Yamaha PX10 Handleiding

Merk: Yamaha

Model: PX10

Type: Handleiding

Deze handleiding is ook geschikt voor

Reference Manual

PX10/PX8/PX5/PX3 Reference Manual

Contents

Introduction 3

Features ....................................................................3

Manuals for PX amplifier ...........................................3

Usage examples .......................................................4

Use with two full-range speakers .........................4

Use with a full-range speaker and subwoofer......4

Use with a full-range speaker

driven in bi-amp mode ......................................5

Use for driving a subwoofer with a stereo signal

...5

PX amplifier available system configurations.......6

Signal processing in PX amplifier ........................7

Input sensitivity and amplifier gain .......................7

Controls and functions 8

Front panel ................................................................8

Rear panel.................................................................9

Setup 10

Setup procedure......................................................10

Rack mounting ........................................................11

Speaker connection ................................................11

Connecting to the [SPEAKERS] terminal...........11

Panel Operation 12

Basic operation .......................................................12

Basic mode and Advanced mode ......................12

Screen structure......................................................13

Alert messages .......................................................14

Panel lock................................................................14

HOME screen..........................................................15

CONFIG VIEW screen ........................................... 16

MENU screen ......................................................... 17

MENU screen types .......................................... 17

Operation .......................................................... 17

Operation tree ................................................... 18

CONFIG WIZARD screen (Basic mode) ................ 20

SP TYPE (speaker type) ................................... 20

SP SERIES (speaker series) ............................ 20

SP MODEL (speaker model)............................. 20

HPF (high pass filter) ........................................ 21

LPF (low pass filter) .......................................... 21

X-OVER (crossover) ......................................... 21

CONFIRMATION .............................................. 21

CONFIG WIZARD screen (Advanced mode) ......... 22

WIZARD MODE ................................................ 22

SP TYPE (speaker type) ................................... 22

ROUTING.......................................................... 23

SENS./GAIN (input sensitivity/amplifier gain) ... 24

SP SERIES (speaker series) ............................ 24

SP MODEL (speaker model)............................. 24

SP IMPEDANCE (speaker impedance) ............ 24

CONFIRMATION .............................................. 24

TUNING screen...................................................... 25

D-CONTOUR .................................................... 25

DELAY .............................................................. 26

X-OVER (crossover) ......................................... 26

HPF (high pass filter) ........................................ 27

LPF (low pass filter) .......................................... 27

POLARITY (speaker polarity)............................ 28

SP DELAY......................................................... 28

EQ (6 Band PEQ).............................................. 29

LEVEL (output level) ......................................... 29

LIMITER ............................................................ 30

CHANNEL LINK ................................................ 30

CHANNEL COPY .............................................. 30

SAVE/LOAD ...................................................... 31

AMP PRESET screen............................................. 32

RECALL ............................................................ 32

STORE .............................................................. 32

CLEAR .............................................................. 32

TITLE................................................................. 33

PROTECT ......................................................... 33

UTILITY screen ...................................................... 34

PANEL SETUP.................................................. 34

PANEL LOCK.................................................... 34

HOME SCREEN (HOME screen)...................... 35

IMPORT SP PRESET

(import speaker preset) ................................. 35

DEVICE BACKUP ............................................. 36

DEVICE INFORMATION ................................... 36

INITIALIZE......................................................... 36

LOG................................................................... 37

Initializing the PX amplifier ..................................... 37

Reference 39

Function list ............................................................ 39

Message list............................................................ 42

Troubleshooting...................................................... 44

General specifications ............................................ 46

Block diagram......................................................... 48

Dimensions............................................................. 49

Current draw and thermal dissipation..................... 50

Index....................................................................... 54

PX10/PX8/PX5/PX3 Reference Manual

Introduction

Thank you for your purchase of the Yamaha PX10, PX8, PX5 or PX3 power amplifier. Please read through this manual carefully before using for the first time,

in order to take full advantage of your PX power amplifier’s superlative features and enjoy trouble-free operation for years to come.

• Please read the Precautions in the PX10/PX8/PX5/PX3 Owner’s Manual before use.

• The illustrations as shown in this manual are for instructional purposes only.

• The company names and product names used in this manual are the trademarks or registered trademarks of their respective companies.

• In this manual, the PX10, PX8, PX5 and PX3 power amplifier models are referred to collectively as “PX amplifier.”

• Unless specified otherwise, the example illustrations used in this manual are taken from the PX10.

• The bitmap fonts used in this instrument have been provided by and are the property of Ricoh Co., Ltd.

• Maximum output of 1,000W (PX10), from an exceptionally lightweight chassis.

• Yamaha’s proprietary Class-D and processing technologies provide superb sound qual-

ity and high reliability.

• Speaker presets that allow you to get the best possible performance from Yamaha

speakers.

• A wide variety of DSP functions, including D-CONTOUR processing.

• Configuration Wizard that allows easy, optimal configuration for any speaker system.

• Broad range of input/output connectors.

• Owner’s Manual (included with the product)

Explains installation and basic operation.

• Reference Manual (this file)

Explains all required matters for setup and operation.

• Technical Specifications (included with the product)

Describes detailed specifications such as numerical values, dimensions, etc.

Features Manuals for PX amplifier

Introduction — Usage examples

PX10/PX8/PX5/PX3 Reference Manual

PX amplifiers can be used for various applications.

 Use with two full-range speakers

This conventional application inputs stereo L/R signals to each channel (A/B) for stereo reproduction with two speakers.

 Use with a full-range speaker and subwoofer

The input signal is divided into separate frequency ranges for driving a full-range speaker and subwoofer.

Usage examples

Introduction — Usage examples

PX10/PX8/PX5/PX3 Reference Manual

 Use with a full-range speaker driven in bi-amp mode

The input signal is divided into separate frequency ranges for driving a two-way full-range speaker in bi-amp mode.

 Use for driving a subwoofer with a stereo signal

Stereo input signals drive a subwoofer in Power Boost mode (PX5 and PX3 only)

Channel A + Channel B

(PX5)

Introduction — Usage examples

PX10/PX8/PX5/PX3 Reference Manual

 PX amplifier available system configurations

PX amplifier can be used with the following 15 types of system configurations, including the examples above.

Input configuration (routing)

Dual mode Parallel mode Single mode Sum mode

Channel A and channel B are

independent.

After dividing channel A input

signal to channel A and channel B,

the signal is processed.

After processing channel A input

signal, the signal is divided to A and

channel B.

Mixes input signals from

channel A and channel B.

Two full-range speakers

Two subwoofers

A full-range speaker and a subwoofer

A full-range speaker

driven in bi-amp mode

Full-range speaker

Power Boost

mode

Subwoofer

NOTE

In Power Boost mode, the two-channel amplifiers are used as one-channel, high-power amplifier (PX5 and PX3 only).

Output combination (speaker type)

Introduction — Usage examples

PX10/PX8/PX5/PX3 Reference Manual

 Signal processing in PX amplifier

The PX amplifier gives you comprehensive control over the sound with input processors and speaker processors. The signals from the input connectors are processed in input processors

equipped in each input connectors. The processed signals are added or divided depending on the set routing, processed finally with the speaker processor in each channel, and output from the

[SPEAKERS] terminals.

Refer to “TUNING screen” (page 25) in “Panel Operation” for details on the processing.

 Input sensitivity and amplifier gain

The PX amplifier specifies the input sensitivity/amplifier gain from two input sensitivities or two amplifier gains. Input sensitivity controls the input signal level so that the amplifier can output

the maximum power. If signals over the input sensitivity are input, the built-in limiter of the PX amplifier is activated. If the volume is lowered, the input sensitivity rises and the amplifier gain

declines. Maximum power is constant if the volume is lowered.

For example, if the amplifier gain on the PX10 is set to 32 dB, the input sensitivity is +9.3 dBu and the maximum output power is 1,000 W (if speaker impedance is 8Ω). When the volume is not

lowered (0 dB), output power of 1,000 W results with +9.3 dBu input.

When the volume on the PX10 is lowered to 6 dB, the input sensitivity is +15.3 dBu (9.3 dBu + 6 dBu) and the amplifier gain is 26 dB (32 dB - 6 dB). If a +15.3 dBu signal is input, maximum

output power of 1,000 W is gained.

D-Contour

Delay

HPF LPF Polarity

Speaker

Delay

Level Limiter

6 Band

PEQ

Input processor Speaker processor

Amplifier gain 26 dB

Volume 6 dB

Amplifier gain 32 dB

Maximum output power 41.3 dBu

(1000 W, 8Ω)

Input sensitivity +15.3 dBu

Input sensitivity +9.3 dBu

PX10/PX8/PX5/PX3 Reference Manual

Controls and functions

q Power button

Turns the power to the unit on or off.

w [POWER] indicator

Lights when the power is on.

e [ALERT] indicator

Lights when a problem in the device is detected, and contin-

ues to light until the cause of the problem is solved.

r [USB] indicator

Lights when a compatible USB flash drive is inserted into the

[USB] terminal.

Flashes when the USB flash drive is being accessed.

t [CLIP/LIMIT] indicator

Lights when the limiter is operating to protect the amplifier and

the speaker, or when the input signal overflows in the digital

circuit or clips at the amplifier output.

y [SIGNAL] indicator

Lights when the output is greater than -60 dB of maximum

output level (8 ohms).

u [PROTECT] indicator

Lights when the protection circuit is operating.

i Display

Displays the status of the PX amplifier and setting menus.

For details, refer to “Screen structure” (page 13).

o [MENU] key

Press this to move to the top MENU screen.

!0 [] (Back) key

Press this to move up to the immediately higher menu level or

previous display. Press and briefly hold the key to return the

HOME screen.

!1 Main knob

Rotate this to change the value of parameters and move the

position of cursor. Press the knob to actually enter the set

value or enable the selected item.

!2 [A]/[B] key

Press this to change the values of parameters and move the

cursor position.

!3 [USB] terminal

Insert a USB flash drive to read/load the data from/to the PX

amplifier.

!4 Volume knob

Adjusts the level from -∞ dB to 0 dB.

If “ROUTING” is set to something other than “DUAL,” adjust

the output balance with the volume knob of channel B.

!5 Intake ports

Air intakes for the cooling fan. Make sure to not block these ports.

Front panel

!2 !2

o !0

!5 !5

WARNING

To ensure that high-volume noise is not output from the

speakers, power-on the equipment starting with the audio

sources, then the mixer and processors, and finally the

amplifiers. Reverse this order when turning the system off.

NOTE

Details of the problem are shown on the display (i).

Selecting the [ ] icon on the “HOME screen” (page 15) with the

main knob calls up the operating log.

NOTICE

Do not unplug the USB flash drive while the [USB] indicator is

flashing. Doing so may cause data in the PX amplifier or USB

flash drive to be corrupted or lost.

NOTE

• The settings can be changed so that the display and indicators

turn off automatically when panel is not operated (Black-out sta-

tus: page 34).

• For protection of the display, if there is no operation for one min-

ute, the display automatically darkens; if unoperated for 20 min-

utes, it automatically turns off. To turn on the display again,

simply press any key on the front panel or rotate any knob.

NOTE

Press the main knob and [A] key to change the mute status of

channel A. Press the main knob and [B] key to change the mute

status of channel B.

NOTICE

When the [USB] terminal is not used, attach the included USB cap

to protect the terminal.

NOTE

The [USB] terminal is used in the following cases:

• Loading speaker preset: IMPORT SP PRESET (page 35)

• Writing operation log: LOG (page 37)

• Device backup: DEVICE BACKUP (page 36)

• Saving/loading SP TUNING DATA: SAVE/LOAD (page 31)

Controls and functions — Rear panel

PX10/PX8/PX5/PX3 Reference Manual

!6 [INPUT] A/B connectors

Two types of input connectors are provided for both channels

A and B. In Single mode or Parallel mode, the input connec-

tors of channel A are used.

• XLR jack

XLR type 3-31 jack.

The polarity is shown below (IEC60268).

• Phone jack

Balanced TRS phone jack.

The polarity of the connections is shown below.

!7 [SPEAKERS] A/B terminals

Output terminals for speakers. Three types are available

(below).

• Neutrik NL4MD speakON connector

• Binding post connector

• Phone jack

!8 [AC IN] connector

Connect the supplied AC power cord. First connect the AC

power cord to the connector on the amplifier, and then plug it

into an appropriate AC power outlet. Secure the AC power

cord with the AC plug clamp to prevent accidental disconnec-

tion from the connector.

!9 Exhaust ports

Exhaust vents for the cooling fan. Make sure to not block

these ports.

Rear panel

!8!6

NOTE

The XLR input jack and the phones input jack of each channel are

connected in parallel. The signal input from an XLR jack can be

output from the phone jack and input to another amplifier. Only

one of the jacks can be used as an input jack at one time; the sig-

nals from the jacks cannot be mixed.

Ground

Cold

Hot

Ring (cold)

Tip (hot)Sleeve (ground)

NOTICE

• Do not touch the terminals or metal parts of cords connected to

the terminal. If connecting speakers to multiple connectors of

the same channel results in a parallel connection, make sure

that the total impedance of the speakers to be connected is not

excessively low.

• The PX amplifier adopts BTL (Balanced Transformer Less)

amplifier circuits. Connecting both terminals of channel A and

channel B and contact between the terminal and the chassis

may cause a failure or malfunction. Be careful not to connect or

contact the two by mistake.

NOTE

In Power Boost mode, the output terminals of channel A are used

(PX5/PX3 only).

qwe

Installing the AC plug clamp

PX10/PX8/PX5/PX3 Reference Manual

Setup

1. Set the PX amplifier in the desired loca-

tion.

If the device is to be mounted in a rack, refer to “Rack

mounting” (page 11).

2. Lower the two volume knobs to the mini-

mum.

3. Connect speakers to the [SPEAKERS]

terminals.

Refer to “Speaker connection” (page 11).

4. Connect outputs from sources, such as

a mixer, to the [INPUT] connectors.

5. Connect the power cord to the [AC IN]

connector.

Secure the AC power cord with the AC plug clamp to

prevent accidental disconnection from the connector.

6. Turn on the device.

7. Set up the system configuration with the

Configuration Wizard.

Though the PX amplifier can be used as a normal ampli-

fier by simply setting the volume knobs properly, using

the Configuration Wizard to make settings enhances the

performance of speakers.

Refer to “CONFIG WIZARD screen (Basic mode)”

(page 20) or “CONFIG WIZARD screen (Advanced

mode)” (page 22).

8. Rotate the volume knob to adjust the vol-

ume.

9. Control the tone in TUNING screen.

Refer to “TUNING screen” (page 25). In this condition,

the device is available.

Setup procedure

WARNING

To ensure that high-volume noise is not output from the

speakers, power-on the equipment starting with the

audio sources, then the mixer and processors, and

finally the amplifiers. Reverse this order when turning

the system off.

To A C p o w e r

outlet

Power cord

AC IN connector

Installing the AC plug clamp

qwe

Setup — Rack mounting

PX10/PX8/PX5/PX3 Reference Manual

The PX amplifier can be mounted in an EIA standard rack

(2U size).

Rack mounting

Precautions for rack mounting

This device is rated for operation at ambient tempera-

tures ranging from 0° to 40°C. When mounting the device

with other device(s) in an EIA standard equipment rack,

internal temperatures can exceed the specified upper

limit, resulting in impaired performance or failure. When

rack mounting the device, always observe the following

requirements to avoid heat buildup:

• When mounting the unit in a rack with devices such as

power amplifiers that generate a significant amount of

heat, leave more than 1U of space between the device

and other equipment. Also, either leave the open

spaces uncovered or install appropriate ventilating pan-

els to minimize the possibility of heat buildup. Multiple

PX amplifiers can be mounted by stacking vertically.

• To ensure sufficient airflow, leave the rear of the rack

open and position it at least 10 centimeters from walls

or other surfaces. If the rear of the rack cannot be left

open, install a commercially available fan or similar ven-

tilating option to secure sufficient airflow. If you have

installed a fan kit, there may be cases in which closing

the rear of the rack will produce a greater cooling effect.

Refer to the rack and/or fan unit manual for details.

 Connecting to the [SPEAKERS] termi-

nal

 Binding post connector

• Without plugs

Remove about 15 mm of insulation from the end of

each speaker cable, pass the bare wire through the holes

in the appropriate speaker terminals, and tighten the ter-

minals to securely clamp the wires. Make sure that the

bare wire ends do not jut out from the terminals and

touch the chassis.

• Y-plugs

From above, insert the Y-plugs all the way into the

opening, and tighten the terminal.

 speakON connector

Insert the speakON cable plug (Neutrik NL4) into the

connector, and turn it to the right to lock it.

Speaker connection

CAUTION

Make sure that the power is turned off, to avoid the dan-

ger of electrical shock.

15 mm

0.25"

(6.3 mm)

≤0.51"

(12.9 mm)

1–

2–

Channel A

Neutrik NL4 PX amplifier

1+ A+

1– A–

2+ B+

2– B–

Channel B

Neutrik NL4 PX amplifier

1+ B+

1– B–

2+ (not connected)

2– (not connected)

PX10/PX8/PX5/PX3 Reference Manual

Panel Operation

 Basic mode and Advanced mode

The PX amplifier provides two setting methods: Basic mode and Advanced mode.

Basic mode is convenient since it lets you use the device quickly and easily with minimum

settings. Advanced mode is used when you want to set parameters in detail.

Each mode has a HOME screen and MENU screen.

Example of screens

 To switch between Basic mode and Advanced mode

1. Press the [MENU] key to enter the MENU screen.

2. Rotate the main knob to select the tab of the desired mode, and

then press the main knob.

Basic operation

HOME screen (Basic mode) MENU screen (Advanced mode)

• BASIC:

Basic mode

• ADVANCED:

Advanced mode

Panel Operation — Screen structure

PX10/PX8/PX5/PX3 Reference Manual

The screens of the PX amplifier differ depending on the selected mode, Basic or Advanced. The HOME screen and the CONFIG WIZARD screen in the MENU screen are in both modes, but dis-

played items differ. To switch between the modes, use the OPERATION MODE screen in the MENU screen.

Screen structure

Basic mode

HOME screen

CONFIG VIEW screen

MENU screen

MENU top screen

CONFIG WIZARD screen

TUNING screen

AMP PRESET screen

UTILITY screen

Advanced mode

HOME screen

CONFIG VIEW screen

MENU top screen

CONFIG WIZARD screen

TUNING screen

AMP PRESET screen

UTILITY screen

MENU screen

 BASIC

ADVANCED 

Panel Operation — Alert messages

PX10/PX8/PX5/PX3 Reference Manual

If an abnormality occurs in the PX amplifier, the [ALERT] indicator lights and an alert mes-

sage appear on the display. Refer to the “Message list” (page 42) at the end of the book for

details on each alert.

To prevent changes being made to the PX amplifier by mistake, use the panel lock function.

This allows you to set a PIN code (a 4-digit identification number).

Refer to “UTILITY screen” – “PANEL LOCK” (page 34) for instructions.

 To release the panel lock

If the panel controls are operated while the panel is locked, the following message appears

in the display.

To release the panel lock, input the PIN code by rotating the main knob, select “OK,” and

then press the main knob.

Alert messages Panel lock

NOTE

• To release the panel lock temporarily, select “TEMP.” If “TEMP” is selected, the panel will be

locked after turning off and turning on again.

• If a PIN code has been set, input the appropriate PIN code (set previously).

NOTE

If the volume knob is operated when the panel is locked with “ALL,” the following screen appears when

the lock is released. Rotate the volume knob to match the actual value. The value of the volume can-

not be changed unless the values match.

Actual value Value of the volume

Panel Operation — HOME screen

PX10/PX8/PX5/PX3 Reference Manual

q Mute indication

Appears when the signal is muted.

w Volume indication

Shows the settings of the volume knobs.

In Power Boost mode, only channel A setting is shown.

e VOL/BAL/GAIN indication

Shows what appears at the volume indications (w).

•VOL: Input volume

•BAL: Output balance

•GAIN: Total level (gain from the input jack to the speaker output terminal)

r Level meter

Shows input or output level.

t Threshold indication

Indicates the thresholds of the limiter on the output level of the speaker processors with

“>” and “<” while the level meter shows the input level.

y D-CONTOUR indication

Shows the status of D-CONTOUR.

•OFF: Nothing appears.

• FOH/MAIN: “FOH” appears.

• MONITOR: “MONI” appears.

u Delay indication

Shows the delay time. When delay is off, nothing appears.

i Polarity indication

Appears when the polarity is inverted.

o Filter indication

Shows the cutoff frequency of the filter. When the filter is off, nothing appears.

!0 EQ indication

Appears when the EQ is on.

!1 CONFIG VIEW icon

CONFIG VIEW screen appears when selecting the icon by rotating the main knob and

pressing it.

!2 [ ] icon

Operation log appears when selecting the icon by rotating the main knob and pressing it.

Refer to “Operation log indication” (page 37) for details on the operation log.

!3 Speaker name, clipping/limiting message

Normally, this shows the name of the speaker that is connected, along with a related mes-

sage if clipping or limiting has occurred.

HOME screen

NOTE

Displayed content depends on the input configuration (routing).

• In Dual mode: Input volume at both channels A and B.

• Other than Dual mode: Input volume at channel A, output balance at channel B.

(In Power Boost mode, only channel A is shown.)

Set at “dB VALUE” (page 35) in UTILITY screen–HOME SCREEN screen, which is shown in VOL/

BAL/GAIN indication, input volume or total gain.

NOTE

Input and output can be switched from [HOME SCREEN] (page 35) in the UTILITY screen.

!1o i o u !2!0

NOTE

The displayed speaker name is the speaker preset recalled with the Configuration Wizard.

NOTE

Rotate the main knob to select the group of D-CONTOUR, delay, polarity and filter indications, and

then press the main knob to call up the TUNING screen.

Panel Operation — CONFIG VIEW screen

PX10/PX8/PX5/PX3 Reference Manual

Called up by pressing the main knob when the HOME screen is shown.

The current settings are listed.

q System configuration: page 6

w Input sensitivity/amplifier gain: page 24

e HPF cutoff frequency for channel A: pages21, 27

r LPF cutoff frequency for channel A: pages21, 27

t HPF cutoff frequency for channel B: pages21, 27

y LPF cutoff frequency for channel B: pages21, 27

u System configuration: page 6

i Input sensitivity/amplifier gain: page 24

o HPF cutoff frequency for channel A: pages21, 27

!0 Crossover frequency: pages21, 26

!1 LPF cutoff frequency for channel B: pages21, 27

!2 Polarity: page 28

To return to the HOME screen, press the [ ] (back) key.

To call up the CONFIG WIZARD screen, press the main knob when the CONFIG VIEW

screen appears.

CONFIG VIEW screen

e r

o !0 !1

Panel Operation — MENU screen

PX10/PX8/PX5/PX3 Reference Manual

Sets the basic condition of the device.

 MENU screen types

The following MENU screens are available.

• CONFIG WIZARD screen (Basic mode) (Advanced mode)

• TUNING screen

• AMP PRESET screen

• UTILITY screen

 Operation

 To display the MENU screen:

Press the [MENU] key in the HOME screen.

 To move to the lower layer in MENU screens, or to select a param-

eter or other item:

Rotate the main knob to move to the desired item, and then press the main knob.

 To move to the upper layer in MENU screens:

Press the [ ] (back) key.

 To return to the HOME screen:

Press and hold the [ ] (back) key.

MENU screen

NOTE

Refer to the “Function list” (page 39) for details on configurable items in each MENU screen.

NOTE

The layer of the displayed screen is shown at the top of the screen.

MENU top screen HPF screen

Parameter edit screenTUNING screen

Panel Operation — MENU screen

PX10/PX8/PX5/PX3 Reference Manual

 Operation tree

Category Subcategory Function

Basic

mode

Advanced

mode

Details

CONFIG WIZARD

(Basic mode)

SP TYPE Selects a combination of speakers for connection.  page 20

SP SERIES Selects a series of speakers for connection.  page 20

SP MODEL Selects a speaker for connection.  page 20

HPF Selects the cutoff frequency of the HPF. Common to channels A and B.  page 21

LPF Selects a cutoff frequency of the LPF. Common to channels A and B.  page 21

X-OVER Selects a crossover frequency of the full-range speaker and the subwoofer.  page 21

CONFIRMATION Applies the set value.  page 21

CONFIG WIZARD

(Advanced mode)

WIZARD MODE Selects the editing method: changing the current setting or making a new setting.  page 22

SP TYPE Selects a combination of speakers for connection.  page 22

ROUTING Selects the route of the input signal.  page 23

SENS./GAIN Sets the input sensitivity or the amplifier gain.  page 24

SP SERIES Selects a series of speakers for connection.  page 24

SP MODEL Selects a speaker for connection.  page 24

SP IMPEDANCE Sets the impedance of the speaker for connection.  page 24

CONFIRMATION Applies the set value.  page 24

TUNING

D-CONTOUR Sets the frequency character appropriately for usage of the speaker for connection. page 25

DELAY Sets the delay time to compensate the distance between speakers.  page 26

X-OVER Sets the crossover frequency. page 26

HPF Sets the high pass filter. *  page 27

LPF Sets the low pass filter *  page 27

POLARITY Set the polarity. page 28

SP DELAY Sets the delay time of the speaker processor.  page 28

EQ Edits 6 Band PEQ settings.  page 29

LEVEL Sets the output level.  page 29

LIMITER Sets the limiter.  page 30

CHANNEL LINK Links the parameter setting of channels A and B.  page 30

CHANNEL COPY Copies settings between channels.  page 30

SAVE/LOAD Saves or loads SP TUNING DATA via a USB flash drive.  page 31

* Only for some functions.

Panel Operation — MENU screen

PX10/PX8/PX5/PX3 Reference Manual

AMP PRESET

RECALL Recalls a setting. page 32

STORE Stores the setting. page 32

CLEAR Clears the setting. page 32

TITLE Edits the title of the setting. page 33

PROTECT Protects the setting against inadvertent changes. page 33

UTILITY

PANEL SETUP Sets the front panel indication method. *  page 34

PANEL LOCK Sets the panel lock. page 34

HOME SCREEN Sets contents of the HOME screen.  page 35

IMPORT SP PRESET Loads speaker preset data stored in the USB flash drive to the PX amplifier. page 35

DEVICE BACKUP Stores all the settings of the PX amplifier or restore the stored settings.  page 36

DEVICE INFORMATION Displays the condition in the device. page 36

INITIALIZE Displays how to initialize the data in the PX amplifier on the display. page 36

LOG Displays or writes the operating log.  page 37

* Only for some functions.

Category Subcategory Function

Basic

mode

Advanced

mode

Details

Panel Operation — CONFIG WIZARD screen (Basic mode)

PX10/PX8/PX5/PX3 Reference Manual

Using the Configuration Wizard enables you to easily set basic functions.

 SP TYPE (speaker type)

Selects the combination of the speakers for connection.

• FULL + FULL:

When connecting full-range speakers to the [SPEAKERS] terminals of both channels A

and B.

• SUB + SUB:

When connecting subwoofers to the [SPEAKERS] terminals of both channels A and B.

• FULL + SUB:

When connecting a full-range speaker to the [SPEAKER] terminal of channel B and a

subwoofer to the [SPEAKER] terminal of channel A.

 SP SERIES (speaker series)

Selects a speaker series for connection from models registered in the PX amplifier.

 SP MODEL (speaker model)

Specifies a speaker for connection from the speaker series selected in the SP SERIES

screen.

CONFIG WIZARD screen (Basic mode)

WARNING

The volume changes depending on the setting. Carry this out with the volume lowered for

safety.

NOTE

Items that can be set differ between Basic mode and Advanced mode. To make detailed settings,

switch to Advanced mode. Refer to “To switch between Basic mode and Advanced mode” (page 12)

for switching the mode.

NOTE

When a speaker is selected, filters, speaker impedance, and threshold of the limiter are set auto-

matically. If the speaker for connection is not in the menu, select “GENERIC.”

Panel Operation — CONFIG WIZARD screen (Basic mode)

PX10/PX8/PX5/PX3 Reference Manual

 HPF (high pass filter)

(If “SP SERIES” is “GENERIC”)

Selects the cutoff frequency of the HPF. Common to both channels A and B.

 LPF (low pass filter)

(If “AMP MODE” is “SUB+SUB” and “SP SERIES” is “GENERIC”)

Selects the cutoff frequency of the LPF. Common to both channels A and B.

 X-OVER (crossover)

(If “AMP MODE” is “FULL+SUB” and “SP SERIES” is “GENERIC”)

Selects the crossover frequency of the full-range speaker and subwoofer.

 CONFIRMATION

Applies the set value.

After confirming the setting is appropriate, press the main knob to actually apply the set

value.

To correct the setting, press the [ ] (back) key to return to the screen to be corrected.

To cancel the setting, press the [MENU] key or press and hold the [ ] (back) key until a

confirmation screen appears.

NOTE

In Basic mode, the filter type is fixed to 24 dB/Oct., Butterworth type.

NOTE

In Basic mode, the filter type is fixed to 24 dB/Oct., Butterworth type.

NOTE

In Basic mode, the filter type is fixed to 24 dB/Oct., Linkwitz Riley type.

Panel Operation — CONFIG WIZARD screen (Advanced mode)

PX10/PX8/PX5/PX3 Reference Manual

Using the Configuration Wizard here enables you to easily set more advanced functions.

 WIZARD MODE

Select a parameter status to start settings.

• EDIT CONFIG:

Changing the current setting

• NEW CONFIG:

Making a new setting

 SP TYPE (speaker type)

Selects a combination of speakers for connection.

• FULL+FULL:

When connecting full-range speakers to the [SPEAKERS] terminals of both channels A

and B.

• SUB+SUB:

When connecting subwoofers to the [SPEAKERS] terminals of both channels A and B.

• FULL+SUB:

When connecting a full-range speaker to the [SPEAKERS] of channel B and a subwoofer

to channel A.

•BI-AMP:

When connecting low range of a bi-amp speaker to the [SPEAKERS] of channel A and

high range to channel B.

• FULL (MONO):

When connecting a full-range speaker driven in Power Boost mode to the [SPEAKERS]

terminal of channel A (PX5 and PX3 only).

• SUB (MONO):

When connecting a subwoofer driven in Power Boost mode to the [SPEAKERS] terminal

of channel A (PX5 and PX3 only).

CONFIG WIZARD screen (Advanced mode)

WARNING

The volume changes depending on the setting. Carry this out with the volume lowered for

safety.

NOTE

To return to a previous parameter setting, press the [ ] (back) key.

NOTE

Refer to “PX amplifier available system configurations” (page 6) for details on combinations listed

in “ROUTING” (page 23).

Panel Operation — CONFIG WIZARD screen (Advanced mode)

PX10/PX8/PX5/PX3 Reference Manual

 ROUTING

Selects the route of the input signal from four types: DUAL, PARALLEL, SINGLE, and

SUM.

• DUAL (Dual mode):

Sends the input signal from channel A to speaker A, and sends the input signal from

channel B to speaker B.

• PARALLEL (Parallel mode):

Sends the input signal from channel A to both speaker A and speaker B. Channel A and

channel B can be set differently.

• SINGLE (Single mode):

Sends only the input signal from channel A.

• SUM (Sum mode):

Mixes and sends the input signals from channel A and channel B.

[SPEAKERS] A

[SPEAKERS] B

[INPUT] A

[INPUT] B

VOL

Input

processor A

Speaker

processor A

Input

processor B

Speaker

processor B

[INPUT] A

[INPUT] B

Input

processor A

Speaker

processor A

Input

processor B

Speaker

processor B

VOL

BAL

[SPEAKERS] A

[SPEAKERS] B

NOTE

The volume knob is available only for control of channel A. The volume of channel B is linked to

that of channel A.

NOTE

• Depending on the SP TYPE (speaker type, page 22), the menu choices may be limited. For

details, refer to “PX amplifier available system configurations” (page 6).

• Regarding input processors and speaker processors, refer to “Signal processing in PX amplifier”

(page 7). For setting instructions, refer to “TUNING screen” (page 25).

[INPUT] A

[INPUT] B

Input

processor A

Speaker

processor A

Speaker

processor B

VOL

BAL

[SPEAKERS] A

[SPEAKERS] B

[INPUT] A

[INPUT] B

Input

processor A

Speaker

processor A

Input

processor B

Speaker

processor B

BAL

[SPEAKERS] A

[SPEAKERS] B

VOL

Panel Operation — CONFIG WIZARD screen (Advanced mode)

PX10/PX8/PX5/PX3 Reference Manual

 SENS./GAIN (input sensitivity/amplifier gain)

Sets the input sensitivity or the amplifier gain.

You can select the input sensitivity(+4 dBu or +14 dBu), or the amplifier gain (26 dB or 32

dB).

 SP SERIES (speaker series)

Selects a speaker series for connection from models registered in the PX amplifier.

 SP MODEL (speaker model)

Specifies a speaker for connection from the speaker series selected in SP SERIES screen.

 SP IMPEDANCE (speaker impedance)

(If “SP SERIES” is “GENERIC”)

Sets the impedance of the speaker for connection.

When connecting speakers in parallel, set this parameter by a single speaker's impedance.

 CONFIRMATION

Applies the set value.

After confirming the setting is appropriate, press the main knob to actually apply the set

value.

To change or correct the setting, press the [ ] (back) key to return to the previous screen.

To cancel the setting, press the [MENU] key or press and hold the [ ] (back) key until a

confirmation screen appears.

NOTE

Refer to “Input sensitivity and amplifier gain” (page 7) for details on input sensitivity and amplifier

gain.

NOTE

When a speaker is selected, filters, speaker impedance, and threshold of the limiter are set auto-

matically. If the speaker for connection is not in the menu, select “GENERIC.”

Panel Operation — TUNING screen

PX10/PX8/PX5/PX3 Reference Manual

Set input processors and speaker processors for acoustic adjustment.

 D-CONTOUR

Sets the frequency character appropriately for usage of the speaker for connection.

q MODE

Switches presets of D-CONTOUR. Selects from the following items:

•OFF:

Turns off D-CONTOUR.

• FOH/MAIN:

Boosts the high and low frequency components so that the frequency response is suit-

able for main speaker use.

• MONITOR:

Reduces the low frequency range, which could otherwise tend to be boomy if the

speaker is set directly on the floor. This enables you to hear mid and high frequency

ranges clearly when using as a floor monitor.

w DEPTH

Sets the degree of the effect. The larger the value, the deeper the effect.

TUNING screen

NOTE

• If “A” or “B” appears in a parameter setting screen at the upper side in TUNING screen, the parame-

ter is for the respective channel, A or B.

• Press the [A] key or [B] key to select the desired channel for setting.

D-Contour

HPF LPF Polarity Level Limiter

6 Band

PEQ

Delay

Speaker

Delay

Channel

 Input processor and speaker processor

Input processor Speaker processor

D-Contour

HPF LPF Polarity Level Limiter

6 Band

PEQ

Delay

Speaker

Delay

Channel

Input processor Speaker processor

Panel Operation — TUNING screen

PX10/PX8/PX5/PX3 Reference Manual

 DELAY

(Advanced mode only)

Sets the delay time to compensate the distance between speakers. Sets according to ether

time or distance.

q ON/OFF

Turns the delay on/off.

w TIME [ms]

Sets the delay time in milliseconds.

e DISTANCE [m / feet]

Sets the delay time by physical distance (in meters or in feet).

 X-OVER (crossover)

(If “SP TYPE” is “FULL+SUB” or “BI-AMP”)

Sets the crossover frequency of channel A and channel B.

q X-OVER FREQ.

Sets the crossover frequency. The crossover frequency to be set is the cutoff frequencies

of the LPF of channel A and the HPF of channel B.

NOTE

Three delay time indications change in conjunction.

D-Contour

HPF LPF Polarity Level Limiter

6 Band

PEQ

Delay

Speaker

Delay

Channel

Input processor Speaker processor

D-Contour

HPF LPF Polarity Level Limiter

6 Band

PEQ

Delay

Speaker

Delay

Channel

Input processor Speaker processor

Low pass filter High pass filterCrossover frequency

Frequency

Panel Operation — TUNING screen

PX10/PX8/PX5/PX3 Reference Manual

 HPF (high pass filter)

Sets the high pass filter.

q ON/OFF

(Basic mode only)

Turn on/off the filter.

w TYPE (filter type)

(Advanced mode only)

Selects the attenuation per octave and the filter type.

e FREQ (Cutoff frequency)

Sets the cutoff frequency of the HPF.

r Gc (Cutoff gain)

(Advanced mode only)

Sets the gain at the cutoff frequency if “AdjustGc” (Adjustable Gc) is selected in “HPF

TYPE.”

 LPF (low pass filter)

Sets the low pass filter.

q ON/OFF

(Basic mode only)

Turns the filter on/off.

w TYPE (filter type)

(Advanced mode only)

Selects the attenuation per octave and the filter type.

e FREQ (Cutoff frequency)

Sets the cutoff frequency of the LPF.

r Gc (Cutoff gain)

(Advanced mode only)

Sets the gain at the cutoff frequency if “AdjustGc” (Adjustable Gc) is selected in “LPF

TYPE.”

NOTE

• If “THRU” is selected, filter is off.

• A filter on 12 db/Oct or more can be selected from four types (below): Adjustable Gain Con-

trol, Butterworth, Bessel, and Linkwitz Riley.

For example, the 12 dB/Oct. Butterworth type is displayed as “12dB BUT.”

D-Contour

HPF LPF Polarity Level Limiter

6 Band

PEQ

Delay

Speaker

Delay

Input processor Speaker processor

Basic mode

Channel Channel

Advanced mode

Filter type Display

Adjustable Gain Control ADJGc

Butterworth BUT

Bessel BESSL

Linkwitz Riley L-R

NOTE

• If “THRU” is selected, filter is off.

• A filter of 12 db/Oct or more can be selected from four types (below): Adjustable Gain Con-

trol, Butterworth, Bessel, and Linkwitz Riley.

For example, the 12 dB/Oct. Butterworth type is displayed as “12dB BUT.”

D-Contour

HPF LPF Polarity Level Limiter

6 Band

PEQ

Delay

Speaker

Delay

Input processor Speaker processor

Basic mode

Channel Channel

Advanced mode

Filter type Display

Adjustable Gain Control ADJGc

Butterworth BUT

Bessel BESSL

Linkwitz Riley L-R

Panel Operation — TUNING screen

PX10/PX8/PX5/PX3 Reference Manual

 POLARITY (speaker polarity)

Sets the polarity in order to avoid volume problems due to phase interference between the

speakers.

q POLARITY

When “NORMAL” is selected, the polarity is normal; when “INVERTED” is selected,

the polarity is inverted.

 SP DELAY

(Advanced mode only)

Edits the speaker delay time of the speaker processor.

Sets according to ether time or distance.

q ON/OFF

Turns the speaker delay on/off.

w TIME [ms]

Sets the delay time in milliseconds.

e DISTANCE [m / feet]

Sets the delay time by physical distance (in meters or in feet).

D-Contour

HPF LPF

Polarity

Level Limiter

6 Band

PEQ

Delay

Speaker

Delay

Input processor Speaker processor

Channel

NOTE

Three delay time indications change in conjunction.

D-Contour

HPF LPF Polarity Level Limiter

6 Band

PEQ

Delay

Speaker

Delay

Channel

Input processor Speaker processor

Panel Operation — TUNING screen

PX10/PX8/PX5/PX3 Reference Manual

 EQ (6 Band PEQ)

(Advanced mode only)

Edits 6 Band PEQ parameters of the speaker processor.

q CHANNEL button

Shows the target channel of the EQ. Use the [A] / [B] keys to select the target channel.

When EQ settings are linked, it shows A+B.

Move the cursor to the button and then press the knob to link the EQ settings.

w ON/OFF

Turns the 6 Band PEQ on/off. When set to off, the EQ characteristics display is shown

only in outline.

e FLAT

Sets the gain parameter of all bands to 0 dB.

r Band 1 – 6

Selects a single Band for calling up the corresponding parameters. Press the knob on

the selected band to move the cursor to a parameter area.

t Parameter area

Displays parameters of each Band. Move the cursor to a parameter name, and press the

knob to edit the parameter value. Press the [ ] (back) key to return the cursor to the

parameter name. Press again to return the cursor to the Band.

 LEVEL (output level)

(Advanced mode only)

Sets the output level to balance the output levels of channels.

q LEVEL

Sets the output levels in 0.1 dB increments.

NOTE

The EQ link works independently from the channel link. The EQ link is available for any chan-

nel type.

D-Contour

HPF LPF Polarity Level Limiter

6 Band

PEQ

Delay

Speaker

Delay

Input processor Speaker processor

D-Contour

HPF LPF Polarity Level Limiter

6 Band

PEQ

Delay

Speaker

Delay

Channel

Input processor Speaker processor

Panel Operation — TUNING screen

PX10/PX8/PX5/PX3 Reference Manual

 LIMITER

(Advanced mode only)

For changing the settings of the limiter depending on the speaker specifications, in order to

protect the speaker.

q ON/OFF

Turns the limiter on/off.

w THRESHOLD

Sets the threshold beyond which the limiter is activated according to output power

(Watt).

e IMPEDANCE (Ω/UNIT)

Sets the impedance of the speaker for connection (16Ω, 12Ω, 8Ω, or 4Ω).

When connecting speakers in parallel, set this parameter by a single speaker's imped-

ance.

 CHANNEL LINK

(Advanced mode only, if “SP TYPE” is “FULL+FULL” or “SUB+SUB”)

Links the parameter setting of channel A and channel B.

q ON/OFF

When the setting is changed from off to on, the device initially makes the settings of

channel A and channel B identical. If a setting is operated for channel A, the settings of

channel A are copied to the settings of channel B. If a setting is operated for channel B,

the settings of channel B are copied to the settings of channel A.

 CHANNEL COPY

(Advanced mode only; when “SP TYPE” is set to “FULL+FULL” or

“SUB+SUB”)

Copies settings between channels.

q Ach –> Bch

Copies the settings of channel A to channel B.

w Bch –> Ach

Copies the settings of channel B to channel A.

NOTE

• When a speaker is selected with Configuration Wizard, “THRESHOLD” is automatically set.

• When connecting speakers in parallel, set this parameter according to the specified output

power for a single speaker.

D-Contour

Delay

HPF LPF Polarity

Speaker

Delay

Level Limiter

6 Band

PEQ

Channel

Input processor Speaker processor

Channel

Panel Operation — TUNING screen

PX10/PX8/PX5/PX3 Reference Manual

 SAVE/LOAD

(Advanced mode only)

You can save/load SP TUNING DATA by using an USB flash drive.

q SAVE SP TUNING

Saves the setting file to the USB flash drive.

Select this menu to display the file name screen. Rotate the main knob to select the

position for inputting the character and press the main knob to switch to character entry.

Then rotate the main knob to select the character to be input and press the main knob to

actually enter it. By pressing the [ ] (back) key in the character entry mode, you can

return to position selection. Selecting “OK” in this state confirms the title. Selecting

“OK” in the confirmation screen saves the setting file. Finally select “OK” to return to

the previous screen.

w LOAD SP TUNING

Loads the setting file in the USB flash drive.

Select this menu to display the list of files. Rotate the main knob to select a file, and

then press the main knob to display the confirmation. Press “OK” to start loading. After

loading is complete, a confirmation message will appear. Press “OK” to return to the

previous screen.

NOTE

• You can enter up to sixteen alphanumeric characters.

• Available characters include ASCII types and some symbols.

Channel

NOTE

• Files which have file name over sixteen characters are not shown in the list.

• File names containing unavailable characters on the PX unit are not displayed.

Panel Operation — AMP PRESET screen

PX10/PX8/PX5/PX3 Reference Manual

PX amplifier settings that are set in CONFIG WIZARD screen and D-CONTOUR screen can

be stored as amplifier preset. Eight amplifier presets can be stored in a PX amplifier.

Select the number of the desired amplifier preset by rotating the main knob and pressing it.

The operation selection screen appears.

 RECALL

Recalls a stored amplifier preset. The current speaker preset and the speaker preset of the

selected amplifier preset appear.

 STORE

Stores the current PX amplifier setting to an amplifier preset, and allows you to name it.

Rotate the main knob to select the position to input the character and press the main knob

to switch to character entry. Then rotate the main knob to select the character to be input

and press the main knob to actually enter it.

By pressing the [ ] (back) key in the character entry mode, you can return to selecting

the position. Selecting “OK” in this state confirms the title.

 CLEAR

Clears a stored amplifier preset.

AMP PRESET screen

WARNING

If a speaker type different from the current one is recalled, the volume will change signifi-

cantly. Carry this out with the volume lowered for safety.

NOTE

The PX10/PX8 cannot recall an amplifier preset stored on the PX5/PX3 in the Power Boost mode.

Protected amplifier

preset

Currently selected

amplifier preset

Current speaker type

Speaker type of selected

amplifier preset

NOTE

A protected amplifier preset cannot be overwritten.

NOTE

A protected amplifier preset or the currently selected amplifier preset cannot be cleared.

Cursor when selecting

the position

Cursor when selecting

the character

Panel Operation — AMP PRESET screen

PX10/PX8/PX5/PX3 Reference Manual

 TITLE

Edits a title of a stored amplifier preset.

Rotate the main knob to select the position to input the character and press the main knob

to switch to character entry. Then rotate the main knob to select the character to be input

and press the main knob to actually enter it.

By pressing the [ ] (back) key when selecting the character, you can return to selecting

the position. Selecting “OK” in this state confirms the title.

 PROTECT

Protects a stored amplifier preset against inadvertent changes. If the parameter is on, the

amplifier preset cannot be with the TITLE, CLEAR, and overwriting STORE operations.

NOTE

The title of a protected amplifier preset cannot be edited.

Cursor when selecting

the position

Cursor when selecting

the character

Panel Operation — UTILITY screen

PX10/PX8/PX5/PX3 Reference Manual

Sets up the status of PX amplifier, stores data to the USB flash drive, and loads data from the

USB flash drive.

 PANEL SETUP

Sets the front panel indication method.

q BRIGHTNESS

Sets the brightness of the back light of the display.

w BLACKOUT

(Advanced mode only)

If the panel is not operated for 10 seconds, the indication of the display turns off (Black-

out status).

 PANEL LOCK

Sets the panel lock not to operate the PX amplifier by mistake. At that time, a PIN code, 4-

digit identification number, can be set.

q PAN E L LOC K

Locks the front panel (panel lock). There are three available settings.

•OFF:Panel lock is off.

• LCD: Locks operations for indications of the display. Operation of the volume knob

and muting are available.

• ALL: No operations, except for release of the panel lock, are available.

w PIN CODE

Sets a PIN code (any four digits) for the panel lock. Once a PIN code has been set, the

PIN code must be entered to release the panel lock.

UTILITY screen

NOTE

• Even if “BLACKOUT” is on, the [POWER], [ALERT], [PROTECT], and [LIMIT] indicators light

as usual.

• Even if “BLACKOUT” is off, for protection of the display, if there is no operation for one min-

ute, the display automatically darkens; if unoperated for 20 minutes, it automatically turns off.

To turn on the display again, simply press any key on the front panel or rotate any knob.

NOTE

• Refer to “Panel Operation” – “Panel lock” (page 14) for instructions on releasing the panel

lock.

• If a PIN code has been set, the PIN code must be entered even when the setting of the panel

lock is changed “OFF” to “LCD” or “ALL.”

NOTE

• If you have forgotten the PIN code, you will need to initialize the device to release the PIN

code. Refer to “Initializing the PX amplifier” (page 37) for instructions on initializing.

• In the initialized state, the PIN code is set to “0000.” When the PIN code is set to “0000,” the

PIN code input is not needed to release the panel lock.

Panel Operation — UTILITY screen

PX10/PX8/PX5/PX3 Reference Manual

 To set a PIN code

1. Open the PIN code input screen.

In MENU screen–UTILITY screen–PANEL LOCK screen, select “PIN CODE”

(page 34).

The cursor is on the first digit of the PIN code.

2. Rotate the main knob to select a digit, and then press the main

knob to enter it.

After the digit is entered, the cursor moves to the next digit.

3. Enter the subsequent digits in the same way.

4. After inputting four digits, press the [OK] key.

The PIN code is entered.

 HOME SCREEN (HOME screen)

(Advanced mode only)

Sets contents of the HOME screen.

q dB VALUE

Select the value type in the VOL/BAL/GAIN indication in HOME screen (page 15).

•VOL: Input volume

• GAIN: Total level (gain from the input jack to the speaker output terminal)

w METER

Selects the level indicated in the level meter, input signal or output signal.

• INPUT: Input signal level

•OUTPUT: Output signal level

 IMPORT SP PRESET (import speaker preset)

Imports a speaker preset downloaded and stored in a USB flash drive to the PX amplifier.

q IMPORT FROM USB

Imports a speaker preset from a USB flash drive.

NOTE

While the PIN code is being input, you can correct it by pressing the [ ] (back) key and

selecting the desired digit with the main knob.

NOTE

If the PIN code is changed to “0000,” the PIN code is not set. In this state, PIN code input is

not needed to set or release the panel lock.

NOTE

Speaker presets can be downloaded from the Yamaha Pro Audio global website.

Panel Operation — UTILITY screen

PX10/PX8/PX5/PX3 Reference Manual

 DEVICE BACKUP

(Advanced mode only)

Save and restore all the settings in a PX amplifier to/from a USB flash drive. Use the func-

tion when you want to set multiple PX amplifiers to the same setting, or change to another

PX amplifier and keep the same settings.

q SAVE TO USB

Saves all the setting data in the device to a USB flash drive.

w RESTORE FROM USB

Restores setting data stored in a USB flash drive.

 DEVICE INFORMATION

Indicates the internal status of the PX amplifier.

q THERMAL PSU

Indicates the temperature of the power supply unit in three grades. If maximum is indi-

cated, the limiter is active.

w THERMAL AMP

Indicates the temperature of the amplifier unit in five grades. The limiter is active

depending on the temperature.

e RUN TIME

Indicates the total operating time of the device.

r FIRMWARE

Indicates the version of the firmware.

 INITIALIZE

Indicates how to initialize the internal data of the PX amplifier.

WARNING

If a speaker type different from the current one is recalled, the volume will change signifi-

cantly. Carry this out with the volume lowered for safety.

NOTE

The PX10/PX8 cannot recall settings stored on the PX5/PX3 in the Power Boost mode.

NOTE

Refer to “Initializing the PX amplifier” (page 37) for instructions on initializing.

Panel Operation — Initializing the PX amplifier

PX10/PX8/PX5/PX3 Reference Manual

 LOG

(Advanced mode only)

Indicates or saves the operation log in the PX amplifier.

q LOG LIST

Indicates the overall operation log stored in the PX amplifier.

The log is displayed in the order that events have occurred. The time information is dis-

played in “NNNN HHH:MM:SS” format, where the format represents the number of

hours (HHH)/minutes (MM)/seconds (SS) have elapsed since the (NNNN)

power-on.

• Operation log indication

Rotating the main knob (to select an event) and pressing the knob (to actually determine

the event) show the detailed view.

w SAVE TO USB

Save the latest operation log to a USB flash drive. The function is for user support refer-

ence.

There are three ways to initialize the PX amplifier.

 To initialize the current parameters

1. Turn on while pressing the [A] key.

2. Rotate the main knob to select “CONFIG+TUNING” and press

the main knob.

NOTE

The Operation log can also be called up by selecting and determining the [ ] icon by using

the main knob when the [ ] icon is shown in the HOME screen.

Initializing the PX amplifier

NOTE

Current parameters are parameters set in the CONFIG WIZARD, AMP PRESET, and TUNING

screens. For details, refer to “Function list” (page 39).

Panel Operation — Initializing the PX amplifier

PX10/PX8/PX5/PX3 Reference Manual

 To initialize all the user data

1. Turn on while pressing the [A] key.

2. Rotate the main knob to select “ALL” and press the main knob.

 To initialize all the user data and speaker preset

Turn on while pressing the [B] key and the [ ] (back) key simultaneously. Screens to

confirm the initialization do not appear.

NOTE

• User data are parameters set in the CONFIG WIZARD, AMP PRESET, TUNING, and UTILITY

screens. For parameters, refer to “Function list” (page 39).

• PIN code is also initialized.

NOTE

The operation log is not deleted.

PX10/PX8/PX5/PX3 Reference Manual

Reference

Function list

Parameter Initial value Basic mode Advanced mode

Amplifier preset

applied

CH LINK/

CH COPY applied

SP TUNING

DATA applied

Configuration

INPUT SENSITIVITY/GAIN +4 dBu (Not configurable)

Sensitivity: +4 dBu, +14 dBu

Gain: 32 dB, 26 dB



—

AMP MODE

SP TYPE FULL+FULL

• FULL+FULL

• SUB+SUB

• FULL+SUB

• FULL+FULL

• SUB+SUB

• FULL+SUB

• BI-AMP

• FULL (MONO) POWER BOOST

• SUB (MONO) POWER BOOST

ROUTING DUAL (Not configurable)

• DUAL

• PARALLEL

• SINGLE

• SUM

SPEAKER IMPEDANCE 8Ω (Not configurable) 4Ω, 8Ω, 12Ω, 16Ω 

Device

ATT — -∞ – 0 dB (31 steps)

——

MUTE OFF OFF, ON

Input processor

D-CONTOUR

MODE OFF OFF, FOH/MAIN, MONITOR



DEPTH 5 1 – 10

DELAY

ON/OFF OFF

(Not configurable)

OFF, ON

TIME (msec)

DISTANCE (meters)

DISTANCE (feet)

0 msec

0 m

0 ft

0 – 74.0 msec

0 – 25.4 m

0 – 83.4 ft

Reference — Function list

PX10/PX8/PX5/PX3 Reference Manual

Speaker

processor

X-OVER FREQ. 100 Hz 20.0 Hz – 20.0 kHz



HPF

TYPE 24 dB BUT OFF(THRU), ON (24 dB BUT) 20 types

FREQ. 20 Hz 20.0 Hz – 20.0 kHz

Gc -3 dB (Not configurable) -6 dB–+6 dB

LPF

TYPE THRU OFF(THRU), ON (24 dB BUT) 20 types

FREQ. 20 kHz 20.0 Hz – 20.0 kHz

Gc -3 dB (Not configurable) -6 dB – +6 dB

POLARITY NORMAL NORMAL, INVERTED



(CH COPY only)

SPEAKER DELAY OFF (Not configurable)

0.00 – 5.00 ms

0.000 – 1.716 meter

0.00 – 5.64 feet



EQ ON ON

(Not configurable)

OFF, ON

TYPE (×6) PEQ 10 types

BYPASS (×6) OFF OFF, ON

FREQ. (×6) Each Band

20.0 Hz – 20.0 kHz

GAIN (×6) 0 dB -18.0 dB – +18.0 dB

Q (×6) 4.2 63.0 – 0.1

LEVEL 0 dB (Not configurable) -10 dB – +10 dB



(CH COPY only)

LIMITER

ON/OFF OFF

(Not configurable)

OFF, ON



THRESHOLD 1500 W 10 – 1500 W

SP IMPEDANCE 8Ω 4Ω, 8Ω, 12Ω, 16Ω

ATTACK/RELEASE — Set in speaker preset

Utility

PA N EL

SETUP

BRIGHTNESS 6 1 – 10

———

BLACKOUT OFF (Not configurable) OFF, ON

PANEL LOCK

LOCK OFF OFF, LCD, ALL

PIN CODE 0000 4-digit (“0000” if not set)

HOME

SCREEN

dB VALUE VOL (Not configurable) VOL, GAIN

LEVEL METER OUTPUT (Not configurable) INPUT, OUTPUT

*1: THRU, 6dB/OCT, 12dB ADJGc, 12dB BUT, 12dB BESSL, 12dB L-R, 18dB ADJGc, 18dB BUT, 18dB BESSL, 24dB ADJGc, 24dB BUT, 24dB BESSL, 24dB L-R, 36dB ADJGc, 36dB BUT, 36dB BESSL, 48dB

ADJGc, 48dB BUT, 48dB BESSL, 48dB L-R

*2: PEQ, L.SHELF (6dB/Oct), L.SHELF (12dB/Oct), H.SHELF (6dB/Oct), H.SHELF (12dB/Oct), HPF, LPF, APF (1st), APF (2nd), Horn EQ

*3: 31.5 Hz, 100 Hz, 315 Hz, 1.0 kHz, 3.15 kHz, 10.0 kHz

Parameter Initial value Basic mode Advanced mode

Amplifier preset

applied

CH LINK/

CH COPY applied

SP TUNING

DATA applied

Reference — Function list

PX10/PX8/PX5/PX3 Reference Manual

Others

CH LINK — (Not available)  ———

AMP PRE-

SET

RECALL

—



(Total is 8)

———

STORE

CLEAR

TITLE

PROTECT

SP PRESET

RECALL (WIZARD)

—  ———

IMPORT FROM USB

DEVICE

BACKUP

SAVE TO USB

— (Not available)  ———

RESTORE FROM USB

DEVICE

INFORMA-

TION

THERMAL PSU

—  ———THERMAL AMP

FIRMWARE VERSION

LOG

LOGGING

—

 (4096)

———LOG LIST 

SAVE TO USB (Not available) 

INITIALIZE

CONFIG+TUNING

—  ———ALL

FACTORY DATA RESET

FIRMWARE UPDATE —  ———

Parameter Initial value Basic mode Advanced mode

Amplifier preset

applied

CH LINK/

CH COPY applied

SP TUNING

DATA applied

Reference — Message list

PX10/PX8/PX5/PX3 Reference Manual

Message list

Number Message Symptom Possible solution

01–06 SYSTEM ERROR The device has not started up correctly.

Turn the power off, and then turn back on after waiting at least 6 seconds. If this

does not solve the problem, initialize the memory (page 37). Should this also fail,

contact your Yamaha dealer.

07 SP PRESET DATA LOST The speaker preset file is corrupted.

Load the preset file again from a USB flash drive. If this does not solve the problem,

initialize the memory (page 37). Should this also fail, contact your Yamaha dealer.

08 WRONG SP PRESET DATA

The speaker preset data in the device are corrupted. Failure

might have occurred in loading a speaker preset file from the USB

flash drive.

Load the preset file again from a USB flash drive. If this does not solve the problem,

initialize the memory (page 37). Should this also fail, contact your Yamaha dealer.

20 OUTPUT CURRENT OVER [*]

Protection of the circuitry has been enabled in the device because

there is: 1) a short at a speaker terminal, amplifier terminal, or

wire; or 2) the amplifier load is excessive. (*: channel name)

Make sure that the speakers are not damaged and the total impedance is not too

low, and inspect the connection of the speaker cables.

21 AMP TEMP TOO HIGH

The temperature in the amplifier unit of has exceeded the allowed

limit. The output load is excessively high. This tends to occur

when the load of only channel A is high.

Since continuous high-power output causes high temperatures, lower the output

level. If the load is biased on the channel A, disperse the load by connecting to the

channel B or other amplifiers. Also, check whether dirt or a foreign object could

have clogged the cooling fan, and clean the fan itself if necessary.

22–24 LIMITED BY OVERHEAT

The amplifier temperature is excessively high, and so the limiter

for the output has been activated.

Since continuous high-power output causes high temperatures, lower the output

level. Also, check whether dirt or a foreign object could have clogged the cooling

fan, and clean the fan itself if necessary.

25 MUTED BY OVERHEAT

The amplifier temperature is excessively high, and so the output

level has been lowered.

Since continuous high-power output causes high temperatures, lower the output

level. Also, check whether dirt or a foreign object could have clogged the cooling

fan, and clean the fan itself if necessary.

26–27 POWER SUPPLY TEMP TOO HIGH

The amplifier temperature is excessively high, and so the cooling

fan has been set to the maximum speed and the limiter has been

activated.

Since continuous use may cause malfunction in the power supply unit, stop using

immediately, or lower the output level. Also, check whether dirt or a foreign object

could have clogged the cooling fan, and clean the fan itself if necessary.

33 SPEAKER IMPEDANCE TOO LOW [*] The speaker impedance is excessively low. (*: channel name)

Make sure that the speakers are not damaged and the total impedance is not too

low, and inspect the connection of the speaker cables.

USB:COMPATIBLE DEVICES NOT

FOUND

A USB flash drive has not been installed.

Install an appropriate USB flash drive. Refer to Yamaha Pro Audio global website

(http://www.yamahaproaudio.com/) for tested USB flash drive.

51 USB:NO FILE SYSTEM The file system of the USB flash drive is unreadable. Use a USB flash drive formatted properly to FAT32 or FAT16.

52 USB:FILE NOT FOUND The object file has not been found. Make sure the relevant file is contained in the USB flash drive and try again.

53 USB:ILLEGAL FILE Illegal file. Replace with an appropriate file and try again.

54 USB:INCOMPATIBLE FORMAT Incompatible file format. Replace with an appropriate file and try again.

Reference — Message list

PX10/PX8/PX5/PX3 Reference Manual

55 USB:I/O ERROR Cannot read/write the USB flash drive properly.

Confirm that the USB flash drive you are using works properly with a computer. Use

a tested USB flash drive. Refer to Yamaha Pro Audio global website (http://

www.yamahaproaudio.com/) for tested USB flash drive. Should this also fail, con-

tact your Yamaha dealer.

56 USB:STORAGE FULL! The remaining capacity of the USB flash drive is not sufficient. Make sure the USB flash drive has enough free space.

58 USB:LOAD ERROR

The USB flash drive has been unplugged during access. A failure

has occurred in reading files from the USB flash drive. Data in the

PX amplifier may be corrupted or lost.

Try again. The [USB] indicator flashes when the USB flash drive is being accessed.

Do not unplug the USB flash drive during this time.

65 INCOMPATIBLE DATA LOADED

The recalled preset includes incompatible settings, so the setting

has reverted to the default. This also results when a file stored

from PX5/PX3 in Power Boost mode has been restored.

—

70 POWER TURNED ON The device has been turned on. —

71 POWER TURNED OFF The device has been turned off. —

72 SHORT INTERRUPTION

An instantaneous power failure occurred, causing the device to

shut down and start up again.

Connect to a stable power supply.

73 FIRMWARE UPDATE COMPLETED Completed the update of the firmware. —

74 PANEL UNLOCKED Released the panel lock. —

75 SP PRESET RECALLED[*] Recalled a speaker preset. (*: speaker preset number) —

76 SP PRESET LOADED Loaded a speaker preset from the USB flash drive. —

77 AMP PRESET RECALLED[*] Recalled an amplifier preset. (*: amplifier preset number) —

78 AMP PRESET STORED[*] Stored an amplifier preset. (*: amplifier preset number) —

79 AMP PRESET CLEARED[*] Cleared an amplifier preset. (*: amplifier preset number) —

80 BACKUP DATA LOADED

Loaded setting data from a USB flash drive with “RESTORE

FROM USB” in DEVICE BACKUP screen.

—

90 CONFIG+TUNING DATA INITIALIZED Initialized the configuration and tuning data. —

91 ALL DATA INITIALIZED Initialized all the parameter settings. —

92 FACTORY DATA RESET Initialized all the speaker presets and parameter settings. —

Number Message Symptom Possible solution

Reference — Troubleshooting

PX10/PX8/PX5/PX3 Reference Manual

Troubleshooting

Symptom Possible causes Possible solution

The display automatically turns off if the PX

amplifier has not been operated for a while.

For the protection of the display, the display automatically turns off if the

PX amplifier has not been operated for 20 minutes.

Press any key on the front panel or rotate the main knob to turn on the display

again.

If the Black-out mode is on, the back light of the display automatically

turns off when PX amplifier has not been operated for around 10 sec-

onds.

Press any key on the front panel to turn on the back light of the display. If the

Black-out mode is set to off, the back light does not turn off even if the PX

amplifier is not operated.

[PROTECT] indicator lights and an “OUTPUT

CURRENT OVER” message appears on the dis-

play.

There is a short at the speaker terminal, amplifier terminal or wire, and

circuit protection has been engaged.

Turn the power off and check for a short in the speaker terminal or amplifier,

wire, etc., and turn it on again.

Since the impedance of the connected speaker is excessively low and

the amplifier is overloaded, circuit protection has been engaged.

Check that the speaker has not been damaged and that total impedance is not

excessively low, and review the speaker connection.

[PROTECT] indicator lights and “AMP TEMP

TOO HIGH” message appears on the display.

Because the internal temperature is excessively high, thermal protection

has been engaged to protect the circuit.

Check the amplifier ventilation conditions and take appropriate measures to

improve the airflow around the amplifier. Leave the amplifier off until the internal

temperature goes down, and then turn it on again.

[CLIP/LIMIT] indicator lights.

Because the input signal is excessive or the output exceeds the rated

voltage, the signal is clipped or the limiter has been engaged to protect

the circuit.

Lower the output level of the device connected to the input connector, or lower

the volume of the amplifier.

Power does not turn on.

Power suddenly turned off, and immediately

turned off even when turning on again.

The power supply connected outlet is significantly different from the

rated range.

Check the source voltage.

Because the internal temperature is excessively high, thermal protection

has been engaged to protect the circuit.

Check the amplifier ventilation conditions and take appropriate measures to

improve the airflow around the amplifier. Leave the amplifier off until the internal

temperature goes down, and then turn it on again.

The output level is excessively high. Lower the output level.

The device is broken.

After disconnecting the speakers, turn on the device without inputting any sig-

nal, or lower the volume completely, turn on the device. If the symptoms do not

improve, the device is broken. Contact your Yamaha dealer.

Sound from speakers is distorted. The input level exceeds the setting of the input sensitivity.

Adjust the input sensitivity to match the input level with the CONFIG WIZARD

screen.

The sound is muffled. No high-frequency sound.

The sound is filtered. The filter status can be checked in the HOME

screen.

Change the setting of the filters in the MENU screen (TUNING screen).

When “ROUTING” is set to something other than

“DUAL,” the level of channel B is low.

The volume knob of channel B, with which the output balance to channel

A is adjusted, has been lowered.

Raise the volume knob of channel B.

Reference — Troubleshooting

PX10/PX8/PX5/PX3 Reference Manual

* If any specific problem should persist, contact your Yamaha dealer.

No sound from speakers.

Cables are not connected appropriately. If the meter does not rise even if

raising the volume knob, there may be problems in connectivity at the

input side. If the meter rises, there may problems at the output side.

Connect to input jacks and output terminals appropriately. At the output side,

make sure that terminals outputting signals are connected. Refer to “Usage

examples” (page 4) for connection instructions.

The outputs of the mixer connected to the input jacks are lowered. There

is a possibility that the meter does not rise even if the volume knob is

raised.

Raise the output of the mixer.

Level has been lowered with the volume knob. Adjust the volume knob accordingly.

The mute is on. When the mute is on, “MUTE” appears in the HOME

screen.

Turn off the mute.

The protection circuit has been engaged and the output is muted. When

the protection circuit is engaged, the [PROTECTION] indicator lights.

Identify what is causing the protection circuit to engage and solve it.

The speaker type is Power Boost mode (PX5 and PX3 only).

In Power Boost mode, audio signals are not output from channel B. Cancel

Power Boost mode or reconnect the cables.

The panel controls cannot be operated. The panel lock is turned on.

Turn off the panel lock. Refer to “Panel lock”(page 14) for instructions on turn-

ing off the panel lock.

The parameter settings need to be returned to

their initial values.

—

Return the settings to the initial values. To do this, refer to “Initializing the PX

amplifier” (page 37).

An indicator does not light in a condition in which

it normally should light. The display is blank.

The Black-out mode is on.

To temporarily make the indicators light and the display work, operate the

panel. To make the indicators light and the display work regularly, turn off the

Black-out mode. Refer to “PANEL SETUP” (page 34) in UTILITY screen.

The display is dark.

The “BRIGHTNESS” in PANEL SETUP screen is set to low value. Set the “BRIGHTNESS” to a higher value.

For protection of the display, if there is no operation for one minute, the

display automatically darkens.

To turn on the display again, simply press any key on the front panel or rotate

any knob.

After starting up again, parameters you’ve edited

have returned to the values before editing.

The device was shut down before the current parameters were stored

automatically.

When the device is shut down, wait more than 3 seconds after editing current

parameters.

Reading or writing from/to a USB flash drive

takes a long time.

The USB flash drive contains a number of files. The more files that are

contained, the longer time is required.

Delete files the PX amplifier does not need.

Symptom Possible causes Possible solution

Reference — General specifications

PX10/PX8/PX5/PX3 Reference Manual

General specifications

PX10 PX8 PX5 PX3

Output Power

120 V 60 Hz, 220 V-240 V 50 Hz/60 Hz

1 kHz, non-clip, 20 msec burst,

both channels driven

16Ω 500W × 2 400W × 2 250W × 2 150W × 2

12Ω 660W × 2 530W × 2 330W × 2 200W × 2

8Ω 1000 W × 2 800 W × 2 500 W × 2 300 W × 2

4Ω 1200 W × 2 1050 W × 2 800 W × 2 500 W × 2

2Ω 700 W × 2 600 W × 2 500 W × 2 300 W × 2

1 kHz, non-clip, 20 msec burst

16Ω/Power Boost Mode — — 400W × 1 300W × 1

12Ω/Power Boost Mode — — 530W × 1 400W × 1

8Ω/Power Boost Mode — — 800 W × 1 600 W × 1

4Ω/Power Boost Mode — — 1400 W × 1 1000 W × 1

Output Power

100 V 50 Hz/60 Hz

1 kHz, non-clip, 20 msec burst,

both channels driven

16Ω 500W × 2 400W × 2 250W × 2 150W × 2

12Ω 660W × 2 530W × 2 330W × 2 200W × 2

8Ω 1000 W × 2 800 W × 2 500 W × 2 300 W × 2

4Ω 1200 W × 2 1050 W × 2 800 W × 2 500 W × 2

2Ω 700 W × 2 600 W × 2 500 W × 2 300 W × 2

1 kHz, non-clip, 20 msec burst

16Ω/Power Boost Mode — — 400W × 1 300W × 1

12Ω/Power Boost Mode — — 530W × 1 400W × 1

8Ω/Power Boost Mode — — 800 W × 1 600 W × 1

4Ω/Power Boost Mode — — 1200 W × 1 1000 W × 1

Amplifier Type (Output Circuitry) Class D, balanced output circuit (BTL)

THD+N

1 kHz, 10 W 0.1%

1 kHz, half power 0.3%

Frequency Response 1 W, 8Ω, 20 Hz to 20 kHz ±1.0 dB

Crosstalk Half power, 8Ω, 1 kHz, vol. max., input 150Ω shunt -60 dB

S/N Ratio A-weighted, 8Ω, gain setting = +14 dBu 101 dB 101 dB 100 dB 100 dB

Voltage Gain/Sensitivity

8Ω, volume max.

Gain setting: 32 dB 32.0 dB/+9.3 dBu 32.0 dB/+8.3 dBu 32.0 dB/+6.3 dBu 32.0 dB/+4.1 dBu

Gain setting: 26 dB 26.0 dB/+15.3 dBu 26.0 dB/+14.3 dBu 26.0 dB/+12.3 dBu 26.0 dB/+10.1 dBu

Gain setting: +4 dBu 37.3 dB/+4 dBu 36.3 dB/+4 dBu 34.3 dB/+4 dBu 32.1 dB/+4 dBu

Gain setting: +14 dBu 27.3 dB/+14 dBu 26.3 dB/+14 dBu 24.3 dB/+14 dBu 22.1 dB/+14 dBu

8Ω, volume max.,

Power Boost mode

Gain setting: 32 dB — — 34.0 dB/+6.3 dBu 35.0 dB/+4.1 dBu

Gain setting: 26 dB — — 28.0 dB/+12.3 dBu 29.0 dB/+10.1 dBu

Gain setting: +4 dBu — — 36.3 dB/+4 dBu 35.1 dB/+4 dBu

Gain setting: +14 dBu — — 26.3 dB/+14 dBu 25.1 dB/+14 dBu

Load Protection

POWER switch on/off Output mute

Output voltage protection Over voltage limiter, user configurable by wattage and speaker preset

DC-fault Power supply shutdown (NOT restored automatically)

Reference — General specifications

PX10/PX8/PX5/PX3 Reference Manual

*1 Device operation has been confirmed within ±10% of the rated power supply voltage.

* The contents of this manual apply to the latest specifications as of the publishing date. To obtain the latest manual, access the Yamaha website then download the manual file.

Amplifier Protection

Thermal Output limiter (Restored automatically)  Output mute (Restored automatically)

Over current Output mute (Restored automatically)

Over voltage Output limiter (Restored automatically)

Integrated Power Limit Output limiter (Restored automatically)

Power Supply Protection

Thermal Output limiter (Restored automatically)  Power supply shutdown

Over voltage Power supply shutdown

Over current Power supply shutdown

Cooling 16 step variable speed fan × 2, front to rear airflow

Maximum Input Voltage +24 dBu

Input Impedance 20 kΩ (Balance), 10 kΩ (Unbalance)

Sampling Frequency 48 kHz

A/D, D/A Converters

AD: 24-bit linear, 128 times over sampling

DA: 24-bit linear, 128 times over sampling

Signal Processing

Input summing

D-CONTOUR: FOH/MAIN, MONITOR, OFF

Delay: 0–74msec

HPF/LPF: cutoff frequency 20 Hz–20 kHz with polarity control

Speaker processor: 6 band PEQ + Limiter + Delay

Latency Analog input to speakers 1. 5 m s e c

User Amplifier Preset 8 user amplifier presets

Factory Speaker Preset Speaker presets for Yamaha passive speakers

Connectors

Analog input XLR-3-31 × 2, 1/4" PHONE(TRS) × 2

Speakers Neutrik speakON NL4 × 2, binding post × 2 pairs, 1/4" PHONE(TS) × 2

AC IN AC inlet × 1 with AC cord clamp

USB USB 2.0 Standard-A connector (female) for save/load, speaker preset update, firmware update with USB flash drive

Controls

Front Panel

POWER switch, 31 step volume knob × 2, rotary encoder and switches for GUI control

Operation lock feature (Full lock or Lock except volume and mute)

Display

128 × 64 pixel, mono color with brightness adjustment

Auto display off feature

Indicators

POWER × 1 (green), ALERT × 1 (red), USB × 1 (green), PROTECT × 2 (red), CLIP/LIMIT × 2 (red), SIGNAL × 2 (green)

Auto LED off feature

AC Power Requirement Depending on area of purchase; 100 V 50 Hz/60 Hz, 120 V 60 Hz, 220 V-240 V 50 Hz/60 Hz

Power Consumption

1/8 MAX power, 4Ω, Pink noise at all channels 310 W 280 W 230 W 160 W

Idle, 4Ω 60 W 60 W 55 W 55 W

Operating Temperature 0°C to +40°C

Storage Temperature -20°C to +60°C

Dimensions (W × H × D) 480 × 88 × 388 mm (18.90 × 3.46 × 15.28 inch)

Net Weight 7.4 kg (16.31 lbs) 7.2 kg (15.87 lbs) 6.9 kg (15.21 lbs) 6.9 kg (15.21 lbs)

PX10 PX8 PX5 PX3

Reference — Block diagram

PX10/PX8/PX5/PX3 Reference Manual

Block diagram

CLIP

OUTPUT

METER,

SIGNAL

Volume

Balance

Protection Logic

Speaker Processor

INPUT A

D-Contour

FOH/MAIN

MONITOR

Delay

D-Contour

FOH/MAIN

MONITOR

Delay

Volume

HPF

LPF

Polarity

6-band

PEQ

Speaker

Delay

Level

Limiter

Protection Block

Limiter

Amplifier ClipOutput Voltage

Output Current

Integral Output

Power

Temperature

AC IN

Shutdown

Limit,

Mute

DAC

Mute

FAN x 2

SPEAKERS

Input

Sensitivity/

Gain

+4dBu

+14dBu

26dB

32dB

Input

Router

DUAL

PARALLEL

SINGLE

SUM

Router

Mute

A:POSITIVE

A:NEGATIVE

B:NEGATIVE

DSP

LIMIT PROTECT

OUTPUT

METER,

SIGNAL

INPUT

METER

ADC

CLIP

ADC

CLIP

INPUT

METER

LIMIT

HPF

LPF

Polarity

6-band

PEQ

Speaker

Delay

Level Limiter Limiter

LIMIT LIMIT

B:POSITIVE

AMP

CLIP

AMP

DAC

Mute

Power Supply

INPUT B

Reference — Dimensions

PX10/PX8/PX5/PX3 Reference Manual

Dimensions

430

480

361 (Mounting Surface to Rear End)

388

24.5

2.5

unit: mm

Reference — Current draw and thermal dissipation

PX10/PX8/PX5/PX3 Reference Manual

Test signal: Pink noise (bandwidth limited from 22 Hz to 22 kHz), 1 Btu = 1,055.06 J = 0.252 kcal, (W) × 0.86 = kcal

 PX10

Current draw and thermal dissipation

100 V/50 Hz

Current Draw (A)

@100V

Watt (W) Thermal dissipation

Power consumption

(In)

Power consumption

(Out)

Watts dissipated Btu/h kcal/h

Idle 0.8 57 0 57 195 49

1/8 out

8Ω/ch 2.6 213 125 88 300 76

4Ω/ch 3.1 261 150 111 379 95

1/3 out

8Ω/ch 5.6 472 333 139 474 120

4Ω/ch 7.2 608 400 208 710 179

110 V-120 V/60 Hz

Current Draw (A)

@120V

Watt (W) Thermal dissipation

Power consumption

(In)

Power consumption

(Out)

Watts dissipated Btu/h kcal/h

Idle 0.7 60 0 60 205 52

1/8 out

8Ω/ch 2.2 213 125 88 300 76

4Ω/ch 2.7 263 150 113 386 97

1/3 out

8Ω/ch 4.6 466 333 133 454 114

4Ω/ch 5.9 597 400 197 672 169

220 V-240 V/50 Hz

Current Draw (A)

@230V

Watt (W) Thermal dissipation

Power consumption

(In)

Power consumption

(Out)

Watts dissipated Btu/h kcal/h

Idle 0.5 62 0 62 212 53

1/8 out

8Ω/ch 1.4 219 125 94 321 81

4Ω/ch 1.6 271 150 121 413 104

1/3 out

8Ω/ch 2.7 471 333 138 471 119

4Ω/ch 3.3 602 400 202 689 174

Reference — Current draw and thermal dissipation

PX10/PX8/PX5/PX3 Reference Manual

 PX8

100 V/50 Hz

Current Draw (A)

@100V

Watt (W) Thermal dissipation

Power consumption

(In)

Power consumption

(Out)

Watts dissipated Btu/h kcal/h

Idle 0.8 57 0 57 195 49

1/8 out

8Ω/ch 2.2 178 100 78 266 67

4Ω/ch 2.9 237 131 106 362 91

1/3 out

8Ω/ch 4.6 386 267 119 406 102

4Ω/ch 6.4 543 350 193 659 166

110 V-120 V/60 Hz

Current Draw (A)

@120V

Watt (W) Thermal dissipation

Power consumption

(In)

Power consumption

(Out)

Watts dissipated Btu/h kcal/h

Idle 0.7 60 0 60 205 52

1/8 out

8Ω/ch 1.9 182 100 82 280 71

4Ω/ch 2.5 237 131 106 362 91

1/3 out

8Ω/ch 3.8 385 267 118 403 101

4Ω/ch 5.4 542 350 192 655 165

220 V-240 V/50 Hz

Current Draw (A)

@230V

Watt (W) Thermal dissipation

Power consumption

(In)

Power consumption

(Out)

Watts dissipated Btu/h kcal/h

Idle 0.5 62 0 62 212 53

1/8 out

8Ω/ch 1.2 184 100 84 287 72

4Ω/ch 1.5 242 131 111 379 95

1/3 out

8Ω/ch 2.2 385 267 118 403 101

4Ω/ch 3.0 544 350 194 662 167

Reference — Current draw and thermal dissipation

PX10/PX8/PX5/PX3 Reference Manual

 PX5

100 V/50 Hz

Current Draw (A)

@100V

Watt (W) Thermal dissipation

Power consumption

(In)

Power consumption

(Out)

Watts dissipated Btu/h kcal/h

Idle 0.8 46 0 46 157 40

1/8 out

8Ω/ch 1.9 122 63 59 201 51

4Ω/ch 2.7 189 100 89 304 77

1/3 out

8Ω/ch 3.6 253 167 86 293 74

4Ω/ch 5.6 424 267 157 536 135

110 V-120 V/60 Hz

Current Draw (A)

@120V

Watt (W) Thermal dissipation

Power consumption

(In)

Power consumption

(Out)

Watts dissipated Btu/h kcal/h

Idle 0.8 54 0 54 184 46

1/8 out

8Ω/ch 1.7 130 63 67 229 58

4Ω/ch 2.4 196 100 96 328 83

1/3 out

8Ω/ch 3.1 259 167 92 314 79

4Ω/ch 4.8 428 267 161 549 138

220 V-240 V/50 Hz

Current Draw (A)

@230V

Watt (W) Thermal dissipation

Power consumption

(In)

Power consumption

(Out)

Watts dissipated Btu/h kcal/h

Idle 0.5 57 0 57 195 49

1/8 out

8Ω/ch 1.0 130 63 67 229 58

4Ω/ch 1.4 197 100 97 331 83

1/3 out

8Ω/ch 1.9 259 167 92 314 79

4Ω/ch 2.9 434 267 167 570 144

Reference — Current draw and thermal dissipation

PX10/PX8/PX5/PX3 Reference Manual

 PX3

100 V/50 Hz

Current Draw (A)

@100V

Watt (W) Thermal dissipation

Power consumption

(In)

Power consumption

(Out)

Watts dissipated Btu/h kcal/h

Idle 0.8 46 0 46 157 40

1/8 out

8Ω/ch 1.5 94 38 56 191 48

4Ω/ch 2.0 137 63 74 253 64

1/3 out

8Ω/ch 2.6 174 100 74 253 64

4Ω/ch 3.9 285 167 118 403 101

110 V-120 V/60 Hz

Current Draw (A)

@120V

Watt (W) Thermal dissipation

Power consumption

(In)

Power consumption

(Out)

Watts dissipated Btu/h kcal/h

Idle 0.8 54 0 54 184 46

1/8 out

8Ω/ch 1.3 100 38 62 212 53

4Ω/ch 1.8 140 63 77 263 66

1/3 out

8Ω/ch 2.3 183 100 83 283 71

4Ω/ch 3.4 291 167 124 423 107

220 V-240 V/50 Hz

Current Draw (A)

@230V

Watt (W) Thermal dissipation

Power consumption

(In)

Power consumption

(Out)

Watts dissipated Btu/h kcal/h

Idle 0.5 57 0 57 195 49

1/8 out

8Ω/ch 0.8 101 38 63 215 54

4Ω/ch 1.1 142 63 79 270 68

1/3 out

8Ω/ch 1.4 181 100 81 276 70

4Ω/ch 2.1 293 167 126 430 108

Reference — Index

PX10/PX8/PX5/PX3 Reference Manual

[A] key .............................................................................8

[AC IN] connector ............................................................9

AC plug clamp .................................................................9

Advanced mode ............................................................12

[ALERT] indicator ............................................................8

Alert messages .............................................................14

AMP PRESET screen ...................................................32

amplifier gain ...................................................................7

[B] key .............................................................................8

[ ] (back) key ..............................................................8

Basic mode ...................................................................12

basic operation ..............................................................12

BI-AMP ..........................................................................22

binding post connector ..................................................11

Black-out mode .............................................................34

Block diagram ...............................................................48

CHANNEL COPY ..........................................................30

CHANNEL LINK ............................................................30

CLEAR ..........................................................................32

[CLIP/LIMIT] indicator .....................................................8

Clipping/limiting message .............................................15

CONFIG VIEW icon ......................................................15

CONFIG VIEW screen ..................................................16

CONFIG WIZARD screen (Advanced mode) ................22

CONFIG WIZARD screen (Basic mode) .......................20

CONFIRMATION (Advanced mode) .............................24

CONFIRMATION (Basic mode) ....................................21

Connecting to [SPEAKERS] terminal ............................11

connection, speaker ......................................................11

crossover ......................................................................26

Current draw .................................................................50

Current parameter .........................................................37

D-CONTOUR ................................................................ 25

D-CONTOUR indication ................................................15

DELAY ..........................................................................26

Delay indication ............................................................. 15

DEVICE BACKUP .........................................................36

DEVICE INFORMATION .............................................. 36

Dimensions ................................................................... 49

Display ............................................................................ 8

DUAL ............................................................................23

Dual mode .....................................................................23

EQ (6 Band PEQ) ......................................................... 29

EQ indication ................................................................. 15

Exhaust ports ..................................................................9

Filter indication ..............................................................15

Front panel ...................................................................... 8

FULL (MONO) ...............................................................22

FULL+FULL ..................................................................22

FULL+SUB .................................................................... 22

General specifications ...................................................46

High pass filter .............................................................. 27

HOME SCREEN ........................................................... 35

HOME screen ............................................................... 15

HPF ............................................................................... 27

[ ] icon ....................................................................... 15

IMPORT SP PRESET ................................................... 35

Import speaker preset ................................................... 35

initialization ................................................................... 37

INITIALIZE .................................................................... 36

input configuration .......................................................... 6

[INPUT] connectors ........................................................ 9

Input processor ............................................................... 7

input sensitivity ............................................................... 7

Input sensitivity/amplifier gain ....................................... 24

Intake ports ..................................................................... 8

LEVEL ........................................................................... 29

Level meter ................................................................... 15

LIMITER ........................................................................ 30

LOG .............................................................................. 37

Low pass filter ............................................................... 27

LPF ............................................................................... 27

Main knob ....................................................................... 8

[MENU] key ..................................................................... 8

MENU screen ............................................................... 17

MENU screen operation ............................................... 17

Message list .................................................................. 42

Mute indication .............................................................. 15

Index

Reference — Index

PX10/PX8/PX5/PX3 Reference Manual

operation, MENU screen ...............................................17

operation tree (MENU screen) ......................................18

output combination ..........................................................6

Output level ...................................................................29

PANEL LOCK ...............................................................34

panel lock ......................................................................14

PANEL SETUP .............................................................34

PARALLEL ....................................................................23

Parallel mode ................................................................23

phone jack .......................................................................9

PIN code .......................................................................34

POLARITY ....................................................................28

Polarity indication ..........................................................15

power button ...................................................................8

[POWER] indicator ..........................................................8

PROTECT .....................................................................33

[PROTECT] indicator ......................................................8

rack mounting ...............................................................11

rear panel ........................................................................9

RECALL ........................................................................32

ROUTING .....................................................................23

routing .............................................................................6

SAVE/LOAD ..................................................................31

screen structure ............................................................13

SENS./GAIN .................................................................24

setup .............................................................................10

[SIGNAL] indicator ..........................................................8

SINGLE .........................................................................23

Single mode ..................................................................23

SP DELAY ....................................................................28

SP IMPEDANCE ...........................................................24

SP MODEL (Advanced mode) ...................................... 24

SP MODEL (Basic mode) ............................................. 20

SP SERIES (Advanced mode) ......................................24

SP SERIES (Basic mode) .............................................20

SP TYPE (Advanced mode) ......................................... 22

SP TYPE (Basic mode) .................................................20

speaker connection ....................................................... 11

Speaker impedance ......................................................24

Speaker model (Advanced mode) ................................24

Speaker model (Basic mode) ........................................20

speaker name ...............................................................15

Speaker polarity ............................................................ 28

Speaker processor ..........................................................7

Speaker series (Advanced mode) .................................24

Speaker series (Basic mode) ........................................ 20

speaker type ...................................................................6

Speaker type (Advanced mode) ...................................22

Speaker type (Basic mode) ...........................................20

[SPEAKERS] connection .............................................. 11

[SPEAKERS] terminals ...................................................9

speakON connector ...................................................... 11

STORE ..........................................................................32

SUB (MONO) ................................................................22

SUB+SUB .....................................................................22

SUM ..............................................................................23

Sum mode .....................................................................23

Thermal dissipation ....................................................... 50

Threshold indication ......................................................15

TITLE ............................................................................33

Troubleshooting ............................................................44

TUNING screen ............................................................25

[USB] indicator ................................................................ 8

[USB] terminal ................................................................. 8

User data ...................................................................... 38

UTILITY screen ............................................................. 34

VOL/BAL/GAIN indication ............................................. 15

Volume indication ......................................................... 15

Volume knob ................................................................... 8

WIZARD MODE ............................................................ 22

XLR jack ......................................................................... 9

X-OVER ........................................................................ 26

Y-plugs .......................................................................... 11

Manual Development Group

Published 08/2018 PO-E0

Yamaha Pro Audio global website

https://www.yamaha.com/proaudio/

Yamaha Downloads

https://download.yamaha.com/

Yamaha PX10 Handleiding

Merk: Yamaha

Model: PX10

Type: Handleiding

Deze handleiding is ook geschikt voor

Download PDF

rapport

in andere talen

English: Yamaha PX10 User manual
italiano: Yamaha PX10 Manuale utente
русский: Yamaha PX10 Руководство пользователя
français: Yamaha PX10 Manuel utilisateur
español: Yamaha PX10 Manual de usuario
Deutsch: Yamaha PX10 Benutzerhandbuch
português: Yamaha PX10 Manual do usuário
dansk: Yamaha PX10 Brugermanual
suomi: Yamaha PX10 Ohjekirja
čeština: Yamaha PX10 Uživatelský manuál
svenska: Yamaha PX10 Användarmanual
Türkçe: Yamaha PX10 Kullanım kılavuzu
polski: Yamaha PX10 Instrukcja obsługi
română: Yamaha PX10 Manual de utilizare

Yamaha PX10 Handleiding

Deze handleiding is ook geschikt voor

Yamaha PX10 Handleiding

in andere talen

Gerelateerde artikelen

Andere documenten