

Song

1 - 16

Accompaniment Style

9 - 16

Call up the

BALANCE

display.

Call up the

Channel ON/

OFF display.

Styles

CVP-205/203

The style playback can be controlled by the chords you play in the keys to the left of the split point. There are 7 types of

ﬁngerings as described below. Go to the CHORD FINGERING page (page 131), and select the Chord Fingerings. The

page shows how to play chords with your left hand.

SINGLE FINGER

Single Finger accompaniment makes it simple to produce beautifully orchestrated accompaniment using major,

seventh, minor and minor-seventh chords by pressing a minimum number of keys on the auto accompaniment section

of the keyboard. The abbreviated chord ﬁngerings described below are used.

MULTI FINGER

The Multi Finger mode automatically detects Single Finger or Fingered chord ﬁngerings,

so you can use either type of ﬁngering without having to switch ﬁngering modes. If you

want to play minor, seventh, or minor-seventh chords using the SINGLE FINGER

operation in the MULTI FINGER Mode, always press the closest white/black key(s) to the

root of the chord.

FINGERED

This mode lets you produce accompaniment by playing full chords on the auto

accompaniment section of the keyboard. The Fingered mode recognizes the various

chord types listed on the next page.

FINGERED ON BASS

This mode accepts the same ﬁngerings as the FINGERED mode, but the lowest note

played in the auto accompaniment section of the keyboard is used as the bass note,

allowing you to play “on bass” chords. For example, to indicate a C-on-E chord, play a C

major chord with E as the lowest note (E, G, C).

FULL KEYBOARD

This method detects chords in the entire key range. Chords are detected in a way similar

to Fingered, even if you split the notes between your left and right hands — for example,

playing a bass note with your left hand and a chord with your right, or by playing a chord

with your left hand and a melody note with your right.

AI FINGERED

This mode is basically the same as FINGERED, with the exception that less than three

notes can be played to indicate the chords (based on the previously played chord, etc.).

AI FULL KEYBOARD

When this advanced auto accompaniment mode is engaged, the CVP-205/203 will

automatically create appropriate accompaniment while you play just about anything,

anywhere on the keyboard using both hands. You don’t have to worry about specifying the accompaniment chords.

Although the AI Full Keyboard mode is designed to work with many songs, some arrangements may not be suitable for

use with this feature.

This mode is similarto FULL KEYBOARD, with the exception that less than three notes can be played to indicate the

chords (based on the previously played chord, etc.). 9

and 11

chords cannot be played.

Chord Fingerings

For a major chord, press the root key only. For a minor chord, simultaneously press the root key

and a black key to its left.

For a seventh chord, simultaneously press the root

key and a white key to its left.

For a minor-seventh chord, simultaneously press the

root key and both a white and black key to its left.

Chord detection in the AI

Full Keyboard mode occurs

at approximately 8th-note

intervals. Extremely short

chords — less than an 8th

note in length — may not be

detected.

In Full Keyboard mode,

chords are detected based

on the lowest and second

lowest notes you play. If the

two lowest notes fall within a

single octave, those two

notes determine the chord. If

the lowest note and the sec-

ond lowest note are sepa-

rated by more than one

octave, the lowest note

becomes the bass and the

chord is determined from the

second lowest note and the

other notes played in the

same octave.

Artiﬁcial Intelligence

Styles

CVP-205/203

* Only this voicing (inversion) is recognized. Other chords not marked with an asterisk can be played in any inversion.

Chord Name [Abbreviation] Normal Voicing

Display for root “C”

Major [M] 1 - 3 - 5 C

Ninth [9] 1 - 2 - 3 - 5 C9

Sixth [6] 1 - (3) - 5 - 6 C6

Sixth ninth [6

] 1 - 2 - 3 - (5) - 6 or 3 - 6 - 2* C6

Major seventh [M7] 1 - 3 - (5) - 7 CM7

Major seventh ninth [M7

] 1 - 2 - 3 - (5)j - 7 CM7

Major seventh add sharp eleventh [M7

]

1 - (2) - 3 - 4 - 5 - 7 or 1 - 2 - 3 - 4 - (5) - 7

CM7

Flatted ﬁfth [ 5] 1 - 3 - 5 C 5

Major seventh ﬂatted ﬁfth [M7

] 1 - 3 - 5 - 7 CM7

Suspended fourth [sus4] 1 - 4 - 5 Csus4

Augmented [aug] 1 - 3 - 5 Caug

Major seventh augmented [M7aug] 1 - (3) - 5 - 7 CM7aug

Minor [m] 1 - 3 - 5 Cm

Minor ninth [m9] 1 - 2 - 3 - 5 Cm9

Minor sixth [m6] 1 - 3 - 5 - 6 Cm6

Minor seventh [m7] 1 - 3 - (5) - 7 Cm7

Minor seventh ninth [m7

] 1 - 2 - 3 - (5) - 7 or 3 - 7 - 2 Cm7

Minor seventh eleventh [m7

] 1 - (2) - 3 - 4 - 5 - ( 7) Cm7

Minor major seventh [mM7] 1 - 3 - (5) - 7 CmM7

Minor major seventh ninth [mM7

] 1 - 2 - 3 - (5) - 7 CmM7

Minor seventh ﬂatted ﬁfth [m7

] 1 - 3 - 5 - 7 Cm7 5

Minor major seventh ﬂatted ﬁfth [mM7

] 1 - 3 - 5 - 7 CmM7

Diminished [dim] 1 - 3 - 5 Cdim

Diminished seventh [dim7] 1 - 3 - 5 - 6 Cdim7

Seventh [7] 1 - 3 - (5) - 7 or 1 - (3) - 5 - 7 C7

Seventh ﬂatted ninth [7

] 1 - 2 - 3 - (5) - 7 C7

Seventh add ﬂatted thirteenth [7

] 1 - 3 - 5 - 6 - 7 C7

Seventh ninth [7

] 1 - 2 - 3 - (5) - 7 or 3 - 7 - 2* C7

Seventh add sharp eleventh [7

]

1 - (2) - 3 - 4 - 5 - 7 or 1 - 2 - 3 - 4 - (5) - 7

Seventh add thirteenth [7

] 1 - 3 - (5) - 6 - 7 or 3 - 6 - 7 C7

Seventh sharp ninth [7

] 1 - 2 - 3 - (5) - 7 C7

Seventh ﬂatted ﬁfth [7

] 1 - 3 - 5 - 7 C7

Seventh augmented [7aug] 1 - 3 - 5 - 7 C7aug

Seventh suspended fourth [7sus4] 1 - 4 - 5 - 7 C7sus4

Suspended second [sus2] 1 - 2 - 5 Csus2

Chord Types Recognized in the Fingered Mode (Example for “C” chords)

( )

CM7

( )

Caug

Cm6

Cm7

( )

Cm7



CmM7



Cm7

( )

Cm9

CmM7

( )

CmM7

( )

Cdim

Cdim7

( )



( )



Csus4



( )

CM7



( )

CM7



( )



( )

C7aug

Cm7

( )

CM7aug

( )

C7sus4 Csus2

• Notes in parentheses can

be omitted.

• For FINGERED, FIN-

GERED ON BASS, and AI

FINGERED, if you play

any three adjacent keys

(including black keys), the

chord sound will be can-

celed and only the rhythm

instruments will continue

playing (Chord Cancel

function). This let you play

back only the rhythm.

• Playing two same root

keys in the adjacent

octaves produces accom-

paniment based only on

the root.

• A perfect ﬁfth (1 + 5) pro-

duces accompaniment

based on the root and the

ﬁfth.

• The auto accompaniment

Style will sometimes not

change when related

chords are played in

sequence (e.g. some

minor chords followed by

the minor seventh).

• You can also have the

CVP-205/203 “teach” you

how to play Fingered

chords. From the CHORD

FINGERING display

(page 131), specify the

chord you want to learn,

and the notes you should

press are indicated in the

display.

 



 













 

 





 





















 





Styles

CVP-205/203

The CVP-205/203 features various types of Auto Accompaniment Sections that allow you

to vary the arrangement of the Style. They are: Intro, Main, Break and Ending. By

switching among them as you play, you can easily produce the dynamic elements of a

professional-sounding arrangement in your performance.

Arranging the Style Pattern

(SECTIONS: MAIN A/B/C/D, INTRO, ENDING, BREAK)

You can also use this func-

tion to play only rhythms

(page 62).

STYLE

ACMP

AUTO FILLIN

OTS LINK

BREAK

INTRO

MAIN

ENDING / rit. SYNC.STOP SYNC.START START / STOP

ABCD

Auto Accompaniment section

Split point

STYLE

ACMP

AUTO FILLIN

OTS LINK

BREAK

INTRO

MAIN

ENDING / rit.

ABCD

SYNC.STOP SYNC.START START / STOP

Select a style (page 60).

2-1 Turn the ACMP function on.

2-2 Press the [INTRO] button. To cancel the INTRO section

before starting the style, press the [INTRO] button again.

2-3 Turn the SYNC. START function on.

The Intro section starts as soon as you play a key in the Auto

Accompaniment section of the keyboard, and changes to the Main section.

Press this button to add breaks.

• If you press the [INTRO]

button, you can play back

an Intro section while an

accompaniment is play-

ing.

• You can dynamically con-

trol the level of the

accompaniment by how

softly or strongly you play

the keys in the Auto

Accompaniment section

of the keyboard

(page 130).

• If you press the [SYNC.

START] button while an

accompaniment is play-

ing, the accompaniment

will stop and the CVP-

205/203 will enter Syn-

chronized Start standby

status.

• You can also change

style sections by using

the pedal (page 131).

• The Break section lets

you add dynamic varia-

tions and breaks in the

rhythm of the accompani-

ment, to make your per-

formance sound even

more professional. If you

press the [BREAK] but-

ton while an accompani-

ment is playing, the ﬁll-in

will play back for one

measure.

• The indicator of the desti-

nation section (MAIN A/

B/C/D) will ﬂash while the

Break is playing.

• When the [AUTO FILLIN]

button is set to on and

the MAIN [A][B][C][D]

button is pressed after

the ﬁnal half beat (eighth

note) of the measure, the

ﬁll-in will begin from the

next measure.

• Section button indications

— [BREAK], [INTRO],

[MAIN], [ENDING] but-

tons

LED is green

— The section is not

selected.

LED is red

— The section is cur-

rently selected.

LED is off

— No section data; the

section cannot be

played.

Main sections can be shifted.

Styles

CVP-205/203

Stopping the Style Playback While Releasing Keys (SYNC. STOP)

When the Synchro Stop function is engaged, accompaniment playback will stop

completely when all keys in the Auto Accompaniment section of the keyboard are released.

Accompaniment playback will start again as soon as the key in the Auto Accompaniment

section is played.

Fade-in/Fade-out

The accompaniment style also include a convenient Fade-in/Fade-out function that

gradually fades in and fades out the accompaniment. To start the style with a fade-in,

press the [FADE IN/OUT] button, then turn SYNC. START on. To cancel the fade-in

before starting the style, press the button again.

To fade out and stop the Style, press this button while the style is playing. The time of the

fade-in/fade-out can also be set (page 140).

• Styles can also be started

by pressing the STYLE

[START/STOP] button.

• You can select the Intro

and Ending type by press-

ing the [E] button in the

MAIN window (page 67).

• If you press the [INTRO]

button while the ending is

playing, the Intro section

will begin playing after the

ending is ﬁnished.

• When the [AUTO FILLIN]

button is set to on and you

press a MAIN button while

the ending is playing, ﬁll-in

accompaniment will

immediately start playing,

continuing with the Main

section.

• You can begin the accom-

paniment by using the

Ending instead of the Intro

section. In this case, the

auto accompaniment

doesn’t stop when the

ending is ﬁnished.

• If you select a different

style while the style is not

playing, the “default”

tempo for that style is also

selected. If the accompa-

niment is playing, the

same tempo is maintained

even if you select a differ-

ent style.

• When STOP ACMP is set

to on and the accompani-

ment is not playing, you

can play both chords and

bass in the Auto Accom-

paniment section in the

keyboard (page 130).

STYLE

ACMP

AUTO FILLIN

OTS LINK

BREAK

INTRO

MAIN

ENDING / rit.

ABCD

SYNC.STOP SYNC.START START / STOP

END

This switches to the ending section. When the ending is ﬁnished, the Style stops

automatically. You can have the ending gradually slow down (ritardando) by

pressing the same [ENDING/rit.] button again while the ending is playing back.

Auto Accompaniment section

Split point

Turn ACMP (Accompaniment) on.

STYLE

ACMP

AUTO FILLIN

OTS LINK

BREAK

INTRO

MAIN

ENDING / rit. SYNC.STOP SYNC.START START / STOP

ABCD

Turn SYNC. STOP on. SYNC. START is also automatically set to on when

SYNC. STOP is turned on.

As soon as you play a chord with your left hand, the auto accompaniment

starts.

You can also use the SYNC.

STOP function by pressing

the auto accompaniment

section/left-hand range

brieﬂy (page 130).

The auto accompaniment stops when you release your left hand from the keys.

Playing a chord with your

left hand automatically

restarts the auto

accompaniment.

Press the [SYNC. STOP]/

[SYNC. START] button

again to stop the

accompaniment.

Synchro Stop cannot be set

to on when the ﬁngering

mode is set to Full Key-

board/AI Keyboard or the

auto accompaniment on the

panel is set to off.

END

Styles

CVP-205/203

Selecting Intro and Ending Types (INTRO/ENDING)

Playing Fill-in patterns automatically when

changing accompaniment sections — Auto Fill In

Select a Intro

Select a Ending

Play the style using

the Intro or Ending

section (page 30, 31).

To call up the [MAIN] dis-

play, ﬁrst press the [DIRECT

ACCESS] button, then press

the [EXIT] button.

Fill

A short phrase used to add

variation to the style.

STYLE

ACMP

AUTO FILLIN

OTS LINK

BREAK

INTRO

MAIN

ENDING / rit.

ABCD

SYNC.STOP SYNC.START START / STOP

Play the style and switch among the accompaniment sections as they play

(page 30, 31).

Fill-in patterns play automatically between each change in the Main

sections.

You can also add a ﬁll-in by

pressing the selected MAIN

button again.

To cancel the Auto Fill, press the [AUTO FILLIN] button again.

You can temporarily disable

Auto Fill In during a perfor-

mance by pressing the next

Main section’s button twice

quickly.

END

Styles

CVP-205/203

The convenient One Touch Setting function makes it easy for you to select voices and effects that are appropriate to the style

you’re playing. Each preset style has four pre-programmed panel setups that you can select by pressing a single button.

Appropriate Panel Setting for the Selected Style

(ONE TOUCH SETTING)

MIN

STYLE

ACMP

MAX

AUTO FILLIN

POWER

OFF

MASTER VOLUME

FADE IN / OUT

METRONOME

START STOP

OTS LINK

BREAK

INTRO

SONG

EXTRA TRACKS

(STYLE)

TRACK 2

(L)

TRACK 1

(R)

REC TOP START / STOP REW FF REPEAT GUIDE

NEW SONG

TEMPO

SYNC.START

RESET

MAIN

TAP TEMPO

TRANSPOSE

RESET

ENDING / rit. SYNC.STOP SYNC.START START / STOP

ABCD

DIRECT ACCESS

DEMO

HELP

FUNCTION

DIGITAL

STUDIO

SOUND

CREATOR

DIGITAL

RECORDING

MIXING

CONSOLE

BALANCE

PAR T

CHANNEL

ON / OFF

12345678

EXIT

BACK NEXT

VOICE PART

ON / OFF

LAYER

LEFT

LCD

CONTRAST

ENTER

DATA

ENTRY

VOICE EFFECT

REVERB

VOICE

PIANO & HARPSI.

BRASS

MUSIC FINDER

PIANO

DSP VARIATION HARMONY / ECHO MONO LEFT HOLD

E.PI ANO ORGAN & ACCORDION PERCUSSION GUITAR BASS

WOODWIND

STRINGS CHOIR & PAD SYNTH. XG USER

ONE TOUCH SETTING

REGISTRATION MEMORY

FREEZE

MEMORY

12345678

1234

ONE TOUCH SETTING

1234

STYLE

ACMP

AUTO FILLIN

OTS LINK

BREAK

INTRO

MAIN

ENDING / rit.

ABCD

SYNC.STOP SYNC.START START / STOP

ONE TOUCH SETTING

1234

Select a style (page 60).

Press one of the ONE TOUCH SETTING buttons ([1] - [4]).

ONE TOUCH SETTING

1234

LED is green — The One Touch

Setting is not selected.

LED is off — No One Touch

Setting data. The button is not

available.

LED is red — The One Touch Setting is currently selected.

As soon as you play a

chord with your left

hand, the auto

accompaniment starts.

Auto Accompaniment section

Split point

Stop the Auto Accompaniment.

Try out other One Touch Setting setups. You can also create your own One

Touch Setting setups (page 69).

Various settings (such as voices, effects, etc.) that match the selected

style can be instantly recalled. When the style is not playing, Auto

Accompaniment and Sync. Start will automatically be turned on.

For details about the One Touch Setting parameters, refer to the

separate Data List (Parameter Chart).

Styles

CVP-205/203

Automatically Changing One Touch Settings with the Sections — OTS Link

The convenient OTS (One Touch Setting) Link function lets you automatically have One Touch Settings change when

you select a different Main section (A - D).

Registering the Panel Controls in One Touch Setting (ONE TOUCH SETTING)

This section covers how to create your own One Touch Setting setups (four setups per style). For a list of One Touch

Setting setup parameters, refer to the separate Data List (Parameter Chart).

AUTO FILLIN

OTS LINK

When you switch among the Main sections (A

- D), the corresponding One Touch Setting will

be called up automatically.

The Main sections A, B, C, and D correspond

to One Touch Settings 1, 2, 3, and 4,

respectively.

The One Touch Settings

can be set to change with

the sections in one of two

different timings (page 130):

• Immediately when you

press a section button.

• At the next measure (in

an accompaniment

style), after you press a

section button.

To cancel the OTS Link function, press the [OTS LINK] button again.

END

MEMORY

ONE TOUCH SETTING

1234

Select a style.

Set up the panel controls

such as selecting a voice

as required.

Press the [MEMORY]

button.

END

A message prompting you to save the current style will appear. Select “YES”

to call up the STYLE display, then save the panel settings (page 39, 45).

Unless you store the panel

settings here, the registered

settings will be deleted

when you select a different

accompaniment style.

Press one of the ONE TOUCH SETTING buttons:[1] through [4].

The items you can register in a One Touch Setting are Voice, Harmony and Pedal settings.

Styles

CVP-205/203

The Music Finder feature lets you instantly call up the appropriate settings for the

instrument — including voice, style, and One Touch Settings — simply by selecting the

desired song title. If you want to play a certain song but don’t know which style and voice

settings would be appropriate, the convenient Music Finder function will help you out.

The recommended settings, which together make up a “record,” can also be edited and

stored. This lets you create and save your own Music Finder records for future recall.

Calling Up Ideal Setups for Your Music — Music Finder

The MUSIC FINDER records

and its contents is just one

example of the recom-

mended panel setups. You

can also create your own

Music Finder settings for

your favorite songs and

genres.

Keep in mind that Music

Finder is a performance aid

in that it automatically ﬁnds

appropriate accompaniment

styles and voices for your

playing. Even though you

can specify song titles, it

does not actually contain

song data.

MIN

STYLE

ACMP

MAX

AUTO FILLIN

POWER

OFF

MASTER VOLUME

FADE IN / OUT

METRONOME

START STOP

OTS LINK

BREAK

INTRO

SONG

EXTRA TRACKS

(STYLE)

TRACK 2

(L)

TRACK 1

(R)

REC TOP START / STOP REW FF REPEAT GUIDE

NEW SONG

TEMPO

SYNC.START

RESET

MAIN

TAP TEMPO

TRANSPOSE

RESET

ENDING / rit. SYNC.STOP SYNC.START START / STOP

ABCD

DIRECT ACCESS

DEMO

HELP

FUNCTION

DIGITAL

STUDIO

SOUND

CREATOR

DIGITAL

RECORDING

MIXING

CONSOLE

BALANCE

PAR T

CHANNEL

ON / OFF

12345678

EXIT

BACK NEXT

VOICE PART

ON / OFF

LAYER

LEFT

LCD

CONTRAST

ENTER

DATA

ENTRY

VOICE EFFECT

REVERB

VOICE

PIANO & HARPSI.

BRASS

MUSIC FINDER

PIANO

DSP VARIATION HARMONY / ECHO MONO LEFT HOLD

E.PI ANO ORGAN & ACCORDION PERCUSSION GUITAR BASS

WOODWIND

STRINGS CHOIR & PAD SYNTH. XG USER

ONE TOUCH SETTING

REGISTRATION MEMORY

FREEZE

MEMORY

12345678

1234

MUSIC FINDER

Select a record. For example, select the

top record by pressing the [1▲▼] button

to call up the recommended setups.

The setting data shown here is referred

to as a “record.”

All ..........................Show all records.

FAVORITE..............Show the records that have added to the “Favorite” page.

SEARCH1,2...........Show the results by SEARCH function (page 71).

Sorting the records

MUSIC ...... The record is sorted by song title.

STYLE....... The record is sorted by style name.

BEAT ........ The record is sorted by beat.

TEMPO ..... The record is sorted by tempo.

Change the order of the records

(ascending or descending).

Add the selected record to “Favorite (Bookmark)” page

When you press the [H] button, the “Add selected

data to the favorite list? YES/NO” message will be

displayed. Select [YES] to add the selected page to

“FAVORITE” page.

Search record(s). Enter the condition of the search

in the MUSIC FINDER SEARCH display (page 71).

The results of SEARCH 1 or 2 appear in the

“SEARCH 1” or “SEARCH 2” page respectively.

Call up the MUSIC FINDER RECORD EDIT (page 72) display

(for editing the selected record).

Turn TEMPO LOCK on/off. TEMPO LOCK function lets you avoid changing

the Tempo during style playback when selecting another record. The on/off

setting affects all pages (ALL/FAVORITE/SEARCH 1/SEARCH 2).

Select a record by style name. When sorting the records by style name, press these buttons

to move the cursor to the next /previous style. Simultaneously press the [▲▼] buttons to move

the cursor to the ﬁrst record.

Select a record by song title.

When sorting records by song title,

use the [1▲▼] button to skip up or

down through the songs

alphabetically. Simultaneously

press the [▲▼] buttons to move the

cursor to the ﬁrst record.

Show the

number of

records of

each page.

Play the style (page 61).

Records can be selected by

using the [DATA ENTRY]

dial and pressing the

[ENTER] button.

Styles

CVP-205/203

Searching the Ideal Setups — Music Finder Search

You can search the record by music title or keywords. The results appears in the display.

■ [A] MUSIC

Searches by music or song title. Press this button to call up the display for

inputting the song title.

When you enter the song title (page 46), the search function calls up all

records that contain the entered word or words.

■ [B] KEYWORD

Searches by keyboard. Press this button to call up the display for inputting the

keyword.

When you enter the keyword (page 46), the search function calls up all

records that contain the entered word or words. You can search several

different keywords simultaneously by inserting a separator (comma) between each. The search function ﬁnds and

displays all records that contain at least one match in the keywords.

■ [C] STYLE

Searches by style name. Press this button to call up the STYLE FILE SELECT display. Press

the [A] through [J] button in the display to select the desired accompaniment style. This

convenient function lets you ﬁnd all songs that use a certain accompaniment style.

■ [D] BEAT

Searches by beat or rhythmic feel.

■ [E] SEARCH AREA

Selects a speciﬁc location for searching. You can further narrow down your search by using the SEARCH 1 and 2

selections.

■ [F]~[H] CLEAR

Clears the entered item at left.

■ [1▲▼] TEMPO FROM

You can also narrow your search by specifying a tempo range. This lets you set the minimum tempo for the search. Press

the [▲▼] buttons simultaneously to instantly reset the tempo value to the minimum.

■ [2▲▼]TEMPO TO

You can also narrow your search by specifying a tempo range. This lets you set the maximum tempo for the search.

Press the [▲▼] buttons simultaneously to instantly reset the tempo value to the maximum.

■ [3▲▼]~[5▲▼] GENRE

Selects the speciﬁc music genre for searching. The available range includes all genres (ANY), the preset genres, and any

genres you’ve entered yourself (page 70).

■ [8▼] CANCEL

Press this to cancel the operation and return to the previous display.

Start searching the record.

The results that satisfy all

the conditions appear in the

SEARCH page. For details

about the search settings in

this display, see below.

Press the [I]

(SEARCH 1)

button or [J]

(SEARCH 2)

button in the

MUSIC FINDER

display.

Enter the

conditions for

the search (see

below), then

start search by

using [START

SEARCH] button.

The STYLE FILE SELECT

display can only be used to

select the style name for

searching; it cannot be used

to call up the actual accom-

paniment style.

Styles

CVP-205/203

Editing Records — Music Finder Record Edit

From this display, you can call up existing records and edit them to suit your

preferences. You can even use this to create your own Music Finder records.

■ [A] MUSIC

Selects the music or song title for editing. Press the button to call up the

display for inputting the music or song title, then edit the name as desired.

■ [B] KEYWORD

Selects the keyword for editing. Press the button to call up the display for

inputting the keyword, then edit it as desired.

You can enter several different keywords by inserting a separator (comma)

between each.

■ [C] STYLE

Selects the style name for editing. Always enter the name when a new record is registered.

Press the button to call up the STYLE FILE SELECT display. Press the [A] through [J] button

in the display to select the desired style you want to change/clear/register.

■ [D] BEAT

Selects the beat (time signature) for editing. When another ﬁle is selected by pressing the

[C] button, the current beat setting is replaced with the beat setting of the selected ﬁle.

■ [E] FAVORITE

Adds the selected record to the FAVORITE page (page 70).

■ [F]~[H] CLEAR

Clears the entered item at left.

■ [I] DELETE RECORD

Clears the selected record. The deleted record number becomes empty. When you press this button, a message appears

prompting you to execute, abort or cancel the operation.

YES .................. Press this to clear the record and close the display.

NO .................. Press this to close the display without clearing the record.

CANCEL........... Press this to close the message box and return to the previous display.

You can also change/clear a

preset record. To avoid chang-

ing/clearing the record, register

the record as a new record

after editing.

Press the [8 ▲▼] (RECORD EDIT) button in the MUSIC FINDER display.

Change/clear the record data. You can also register new records. For details

about all settings and operations, see below.

All Music Finder records can be

stored together as a single ﬁle

(page 143). When calling up a

stored ﬁle, a message appears

prompting you to replace or

append the records as desired.

• Replace:

All Music Finder records cur-

rently in the instrument are

deleted and replaced with the

records of the selected ﬁle.

• Append:

The records called up are

added to the vacant record

numbers.

The STYLE FILE SELECT

display can only be used to

select the style name for

record editing; it cannot be

used to call up the actual

accompaniment style.

Keep in mind that the Beat

setting made here is only for

the Music Finder search

function; this does not affect

the actual Beat setting of the

accompaniment style itself.

Styles

CVP-205/203

■ [J] NEW RECORD

Registers a new record. The smallest available empty record number is used for registering.

When you press this button, a message appears prompting you to execute, abort or cancel

the operation.

YES .................. Press this to register the record and close the display.

NO .................. Press this to close the display without registering the record.

CANCEL........... Press this to close the message box and return to the previous display.

■ [1▼▲] TEMPO

Determines the tempo for the selected style. When changing the style with the [C] button, the tempo is automatically

changed to that of the changed style.

■ [3▼▲]~[5▼▲] GENRE

Indicates and changes the genre to which the selected record is assigned. The available range includes all preset genres

as well as any you’ve entered yourself.

■ [6▼▲] GENRE NAME

For entering a genre name. Press the button to call up the display for inputting

the genre name, then edit the name as desired. A maximum of 200 genre

names can be stored.

The genre name you input becomes effective when the current record is edited (overwritten) by pressing the [8▲] (OK)

button, or when a new record is registered by pressing the [J] (NEW RECORD) button.

If you exit from the MUSIC FINDER EDIT display without actually editing or registering a record, the input genre name

is deleted.

■ [8▲] OK

Executes all editing and changes to the record. When you press this button, a message appears prompting you to

execute, abort or cancel the operation.

YES .................. Press this to replace the record and close the display.

NO .................. Press this to close the display without replacing the record.

CANCEL........... Press this to close the message box and return to the previous display.

■ [8▼] CANCEL

Press this to cancel the operation and return to the MUSIC FINDER display.

The maximum number of

records is 2500, including

internal records.

To maintain the edited and registered data, make sure to save all Music Finder records as a ﬁle (page 143). If no saved, the data will

be lost when another Music Finder ﬁle is called up or the factory-programmed settings are restored (page 143).

CVP-205/203

Song Playback

Here you’ll learn how to play back songs. Songs include the internal songs of the instrument, performances you’ve

recorded yourself using the recording functions (page 93), and commercially available song data. You can use this

highly versatile feature in a variety of ways — playing along on the keyboard with the recorded song, as well as

practicing and learning new music with the Guide (page 79) and Repeat (page 78) functions. You can also display the

music notation (CVP-205 only) and lyrics in the LCD.

• Internal songs (Song Book; CVP-205 only)

• Song data on included disk [50 greats for the Piano (CVP-205/203), Music Software

Collection (CVP-203 only)]

• Commercially available song data

Disks having this logo mark feature song data compatible with GM (General

MIDI).

Disks having this logo mark feature song data compatible with Yamaha’s XG

format. XG is a signiﬁcant enhancement of the “GM system level 1” standard,

providing more voices, greater editing control, and support for multiple effect

sections and effect types.

Disks having this logo mark feature song data compatible with Yamaha’s DOC (Disk Orchestra Collection)

format.

Disks having this logo mark feature song data compatible with Yamaha’s original MIDI ﬁle format.

• Songs you recorded (page 93) and stored to the CVP-205/203 or disk.

MIN

STYLE

ACMP

MAX

AUTO FILLIN

POWER

OFF

MASTER VOLUME

FADE IN / OUT

METRONOME

START STOP

OTS LINK

BREAK

INTRO

SONG

EXTRA TRACKS

(STYLE)

TRACK 2

(L)

TRACK 1

(R)

REC TOP START / STOP REW FF REPEAT GUIDE

NEW SONG

TEMPO

SYNC.START

RESET

MAIN

TAP TEMPO

TRANSPOSE

RESET

ENDING / rit. SYNC.STOP SYNC.START START / STOP

ABCD

DIRECT ACCESS

DEMO

HELP

FUNCTION

DIGITAL

STUDIO

SOUND

CREATOR

DIGITAL

RECORDING

MIXING

CONSOLE

BALANCE

PAR T

CHANNEL

ON / OFF

12345678

EXIT

BACK NEXT

VOICE PART

ON / OFF

LAYER

LEFT

LCD

CONTRAST

ENTER

DATA

ENTRY

VOICE EFFECT

REVERB

VOICE

PIANO & HARPSI.

BRASS

MUSIC FINDER

PIANO

DSP VARIATION HARMONY / ECHO MONO LEFT HOLD

E.PIANO ORGAN & ACCORDION PERCUSSION GUITAR BASS

WOODWIND

STRINGS CHOIR & PAD SYNTH. XG USER

ONE TOUCH SETTING

REGISTRATION MEMORY

FREEZE

MEMORY

12345678

1234

SONG

EXTRA TRACKS

(STYLE)

TRACK 2

(L)

TRACK 1

(R)

REC TOP START / STOP REW FF REPEAT GUIDE

NEW SONG

SYNC.START

Compatible Song Types

Commercially available

music data is subject to

intended only for your own

personal use.

For more information on the

song ﬁle types compatible

with the Clavinova, see

page 151.

Song Playback

CVP-205/203

Playing the Internal Songs

Song Playback

BACK

REC TOP START / STOP REW FF REPEAT GUIDE

NEW SONG

SYNC.START

END

2-2 Open a folder and

select a song to be

played back.

2-1 Select the PRESET tab with the [BACK]

button.

You can enable the Synchro

Start for the song by simul-

taneously pressing the

[TOP] button and the

SONG [START/STOP] but-

ton. The song starts as

soon as you play the key-

board. You can also use this

function along with the

Style’s Synchro Start func-

tion (page 61).

You can have the volume

automatically fade in and

fade out at the beginning

and end of the song. Simply

press the [FADEIN/OUT]

button at the start of song

playback to fade in the song,

and press it again at the end

of the song to fade out.

Adjust the tempo by using the TEMPO [ ][ ] buttons

(page 51) or the [TAP TEMPO] button.

You can even change the playback speed by tapping out

the tempo — simply tap the [TAP TEMPO] button twice.

The song starts.

To stop the song immediately, press the

button again.

Press the button in order to go back to the

previous screen.

START / STOP

EXIT

If the MAIN screen (at left) is

not displayed, press the

[DIRECT ACCESS] button

followed by the [EXIT] button.

You can also make a variety

of other settings (such as

tempo, voice selection, set-

tings for the practice func-

tions, etc.) and have them

automatically called up

when you play back the

song (page 105).

Songs can also be played

back continuously. Set

SONG CHAIN PLAY to ON

from the SONG SETTING

display (page 129).

Make sure that the Language

setting for the instrument

(page 143) is the same as that

of the ﬁle name of the song that

you are playing back.

Song Playback

CVP-205/203

Simultaneously Playing a Song and an Accompaniment Style

When playing back a song and an accompaniment style at the same time, channels 9 -

16 of the song data are replaced with accompaniment style channels — allowing you

to use the auto accompaniment styles and features in place of the accompaniment parts

of the song. Make the settings below and play your own chord substitutions in place of

the song’s chord data.

• [ACMP] button .................. ...ON

• [AUTO FILL IN] button ..... ...ON

Select the song and start playback by pressing the SONG [START/STOP] button.

Select the desired accompaniment style.

Start the style by pressing the STYLE [START/STOP] button.

While the song is playing, insert a break or change sections (with the STYLE

section buttons.)

Fill-in patterns play when you switch sections.

The style automatically stops when the song ﬁnishes or is stopped.

The accompaniment stops

when you stop the song. If

the accompaniment style is

playing and you start the

song, the accompaniment

automatically stops. How-

ever, for internal songs that

use accompaniment styles,

the accompaniment style is

not stopped.

END

Some of the internal songs have been created using the accompaniment styles. For these songs, the

accompaniment styles are automatically started when starting song playback.

Song Playback

CVP-205/203

Playing Back Songs on Disk

Insert the disk into the drive.

The method for playing back is the same as in the “Playing the Internal Songs” instructions

(page 75), except that you should select FLOPPY DISK page in the SONG display.

Other Playback-related Operations

■ Repeat / Rewind / Fast forward

■ Adjusting the Volume Balance / Muting Speciﬁc Channels

CHANNEL ON/OFF display

Select the [SONG] tab with the [CHANNEL ON/OFF] button, and mute the desired channel

by setting it to [OFF]. To solo a channel (only that channel will sound), hold down the

appropriate button corresponding to the channel. To release the solo for the channel, press

that channel’s button again.

Before proceeding, make

sure to read the section

“Handling the Floppy Disk

Drive (FDD) and Floppy

Disk” (page 6).

You can set whether or not

the Clavinova automatically

calls up the ﬁrst disk song

when a disk is inserted

(page 142).

Some song data for the

Clavinova has been

recorded with special “free

tempo” settings. During play-

back of such song data, the

measure numbers shown in

the display will not corre-

spond to the actual mea-

sure; this only serves as a

reference as to how much of

the song has been played

back.

Songs containing a large

amount of data may not be

able to be read properly by

the instrument, and as such

you may not be able to

select them. The maximum

capacity is about 200–

300KB, however this may

differ depending on the data

contents of each song.

Insert the disk shutter side

ﬁrst and label face up.

REC TOP START / STOP REW FF REPEAT

NEW SONG

SYNC.START

During playback, you can have the song return to the top and play back again

from the beginning by pressing this button. When playback is stopped,

pressing this button returns the song to the beginning.

Press this button to call up the SONG POSITION display (see

below). To return to the SONG display, press the [EXIT] button.

When “BAR” is selected, you can specify a measure number (counted from the

beginning of the song) by using the [REW] and [FF] buttons.

When “PHRASE MARK” is selected, specify the phrase mark number by using the

[REW] and [FF] buttons.

Phrase Mark

This data speciﬁes a certain

location in the song data. In

the included “Music Soft-

ware Collection” songs

(CVP-203 only), these are

indicated by numbers (1, 2,

etc.) in the score.

SONG POSITION display

“PHRASE MARK” is shown only when the song contains phrase marks. Press the

[J] button to toggle between “BAR” and “PHRASE MARK,” then use the [REW]

and [FF] buttons to select the desired measure or phrase mark.

BALANCE

PA RT

CHANNEL

ON / OFF

Press this button to call up the BALANCE display (page 62).

Press this button to call up the CHANNEL ON/OFF display (see below).

Channel

Refers to the MIDI channel

in the song data. The chan-

nels are assigned as shown

below for the CVP-205/203.

Song

1 - 16

Accompaniment Style

9 - 16

Song Playback

CVP-205/203

This feature lets you mute certain parts of the song (Track1, Track2, Extra Tracks), and play back only those parts you

want to hear. For example, if you want to practice the melody of a song, you can mute just the right-hand part and play

that part yourself.

This feature allows you to specify a certain range of the song (between Point A and Point B), and play it back repeatedly.

Muting Speciﬁc Parts — Track1/Track2/Extra Tracks

SONG

EXTRA TRACKS

(STYLE)

TRACK 2

(L)

TRACK 1

(R)

REC TOP START / STOP REW FF REPEAT GUIDE

NEW SONG

SYNC.START

Select the song to be played back (page 74).

Use this button to turn on/off the right-hand part.

Use this button to turn on/off the left-hand part.

Use this button to turn on/off the additional performance parts

(all but the right hand/left hand).

Start the song.

Adjust the tempo by using the TEMPO [ ][ ] buttons (page 51).

All tracks are automatically

set to on when selecting a

different song.

To stop the song, press the

button again.

START / STOP

END

You can change the channel

assignments for Track 1 and

Track 2 (page 129), letting

you specify which parts are

muted when pressing the

[TRACK 1]/[TRACK 2]/

[EXTRA TRACKS] buttons.

Repeat Playback of a Speciﬁc Range

REC TOP START / STOP REW FF REPEAT

NEW SONG

SYNC.START

START / STOP

Play back the song (page 75, 77).

You can also specify Points

A and B when the song is

stopped. Set Point A by

pressing the [REPEAT] but-

ton, then use the [FF] but-

ton to move to the desired

end location, then set Point

B by pressing the

[REPEAT] button again.

Stop the song.

To cancel the Repeat function, press the

button again.

REPEAT

Press this button at the point you want the

repeating phrase to start (Point A).

Press this button at the point you want the

repeating phrase to end (Point B).

After an automatic lead-in (to help guide you into the phrase), the range from

point A to point B is played back repeatedly.

Regardless of whether the song is playing back or is stopped, pressing the [TOP]

button returns to point A.

Point B cannot be selected

unless Point A has been

selected ﬁrst.

Specifying only Point A

results in repeat playback

between Point A and the

end of the song.

The speciﬁed A and B

points will be erased when

selecting a different song

number, cancelling the

Repeat function, or select-

ing a different repeat mode

— such as Phrase Repeat

or repeat in Song Chain

Play (page 129).

END

Song Playback

CVP-205/203

These fun features make it easy to learn new music. The key guide lamps indicate the notes

you should play, when you should play them, and how long you should hold them down.

Also, when you sing and play along with a song using a connected microphone (CVP-205

only), the Clavinova automatically adjusts the timing of the song to match your vocal

performance.

Practice Functions

For keyboard performance

■ Follow Lights

When this is selected, you can see which notes you should play by watching the key

guide lamps. They light up in time with music, showing you when to play a note. You

can also practice at your own pace — since the accompaniment waits for you to play

the notes correctly.

• Accompaniment Guide

If the song data you’re using contains chord data and the [ACMP] button is turned on,

you can use the guide lamps (page 129) to help you play chords as well. Watch the

guide lamps and try playing the appropriate chords.

■ Any Key

With this function, you can play the melody of a song simply by pressing a single key

(any key is OK) in time with the rhythm. As long as you play the key in time with the

music, the melody ﬂows smoothly with the song.

For sing-along performance

■ Karao-Key

This convenient function lets you control the song and accompaniment playback with just one ﬁnger, while you sing

along. Simply play a key on the keyboard in time with the music — any key is ﬁne — and the accompaniment parts

of the song follow your playing. This lets you control the timing and tempo of the song and accompaniment to

perfectly match your singing performance.

Using the Practice Functions —Guide

You can turn the key guide

lamps on/off from the SONG

SETTING display (page 129).

REC TOP START / STOP REW FF REPEAT GUIDE

NEW SONG

SYNC.START

Key guide lamp

You can also determine the

timing by which the key

guide lamps light to ﬁt your

playing preference (Guide

Lamp Timing; page 129).

If you want to learn how to

play certain chords, use the

Chord Tutor function

(page 131).

The Accompaniment Guide

function cannot be used if

the chord ﬁngering method

is set to Single Finger, Full

keyboard or AI Full Key-

board.

Song Playback

CVP-205/203

Practicing Music with the Guide Functions

Selects the speciﬁc practice function.

Turns the key guide lamps on/off.

Determines the timing by which the

key guide lamps light.

JUST ..... The guide lamp lights in time with the

music, at the same time you should play

the appropriate notes.

NEXT.....The guide lamps light slightly ahead of the

music, indicating the notes you should

play next. The guide lamp ﬂashes if you

do not play the key with the correct timing.

Determines whether phrase mark sections in the song will be repeatedly played

back or not. When this is set to ON, the speciﬁed measures of the phrase play

back repeatedly.

Call up the SONG POSITION display by pressing either the

[REW] button or the [FF] button, and select “PHRASE MARK” by pressing the [J]

button. Set the desired phrase mark number by using the [REW] and [FF] buttons.

Select the desired song (page 75, 77) and mute the track you wish to practice

(page 78).

Select the desired practice function from the SONG SETTING page in the

FUNCTION display (page 129).

To turn the practice function, press the

button again.

GUIDE

END

REC TOP START / STOP REW FF REPEAT GUIDE

NEW SONG

SYNC.START

Start the song and try playing the part you’ve muted.

Adjust the tempo by using the TEMPO [ ][ ] buttons (page 51).

Stop the song.

For details on the SONG SET-

TING display, see page 129.

The guide lamps light

according to song channel

recorded to Tracks 1 and 2

and the chord data in the

song (when such data is

included). Normally, you can

leave the AUTO SET CH

function set to ON, and the

song channel will automati-

cally be set. If the results

aren't satisfactory, you'll

need to match the Channel

Setting “TRK1 CH” and

“TRK2 CH” parameters to

the appropriate right- and

left-hand parts.

Phrase Mark

This data speciﬁes a certain

location in the song data. In

the included “Music Software

Collection” songs (CVP-203

only), these are indicated by

numbers (1, 2, etc.) in the

score.

Track 1 or Tracks 1 & 2 are

automatically selected for

practicing when calling the

practice function — as long

as you haven’t muted the

track to be practiced.

The key guide lamps some-

times light an octave or two

lower/higher than the actual

pitch. Any notes outside of

the 88-key range cannot be

indicated by the key guide

lamps.

If the right- and left-hand

parts recorded to the song

data have not been properly

separated, the practice func-

tions may not work as

expected.

REC TOP START / STOP REW FF REPEAT GUIDE

NEW SONG

SYNC.START

REC TOP START / STOP REW FF REPEAT GUIDE

NEW SONG

SYNC.START

Song Playback

CVP-205/203

With this feature, you can have the notation automatically shown on the display as the song plays. This can be used

with your own recordings as well as the internal Demo songs.

Displaying Music Notation — Score (CVP-205 only)

Select the

desired song

(page 75, 77).

Enables/disables display of the left-hand key range.

Depending on other settings, this parameter may be

unavailable and may appear grayed out. If this is the

case, go to the detailed setting display (shown

below; use the [8▲▼] buttons) and set the LEFT

CH. parameter to any channel except “AUTO.” Or,

go to the SONG SETTING display in the Function

menu (page 129) and set the TRACK 2 parameter

to any channel except “OFF.”

Enables/disables display of the right-hand key range.

Channel 1 is automatically selected when

[TRACK1] is set to [OFF] from the SONG SETTING

display (page 129).

Enables/disables display of the chords.

If the selected song does not contain chord data, chords

are not displayed.

Enables/disables display of the note name (pitch).

Determines the display resolution (or zoom level) of the notation.

SMALL ..... Notation is shown in small size.

LARGE ..... Notation is shown in large size.

The displayed notation is

generated by the Clavinova

based on the song data. As

a result, it may not be

exactly the same as com-

mercially available sheet

music of the same song —

especially when displaying

notation of complicated pas-

sages or many short notes.

Some song data for the

Clavinova has been

recorded with special “free

tempo” settings. For such

song data, the tempo, beat,

measure and music nota-

tion will not be displayed

correctly.

[RIGHT] and [LEFT] cannot

be turned off at the same

time.

The note name is indicated

at the left of the note. When

the space between the

notes is too small, the indi-

cation may be moved to the

top left of the note.

You can increase the num-

ber of measures that will be

displayed by decreasing the

other items to be displayed

(parts, lyrics, chords, etc.).

When accidentals (sharp

and ﬂats) and notes cannot

be displayed on one line,

they are displayed in the

next line from the middle of

the measure.

The notation functions can-

not be used to create song

data by inputting notes. For

information on creating

song data, see page 97.

If the MAIN screen (at left)

is not displayed, press the

[DIRECT ACCESS] button

followed by the [EXIT] but-

ton.

This calls up the detailed setting display for notation.

For details, see the next page.

Enables/disables display of the lyrics.

If the selected song does not contain lyric data, lyrics are

not displayed.

Song Playback

CVP-205/203

Detailed Settings for Notation

■ [1▲▼] LEFT CH/[2▲▼] RIGHT CH

This determines the Left channel (channel for the left-hand part) and Right channel (channel for the right-hand part).

This setting returns to AUTO when a different song is selected.

AUTO .........................The channels for the right- and left-hand parts are assigned automatically — setting the parts

to the same channel as the channel which is speciﬁed in the SONG SETTING display of the

Function menu (page 129).

1-16............................Assigns the part to the speciﬁed channel, 1- 16.

OFF (LEFT CH only)....No channel assignment.

■ [3▲▼], [4▲▼] KEY SIGNATURE

This lets you enter key signature changes in the middle of a song, at the stopped position, allowing you to transpose

key at any point within a song. For a list of the key signatures, with their relative minor keys and accidentals, see the

chart below.

■ [5▲▼] QUANTIZE

This gives you control over the note resolution in the notation, letting you shift or correct

the timing of all displayed notes so that they line up to a particular note value. Make sure

to select the smallest note value which is used in the song.

Note resolution:

1/4 note, 1/8 note, 1/16 note, 1/32 note, 1/4 note triplet, 1/8 note triplet, 1/16 note

triplet, 1/32 note triplet

When “LEFT” and “RIGHT”

are set to the same channel,

the notation of the right-hand

notes and left-hand notes

are displayed in piano format

(two connected staves).

The note indicates the root note of the major key, and the note indicates the root of the relative minor.

C Maj (A min) G Maj (E min) D Maj (B min) A Maj (F

min) E Maj (C

min) B Maj (G

min) F

Maj (D

min) C

Maj (A

min)

Maj (A

min) G

Maj (E

min) D Maj (B

min) A

Maj (F min) E

Maj (C min) B

Maj (G min) F Maj (D min)

Key Signatures and Accidentals

Short notes and ornamented

notes (such as trills and

grace notes) which are

shorter than the Note resolu-

tion will not be displayed in

the notation.

Song Playback

CVP-205/203

■ [6▲▼] NOTE NAME

When [NOTE NAME] is set to ON, the note name and solfeggio name (do, re, mi, etc.) are indicated.

ABC ................. Note names are indicated as letters (C, D, E, F, G, A, B).

Fixed Do.......... Note names are indicated in solfeggio and differ depending on the selected language (page 50).

English.............. Do Re Mi Fa Sol La Ti

French .............. Ut Re Mi Fa Sol La Si

Italian............... Do Re Mi Fa Sol La Si

German............ Do Re Mi Fa Sol La Si

Spanish............. Do re Mi Fa Sol La Si

Japanese...........

Movable Do..... Note names are indicated in solfeggio according to the scale intervals, and as such are relative to

the key. The root note is indicated as Do. For example, in the key of G major the root note of Sol

would be indicated as Do.

As with “Fixed Do,” the indication differs depending on the selected language.

■ [8▲] OK

This closes the detailed setting display and starts generating the notation. You can also

execute this by pressing the [ENTER] button on the panel.

■ [8▼] CANCEL

This closes the detailed setting display without changing the settings. You can also

execute this by pressing the [EXIT] button or [RECORD] button on the panel.

You can select the display

pages (one before and after)

by the using the [BACK]/

[NEXT] buttons or the pedal

(page 131).

Song Playback

CVP-205/203

This function lets you display the lyrics while the song is playing back — making it easy to sing along with your

performance or song playback.

* Microphone input is available only on the CVP-205.

Displaying the Lyrics

Select the

desired song

(page 75, 77).

The contents of the display

can also be shown on a

connected TV (CVP-205

only; page 136, 145).

The lyrics are

in reverse

display along

with song

playback.

Stop the song.

To return to the previous page, press the

button.

EXIT

END

The lyrics can be changed

(page 108).

The language used for lyr-

ics display depends on the

particular lyric data. If the

lyrics are garbled or unread-

able, you can remedy this

by changing the “LYRICS

LANGUAGE” setting from

the SONG SETTING dis-

play (page 129).

Start the song.

REC TOP START / STOP REW FF REPEAT GUIDE

NEW SONG

SYNC.START

REC TOP START / STOP REW FF REPEAT GUIDE

NEW SONG

SYNC.START

If the selected song does

not contain lyric data, lyrics

are not displayed.

If the selected song con-

tains chord data, chord

names are displayed with

the lyrics.

CVP-205/203

Saving and Recalling Custom Panel Setups — Registration Memory

Registration Memory is a powerful feature that lets you set up the Clavinova just as you want — selecting speciﬁc

voices, styles, effect settings etc. — and save your custom panel setup for future recall. Then, when you need those

settings, simply press the appropriate REGISTRATION MEMORY button.

This shows you how to register your custom panel settings to the REGISTRATION

MEMORY buttons. Make all the settings you want with the panel controls, and Registration

Memory will “remember” them for you.

MIN

STYLE

ACMP

MAX

AUTO FILLIN

POWER

OFF

MASTER VOLUME

FADE IN / OUT

METRONOME

START STOP

OTS LINK

BREAK

INTRO

SONG

EXTRA TRACKS

(STYLE)

TRACK 2

(L)

TRACK 1

(R)

REC TOP START / STOP REW FF REPEAT GUIDE

NEW SONG

TEMPO

SYNC.START

RESET

MAIN

TAP TEMPO

TRANSPOSE

RESET

ENDING / rit. SYNC.STOP SYNC.START START / STOP

ABCD

DIRECT ACCESS

DEMO

HELP

FUNCTION

DIGITAL

STUDIO

SOUND

CREATOR

DIGITAL

RECORDING

MIXING

CONSOLE

BALANCE

PART

CHANNEL

ON / OFF

12345678

EXIT

BACK NEXT

VOICE PART

ON / OFF

LAYER

LEFT

LCD

CONTRAST

ENTER

DATA

ENTRY

VOICE EFFECT

REVERB

VOICE

PIANO & HARPSI.

BRASS

MUSIC FINDER

PIANO

DSP VARIATION HARMONY / ECHO MONO LEFT HOLD

E.PIA NO ORGAN & ACCORDION PERCUSSION G UITAR BASS

WOODWIND

STRINGS CHOIR & PAD S YNTH. XG USER

ONE TOUCH SETTING

REGISTRATION MEMORY

FREEZE

MEMORY

12345678

1234

REGISTRATION MEMORY

FREEZE

MEMORY

12345678

Registering Panel Setups — Registration Memory

Keep in mind that songs or

styles on disk cannot

registered to Registration

Memory. If you want to

or style, copy the relevant

data to “USER” in the

SONG/STYLE display

(page 39) and register the

data separately.

REGISTRATION MEMORY

FREEZE

MEMORY

12345678

END

Set up the panel controls as desired.

For a list of the settings that can be registered, refer to the separate Data List

(Parameter Chart).

Select the desired parameter groups

for the settings you want to register.

You can also use the [DATA ENTRY]

dial to navigate in this display. To

the corresponding box. Groups left

without checkmarks will not be included

in the Registration Memory setting.

This allows you to maintain certain

settings, even when switching among

Registration Memory presets. You can

also use the Freeze function (page 87)

to override the Registration Memory

changes — letting you prevent certain

panel settings from being changed.

Enters a checkmark to the

selected box. You can also

use the [ENTER] button.

Removes the checkmark from

the selected box. You can also

use the [ENTER] button.

Cancels the registration

and returns to the MAIN

display. You can also use

the [EXIT] button.

Press the desired number button for registering the settings.

Any data that was previ-

ously registered to the

selected REGISTRATION

MEMORY button (indicator

is green or red) will be

erased and replaced by the

new settings.

Indicator is green......The panel setting is registered, but not selected.

Indicator is red .........The panel setting is registered and is currently selected.

Indicator is off ..........The panel setting is not registered.

REGISTRATION MEMORY

FREEZE

MEMORY

12345678

The registrations registered here will be lost when the power is turned off, unless you perform

the Save operation explained on the next page.

Saving and Recalling Custom Panel Setups — Registration Memory

CVP-205/203

Saving Your Registration Memory Setups

The settings registered to the REGISTRATION MEMORY [1]-[8] buttons are saved as a single ﬁle.

REGISTRATION EDIT display

The contents of the current Registration Memory bank (REGIST.) are listed in the REGISTRATION EDIT screen. The

names of the stored Registration Memory presets are shown in the display and the indicators of the relevant

REGISTRATION MEMORY buttons are lit in green.

From this screen, you can select, name, or delete the Registration Memory presets.

Select ...............Press the [A] - [J] buttons. The REGIST. display is linked to the REGISTRATION MEMORY [1] - [8]

buttons. When you select the Registration Memory preset in the display, the related button turns

on (indicator is red).

Name ...............This operation is the same as that in “Naming Files and Folders” (page 42) in “Basic Operations

— Organizing Your Data.”

Delete ..............This operation is the same as that in “Deleting Files/Folders” (page 44) in “Basic Operations —

Organizing Your Data.”

Keep in mind that the size of

the Registration bank ﬁles

and the memory space they

occupy depends on the

amount of functions set in

each.

BANK 01

All settings registered to buttons [1]-

[8] are referred to as a “bank.” The

banks can be saved to “USER” or

“FLOPPY DISK” as Registration

bank ﬁles.

Press the [DIRECT

ACCESS] button and [EXIT]

button to call up the MAIN

display.

Save the settings you’ve made to the Registration Memory

buttons as a single Registration bank ﬁle (page 45).

The REGISTRATION EDIT display

appears. For details on this display,

see below.

The result of the Name/Delete operation will be lost when the power is turned off unless you return to the REGISTRATION

BANK display by pressing the [8▼] (UP) button and save the data (page 45).

Saving and Recalling Custom Panel Setups — Registration Memory

CVP-205/203

You can recall all of the panel settings you’ve made — or only those you speciﬁcally want or need. For example, if you

de-select “STYLE” in the REGISTRATION MEMORY display, you can keep the currently selected style even when you

change the Registration Memory preset.

Recalling the Registered Settings

Select the desired bank in the REGISTRATION BANK display (page 86).

Press the appropriate REGISTRATION MEMORY button (any whose indicators are

green) to recall the desired settings.

Selecting the Freeze Settings

Recalling a Registration Memory Setup

You can program your

Registration Memory presets

to be called up in sequence,

in any order you desire.

Once programmed, the

presets 1 - 8 can be selected

in sequence with the

[BACK][NEXT] buttons or

the pedal (page 134).

REGISTRATION MEMORY

FREEZE

MEMORY

12345678

DEMO

HELP

FUNCTION

REGISTRATION MEMORY

FREEZE

MEMORY

12345678

REGISTRATION MEMORY

FREEZE

MEMORY

12345678

Select the Freeze settings.

Enters a checkmark

to the selected box.

Press the [FREEZE] button. When Freeze is active (lamp is lit), the settings you speciﬁed in the Freeze

page will be maintained or left unchanged, even when changing Registration Memory presets.

Press the appropriate REGISTRATION MEMORY button (any whose indicators are green) to recall the

desired settings.

Removes the

checkmark from the

selected box.

Call up the “FREEZE”

page from the

REGIST.SEQUENCE/

FREEZE/VOICE SET

screen (page 134).

CVP-205/203

Editing Voices — Sound Creator

The CVP-205/203 has a Sound Creator feature that allows you to create your own voices

by editing some parameters of the existing voices. Once you’ve created a voice, you can

save it as a USER voice for future recall.

• The Voice can be edited in

realtime while playing

back a song/style.

• Keep in mind that adjust-

ments made to the param-

eters may not make much

change in the actual

sound depending on the

original settings of the

voice.

MIN

STYLE

ACMP

MAX

AUTO FILLIN

POWER

OFF

MASTER VOLUME

FADE IN / OUT

METRONOME

START STOP

OTS LINK

BREAK

INTRO

SONG

EXTRA TRACKS

(STYLE)

TRACK 2

(L)

TRACK 1

(R)

REC TOP START / STOP REW FF REPEAT GUIDE

NEW SONG

TEMPO

SYNC.START

RESET

MAIN

TAP TEMPO

TRANSPOSE

RESET

ENDING / rit. SYNC.STOP SYNC.START START / STOP

ABCD

DIRECT ACCESS

DEMO

HELP

FUNCTION

DIGITAL

STUDIO

SOUND

CREATOR

DIGITAL

RECORDING

MIXING

CONSOLE

BALANCE

PAR T

CHANNEL

ON / OFF

12345678

EXIT

BACK NEXT

VOICE PART

ON / OFF

LAYER

LEFT

LCD

CONTRAST

ENTER

DATA

ENTRY

VOICE EFFECT

REVERB

VOICE

PIANO & HARPSI.

BRASS

MUSIC FINDER

PIANO

DSP VARIATION HARMONY / ECHO MONO LEFT HOLD

E.PI ANO ORGAN & ACCORDION PERCUSSION GUITAR BASS

WOODWIND

STRINGS CHOIR & PAD SYNTH. XG USER

ONE TOUCH SETTING

REGISTRATION MEMORY

FREEZE

MEMORY

12345678

1234

SOUND

CREATOR

Operation

DIGITAL

STUDIO

SOUND

CREATOR

DIGITAL

RECORDING

MIXING

CONSOLE

PA RT

Press the [F], [G] or [H] button to select the

Part (MAIN, LAYER or LEFT) containing the

voice you wish to edit.

Indicates the parameters available for editing in

this display. These correspond to the parameters/

values shown at the bottom of the display.

Select the desired menu by

pressing the [NEXT]/

[BACK] button.

Opens the Save (Voice) display

for saving the edited voice as a

User voice (page 45).

Select the desired menu.

The selected menu is highlighted.

Can be used during editing to

compare the sound of the original

voice with the edited voice.

Save the edited voice to the USER drive

(Flash ROM) as a USER voice (page 45).

NATURAL VOICE

The voice can also be

selected in the SOUND

CREATOR display.

Press the

[SOUND

CREATOR]

button.

Edit the voice parameters.

The operations for each function selected in this step are covered in detail, starting on page 90.

REGULAR VOICE

The settings are lost if the

edited part’s voice is

switched to another voice.

Important data should be

saved to User Drive or ﬂoppy

disk.

Press the [USER] button to select the

edited voice, and play the keyboard.

CAUTION

Editing the voice — Sound Creator

CVP-205/203

SOUND CREATOR Parameters

The following parameters are linked to the ones in each display.

PIANO Determines the parameters unique to piano sounds, such as tuning curve or sustain

sampling. This page is available only when the Natural piano voice is selected.

COMMON Determines the common settings such as voice volume or octave.

SOUND Determines the timbre/EG (Envelope Generator)/vibrato of the voice (Regular voice only).

EFFECT Determines the effect depth or type.

HARMONY Determines the Harmony/Echo settings.

Common parameter Other location

MONO VOICE EFFECT (TOP PANEL) page 59

PORTAMENTO TIME MIXING CONSOLE page 121

LEFT PEDAL TYPE CONTROLLER (FUNCTION) page 131

LEFT PEDAL SETTING CONTROLLER (FUNCTION) page 131

FILTER BRIGHTNESS MIXING CONSOLE page 121

FILTER HARMONIC CONTENT MIXING CONSOLE page 121

REVERB DEPTH MIXING CONSOLE page 122

CHORUS DEPTH MIXING CONSOLE page 122

DSP ON/OFF VOICE EFFECT (TOP PANEL) page 58

DSP DEPTH MIXING CONSOLE page 122

DSP TYPE/VARIATION MIXING CONSOLE/VOICE EFFECT (TOP PANEL) page 58,122

HARMONY/ECHO TYPE HARMONY/ECHO (FUNCTION) page 135

HARMONY/ECHO VOLUME HARMONY/ECHO (FUNCTION) page 135

HARMONY/ECHO SPEED HARMONY/ECHO (FUNCTION) page 135

HARMONY/ECHO ASSIGN HARMONY/ECHO (FUNCTION) page 135

HARMONY/ECHO CHORD NOTE ONLY HARMONY/ECHO (FUNCTION) page 135

HARMONY/ECHO TOUCH LIMIT HARMONY/ECHO (FUNCTION) page 135

Natural Voices and Regular Voices

Built into the CVP-205/203 are two different tone generation sources, Natural and

XG. The Natural tone generation source and its voices feature a huge amount of wave

memory, giving you enormous and ﬁnely detailed expressive power over the sound.

The XG source (which powers the Regular voices) provide maximum compatibility

with a wide variety of devices and song data.

The maximum amount of polyphony for each tone generation source is set up to best

enhance your performance. In general, the songs and styles are played back using the

XG source, while the Natural voices are played from the keyboard — allowing you to

play the Natural voices with full polyphony, even if the song and style data exceeds the polyphonic limit.

* Depending on the particular style selected, a Natural voice may be used for the accompaniment. Usually, songs are played back using the

XG voices (page 152); however, you can have them automatically “re-voiced” — using the exceptionally rich and realistic sounds

exclusive to the CVP-205/203 (page 120).

The available parameters

differ depending on the

selected voice type, Regular

or Natural (see below).

Keep in mind that there are

certain parameters whose

Sound Creator settings

affect only the Main part’s

voice.

Voices sounded with the XG

source are divided into two

groups. One is the original

set of Clavinova voices

(Cool!, Sweet!, Live!), and

the other is the conventional

XG set.

Natural! Cool! Sweet! Live! XG

Clavinova-exclusive voices GM/XG-compatible voices

Natural voices (sounded by Natural tone

generation source)

Regular voices (sounded by XG tone generation source)

Used mainly for keyboard-played voices For keyboard-played voices, song/style playback*

Editing the voice — Sound Creator

CVP-205/203

PIANO (Piano Voice has been selected)

The explanations here apply to step #3 on page 88.

COMMON

The explanations here apply to step #3 on page 88.

SOUND (Regular Voice only)

The explanations here apply to step #3 on page 88.

These controls are used to adjust the

brilliance of the tone. This setting

affects all Natural voices globally. When

other than piano voice (Natural) is

selected, set this on EFFECT page.

For details, see the EFFECT page

(page 92).

Determines the tuning curve, especially

for piano voices. Select “FLAT” if you

feel the tuning curve of the piano voice

does not quite match that of other

instruments voices.

STRETCH .. Tuning curve particularly

for pianos

FLAT .......... Tuning curve in which the

frequency is octave

doubled over the entire

keyboard range

Determines the depth of

sustain sampling for the

damper pedal.

The available parameters

differ depending on the

selected voice.

Set the volume of the current edited

voice.

Set the portamento time of each

part (MAIN/LAYER/VOICE)

(Regular Voice only) (page 121).

Determines the touch sensitivity, or

how greatly the volume responds to

your playing strength.

0 —– – Produces more dramatic

level drops, the more softly

you play.

—

– Normal response.

127— Produces high volume for

any playing strength (ﬁxed)

Shift the octave range of the

selected voice up or down in

octaves. When the Main or Layer

part’s voice is used, the M/LYR

parameter is available; when the

Left part’s voice is used, the LEFT

parameter is available.

The parameters are the same

as for CONTROLLER display.

For details, see page 131.

This determines whether the voice

is played monophonically (Regular

Voice only) (page 59).

Determines the ﬁlter, EG, and

vibrato settings (see below).

Editing the voice — Sound Creator

CVP-205/203

■ FILTER

FILTER settings determine the overall timbre of the sound by boosting or cutting a

certain frequency range.

■ EG

The EG (Envelope Generator) settings determine how the level of the sound changes in time. This lets you reproduce

many sound characteristics of natural acoustic instruments — such as the quick attack and decay of percussion

sounds, or the long release of a sustained piano tone.

• ATTACK ...... Determines how quickly the sound reaches its maximum

level after the key is played. The higher the value, the

slower the attack.

• DECAY........ Determines how quickly the sound reaches its sustain

level (a slightly lower level than maximum). The higher

the value, the slower the decay.

• RELEASE ..... Determines how quickly the sound decays to silence after

the key is released. The higher the value, the slower the release.

■ VIBRATO

• DEPTH........ Determines the intensity of the Vibrato effect (see diagram). Higher

settings result in a more pronounced Vibrato.

• SPEED......... Determines the speed of the Vibrato effect (see diagram).

• DELAY ........ Determines the amount of time that elapses between the

playing of a key and the start of the Vibrato effect (see

diagram). Higher settings increase the delay of the Vibrato

onset.

In addition to making the

sound either brighter or

more mellow, Filter can be

used to produce electronic,

synthesizer-like effects.

Cutoff frequency

Volume

Frequency

(pitch)

Cutoff range

These frequencies are

“passed” by the filter.

• BRIGHTNESS

Determines the cutoff frequency or

effective frequency range of the ﬁlter (see

diagram). Higher values result in a

brighter sound.

Resonance

• Harmonic Content

Determines the emphasis given to the

cutoff frequency (resonance), set in

BRIGHTNESS above (see diagram).

Higher values result in a more

pronounced effect.

Resonance

Volume

Frequency

(pitch)

Time

Level

Key on

Key off

ATTACK RELEASE

DECAY

If RELEASE is set to a large

value, the sustain becomes

long.

VIBRATO

Creates a wavering in the

sound by periodically chang-

ing the pitch.

DEPTH

SPEED

DELAY

Time

Level

Editing the voice — Sound Creator

CVP-205/203

EFFECT

The explanations here apply to step #3 on page 88.

HARMONY

The explanations here apply to step #3 on page 88.

The parameters are the same as for HARMONY/ECHO display of FUNCTION. For details, see page 136.

Determines the effect type (Reverb/

Chorus/DSP) for the Natural voices.

When a regular voice is selected, the

DSP type and Variation are set in two

separate menus. For information on the

effect structure, see page 124; for a list

of available effect types, refer to the

separate Data List.

Determines the brilliance of the tone,

when a Natural voice is selected (CVP-

205 only). This can also be set from the

PIANO page (page 90), when a piano

voice is selected.

• Metallic ......... Sharp metallic tone

• Bright............ Bright tone

• Normal.......... Standard tone

• Mellow .......... Soft and mellow tone

• Dark .............. Dark tone

The same as the “Mixing Console”

on page 122.

• If you select [Bright] or

[Metallic] as the type of

brilliance, the volume level

will increase slightly. In

this case, raising the

[MASTER VOLUME] may

result in distortion. If this

happens, lower the vol-

ume accordingly.

•“SPEED” parameter is

added when selecting

VIBE ROTOR DSP type.

This parameter enables

you to set the speed of

vibrato when you select

the Vibraphone voice, rec-

reating the effect of a vibe

rotor pedal.

This parameter enables you to select whether the

sound is sustained while you press the keys on

the keyboard (“PIANO LIKE”), or the sound is

sustained only while you press and hold down the

sustain pedal, like playing a real vibraphone

(“NORMAL”) (for Vibraphone voice).

CVP-205/203

Recording Your Performances and Creating Songs

— Song Creator

With these powerful yet easy-to-use song creating features, you can record your own keyboard performances and store

them for future recall. Several different recording methods are available: Quick Recording (page 94), which lets you

record easily and quickly; Multi Recording (page 95), which lets you record several different parts; and Step Recording

(page 97), which lets you enter notes one by one. Songs can include not only the voice settings for the keyboard

performance (Main, Layer, Left), but also the effects and auto accompaniment parts. The recorded song can be stored to

internal memory or ﬂoppy disk (page 39, 45).

About Song Recording

■ Quick Recording (page 94)

This is the easiest recording method, and lets you quickly record the piano

song you are practicing. You can select from three parts: right hand, left hand

and auto accompaniment. For example, you can record only your right hand

performance, or you can simultaneously record both your right hand and the

auto accompaniment.

■ Multi Recording (page 95)

This lets you record a song with several different instrument sounds, and create

the sound of a full band or orchestra. Record the performance of each

instrument individually and create fully orchestrated compositions. You can

also record over an existing part on an internal song or a song on disk with

your own performance.

■ Step Recording (page 97)

This method is like writing music notation on paper. It lets you enter each note

individually, by specifying the pitch and length. This is ideal for making precise

recordings, or for recording parts that are difﬁcult to play.

■ Song Editing (page 103)

The CVP-205/203 also lets you edit the songs you’ve recorded by the Quick

Recording, Multi Recording and Step Recording methods.

MIN

STYLE

ACMP

MAX

AUTO FILLIN

POWER

OFF

MASTER VOLUME

FADE IN / OUT

METRONOME

START STOP

OTS LINK

BREAK

INTRO

SONG

EXTRA TRACKS

(STYLE)

TRACK 2

(L)

TRACK 1

(R)

REC TOP START / STOP REW FF REPEAT GUIDE

NEW SONG

TEMPO

SYNC.START

RESET

MAIN

TAP TEMPO

TRANSPOSE

RESET

ENDING / rit. SYNC.STOP SYNC.START START / STOP

ABCD

DIRECT ACCESS

DEMO

HELP

FUNCTION

DIGITAL

STUDIO

SOUND

CREATOR

DIGITAL

RECORDING

MIXING

CONSOLE

BALANCE

PAR T

CHANNEL

ON / OFF

12345678

EXIT

BACK NEXT

VOICE PART

ON / OFF

LAYER

LEFT

LCD

CONTRAST

ENTER

DATA

ENTRY

VOICE EFFECT

REVERB

VOICE

PIANO & HARPSI.

BRASS

MUSIC FINDER

PIANO

DSP VARIATION HARMONY / ECHO MONO LEFT HOLD

E.PI ANO ORGAN & ACCORDION PERCUSSION GUITAR BASS

WOODWIND

STRINGS CHOIR & PAD SYNTH. XG USER

ONE TOUCH SETTING

REGISTRATION MEMORY

FREEZE

MEMORY

12345678

1234

SONG

EXTRA TRACKS

(STYLE)

TRACK 2

(L)

TRACK 1

(R)

REC TOP START / STOP REW FF REPEAT GUIDE

NEW SONG

SYNC.START

DIGITAL

RECORDING

• The internal memory capacity of

the Clavinova is about 580KB.

Memory capacity for 2DD and 2HD

ﬂoppy disks is about 720KB and

1.44MB, respectively. When you

store data to these locations, all ﬁle

types of the Clavinova (Voice,

Style, Song, Registration, etc.) are

stored together.

• The microphone input signal (CVP-

205 only) cannot be recorded.

• Songs recorded on theCVP-205/

203 are automatically recorded as

SMF (Standard MIDI File format 0)

data. For details on SMF see

page 151.

• Playback of the recorded song

data can be transmitted from MIDI

OUT, letting you play the sounds of

a connected external tone genera-

tor (page 138).

• The volume level of each channel

of the song can be adjusted from

the Mixing Console and the set-

tings can be saved. Moreover, even

after you’ve set a voice for your

keyboard play during recording,

you can record voice selections, so

that the voice changes automati-

cally during playback (page 105).

Recording Your Performances and Creating Songs— Song Creator

CVP-205/203

This is the easiest recording method — perfect for quickly recording and playing back a piano song you’re practicing, so

you can check your progress.

■ Play back your new song

To play back the performance you just recorded, return the song to the beginning by

using the [TOP] button and press the SONG [START/STOP] button.

Playback stops automatically at the end of the song, and returns to the beginning of the

song.

You can edit the recorded song data from the SONG CREATOR (1 - 16) displays (page 106).

Press the [6▼] button from the Open/Save display for Song to store the recorded data

(page 39, 45).

Quick Recording

REC TOP START / STOP REW FF REPEAT

NEW SONG

SYNC.START

■ When creating a new song:

■ When recording over the part of an internal

song or a song on disk with your own

performance:

Select the desired song (page 75, 77).

Select the voice and accompaniment style you want to use in the song.

If you want to record to the Layer/Left voices, make sure to set the [LAYER]/[LEFT] buttons to ON.

Make any other desired settings (Reverb, Chorus, etc.) as well.

Simultaneously hold down the [REC] button and press the button

corresponding to the track you want to record.

You can select TRACK 1 or TRACK 2 and the EXTRA TRACKS for recording at the

same time.

To record your keyboard performance:

Press either the [TRACK 1] or [TRACK 2] button.

To record the auto accompaniment performance:

Press the [EXTRA TRACKS] button.

To stop recording, press

the [REC] button again.

If the “LAYER” or “LEFT”

button is on before pressing

the REC button, the corre-

sponding Layer and Left parts

are automatically recorded to

different channels.

The performance of track 1/2

is recorded to the channel

speciﬁed in the SONG SET-

TING display (page 129).

Recording starts as soon as you play the keyboard.

You can also start recording by pressing the SONG/

STYLE [START/STOP] button. Recording can also be

started by pressing down the pedal, if the song start/stop

function is properly assigned to the pedal (page 131).

To stop recording, press the [RECORD] button again.

Recording can also be stopped by pressing down the pedal, if the song start/

stop function is properly assigned to the pedal (page 131).

END

To pause, press the SONG

[START/STOP] button. To

resume recording, press the

SONG [START/STOP] but-

ton again.

You can also use the metro-

nome click as a guide while

recording.

The sound of the metronome

is not recorded.

You can overdub a second

right-hand performance onto

Track 2 after recording the

ﬁrst right-hand performance

(including the layer voices)

on Track 1. To do this, set the

[LEFT] button to OFF and

repeat steps 2 and 3.

REC

EXTRA TRACKS

(STYLE)

TRACK 2

(L)

TRACK 1

(R)

Turning off the power

automatically deletes your

recorded performance. If

you wish to save the

recording, make sure to

store it to internal mem-

ory (USER drive) or ﬂoppy

disk (page 39, 45).

CAUTION

Recording Your Performances and Creating Songs— Song Creator

CVP-205/203

This lets you record a song with several different instrument sounds on up to sixteen channels, and create the sound of

a full band or orchestra.

The structure of the channels and parts are shown in the chart below.

About the accompaniment style parts

Rhythm .....This is the basis for the accompaniment, containing the drum and percussion rhythm patterns. Usually one of the drum kits is used.

Bass..........The Bass part uses various appropriate instrument sounds to match the style, such as acoustic bass, synth bass, and others.

Chord........This is the rhythmic chord backing, commonly used with piano or guitar voices.

Pad ............This part features sustained chords and commonly uses lush sounds such as strings, organ, and choir.

Phrase ......This part is used for various embellishments and riffs that enhance the song, such as brass section accents and chord arpeggios.

Channels

Parts

(default settings)

Available parts Channels

Parts

(default settings)

Available parts

1 Voice MAIN

Voice MAIN, LAYER, LEFT

Accompaniment style RHYTHM 1

Accompaniment style RHYTHM 2

Accompaniment style BASS

Accompaniment style CHORD1

Accompaniment style CHORD2

Accompaniment style PAD

Accompaniment style PHRASE1

Accompaniment style PHRASE2

MIDI

Accompaniment style

RHYTHM 1

Voice MAIN, LAYER, LEFT

Accompaniment style RHYTHM 1

Accompaniment style RHYTHM 2

Accompaniment style BASS

Accompaniment style CHORD1

Accompaniment style CHORD2

Accompaniment style PAD

Accompaniment style PHRASE1

Accompaniment style PHRASE2

MIDI

2 Voice MAIN 10

Accompaniment style

RHYTHM 2

3 Voice MAIN 11

Accompaniment style

BASS

4 Voice MAIN 12

Accompaniment style

CHORD1

5 Voice MAIN 13

Accompaniment style

CHORD2

6 Voice MAIN 14

Accompaniment style

PA D

7 Voice MAIN 15

Accompaniment style

PHRASE1

8 Voice MAIN 16

Accompaniment style

PHRASE2

Multi Recording

REC TOP START / STOP REW FF REPEAT

NEW SONG

SYNC.START

REC

■ When creating a new song:

■ When recording over the part of an internal

song or a song on disk with your own

performance:

Select the desired song (page 75, 77).

Select the desired channel for recording (set it to “REC”) simultaneously

holding down the [REC] button and pressing the appropriate button [1▲▼]

- [8▲▼]. Several channels can be selected at the same time.

REC......................... Enables recording for the channel

ON ......................... Enables playback of the channel

OFF......................... Mutes the channel

To cancel or disable recording, press the [REC] button once again.

The part is automatically

selected when setting the

several channels to “REC” at

the same time.

Recording Your Performances and Creating Songs— Song Creator

CVP-205/203

Select the part you want to assign to the channel to be recorded.

This determines which of the keyboard-played parts (Main/Layer/Left) and the

accompaniment style parts (RHYTHM 1/2, BASS, etc.) are recorded to the

recording channels selected in step #2.

For a list of the initial default assignments, see page 95.

When selecting the MIDI

part

• Setting a single channel

to MIDI

All incoming data received

via any of the MIDI chan-

nels 1 - 16 is recorded.

When using an external

MIDI keyboard or control-

ler to record, this lets you

record without having to

set the MIDI transmit

channel on the external

device.

• Setting several channels

to MIDI

When using an external

MIDI keyboard or control-

ler to record, this records

data only over the set

MIDI channel — meaning

the external device must

also be set to the same

channel.

A single part (with the

exception of MIDI parts) can-

not be assigned to several

channels.

Recording starts as soon as you play the keyboard.

You can also start recording by pressing the

SONG/STYLE [START/STOP] button. The

recording can be started/stopped by pressing the

pedal if the recording punch in/out function is set

to the pedal (page 102).

To stop recording, press the [REC] button again.

You can also use the pedal to stop recording by releasing it, if the recording

punch in/out function has been assigned to the pedal (page 102).

To pause, press the SONG

[START/STOP] button. To

resume recording, press the

SONG [START/STOP] but-

ton again.

You can also use the metro-

nome click as a guide while

recording.

The sound of the metronome

is not recorded.

Play back your new song.

To play back the performance you just recorded, return the song to the

beginning by using the [TOP] button and press the SONG [START/STOP]

button.

Playback stops automatically at the end of the song, and returns to the

beginning of the song.

To record a new part, repeat steps 2 - 6 above.

You can set previously recorded parts to play back, and monitor them

while you record a new part. Continue in this way until you have a

ﬁnished song.

You can edit the recorded song data from the SONG CREATOR (1 - 16)

displays (page 106).

Press the [6▼] button from the Open/Save display for Song to store

the recorded data (page 39, 45).

END

Turning off the power

automatically deletes your

recorded performance. If

you wish to save the

recording, make sure to

store it to internal mem-

ory (USER drive) or ﬂoppy

disk (page 39, 45).

The settings of the recorded

parts is stored temporarily

until you execute Quick

Recording, select a song, or

turn the power off.

CAUTION

Recording Your Performances and Creating Songs— Song Creator

CVP-205/203

This method lets you create a song by entering notes one by one, without having to perform them in real time. This is

also convenient for recording the chords and the melody separately.

Operation

Recording Individual Notes — Step Record

DIGITAL

STUDIO

SOUND

CREATOR

DIGITAL

RECORDING

MIXING

CONSOLE

PA RT

Select an existing song (page 75, 77) to

which you want to add parts or re-record.

If you want to create a new song,

simultaneously press the [RECORD] button

and the [TOP] button.

Press the [A] button to call up the Song

Creator display.

Press the [DIGITAL RECORDING] button.

Using the [BACK]/[NEXT]

buttons, select the “1 -16”

tab for recording melodies

and other parts, or select

the “CHD” (Chord) tab for

recording chords, and after

selecting the “1-16” tab,

select a record channel

with the [F] (CH) button.

BACK NEXT

Call up the Step Record

display by pressing the

[G] button.

Any voice, effect and other

settings you make in the

Mixing Console are automat-

ically cancelled when you

call up the CHD (Chord)

page.

The voices in the USER and

FLOPPY DISK pages can-

not be selected for Step

recording. You can select

voices from the PRESET

page; however, these may

sound slightly different from

the original voice.

Recording Your Performances and Creating Songs— Song Creator

CVP-205/203

■ Measure/Beat/Clock

■ Velocity

The table below shows the available settings and the corresponding velocity values.

■ Gate Time

The following settings are available:

Normal ....................... 80%

Tenuto ........................ 99%

Staccato...................... 40%

Staccatissimo.............. 20%

Manual .......................

The gate time (note length) can be speciﬁed as a percentage by using the [DATA ENTRY] dial.

Kbd. Vel fff ff f mf mp p pp ppp

Actual

playing

strength

127 111 95 79 63 47 31 15

Moves the cursor position

up and down.

Returns the cursor to the

beginning of the song (the

ﬁrst note of the ﬁrst

measure).

Determines the velocity

(loudness) of the note to be

entered (only when recording

the melody). For information

on velocity settings, see below.

Determines the length of the

note (as a percentage) from

the position at which it is to be

entered. (This is available only

when recording the melody.)

For information on gate time

settings, see below.

Each press of this button toggles

among the three basic note

selectors at the bottom of the

display: normal, dotted, and triplet.

(This is available only when

recording the melody.)

Deletes the event at the cursor.

Use these to move the

selected event, in units of

measures (BAR), beat, and

clocks. For information on

measure/beat/clock settings,

see below.

Speciﬁes the type of note to be input next. (Sixteenth

notes are available only when recording the melody.)

This also determines the position to which the pointer

will advance after a note has been entered.

First, select the desired voice. To enter the note, ﬁrst specify the length and loudness in this display,

then enter the pitch by actually playing the note on the keyboard.

To close the STEP RECORD display, press the [EXIT] button. Make sure to store the recorded

data by pressing the [I] (SAVE) button (page 45).

END

Measure

Beat

Clock

000-

1919

000-

1919

000-

1919

000-

1919

000-

1919

000-

1919

000-

1919

000-

1919

Recording Your Performances and Creating Songs— Song Creator

CVP-205/203

Recording Melodies — Step Record (Note)

In this section, we’ll show you how to use Step Recording

by guiding you through this actual music example,

shown at right.

The operations here apply to step 6 on page 98.

■ Play back the newly created melody

Use the [C] ( ) button to move the cursor to the beginning of the song, and press the SONG [START/STOP] button

to hear the newly entered notes. To actually enter the recorded data, press the [EXIT] button. The entered data can be

edited from the SONG CREATOR (1 - 16) display (page 106).

1-1 Select this note.

1-3 ...press this (to input a tie).

1-2 While holding down this note...

2-2

2-3

2-4

2-1 Select this note.

3-1 Press this button to

display the dotted notes.

3-2 Select this note.

3-3

4-1 Call up the normal notes

by pressing this button.

4-3

4-2 Select this note.

The notation display on the instrument (CVP-205) may not be

accurate, especially for tied notes or longer notes. To have the

notation displayed accurately, set the gate time to tenuto by

using the [H] button, and input the notes as desired.

To input rests, simply move the measure/beat/clock location for the desired rest time, then input the next note.

▲

Recording Your Performances and Creating Songs— Song Creator

CVP-205/203

100

Recording Chord Changes for the Auto Accompaniment — Step

Record (Chord)

The Chord Step recording feature makes it possible to record auto accompaniment chord changes one at a time with

precise timing. Since the changes don’t have to be played in real time, you can easily create complex, tight chord

changes — over which you can record the melody in normal fashion.

The operations here apply to step 6 on page 98.

Entering Chords and Sections (Chord Step)

For example, you can input the following chord progression by the procedure described below.

C F G F G7 C

MAIN A BREAK MAIN B

Enter the chords by using the currently

selected chord ﬁngering method in the Auto

Accompaniment section of the keyboard.

Press the MAIN [A] button to specify the section, and enter the chords as shown at right.

C F G

MAIN A

MAIN

Select this note value and play

the chords indicated at right.

001:1:000

001:3:000

002:1:000

C F G F G7

MAIN A BREAK

BREAK

INTRO

002:3:000

002:4:000

Press the [BREAK] button to specify the Break section, and enter the chords as shown at right.

Select this note value and play

the chords indicated at right.

Recording Your Performances and Creating Songs— Song Creator

101

CVP-205/203

■ Play back the newly created chord progression

Use the [C] ( ) button to move the cursor to the beginning of the song, and press the

SONG [START/STOP] button to hear the newly entered notes. To actually enter the

recorded data, press the [EXIT] button. The entered data can be edited from the SONG

CREATOR (CHD) display (page 107). Finally, press the [F] (EXPAND) button from the

SONG CREATOR (CHD) display in order to convert the input data into song data.

Press the MAIN [B] button to specify the section and enter the chord indicated at right.

C F G F G7 C

MAIN A BREAK MAIN B

MAIN

003:1:000

Select this note value and play

the chords indicated at right.

To enter a ﬁll-in, press the

[AUTO FILL IN] button and

press one of the MAIN [A] –

[D] buttons.

END Mark

An “END” mark is shown in

the display, indicating the

end of the song data.

The actual position of the

End mark differs depending

on the section that is input at

the end of the song. When

an Ending section is input,

the End mark automatically

follows the Ending data.

When a section other than

Ending is input, the End

mark is set two measures

after the ﬁnal section.

The End mark can be freely

set to any position desired.

▲

Recording Your Performances and Creating Songs— Song Creator

CVP-205/203

102

From this display you can set up how recording is started and stopped for either Quick Recording or Multi Recording.

To call up these settings, select the REC MODE display by using the [BACK][NEXT] button, after performing operation

steps 1 - 3 on page 97.

About Punch In/Out

This feature is useful primarily for re-recording or replacing a speciﬁc section of an already recorded channel. The

illustrations below indicate a variety of situations in which selected measures in an eight-measure phrase are re-recorded.

Select the Recording Options: Starting, Stopping,

Punching In/Out — Rec Mode

Determines the measure at which Punch

In overwrite recording starts (when

“PUNCH IN AT” is selected).

These settings determine how recording will

start.

Normal

Pressing the SONG [START/STOP] button

enables Synchro standby and overwrite

recording starts as soon as you start playing

the keyboard.

First Key On

Overwrite recording starts as soon as you

start playing the keyboard. This setting also

preserves the previous lead-in data, letting

you record over the original lead-in without

erasing it.

Punch In At

The song plays back normally up to the

indicated Punch In measure (set by the

[3▲▼] buttons), then starts overwrite

recording at that Punch In measure.

These settings determine how recording

will stop as well as what happens to

previously recorded data.

Determines the Punch Out

measure — the measure at

which Punch In overwrite

recording stops (when

“PUNCH OUT AT” is

selected).

When this is set to ON, you

can use the sostenuto

(center) pedal to control the

punch-in and punch-out

points. Press and hold

down the sostenuto pedal to

record. Recording stops

when you release the pedal.

Calls up the SONG display,

from which you can save the

edited data.

When the Pedal Punch In/

Out function is set to ON, the

current function assignment

of the sostenuto pedal is

cancelled.

Replace All

This deletes all data following the point at which

recording is stopped.

Punch Out

This maintains all data following the point at which recording is stopped.

Punch Out At

Overwrite recording continues until the indicated Punch Out measure (set by the [6▲▼] buttons),

then stops at that Punch Out measure, after which song playback continues normally.

12345678

REC START setting

REC END setting

12345

Deleted

Start/start overwrite recording

Original data

Previously recorded data

Newly recorded data

Deleted data

NORMAL

REPLACE ALL

12345678

NORMAL

PUNCH OUT

12345678

NORMAL

PUNCH OUT AT=006

12345

Start/

play back original data

Start/

play back original data

Start/

play back original data

Start/

play back original data

Start/

play back original data

Start/

play back original data

Start playing the keys/

start overwrite recording

Start playing the keys/

start overwrite recording

Start playing the keys/

start overwrite recording

Start overwrite recording

Stop recording

FIRST KEY ON

REPLACE ALL

12345678

FIRST KEY ON

PUNCH OUT

12345678

Stop overwrite recording/

play original data

Stop overwrite recording/

play original data

Stop overwrite recording/

play original data

FIRST KEY ON

PUNCH OUT AT=006

12345

PUNCH IN AT=003

REPLACE ALL

12345678

PUNCH IN AT=003

PUNCH OUT

12345 7

PUNCH IN AT=003

PUNCH OUT AT=006

*1 When measures 1 - 2 are not

overwritten, recording starts

from measure 3.

*2 You’ll have to press the [REC]

button at the end of 5 measures.

Start/start overwrite recording

Stop recording

Recording Your Performances and Creating Songs— Song Creator

103

CVP-205/203

Whether you’ve recorded a song using Quick Recording, Multi Recording, or Step Recording, you can use the editing

features to change the song data.

Editing Channel-related Parameters — Channel

Calling up the operations here apply to step 4 on page 97. To call up the display shown below, use the [BACK]/[NEXT]

buttons.

Quantize

Quantize lets you “clean up” or tighten the timing of a previously recorded channel. For example, the following

musical passage has been written with exact quarter-note and eighth-note values.

Even though you think you may have recorded the passage accurately, your actual performance may be slightly ahead

of or behind the beat. Quantize allows you to align all the notes in a channel so that the timing is absolutely accurate to

the speciﬁed note value (see below).

■ About Quantize Size

Set the Quantize size to correspond to the smallest notes in the channel you are working with. For example, if the

data was recorded with both quarter notes and eighth notes, use 1/8 note for the Quantize size. If you apply a 1/4

note Quantize size, the eighth notes would be moved on top of the quarter notes.

Editing a Recorded Song

Use this to select the

desired edit operation.

Selects the desired

channel to be quantized.

Selects the quantize size (resolution).

See the below for the details.

Determines how strongly the

notes will be quantized. If a

value less than 100% is

selected, notes will be

moved toward the speciﬁed

quantization beats only by

the speciﬁed amount.

Applying less than 100%

quantization lets you

preserve some of the

“human” feel in the

recording.

Executes the Quantize

operation. After the

operation is completed, this

button changes to [UNDO],

letting you restore the

original data if you’re not

satisﬁed with the Quantize

results. The Undo function

only has one level; only the

previous operation can be

undone.

Calls up the SONG display,

from which you can save

the edited data.

One measure of eighth notes before quantization After 1/8 note quantization

1/8 note 1/16 note 1/32 note 1/16 note +

1/8 note triplet *

1/4 note

1/4 note triplet 1/8 note triplet 1/16 note triplet 1/8 note +

1/8 note triplet *

1/16 note +

1/16 note triplet *

The three Quantize settings marked with asterisks (*) are exceptionally convenient, since they allow you to quantize two different

note values at the same time, without compromising the quantization of either one. For example, if you have both straight 1/8 notes

and 1/8 note triplets recorded to the same channel, and you quantize to straight 1/8 notes, all notes in the channel are quantized to

straight 1/8 notes — completely eliminating any triplet feel in the rhythm. However, if you use the 1/8 note + 1/8 note triplet setting,

both the straight and triplet notes will be quantized correctly.

Quantize Size

Recording Your Performances and Creating Songs— Song Creator

CVP-205/203

104

Delete

This lets you delete recorded data in the speciﬁed channel.

Mix

This function lets you mix the data of two channels and place the results in a different channel. It also lets you copy the

data from one channel to another.

Use these to select the

desired edit operation.

Deletes all data in the

selected channel. After the

operation is completed, this

button changes to [UNDO],

letting you restore the

original data. The Undo

function only has one level;

only the previous operation

can be undone.

Calls up the SONG display,

from which you can save

the edited data.

These select the channel to be deleted.

Use these to select the

desired edit operation.

Executes the Mix operation.

After the operation is

completed, this button

changes to [UNDO], letting

you restore the original data

if you’re not satisﬁed with

the Mix results. The Undo

function only has one level;

only the previous operation

can be undone.

Calls up the SONG display,

from which you can save

the edited data.

These let you specify the two

source channels to be mixed.

If “COPY” is selected here, the data

from Source 1 is copied to the

Destination channel.

Determines the channel into which the

mix or copy results will be placed.

All data other than the mixed

note data is derived from the

Source 1 channel.

Recording Your Performances and Creating Songs— Song Creator

105

CVP-205/203

Channel Transpose

This allows you to transpose the recorded data of individual channels up or down by a maximum of two octaves in

semitone increments.

Set Up

You can change the initial settings of the song — such as voice, level, and tempo — to the current settings of the mixing

console or panel controls.

Executes the Channel

Transpose operation. After

the operation is completed,

this button changes to

[UNDO], letting you restore

the original data if you’re not

satisﬁed with the Channel

Transpose results. The

Undo function only has one

level; only the previous

operation can be undone.

Calls up the SONG display,

from which you can save

the edited data.

Determines the amount of transpose for each channel.

Toggles between the two

channel displays: Channels

1 - 8, and Channels 9 - 16.

To simultaneously set all

channels to the same value,

adjust the Channel

Transpose for one of the

channels while holding down

this button.

Use these to select the

desired edit operation.

Use these to select the

desired edit operation.

Executes the SET

UP operation. Once

SET UP has been

executed, the

operation cannot be

cancelled or undone.

Calls up the SONG display,

from which you can save

the edited data.

Determines which playback features and functions will be automatically called up along with the selected song. All

events, with the exception of “KEYBOARD VOICE,” can be recorded only at the beginning of the song.

Before you select or checkmark any of these items (other than Keyboard Voice), make sure to return the song to the

beginning by using the [TOP] button, and stop playback.

Song.............................Stores the tempo setting and all settings made from the Mixing Console.

Keyboard Voice ...........This lets you automatically set the voice of the keyboard-played parts (Main/Layer/Left)

when playing back the song. Stores the keyboard-played voice and the part ON/OFF

settings. To record a voice change for the keyboard-played part in the middle of a song, stop

the song at the desired point, make the voice change, and press the [D] (EXECUTE) button.

Lyrics Language .........Stores the settings of the Lyrics display.

Score Setting ..............Stores the settings of the Score display (CVP-205 only).

Guide Setting ..............Stores the settings of the practice functions. When the settings are stored, selecting a song

automatically turns on the Guide functions.

Mic. Setting..................Stores the microphone settings in the mixing console (CVP-205 only).

Use this to checkmark the

selected item.

Checkmarked items are

stored with the song.

Recording Your Performances and Creating Songs— Song Creator

CVP-205/203

106

Editing Note Events — 1 - 16

From this display, you can edit individual note events (see below). Calling up operations here apply to step 4 on

page 97. Use the [BACK]/[NEXT] buttons to call up the display below.

Note Events

Parameter Description

Note Determines the pitch, velocity (volume) and length of the note.

Ctrl (Control change)

Determines the control change number and value. For details on control change messages, refer to the separate

Data List booklet (MIDI Data Format).

Prog (Program change)

Determines the voice (program) number. For details on program change messages and how to set them, refer to

the separate Data List booklet (Voice List).

P.Bnd (Pitch bend) Determines the pitch bend value.

A.T. (After touch) Determines the after touch value.

Use these to move the

cursor up/down and select

the desired event.

Determines the channel to

be edited.

For coarse adjustment of the event value.

Calls up the Step Recording

display (page 98).

Calls up the Filter display

(page 108), letting you select

only the events you wish to

shown in the Event List.

Calls up the SONG display,

from which you can save

the edited data.

Holding this button down

while using the [A] and [B]

buttons lets you select

multiple events.

For ﬁne adjustment of the event value.

Cuts (deletes) all selected events. The cut events

are copied and can be pasted to another location.

Adds a new event to the Event List.

Copies all selected events. The

copied events can be pasted to

another location.

Deletes the

event at the

cursor position.

Pastes all cut or copied events to

the selected location.

If the value at the cursor has been

changed, pressing this restores the

original value.

Determines the current

position of the event being

edited.

Returns to the beginning

position of the current song

(the ﬁrst note of the ﬁrst

measure).

Use these to move the

cursor left/right and select

the desired parameter of

the highlighted event. Keep

in mind that moving the

cursor away from the just-

edited value automatically

enters that value.

To actually enter an edited

value, move the cursor away

from the value or press the

SONG [START/STOP] but-

ton.

The sound of the voices

recorded with Step recording

may sound slightly different

from the original.

Recording Your Performances and Creating Songs— Song Creator

107

CVP-205/203

Editing Chord Events — CHD

From this display, you can edit the chord events you’ve recorded to the song.

Calling up operations here apply to step 4 on page 97. Use the [BACK]/[NEXT] buttons to call up the display below.

With the exception of the [F] (EXPAND) button, the operations here are the same as those in Editing Note Events

(page 106).

Chord Events

Editing System Events — SYS/EX. (System Exclusive)

From this display, you can edit recorded System events.

Calling up operations here apply to step 4 on page 97. Use the [BACK]/[NEXT] buttons to call up the display below. The

operations here are the same as those in Editing Note Events (page 106).

System Events

Parameter Description

Style (Accompaniment

style)

Displays the accompaniment style name. To enter an accompaniment style, call up the STYLE display and select

the desired style.

Tempo Determines the tempo value.

Chord Speciﬁes the chord — its root note, chord type, and on-bass note.

Sect (Section) Speciﬁes the section — its name and variation.

OnOff (Channel on/off) Determines whether speciﬁc channels (rhythm, bass, etc.) are turned on/off.

CH.Vol (Channel volume) Determines the level of speciﬁc channels (rhythm, bass, etc.).

S.Vol (Style volume) Determines the level of the entire accompaniment style.

Parameter Description

ScBar (Score initial measure) This determines the number of the top measure. The measure number is indicated in the MAIN display or in the

music notation (CVP-205 only). Only one value can be speciﬁed at the beginning of the song data.

Tempo Determines the tempo value.

Time (Time signature) Determines the time signature.

Key Determines the key, as well as the major/minor setting.

XG Prm (XG parameters) Allows you to make various detailed changes to the data. For more information on XG parameters, refer to the

separate Data List booklet (MIDI Data Format).

SysEx (System Exclusive) Displays the System Exclusive data in the song. This does not let you change the actual contents of the data;

however, it lets you delete, cut, copy, and paste the data.

Meta (Meta event) Displays the SMF meta events in the song. This does not let you change the actual contents of the data;

however, it lets you delete, cut, copy, and paste the data.

Press this to convert the

recorded chord and section

entries into song data.

To actually enter an edited

value, move the cursor away

from the value or press the

SONG [START/STOP] but-

ton.

Recording Your Performances and Creating Songs— Song Creator

CVP-205/203

108

Inputting and Editing Lyrics

This convenient function lets you enter the song name and the lyrics for the song. It also lets you change or correct

already existing lyrics. For more information on lyric events, see the chart below. Calling up operations here apply to

step 4 on page 97. Use the [BACK]/[NEXT] buttons to call up the display below. The operations here are the same as

those in Editing Note Events (page 106).

In the following example, we’ll rewrite a portion of the lyrics to one of the songs, “Twinkle Twinkle Little Star.”

Select the disk song (CVP-203) / internal song (CVP-205) “Twinkle Twinkle Little Star.” The method for selection is the

same as described on page 75.

Lyrics Events

Customizing the Event List — Filter

This function lets you determine which event types will be shown in the event editing displays. To select an event for

display, checkmark the box corresponding to the event name. To ﬁlter out an event so that it is not shown on the list,

remove the checkmark so that the box is empty.

To call up the display below, press the [H] (FILTER) button from any of the following displays: CHD, 1 - 16, SysEX, or

LYRICS (page 106 - page 108).

Parameter Description

Name (Song name) Determines the song name. This calls up the NAME display, from which you can enter the name.

Lyrics Allows you to enter lyrics.

Code (Other controls) CR : Enters a line break in the lyrics text.

LF : Deletes the currently displayed lyrics and displays the next set of lyrics.

Move the cursor

to the event

containing the

lyric “star.”

Use these buttons to call up the Lyric display, from which you can input lyrics.

From the Lyric display (page 46), enter the new word, “(your name).”

Press this button

to save the newly

changed lyric

data.

Move the cursor

to the word

“star.”

To actually enter an edited

value, move the cursor away

from the value or press the

SONG [START/STOP] but-

ton.

The song “Twinkle Twinkle

Little Star” is in the folder

“For Children” in the Song

Book (page 75).

EXIT

Calls up the Main Filter

display. For more information

on each event type, refer to

the separate Data List booklet

(MIDI Data Format).

Enters checkmarks for all

items.

Reverses the checkmark

settings for all boxes. In

other words, this enters

checkmarks to all boxes that

were previously un-checked

and vice versa.

Calls up the Control

Change Filter display. For

more information on each

event type, refer to the

separate Data List booklet

(MIDI Data Format).

Calls up the Accompaniment

Filter display. For more

information on each event

type, refer to the separate

Data List booklet (MIDI Data

Format).

When “MAIN FILTER” or “ACCOMPANIMENT FILTER” is selected, these

select the item, scrolling up/down to the top or the bottom. When “CONTROL

CHANGE FILTER” is selected, these select the item, scrolling up/down eight

items at a time.

Selects the item, scrolling up/down one

item at a time.

Enters/removes the checkmark for the

selected item.

Selects only note data;

checkmarks for all other

boxes are removed.

Execute the settings

by pressing the

[EXIT] button.

END

109

CVP-205/203

Creating Accompaniment Styles — Style Creator

This powerful feature lets you create your own original styles, which can then be used for auto accompaniment — just

as with the preset styles.

About Creating Accompaniment Styles

The chart at right shows the basic parts (or “channels”) that make up each section

of an accompaniment style. To create an accompaniment style, record patterns to

the various channels one by one, for each of the sections you want to create.

■ Realtime Recording (page 111)

You can record accompaniment styles by simply playing the parts from the

keyboard in real time. However, you don’t have to record every part yourself

— you can choose an existing preset accompaniment style that is close to the

style you want, then add or replace parts in that style as needed to create your

own custom style.

Realtime Recording Characteristics

• Loop recording

Since auto accompaniment playback repeats the accompaniment patterns of several measures in a “loop,” you can

also record patterns in a loop. For example, if you start recording with a two-measure Main section, the two

measures are repeatedly recorded. Notes that you record will play back from the next loop (repetition), letting you

record new material while hearing the parts you previously recorded.

• Overdub recording

This feature lets you record new material to a track already containing recorded data, without deleting the original

data. In style recording, the recorded data remains intact, unless you speciﬁcally delete it yourself. For example, if

you start recording with a two-measure Main section, the two measures are repeated. As you record notes to each

pass of the loop (repetition), those notes play back from the next loop, letting you overdub new material while

hearing the previous parts.

■ Step Recording (page 112)

This method is like writing music notation on paper, since it allows you to enter each note or individually, and

specify its length. This is ideal for making precise recordings, or for recording parts that are difﬁcult to play.

■ Assembling an Accompaniment Style (page 113)

This convenient feature lets you create composite styles by combining

various patterns from the internal preset accompaniment styles. For

example, if you want to create your own original 8-beat style, you

could take rhythm patterns from the “8 Beat 1” style, use the bass

pattern from “8 Beat 2,” and import the chord patterns from the “60’s 8

Beat” style — combining the various elements to create one

accompaniment style.

■ Editing the created Accompaniment Style (page 114)

With the editing features, you can custom edit the styles you’ve

created by real time recording, step recording, and assembling from

other styles.

MIN

STYLE

ACMP

MAX

AUTO FILLIN

POWER

OFF

MASTER VOLUME

FADE IN / OUT

METRONOME

START STOP

OTS LINK

BREAK

INTRO

SONG

EXTRA TRACKS

(STYLE)

TRACK 2

(L)

TRACK 1

(R)

REC TOP START / STOP REW FF REPEAT GUIDE

NEW SONG

TEMPO

SYNC.START

RESET

MAIN

TAP TEMPO

TRANSPOSE

RESET

ENDING / rit. SYNC.STOP SYNC.START START / STOP

ABCD

DIRECT ACCESS

DEMO

HELP

FUNCTION

DIGITAL

STUDIO

SOUND

CREATOR

DIGITAL

RECORDING

MIXING

CONSOLE

BALANCE

PART

CHANNEL

ON / OFF

12345678

EXIT

BACK NEXT

VOICE PART

ON / OFF

LAYER

LEFT

LCD

CONTRAST

ENTER

DATA

ENTRY

VOICE EFFECT

REVERB

VOICE

PIANO & HARPSI.

BRASS

MUSIC FINDER

PIANO

DSP VARIATION HARMONY / ECHO MONO LEFT HOLD

E.PI ANO ORGAN & ACCORDION PERCUSSION GUITAR BASS

WOODWIND

STRINGS CHOIR & PAD SYNTH. XG USER

ONE TOUCH SETTING

REGISTRATION MEMORY

FREEZE

MEMORY

12345678

1234

STYLE

ACMP

AUTO FILLIN

OTS LINK

BREAK

INTRO

MAIN

ENDING / rit. SYNC.STOP SYNC.START START / STOP

ABCD

DIGITAL

RECORDING

Section Channel

INTRO A - D

RHYTHM 1, RHYTHM 2,

BASS, CHORD 1,

CHORD 2, PAD,

PHRASE 1, PHRASE 2

MAIN A - D

FILL IN A - D

BREAK

ENDING A - D

For information on the part

structure of accompaniment

styles, see page 95.

Rhythm 1

Rhythm 2

Bass

Chord 1

Chord 2

Pad

Phrase 1

Phrase 2

8Beat 1

Rhythm 1

Rhythm 2

Bass

Chord 1

Chord 2

Pad

Phrase 1

Phrase 2

8Beat 2

Rhythm 1

Rhythm 2

Bass

Chord 1

Chord 2

Pad

Phrase 1

Phrase 2

60’s 8 Beat

Rhythm 1

Rhythm 2

Bass

Chord 1

Chord 2

Pad

Phrase 1

Phrase 2

Creating Accompaniment Styles — Style Creator

CVP-205/203

110

Style File Format

The Style File Format (SFF) combines all of

Yamaha’s auto accompaniment know-how into

a single uniﬁed format. By using the edit

functions, you can take full advantage of the

SFF format and freely create your own styles.

The chart at right indicates the process by

which the accompaniment is played back.

(This does not apply to the rhythm tracks.)The

basic or “source” pattern in the chart is the

original style data. This source pattern is

recorded using accompaniment style

recording (see below).

As shown in the chart at right, the actual

output of the accompaniment is determined by

various parameter settings and chord changes

(played in Auto Accompaniment section of the

keyboard) entered to this source pattern.

Source Pattern

1 Source Root (root note of basic chord)

2 Source Chord (type of basic chord)

Pitch Conversion

3 NTR (Note Transposition Rule)

4 NTT (Note Transposition Table)

Other Settings

5 High Key (threshold of the pitch

conversion)

6 Note Limit (soundable range)

7 RTR (Retrigger Rule; how the pitches of

the chord change)

Output

These are the patterns

recorded to the

accompaniment styles

(page 117).

This data is created by

chords played in the

Auto Accompaniment

section of the

keyboard (page 63).

These settings are

edited from the

PARAMETER display.

These parameters

determine how the

pitch of the source

pattern is converted

when you play chords

in the Auto

Accompaniment

section of the

keyboard (page 117).

Chord changes (in Auto Accompa-

niment section of the keyboard)

Operation

BACK NEXT

DIGITAL

STUDIO

SOUND

CREATOR

DIGITAL

RECORDING

MIXING

CONSOLE

PA RT

Select the desired accompaniment style

for editing. To record a new

accompaniment style from scratch, call

up the BASIC page in the Style Creator

display and select “New Style” by

pressing the [C] button.

Record and edit the

accompaniment style. For

details on the operations for

each display, refer to the

explanations starting on the next

page.

Use the [BACK]/[NEXT]

buttons to select the

various pages.

Press the [EXIT] button to

close the STYLE CREATOR

display.

END

Call up the Style display by pressing the [I]

(SAVE) button (in Assembly page: [J] button),

then save the recorded / edited data to the

USER or FLOPPY DISK page.

Creating Accompaniment Styles — Style Creator

111

CVP-205/203

You can use the Realtime Recording features to create your own accompaniment style — either from scratch or based

on the preset accompaniment data. The operations here apply to step 4 on page 110.

Realtime Recording — Basic

REC.... Channel is enabled for recording.

ON...... Channel is enabled for playback.

OFF .... Channel is muted.

Selects an empty style,

allowing you to create a

new style from scratch.

Calls up the display for changing the

tempo or beat (time signature).

To release or cancel the

selection, press the [1▼] -

[8▼] button corresponding to

the channel you wish to

cancel. As long as you

continue to hold down the [J]

button, you can toggle

between deleting and

restoring the selected data.

Releasing the [J] button

permanently deletes the

data. Before recording to one

of the non-rhythm channels

(BASS - PHR 2), make sure to

delete the existing data of the

appropriate channel.

Available only when the channel is set to

[RHY1] or [RHY2], this lets you delete

speciﬁc percussion sounds during

recording. Simultaneously hold down this

button and press the key corresponding to

the instrument you want to delete.

First, select the desired voice. Start recording by pressing the STYLE [START/

STOP] button.

The selected section of the style starts playing back. Since the rhythm pattern

loops repeatedly, you can record new sounds and notes on each pass while

listening to the pattern. Icons above the keys conveniently indicate the

percussion instruments assigned to the keys.

Stop recording by pressing the STYLE [START/STOP] button again.

With the REC CHANNEL display shown, close the display by pressing

the [EXIT] button.

END

If you’ve enabled Sync Start

(by pressing the SYNC.

START button), you can

start recording by simply

pressing a key on the key-

board.

Select the desired channel for recording by simultaneously holding down the [F] (REC CH) button and

pressing the appropriate [1▲▼] - [8▲▼] button.

Before recording to one of the non-rhythm channels (BASS - PHR 2), make sure to delete the existing data

of the appropriate channel. You can make other settings (see the box “Other Parameters in the BASIC

Display” on page 112) after closing the REC CHANNEL display by pressing the [EXIT] button. To call up the

REC CHANNEL display again, press the [F] (REC CH) button.

• Only Drum Kit/SFX Kit

can be selected for the

RHY 2 channel.

• For the non-rhythm chan-

nels (BASS - PHR 2), all

voices with the exception

of the Drum Kit/SFX Kit

can be selected.

When this button is pressed, “DELETE” will appear over

channels containing data. To delete data from a speciﬁc

channel, simultaneously hold down this button and press the

appropriate [1▲] - [8▲] button.

Creating Accompaniment Styles — Style Creator

CVP-205/203

112

With this method, you can create a style pattern by entering notes and other data individually, without having to

perform them in real time. The operations here apply to step 4 on page 110.

The actual recording process is the same as in Step Recording of songs (page 97), with the exception of the points described

below. You can also edit each event from the Edit page, and the editing process the same as in editing songs (page 106).

•

In song recording, the end mark position can be changed freely. However, it cannot be changed when creating

accompaniment styles. This is because the length of the accompaniment style is automatically ﬁxed according to the

selected section. For example, when creating an accompaniment style based on a four-measure section, the end mark

position is automatically set to the end of the fourth measure, and cannot be changed from the Step Record screen.

• When editing the data recorded on the Edit page, you can switch between the type of data you want to edit (event

data or control data). Press the [F] (TRACK EVT) button to switch between the Event display (Note, Control Change,

etc.) and the Control display (System Exclusive, etc.).

Make sure to set the record channel from another display (e.g., BASIC display; page 111) beforehand.

Other Parameters in the BASIC Display

[I] (SAVE) button

Calls up the Style display for saving the accompaniment style data.

[3▲▼][4▲▼] (Section) buttons

Determines the section to be recorded.

[5▲▼][6▲▼] (Pattern Length) buttons

Determines the length of the selected section’s pattern in measures (1 - 32). The Fill

In/Break section is ﬁxed at a length of one measure.

[D] (Execute) button

Executes the Pattern Length change.

Recording — Precautions

• The basic chord used for the accompaniment style is called the source chord. All

chords that play and the pitches that sound are derived from the source chord. When

recording the Main and Fill In sections (for a source chord of CM7), keep the

following points in mind:

* When recording to the Bass or Phrase channels, try to use only the recommended

notes; this will ensure that you can play various chords with the accompaniment

style and get optimum results. (Other notes may work, providing you use them as short passing tones.)

* When recording to the Chord or Pad channels, use only the notes of the CM7 chord; this will ensure that

you can play various chords with the accompaniment style and get optimum results. (Other notes may work,

providing you use them as short passing tones.)

The source chord is set by default to CM7; however, you can change this to any chord you prefer. Refer to the

section “Making Style File Format Settings – Parameter” on page 117.

• When recording Intro and Ending sections, you can ignore the source chord and use any notes or chord

progressions you like. In this case, if you set the NTR parameter to “ROOT TRANSPOSE” and NTT to

“HARMONIC MINOR” or “MELODIC MINER” (in the PARAMETER page), the normal pitch conversions that

would result from playing different chords are cancelled (for playback) — meaning that the accompaniment

pitch conversion will only occur for changes in the root note or major/minor shifts.

You can also select the

desired section for recording

by pressing the appropriate

panel button. Pressing one

of the Section buttons calls

up the SECTION display,

from which you can change

sections by using the [6▲▼]/

[7▲▼] buttons. To actually

enter the change, press the

[8▲] button. To select the Fill

In section, press the [AUTO

FILL IN] button.

CRC CRC

C = chord note

C, R = recommended note

Step Recording

Creating Accompaniment Styles — Style Creator

113

CVP-205/203

This convenient function lets you combine accompaniment elements — such as rhythm, bass, and chord patterns —

from existing styles, and use them to create your own original accompaniment styles. The operations here apply to step

4 on page 110.

Assembling an Accompaniment Style —Assembly

Selects the style section and

channel that will be copied to

the corresponding channels,

selected with the [A]-[D] and

[F]-[I] buttons above.

Determines the playback settings for each channel. You can

assemble the accompaniment style while the style section and

channel that will be copied are playing.

SOLO ........... Mutes all but the selected channel. RHYTHM

channels set to REC in the REC CHANNEL display

(page 111) are played back simultaneously.

ON ............... Plays back the selected channels. Any channels

set to ON in the REC CHANNEL display

(page 111) are played back simultaneously.

OFF .............. Mutes the selected channel. If the selected

channel is set to ON in the REC CHANNEL

display (page 111), OFF does not appear and is

not available.

These let you select the accompaniment style that

will be used for each channel of your original

style. Select the desired channel by pressing the

[A] – [D], [F] – [I] buttons and press the same

button to call up the Style screen, from which you

can select the accompaniment style.

After repeating steps 1 and 2

as desired, press the [J] (SAVE)

button to save the assembled

style data. From here, you can

store the settings of all

channels (RHYTHM1,

RHYTHM2, BASS, etc.) to a

single accompaniment style.

If you change the section and channel in steps

#1 and #2, the currently speciﬁed section and

channel are also changed. The channels

being recorded are also changed and record-

ing is stopped automatically.

The PLAY TYPE parameter affects only the

playback, and does not change the actual

accompaniment style data.

Creating Accompaniment Styles — Style Creator

CVP-205/203

114

Change the Rhythmic Feel — Groove and Dynamics

These versatile features give you a wide variety of tools for changing the rhythmic feel of your created accompaniment

style. The operations here apply to step 4 on page 110.

■ Groove

Groove parameters

Original Beat Speciﬁes the beats to which Groove timing is to be applied. In other words, if “8 Beat” is selected, Groove timing is

applied to the 8th notes; if “12 Beat” is selected, Groove timing is applied to 8th-note triplets.

Beat Converter Actually changes the timing of the beats (speciﬁed in the ORIGINAL BEAT parameter above) to the selected value. For

example, when ORIGINAL BEAT is set to “8 Beat” and BEAT CONVERTER is set to “12,” all 8th notes in the section are

shifted to 8th-note triplet timing. The “16A” and “16B” Beat Converter which appear when ORIGINAL BEAT is set to “12

Beat” are variations on a basic 16th-note setting.

Swing Produces a “swing” feel by shifting the timing of the back beats, depending on the ORIGINAL BEAT parameter above.

For example, if the speciﬁed ORIGINAL BEAT value is “8 Beat”, the Swing parameter will selectively delay the 2nd, 4th,

6th, and 8th beats of each measure to create a swing feel. The settings “A” through “E” produce different degrees of

swing, with “A” being the most subtle and “E” being the most pronounced.

Fine Selects a variety of Groove “templates” to be applied to the selected section. The “PUSH” settings cause certain beats to

be played early, while “HEAVY” settings delay the timing of certain beats. The numbered settings (2, 3, 4, 5) determine

which beats are to be affected. All beats up to the speciﬁed beat —but not including the ﬁrst beat — will be played early

or delayed (for example, the 2nd and 3rd beats, if “3” is selected). In all cases, “A” types produce minimum effect, “B”

types produce medium effect, and “C” types produce maximum effect.

Edit the Created Accompaniment Style

Use these to select the

desired edit operation.

Calls up the Style display and

lets you store the edited

accompaniment style data.

Executes the Groove operation. After

the operation is completed, this button

changes to [UNDO], letting you

restore the original data if you’re not

satisﬁed with the Groove results. The

Undo function only has one level; only

the previous operation can be undone.

Determines the settings for each of the

Groove parameters (see the list below).

Creating Accompaniment Styles — Style Creator

115

CVP-205/203

■ Dynamics

Dynamics parameters

Accent Type Selects the type of accent.

Strength

Determines how strongly the selected Accent Type (above) will be applied. The

higher the value, the stronger the effect.

Expand/Compress Expands or compresses the range of velocity values, around a central velocity

value “64.” Values higher than 100% expand the dynamic range, while values lower

than 100% compress it.

Boost/Cut Boosts or cuts all velocity values in the selected section/channel. Values above

100% boost the overall velocity, while values below 100% reduce it.

Use these to select the

desired edit operation.

Calls up the Style display

and lets you store the

edited accompaniment

style data.

Executes the Dynamics operation. After the

operation is completed, this button changes

to [UNDO], letting you restore the original

data if you’re not satisﬁed with the

Dynamics results. The Undo function only

has one level; only the previous operation

can be undone.

Determines the settings for each of the

Dynamics parameters (see the list

below).

Select the desired channel to which

Dynamics is to be applied.

Velocity is determined by

how strongly you play the

keyboard.

The more strongly you play

the keyboard, the higher the

velocity value and, hence,

the louder the sound.

Creating Accompaniment Styles — Style Creator

CVP-205/203

116

Editing the Channel Data

In this display, there are ﬁve different channel-related edit functions, including Quantize, for editing the recorded

accompaniment style data. The operations here apply to step 4 on page 110.

■ Quantize

Refer to page 103.

■ Velocity Change

Boosts or cuts the velocity of all notes in the speciﬁed channel (selected with the [1▲▼]/[2▲▼] (CHANNEL)

buttons), according to the speciﬁed percentage (selected with the [4▲▼]/[5▲▼] (BOOST/CUT) buttons).

■ Bar Copy

This function allows data to be copied from one measure or group of measures to another location within the

speciﬁed channel. Use the [4▲▼] (TOP) and [5▲▼] (LAST) buttons to specify the ﬁrst and last measures in the

region to be copied. Use the [6▲▼] (DEST) button to specify the ﬁrst measure of the destination location, to which

the data is to be copied.

■ Bar Clear

This function clears all data from the speciﬁed range of measures within the selected channel. Use the [4▲▼] (TOP)

and [5▲▼] (LAST) buttons to specify the ﬁrst and last measures in the region to be cleared.

■ Remove Event

This function lets you remove speciﬁc events from the selected channel. Use the [4▲▼] - [6▲▼] (EVENT) buttons

to select the desired event type to be removed.

See the explanations below.

Preset channel BASS-

PHRASE2 can not be

edited.

Creating Accompaniment Styles — Style Creator

117

CVP-205/203

Making Style File Format Settings —Parameter

This display provides a variety of style controls— such as determining how the pitch and sound of the recorded style

change when playing the chords in the left-hand range of the keyboard. For details about the relationship between the

parameters, refer to “Style File Format” on page 110. The operations here are the same as described in step 4 on page 110.

■ Source Root/Chord

These settings determine the original key of the source pattern (i.e., the key used when recording the pattern). The default

setting of CM7 (with a Source Root of “C” and a Source Type of“M7”), is automatically selected whenever the preset data

is deleted prior to recording a new style, regardless of the Source Root and Chord included in the preset data. When you

change Source Root / Chord from the default CM7 to another chord, the chord notes and recommended notes will also

change, depending on the newly selected chord type. For details on chord notes and recommended notes, see page 112.

■ NTR (Note Transposition Rule) and NTT (Note Transposition Table)

• NTR (Note Transposition Rule)

This determines the system for pitch conversion of the source pattern. Two settings are available.

Root Trans (Root Transpose)

When the root note is transposed, the pitch relationship between notes is maintained. For example, the notes C3,

E3 and G3 in the key of C become F3, A3 and C4 when they are transposed to F. Use this setting for channels that

contain melody lines.

Root Fixed

The note is kept as close as possible to the previous note range. For example, the notes C3, E3 and G3 in the key

of C become C3, F3 and A3 when they are transposed to F. Use this setting for channels that contain chord parts.

When NTR is set to “Root

Fixed” and NTT is set to

“Bypass,” the “Source

Root” and “Source Chord”

parameters are changed to

“Play Root” and “Play

Chord,” respectively. In this

case, you can change

chords and hear the result-

ing sound for all channels.

See the explanations below.

CRC CR CRC C RC CRC C CR CRC C CR

CCC CR

CCC C CR CCC C RC

CRC

RCR

CR CR

CR CCR

CCR

RRCCC

CC RC

CR CC

CR C CR

CC RC C

CCR

CR R RC

CCR

CCC

CRC

CCC C

CRC CR

CRC CC

CCC

CCCR

RCC

CCC

RCC

CRC CRR

CRC

RCC

CR CC CCR CR

CMaj

CM7

Caug Cm6

Cm7



5Cm7

Cm7

CmM7 CmM7

Cdim

Cdim7



Csus4

Csus2

C1+8

C1+5



CM7



C7aug

CM7aug

C7sus4



When the Source Root is C:

C = chord note

C, R = recommended

note

Creating Accompaniment Styles — Style Creator

CVP-205/203

118

• NTT (Note Transposition Table)

This sets the note transposition table for the source pattern. Six transposition types are available.

Bypass

No transposition.

Melody

Suitable for melody line transposition. Use this for melody channels such as Phrase 1 and Phrase 2.

Chord

Suitable for chord transposition. Use for the Chord 1 and Chord 2 channels, especially when they contain piano

or guitar-like chordal parts.

Bass

Suitable for bass line transposition. This table is basically similar to the Melody table above, but recognizes on-

bass chords allowed in the FINGERED ON BASS ﬁngering mode. Use this primarily for bass lines.

Melodic Minor

When the played chord changes from a major to a minor chord, this table lowers the third interval in the scale by

a semitone. When the chord changes from a minor to a major chord, the minor third interval is raised by a

semitone. Other notes are not changed.

Harmonic Minor

When the played chord changes from a major to a minor chord, this table lowers the third and sixth intervals in

the scale by a semitone. When the chord changes from a minor to a major chord, the minor third and ﬂatted sixth

intervals are raised by a semitone. Other notes are not changed.

■ High Key/Note Limit

• High Key

This sets the highest key (upper octave limit)

of the note transposition for the chord root

change. Any notes calculated to be higher

than the highest key are transposed down to

the octave just below the highest key. This

setting is effective only when the NTR

parameter (page 117) is set to “Root Trans.”

• Note Limit

This sets the note range (highest and lowest

notes) for voices recorded to the style

channels. By judicious setting of this range,

you can ensure that the voices sound as

realistic as possible — in other words, that no

notes outside the natural range are sounded

(e.g., high bass sounds or low piccolo

sound). The actual notes that sound are

automatically shifted to the set range.

■ RTR (Retrigger Rule)

These settings determine whether notes stop sounding or not and how they change pitch in response to chord

changes.

Stop

The notes stop sounding.

Pitch Shift

The pitch of the note will bend without a new attack to match the type of the new chord.

Pitch Shift to Root

The pitch of the note will bend without a new attack to match the root of the new chord.

Retrigger

The note is retriggered with a new attack at a new pitch corresponding to the next chord.

Retrigger To Root

The note is retriggered with a new attack at the root note of the next chord. However, the octave of the new note

remains the same.

C3-E3-G3

F3-A3-C4



2-A



2-C



3-F3-G



Example — When the highest key is F

Root changes

Notes played

E3-G3-C4

High Limit

Low Limit

F3-A3-C4



F3-G



3-C



Example — When the lowest note is C3 and the highest is D4

Root changes

Notes played

119

CVP-205/203

Adjust the Volume Balance and Changing Voices

— Mixing Console

Set up just like a real mixing console, this display gives you comprehensive control over

the sound.

You can call up additional basic mixing controls by using the [BALANCE] button and the [CHANNEL ON/OFF] button

(page 62).

■ About the parameters

• VOL/VOICE (Volume/Voice) (page 120)

This contains settings related to the volume and voice of each part/channel. Here you can also enable the Auto

Revoice feature — which automatically plays XG-compatible songs (page 152) with the rich and dynamic voices

that are exclusive to the CVP-205/203. This gives you much more authentic and realistic instrument sounds for your

song playback.

• FILTER (page 121)

These controls affect the tone quality of the voice, letting you add power, punch, or brightness to the sound.

• TUNE (page 121)

These give you various tuning controls.

• EFFECT (page 122)

These control the amount of effect applied to the sound.

Mixing Console

This set of controls lets you

adjust the balance of the

voices and their stereo posi-

tion, as well as the amount

of effect that is applied to

each voice.

MIN

STYLE

ACMP

MAX

AUTO FILLIN

POWER

OFF

MASTER VOLUME

FADE IN / OUT

METRONOME

START STOP

OTS LINK

BREAK

INTRO

SONG

EXTRA TRACKS

(STYLE)

TRACK 2

(L)

TRACK 1

(R)

REC TOP START / STOP REW FF REPEAT GUIDE

NEW SONG

TEMPO

SYNC.START

RESET

MAIN

TAP TEMPO

TRANSPOSE

RESET

ENDING / rit. SYNC.STOP SYNC.START START / STOP

ABCD

DIRECT ACCESS

DEMO

HELP

FUNCTION

DIGITAL

STUDIO

SOUND

CREATOR

DIGITAL

RECORDING

MIXING

CONSOLE

BALANCE

PART

CHANNEL

ON / OFF

12345678

EXIT

BACK NEXT

VOICE PART

ON / OFF

LAYER

LEFT

LCD

CONTRAST

ENTER

DATA

ENTRY

VOICE EFFECT

REVERB

VOICE

PIANO & HARPSI.

BRASS

MUSIC FINDER

PIANO

DSP VARIATION HARMONY / ECHO MONO LEFT HOLD

E.PI ANO ORGAN & ACCORDION PERCUSSION GUITAR BASS

WOODWIND

STRINGS CHOIR & PAD SYNTH. XG USER

ONE TOUCH SETTING

REGISTRATION MEMORY

FREEZE

MEMORY

12345678

1234

MIXING

CONSOLE

PART

Operation

MIXING

CONSOLE

PART

PANEL PART

Includes the keyboard-played parts (Main/

Layer, Left), accompaniment parts, song,

microphone input (CVP-205 only)

STYLE PART

Accompaniment parts

SONG CH 1 - 8

Channels 1 - 8 of song playback

SONG CH 9 -16

Channels 9 - 16 of song playback

Select the other Mixing Console pages by using the [BACK]/

[NEXT] buttons and set the desired parameters.

For information on the various parameters and settings and how

to use them, refer to the explanations starting on page 120.

From the MIXING CONSOLE display, press the button

repeatedly until the desired display is called up. Each press of the

button switches among the displays listed below.

You can quickly and easily

set all parts to the same

value for the same parame-

ter (except for the VOICE

parameter). Simulta-

neously hold down the [A] -

[J] button that corresponds

to the parameter you want

to change and use the [1] -

[8] buttons or the [DATA

ENTRY] dial to change the

value.

For details on parameters

related to the Sound Cre-

ator, see page 89.

Close the Mixing

Console display by

pressing the [EXIT]

button.

END

Adjust the Volume Balance and Changing Voices

— Mixing Console

CVP-205/203

120

The operations for this page apply to step 2 of the procedure on page 119.

Setting the Level Balance and Voice — Volume/Voice

SOUND

CREATOR

DIGITAL

RECORDING

MIXING

CONSOLE

BALANCE

PART

CHANNEL

ON / OFF

DIGITAL

STUDIO

Set this to ON to enable automatic replacement of

the XG voices (in XG song data) with the special

voices of the CVP-205/203. To use the normal XG

voice set, turn this off.

These let you select the voice of each part, and adjust the panpot and volume.

VOICE

Calls up the VOICE display, from which you can select the desired voice (page 55). When the

Style/Song part is selected, User voices cannot be selected.

PANPOT

Determines the stereo position of the selected voice or track. A setting of 0 pans the sound hard

left, while 64 is at center, and 127 is at hard right.

VOLUME

Determines the level of each channel, giving you ﬁne control over the balance of all the parts.

Selects the XG voices

to be replaced (voices

usually used when

playing back)

Selects the voices used to

replace the XG voices (when

SONG AUTO REVOICE is

set to ON).

Executes the settings and closes the

Auto Revoice Setup display.

Closes the Auto Revoice

Setup screen without

executing the settings.

Each press of this

button switches

among the various

parts/channels.

Use these to select the VOICE,

PANPOT, or VOLUME

parameter rows.

Allows you to

select the

speciﬁc voice to

be replaced.

PIANO and BASIC can be

called up simultaneously.

ALL REVOICE

Replaces all of the replaceable XG voices with the

rich and authentic voices of the CVP-205/203.

PIANO REVOICE

Replaces only the piano

voices.

BASIC REVOICE

Replaces only the

recommended voices that are

suitable for playing back the

song.

ALL NO REVOICE

All the voices are returned

to the original XG voices.

When changing the rhythm/

percussion voices (drum

kits, etc.) of the accompani-

ment style and song from

the VOICE parameter, the

detailed settings related to

the drum voice are reset,

and in some cases you may

be unable to restore the

original sound. In the case

of song playback, you can

restore the original sound

by returning to the begin-

ning of the song and playing

back from that point. In the

case of accompaniment

style play, you can restore

the original sound by select-

ing the same style again.

Keep in mind that using the

Revoice function may result

in unnatural or unexpected

sound, depending on the

particular song data.

When playing GM song data,

channel 10 (in the SONG

CH 9 - 16 page) can only be

used for a Drum Kit voice.

Adjust the Volume Balance and Changing Voices

— Mixing Console

121

CVP-205/203

The operations for this page apply to step 2 of the procedure on page 119.

PORTAMENTO TIME ............When the part is set to Mono (page 59, 90), this determines the Portamento time. The

higher the value, the longer the time it takes for the pitch to change. Portamento is only

applied when you play legato (playing the next note before releasing the previous one).

PITCH BEND RANGE ...........When the Pitch Bend or Glide effect is assigned to the pedal, this determines the range of

the pitch change in semitones.

OCTAVE................................Determines the range of the pitch change in octaves, over two octaves up or down.

TUNING...............................Determines the pitch of the instrument.

Changing the Tone of the Voice — Filter

For details about the Filter,

see page 91.

When a Natural voice is

selected, Harmonic and

Brightness cannot be

changed.

Be careful with these con-

trols. Depending on the

selected voice, extreme set-

tings may result in noise or

distortion.

DIGITAL

STUDIO

SOUND

CREATOR

DIGITAL

RECORDING

MIXING

CONSOLE

BALANCE

PART

CHANNEL

ON / OFF

Switches between the HARMONIC and BRIGHTNESS parameters.

HARMONIC .........Allows you to adjust the resonance effect

(see “Harmonic Content” on page 91).

BRIGHTNESS .....Determines the brightness of the sound by

adjusting the cutoff frequency (page 91).

Each press of this

button switches among

the various parts/

channels.

Changing Pitch-related Settings — Tune

Portamento is used to cre-

ate a smooth transition in

pitch from one note to the

next.

Switches among the available parameters: PORTAMENTO

TIME, PITCH BEND RANGE, OCTAVE, and TUNING.

These increase/decrease (transpose) the pitch in semitone units.

MASTER ... Transposes both the pitch of the keyboard and that of the song playback.

SONG........ Transposes the pitch of the song playback.

KBD ..........Transposes the pitch of the keyboard.

Refer to the explanation below.

When a Natural voice is

selected, Portamento Time

cannot be changed.

Adjust the Volume Balance and Changing Voices

— Mixing Console

CVP-205/203

122

The operations for this page apply to step 2 of the procedure on page 119.

Adjusting the Effects

There are three effect sec-

tions: Reverb, Chorus, and

DSP (which contains a vari-

ety of effect types). These

are available independently

for the Natural voices and

Regular voices. For details,

refer to the Effect Block list

(page 123).

DIGITAL

STUDIO

SOUND

CREATOR

DIGITAL

RECORDING

MIXING

CONSOLE

BALANCE

PART

CHANNEL

ON / OFF

Switches among the

effect sections:

REVERB, CHORUS,

and DSP.

Determines the amount of effect that is applied to each part. For more information

about the characteristics of each effect, see the Effect Block list on page 123.

Press this to edit and store

the effect (page 122, 123).

These determine the effect block and let you assign the effect.

BLOCK............Determines the effect block (group of similar or related effects).

PART ............... Determines the part to which the Insertion effect is applied. It is effective only

when the block is set to “DSP1” and the CONNECTION parameter is set to

“Insertion” (page 123).

CATEGORY..... The various effect programs (in Type below) are grouped into categories.

This parameter may not be available depending on the selected block.

TYPE ............... Determines the type of effect that is assigned to the selected effect block.

The actual effect types that are available may differ depending on the

selected block.

When the BLOCK parameter is set to REVERB1, CHORUS1, or

DSP1, press this to call up the display from which you can change the

detailed settings for the effects.

Each press of this

button switches

among the various

parts/channels.

Indicates the type name for each effect block.

Adjust the Volume Balance and Changing Voices

— Mixing Console

123

CVP-205/203

Effect Block

Block Parts Characteristics

Number of User Effect

REVERB 1

(for Regular Voices)

All parts

Reproduces the warm ambience of playing in

a concert hall or jazz club.

REVERB 2

(for Natural Voices)

All parts except microphone (MIC) —

CHORUS 1

(for Regular Voices)

All parts

Produces a rich “fat” sound as if several parts

are being played simultaneously.

CHORUS 2

(for Natural Voices)

All parts except microphone (MIC) —

DSP 1

(for Regular Voices)

Main, Layer, Left, Song (Ch. 1 - 16),

MIC

In addition to reverb and chorus effects, this

section features a variety of special effects,

including distortion.

DSP 2

(for Natural Voices)

All parts except microphone (MIC) —

BRILLIANCE (CVP-205 only)

(for Natural Voices)

All parts except microphone (MIC)

Changes the brightness and clarity of the

sound.

—

Determines the effect block.

Calls up the

display for storing

the effect.

Determines the effect category.

Determines the effect type.

Determines the effect parameter to be adjusted.

Determines the level of the

effect (return level). This is

not available when BLOCK

is set to “DSP1,”

PARAMETER is set to

“CONNECTION,” and

VALUE is set to “Insertion.”

Determines the value of the

selected parameter.

Calls up the display

for naming the User

Effect (page 46).

Select the destination to which the effect is to be stored.

The number of memory spaces available for the destination

differs for each block (refer to the chart below).

Stores the effect settings you

made above to a User Effect

location (SYSTEM) for future

recall. To call up the effect, select

USER from the CATEGORY

parameter and select the desired

effect from the TYPE parameter.

Keep in mind that in some

cases noise may result if

you adjust the effect param-

eters while playing the

instrument.

This parameter cannot be

set when BLOCK is set to

“REVERB2,” “CHORUS2,”

or “DSP2” (or “BRIL-

LIANCE”; CVP-205 only).

Switches between

the upper/lower

parameters. For the

lower parameter, the

depth can be

changed when the

[VARIATION] button

is on.

Adjust the Volume Balance and Changing Voices

— Mixing Console

CVP-205/203

124

Effect Structure

The CVP-205/203 features the following digital effect systems, which can be applied independently for the Natural

voices (page 89) and the Regular voices (page 89). The effect type, depth, and various parameters can be set with the

panel controls.

• Reverb .......... Normally the settings that ﬁt the selected style are called up. For most of the Natural voices, settings

that ﬁt the voice are called up.

• Chorus.......... Normally the settings that ﬁt the selected style are called up. For most of the Natural voices, settings

that ﬁt the voice are called up.

• DSP .............. Normally the settings which ﬁt the selected voice are called up. Variation (settings in which the

expression of the effect is changed) is prepared for each type, and it can be turned ON/OFF by the

[VARIATION] button on the panel.

When the Natural voice is selected, the [VARIATION] button does not work.

The illustration below shows how the various effect blocks are set up and traces the signal ﬂow for the send/return

controls set on the CVP-205/203.

For Natural Voices (REVERB2, CHORUS2, DSP2)

For Regular Voices (REVERB1, CHORUS1, DSP1)

OUT

Rev Send

MAIN VOICE

Dry

Cho Send

DSP Send

When DSP is set as an Insertion effect

(here, PART is set to MAIN),

it is put here in the signal flow.

(For Natural voices,

DSP can only be used

as a System effect.)

Rev Send

LAYER VOICE

Dry

Cho Send

DSP Send

Rev Send

LEFT VOICE

Dry

Cho Send

DSP Send

Rev Send

MIC

(CVP-205 only)

Dry

Cho Send

DSP Send

Rev Send

Dry

Cho Send

DSP Send

CHORUS

BRILLIANCE

REVERB

DRY LINE

DSP

Chorus

Return

DSP

Return

Reverb

Return

DSP

When DSP is set as a System effect,

it is put here in the signal flow.

(For Natural voices, DSP can only

be used as a System effect.)

(CVP-205 Natural Voices only)

STYLE/SONG

(each channel)

125

CVP-205/203

Making Global and Other Important Settings — Function

The Function mode gives you access to various advanced functions related to the instrument as a whole. These

sophisticated functions let you customize the Clavinova to your own musical needs and preferences.

Adjusting the Pitch and Tuning — Master Tune and Scale Tune

■ Master Tune (page 127)

This allows you to make ﬁne adjustments to the overall pitch of the instrument — letting you accurately match the

tuning with that of other instruments.

■ Scale Tune (page 127)

This determines the particular tuning system (or temperament) for the instrument. This is especially useful for playing

period pieces, to match the tuning system used during speciﬁc musical eras.

Setting Song-related Parameters — Song Settings (page 129)

These allow you to set parameters related to song playback as well as the practice function types.

Setting Auto Accompaniment-related Parameters — Style Setting, Split Point, and Chord

Fingering

■ Style Setting / Split Point (page 130)

These determine the auto accompaniment-related settings, and let you set the split point.

■ Chord Fingering (page 131)

This determines the method for playing/indicating chords when using the auto accompaniment features. You can

even check how to play the chord, since the individual notes are indicated in the display.

MIN

STYLE

ACMP

MAX

AUTO FILLIN

POWER

OFF

MASTER VOLUME

FADE IN / OUT

METRONOME

START STOP

OTS LINK

BREAK

INTRO

SONG

EXTRA TRACKS

(STYLE)

TRACK 2

(L)

TRACK 1

(R)

REC TOP START / STOP REW FF REPEAT GUIDE

NEW SONG

TEMPO

SYNC.START

RESET

MAIN

TAP TEMPO

TRANSPOSE

RESET

ENDING / rit. SYNC.STOP SYNC.START START / STOP

ABCD

DIRECT ACCESS

DEMO

HELP

FUNCTION

DIGITAL

STUDIO

SOUND

CREATOR

DIGITAL

RECORDING

MIXING

CONSOLE

BALANCE

PAR T

CHANNEL

ON / OFF

12345678

EXIT

BACK NEXT

VOICE PART

ON / OFF

LAYER

LEFT

LCD

CONTRAST

ENTER

DATA

ENTRY

VOICE EFFECT

REVERB

VOICE

PIANO & HARPSI.

BRASS

MUSIC FINDER

PIANO

DSP VARIATION HARMONY / ECHO MONO LEFT HOLD

E.PI ANO ORGAN & ACCORDION PERCUSSION GUITAR BASS

WOODWIND

STRINGS CHOIR & PAD SYNTH. XG USER

ONE TOUCH SETTING

REGISTRATION MEMORY

FREEZE

MEMORY

12345678

1234

FUNCTION

Operation

DEMO

HELP

FUNCTION

Select the desired function.

Set the parameters of the selected

function.

The operations for each function are

covered in the following explanations.

To return to the previous

display, press the [EXIT]

button.

END

Making Global and Other Important Settings — Function

CVP-205/203

126

Making Settings for the Pedals and

Keyboard — Controller

■ Pedal (page 131)

These settings determine how the connected pedals

(including foot controllers and footswitches) are used.

They can be assigned to a variety of functions, letting

you control operations with your feet — such as

turning the accompaniment style on/off, or triggering

Fill In patterns.

■ Keyboard / Panel (page 133)

These settings determine the touch sensitivity of the

keyboard (how touch affects volume), and let you

independently transpose the keyboard, song data,

and the entire instrument.

Setting the Registration Sequence, Freeze,

and Voice Set

■ Registration Sequence (page 134)

This determines the order in which the Registration

Memory presets (1 - 8) are called up — by using the

[BACK][NEXT] buttons or the pedal.

■ Freeze (page 134)

This lets you specify the settings you want to be

maintained or left unchanged, even when changing

Registration Memory presets.

■ Voice Set (page 135)

This lets you determine whether certain voice-related

settings (such as Effects, EQ, Harmony, etc.) are

automatically called up or not when you select a

voice.

Setting Harmony and Echo (page 135)

These let you set the type of Harmony or Echo effect

applied to the keyboard-played voices, as well as the

amount of effect.

Showing the Clavinova Display on a TV —

Video Out (CVP-205 only) (page 136)

These settings determine the display characteristics when

outputting the CVP-205’s display contents to a TV

monitor (connected to the VIDEO OUT terminal). You

can set the size and color of the displayed characters, as

well as the color of the display background.

Making MIDI Settings

■ System (page 137)

These determine various system messages settings

(such as Clock, Start/Stop, System Exclusive), as well

as Local Control on/off.

■ Transmit (page 138)

This determines how playback data is sent to

connected MIDI devices — i.e., which parts are

assigned to which MIDI Transmit channels. This also

lets you specify the type of data to be transmitted over

each channel.

■ Receive (page 139)

This determines how the parts of the CVP-205/203

respond to data from connected MIDI devices — i.e.,

which parts are assigned to which MIDI Receive

channels. This also lets you specify the type of data to

be received over each channel.

■ Root (page 139)

This determines the channel(s) recognized for the root

notes, for use with the auto accompaniment.

■ Chord Detect (page 139)

This determines the channel(s) recognized for the

chords, for use with the auto accompaniment.

Other Settings — Utility

■ Conﬁg 1 (page 140)

This page contains settings for Fade In/Out,

Metronome, Parameter Lock, and the Tap sound.

■ Conﬁg 2 (page 141)

From this page, you can adjust the display, make

speaker settings, and change the voice number

indication.

■ Disk (page 142)

From this page, you can format disks, and copy from

disk to disk.

■ Owner (page 143)

From this page, you can set the language of the

instrument, and input your own name — which is

shown automatically every time the power is turned

on.

■ System Reset (page 143)

This function restores the CVP-205/203 to its original

factory settings. You can also specify which types of

settings are to be restored, as well as store your own

original settings for future recall.

Making Global and Other Important Settings — Function

127

CVP-205/203

The explanations here apply to step #3 of the procedure on page 125.

Tuning the Overall Pitch — Master Tune

Selecting a Scale — Scale Tune

Fine Tuning the Pitch/Selecting a Scale — Master Tune/Scale Tune

Hz (Hertz)

This unit of measurement

refers to the frequency of a

sound, and represents the

number of times a sound

wave vibrates in a second.

The Tune function does not

affect the Drum Kit or SFX

Kit voices.

Determines the overall pitch of the CVP-205/

203, from 414.8 - 466.8 Hz. Press the 4 or 5

[▲▼] buttons simultaneously to instantly reset

the value to the factory setting of 440.0 Hz.

Determines the Scale (page 128).

Determines the note to be tuned and the amount of tuning.

The tuning range is from “-64” through “0” to “+63.” Each increment

equals one cent (one “cent” is one hundredth of a semitone).

Determines the ﬁne tuning of the selected note in 1-

cent steps. Press the 5 or 6 [▲▼] buttons

simultaneously to instantly reset the value to the

factory setting.

Determines the base note for each

scale.

When the base note is changed, the

pitch of the keyboard is transposed, yet

maintains the original pitch relationship

between the notes.

The current tuning of each note is shown above or

below the corresponding key.

Cent

A unit of pitch equal to 1/100

of a semitone (100 cents = 1

semitone).

You can register your origi-

nal scale tunings to a REG-

ISTRATION MEMORY

button. To do this, check-

mark “SCALE” in the REG-

ISTRATION MEMORY

display (page 85).

Making Global and Other Important Settings — Function

CVP-205/203

128

Scale

■ Equal Temperament

The pitch range of each octave is divided equally into twelve parts, with each half-step evenly spaced in pitch. This

is the most commonly used tuning in music today.

■ Pure Major/Pure Minor

These tunings preserve the pure mathematical intervals of each scale, especially for triad chords (root, third, ﬁfth).

You can hear this best in actual vocal harmonies — such as choirs and acapella singing.

■ Pythagorean

This scale was devised by the famous Greek philosopher and is created from a series of perfect ﬁfths, which are

collapsed into a single octave. The 3rd in this tuning are slightly unstable, but the 4th and 5th are beautiful and

suitable for some leads.

■ Mean-Tone

This scale was created as an improvement on the Pythagorean scale, by making the major third interval more “in

tune.” It was especially popular from the 16th century to the 18th century. Handel, among others, used this scale.

■ Werckmeister/Kirnberger

This composite scale combines the Werckmeister and Kirnberger systems, which were themselves improvements on

the mean-tone and Pythagorean scales. The main feature of this scale is that each key has its own unique character.

The scale was used extensively during the time of Bach and Beethoven, and even now it is often used when

performing period music on the harpsichord.

■ Arabic

Use these tunings when playing Arabic music.

Pitch settings for each scale (in cents; example scale of C)

The values shown in this chart are actually rounded off to the nearest whole number for use on the instrument.





EFF





Equal Temperament 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0

Pure Major 0.0 -29.7 3.9 15.6 -14.1 -2.3 -9.4 2.3 -27.3 -15.6 18.0 -11.7

Pure Minor 0.0 33.6 3.9 15.6 -14.1 -2.3 31.3 2.3 14.1 -15.6 18.0 -11.7

Pythagorean 0.0 14.1 3.9 -6.3 7.8 -2.3 11.7 2.3 15.6 6.3 -3.9 10.2

Mean-Tone 0.0 -24.2 -7.0 10.2 -14.1 3.1 -20.3 -3.1 -27.3 -10.2 7.0 -17.2

Werckmeister 0.0 -10.2 -7.8 -6.3 -10.2 -2.3 -11.7 -3.9 -7.8 -11.7 -3.9 -7.8

Kirnberger 0.0 -10.2 -7.0 -6.3 -14.1 -2.3 -10.2 -3.1 -7.8 -10.2 -3.9 -11.7

Arabic1 0.0 0 -50.0 0.0 0.0 0.0 0.0 0.0 0.0 -50.0 0.0 0.0

Arabic2 0.0 00.0 0.0 -50.0 0.0 0.0 0.0 0.0 0.0 0.0 -50.0

Making Global and Other Important Settings — Function

129

CVP-205/203

The explanations here apply to step #3 of the procedure on page 125.

Setting Song-related Parameters — Song Settings

Quick Start

On some commercially avail-

able song data, certain set-

tings related to the song

(such as voice selection, vol-

ume, etc.) are recorded to

the ﬁrst measure, before the

actual note data. When

Quick Start is set to “ON,”

the CVP-205/203 reads all

initial non-note data of the

song at the highest possible

speed, then automatically

slows down to the appropri-

ate tempo at the ﬁrst note.

This allows you to start play-

back as quickly as possible,

with a minimum pause for

reading of data.

Channel

Refers to the MIDI channel

(page 150). The channels

are assigned as follows:

Song

1 - 16

Accompaniment Style

9 - 16

The guide lamps light in

response to song channel

assigned to Tracks 1 and 2,

as well as chord data (when

contained in the song). Nor-

mally, you can leave the

AUTO SET CH function set

to ON, and the song channel

will automatically be set. If

the results aren’t satisfac-

tory, you’ll need to match the

Channel Setting "TRK1 CH"

and "TRK2 CH" parameters

to the appropriate right- and

left-hand parts.

Phrase Mark

This data speciﬁes a certain

location in the song data. In

the included “Music Software

Collection” songs (CVP-203

only), these are indicated by

numbers (1, 2, etc.) in the

score.

Determines the Guide

method.

Turns guide lamps ON or

OFF.

Determines the timing for the guide

lamps.

JUST ........ The guide lamps light

precisely at the moment

you should play.

NEXT ........ The guide lamps light just

before the moment you

should play. If you miss the

proper timing, the guide

lamps ﬂash.

Turns Quick Start on/off (see note).

Allows you to play back all songs

from the same folder continuously.

Determines the MIDI channel assigned

to the [TRACK2] button.

Determines the MIDI channel assigned

to the [TRACK1] button.

When set to “ON,” this

automatically sets the proper

Track 1 and Track 2 channels for

use with the practice functions.

Normally, this should be set to

“ON.”

Determines the language of the

displayed lyrics.

When this is set to “AUTO,” the

language defaults to that of the

song data. When not set to

“AUTO,” the language defaults to

Japanese, when the internal

setting (page 143) is

“JAPANESE”; for all other

languages, this is set to

“INTERNATIONAL.”

Determines whether the Phrase

Mark Repeat function for the song

is on or off. When this is on, you

can repeatedly play back a

speciﬁed phrase (selection of

measures) of the song. The

method for setting a phrase mark

is the same as that in the SONG

POSITION display (page 77).

Making Global and Other Important Settings — Function

CVP-205/203

130

The explanations here apply to step #3 of the procedure on page 125.

Setting Auto Accompaniment-related Parameters — Style Setting

and Split Point

Setting Auto Accompaniment-related Parameters —

Style Setting, Split Point, and Chord Fingering

These select the part to which the split point

setting is applied: accompaniment, left-hand

range, or both. Press the desired key for the split

point while holding down one of these buttons.

The pressed key is included in the range for the

Auto Accompaniment section of the keyboard

(ACMP) or the left-hand range (LEFT).

A+L (ACMP + LEFT)

Allows you to simultaneously set the split

point for both the left-hand range and the

Auto Accompaniment section of the

keyboard.

Turns the Stop Accompaniment (ACMP) function on/off. When this is set to “ON,”

you can play the chord and bass sounds of the accompaniment by playing chords

— even when the accompaniment style is not playing back.

This applies to the OTS Link function, in which One Touch Settings are automatically called up

with changes in the section. This determines the timing in which the One Touch Settings change

with the section. (The [OTS LINK] button must be on.)

Real Time

One Touch Setting is immediately called up when you press a section button.

Next Bar

One Touch Setting is called up at the next measure, after you press a section button.

The CVP-205/203 lets you automatically enable Sync Stop (page 66) simply by

quickly pressing/releasing keys in the Auto Accompaniment section of the

keyboard. This parameter lets you set the length of the key-hold time.

Turns touch response for the accompaniment on/off. When this is set to “ON,”

the accompaniment volume changes in response to your playing strength (in

the Auto Accompaniment section of the keyboard).

Determines the default section that is automatically called up when selecting

different accompaniment styles (when accompaniment is stopped).

Determines the split points for the auto accompaniment (ACMP) and the left-

hand range (LEFT). The same value can be set for both or for each

independently, using buttons [F], [G], and [H] (see above). You can use these

buttons by themselves to set the split point value.

About Section Set

When any of the Main A-D

sections is not included in

the accompaniment style

data, the nearest section is

automatically selected. For

example, when Main D is not

contained in the selected

accompaniment style, Main

C will be called up.

L (LEFT)

Allows you to set the split point for the left-hand range of the keyboard.

A (ACMP)

Allows you to set the split point for the Auto Accompaniment section of the

keyboard.

About Section Set

When any of the Main A-D

sections is not included in

the accompaniment style

data, the nearest section is

automatically selected. For

example, when Main D is not

contained in the selected

accompaniment style, Main

C will be called up.

Split point can be set in the

MAIN display.

About Split Point

Split point is the position on keyboard that separates the Auto

Accompaniment section (ACMP) and left-hand section (LEFT) from the

right-hand section (MAIN). The LEFT split point cannot be set lower than

the ACMP split point, and the ACMP split point cannot be set higher than

the LEFT split point.

Split point (A) Split point (L)

Split point (A) + (L)

Auto

Accompaniment

section

Auto Accompaniment section

+ Left-hand section

Left-hand

section

Right-hand

section

Right-hand

section

Making Global and Other Important Settings — Function

131

CVP-205/203

Setting the Fingering Method — Chord Fingering

This determines how the notes you play on the keyboard indicate or play the chords of the accompaniment. To learn

how to play certain chords, use the convenient Chord Tutor function (see note below).

The explanations here apply to step #3 of the procedure on page 125.

Making Settings for the Pedals

Determines the ﬁngering

type (page 63).

This lets you change the root

note from the chord.

This lets you change the

chord type.

Indicates the note that belongs to a

chord in the music.

Indicates the note that

belongs to a chord. Some

notes can be omitted. The

chord name is indicated

next to “CHORD NAME.”

...Required

...Can be omitted

...Either note can be

omitted

...Can be omitted when

the note indicated by

is omitted

The chord indication in the

display applies to the Fin-

gered method, regardless if

another method is actually

selected.

Chord Tutor

The Chord Tutor feature is

essentially an electronic

“chord book” that shows you

appropriate ﬁngerings for

chords; it is useful when you

want to play certain chords.

Simply specify the desired

chord via the [6▲▼] - [8▲▼]

buttons, and the ﬁngerings

for the Fingered method are

indicated in the display.

Making Settings for the Pedals and Keyboard — Controller

Determines the particular

pedal to which a function is

to be assigned.

Determines the function to be

assigned to the selected pedal. Any

one of the available functions can be

assigned to each pedal.

For information on the assignable

functions, see “Pedal-controllable

Functions” on page 132.

If necessary, you can turn

the corresponding part ON/

OFF or set the control depth

(see the next page).

Pedal on/off operation may

differ depending on the

particular pedal you’ve

connected to the [AUX

PEDAL] jack. For example,

pressing down on one pedal

may turn the selected

function on, while pressing

a different make/brand of

pedal may turn the function

off. If necessary, use this

setting to reverse the

operation.

Making Global and Other Important Settings — Function

CVP-205/203

132

Pedal-controllable Functions

* For best results, use the optional Yamaha FC7 Foot Controller.

The parameters below correspond to buttons [2▲▼] - [8▲▼], and their availability depends on the selected control Type. For example, if

SUSTAIN is selected as the Type, the parameters “HALF PEDAL POINT”, “MAIN”, “LAYER” and “LEFT” automatically appear in the display.

* For best results, use the optional Yamaha FC7 Foot Controller.

VOLUME* Allows you to use a foot controller (AUX pedal only) to control the volume.

SUSTAIN When the pedal is pressed notes played have a long sustain. Releasing the pedal immediately stops (damps) any

sustained notes.

SOSTENUTO If you press and hold the pedal here, only the ﬁrst note will be sustained (the note that you played and held when pressing

the pedal). This makes it possible to sustain a chord, for example, while other notes are played staccato.

SOFT Pressing the pedal subtly reduces the volume and slightly changes the timbre of notes played. It only applies to certain

voices — PIANO, for example.

GLIDE When the pedal is pressed the pitch changes, and then back to normal pitch when the pedal is released.

PORTAMENTO The portamento effect (a smooth slide between notes) can be produced while the pedal is pressed. Portamento is

produced when notes are played legato style (i.e., a note is played while the preceding note is still held). The portamento

time can be set via the Mixing Console display (page 121). It does not work for Natural voices.

PITCHBEND*

Bend notes up or down while pedal is pressed. This can only be set to the AUX pedal and the CVP-205’s damper pedal.

MODULATION* Applies a vibrato effect to notes played on the keyboard. The depth of the effect increases while pedal is pressed. This

does not work for the Natural voices.

DSP VARIATION Same as the [VARIATION] button. This does not work for the Natural voices.

VIBROTOR ON/OFF Turns the “VibRotor” effect type (page 122) on and off. This only works for the Natural voices.

HARMONY/ECHO Same as the [HARMONY/ECHO] button.

SCORE PAGE+ (CVP-205 only)

While the song is stopped, you can turn to the previous score page (one page only).

SCORE PAGE- (CVP-205 only)

While the song is stopped, you can turn to the next score page (one page only).

SONG START/STOP Same as the SONG [START/STOP] button.

STYLE START/STOP Same as the STYLE [START/STOP] button.

TAP TEMPO Same as the [TAP TEMPO] button.

SYNCRO START Same as the [SYNC. START] button.

SYNCRO STOP Same as the [SYNC. STOP] button.

INTRO Same as the [INTRO] button.

MAIN A Same as the [MAIN A] button.

MAIN B Same as the [MAIN B] button.

MAIN C Same as the [MAIN C] button.

MAIN D Same as the [MAIN D] button.

FILL DOWN A ﬁll-in plays, automatically followed by the Main section of the button on the immediate left.

FILL SELF Fill-in starts playing.

BREAK Break starts playing.

FILL UP A ﬁll-in plays, automatically followed by the Main section of the button on the immediate right.

ENDING Same as the [ENDING/rit.] button.

FADE IN/OUT Same as the [FADE IN/OUT] button.

FING/ON BASS The pedal alternately switches between the Fingered and On Bass modes (page 63).

BASS HOLD While the pedal is pressed, the Accompaniment Style bass note will be held even if the chord is changed. If the ﬁngering

is set to “FULL KEYBOARD,” the function does not work.

PERCUSSION

The pedal plays a percussion instrument selected by the [4

▲▼] - [8▲▼] buttons. You can use the keyboard to select the

desired percussion instrument.

LAYER ON/OFF Same as the [LAYER] button.

LEFT ON/OFF Same as the [LEFT] button.

OTS+ Calls up the next One Touch Setting.

OTS- Calls up the previous One Touch Setting.

SONG, STYLE, MIC (CVP-205

only), LEFT, LAYER, MAIN

These specify the part(s) that will be affected by the pedal.

HALF PEDAL POINT* You can specify how far down you should press on the right pedal until the damper effect (page 59) starts working. This

can be set for certain kinds of pedals, such as the AUX pedal (YAMAHA FC7) or the CVP-205’s damper pedal.

DEPTH Determines the depth of the left pedal effect, when SOFT is selected. This only works for the Natural voices.

UP/DOWN

When GLIDE or PITCH BEND is selected, this determines whether the pitch change goes up (is raised) or down (is lowered).

RANGE When GLIDE or PITCH BEND is selected, this determines the range of the pitch change, in semitones.

ON SPEED When GLIDE is selected, this determines the speed of the pitch change, when the pedal is pressed.

OFF SPEED When GLIDE is selected, this determines the speed of the pitch change, when the pedal is released.

KIT When PERCUSSION is assigned to the pedal, all available drum kits are shown here, letting you select the particular

drum kit used for the pedal.

PERCUSSION When PERCUSSION is assigned to the pedal, all sounds of the selected drum kit (in KIT above) are shown here. This

determines the particular instrument sound assigned to the pedal.

Making Global and Other Important Settings — Function

133

CVP-205/203

Changing the Touch Sensitivity and Transpose — Keyboard/Panel

Keyboard Touch

The Touch feature lets you control the volume of the voices by your playing strength. These settings allow you to

customize the keyboard’s touch response (sensitivity) to your personal playing preferences.

Transpose Assign

This determines which aspect of the instrument is affected by the [TRANSPOSE] button.

HARD 2

Requires strong playing to produce

high volume. Best for players with a

heavy touch.

HARD 1

Requires moderately strong playing for

higher volume.

NORMAL

Standard touch response.

SOFT 1

Produces high volume with moderate

playing strength.

SOFT 2 Produces relatively high volume even

with light playing strength. Best for

players with a light touch.

Determines the

Touch sensitivity

setting (refer to the

table at right).

Determines the

ﬁxed volume level

when Touch is set

to “OFF.”

Determines whether touch is on or not for the corresponding parts.

The TOUCH setting affects all voices globally. Keep

in mind that you can set each voice to a different

touch sensitivity (TOUCH SENSE). For example, to

play a pipe organ voice most authentically, you can

set this so that the voice is not affected by touch

(page 90).

KEYBOARD

For this setting, Transpose affects the pitch of the

keyboard-played voices (Main, Layer, and Left) and

the accompaniment styles.

SONG

For this setting, Transpose affects only the pitch of

the songs.

MASTER

For this setting, Transpose affects the pitch of the

entire instrument (keyboard voices,

accompaniment styles, and songs).

Transpose

Allows you to shift the pitch of the keyboard-played voices,

accompaniment style playback, and song data in semitone

units.

Press one of the [TRANSPOSE] buttons.

A TRANSPOSE pop-up window, selected via

TRANSPOSE ASSIGN, appears.

Adjust the value by using the [TRANSPOSE] buttons.

Close the TRANSPOSE windows by pressing the

[EXIT] button.

• Selectively Transposing Keyboard/Song

These settings can be used to match both the song and your

keyboard performance to a certain key. For example, let’s

say you wish to play and sing along with a certain recorded

song. The song data is in F, but you feel most comfortable

singing in D, and you are accustomed to playing the

keyboard part in C. To match up the keys, keep the Master

Transpose setting at “0,” set the Keyboard Transpose to “2,”

and set Song Transpose to “-3.” This brings the keyboard part

up in pitch and the song data down to your comfortable

singing key.

TRANSPOSE

RESET

END

The transpose function

does not affect the Drum

Kit or SFX Kit voices.

Making Global and Other Important Settings — Function

CVP-205/203

134

The explanations here apply to step #3 of the procedure on page 125.

Specifying the Order for Calling Up Registration Memory Presets —

Registration Sequence

You can save your custom panel settings to the Registration Memory presets, and call them up by pressing the

appropriate REGISTRATION MEMORY buttons [1] - [8]. The convenient Registration Sequence function lets you call up

the presets in any order you specify, by simply using the [BACK]/[NEXT] buttons or the pedal as you play.

Maintaining Panel Settings — Freeze

This lets you specify the settings you want to be maintained or left unchanged, even when changing Registration

Memory presets. For details, see page 87.

Setting the Registration Sequence, Freeze, and Voice Set

Turns the Registration

Sequence function

on/off. When this is

set to “ON,” the

programmed

Registration

Sequence is shown at

the top right of the

Main display, and you

can step through the

sequence in this

display by using the

[BACK]/[NEXT]

buttons or the pedals.

Determines which pedal is used to advance

(increment) through the sequence.

Determines which

pedal is used to

reverse (decrement)

through the sequence.

Determines how Registration

Sequence behaves when

reaching the end of the

sequence.

Stop

Pressing the [NEXT] button or

the “advance” pedal has no

effect. The sequence is

“stopped.”

Top

The sequence starts again at

the beginning.

Next Bank

The sequence automatically

moves to the beginning of the

next Registration Memory bank

in the same folder.

Indicates the ﬁle name of the selected

Registration Memory bank.

Indicates the Registration Memory preset

numbers, in the order of the current

Registration Sequence.

These move the cursor position in the sequence.

Replaces the number at the cursor position with the

currently selected Registration Memory number.

Inserts the number of the currently

selected Registration Memory preset

immediately before the cursor position.

Deletes the number at the

cursor position.

Deletes all Registration

Memory numbers in the

sequence.

Setting Registration

Sequence Enable to “ON”

overrides any other Pedal

settings (for pedals assigned

to “Regist (+) Pedal” and

“Regist (-) Pedal” here).

These include the pedal set-

tings on page 131, and in

Voice Set on page 135.

When both “Regist (+)

Pedal” and “Regist (-) Pedal”

are set to “OFF,” the pedals

cannot be used to step

through the Registration

Sequence; only the [BACK]/

[NEXT] buttons can be used

in the MAIN display.

When both “Regist (+)

Pedal” and “Regist (-) Pedal”

are set to the same pedal,

“Regist (+) Pedal” takes

priority.

Registration Sequence data

is included as part of the

Registration Memory bank

ﬁle. To save your newly pro-

grammed Registration

Sequence, store the current

Registration Memory bank

ﬁle (page 39, 45). Any Reg-

istration Sequence data is

lost when changing Regis-

tration Memory banks,

unless you’ve stored it with

the Registration Memory

bank ﬁle.

Execute the settings by pressing the [EXIT] button.

END

Making Global and Other Important Settings — Function

135

CVP-205/203

Changing the Automatically Selected Voice Settings — Voice Set

When changing voices (selecting a voice ﬁle), the settings best matching the voice — the same as those set in the Sound

Creator — are always and automatically called up. From this page , you can set the on/off status for each part. For

example, each of the preset voices has its own LEFT PEDAL setting; however, even changing voices will not change the

LEFT PEDAL setting, if it is set to "OFF" in this page.

The explanations here apply to step #3 of the procedure on page 125.

Use these to select the

desired part.

These determine whether the corresponding

voice-related settings (Voice selection, Effects,

Harmony/Echo, and left pedal assignment) are

automatically called up or not when you select

a voice. These settings can be turned on or off

independently for each part.

Normally, these should all be

set to "ON."

Harmony/Echo and Left

pedal assignment cannot be

set for the Layer and Left

parts.

Setting Harmony and Echo

Determines the Harmony type.

For details, see page 136.

Determines the lowest velocity value at

which the harmony note will sound. This

allows you to selectively apply the harmony

by your playing strength, letting you create

harmony accents in the melody. The

harmony effect is applied when you play

the key strongly (above the set value).

Determines the level of the Harmony effect.

Determines the speed of the Echo, Tremolo, and Trill

effects. This parameter is only available when Echo,

Tremolo, or Trill is selected in Type above.

This lets you assign the Harmony

effect to various parts. For details,

see page 136.

When this is set to “ON,” the Harmony

effect is applied only to the note that

belongs to a chord played in the Auto

Accompaniment section of the keyboard.

This parameter is not available when Multi

Assign, Echo, Tremolo, or Trill is selected in

Type above.

Making Global and Other Important Settings — Function

CVP-205/203

136

About the Harmony Types

When a normal Harmony type (“Standard Duet” through “Strum”) is selected

When “Multi Assign” is selected

Multi Assign automatically assigns notes played simultaneously on the right-hand section of the keyboard to

separate parts (voices). For example, if you play two consecutive notes, the ﬁrst is played by the Main voice and the

second by the Layer voice.

When “Echo” is selected

An echo effect is applied to the note played on the keyboard, in time with the currently set tempo.

When “Tremolo” is selected

A tremolo effect is applied to the note played on the keyboard, in time with the currently set tempo.

When “Trill” is selected

Two notes held on the keyboard are played alternately, in time with the currently set tempo.

About the Harmony Assignments

Multi

This automatically assigns the 1st, 2nd, 3rd, and 4th added harmony notes to different parts (voices). For example, if the

Main and Layer parts are turned on and the “Standard Duet” type is selected, the note you play on the keyboard will be

played by the Main voice, and the added harmony note will be played by the Layer voice.

Main

Harmony is applied only to the Main part.

Layer

Harmony is applied only to the Layer part. When the Layer part is turned off, Harmony is not applied.

The explanations here apply to step #3 of the procedure on page 125.

Split point

Chords played to the left of the

split point control the harmony.

Harmony notes (based on the chord

and the selected type) are automatically

added to the melody played to the right

of the split point.

Showing the Clavinova Display on a TV — Video Out (CVP-205 only)

• Occasionally some ﬂashing parallel

lines may appear in the television or

video monitor. This does not necessarily

indicate that the monitor is malfunction-

ing. You may be able to remedy the situ-

ation by changing the Character Color

or Background Color parameters. For

optimum results, also try adjusting the

color settings on the monitor itself.

• Avoid looking at the television or video

monitor for prolonged periods of time

since doing so could damage your eye-

sight. Take frequent breaks and focus

your eyes on distant objects to avoid

eyestrain.

• Keep in mind that even after adjusting

all settings as recommended here, the

monitor you are using may not show the

CVP-205’s display contents as expected

(e.g., the display contents may not ﬁt on

the screen, the characters may not be

completely clear, or the colors may be

incorrect).

VIDEO IN

Television

VIDEO OUT

Set this to

correspond to the

standard used by

your particular

television/video

equipment: NTSC

or PAL.

Set this to “SMALL” if the contents of the

display do not ﬁt in your monitor screen.

Determines the background color

of the display.

Determines the colors of the characters

displayed on the video screen.

Making Global and Other Important Settings — Function

137

CVP-205/203

In this section, you can make MIDI-related settings for the instrument. These settings can be stored all together from the

USER display, for future recall.

For general information and details about MIDI, see “What is MIDI?” (page 148).

The explanations here apply to step #3 of the procedure on page 125.

Making Overall System Settings (Local Control, Clock, etc.) — System

Call up the display as described in step 2 above.

Local Control

Turns the Local Control for each part on or off. When Local Control is set to “ON,” the keyboard of the CVP-205/203

controls its own (local) internal tone generator, allowing the internal voices to be played directly from the keyboard. If

you set Local to “OFF,” the keyboard and controllers are internally disconnected from the CVP-205/203’s tone

generator section so that no sound is output when you play the keyboard or use the controllers. For example, this allows

you to use an external MIDI sequencer to play the CVP-205/203’s internal voices, and use the CVP-205/203 keyboard

to record notes to the external sequencer and/or play an external tone generator.

Setting the MIDI Parameters

Select the desired template.

Call up the Edit display, then

select and set the desired

functions/parameters.

For details about each of the

MIDI edit displays, see the

following pages.

Preset MIDI Templates (Factory Set)

All Parts Transmit all parts including Main, Layer

and Left.

Master KBD The Clavinova functions as a master

keyboard for controlling external tone

generators or other devices.

KBD & Style Transmit Upper and Lower keyboard play

instead of the individual parts (Main/

Layer/Left).

Song All Transmit channels are set to

correspond to the Song channels 1-16.

Use this to play the Clavinova song data

with an external tone generator, or to

record your entire performance to an

external sequencer.

Clock Ext. MIDI IN terminal receives MIDI clock and

Clavinova synchronizes with a external

MIDI device.

MIDI Accord 1 An ideal setup for controlling the

keyboard voice and accompaniment

style with a MIDI accordion.

MIDI Accord 2 Chord and bass buttons on a MIDI

accordion control the accompaniment

style, as well as play the chord and bass

parts.

MIDI Pedal 1 The MIDI pedal connected to MIDI IN

terminal controls the bass note of the

accompaniment.

MIDI Pedal 2 The MIDI pedal connected to MIDI IN

terminal plays the bass part.

MIDI OFF MIDI signals are neither sent nor

received.

Call up the User display

and press this button to

save the newly edited

MIDI settings.

Up to ten setups can

be saved.

Press the [EXIT] button to return to the previous display.

END

The saved settings can be named (page 42)

or deleted (page 44) in the User page.

For editing the Local Control parameters.

For editing the Message Switch

parameters.

For editing the Clock, Transmit Clock,

Receive Transpose, and Start/Stop

parameters.

Making Global and Other Important Settings — Function

CVP-205/203

138

Clock, Transmit Clock, Receive Transpose, Start/Stop

■ Clock

Determines whether the CVP-205/203 is controlled by its own internal clock or a MIDI clock signal received from

an external device. “INTERNAL” is the normal Clock setting when the CVP-205/203 is being used alone. If you are

using the CVP-205/203 with an external sequencer, MIDI computer, or other MIDI device, and you want the CVP-

205/203 to be synchronized to the external device, set this function to “EXTERNAL.” In the latter case, the external

device must be connected to the CVP-205/203 MIDI IN terminal, and must be transmitting an appropriate MIDI

clock signal.

■ Transmit Clock

Turns MIDI clock transmission on or off. When this is set to “OFF,” no MIDI clock or START/STOP data is

transmitted.

■ Receive Transpose

When this parameter is set to “OFF,” note data received by the CVP-205/203 is not transposed, and when it is set to

“ON,” the received note data is transposed according to the current CVP-205/203 keyboard transpose (page 133) setting.

■ Start/Stop

Determines whether incoming FA (start) and FC (stop) messages affect song or

style playback.

Message Switch

SYS/EX. Tx (TRANSMIT)..................... Turns MIDI transmission of MIDI system

exclusive message data ON or OFF.

SYS/EX. Rx (RECEIVE) ........................ Turns MIDI reception of MIDI exclusive data generated by external equipment

ON or OFF.

CHORD SYS/EX. Tx (TRANSMIT) ...... Turns MIDI transmission of MIDI chord exclusive data (chord detect — root and

type) ON or OFF.

CHORD SYS/EX. Rx (RECEIVE).......... Turns MIDI reception of MIDI chord exclusive data generated by external

equipment ON or OFF.

Transmitting MIDI Data — Transmit

Data Types in the MIDI TRANSMIT/RECEIVE Display

* Available in RECEIVE display only (page 139).

Note Messages which are generated when the keyboard is played. Each message includes a speciﬁc note number

which corresponds to the key which is pressed, plus a velocity value based on how hard the key is played.

Control Change (CC) Control change data includes pedal and any other controller data.

Program Change (PC) Program change data corresponds to voice or “patch” numbers.

Pitch Bend (PB) See page 132.

After Touch (AT)* With this function, the Clavinova senses how much pressure you apply to the keys while playing, and uses that

pressure to affect the sound in various ways, depending on the selected voice. This allows you to play with greater

expressiveness and add effects with your playing technique.

FA, FC

MIDI messages for starting/stop-

ping the song or style. The “FA”

message corresponds to start,

and “FC” corresponds to stop.

Determines the

channel for changing

transmit settings.

Determines the Part for the

selected channel.

Turns transmission of the

speciﬁed data type on or

off. See below for details

on the data types.

The dots corresponding

to each channel (1-16)

ﬂash brieﬂy whenever

any data is transmitted

on the channel(s).

This determines which parts will

send MIDI data and over which

MIDI channel the data will be sent.

Making Global and Other Important Settings — Function

139

CVP-205/203

Receiving MIDI Data — Receive

MIDI Receive Parts

Setting Root Note Channels — Root

The note ON/OFF messages received at the channel(s) set to “ON” are recognized as the root notes in the

accompaniment section. The root notes will be detected regardless of the accompaniment ON/OFF and split point

settings.

Setting Chord Channels — Chord Detect

The note ON/OFF messages received at the channel(s) set to “ON” are recognized as the chord notes in the

accompaniment section. The chords to be detected depend on the ﬁngering type. The root notes will be detected

regardless of the accompaniment ON/OFF and split point settings. The operation procedure is basically the same as that

of the ROOT display above.

OFF No MIDI data is received.

SONG Normally, the part receiving the MIDI data corresponds to the part/voice used in playing back the song data. Channels 1 - 16

correspond to song channels 1 - 16, respectively.

MAIN The MAIN part is controlled by the MIDI data received on the corresponding channel.

LAYER The LAYER part is controlled by the MIDI data received on the corresponding channel.

LEFT The LEFT part is controlled by the MIDI data received on the corresponding channel.

KEYBOARD MIDI note data received by the Clavinova plays the corresponding notes in the same way as if they are played on the keyboard.

ACMP RHYTHM1-2 The received notes are used as the accompaniment RHYTHM 1 and RHYTHM 2 notes.

ACMP BASS The received notes are used as the accompaniment BASS notes.

ACMP CHORD1-2 The received notes are used as the accompaniment CHORD 1 and CHORD 2 notes.

ACMP PAD The received notes are used as the accompaniment PAD notes.

ACMP PHRASE1-2 The received notes are used as the accompaniment PHRASE 1 and PHRASE 2 notes.

EXTRA PART1-5 There are ﬁve parts specially reserved for receiving and playing MIDI data. Normally, these parts are not used by the instrument

itself. When these ﬁve channels are enabled, you can use the instrument as a 32-channel multi-timbral tone generator.

Determines the channel for

changing receive settings.

Determines the Part for the

selected channel. See below for

details about the receive parts.

Turns reception of the

speciﬁed data type on or off.

See page 138 for details on

the data types.

The dots corresponding to each

channel (1 - 32) ﬂash brieﬂy

whenever any data is received

on the channel(s).

The MIDI IN/OUT terminals

and Port A of the TO HOST

terminal (Port A of the CBX

driver) correspond to chan-

nels 1 - 16. Port B of the TO

HOST terminal (Port B of the

CBX driver) corresponds to

channels 17 - 32.

This determines which parts will

receive MIDI data and over which

MIDI channel the data will be

received.

Selects the channels in groups of

eight: 1 - 8, 9 - 16, 17 - 24, and 25

- 32, respectively.

Sets the desired channel to ON or OFF. Sets all channels to OFF.

The MIDI IN/OUT terminals

and Port A of the TO HOST

terminal (Port A of the CBX

driver) correspond to chan-

nels 1 - 16. Port B of the TO

HOST terminal (Port B of the

CBX driver) corresponds to

channels 17 - 32.

When several channels are

simultaneously set to “ON,”

the root note is detected

from merged MIDI data

received over the channels.

Making Global and Other Important Settings — Function

CVP-205/203

140

The explanations here apply to step #3 of the procedure on page 125.

Making Settings for Fade In/Out, Metronome, Parameter Lock, and

Tap — CONFIG 1

Fade In Time, Fade Out Time, Fade Out Hold Time

These determine how long it takes for the accompaniment style and song to fade in or fade out.

Metronome

These let you make settings for the metronome-related parameters.

Other Settings — Utility

Determines the time it takes for the

volume to fade in, or go from minimum to

maximum (range of 0 - 20.0 seconds).

Determines the time it takes for the volume to

fade out, or go from maximum to minimum

(range of 0 - 20.0 seconds).

Determines the time the volume is held

at 0 following the fade out (range of 0 -

5.0 seconds).

Determines the level of the

metronome sound.

Determines which sound is used for the metronome.

Bell Off ........................ Conventional metronome sound, with no bell.

Bell On......................... Conventional metronome sound, with bell.

English Voice .............. Count in English (One, Two, Three, Four)

German Voice.............. Count in German (Eins, Zwei, Drei, Vier)

Japanese Voice........... Count in Japanese (Ichi, Ni, San, Shi)

French Voice ............... Count in French (Un, Deux, Trois, Quatre)

Spanish Voice ............. Count in Spanish (Uno, Dos, Tres, Cuatro)

Determines the time

signature of the metronome

sound.

When you start the song or

accompaniment style, the

values matching to them are

automatically set.

Making Global and Other Important Settings — Function

141

CVP-205/203

Parameter Lock

This function is used to “lock” the speciﬁed parameters so that they can only be changed directly via the panel controls

— in other words, instead of via Registration Memory, One Touch Setting, Music Finder, or song and sequence data.

Tap Count

This lets you change settings of the tap sound, used for the Tap Start function (page 52).

Making Settings for the Display, Speaker System, and Voice Number

Indication — CONFIG 2

Selects the desired

parameter for locking/

unlocking.

Determines whether the selected

parameter is locked (checkmarked)

or unlocked (empty).

Determines the level of the tap

sound.

Determines the particular sound

used for the Tap Start function.

Any drum or percussion sound

in the Standard Kit (page 56)

can be selected.

Determines the brightness of

the backlit display.

Determines whether or not the voice bank

and number are shown in the PRESET

page of the VOICE display (page 55). This is

useful when you want to check the proper

bank select MSB/LSB values and program

number to specify when selecting the voice

from an external MIDI device.

HEADPHONE SW (SWITCH)

Speaker sounds normally, but is cut off

when headphones are inserted to the

PHONES jack.

Speaker sound is always on.

OFF

Speaker sound is off.

Making Global and Other Important Settings — Function

CVP-205/203

142

Copying and Formatting Disks — Disk

• Copying cannot be done

between a 2DD disk and

2HD disk. When copying,

make sure both disk are

the same type.

• Depending on the amount

of data contained in the

original source disk, you

may have to swap the two

disks several times until all

of the data is properly

copied.

• Make sure to read the

section “Using the Floppy

Disk Drive (FDD) and

Floppy Disks” on page 6.

Turns the Song

Auto Open

function on or

off. When this is

set to “ON,” the

Clavinova

automatically

calls up the ﬁrst

disk song when

a disk is

inserted.

This function copies all

the data from one disk

to another, letting you

back up all your

important data before

editing. For instructions,

see “Copying from Disk

to Disk” below.

This function formats a

ﬂoppy disk (see below).

Source

disk

Copy Copy

Destination

disk

Internal memory

Copying from Disk to Disk

As shown below, ﬁrst copy the data of the original (source) disk to the CVP-205/203,

then copy the data to the backup (destination) disk.

Press the [F] button. A message

appears, prompting you to insert

the source disk.

Insert the disk containing the

original data into the drive and

press “OK.”

A “Now copying” message

appears, and the CVP-205/203

begins copying data to internal

memory. To abort the operation,

press “CANCEL.”

At the “Please insert a destination

disk and press the OK button ”

prompt, eject the source disk and

replace it with a blank, formatted

disk, then press “OK.” To abort the

operation, press “CANCEL.”

When the operation is ﬁnished

(or when prompted), eject the

destination disk.

Commercially available

music data is subject to

protection by copyright

laws. Copying commer-

cially available data is

strictly prohibited,

except for your own per-

sonal use. Some music

software is purposely

copy-protected and

cannot be copied.

Formatting a Disk

When using an unformatted disk for the ﬁrst

time, make sure to properly format it on the

CVP-205/203. This includes blank disks as

well as disks already initialized in a different

format. Formatting erases all data on the disk.

Insert the disk with shutter facing away from

you and the label side up. To start the Format

operation, press the [H] (DISK FORMAT)

button, in the DISK page above.

The Format operation initial-

izes a disk with a speciﬁc ﬁle

system, allowing the corre-

sponding device (in this

case, the CVP-205/203) to

access it properly.

Since there are several

types of formats and disks

available, you should know

which ones to use with the

CVP-205/203. 2DD disks

are formatted to a capacity

of 720 KB, and 2HD disks

are formatted to a capacity

of 1.44 MB.

Formatting a disk completely

erases all data on the disk.

Make sure that the disk

you’re formatting does not

contain important data!

CAUTION

Disk Lamp

When the power is turned on, the disk lamp

(at the bottom left of the drive) lights to

indicate the drive can be used.

Making Global and Other Important Settings — Function

143

CVP-205/203

Entering Your Name and Language Preference — Owner

Restoring the Factory-programmed Settings of the CVP-205/203 —

System Reset

This operation lets you restore the CVP-205/203 to its original factory settings. These settings include System Setup,

MIDI Setup, User Effect, Music Finder, and Files & Folders.

Press this button to enter an

Owner name (page 17; for

instructions on naming see

page 46). This name is

automatically shown when you

turn the power on.

Determines the language

used for the display

messages. Once you

change this setting, all

messages will be shown in

the selected language.

When “JAPANESE” is selected for the Language parame-

ter, and you change this to one of the western languages,

the kanji and kana characters of the ﬁle name stored in

the disk drive are changed to western characters. In the

opposite case, special Latin characters and marks are

changed into normal characters. Also, in the case of

ﬂoppy disk data, text in the ﬁles are changed to characters

that cannot be read by the instrument.

Keep in mind that similar problems may occur when trying

to access ﬁles originating or edited by a computer having

a different language operating system. In general, be

careful when switching languages — you risk not being

able to access the data properly.

These call up the corresponding Open/

Save displays. These let you store the

corresponding data as ﬁles to disk, for

future recall. Pressing each of these

buttons calls up the corresponding

Open/Save display, from which you can

select the corresponding PRESET

page. From this PRESET page, you

can save the relevant data.

Restores the System Setup parameters to the

original factory settings. You can also restore

only the System Setup settings by

simultaneously holding down the highest key

on the keyboard (C7) and turning on the power.

Restores the MIDI

templates to the original

factory settings.

Restores the User Effects

(page 123) to the original

factory settings.

Restores the Music Finder

data to the original factory

settings.

Deletes all ﬁles and folders

stored in the User page.

Executes the Factory Reset operation

for all items checkmarked above.

The functions and settings

below do not apply to the

Factory Reset operation.

However, you can restore

these to their original set-

tings by calling up the preset

System Setup ﬁles, using

the Open/Save System Files

function.

Language

Owner Name

LCD Brightness

Video Out settings (NTSC/

PAL, Size, Character Color,

Background Color) (CVP-

205 only)

All Music Finder records can

be stored together as a sin-

gle ﬁle. When calling up a

stored ﬁle, a message

appears prompting you to

replace or append the

records as desired.

Replace:

All Music Finder records cur-

rently in the instrument are

deleted and replaced with

the records of the selected

ﬁle.

Append:

The records called up are

added to the vacant record

numbers.

CVP-205/203

144

Using Your Clavinova with Other Devices

1 Using the Headphones

(PHONES jacks).

To use headphones, connect them to one of the PHONES

jacks (standard 1/4" phone jacks) located on the under-

side of the keyboard. You can also determine whether or

not the internal stereo speaker system is shut off when a

pair of headphones is plugged into the PHONES jack

(page 141). Two people can enjoy listening to the Clavi-

nova together by connecting two pairs of headphones to

the two jacks.

2 Connecting the Microphone

or Guitar (MIC./LINE IN jack)

(CVP-205 only).

By connecting a microphone to the CVP-205, you can

enjoy singing along with your own performance or song

playback. (A dynamic microphone is recommended.) The

Clavinova outputs your vocals or guitar sounds through

the built-in speakers.

Connect your microphone to the MIC./LINE IN jack

(standard 1/4" phone jack).

Set the [MIC. LINE] switch (located next to the

[MIC./LINE IN] jack) to the MIC. position.

Use the [INPUT VOLUME]

knob (located next to the

MIC./LINE IN jack) to set the

microphone volume.

CVP-205

CVP-203

Before connecting the Clavinova to other electronic components,

turn off the power to all the components. Before turning the power

on or off to all components, set all volume levels to minimum (0).

Otherwise, electrical shock or damage to the components may

occur.

CAUTION

MIN MAX

INPUT

MIC.

MIC. LINE PHONES

VOLUME

LINE IN

PHONES

1 12

CVP-205 CVP-203

Use an unidirectional microphone for best results.

MIC. LINE MIC. LINE

When connecting a microphone When connecting a guitar

You should set the [MIC. LINE] switch to the LINE position when

connecting an audio source with line-level output to the MIC./LINE

IN jack.

8654 37

IN OUT THRU

PC-1PC-2

MIDI Mac

(

LEVEL FIXED

)

TO HOST AUX PEDAL VIDEO OUT AUX IN AUX OUTHOST SELECTMIDI

L L+R R L L+R R

P.145 P.145P.145P.146P.146 P.146

68 7

AUX OUT AUX IN

LL L+RRR LL+RR

(

LEVEL FIXED

)

PC-1 PC-2

MIDIMac

INOUTTHRU

MIDI

TO HOSTAUX PEDAL HOST SELECT

P.145 P.145

P.146P.146 P.146

Using Your Clavinova with Other Devices

145

CVP-205/203

345 Connecting Audio &

Video Devices

You can connect the Clavinova to a wide range of audio

equipment by using the AUX IN and AUX OUT jacks,

which are located at the bottom left of the instrument.

Connect as shown in the illustrations below using

standard audio cables.

3 Playing the sounds of the Clavinova

through an external audio system, and

recording the sounds to an external

recorder (AUX OUT jacks)

4 Outputting the sound of an external

device through the built-in speakers of

the Clavinova (AUX IN jacks)

5 Showing the display of the Clavinova on

a connected TV monitor (VIDEO OUT)

(CVP-205 only)

You can connect the Clavinova to a television or video

monitor to display the lyrics in your song data or LCD

on a larger screen.

The size and color of the displayed characters can also

be set, as well as the color of the display background

(page 136).

Use audio cables and adaptor plugs with no resistance.

When the Clavinova AUX OUT jacks are connected to an external

audio system, ﬁrst turn on the power to the Clavinova, then to the

external audio system. Reverse this order when you turn the power

off.

CAUTION

Never connect the Clavinova AUX OUT jacks to its AUX IN jacks,

either directly or via external audio equipment. Such connections

could result in a feedback loop that will make normal performance

impossible, and may even damage the Clavinova.

CAUTION

(

LEVEL FIXED

)

AUX OUT

L L+R R

Audio cable

To powered speaker

RCA pin

plug

RCA pin plug

AUX IN

Cassette tape recorder

stereo system

Phone plug

(standard)

When these are connected

(with RCA pin plug; LEVEL

FIXED), the sound is output to

the external device at a ﬁxed

level, regardless of the

[MASTER VOLUME] control

setting.

When these are connected

(with standard phone

plugs), you can use the

[MASTER VOLUME]

control to adjust the volume

of the sound output to the

external device.

Clavinova

• If you connect the Clavinova to a monaural device, use only the

AUX OUT L/L+R jack.

When the Clavinova’s AUX IN jacks are connected to an external

device, ﬁrst turn on the power of the external device, then that of

the Clavinova.

CAUTION

AUX IN

L L+R R

Audio cable

LINE OUT

Tone generator

Phone plug

(standard)

Clavinova

• The Clavinova’s [MASTER VOLUME] setting affects the input

signal from the AUX IN jacks.

• If you connect the Clavinova to a monaural device, use only the

AUX IN L/L+R jack.

• For information on setting the video standard (NTSC or PAL),

refer to page 136. The default setting is “PAL.”

• Use an audio-video cable with good high-frequency characteris-

tics and RCA-type pin jacks to connect the Clavinova to a televi-

sion or video monitor.

AUX PEDAL VIDEO OUT AUX IN

L L+R R

RCA pin

plug

RCA pin

plug

VIDEO IN

Television

CVP-205

Using Your Clavinova with Other Devices

CVP-205/203

146

6 Using the Pedal (footswitch)

or Foot Controller (AUX

PEDAL jack)

By connecting an optional Foot Controller (such as the

FC7) to the AUX PEDAL jack, you can control any one of

a variety of important functions with your foot — such as

dynamically adjusting the volume as you play (page 131).

By connecting a Foot Switch (the FC4 or FC5) to this jack,

you can replicate the function of some panel buttons,

doing things like starting and stopping accompaniment.

7 Connecting external MIDI

devices (MIDI terminals)

Using a standard MIDI cable, connect the external MIDI

device to the MIDI terminal(s) of the Clavinova. Make

sure to set the HOST SELECT switch (page 18) to MIDI

when you use these connectors. For more information

about connections, see “What You Can Do With MIDI” on

page 150.

MIDI IN........... Receives MIDI messages from an

external MIDI device

MIDI OUT ....... Sends out MIDI messages generated by

the Clavinova

MIDI THRU ..... Simply relays the MIDI messages

received at MIDI IN

For a general overview of MIDI and how you can

effectively use it, refer to the following sections:

• What’s MIDI? (page 148)

• What You Can Do With MIDI (page 150)

• MIDI functions (page 137)

8 Connecting to a Computer

(MIDI terminals/TO HOST

terminal)

Connect your CVP-205/203 to computer and take

advantage of the wide range of powerful and versatile

software for creating and editing music. The CVP-205/203

can be connected in three ways.

■ Using the TO HOST terminal

■ Using the MIDI terminals

■ Connecting to a USB terminal by using an optional

USB interface (UX series)

Make sure to connect or disconnect the pedal only when the power

is turned off.

CAUTION

• Never use MIDI cables longer than 15 meters.

Note for Windows users (regarding MIDI

driver)

To transfer data via the computer’s serial port and the

Clavinova’s TO HOST terminal, you need to install a

speciﬁed MIDI driver (Yamaha CBX driver for

Windows). You can download this driver from the XG

Library on the Yamaha Web site:

http://www.yamaha-xg.com

• Yo u ’ll need an appropriate music/MIDI software program (such

as a sequencer), compatible with your computer platform.

• When connecting the Clavinova to a personal computer, ﬁrst turn

off the power to both the Clavinova and the computer before con-

necting any cables and setting the HOST SELECT switch. After

making the proper connections and settings, turn on the power of

the computer ﬁrst, then that of the Clavinova.

• If you do not use the TO HOST terminal of the Clavinova, make

sure you disconnect the cable from the terminal. If the cable is

left connected, the Clavinova may not function properly.

• When the HOST SELECT switch is set to “PC-1,” “PC-2,” or

“Mac,” you can use the TO HOST terminal, but the MIDI connec-

tors are disabled since no data transfer occurs via the MIDI con-

nectors. On the other hand, when the HOST SELECT switch is

set to “MIDI,” you can use the MIDI connectors, but not the TO

HOST terminal since no data is transferred via the TO HOST ter-

minal.

Using Your Clavinova with Other Devices

147

CVP-205/203

Using the TO HOST terminal

Connect the serial port of the personal computer (RS-

232C terminal or RS-422 terminal) to the TO HOST

terminal of the CVP-205/203. For the connection cable,

use the appropriate cable below (sold separately) that

matches the personal computer type.

■ IBM-PC/AT (Windows)

Connect the RS-232C terminal on the computer to the

TO HOST terminal on the CVP-205/203 using a serial

cable (D-SUB 9P → MINI DIN 8P cross cable). Set the

CVP-205/203 HOST SELECT switch to the “PC-2.”

(Data transfer rate is 38,400 bps.)

■ Macintosh

Connect RS-422 terminal (modem or printer) on the

computer to the TO HOST terminal on the CVP-205/

203 using a serial cable (system peripheral cable, 8

bit). Set the CVP-205/203 HOST SELECT switch to the

“MAC” (Data transfer rate is 31,250 bps).

Set the MIDI interface clock in the sequencer you are

using to 1 MHz. For details, refer to the owner’s

manual for the particular software you are using.

Using the MIDI terminals

When using a MIDI interface device installed in the

personal computer, connect the MIDI terminals of the

personal computer and the CVP-205/203 with standard

MIDI cables.

• When the computer has a MIDI interface installed,

connect the MIDI OUT terminal of the personal

computer to the MIDI IN terminal. Set the HOST

SELECT switch to “MIDI.”

• When using a MIDI interface with a Macintosh series

computer, connect the RS-422 terminal of the

computer (modem or printer terminal) to the MIDI

interface, then connect the MIDI OUT terminal on the

MIDI interface to the MIDI IN terminal of the CVP-

205/203, as shown in the diagram below.

Set the HOST SELECT switch to “MIDI.”

• When the HOST SELECT switch is set to “MIDI,” the

TO HOST terminal is disabled.

• When using a Macintosh series computer, set the

MIDI interface clock setting in the application

software to match the setting of the MIDI interface

you are using. For details, refer to the owner’s

manual for the particular software you are using.

If your system does not work properly with the connections and

settings listed above, your software may require different settings.

Check your software operation manual and set the HOST SELECT

switch to the proper data transfer rate. (Data transfer rate of “PC-1”

is 31,250 bps.)

NEC

PC-9821

NEC MultiSync

MINI DIN

8-pin

D-sub

9-pin

MINI DIN

8-pin

D-sub

25-pin

D-sub

9-pin

PC-1PC-2

MIDI Mac

PC-1 PC-2

MIDIMac

CVP-205

CVP-203

Clavinova

* When using a D-SUB 25P

→ MINI DIN 8P cross

cable, connect using a D-

SUB9P plug adaptor on

the computer side of the

cable.

MINI DIN

8-pin

MINI DIN

8-pin

PC-1PC-2

MIDI Mac

PC-1 PC-2

MIDIMac

CVP-205 CVP-203

Clavinova

NEC

PC-9821

NEC MultiSync

MIDI IN MIDI OUT

MIDI OUT MIDI IN

PC-1PC-2

MIDI Mac

PC-1 PC-2

MIDIMac

CVP-205 CVP-203

Clavinova

MIDI IN

RS422

MIDI OUT

MINI DIN

8-pin

PC-1PC-2

MIDI Mac

PC-1 PC-2

MIDIMac

CVP-205 CVP-203

Clavinova

Using Your Clavinova with Other Devices

CVP-205/203

148

Using the USB terminal on your computer

with a USB/MIDI interface (UX256/UX96,

etc.)

Connect the UX256/UX96 and the computer with a USB

cable. Install the included UX256/UX96 driver to the

computer, and connect the UX256/UX96 to the CVP-205/

203 with a MIDI cable. Set the HOST SELECT switch on

the CVP-205/203 to “MIDI.” For details, refer to the

owner’s manual of the UX256/UX96.

For details about the necessary MIDI settings for computer

and sequence software you are using, refer to the relevant

owner’s manuals.

What’s MIDI?

Let’s consider an acoustic piano and a classical guitar as

representative acoustic instruments. With the piano, you

strike a key, and a hammer inside hits some strings and

plays a note. With the guitar, you directly pluck a string

and the note sounds.

But how does a digital instrument go about playing a

note?

As shown in the illustration above, in an electronic

instrument, the sampled note (previously recorded note)

stored in the tone generator section (electronic circuit) is

played based on information received from the keyboard,

and output through the speakers.

Now let’s examine what happens when we play back a

recording. When you playback a music CD (for example,

a solo piano recording), you’re hearing the actual sound

(vibrations in air) of the acoustic instrument. This is called

audio data, to distinguish it from MIDI data.

In the above example, the actual acoustic sounds of the

pianist’s performance are captured in the recording as

audio data, and this is recorded to CD. When you play

back that CD on your audio system, you can hear the

actual piano performance. The piano itself is not

necessary, since the recording contains the actual sounds

of the piano, and your speakers reproduce them.

Personal computer

MIDI IN

USB

cable

MIDI OUT

UX256

NEC

PC-9821

NEC MultiSync

PC-1PC-2

MIDI Mac

PC-1 PC-2

MIDIMac

CVP-205 CVP-203

Clavinova

IN OUT

MIDI

Internal ampInternal amp

Tone generator

(Electric circuit)

Playing

the keyboard

Pluck a string and the body

resonates the sound.

Based on playing information

from the keyboard, a

sampled note stored in the

tone generator is played

through the speakers.

Acoustic guitar note

production

Digital instrument note

production

Recording and playing back the performance of an acoustic

instrument (audio data)

Recording Playback

Tone generator

Sequencer

Recording and playing back the performance of a digital

instrument (MIDI data)

Controller (keyboard, etc.)

Recording Playback

In the case of digital instruments, the audio signals are sent

through output jacks (such as AUX OUT) on the instrument.

Using Your Clavinova with Other Devices

149

CVP-205/203

The “controller” and “tone generator” in the illustration

above are equivalent to the piano in our acoustic

example. Here, the player’s performance on the keyboard

is captured as MIDI song data (see illustration below). In

order to record the audio performance on an acoustic

piano, special recording equipment is needed. However,

since the Clavinova features a built-in sequencer that lets

you record performance data, this recording equipment is

unnecessary. Instead, your digital instrument — the

Clavinova — allows you to both record and play back the

data.

However, we also need a sound source to produce the

audio, which eventually comes from your speakers. The

tone generator of the Clavinova ﬁlls this function. The

recorded performance is reproduced by the sequencer,

playing back the song data, using a tone generator

capable of accurately producing various instrument

sounds — including that of a piano. Looked at in another

way, the relation of the sequencer and the tone generator

is similar to that of the pianist and the piano — one plays

the other. Since digital instruments handle playback data

and the actual sounds independently, we can hear our

piano performance played by another instrument, such as

guitar or violin.

Finally, we’ll take a look at the actual data that gets

recorded and that serves as the basis for playing the

sounds. For example, let’s say you play a “C” quarter note

using the grand piano sound on the CVP-205/203

keyboard. Unlike an acoustic instrument that puts out a

resonated note, the electronic instrument puts out

information from the keyboard such as “with what voice,”

“with which key,” “about how strong,” “when was it

pressed” and “when was it released.” Then each piece of

information is changed into a number value and sent to

the tone generator. Using these numbers as a basis, the

tone generator plays the stored sampled note.

■ Example Keyboard Data

Panel operations on the CVP-205/203, such as playing the

keyboard and selecting voices, are processed and stored

as MIDI data. The auto accompaniment styles and songs

also consist of MIDI data.

MIDI is an acronym that stands for Musical Instrument

Digital Interface, which allows electronic musical

instruments to communicate with each other, by sending

and receiving compatible Note, Control Change, Program

Change and various other types of MIDI data, or

messages.

The CVP-205/203 can control a MIDI device by

transmitting note related data and various types of

controller data.The CVP-205/203 can be controlled by

incoming MIDI messages which automatically determine

the tone generator mode, select MIDI channels, voices

and effects, change parameter values and of course play

the voices speciﬁed for the various parts.

MIDI messages can be divided into two groups: Channel

messages and System messages.

■ Channel Messages

The CVP-205/203 is an electronic instrument that can

handle 16 channels (or 32 channels, when using the TO

HOST terminal). This is usually expressed as “it can play

16 instruments at the same time.” Channel messages

transmit information such as Note ON/OFF, Program

Change, for each of the 16 channels.

Tone generator

Sequencer

Keyboard performance

(MIDI data)

Even though it is a single musical instrument, the Clavinova can be

thought of as containing several electronic components: a control-

ler, a tone generator, and a sequencer.

Voice number (with what voice) 01 (grand piano)

Note number (with which key) 60 (C3)

Note on (when was it pressed)

and

note off (when was it released)

Timing expressed numerically

(quarter note)

Velocity (about how strong) 120 (strong)

Message Name CVP-205/203 Operation/Panel Setting

Note ON/OFF Messages which are generated when the

keyboard is played. Each message includes

a speciﬁc note number which corresponds

to the key which is pressed, plus a velocity

value based on how hard the key is played.

Program Change Voice selecting (control change bank select

MSB/LSB setting)

Control Change Volume, panpot (Mixing Console), etc.

MIDI data has the following advantages over audio data:

• The amount of data is much less, letting you easily store MIDI

songs to ﬂoppy disk.

• The data can be effectively and easily edited, even to the point of

changing voices and transforming the data.

The performance data of all songs and styles is handled as MIDI

data.

Using Your Clavinova with Other Devices

CVP-205/203

150

MIDI channels

MIDI performance data is assigned to one of sixteen

MIDI channels. Using these channels, 1 - 16, the

performance data for sixteen different instrument parts

can be simultaneously sent over one MIDI cable.

Think of the MIDI channels as TV channels. Each TV

station transmits its broadcasts over a speciﬁc

channel.Your home TV set receives many different

programs simultaneously from several TV stations and

you select the appropriate channel to watch the desired

program.

MIDI operates on the same basic principle. The

transmitting instrument sends MIDI data on a speciﬁc

MIDI channel (MIDI Transmit Channel) via a single

MIDI cable to the receiving instrument. If the receiving

instrument’s MIDI channel (MIDI Receive Channel)

matches the Transmit Channel, the receiving instrument

will sound according to the data sent by the

transmitting instrument.

For example, several tracks (channels) can be

transmitted simultaneously, including the style data (as

shown below).

Example: Recording the auto accompaniment of the Clavinova to

an external sequencer

As you can see, it is essential to determine which data

is to be sent over which MIDI channel when

transmitting MIDI data (page 138). The Clavinova also

allows you to determine how the received data is

played back. (page 139).

■ System Messages

This is data that is used in common by the entire MIDI

system. System messages include messages like Exclusive

Messages that transmit data unique to each instrument

manufacturer and Realtime Messages that control the

MIDI device.

The messages transmitted/received by the CVP-205/203

are shown in the MIDI Data Format and MIDI

Implementation Chart in the separate Data List.

What You Can Do With MIDI

The following MIDI settings can be made on the

Clavinova:

• MIDI templates (preset MIDI setups for various

applications) (page 137)

• Transmit (page 138)

• Receive (page 139)

• Local Control (page 137)

• Clock (page 138)

■ Record performance data (1-16 channels) using the

CVP-205/203 Auto Accompaniment features on a

external sequencer (such as a personal computer).

After recording, edit the data with the sequencer, then

play it again on the CVP-205/203 (playback).

When you want to use the Clavinova as an XG-

compatible multi-timbral tone generator, set the receive

part for MIDI channels 1 to 16 to “SONG” in MIDI

Receive (page 139).

■ Play and control the Clavinova from a separate

keyboard

Weather Report

News

MIDI transmit channel 2 MIDI receive channel 2

MIDI

cable

The Clavinova’s keyboard and internal tone generator are also

connected by MIDI (page 137).

MIDI cable or

serial cable

Clavinova track (channnel)

MAIN

LAYER

LEFT

STYLE instrument

External sequencer

Track 1

Track 2

Track 3

Track 4

Track 5

Track 6

Track 7

Track 8

Track 9

Track 10

Track 11

Channel 1

Channel 2

Channel 3

Channel 4

Channel 5

Channel 6

Channel 7

Channel 8

Channel 9

Channel 10

Channel 11

Message Name CVP-205/203 Operation/Panel Setting

System Exclusive

Message

Effect type settings (Mixing Console),

etc.

Realtime Messages Clock setting, Start/stop operation

Personal cumputer,

QY series etc.

MIDI receive

MIDI transmit

NEC

PC-9821

NEC MultiSync

MIDI IN MIDI OUT

MIDI OUT MIDI IN

Clavinova

MIDI IN MIDI OUT

Clavinova

MIDI receive

Using Your Clavinova with Other Devices

151

CVP-205/203

Data Compatibility

This section covers basic information on data

compatibility: whether or not other MIDI devices can

playback the data recorded by CVP-205/203, and

whether or not the CVP-205/203 can playback

commercially available song data or song data created for

other instruments or on a computer. Depending on the

MIDI device or data characteristics, you may be able to

play back the data without any problem, or you may have

to perform some special operations before the data can be

played back. If you run into problems playing back data,

please refer to the information below.

Disk format

Floppy disks are the main storage medium for data used

with various devices, including computers. Different

devices have different systems of storing data, therefore it

is necessary to ﬁrst conﬁgure the ﬂoppy disk to the system

of the device being used.This operation is called

“formatting.”

• There are two types of ﬂoppy disks: MF2DD (double

sided, double density) and MF2HD (double sided,

high density), and each type has different formatting

systems.

• CVP-205/203 can record and playback with both

types of ﬂoppy disks.

• When formatted by the CVP-205/203, a 2DD disk

stores up to 720 KB (kilobytes) and a 2HD disk stores

up to1.44 MB (megabytes). (The ﬁgures “720 KB” and

“1.44MB” indicate the data memory capacity. They are

also used to indicate the format type of disk.)

• Playback is only possible when the MIDI device to be

used is compatible with the format of the disk.

Sequence Format

The system which records song data is called “sequence

format.”

Playback is only possible when the sequence format of

the disk matches that of the MIDI device. The CVP-205/

203 is compatible with the following formats.

■ SMF (Standard MIDI File)

This is the most common sequence format.

Standard MIDI Files are generally available as one of two

types: Format 0 or Format 1. Many MIDI devices are

compatible with Format 0, and most commercially

available software is recorded as Format 0.

• The CVP-205/203 is compatible with both Format 0

and Format 1.

• Song data recorded on the CVP-205/203 is

automatically recorded as SMF Format 0.

• Song data loaded to the CVP-205/203 is automatically

saved as SMF Format 0 regardless of the original

format.

■ ESEQ

This sequence format is compatible with many of

Yamaha’s MIDI devices, including the Clavinova series

instruments.This is a common format used with various

Yamaha software.

■ XF

The Yamaha XF format enhances the SMF (Standard MIDI

File) format with greater functionality and open-ended

expandability for the future.

• The CVP-205/203 is capable of displaying lyrics when

an XF ﬁle containing lyric data is played.

■ Style File

The Style File Format – SFF – is Yamaha’s original style ﬁle

format which uses a unique conversion system to provide

high-quality automatic accompaniment based on a wide

range of chord types.

Using Your Clavinova with Other Devices

CVP-205/203

152

Voice Allocation Format

With MIDI, voices are assigned to speciﬁc numbers,

called “program numbers.” The numbering standard

(order of voice allocation) is referred to as the “voice

allocation format.”

Voices may not play back as expected unless the voice

allocation format of the song data matches that of the

compatible MIDI device used for playback.

The CVP-205/203 is compatible with the following

formats.

■ GM System Level 1

This is one of the most common voice allocation formats.

• Many MIDI devices are compatible with GM System

Level1, as is most commercially available software.

■ XG

XG is a major enhancement of the GM System Level 1

format, and was developed by Yamaha speciﬁcally to

provide more voices and variations, as well as greater

expressive control over voices and effects, and to ensure

compatibility of data well into the future.

• Song data recorded on the CVP-205/203 using voices

in the [XG] category is XG-compatible.

■ DOC

This voice allocation format is compatible with many of

Yamaha’s MIDI devices, including the Clavinova series

instruments.This is also a common format used with

various Yamaha software.

Even if the devices and data used satisfy all the conditions above,

the data may still not be completely compatible, depending on the

speciﬁcations of the devices and particular data recording

methods.

153

CVP-205/203

CVP-205/205M: Keyboard Stand Assembly

CAUTION

■ Be careful not to confuse parts, and be sure to install

all parts in the correct direction. Please assemble in

accordance with the sequence given below.

■

Assembly should be carried out by at least two persons.

■ Be sure to use the correct screw size, as indicated

below. Use of incorrect screws can cause damage.

■ Be sure to tighten up all screws upon completing

assembly of each unit.

■ To disassemble, reverse

the assembly sequence

given below.

Open the package, take out the pedal box, take out

the styrofoam pads, and place the main unit on top

of the pads.

Position the pads so that they will protect the headphone

jack and the connector panel located underneath the front

left corner, and the ﬂoppy disk drive located underneath

the front right corner.

Remove the parts shown below from the box.

Attach the side panels to the pedal box.

Attach the front panel.

1 Align and attach the front panel to the front side of the pedal box

and both side panels.

2 Secure the panel using the 4x14mm thin screws.

* Insert six screws into the smaller holes on the brackets.

Mount the main unit.

Be sure to place your hands at least 10 cm from either

end of the main unit when positioning it.

Fix the main unit.

1 Center the main unit to produce equal clearance on the left and

right sides.

Connector panel

Floppy disk drive

Phones jacks Styrofoam pads

Main unit

Front panel

Rear panel

Pedal box

Side panel

(left)

Assembly Parts

AC power cord

Side panel

(right)

Pedal cord

6 x 25 mm long screws x4

4 x 20 mm tapping screws x5

6 x 16 mm short screws x4

Cord holders x24 x 14 mm thin screws x8

Side panel

(left)

Side panel

(right)

Side panel

(left)

Side panel

(right)

2 Remove the vinyl tie from the folded

pedal cord. Do not

remove the vinyl tie

located next to the

hole.

Use the four 6x25 mm

long screws to attach the

pedal box. First attach one

side panel, then attach the

other side panel

CAUTION

• Fingers can become pinched between the main unit and

the rear or side panels, be extra careful so as not to drop

the main unit.

• Do not hold the keyboard in any position other than the

position shown in the illustration.

At least

10 cm

At least

10 cm

2 Use 6x16 mm short

screws to secure the

main unit from the rear.

* Use the front hole on

the front brackets to

attach the screws.

Have a Phillips-head (+)

screwdriver ready.

CVP-205/205M: Keyboard Stand Assembly

CVP-205/203

154

Connect the speaker cord.

1 Before connecting the speaker cord, remove the vinyl tie

attaching the speaker cord to the front panel.

2 Insert the speaker cord plug into the connector, with the plug’s

tab facing the rear.

Connect the pedal cord.

Attach the rear panel.

Set the voltage selector and connect the power

cord.

Voltage Selector

Before connecting the AC power cord, check the setting

of the voltage selector which is provided in some areas.

To set the selector for 110V, 127V, 220V or 240V main

voltages, use a “minus” screwdriver to rotate the

selector dial so that the correct voltage for your region

appears next to the pointer on the panel. The voltage

selector is set at 240V when the unit is initially shipped.

After the proper voltage has been selected, connect the

AC power cord to the AC INLET and an AC wall outlet.

A plug adaptor may be also provided in some areas to

match the pin conﬁguration of the AC wall outlets in

your area.

WARNING

• An improper voltage setting can cause serious damage to the

Clavinova or result in improper operation.

■ After completing the assembly, please

check the following.

1 Insert the pedal

cord plug into the

pedal connector.

2 Attach the

cord holders

to the side

panel as

shown, then

clip the cord

into the

holders.

1 With the rear

panel on the

feet’s protruding

edge, align the

panel with the

groove and

secure the top

of the panel.

2 Secure the left and right corners using the

4x14mm thin screws.

3 Secure the top center and

bottom of the panel using the

4x20mm tapping screws.

240

127

110

220

• Are there any parts left over?

→ Review the assembly procedure and correct

any errors.

• Is the Clavinova clear of doors and other

movable ﬁxtures?

→ Move the Clavinova to an appropriate

location.

• Does the Clavinova make a rattling noise when

you shake it?

→ Tighten all screws.

• Are the pedal and power cords inserted securely

into the sockets?

→ Check the connection.

• If the main unit creaks or is otherwise unsteady

when you play on the keyboard, refer to the

assembly diagrams and retighten all screws.

When moving the instrument after assembly, always

hold instrument by the lower surface in the front of

the main unit and by the handles in the rear panel.

CAUTION

Do not hold the key cover or top portion. Improper han-

dling can result in damage to the instrument or personal

injury.

Top portion

Key cover

155

CVP-205/203

CVP-203: Keyboard Stand Assembly

CAUTION

■ Be careful not to confuse parts, and be sure to

install all parts in the correct direction. Please

assemble in accordance with the sequence given

below.

■ Assembly should be carried out by at least two

persons.

■ Be sure to use the correct screw size, as indicated

below. Use of incorrect screws can cause damage.

■ Be sure to tighten up all screws upon completing

assembly of each unit.

■ To disassemble, reverse the assembly sequence

given below.

Open the package, take out the pedal box, take

out the styrofoam pads, and place the main unit

on top of the pads.

Position the pads so that they will protect the headphone

jack and the connector panel located underneath the

front left corner, and the ﬂoppy disk drive located

underneath the front right corner.

Remove the parts shown below from the box.

Attach the side panels to the pedal box.

Attach the rear panel.

1 Place the bottom edges of the rear panel on the feet’s protruding

edges, with the panel slightly angled as shown in the illustration.

The wooden pattern side of the panel should be facing outside.

Then, align the top part of the panel with the side panels.

2 Secure the top of the rear panel to the side panel brackets using

two 4x12 mm thin screws.

3 Secure the bottom of the rear panel to the pedal box using four

4x20 mm tapping screws.

Mount the main unit.

Be sure to place your hands at least 10 cm from either

end of the main unit when positioning it.

Have a Phillips-head (+) screwdriver ready.

Floppy disk drive

Styrofoam

pads

Main unit

Bundled pedal cord inside

Rear panel

Pedal box

Side panel

(left)

Side panel

(right)

Assembly Parts AC power cord

6 x 25 mm long screws x4

4 x 20 mm tapping screws x46 x 16 mm short screws x4

Cord holders x2

4 x 12 mm thin screws x2

Side panel

(left)

Side panel

(right)

Side panel

(left)

Side panel

(right)

1 Untie and straighten out the bundled

cord attached to the bottom of the

pedal box. Don’t discard the vinyl tie,

you’ll need it later in step 6.

2 Use the four 6x25 mm long screws to attach the pedal box.

First attach one side panel, then attach the other side panel.

CAUTION

• Fingers can become pinched between the main unit and

the rear or side panels, be extra careful so as not to drop

the main unit.

• Do not hold the keyboard in any position other than the

position shown in the illustration.

At least

10 cm

CVP-203: Keyboard Stand Assembly

CVP-205/203

156

Fix the main unit.

1 Center the main unit to

produce equal clearance on

the left and right sides.

2 Use 6x16 mm short screws to

secure the main unit from the

front.

Connect the pedal cord.

Set the voltage selector and connect the power

cord.

Voltage Selector

Before connecting the AC power cord, check the setting

of the voltage selector which is provided in some areas.

To set the selector for 110V, 127V, 220V or 240V main

voltages, use a “minus” screwdriver to rotate the

selector dial so that the correct voltage for your region

appears next to the pointer on the panel. The voltage

selector is set at 240V when the unit is initially shipped.

After the proper voltage has been selected, connect the

AC power cord to the AC INLET and an AC wall outlet.

A plug adaptor may be also provided in some areas to

match the pin conﬁguration of the AC wall outlets in

your area.

WARNING

• An improper voltage setting can cause serious damage to the

Clavinova or result in improper operation.

Set the adjuster.

Rotate the adjuster until it comes in ﬁrm contact

with the ﬂoor surface.

■ After completing the assembly, please

check the following.

1 Insert the pedal

cord plug to the

pedal connector

from the front.

2 Attach the cord holders

to the rear panel as

shown, then clip the

cord into the holders.

3 Use a vinyl tie

to take up any

slack in the

pedal cord.

240

127

110

220

• Are there any parts left over?

→ Review the assembly procedure and correct

any errors.

• Is the Clavinova clear of doors and other

movable ﬁxtures?

→ Move the Clavinova to an appropriate

location.

• Does the Clavinova make a rattling noise when

you shake it?

→ Tighten all screws.

• Does the pedal box rattle or give way when you

step on the pedals?

→ Turn the adjuster so that it is set ﬁrmly against

the ﬂoor.

• Are the pedal and power cords inserted securely

into the sockets?

→ Check the connection.

• If the main unit creaks or is otherwise unsteady

when you play on the keyboard, refer to the

assembly diagrams and retighten all screws.

When moving the instrument after assembly, always

hold the bottom of the main unit.

CAUTION

Do not hold the key cover or top portion. Improper han-

dling can result in damage to the instrument or personal

injury.

Top portion

Key cover

157

CVP-205/203

Troubleshooting

Problem Possible Cause and Solution

• The Clavinova does not turn on; there is no

power.

Make sure that the Clavinova has been plugged in properly. Securely insert the

female plug into the AC socket on the Clavinova, and the male plug into a proper

AC outlet (page 17).

• A click or pop is heard when the power is

turned on or off.

This is normal when electrical current is applied to the instrument.

• Noise is heard from the Clavinova’s speakers. Using a mobile phone in close proximity to the Clavinova may produce

interference. To prevent this, turn off the mobile phone, or use it further away from

the Clavinova.

• The display is too bright or too dark to read. The brightness of the display may be affected by the surrounding temperature;

try adjusting the contrast (page 17).

• The keyboard volume is low compared to that

of the Auto Accompaniment or song playback.

The overall keyboard volume or the independent volume level of the keyboard

part may be set too low. Raise the MAIN/LAYER/LEFT volume voices or lower

the STYLE/SONG volume in the BALANCE display (page 62).

• The volume of the Auto Accompaniment or

song playback is low compared to that of the

keyboard.

The volume level of one or more accompaniment parts or song channels is set

too low. Raise the part or channel level(s) in the appropriate MIXER display

(page 120).

• The overall volume is low, or no sound is

heard.

• The Master Volume is set too low; set it to an appropriate level with the

[MASTER VOLUME] dial.

• The volume of the individual parts may be set too low. Raise the volume of

MAIN, LAYER, LEFT, STYLE, and SONG in the BALANCE display (page 62).

• Make sure the desired channel is set to ON (page 62, 77).

• Headphones are connected, disabling the speaker output. (This happens

when the speaker setting is set to “HEADPHONE SW”; page 141.) Unplug the

headphones.

• Make sure the speaker setting is set to ON (page 141).

• Make sure the Local Control function is set to ON (page 137).

• The damper, sostenuto and soft functions do

not work for the relevant pedals.

Each pedal has been assigned to a different function. Make sure that each pedal

is properly assigned to SUSTAIN, SOSTENUTO, and SOFT (page 131).

• The damper pedal has no effect, or the sound

continuously sustains even when the damper

pedal is not pressed.

The pedal cable/plug may not be properly connected. Make sure to securely

insert the pedal plug into the proper jack (page 153 - 156).

• Not all simultaneously-played notes sound. You may be exceeding the maximum polyphony of the Clavinova. When this

happens, the earliest played notes will stop sounding, letting the latest played

notes sound. See page 159 for information on the maximum polyphony.

• Accompaniment style or Song playback does

not start.

• MIDI Clock may be set to “EXTERNAL.” Make sure this is set to “INTERNAL”

(page 138).

• Make sure to press the appropriate [START/STOP] button. To play an

accompaniment style, press the STYLE [START/STOP] button (page 62); to

playback a song, press the SONG [START/STOP] button (page 75).

•“New Song” (a blank song) has been selected. Make sure to select an

appropriate song in the SONG display (page 75).

• The song has been stopped at the end of the song data. Return to the

beginning of the song by pressing the [TOP] button (page 77).

• Only the rhythm channel plays. Make sure the Auto Accompaniment function is turned on; press the [ACMP]

button.

• The accompaniment style does not start,

even when Synchro Start is in standby

condition and a key is pressed.

You may be trying to start accompaniment by playing a key in the right hand

range of the keyboard. Make sure to play a key in the left-hand (accompaniment)

range of the keyboard.

• The desired chord is not recognized or output

by the auto accompaniment.

• You may not be playing the correct keys to indicate the chord. Refer to “Chord

Types Recognized in the Fingered Mode” (page 64).

• You may be playing the keys according to a different ﬁngering mode, and not

the one currently selected. Check the accompaniment mode, and play the

keys according to the selected mode (page 63).

Troubleshooting

CVP-205/203

158

• Auto accompaniment chords are recognized

regardless of the split point or where chords

are played on the keyboard.

This is normal if the ﬁngering mode is set to “Full Keyboard” or “AI Full Keyboard.”

If either of these is selected, chords are recognized over the entire range of the

keyboard, irrespective of the split point setting. If desired, select a different

ﬁngering mode (page 63).

• Certain notes sound at the wrong pitch. The Scale parameter has probably been set to something other than “Equal,”

changing the tuning system of the keyboard. Make sure “Equal” is selected as

the Scale in the Scale Tune page (page 127).

• Some channels do not properly play back

when playing back song data.

Make sure that playback of the relevant channel(s) is turned on (page 77).

• The Harmony function does not operate. Harmony cannot be used with the Full Keyboard or AI Full Keyboard ﬁngering

modes. Select an appropriate ﬁngering mode (page 63).

• The microphone input signal (CVP-205 only)

cannot be recorded.

This is normal; recording the audio input of the microphone is not possible.

• MIDI data is not transmitted or received via

the MIDI terminals, even when MIDI cables

are connected properly.

Make sure the HOST SELECT switch is set to “MIDI” (page 147). The MIDI

terminals cannot be used for the other switch settings.

• When a voice is changed, the previously

selected effect is changed.

Each voice has its own suitable preset values which are automatically recalled

when the corresponding Voice Set parameters are turned on (page 135).

• There is a slight difference in sound quality

between notes played on the keyboard.

• Some voices have a looping sound.

• Some noise or vibrato is noticeable at higher

pitches, depending upon the voice.

This is normal and is a result of the Clavinova’s sampling system.

• Some voices will jump an octave in pitch

when played in the upper or lower registers.

This is normal. Some voices have a pitch limit which, when reached, causes this

type of pitch shift.

• Disk save operations take a long time. This is normal. Keep in mind that it takes approximately 1 minute to save 1

megabyte of data to a ﬂoppy disk.

• The voice produces excessive noise. Certain voices may produce noise, depending on the Harmonic Content and/or

Brightness settings in the FILTER page of the Mixing Console display

(page 121).

• The sound is distorted or noisy. • The volume may be turned up too high. Make sure all relevant volume settings

are appropriate.

• This may be caused by the effects. Try canceling all unnecessary effects,

especially distortion-type effects (page 122).

• Some ﬁlter resonance settings in the Custom Voice Creator display (page 91)

can result in distorted sound. Adjust these settings if necessary.

• A strange “ﬂanging” or “doubling” sound

occurs. Also, the sound is slightly different

each time the keys are played.

Both the Main and Layer parts are set to “ON,” and both parts are set to play the

same voice. Set the Layer part to “OFF” (page 57) or change the voice for each

part (page 55).

Problem Possible Cause and Solution

159

CVP-205/203

Speciﬁcations

: available

Model Name CVP-205 CVP-203

Sound Source AWM Dynamic Stereo Sampling

Display 320 ✕ 240 dots backlit graphic LCD

Keyboard 88 keys (A-1 - C7)

Voice Polyphony (max) 96 64

Voice Selection 308 voices + 480 XG voices + 16 Drum Kits

Regular Voice 287

Sweet Voice 8

Cool Voice 2

Live Voice 1

Natural Voice 21

Sound creator

Effects

Effect Blocks

Reverb 2

Chorus 2

DSP 2

Brilliance 1 —

Effect Types

REVERB1 28+3 User

REVERB2 5

CHORUS1 21+3 User

CHORUS2 3

DSP1 101+3 User

DSP2 12

Brilliance 5 —

Accompaniment

Style

Accompaniment Styles 194 175

Session Styles 12

Pianist Styles 36

Piano Combo Styles 17

Fingering Single Finger, Fingered, Fingered On Bass, Multi Finger, AI Fingered,

Full Keyboard, AI Full Keyboard

Style Creator

OTS (One Touch Setting) Accompaniment Style

OTS link

Music Finder Approximately 2500 records

Edit

Song Format SMF (Format 0,1), ESEQ

Preset Songs

Guide Follow Lights, Any Key, Karao-Key

Guide Lamp 88 Red

Lyrics

Score —

Recording Quick Recording, Multi Track Recording, Step Recording, Song Editing

Record Channels 16

Memory

Device

Floppy Disk (2HD,2DD)

Flash Memory (internal) 1MB

Flash Availability Song (SMF), Style (SFF), Registration, Voice, etc.

Tempo Tempo Range 5 - 500

Tap Tempo

Metronome

Sound Bell on/off, Human Voices (5 languages)

Specifications

CVP-205/203

160

* Speciﬁcations and descriptions in this owner's manual are for information purposes only. Yamaha Corp. reserves the right to

change or modify products or speciﬁcations at any time without prior notice. Since speciﬁcations, equipment or options may not

be the same in every locale, please check with your Yamaha dealer.

Registration

Memory

Buttons 8

Regist Sequence

Freeze

Others Demo Function, Voice, Style

Language 6 languages (English, Japanese, German, French, Spanish, Italian)

Help

Direct Access

Piano setting button (including Piano Lock)

Master Volume

Fade In/Out

Transpose Keyboard/Song/Master

Tuning

Tuning Curve Flat/Stretch (Natural Piano Voice only)

Scale Equal Temperament, Pure Major/Pure Minor, Pythagorean, Mean Tone,

Werckmeister/Kirnberger, Arabic 1/2

Touch Response 5 level

Jacks/Connectors PHONES ✕ 2, MIDI (THRU, OUT, IN), TO HOST,

HOST SELECT, AUX PEDAL, AUX IN (L/L+R),

AUX OUT (LEVEL FIXED) (L/R), AUX OUT (L/L+R)

MIC (INPUT VOLUME,

MIC./ LINE IN),VIDEO OUT

—

Pedals Number of Pedals 3

Pedal Functions VOLUME, SUSTAIN, SOSTENUTO, SOFT, GLIDE, PORTAMENTO,

PITCHBEND, MODULATION, DSP VARIATION, VIBROTOR ON/OFF,

SONG START/STOP, STYLE START/STOP, etc.

Ampliﬁers/

Speakers

Ampliﬁers 40 W ✕ 2

Speakers (16 cm + 5 cm) ✕ 2

Dimensions [W ✕ D ✕ H]

(with the Music Stand)

1384.0 ✕ 598.2 ✕ 900.1 mm

[54-1/2" ✕ 23-9/16" ✕ 35-7/16"]

(1384.0 ✕ 598.2 ✕ 1070.0 mm)

[54-1/2" ✕ 23-9/16" ✕ 42-1/8"]

1381.5 ✕ 597.7 ✕ 899.6mm

[56-3/8" ✕ 24-3/8" ✕ 43-3/4"]

(1381.5 ✕ 597.7 ✕ 1071.2mm)

[56-3/8" ✕ 24-3/8" ✕ 36-11/16"]

Weight 80 Kg (176 lbs., 6 oz) 66 Kg (145 lbs., 8 oz)

Model Name CVP-205 CVP-203

161

CVP-205/203

Index

Numerics

1 - 16 ................................................................................. 106

[1▲▼] - [8▲▼] buttons ........................................... 18, 39–46

[A] - [J] buttons............................................................... 18, 41

Accessories ............................................................................ 6

Accompaniment Guide ........................................................ 79

Accompaniment style parts................................................... 95

[ACMP] button ............................................................... 18, 61

Adjust the Volume Balance and Changing Voices .............. 119

Adjusting the display contrast............................................... 17

Adjusting the Effects ........................................................... 122

Adjusting the Tempo ............................................................ 51

Adjusting the Volume Balance ............................................. 62

Adjusting the Volume Balance / Muting Specific Channels... 77

Adjusting values ................................................................... 47

AI ......................................................................................... 63

AI FINGERED ....................................................................... 63

AI FULL KEYBOARD ............................................................ 63

Any Key ............................................................................... 79

Append ................................................................................ 72

Applying Voice Effects.......................................................... 58

Appropriate Panel Setting for the Selected Style.................... 68

Arabic ................................................................................ 128

Arranging the Style Pattern ................................................... 65

Assembling an Accompaniment Style................................. 113

ATTACK ............................................................................... 91

AUTO .................................................................................. 20

Auto Revoice...................................................................... 120

[AUTO FILLIN] button.................................................... 18, 67

Automatically Changing One Touch Settings

with the Sections............................................................... 69

AUX IN [L / L+R] [R] jacks............................................ 19, 145

AUX OUT (LEVEL FIXED) [L] [R] jacks.......................... 19, 145

AUX OUT [L / L+R] [R] jacks........................................ 19, 145

[AUX PEDAL] jack........................................................ 19, 146

[BACK] button.......................................................... 18, 41, 47

[BALANCE] button ......................................................... 18, 62

Bar Clear ............................................................................ 116

Bar Copy ............................................................................ 116

Basic Operations — Organizing Your Data .......................... 39

Bass...................................................................................... 95

BEAT .............................................................................. 71, 72

[BREAK] button .............................................................. 18, 65

BRIGHTNESS ....................................................................... 91

Calling Up Ideal Setups for Your Music ................................ 70

Cent ................................................................................... 127

Change the Rhythmic Feel.................................................. 114

Changing Pitch-related Settings .......................................... 121

Changing the Automatically Selected Voice Settings .......... 135

Changing the Icon ................................................................ 47

Changing the Tone of the Voice ......................................... 121

Changing the Touch Sensitivity and Transpose ................... 133

Channel ................................................. 62, 77, 103, 116, 129

Channel Messages.............................................................. 149

Channel Muting ................................................................... 62

[CHANNEL ON / OFF] button ..................................18, 62, 77

Channel Transpose .............................................................105

CHD...................................................................................107

Chord ...................................................................................95

Chord Detect ......................................................................139

Chord Events.......................................................................107

Chord Fingering............................................................63, 131

Chord Tutor ........................................................................131

Chord Types Recognized in the Fingered Mode....................64

Chorus................................................................................124

Clock..................................................................................138

COMMON ...........................................................................90

Compatible Song Types ........................................................74

CONFIG 1 ..........................................................................140

CONFIG 2 ..........................................................................141

Connect the power cord .......................................................17

Connecting Audio & Video Devices....................................145

Connecting external MIDI devices ......................................146

Connecting the Microphone or Guitar (CVP-205 only)........144

Connecting to a Computer..................................................146

Controller ...........................................................................131

Converting into Kanji (Japanese language) ............................46

Cool! ....................................................................................56

COPY ...................................................................................44

Copying and Formatting Disks ............................................142

Copying Files/Folders............................................................44

Copying from Disk to Disk..................................................142

Creating Accompaniment Styles..........................................109

Current Memory ...................................................................40

Customizing the Event List — Filter.....................................108

CUT......................................................................................43

CVP-203: Keyboard Stand Assembly...................................155

CVP-205/205M: Keyboard Stand Assembly.........................153

Damper pedal.................................................................19, 59

Data Compatibility..............................................................151

[DATA ENTRY] dial ........................................................18, 47

Data Types in the MIDI TRANSMIT/RECEIVE Display .........138

DECAY .................................................................................91

DELETE.................................................................................44

Delete.................................................................................104

DELETE RECORD..................................................................72

Deleting Files/Folders............................................................44

[DEMO] button.........................................................14, 18, 53

DEPTH..................................................................................91

Detailed Settings for Notation ...............................................82

[DIGITAL RECORDING] button........................14, 18, 93, 109

[DIRECT ACCESS] button................................................18, 48

Direct Access Chart ..............................................................49

Disk....................................................................................142

Disk format.........................................................................151

Disk Orchestra Collection.....................................................19

Displaying Music Notation ...................................................81

Displaying the Lyrics.............................................................84

Displaying Upper Level pages...............................................45

DOC...................................................................................152

Drum....................................................................................56

[DSP] button...........................................................18, 58, 124

Dynamics ...........................................................................115

Index

CVP-205/203

162

ECHO .......................................................................... 59, 135

EDIT................................................................................... 112

Edit the Created Accompaniment Style............................... 114

Editing a Recorded Song..................................................... 103

Editing Channel-related Parameters .................................... 103

Editing Chord Events .......................................................... 107

Editing Note Events ............................................................ 106

Editing Records .................................................................... 72

Editing System Events ......................................................... 107

Editing the Channel Data.................................................... 116

Editing Voices ...................................................................... 88

EFFECT................................................................................. 92

Effect Block ........................................................................ 123

Effect Structure ................................................................... 124

Effects................................................................................. 122

EG........................................................................................ 91

Embellish and enhance your melodies

— with the automatic Harmony and Echo effects.............. 30

END Mark .......................................................................... 101

ENDING .............................................................................. 67

[ENDING / rit.] button.............................................. 18, 31, 66

[ENTER] button .............................................................. 18, 47

Entering Characters............................................................... 46

Entering Chords and Sections (Chord Step) ......................... 100

Entering miscellaneous characters (marks)............................ 46

Entering numbers ................................................................. 46

Entering special character marks

(umlaut, accent, Japanese “ ” and “ ”) ......................... 46

Entering Your Name and Language Preference ................... 143

Equal Temperament............................................................ 128

ESEQ .................................................................................. 151

Example Keyboard Data ..................................................... 149

[EXIT] button .................................................................. 18, 41

exit from small pop-up windows .......................................... 41

[EXTRA TRACKS (STYLE)] button.................................... 18, 78

Fade In Time, Fade Out Time, Fade Out Hold Time ........... 140

[FADE IN / OUT] button................................................. 18, 66

FAVORITE............................................................................ 72

[FF] button ..................................................................... 18, 77

File....................................................................................... 40

File/Folder-related Operations .............................................. 42

Files/folders in a floppy disk ................................................. 43

Fill........................................................................................ 67

Filter..................................................................... 91, 108, 121

FINGERED ........................................................................... 63

FINGERED ON BASS............................................................ 63

First Key On ....................................................................... 102

FLOPPY DISK drive .............................................................. 40

Floppy disk drive.............................................................. 19, 6

Follow Lights........................................................................ 79

Foot Controller ............................................................. 59, 146

Footswitch.................................................................... 59, 146

Formatting a Disk ............................................................... 142

[FREEZE] button...................................................... 19, 87, 134

FULL KEYBOARD................................................................. 63

[FUNCTION] button .................................................... 18, 125

Gate Time ............................................................................ 98

GENRE ........................................................................... 71, 73

GENRE NAME...................................................................... 73

GM System Level 1....................................................... 19, 152

Groove............................................................................... 114

Groove parameters .............................................................114

[GUIDE] button ........................................................14, 18, 79

Handling the Floppy Disk Drive (FDD) and Floppy Disk.........6

Harmonic Content ................................................................91

HARMONY ............................................................59, 92, 135

Harmony Assignments ........................................................136

Harmony Types ..................................................................136

[HARMONY / ECHO] button..........................................19, 59

Headphones .................................................................17, 144

Help messages can be displayed in any one of the

following languages...........................................................50

[HELP] button .................................................................18, 50

High Key.............................................................................118

[HOST SELECT] switch .................................................19, 146

Hz ......................................................................................127

ICON SELECT .......................................................................47

[INPUT VOLUME] knob ...............................................19, 144

Inputting and Editing Lyrics.................................................108

Instant Selection of Displays .................................................48

INTRO..................................................................................67

[INTRO] button.........................................................18, 31, 65

Karao-Key.............................................................................79

Key cover..............................................................................16

KEY SIGNATURE ..................................................................82

Keyboard guide lamps ....................................................19, 79

Keyboard Percussion.............................................................56

Keyboard Touch .................................................................133

Keyboard/Panel...................................................................133

KEYWORD .....................................................................71, 72

Kirnberger...........................................................................128

Layer.....................................................................................57

Layering Two Different Voices..............................................57

LCD......................................................................................15

[LCD CONTRAST] knob .................................................18, 17

Left .......................................................................................58

LEFT CH. ..............................................................................82

[LEFT HOLD] button.......................................................19, 59

Left pedal........................................................................19, 59

Live! .....................................................................................56

Local Control......................................................................137

Loop recording ...................................................................109

Lyrics............................................................................84, 108

MAIN A/B/C/D......................................................................65

MAIN [A] button.............................................................18, 65

MAIN [B] button.............................................................18, 65

MAIN [C] button.............................................................18, 65

MAIN [D] button ............................................................18, 65

Maintaining Panel Settings..................................................134

Maintenance...........................................................................8

Making Global and Other Important Settings ......................125

Making Overall System Settings (Local Control, Clock, etc.) ...

137

Making Settings for Fade In/Out, Metronome,

Parameter Lock, and Tap.................................................140

Making Settings for the Display, Speaker System,

and Voice Number Indication .........................................141

Index

163

CVP-205/203

Making Settings for the Pedals ............................................ 131

Making Settings for the Pedals and Keyboard ..................... 131

Making Style File Format Settings ....................................... 117

Master Tune ....................................................................... 127

Mastering Your Favorite Songs.............................................. 38

[MASTER VOLUME] dial................................................ 18, 17

Mean-Tone......................................................................... 128

Measure/Beat/Clock ............................................................. 98

[MEMORY] button.......................................................... 19, 85

Message Switch.................................................................. 138

Messages................................................................................ 8

Metronome ........................................................................ 140

METRONOME [START / STOP] button........................... 18, 51

[MIC. LINE] switch ....................................................... 19, 144

[MIC. LINE IN] jack...................................................... 19, 144

MIDI .................................................................................. 137

MIDI [THRU] [OUT] [IN] terminals..............................19, 146

MIDI channels.................................................................... 150

MIDI IN.............................................................................. 146

MIDI OUT.......................................................................... 146

MIDI Receive Parts............................................................. 139

MIDI SET UP ...................................................................... 143

MIDI terminals ................................................................... 146

MIDI THRU........................................................................ 146

Mix .................................................................................... 104

[MIXING CONSOLE] button......................................... 18, 119

[MONO] button ............................................................. 19, 59

Moving Files/Folders ............................................................ 43

MULTI FINGER .................................................................... 63

Multi Recording ................................................................... 95

[MUSIC FINDER] button .................................... 15, 19, 33, 70

Music Finder Record Edit ..................................................... 72

Music Finder Search............................................................. 71

Music Stand ......................................................................... 16

Muting Specific Parts............................................................ 78

NAME .................................................................................. 42

Naming Files/Folders............................................................ 42

Natural Voices ..................................................................... 89

Natural!................................................................................ 56

NEW (FOLDER).................................................................... 45

NEW RECORD..................................................................... 73

[NEXT] button .......................................................... 18, 41, 47

Normal............................................................................... 102

Note Events ........................................................................ 106

Note for Windows users (regarding MIDI driver)................. 146

Note Limit .......................................................................... 118

NOTE NAME........................................................................ 83

NTR (Note Transposition Rule) ........................................... 117

NTT (Note Transposition Table).......................................... 118

OCTAVE ............................................................................ 121

One Touch Setting ............................................................... 32

ONE TOUCH SETTING [1] - [4] buttons .................. 19, 68, 69

One-touch Piano Play .......................................................... 56

[ON / OFF] button (POWER) .......................................... 18, 17

Open/Save displays .............................................................. 39

Organizing Files by Creating a New Folder .......................... 45

Other Parameters in the Basic Display................................ 112

Other Playback-related Operations....................................... 77

Other Settings..................................................................... 140

[OTS LINK] button.......................................................... 18, 69

Outputting the sound of an external device through the built-in

speakers of the Clavinova ............................................... 145

Overdub recording .............................................................109

Owner ................................................................................143

Pad .......................................................................................95

Parameter ...........................................................................117

Parameter Lock...................................................................141

PASTE.............................................................................43, 44

Pedal ..................................................................................131

Pedal (Center) .......................................................................59

Pedal (Left)............................................................................59

Pedal (Right) .........................................................................59

Pedal-controllable Functions...............................................132

[PHONES] jacks............................................................19, 144

Phrase...................................................................................95

Phrase Mark..................................................................77, 129

[PIANO] button ........................................................15, 19, 56

PIANO (SOUND CREATOR).................................................90

Piano Lock function..............................................................56

PITCH BEND RANGE .........................................................121

Pitch settings for each scale ................................................128

Playback of Songs.................................................................21

Playing a style.................................................................28, 60

Playing a Style’s Rhythm Channels only................................62

Playing Along with the Clavinova .........................................36

Playing and Practicing with the Songs...................................36

Playing Back Songs on Disk..................................................77

Playing Different Voices with the Left and Right Hands.........27

Playing Fill-in patterns automatically when changing

accompaniment sections ...................................................67

Playing Several Sounds Simultaneously.................................57

Playing Styles........................................................................28

Playing the Demos..........................................................20, 53

Playing the Internal Songs.....................................................75

Playing the sounds of the Clavinova through

an external audio system, and recording the sounds to

an external recorder ........................................................145

Playing Two Voices Simultaneously......................................26

Playing Voices ......................................................................25

PORTAMENTO TIME..........................................................121

Practice Functions.................................................................79

Practicing Music with the Guide Functions...........................80

PRESET drive.........................................................................40

Preset MIDI Templates........................................................137

Punch In/Out ......................................................................102

Pure Major..........................................................................128

Pure Minor..........................................................................128

Pythagorean........................................................................128

QUANTIZE...........................................................................82

Quantize.....................................................................103, 116

Quantize Size .....................................................................103

Quick Recording...................................................................94

Quick Start..........................................................................129

Realtime Recording.............................................................111

Realtime Recording Characteristics.....................................109

[REC] button ...................................................................18, 93

Rec Mode ...........................................................................102

Recalling a Registration Memory Setup.................................87

Recalling the Registered Settings...........................................87

Receive...............................................................................139

Receive Transpose ..............................................................138

Receiving MIDI Data ..........................................................139

Index

CVP-205/203

164

record .................................................................................. 70

Recording............................................................................. 37

Recording Chord Changes for the Auto Accompaniment.... 100

Recording Individual Notes .................................................. 97

Recording Melodies ............................................................. 99

Recording Your Performances and Creating Songs................ 93

Registering Panel Setups....................................................... 85

Registering the Panel Controls in One Touch Setting ............ 69

REGISTRATION BANK......................................................... 86

REGISTRATION EDIT display............................................... 86

Registration Memory ............................................................ 85

REGISTRATION MEMORY [1] – [8] buttons................... 19, 85

Registration Sequence ........................................................ 134

Regular Voices ..................................................................... 89

RELEASE............................................................................... 91

Remove Event .................................................................... 116

Repeat Playback of a Specific Range .................................... 78

[REPEAT] button............................................................. 18, 78

Replace ................................................................................ 72

Resonance............................................................................ 91

Restoring the Factory-programmed Settings

of the CVP-205/203 ........................................................ 143

[REVERB] button............................................................. 18, 58

Reverb................................................................................ 124

[REW] button ................................................................. 18, 77

Rhythm ................................................................................ 95

RIGHT CH. .......................................................................... 82

Root ................................................................................... 139

RTR (Retrigger Rule) ........................................................... 118

SAVE .................................................................................... 45

Save ............................................................................... 39, 45

Saving Files .......................................................................... 45

Saving Your Registration Memory Setups.............................. 86

Scale .................................................................................. 128

Scale Tune ......................................................................... 127

Score (CVP-205 only) ........................................................... 81

Searching the Ideal Setups.................................................... 71

Searching the Music Finder Records..................................... 34

Section button indications — [BREAK], [INTRO], [MAIN],

[ENDING] buttons ............................................................ 65

sections ................................................................................ 30

Select the Recording Options: Starting, Stopping,

Punching In/Out ............................................................. 102

Selecting a Scale ................................................................ 127

Selecting a Voice.................................................................. 55

Selecting Files and Folders ................................................... 41

Selecting Intro and Ending Types.......................................... 67

Selecting items ..................................................................... 47

Selecting the Freeze Settings................................................. 87

Sequence Format................................................................ 151

sequencer........................................................................... 149

Set Up ................................................................................ 105

Setting Auto Accompaniment-related Parameters ............... 130

Setting Chord Channels ...................................................... 139

Setting Harmony and Echo ................................................. 135

Setting Root Note Channels................................................ 139

Setting Separate Voices for the Left and Right Sections

of the Keyboard ................................................................ 58

Setting Song-related Parameters.......................................... 129

Setting the Fingering Method.............................................. 131

Setting the Level Balance and Voice................................... 120

Setting the MIDI Parameters ............................................... 137

Setting the Registration Sequence, Freeze, and Voice Set ... 134

Setting the volume................................................................ 17

SFX....................................................................................... 56

Sheet Music Braces (CVP-205 only) ......................................16

Showing the Clavinova Display on a TV .....................136, 145

Simultaneously Playing a Song and an

Accompaniment Style........................................................76

SINGLE FINGER....................................................................63

SMF (Standard MIDI File)....................................................151

Song ...............................................................................14, 74

SONG [START / STOP] button........................................18, 75

SONG AUTO REVOICE......................................................120

Song Book ......................................................................22, 74

Song Creator.........................................................................93

Song Playback ..........................................................21, 74, 75

Song Recording.....................................................................93

Song Settings.......................................................................129

Sostenuto pedal ..............................................................19, 59

SOUND (SOUND CREATOR)...............................................90

SOUND CREATOR Parameters.............................................89

[SOUND CREATOR] button ...........................................18, 88

Source Root/Chord..............................................................117

Specifying the Order for Calling Up Registration Memory

Presets.............................................................................134

SPEED...................................................................................91

Split Point ...........................................................................130

Step Record ..........................................................................97

Step Record (Chord)............................................................100

Step Record (Note)................................................................99

Step Recording....................................................................112

Stopping the Style Playback While Releasing Keys................66

Style................................................................................14, 60

STYLE [START / STOP] button.........................................18, 61

Style Creator .......................................................................109

Style File.......................................................................19, 151

Style File Format .................................................................110

Style Sections........................................................................30

Style Setting ........................................................................130

sustain ..................................................................................91

Sweet!...................................................................................56

[SYNC.START] button.....................................................18, 61

[SYNC.STOP] button.......................................................18, 66

SYS/EX. (System Exclusive)..................................................107

System ................................................................................137

System Events .....................................................................107

System Messages.................................................................150

System Reset.......................................................................143

SYSTEM SET UP..................................................................143

Tap Count...........................................................................141

[TAP TEMPO] button ......................................................18, 52

TEMPO [

E] [ ] buttons..............................................18, 51

TEMPO FROM......................................................................71

Tempo Indications — MAIN Display ....................................52

TEMPO TO...........................................................................71

[TO HOST] terminal .......................................15, 19, 146, 147

[TOP] button...................................................................18, 77

[TRACK 1 (R)] button ......................................................18, 78

[TRACK 2 (L)] button.......................................................18, 78

Transmit..............................................................................138

Transmit Clock....................................................................138

Transmitting MIDI Data ......................................................138

TRANSPOSE [

E] [ ] buttons ....................................18, 133

Transpose Assign ................................................................133

Tune ...................................................................................121

TUNING.............................................................................121

Tuning the Overall Pitch.....................................................127

Index

165

CVP-205/203

UP........................................................................................ 45

USER drive ........................................................................... 40

USER EFFECT ............................................................. 123, 143

Using the USB terminal on your computer with a USB/MIDI

interface (UX256, etc.) .................................................... 148

Using Your Clavinova with Other Devices ......................... 144

Utility................................................................................. 140

[VARIATION] button...................................................... 19, 58

Velocity........................................................................ 98, 115

Velocity Change................................................................. 116

VIBRATO ............................................................................. 91

[VIDEO OUT] jack............................................... 19, 136, 145

Voice Allocation Format..................................................... 152

VOICE buttons ......................................................... 15, 19, 55

Voice Characteristics............................................................ 56

Voice Effects......................................................................... 58

VOICE PART ON / OFF [LAYER] button ......................... 18, 57

VOICE PART ON / OFF [LEFT] button ............................ 18, 57

Voice Set............................................................................ 135

Volume/Voice .................................................................... 120

Werckmeister ..................................................................... 128

What You Can Do With MIDI ............................................ 150

What’s MIDI? ..................................................................... 148

XF ................................................................................ 19, 151

XG ............................................................................... 19, 152

IMPORTANT SAFETY INSTRUCTIONS

INFORMATION RELATING TO PERSONAL INJURY, ELECTRICAL SHOCK,

AND FIRE HAZARD POSSIBILITIES HAS BEEN INCLUDED IN THIS LIST.

WARNING- When using any electrical or electronic product,

basic precautions should always be followed. These precautions

include, but are not limited to, the following:

1. Read all Safety Instructions, Installation Instructions, Spe-

cial Message Section items, and any Assembly Instructions

found in this manual BEFORE making any connections, includ-

ing connection to the main supply.

2. Main Power Supply Veriﬁcation: Yamaha products are

manufactured speciﬁcally for the supply voltage in the area

where they are to be sold. If you should move, or if any doubt

exists about the supply voltage in your area, please contact your

dealer for supply voltage veriﬁcation and (if applicable) instruc-

tions. The required supply voltage is printed on the name plate.

For name plate location, please refer to the graphic found in the

Special Message Section of this manual.

3. This product may be equipped with a polarized plug (one

blade wider than the other). If you are unable to insert the plug

into the outlet, turn the plug over and try again. If the problem

persists, contact an electrician to have the obsolete outlet

replaced. Do NOT defeat the safety purpose of the plug.

4. Some electronic products utilize external power supplies

or adapters. Do NOT connect this type of product to any power

supply or adapter other than one described in the owners manual,

on the name plate, or speciﬁcally recommended by Yamaha.

5. WARNING: Do not place this product or any other

objects on the power cord or place it in a position where anyone

could walk on, trip over, or roll anything over power or connect-

ing cords of any kind. The use of an extension cord is not recom-

mended! If you must use an extension cord, the minimum wire

size for a 25’ cord (or less) is 18 AWG. NOTE: The smaller the

AWG number, the larger the current handling capacity. For

longer extension cords, consult a local electrician.

6. Ventilation: Electronic products, unless speciﬁcally

designed for enclosed installations, should be placed in locations

that do not interfere with proper ventilation. If instructions for

enclosed installations are not provided, it must be assumed that

unobstructed ventilation is required.

7. Temperature considerations: Electronic products should

be installed in locations that do not signiﬁcantly contribute to

their operating temperature. Placement of this product close to

heat sources such as; radiators, heat registers and other devices

that produce heat should be avoided.

8. This product was NOT designed for use in wet/damp loca-

tions and should not be used near water or exposed to rain.

Examples of wet/damp locations are; near a swimming pool, spa,

tub, sink, or wet basement.

9. This product should be used only with the components

supplied or; a cart, rack, or stand that is recommended by the

manufacturer. If a cart, rack, or stand is used, please observe all

safety markings and instructions that accompany the accessory

product.

10. The power supply cord (plug) should be disconnected

from the outlet when electronic products are to be left unused for

extended periods of time. Cords should also be disconnected

when there is a high probability of lightning and/or electrical

storm activity.

11. Care should be taken that objects do not fall and liquids are

not spilled into the enclosure through any openings that may exist.

12. Electrical/electronic products should be serviced by a

qualiﬁed service person when:

a. The power supply cord has been damaged; or

b. Objects have fallen, been inserted, or liquids have been

spilled into the enclosure through openings; or

c. The product has been exposed to rain: or

d. The product dose not operate, exhibits a marked change

in performance; or

e. The product has been dropped, or the enclosure of the

product has been damaged.

13. Do not attempt to service this product beyond that

described in the user-maintenance instructions. All other servic-

ing should be referred to qualiﬁed service personnel.

14. This product, either alone or in combination with an

ampliﬁer and headphones or speaker/s, may be capable of pro-

ducing sound levels that could cause permanent hearing loss. DO

NOT operate for a long period of time at a high volume level or

at a level that is uncomfortable. If you experience any hearing

loss or ringing in the ears, you should consult an audiologist.

IMPORTANT: The louder the sound, the shorter the time period

before damage occurs.

15. Some Yamaha products may have benches and/or accessory

mounting ﬁxtures that are either supplied as a part of the product

or as optional accessories. Some of these items are designed to be

dealer assembled or installed. Please make sure that benches are

stable and any optional ﬁxtures (where applicable) are well

secured BEFORE using. Benches supplied by Yamaha are

designed for seating only. No other uses are recommended.

PLEASE KEEP THIS MANUAL

92-469-2

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)

(2 wires)

• This applies only to products distributed by Yamaha-Kemble Music

(U.K.) Ltd.

(polarity)

• This applies only to products distributed by Yamaha Canada Music

Ltd.

• Ceci ne s’applique qu’aux produits distribués par Yamaha Canada

Musique Ltée.

FCC INFORMATION (U.S.A.)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instruc-

tions contained in this manual, meets FCC require-

ments. Modiﬁcations not expressly approved by

Yamaha may void your authority, granted by the FCC, to

use the product.

2. IMPORTANT: When connecting this product to acces-

sories and/or another product use only high quality

shielded cables. Cable/s supplied with this product

MUST be used. Follow all installation instructions. Fail-

ure to follow instructions could void your FCC authori-

zation to use this product in the USA.

3. NOTE: This product has been tested and found to com-

ply with the requirements listed in FCC Regulations,

Part 15 for Class “B” digital devices. Compliance with

these requirements provides a reasonable level of

assurance that your use of this product in a residential

environment will not result in harmful interference with

other electronic devices. This equipment generates/

uses radio frequencies and, if not installed and used

according to the instructions found in the users manual,

may cause interference harmful to the operation of

other electronic devices. Compliance with FCC regula-

tions does not guarantee that interference will not occur

in all installations. If this product is found to be the

source of interference, which can be determined by

turning the unit “OFF” and “ON”, please try to eliminate

the problem by using one of the following measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line ﬁlter/s.

In the case of radio or TV interference, relocate/reorient

the antenna. If the antenna lead-in is 300 ohm ribbon

lead, change the lead-in to co-axial type cable.

If these corrective measures do not produce satisfac-

tory results, please contact the local retailer authorized

to distribute this type of product. If you can not locate

the appropriate retailer, please contact Yamaha Corpo-

ration of America, Electronic Service Division, 6600

Orangethorpe Ave, Buena Park, CA90620

The above statements apply ONLY to those products

distributed by Yamaha Corporation of America or its

subsidiaries.

IMPORTANT NOTICE FOR THE UNITED KINGDOM

Connecting the Plug and Cord

IMPORTANT. The wires in this mains lead are coloured in

accordance with the following code:

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead of this appa-

ratus may not correspond with the coloured makings iden-

tifying the terminals in your plug proceed as follows:

The wire which is coloured BLUE must be connected to

the terminal which is marked with the letter N or coloured

BLACK.

The wire which is coloured BROWN must be connected to

the terminal which is marked with the letter L or coloured

RED.

Making sure that neither core is connected to the earth ter-

minal of the three pin plug.

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH

WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

ATTENTION: POUR ÉVITER LES CHOCS ÉLEC-

TRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE

LA FICHE DANS LA BORNE CORRESPONDANTE DE LA

PRISE ET POUSSER JUSQU’AU FOND.

For details of products, please contact your nearest Yamaha or the

authorized distributor listed below.

Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou

au distributeur le plus proche de vous ﬁgurant dans la liste suivante.

Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten

Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen

Bestimmungsländern erhältlich.

Para detalles sobre productos, contacte su tienda Yamaha más cercana

o el distribuidor autorizado que se lista debajo.

CANADA

Yamaha Canada Music Ltd.

135 Milner Avenue, Scarborough, Ontario,

M1S 3R1, Canada

Tel: 416-298-1311

U.S.A.

Yamaha Corporation of America

6600 Orangethorpe Ave., Buena Park, Calif. 90620,

U.S.A.

Tel: 714-522-9011

MEXICO

Yamaha de Mexico S.A. De C.V.,

Departamento de ventas

Javier Rojo Gomez No.1149, Col. Gpe Del

Moral, Deleg. Iztapalapa, 09300 Mexico, D.F.

Tel: 686-00-33

BRAZIL

Yamaha Musical do Brasil LTDA.

Av. Rebouças 2636, São Paulo, Brasil

Tel: 011-853-1377

ARGENTINA

Yamaha de Panamá S.A. Sucursal de Argentina

Viamonte 1145 Piso2-B 1053,

Buenos Aires, Argentina

Tel: 1-4371-7021

PANAMA AND OTHER LATIN

AMERICAN COUNTRIES/

CARIBBEAN COUNTRIES

Yamaha de Panamá S.A.

Torre Banco General, Piso 7, Urbanización Marbella,

Calle 47 y Aquilino de la Guardia,

Ciudad de Panamá, Panamá

Tel: 507-269-5311

THE UNITED KINGDOM

Yamaha-Kemble Music (U.K.) Ltd.

Sherbourne Drive, Tilbrook, Milton Keynes,

MK7 8BL, England

Tel: 01908-366700

IRELAND

Danfay Ltd.

61D, Sallynoggin Road, Dun Laoghaire, Co. Dublin

Tel: 01-2859177

GERMANY/SWITZERLAND

Yamaha Europa GmbH.

Siemensstraße 22-34, 25462 Rellingen,

F.R. of Germany

Tel: 04101-3030

AUSTRIA

Yamaha Music Austria

Schleiergasse 20, A-1100 Wien Austria

Tel: 01-60203900

THE NETHERLANDS

Yamaha Music Nederland

Kanaalweg 18G, 3526KL, Utrecht, The Netherlands

Tel: 030-2828411

BELGIUM

Yamaha Music Belgium

Keiberg Imperiastraat 8, 1930 Zaventem, Belgium

Tel: 02-7258220

FRANCE

Yamaha Musique France,

Division Claviers

BP 70-77312 Marne-la-Vallée Cedex 2, France

Tel: 01-64-61-4000

ITALY

Yamaha Musica Italia S.P.A.

Viale Italia 88, 20020 Lainate (Milano), Italy

Tel: 02-935-771

SPAIN/PORTUGAL

Yamaha-Hazen Electronica Musical, S.A.

Ctra. de la Coruna km. 17, 200, 28230

Las Rozas (Madrid) Spain

Tel: 91-201-0700

GREECE

Philippe Nakas S.A.

Navarinou Street 13, P.Code 10680, Athens, Greece

Tel: 01-364-7111

SWEDEN

Yamaha Scandinavia AB

J. A. Wettergrens Gata 1

Box 30053

S-400 43 Göteborg, Sweden

Tel: 031 89 34 00

DENMARK

YS Copenhagen Liaison Ofﬁce

Generatorvej 8B

DK-2730 Herlev, Denmark

Tel: 44 92 49 00

FINLAND

F-Musiikki Oy

Kluuvikatu 6, P.O. Box 260,

SF-00101 Helsinki, Finland

Tel: 09 618511

NORWAY

Norsk ﬁlial av Yamaha Scandinavia AB

Grini Næringspark 1

N-1345 Østerås, Norway

Tel: 67 16 77 70

ICELAND

Skifan HF

Skeifan 17 P.O. Box 8120

IS-128 Reykjavik, Iceland

Tel: 525 5000

OTHER EUROPEAN COUNTRIES

Yamaha Europa GmbH.

Siemensstraße 22-34, 25462 Rellingen,

F.R. of Germany

Tel: 04101-3030

Yamaha Corporation,

Asia-Paciﬁc Music Marketing Group

Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650

Tel: 053-460-2312

TURKEY/CYPRUS

Yamaha Europa GmbH.

Siemensstraße 22-34, 25462 Rellingen,

F.R. of Germany

Tel: 04101-3030

OTHER COUNTRIES

Yamaha Music Gulf FZE

LB21-128 Jebel Ali Freezone

P.O.Box 17328, Dubai, U.A.E.

Tel: 971-4-881-5868

HONG KONG

Tom Lee Music Co., Ltd.

11/F., Silvercord Tower 1, 30 Canton Road,

Tsimshatsui, Kowloon, Hong Kong

Tel: 2737-7688

INDONESIA

PT. Yamaha Music Indonesia (Distributor)

PT. Nusantik

Gedung Yamaha Music Center, Jalan Jend. Gatot

Subroto Kav. 4, Jakarta 12930, Indonesia

Tel: 21-520-2577

KOREA

Yamaha Music Korea Ltd.

Tong-Yang Securities Bldg. 16F 23-8 Yoido-dong,

Youngdungpo-ku, Seoul, Korea

Tel: 02-3770-0661

MALAYSIA

Yamaha Music Malaysia, Sdn., Bhd.

Lot 8, Jalan Perbandaran, 47301 Kelana Jaya,

Petaling Jaya, Selangor, Malaysia

Tel: 3-703-0900

PHILIPPINES

Yupangco Music Corporation

339 Gil J. Puyat Avenue, P.O. Box 885 MCPO,

Makati, Metro Manila, Philippines

Tel: 819-7551

SINGAPORE

Yamaha Music Asia Pte., Ltd.

11 Ubi Road #06-00, Meiban Industrial Building,

Singapore

Tel: 65-747-4374

TAIWAN

Yamaha KHS Music Co., Ltd.

10F, 150, Tun-Hwa Northroad,

Taipei, Taiwan, R.O.C.

Tel: 02-2713-8999

THAILAND

Siam Music Yamaha Co., Ltd.

121/60-61 RS Tower 17th Floor,

Ratchadaphisek RD., Dindaeng,

Bangkok 10320, Thailand

Tel: 02-641-2951

THE PEOPLE’S REPUBLIC OF CHINA

AND OTHER ASIAN COUNTRIES

Yamaha Corporation,

Asia-Paciﬁc Music Marketing Group

Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650

Tel: 053-460-2317

AUSTRALIA

Yamaha Music Australia Pty. Ltd.

Level 1, 99 Queensbridge Street, Southbank, Victoria

3006, Australia

Tel: 3-9693-5111

NEW ZEALAND

Music Houses of N.Z. Ltd.

146/148 Captain Springs Road, Te Papapa,

Auckland, New Zealand

Tel: 9-634-0099

COUNTRIES AND TRUST

TERRITORIES IN PACIFIC OCEAN

Yamaha Corporation,

Asia-Paciﬁc Music Marketing Group

Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650

Tel: 053-460-2312

NORTH AMERICA

CENTRAL & SOUTH AMERICA

EUROPE

AFRICA

MIDDLE EAST

ASIA

OCEANIA

HEAD OFFICE Yamaha Corporation, Pro Audio & Digital Musical Instrument Division

Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650

Tel: 053-460-3273

[CL] 23

M.D.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation

??????? ???AP???.?-03C0

Printed in Indonesia

Clavinova Web site (English only)

http://www.yamahaclavinova.com/

Yamaha Manual Library (English version only)

http://www2.yamaha.co.jp/manual/english/

Documenttranscriptie

CVP-205/205M/203 OWNER’S OWNER’S MANUAL MANUAL SPECIAL MESSAGE SECTION PRODUCT SAFETY MARKINGS: Yamaha electronic products may have either labels similar to the graphics shown below or molded/stamped facsimiles of these graphics on the enclosure. The explanation of these graphics appears on this page. Please observe all cautions indicated on this page and those indicated in the safety instruction section. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. See bottom of Keyboard enclosure for graphic symbol markings. The exclamation point within the equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. The lightning flash with arrowhead symbol, within the equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electrical shock. IMPORTANT NOTICE: All Yamaha electronic products are tested and approved by an independent safety testing laboratory in order that you may be sure that when it is properly installed and used in its normal and customary manner, all foreseeable risks have been eliminated. DO NOT modify this unit or commission others to do so unless specifically authorized by Yamaha. Product performance and/or safety standards may be diminished. Claims filed under the expressed warranty may be denied if the unit is/has been modified. Implied warranties may also be affected. SPECIFICATIONS SUBJECT TO CHANGE: The information contained in this manual is believed to be correct at the time of printing. However, Yamaha reserves the right to change or modify any of the specifications without notice or obligation to update existing units. ENVIRONMENTAL ISSUES: Yamaha strives to produce products that are both user safe and environmentally friendly. We sincerely believe that our products and the production methods used to produce them, meet these goals. In keeping with both the letter and the spirit of the law, we want you to be aware of the following: 92-469 1 (bottom) Battery Notice: This product MAY contain a small non- rechargable battery which (if applicable) is soldered in place. The average life span of this type of battery is approximately five years. When replacement becomes necessary, contact a qualified service representative to perform the replacement. Warning: Do not attempt to recharge, disassemble, or incinerate this type of battery. Keep all batteries away from children. Dispose of used batteries promptly and as regulated by applicable laws. Note: In some areas, the servicer is required by law to return the defective parts. However, you do have the option of having the servicer dispose of these parts for you. Disposal Notice: Should this product become damaged beyond repair, or for some reason its useful life is considered to be at an end, please observe all local, state, and federal regulations that relate to the disposal of products that contain lead, batteries, plastics, etc. NOTICE: Service charges incurred due to lack of knowl- edge relating to how a function or effect works (when the unit is operating as designed) are not covered by the manufacturer’s warranty, and are therefore the owners responsibility. Please study this manual carefully and consult your dealer before requesting service. NAME PLATE LOCATION: The graphic below indicates the location of the name plate. The model number, serial number, power requirements, etc., are located on this plate. You should record the model number, serial number, and the date of purchase in the spaces provided below and retain this manual as a permanent record of your purchase. CVP-205 Model Serial No. Purchase Date CVP-203 PRECAUTIONS PLEASE READ CAREFULLY BEFORE PROCEEDING * Please keep this manual in a safe place for future reference. WARNING Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following: Power supply/Power cord Water warning • Only use the voltage specified as correct for the instrument. The • • • • Do not expose the instrument to rain, use it near water or in required voltage is printed on the name plate of the instrument. Check the electric plug periodically and remove any dirt or dust which may have accumulated on it. Use only the supplied power cord/plug. Do not place the power cord near heat sources such as heaters or radiators, and do not excessively bend or otherwise damage the cord, place heavy objects on it, or place it in a position where anyone could walk on, trip over, or roll anything over it. • damp or wet conditions, or place containers on it containing liquids which might spill into any openings. Never insert or remove an electric plug with wet hands. Fire warning • Do not put burning items, such as candles, on the unit. A burning item may fall over and cause a fire. If you notice any abnormality Do not open • If the power cord or plug becomes frayed or damaged, or if there • Do not open the instrument or attempt to disassemble the inter- is a sudden loss of sound during use of the instrument, or if any unusual smells or smoke should appear to be caused by it, immediately turn off the power switch, disconnect the electric plug from the outlet, and have the instrument inspected by qualified Yamaha service personnel. nal parts or modify them in any way. The instrument contains no user-serviceable parts. If it should appear to be malfunctioning, discontinue use immediately and have it inspected by qualified Yamaha service personnel. CAUTION Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the instrument or other property. These precautions include, but are not limited to, the following: Power supply/Power cord Location • When removing the electric plug from the instrument or an outlet, • • • Do not expose the instrument to excessive dust or vibrations, or always hold the plug itself and not the cord. Pulling by the cord can damage it. Remove the electric plug from the outlet when the instrument is not to be used for extended periods of time, or during electrical storms. Do not connect the instrument to an electrical outlet using a multiple-connector. Doing so can result in lower sound quality, or possibly cause overheating in the outlet. • • • • Assembly • Read carefully the attached documentation explaining the extreme cold or heat (such as in direct sunlight, near a heater, or in a car during the day) to prevent the possibility of panel disfiguration or damage to the internal components. Do not use the instrument in the vicinity of a TV, radio, stereo equipment, mobile phone, or other electric devices. Otherwise, the instrument, TV, or radio may generate noise. Do not place the instrument in an unstable position where it might accidentally fall over. Before moving the instrument, remove all connected cables. Do not place the instrument against a wall (allow at least 3 cm/ one-inch from the wall), since this can cause inadequate air circulation, and possibly result in the instrument overheating. assembly process. Failure to assemble the instrument in the proper sequence might result in damage to the instrument or even injury. (1)B-7 1/2 CVP-205/203 3 Connections Using the bench (If included) • Before connecting the instrument to other electronic compo- • Do not place the bench in an unstable position where it might nents, turn off the power for all components. Before turning the power on or off for all components, set all volume levels to minimum. Also, be sure to set the volumes of all components at their minimum levels and gradually raise the volume controls while playing the instrument to set the desired listening level. accidentally fall over. • Do not play carelessly with or stand on the bench. Using it as a • • Maintenance • When cleaning the instrument, use a soft, dry or slightly damp cloth. Do not use paint thinners, solvents, cleaning fluids, or chemical-impregnated wiping cloths. Saving data Saving and backing up your data Handling caution • Current memory data (see page 40) is lost when you turn off the • Take care that the key cover does not pinch your fingers, and do • • • • tool or step-ladder or for any other purpose might result in accident or injury. Only one person should sit on the bench at a time, in order to prevent the possibility of accident or injury. If the bench screws become loose due to extensive long-term use, tighten them periodically using the included tool. power to the instrument. Save the data to a floppy disk/the User Drive (see page 40). Saved data may be lost due to malfunction or incorrect operation. Save important data to a floppy disk. not insert a finger or hand in any gaps on the key cover or instrument. Never insert or drop paper, metallic, or other objects into the gaps on the key cover, panel or keyboard. If this happens, turn off the power immediately and unplug the power cord from the AC outlet. Then have the instrument inspected by qualified Yamaha service personnel. Do not place vinyl, plastic or rubber objects on the instrument, since this might discolor the panel or keyboard. Do not rest your weight on, or place heavy objects on the instrument, and do not use excessive force on the buttons, switches or connectors. Do not operate the instrument for a long period of time at a high or uncomfortable volume level, since this can cause permanent hearing loss. If you experience any hearing loss or ringing in the ears, consult a physician. When you change settings in a display page and then exit from that page, System Setup data (listed in the Parameter Chart of the separate Data List booklet) is automatically stored. However, this edited data is lost if you turn off the power without properly exiting from the relevant display. Backing up the floppy disk • To protect against data loss through media damage, we recommend that you save your important data onto two floppy disks. Yamaha cannot be held responsible for damage caused by improper use or modifications to the instrument, or data that is lost or destroyed. Always turn the power off when the instrument is not in use. (1)B-7 4 CVP-205/203 2/2 Thank you for purchasing the Yamaha Clavinova! We recommend that you read this manual carefully so that you can fully take advantage of the advanced and convenient functions of the Clavinova. We also recommend that you keep this manual in a safe and handy place for future reference. About this Owner’s Manual and Data List This manual consists of four main sections: Introduction, Quick Guide, Basic Operation, and Reference. Also, a separate Data List is provided. Introduction (page 2): Please read this section first. Quick Guide (page 20): This section explains how to use the basic functions. Basic Operation (page 39): This section explains how to use the basic operations including display-based controls. Reference (page 53): This section explains how to make detailed settings for the Clavinova’s various functions. Data List : Voice List, MIDI Data Format, etc. * The models CVP-205/205M/203 will be referred to as the CVP/Clavinova in this Owner’s Manual. * The illustrations and LCD screens as shown in this owner’s manual are for instructional purposes only, and may appear somewhat different from those on your instrument. * The example Operation Guide displays shown in this Manual are taken from the CVP-205, and in English. * The bitmap fonts used in this instrument have been provided by and are the property of Ricoh co., Ltd. * Copying of the commercially available software is strictly prohibited except for your personal use. This product incorporates and bundles computer programs and contents in which Yamaha owns copyrights or with respect to which it has license to use others’ copyrights. Such copyrighted materials include, without limitation, all computer software, styles files, MIDI files, WAVE data and sound recordings. Any unauthorized use of such programs and contents outside of personal use is not permitted under relevant laws. Any violation of copyright has legal consequences. DON’T MAKE, DISTRIBUTE OR USE ILLEGAL COPIES. Trademarks: • Apple and Macintosh are trademarks of Apple Computer, Inc. • IBM-PC/AT is a trademark of International Business Machines Corporation. • Windows is the registered trademark of Microsoft® Corporation. • All other trademarks are the property of their respective holders. CVP-205/203 5 Accessories ■ “Music Software Collection” Disk (and Music Book) (CVP-203 only) This disk features sample songs that you can play back on your Clavinova. ■ “50 greats for the Piano” Disk (and Music Book) ■ Recording disk Use this blank disk to save your performance. ■ Owner’s Manual This manual contains complete instructions for operating your Clavinova. ■ Data List This manual contains lists of voices, styles and parameters, etc. ■ Bench A bench may be included or optional, depending on your locale. Handling the Floppy Disk Drive (FDD) and Floppy Disk Precautions Be sure to handle floppy disks and treat the disk drive with care. Follow the important precautions below. Compatible Disk Type • 3.5" 2DD and 2HD type floppy disks can be used. Inserting/Ejecting Floppy Disks To insert a floppy disk into the disk drive: • Hold the disk so that the label of the disk is facing upward and the sliding shutter is facing forward, towards the disk slot. Carefully insert the disk into the slot, slowly pushing it all the way in until it clicks into place and the eject button pops out. Drive lamp When the power is turned on, the drive lamp (at the bottom left of the drive) lights to indicate the drive can be used. 6 CVP-205/203 To eject a floppy disk: Before ejecting the disk, be sure to confirm that data is not being written to the floppy disk. If data is currently being written to the floppy disk in the following operations, the messages “Now executing,” “Now copying,” and “Now formatting” appears in the display. • Moving, copying, pasting, saving, or deleting data (page 43 - 45). • Naming files and folders (page 42); creating a new folder (page 45). • Copying a disk to an another disk (page 142); formatting the disk (page 142). Eject button • Never attempt to remove the disk or turn the power off when the data is being written to the floppy disk. Doing so can damage the disk and possibly the disk drive. Press the eject button slowly as far as it will go; the disk will automatically pop out. When the disk is fully ejected, carefully remove it by hand. • If the eject button is pressed too quickly, or if it is not pressed in as far as it will go, the disk may not eject properly. The eject button may become stuck in a halfpressed position with the disk extending from the drive slot by only a few millimeters. If this happens, do not attempt to pull out the partially ejected disk, since using force in this situation can damage the disk drive mechanism or the floppy disk. To remove a partially ejected disk, try pressing the eject button once again, or push the disk back into the slot and then repeat the eject procedure. • Be sure to remove the floppy disk from the disk drive before turning off the power. A floppy disk left in the drive for extended periods can easily pick up dust and dirt that can cause data read and write errors. • Never use a floppy disk with a deformed shutter or housing. • Do not attach anything other than the provided labels to a floppy disk. Also make sure that labels are attached in the proper location. To protect your data (Write-protect Tab): • To prevent accidental erasure of important data, slide the disk’s write-protect tab to the “protect” position (tab open). write-protect tab open (protect position) Data backup Cleaning the Disk Drive Read/Write Head • Clean the read/write head regularly. This instrument employs a precision magnetic read/write head which, after an extended period of use, will pick up a layer of magnetic particles from the disks used that will eventually cause read and write errors. • To maintain the disk drive in optimum working order Yamaha recommends that you use a commerciallyavailable dry-type head cleaning disk to clean the head about once a month. Ask your Yamaha dealer about the availability of proper head-cleaning disks. • Never insert anything but floppy disks into the disk drive. Other objects may cause damage to the disk drive or floppy disks. • For maximum data security Yamaha recommends that you keep two copies of important data on separate floppy disks. This gives you a backup if one disk is lost or damaged. To make a backup disk use the Disk to Disk function on page 142. About the Floppy Disks To handle floppy disks with care: • Do not place heavy objects on a disk or bend or apply pressure to the disk in any way. Always keep floppy disks in their protective cases when they are not in use. • Do not expose the disk to direct sunlight, extremely high or low temperatures, or excessive humidity, dust or liquids. • Do not open the sliding shutter and touch the exposed surface of the floppy disk inside. • Do not expose the disk to magnetic fields, such as those produced by televisions, speakers, motors, etc., since magnetic fields can partially or completely erase data on the disk, rendering it unreadable. CVP-205/203 7 About the Display Messages A message (information or confirmation dialog) sometimes appears on the screen to facilitate operation. When such messages appear, simply follow the instructions as shown by pressing the corresponding button. You can select the desired language from the Help display (page 50). For this example, press the [G] (YES) button to execute formatting. “The Clavinova-Computer Connection” is a supplementary guidebook that describes, for beginners, what you can do with your Clavinova and a personal computer and how to set up a Clavinova-Computer system (the manual is not written for any specific models). The document is available as a PDF file (in English) at the following Internet address: Clavinova Home Page .......................... http://www.yamahaclavinova.com/ Yamaha Manual Library (Electronic Musical Instruments) ......... http://www2.yamaha.co.jp/manual/english/ Maintenance Clean the instrument using a dry, soft cloth or slightly damp, soft cloth (wring well). CAUTION Do not use benzine, thinner, detergent, or chemical cloth for cleaning. Do not place vinyl, plastic, or rubber products on the instrument. Otherwise, the panel or keys may be discolored or degraded. CAUTION Before using the Clavinova, be sure to read “Precautions” on pages 3 - 4. ■ Tuning Unlike an acoustic piano, the Clavinova does not need to be tuned. It always stays perfectly in tune. ■ Transporting If you move to another location, you can transport the Clavinova along with other belongings. You can move the unit as it is (assembled) or you can disassemble the unit down to the condition it was in when you first took it out of the box. Transport the keyboard horizontally. Do not lean it up against a wall or stand it up on its side. Do not subject the instrument to excessive vibration or shock. 8 CVP-205/203 Table of Contents Introduction SPECIAL MESSAGE SECTION ................................... 2 PRECAUTIONS .......................................................... 3 About this Owner’s Manual and Data List .............. 5 Accessories ............................................................... 6 Handling the Floppy Disk Drive (FDD) and Floppy Disk..................................................... 6 About the Display Messages.................................... 8 Maintenance ............................................................ 8 Application Index ................................................... 12 What can you do with the Clavinova?................... 14 Setting Up the Clavinova ....................................... 16 Key cover ................................................................................ 16 Music Stand ............................................................................ 16 Sheet Music Braces (CVP-205 only) ......................................... 16 Turning the Power On and Off................................................ 17 Using headphones .................................................................. 17 Panel Controls and Terminals................................ 18 Quick Guide Playing the Demos ................................................. 20 Song Playback ........................................................ 21 Using the [DATA ENTRY] Dial ................................ 47 Direct Access — Instant Selection of Displays ....... 48 Help Messages........................................................ 50 Using the Metronome............................................ 51 Adjusting the Tempo ............................................. 51 Tap Tempo ............................................................. 52 Reference Playing the Demos .................53 Voices.....................................55 Selecting a Voice .................................................... 55 One-touch Piano Play.............................................. 56 Layer/Left — Playing Several Sounds Simultaneously .................................................... 57 Layer — Layering Two Different Voices ................... 57 Left — Setting Separate Voices for the Left and Right Sections of the Keyboard ..................... 58 Applying Voice Effects ........................................... 58 Using the Pedals..................................................... 59 Playback of Songs ....................................................21 Playing Voices ........................................................ 25 Playing a Voice ........................................................25 Playing Two Voices Simultaneously ..........................26 Playing Different Voices with the Left and Right Hands ...................................................27 Playing Styles ......................................................... 28 Playing a style ..........................................................28 Style Sections...........................................................30 One Touch Setting...................................................32 Music Finder........................................................... 33 Using the Music Finder ............................................33 Searching the Music Finder Records.........................34 Saving and Recalling Music Finder Data ...................35 Playing and Practicing with the Songs.................. 36 Playing Along with the Clavinova.............................36 Recording ................................................................37 Mastering Your Favorite Songs.................................38 Basic Operations — Organizing Your Data ....... 39 Selecting Files and Folders..................................... 41 File/Folder-related Operations .............................. 42 Styles......................................60 Playing a style ........................................................ 60 Playing a Style’s Rhythm Channels only .................. 62 Adjusting the Volume Balance/Channel Muting ...... 62 Chord Fingerings.................................................... 63 Arranging the Style Pattern (SECTIONS: MAIN A/B/C/D, INTRO, ENDING, BREAK) ......... 65 Stopping the Style Playback While Releasing Keys (SYNC. STOP) ...................................................... 66 Selecting Intro and Ending Types (INTRO/ENDING) ... 67 Playing Fill-in patterns automatically when changing accompaniment sections — Auto Fill In................ 67 Appropriate Panel Setting for the Selected Style (ONE TOUCH SETTING) ...................................... 68 Automatically Changing One Touch Settings with the Sections — OTS Link .............................. 69 Registering the Panel Controls in One Touch Setting (ONE TOUCH SETTING) ...................................... 69 Calling Up Ideal Setups for Your Music — Music Finder.................................................... 70 Searching the Ideal Setups — Music Finder Search.. 71 Editing Records — Music Finder Record Edit ........... 72 Naming Files/Folders ...............................................42 Moving Files/Folders ................................................43 Copying Files/Folders...............................................44 Deleting Files/Folders...............................................44 Saving Files ..............................................................45 Organizing Files by Creating a New Folder ..............45 Displaying Upper Level pages ..................................45 Entering Characters and Changing Icons .................45 CVP-205/203 9 Song Playback ....................... 74 Compatible Song Types ......................................... 74 Song Playback ........................................................ 75 Playing the Internal Songs........................................75 Playing Back Songs on Disk......................................77 Other Playback-related Operations...........................77 Muting Specific Parts — Track1/Track2/Extra Tracks............................ 78 Repeat Playback of a Specific Range ..................... 78 Using the Practice Functions —Guide ................... 79 Practice Functions ....................................................79 Practicing Music with the Guide Functions...............80 Displaying Music Notation — Score (CVP-205 only)...................................... 81 Displaying the Lyrics .............................................. 84 Saving and Recalling Custom Panel Setups — Registration Memory ........ 85 Registering Panel Setups — Registration Memory...................................... 85 Saving Your Registration Memory Setups .................86 Recalling a Registration Memory Setup ................ 87 Creating Accompaniment Styles — Style Creator....................109 About Creating Accompaniment Styles............... 109 Style File Format................................................... 110 Operation ............................................................. 110 Realtime Recording — Basic ................................ 111 Step Recording..................................................... 112 Assembling an Accompaniment Style —Assembly ........................................................ 113 Edit the Created Accompaniment Style .............. 114 Change the Rhythmic Feel — Groove and Dynamics .. 114 Editing the Channel Data ...................................... 116 Making Style File Format Settings —Parameter ..... 117 Adjust the Volume Balance and Changing Voices — Mixing Console ................119 Operation ............................................................. 119 Setting the Level Balance and Voice — Volume/Voice ............................................... 120 Changing the Tone of the Voice — Filter............ 121 Changing Pitch-related Settings — Tune ............ 121 Adjusting the Effects ............................................ 122 Effect Structure ..................................................... 124 Editing Voices — Sound Creator ................... 88 Operation ............................................................... 88 SOUND CREATOR Parameters ............................... 89 Recording Your Performances and Creating Songs — Song Creator ..................... 93 About Song Recording........................................... 93 Quick Recording..................................................... 94 Multi Recording ..................................................... 95 Recording Individual Notes — Step Record .......... 97 Operation ................................................................97 Recording Melodies — Step Record (Note) ..............99 Recording Chord Changes for the Auto Accompaniment — Step Record (Chord) ............100 Select the Recording Options: Starting, Stopping, Punching In/Out — Rec Mode......... 102 Editing a Recorded Song ..................................... 103 Editing Channel-related Parameters — Channel .....103 Editing Note Events — 1 - 16.................................106 Editing Chord Events — CHD.................................107 Editing System Events — SYS/EX. (System Exclusive)..107 Inputting and Editing Lyrics ...................................108 Customizing the Event List — Filter........................108 10 CVP-205/203 Making Global and Other Important Settings — Function...........................125 Operation ............................................................. 125 Fine Tuning the Pitch/Selecting a Scale — Master Tune/Scale Tune............................... 127 Tuning the Overall Pitch — Master Tune............... 127 Selecting a Scale — Scale Tune ............................. 127 Setting Song-related Parameters — Song Settings................................................ 129 Setting Auto Accompaniment-related Parameters — Style Setting, Split Point, and Chord Fingering......................................... 130 Setting Auto Accompaniment-related Parameters — Style Setting and Split Point .......................... 130 Setting the Fingering Method — Chord Fingering .... 131 Making Settings for the Pedals and Keyboard — Controller...................................................... 131 Making Settings for the Pedals .............................. 131 Changing the Touch Sensitivity and Transpose — Keyboard/Panel ............................................. 133 Setting the Registration Sequence, Freeze, and Voice Set..................................................... 134 Specifying the Order for Calling Up Registration Memory Presets — Registration Sequence.......... 134 Maintaining Panel Settings — Freeze .................... 134 Changing the Automatically Selected Voice Settings — Voice Set ....................................................... 135 Setting Harmony and Echo.................................. 135 Showing the Clavinova Display on a TV — Video Out (CVP-205 only) ............................ 136 Setting the MIDI Parameters ............................... 137 Making Overall System Settings (Local Control, Clock, etc.) — System.................137 Transmitting MIDI Data — Transmit ......................138 Receiving MIDI Data — Receive .............................139 Setting Root Note Channels — Root ......................139 Setting Chord Channels — Chord Detect ..............139 Other Settings — Utility ...................................... 140 Making Settings for Fade In/Out, Metronome, Parameter Lock, and Tap — CONFIG 1...............140 Making Settings for the Display, Speaker System, and Voice Number Indication — CONFIG 2........141 Copying and Formatting Disks — Disk ...................142 Entering Your Name and Language Preference — Owner............................................................143 Restoring the Factory-programmed Settings of the CVP-205/203 — System Reset ............................143 Introduction Quick Guide Basic Operations - Organizing Your Data Playing the Demos Voices Using Your Clavinova with Other Devices.............. 144 Using the Headphones (PHONES jacks)..................144 Connecting the Microphone or Guitar (MIC./LINE IN jack) (CVP-205 only). ...................144 Connecting Audio & Video Devices .......................145 Using the Pedal (footswitch) or Foot Controller (AUX PEDAL jack) ...............................................146 Connecting external MIDI devices (MIDI terminals) .................................................146 Connecting to a Computer (MIDI terminals/TO HOST terminal)....................146 What’s MIDI? .........................................................148 What You Can Do With MIDI .................................150 Data Compatibility............................................... 151 Disk format ............................................................151 Sequence Format...................................................151 Voice Allocation Format .........................................152 CVP-205/205M: Keyboard Stand Assembly ................... 153 Styles Song Playback Saving and Recalling Custom Panel Setups - Registration Memory Editing Voices - Sound Creator Recording Your Performances and Creating Songs - Song Creator Creating Accompaniment Styles - Style Creator Adjust the Volume Balance and Changing Voices - Mixing Console CVP-203: Keyboard Stand Assembly ............................. 155 Making Global and Other Important Settings - Function Troubleshooting.................. 157 Using Your Clavinova with Other Devices Specifications ...................... 159 Appendix Index ................................... 161 CVP-205/203 11 Application Index Use this index to find reference pages that may be helpful for your particular application and situation. Listening Listening to the internal songs ................................................................................................................ page 75 Listening to disk songs ....................................................................... “Playing Back Songs on Disk” on page 77 Listening to demo songs......................................................................................................................... page 53 Listening to the demo of the selected voices .......................................................................................... page 55 Listening to songs with the special voices of the Clavinova .................................................................. page 120 Playing Calling up the piano setting ................................................................................................................... page 56 Using the three performance control pedals........................................................................................... page 59 Playing an accompaniment that matches pitch..................................................“Transpose Assign” on page 133 Combining two voices ...................................................... “Layer — Layering Two Different Voices” on page 57 Playing separate voices with the right and left hands ...........................“Left — Setting Separate Voices for the Left and Right Sections of the Keyboard” on page 58 Changing the sound Enhancing the sound with reverb and other effects .....................................“Applying Voice Effects” on page 58 .................................................................................................................“Adjusting the Effects” on page 122 Adjusting the Level Balance ................................................................................................................. page 120 Combining two voices ...................................................... “Layer — Layering Two Different Voices” on page 57 Playing separate voices with the right and left hands ...........................“Left — Setting Separate Voices for the Left and Right Sections of the Keyboard” on page 58 Creating voices ...................................................................................................................................... page 88 Playing the auto accompaniment Playing the accompaniment automatically ............................................................................................. page 60 Calling up ideal panel settings for your music ........................................................................................ page 70 Practicing Muting the right- or left-hand part .......................................................................................................... page 80 Practicing with an accurate and steady tempo............................................. “Using the Metronome” on page 51 Recording Recording your performance...........................................................................................................pages 94, 95 Creating a song by entering notes .......................................................................................................... page 97 Creating your original settings Creating voices ...................................................................................................................................... page 88 Creating accompaniment styles............................................................................................................ page 109 12 CVP-205/203 Using a microphone (CVP-205 only) Connecting the microphone.............. ”Connecting the Microphone or Guitar (MIC./LINE IN jack)” on page 144 Settings Registering Panel Setups......................................................................................................................... page 85 Tuning the pitch/Selecting a scale ........................................................................................................ page 127 Making detailed settings for playing back songs ................................................................................... page 125 Making detailed settings for the auto accompaniment.......................................................................... page 130 Making settings for the pedals ........... “Making Settings for the Pedals and Keyboard — Controller” on page 131 Making detailed settings for the keyboard voices ................................................................................. page 133 Showing the display on a TV (CVP-205 only) .....................................“Showing the Clavinova Display on a TV — Video Out (CVP-205 only)” on page 136 Making detailed settings for MIDI ........................................................................................................ page 137 Connecting the Clavinova to other devices Basic information on MIDI..................................................................................... “What’s MIDI?” on page 148 Recording your performance................ ”Playing the sounds of the Clavinova through an external audio system, and recording the sounds to an external recorder (AUX OUT jacks)” on page 145 Raising the volume .............................. ”Playing the sounds of the Clavinova through an external audio system, and recording the sounds to an external recorder (AUX OUT jacks)” on page 145 Outputting another instrument’s sound from the Clavinova ............ ”Outputting the sound of an external device through the built in speakers of the Clavinova (AUX IN jacks)” on page 145 Connecting a computer........... .”Connecting to a Computer (MIDI terminals/TO HOST terminals)” on page 146 Assembling Assembling and disassembling the Clavinova............“CVP-205/205M: Keyboard Stand Assembly” on page 153 “CVP-203: Keyboard Stand Assembly” on page 155 Quick solution Basic functions of the Clavinova and how you can best use it .........................................................pages 12, 14 Resetting the Clavinova to the default setting .................... “Restoring the Factory-programmed Settings of the CVP-205/203 — System Reset” on page 143 Displaying the Messages ......................................................................“About the Display Messages” on page 8 Troubleshooting ................................................................................................................................... page 157 CVP-205/203 13 What can you do with the Clavinova? SONG GUIDE DEMO Playback previously recorded songs (page 21, 36, 74) Learn and practice with the Guide functions (page 38, 79) Explore the Demos (page 20, 53) Enjoy a wide variety of preset songs as well as songs on commercially available disks. Play back the preset songs or the appropriate disk software, and let the display and guide lamps show you when and where to play the proper notes. It’s never been easier or more fun to learn new music! These not only showcase the stunning voices and styles of the instrument, they introduce you to the various functions and features — and give you hands-on experience using the Clavinova! METRONOME POWER ON OFF START STOP SONG EXTRA TRACKS (STYLE) TRACK 2 (L) TRACK 1 (R) MENU DEMO REC TOP START / STOP REW FF REPEAT GUIDE MASTER VOLUME TEMPO TRANSPOSE MAX RESET RESET STYLE AUTO FILLIN BREAK INTRO ENDING / rit. MAIN A FUNCTION B DIGITAL STUDIO TAP TEMPO ACMP A SYNC.START NEW SONG FADE IN / OUT MIN HELP B C D OTS LINK SYNC.STOP SYNC.START START / STOP C SOUND CREATOR D DIGITAL RECORDING E MIXING CONSOLE BALANCE PART CHANNEL ON / OFF PART DIRECT ACCESS 14 1 STYLE DIGITAL RECORDING Back up your performance with Auto Accompaniment (page 28, 60) Record your performances (page 93, 109) Playing a chord with your left hand automatically plays the auto accompaniment backing. Select an accompaniment style — such as pop, jazz, Latin, etc. — and let the Clavinova be your backing band! With the powerful and easy-to-use song recording features, you can record your own keyboard performances, and create your own complete, fully orchestrated compositions — which you can then save to the USER drive or a floppy disk for future recall. CVP-205/203 2 3 4 LCD MUSIC FINDER VOICE The large LCD (together with the various panel buttons) provides comprehensive and easyto-understand control of the Clavinova’s operations. Call up the perfect accompaniment style (page 33, 70) Enjoy a huge variety of realistic voices (page 25, 55) If you know what song you want to play, but you don’t know which style or voice would be right for it, let the Music Finder help you. Just select the song title, and the Clavinova automatically calls up the most appropriate style and voice. The Clavinova features a wealth of exceptionally authentic and dynamic voices (more than 800) — including piano, strings, woodwinds, and more! LCD CONTRAST BACK VOICE EFFECT REVERB DSP VARIATION HARMONY / ECHO MONO LEFT HOLD E.PIANO ORGAN & ACCORDION PERCUSSION GUITAR BASS WOODWIND STRINGS CHOIR & PAD SYNTH. XG NEXT VOICE PIANO & HARPSI. F VOICE PART ON / OFF G LAYER H LEFT BRASS USER ENTER ONE TOUCH SETTING MUSIC FINDER I 1 2 3 4 J DATA ENTRY 5 6 7 8 REGISTRATION MEMORY PIANO 1 FREEZE EXIT 2 3 4 5 6 7 8 MEMORY TO HOST terminal Make music with a computer — quickly and easily (page 146) Dive in and take advantage of the wide world of computer music software. Connections and setup are exceptionally easy, and you can play back your computer recorded parts with different instrument sounds — all from a single Clavinova! PIANO Set up the piano — instantly (page 56) You can call up all the optimum piano settings for the Clavinova with just a single button press — then play the extraordinarily realistic grand piano voice. CVP-205 IN OUT THRU L L+R PC-2 MIDI MIDI R L L+R R (LEVEL FIXED) L R PC-1 Mac HOST SELECT TO HOST AUX PEDAL VIDEO OUT AUX IN AUX OUT CVP-205/203 15 Setting Up the Clavinova ■ To lower the music stand: Key cover ■ To open the key cover: Lift the cover slightly, then push and slide it open. ■ To close the key cover: Slide the cover toward you and gently lower the cover over the keys. the music stand toward yourself as far as it will 1 Pull go. the two metal supports until they are flat 2 Raise against the rear surface of the stand. lower the music stand backward until it is all 3 Gently the way down. CAUTION Be careful to avoid catching your fingers when opening or closing the cover. CAUTION Do not try to use the music stand in a half-raised position. Also, when lowering the stand, let the stand all the way down before releasing it. CAUTION Hold the cover with both hands when opening or closing it. Do not release it until it is fully opened or closed. Be careful to avoid catching fingers (yours or others, especially children’s) between the cover and the unit. CAUTION Do not place objects such as a piece of metal or paper on top of the key cover. Small objects placed on the key cover may fall inside the unit when the cover is opened and may be nearly impossible to remove. This could cause electric shock, short circuit, fire or other serious damage to the instrument. Sheet Music Braces (CVP-205 only) These braces are for holding the pages of music books in place. ■ To open Music Stand ■ To raise the music stand: the stand up and toward yourself as far as it will 1 Pull go. down the two metal supports at the left and the 2 Flip right on the rear of the music stand. the music stand so that it rests on the metal 3 Lower supports. 16 CVP-205/203 ■ To close Turning the Power On and Off Adjusting the display contrast If the LCD is difficult to read, adjust the contrast with the [LCD CONTRAST] knob at the right of the LCD. Connect the power cord. LCD CONTRAST the plugs at the ends of the cord, one into the 1 Insert AC INLET on the Clavinova, and the other into a standard AC outlet. In some areas, a plug adapter may be provided to match the pin configuration of the AC wall outlets in your area. Setting the volume CVP-203 CVP-205 Use the [MASTER VOLUME] dial to adjust the volume to an appropriate level. MASTER VOLUME FADE IN / OUT MAX MIN CAUTION Do not use the Clavinova at a high volume level for a long period of time, or your hearing may be damaged. (The shape of plug differs depending on locale.) Using headphones the [POWER] switch. 2 Press → The main display appears in the LCD display. The drive lamp below the lower right end of the keyboard also lights. Connect a pair of headphones to one of the [PHONES] jacks. Two [PHONES] jacks are provided. Two sets of standard stereo headphones can be plugged in. (If you are using only one pair of headphones, you can plug them into either of these jacks.) POWER ON OFF The drive lamp lights. F B G H D I E J BALANCE CVP-205 INPUT VOLUME CHANNEL ON / OFF MIN PART MIC. LINE IN MIC. LINE CVP-203 PHONES MAX PHONES A C When you’re ready to turn off the power, press the [POWER] switch again. → Both the display and the drive lamp below the right end of the keyboard will turn off. CVP-205/203 17 Panel Controls and Terminals CVP-205 IN CVP-203 OUT THRU L L+R PC-2 MIDI R L L+R MIDI (LEVEL FIXED) L R R PC-1 Mac Mac PC-1 AUX PEDAL MIDI HOST SELECT 69 TO HOST AUX PEDAL VIDEO OUT AUX IN METRONOME POWER OFF 75 R L (LEVEL FIXED) THRU 76 72 71 70 OUT 69 2 EXTRA TRACKS (STYLE) TRACK 2 (L) TRACK 1 (R) 5 6 7 76 REC TOP START / STOP REW FF REPEAT GUIDE 8 9 10 11 12 13 14 SYNC.START NEW SONG 31 32 33 FADE IN / OUT TEMPO 3 TAP TEMPO 4 15 RESET STYLE AUTO FILLIN BREAK INTRO 16 A B RESET ENDING / rit. MAIN 19 C HELP 20 75 74 B 17 SYNC.STOP SYNC.START START / STOP 34 35 36 C SOUND CREATOR D DIGITAL RECORDING E MIXING CONSOLE D 38 BALANCE PART CHANNEL ON / OFF 21 L L+R AUX IN A FUNCTION OTS LINK 18 R 37 DEMO DIGITAL STUDIO TRANSPOSE MAX ACMP L L+R MENU MASTER VOLUME MIN R AUX OUT IN SONG START STOP 1 MIDI PC-2 HOST SELECT AUX OUT 70 71 72 73 74 ON TO HOST 22 23 24 25 26 27 28 29 30 39 PART 40 DIRECT ACCESS 45 1 2 3 4 65 66 67 68 INPUT VOLUME MIC. LINE IN MIC. LINE PHONES MAX PHONES MIN CVP-205 68 CVP-203 POWER 1 [ON / OFF] button (POWER)................................................ P. 17 METRONOME 2 [START / STOP] button (METRONOME) ............................. P. 51 MASTER VOLUME 3 4 [MASTER VOLUME] dial...................................................... P. 17 [FADE IN / OUT] button........................................................ P. 66 SONG 5 6 7 8 9 10 11 12 13 14 [EXTRA TRACKS (STYLE)] button ...................................... P. 78 [TRACK 2 (L)] button............................................................ P. 78 [TRACK 1 (R)] button ........................................................... P. 78 [REC] button ........................................................................ P. 93 [TOP] button......................................................................... P. 77 [START / STOP] button (SONG) .......................................... P. 75 [REW] button........................................................................ P. 77 [FF] button............................................................................ P. 77 [REPEAT] button .................................................................. P. 78 [GUIDE] button..................................................................... P. 79 TEMPO 15 [E] [F] buttons (TEMPO)............................................... P. 51 16 [TAP TEMPO] button ............................................................ P. 52 TRANSPOSE 17 [E] [F] buttons (TRANSPOSE) ................................... P. 133 STYLE 18 19 20 21 22 23 24 18 [ACMP] button...................................................................... P. 61 [AUTO FILLIN] button........................................................... P. 67 [OTS LINK] button................................................................ P. 69 [BREAK] button.................................................................... P. 65 [INTRO] button ............................................................... P. 31, 67 MAIN [A] button.................................................................... P. 65 MAIN [B] button.................................................................... P. 65 CVP-205/203 25 26 27 28 29 30 MAIN [C] button ................................................................... P. 65 MAIN [D] button ................................................................... P. 65 [ENDING / rit.] button..................................................... P. 31, 67 [SYNC.STOP] button ........................................................... P. 66 [SYNC.START] button.......................................................... P. 61 [START / STOP] button (STYLE) ......................................... P. 61 MENU 31 [DEMO] button ..................................................................... P. 53 32 [HELP] button ...................................................................... P. 50 33 [FUNCTION] button ........................................................... P. 125 DIGITAL STUDIO 34 [SOUND CREATOR] button ................................................. P. 88 35 [DIGITAL RECORDING] button ................................... P. 93, 109 36 [MIXING CONSOLE] button............................................... P. 119 DISPLAY CONTROL 37 38 39 40 41 42 43 44 45 46 47 48 49 [A] - [J] buttons..................................................................... P. 41 [BALANCE] button ............................................................... P. 62 [CHANNEL ON / OFF] button ........................................ P. 62, 77 [DIRECT ACCESS] button................................................... P. 48 [BACK] button ................................................................ P. 41, 47 [NEXT] button ................................................................ P. 41, 47 VOICE PART ON / OFF [LAYER] button.............................. P. 57 VOICE PART ON / OFF [LEFT] button ................................ P. 57 [1▲▼] - [8▲▼] buttons ................................................. P. 39 - 46 [LCD CONTRAST] knob ...................................................... P. 17 [ENTER] button.................................................................... P. 47 [DATA ENTRY] dial............................................................... P. 47 [EXIT] button ........................................................................ P. 41 VOICE EFFECT 50 [REVERB] button ................................................................. P. 58 51 [DSP] button......................................................................... P. 58 64 77 63 78 79 46 VOICE EFFECT LCD CONTRAST 41 BACK NEXT 42 REVERB DSP 50 VARIATION 51 52 HARMONY / ECHO 53 MONO LEFT HOLD 54 55 VOICE 37 PIANO & HARPSI. F E.PIANO ORGAN & ACCORDION PERCUSSION GUITAR BASS WOODWIND STRINGS CHOIR & PAD SYNTH. XG VOICE PART ON / OFF G LAYER H LEFT 43 44 47 56 BRASS USER ENTER ONE TOUCH SETTING MUSIC FINDER I 57 58 1 2 3 4 J DATA ENTRY 48 REGISTRATION MEMORY PIANO 59 60 FREEZE 61 1 2 3 4 5 6 7 8 62 MEMORY 49 5 52 53 54 55 6 7 8 EXIT [VARIATION] button ............................................................. P. 58 [HARMONY / ECHO] button ................................................ P. 59 [MONO] button ..................................................................... P. 59 [LEFT HOLD] button ............................................................ P. 59 VOICE 56 VOICE buttons ..................................................................... P. 55 MUSIC FINDER 57 [MUSIC FINDER] button ...................................................... P. 70 ONE TOUCH SETTING 58 [1] - [4] buttons (ONE TOUCH SETTING)............................ P. 68 PIANO Setting 59 [PIANO] button..................................................................... P. 56 REGISTRATION MEMORY 60 [FREEZE] button.................................................................. P. 87 61 [1] – [8] buttons (REGISTRATION MEMORY) ..................... P. 85 62 [MEMORY] button ................................................................ P. 85 63 Floppy disk drive (3.5”)........................................................... P. 6 64 Keyboard guide lamps ......................................................... P. 79 Microphone and Headphone Connectors 65 66 67 68 [INPUT VOLUME] knob...................................................... P. 144 [MIC. LINE IN] jack............................................................. P. 144 [MIC. LINE] switch.............................................................. P. 144 [PHONES] jacks................................................................. P. 144 Connectors 69 70 71 72 73 74 75 76 MIDI [THRU] [OUT] [IN] terminals...................................... P. 146 [HOST SELECT] switch ..................................................... P. 146 [TO HOST] terminal ........................................................... P. 147 [AUX PEDAL] jack.............................................................. P. 146 [VIDEO OUT] jack .............................................................. P. 145 AUX IN [L / L+R] [R] jacks.................................................. P. 145 AUX OUT [L / L+R] [R] jacks.............................................. P. 145 AUX OUT (LEVEL FIXED) [L] [R] jacks ............................. P. 145 Pedals 77 Left pedal ............................................................................. P. 59 78 Sostenuto pedal ................................................................... P. 59 79 Damper pedal ...................................................................... P. 59 The Panel Logos The logos printed on the Clavinova panel indicate standards/ formats it supports and special features it includes. GM System Level 1 “GM System Level 1” is an addition to the MIDI standard which guarantees that any data conforming to the standard will play accurately on any GM-compatible tone generator or synthesizer from any manufacturer. XG Format XG is a new Yamaha MIDI specification which significantly expands and improves on the “GM System Level 1” standard with greater voice handling capacity, expressive control, and effect capability while retaining full compatibility with GM. By using the Clavinova’s XG voices, it is possible to record XG-compatible song files. XF Format The Yamaha XF format enhances the SMF (Standard MIDI File) standard with greater functionality and open-ended expandability for the future. The Clavinova is capable of displaying lyrics when an XF file containing lyric data is played. (SMF is the most common format used for MIDI sequence files. The Clavinova is compatible with SMF Formats 0 and 1, and records “song” data using SMF Format 0.) Disk Orchestra Collection The DOC voice allocation format provides data playback compatibility with a wide range of Yamaha instruments and MIDI devices. Style File Format The Style File Format (SFF) is Yamaha’s original style file format, which uses a unique conversion system to provide high-quality automatic accompaniment based on a wide range of chord types. The Clavinova uses the SFF internally, reads optional SFF style disks, and creates SFF styles using the Style Creator feature. CVP-205/203 19 Quick Guide . . . . . . . . . . . . . . . . . . . . . . . . . Playing the Demos Reference on page 53 The Clavinova features an extensive variety of Demo songs, that showcase its rich, authentic voices and its dynamic rhythms and styles. Demo button What’s more, there’s a special selection of Demo functions. These take you through a hands-on journey of all the important features and functions of the instrument — letting you see firsthand how to effectively use the Clavinova in your own music. 1 2 Pressing the [DEMO] button automatically plays back the Demo songs at random. Press the [BACK]/[NEXT] button to select the Demo categories. BACK NEXT MENU DEMO HELP FUNCTION Voice Demos showcase the voices of the CVP-205/203. Style Demos introduce you to the rhythms and accompaniment styles of the CVP205/203 (page 53). For this example, FUNCTION is selected. Function Demos demonstrate many of the different functions on the CVP-205/203. 3 Press any of the [A] to [J] buttons or [8▼] (AUTO) button (FUNCTION page only) to select the Demo songs. For this example, press the [8▼] (AUTO) button. All of the function demos are played back in sequence. VOICE PART A F B G LAYER C H LEFT D I E J ON / OFF For details about the Demos, refer to page 53. 1 2 3 4 5 6 7 8 Press the [EXIT] button to exit from the demo mode and return to the MAIN display when you’ve finished playing the demo songs. When you’re done with the Demos, you can get to know your Clavinova even better with these functions: • Preset Song (Song Book) playback (CVP-205) (page 21) • Disk Song Playback (CVP-203) (page 21) • Short demo playback of the selected voice (in the Voice Open display; page 26). 20 Quick Guide Song Playback Song Playback Reference on page 74 Here’s where all of the amazing voices, effects, rhythms, styles and other sophisticated features of the Clavinova come together — in songs! As you heard in the Demos, the Clavinova contains many built-in recordings. But there’s more. On the CVP-203, check out the included disk; on the CVP-205 or 203, call up the Song Open (PRESET) display. And there’s an even greater wealth of song material you can enjoy with your Clavinova — in commercially available software. Make sure that the Language setting for the instrument (page 143) is the same as that of the file name of the song that you are playing back. Song related buttons BALANCE and CHANNEL buttons Floppy disk drive The following songs are compatible for playback on the CVP-205/203. Refer to pages 74, 151 for more details on the logos. Disks bearing this logo contain song data for voices defined in the GM standard. Disks bearing this logo contain song data using the XG format, an extension of the GM standard that provides a wider variety of voices and more comprehensive sonic control. Disks bearing this logo contain song data for voices defined in Yamaha’s DOC format. Songs containing a large amount of data may not be able to be read properly by the instrument, and as such you may not be able to select them. The maximum capacity is about 200– 300KB, however this may differ depending on the data contents of each song. Playback of Songs 1 If you want to play back a disk song, insert an appropriate disk containing song data into the disk drive. CAUTION • Make sure to read the section “Using the Floppy Disk Drive (FDD) and Floppy Disks” on page 6. Quick Guide 21 Song Playback 2 Press the [A] button to call up the Song Open display. If the MAIN screen is not displayed, press the [DIRECT ACCESS] button followed by the [EXIT] button. From the MAIN display (the display shown when the power is turned on), you can select songs, voices, accompaniment styles, etc. PRESET FLOPPY DISK Press the [BACK]/[NEXT] button to select the drive. In the example display of the CVP-205 at left, the PRESET page is selected. At right is a display from the CVP-203, with FLOPPY DISK selected. 3 PRESET only Press the [A] button to select the preset songs (Song Book; CVP-205 only) folder. A B C D E 22 Quick Guide Song Playback 4 5 Press one of the [A] to [J] buttons to select a song file. Press the SONG [START/STOP] button to start playback. REC TOP • To rewind or fast forward to the playback point of the song, press the [REW] or [FF] button. • With song data software (Standard MIDI format 0) that includes lyrics, you can view the lyrics on the display during playback. You can also view the score (CVP-205 only). See pages 81 and 84 for details. SYNC.START NEW SONG 6 START / STOP While the song is playing, try using the Mute function to turn certain instrument channels off or on — letting you craft dynamic arrangements on the fly! 1) Press the [CHANNEL ON/OFF] button. 2) Press the [1 - 8▲▼] button corresponding to the channel you wish to turn on or off. CHANNEL ON / OFF PART 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 If the STYLE tab is selected, press this button again. Quick Guide 23 Song Playback 7 Finally, take the producer’s seat and try your hand at mixing. These Balance controls let you adjust the levels of the individual parts — the song, the style, your singing (CVP-205 only), and your playing. 1) Press the [BALANCE] button. 2) Press the [1 - 8▲▼] button corresponding to the part of which the volume you wish to adjust. You can call up a full set of mixing controls by pressing the [MIXING CONSOLE] button (page 119). BALANCE 1 8 3 4 5 6 7 8 Press the SONG [START/STOP] button to stop playback. REC NEW SONG 24 2 Quick Guide TOP START / STOP SYNC.START • The [FADE IN/OUT] button (page 66) can be used to produce smooth fadeins and fade-outs when starting and stopping the song, as well as the accompaniment. Playing Voices Playing Voices Reference on page 55 The Clavinova features a stunning variety of over 800 dynamic, rich and realistic voices. Try playing some of these voices now and hear what they can do for your music. Here, you’ll learn how to select individual voices, combine two voices in a layer, and split two voices between your left and right hands. Voice related buttons Playing a Voice 1 Press the [F] button to call up the menu for selecting the MAIN voice. If the MAIN screen is not displayed, press the [DIRECT ACCESS] button followed by the [EXIT] button. F The voice you’re selecting here belongs to the MAIN part, and is called the MAIN voice. (See page 57 for more information.) VOICE PART ON / OFF G LAYER H LEFT I J You’ll want to hear the MAIN voice all by itself — so make sure that the LAYER and LEFT parts are turned off. 2 Select a voice group. VOICE PIANO & HARPSI. BRASS E.PIANO ORGAN & ACCORDION PERCUSSION GUITAR BASS WOODWIND STRINGS CHOIR & PAD SYNTH. XG USER For this example, STRINGS is selected. Press the [BACK]/[NEXT] button to select the memory location of the voice. For this example, PRESET is selected. Quick Guide 25 Playing Voices 3 Select a voice. You can instantly jump back to the Main display by “double-clicking” on one of the [A] - [J] buttons. A For this example, ”Orchestra” is selected. B C D E Press the [8▲] button to start the Demo for the selected voice. To stop the Demo, press this button again. There’s more to the Demo features than just voices, though–for more information, see page 53. Press the corresponding buttons to select the other pages — and discover even more voices. 4 Play the voices. Naturally, you can play the voice yourself from the keyboard, but you can also have the Clavinova demonstrate the voice for you. Simply press the [8▲] button from the display above, and a Demo of the voice plays automatically. Playing Two Voices Simultaneously 1 2 3 Press the VOICE PART ON/OFF [LAYER] button to turn the LAYER part on. VOICE PART ON / OFF Press the [G] button to select the LAYER part. G LAYER H LEFT Select a voice group. Here, we’ll select a lush pad to fill out the sound. Call up the “CHOIR & PAD” group. VOICE PIANO & HARPSI. BRASS 4 5 E.PIANO ORGAN & ACCORDION PERCUSSION GUITAR BASS WOODWIND STRINGS CHOIR & PAD SYNTH. XG USER Select a voice. For example, select “Hah Choir.” Play the voices. Now, you can play two different voices together in a rich sounding layer — the MAIN voice you selected in the previous section, plus the new LAYER voice you’ve selected here. And that’s just the beginning. Check out these other voice-related features: • Instant setup of the Clavinova for piano play — with the press of a single button (page 56). • Create your own original voices — quickly and easily — by changing the settings of existing voices (page 88). • Set up your favorite panel settings — including voices, styles, and more — and call them up whenever you need them (page 85). 26 Quick Guide Playing Voices Playing Different Voices with the Left and Right Hands 1 2 3 Press the VOICE PART ON/OFF [LEFT] button to turn the LEFT part on. LAYER LEFT Press the [H] button to select the LEFT part. Select a voice group. Here, we’ll select the “STRINGS” group — so that you can play rich, orchestral chords with your left hand. VOICE PIANO & HARPSI. BRASS 4 5 6 E.PIANO ORGAN & ACCORDION PERCUSSION GUITAR BASS WOODWIND STRINGS CHOIR & PAD SYNTH. XG USER Select a voice, then press the [EXIT] button to return to the MAIN display. For example, select “Symphon. Str.” Press the [I] button to call up the SPLIT POINT display. From here, you can set the particular key on the keyboard that separates the two voices — called the Split Point. To do this, simultaneously hold down the [F] or [G] button and press the desired key on the keyboard. (For more information, see page 130.) F F G G H H I I J J Play the voices. The notes you play with your left hand sound one voice, while the notes you play with your right sound a different voice (or voices). Split Point MAIN/LAYER LEFT MAIN and LAYER voices are meant to be played with the right hand. The LEFT voice is played with the left hand. 7 Press the [EXIT] button to return to the MAIN display. EXIT Quick Guide 27 Playing Styles Playing Styles The Clavinova has a huge variety of musical “styles” that you can call upon to back up your own performance. They give you anything from a simple, yet effective piano backing or percussion accompaniment to a full band or orchestra. Reference on page 60 Style related buttons Playing a style 1 Press the [D] button to call up the style group. If the MAIN screen is not displayed, press the [DIRECT ACCESS] button followed by the [EXIT] button. Press the [BACK]/[NEXT] button to select the memory location of the style. For this example, PRESET is selected. A B C D E 2 Select a style group and a style. A A B B C C D D E E For this example, Dance is selected. 28 Quick Guide For this example, EuroTrance is selected. Playing Styles 3 Turn ACMP on. The specified left-hand section of the keyboard becomes the “Auto Accompaniment” section, and chords played in this section are automatically detected and used as a basis for fully automatic accompaniment with the selected style. Split Point ACMP Auto Accompaniment section 4 • The point on the keyboard that separates the auto accompaniment section and the right-hand section of the keyboard is called the “split point.” Refer to page 130 for instructions on setting the split point. Turn SYNC.START on. SYNC.START 5 As soon as you play a chord with your left hand, the style starts. For this example, play a C major chord (as shown below). Split Point Auto Accompaniment section 6 7 8 Change the tempo by using the TEMPO[ ] [ ] buttons if necessary. Simultaneously press the TEMPO [ ] [ ] buttons to return the tempo to its original setting. Press the [EXIT] button to leave the TEMPO display. The Tempo can also be adjusted by using the [TAP TEMPO] button (page 52). Try playing other chords with your left hand. For information on how to enter chords, see “Chord Fingerings” on page 63. Press the STYLE [START/STOP] button to stop the style. And there’s much more. Check out these other style-related features: • Easily create your own original styles (page 109). • Set up your favorite panel settings — including styles, voices, and more — and call them up whenever you need them (page 85). Quick Guide 29 Playing Styles Embellish and enhance your melodies — with the automatic Harmony and Echo effects This powerful performance feature lets you automatically add harmony notes to the melodies you play with your right hand — based on the chords you play with your left. Tremolo, Echo, and other effects are available, too. 1 Turn HARMONY/ECHO on. VOICE EFFECT REVERB DSP VARIATION HARMONY / ECHO MONO LEFT HOLD 2 Turn ACMP on (page 28). 3 Play a chord with your left hand and play some notes in the right-hand range of the keyboard. The CVP-205/203 has various Harmony/Echo types (page 135). The Harmony/Echo type may change according to the selected MAIN voice. For details about Harmony/ Echo types, refer to the separate Data List. • Harmony/Echo is just one of the many Voice Effects you can use. Try out some of the other effects and see how they can enhance your performance (page 58). Style Sections Each style in the auto accompaniment is made up of “sections.” Since each section is a rhythmic variation of the basic style, you can use them to add spice to your performance and mix up the beats — while you’re playing. Intros, Endings, Main patterns, and Breaks — they’re all here, giving you the dynamic elements you need to create professionalsounding arrangements. INTRO MAIN BREAK ENDING 1-4 5 This is used for the beginning of the song. When the intro finishes playing, accompaniment shifts to the main section. This is used for playing the main part of the song. It plays an accompaniment pattern of several measures, and repeats indefinitely until another section’s button is pressed. This lets you add dynamic variations and breaks in the rhythm of the accompaniment, to make your performance sound even more professional. This is used for the ending of the song. When the ending is finished, the auto accompaniment stops automatically. Use the same operations as in “Playing a style” on pages 28 and 29. Press the [INTRO] button. BREAK INTRO 6 ENDING / rit. MAIN A B C D C D As soon as you play a chord with your left hand, the Intro starts. For this example, play a C major chord (as shown below). Split Point Auto Accompaniment section When the playback of the intro is finished, it automatically leads into main section. 7 30 Press any of the MAIN [A] to [D] buttons or [BREAK] button as desired. (See the Accompaniment Structure on the next page.) Quick Guide BREAK INTRO or ENDING / rit. MAIN A B Playing Styles 8 9 Press the [AUTO FILL IN] button to add a fill-in, if necessary. Fill-in patterns play automatically between each change in the Main sections. Press the [ENDING] button. This switches to the ending section. When the ending is finished, the style automatically stops. AUTO FILLIN BREAK INTRO ENDING / rit. MAIN A B C D ■ Accompaniment Structure INTRO (page (page 67) xx) INTRO A INTRO B INTRO C INTRO D (max. four patterns) MAIN VARIATION via BREAK MAIN VARIATION B via BREAK MAIN VARIATION A MAIN VARIATION C via BREAK MAIN VARIATION D via BREAK Press the [ENDING] button. ENDING ENDING(page (page xx) 67) ENDING A ENDING B ENDING C ENDING D You can have the ending gradually slow down (ritardando) by pressing the [ENDING] button again while the ending is playing back. (max. four patterns) • An Intro doesn’t necessarily have to be at the beginning! If you want, you can play an Intro section in the middle of your performance by simply pressing the [INTRO] button at the desired point. • Watch your timing with the Break sections. If you press a [BREAK] button too close to the end of the measure (i.e., after the final eighth note), the Break section starts playing from the next measure. This also applies to the Auto Fill-in. • Mix up your intros and use any of the other sections to start the style, if you want. • If you want to come back into the style right away after an Ending, simply press the [INTRO] button while the Ending section is playing. • If you press the [BREAK] button while the ending is playing, the break will immediately start playing, continuing with the main section. Quick Guide 31 Playing Styles Other Controls FADE IN/OUT FADE IN / OUT TAP TEMPO TAP TEMPO SYNC.STOP SYNC.STOP The [FADE IN/OUT] button can be used to produce smooth fade-ins and fade-outs (page 66)when starting and stopping the style. The style can be started at any tempo you desire by “tapping” out the tempo with the [TAP/TEMPO] button. For details, see page 52. When Synchro Stop is on, you can stop and start the style anytime you want by simply releasing or playing the keys (in the Auto Accompaniment section of the keyboard). This is a great way to add dramatic breaks and accents to your performance. For details, see page 66. ONE TOUCH SETTING buttons One Touch Setting One Touch Setting is a powerful and convenient feature that automatically calls up the most appropriate panel settings (voice number, etc.) for the currently selected style, with the touch of a single button. This is a wonderful way to instantly reconfigure all the settings on the Clavinova to match the style you want to play. 1 2 3 4 5 Select a style (page 28). Press one of the [ONE TOUCH SETTING] buttons. Not only does this instantly call up all the settings (voices, effects, etc.) that match the current style (see page 68) — it also automatically turns on ACMP and SYNC. START, so that you can immediately start playing the style. ONE TOUCH SETTING 1 2 3 4 As soon as you play a chord with your left hand, the auto accompaniment starts. Split Point Play melodies with your right hand and play various chords with your left hand. Auto Accompaniment section Try out other One Touch Setting setups. You can also create your own One Touch Setting setups. For details, refer to page 69. ONE TOUCH SETTING 1 2 3 4 • Here’s another way to further automate musical changes and spice up your performance: Use the convenient OTS (One Touch Setting) Link function to automatically change One Touch Settings when you select a different Main section (page 69). 32 Quick Guide Music Finder Music Finder Reference on page 70 MUSIC FINDER button If you want to play in a certain song but don’t know which style and voice settings would be appropriate, the convenient Music Finder can help you out. Simply select the song name from the Music Finder and the CVP-205/203 automatically makes all appropriate panel settings to let you play in that music style! Using the Music Finder 1 Press the [MUSIC FINDER] button. MUSIC FINDER 2 Select a record. Press the [BACK]/[NEXT] button to select the desired page of records. For this example, ALL is selected. Select the desired record. For this example, press the [1 - 3▲▼] button to select a record by song title. 3 Play along with the style playback. Split Point You can also have the voice and other important settings change automatically with the style changes. To do this, turn on OTS LINK (page 69) and set the OTS LINK TIMING (page 130) to “REAL.” Auto Accompaniment section Press the [EXIT] button to return to the MAIN display. Quick Guide 33 Music Finder Searching the Music Finder Records The Music Finder is also equipped with a convenient search function that lets you enter a song title or keyword — and instantly call up all the records that match your search criteria. 1 Press the [MUSIC FINDER] button. MUSIC FINDER 2 Press the [I] button to call up the MUSIC FINDER SEARCH 1 display. The results of Search 1 and 2 appear in the correspondingly numbered SEARCH 1/ 2 displays. Refer to page 46 for instructions on entering characters. 4 For this example, press the [A] button to call up the display for inputting the song title. 3 For this example, ANY is selected. 5 34 Enter the song title, then press the [8▲] (OK) button. Quick Guide For this example, ALL is selected. 6 Press the [F], [G] and [H] to clear the previous conditions, if necessary. Press the [8▲] (START SEARCH) button. The search function calls up all records that contain the entered word or words. Music Finder 7 Select a record (see step #2 on page 33) and play along with the style playback. Split Point Auto Accompaniment section Press the [EXIT] button to return to the MAIN display. You can also create your own Music Finder setups and save them to floppy disk (pages 39 and 45). In this way, you can expand your Music Finder collection by exchanging them with other Clavinova users. Saving and Recalling Music Finder Data To save your Music Finder data, call up the MUSIC FINDER Open/Save window from the SYSTEM RESET page (page 143) of the UTILITY display, and follow the same procedure as that in the Open/Save window for Voice (page 39, 45). To recall the saved data, execute the appropriate operation from the MUSIC FINDER’s Open/Save window. Records can be replaced or added (page 72). Music Finder data is compatible for both the CVP-205 and the CVP-203. In the instructions above, all Music Finder data is handled together. Besides this, when you save or load style files, the Music Finder data that uses the relevant style file(s) is stored or added automatically. When you copy or move a style file on a floppy disk to the USER drive (page 43, 44), the record which was recorded when storing the relevant style is automatically added to the CVP-205/203. • In the example above, you specified a song title, but you can also look for relevant records by keyword or music genre — for example, Latin, 8-beat, etc. (page 71). Quick Guide 35 Playing and Practicing with the Songs Playing and Practicing with the Songs Reference on page 74 Song related buttons Playing Along with the Clavinova In this section, try using the Clavinova’s song playback features to cancel or mute the right-hand melody while you play the part yourself. It’s like having a very talented and versatile playing partner accompany you while you perform. If you haven't yet mastered the melody part, take a look at the section “Mastering Your Favorite Songs” on page 38, and practice it a while. 1-4 5 Use the same operations as in “Song Playback” on pages 21 - 23. Press the [TRACK 1] button to cancel the right hand melody part. TRACK 1 (R) 6 To cancel the left hand part, press the [TRACK 2] button If you want to have the notation displayed as you play (CVP-205 only), press the [C] button. If you want to see the lyrics, press the [B] button. If the MAIN screen is not displayed, press the [DIRECT ACCESS] button followed by the [EXIT] button. If the selected song does not contain lyric data, lyrics are not displayed. 7 Press the SONG [START/STOP] button and play the part. REC TOP SYNC.START NEW SONG 8 Press the SONG [START/STOP] button to stop playback. REC NEW SONG 36 START / STOP Quick Guide TOP START / STOP SYNC.START • If you want to start the song right away without an intro, use the Sync Start function. To set Sync Start to standby, simultaneously hold down the [TOP] button and press the SONG [START/STOP] button. Song playback starts automatically the moment you start playing the melody. • If you can hear the Clavinova playing the melody part as well, check the channel setting for the melody part in the song data, and change the channel assigned to Track 1 (page 129). You can also change the song channel itself permanently (page 104). Playing and Practicing with the Songs Recording The Clavinova lets you record, too — quickly and easily. Try out the Quick Recording feature now and capture your keyboard performance. 1-3 4 Select a voice for recording. Use the same operations as in “Playing a Voice” on pages 25, 26. Press the [REC] and [TOP] buttons simultaneously to select “New Song“ for recording. REC TOP NEW SONG 5 START / STOP REW FF REPEAT SYNC.START Simultaneously hold down the [REC] button and press the [TRACK1] button. REC SONG EXTRA TRACKS (STYLE) TRACK 2 (L) TRACK 1 (R) 6 Recording starts as soon as you start playing the keyboard. 7 When you’ve finished recording, press the [REC] button. REC 8 To hear your newly recorded performance, return the song to the beginning by using the [TOP] button and press the SONG [START/STOP] button. REC NEW SONG 9 TOP START / STOP SYNC.START CAUTION The recorded data will be lost if you turn off the power. To keep your important recordings, you’ll need to save them to the User drive or floppy disk. Save the recorded data as required (pages 39, 45). Quick Guide 37 Playing and Practicing with the Songs Mastering Your Favorite Songs The Clavinova has several very useful practice features that help learn and master recorded songs. Here, you’ll try out the Follow Lights function, and use the special guide lamps to help you play the right notes. 1-6 7 Use the same operations as in “Playing Along with the Clavinova” on page 36. For this example, you practice the right hand part of “Playing Along with the Clavinova.” Before Practicing Before starting a practice session, play back the entire song (without canceling any parts) and listen to it carefully. This will give you a clear idea of how the song should be played, and will make your practice sessions progress more smoothly. If you want to hear only the melody part, turn the [TRACK 2] and [EXTRA TRACKS] buttons off. Press the [GUIDE] button. GUIDE 8 Press the SONG [START/STOP] button and practice the missing (muted) part, according to the key guide lamps. If you want, you can adjust the tempo by pressing the TEMPO[ ] [ ] buttons. REC TOP START / STOP TEMPO RESET SYNC.START NEW SONG 9 10 You can use the powerful Repeat function to practice and master difficult parts. Simply specify a short phrase you want to work on and repeat it until you’ve got it down. 1) While the song is playing back, press the [GUIDE] button once to turn the GUIDE function off. 2) Just before the desired phrase comes around, press the [REPEAT] button to designate the beginning point for Repeat. 3) Just after the phrase finishes, press the [REPEAT] button again to designate the end point. 4) Turn the GUIDE function on again. Press the SONG [START/STOP] button to stop playback. REC NEW SONG 38 Quick Guide TOP START / STOP SYNC.START See pages 79 and 129 for more information on the Guide function. Basic Operations — Organizing Your Data The CVP-205/203 utilizes a variety of data types — including voices, accompaniment styles, songs and registration memory settings. Much of this data is already programmed and contained in the CVP-205/203; you can also create and edit your own data with some of the functions on the instrument. All this data is stored in separate files — just as is done on a computer. Here, we’ll show you how to use the basic operations of the display controls in handling and organizing the data of the CVP-205/203 in files and folders. Files can be opened, saved, named, moved, or deleted in their respective Open/Save displays. You can select these displays according to their respective file types, as well: Song, Voice, Style, etc. Moreover, you can organize your data efficiently by putting various files of the same type into a single folder. The Open/Save displays for Song, Voice, Style, and Registration Bank can be called up from the MAIN display (the display shown when the power is turned on) by pressing the appropriate [A] - [J] button. Open/Save display for Song (page 75) Open/Save display for Voice (page 55) handles the Song files. handles the Voice files. A F B G C H D I E J The following Open/Save display types are also available; however, these are selected from displays other than the MAIN display (page 143). • SYSTEM SETUP • MIDI SETUP • USER EFFECT • MUSIC FINDER If the MAIN screen is not displayed, press the [DIRECT ACCESS] button followed by the [EXIT] button. Open/Save display for Style (page 60) handles the Style files. Open/Save display for Registration Bank (page 86) handles the Registration Bank files. CVP-205/203 39 Basic Operations — Organizing Your Data Example — Open/Save display for Voice Each Open/Save display consists of PRESET, USER, and FLOPPY DISK drive pages. PRESET drive The files that are preprogrammed and installed internally to the CVP-205/203 are kept here. Preset files can be loaded but cannot be re-written. However, you can use a preset file as a basis for creating your own original file (which can be saved in the USER or FLOPPY DISK drive). USER drive Files kept here are those containing your own original data, created or edited using the various functions of the CVP205/203. They are stored internally to the CVP-205/203. FLOPPY DISK drive You can also store your original data to floppy disk. Commercially available disk software can also be called up here. Naturally, these files are available only when the appropriate disk is inserted in the floppy disk drive. BACK NEXT Changes drives among PRESET, USER and FLOPPY DISK. Calls up the upper level directory page. In this example, the voice folder selection page can be called up. File All data, both preprogrammed and your own original, are stored as “files.” 40 CVP-205/203 Current Memory “Current Memory” is the area where the voice is called up when you select a voice. Also it is the area where you edit your voice using the SOUND CREATOR function. Your edited voice should then be saved as a file in the USER or FLOPPY DISK drive. Recording songs (page 93) and creating accompaniment styles (page 109) are done within the current memory. Please make sure to properly save this data to the USER/FLOPPY DISK drive as a file or files. The data will be lost if you turn off the power without saving. Basic Operations — Organizing Your Data Selecting Files and Folders Select a file shown in the display. In this example, we’ll select a voice file. First, press the VOICE [PIANO & HARPSI] button to call up the display containing the files. This display (“Open/Save” display) is typical of those used to call up and store files (voice files). The CVP-205/203 already contains a variety of voices in the PRESET section. You can store your own original voices created with the Sound Creator function to the USER or FLOPPY DISK section. BACK NEXT “PRESET,” “USER,” or 1 Select “FLOPPY DISK” by using the [BACK][NEXT] button. ENTER DATA ENTRY 3 Select the file/folder. the [1▲] ~ [7▲] buttons to 2 Use turn the pages. When the amount of available files or folders exceeds ten, the bottom of the display changes as shown below. Press Prev.(previous) END Press Next There are two ways to select the file/ folder: • Press the [A] - [J] button. Press the letter button corresponding to the file/folder you wish to call up. (In the example display shown above, the voice files are shown.) • Use the [DATA ENTRY] dial and the [ENTER] button. When you turn the [DATA ENTRY] dial, the highlight moves among the available files/folders. Highlight the desired file or folder (voice files are shown in the example above) and press the [ENTER] button to call up the selected item. Press the [EXIT] button to go back to the MAIN display. You can go back to the previous display by pressing the [EXIT] button. When “JAPANESE” is selected for the Language parameter (pages 50, 143), and you change this to one of the western languages, the kanji and kana characters of the file name stored in the disk drive are changed to western characters. In the opposite case, special Latin characters and marks are changed into normal characters. Also, in the case of floppy disk data, text in the files are changed to characters that cannot be read by the instrument. Keep in mind that similar problems may occur when trying to access files originating or edited by a computer having a different language operating system. In general, be careful when switching languages — you risk not being able to access the data properly. Double-clicking the appropriate [A] -[J] button calls up the corresponding file and returns to the MAIN display. Highlighting the desired file and double-clicking the [ENTER] button calls up the corresponding file and returns to the MAIN display. Exiting from small pop-up windows You can also exit from small pop-up windows (such as in the illustration below) by pressing the [EXIT] button. CVP-205/203 41 Basic Operations — Organizing Your Data File/Folder-related Operations Naming Files/Folders You can assign names to files and folders. Any file/folder in the USER and FLOPPY DISK sections can be named or renamed. Execute the following steps when there is data in the User drive. If there are Preset files/folders you wish to rename, copy them beforehand (page 44) and use them as User files/folders. 1 Press the [1▼] (NAME) button (page 39). The NAME display appears. 2 Select the appropriate file/folder and press the [7▼](OK) button. The currently selected file/folder is highlighted. To select another file/folder, press one of the [A] - [J] buttons. A file/folder name can contain up to 50 half size letters (or 25 Hiragana and kanji letters), including the Icon ID (see the note below) and the extension. The file name will appear on your computer as follows. If you change the Icon ID or the extension, the icon may change or the file may not be properly recognized. ABCDE.S002.MID File ID Icon ID Extension END Input the new name (page 46). Press the [8▲] (OK) button. To cancel, press the [8▼] (CANCEL) button. 42 CVP-205/203 Basic Operations — Organizing Your Data Moving Files/Folders You can move files and folders as desired, for organizing your data. Any file/folder in the USER and FLOPPY DISK sections can be moved, using the cut-and-paste operation described below. the [2▼] (CUT) button (page 39). 1 Press The CUT display appears. 2 Select the desired file/folder for moving. Select the appropriate file/folder and press the [7▼](OK) button. The currently selected file/folder is highlighted. To select another file/folder, press one of the [A] [J] buttons. Several files/folders can be selected together, even those from other pages. To release or cancel the selection, press the button of the selected file/folder again. Press the [6▼] (ALL) button to select all the files/folders in the displayed page (USER/FLOPPY DISK). When the [6▼] (ALL) button is pressed the [6▼] button changes to “ALL OFF” button to release or cancel the selection. 3 Press the [7▼] (OK) button. This operation cannot be used to directly move a file/ folder from one floppy disk to another. If you want to do this, cut and paste the file or folder from the first floppy disk to the USER page, then change disks and paste it to the FLOPPY DISK page. All files/folders in a floppy disk can be copied to another disk in one batch (page 142). After being pasted, the files are automatically re-ordered in alphabetical order and displayed. To stop the operation, press the [8▼] (CANCEL) button. 4 Call up the destination display. Only the USER and FLOPPY DISK pages can be selected as the destination. END Press the [4▼] (PASTE) button. The file/folder you cut is now pasted at the destination. About files/folders in a floppy disk In the FLOPPY DISK page of the Open/Save display, only the files which can be handled in that Open/Save display will appear — even though a folder in a floppy disk can contain different kinds of files. In the case of a folder cutand-paste operation (for floppy disk), an entire folder can be cut; however, only the specific files which can be handled in the current Open/ Save display will be pasted. CVP-205/203 43 Basic Operations — Organizing Your Data Copying Files/Folders You can also copy files and folders as desired, for organizing your data. Any file/folder in the PRESET, USER and FLOPPY DISK sections can be copied, using the copy-and-paste operation described below. Press the [3▼] (COPY) button 1 (page 39). The COPY display appears. 3 Press the [7▼] (OK) button. To stop the operation, press the [8▼] (CANCEL) button. 4 Call up the destination display. Only the USER and FLOPPY DISK pages can be selected as the destination. 2 Select the desired file/folder. Select the appropriate file/folder and press the [7▼](OK) button. The currently selected file/folder is highlighted. To select another file/ folder, press one of the [A] - [J] buttons. Several files/folders can be selected together, even those from other pages. To release or cancel the selection, press the button of the selected file/folder again. Press the [6▼] (ALL) button to select all the files/folders in the displayed page (PRESET/USER/ FLOPPY DISK). When the [6▼] (ALL) button is pressed, the [6▼] button changes to “ALL OFF,” letting you release or cancel the selection. END Please note that the copy functions are intended for your personal use only. This operation cannot be used to directly copy a file/ folder from one floppy disk to another. If you want to do this, copy and paste the file or folder from the first floppy disk to the User page, then change disks and paste it to the Floppy Disk page. Press the [4▼] (PASTE) button. The file/folder you copied is now pasted at the destination. Deleting Files/Folders You can also delete files and folders as desired, for organizing your data. Any file/folder in the USER and FLOPPY DISK sections can be deleted, using the operation described below. 1 Press the [5▼] (DELETE) button (page 39). The DELETE display appears. END Press the [7▼] (OK) button. To cancel the operation, press the [8▼] (CANCEL) button. The message “Are you sure you want to delete the “******” file (or data/folder)? YES/NO” appears. YES ..........Deletes the highlighted item. NO............Exits from the prompt without deleting. 2 44 Select the desired file/folder. Select the appropriate file/folder and press the [7▼](OK) button. The currently selected file/folder is highlighted. To select another file/folder, press one of the [A] - [J] buttons. Several files/folders can be selected together, even those from other pages. To release or cancel the selection, press the button of the selected file/folder again. Press the [6▼] (ALL) button to select all the files/folders in the displayed page (USER/FLOPPY DISK). When the [6▼] (ALL) button is pressed, the [6▼] button changes to “ALL OFF,” letting you release or cancel the selection. CVP-205/203 When several files have been selected, the message “Are you sure you want to delete the “******” file (or data/folder)? YES/YES ALL/NO/CANCEL” appears. YES/NO...... Deletes the highlighted item (YES), or skips the highlighted item without deleting (NO). YES ALL .... Deletes all selected items at once. CANCEL .... Exits from the prompt without deleting. Basic Operations — Organizing Your Data Saving Files This operation lets you save the data (such as song and voice) you created in current memory (page 40) to files. The files can be saved only to the USER and FLOPPY DISK drives. If the Open/Save display for the type of data you wish to save is not shown, first return to the MAIN display by pressing the [DIRECT ACCESS] button followed by the [EXIT] button. Then, press the appropriate button [A]–[J] from the MAIN display to call up the respective Open/Save display. Finally, call up the USER or FLOPPY DISK page (pages 39, 40). the [6▼] 1 Press (SAVE) button. Enter a name for the new file (page 46). Press the [8▲] (OK) button. To stop the operation, press the [8▼] (CANCEL) button. The internal memory capacity of the Clavinova is about 580KB. Memory capacity for 2DD and 2HD floppy disks is about 720KB and 1.44MB, respectively. When you store data to these locations, all file types of the Clavinova (Voice, Style, Song, Registration, etc.) are stored together. The files of commercially available DOC software and Yamaha Disklavier software, and their edited files on the CVP-205/203, can be stored in the USER page, but cannot be copied to another floppy disk. Organizing Files by Creating a New Folder This operation lets you easily organize your various files into categories by creating a new folder for each category. Folders can only be created in the USER and FLOPPY DISK sections. up the page to 1 Call which you wish to create a new folder and press the [7▼] (NEW) button (page 39). Enter the name of the new folder (page 46). Folder directories can contain up to four levels. The maximum total number of files and folders which can be stored is 800, but this may differ depending on the length of the file names. The maximum number of files which can be stored in a folder will be 250. Press the [8▲](OK) button. To cancel the operation, press the [8▼] (CANCEL) button. Displaying Upper Level pages Press the [8▼] (UP) button to call up the upper level pages. For example, you can call up the folder level pages from the file level pages. Entering Characters and Changing Icons the [1▼] 1 Press (NAME), [6▼] (SAVE), or [7▼] (NEW) button (page 39). Change the type of character by using the [1▲] button. If you select Japanese as the Language in the FUNCTION display (page 143), the following different types of characters and sizes can be entered: (kana-kan) Call up the ICON SELECT display by pressing Hiragana and kanji, marks (full size) the [1▼] button. This lets you change the icon (kana) at the left of the file name. Katakana (normal size), marks (full size) (kana) Katakana (half size), marks (half size) A B C — Alphabet (capital and small letters, full size), numbers (full size), marks (full size) ABC — Alphabet (capital and small letters, half size), numbers (half size), marks (half size) If you’ve selected a language other than Japanese in the FUNCTION display (page 143), the following types of characters are available: CASE — Alphabet (capital letters, half size), numbers (half size), marks (half size) case — Alphabet (lowercase letters, half size), numbers (half size), marks (half size) CVP-205/203 45 Basic Operations — Organizing Your Data Entering Characters The instructions that follow show you how to enter characters in naming your files and folders. The method is much the same as inputting names and numbers to your cell phone. 1 2 3 Move the cursor to the desired position by using the [DATA ENTRY] dial. Press the appropriate button, [2▲] - [7▲] and [2▼]- [6▼], corresponding to the character you wish to enter. Several different characters are assigned to each button, and the characters change each time you press the button. To actually enter the selected character, move the cursor or press another letter-input button. If you’ve entered a character by mistake, move the cursor to the character letter you wish to erase and press the [7▼] (DELETE) button. If you want to delete all of the characters on the line at once, press and hold down the [7▼] (DELETE) button for a while, or press the [8▼] (CANCEL) button. When the cursor appears in reverse display (highlight), only the reversed area is deleted. To actually enter the new name, press the [8▲] (OK) button. To cancel the operation, press the [8▼] (CANCEL) button. ■ Converting into Kanji (Japanese language) This applies only if you are using the “ (kana-kan)” button (in Japanese). When the input “hiragana” characters are shown in reverse display (highlighted), press the [ENTER] button one or several times to convert the characters into the appropriate kanji. The reversed area can be changed by the [DATA ENTRY] dial. The converted area can be changed back to “hiragana” by the [7▼] (DELETE) button. The reversed area can be cleared at once by the [8▼] (CANCEL) button. To actually enter the change, press the [8▲] (OK) button or enter the next character. To enter the “hiragana” itself (without converting it), press the [8▲] (OK) button. The following half-size marks cannot be used in naming files and folders: ¥\/:*?“<>| ■ Entering special character marks (umlaut, accent, Japanese “ ” and “ ”) Select a character to which a character mark is to be added and press the [6▼] button (before actual entry of the character.) ■ Entering miscellaneous characters (marks) You can call up the mark list by pressing the [6▼] button, after actually entering a character by moving the cursor. Move the cursor to the desired mark by using the [DATA ENTRY] dial, then press the [8▲] (OK) or [ENTER] button. ■ Entering numbers First, select one of the following: “A B C” (full-size alphabet), “ABC” “CASE” (half-size capital alphabet) and “case” (half-size lowercase alphabet). Then, press and hold down the appropriate button, [2▲] - [7▲] and [2▼] - [5▼], for a while, or press it repeatedly until the desired number is selected. 46 CVP-205/203 In the case of characters which are not accompanied by special character marks (with the exception of kanakan and half-size katakana), you can call up the mark list by pressing the [6▼] button after selecting a character (before actual entry of a character). Basic Operations — Organizing Your Data Changing the Icon You can also change the icon that appears at the left of the file name. Call up the ICON SELECT display by pressing the [1▼] (ICON) button from the character input display (page 46). Select the desired icon by using the [A] - [J] buttons, or by using the [3▲▼] - [5▲▼] buttons, then enter the selected icon by pressing the [8▲] (OK) button. BACK NEXT Turns pages for icon selection. Enters the selected icon. Cancels the icon selection operation. Using the [DATA ENTRY] Dial This convenient control lets you easily select items in the display or quickly change parameter values. The actual function of the [DATA ENTRY] dial differs depending on the selected display. ■ Adjusting values You can change parameter values by rotating the [DATA ENTRY] dial. In the example [BALANCE] display, turning the dial adjusts the volume of the part in reverse display (highlight). To adjust the volume of another part, first select the part by pressing the [▲▼] button corresponding to the part, then rotate the [DATA ENTRY] dial. DATA ENTRY ■ Selecting items You can select the desired item or function in the display by rotating the [DATA ENTRY] dial. The selected item can then be called up or executed by using the [ENTER] button. In the example VOICE display, you can select the desired voice file with the [DATA ENTRY] dial, and call up the selected item by pressing the [ENTER] button on the panel. ENTER DATA ENTRY CVP-205/203 47 Basic Operations — Organizing Your Data Direct Access — Instant Selection of Displays DIRECT ACCESS METRONOME POWER ON OFF START STOP SONG EXTRA TRACKS (STYLE) TRACK 2 (L) LCD CONTRAST TRACK 1 (R) BACK MENU REC TOP START / STOP REW FF REPEAT TEMPO TRANSPOSE TAP TEMPO RESET RESET STYLE AUTO FILLIN BREAK INTRO OTS LINK ENDING / rit. MAIN A HELP A F FUNCTION B G LAYER C H LEFT D I B C D E J DIGITAL STUDIO SOUND CREATOR MAX MIN PIANO & HARPSI. VARIATION HARMONY / ECHO MONO LEFT HOLD ORGAN & ACCORDION PERCUSSION GUITAR BASS WOODWIND STRINGS CHOIR & PAD SYNTH. XG VOICE PART ON / OFF BRASS USER ENTER SYNC.START NEW SONG FADE IN / OUT ACMP DSP E.PIANO VOICE GUIDE MASTER VOLUME VOICE EFFECT REVERB NEXT DEMO SYNC.STOP SYNC.START START / STOP DIGITAL RECORDING MIXING CONSOLE ONE TOUCH SETTING MUSIC FINDER 1 DATA ENTRY BALANCE PIANO 2 3 4 REGISTRATION MEMORY FREEZE 1 2 3 4 5 6 7 8 MEMORY PART CHANNEL ON / OFF PART DIRECT ACCESS 1 2 3 4 5 6 7 8 EXIT With the convenient Direct Access function, you can instantly call up the desired display — with just a single additional button press. Press the [DIRECT ACCESS] button and a message appears in the display prompting you to press the appropriate button. Then, simply press the button corresponding to the desired setting display to instantly call up that display. In the example below, Direct Access is used to call up the display for selecting the Chord Fingering (page 131). ACMP DIRECT ACCESS Refer to the Direct Access Chart (page 49) for a list of the displays that can be called up with the Direct Access function. 48 CVP-205/203 Here’s a convenient way to return to the MAIN display from any other display: Simply press the [DIRECT ACCESS] button, then the [EXIT] button. Basic Operations — Organizing Your Data Direct Access Chart Operation: [DIRECT ACCESS] button + button listed below STYLE [ACMP] [BREAK] [INTRO] MAIN [A] MAIN [B] MAIN [C] MAIN [D] [ENDING] [AUTO FILL IN] [OTS LINK] [SYNC. STOP] [SYNC. START] [START/STOP] SONG [TRACK1] [TRACK2] [EXTRA TRACKS] [REPEAT] [GUIDE] [REC] [TOP] [START/STOP] [REW] [FF] METRONOME [START/STOP] [FADE IN/OUT] TEMPO [TAP TEMPO] [E] [ ] TRANSPOSE [E] [ ] MENU [DEMO] [HELP] [FUNCTION] DIGITAL STUDIO [SOUND CREATOR] [DIGITAL RECORDING] [MIXING CONSOLE] [BALANCE] [CHANNEL ON/OFF] [DIRECT ACCESS] [NEXT] [BACK] [ENTER] [EXIT] VOICE PART [LAYER] [LEFT] VOICE EFFECT [REVERB] [DSP] [VARIATION] [HARMONY/ECHO] [MONO] [LEFT HOLD] VOICE [PIANO & HARPSI] [E.PIANO] [ORGAN & ACCORDION] [PERCUSSION] [GUITAR] [BASS] [BRASS] [WOODWIND] [STRINGS] [CHOIR & PAD] [SYNTH.] [XG] [USER] [MUSIC FINDER] ONE TOUCH SETTING [1] [2] [3] [4] [PIANO] REGISTRATION MEMORY [FREEZE] [1] [2] [3] [4] [5] [6] [7] [8] [MEMORY] PEDAL RIGHT CENTER LEFT AUX FUNCTION MIXING CONSOLE (STYLE PART) FUNCTION Corresponding LCD display and function CHORD FINGERING FINGERING TYPE selection VOICE settings VOLUME/VOICE PANPOT settings VOLUME settings HARMONIC CONTENT settings FILTER BRIGHTNESS settings REVERB settings EFFECT CHORUS settings DSP settings STYLE SETTING/SPLIT POINT See pages 131 120 121 122 130 SYNC. STOP WINDOW setting — — TRACK1 CHANNEL selection TRACK2 CHANNEL selection FUNCTION SONG SETTING 129 GUIDE MODE selection — — — — — UTILITY METRONOME settings FADE IN/OUT settings TAP settings MIDI MIDI CLOCK setting FUNCTION E MIXING CONSOLE CONTROLLER TUNE 138 133 121 143 141 137 TRANSPOSE settings LANGUAGE selection LCD BRIGHTNESS settings MIDI settings MASTER TUNING setting SCALE TUNING setting UTILITY FUNCTION 140 MIDI MASTER TUNE/SCALE TUNE 127 — MIXING CONSOLE (SONG PART) VOLUME settings VOICE settings 120 TUNE OCTAVE settings 121 EFFECT REVERB settings DSP settings EFFECT TYPE selection 122 VOLUME/VOICE Exit from the Direct Access mode — — — Return to the MAIN display MIXING CONSOLE FUNCTION MIXING CONSOLE HARMONY/ECHO TUNE PORTAMENTO TIME settings STYLE SETTING/SPLIT POINT SPLIT POINT (LEFT) setting 135 121 130 VOICE SET 135 MUSIC FINDER SEARCH1 (Searching the records) — — — — KEYBOARD TOUCH selection CONTROLLER FREEZE 71 133 134 REGISTRATION BANK REGISTRATION EDIT (Editing the REGISTRATION) 86 134 FUNCTION REGISTRATION SEQUENCE (Creating the REGISTRATION SEQUENCE) RIGHT PEDAL function assignment CENTER PEDAL function assignment CONTROLLER LEFT PEDAL function assignment AUX PEDAL function assignment FUNCTION MUSIC FINDER FUNCTION 131 CVP-205/203 49 E Basic Operations — Organizing Your Data Help Messages The Help messages give you explanations and descriptions of all the main functions and features of the CVP-205/203. HELP METRONOME POWER ON OFF START STOP SONG EXTRA TRACKS (STYLE) TRACK 2 (L) LCD CONTRAST TRACK 1 (R) BACK MENU TOP START / STOP REW FF REPEAT FADE IN / OUT TEMPO TRANSPOSE TAP TEMPO RESET RESET STYLE AUTO FILLIN BREAK INTRO ENDING / rit. MAIN A HARMONY / ECHO MONO LEFT HOLD PERCUSSION GUITAR BASS WOODWIND STRINGS CHOIR & PAD SYNTH. XG VOICE PART HELP A F FUNCTION B G LAYER C H LEFT B C DIGITAL STUDIO SOUND CREATOR MAX MIN VARIATION ORGAN & ACCORDION ON / OFF BRASS USER ENTER SYNC.START NEW SONG ACMP PIANO & HARPSI. GUIDE MASTER VOLUME DSP E.PIANO VOICE DEMO REC VOICE EFFECT REVERB NEXT SYNC.STOP SYNC.START START / STOP D DIGITAL RECORDING MIXING CONSOLE D I E J ONE TOUCH SETTING MUSIC FINDER 1 DATA ENTRY BALANCE PIANO 2 3 4 REGISTRATION MEMORY FREEZE 1 2 3 4 5 6 7 8 MEMORY PART CHANNEL OTS LINK ON / OFF PART DIRECT ACCESS 1 MENU 1 2 3 4 5 6 7 8 EXIT 2 Help messages can be displayed in any one of the following languages: ENGLISH JAPANESE GERMAN FRENCH SPANISH ITALIAN DEMO HELP FUNCTION The language can also be selected in the FUNCTION “LANGUAGE” (page 143) display. 2-1 Select the desired Help topic. 2-2 Call up the topic. Select the Language, if necessary. The language selected here are also used for various “Messages” shown during operations. 3 BACK NEXT Use this to select different pages. When “JAPANESE” is selected for the Language parameter, and you change this to one of the western languages, the kanji and kana characters of the file name stored in the disk drive are changed to western characters. In the opposite case, special Latin characters and marks are changed into normal characters. Also, in the case of floppy disk data, text in the files are changed to characters that cannot be read by the instrument. Keep in mind that similar problems may occur when trying to access files originating or edited by a computer having a different language operating system. In general, be careful when switching languages — you risk not being able to access the data properly. ENTER END DATA ENTRY Help messages also feature links to the detailed explanation or actual setting display of the selected topic. Simply select the underlined word (using the [DATA ENTRY] dial), and press the [ENTER] button to jump to the detailed explanation or actual setting display of the selected topic. 50 CVP-205/203 Press this to return to the previous display. EXIT Basic Operations — Organizing Your Data Using the Metronome The metronome provides a click sound, giving you an accurate tempo guide when you practice, or letting you hear and check how a specific tempo sounds. METRONOME START METRONOME POWER ON STOP OFF START SONG EXTRA TRACKS (STYLE) STOP TRACK 2 (L) LCD CONTRAST TRACK 1 (R) BACK MENU REC TOP START / STOP REW FF REPEAT GUIDE TEMPO A F B G LAYER C H LEFT DIGITAL STUDIO TRANSPOSE TAP TEMPO SOUND CREATOR MAX RESET DIGITAL RECORDING RESET STYLE INTRO BREAK HARMONY / ECHO MONO LEFT HOLD PERCUSSION GUITAR BASS WOODWIND STRINGS CHOIR & PAD SYNTH. XG ON / OFF BRASS USER ENTER SYNC.START NEW SONG AUTO FILLIN VARIATION ORGAN & ACCORDION VOICE PART HELP FUNCTION FADE IN / OUT MIN DSP E.PIANO VOICE PIANO & HARPSI. MASTER VOLUME ACMP VOICE EFFECT REVERB NEXT DEMO ENDING / rit. MAIN A B C SYNC.STOP SYNC.START START / STOP MIXING CONSOLE D D I E J ONE TOUCH SETTING MUSIC FINDER 1 DATA ENTRY BALANCE 2 3 4 REGISTRATION MEMORY PIANO FREEZE 1 2 3 4 5 6 7 8 MEMORY PART CHANNEL OTS LINK ON / OFF PART 1 DIRECT ACCESS 2 3 4 5 6 7 8 EXIT The metronome starts by pressing the METRONOME [START/STOP] button. Adjust the tempo by using the TEMPO[ ] [ ] buttons (see below). To stop the metronome, press the [START/STOP] button again. The sound, volume level, and the beat (time signature) of the metronome can all be changed (page 140). Adjusting the Tempo This section shows you to adjust the playback tempo — which not only affects the metronome, but also the playback of a song or an accompaniment style. TEMPO TAP TEMPO RESET METRONOME POWER ON OFF START STOP SONG EXTRA TRACKS (STYLE) TRACK 2 (L) LCD CONTRAST TRACK 1 (R) BACK MENU REC TOP START / STOP REW FF REPEAT FADE IN / OUT TEMPO TRANSPOSE TAP TEMPO MIN MAX RESET BREAK INTRO RESET ENDING / rit. MAIN A HARMONY / ECHO MONO LEFT HOLD PERCUSSION GUITAR BASS WOODWIND STRINGS CHOIR & PAD SYNTH. XG VOICE PART HELP A F FUNCTION B G LAYER C H LEFT D I E J B C DIGITAL STUDIO SOUND CREATOR STYLE AUTO FILLIN VARIATION ORGAN & ACCORDION PIANO & HARPSI. ON / OFF BRASS USER ENTER SYNC.START NEW SONG ACMP DSP E.PIANO VOICE GUIDE MASTER VOLUME VOICE EFFECT REVERB NEXT DEMO SYNC.STOP SYNC.START START / STOP D DIGITAL RECORDING MIXING CONSOLE ONE TOUCH SETTING MUSIC FINDER 1 DATA ENTRY BALANCE 2 3 4 REGISTRATION MEMORY PIANO FREEZE 1 2 3 4 5 6 7 8 MEMORY PART CHANNEL OTS LINK ON / OFF PART 1 DIRECT ACCESS 1 TEMPO TAP TEMPO 2 3 4 5 6 7 8 EXIT 2 RESET Press either the TEMPO [ button or the [ ] button. E Press this to ND close the TEMPO display. Songs and accompaniment styles have been given default (initial) tempo settings, designed to best suit the song/style. Adjust the tempo by using either the TEMPO [ ] [ ] buttons or the [DATA ENTRY] dial. The number in the display indicates how many quarter-note beats there are in one minute. The range is between 5 and 500. The higher the value, the faster the tempo. ] EXIT When you change the tempo, both tempos of the current song and style will be changed to the same tempo. To restore their respective default (initial) tempo settings, press both the TEMPO [ ] [ ] buttons simultaneously. Also refer to the “Tempo Indications — MAIN display” (page 52) for more about tempo. CVP-205/203 51 Basic Operations — Organizing Your Data Tap Tempo This useful feature lets you tap out the tempo for a song or an accompaniment style. Simply tap the [TAP TEMPO] button at the desired speed, and the tempo of the song or the accompaniment style changes to match your tapping. the song or the 1 Playback accompaniment style (page 60, 75). 2 TEMPO TAP TEMPO RESET Tap the [TAP TEMPO] button twice to change the tempo. ■ Tempo Indications — MAIN Display There are three different tempo indications in the Main display, as shown below. Indicates the default (initial) tempo setting for the currently selected song (unless the tempo has been changed manually). Indicates the current tempo for the selected song, accompaniment style or the metronome which is now playing back. When nothing is playing back (stopped), this indicates the tempo for the selected style. When the song and style are played back simultaneously, the tempo of the style is automatically changed to match the tempo of the song, and is displayed here. This tempo is used for recording when recording a song or accompaniment style. Indicates the default (initial) tempo setting for the currently selected accompaniment style (unless the tempo has been changed manually). 52 CVP-205/203 Hitting the [TAP TEMPO] button produces a tapping sound. You can change this sound, if desired (page 141). n You can also use Tap Tempo to automatically start the song or accompaniment style at the desired tempo. While both the song and accompaniment style are stopped, tap the [TAP TEMPO] button several times, and the selected accompaniment style starts automatically at the tempo you tapped. While a song is set to Sync. Start stand-by (page 61, 75), tapping the [TAP TEMPO] button starts the song playback in the same manner. For songs and styles in 2/4 and 4/4 time, tap four times; for 3/4 time, tap three times; for 5/4 time, tap five times. Playing the Demos The CVP-205/203 is an extraordinarily versatile and sophisticated instrument, featuring a wide variety of dynamic Reference voices and rhythms, plus a wealth of advanced functions. Three different types of Demo songs have been specially prepared showcasing the stunning sound and features of the CVP-205/203. MENU DEMO METRONOME POWER ON OFF START STOP SONG EXTRA TRACKS (STYLE) TRACK 2 (L) LCD CONTRAST TRACK 1 (R) TOP START / STOP REW FF SYNC.START A F B G LAYER C H LEFT DIGITAL STUDIO TRANSPOSE TAP TEMPO MIN SOUND CREATOR MAX RESET DIGITAL RECORDING RESET STYLE ACMP AUTO FILLIN BREAK INTRO ENDING / rit. MAIN A B C MIXING CONSOLE SYNC.STOP SYNC.START START / STOP D VARIATION HARMONY / ECHO MONO LEFT HOLD ORGAN & ACCORDION PERCUSSION GUITAR BASS WOODWIND STRINGS CHOIR & PAD SYNTH. XG VOICE PART HELP FUNCTION FADE IN / OUT DSP E.PIANO VOICE PIANO & HARPSI. GUIDE FUNCTION TEMPO VOICE EFFECT REVERB NEXT DEMO REPEAT MASTER VOLUME NEW SONG BACK MENU HELP REC D I E J ON / OFF BRASS ONE TOUCH SETTING MUSIC FINDER 1 DATA ENTRY BALANCE USER ENTER PIANO 2 3 4 REGISTRATION MEMORY FREEZE 1 2 3 4 5 6 7 8 MEMORY PART CHANNEL OTS LINK ON / OFF PART 1 Pressing the [DEMO] button automatically plays back the Demo songs at random. MENU DEMO HELP FUNCTION 2 2-1 Use the [BACK][NEXT] buttons to select the desired Demo category. Function Demos ....... These demonstrate each of the different functions on the CVP-205/203. Voice Demos ............. These showcase the voices of the CVP-205/203. Style Demos .............. These introduce you to the rhythms and accompaniment styles of the CVP-205/203. BACK NEXT 2-3 2-2 Use these to select different display pages. Press one of these buttons twice — once to select the desired demo, and once again to start it. Press this to play back all Demo songs/items continuously, starting from the first item at the top left of the display. This is available only from the FUNCTION page. All of the available demos are played back in sequence, starting from the one at top left. The VOICE and STYLE pages do not have the [AUTO] button; however, all demo songs are played back in sequence. Pressing this button cancels the interactive features of the Function Demos (otherwise available in step 3 below). CVP-205/203 53 Playing the Demos 3 For the Function demos, an introduction screen appears in the display and the Demo starts playing. This example shows the Voices in the FUNCTION demo. BACK n NEXT F VOICE PART ON / OFF G LAYER H LEFT ENTER I J DATA ENTRY Select the desired word or item by using the [DATA ENTRY] dial, then press the [ENTER] button or number buttons ([1▼], [2▼], etc.) to call it up. 4 Relevant explanations are shown in the display. END EXIT Return to the MAIN screen. 54 CVP-205/203 Use the [BACK][NEXT] buttons in the introduction screen to call up the previous or next page. Press the SONG [START/ STOP] button to stop the Demo song. To start the Demo again from the point at which it was stopped, press the SONG [START/ STOP] button again. Rewind and fast-forward can also be used with the Demo songs (page 77). Voices The CVP-205/203 gives you an enormous selection of authentic voices, including various keyboard instruments, strings and brass — and many, many more. VOICE PIANO & HARPSI. BRASS ORGAN & ACCORDION PERCUSSION GUITAR BASS WOODWIND STRINGS CHOIR & PAD SYNTH. XG METRONOME POWER ON E.PIANO OFF START STOP SONG EXTRA TRACKS (STYLE) TRACK 2 (L) USER VOICE EFFECT LCD CONTRAST TRACK 1 (R) BACK MENU REVERB TOP START / STOP REW FF REPEAT HELP FUNCTION TEMPO TRANSPOSE TAP TEMPO RESET RESET STYLE BREAK INTRO ENDING / rit. MAIN A B C DIGITAL STUDIO SOUND CREATOR MAX AUTO FILLIN A F HARMONY / ECHO MONO LEFT HOLD PERCUSSION GUITAR BASS STRINGS CHOIR & PAD SYNTH. XG VOICE PART ON / OFF B G LAYER C H LEFT D I BRASS WOODWIND USER ENTER SYNC.START NEW SONG ACMP VARIATION ORGAN & ACCORDION VOICE PIANO & HARPSI. GUIDE FADE IN / OUT MIN DSP E.PIANO NEXT DEMO REC MASTER VOLUME SYNC.STOP SYNC.START START / STOP D DIGITAL RECORDING 1 2 3 4 J E MIXING CONSOLE ONE TOUCH SETTING MUSIC FINDER PIANO DATA ENTRY BALANCE REGISTRATION MEMORY FREEZE 1 2 3 4 5 6 7 8 MEMORY PART CHANNEL OTS LINK ON / OFF PART 1 DIRECT ACCESS 2 3 4 5 6 7 8 EXIT Selecting a Voice 1 2 Select the desired voice group. VOICE PIANO & HARPSI. BRASS E.PIANO ORGAN & ACCORDION PERCUSSION GUITAR BASS WOODWIND STRINGS CHOIR & PAD SYNTH. XG Indicates that the display is for selecting the MAIN voice (page 25). USER When you select a voice group, the last selected voice will automatically be selected. n 2-1 Select the memory location of the voice (PRESET/USER/FLOPPY DISK). BACK Selecting a voice automatically selects the best-suited effect and other settings for that particular voice. You can disable this so that settings are not automatically selected (page 135). n NEXT You can set how much the volume of the voice changes according to your playing strength (page 133). n For a list of the available voices, refer to the separate Data List. n 2-3 2-2 Select the various pages in the current voice group. Press this to call up the display for selecting the voice group. 3 Play the keyboard to hear the selected voice. END Select the voice. Press this to start the demo of the selected voice. To stop the demo at any time, press this button again. Press this to return to the MAIN display. You can set whether the voice bank and program change numbers (“MSBLSB-Program Change number” at the right above the voice name) are displayed or not (page 141). n XG is a major enhancement of the GM System level 1 format, and was developed by Yamaha specially to provide more voices and variations, as well as greater expressive control over voices and effects, and to ensure compatibility of data well into the future. EXIT CVP-205/203 55 Voices Voice Characteristics The voice type and its defining characteristics are indicated above the voice name. Natural! These rich and luscious voices are comprised mostly of keyboard instrument sounds and are especially intended for playing piano and other keyboard parts. Since they use a completely independent sound source, you can play full, sustained chords — even along with the accompaniment style — and not have to worry about notes cutting off. They also take full advantage of Yamaha’s advanced sampling technology such as Stereo Sampling, Dynamic Sampling, Sustain Sampling, and Key-off Sampling. Live! These acoustic instrument sounds were sampled in stereo, to produce a truly authentic, rich sound — full of atmosphere and ambience. Cool! These voices capture the dynamic textures and subtle nuances of electric instruments — thanks to a huge amount of memory and some very sophisticated programming. Sweet! These acoustic instrument sounds also benefit from Yamaha’s sophisticated technology — and feature a sound so finely detailed and natural, you’ll swear you’re playing the real thing! Drum Various drum and percussion sounds are assigned to individual keys, letting you play the sounds from the keyboard. SFX Various special effect sounds are assigned to individual keys, letting you play the sounds from the keyboard. Keyboard Percussion When one of the drum of SFX kits is selected in the PERCUSSION voice group, various drum, percussion, and special effect sounds are assigned to individual keys, letting you play the sounds from the keyboard. The various drums and percussion instruments of the Standard Kit are indicated by symbols above the assigned keys. Keep in mind that even though different kits feature different sounds, some same-named sounds in different kits are identical. Refer to the separate Data List (Drum/key Assignment List) for a listing of the sounds in each drum/SFX kit. One-touch Piano Play This convenient, easy-to-use feature completely and automatically reconfigures the entire CVP-205/203 for optimum piano performance. No matter what settings you’ve made from the panel, you can instantly call up the piano settings by a single button press. PIANO PIANO button This reconfigures all of the panel settings for playing the CVP-205/203 as a piano. Piano Lock function The convenient Piano Lock function lets you “lock” the piano so that you don’t inadvertently change the settings by pressing another button on the panel. Once locked, the CVP-205/203 stays in the piano mode, even if other buttons are pressed — preventing you from accidently starting a song or accompaniment style during a piano concert. Hold down the [PIANO] button for a short time, until a message appears prompting you to enable Piano Lock. To enable Piano Lock, select “OK.” To turn Piano Lock off, hold down the [PIANO] button again for a short time. 56 CVP-205/203 You can also use the metronome with this function (page 51). Even if you turn Piano Lock off, the piano settings are still active. Voices Layer/Left — Playing Several Sounds Simultaneously The CVP-205/203 lets you set three voices for simultaneous play: MAIN, LAYER, and LEFT. By effectively combining these three, you can create richly textured, multi-instrument setups for your performance. VOICE PART ON / OFF METRONOME POWER ON OFF SONG EXTRA TRACKS (STYLE) START STOP TRACK 2 (L) LCD CONTRAST TRACK 1 (R) BACK MENU REC TOP START / STOP REW FF REPEAT GUIDE HELP FUNCTION TEMPO DIGITAL STUDIO TRANSPOSE TAP TEMPO SOUND CREATOR MAX RESET DIGITAL RECORDING RESET STYLE AUTO FILLIN BREAK INTRO ENDING / rit. MAIN A VARIATION HARMONY / ECHO MONO LEFT HOLD ORGAN & ACCORDION PERCUSSION GUITAR BASS STRINGS CHOIR & PAD SYNTH. XG VOICE PART A F B G LAYER C H LEFT H LEFT ON / OFF BRASS WOODWIND USER ENTER SYNC.START NEW SONG MIN DSP E.PIANO VOICE PIANO & HARPSI. FADE IN / OUT ACMP LAYER VOICE EFFECT REVERB NEXT DEMO MASTER VOLUME G B C SYNC.STOP SYNC.START START / STOP D MIXING CONSOLE D I E J ONE TOUCH SETTING MUSIC FINDER 1 DATA ENTRY BALANCE 2 3 4 REGISTRATION MEMORY PIANO FREEZE 1 2 3 4 5 6 7 8 MEMORY PART CHANNEL OTS LINK ON / OFF PART DIRECT ACCESS 1 2 3 4 5 6 7 8 EXIT Playing a layer of two voices LAYER part MAIN part Playing two voices separately — on the left and right sections of the keyboard Split point LEFT part MAIN part Left range Playing three different voices — one on the left section of the keyboard, plus a layer of two on the right Right range Split point LAYER part LEFT part MAIN part Left range Right range Layer — Layering Two Different Voices 1 Press this to turn the LAYER function on. To turn it off, press the button again. VOICE PART ON / OFF G LAYER H LEFT 2 Select LAYER with the [G] button. Press the same button to call up the VOICE display, from which you can select the specific voice you want to play in a layer with the Main voice. The method of selecting a voice here is the same as that in VOICE (MAIN) display (page 55). END EXIT There is an alternate way for quickly selecting both the MAIN and LAYER voices from the panel: While holding down one panel voice button, press a second voice button. The first selected voice becomes the MAIN voice, and the second becomes the LAYER. Press this to return to the MAIN display. CVP-205/203 57 Voices Left — Setting Separate Voices for the Left and Right Sections of the Keyboard 1 2 Set the LEFT to ON. Press this button again to set it to OFF. Select LEFT with the [H] button. Press the same button to call up the VOICE display, from which you can select the specific voice you want to play in a left. How to select the voice is the same as the way of VOICE (MAIN) screen (page 55). LAYER LEFT F The split point can be freely set to any key on the keyboard. To set it, call up the SPLIT POINT display by pressing the [I] (SPLIT POINT) button in the MAIN display. The operation steps are the same as in the STYLE SETTING/SPLIT POINT display of the FUNCTION page (page 130). G n H Each part (MAIN, LAYER, and LEFT) can have its own volume setting (page 62). END n You can also use the LAYER and LEFT functions together, to create a combination layer/split. To do this, set separate voices for the left and right sections of the keyboard (as indicated), and set up a layer of two different voices on the right. EXIT Press this to return to the MAIN display. Applying Voice Effects This section of the panel lets you add a variety of effects to the voices you play on the keyboard. VOICE EFFECT REVERB METRONOME POWER ON OFF START STOP DSP VARIATION HARMONY / ECHO MONO SONG EXTRA TRACKS (STYLE) TRACK 2 (L) LEFT HOLD LCD CONTRAST TRACK 1 (R) BACK MENU TOP START / STOP REW FF REPEAT HELP FUNCTION TEMPO TRANSPOSE TAP TEMPO RESET RESET STYLE BREAK INTRO ENDING / rit. MAIN A OTS LINK B C D DIGITAL STUDIO SOUND CREATOR MAX AUTO FILLIN A F VARIATION HARMONY / ECHO MONO LEFT HOLD ORGAN & ACCORDION PERCUSSION GUITAR BASS STRINGS CHOIR & PAD SYNTH. XG VOICE PART ON / OFF B G LAYER C H LEFT D I BRASS WOODWIND USER ENTER SYNC.START NEW SONG ACMP DSP E.PIANO VOICE PIANO & HARPSI. GUIDE FADE IN / OUT MIN VOICE EFFECT REVERB NEXT DEMO REC MASTER VOLUME SYNC.STOP SYNC.START START / STOP DIGITAL RECORDING MIXING CONSOLE ONE TOUCH SETTING MUSIC FINDER 1 2 3 4 J E DATA ENTRY BALANCE PIANO REGISTRATION MEMORY FREEZE 1 2 3 4 5 6 7 8 MEMORY PART CHANNEL ON / OFF PART DIRECT ACCESS 1 2 3 4 5 6 7 8 EXIT Press one of the effect buttons to turn the corresponding effects on. Press it again to turn the effect off. For explanations on each of the effects, see below. ■ REVERB Reverb is an effect that recreates the acoustic ambiance of a performance space — anything from a small jazz club to a concert hall. ■ DSP The CVP-205/203 features a variety of dynamic built-in digital effects, letting you process the sound in various ways. You can use DSP to enhance the voices in subtle ways — such as by applying chorus to add animation and depth, or using a symphonic effect to give the sound warmth and richness. DSP also has effects such as distortion that can completely change the character of the sound. DSP is set for the currently selected part (MAIN/LAYER/LEFT). The DSP and VARIATION effect types and the their depth can be selected and adjusted in the MIXING CONSOLE display (page 122). ■ VARIATION (Regular voice only; page 89) This control changes the Variation effect settings, letting you alter some aspect of the effect, depending on the selected type. For example, when the Rotary Speaker effect is selected (page 122), this lets you switch the rotor speed between slow and fast. 58 CVP-205/203 Voices ■ HARMONY/ECHO This control adds Harmony or Echo effects to the voices played on the right hand section of the keyboard (page 135). The Portamento effect creates a smooth pitch glide between successively played notes. ■ MONO This control determines whether the voice is played monophonically (only one note at a time) or polyphonically for each part (MAIN/LAYER/LEFT). This is set to MONO when the lamp is lit, and set to polyphonic when the lamp is off. When set to MONO, only the last note played will sound. This lets you play wind instrument voices more realistically. Depending on the selected voice, the MONO setting also lets you effectively use the Portamento effect, when playing in legato. ■ LEFT HOLD This function causes the left part voice to be held even when the keys are released — the same effect as when the damper (sustain) pedal is pressed. This function is especially effective when used with the auto accompaniment. For example, if you play and release a chord in the auto accompaniment section of the keyboard (with the left part on and the Left voice set to Strings), the strings part sustains, adding a natural richness to the overall accompaniment sound. You can add special emphasis to melody lines you play over chords by using the Layer function with a monophonic voice. Set the Main voice to play polyphonically and set the Layer voice to play monophonically (MONO). In this case, the melody you play — including the top notes of any chords — sounds monophonically. Try this using the following voices. MAIN voice: Brass Section (polyphonic) + LAYER voice: Sweet Trump (monophonic) Using the Pedals The CVP-205/203 features three pedals. Left Pedal Damper Pedal Sostenuto Pedal You can also assign one of many other functions to these pedals (as well as the optional foot controller or footswitch). For example, you can use it to start/stop the accompaniment style, or use it to play Fill-ins (page 131). ■ Damper Pedal (Right) The damper pedal performs the same function as the damper pedal on an actual acoustic piano, letting you sustain the sound of the voices even after releasing the keys. When you press the damper pedal here, the notes you play before you release the pedal have a longer sustain. • Some voices may sound continuously or have a long decay after the notes have been released while the damper pedal is held. • Certain voices in the [PERCUSSION] and [XG] groups may not be affected by use of the damper pedal. ■ Sostenuto Pedal (Center) If you play a note or chord on the keyboard and press the sostenuto pedal while the note(s) are held, those notes will be sustained as long as the pedal is held, but all subsequently played notes will not be sustained. When you press the sostenuto pedal here while holding the note, the note will sustain as long as you hold the pedal. • Certain voices, such as [STRINGS] or [BRASS], sustain continuously when the sostenuto pedal is pressed. • Certain voices in the [PERCUSSION] and [XG] groups may not be affected by use of the sostenuto pedal. ■ Left Pedal When the Piano voice is selected, pressing this pedal reduces the volume and slightly changes the timbre of the notes you play. The settings assigned to this pedal may differ depending on the selected voice. The depth of the left pedal effect can be adjusted (page 131). ■ Foot Controller/Footswitch An optional Yamaha foot controller (FC7) or footswitch (FC4 or FC5) can be connected to the AUX PEDAL jack and used to control various functions assigned in the FUNCTION page (page 131). CVP-205/203 59 Styles The CVP-205/203 features styles (accompaniment patterns) in a variety of different musical genres including pops, jazz, Latin and dance. To use it, all you have to do is play the chords with your left hand as you perform and the selected Accompaniment Style (style) matching your music will automatically play along, instantly following the chords you play. Try selecting some of the different styles (refer to separate Data List (Style List) ) and play them. METRONOME POWER ON OFF START STOP SONG EXTRA TRACKS (STYLE) TRACK 2 (L) LCD CONTRAST TRACK 1 (R) BACK MENU TOP START / STOP REW FF REPEAT HELP FUNCTION TEMPO TRANSPOSE TAP TEMPO RESET RESET STYLE BREAK INTRO ENDING / rit. MAIN A B C DIGITAL STUDIO SOUND CREATOR MAX AUTO FILLIN A F VARIATION HARMONY / ECHO MONO LEFT HOLD ORGAN & ACCORDION PERCUSSION GUITAR BASS STRINGS CHOIR & PAD SYNTH. XG VOICE PART ON / OFF B G LAYER C H LEFT D I WOODWIND BRASS USER ENTER SYNC.START NEW SONG ACMP DSP E.PIANO VOICE PIANO & HARPSI. GUIDE FADE IN / OUT MIN VOICE EFFECT REVERB NEXT DEMO REC MASTER VOLUME SYNC.STOP SYNC.START START / STOP D DIGITAL RECORDING MIXING CONSOLE ONE TOUCH SETTING MUSIC FINDER 1 2 3 4 J E DATA ENTRY BALANCE PIANO REGISTRATION MEMORY FREEZE 1 2 3 4 5 6 7 8 MEMORY PART CHANNEL OTS LINK ON / OFF PART DIRECT ACCESS 1 2 3 4 5 6 7 8 EXIT STYLE ACMP AUTO FILLIN BREAK INTRO ENDING / rit. MAIN A B C SYNC.STOP SYNC.START START / STOP D OTS LINK Playing a style 1 2 To call up the [MAIN] display, first press the [DIRECT ACCESS] button, then press the [EXIT] button. BACK NEXT 2-1 2-2 Select a location (Preset, User, Floppy Disk) for saving the style. Select a Style. When you've opened a lower directory's display, this button (UP) lets you call up the next higher directory, from which you can select Style groups. For a list of the available accompaniment styles, refer to the separate Data List (Style List). 60 CVP-205/203 Styles 3 When the [ACMP] button is set to on, you can play/indicate chords from the auto accompaniment section of the keyboard. (Depending on the settings, this may be the range of the Left voice, or the entire keyboard.) You can set the key range for auto accompaniment (page 130). STYLE ACMP AUTO FILLIN BREAK INTRO ENDING / rit. MAIN A B C SYNC.STOP SYNC.START START / STOP D OTS LINK 4 Turn SYNC. (SYNCHRONIZED) START on. STYLE ACMP AUTO FILLIN BREAK INTRO ENDING / rit. MAIN A B C SYNC.STOP SYNC.START START / STOP Sync. Start Enabling this lets you start the style simply by playing the keyboard. D OTS LINK 5 As soon as you play a chord with the auto accompaniment section, the style starts. For details about chord fingerings, refer to page 63. Split point The Tempo can be adjusted using the TEMPO [ ][ ] or [TAP TEMPO] button. If you tap the [TAP TEMPO] button, the tempo will adjust to the same speed that you tapped. Auto Accompaniment section 6 Stop the style. END STYLE SYNC.STOP SYNC.START START / STOP ACMP Turn ACMP off. • You can begin the rhythm channels (tracks) of the Style by pressing the [START/STOP] button. • The rhythm channels of the style can also be started by tapping the [TAP TEMPO] button. With the style stopped, tap the [TAP TEMPO] button three, four or five times (three for 3/4 time, four for 2/4 or 4/4 time, five for 5/4 time). When you simultaneously play back accompaniment styles with a song, the accompaniment parts recorded to the song (channels 9 - 16) are temporarily replaced by the selected accompaniment style — letting you try out and use different accompaniment with the song (page 76). Accompaniment Style Characteristics The defining characteristics of some of the accompaniment styles are indicated above the relevant style names in the Open/Save display. Session! These styles provide even greater realism and authentic backing by mixing in original chord types and changes, as well as special riffs with chord changes, with the Main sections. These have been programmed to add “spice” and a professional touch to your performances of certain songs and in certain genres. As a result, the styles may not necessarily be appropriate — or even harmonically correct — for all songs and for all chord playing. In some cases for example, playing a simple major triad may result in a seventh chord, or playing an onbass chord may result in incorrect or unexpected accompaniment. Piano Combo! These accompaniment styles feature a basic piano trio (piano, bass, and drums), augmented in some cases with other instruments. Since this is a small combo sound, the accompaniment backing is appropriately sparse, making it useful and effective for a wide variety of songs. Pianist! These special styles provide piano-only accompaniment — effectively recreating the left-hand performance of an accomplished pianist. Just by playing the proper chords with your left hand, you can automatically add complicated arpeggios and bass/chord patterns — such as difficult-to-play stride piano parts. CVP-205/203 61 Styles Playing a Style’s Rhythm Channels only 1 The Rhythm channels are part of the styles. Each style has different rhythm patterns. Select a style (page 60). 2 You can also start the rhythm simply by playing a key on the keyboard, if Sync Start is enabled (turn on the [SYNC.START] button). Rhythm starts. STYLE ACMP AUTO FILLIN BREAK INTRO ENDING / rit. MAIN A B C SYNC.STOP SYNC.START START / STOP D OTS LINK Set to off. 3 Play along with the rhythm playback. The Tempo can be adjusted using the TEMPO [ ][ ] or [TAP TEMPO] buttons. If you tap the [TAP TEMPO] button, the tempo will adjust to the same speed that you tapped. END When selecting the style group “PIANIST,” the rhythm doesn’t sound. When you want to use any of the styles, always make sure that ACMP is turned on. Press the STYLE [START/STOP] button again to stop the rhythm playback. Adjusting the Volume Balance/Channel Muting BALANCE display MIC part Call up the BALANCE display. STYLE part (Auto Accompaniment section) SONG part Parts played from the keyboard (MAIN/LAYER/ LEFT) Adjust the output level of the Part. BALANCE CHANNEL ON / OFF CHANNEL ON/OFF display PART Call up the Channel ON/ OFF display. Call up the STYLE display by pressing the [CHANNEL ON/OFF] button, then turn the instrument you want to cancel off. To listen to only one instrument by itself, hold down the appropriate button for the channel to set the channel to SOLO. To cancel SOLO, simply press the appropriate channel button again. 62 CVP-205/203 Channel Refers to the MIDI channel in the song data (page 150). The channels are assigned as shown below. Song 1 - 16 Accompaniment Style 9 - 16 Styles Chord Fingerings The style playback can be controlled by the chords you play in the keys to the left of the split point. There are 7 types of fingerings as described below. Go to the CHORD FINGERING page (page 131), and select the Chord Fingerings. The page shows how to play chords with your left hand. SINGLE FINGER Single Finger accompaniment makes it simple to produce beautifully orchestrated accompaniment using major, seventh, minor and minor-seventh chords by pressing a minimum number of keys on the auto accompaniment section of the keyboard. The abbreviated chord fingerings described below are used. For a major chord, press the root key only. For a minor chord, simultaneously press the root key and a black key to its left. For a seventh chord, simultaneously press the root key and a white key to its left. For a minor-seventh chord, simultaneously press the root key and both a white and black key to its left. MULTI FINGER The Multi Finger mode automatically detects Single Finger or Fingered chord fingerings, so you can use either type of fingering without having to switch fingering modes. If you want to play minor, seventh, or minor-seventh chords using the SINGLE FINGER operation in the MULTI FINGER Mode, always press the closest white/black key(s) to the root of the chord. FINGERED This mode lets you produce accompaniment by playing full chords on the auto accompaniment section of the keyboard. The Fingered mode recognizes the various chord types listed on the next page. Chord detection in the AI Full Keyboard mode occurs at approximately 8th-note intervals. Extremely short chords — less than an 8th note in length — may not be detected. FULL KEYBOARD This method detects chords in the entire key range. Chords are detected in a way similar to Fingered, even if you split the notes between your left and right hands — for example, playing a bass note with your left hand and a chord with your right, or by playing a chord with your left hand and a melody note with your right. In Full Keyboard mode, chords are detected based on the lowest and second lowest notes you play. If the two lowest notes fall within a single octave, those two notes determine the chord. If the lowest note and the second lowest note are separated by more than one octave, the lowest note becomes the bass and the chord is determined from the second lowest note and the other notes played in the same octave. AI FINGERED This mode is basically the same as FINGERED, with the exception that less than three notes can be played to indicate the chords (based on the previously played chord, etc.). AI FINGERED ON BASS This mode accepts the same fingerings as the FINGERED mode, but the lowest note played in the auto accompaniment section of the keyboard is used as the bass note, allowing you to play “on bass” chords. For example, to indicate a C-on-E chord, play a C major chord with E as the lowest note (E, G, C). Artificial Intelligence AI FULL KEYBOARD When this advanced auto accompaniment mode is engaged, the CVP-205/203 will automatically create appropriate accompaniment while you play just about anything, anywhere on the keyboard using both hands. You don’t have to worry about specifying the accompaniment chords. Although the AI Full Keyboard mode is designed to work with many songs, some arrangements may not be suitable for use with this feature. This mode is similarto FULL KEYBOARD, with the exception that less than three notes can be played to indicate the chords (based on the previously played chord, etc.). 9th and 11th chords cannot be played. CVP-205/203 63 Styles Chord Types Recognized in the Fingered Mode (Example for “C” chords) CmM7 CmM7 9 ( ) ( ( C5 CM7 5 Cm7 9 Cm7 11 ) CM7aug 11 ( Caug CM7 ) Csus4 CM7 9 CM7 ) C6 ) C9 ( C6 9 C Cm9 Cm6 Cm7 Cm7 5 CmM7 5 Cdim Cdim7 C7 C7 13 C7 9 C7 5 C7aug C7sus4 Normal Voicing Display for root “C” Major [M] 1-3-5 C Ninth [9] 1-2-3-5 C9 Sixth [6] 1 - (3) - 5 - 6 C6 Sixth ninth [69] 1 - 2 - 3 - (5) - 6 or 3 - 6 - 2* C69 1 - 3 - (5) - 7 CM7 Major seventh [M7] Major seventh ninth Major seventh add sharp eleventh [M7 Flatted fifth [ 5] 11 Major seventh flatted fifth [M7 5] Suspended fourth [sus4] Augmented [aug] Major seventh augmented [M7aug] Minor [m] ] 1 - 2 - 3 - (5)j - 7 CM79 1 - (2) - 3 - 4 - 5 - 7 or 1 - 2 - 3 - 4 - (5) - 7 CM7 11 1 - 3 - 5 C 5 1-3- 5-7 CM7 5 1-4-5 1-3- 5 1 - (3) - 5 - 7 1- 3-5 1 - 2 - 3 - 5 1 - 3 - 5 - 6 Minor ninth [m9] Minor sixth [m6] Minor seventh [m7] Minor seventh ninth [m79] Minor seventh eleventh [m711] Minor major seventh [mM7] Minor major seventh ninth [mM79] Minor seventh flatted fifth [m7 5] Minor major seventh flatted fifth [mM7 5] Diminished [dim] Diminished seventh [dim7] Seventh [7] Seventh flatted ninth [7 9] 1 - 3 - (5) - 7 1 - 2 - 3 - (5) - 7 or 3 - 7 - 2 1 - (2) - 3 - 4 - 5 - ( 7) 1 - 3 - (5) - 7 1 - 2 - 3 - (5) - 7 1 - 3 - 5 - 7 1 - 3 - 5 - 7 1 - 3 - 5 1 - 3 - 5 - 6 1 - 3 - (5) - 7 or 1 - (3) - 5 - 7 1 - 2 - 3 - (5) - 7 Csus4 Caug CM7aug Cm Cm9 Cm6 Cm7 Cm79 Cm711 CmM7 CmM79 Cm7 5 CmM7 5 Cdim Cdim7 C7 Seventh suspended fourth [7sus4] C7 9 1-3-5- 6- 7 C7 13 1 - 2 - 3 - (5) - 7 or 3 - 7 - 2* C79 1 - (2) - 3 - 4 - 5 - 7 or 1 - 2 - 3 - 4 - (5) - 7 C7 11 13 1 - 3 - (5) - 6 - 7 or 3 - 6 - 7 C7 1 - 2 - 3 - (5) - 7 C7 9 1 - 3 - 5 - 7 C7 5 1-3- 5- 7 C7aug 1-4-5- 7 C7sus4 Suspended second [sus2] 1-2-5 Seventh add flatted thirteenth [7 13] Seventh ninth [79] Seventh add sharp eleventh [7 11] Seventh add thirteenth [713] Seventh sharp ninth [7 9] Seventh flatted fifth [7 5] Seventh augmented [7aug] CVP-205/203 ) • Notes in parentheses can be omitted. • For FINGERED, FINGERED ON BASS, and AI FINGERED, if you play any three adjacent keys (including black keys), the chord sound will be canceled and only the rhythm instruments will continue playing (Chord Cancel function). This let you play back only the rhythm. • Playing two same root keys in the adjacent octaves produces accompaniment based only on the root. • A perfect fifth (1 + 5) produces accompaniment based on the root and the fifth. • The auto accompaniment Style will sometimes not change when related chords are played in sequence (e.g. some minor chords followed by the minor seventh). • You can also have the CVP-205/203 “teach” you how to play Fingered chords. From the CHORD FINGERING display (page 131), specify the chord you want to learn, and the notes you should press are indicated in the display. Csus2 * Only this voicing (inversion) is recognized. Other chords not marked with an asterisk can be played in any inversion. 64 ( ) ( ) ( ( ) ( ) ) ( Chord Name [Abbreviation] [M79] Csus2 ( ) 11 ( C7 C7 13 C7 9 ) ) ( ) ( C7 9 ( ( ) ) ( ) Cm Styles Arranging the Style Pattern (SECTIONS: MAIN A/B/C/D, INTRO, ENDING, BREAK) The CVP-205/203 features various types of Auto Accompaniment Sections that allow you to vary the arrangement of the Style. They are: Intro, Main, Break and Ending. By switching among them as you play, you can easily produce the dynamic elements of a professional-sounding arrangement in your performance. 1 Select a style (page 60). 2 STYLE ACMP AUTO FILLIN INTRO BREAK ENDING / rit. MAIN A B C SYNC.STOP SYNC.START START / STOP D OTS LINK 2-1 2-3 Turn the ACMP function on. 2-2 3 Turn the SYNC. START function on. Press the [INTRO] button. To cancel the INTRO section before starting the style, press the [INTRO] button again. The Intro section starts as soon as you play a key in the Auto Accompaniment section of the keyboard, and changes to the Main section. Split point Auto Accompaniment section 4 Main sections can be shifted. STYLE ACMP AUTO FILLIN BREAK INTRO ENDING / rit. MAIN A B C OTS LINK Press this button to add breaks. D SYNC.STOP SYNC.START START / STOP You can also use this function to play only rhythms (page 62). • If you press the [INTRO] button, you can play back an Intro section while an accompaniment is playing. • Section button indications — [BREAK], [INTRO], [MAIN], [ENDING] buttons LED is green — The section is not selected. LED is red — The section is currently selected. LED is off — No section data; the section cannot be played. • You can dynamically control the level of the accompaniment by how softly or strongly you play the keys in the Auto Accompaniment section of the keyboard (page 130). • If you press the [SYNC. START] button while an accompaniment is playing, the accompaniment will stop and the CVP205/203 will enter Synchronized Start standby status. • You can also change style sections by using the pedal (page 131). • The Break section lets you add dynamic variations and breaks in the rhythm of the accompaniment, to make your performance sound even more professional. If you press the [BREAK] button while an accompaniment is playing, the fill-in will play back for one measure. • The indicator of the destination section (MAIN A/ B/C/D) will flash while the Break is playing. • When the [AUTO FILLIN] button is set to on and the MAIN [A][B][C][D] button is pressed after the final half beat (eighth note) of the measure, the fill-in will begin from the next measure. CVP-205/203 65 Styles This switches to the ending section. When the ending is finished, the Style stops automatically. You can have the ending gradually slow down (ritardando) by pressing the same [ENDING/rit.] button again while the ending is playing back. END STYLE ACMP AUTO FILLIN BREAK INTRO ENDING / rit. MAIN A B C SYNC.STOP SYNC.START START / STOP D OTS LINK Fade-in/Fade-out The accompaniment style also include a convenient Fade-in/Fade-out function that gradually fades in and fades out the accompaniment. To start the style with a fade-in, press the [FADE IN/OUT] button, then turn SYNC. START on. To cancel the fade-in before starting the style, press the button again. To fade out and stop the Style, press this button while the style is playing. The time of the fade-in/fade-out can also be set (page 140). Stopping the Style Playback While Releasing Keys (SYNC. STOP) When the Synchro Stop function is engaged, accompaniment playback will stop completely when all keys in the Auto Accompaniment section of the keyboard are released. Accompaniment playback will start again as soon as the key in the Auto Accompaniment section is played. 1 Turn ACMP (Accompaniment) on. 2 Turn SYNC. STOP on. SYNC. START is also automatically set to on when SYNC. STOP is turned on. STYLE ACMP AUTO FILLIN BREAK INTRO ENDING / rit. MAIN A B C SYNC.STOP SYNC.START START / STOP D • Styles can also be started by pressing the STYLE [START/STOP] button. • You can select the Intro and Ending type by pressing the [E] button in the MAIN window (page 67). • If you press the [INTRO] button while the ending is playing, the Intro section will begin playing after the ending is finished. • When the [AUTO FILLIN] button is set to on and you press a MAIN button while the ending is playing, fill-in accompaniment will immediately start playing, continuing with the Main section. • You can begin the accompaniment by using the Ending instead of the Intro section. In this case, the auto accompaniment doesn’t stop when the ending is finished. • If you select a different style while the style is not playing, the “default” tempo for that style is also selected. If the accompaniment is playing, the same tempo is maintained even if you select a different style. • When STOP ACMP is set to on and the accompaniment is not playing, you can play both chords and bass in the Auto Accompaniment section in the keyboard (page 130). OTS LINK 3 As soon as you play a chord with your left hand, the auto accompaniment starts. Split point You can also use the SYNC. STOP function by pressing the auto accompaniment section/left-hand range briefly (page 130). Auto Accompaniment section 66 4 The auto accompaniment stops when you release your left hand from the keys. 5 Playing a chord with your left hand automatically restarts the auto accompaniment. CVP-205/203 END Press the [SYNC. STOP]/ [SYNC. START] button again to stop the accompaniment. Synchro Stop cannot be set to on when the fingering mode is set to Full Keyboard/AI Keyboard or the auto accompaniment on the panel is set to off. Styles Selecting Intro and Ending Types (INTRO/ENDING) 1 To call up the [MAIN] display, first press the [DIRECT ACCESS] button, then press the [EXIT] button. 2 3 D E Select a Intro Play the style using the Intro or Ending section (page 30, 31). Select a Ending Playing Fill-in patterns automatically when changing accompaniment sections — Auto Fill In 1 Fill A short phrase used to add variation to the style. STYLE ACMP AUTO FILLIN BREAK INTRO ENDING / rit. MAIN A B C SYNC.STOP SYNC.START START / STOP D OTS LINK 2 Play the style and switch among the accompaniment sections as they play (page 30, 31). Fill-in patterns play automatically between each change in the Main sections. END To cancel the Auto Fill, press the [AUTO FILLIN] button again. You can also add a fill-in by pressing the selected MAIN button again. You can temporarily disable Auto Fill In during a performance by pressing the next Main section’s button twice quickly. CVP-205/203 67 Styles Appropriate Panel Setting for the Selected Style (ONE TOUCH SETTING) The convenient One Touch Setting function makes it easy for you to select voices and effects that are appropriate to the style you’re playing. Each preset style has four pre-programmed panel setups that you can select by pressing a single button. METRONOME POWER ON OFF START STOP SONG EXTRA TRACKS (STYLE) TRACK 2 (L) LCD CONTRAST TRACK 1 (R) BACK MENU TOP START / STOP REW FF REPEAT HELP FUNCTION TEMPO DIGITAL STUDIO TRANSPOSE TAP TEMPO MAX RESET RESET STYLE AUTO FILLIN BREAK INTRO ENDING / rit. MAIN A VARIATION HARMONY / ECHO MONO LEFT HOLD ORGAN & ACCORDION PERCUSSION GUITAR BASS STRINGS CHOIR & PAD SYNTH. XG VOICE PART A F B G LAYER C H LEFT ON / OFF BRASS WOODWIND USER ENTER SYNC.START NEW SONG FADE IN / OUT ACMP DSP E.PIANO VOICE PIANO & HARPSI. GUIDE MASTER VOLUME MIN VOICE EFFECT REVERB NEXT DEMO REC B C SOUND CREATOR D I DIGITAL RECORDING E J MIXING CONSOLE SYNC.STOP SYNC.START START / STOP D ONE TOUCH SETTING MUSIC FINDER 1 DATA ENTRY BALANCE PIANO 2 3 4 REGISTRATION MEMORY FREEZE 1 2 3 4 5 6 7 8 MEMORY PART CHANNEL OTS LINK ON / OFF PART 1 DIRECT ACCESS 2 3 4 5 6 7 8 EXIT ONE TOUCH SETTING 1 1 2 3 4 Select a style (page 60). 2 Press one of the ONE TOUCH SETTING buttons ([1] - [4]). LED is red — The One Touch Setting is currently selected. 3 ONE TOUCH SETTING 1 2 3 As soon as you play a chord with your left hand, the auto accompaniment starts. 4 Split point LED is green — The One Touch Setting is not selected. LED is off — No One Touch Setting data. The button is not available. Various settings (such as voices, effects, etc.) that match the selected style can be instantly recalled. When the style is not playing, Auto Accompaniment and Sync. Start will automatically be turned on. For details about the One Touch Setting parameters, refer to the separate Data List (Parameter Chart). 4 Auto Accompaniment section Stop the Auto Accompaniment. STYLE ACMP AUTO FILLIN BREAK INTRO ENDING / rit. MAIN A B C SYNC.STOP SYNC.START START / STOP D OTS LINK 5 Try out other One Touch Setting setups. You can also create your own One Touch Setting setups (page 69). ONE TOUCH SETTING 1 68 CVP-205/203 2 3 4 Styles Automatically Changing One Touch Settings with the Sections — OTS Link The convenient OTS (One Touch Setting) Link function lets you automatically have One Touch Settings change when you select a different Main section (A - D). 1 2 AUTO FILLIN OTS LINK END When you switch among the Main sections (A - D), the corresponding One Touch Setting will be called up automatically. The Main sections A, B, C, and D correspond to One Touch Settings 1, 2, 3, and 4, respectively. The One Touch Settings can be set to change with the sections in one of two different timings (page 130): • Immediately when you press a section button. • At the next measure (in an accompaniment style), after you press a section button. To cancel the OTS Link function, press the [OTS LINK] button again. Registering the Panel Controls in One Touch Setting (ONE TOUCH SETTING) This section covers how to create your own One Touch Setting setups (four setups per style). For a list of One Touch Setting setup parameters, refer to the separate Data List (Parameter Chart). 2 1 Select a style. 4 Press one of the ONE TOUCH SETTING buttons:[1] through [4]. Set up the panel controls such as selecting a voice as required. 3 Press the [MEMORY] button. MEMORY ONE TOUCH SETTING 1 2 3 4 The items you can register in a One Touch Setting are Voice, Harmony and Pedal settings. E A message prompting you to save the current style will appear. Select “YES” ND to call up the STYLE display, then save the panel settings (page 39, 45). Unless you store the panel settings here, the registered settings will be deleted when you select a different accompaniment style. CVP-205/203 69 Styles Calling Up Ideal Setups for Your Music — Music Finder The Music Finder feature lets you instantly call up the appropriate settings for the instrument — including voice, style, and One Touch Settings — simply by selecting the desired song title. If you want to play a certain song but don’t know which style and voice settings would be appropriate, the convenient Music Finder function will help you out. The recommended settings, which together make up a “record,” can also be edited and stored. This lets you create and save your own Music Finder records for future recall. METRONOME POWER ON OFF START STOP SONG EXTRA TRACKS (STYLE) TRACK 2 (L) LCD CONTRAST TRACK 1 (R) BACK MENU TOP START / STOP REW FF REPEAT HELP FUNCTION TEMPO TRANSPOSE TAP TEMPO RESET RESET STYLE BREAK INTRO ENDING / rit. MAIN A B C DIGITAL STUDIO SOUND CREATOR MAX AUTO FILLIN A F SYNC.STOP SYNC.START START / STOP D OTS LINK HARMONY / ECHO MONO LEFT HOLD PERCUSSION GUITAR BASS STRINGS CHOIR & PAD SYNTH. XG ON / OFF B G LAYER C H LEFT D I BRASS WOODWIND USER ENTER DIGITAL RECORDING MIXING CONSOLE 1 2 3 4 J E DATA ENTRY BALANCE PIANO PART CHANNEL ON / OFF DIRECT ACCESS ONE TOUCH SETTING MUSIC FINDER PART 1 2 3 4 5 6 7 8 EXIT MUSIC FINDER REGISTRATION MEMORY FREEZE 1 2 3 4 5 6 7 8 MEMORY Keep in mind that Music Finder is a performance aid in that it automatically finds appropriate accompaniment styles and voices for your playing. Even though you can specify song titles, it does not actually contain song data. MUSIC FINDER 1 2 VARIATION ORGAN & ACCORDION VOICE PART SYNC.START NEW SONG ACMP DSP E.PIANO VOICE PIANO & HARPSI. GUIDE FADE IN / OUT MIN VOICE EFFECT REVERB NEXT DEMO REC MASTER VOLUME The MUSIC FINDER records and its contents is just one example of the recommended panel setups. You can also create your own Music Finder settings for your favorite songs and genres. Select a record. For example, select the top record by pressing the [1▲▼] button to call up the recommended setups. The setting data shown here is referred to as a “record.” All .......................... Show all records. FAVORITE.............. Show the records that have added to the “Favorite” page. SEARCH1,2........... Show the results by SEARCH function (page 71). Sorting the records MUSIC ...... The record is sorted by song title. STYLE....... The record is sorted by style name. BEAT ........ The record is sorted by beat. TEMPO ..... The record is sorted by tempo. Change the order of the records (ascending or descending). Show the number of records of each page. Add the selected record to “Favorite (Bookmark)” page When you press the [H] button, the “Add selected data to the favorite list? YES/NO” message will be displayed. Select [YES] to add the selected page to “FAVORITE” page. Search record(s). Enter the condition of the search in the MUSIC FINDER SEARCH display (page 71). The results of SEARCH 1 or 2 appear in the “SEARCH 1” or “SEARCH 2” page respectively. Call up the MUSIC FINDER RECORD EDIT (page 72) display (for editing the selected record). Select a record by song title. When sorting records by song title, use the [1▲▼] button to skip up or down through the songs alphabetically. Simultaneously press the [▲▼] buttons to move the cursor to the first record. 3 70 Play the style (page 61). CVP-205/203 Turn TEMPO LOCK on/off. TEMPO LOCK function lets you avoid changing the Tempo during style playback when selecting another record. The on/off setting affects all pages (ALL/FAVORITE/SEARCH 1/SEARCH 2). Select a record by style name. When sorting the records by style name, press these buttons to move the cursor to the next /previous style. Simultaneously press the [▲▼] buttons to move the cursor to the first record. Records can be selected by using the [DATA ENTRY] dial and pressing the [ENTER] button. Styles Searching the Ideal Setups — Music Finder Search You can search the record by music title or keywords. The results appears in the display. 1 Press the [I] (SEARCH 1) button or [J] (SEARCH 2) button in the MUSIC FINDER display. 2 Enter the conditions for the search (see below), then start search by using [START SEARCH] button. Start searching the record. The results that satisfy all the conditions appear in the SEARCH page. For details about the search settings in this display, see below. ■ [A] MUSIC Searches by music or song title. Press this button to call up the display for inputting the song title. When you enter the song title (page 46), the search function calls up all records that contain the entered word or words. ■ [B] KEYWORD Searches by keyboard. Press this button to call up the display for inputting the keyword. When you enter the keyword (page 46), the search function calls up all records that contain the entered word or words. You can search several different keywords simultaneously by inserting a separator (comma) between each. The search function finds and displays all records that contain at least one match in the keywords. ■ [C] STYLE Searches by style name. Press this button to call up the STYLE FILE SELECT display. Press the [A] through [J] button in the display to select the desired accompaniment style. This convenient function lets you find all songs that use a certain accompaniment style. ■ [D] BEAT The STYLE FILE SELECT display can only be used to select the style name for searching; it cannot be used to call up the actual accompaniment style. Searches by beat or rhythmic feel. ■ [E] SEARCH AREA Selects a specific location for searching. You can further narrow down your search by using the SEARCH 1 and 2 selections. ■ [F]~[H] CLEAR Clears the entered item at left. ■ [1▲▼] TEMPO FROM You can also narrow your search by specifying a tempo range. This lets you set the minimum tempo for the search. Press the [▲▼] buttons simultaneously to instantly reset the tempo value to the minimum. ■ [2▲▼]TEMPO TO You can also narrow your search by specifying a tempo range. This lets you set the maximum tempo for the search. Press the [▲▼] buttons simultaneously to instantly reset the tempo value to the maximum. ■ [3▲▼]~[5▲▼] GENRE Selects the specific music genre for searching. The available range includes all genres (ANY), the preset genres, and any genres you’ve entered yourself (page 70). ■ [8▼] CANCEL Press this to cancel the operation and return to the previous display. CVP-205/203 71 Styles Editing Records — Music Finder Record Edit From this display, you can call up existing records and edit them to suit your preferences. You can even use this to create your own Music Finder records. 1 2 Press the [8 ▲▼] (RECORD EDIT) button in the MUSIC FINDER display. Change/clear the record data. You can also register new records. For details about all settings and operations, see below. You can also change/clear a preset record. To avoid changing/clearing the record, register the record as a new record after editing. All Music Finder records can be stored together as a single file (page 143). When calling up a stored file, a message appears prompting you to replace or append the records as desired. • Replace: All Music Finder records currently in the instrument are deleted and replaced with the records of the selected file. • Append: The records called up are added to the vacant record numbers. ■ [A] MUSIC Selects the music or song title for editing. Press the button to call up the display for inputting the music or song title, then edit the name as desired. ■ [B] KEYWORD Selects the keyword for editing. Press the button to call up the display for inputting the keyword, then edit it as desired. You can enter several different keywords by inserting a separator (comma) between each. ■ [C] STYLE Selects the style name for editing. Always enter the name when a new record is registered. Press the button to call up the STYLE FILE SELECT display. Press the [A] through [J] button in the display to select the desired style you want to change/clear/register. ■ [D] BEAT Selects the beat (time signature) for editing. When another file is selected by pressing the [C] button, the current beat setting is replaced with the beat setting of the selected file. ■ [E] FAVORITE Adds the selected record to the FAVORITE page (page 70). ■ [F]~[H] CLEAR The STYLE FILE SELECT display can only be used to select the style name for record editing; it cannot be used to call up the actual accompaniment style. Keep in mind that the Beat setting made here is only for the Music Finder search function; this does not affect the actual Beat setting of the accompaniment style itself. Clears the entered item at left. ■ [I] DELETE RECORD Clears the selected record. The deleted record number becomes empty. When you press this button, a message appears prompting you to execute, abort or cancel the operation. YES .................. Press this to clear the record and close the display. NO .................. Press this to close the display without clearing the record. CANCEL........... Press this to close the message box and return to the previous display. 72 CVP-205/203 Styles ■ [J] NEW RECORD Registers a new record. The smallest available empty record number is used for registering. When you press this button, a message appears prompting you to execute, abort or cancel the operation. YES .................. Press this to register the record and close the display. NO .................. Press this to close the display without registering the record. CANCEL........... Press this to close the message box and return to the previous display. The maximum number of records is 2500, including internal records. ■ [1▼▲] TEMPO Determines the tempo for the selected style. When changing the style with the [C] button, the tempo is automatically changed to that of the changed style. ■ [3▼▲]~[5▼▲] GENRE Indicates and changes the genre to which the selected record is assigned. The available range includes all preset genres as well as any you’ve entered yourself. ■ [6▼▲] GENRE NAME For entering a genre name. Press the button to call up the display for inputting the genre name, then edit the name as desired. A maximum of 200 genre names can be stored. The genre name you input becomes effective when the current record is edited (overwritten) by pressing the [8▲] (OK) button, or when a new record is registered by pressing the [J] (NEW RECORD) button. If you exit from the MUSIC FINDER EDIT display without actually editing or registering a record, the input genre name is deleted. ■ [8▲] OK Executes all editing and changes to the record. When you press this button, a message appears prompting you to execute, abort or cancel the operation. YES .................. Press this to replace the record and close the display. NO .................. Press this to close the display without replacing the record. CANCEL........... Press this to close the message box and return to the previous display. ■ [8▼] CANCEL Press this to cancel the operation and return to the MUSIC FINDER display. To maintain the edited and registered data, make sure to save all Music Finder records as a file (page 143). If no saved, the data will be lost when another Music Finder file is called up or the factory-programmed settings are restored (page 143). CVP-205/203 73 Song Playback Here you’ll learn how to play back songs. Songs include the internal songs of the instrument, performances you’ve recorded yourself using the recording functions (page 93), and commercially available song data. You can use this highly versatile feature in a variety of ways — playing along on the keyboard with the recorded song, as well as practicing and learning new music with the Guide (page 79) and Repeat (page 78) functions. You can also display the music notation (CVP-205 only) and lyrics in the LCD. METRONOME POWER ON OFF START SONG EXTRA TRACKS (STYLE) STOP TRACK 2 (L) LCD CONTRAST TRACK 1 (R) BACK MENU REC TOP START / STOP REW FF REPEAT NEW SONG TEMPO MAX RESET BREAK INTRO SONG A B A F B G LAYER C H LEFT D I E J SOUND CREATOR DIGITAL RECORDING RESET STYLE AUTO FILLIN HARMONY / ECHO MONO LEFT HOLD PERCUSSION GUITAR BASS WOODWIND STRINGS CHOIR & PAD SYNTH. XG VOICE PART HELP FUNCTION DIGITAL STUDIO TRANSPOSE TAP TEMPO MIN VARIATION ORGAN & ACCORDION PIANO & HARPSI. ON / OFF BRASS USER ENTER SYNC.START FADE IN / OUT ACMP DSP E.PIANO VOICE GUIDE MASTER VOLUME VOICE EFFECT REVERB NEXT DEMO ENDING / rit. MAIN C SYNC.STOP SYNC.START START / STOP MIXING CONSOLE D ONE TOUCH SETTING MUSIC FINDER 1 DATA ENTRY BALANCE PIANO 2 3 4 REGISTRATION MEMORY FREEZE 1 2 3 4 5 6 7 8 MEMORY PART CHANNEL OTS LINK ON / OFF EXTRA TRACKS (STYLE) TRACK 2 (L) TRACK 1 (R) DIRECT ACCESS REC NEW SONG TOP START / STOP REW FF PART 1 2 REPEAT 3 4 5 6 7 8 EXIT GUIDE SYNC.START Compatible Song Types • Internal songs (Song Book; CVP-205 only) • Song data on included disk [50 greats for the Piano (CVP-205/203), Music Software Collection (CVP-203 only)] • Commercially available song data Commercially available music data is subject to copyright restrictions, and is intended only for your own personal use. Disks having this logo mark feature song data compatible with GM (General MIDI). Disks having this logo mark feature song data compatible with Yamaha’s XG format. XG is a significant enhancement of the “GM system level 1” standard, providing more voices, greater editing control, and support for multiple effect sections and effect types. For more information on the song file types compatible with the Clavinova, see page 151. Disks having this logo mark feature song data compatible with Yamaha’s DOC (Disk Orchestra Collection) format. Disks having this logo mark feature song data compatible with Yamaha’s original MIDI file format. • Songs you recorded (page 93) and stored to the CVP-205/203 or disk. 74 CVP-205/203 Song Playback Song Playback Playing the Internal Songs 1 BACK If the MAIN screen (at left) is not displayed, press the [DIRECT ACCESS] button followed by the [EXIT] button. n You can also make a variety of other settings (such as tempo, voice selection, settings for the practice functions, etc.) and have them automatically called up when you play back the song (page 105). 2-1 2 Select the PRESET tab with the [BACK] button. BACK You can enable the Synchro Start for the song by simultaneously pressing the [TOP] button and the SONG [START/STOP] button. The song starts as soon as you play the keyboard. You can also use this function along with the Style’s Synchro Start function (page 61). n 2-2 Open a folder and select a song to be played back. 3 The song starts. You can have the volume automatically fade in and fade out at the beginning and end of the song. Simply press the [FADEIN/OUT] button at the start of song playback to fade in the song, and press it again at the end of the song to fade out. END START / STOP REC NEW SONG TOP START / STOP REW FF REPEAT GUIDE SYNC.START Adjust the tempo by using the TEMPO [ ][ ] buttons (page 51) or the [TAP TEMPO] button. You can even change the playback speed by tapping out the tempo — simply tap the [TAP TEMPO] button twice. Songs can also be played back continuously. Set SONG CHAIN PLAY to ON from the SONG SETTING display (page 129). To stop the song immediately, press the button again. Press the EXIT button in order to go back to the previous screen. Make sure that the Language setting for the instrument (page 143) is the same as that of the file name of the song that you are playing back. CVP-205/203 75 Song Playback Simultaneously Playing a Song and an Accompaniment Style When playing back a song and an accompaniment style at the same time, channels 9 16 of the song data are replaced with accompaniment style channels — allowing you to use the auto accompaniment styles and features in place of the accompaniment parts of the song. Make the settings below and play your own chord substitutions in place of the song’s chord data. • [ACMP] button .................. ...ON • [AUTO FILL IN] button ..... ...ON 1 2 3 4 Select the song and start playback by pressing the SONG [START/STOP] button. Select the desired accompaniment style. Start the style by pressing the STYLE [START/STOP] button. While the song is playing, insert a break or change sections (with the STYLE section buttons.) Fill-in patterns play when you switch sections. END The style automatically stops when the song finishes or is stopped. Some of the internal songs have been created using the accompaniment styles. For these songs, the accompaniment styles are automatically started when starting song playback. 76 CVP-205/203 The accompaniment stops when you stop the song. If the accompaniment style is playing and you start the song, the accompaniment automatically stops. However, for internal songs that use accompaniment styles, the accompaniment style is not stopped. Song Playback Playing Back Songs on Disk Before proceeding, make sure to read the section “Handling the Floppy Disk Drive (FDD) and Floppy Disk” (page 6). Insert the disk into the drive. Insert the disk shutter side first and label face up. The method for playing back is the same as in the “Playing the Internal Songs” instructions (page 75), except that you should select FLOPPY DISK page in the SONG display. Other Playback-related Operations ■ Repeat / Rewind / Fast forward During playback, you can have the song return to the top and play back again from the beginning by pressing this button. When playback is stopped, pressing this button returns the song to the beginning. REC TOP START / STOP REW FF REPEAT SYNC.START NEW SONG Press this button to call up the SONG POSITION display (see below). To return to the SONG display, press the [EXIT] button. SONG POSITION display When “BAR” is selected, you can specify a measure number (counted from the beginning of the song) by using the [REW] and [FF] buttons. When “PHRASE MARK” is selected, specify the phrase mark number by using the [REW] and [FF] buttons. “PHRASE MARK” is shown only when the song contains phrase marks. Press the [J] button to toggle between “BAR” and “PHRASE MARK,” then use the [REW] and [FF] buttons to select the desired measure or phrase mark. n You can set whether or not the Clavinova automatically calls up the first disk song when a disk is inserted (page 142). n Some song data for the Clavinova has been recorded with special “free tempo” settings. During playback of such song data, the measure numbers shown in the display will not correspond to the actual measure; this only serves as a reference as to how much of the song has been played back. n Songs containing a large amount of data may not be able to be read properly by the instrument, and as such you may not be able to select them. The maximum capacity is about 200– 300KB, however this may differ depending on the data contents of each song. Phrase Mark This data specifies a certain location in the song data. In the included “Music Software Collection” songs (CVP-203 only), these are indicated by numbers (1, 2, etc.) in the score. ■ Adjusting the Volume Balance / Muting Specific Channels BALANCE Press this button to call up the BALANCE display (page 62). CHANNEL ON / OFF PART Press this button to call up the CHANNEL ON/OFF display (see below). CHANNEL ON/OFF display Select the [SONG] tab with the [CHANNEL ON/OFF] button, and mute the desired channel by setting it to [OFF]. To solo a channel (only that channel will sound), hold down the appropriate button corresponding to the channel. To release the solo for the channel, press that channel’s button again. Channel Refers to the MIDI channel in the song data. The channels are assigned as shown below for the CVP-205/203. Song 1 - 16 Accompaniment Style 9 - 16 CVP-205/203 77 Song Playback Muting Specific Parts — Track1/Track2/Extra Tracks This feature lets you mute certain parts of the song (Track1, Track2, Extra Tracks), and play back only those parts you want to hear. For example, if you want to practice the melody of a song, you can mute just the right-hand part and play that part yourself. 1 Select the song to be played back (page 74). You can change the channel assignments for Track 1 and Track 2 (page 129), letting you specify which parts are muted when pressing the [TRACK 1]/[TRACK 2]/ [EXTRA TRACKS] buttons. Use this button to turn on/off the additional performance parts (all but the right hand/left hand). 2 SONG EXTRA TRACKS (STYLE) TRACK 2 (L) TRACK 1 (R) Use this button to turn on/off the right-hand part. All tracks are automatically set to on when selecting a different song. Use this button to turn on/off the left-hand part. 3 Start the song. Adjust the tempo by using the TEMPO [ REC TOP NEW SONG START / STOP REW FF ][ REPEAT ] buttons (page 51). GUIDE END START / STOP To stop the song, press the button again. SYNC.START Repeat Playback of a Specific Range This feature allows you to specify a certain range of the song (between Point A and Point B), and play it back repeatedly. 1 2 Play back the song (page 75, 77). REC TOP NEW SONG 3 START / STOP REW FF REPEAT SYNC.START Press this button at the point you want the repeating phrase to start (Point A). Press this button at the point you want the repeating phrase to end (Point B). After an automatic lead-in (to help guide you into the phrase), the range from point A to point B is played back repeatedly. Regardless of whether the song is playing back or is stopped, pressing the [TOP] button returns to point A. You can also specify Points A and B when the song is stopped. Set Point A by pressing the [REPEAT] button, then use the [FF] button to move to the desired end location, then set Point B by pressing the [REPEAT] button again. Point B cannot be selected unless Point A has been selected first. n Specifying only Point A results in repeat playback between Point A and the end of the song. n 4 Stop the song. START / STOP END To cancel the Repeat function, press the button again. 78 CVP-205/203 REPEAT The specified A and B points will be erased when selecting a different song number, cancelling the Repeat function, or selecting a different repeat mode — such as Phrase Repeat or repeat in Song Chain Play (page 129). Song Playback Using the Practice Functions —Guide These fun features make it easy to learn new music. The key guide lamps indicate the notes you should play, when you should play them, and how long you should hold them down. Also, when you sing and play along with a song using a connected microphone (CVP-205 only), the Clavinova automatically adjusts the timing of the song to match your vocal performance. REC TOP NEW SONG START / STOP REW FF REPEAT You can turn the key guide lamps on/off from the SONG SETTING display (page 129). GUIDE SYNC.START Key guide lamp Practice Functions For keyboard performance ■ Follow Lights When this is selected, you can see which notes you should play by watching the key guide lamps. They light up in time with music, showing you when to play a note. You can also practice at your own pace — since the accompaniment waits for you to play the notes correctly. • Accompaniment Guide If the song data you’re using contains chord data and the [ACMP] button is turned on, you can use the guide lamps (page 129) to help you play chords as well. Watch the guide lamps and try playing the appropriate chords. ■ Any Key With this function, you can play the melody of a song simply by pressing a single key (any key is OK) in time with the rhythm. As long as you play the key in time with the music, the melody flows smoothly with the song. You can also determine the timing by which the key guide lamps light to fit your playing preference (Guide Lamp Timing; page 129). n If you want to learn how to play certain chords, use the Chord Tutor function (page 131). n The Accompaniment Guide function cannot be used if the chord fingering method is set to Single Finger, Full keyboard or AI Full Keyboard. For sing-along performance ■ Karao-Key This convenient function lets you control the song and accompaniment playback with just one finger, while you sing along. Simply play a key on the keyboard in time with the music — any key is fine — and the accompaniment parts of the song follow your playing. This lets you control the timing and tempo of the song and accompaniment to perfectly match your singing performance. CVP-205/203 79 Song Playback Practicing Music with the Guide Functions 1 Select the desired practice function from the SONG SETTING page in the FUNCTION display (page 129). For details on the SONG SETTING display, see page 129. n The guide lamps light according to song channel recorded to Tracks 1 and 2 and the chord data in the song (when such data is included). Normally, you can leave the AUTO SET CH function set to ON, and the song channel will automatically be set. If the results aren't satisfactory, you'll need to match the Channel Setting “TRK1 CH” and “TRK2 CH” parameters to the appropriate right- and left-hand parts. Selects the specific practice function. Turns the key guide lamps on/off. Determines the timing by which the key guide lamps light. JUST ..... The guide lamp lights in time with the music, at the same time you should play the appropriate notes. NEXT..... The guide lamps light slightly ahead of the music, indicating the notes you should play next. The guide lamp flashes if you do not play the key with the correct timing. Determines whether phrase mark sections in the song will be repeatedly played back or not. When this is set to ON, the specified measures of the phrase play back repeatedly. Call up the SONG POSITION display by pressing either the [REW] button or the [FF] button, and select “PHRASE MARK” by pressing the [J] button. Set the desired phrase mark number by using the [REW] and [FF] buttons. 2 Select the desired song (page 75, 77) and mute the track you wish to practice (page 78). 3 REC TOP REC REW FF REPEAT GUIDE SYNC.START NEW SONG 4 START / STOP TOP START / STOP REW FF REPEAT GUIDE SYNC.START Start the song and try playing the part you’ve muted. Adjust the tempo by using the TEMPO [ ][ ] buttons (page 51). 5 TOP NEW SONG START / STOP SYNC.START Stop the song. 80 Phrase Mark This data specifies a certain location in the song data. In the included “Music Software Collection” songs (CVP-203 only), these are indicated by numbers (1, 2, etc.) in the score. n Track 1 or Tracks 1 & 2 are automatically selected for practicing when calling the practice function — as long as you haven’t muted the track to be practiced. n The key guide lamps sometimes light an octave or two lower/higher than the actual pitch. Any notes outside of the 88-key range cannot be indicated by the key guide lamps. n NEW SONG REC n CVP-205/203 REW FF REPEAT GUIDE If the right- and left-hand parts recorded to the song data have not been properly separated, the practice functions may not work as expected. END To turn the practice function, press the button again. GUIDE Song Playback Displaying Music Notation — Score (CVP-205 only) With this feature, you can have the notation automatically shown on the display as the song plays. This can be used with your own recordings as well as the internal Demo songs. 1 Select the desired song (page 75, 77). 2 If the MAIN screen (at left) is not displayed, press the [DIRECT ACCESS] button followed by the [EXIT] button. The displayed notation is generated by the Clavinova based on the song data. As a result, it may not be exactly the same as commercially available sheet music of the same song — especially when displaying notation of complicated passages or many short notes. 3 n Enables/disables display of the left-hand key range. Depending on other settings, this parameter may be unavailable and may appear grayed out. If this is the case, go to the detailed setting display (shown below; use the [8▲▼] buttons) and set the LEFT CH. parameter to any channel except “AUTO.” Or, go to the SONG SETTING display in the Function menu (page 129) and set the TRACK 2 parameter to any channel except “OFF.” Some song data for the Clavinova has been recorded with special “free tempo” settings. For such song data, the tempo, beat, measure and music notation will not be displayed correctly. n [RIGHT] and [LEFT] cannot be turned off at the same time. Enables/disables display of the right-hand key range. Channel 1 is automatically selected when [TRACK1] is set to [OFF] from the SONG SETTING display (page 129). Enables/disables display of the lyrics. If the selected song does not contain lyric data, lyrics are not displayed. Enables/disables display of the chords. If the selected song does not contain chord data, chords are not displayed. Enables/disables display of the note name (pitch). Determines the display resolution (or zoom level) of the notation. SMALL ..... Notation is shown in small size. LARGE ..... Notation is shown in large size. This calls up the detailed setting display for notation. For details, see the next page. n The note name is indicated at the left of the note. When the space between the notes is too small, the indication may be moved to the top left of the note. n You can increase the number of measures that will be displayed by decreasing the other items to be displayed (parts, lyrics, chords, etc.). n When accidentals (sharp and flats) and notes cannot be displayed on one line, they are displayed in the next line from the middle of the measure. n The notation functions cannot be used to create song data by inputting notes. For information on creating song data, see page 97. CVP-205/203 81 Song Playback Detailed Settings for Notation When “LEFT” and “RIGHT” are set to the same channel, the notation of the right-hand notes and left-hand notes are displayed in piano format (two connected staves). ■ [1▲▼] LEFT CH/[2▲▼] RIGHT CH This determines the Left channel (channel for the left-hand part) and Right channel (channel for the right-hand part). This setting returns to AUTO when a different song is selected. AUTO .........................The channels for the right- and left-hand parts are assigned automatically — setting the parts to the same channel as the channel which is specified in the SONG SETTING display of the Function menu (page 129). 1-16 ............................Assigns the part to the specified channel, 1- 16. OFF (LEFT CH only)....No channel assignment. ■ [3▲▼], [4▲▼] KEY SIGNATURE This lets you enter key signature changes in the middle of a song, at the stopped position, allowing you to transpose key at any point within a song. For a list of the key signatures, with their relative minor keys and accidentals, see the chart below. Key Signatures and Accidentals C Maj (A min) G Maj (E min) D Maj (B min) A Maj (F min) E Maj (C min) B Maj (G min) F Maj (D min) C Maj (A min) G Maj (E min) D Maj (B min) A Maj (F min) E Maj (C min) B Maj (G min) F Maj (D min) The note indicates the root note of the major key, and the C Maj (A min) note indicates the root of the relative minor. ■ [5▲▼] QUANTIZE This gives you control over the note resolution in the notation, letting you shift or correct the timing of all displayed notes so that they line up to a particular note value. Make sure to select the smallest note value which is used in the song. Note resolution: 1/4 note, 1/8 note, 1/16 note, 1/32 note, 1/4 note triplet, 1/8 note triplet, 1/16 note triplet, 1/32 note triplet 82 CVP-205/203 Short notes and ornamented notes (such as trills and grace notes) which are shorter than the Note resolution will not be displayed in the notation. Song Playback ■ [6▲▼] NOTE NAME When [NOTE NAME] is set to ON, the note name and solfeggio name (do, re, mi, etc.) are indicated. ABC ................. Note names are indicated as letters (C, D, E, F, G, A, B). Fixed Do .......... Note names are indicated in solfeggio and differ depending on the selected language (page 50). English.............. Do Re Mi Fa Sol La Ti French .............. Ut Re Mi Fa Sol La Si Italian............... Do Re Mi Fa Sol La Si German............ Do Re Mi Fa Sol La Si Spanish............. Do re Mi Fa Sol La Si Japanese........... Movable Do..... Note names are indicated in solfeggio according to the scale intervals, and as such are relative to the key. The root note is indicated as Do. For example, in the key of G major the root note of Sol would be indicated as Do. As with “Fixed Do,” the indication differs depending on the selected language. ■ [8▲] OK This closes the detailed setting display and starts generating the notation. You can also execute this by pressing the [ENTER] button on the panel. ■ [8▼] CANCEL You can select the display pages (one before and after) by the using the [BACK]/ [NEXT] buttons or the pedal (page 131). This closes the detailed setting display without changing the settings. You can also execute this by pressing the [EXIT] button or [RECORD] button on the panel. CVP-205/203 83 Song Playback Displaying the Lyrics This function lets you display the lyrics while the song is playing back — making it easy to sing along with your performance or song playback. * Microphone input is available only on the CVP-205. 1 2 Select the desired song (page 75, 77). The language used for lyrics display depends on the particular lyric data. If the lyrics are garbled or unreadable, you can remedy this by changing the “LYRICS LANGUAGE” setting from the SONG SETTING display (page 129). 3 If the selected song does not contain lyric data, lyrics are not displayed. If the selected song contains chord data, chord names are displayed with the lyrics. 4 REC TOP NEW SONG START / STOP REW FF REPEAT GUIDE The contents of the display can also be shown on a connected TV (CVP-205 only; page 136, 145). SYNC.START Start the song. 5 The lyrics are in reverse display along with song playback. END REC NEW SONG TOP START / STOP REW FF REPEAT SYNC.START Stop the song. To return to the previous page, press the button. 84 CVP-205/203 GUIDE EXIT The lyrics can be changed (page 108). Saving and Recalling Custom Panel Setups — Registration Memory Registration Memory is a powerful feature that lets you set up the Clavinova just as you want — selecting specific voices, styles, effect settings etc. — and save your custom panel setup for future recall. Then, when you need those settings, simply press the appropriate REGISTRATION MEMORY button. METRONOME POWER ON OFF START SONG EXTRA TRACKS (STYLE) STOP TRACK 2 (L) LCD CONTRAST TRACK 1 (R) BACK MENU TOP START / STOP REW FF REPEAT REGISTRATION MEMORY MAX STYLE ACMP AUTO FILLIN 2 3 4 RESET INTRO BREAK B 5 F FUNCTION B G LAYER LEFT C C H SOUND CREATOR D I DIGITAL RECORDING E 6 RESET ENDING / rit. MAIN A A DIGITAL STUDIO TRANSPOSE TAP TEMPO MIN VARIATION HARMONY / ECHO MONO LEFT HOLD ORGAN & ACCORDION PERCUSSION GUITAR BASS STRINGS CHOIR & PAD SYNTH. XG VOICE PART HELP ON / OFF BRASS USER ENTER SYNC.START NEW SONG TEMPO 1 DSP E.PIANO WOODWIND VOICE PIANO & HARPSI. GUIDE FADE IN / OUT FREEZE VOICE EFFECT REVERB NEXT DEMO REC MASTER VOLUME MIXING CONSOLE SYNC.STOP SYNC.START START / STOP D 7 8 ONE TOUCH SETTING MUSIC FINDER 1 MEMORY 2 3 4 J DATA ENTRY BALANCE PIANO REGISTRATION MEMORY FREEZE 1 2 3 4 5 6 7 8 MEMORY PART CHANNEL OTS LINK ON / OFF PART 1 DIRECT ACCESS 2 3 4 5 6 7 8 EXIT Registering Panel Setups — Registration Memory This shows you how to register your custom panel settings to the REGISTRATION MEMORY buttons. Make all the settings you want with the panel controls, and Registration Memory will “remember” them for you. 1 Set up the panel controls as desired. For a list of the settings that can be registered, refer to the separate Data List (Parameter Chart). 2 Keep in mind that songs or styles on disk cannot registered to Registration Memory. If you want to register a disk-based song or style, copy the relevant data to “USER” in the SONG/STYLE display (page 39) and register the data separately. REGISTRATION MEMORY FREEZE 1 2 3 4 5 6 7 8 MEMORY 3 Cancels the registration and returns to the MAIN display. You can also use the [EXIT] button. Select the desired parameter groups for the settings you want to register. You can also use the [DATA ENTRY] dial to navigate in this display. To register a parameter group, checkmark the corresponding box. Groups left without checkmarks will not be included in the Registration Memory setting. This allows you to maintain certain settings, even when switching among Registration Memory presets. You can also use the Freeze function (page 87) to override the Registration Memory changes — letting you prevent certain panel settings from being changed. END Enters a checkmark to the selected box. You can also use the [ENTER] button. Removes the checkmark from the selected box. You can also use the [ENTER] button. Press the desired number button for registering the settings. REGISTRATION MEMORY FREEZE 1 2 3 4 5 6 7 8 MEMORY Indicator is green......The panel setting is registered, but not selected. Indicator is red .........The panel setting is registered and is currently selected. Indicator is off ..........The panel setting is not registered. Any data that was previously registered to the selected REGISTRATION MEMORY button (indicator is green or red) will be erased and replaced by the new settings. The registrations registered here will be lost when the power is turned off, unless you perform the Save operation explained on the next page. CVP-205/203 85 Saving and Recalling Custom Panel Setups — Registration Memory Saving Your Registration Memory Setups The settings registered to the REGISTRATION MEMORY [1]-[8] buttons are saved as a single file. BANK 01 All settings registered to buttons [1][8] are referred to as a “bank.” The banks can be saved to “USER” or “FLOPPY DISK” as Registration bank files. 1 2 Keep in mind that the size of the Registration bank files and the memory space they occupy depends on the amount of functions set in each. Press the [DIRECT ACCESS] button and [EXIT] button to call up the MAIN display. Save the settings you’ve made to the Registration Memory buttons as a single Registration bank file (page 45). The REGISTRATION EDIT display appears. For details on this display, see below. REGISTRATION EDIT display The contents of the current Registration Memory bank (REGIST.) are listed in the REGISTRATION EDIT screen. The names of the stored Registration Memory presets are shown in the display and the indicators of the relevant REGISTRATION MEMORY buttons are lit in green. From this screen, you can select, name, or delete the Registration Memory presets. Select ...............Press the [A] - [J] buttons. The REGIST. display is linked to the REGISTRATION MEMORY [1] - [8] buttons. When you select the Registration Memory preset in the display, the related button turns on (indicator is red). Name ...............This operation is the same as that in “Naming Files and Folders” (page 42) in “Basic Operations — Organizing Your Data.” Delete ..............This operation is the same as that in “Deleting Files/Folders” (page 44) in “Basic Operations — Organizing Your Data.” The result of the Name/Delete operation will be lost when the power is turned off unless you return to the REGISTRATION BANK display by pressing the [8▼] (UP) button and save the data (page 45). 86 CVP-205/203 Saving and Recalling Custom Panel Setups — Registration Memory Recalling a Registration Memory Setup You can recall all of the panel settings you’ve made — or only those you specifically want or need. For example, if you de-select “STYLE” in the REGISTRATION MEMORY display, you can keep the currently selected style even when you change the Registration Memory preset. Recalling the Registered Settings Select the desired bank in the REGISTRATION BANK display (page 86). Press the appropriate REGISTRATION MEMORY button (any whose indicators are green) to recall the desired settings. You can program your Registration Memory presets to be called up in sequence, in any order you desire. Once programmed, the presets 1 - 8 can be selected in sequence with the [BACK][NEXT] buttons or the pedal (page 134). REGISTRATION MEMORY FREEZE 1 2 3 4 5 6 7 8 MEMORY Selecting the Freeze Settings 1 2 MENU DEMO HELP FUNCTION Call up the “FREEZE” page from the REGIST.SEQUENCE/ FREEZE/VOICE SET screen (page 134). Enters a checkmark to the selected box. Select the Freeze settings. 3 Removes the checkmark from the selected box. Press the [FREEZE] button. When Freeze is active (lamp is lit), the settings you specified in the Freeze page will be maintained or left unchanged, even when changing Registration Memory presets. REGISTRATION MEMORY 1 FREEZE 4 2 3 4 5 6 7 8 MEMORY Press the appropriate REGISTRATION MEMORY button (any whose indicators are green) to recall the desired settings. REGISTRATION MEMORY FREEZE 1 2 3 4 5 6 7 8 MEMORY CVP-205/203 87 Editing Voices — Sound Creator The CVP-205/203 has a Sound Creator feature that allows you to create your own voices by editing some parameters of the existing voices. Once you’ve created a voice, you can save it as a USER voice for future recall. METRONOME POWER ON OFF START STOP SONG EXTRA TRACKS (STYLE) TRACK 2 (L) LCD CONTRAST TRACK 1 (R) BACK MENU TOP START / STOP REW FF REPEAT HELP A FUNCTION TEMPO TRANSPOSE TAP TEMPO MIN MAX RESET BREAK INTRO RESET ENDING / rit. MAIN A B C DIGITAL STUDIO SOUND CREATOR STYLE AUTO FILLIN F VARIATION HARMONY / ECHO MONO LEFT HOLD ORGAN & ACCORDION PERCUSSION GUITAR BASS STRINGS CHOIR & PAD SYNTH. XG VOICE PART ON / OFF B G LAYER C H LEFT D I BRASS USER ENTER SYNC.START NEW SONG FADE IN / OUT ACMP DSP E.PIANO WOODWIND VOICE PIANO & HARPSI. GUIDE MASTER VOLUME VOICE EFFECT REVERB NEXT DEMO REC SYNC.STOP SYNC.START START / STOP D OTS LINK DIGITAL RECORDING MIXING CONSOLE ONE TOUCH SETTING MUSIC FINDER 1 2 3 4 J E DATA ENTRY BALANCE PIANO REGISTRATION MEMORY FREEZE 1 2 3 4 5 6 7 8 MEMORY PART CHANNEL ON / OFF PART SOUND CREATOR DIRECT ACCESS 1 2 3 4 5 6 7 8 • The Voice can be edited in realtime while playing back a song/style. • Keep in mind that adjustments made to the parameters may not make much change in the actual sound depending on the original settings of the voice. EXIT Operation 1 Press the [F], [G] or [H] button to select the Part (MAIN, LAYER or LEFT) containing the voice you wish to edit. 2 Press the [SOUND CREATOR] button. DIGITAL STUDIO F SOUND CREATOR G H DIGITAL RECORDING I MIXING CONSOLE J PART 3 The voice can also be selected in the SOUND CREATOR display. CAUTION The settings are lost if the edited part’s voice is switched to another voice. Important data should be saved to User Drive or floppy disk. Edit the voice parameters. The operations for each function selected in this step are covered in detail, starting on page 90. NATURAL VOICE Select the desired menu by pressing the [NEXT]/ [BACK] button. REGULAR VOICE Select the desired menu. The selected menu is highlighted. Can be used during editing to compare the sound of the original voice with the edited voice. Indicates the parameters available for editing in this display. These correspond to the parameters/ values shown at the bottom of the display. 4 88 Save the edited voice to the USER drive (Flash ROM) as a USER voice (page 45). CVP-205/203 Opens the Save (Voice) display for saving the edited voice as a User voice (page 45). 5 Press the [USER] button to select the edited voice, and play the keyboard. Editing the voice — Sound Creator SOUND CREATOR Parameters PIANO Determines the parameters unique to piano sounds, such as tuning curve or sustain sampling. This page is available only when the Natural piano voice is selected. COMMON Determines the common settings such as voice volume or octave. SOUND Determines the timbre/EG (Envelope Generator)/vibrato of the voice (Regular voice only). EFFECT Determines the effect depth or type. HARMONY Determines the Harmony/Echo settings. The available parameters differ depending on the selected voice type, Regular or Natural (see below). Keep in mind that there are certain parameters whose Sound Creator settings affect only the Main part’s voice. The following parameters are linked to the ones in each display. Common parameter Other location MONO VOICE EFFECT (TOP PANEL) page 59 PORTAMENTO TIME MIXING CONSOLE page 121 LEFT PEDAL TYPE CONTROLLER (FUNCTION) page 131 LEFT PEDAL SETTING CONTROLLER (FUNCTION) page 131 FILTER BRIGHTNESS MIXING CONSOLE page 121 FILTER HARMONIC CONTENT MIXING CONSOLE page 121 REVERB DEPTH MIXING CONSOLE page 122 CHORUS DEPTH MIXING CONSOLE page 122 DSP ON/OFF VOICE EFFECT (TOP PANEL) page 58 DSP DEPTH MIXING CONSOLE page 122 DSP TYPE/VARIATION MIXING CONSOLE/VOICE EFFECT (TOP PANEL) page 58,122 HARMONY/ECHO TYPE HARMONY/ECHO (FUNCTION) page 135 HARMONY/ECHO VOLUME HARMONY/ECHO (FUNCTION) page 135 HARMONY/ECHO SPEED HARMONY/ECHO (FUNCTION) page 135 HARMONY/ECHO ASSIGN HARMONY/ECHO (FUNCTION) page 135 HARMONY/ECHO CHORD NOTE ONLY HARMONY/ECHO (FUNCTION) page 135 HARMONY/ECHO TOUCH LIMIT HARMONY/ECHO (FUNCTION) page 135 Natural Voices and Regular Voices Built into the CVP-205/203 are two different tone generation sources, Natural and XG. The Natural tone generation source and its voices feature a huge amount of wave memory, giving you enormous and finely detailed expressive power over the sound. The XG source (which powers the Regular voices) provide maximum compatibility with a wide variety of devices and song data. Voices sounded with the XG source are divided into two groups. One is the original set of Clavinova voices (Cool!, Sweet!, Live!), and the other is the conventional XG set. The maximum amount of polyphony for each tone generation source is set up to best enhance your performance. In general, the songs and styles are played back using the XG source, while the Natural voices are played from the keyboard — allowing you to play the Natural voices with full polyphony, even if the song and style data exceeds the polyphonic limit. Natural! Cool! Sweet! Clavinova-exclusive voices Live! XG GM/XG-compatible voices Natural voices (sounded by Natural tone generation source) Regular voices (sounded by XG tone generation source) Used mainly for keyboard-played voices For keyboard-played voices, song/style playback* * Depending on the particular style selected, a Natural voice may be used for the accompaniment. Usually, songs are played back using the XG voices (page 152); however, you can have them automatically “re-voiced” — using the exceptionally rich and realistic sounds exclusive to the CVP-205/203 (page 120). CVP-205/203 89 Editing the voice — Sound Creator PIANO (Piano Voice has been selected) The explanations here apply to step #3 on page 88. Determines the tuning curve, especially for piano voices. Select “FLAT” if you feel the tuning curve of the piano voice does not quite match that of other instruments voices. The available parameters differ depending on the selected voice. STRETCH .. Tuning curve particularly for pianos FLAT .......... Tuning curve in which the frequency is octave doubled over the entire keyboard range These controls are used to adjust the brilliance of the tone. This setting affects all Natural voices globally. When other than piano voice (Natural) is selected, set this on EFFECT page. For details, see the EFFECT page (page 92). Determines the depth of sustain sampling for the damper pedal. COMMON The explanations here apply to step #3 on page 88. The parameters are the same as for CONTROLLER display. For details, see page 131. Set the volume of the current edited voice. Determines the touch sensitivity, or how greatly the volume responds to your playing strength. 0 —–– Produces more dramatic level drops, the more softly you play. 64 —– Normal response. 127 — Produces high volume for any playing strength (fixed) Set the portamento time of each part (MAIN/LAYER/VOICE) (Regular Voice only) (page 121). This determines whether the voice is played monophonically (Regular Voice only) (page 59). Shift the octave range of the selected voice up or down in octaves. When the Main or Layer part’s voice is used, the M/LYR parameter is available; when the Left part’s voice is used, the LEFT parameter is available. SOUND (Regular Voice only) The explanations here apply to step #3 on page 88. Determines the filter, EG, and vibrato settings (see below). 90 CVP-205/203 Editing the voice — Sound Creator ■ FILTER FILTER settings determine the overall timbre of the sound by boosting or cutting a certain frequency range. • BRIGHTNESS Determines the cutoff frequency or effective frequency range of the filter (see diagram). Higher values result in a brighter sound. Volume Cutoff frequency These frequencies are “passed” by the filter. • Harmonic Content Determines the emphasis given to the cutoff frequency (resonance), set in BRIGHTNESS above (see diagram). Higher values result in a more pronounced effect. In addition to making the sound either brighter or more mellow, Filter can be used to produce electronic, synthesizer-like effects. Frequency (pitch) Cutoff range Volume Resonance Resonance Frequency (pitch) ■ EG The EG (Envelope Generator) settings determine how the level of the sound changes in time. This lets you reproduce many sound characteristics of natural acoustic instruments — such as the quick attack and decay of percussion sounds, or the long release of a sustained piano tone. • ATTACK ...... Determines how quickly the sound reaches its maximum level after the key is played. The higher the value, the slower the attack. Level • DECAY........ Determines how quickly the sound reaches its sustain level (a slightly lower level than maximum). The higher the value, the slower the decay. ATTACK DECAY Key on • RELEASE ..... Determines how quickly the sound decays to silence after the key is released. The higher the value, the slower the release. Time Key off If RELEASE is set to a large value, the sustain becomes long. ■ VIBRATO • DEPTH........ Determines the intensity of the Vibrato effect (see diagram). Higher settings result in a more pronounced Vibrato. VIBRATO Creates a wavering in the sound by periodically changing the pitch. • SPEED......... Determines the speed of the Vibrato effect (see diagram). • DELAY ........ Determines the amount of time that elapses between the playing of a key and the start of the Vibrato effect (see diagram). Higher settings increase the delay of the Vibrato onset. RELEASE SPEED Level DEPTH DELAY Time CVP-205/203 91 Editing the voice — Sound Creator EFFECT The explanations here apply to step #3 on page 88. Determines the brilliance of the tone, when a Natural voice is selected (CVP205 only). This can also be set from the PIANO page (page 90), when a piano voice is selected. • Metallic ......... Sharp metallic tone • Bright............ Bright tone • Normal .......... Standard tone • Mellow .......... Soft and mellow tone • Dark .............. Dark tone Determines the effect type (Reverb/ Chorus/DSP) for the Natural voices. When a regular voice is selected, the DSP type and Variation are set in two separate menus. For information on the effect structure, see page 124; for a list of available effect types, refer to the separate Data List. The same as the “Mixing Console” on page 122. This parameter enables you to select whether the sound is sustained while you press the keys on the keyboard (“PIANO LIKE”), or the sound is sustained only while you press and hold down the sustain pedal, like playing a real vibraphone (“NORMAL”) (for Vibraphone voice). • If you select [Bright] or [Metallic] as the type of brilliance, the volume level will increase slightly. In this case, raising the [MASTER VOLUME] may result in distortion. If this happens, lower the volume accordingly. • “SPEED” parameter is added when selecting VIBE ROTOR DSP type. This parameter enables you to set the speed of vibrato when you select the Vibraphone voice, recreating the effect of a vibe rotor pedal. HARMONY The explanations here apply to step #3 on page 88. The parameters are the same as for HARMONY/ECHO display of FUNCTION. For details, see page 136. 92 CVP-205/203 Recording Your Performances and Creating Songs — Song Creator With these powerful yet easy-to-use song creating features, you can record your own keyboard performances and store them for future recall. Several different recording methods are available: Quick Recording (page 94), which lets you record easily and quickly; Multi Recording (page 95), which lets you record several different parts; and Step Recording (page 97), which lets you enter notes one by one. Songs can include not only the voice settings for the keyboard performance (Main, Layer, Left), but also the effects and auto accompaniment parts. The recorded song can be stored to internal memory or floppy disk (page 39, 45). METRONOME POWER ON OFF START STOP SONG EXTRA TRACKS (STYLE) TRACK 2 (L) LCD CONTRAST TRACK 1 (R) BACK MENU TOP START / STOP REW FF REPEAT HELP FUNCTION TEMPO TRANSPOSE TAP TEMPO RESET RESET STYLE BREAK INTRO ENDING / rit. MAIN A B C DIGITAL STUDIO SOUND CREATOR MAX AUTO FILLIN A F VARIATION HARMONY / ECHO MONO LEFT HOLD ORGAN & ACCORDION PERCUSSION GUITAR BASS STRINGS CHOIR & PAD SYNTH. XG VOICE PART ON / OFF B G LAYER C H LEFT D I WOODWIND BRASS USER ENTER SYNC.START NEW SONG ACMP DSP E.PIANO VOICE PIANO & HARPSI. GUIDE FADE IN / OUT MIN VOICE EFFECT REVERB NEXT DEMO REC MASTER VOLUME SYNC.STOP SYNC.START START / STOP D DIGITAL RECORDING MIXING CONSOLE ONE TOUCH SETTING MUSIC FINDER 1 2 3 4 J E DATA ENTRY BALANCE PIANO REGISTRATION MEMORY FREEZE 1 2 3 4 5 6 7 8 MEMORY PART CHANNEL OTS LINK ON / OFF PART DIRECT ACCESS 1 2 3 4 5 6 7 8 EXIT SONG EXTRA TRACKS (STYLE) REC NEW SONG TOP TRACK 2 (L) START / STOP DIGITAL RECORDING TRACK 1 (R) REW FF REPEAT GUIDE SYNC.START About Song Recording ■ Quick Recording (page 94) This is the easiest recording method, and lets you quickly record the piano song you are practicing. You can select from three parts: right hand, left hand and auto accompaniment. For example, you can record only your right hand performance, or you can simultaneously record both your right hand and the auto accompaniment. ■ Multi Recording (page 95) This lets you record a song with several different instrument sounds, and create the sound of a full band or orchestra. Record the performance of each instrument individually and create fully orchestrated compositions. You can also record over an existing part on an internal song or a song on disk with your own performance. ■ Step Recording (page 97) This method is like writing music notation on paper. It lets you enter each note individually, by specifying the pitch and length. This is ideal for making precise recordings, or for recording parts that are difficult to play. ■ Song Editing (page 103) The CVP-205/203 also lets you edit the songs you’ve recorded by the Quick Recording, Multi Recording and Step Recording methods. • The internal memory capacity of the Clavinova is about 580KB. Memory capacity for 2DD and 2HD floppy disks is about 720KB and 1.44MB, respectively. When you store data to these locations, all file types of the Clavinova (Voice, Style, Song, Registration, etc.) are stored together. • The microphone input signal (CVP205 only) cannot be recorded. • Songs recorded on theCVP-205/ 203 are automatically recorded as SMF (Standard MIDI File format 0) data. For details on SMF see page 151. • Playback of the recorded song data can be transmitted from MIDI OUT, letting you play the sounds of a connected external tone generator (page 138). • The volume level of each channel of the song can be adjusted from the Mixing Console and the settings can be saved. Moreover, even after you’ve set a voice for your keyboard play during recording, you can record voice selections, so that the voice changes automatically during playback (page 105). CVP-205/203 93 Recording Your Performances and Creating Songs— Song Creator Quick Recording This is the easiest recording method — perfect for quickly recording and playing back a piano song you’re practicing, so you can check your progress. ■ When recording over the part of an internal song or a song on disk with your own performance: ■ When creating a new song: 1 REC NEW SONG TOP START / STOP REW FF REPEAT 1 SYNC.START Select the desired song (page 75, 77). 2 Select the voice and accompaniment style you want to use in the song. If you want to record to the Layer/Left voices, make sure to set the [LAYER]/[LEFT] buttons to ON. Make any other desired settings (Reverb, Chorus, etc.) as well. 3 Simultaneously hold down the [REC] button and press the button corresponding to the track you want to record. You can select TRACK 1 or TRACK 2 and the EXTRA TRACKS for recording at the same time. To record your keyboard performance: Press either the [TRACK 1] or [TRACK 2] button. To record the auto accompaniment performance: Press the [EXTRA TRACKS] button. REC EXTRA TRACKS (STYLE) The performance of track 1/2 is recorded to the channel specified in the SONG SETTING display (page 129). TRACK 2 (L) TRACK 1 (R) To stop recording, press the [REC] button again. 4 Recording starts as soon as you play the keyboard. You can also start recording by pressing the SONG/ STYLE [START/STOP] button. Recording can also be started by pressing down the pedal, if the song start/stop function is properly assigned to the pedal (page 131). END To stop recording, press the [RECORD] button again. Recording can also be stopped by pressing down the pedal, if the song start/ stop function is properly assigned to the pedal (page 131). ■ Play back your new song To play back the performance you just recorded, return the song to the beginning by using the [TOP] button and press the SONG [START/STOP] button. Playback stops automatically at the end of the song, and returns to the beginning of the song. You can edit the recorded song data from the SONG CREATOR (1 - 16) displays (page 106). Press the [6▼] button from the Open/Save display for Song to store the recorded data (page 39, 45). 94 CVP-205/203 If the “LAYER” or “LEFT” button is on before pressing the REC button, the corresponding Layer and Left parts are automatically recorded to different channels. You can overdub a second right-hand performance onto Track 2 after recording the first right-hand performance (including the layer voices) on Track 1. To do this, set the [LEFT] button to OFF and repeat steps 2 and 3. To pause, press the SONG [START/STOP] button. To resume recording, press the SONG [START/STOP] button again. You can also use the metronome click as a guide while recording. The sound of the metronome is not recorded. CAUTION Turning off the power automatically deletes your recorded performance. If you wish to save the recording, make sure to store it to internal memory (USER drive) or floppy disk (page 39, 45). Recording Your Performances and Creating Songs— Song Creator Multi Recording This lets you record a song with several different instrument sounds on up to sixteen channels, and create the sound of a full band or orchestra. The structure of the channels and parts are shown in the chart below. Channels Parts (default settings) Available parts Channels Voice MAIN, LAYER, LEFT Accompaniment style RHYTHM 1 Accompaniment style RHYTHM 2 Accompaniment style BASS Accompaniment style CHORD1 Accompaniment style CHORD2 Accompaniment style PAD Accompaniment style PHRASE1 Accompaniment style PHRASE2 MIDI 1 Voice MAIN 2 Voice MAIN 3 Voice MAIN 4 Voice MAIN 5 Voice MAIN 6 Voice MAIN 14 7 Voice MAIN 15 8 Voice MAIN 16 9 10 11 12 13 Parts (default settings) Accompaniment style RHYTHM 1 Accompaniment style RHYTHM 2 Accompaniment style BASS Accompaniment style CHORD1 Accompaniment style CHORD2 Accompaniment style PAD Accompaniment style PHRASE1 Accompaniment style PHRASE2 Available parts Voice MAIN, LAYER, LEFT Accompaniment style RHYTHM 1 Accompaniment style RHYTHM 2 Accompaniment style BASS Accompaniment style CHORD1 Accompaniment style CHORD2 Accompaniment style PAD Accompaniment style PHRASE1 Accompaniment style PHRASE2 MIDI About the accompaniment style parts Rhythm .....This is the basis for the accompaniment, containing the drum and percussion rhythm patterns. Usually one of the drum kits is used. Bass..........The Bass part uses various appropriate instrument sounds to match the style, such as acoustic bass, synth bass, and others. Chord........This is the rhythmic chord backing, commonly used with piano or guitar voices. Pad ............This part features sustained chords and commonly uses lush sounds such as strings, organ, and choir. Phrase ......This part is used for various embellishments and riffs that enhance the song, such as brass section accents and chord arpeggios. ■ When recording over the part of an internal song or a song on disk with your own performance: ■ When creating a new song: 1 REC TOP NEW SONG 2 START / STOP SYNC.START REW FF REPEAT 1 Select the desired song (page 75, 77). Select the desired channel for recording (set it to “REC”) simultaneously holding down the [REC] button and pressing the appropriate button [1▲▼] - [8▲▼]. Several channels can be selected at the same time. REC ......................... Enables recording for the channel ON ......................... Enables playback of the channel OFF......................... Mutes the channel To cancel or disable recording, press the [REC] button once again. The part is automatically selected when setting the several channels to “REC” at the same time. REC CVP-205/203 95 Recording Your Performances and Creating Songs— Song Creator 3 Select the part you want to assign to the channel to be recorded. This determines which of the keyboard-played parts (Main/Layer/Left) and the accompaniment style parts (RHYTHM 1/2, BASS, etc.) are recorded to the recording channels selected in step #2. For a list of the initial default assignments, see page 95. 4 Recording starts as soon as you play the keyboard. You can also start recording by pressing the SONG/STYLE [START/STOP] button. The recording can be started/stopped by pressing the pedal if the recording punch in/out function is set to the pedal (page 102). When selecting the MIDI part • Setting a single channel to MIDI All incoming data received via any of the MIDI channels 1 - 16 is recorded. When using an external MIDI keyboard or controller to record, this lets you record without having to set the MIDI transmit channel on the external device. • Setting several channels to MIDI When using an external MIDI keyboard or controller to record, this records data only over the set MIDI channel — meaning the external device must also be set to the same channel. A single part (with the exception of MIDI parts) cannot be assigned to several channels. The settings of the recorded parts is stored temporarily until you execute Quick Recording, select a song, or turn the power off. 5 6 To stop recording, press the [REC] button again. You can also use the pedal to stop recording by releasing it, if the recording punch in/out function has been assigned to the pedal (page 102). Play back your new song. To play back the performance you just recorded, return the song to the beginning by using the [TOP] button and press the SONG [START/STOP] button. Playback stops automatically at the end of the song, and returns to the beginning of the song. To pause, press the SONG [START/STOP] button. To resume recording, press the SONG [START/STOP] button again. You can also use the metronome click as a guide while recording. The sound of the metronome is not recorded. CAUTION END 96 CVP-205/203 To record a new part, repeat steps 2 - 6 above. You can set previously recorded parts to play back, and monitor them while you record a new part. Continue in this way until you have a finished song. You can edit the recorded song data from the SONG CREATOR (1 - 16) displays (page 106). Press the [6▼] button from the Open/Save display for Song to store the recorded data (page 39, 45). Turning off the power automatically deletes your recorded performance. If you wish to save the recording, make sure to store it to internal memory (USER drive) or floppy disk (page 39, 45). Recording Your Performances and Creating Songs— Song Creator Recording Individual Notes — Step Record This method lets you create a song by entering notes one by one, without having to perform them in real time. This is also convenient for recording the chords and the melody separately. Operation 1 Select an existing song (page 75, 77) to which you want to add parts or re-record. If you want to create a new song, simultaneously press the [RECORD] button and the [TOP] button. 2 Press the [DIGITAL RECORDING] button. 3 Press the [A] button to call up the Song Creator display. DIGITAL STUDIO SOUND CREATOR DIGITAL RECORDING MIXING CONSOLE PART 4 Using the [BACK]/[NEXT] buttons, select the “1 -16” tab for recording melodies and other parts, or select the “CHD” (Chord) tab for recording chords, and after selecting the “1-16” tab, select a record channel with the [F] (CH) button. 5 Call up the Step Record display by pressing the [G] button. BACK NEXT Any voice, effect and other settings you make in the Mixing Console are automatically cancelled when you call up the CHD (Chord) page. The voices in the USER and FLOPPY DISK pages cannot be selected for Step recording. You can select voices from the PRESET page; however, these may sound slightly different from the original voice. CVP-205/203 97 Recording Your Performances and Creating Songs— Song Creator 6 First, select the desired voice. To enter the note, first specify the length and loudness in this display, then enter the pitch by actually playing the note on the keyboard. Moves the cursor position up and down. Determines the velocity (loudness) of the note to be entered (only when recording the melody). For information on velocity settings, see below. Returns the cursor to the beginning of the song (the first note of the first measure). Determines the length of the note (as a percentage) from the position at which it is to be entered. (This is available only when recording the melody.) For information on gate time settings, see below. Use these to move the selected event, in units of measures (BAR), beat, and clocks. For information on measure/beat/clock settings, see below. END Specifies the type of note to be input next. (Sixteenth notes are available only when recording the melody.) This also determines the position to which the pointer will advance after a note has been entered. Each press of this button toggles among the three basic note selectors at the bottom of the display: normal, dotted, and triplet. (This is available only when recording the melody.) Deletes the event at the cursor. To close the STEP RECORD display, press the [EXIT] button. Make sure to store the recorded data by pressing the [I] (SAVE) button (page 45). ■ Measure/Beat/Clock Measure 1 Beat Clock 1 2 2 3 4 1 000- 000- 000- 0001919 1919 1919 1919 2 3 4 000- 000- 000- 0001919 1919 1919 1919 ■ Velocity The table below shows the available settings and the corresponding velocity values. Kbd. Vel Actual playing strength fff ff f mf mp p pp ppp 127 111 95 79 63 47 31 15 ■ Gate Time The following settings are available: Normal ....................... 80% Tenuto ........................ 99% Staccato...................... 40% Staccatissimo .............. 20% Manual ....................... The gate time (note length) can be specified as a percentage by using the [DATA ENTRY] dial. 98 CVP-205/203 Recording Your Performances and Creating Songs— Song Creator Recording Melodies — Step Record (Note) In this section, we’ll show you how to use Step Recording by guiding you through this actual music example, shown at right. The operations here apply to step 6 on page 98. 1 1-2 1-1 Select this note. 1-3 While holding down this note... ...press this (to input a tie). The notation display on the instrument (CVP-205) may not be accurate, especially for tied notes or longer notes. To have the notation displayed accurately, set the gate time to tenuto by using the [H] button, and input the notes as desired. 2-2 2 2-3 2-4 2-1 Select this note. 3 3-1 Press this button to display the dotted notes. 3-3 3-2 Select this note. 4 4-1 Call up the normal notes by pressing this button. 4-3 4-2 Select this note. To input rests, simply move the measure/beat/clock location for the desired rest time, then input the next note. ■ Play back the newly created melody Use the [C] ( ▲ ) button to move the cursor to the beginning of the song, and press the SONG [START/STOP] button to hear the newly entered notes. To actually enter the recorded data, press the [EXIT] button. The entered data can be edited from the SONG CREATOR (1 - 16) display (page 106). CVP-205/203 99 Recording Your Performances and Creating Songs— Song Creator Recording Chord Changes for the Auto Accompaniment — Step Record (Chord) The Chord Step recording feature makes it possible to record auto accompaniment chord changes one at a time with precise timing. Since the changes don’t have to be played in real time, you can easily create complex, tight chord changes — over which you can record the melody in normal fashion. The operations here apply to step 6 on page 98. Entering Chords and Sections (Chord Step) For example, you can input the following chord progression by the procedure described below. MAIN A C 1 BREAK F G F MAIN B G7 Enter the chords by using the currently selected chord fingering method in the Auto Accompaniment section of the keyboard. C Press the MAIN [A] button to specify the section, and enter the chords as shown at right. MAIN A C MAIN F G C 001:1:000 F Select this note value and play the chords indicated at right. 2 001:3:000 G 002:1:000 Press the [BREAK] button to specify the Break section, and enter the chords as shown at right. MAIN A C BREAK F G F G7 F BREAK 002:3:000 INTRO G7 002:4:000 Select this note value and play the chords indicated at right. 100 CVP-205/203 Recording Your Performances and Creating Songs— Song Creator 3 Press the MAIN [B] button to specify the section and enter the chord indicated at right. MAIN A BREAK MAIN B MAIN C F G F G7 C C 003:1:000 Select this note value and play the chords indicated at right. ■ Play back the newly created chord progression Use the [C] ( ▲ ) button to move the cursor to the beginning of the song, and press the SONG [START/STOP] button to hear the newly entered notes. To actually enter the recorded data, press the [EXIT] button. The entered data can be edited from the SONG CREATOR (CHD) display (page 107). Finally, press the [F] (EXPAND) button from the SONG CREATOR (CHD) display in order to convert the input data into song data. To enter a fill-in, press the [AUTO FILL IN] button and press one of the MAIN [A] – [D] buttons. END Mark An “END” mark is shown in the display, indicating the end of the song data. The actual position of the End mark differs depending on the section that is input at the end of the song. When an Ending section is input, the End mark automatically follows the Ending data. When a section other than Ending is input, the End mark is set two measures after the final section. The End mark can be freely set to any position desired. CVP-205/203 101 Recording Your Performances and Creating Songs— Song Creator Select the Recording Options: Starting, Stopping, Punching In/Out — Rec Mode From this display you can set up how recording is started and stopped for either Quick Recording or Multi Recording. To call up these settings, select the REC MODE display by using the [BACK][NEXT] button, after performing operation steps 1 - 3 on page 97. These settings determine how recording will start. Normal Pressing the SONG [START/STOP] button enables Synchro standby and overwrite recording starts as soon as you start playing the keyboard. Calls up the SONG display, from which you can save the edited data. First Key On Overwrite recording starts as soon as you start playing the keyboard. This setting also preserves the previous lead-in data, letting you record over the original lead-in without erasing it. When this is set to ON, you can use the sostenuto (center) pedal to control the punch-in and punch-out points. Press and hold down the sostenuto pedal to record. Recording stops when you release the pedal. Punch In At The song plays back normally up to the indicated Punch In measure (set by the [3▲▼] buttons), then starts overwrite recording at that Punch In measure. These settings determine how recording will stop as well as what happens to previously recorded data. Determines the measure at which Punch In overwrite recording starts (when “PUNCH IN AT” is selected). Replace All This deletes all data following the point at which recording is stopped. Punch Out This maintains all data following the point at which recording is stopped. Punch Out At Overwrite recording continues until the indicated Punch Out measure (set by the [6▲▼] buttons), then stops at that Punch Out measure, after which song playback continues normally. Determines the Punch Out measure — the measure at which Punch In overwrite recording stops (when “PUNCH OUT AT” is selected). When the Pedal Punch In/ Out function is set to ON, the current function assignment of the sostenuto pedal is cancelled. About Punch In/Out This feature is useful primarily for re-recording or replacing a specific section of an already recorded channel. The illustrations below indicate a variety of situations in which selected measures in an eight-measure phrase are re-recorded. REC START setting REC END setting NORMAL REPLACE ALL NORMAL PUNCH OUT NORMAL PUNCH OUT AT=006 FIRST KEY ON REPLACE ALL FIRST KEY ON PUNCH OUT FIRST KEY ON PUNCH OUT AT=006 PUNCH IN AT=003 REPLACE ALL PUNCH IN AT=003 PUNCH OUT PUNCH IN AT=003 PUNCH OUT AT=006 102 CVP-205/203 Original data 1 2 3 4 2 3 4 2 3 4 1 1 Start/ play back original data 1 Start/ play back original data 1 Start/ play back original data 1 Start/ play back original data 1 Start/ play back original data 1 8 5 *1 When measures 1 - 2 are not overwritten, recording starts from measure 3. *2 You’ll have to press the [REC] button at the end of 5 measures. Deleted 5 6 7 8 7 8 Stop overwrite recording/ play original data Start/start overwrite recording *1 Start/ play back original data 7 Stop recording *2 Start/start overwrite recording *1 1 6 Stop recording *2 Start/start overwrite recording *1 1 5 2 3 4 Start playing the keys/ start overwrite recording 2 3 3 4 3 4 3 4 3 4 3 6 7 8 5 6 7 8 5 Deleted Stop recording *2 4 5 6 7 Stop overwrite recording/ play original data Start overwrite recording 2 5 Stop recording *2 Start overwrite recording 2 Deleted Stop overwrite recording/ play original data Start overwrite recording 2 5 Stop recording *2 Start playing the keys/ start overwrite recording 2 6 Stop recording *2 Start playing the keys/ start overwrite recording 2 5 4 5 7 8 Previously recorded data Newly recorded data Deleted data Recording Your Performances and Creating Songs— Song Creator Editing a Recorded Song Whether you’ve recorded a song using Quick Recording, Multi Recording, or Step Recording, you can use the editing features to change the song data. Editing Channel-related Parameters — Channel Calling up the operations here apply to step 4 on page 97. To call up the display shown below, use the [BACK]/[NEXT] buttons. Quantize Quantize lets you “clean up” or tighten the timing of a previously recorded channel. For example, the following musical passage has been written with exact quarter-note and eighth-note values. Even though you think you may have recorded the passage accurately, your actual performance may be slightly ahead of or behind the beat. Quantize allows you to align all the notes in a channel so that the timing is absolutely accurate to the specified note value (see below). Use this to select the desired edit operation. Calls up the SONG display, from which you can save the edited data. Executes the Quantize operation. After the operation is completed, this button changes to [UNDO], letting you restore the original data if you’re not satisfied with the Quantize results. The Undo function only has one level; only the previous operation can be undone. Selects the desired channel to be quantized. Selects the quantize size (resolution). See the below for the details. Determines how strongly the notes will be quantized. If a value less than 100% is selected, notes will be moved toward the specified quantization beats only by the specified amount. Applying less than 100% quantization lets you preserve some of the “human” feel in the recording. ■ About Quantize Size Set the Quantize size to correspond to the smallest notes in the channel you are working with. For example, if the data was recorded with both quarter notes and eighth notes, use 1/8 note for the Quantize size. If you apply a 1/4 note Quantize size, the eighth notes would be moved on top of the quarter notes. One measure of eighth notes before quantization After 1/8 note quantization Quantize Size 1/4 note 1/4 note triplet 1/8 note 1/8 note triplet 1/16 note 1/16 note triplet 1/32 note 1/8 note + 1/8 note triplet * 1/16 note + 1/8 note triplet * 1/16 note + 1/16 note triplet * The three Quantize settings marked with asterisks (*) are exceptionally convenient, since they allow you to quantize two different note values at the same time, without compromising the quantization of either one. For example, if you have both straight 1/8 notes and 1/8 note triplets recorded to the same channel, and you quantize to straight 1/8 notes, all notes in the channel are quantized to straight 1/8 notes — completely eliminating any triplet feel in the rhythm. However, if you use the 1/8 note + 1/8 note triplet setting, both the straight and triplet notes will be quantized correctly. CVP-205/203 103 Recording Your Performances and Creating Songs— Song Creator Delete This lets you delete recorded data in the specified channel. Use these to select the desired edit operation. Deletes all data in the selected channel. After the operation is completed, this button changes to [UNDO], letting you restore the original data. The Undo function only has one level; only the previous operation can be undone. Calls up the SONG display, from which you can save the edited data. These select the channel to be deleted. Mix This function lets you mix the data of two channels and place the results in a different channel. It also lets you copy the data from one channel to another. All data other than the mixed note data is derived from the Source 1 channel. Use these to select the desired edit operation. Executes the Mix operation. After the operation is completed, this button changes to [UNDO], letting you restore the original data if you’re not satisfied with the Mix results. The Undo function only has one level; only the previous operation can be undone. Calls up the SONG display, from which you can save the edited data. These let you specify the two source channels to be mixed. Determines the channel into which the mix or copy results will be placed. If “COPY” is selected here, the data from Source 1 is copied to the Destination channel. 104 CVP-205/203 Recording Your Performances and Creating Songs— Song Creator Channel Transpose This allows you to transpose the recorded data of individual channels up or down by a maximum of two octaves in semitone increments. Toggles between the two channel displays: Channels 1 - 8, and Channels 9 - 16. Use these to select the desired edit operation. To simultaneously set all channels to the same value, adjust the Channel Transpose for one of the channels while holding down this button. Executes the Channel Transpose operation. After the operation is completed, this button changes to [UNDO], letting you restore the original data if you’re not satisfied with the Channel Transpose results. The Undo function only has one level; only the previous operation can be undone. Calls up the SONG display, from which you can save the edited data. Determines the amount of transpose for each channel. Set Up You can change the initial settings of the song — such as voice, level, and tempo — to the current settings of the mixing console or panel controls. Use these to select the desired edit operation. Executes the SET UP operation. Once SET UP has been executed, the operation cannot be cancelled or undone. Calls up the SONG display, from which you can save the edited data. Use this to checkmark the selected item. Checkmarked items are stored with the song. Determines which playback features and functions will be automatically called up along with the selected song. All events, with the exception of “KEYBOARD VOICE,” can be recorded only at the beginning of the song. Before you select or checkmark any of these items (other than Keyboard Voice), make sure to return the song to the beginning by using the [TOP] button, and stop playback. Song.............................Stores the tempo setting and all settings made from the Mixing Console. Keyboard Voice ...........This lets you automatically set the voice of the keyboard-played parts (Main/Layer/Left) when playing back the song. Stores the keyboard-played voice and the part ON/OFF settings. To record a voice change for the keyboard-played part in the middle of a song, stop the song at the desired point, make the voice change, and press the [D] (EXECUTE) button. Lyrics Language .........Stores the settings of the Lyrics display. Score Setting ..............Stores the settings of the Score display (CVP-205 only). Guide Setting ..............Stores the settings of the practice functions. When the settings are stored, selecting a song automatically turns on the Guide functions. Mic. Setting..................Stores the microphone settings in the mixing console (CVP-205 only). CVP-205/203 105 Recording Your Performances and Creating Songs— Song Creator Editing Note Events — 1 - 16 From this display, you can edit individual note events (see below). Calling up operations here apply to step 4 on page 97. Use the [BACK]/[NEXT] buttons to call up the display below. Determines the channel to be edited. Use these to move the cursor up/down and select the desired event. Calls up the Step Recording display (page 98). Returns to the beginning position of the current song (the first note of the first measure). Calls up the Filter display (page 108), letting you select only the events you wish to shown in the Event List. Use these to move the cursor left/right and select the desired parameter of the highlighted event. Keep in mind that moving the cursor away from the justedited value automatically enters that value. Calls up the SONG display, from which you can save the edited data. Holding this button down while using the [A] and [B] buttons lets you select multiple events. Pastes all cut or copied events to the selected location. Determines the current position of the event being edited. If the value at the cursor has been changed, pressing this restores the original value. For coarse adjustment of the event value. For fine adjustment of the event value. Cuts (deletes) all selected events. The cut events are copied and can be pasted to another location. Adds a new event to the Event List. Copies all selected events. The copied events can be pasted to another location. Deletes the event at the cursor position. To actually enter an edited value, move the cursor away from the value or press the SONG [START/STOP] button. Note Events Parameter Note Ctrl (Control change) Prog (Program change) P.Bnd (Pitch bend) A.T. (After touch) Description Determines the pitch, velocity (volume) and length of the note. Determines the control change number and value. For details on control change messages, refer to the separate Data List booklet (MIDI Data Format). Determines the voice (program) number. For details on program change messages and how to set them, refer to the separate Data List booklet (Voice List). Determines the pitch bend value. Determines the after touch value. The sound of the voices recorded with Step recording may sound slightly different from the original. 106 CVP-205/203 Recording Your Performances and Creating Songs— Song Creator Editing Chord Events — CHD From this display, you can edit the chord events you’ve recorded to the song. Calling up operations here apply to step 4 on page 97. Use the [BACK]/[NEXT] buttons to call up the display below. With the exception of the [F] (EXPAND) button, the operations here are the same as those in Editing Note Events (page 106). Press this to convert the recorded chord and section entries into song data. To actually enter an edited value, move the cursor away from the value or press the SONG [START/STOP] button. Chord Events Parameter Style (Accompaniment style) Tempo Chord Sect (Section) OnOff (Channel on/off) CH.Vol (Channel volume) S.Vol (Style volume) Description Displays the accompaniment style name. To enter an accompaniment style, call up the STYLE display and select the desired style. Determines the tempo value. Specifies the chord — its root note, chord type, and on-bass note. Specifies the section — its name and variation. Determines whether specific channels (rhythm, bass, etc.) are turned on/off. Determines the level of specific channels (rhythm, bass, etc.). Determines the level of the entire accompaniment style. Editing System Events — SYS/EX. (System Exclusive) From this display, you can edit recorded System events. Calling up operations here apply to step 4 on page 97. Use the [BACK]/[NEXT] buttons to call up the display below. The operations here are the same as those in Editing Note Events (page 106). System Events Parameter Description ScBar (Score initial measure) This determines the number of the top measure. The measure number is indicated in the MAIN display or in the music notation (CVP-205 only). Only one value can be specified at the beginning of the song data. Tempo Determines the tempo value. Time (Time signature) Determines the time signature. Key Determines the key, as well as the major/minor setting. XG Prm (XG parameters) Allows you to make various detailed changes to the data. For more information on XG parameters, refer to the separate Data List booklet (MIDI Data Format). SysEx (System Exclusive) Displays the System Exclusive data in the song. This does not let you change the actual contents of the data; however, it lets you delete, cut, copy, and paste the data. Meta (Meta event) Displays the SMF meta events in the song. This does not let you change the actual contents of the data; however, it lets you delete, cut, copy, and paste the data. CVP-205/203 107 Recording Your Performances and Creating Songs— Song Creator Inputting and Editing Lyrics This convenient function lets you enter the song name and the lyrics for the song. It also lets you change or correct already existing lyrics. For more information on lyric events, see the chart below. Calling up operations here apply to step 4 on page 97. Use the [BACK]/[NEXT] buttons to call up the display below. The operations here are the same as those in Editing Note Events (page 106). In the following example, we’ll rewrite a portion of the lyrics to one of the songs, “Twinkle Twinkle Little Star.” Select the disk song (CVP-203) / internal song (CVP-205) “Twinkle Twinkle Little Star.” The method for selection is the same as described on page 75. 1 Move the cursor to the event containing the lyric “star.” 2 Move the cursor to the word “star.” The song “Twinkle Twinkle Little Star” is in the folder “For Children” in the Song Book (page 75). Use these buttons to call up the Lyric display, from which you can input lyrics. From the Lyric display (page 46), enter the new word, “(your name).” To actually enter an edited value, move the cursor away from the value or press the SONG [START/STOP] button. 3 4 Press this button to save the newly changed lyric data. Lyrics Events Parameter Name (Song name) Lyrics Code (Other controls) Description Determines the song name. This calls up the NAME display, from which you can enter the name. Allows you to enter lyrics. CR : Enters a line break in the lyrics text. LF : Deletes the currently displayed lyrics and displays the next set of lyrics. Customizing the Event List — Filter This function lets you determine which event types will be shown in the event editing displays. To select an event for display, checkmark the box corresponding to the event name. To filter out an event so that it is not shown on the list, remove the checkmark so that the box is empty. To call up the display below, press the [H] (FILTER) button from any of the following displays: CHD, 1 - 16, SysEX, or LYRICS (page 106 - page 108). Calls up the Main Filter display. For more information on each event type, refer to the separate Data List booklet (MIDI Data Format). Calls up the Control Change Filter display. For more information on each event type, refer to the separate Data List booklet (MIDI Data Format). Calls up the Accompaniment Filter display. For more information on each event type, refer to the separate Data List booklet (MIDI Data Format). END 108 CVP-205/203 EXIT Execute the settings by pressing the [EXIT] button. Enters checkmarks for all items. Selects only note data; checkmarks for all other boxes are removed. Reverses the checkmark settings for all boxes. In other words, this enters checkmarks to all boxes that were previously un-checked and vice versa. Enters/removes the checkmark for the selected item. Selects the item, scrolling up/down one item at a time. When “MAIN FILTER” or “ACCOMPANIMENT FILTER” is selected, these select the item, scrolling up/down to the top or the bottom. When “CONTROL CHANGE FILTER” is selected, these select the item, scrolling up/down eight items at a time. Creating Accompaniment Styles — Style Creator This powerful feature lets you create your own original styles, which can then be used for auto accompaniment — just as with the preset styles. METRONOME POWER ON OFF START STOP SONG EXTRA TRACKS (STYLE) TRACK 2 (L) LCD CONTRAST TRACK 1 (R) BACK MENU TOP START / STOP REW FF REPEAT HELP A FUNCTION TEMPO DIGITAL STUDIO TRANSPOSE TAP TEMPO SOUND CREATOR MAX MIN RESET DIGITAL RECORDING RESET STYLE AUTO FILLIN BREAK INTRO ENDING / rit. MAIN A F VARIATION HARMONY / ECHO MONO LEFT HOLD ORGAN & ACCORDION PERCUSSION GUITAR BASS STRINGS CHOIR & PAD SYNTH. XG VOICE PART ON / OFF B G LAYER C H LEFT D I BRASS USER ENTER SYNC.START NEW SONG FADE IN / OUT ACMP DSP E.PIANO WOODWIND VOICE PIANO & HARPSI. GUIDE MASTER VOLUME DIGITAL RECORDING VOICE EFFECT REVERB NEXT DEMO REC B C 1 2 3 4 J E MIXING CONSOLE SYNC.STOP SYNC.START START / STOP D ONE TOUCH SETTING MUSIC FINDER DATA ENTRY BALANCE PIANO REGISTRATION MEMORY FREEZE 1 2 3 4 5 6 7 8 MEMORY PART CHANNEL OTS LINK ON / OFF PART STYLE ACMP 1 DIRECT ACCESS AUTO FILLIN BREAK INTRO A B 2 3 4 5 ENDING / rit. MAIN C 6 7 8 EXIT SYNC.STOP SYNC.START START / STOP D OTS LINK About Creating Accompaniment Styles The chart at right shows the basic parts (or “channels”) that make up each section of an accompaniment style. To create an accompaniment style, record patterns to the various channels one by one, for each of the sections you want to create. Section Channel INTRO A - D MAIN A - D ■ Realtime Recording (page 111) FILL IN A - D You can record accompaniment styles by simply playing the parts from the keyboard in real time. However, you don’t have to record every part yourself — you can choose an existing preset accompaniment style that is close to the style you want, then add or replace parts in that style as needed to create your own custom style. BREAK RHYTHM 1, RHYTHM 2, BASS, CHORD 1, CHORD 2, PAD, PHRASE 1, PHRASE 2 ENDING A - D For information on the part structure of accompaniment styles, see page 95. Realtime Recording Characteristics • Loop recording Since auto accompaniment playback repeats the accompaniment patterns of several measures in a “loop,” you can also record patterns in a loop. For example, if you start recording with a two-measure Main section, the two measures are repeatedly recorded. Notes that you record will play back from the next loop (repetition), letting you record new material while hearing the parts you previously recorded. • Overdub recording This feature lets you record new material to a track already containing recorded data, without deleting the original data. In style recording, the recorded data remains intact, unless you specifically delete it yourself. For example, if you start recording with a two-measure Main section, the two measures are repeated. As you record notes to each pass of the loop (repetition), those notes play back from the next loop, letting you overdub new material while hearing the previous parts. ■ Step Recording (page 112) This method is like writing music notation on paper, since it allows you to enter each note or individually, and specify its length. This is ideal for making precise recordings, or for recording parts that are difficult to play. ■ Assembling an Accompaniment Style (page 113) This convenient feature lets you create composite styles by combining various patterns from the internal preset accompaniment styles. For example, if you want to create your own original 8-beat style, you could take rhythm patterns from the “8 Beat 1” style, use the bass pattern from “8 Beat 2,” and import the chord patterns from the “60’s 8 Beat” style — combining the various elements to create one accompaniment style. ■ Editing the created Accompaniment Style (page 114) With the editing features, you can custom edit the styles you’ve created by real time recording, step recording, and assembling from other styles. 8Beat 1 Rhythm 1 Rhythm 2 Bass Chord 1 Chord 2 Pad Phrase 1 Phrase 2 60’s 8 Beat Rhythm 1 Rhythm 2 Bass Chord 1 Rhythm 1 Rhythm 2 Bass Chord 1 Chord 2 Pad Phrase 1 Phrase 2 Chord 2 8Beat 2 Rhythm 1 Rhythm 2 Bass Chord 1 Chord 2 Pad Phrase 1 Phrase 2 Pad Phrase 1 Phrase 2 CVP-205/203 109 Creating Accompaniment Styles — Style Creator Style File Format The Style File Format (SFF) combines all of Yamaha’s auto accompaniment know-how into a single unified format. By using the edit functions, you can take full advantage of the SFF format and freely create your own styles. The chart at right indicates the process by which the accompaniment is played back. (This does not apply to the rhythm tracks.)The basic or “source” pattern in the chart is the original style data. This source pattern is recorded using accompaniment style recording (see below). As shown in the chart at right, the actual output of the accompaniment is determined by various parameter settings and chord changes (played in Auto Accompaniment section of the keyboard) entered to this source pattern. These are the patterns recorded to the accompaniment styles (page 117). Source Pattern 1 Source Root (root note of basic chord) 2 Source Chord (type of basic chord) Chord changes (in Auto Accompaniment section of the keyboard) This data is created by chords played in the Auto Accompaniment section of the keyboard (page 63). Pitch Conversion 3 NTR (Note Transposition Rule) 4 NTT (Note Transposition Table) These settings are edited from the PARAMETER display. These parameters determine how the pitch of the source pattern is converted when you play chords in the Auto Accompaniment section of the keyboard (page 117). Other Settings 5 High Key (threshold of the pitch conversion) 6 Note Limit (soundable range) 7 RTR (Retrigger Rule; how the pitches of the chord change) Output Operation 1 Select the desired accompaniment style for editing. To record a new accompaniment style from scratch, call up the BASIC page in the Style Creator display and select “New Style” by pressing the [C] button. 2 3 DIGITAL STUDIO SOUND CREATOR DIGITAL RECORDING MIXING CONSOLE PART 4 5 110 Record and edit the accompaniment style. For details on the operations for each display, refer to the explanations starting on the next page. Call up the Style display by pressing the [I] (SAVE) button (in Assembly page: [J] button), then save the recorded / edited data to the USER or FLOPPY DISK page. CVP-205/203 BACK NEXT Use the [BACK]/[NEXT] buttons to select the various pages. END Press the [EXIT] button to close the STYLE CREATOR display. Creating Accompaniment Styles — Style Creator Realtime Recording — Basic You can use the Realtime Recording features to create your own accompaniment style — either from scratch or based on the preset accompaniment data. The operations here apply to step 4 on page 110. 1 Select the desired channel for recording by simultaneously holding down the [F] (REC CH) button and pressing the appropriate [1▲▼] - [8▲▼] button. Before recording to one of the non-rhythm channels (BASS - PHR 2), make sure to delete the existing data of the appropriate channel. You can make other settings (see the box “Other Parameters in the BASIC Display” on page 112) after closing the REC CHANNEL display by pressing the [EXIT] button. To call up the REC CHANNEL display again, press the [F] (REC CH) button. Calls up the display for changing the tempo or beat (time signature). Selects an empty style, allowing you to create a new style from scratch. Available only when the channel is set to [RHY1] or [RHY2], this lets you delete specific percussion sounds during recording. Simultaneously hold down this button and press the key corresponding to the instrument you want to delete. When this button is pressed, “DELETE” will appear over channels containing data. To delete data from a specific channel, simultaneously hold down this button and press the appropriate [1▲] - [8▲] button. To release or cancel the selection, press the [1▼] [8▼] button corresponding to the channel you wish to cancel. As long as you continue to hold down the [J] button, you can toggle between deleting and restoring the selected data. Releasing the [J] button permanently deletes the data. Before recording to one of the non-rhythm channels (BASS - PHR 2), make sure to delete the existing data of the appropriate channel. REC.... Channel is enabled for recording. ON ...... Channel is enabled for playback. OFF .... Channel is muted. 2 First, select the desired voice. Start recording by pressing the STYLE [START/ STOP] button. The selected section of the style starts playing back. Since the rhythm pattern loops repeatedly, you can record new sounds and notes on each pass while listening to the pattern. Icons above the keys conveniently indicate the percussion instruments assigned to the keys. 3 Stop recording by pressing the STYLE [START/STOP] button again. END With the REC CHANNEL display shown, close the display by pressing the [EXIT] button. If you’ve enabled Sync Start (by pressing the SYNC. START button), you can start recording by simply pressing a key on the keyboard. • Only Drum Kit/SFX Kit can be selected for the RHY 2 channel. • For the non-rhythm channels (BASS - PHR 2), all voices with the exception of the Drum Kit/SFX Kit can be selected. CVP-205/203 111 Creating Accompaniment Styles — Style Creator Other Parameters in the BASIC Display [I] (SAVE) button Calls up the Style display for saving the accompaniment style data. [3▲▼][4▲▼] (Section) buttons Determines the section to be recorded. [5▲▼][6▲▼] (Pattern Length) buttons Determines the length of the selected section’s pattern in measures (1 - 32). The Fill In/Break section is fixed at a length of one measure. [D] (Execute) button Executes the Pattern Length change. You can also select the desired section for recording by pressing the appropriate panel button. Pressing one of the Section buttons calls up the SECTION display, from which you can change sections by using the [6▲▼]/ [7▲▼] buttons. To actually enter the change, press the [8▲] button. To select the Fill In section, press the [AUTO FILL IN] button. Recording — Precautions • The basic chord used for the accompaniment style is called the source chord. All chords that play and the pitches that sound are derived from the source chord. When C R C C R C recording the Main and Fill In sections (for a source chord of CM7), keep the C = chord note following points in mind: C, R = recommended note * When recording to the Bass or Phrase channels, try to use only the recommended notes; this will ensure that you can play various chords with the accompaniment style and get optimum results. (Other notes may work, providing you use them as short passing tones.) * When recording to the Chord or Pad channels, use only the notes of the CM7 chord; this will ensure that you can play various chords with the accompaniment style and get optimum results. (Other notes may work, providing you use them as short passing tones.) The source chord is set by default to CM7; however, you can change this to any chord you prefer. Refer to the section “Making Style File Format Settings – Parameter” on page 117. • When recording Intro and Ending sections, you can ignore the source chord and use any notes or chord progressions you like. In this case, if you set the NTR parameter to “ROOT TRANSPOSE” and NTT to “HARMONIC MINOR” or “MELODIC MINER” (in the PARAMETER page), the normal pitch conversions that would result from playing different chords are cancelled (for playback) — meaning that the accompaniment pitch conversion will only occur for changes in the root note or major/minor shifts. Step Recording With this method, you can create a style pattern by entering notes and other data individually, without having to perform them in real time. The operations here apply to step 4 on page 110. The actual recording process is the same as in Step Recording of songs (page 97), with the exception of the points described below. You can also edit each event from the Edit page, and the editing process the same as in editing songs (page 106). • In song recording, the end mark position can be changed freely. However, it cannot be changed when creating accompaniment styles. This is because the length of the accompaniment style is automatically fixed according to the selected section. For example, when creating an accompaniment style based on a four-measure section, the end mark position is automatically set to the end of the fourth measure, and cannot be changed from the Step Record screen. • When editing the data recorded on the Edit page, you can switch between the type of data you want to edit (event data or control data). Press the [F] (TRACK EVT) button to switch between the Event display (Note, Control Change, etc.) and the Control display (System Exclusive, etc.). Make sure to set the record channel from another display (e.g., BASIC display; page 111) beforehand. 112 CVP-205/203 Creating Accompaniment Styles — Style Creator Assembling an Accompaniment Style —Assembly This convenient function lets you combine accompaniment elements — such as rhythm, bass, and chord patterns — from existing styles, and use them to create your own original accompaniment styles. The operations here apply to step 4 on page 110. 1 These let you select the accompaniment style that will be used for each channel of your original style. Select the desired channel by pressing the [A] – [D], [F] – [I] buttons and press the same button to call up the Style screen, from which you can select the accompaniment style. 3 After repeating steps 1 and 2 as desired, press the [J] (SAVE) button to save the assembled style data. From here, you can store the settings of all channels (RHYTHM1, RHYTHM2, BASS, etc.) to a single accompaniment style. If you change the section and channel in steps #1 and #2, the currently specified section and channel are also changed. The channels being recorded are also changed and recording is stopped automatically. 2 Selects the style section and channel that will be copied to the corresponding channels, selected with the [A]-[D] and [F]-[I] buttons above. The PLAY TYPE parameter affects only the playback, and does not change the actual accompaniment style data. Determines the playback settings for each channel. You can assemble the accompaniment style while the style section and channel that will be copied are playing. SOLO ........... Mutes all but the selected channel. RHYTHM channels set to REC in the REC CHANNEL display (page 111) are played back simultaneously. ON ............... Plays back the selected channels. Any channels set to ON in the REC CHANNEL display (page 111) are played back simultaneously. OFF .............. Mutes the selected channel. If the selected channel is set to ON in the REC CHANNEL display (page 111), OFF does not appear and is not available. CVP-205/203 113 Creating Accompaniment Styles — Style Creator Edit the Created Accompaniment Style Change the Rhythmic Feel — Groove and Dynamics These versatile features give you a wide variety of tools for changing the rhythmic feel of your created accompaniment style. The operations here apply to step 4 on page 110. ■ Groove Use these to select the desired edit operation. Executes the Groove operation. After the operation is completed, this button changes to [UNDO], letting you restore the original data if you’re not satisfied with the Groove results. The Undo function only has one level; only the previous operation can be undone. Calls up the Style display and lets you store the edited accompaniment style data. Determines the settings for each of the Groove parameters (see the list below). Groove parameters 114 Original Beat Specifies the beats to which Groove timing is to be applied. In other words, if “8 Beat” is selected, Groove timing is applied to the 8th notes; if “12 Beat” is selected, Groove timing is applied to 8th-note triplets. Beat Converter Actually changes the timing of the beats (specified in the ORIGINAL BEAT parameter above) to the selected value. For example, when ORIGINAL BEAT is set to “8 Beat” and BEAT CONVERTER is set to “12,” all 8th notes in the section are shifted to 8th-note triplet timing. The “16A” and “16B” Beat Converter which appear when ORIGINAL BEAT is set to “12 Beat” are variations on a basic 16th-note setting. Swing Produces a “swing” feel by shifting the timing of the back beats, depending on the ORIGINAL BEAT parameter above. For example, if the specified ORIGINAL BEAT value is “8 Beat”, the Swing parameter will selectively delay the 2nd, 4th, 6th, and 8th beats of each measure to create a swing feel. The settings “A” through “E” produce different degrees of swing, with “A” being the most subtle and “E” being the most pronounced. Fine Selects a variety of Groove “templates” to be applied to the selected section. The “PUSH” settings cause certain beats to be played early, while “HEAVY” settings delay the timing of certain beats. The numbered settings (2, 3, 4, 5) determine which beats are to be affected. All beats up to the specified beat —but not including the first beat — will be played early or delayed (for example, the 2nd and 3rd beats, if “3” is selected). In all cases, “A” types produce minimum effect, “B” types produce medium effect, and “C” types produce maximum effect. CVP-205/203 Creating Accompaniment Styles — Style Creator ■ Dynamics Use these to select the desired edit operation. Calls up the Style display and lets you store the edited accompaniment style data. Executes the Dynamics operation. After the operation is completed, this button changes to [UNDO], letting you restore the original data if you’re not satisfied with the Dynamics results. The Undo function only has one level; only the previous operation can be undone. Select the desired channel to which Dynamics is to be applied. Determines the settings for each of the Dynamics parameters (see the list below). Dynamics parameters Accent Type Selects the type of accent. Strength Determines how strongly the selected Accent Type (above) will be applied. The higher the value, the stronger the effect. Expand/Compress Expands or compresses the range of velocity values, around a central velocity value “64.” Values higher than 100% expand the dynamic range, while values lower than 100% compress it. Boost/Cut Boosts or cuts all velocity values in the selected section/channel. Values above 100% boost the overall velocity, while values below 100% reduce it. Velocity is determined by how strongly you play the keyboard. The more strongly you play the keyboard, the higher the velocity value and, hence, the louder the sound. CVP-205/203 115 Creating Accompaniment Styles — Style Creator Editing the Channel Data In this display, there are five different channel-related edit functions, including Quantize, for editing the recorded accompaniment style data. The operations here apply to step 4 on page 110. See the explanations below. Preset channel BASSPHRASE2 can not be edited. ■ Quantize Refer to page 103. ■ Velocity Change Boosts or cuts the velocity of all notes in the specified channel (selected with the [1▲▼]/[2▲▼] (CHANNEL) buttons), according to the specified percentage (selected with the [4▲▼]/[5▲▼] (BOOST/CUT) buttons). ■ Bar Copy This function allows data to be copied from one measure or group of measures to another location within the specified channel. Use the [4▲▼] (TOP) and [5▲▼] (LAST) buttons to specify the first and last measures in the region to be copied. Use the [6▲▼] (DEST) button to specify the first measure of the destination location, to which the data is to be copied. ■ Bar Clear This function clears all data from the specified range of measures within the selected channel. Use the [4▲▼] (TOP) and [5▲▼] (LAST) buttons to specify the first and last measures in the region to be cleared. ■ Remove Event This function lets you remove specific events from the selected channel. Use the [4▲▼] - [6▲▼] (EVENT) buttons to select the desired event type to be removed. 116 CVP-205/203 Creating Accompaniment Styles — Style Creator Making Style File Format Settings —Parameter This display provides a variety of style controls— such as determining how the pitch and sound of the recorded style change when playing the chords in the left-hand range of the keyboard. For details about the relationship between the parameters, refer to “Style File Format” on page 110. The operations here are the same as described in step 4 on page 110. When NTR is set to “Root Fixed” and NTT is set to “Bypass,” the “Source Root” and “Source Chord” parameters are changed to “Play Root” and “Play Chord,” respectively. In this case, you can change chords and hear the resulting sound for all channels. See the explanations below. ■ Source Root/Chord These settings determine the original key of the source pattern (i.e., the key used when recording the pattern). The default setting of CM7 (with a Source Root of “C” and a Source Type of“M7”), is automatically selected whenever the preset data is deleted prior to recording a new style, regardless of the Source Root and Chord included in the preset data. When you change Source Root / Chord from the default CM7 to another chord, the chord notes and recommended notes will also change, depending on the newly selected chord type. For details on chord notes and recommended notes, see page 112. When the Source Root is C: C6 CMaj CM711 CM7 CM79 C9 C69 C C R C C R C R C C C R Cm Caug R C R Cm711 C R C C7 5 C C C C C C C C R C R C R C C C C C C C1+5 C C C C R C C C C C R C C C C R C C C C C C R C C C C C C R C C C R C C C = chord note C, R = recommended note R C C C R C C C C79 Csus2 Csus4 C R C C7sus4 C713 C C C R C R C C R R C C C C C7 C C C R C Cm79 C C C79 C C R C C R C R C R C C R R C C R R C C C Cm9 C C713 C C R C C R Cdim7 C R C C1+8 C7aug CM7aug C C C R C Cdim C711 C79 C R C C C C C C C Cm75 C R C C CmM79 R C C R C Cm7 C R C C R C C C R C C C CmM7 C C R C R C Cm6 C R C R C C R C C R ■ NTR (Note Transposition Rule) and NTT (Note Transposition Table) • NTR (Note Transposition Rule) This determines the system for pitch conversion of the source pattern. Two settings are available. Root Trans (Root Transpose) When the root note is transposed, the pitch relationship between notes is maintained. For example, the notes C3, E3 and G3 in the key of C become F3, A3 and C4 when they are transposed to F. Use this setting for channels that contain melody lines. Root Fixed The note is kept as close as possible to the previous note range. For example, the notes C3, E3 and G3 in the key of C become C3, F3 and A3 when they are transposed to F. Use this setting for channels that contain chord parts. CVP-205/203 117 Creating Accompaniment Styles — Style Creator • NTT (Note Transposition Table) This sets the note transposition table for the source pattern. Six transposition types are available. Bypass No transposition. Melody Suitable for melody line transposition. Use this for melody channels such as Phrase 1 and Phrase 2. Chord Suitable for chord transposition. Use for the Chord 1 and Chord 2 channels, especially when they contain piano or guitar-like chordal parts. Bass Suitable for bass line transposition. This table is basically similar to the Melody table above, but recognizes onbass chords allowed in the FINGERED ON BASS fingering mode. Use this primarily for bass lines. Melodic Minor When the played chord changes from a major to a minor chord, this table lowers the third interval in the scale by a semitone. When the chord changes from a minor to a major chord, the minor third interval is raised by a semitone. Other notes are not changed. Harmonic Minor When the played chord changes from a major to a minor chord, this table lowers the third and sixth intervals in the scale by a semitone. When the chord changes from a minor to a major chord, the minor third and flatted sixth intervals are raised by a semitone. Other notes are not changed. ■ High Key/Note Limit • High Key This sets the highest key (upper octave limit) of the note transposition for the chord root change. Any notes calculated to be higher than the highest key are transposed down to the octave just below the highest key. This setting is effective only when the NTR parameter (page 117) is set to “Root Trans.” • Note Limit This sets the note range (highest and lowest notes) for voices recorded to the style channels. By judicious setting of this range, you can ensure that the voices sound as realistic as possible — in other words, that no notes outside the natural range are sounded (e.g., high bass sounds or low piccolo sound). The actual notes that sound are automatically shifted to the set range. Example — When the highest key is F Root changes CM CM Notes played C3-E3-G3 C 3-F3-G 3 FM F3-A3-C4 FM F 2-A 2-C 3 Example — When the lowest note is C3 and the highest is D4 Root changes CM CM FM 3-C4 E3-G3-C4 F3-G F3-A3-C4 Notes played High Limit Low Limit ■ RTR (Retrigger Rule) These settings determine whether notes stop sounding or not and how they change pitch in response to chord changes. Stop The notes stop sounding. Pitch Shift The pitch of the note will bend without a new attack to match the type of the new chord. Pitch Shift to Root The pitch of the note will bend without a new attack to match the root of the new chord. Retrigger The note is retriggered with a new attack at a new pitch corresponding to the next chord. Retrigger To Root The note is retriggered with a new attack at the root note of the next chord. However, the octave of the new note remains the same. 118 CVP-205/203 Adjust the Volume Balance and Changing Voices — Mixing Console Set up just like a real mixing console, this display gives you comprehensive control over the sound. METRONOME POWER ON OFF START STOP SONG EXTRA TRACKS (STYLE) TRACK 2 (L) LCD CONTRAST TRACK 1 (R) BACK MENU TOP START / STOP REW FF REPEAT HELP A FUNCTION TEMPO TRANSPOSE TAP TEMPO MIN MAX RESET BREAK INTRO RESET ENDING / rit. MAIN A B C DIGITAL STUDIO SOUND CREATOR STYLE AUTO FILLIN F VARIATION HARMONY / ECHO MONO LEFT HOLD ORGAN & ACCORDION PERCUSSION GUITAR BASS STRINGS CHOIR & PAD SYNTH. XG VOICE PART ON / OFF B G LAYER C H LEFT D I BRASS USER ENTER SYNC.START NEW SONG FADE IN / OUT ACMP DSP E.PIANO WOODWIND VOICE PIANO & HARPSI. GUIDE MASTER VOLUME VOICE EFFECT REVERB NEXT DEMO REC SYNC.STOP SYNC.START START / STOP DIGITAL RECORDING MIXING CONSOLE D ONE TOUCH SETTING MUSIC FINDER 1 2 3 4 J E DATA ENTRY BALANCE PIANO REGISTRATION MEMORY FREEZE 1 2 3 4 5 6 7 8 Mixing Console This set of controls lets you adjust the balance of the voices and their stereo position, as well as the amount of effect that is applied to each voice. MEMORY PART CHANNEL OTS LINK ON / OFF PART MIXING CONSOLE DIRECT ACCESS 1 2 3 4 5 6 7 8 EXIT PART You can call up additional basic mixing controls by using the [BALANCE] button and the [CHANNEL ON/OFF] button (page 62). Operation 1 MIXING CONSOLE PART From the MIXING CONSOLE display, press the button repeatedly until the desired display is called up. Each press of the button switches among the displays listed below. PANEL PART Includes the keyboard-played parts (Main/ Layer, Left), accompaniment parts, song, microphone input (CVP-205 only) STYLE PART Accompaniment parts SONG CH 1 - 8 Channels 1 - 8 of song playback SONG CH 9 -16 Channels 9 - 16 of song playback 2 Select the other Mixing Console pages by using the [BACK]/ [NEXT] buttons and set the desired parameters. For information on the various parameters and settings and how to use them, refer to the explanations starting on page 120. You can quickly and easily set all parts to the same value for the same parameter (except for the VOICE parameter). Simultaneously hold down the [A] [J] button that corresponds to the parameter you want to change and use the [1] [8] buttons or the [DATA ENTRY] dial to change the value. n For details on parameters related to the Sound Creator, see page 89. END Close the Mixing Console display by pressing the [EXIT] button. ■ About the parameters • VOL/VOICE (Volume/Voice) (page 120) This contains settings related to the volume and voice of each part/channel. Here you can also enable the Auto Revoice feature — which automatically plays XG-compatible songs (page 152) with the rich and dynamic voices that are exclusive to the CVP-205/203. This gives you much more authentic and realistic instrument sounds for your song playback. • FILTER (page 121) These controls affect the tone quality of the voice, letting you add power, punch, or brightness to the sound. • TUNE (page 121) These give you various tuning controls. • EFFECT (page 122) These control the amount of effect applied to the sound. CVP-205/203 119 Adjust the Volume Balance and Changing Voices — Mixing Console Setting the Level Balance and Voice — Volume/Voice The operations for this page apply to step 2 of the procedure on page 119. 1 Use these to select the VOICE, PANPOT, or VOLUME parameter rows. Set this to ON to enable automatic replacement of the XG voices (in XG song data) with the special voices of the CVP-205/203. To use the normal XG voice set, turn this off. DIGITAL STUDIO SOUND CREATOR DIGITAL RECORDING MIXING CONSOLE BALANCE PART CHANNEL ON / OFF Allows you to select the specific voice to be replaced. PART Each press of this button switches among the various parts/channels. These let you select the voice of each part, and adjust the panpot and volume. VOICE Calls up the VOICE display, from which you can select the desired voice (page 55). When the Style/Song part is selected, User voices cannot be selected. PANPOT Determines the stereo position of the selected voice or track. A setting of 0 pans the sound hard left, while 64 is at center, and 127 is at hard right. VOLUME Determines the level of each channel, giving you fine control over the balance of all the parts. ALL REVOICE Replaces all of the replaceable XG voices with the rich and authentic voices of the CVP-205/203. 2 PIANO REVOICE Replaces only the piano voices. BASIC REVOICE Replaces only the recommended voices that are suitable for playing back the song. ALL NO REVOICE All the voices are returned to the original XG voices. Selects the XG voices to be replaced (voices usually used when playing back) 120 CVP-205/203 Executes the settings and closes the Auto Revoice Setup display. Selects the voices used to replace the XG voices (when SONG AUTO REVOICE is set to ON). Closes the Auto Revoice Setup screen without executing the settings. When playing GM song data, channel 10 (in the SONG CH 9 - 16 page) can only be used for a Drum Kit voice. When changing the rhythm/ percussion voices (drum kits, etc.) of the accompaniment style and song from the VOICE parameter, the detailed settings related to the drum voice are reset, and in some cases you may be unable to restore the original sound. In the case of song playback, you can restore the original sound by returning to the beginning of the song and playing back from that point. In the case of accompaniment style play, you can restore the original sound by selecting the same style again. PIANO and BASIC can be called up simultaneously. Keep in mind that using the Revoice function may result in unnatural or unexpected sound, depending on the particular song data. Adjust the Volume Balance and Changing Voices — Mixing Console Changing the Tone of the Voice — Filter The operations for this page apply to step 2 of the procedure on page 119. Switches between the HARMONIC and BRIGHTNESS parameters. For details about the Filter, see page 91. n When a Natural voice is selected, Harmonic and Brightness cannot be changed. DIGITAL STUDIO n Be careful with these controls. Depending on the selected voice, extreme settings may result in noise or distortion. SOUND CREATOR DIGITAL RECORDING MIXING CONSOLE BALANCE PART CHANNEL ON / OFF PART Each press of this button switches among the various parts/ channels. HARMONIC .........Allows you to adjust the resonance effect (see “Harmonic Content” on page 91). BRIGHTNESS .....Determines the brightness of the sound by adjusting the cutoff frequency (page 91). Changing Pitch-related Settings — Tune The operations for this page apply to step 2 of the procedure on page 119. Switches among the available parameters: PORTAMENTO TIME, PITCH BEND RANGE, OCTAVE, and TUNING. Portamento is used to create a smooth transition in pitch from one note to the next. When a Natural voice is selected, Portamento Time cannot be changed. Refer to the explanation below. These increase/decrease (transpose) the pitch in semitone units. MASTER ... Transposes both the pitch of the keyboard and that of the song playback. SONG........ Transposes the pitch of the song playback. KBD .......... Transposes the pitch of the keyboard. PORTAMENTO TIME ............When the part is set to Mono (page 59, 90), this determines the Portamento time. The higher the value, the longer the time it takes for the pitch to change. Portamento is only applied when you play legato (playing the next note before releasing the previous one). PITCH BEND RANGE ...........When the Pitch Bend or Glide effect is assigned to the pedal, this determines the range of the pitch change in semitones. OCTAVE................................Determines the range of the pitch change in octaves, over two octaves up or down. TUNING...............................Determines the pitch of the instrument. CVP-205/203 121 Adjust the Volume Balance and Changing Voices — Mixing Console Adjusting the Effects The operations for this page apply to step 2 of the procedure on page 119. 1 Indicates the type name for each effect block. Press this to edit and store the effect (page 122, 123). DIGITAL STUDIO SOUND CREATOR DIGITAL RECORDING MIXING CONSOLE BALANCE PART CHANNEL ON / OFF PART Switches among the Each press of this effect sections: button switches REVERB, CHORUS, among the various and DSP. parts/channels. Determines the amount of effect that is applied to each part. For more information about the characteristics of each effect, see the Effect Block list on page 123. 2 When the BLOCK parameter is set to REVERB1, CHORUS1, or DSP1, press this to call up the display from which you can change the detailed settings for the effects. These determine the effect block and let you assign the effect. BLOCK............ Determines the effect block (group of similar or related effects). PART ............... Determines the part to which the Insertion effect is applied. It is effective only when the block is set to “DSP1” and the CONNECTION parameter is set to “Insertion” (page 123). CATEGORY..... The various effect programs (in Type below) are grouped into categories. This parameter may not be available depending on the selected block. TYPE ............... Determines the type of effect that is assigned to the selected effect block. The actual effect types that are available may differ depending on the selected block. 122 CVP-205/203 There are three effect sections: Reverb, Chorus, and DSP (which contains a variety of effect types). These are available independently for the Natural voices and Regular voices. For details, refer to the Effect Block list (page 123). Adjust the Volume Balance and Changing Voices — Mixing Console 3 Calls up the display for storing the effect. This parameter cannot be set when BLOCK is set to “REVERB2,” “CHORUS2,” or “DSP2” (or “BRILLIANCE”; CVP-205 only). Determines the level of the effect (return level). This is not available when BLOCK is set to “DSP1,” PARAMETER is set to “CONNECTION,” and VALUE is set to “Insertion.” Switches between the upper/lower parameters. For the lower parameter, the depth can be changed when the [VARIATION] button is on. Determines the value of the selected parameter. Determines the effect parameter to be adjusted. Determines the effect block. Determines the effect category. Determines the effect type. 4 Calls up the display for naming the User Effect (page 46). Keep in mind that in some cases noise may result if you adjust the effect parameters while playing the instrument. Stores the effect settings you made above to a User Effect location (SYSTEM) for future recall. To call up the effect, select USER from the CATEGORY parameter and select the desired effect from the TYPE parameter. Select the destination to which the effect is to be stored. The number of memory spaces available for the destination differs for each block (refer to the chart below). Effect Block Block Parts REVERB 1 (for Regular Voices) All parts REVERB 2 (for Natural Voices) All parts except microphone (MIC) CHORUS 1 (for Regular Voices) All parts CHORUS 2 (for Natural Voices) All parts except microphone (MIC) DSP 1 (for Regular Voices) Main, Layer, Left, Song (Ch. 1 - 16), MIC DSP 2 (for Natural Voices) All parts except microphone (MIC) BRILLIANCE (CVP-205 only) All parts except microphone (MIC) (for Natural Voices) Characteristics Reproduces the warm ambience of playing in a concert hall or jazz club. Produces a rich “fat” sound as if several parts are being played simultaneously. In addition to reverb and chorus effects, this section features a variety of special effects, including distortion. Changes the brightness and clarity of the sound. Number of User Effect 3 — 3 — 3 — — CVP-205/203 123 Adjust the Volume Balance and Changing Voices — Mixing Console Effect Structure The CVP-205/203 features the following digital effect systems, which can be applied independently for the Natural voices (page 89) and the Regular voices (page 89). The effect type, depth, and various parameters can be set with the panel controls. • Reverb .......... Normally the settings that fit the selected style are called up. For most of the Natural voices, settings that fit the voice are called up. • Chorus.......... Normally the settings that fit the selected style are called up. For most of the Natural voices, settings that fit the voice are called up. • DSP .............. Normally the settings which fit the selected voice are called up. Variation (settings in which the expression of the effect is changed) is prepared for each type, and it can be turned ON/OFF by the [VARIATION] button on the panel. When the Natural voice is selected, the [VARIATION] button does not work. The illustration below shows how the various effect blocks are set up and traces the signal flow for the send/return controls set on the CVP-205/203. For Regular Voices (REVERB1, CHORUS1, DSP1) For Natural Voices (REVERB2, CHORUS2, DSP2) When DSP is set as an Insertion effect (here, PART is set to MAIN), it is put here in the signal flow. (For Natural voices, DSP can only be used as a System effect.) Dry MAIN VOICE DSP DRY LINE Reverb Return REVERB Rev Send Cho Send DSP Send Dry LAYER VOICE Rev Send Cho Send DSP Send Chorus Return CHORUS Dry LEFT VOICE (CVP-205 Natural Voices only) Rev Send Cho Send DSP Send MIC (CVP-205 only) Dry Rev Send Cho Send DSP Send Dry STYLE/SONG (each channel) Rev Send Cho Send DSP Return DSP Send DSP When DSP is set as a System effect, it is put here in the signal flow. (For Natural voices, DSP can only be used as a System effect.) 124 CVP-205/203 BRILLIANCE OUT Making Global and Other Important Settings — Function The Function mode gives you access to various advanced functions related to the instrument as a whole. These sophisticated functions let you customize the Clavinova to your own musical needs and preferences. METRONOME POWER ON OFF START STOP SONG EXTRA TRACKS (STYLE) TRACK 2 (L) LCD CONTRAST TRACK 1 (R) BACK MENU TOP START / STOP REW FF REPEAT HELP FUNCTION TEMPO DIGITAL STUDIO TRANSPOSE TAP TEMPO SOUND CREATOR RESET INTRO ENDING / rit. MAIN A B G LAYER C H LEFT HARMONY / ECHO MONO LEFT HOLD PERCUSSION GUITAR BASS STRINGS CHOIR & PAD SYNTH. XG ON / OFF BRASS WOODWIND USER ENTER B C SYNC.STOP SYNC.START START / STOP D 1 2 3 4 J E MIXING CONSOLE ONE TOUCH SETTING MUSIC FINDER I D DIGITAL RECORDING RESET STYLE BREAK F MENU MAX AUTO FILLIN VARIATION ORGAN & ACCORDION VOICE PART A SYNC.START NEW SONG FADE IN / OUT ACMP DSP E.PIANO VOICE PIANO & HARPSI. GUIDE MASTER VOLUME MIN VOICE EFFECT REVERB NEXT DEMO REC DATA ENTRY BALANCE PIANO REGISTRATION MEMORY FREEZE 1 2 3 4 5 6 7 8 MEMORY PART CHANNEL OTS LINK ON / OFF PART DIRECT ACCESS 1 2 3 4 5 6 7 8 EXIT FUNCTION Operation 1 MENU DEMO 2 Select the desired function. HELP FUNCTION 3 Set the parameters of the selected function. The operations for each function are covered in the following explanations. END To return to the previous display, press the [EXIT] button. Adjusting the Pitch and Tuning — Master Tune and Scale Tune ■ Master Tune (page 127) This allows you to make fine adjustments to the overall pitch of the instrument — letting you accurately match the tuning with that of other instruments. ■ Scale Tune (page 127) This determines the particular tuning system (or temperament) for the instrument. This is especially useful for playing period pieces, to match the tuning system used during specific musical eras. Setting Song-related Parameters — Song Settings (page 129) These allow you to set parameters related to song playback as well as the practice function types. Setting Auto Accompaniment-related Parameters — Style Setting, Split Point, and Chord Fingering ■ Style Setting / Split Point (page 130) These determine the auto accompaniment-related settings, and let you set the split point. ■ Chord Fingering (page 131) This determines the method for playing/indicating chords when using the auto accompaniment features. You can even check how to play the chord, since the individual notes are indicated in the display. CVP-205/203 125 Making Global and Other Important Settings — Function Making Settings for the Pedals and Keyboard — Controller ■ Pedal (page 131) These settings determine how the connected pedals (including foot controllers and footswitches) are used. They can be assigned to a variety of functions, letting you control operations with your feet — such as turning the accompaniment style on/off, or triggering Fill In patterns. ■ Keyboard / Panel (page 133) These settings determine the touch sensitivity of the keyboard (how touch affects volume), and let you independently transpose the keyboard, song data, and the entire instrument. Setting the Registration Sequence, Freeze, and Voice Set ■ Registration Sequence (page 134) This determines the order in which the Registration Memory presets (1 - 8) are called up — by using the [BACK][NEXT] buttons or the pedal. ■ Freeze (page 134) This lets you specify the settings you want to be maintained or left unchanged, even when changing Registration Memory presets. ■ Voice Set (page 135) This lets you determine whether certain voice-related settings (such as Effects, EQ, Harmony, etc.) are automatically called up or not when you select a voice. Setting Harmony and Echo (page 135) These let you set the type of Harmony or Echo effect applied to the keyboard-played voices, as well as the amount of effect. Showing the Clavinova Display on a TV — Video Out (CVP-205 only) (page 136) These settings determine the display characteristics when outputting the CVP-205’s display contents to a TV monitor (connected to the VIDEO OUT terminal). You can set the size and color of the displayed characters, as well as the color of the display background. 126 CVP-205/203 Making MIDI Settings ■ System (page 137) These determine various system messages settings (such as Clock, Start/Stop, System Exclusive), as well as Local Control on/off. ■ Transmit (page 138) This determines how playback data is sent to connected MIDI devices — i.e., which parts are assigned to which MIDI Transmit channels. This also lets you specify the type of data to be transmitted over each channel. ■ Receive (page 139) This determines how the parts of the CVP-205/203 respond to data from connected MIDI devices — i.e., which parts are assigned to which MIDI Receive channels. This also lets you specify the type of data to be received over each channel. ■ Root (page 139) This determines the channel(s) recognized for the root notes, for use with the auto accompaniment. ■ Chord Detect (page 139) This determines the channel(s) recognized for the chords, for use with the auto accompaniment. Other Settings — Utility ■ Config 1 (page 140) This page contains settings for Fade In/Out, Metronome, Parameter Lock, and the Tap sound. ■ Config 2 (page 141) From this page, you can adjust the display, make speaker settings, and change the voice number indication. ■ Disk (page 142) From this page, you can format disks, and copy from disk to disk. ■ Owner (page 143) From this page, you can set the language of the instrument, and input your own name — which is shown automatically every time the power is turned on. ■ System Reset (page 143) This function restores the CVP-205/203 to its original factory settings. You can also specify which types of settings are to be restored, as well as store your own original settings for future recall. Making Global and Other Important Settings — Function Fine Tuning the Pitch/Selecting a Scale — Master Tune/Scale Tune The explanations here apply to step #3 of the procedure on page 125. Tuning the Overall Pitch — Master Tune Hz (Hertz) This unit of measurement refers to the frequency of a sound, and represents the number of times a sound wave vibrates in a second. n The Tune function does not affect the Drum Kit or SFX Kit voices. Determines the overall pitch of the CVP-205/ 203, from 414.8 - 466.8 Hz. Press the 4 or 5 [▲▼] buttons simultaneously to instantly reset the value to the factory setting of 440.0 Hz. Selecting a Scale — Scale Tune The current tuning of each note is shown above or below the corresponding key. Cent A unit of pitch equal to 1/100 of a semitone (100 cents = 1 semitone). n You can register your original scale tunings to a REGISTRATION MEMORY button. To do this, checkmark “SCALE” in the REGISTRATION MEMORY display (page 85). Determines the base note for each scale. When the base note is changed, the pitch of the keyboard is transposed, yet maintains the original pitch relationship between the notes. Determines the Scale (page 128). Determines the fine tuning of the selected note in 1cent steps. Press the 5 or 6 [▲▼] buttons simultaneously to instantly reset the value to the factory setting. Determines the note to be tuned and the amount of tuning. The tuning range is from “-64” through “0” to “+63.” Each increment equals one cent (one “cent” is one hundredth of a semitone). CVP-205/203 127 Making Global and Other Important Settings — Function Scale ■ Equal Temperament The pitch range of each octave is divided equally into twelve parts, with each half-step evenly spaced in pitch. This is the most commonly used tuning in music today. ■ Pure Major/Pure Minor These tunings preserve the pure mathematical intervals of each scale, especially for triad chords (root, third, fifth). You can hear this best in actual vocal harmonies — such as choirs and acapella singing. ■ Pythagorean This scale was devised by the famous Greek philosopher and is created from a series of perfect fifths, which are collapsed into a single octave. The 3rd in this tuning are slightly unstable, but the 4th and 5th are beautiful and suitable for some leads. ■ Mean-Tone This scale was created as an improvement on the Pythagorean scale, by making the major third interval more “in tune.” It was especially popular from the 16th century to the 18th century. Handel, among others, used this scale. ■ Werckmeister/Kirnberger This composite scale combines the Werckmeister and Kirnberger systems, which were themselves improvements on the mean-tone and Pythagorean scales. The main feature of this scale is that each key has its own unique character. The scale was used extensively during the time of Bach and Beethoven, and even now it is often used when performing period music on the harpsichord. ■ Arabic Use these tunings when playing Arabic music. Pitch settings for each scale (in cents; example scale of C) The values shown in this chart are actually rounded off to the nearest whole number for use on the instrument. C C D E E F F G A A B B 128 Equal Temperament 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 Pure Major 0.0 -29.7 3.9 15.6 -14.1 -2.3 -9.4 2.3 -27.3 -15.6 18.0 -11.7 Pure Minor 0.0 33.6 3.9 15.6 -14.1 -2.3 31.3 2.3 14.1 -15.6 18.0 -11.7 Pythagorean 0.0 14.1 3.9 -6.3 7.8 -2.3 11.7 2.3 15.6 6.3 -3.9 10.2 Mean-Tone 0.0 -24.2 -7.0 10.2 -14.1 3.1 -20.3 -3.1 -27.3 -10.2 7.0 -17.2 Werckmeister 0.0 -10.2 -7.8 -6.3 -10.2 -2.3 -11.7 -3.9 -7.8 -11.7 -3.9 -7.8 Kirnberger 0.0 -10.2 -7.0 -6.3 -14.1 -2.3 -10.2 -3.1 -7.8 -10.2 -3.9 -11.7 Arabic1 0.0 0 -50.0 0.0 0.0 0.0 0.0 0.0 0.0 -50.0 0.0 0.0 Arabic2 0.0 0 0.0 0.0 -50.0 0.0 0.0 0.0 0.0 0.0 0.0 -50.0 CVP-205/203 Making Global and Other Important Settings — Function Setting Song-related Parameters — Song Settings The explanations here apply to step #3 of the procedure on page 125. Allows you to play back all songs from the same folder continuously. Turns Quick Start on/off (see note). Determines the Guide method. Turns guide lamps ON or OFF. Determines the timing for the guide lamps. JUST ........ The guide lamps light precisely at the moment you should play. NEXT ........ The guide lamps light just before the moment you should play. If you miss the proper timing, the guide lamps flash. Determines the MIDI channel assigned to the [TRACK2] button. Determines the MIDI channel assigned to the [TRACK1] button. Quick Start On some commercially available song data, certain settings related to the song (such as voice selection, volume, etc.) are recorded to the first measure, before the actual note data. When Quick Start is set to “ON,” the CVP-205/203 reads all initial non-note data of the song at the highest possible speed, then automatically slows down to the appropriate tempo at the first note. This allows you to start playback as quickly as possible, with a minimum pause for reading of data. n Determines whether the Phrase Mark Repeat function for the song is on or off. When this is on, you can repeatedly play back a specified phrase (selection of measures) of the song. The method for setting a phrase mark is the same as that in the SONG POSITION display (page 77). Determines the language of the displayed lyrics. When this is set to “AUTO,” the language defaults to that of the song data. When not set to “AUTO,” the language defaults to Japanese, when the internal setting (page 143) is “JAPANESE”; for all other languages, this is set to “INTERNATIONAL.” When set to “ON,” this automatically sets the proper Track 1 and Track 2 channels for use with the practice functions. Normally, this should be set to “ON.” Channel Refers to the MIDI channel (page 150). The channels are assigned as follows: Song 1 - 16 Accompaniment Style 9 - 16 n The guide lamps light in response to song channel assigned to Tracks 1 and 2, as well as chord data (when contained in the song). Normally, you can leave the AUTO SET CH function set to ON, and the song channel will automatically be set. If the results aren’t satisfactory, you’ll need to match the Channel Setting "TRK1 CH" and "TRK2 CH" parameters to the appropriate right- and left-hand parts. n Phrase Mark This data specifies a certain location in the song data. In the included “Music Software Collection” songs (CVP-203 only), these are indicated by numbers (1, 2, etc.) in the score. CVP-205/203 129 Making Global and Other Important Settings — Function Setting Auto Accompaniment-related Parameters — Style Setting, Split Point, and Chord Fingering The explanations here apply to step #3 of the procedure on page 125. Setting Auto Accompaniment-related Parameters — Style Setting and Split Point These select the part to which the split point About Section Set setting is applied: accompaniment, left-hand When any of the Main A-D range, or both. Press the desired key for the split sections is not included in point while holding down one of these buttons. the accompaniment style The pressed key is included in the range for the data, the nearest section is Auto Accompaniment section of the keyboard automatically selected. For (ACMP) or the left-hand range (LEFT). example, when Main D is not A+L (ACMP + LEFT) contained in the selected Allows you to simultaneously set the split accompaniment style, Main point for both the left-hand range and the C will be called up. Auto Accompaniment section of the keyboard. L (LEFT) Allows you to set the split point for the left-hand range of the keyboard. A (ACMP) Allows you to set the split point for the Auto Accompaniment section of the keyboard. Determines the split points for the auto accompaniment (ACMP) and the lefthand range (LEFT). The same value can be set for both or for each independently, using buttons [F], [G], and [H] (see above). You can use these buttons by themselves to set the split point value. Determines the default section that is automatically called up when selecting different accompaniment styles (when accompaniment is stopped). Turns touch response for the accompaniment on/off. When this is set to “ON,” the accompaniment volume changes in response to your playing strength (in the Auto Accompaniment section of the keyboard). The CVP-205/203 lets you automatically enable Sync Stop (page 66) simply by quickly pressing/releasing keys in the Auto Accompaniment section of the keyboard. This parameter lets you set the length of the key-hold time. This applies to the OTS Link function, in which One Touch Settings are automatically called up with changes in the section. This determines the timing in which the One Touch Settings change with the section. (The [OTS LINK] button must be on.) Real Time One Touch Setting is immediately called up when you press a section button. Next Bar One Touch Setting is called up at the next measure, after you press a section button. Split point can be set in the MAIN display. Turns the Stop Accompaniment (ACMP) function on/off. When this is set to “ON,” you can play the chord and bass sounds of the accompaniment by playing chords — even when the accompaniment style is not playing back. About Split Point Split point is the position on keyboard that separates the Auto Accompaniment section (ACMP) and left-hand section (LEFT) from the right-hand section (MAIN). The LEFT split point cannot be set lower than the ACMP split point, and the ACMP split point cannot be set higher than the LEFT split point. Split point (A) Auto Accompaniment section Right-hand Left-hand section section Split point (A) + (L) Auto Accompaniment section + Left-hand section 130 CVP-205/203 Split point (L) Right-hand section Making Global and Other Important Settings — Function Setting the Fingering Method — Chord Fingering This determines how the notes you play on the keyboard indicate or play the chords of the accompaniment. To learn how to play certain chords, use the convenient Chord Tutor function (see note below). Indicates the note that belongs to a chord. Some notes can be omitted. The chord name is indicated next to “CHORD NAME.” ...Required ...Can be omitted ...Either note can be omitted ...Can be omitted when the note indicated by is omitted Determines the fingering type (page 63). This lets you change the chord type. Indicates the note that belongs to a chord in the music. The chord indication in the display applies to the Fingered method, regardless if another method is actually selected. Chord Tutor The Chord Tutor feature is essentially an electronic “chord book” that shows you appropriate fingerings for chords; it is useful when you want to play certain chords. Simply specify the desired chord via the [6▲▼] - [8▲▼] buttons, and the fingerings for the Fingered method are indicated in the display. This lets you change the root note from the chord. Making Settings for the Pedals and Keyboard — Controller The explanations here apply to step #3 of the procedure on page 125. Making Settings for the Pedals Determines the particular pedal to which a function is to be assigned. Pedal on/off operation may differ depending on the particular pedal you’ve connected to the [AUX PEDAL] jack. For example, pressing down on one pedal may turn the selected function on, while pressing a different make/brand of pedal may turn the function off. If necessary, use this setting to reverse the operation. Determines the function to be assigned to the selected pedal. Any one of the available functions can be assigned to each pedal. For information on the assignable functions, see “Pedal-controllable Functions” on page 132. If necessary, you can turn the corresponding part ON/ OFF or set the control depth (see the next page). CVP-205/203 131 Making Global and Other Important Settings — Function Pedal-controllable Functions VOLUME* Allows you to use a foot controller (AUX pedal only) to control the volume. SUSTAIN When the pedal is pressed notes played have a long sustain. Releasing the pedal immediately stops (damps) any sustained notes. SOSTENUTO If you press and hold the pedal here, only the first note will be sustained (the note that you played and held when pressing the pedal). This makes it possible to sustain a chord, for example, while other notes are played staccato. SOFT Pressing the pedal subtly reduces the volume and slightly changes the timbre of notes played. It only applies to certain voices — PIANO, for example. GLIDE When the pedal is pressed the pitch changes, and then back to normal pitch when the pedal is released. PORTAMENTO The portamento effect (a smooth slide between notes) can be produced while the pedal is pressed. Portamento is produced when notes are played legato style (i.e., a note is played while the preceding note is still held). The portamento time can be set via the Mixing Console display (page 121). It does not work for Natural voices. PITCHBEND* Bend notes up or down while pedal is pressed. This can only be set to the AUX pedal and the CVP-205’s damper pedal. MODULATION* Applies a vibrato effect to notes played on the keyboard. The depth of the effect increases while pedal is pressed. This does not work for the Natural voices. DSP VARIATION Same as the [VARIATION] button. This does not work for the Natural voices. VIBROTOR ON/OFF Turns the “VibRotor” effect type (page 122) on and off. This only works for the Natural voices. HARMONY/ECHO Same as the [HARMONY/ECHO] button. SCORE PAGE+ (CVP-205 only) While the song is stopped, you can turn to the previous score page (one page only). SCORE PAGE- (CVP-205 only) While the song is stopped, you can turn to the next score page (one page only). SONG START/STOP Same as the SONG [START/STOP] button. STYLE START/STOP Same as the STYLE [START/STOP] button. TAP TEMPO Same as the [TAP TEMPO] button. SYNCRO START Same as the [SYNC. START] button. SYNCRO STOP Same as the [SYNC. STOP] button. INTRO Same as the [INTRO] button. MAIN A Same as the [MAIN A] button. MAIN B Same as the [MAIN B] button. MAIN C Same as the [MAIN C] button. MAIN D Same as the [MAIN D] button. FILL DOWN A fill-in plays, automatically followed by the Main section of the button on the immediate left. FILL SELF Fill-in starts playing. BREAK Break starts playing. FILL UP A fill-in plays, automatically followed by the Main section of the button on the immediate right. ENDING Same as the [ENDING/rit.] button. FADE IN/OUT Same as the [FADE IN/OUT] button. FING/ON BASS The pedal alternately switches between the Fingered and On Bass modes (page 63). BASS HOLD While the pedal is pressed, the Accompaniment Style bass note will be held even if the chord is changed. If the fingering is set to “FULL KEYBOARD,” the function does not work. PERCUSSION The pedal plays a percussion instrument selected by the [4▲▼] - [8▲▼] buttons. You can use the keyboard to select the desired percussion instrument. LAYER ON/OFF Same as the [LAYER] button. LEFT ON/OFF Same as the [LEFT] button. OTS+ Calls up the next One Touch Setting. OTS- Calls up the previous One Touch Setting. * For best results, use the optional Yamaha FC7 Foot Controller. The parameters below correspond to buttons [2▲▼] - [8▲▼], and their availability depends on the selected control Type. For example, if SUSTAIN is selected as the Type, the parameters “HALF PEDAL POINT”, “MAIN”, “LAYER” and “LEFT” automatically appear in the display. SONG, STYLE, MIC (CVP-205 only), LEFT, LAYER, MAIN These specify the part(s) that will be affected by the pedal. HALF PEDAL POINT* You can specify how far down you should press on the right pedal until the damper effect (page 59) starts working. This can be set for certain kinds of pedals, such as the AUX pedal (YAMAHA FC7) or the CVP-205’s damper pedal. DEPTH Determines the depth of the left pedal effect, when SOFT is selected. This only works for the Natural voices. UP/DOWN When GLIDE or PITCH BEND is selected, this determines whether the pitch change goes up (is raised) or down (is lowered). RANGE When GLIDE or PITCH BEND is selected, this determines the range of the pitch change, in semitones. ON SPEED When GLIDE is selected, this determines the speed of the pitch change, when the pedal is pressed. OFF SPEED When GLIDE is selected, this determines the speed of the pitch change, when the pedal is released. KIT When PERCUSSION is assigned to the pedal, all available drum kits are shown here, letting you select the particular drum kit used for the pedal. PERCUSSION When PERCUSSION is assigned to the pedal, all sounds of the selected drum kit (in KIT above) are shown here. This determines the particular instrument sound assigned to the pedal. * For best results, use the optional Yamaha FC7 Foot Controller. 132 CVP-205/203 Making Global and Other Important Settings — Function Changing the Touch Sensitivity and Transpose — Keyboard/Panel Keyboard Touch The Touch feature lets you control the volume of the voices by your playing strength. These settings allow you to customize the keyboard’s touch response (sensitivity) to your personal playing preferences. HARD 2 Requires strong playing to produce high volume. Best for players with a heavy touch. HARD 1 Requires moderately strong playing for higher volume. NORMAL Standard touch response. Determines the Touch sensitivity setting (refer to the table at right). Determines the fixed volume level when Touch is set to “OFF.” Determines whether touch is on or not for the corresponding parts. SOFT 1 Produces high volume with moderate playing strength. SOFT 2 Produces relatively high volume even with light playing strength. Best for players with a light touch. The TOUCH setting affects all voices globally. Keep in mind that you can set each voice to a different touch sensitivity (TOUCH SENSE). For example, to play a pipe organ voice most authentically, you can set this so that the voice is not affected by touch (page 90). Transpose Assign This determines which aspect of the instrument is affected by the [TRANSPOSE] button. Transpose Allows you to shift the pitch of the keyboard-played voices, accompaniment style playback, and song data in semitone units. 1 Press one of the [TRANSPOSE] buttons. TRANSPOSE RESET KEYBOARD For this setting, Transpose affects the pitch of the keyboard-played voices (Main, Layer, and Left) and the accompaniment styles. SONG For this setting, Transpose affects only the pitch of the songs. MASTER For this setting, Transpose affects the pitch of the entire instrument (keyboard voices, accompaniment styles, and songs). The transpose function does not affect the Drum Kit or SFX Kit voices. 2 A TRANSPOSE pop-up window, selected via TRANSPOSE ASSIGN, appears. 3 Adjust the value by using the [TRANSPOSE] buttons. END Close the TRANSPOSE windows by pressing the [EXIT] button. • Selectively Transposing Keyboard/Song These settings can be used to match both the song and your keyboard performance to a certain key. For example, let’s say you wish to play and sing along with a certain recorded song. The song data is in F, but you feel most comfortable singing in D, and you are accustomed to playing the keyboard part in C. To match up the keys, keep the Master Transpose setting at “0,” set the Keyboard Transpose to “2,” and set Song Transpose to “-3.” This brings the keyboard part up in pitch and the song data down to your comfortable singing key. CVP-205/203 133 Making Global and Other Important Settings — Function Setting the Registration Sequence, Freeze, and Voice Set The explanations here apply to step #3 of the procedure on page 125. Specifying the Order for Calling Up Registration Memory Presets — Registration Sequence You can save your custom panel settings to the Registration Memory presets, and call them up by pressing the appropriate REGISTRATION MEMORY buttons [1] - [8]. The convenient Registration Sequence function lets you call up the presets in any order you specify, by simply using the [BACK]/[NEXT] buttons or the pedal as you play. Determines which pedal is used to advance (increment) through the sequence. Indicates the file name of the selected Registration Memory bank. Determines which pedal is used to reverse (decrement) through the sequence. Setting Registration Sequence Enable to “ON” overrides any other Pedal settings (for pedals assigned to “Regist (+) Pedal” and “Regist (-) Pedal” here). These include the pedal settings on page 131, and in Voice Set on page 135. n Determines how Registration Sequence behaves when reaching the end of the sequence. Stop Pressing the [NEXT] button or the “advance” pedal has no effect. The sequence is “stopped.” Top The sequence starts again at the beginning. Next Bank The sequence automatically moves to the beginning of the next Registration Memory bank in the same folder. Indicates the Registration Memory preset numbers, in the order of the current Registration Sequence. These move the cursor position in the sequence. Turns the Registration Sequence function on/off. When this is set to “ON,” the programmed Registration Sequence is shown at the top right of the Main display, and you can step through the sequence in this display by using the [BACK]/[NEXT] buttons or the pedals. n When both “Regist (+) Pedal” and “Regist (-) Pedal” are set to the same pedal, “Regist (+) Pedal” takes priority. Deletes all Registration Memory numbers in the sequence. Deletes the number at the cursor position. Inserts the number of the currently selected Registration Memory preset immediately before the cursor position. Replaces the number at the cursor position with the currently selected Registration Memory number. END When both “Regist (+) Pedal” and “Regist (-) Pedal” are set to “OFF,” the pedals cannot be used to step through the Registration Sequence; only the [BACK]/ [NEXT] buttons can be used in the MAIN display. Execute the settings by pressing the [EXIT] button. Registration Sequence data is included as part of the Registration Memory bank file. To save your newly programmed Registration Sequence, store the current Registration Memory bank file (page 39, 45). Any Registration Sequence data is lost when changing Registration Memory banks, unless you’ve stored it with the Registration Memory bank file. Maintaining Panel Settings — Freeze This lets you specify the settings you want to be maintained or left unchanged, even when changing Registration Memory presets. For details, see page 87. 134 CVP-205/203 Making Global and Other Important Settings — Function Changing the Automatically Selected Voice Settings — Voice Set When changing voices (selecting a voice file), the settings best matching the voice — the same as those set in the Sound Creator — are always and automatically called up. From this page , you can set the on/off status for each part. For example, each of the preset voices has its own LEFT PEDAL setting; however, even changing voices will not change the LEFT PEDAL setting, if it is set to "OFF" in this page. Normally, these should all be set to "ON." Use these to select the desired part. Harmony/Echo and Left pedal assignment cannot be set for the Layer and Left parts. These determine whether the corresponding voice-related settings (Voice selection, Effects, Harmony/Echo, and left pedal assignment) are automatically called up or not when you select a voice. These settings can be turned on or off independently for each part. Setting Harmony and Echo The explanations here apply to step #3 of the procedure on page 125. Determines the Harmony type. For details, see page 136. Determines the level of the Harmony effect. Determines the speed of the Echo, Tremolo, and Trill effects. This parameter is only available when Echo, Tremolo, or Trill is selected in Type above. Determines the lowest velocity value at which the harmony note will sound. This allows you to selectively apply the harmony by your playing strength, letting you create harmony accents in the melody. The harmony effect is applied when you play the key strongly (above the set value). When this is set to “ON,” the Harmony effect is applied only to the note that belongs to a chord played in the Auto Accompaniment section of the keyboard. This parameter is not available when Multi Assign, Echo, Tremolo, or Trill is selected in Type above. This lets you assign the Harmony effect to various parts. For details, see page 136. CVP-205/203 135 Making Global and Other Important Settings — Function About the Harmony Types When a normal Harmony type (“Standard Duet” through “Strum”) is selected Split point Harmony notes (based on the chord and the selected type) are automatically added to the melody played to the right of the split point. Chords played to the left of the split point control the harmony. When “Multi Assign” is selected Multi Assign automatically assigns notes played simultaneously on the right-hand section of the keyboard to separate parts (voices). For example, if you play two consecutive notes, the first is played by the Main voice and the second by the Layer voice. When “Echo” is selected An echo effect is applied to the note played on the keyboard, in time with the currently set tempo. When “Tremolo” is selected A tremolo effect is applied to the note played on the keyboard, in time with the currently set tempo. When “Trill” is selected Two notes held on the keyboard are played alternately, in time with the currently set tempo. About the Harmony Assignments Multi This automatically assigns the 1st, 2nd, 3rd, and 4th added harmony notes to different parts (voices). For example, if the Main and Layer parts are turned on and the “Standard Duet” type is selected, the note you play on the keyboard will be played by the Main voice, and the added harmony note will be played by the Layer voice. Main Harmony is applied only to the Main part. Layer Harmony is applied only to the Layer part. When the Layer part is turned off, Harmony is not applied. Showing the Clavinova Display on a TV — Video Out (CVP-205 only) The explanations here apply to step #3 of the procedure on page 125. Television VIDEO IN Set this to correspond to the standard used by your particular television/video equipment: NTSC or PAL. Set this to “SMALL” if the contents of the display do not fit in your monitor screen. VIDEO OUT Determines the background color of the display. Determines the colors of the characters displayed on the video screen. 136 CVP-205/203 • Occasionally some flashing parallel lines may appear in the television or video monitor. This does not necessarily indicate that the monitor is malfunctioning. You may be able to remedy the situation by changing the Character Color or Background Color parameters. For optimum results, also try adjusting the color settings on the monitor itself. • Avoid looking at the television or video monitor for prolonged periods of time since doing so could damage your eyesight. Take frequent breaks and focus your eyes on distant objects to avoid eyestrain. • Keep in mind that even after adjusting all settings as recommended here, the monitor you are using may not show the CVP-205’s display contents as expected (e.g., the display contents may not fit on the screen, the characters may not be completely clear, or the colors may be incorrect). Making Global and Other Important Settings — Function Setting the MIDI Parameters In this section, you can make MIDI-related settings for the instrument. These settings can be stored all together from the USER display, for future recall. For general information and details about MIDI, see “What is MIDI?” (page 148). The explanations here apply to step #3 of the procedure on page 125. 1 3 Select the desired template. Call up the User display and press this button to save the newly edited MIDI settings. Up to ten setups can be saved. END 2 Call up the Edit display, then select and set the desired functions/parameters. For details about each of the MIDI edit displays, see the following pages. Press the [EXIT] button to return to the previous display. Preset MIDI Templates (Factory Set) All Parts Transmit all parts including Main, Layer and Left. Master KBD The Clavinova functions as a master keyboard for controlling external tone generators or other devices. KBD & Style Transmit Upper and Lower keyboard play instead of the individual parts (Main/ Layer/Left). Song All Transmit channels are set to correspond to the Song channels 1-16. Use this to play the Clavinova song data with an external tone generator, or to record your entire performance to an external sequencer. Clock Ext. MIDI IN terminal receives MIDI clock and Clavinova synchronizes with a external MIDI device. MIDI Accord 1 An ideal setup for controlling the keyboard voice and accompaniment style with a MIDI accordion. MIDI Accord 2 Chord and bass buttons on a MIDI accordion control the accompaniment style, as well as play the chord and bass parts. MIDI Pedal 1 The MIDI pedal connected to MIDI IN terminal controls the bass note of the accompaniment. MIDI Pedal 2 The MIDI pedal connected to MIDI IN terminal plays the bass part. MIDI OFF MIDI signals are neither sent nor received. The saved settings can be named (page 42) or deleted (page 44) in the User page. Making Overall System Settings (Local Control, Clock, etc.) — System Call up the display as described in step 2 above. For editing the Local Control parameters. For editing the Clock, Transmit Clock, Receive Transpose, and Start/Stop parameters. For editing the Message Switch parameters. Local Control Turns the Local Control for each part on or off. When Local Control is set to “ON,” the keyboard of the CVP-205/203 controls its own (local) internal tone generator, allowing the internal voices to be played directly from the keyboard. If you set Local to “OFF,” the keyboard and controllers are internally disconnected from the CVP-205/203’s tone generator section so that no sound is output when you play the keyboard or use the controllers. For example, this allows you to use an external MIDI sequencer to play the CVP-205/203’s internal voices, and use the CVP-205/203 keyboard to record notes to the external sequencer and/or play an external tone generator. CVP-205/203 137 Making Global and Other Important Settings — Function Clock, Transmit Clock, Receive Transpose, Start/Stop ■ Clock Determines whether the CVP-205/203 is controlled by its own internal clock or a MIDI clock signal received from an external device. “INTERNAL” is the normal Clock setting when the CVP-205/203 is being used alone. If you are using the CVP-205/203 with an external sequencer, MIDI computer, or other MIDI device, and you want the CVP205/203 to be synchronized to the external device, set this function to “EXTERNAL.” In the latter case, the external device must be connected to the CVP-205/203 MIDI IN terminal, and must be transmitting an appropriate MIDI clock signal. ■ Transmit Clock Turns MIDI clock transmission on or off. When this is set to “OFF,” no MIDI clock or START/STOP data is transmitted. ■ Receive Transpose When this parameter is set to “OFF,” note data received by the CVP-205/203 is not transposed, and when it is set to “ON,” the received note data is transposed according to the current CVP-205/203 keyboard transpose (page 133) setting. ■ Start/Stop Determines whether incoming FA (start) and FC (stop) messages affect song or style playback. FA, FC MIDI messages for starting/stopping the song or style. The “FA” message corresponds to start, and “FC” corresponds to stop. Message Switch SYS/EX. Tx (TRANSMIT)..................... Turns MIDI transmission of MIDI system exclusive message data ON or OFF. SYS/EX. Rx (RECEIVE) ........................ Turns MIDI reception of MIDI exclusive data generated by external equipment ON or OFF. CHORD SYS/EX. Tx (TRANSMIT) ...... Turns MIDI transmission of MIDI chord exclusive data (chord detect — root and type) ON or OFF. CHORD SYS/EX. Rx (RECEIVE).......... Turns MIDI reception of MIDI chord exclusive data generated by external equipment ON or OFF. Transmitting MIDI Data — Transmit This determines which parts will send MIDI data and over which MIDI channel the data will be sent. Determines the channel for changing transmit settings. Determines the Part for the selected channel. The dots corresponding to each channel (1-16) flash briefly whenever any data is transmitted on the channel(s). Turns transmission of the specified data type on or off. See below for details on the data types. Data Types in the MIDI TRANSMIT/RECEIVE Display Note Messages which are generated when the keyboard is played. Each message includes a specific note number which corresponds to the key which is pressed, plus a velocity value based on how hard the key is played. Control Change (CC) Control change data includes pedal and any other controller data. Program Change (PC) Program change data corresponds to voice or “patch” numbers. Pitch Bend (PB) See page 132. After Touch (AT)* With this function, the Clavinova senses how much pressure you apply to the keys while playing, and uses that pressure to affect the sound in various ways, depending on the selected voice. This allows you to play with greater expressiveness and add effects with your playing technique. * Available in RECEIVE display only (page 139). 138 CVP-205/203 Making Global and Other Important Settings — Function Receiving MIDI Data — Receive This determines which parts will receive MIDI data and over which MIDI channel the data will be received. The MIDI IN/OUT terminals and Port A of the TO HOST terminal (Port A of the CBX driver) correspond to channels 1 - 16. Port B of the TO HOST terminal (Port B of the CBX driver) corresponds to channels 17 - 32. Determines the channel for changing receive settings. The dots corresponding to each channel (1 - 32) flash briefly whenever any data is received on the channel(s). Turns reception of the specified data type on or off. See page 138 for details on the data types. Determines the Part for the selected channel. See below for details about the receive parts. MIDI Receive Parts OFF No MIDI data is received. SONG Normally, the part receiving the MIDI data corresponds to the part/voice used in playing back the song data. Channels 1 - 16 correspond to song channels 1 - 16, respectively. MAIN The MAIN part is controlled by the MIDI data received on the corresponding channel. LAYER The LAYER part is controlled by the MIDI data received on the corresponding channel. LEFT The LEFT part is controlled by the MIDI data received on the corresponding channel. KEYBOARD MIDI note data received by the Clavinova plays the corresponding notes in the same way as if they are played on the keyboard. ACMP RHYTHM1-2 The received notes are used as the accompaniment RHYTHM 1 and RHYTHM 2 notes. ACMP BASS The received notes are used as the accompaniment BASS notes. ACMP CHORD1-2 The received notes are used as the accompaniment CHORD 1 and CHORD 2 notes. ACMP PAD The received notes are used as the accompaniment PAD notes. ACMP PHRASE1-2 The received notes are used as the accompaniment PHRASE 1 and PHRASE 2 notes. EXTRA PART1-5 There are five parts specially reserved for receiving and playing MIDI data. Normally, these parts are not used by the instrument itself. When these five channels are enabled, you can use the instrument as a 32-channel multi-timbral tone generator. Setting Root Note Channels — Root The note ON/OFF messages received at the channel(s) set to “ON” are recognized as the root notes in the accompaniment section. The root notes will be detected regardless of the accompaniment ON/OFF and split point settings. The MIDI IN/OUT terminals and Port A of the TO HOST terminal (Port A of the CBX driver) correspond to channels 1 - 16. Port B of the TO HOST terminal (Port B of the CBX driver) corresponds to channels 17 - 32. Selects the channels in groups of eight: 1 - 8, 9 - 16, 17 - 24, and 25 - 32, respectively. When several channels are simultaneously set to “ON,” the root note is detected from merged MIDI data received over the channels. Sets the desired channel to ON or OFF. Sets all channels to OFF. Setting Chord Channels — Chord Detect The note ON/OFF messages received at the channel(s) set to “ON” are recognized as the chord notes in the accompaniment section. The chords to be detected depend on the fingering type. The root notes will be detected regardless of the accompaniment ON/OFF and split point settings. The operation procedure is basically the same as that of the ROOT display above. CVP-205/203 139 Making Global and Other Important Settings — Function Other Settings — Utility The explanations here apply to step #3 of the procedure on page 125. Making Settings for Fade In/Out, Metronome, Parameter Lock, and Tap — CONFIG 1 Fade In Time, Fade Out Time, Fade Out Hold Time These determine how long it takes for the accompaniment style and song to fade in or fade out. Determines the time it takes for the volume to fade in, or go from minimum to maximum (range of 0 - 20.0 seconds). Determines the time it takes for the volume to fade out, or go from maximum to minimum (range of 0 - 20.0 seconds). Determines the time the volume is held at 0 following the fade out (range of 0 5.0 seconds). Metronome These let you make settings for the metronome-related parameters. Determines the level of the metronome sound. Determines which sound is used for the metronome. Bell Off ........................ Conventional metronome sound, with no bell. Bell On......................... Conventional metronome sound, with bell. English Voice .............. Count in English (One, Two, Three, Four) German Voice.............. Count in German (Eins, Zwei, Drei, Vier) Japanese Voice........... Count in Japanese (Ichi, Ni, San, Shi) French Voice ............... Count in French (Un, Deux, Trois, Quatre) Spanish Voice ............. Count in Spanish (Uno, Dos, Tres, Cuatro) 140 CVP-205/203 Determines the time signature of the metronome sound. When you start the song or accompaniment style, the values matching to them are automatically set. Making Global and Other Important Settings — Function Parameter Lock This function is used to “lock” the specified parameters so that they can only be changed directly via the panel controls — in other words, instead of via Registration Memory, One Touch Setting, Music Finder, or song and sequence data. Selects the desired parameter for locking/ unlocking. Determines whether the selected parameter is locked (checkmarked) or unlocked (empty). Tap Count This lets you change settings of the tap sound, used for the Tap Start function (page 52). Determines the particular sound used for the Tap Start function. Any drum or percussion sound in the Standard Kit (page 56) can be selected. Determines the level of the tap sound. Making Settings for the Display, Speaker System, and Voice Number Indication — CONFIG 2 HEADPHONE SW (SWITCH) Speaker sounds normally, but is cut off when headphones are inserted to the PHONES jack. ON Speaker sound is always on. OFF Speaker sound is off. Determines the brightness of the backlit display. Determines whether or not the voice bank and number are shown in the PRESET page of the VOICE display (page 55). This is useful when you want to check the proper bank select MSB/LSB values and program number to specify when selecting the voice from an external MIDI device. CVP-205/203 141 Making Global and Other Important Settings — Function Copying and Formatting Disks — Disk • Copying cannot be done between a 2DD disk and 2HD disk. When copying, make sure both disk are the same type. • Depending on the amount of data contained in the original source disk, you may have to swap the two disks several times until all of the data is properly copied. • Make sure to read the section “Using the Floppy Disk Drive (FDD) and Floppy Disks” on page 6. This function copies all the data from one disk to another, letting you back up all your important data before editing. For instructions, see “Copying from Disk to Disk” below. Turns the Song Auto Open function on or off. When this is set to “ON,” the Clavinova automatically calls up the first disk song when a disk is inserted. This function formats a floppy disk (see below). Copying from Disk to Disk As shown below, first copy the data of the original (source) disk to the CVP-205/203, then copy the data to the backup (destination) disk. 1 3 Press the [F] button. A message appears, prompting you to insert the source disk. At the “Please insert a destination disk and press the OK button ” prompt, eject the source disk and replace it with a blank, formatted disk, then press “OK.” To abort the operation, press “CANCEL.” 2 4 Internal memory Copy Insert the disk containing the original data into the drive and press “OK.” A “Now copying” message appears, and the CVP-205/203 begins copying data to internal memory. To abort the operation, press “CANCEL.” When the operation is finished (or when prompted), eject the destination disk. Source disk Copy Destination disk Commercially available music data is subject to protection by copyright laws. Copying commercially available data is strictly prohibited, except for your own personal use. Some music software is purposely copy-protected and cannot be copied. Formatting a Disk When using an unformatted disk for the first time, make sure to properly format it on the CVP-205/203. This includes blank disks as well as disks already initialized in a different format. Formatting erases all data on the disk. Insert the disk with shutter facing away from you and the label side up. To start the Format operation, press the [H] (DISK FORMAT) button, in the DISK page above. The Format operation initializes a disk with a specific file system, allowing the corresponding device (in this case, the CVP-205/203) to access it properly. Since there are several types of formats and disks available, you should know which ones to use with the CVP-205/203. 2DD disks are formatted to a capacity of 720 KB, and 2HD disks are formatted to a capacity of 1.44 MB. CAUTION Disk Lamp When the power is turned on, the disk lamp (at the bottom left of the drive) lights to indicate the drive can be used. 142 CVP-205/203 Formatting a disk completely erases all data on the disk. Make sure that the disk you’re formatting does not contain important data! Making Global and Other Important Settings — Function Entering Your Name and Language Preference — Owner Press this button to enter an Owner name (page 17; for instructions on naming see page 46). This name is automatically shown when you turn the power on. Determines the language used for the display messages. Once you change this setting, all messages will be shown in the selected language. When “JAPANESE” is selected for the Language parameter, and you change this to one of the western languages, the kanji and kana characters of the file name stored in the disk drive are changed to western characters. In the opposite case, special Latin characters and marks are changed into normal characters. Also, in the case of floppy disk data, text in the files are changed to characters that cannot be read by the instrument. Keep in mind that similar problems may occur when trying to access files originating or edited by a computer having a different language operating system. In general, be careful when switching languages — you risk not being able to access the data properly. Restoring the Factory-programmed Settings of the CVP-205/203 — System Reset This operation lets you restore the CVP-205/203 to its original factory settings. These settings include System Setup, MIDI Setup, User Effect, Music Finder, and Files & Folders. Restores the System Setup parameters to the original factory settings. You can also restore only the System Setup settings by simultaneously holding down the highest key on the keyboard (C7) and turning on the power. The functions and settings below do not apply to the Factory Reset operation. However, you can restore these to their original settings by calling up the preset System Setup files, using the Open/Save System Files function. Language Owner Name LCD Brightness Video Out settings (NTSC/ PAL, Size, Character Color, Background Color) (CVP205 only) Restores the MIDI templates to the original factory settings. Restores the User Effects (page 123) to the original factory settings. Restores the Music Finder data to the original factory settings. Deletes all files and folders stored in the User page. Executes the Factory Reset operation for all items checkmarked above. These call up the corresponding Open/ Save displays. These let you store the corresponding data as files to disk, for future recall. Pressing each of these buttons calls up the corresponding Open/Save display, from which you can select the corresponding PRESET page. From this PRESET page, you can save the relevant data. All Music Finder records can be stored together as a single file. When calling up a stored file, a message appears prompting you to replace or append the records as desired. Replace: All Music Finder records currently in the instrument are deleted and replaced with the records of the selected file. Append: The records called up are added to the vacant record numbers. CVP-205/203 143 Using Your Clavinova with Other Devices CAUTION Before connecting the Clavinova to other electronic components, turn off the power to all the components. Before turning the power on or off to all components, set all volume levels to minimum (0). Otherwise, electrical shock or damage to the components may occur. CVP-205 By connecting a microphone to the CVP-205, you can enjoy singing along with your own performance or song playback. (A dynamic microphone is recommended.) The Clavinova outputs your vocals or guitar sounds through the built-in speakers. CVP-203 INPUT VOLUME MIC. LINE IN MIC. LINE PHONES MAX PHONES MIN 2 Connecting the Microphone or Guitar (MIC./LINE IN jack) (CVP-205 only). 1 Connect your microphone to the MIC./LINE IN jack (standard 1/4" phone jack). Use an unidirectional microphone for best results. 2 1 1 2 Set the [MIC. LINE] switch (located next to the [MIC./LINE IN] jack) to the MIC. position. MIC. LINE 1 Using the Headphones (PHONES jacks). To use headphones, connect them to one of the PHONES jacks (standard 1/4" phone jacks) located on the underside of the keyboard. You can also determine whether or not the internal stereo speaker system is shut off when a pair of headphones is plugged into the PHONES jack (page 141). Two people can enjoy listening to the Clavinova together by connecting two pairs of headphones to the two jacks. MIC. LINE When connecting a microphone When connecting a guitar You should set the [MIC. LINE] switch to the LINE position when connecting an audio source with line-level output to the MIC./LINE IN jack. 3 Use the [INPUT VOLUME] knob (located next to the MIC./LINE IN jack) to set the microphone volume. CVP-205 IN OUT THRU L L+R PC-2 MIDI MIDI HOST SELECT 7 P.146 R TO HOST AUX PEDAL 8 6 P.146 P.146 VIDEO OUT AUX IN 5 4 P.145 P.145 CVP-203 R L (LEVEL FIXED) R L L+R R AUX OUT L L+R AUX IN 3 4 P.145 P.145 MIDI Mac PC-1 AUX PEDAL TO HOST MIDI PC-2 HOST SELECT THRU 6 P.146 144 CVP-205/203 L L+R R (LEVEL FIXED) L R PC-1 Mac 8 P.146 OUT 7 IN P.146 AUX OUT 3 P.145 Using Your Clavinova with Other Devices 345 Connecting Audio & Video Devices You can connect the Clavinova to a wide range of audio equipment by using the AUX IN and AUX OUT jacks, which are located at the bottom left of the instrument. Connect as shown in the illustrations below using standard audio cables. 4 Outputting the sound of an external device through the built-in speakers of the Clavinova (AUX IN jacks) CAUTION When the Clavinova’s AUX IN jacks are connected to an external device, first turn on the power of the external device, then that of the Clavinova. Clavinova Use audio cables and adaptor plugs with no resistance. L L+R R Tone generator AUX IN CAUTION LINE OUT When the Clavinova AUX OUT jacks are connected to an external audio system, first turn on the power to the Clavinova, then to the external audio system. Reverse this order when you turn the power off. 3 Playing the sounds of the Clavinova through an external audio system, and recording the sounds to an external recorder (AUX OUT jacks) CAUTION Never connect the Clavinova AUX OUT jacks to its AUX IN jacks, either directly or via external audio equipment. Such connections could result in a feedback loop that will make normal performance impossible, and may even damage the Clavinova. Clavinova L L+R Cassette tape recorder stereo system (LEVEL FIXED) L R R Phone plug (standard) Audio cable • The Clavinova’s [MASTER VOLUME] setting affects the input signal from the AUX IN jacks. • If you connect the Clavinova to a monaural device, use only the AUX IN L/L+R jack. 5 Showing the display of the Clavinova on a connected TV monitor (VIDEO OUT) (CVP-205 only) You can connect the Clavinova to a television or video monitor to display the lyrics in your song data or LCD on a larger screen. The size and color of the displayed characters can also be set, as well as the color of the display background (page 136). AUX OUT RCA pin plug Phone plug (standard) To powered speaker When these are connected (with standard phone plugs), you can use the [MASTER VOLUME] control to adjust the volume of the sound output to the external device. Audio cable AUX IN RCA pin plug When these are connected (with RCA pin plug; LEVEL FIXED), the sound is output to the external device at a fixed level, regardless of the [MASTER VOLUME] control setting. • For information on setting the video standard (NTSC or PAL), refer to page 136. The default setting is “PAL.” • Use an audio-video cable with good high-frequency characteristics and RCA-type pin jacks to connect the Clavinova to a television or video monitor. RCA pin plug RCA pin plug VIDEO IN L L+R AUX PEDAL • If you connect the Clavinova to a monaural device, use only the AUX OUT L/L+R jack. VIDEO OUT R AUX IN Television CVP-205 CVP-205/203 145 Using Your Clavinova with Other Devices 6 Using the Pedal (footswitch) or Foot Controller (AUX PEDAL jack) 8 Connecting to a Computer (MIDI terminals/TO HOST terminal) By connecting an optional Foot Controller (such as the FC7) to the AUX PEDAL jack, you can control any one of a variety of important functions with your foot — such as dynamically adjusting the volume as you play (page 131). Connect your CVP-205/203 to computer and take advantage of the wide range of powerful and versatile software for creating and editing music. The CVP-205/203 can be connected in three ways. By connecting a Foot Switch (the FC4 or FC5) to this jack, you can replicate the function of some panel buttons, doing things like starting and stopping accompaniment. ■ Using the TO HOST terminal ■ Using the MIDI terminals ■ Connecting to a USB terminal by using an optional USB interface (UX series) CAUTION Make sure to connect or disconnect the pedal only when the power is turned off. 7 Connecting external MIDI devices (MIDI terminals) • When connecting the Clavinova to a personal computer, first turn off the power to both the Clavinova and the computer before connecting any cables and setting the HOST SELECT switch. After making the proper connections and settings, turn on the power of the computer first, then that of the Clavinova. Using a standard MIDI cable, connect the external MIDI device to the MIDI terminal(s) of the Clavinova. Make sure to set the HOST SELECT switch (page 18) to MIDI when you use these connectors. For more information about connections, see “What You Can Do With MIDI” on page 150. • If you do not use the TO HOST terminal of the Clavinova, make sure you disconnect the cable from the terminal. If the cable is left connected, the Clavinova may not function properly. MIDI IN........... Receives MIDI messages from an external MIDI device MIDI OUT ....... Sends out MIDI messages generated by the Clavinova MIDI THRU ..... Simply relays the MIDI messages received at MIDI IN For a general overview of MIDI and how you can effectively use it, refer to the following sections: • What’s MIDI? (page 148) • What You Can Do With MIDI (page 150) • MIDI functions (page 137) • Never use MIDI cables longer than 15 meters. 146 • You’ll need an appropriate music/MIDI software program (such as a sequencer), compatible with your computer platform. CVP-205/203 • When the HOST SELECT switch is set to “PC-1,” “PC-2,” or “Mac,” you can use the TO HOST terminal, but the MIDI connectors are disabled since no data transfer occurs via the MIDI connectors. On the other hand, when the HOST SELECT switch is set to “MIDI,” you can use the MIDI connectors, but not the TO HOST terminal since no data is transferred via the TO HOST terminal. Note for Windows users (regarding MIDI driver) To transfer data via the computer’s serial port and the Clavinova’s TO HOST terminal, you need to install a specified MIDI driver (Yamaha CBX driver for Windows). You can download this driver from the XG Library on the Yamaha Web site: http://www.yamaha-xg.com Using Your Clavinova with Other Devices Using the TO HOST terminal Using the MIDI terminals Connect the serial port of the personal computer (RS232C terminal or RS-422 terminal) to the TO HOST terminal of the CVP-205/203. For the connection cable, use the appropriate cable below (sold separately) that matches the personal computer type. When using a MIDI interface device installed in the personal computer, connect the MIDI terminals of the personal computer and the CVP-205/203 with standard MIDI cables. If your system does not work properly with the connections and settings listed above, your software may require different settings. Check your software operation manual and set the HOST SELECT switch to the proper data transfer rate. (Data transfer rate of “PC-1” is 31,250 bps.) • When the computer has a MIDI interface installed, connect the MIDI OUT terminal of the personal computer to the MIDI IN terminal. Set the HOST SELECT switch to “MIDI.” Clavinova MIDI IN MIDI OUT MIDI OUT MIDI IN NEC MultiSync ■ IBM-PC/AT (Windows) PC-9821 AS NEC Connect the RS-232C terminal on the computer to the TO HOST terminal on the CVP-205/203 using a serial cable (D-SUB 9P → MINI DIN 8P cross cable). Set the CVP-205/203 HOST SELECT switch to the “PC-2.” (Data transfer rate is 38,400 bps.) Clavinova NEC MultiSync PC-9821 AS MINI DIN 8-pin D-sub 9-pin NEC CVP-205 PC-2 MIDI CVP-203 Mac PC-1 MINI DIN 8-pin PC-1 Mac MIDI PC-2 D-sub 25-pin D-sub 9-pin CVP-205 PC-2 MIDI CVP-203 PC-1 Mac Mac PC-1 • When using a MIDI interface with a Macintosh series computer, connect the RS-422 terminal of the computer (modem or printer terminal) to the MIDI interface, then connect the MIDI OUT terminal on the MIDI interface to the MIDI IN terminal of the CVP205/203, as shown in the diagram below. Set the HOST SELECT switch to “MIDI.” * When using a D-SUB 25P → MINI DIN 8P cross cable, connect using a DSUB9P plug adaptor on the computer side of the cable. Clavinova Set the MIDI interface clock in the sequencer you are using to 1 MHz. For details, refer to the owner’s manual for the particular software you are using. RS422 MINI DIN 8-pin PC-2 MIDI Connect RS-422 terminal (modem or printer) on the computer to the TO HOST terminal on the CVP-205/ 203 using a serial cable (system peripheral cable, 8 bit). Set the CVP-205/203 HOST SELECT switch to the “MAC” (Data transfer rate is 31,250 bps). MIDI IN MIDI OUT CVP-205 ■ Macintosh MIDI PC-2 CVP-203 PC-1 Mac Mac PC-1 MIDI PC-2 • When the HOST SELECT switch is set to “MIDI,” the TO HOST terminal is disabled. • When using a Macintosh series computer, set the MIDI interface clock setting in the application software to match the setting of the MIDI interface you are using. For details, refer to the owner’s manual for the particular software you are using. Clavinova MINI DIN 8-pin CVP-205 PC-2 MIDI MINI DIN 8-pin CVP-203 PC-1 Mac Mac PC-1 MIDI PC-2 CVP-205/203 147 Using Your Clavinova with Other Devices Using the USB terminal on your computer with a USB/MIDI interface (UX256/UX96, etc.) Connect the UX256/UX96 and the computer with a USB cable. Install the included UX256/UX96 driver to the computer, and connect the UX256/UX96 to the CVP-205/ 203 with a MIDI cable. Set the HOST SELECT switch on the CVP-205/203 to “MIDI.” For details, refer to the owner’s manual of the UX256/UX96. IN Now let’s examine what happens when we play back a recording. When you playback a music CD (for example, a solo piano recording), you’re hearing the actual sound (vibrations in air) of the acoustic instrument. This is called audio data, to distinguish it from MIDI data. Recording and playing back the performance of an acoustic instrument (audio data) Recording Playback OUT MIDI USB cable NEC MultiSync UX256 Clavinova MIDI IN PC-9821 AS MIDI OUT NEC Personal computer CVP-205 PC-2 MIDI CVP-203 PC-1 Mac Mac PC-1 MIDI PC-2 For details about the necessary MIDI settings for computer and sequence software you are using, refer to the relevant owner’s manuals. What’s MIDI? In the above example, the actual acoustic sounds of the pianist’s performance are captured in the recording as audio data, and this is recorded to CD. When you play back that CD on your audio system, you can hear the actual piano performance. The piano itself is not necessary, since the recording contains the actual sounds of the piano, and your speakers reproduce them. Recording and playing back the performance of a digital instrument (MIDI data) Let’s consider an acoustic piano and a classical guitar as representative acoustic instruments. With the piano, you strike a key, and a hammer inside hits some strings and plays a note. With the guitar, you directly pluck a string and the note sounds. But how does a digital instrument go about playing a note? Acoustic guitar note production Recording Playback Tone generator Sequencer Controller (keyboard, etc.) FD Digital instrument note production FD Internal amp L Tone generator (Electric circuit) Internal amp R Playing the keyboard Pluck a string and the body resonates the sound. Based on playing information from the keyboard, a sampled note stored in the tone generator is played through the speakers. As shown in the illustration above, in an electronic instrument, the sampled note (previously recorded note) stored in the tone generator section (electronic circuit) is played based on information received from the keyboard, and output through the speakers. 148 CVP-205/203 In the case of digital instruments, the audio signals are sent through output jacks (such as AUX OUT) on the instrument. Using Your Clavinova with Other Devices The “controller” and “tone generator” in the illustration above are equivalent to the piano in our acoustic example. Here, the player’s performance on the keyboard is captured as MIDI song data (see illustration below). In order to record the audio performance on an acoustic piano, special recording equipment is needed. However, since the Clavinova features a built-in sequencer that lets you record performance data, this recording equipment is unnecessary. Instead, your digital instrument — the Clavinova — allows you to both record and play back the data. ■ Example Keyboard Data Voice number (with what voice) 01 (grand piano) Note number (with which key) 60 (C3) Note on (when was it pressed) and note off (when was it released) Timing expressed numerically (quarter note) Velocity (about how strong) 120 (strong) Panel operations on the CVP-205/203, such as playing the keyboard and selecting voices, are processed and stored as MIDI data. The auto accompaniment styles and songs also consist of MIDI data. Tone generator Sequencer Keyboard performance (MIDI data) However, we also need a sound source to produce the audio, which eventually comes from your speakers. The tone generator of the Clavinova fills this function. The recorded performance is reproduced by the sequencer, playing back the song data, using a tone generator capable of accurately producing various instrument sounds — including that of a piano. Looked at in another way, the relation of the sequencer and the tone generator is similar to that of the pianist and the piano — one plays the other. Since digital instruments handle playback data and the actual sounds independently, we can hear our piano performance played by another instrument, such as guitar or violin. Even though it is a single musical instrument, the Clavinova can be thought of as containing several electronic components: a controller, a tone generator, and a sequencer. Finally, we’ll take a look at the actual data that gets recorded and that serves as the basis for playing the sounds. For example, let’s say you play a “C” quarter note using the grand piano sound on the CVP-205/203 keyboard. Unlike an acoustic instrument that puts out a resonated note, the electronic instrument puts out information from the keyboard such as “with what voice,” “with which key,” “about how strong,” “when was it pressed” and “when was it released.” Then each piece of information is changed into a number value and sent to the tone generator. Using these numbers as a basis, the tone generator plays the stored sampled note. MIDI is an acronym that stands for Musical Instrument Digital Interface, which allows electronic musical instruments to communicate with each other, by sending and receiving compatible Note, Control Change, Program Change and various other types of MIDI data, or messages. The CVP-205/203 can control a MIDI device by transmitting note related data and various types of controller data.The CVP-205/203 can be controlled by incoming MIDI messages which automatically determine the tone generator mode, select MIDI channels, voices and effects, change parameter values and of course play the voices specified for the various parts. MIDI data has the following advantages over audio data: • The amount of data is much less, letting you easily store MIDI songs to floppy disk. • The data can be effectively and easily edited, even to the point of changing voices and transforming the data. MIDI messages can be divided into two groups: Channel messages and System messages. ■ Channel Messages The CVP-205/203 is an electronic instrument that can handle 16 channels (or 32 channels, when using the TO HOST terminal). This is usually expressed as “it can play 16 instruments at the same time.” Channel messages transmit information such as Note ON/OFF, Program Change, for each of the 16 channels. Message Name CVP-205/203 Operation/Panel Setting Note ON/OFF Messages which are generated when the keyboard is played. Each message includes a specific note number which corresponds to the key which is pressed, plus a velocity value based on how hard the key is played. Program Change Voice selecting (control change bank select MSB/LSB setting) Control Change Volume, panpot (Mixing Console), etc. The performance data of all songs and styles is handled as MIDI data. CVP-205/203 149 Using Your Clavinova with Other Devices MIDI channels MIDI performance data is assigned to one of sixteen MIDI channels. Using these channels, 1 - 16, the performance data for sixteen different instrument parts can be simultaneously sent over one MIDI cable. Think of the MIDI channels as TV channels. Each TV station transmits its broadcasts over a specific channel.Your home TV set receives many different programs simultaneously from several TV stations and you select the appropriate channel to watch the desired program. As you can see, it is essential to determine which data is to be sent over which MIDI channel when transmitting MIDI data (page 138). The Clavinova also allows you to determine how the received data is played back. (page 139). ■ System Messages This is data that is used in common by the entire MIDI system. System messages include messages like Exclusive Messages that transmit data unique to each instrument manufacturer and Realtime Messages that control the MIDI device. Message Name CVP-205/203 Operation/Panel Setting System Exclusive Message Effect type settings (Mixing Console), etc. Realtime Messages Clock setting, Start/stop operation Weather Report News 1 2 News 2 MIDI operates on the same basic principle. The transmitting instrument sends MIDI data on a specific MIDI channel (MIDI Transmit Channel) via a single MIDI cable to the receiving instrument. If the receiving instrument’s MIDI channel (MIDI Receive Channel) matches the Transmit Channel, the receiving instrument will sound according to the data sent by the transmitting instrument. MIDI cable MIDI transmit channel 2 MIDI receive channel 2 The Clavinova’s keyboard and internal tone generator are also connected by MIDI (page 137). For example, several tracks (channels) can be transmitted simultaneously, including the style data (as shown below). The messages transmitted/received by the CVP-205/203 are shown in the MIDI Data Format and MIDI Implementation Chart in the separate Data List. What You Can Do With MIDI The following MIDI settings can be made on the Clavinova: • MIDI templates (preset MIDI setups for various applications) (page 137) • Transmit (page 138) • Receive (page 139) • Local Control (page 137) • Clock (page 138) ■ Record performance data (1-16 channels) using the CVP-205/203 Auto Accompaniment features on a external sequencer (such as a personal computer). After recording, edit the data with the sequencer, then play it again on the CVP-205/203 (playback). Example: Recording the auto accompaniment of the Clavinova to an external sequencer MIDI receive Clavinova MIDI IN MIDI OUT MIDI OUT MIDI IN NEC MultiSync PC-9821 AS NEC MIDI transmit MIDI cable or serial cable Clavinova track (channnel) MAIN LAYER LEFT STYLE instrument STYLE instrument STYLE instrument STYLE instrument STYLE instrument STYLE instrument STYLE instrument STYLE instrument Channel 1 Channel 2 Channel 3 Channel 4 Channel 5 Channel 6 Channel 7 Channel 8 Channel 9 Channel 10 Channel 11 External sequencer Track 1 Track 2 Track 3 Track 4 Track 5 Track 6 Track 7 Track 8 Track 9 Track 10 Track 11 When you want to use the Clavinova as an XGcompatible multi-timbral tone generator, set the receive part for MIDI channels 1 to 16 to “SONG” in MIDI Receive (page 139). ■ Play and control the Clavinova from a separate keyboard Clavinova MIDI receive MIDI IN 150 CVP-205/203 Personal cumputer, QY series etc. MIDI OUT Using Your Clavinova with Other Devices Data Compatibility This section covers basic information on data compatibility: whether or not other MIDI devices can playback the data recorded by CVP-205/203, and whether or not the CVP-205/203 can playback commercially available song data or song data created for other instruments or on a computer. Depending on the MIDI device or data characteristics, you may be able to play back the data without any problem, or you may have to perform some special operations before the data can be played back. If you run into problems playing back data, please refer to the information below. Disk format Sequence Format The system which records song data is called “sequence format.” Playback is only possible when the sequence format of the disk matches that of the MIDI device. The CVP-205/ 203 is compatible with the following formats. ■ SMF (Standard MIDI File) This is the most common sequence format. Standard MIDI Files are generally available as one of two types: Format 0 or Format 1. Many MIDI devices are compatible with Format 0, and most commercially available software is recorded as Format 0. • The CVP-205/203 is compatible with both Format 0 and Format 1. Floppy disks are the main storage medium for data used with various devices, including computers. Different devices have different systems of storing data, therefore it is necessary to first configure the floppy disk to the system of the device being used.This operation is called “formatting.” • Song data recorded on the CVP-205/203 is automatically recorded as SMF Format 0. • There are two types of floppy disks: MF2DD (double sided, double density) and MF2HD (double sided, high density), and each type has different formatting systems. ■ ESEQ • CVP-205/203 can record and playback with both types of floppy disks. • When formatted by the CVP-205/203, a 2DD disk stores up to 720 KB (kilobytes) and a 2HD disk stores up to1.44 MB (megabytes). (The figures “720 KB” and “1.44MB” indicate the data memory capacity. They are also used to indicate the format type of disk.) • Playback is only possible when the MIDI device to be used is compatible with the format of the disk. • Song data loaded to the CVP-205/203 is automatically saved as SMF Format 0 regardless of the original format. This sequence format is compatible with many of Yamaha’s MIDI devices, including the Clavinova series instruments.This is a common format used with various Yamaha software. ■ XF The Yamaha XF format enhances the SMF (Standard MIDI File) format with greater functionality and open-ended expandability for the future. • The CVP-205/203 is capable of displaying lyrics when an XF file containing lyric data is played. ■ Style File The Style File Format – SFF – is Yamaha’s original style file format which uses a unique conversion system to provide high-quality automatic accompaniment based on a wide range of chord types. CVP-205/203 151 Using Your Clavinova with Other Devices Voice Allocation Format With MIDI, voices are assigned to specific numbers, called “program numbers.” The numbering standard (order of voice allocation) is referred to as the “voice allocation format.” Voices may not play back as expected unless the voice allocation format of the song data matches that of the compatible MIDI device used for playback. The CVP-205/203 is compatible with the following formats. Even if the devices and data used satisfy all the conditions above, the data may still not be completely compatible, depending on the specifications of the devices and particular data recording methods. ■ GM System Level 1 This is one of the most common voice allocation formats. • Many MIDI devices are compatible with GM System Level1, as is most commercially available software. ■ XG XG is a major enhancement of the GM System Level 1 format, and was developed by Yamaha specifically to provide more voices and variations, as well as greater expressive control over voices and effects, and to ensure compatibility of data well into the future. • Song data recorded on the CVP-205/203 using voices in the [XG] category is XG-compatible. ■ DOC This voice allocation format is compatible with many of Yamaha’s MIDI devices, including the Clavinova series instruments.This is also a common format used with various Yamaha software. 152 CVP-205/203 CVP-205/205M: Keyboard Stand Assembly CAUTION ■ Be careful not to confuse parts, and be sure to install ■ ■ ■ ■ all parts in the correct direction. Please assemble in accordance with the sequence given below. Assembly should be carried out by at least two persons. Be sure to use the correct screw size, as indicated below. Use of incorrect screws can cause damage. Be sure to tighten up all screws upon completing assembly of each unit. Have a Phillips-head (+) To disassemble, reverse screwdriver ready. the assembly sequence given below. 3 Attach the front panel. 1 Align and attach the front panel to the front side of the pedal box and both side panels. 2 Secure the panel using the 4x14mm thin screws. * Insert six screws into the smaller holes on the brackets. the package, take out the pedal box, take out 1 Open the styrofoam pads, and place the main unit on top of the pads. Position the pads so that they will protect the headphone jack and the connector panel located underneath the front left corner, and the floppy disk drive located underneath the front right corner. Main unit 4 Mount the main unit. CAUTION Floppy disk drive Phones jacks Connector panel Styrofoam pads • Fingers can become pinched between the main unit and the rear or side panels, be extra careful so as not to drop the main unit. • Do not hold the keyboard in any position other than the position shown in the illustration. Remove the parts shown below from the box. Be sure to place your hands at least 10 cm from either end of the main unit when positioning it. Front panel Rear panel Pedal box Pedal cord At least 10 cm Side panel (left) Side panel (right) AC power cord Assembly Parts 5 6 x 25 mm long screws x4 6 x 16 mm short screws x4 4 x 20 mm tapping screws x5 4 x 14 mm thin screws x8 Cord holders x2 2 Fix the main unit. 1 Center the main unit to produce equal clearance on the left and right sides. Attach the side panels to the pedal box. Side panel (left) 2 Remove the vinyl tie from the folded pedal cord. Do not remove the vinyl tie located next to the hole. Side panel (right) 1 Use the four 6x25 mm long screws to attach the pedal box. First attach one side panel, then attach the other side panel. 2 Use 6x16 mm short screws to secure the main unit from the rear. * Use the front hole on the front brackets to attach the screws. CVP-205/203 153 CVP-205/205M: Keyboard Stand Assembly 6 Connect the speaker cord. 1 Before connecting the speaker cord, remove the vinyl tie attaching the speaker cord to the front panel. 2 Insert the speaker cord plug into the connector, with the plug’s tab facing the rear. 7 WARNING Connect the pedal cord. • An improper voltage setting can cause serious damage to the Clavinova or result in improper operation. 1 Insert the pedal cord plug into the pedal connector. 2 Attach the cord holders to the side panel as shown, then clip the cord into the holders. 8 Voltage Selector Before connecting the AC power cord, check the setting of the voltage selector which is provided in some areas. To set the selector for 110V, 127V, 220V or 240V main voltages, use a “minus” screwdriver to rotate the selector dial so that the correct voltage for your region appears next to the pointer on the panel. The voltage selector is set at 240V when the unit is initially shipped. After the proper voltage has been selected, connect the AC power cord to the AC INLET and an AC wall outlet. A plug adaptor may be also provided in some areas to match the pin configuration of the AC wall outlets in your area. Attach the rear panel. 2 Secure the left and right corners using the 4x14mm thin screws. ■ After completing the assembly, please check the following. • Are there any parts left over? → Review the assembly procedure and correct any errors. • Is the Clavinova clear of doors and other movable fixtures? → Move the Clavinova to an appropriate location. • Does the Clavinova make a rattling noise when you shake it? → Tighten all screws. • Are the pedal and power cords inserted securely into the sockets? → Check the connection. • If the main unit creaks or is otherwise unsteady when you play on the keyboard, refer to the assembly diagrams and retighten all screws. When moving the instrument after assembly, always hold instrument by the lower surface in the front of the main unit and by the handles in the rear panel. 1 With the rear panel on the feet’s protruding edge, align the panel with the groove and secure the top of the panel. 9 CAUTION Do not hold the key cover or top portion. Improper handling can result in damage to the instrument or personal injury. 3 Secure the top center and bottom of the panel using the 4x20mm tapping screws. Top portion Set the voltage selector and connect the power cord. Key cover 220 240 110 127 154 CVP-205/203 CVP-203: Keyboard Stand Assembly CAUTION Be careful not to confuse parts, and be sure to install all parts in the correct direction. Please assemble in accordance with the sequence given below. Assembly should be carried out by at least two persons. Be sure to use the correct screw size, as indicated below. Use of incorrect screws can cause damage. Be sure to tighten up all screws upon completing assembly of each unit. To disassemble, reverse the assembly sequence given below. ■ ■ ■ ■ ■ Have a Phillips-head (+) screwdriver ready. 2 Attach the side panels to the pedal box. 1 Untie and straighten out the bundled Side panel (left) cord attached to the bottom of the pedal box. Don’t discard the vinyl tie, you’ll need it later in step 6. Side panel (right) 2 Use the four 6x25 mm long screws to attach the pedal box. First attach one side panel, then attach the other side panel. 3 Attach the rear panel. 1 Place the bottom edges of the rear panel on the feet’s protruding 1 Open the package, take out the pedal box, take out the styrofoam pads, and place the main unit on top of the pads. Position the pads so that they will protect the headphone jack and the connector panel located underneath the front left corner, and the floppy disk drive located underneath the front right corner. edges, with the panel slightly angled as shown in the illustration. The wooden pattern side of the panel should be facing outside. Then, align the top part of the panel with the side panels. 2 Secure the top of the rear panel to the side panel brackets using two 4x12 mm thin screws. 3 Secure the bottom of the rear panel to the pedal box using four 4x20 mm tapping screws. Main unit Styrofoam pads Floppy disk drive Remove the parts shown below from the box. Rear panel Pedal box 4 Bundled pedal cord inside Mount the main unit. CAUTION Side panel (left) Assembly Parts Side panel (right) AC power cord • Fingers can become pinched between the main unit and the rear or side panels, be extra careful so as not to drop the main unit. • Do not hold the keyboard in any position other than the position shown in the illustration. Be sure to place your hands at least 10 cm from either end of the main unit when positioning it. 6 x 25 mm long screws x4 6 x 16 mm short screws x4 4 x 20 mm tapping screws x4 4 x 12 mm thin screws x2 Cord holders x2 At least 10 cm CVP-205/203 155 CVP-203: Keyboard Stand Assembly 5 Fix the main unit. WARNING • An improper voltage setting can cause serious damage to the Clavinova or result in improper operation. 1 Center the main unit to produce equal clearance on the left and right sides. 8 2 Use 6x16 mm short screws to secure the main unit from the front. Set the adjuster. Rotate the adjuster until it comes in firm contact with the floor surface. 6 Connect the pedal cord. 1 Insert the pedal cord plug to the pedal connector from the front. 3 Use a vinyl tie to take up any slack in the pedal cord. 2 Attach the cord holders to the rear panel as shown, then clip the cord into the holders. 7 Set the voltage selector and connect the power cord. ■ After completing the assembly, please check the following. • Are there any parts left over? → Review the assembly procedure and correct any errors. • Is the Clavinova clear of doors and other movable fixtures? → Move the Clavinova to an appropriate location. • Does the Clavinova make a rattling noise when you shake it? → Tighten all screws. • Does the pedal box rattle or give way when you step on the pedals? → Turn the adjuster so that it is set firmly against the floor. • Are the pedal and power cords inserted securely into the sockets? → Check the connection. • If the main unit creaks or is otherwise unsteady when you play on the keyboard, refer to the assembly diagrams and retighten all screws. When moving the instrument after assembly, always hold the bottom of the main unit. 110 127 220 240 Voltage Selector Before connecting the AC power cord, check the setting of the voltage selector which is provided in some areas. To set the selector for 110V, 127V, 220V or 240V main voltages, use a “minus” screwdriver to rotate the selector dial so that the correct voltage for your region appears next to the pointer on the panel. The voltage selector is set at 240V when the unit is initially shipped. After the proper voltage has been selected, connect the AC power cord to the AC INLET and an AC wall outlet. A plug adaptor may be also provided in some areas to match the pin configuration of the AC wall outlets in your area. 156 CVP-205/203 CAUTION Do not hold the key cover or top portion. Improper handling can result in damage to the instrument or personal injury. Top portion Key cover Troubleshooting Problem Possible Cause and Solution • The Clavinova does not turn on; there is no power. Make sure that the Clavinova has been plugged in properly. Securely insert the female plug into the AC socket on the Clavinova, and the male plug into a proper AC outlet (page 17). • A click or pop is heard when the power is turned on or off. This is normal when electrical current is applied to the instrument. • Noise is heard from the Clavinova’s speakers. Using a mobile phone in close proximity to the Clavinova may produce interference. To prevent this, turn off the mobile phone, or use it further away from the Clavinova. • The display is too bright or too dark to read. The brightness of the display may be affected by the surrounding temperature; try adjusting the contrast (page 17). • The keyboard volume is low compared to that of the Auto Accompaniment or song playback. The overall keyboard volume or the independent volume level of the keyboard part may be set too low. Raise the MAIN/LAYER/LEFT volume voices or lower the STYLE/SONG volume in the BALANCE display (page 62). • The volume of the Auto Accompaniment or song playback is low compared to that of the keyboard. The volume level of one or more accompaniment parts or song channels is set too low. Raise the part or channel level(s) in the appropriate MIXER display (page 120). • The overall volume is low, or no sound is heard. • The Master Volume is set too low; set it to an appropriate level with the [MASTER VOLUME] dial. • The volume of the individual parts may be set too low. Raise the volume of MAIN, LAYER, LEFT, STYLE, and SONG in the BALANCE display (page 62). • Make sure the desired channel is set to ON (page 62, 77). • Headphones are connected, disabling the speaker output. (This happens when the speaker setting is set to “HEADPHONE SW”; page 141.) Unplug the headphones. • Make sure the speaker setting is set to ON (page 141). • Make sure the Local Control function is set to ON (page 137). • The damper, sostenuto and soft functions do not work for the relevant pedals. Each pedal has been assigned to a different function. Make sure that each pedal is properly assigned to SUSTAIN, SOSTENUTO, and SOFT (page 131). • The damper pedal has no effect, or the sound continuously sustains even when the damper pedal is not pressed. The pedal cable/plug may not be properly connected. Make sure to securely insert the pedal plug into the proper jack (page 153 - 156). • Not all simultaneously-played notes sound. You may be exceeding the maximum polyphony of the Clavinova. When this happens, the earliest played notes will stop sounding, letting the latest played notes sound. See page 159 for information on the maximum polyphony. • Accompaniment style or Song playback does not start. • MIDI Clock may be set to “EXTERNAL.” Make sure this is set to “INTERNAL” (page 138). • Make sure to press the appropriate [START/STOP] button. To play an accompaniment style, press the STYLE [START/STOP] button (page 62); to playback a song, press the SONG [START/STOP] button (page 75). • “New Song” (a blank song) has been selected. Make sure to select an appropriate song in the SONG display (page 75). • The song has been stopped at the end of the song data. Return to the beginning of the song by pressing the [TOP] button (page 77). • Only the rhythm channel plays. Make sure the Auto Accompaniment function is turned on; press the [ACMP] button. • The accompaniment style does not start, even when Synchro Start is in standby condition and a key is pressed. You may be trying to start accompaniment by playing a key in the right hand range of the keyboard. Make sure to play a key in the left-hand (accompaniment) range of the keyboard. • The desired chord is not recognized or output by the auto accompaniment. • You may not be playing the correct keys to indicate the chord. Refer to “Chord Types Recognized in the Fingered Mode” (page 64). • You may be playing the keys according to a different fingering mode, and not the one currently selected. Check the accompaniment mode, and play the keys according to the selected mode (page 63). CVP-205/203 157 Troubleshooting Problem 158 Possible Cause and Solution • Auto accompaniment chords are recognized regardless of the split point or where chords are played on the keyboard. This is normal if the fingering mode is set to “Full Keyboard” or “AI Full Keyboard.” If either of these is selected, chords are recognized over the entire range of the keyboard, irrespective of the split point setting. If desired, select a different fingering mode (page 63). • Certain notes sound at the wrong pitch. The Scale parameter has probably been set to something other than “Equal,” changing the tuning system of the keyboard. Make sure “Equal” is selected as the Scale in the Scale Tune page (page 127). • Some channels do not properly play back when playing back song data. Make sure that playback of the relevant channel(s) is turned on (page 77). • The Harmony function does not operate. Harmony cannot be used with the Full Keyboard or AI Full Keyboard fingering modes. Select an appropriate fingering mode (page 63). • The microphone input signal (CVP-205 only) cannot be recorded. This is normal; recording the audio input of the microphone is not possible. • MIDI data is not transmitted or received via the MIDI terminals, even when MIDI cables are connected properly. Make sure the HOST SELECT switch is set to “MIDI” (page 147). The MIDI terminals cannot be used for the other switch settings. • When a voice is changed, the previously selected effect is changed. Each voice has its own suitable preset values which are automatically recalled when the corresponding Voice Set parameters are turned on (page 135). • There is a slight difference in sound quality between notes played on the keyboard. • Some voices have a looping sound. • Some noise or vibrato is noticeable at higher pitches, depending upon the voice. This is normal and is a result of the Clavinova’s sampling system. • Some voices will jump an octave in pitch when played in the upper or lower registers. This is normal. Some voices have a pitch limit which, when reached, causes this type of pitch shift. • Disk save operations take a long time. This is normal. Keep in mind that it takes approximately 1 minute to save 1 megabyte of data to a floppy disk. • The voice produces excessive noise. Certain voices may produce noise, depending on the Harmonic Content and/or Brightness settings in the FILTER page of the Mixing Console display (page 121). • The sound is distorted or noisy. • The volume may be turned up too high. Make sure all relevant volume settings are appropriate. • This may be caused by the effects. Try canceling all unnecessary effects, especially distortion-type effects (page 122). • Some filter resonance settings in the Custom Voice Creator display (page 91) can result in distorted sound. Adjust these settings if necessary. • A strange “flanging” or “doubling” sound occurs. Also, the sound is slightly different each time the keys are played. Both the Main and Layer parts are set to “ON,” and both parts are set to play the same voice. Set the Layer part to “OFF” (page 57) or change the voice for each part (page 55). CVP-205/203 Specifications : available Model Name CVP-205 Sound Source 320 ✕ 240 dots backlit graphic LCD Display Keyboard Voice CVP-203 AWM Dynamic Stereo Sampling 88 keys (A-1 - C7) Polyphony (max) 96 Voice Selection 64 308 voices + 480 XG voices + 16 Drum Kits Regular Voice 287 Sweet Voice 8 Cool Voice 2 Live Voice 1 Natural Voice 21 Sound creator Effects Effect Blocks Reverb 2 Chorus 2 DSP Brilliance Effect Types — REVERB1 28+3 User REVERB2 5 CHORUS1 21+3 User CHORUS2 3 DSP1 101+3 User DSP2 12 Brilliance Accompaniment Style 2 1 Accompaniment Styles 5 — 194 175 Session Styles 12 Pianist Styles 36 Piano Combo Styles Fingering 17 Single Finger, Fingered, Fingered On Bass, Multi Finger, AI Fingered, Full Keyboard, AI Full Keyboard Style Creator OTS (One Touch Setting) Accompaniment Style OTS link Music Finder Approximately 2500 records Edit Song Format SMF (Format 0,1), ESEQ Preset Songs Guide Follow Lights, Any Key, Karao-Key Guide Lamp 88 Red Lyrics Score — Recording Quick Recording, Multi Track Recording, Step Recording, Song Editing Record Channels Memory Device Floppy Disk (2HD,2DD) Tempo Tempo Range Flash Memory (internal) Flash Availability 16 1MB Song (SMF), Style (SFF), Registration, Voice, etc. 5 - 500 Tap Tempo Metronome Sound Bell on/off, Human Voices (5 languages) CVP-205/203 159 Specifications Model Name Registration Memory CVP-205 CVP-203 Buttons 8 Regist Sequence Freeze Others Demo Language Function, Voice, Style 6 languages (English, Japanese, German, French, Spanish, Italian) Help Direct Access Piano setting button (including Piano Lock) Master Volume Fade In/Out Transpose Keyboard/Song/Master Tuning Tuning Curve Scale Flat/Stretch (Natural Piano Voice only) Equal Temperament, Pure Major/Pure Minor, Pythagorean, Mean Tone, Werckmeister/Kirnberger, Arabic 1/2 Touch Response 5 level PHONES ✕ 2, MIDI (THRU, OUT, IN), TO HOST, HOST SELECT, AUX PEDAL, AUX IN (L/L+R), AUX OUT (LEVEL FIXED) (L/R), AUX OUT (L/L+R) Jacks/Connectors MIC (INPUT VOLUME, MIC./ LINE IN),VIDEO OUT Pedals Number of Pedals Pedal Functions Amplifiers/ Speakers 3 VOLUME, SUSTAIN, SOSTENUTO, SOFT, GLIDE, PORTAMENTO, PITCHBEND, MODULATION, DSP VARIATION, VIBROTOR ON/OFF, SONG START/STOP, STYLE START/STOP, etc. 40 W ✕ 2 Amplifiers Speakers Dimensions [W ✕ D ✕ H] (with the Music Stand) Weight — (16 cm + 5 cm) ✕ 2 1384.0 ✕ 598.2 ✕ 900.1 mm [54-1/2" ✕ 23-9/16" ✕ 35-7/16"] (1384.0 ✕ 598.2 ✕ 1070.0 mm) [54-1/2" ✕ 23-9/16" ✕ 42-1/8"] 80 Kg (176 lbs., 6 oz) 1381.5 ✕ 597.7 ✕ 899.6mm [56-3/8" ✕ 24-3/8" ✕ 43-3/4"] (1381.5 ✕ 597.7 ✕ 1071.2mm) [56-3/8" ✕ 24-3/8" ✕ 36-11/16"] 66 Kg (145 lbs., 8 oz) * Specifications and descriptions in this owner's manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer. 160 CVP-205/203 Index Numerics 1 - 16 ................................................................................. 106 [1▲▼] - [8▲▼] buttons ........................................... 18, 39–46 A [A] - [J] buttons............................................................... 18, 41 Accessories ............................................................................ 6 Accompaniment Guide ........................................................ 79 Accompaniment style parts................................................... 95 [ACMP] button ............................................................... 18, 61 Adjust the Volume Balance and Changing Voices .............. 119 Adjusting the display contrast ............................................... 17 Adjusting the Effects ........................................................... 122 Adjusting the Tempo ............................................................ 51 Adjusting the Volume Balance ............................................. 62 Adjusting the Volume Balance / Muting Specific Channels ... 77 Adjusting values ................................................................... 47 AI ......................................................................................... 63 AI FINGERED ....................................................................... 63 AI FULL KEYBOARD ............................................................ 63 Any Key ............................................................................... 79 Append ................................................................................ 72 Applying Voice Effects.......................................................... 58 Appropriate Panel Setting for the Selected Style.................... 68 Arabic ................................................................................ 128 Arranging the Style Pattern ................................................... 65 Assembling an Accompaniment Style ................................. 113 ATTACK ............................................................................... 91 AUTO .................................................................................. 20 Auto Revoice...................................................................... 120 [AUTO FILLIN] button.................................................... 18, 67 Automatically Changing One Touch Settings with the Sections............................................................... 69 AUX IN [L / L+R] [R] jacks............................................ 19, 145 AUX OUT (LEVEL FIXED) [L] [R] jacks.......................... 19, 145 AUX OUT [L / L+R] [R] jacks........................................ 19, 145 [AUX PEDAL] jack........................................................ 19, 146 B [BACK] button .......................................................... 18, 41, 47 [BALANCE] button ......................................................... 18, 62 Bar Clear ............................................................................ 116 Bar Copy ............................................................................ 116 Basic Operations — Organizing Your Data .......................... 39 Bass...................................................................................... 95 BEAT .............................................................................. 71, 72 [BREAK] button .............................................................. 18, 65 BRIGHTNESS ....................................................................... 91 C Calling Up Ideal Setups for Your Music ................................ 70 Cent ................................................................................... 127 Change the Rhythmic Feel.................................................. 114 Changing Pitch-related Settings .......................................... 121 Changing the Automatically Selected Voice Settings .......... 135 Changing the Icon ................................................................ 47 Changing the Tone of the Voice ......................................... 121 Changing the Touch Sensitivity and Transpose ................... 133 Channel ................................................. 62, 77, 103, 116, 129 Channel Messages .............................................................. 149 Channel Muting ................................................................... 62 [CHANNEL ON / OFF] button ..................................18, 62, 77 Channel Transpose .............................................................105 CHD ...................................................................................107 Chord ...................................................................................95 Chord Detect ......................................................................139 Chord Events.......................................................................107 Chord Fingering ............................................................63, 131 Chord Tutor ........................................................................131 Chord Types Recognized in the Fingered Mode ....................64 Chorus ................................................................................124 Clock ..................................................................................138 COMMON ...........................................................................90 Compatible Song Types ........................................................74 CONFIG 1 ..........................................................................140 CONFIG 2 ..........................................................................141 Connect the power cord .......................................................17 Connecting Audio & Video Devices....................................145 Connecting external MIDI devices ......................................146 Connecting the Microphone or Guitar (CVP-205 only)........144 Connecting to a Computer ..................................................146 Controller ...........................................................................131 Converting into Kanji (Japanese language) ............................46 Cool! ....................................................................................56 COPY ...................................................................................44 Copying and Formatting Disks ............................................142 Copying Files/Folders............................................................44 Copying from Disk to Disk..................................................142 Creating Accompaniment Styles..........................................109 Current Memory ...................................................................40 Customizing the Event List — Filter.....................................108 CUT......................................................................................43 CVP-203: Keyboard Stand Assembly...................................155 CVP-205/205M: Keyboard Stand Assembly.........................153 D Damper pedal.................................................................19, 59 Data Compatibility..............................................................151 [DATA ENTRY] dial ........................................................18, 47 Data Types in the MIDI TRANSMIT/RECEIVE Display .........138 DECAY .................................................................................91 DELETE .................................................................................44 Delete.................................................................................104 DELETE RECORD..................................................................72 Deleting Files/Folders............................................................44 [DEMO] button.........................................................14, 18, 53 DEPTH..................................................................................91 Detailed Settings for Notation ...............................................82 [DIGITAL RECORDING] button........................14, 18, 93, 109 [DIRECT ACCESS] button................................................18, 48 Direct Access Chart ..............................................................49 Disk ....................................................................................142 Disk format .........................................................................151 Disk Orchestra Collection.....................................................19 Displaying Music Notation ...................................................81 Displaying the Lyrics.............................................................84 Displaying Upper Level pages...............................................45 DOC...................................................................................152 Drum ....................................................................................56 [DSP] button ...........................................................18, 58, 124 Dynamics ...........................................................................115 CVP-205/203 161 Index E ECHO .......................................................................... 59, 135 EDIT ................................................................................... 112 Edit the Created Accompaniment Style ............................... 114 Editing a Recorded Song..................................................... 103 Editing Channel-related Parameters .................................... 103 Editing Chord Events .......................................................... 107 Editing Note Events ............................................................ 106 Editing Records .................................................................... 72 Editing System Events ......................................................... 107 Editing the Channel Data.................................................... 116 Editing Voices ...................................................................... 88 EFFECT ................................................................................. 92 Effect Block ........................................................................ 123 Effect Structure ................................................................... 124 Effects................................................................................. 122 EG ........................................................................................ 91 Embellish and enhance your melodies — with the automatic Harmony and Echo effects.............. 30 END Mark .......................................................................... 101 ENDING .............................................................................. 67 [ENDING / rit.] button .............................................. 18, 31, 66 [ENTER] button .............................................................. 18, 47 Entering Characters............................................................... 46 Entering Chords and Sections (Chord Step) ......................... 100 Entering miscellaneous characters (marks) ............................ 46 Entering numbers ................................................................. 46 Entering special character marks (umlaut, accent, Japanese “ ” and “ ”) ......................... 46 Entering Your Name and Language Preference ................... 143 Equal Temperament............................................................ 128 ESEQ .................................................................................. 151 Example Keyboard Data ..................................................... 149 [EXIT] button .................................................................. 18, 41 exit from small pop-up windows .......................................... 41 [EXTRA TRACKS (STYLE)] button .................................... 18, 78 F Fade In Time, Fade Out Time, Fade Out Hold Time ........... 140 [FADE IN / OUT] button................................................. 18, 66 FAVORITE ............................................................................ 72 [FF] button ..................................................................... 18, 77 File ....................................................................................... 40 File/Folder-related Operations .............................................. 42 Files/folders in a floppy disk ................................................. 43 Fill........................................................................................ 67 Filter..................................................................... 91, 108, 121 FINGERED ........................................................................... 63 FINGERED ON BASS............................................................ 63 First Key On ....................................................................... 102 FLOPPY DISK drive .............................................................. 40 Floppy disk drive .............................................................. 19, 6 Follow Lights ........................................................................ 79 Foot Controller ............................................................. 59, 146 Footswitch.................................................................... 59, 146 Formatting a Disk ............................................................... 142 [FREEZE] button...................................................... 19, 87, 134 FULL KEYBOARD................................................................. 63 [FUNCTION] button .................................................... 18, 125 G Gate Time ............................................................................ 98 GENRE ........................................................................... 71, 73 GENRE NAME ...................................................................... 73 GM System Level 1....................................................... 19, 152 Groove ............................................................................... 114 162 CVP-205/203 Groove parameters .............................................................114 [GUIDE] button ........................................................14, 18, 79 H Handling the Floppy Disk Drive (FDD) and Floppy Disk.........6 Harmonic Content ................................................................91 HARMONY ............................................................59, 92, 135 Harmony Assignments ........................................................136 Harmony Types ..................................................................136 [HARMONY / ECHO] button ..........................................19, 59 Headphones .................................................................17, 144 Help messages can be displayed in any one of the following languages...........................................................50 [HELP] button .................................................................18, 50 High Key.............................................................................118 [HOST SELECT] switch .................................................19, 146 Hz ......................................................................................127 I ICON SELECT .......................................................................47 [INPUT VOLUME] knob ...............................................19, 144 Inputting and Editing Lyrics.................................................108 Instant Selection of Displays .................................................48 INTRO ..................................................................................67 [INTRO] button.........................................................18, 31, 65 K Karao-Key .............................................................................79 Key cover..............................................................................16 KEY SIGNATURE ..................................................................82 Keyboard guide lamps ....................................................19, 79 Keyboard Percussion.............................................................56 Keyboard Touch .................................................................133 Keyboard/Panel...................................................................133 KEYWORD .....................................................................71, 72 Kirnberger...........................................................................128 L Layer.....................................................................................57 Layering Two Different Voices ..............................................57 LCD ......................................................................................15 [LCD CONTRAST] knob .................................................18, 17 Left .......................................................................................58 LEFT CH. ..............................................................................82 [LEFT HOLD] button.......................................................19, 59 Left pedal........................................................................19, 59 Live! .....................................................................................56 Local Control ......................................................................137 Loop recording ...................................................................109 Lyrics ............................................................................84, 108 M MAIN A/B/C/D......................................................................65 MAIN [A] button.............................................................18, 65 MAIN [B] button .............................................................18, 65 MAIN [C] button.............................................................18, 65 MAIN [D] button ............................................................18, 65 Maintaining Panel Settings ..................................................134 Maintenance...........................................................................8 Making Global and Other Important Settings ......................125 Making Overall System Settings (Local Control, Clock, etc.) ... 137 Making Settings for Fade In/Out, Metronome, Parameter Lock, and Tap .................................................140 Making Settings for the Display, Speaker System, and Voice Number Indication .........................................141 Index Making Settings for the Pedals ............................................ 131 Making Settings for the Pedals and Keyboard ..................... 131 Making Style File Format Settings ....................................... 117 Master Tune ....................................................................... 127 Mastering Your Favorite Songs.............................................. 38 [MASTER VOLUME] dial ................................................ 18, 17 Mean-Tone......................................................................... 128 Measure/Beat/Clock ............................................................. 98 [MEMORY] button.......................................................... 19, 85 Message Switch .................................................................. 138 Messages ................................................................................ 8 Metronome ........................................................................ 140 METRONOME [START / STOP] button ........................... 18, 51 [MIC. LINE] switch ....................................................... 19, 144 [MIC. LINE IN] jack ...................................................... 19, 144 MIDI .................................................................................. 137 MIDI [THRU] [OUT] [IN] terminals.............................. 19, 146 MIDI channels.................................................................... 150 MIDI IN.............................................................................. 146 MIDI OUT.......................................................................... 146 MIDI Receive Parts ............................................................. 139 MIDI SET UP ...................................................................... 143 MIDI terminals ................................................................... 146 MIDI THRU........................................................................ 146 Mix .................................................................................... 104 [MIXING CONSOLE] button......................................... 18, 119 [MONO] button ............................................................. 19, 59 Moving Files/Folders ............................................................ 43 MULTI FINGER .................................................................... 63 Multi Recording ................................................................... 95 [MUSIC FINDER] button .................................... 15, 19, 33, 70 Music Finder Record Edit ..................................................... 72 Music Finder Search ............................................................. 71 Music Stand ......................................................................... 16 Muting Specific Parts ............................................................ 78 N NAME .................................................................................. 42 Naming Files/Folders ............................................................ 42 Natural Voices ..................................................................... 89 Natural!................................................................................ 56 NEW (FOLDER) .................................................................... 45 NEW RECORD ..................................................................... 73 [NEXT] button .......................................................... 18, 41, 47 Normal............................................................................... 102 Note Events ........................................................................ 106 Note for Windows users (regarding MIDI driver)................. 146 Note Limit .......................................................................... 118 NOTE NAME........................................................................ 83 NTR (Note Transposition Rule) ........................................... 117 NTT (Note Transposition Table).......................................... 118 O OCTAVE ............................................................................ 121 One Touch Setting ............................................................... 32 ONE TOUCH SETTING [1] - [4] buttons .................. 19, 68, 69 One-touch Piano Play .......................................................... 56 [ON / OFF] button (POWER) .......................................... 18, 17 Open/Save displays .............................................................. 39 Organizing Files by Creating a New Folder .......................... 45 Other Parameters in the Basic Display................................ 112 Other Playback-related Operations....................................... 77 Other Settings..................................................................... 140 [OTS LINK] button.......................................................... 18, 69 Outputting the sound of an external device through the built-in speakers of the Clavinova ............................................... 145 Overdub recording .............................................................109 Owner ................................................................................143 P Pad .......................................................................................95 Parameter ...........................................................................117 Parameter Lock ...................................................................141 PASTE .............................................................................43, 44 Pedal ..................................................................................131 Pedal (Center) .......................................................................59 Pedal (Left)............................................................................59 Pedal (Right) .........................................................................59 Pedal-controllable Functions...............................................132 [PHONES] jacks............................................................19, 144 Phrase...................................................................................95 Phrase Mark..................................................................77, 129 [PIANO] button ........................................................15, 19, 56 PIANO (SOUND CREATOR).................................................90 Piano Lock function ..............................................................56 PITCH BEND RANGE .........................................................121 Pitch settings for each scale ................................................128 Playback of Songs .................................................................21 Playing a style.................................................................28, 60 Playing a Style’s Rhythm Channels only................................62 Playing Along with the Clavinova .........................................36 Playing and Practicing with the Songs...................................36 Playing Back Songs on Disk ..................................................77 Playing Different Voices with the Left and Right Hands.........27 Playing Fill-in patterns automatically when changing accompaniment sections ...................................................67 Playing Several Sounds Simultaneously.................................57 Playing Styles........................................................................28 Playing the Demos..........................................................20, 53 Playing the Internal Songs .....................................................75 Playing the sounds of the Clavinova through an external audio system, and recording the sounds to an external recorder ........................................................145 Playing Two Voices Simultaneously......................................26 Playing Voices ......................................................................25 PORTAMENTO TIME..........................................................121 Practice Functions.................................................................79 Practicing Music with the Guide Functions ...........................80 PRESET drive.........................................................................40 Preset MIDI Templates ........................................................137 Punch In/Out ......................................................................102 Pure Major..........................................................................128 Pure Minor..........................................................................128 Pythagorean........................................................................128 Q QUANTIZE ...........................................................................82 Quantize.....................................................................103, 116 Quantize Size .....................................................................103 Quick Recording...................................................................94 Quick Start..........................................................................129 R Realtime Recording.............................................................111 Realtime Recording Characteristics .....................................109 [REC] button ...................................................................18, 93 Rec Mode ...........................................................................102 Recalling a Registration Memory Setup .................................87 Recalling the Registered Settings ...........................................87 Receive...............................................................................139 Receive Transpose ..............................................................138 Receiving MIDI Data ..........................................................139 CVP-205/203 163 Index SAVE .................................................................................... 45 Save ............................................................................... 39, 45 Saving Files .......................................................................... 45 Saving Your Registration Memory Setups.............................. 86 Scale .................................................................................. 128 Scale Tune ......................................................................... 127 Score (CVP-205 only) ........................................................... 81 Searching the Ideal Setups .................................................... 71 Searching the Music Finder Records ..................................... 34 Section button indications — [BREAK], [INTRO], [MAIN], [ENDING] buttons ............................................................ 65 sections ................................................................................ 30 Select the Recording Options: Starting, Stopping, Punching In/Out ............................................................. 102 Selecting a Scale ................................................................ 127 Selecting a Voice.................................................................. 55 Selecting Files and Folders ................................................... 41 Selecting Intro and Ending Types .......................................... 67 Selecting items ..................................................................... 47 Selecting the Freeze Settings................................................. 87 Sequence Format................................................................ 151 sequencer........................................................................... 149 Set Up ................................................................................ 105 Setting Auto Accompaniment-related Parameters ............... 130 Setting Chord Channels ...................................................... 139 Setting Harmony and Echo ................................................. 135 Setting Root Note Channels ................................................ 139 Setting Separate Voices for the Left and Right Sections of the Keyboard ................................................................ 58 Setting Song-related Parameters.......................................... 129 Setting the Fingering Method .............................................. 131 Setting the Level Balance and Voice ................................... 120 Setting the MIDI Parameters ............................................... 137 Setting the Registration Sequence, Freeze, and Voice Set ... 134 Setting the volume................................................................ 17 SFX....................................................................................... 56 164 CVP-205/203 T Tap Count...........................................................................141 [TAP TEMPO] button ......................................................18, 52 TEMPO [E] [ ] buttons..............................................18, 51 TEMPO FROM......................................................................71 Tempo Indications — MAIN Display ....................................52 TEMPO TO ...........................................................................71 [TO HOST] terminal .......................................15, 19, 146, 147 [TOP] button...................................................................18, 77 [TRACK 1 (R)] button ......................................................18, 78 [TRACK 2 (L)] button.......................................................18, 78 Transmit..............................................................................138 Transmit Clock....................................................................138 Transmitting MIDI Data ......................................................138 TRANSPOSE [E] [ ] buttons ....................................18, 133 Transpose Assign ................................................................133 Tune ...................................................................................121 TUNING.............................................................................121 Tuning the Overall Pitch .....................................................127 E S Sheet Music Braces (CVP-205 only) ......................................16 Showing the Clavinova Display on a TV .....................136, 145 Simultaneously Playing a Song and an Accompaniment Style........................................................76 SINGLE FINGER....................................................................63 SMF (Standard MIDI File) ....................................................151 Song ...............................................................................14, 74 SONG [START / STOP] button ........................................18, 75 SONG AUTO REVOICE......................................................120 Song Book ......................................................................22, 74 Song Creator .........................................................................93 Song Playback ..........................................................21, 74, 75 Song Recording.....................................................................93 Song Settings.......................................................................129 Sostenuto pedal ..............................................................19, 59 SOUND (SOUND CREATOR)...............................................90 SOUND CREATOR Parameters.............................................89 [SOUND CREATOR] button ...........................................18, 88 Source Root/Chord..............................................................117 Specifying the Order for Calling Up Registration Memory Presets .............................................................................134 SPEED...................................................................................91 Split Point ...........................................................................130 Step Record ..........................................................................97 Step Record (Chord)............................................................100 Step Record (Note)................................................................99 Step Recording....................................................................112 Stopping the Style Playback While Releasing Keys................66 Style................................................................................14, 60 STYLE [START / STOP] button.........................................18, 61 Style Creator .......................................................................109 Style File .......................................................................19, 151 Style File Format .................................................................110 Style Sections........................................................................30 Style Setting ........................................................................130 sustain ..................................................................................91 Sweet!...................................................................................56 [SYNC.START] button .....................................................18, 61 [SYNC.STOP] button.......................................................18, 66 SYS/EX. (System Exclusive) ..................................................107 System ................................................................................137 System Events .....................................................................107 System Messages.................................................................150 System Reset .......................................................................143 SYSTEM SET UP..................................................................143 E record .................................................................................. 70 Recording............................................................................. 37 Recording Chord Changes for the Auto Accompaniment .... 100 Recording Individual Notes .................................................. 97 Recording Melodies ............................................................. 99 Recording Your Performances and Creating Songs................ 93 Registering Panel Setups ....................................................... 85 Registering the Panel Controls in One Touch Setting ............ 69 REGISTRATION BANK ......................................................... 86 REGISTRATION EDIT display ............................................... 86 Registration Memory ............................................................ 85 REGISTRATION MEMORY [1] – [8] buttons ................... 19, 85 Registration Sequence ........................................................ 134 Regular Voices ..................................................................... 89 RELEASE ............................................................................... 91 Remove Event .................................................................... 116 Repeat Playback of a Specific Range .................................... 78 [REPEAT] button ............................................................. 18, 78 Replace ................................................................................ 72 Resonance............................................................................ 91 Restoring the Factory-programmed Settings of the CVP-205/203 ........................................................ 143 [REVERB] button............................................................. 18, 58 Reverb................................................................................ 124 [REW] button ................................................................. 18, 77 Rhythm ................................................................................ 95 RIGHT CH. .......................................................................... 82 Root ................................................................................... 139 RTR (Retrigger Rule) ........................................................... 118 Index U UP........................................................................................ 45 USER drive ........................................................................... 40 USER EFFECT ............................................................. 123, 143 Using the USB terminal on your computer with a USB/MIDI interface (UX256, etc.) .................................................... 148 Using Your Clavinova with Other Devices ......................... 144 Utility ................................................................................. 140 V [VARIATION] button ...................................................... 19, 58 Velocity........................................................................ 98, 115 Velocity Change ................................................................. 116 VIBRATO ............................................................................. 91 [VIDEO OUT] jack ............................................... 19, 136, 145 Voice Allocation Format..................................................... 152 VOICE buttons ......................................................... 15, 19, 55 Voice Characteristics ............................................................ 56 Voice Effects......................................................................... 58 VOICE PART ON / OFF [LAYER] button ......................... 18, 57 VOICE PART ON / OFF [LEFT] button ............................ 18, 57 Voice Set ............................................................................ 135 Volume/Voice .................................................................... 120 W Werckmeister ..................................................................... 128 What You Can Do With MIDI ............................................ 150 What’s MIDI? ..................................................................... 148 X XF ................................................................................ 19, 151 XG ............................................................................... 19, 152 CVP-205/203 165 IMPORTANT SAFETY INSTRUCTIONS INFORMATION RELATING TO PERSONAL INJURY, ELECTRICAL SHOCK, AND FIRE HAZARD POSSIBILITIES HAS BEEN INCLUDED IN THIS LIST. WARNING- When using any electrical or electronic product, basic precautions should always be followed. These precautions include, but are not limited to, the following: 1. Read all Safety Instructions, Installation Instructions, Special Message Section items, and any Assembly Instructions found in this manual BEFORE making any connections, including connection to the main supply. 2. Main Power Supply Verification: Yamaha products are manufactured specifically for the supply voltage in the area where they are to be sold. If you should move, or if any doubt exists about the supply voltage in your area, please contact your dealer for supply voltage verification and (if applicable) instructions. The required supply voltage is printed on the name plate. For name plate location, please refer to the graphic found in the Special Message Section of this manual. 3. This product may be equipped with a polarized plug (one blade wider than the other). If you are unable to insert the plug into the outlet, turn the plug over and try again. If the problem persists, contact an electrician to have the obsolete outlet replaced. Do NOT defeat the safety purpose of the plug. 4. Some electronic products utilize external power supplies or adapters. Do NOT connect this type of product to any power supply or adapter other than one described in the owners manual, on the name plate, or specifically recommended by Yamaha. 5. WARNING: Do not place this product or any other objects on the power cord or place it in a position where anyone could walk on, trip over, or roll anything over power or connecting cords of any kind. The use of an extension cord is not recommended! If you must use an extension cord, the minimum wire size for a 25’ cord (or less) is 18 AWG. NOTE: The smaller the AWG number, the larger the current handling capacity. For longer extension cords, consult a local electrician. 6. Ventilation: Electronic products, unless specifically designed for enclosed installations, should be placed in locations that do not interfere with proper ventilation. If instructions for enclosed installations are not provided, it must be assumed that unobstructed ventilation is required. 7. Temperature considerations: Electronic products should be installed in locations that do not significantly contribute to their operating temperature. Placement of this product close to heat sources such as; radiators, heat registers and other devices that produce heat should be avoided. 8. This product was NOT designed for use in wet/damp locations and should not be used near water or exposed to rain. Examples of wet/damp locations are; near a swimming pool, spa, tub, sink, or wet basement. 9. This product should be used only with the components supplied or; a cart, rack, or stand that is recommended by the manufacturer. If a cart, rack, or stand is used, please observe all safety markings and instructions that accompany the accessory product. 10. The power supply cord (plug) should be disconnected from the outlet when electronic products are to be left unused for extended periods of time. Cords should also be disconnected when there is a high probability of lightning and/or electrical storm activity. 11. Care should be taken that objects do not fall and liquids are not spilled into the enclosure through any openings that may exist. 12. Electrical/electronic products should be serviced by a qualified service person when: a. The power supply cord has been damaged; or b. Objects have fallen, been inserted, or liquids have been spilled into the enclosure through openings; or c. The product has been exposed to rain: or d. The product dose not operate, exhibits a marked change in performance; or e. The product has been dropped, or the enclosure of the product has been damaged. 13. Do not attempt to service this product beyond that described in the user-maintenance instructions. All other servicing should be referred to qualified service personnel. 14. This product, either alone or in combination with an amplifier and headphones or speaker/s, may be capable of producing sound levels that could cause permanent hearing loss. DO NOT operate for a long period of time at a high volume level or at a level that is uncomfortable. If you experience any hearing loss or ringing in the ears, you should consult an audiologist. IMPORTANT: The louder the sound, the shorter the time period before damage occurs. 15. Some Yamaha products may have benches and/or accessory mounting fixtures that are either supplied as a part of the product or as optional accessories. Some of these items are designed to be dealer assembled or installed. Please make sure that benches are stable and any optional fixtures (where applicable) are well secured BEFORE using. Benches supplied by Yamaha are designed for seating only. No other uses are recommended. PLEASE KEEP THIS MANUAL 92-469-2 FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA. 3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/ uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference. Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to co-axial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America, Electronic Service Division, 6600 Orangethorpe Ave, Buena Park, CA90620 The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries. * This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. IMPORTANT NOTICE FOR THE UNITED KINGDOM Connecting the Plug and Cord IMPORTANT. The wires in this mains lead are coloured in accordance with the following code: BLUE : NEUTRAL BROWN : LIVE As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured makings identifying the terminals in your plug proceed as follows: The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. Making sure that neither core is connected to the earth terminal of the three pin plug. (2 wires) • This applies only to products distributed by Yamaha-Kemble Music (U.K.) Ltd. CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND. (polarity) • This applies only to products distributed by Yamaha Canada Music Ltd. • Ceci ne s’applique qu’aux produits distribués par Yamaha Canada Musique Ltée. (class B) For details of products, please contact your nearest Yamaha or the authorized distributor listed below. Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante. NORTH AMERICA CANADA Yamaha Canada Music Ltd. 135 Milner Avenue, Scarborough, Ontario, M1S 3R1, Canada Tel: 416-298-1311 U.S.A. Yamaha Corporation of America 6600 Orangethorpe Ave., Buena Park, Calif. 90620, U.S.A. Tel: 714-522-9011 CENTRAL & SOUTH AMERICA MEXICO Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen Bestimmungsländern erhältlich. Para detalles sobre productos, contacte su tienda Yamaha más cercana o el distribuidor autorizado que se lista debajo. ASIA FRANCE Yamaha Musique France, Division Claviers BP 70-77312 Marne-la-Vallée Cedex 2, France Tel: 01-64-61-4000 ITALY Yamaha Musica Italia S.P.A. Viale Italia 88, 20020 Lainate (Milano), Italy Tel: 02-935-771 SPAIN/PORTUGAL Yamaha-Hazen Electronica Musical, S.A. Ctra. de la Coruna km. 17, 200, 28230 Las Rozas (Madrid) Spain Tel: 91-201-0700 GREECE Yamaha de Mexico S.A. De C.V., Departamento de ventas Javier Rojo Gomez No.1149, Col. Gpe Del Moral, Deleg. Iztapalapa, 09300 Mexico, D.F. Tel: 686-00-33 BRAZIL Yamaha Musical do Brasil LTDA. Av. Rebouças 2636, São Paulo, Brasil Tel: 011-853-1377 ARGENTINA Philippe Nakas S.A. Navarinou Street 13, P.Code 10680, Athens, Greece Tel: 01-364-7111 SWEDEN PANAMA AND OTHER LATIN AMERICAN COUNTRIES/ CARIBBEAN COUNTRIES Yamaha de Panamá S.A. Torre Banco General, Piso 7, Urbanización Marbella, Calle 47 y Aquilino de la Guardia, Ciudad de Panamá, Panamá Tel: 507-269-5311 EUROPE THE UNITED KINGDOM Yamaha-Kemble Music (U.K.) Ltd. Sherbourne Drive, Tilbrook, Milton Keynes, MK7 8BL, England Tel: 01908-366700 IRELAND Danfay Ltd. 61D, Sallynoggin Road, Dun Laoghaire, Co. Dublin Tel: 01-2859177 GERMANY/SWITZERLAND Yamaha Europa GmbH. Siemensstraße 22-34, 25462 Rellingen, F.R. of Germany Tel: 04101-3030 AUSTRIA Yamaha Music Austria Schleiergasse 20, A-1100 Wien Austria Tel: 01-60203900 THE NETHERLANDS Yamaha Music Nederland Kanaalweg 18G, 3526KL, Utrecht, The Netherlands Tel: 030-2828411 BELGIUM Yamaha Music Belgium Keiberg Imperiastraat 8, 1930 Zaventem, Belgium Tel: 02-7258220 Tom Lee Music Co., Ltd. 11/F., Silvercord Tower 1, 30 Canton Road, Tsimshatsui, Kowloon, Hong Kong Tel: 2737-7688 INDONESIA PT. Yamaha Music Indonesia (Distributor) PT. Nusantik Gedung Yamaha Music Center, Jalan Jend. Gatot Subroto Kav. 4, Jakarta 12930, Indonesia Tel: 21-520-2577 KOREA Yamaha Music Korea Ltd. Tong-Yang Securities Bldg. 16F 23-8 Yoido-dong, Youngdungpo-ku, Seoul, Korea Tel: 02-3770-0661 MALAYSIA Yamaha Music Malaysia, Sdn., Bhd. Lot 8, Jalan Perbandaran, 47301 Kelana Jaya, Petaling Jaya, Selangor, Malaysia Tel: 3-703-0900 Yamaha Scandinavia AB J. A. Wettergrens Gata 1 Box 30053 S-400 43 Göteborg, Sweden Tel: 031 89 34 00 PHILIPPINES DENMARK Yamaha de Panamá S.A. Sucursal de Argentina Viamonte 1145 Piso2-B 1053, Buenos Aires, Argentina Tel: 1-4371-7021 HONG KONG YS Copenhagen Liaison Office Generatorvej 8B DK-2730 Herlev, Denmark Tel: 44 92 49 00 FINLAND F-Musiikki Oy Kluuvikatu 6, P.O. Box 260, SF-00101 Helsinki, Finland Tel: 09 618511 Yupangco Music Corporation 339 Gil J. Puyat Avenue, P.O. Box 885 MCPO, Makati, Metro Manila, Philippines Tel: 819-7551 SINGAPORE Yamaha Music Asia Pte., Ltd. 11 Ubi Road #06-00, Meiban Industrial Building, Singapore Tel: 65-747-4374 TAIWAN NORWAY Norsk filial av Yamaha Scandinavia AB Grini Næringspark 1 N-1345 Østerås, Norway Tel: 67 16 77 70 ICELAND Skifan HF Skeifan 17 P.O. Box 8120 IS-128 Reykjavik, Iceland Tel: 525 5000 OTHER EUROPEAN COUNTRIES Yamaha Europa GmbH. Siemensstraße 22-34, 25462 Rellingen, F.R. of Germany Tel: 04101-3030 Yamaha KHS Music Co., Ltd. 10F, 150, Tun-Hwa Northroad, Taipei, Taiwan, R.O.C. Tel: 02-2713-8999 THAILAND Siam Music Yamaha Co., Ltd. 121/60-61 RS Tower 17th Floor, Ratchadaphisek RD., Dindaeng, Bangkok 10320, Thailand Tel: 02-641-2951 THE PEOPLE’S REPUBLIC OF CHINA AND OTHER ASIAN COUNTRIES Yamaha Corporation, Asia-Pacific Music Marketing Group Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650 Tel: 053-460-2317 AFRICA Yamaha Corporation, Asia-Pacific Music Marketing Group Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650 Tel: 053-460-2312 MIDDLE EAST TURKEY/CYPRUS Yamaha Europa GmbH. Siemensstraße 22-34, 25462 Rellingen, F.R. of Germany Tel: 04101-3030 OTHER COUNTRIES Yamaha Music Gulf FZE LB21-128 Jebel Ali Freezone P.O.Box 17328, Dubai, U.A.E. Tel: 971-4-881-5868 OCEANIA AUSTRALIA Yamaha Music Australia Pty. Ltd. Level 1, 99 Queensbridge Street, Southbank, Victoria 3006, Australia Tel: 3-9693-5111 NEW ZEALAND Music Houses of N.Z. Ltd. 146/148 Captain Springs Road, Te Papapa, Auckland, New Zealand Tel: 9-634-0099 COUNTRIES AND TRUST TERRITORIES IN PACIFIC OCEAN Yamaha Corporation, Asia-Pacific Music Marketing Group Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650 Tel: 053-460-2312 HEAD OFFICE Yamaha Corporation, Pro Audio & Digital Musical Instrument Division Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650 Tel: 053-460-3273 [CL] 23 Clavinova Web site (English only) http://www.yamahaclavinova.com/ Yamaha Manual Library (English version only) http://www2.yamaha.co.jp/manual/english/ M.D.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation © 2001 Yamaha Corporation Printed in Indonesia ??????? ???AP???.?-03C0