Yamaha RX-V2090 Handleiding

Categorie
Cassettespelers
Type
Handleiding
OWNER’S MANUAL
Contents
PROFILE OF THIS UNIT ............................ 6
SPEAKER SETUP FOR THIS UNIT........... 7
CONNECTIONS ......................................... 9
ADJUSTMENT BEFORE OPERATION.... 16
BASIC OPERATIONS .............................. 19
TUNING OPERATIONS ........................... 22
USING THE DIGITAL SOUND FIELD
PROCESSOR (DSP) ................................ 26
SETTING THE SLEEP TIMER ................. 31
REMOTE CONTROL TRANSMITTER ..... 32
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Explanation of Graphical Symbols
The lightning flash with arrowhead
symbol, within an equilateral triangle,
is intended to alert you to the
presence of uninsulated “dangerous
voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an
equilateral triangle is intended to
alert you to the presence of
important operating and
maintenance (servicing) instructions
in the literature accompanying the
appliance.
IMPORTANT!
Please record the serial number of this
unit in the space below.
Model:
Serial No.:
The serial number is located on the rear
of the unit.
Retain this Owner’s Manual in a safe
place for future reference.
WARNING
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE
THIS UNIT TO RAIN OR MOISTURE.
RX-V2090
Natural Sound Stereo Receiver
SAFETY INSTRUCTIONS
1 Read Instructions — All the safety and operating
instructions should be read before the unit is operated.
2 Retain Instructions — The safety and operating
instructions should be retained for future reference.
3 Heed Warnings — All warnings on the unit and in the
operating instructions should be adhered to.
4 Follow Instructions — All operating and other
instructions should be followed.
5 Water and Moisture — The unit should not be used near
water – for example, near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a
swimming pool, etc.
6 Carts and Stands — The unit should be used only with a
cart or stand that is recommended by the manufacturer.
6A An unit and cart combination should be
moved with care. Quick stops,
excessive force, and uneven surfaces
may cause the unit and cart
combination to overturn.
7 Wall or Ceiling Mounting — The unit should be mounted
to a wall or ceiling only as recommended by the
manufacturer.
8 Ventilation — The unit should be situated so that its
location or position does not interfere with its proper
ventilation. For example, the unit should not be situated
on a bed, sofa, rug, or similar surface, that may block
the ventilation openings; or placed in a built-in
installation, such as a bookcase or cabinet that may
impede the flow of air through the ventilation openings.
9 Heat — The unit should be situated away from heat
sources such as radiators, stoves, or other appliances
that produce heat.
10 Power Sources — The unit should be connected to a
power supply only of the type described in the operating
instructions or as marked on the unit.
11 Power-Cord Protection — Power-supply cords should
be routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying
particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the unit.
12 Cleaning — The unit should be cleaned only as
recommended by the manufacturer.
13 Nonuse Periods — The power cord of the unit should be
unplugged from the outlet when left unused for a long
period of time.
14 Object and Liquid Entry — Care should be taken so that
objects do not fall into and liquids are not spilled into the
inside of unit.
15 Damage Requiring Service — The unit should be
serviced by qualified service personnel when:
A.
The power-supply cord or the plug has been damaged; or
B. Objects have fallen, or liquid has been spilled into the
unit; or
C. The unit has been exposed to rain; or
D. The unit does not appear to operate normally or exhibits
a marked change in performance; or
E. The unit has been dropped, or the enclosure damaged.
16 Servicing — The user should not attempt service the
unit beyond those means described in the operating
instructions. All other servicing should be referred to
qualified service personnel.
17 Power Lines — An outdoor antenna should be located
away from power lines.
18
Grounding or Polarization — Precautions should be taken
so that the grounding or polarization is not defeated.
19 Outdoor Antenna Grounding — If an outside antenna is
connected to this unit, be sure the antenna system is
grounded so as to provide some protection against
voltage surges and built-up static charges. Article 810 of
the National Electrical Code, ANSI/NFPA 70, provides
information with regard to proper grounding of the mast
and supporting structure, grounding of the lead-in wire
to an antenna discharge unit, size of grounding
conductors, location of antenna discharge unit,
connection to grounding electrodes, and requirements
for the grounding electrode.
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERIVCE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC – NATIONAL ELECTRICAL CODE
ELECTRIC
SERVICE
EQUIPMENT
GROUND
CLAMP
MAST
ANTENNA
LEAD IN
WIRE
EXAMPLE OF ANTENNA GROUNDING
Note to CATV system installer:
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be
connected to the grounding system of the building, as
close to the point of cable entry as practical.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT
1 To ensure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
2 Install your unit in a cool, dry, clean place – away from
windows, heat sources, and too much vibration, dust,
moisture or cold. Avoid sources of hum (transformers,
motors). To prevent fire or electrical shock, do not
expose to rain and water.
3 Do not operate the unit upside-down. It may overheat,
possibly causing damage.
4 Never open the cabinet. If a foreign object drops into
the set, contact your dealer.
5 Do not use force on switches, knobs or cords. When
moving the set, first turn the unit off. Then gently
disconnect the power plug and the cords connecting to
other equipment. Never pull the cord itself.
6 Do not attempt to clean the unit with chemical solvents;
this might damage the finish. Use a clean, dry cloth.
7 Always set the volume control to “– ” before starting
the audio source play: increase the volume gradually to
an appropriate level after the play is started.
8
To prevent lightning damage, pull out the power cord
and remove the antenna cable during an electrical storm.
9
Be sure to read the “Troubleshooting” section on common
operating errors before concluding that your unit is faulty.
10 Do not connect audio equipment to the AC outlets on
the rear panel if that equipment requires more power
than the outlets are rated to provide.
11 When not planning to use this unit for long periods of
time (ie., vacation, etc.), disconnect the AC power plug
from the wall outlet.
The apparatus is not disconnected from the AC power
source as long as it is connected to the wall outlet, even
if the apparatus itself is turned off.
1. IMPORTANT NOTICE: DO NOT MODIFY THIS
UNIT! This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved
by Yamaha may void your authority, granted by the
FCC, to use the product.
2. IMPORTANT: When connecting this product to
accessories and/or another product use only high
quality shielded cables. Cable/s supplied with this
product MUST be used. Follow all installation
instructions. Failure to follow instructions could void
your FCC authorization to use this product in the USA.
3. NOTE: This product has been tested and found to
comply with the requirements listed in FCC
Regulations, Part 15 for Class “B” digital devices.
Compliance with these requirements provides a
reasonable level of assurance that your use of this
product in a residential environment will not result in
harmful interference with other electronic devices.
This equipment generates/uses radio frequencies and,
if not installed and used according to the instructions
found in the users manual, may cause interference
harmful to the operation of other electronic devices.
FCC INFORMATION
Compliance with FCC regulations does not guarantee
that interference will not occur in all installations. If
this product is found to be the source of interference,
which can be determined by turning the unit “OFF”
and “ON”, please try to eliminate the problem by using
one of the following measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch
(circuit breaker of fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/
reorient the antenna. If the antenna lead-in is 300 ohm
ribbon lead, change the lead-in to coaxial type cable.
If these corrective measures do not produce
satisfactory results, please contact the local retailer
authorized to distribute this type of product. If you can
not locate the appropriate retailer, please contact
Yamaha Electronics Corp., U.S.A. 6600 Orangethorpe
Ave, Buena Park, CA 90620
The above statement apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
We Want You Listening For A Lifetime
YAMAHA and the Electronic Industries Association’s
Consumer Electronics Group want you to get the most out
of your equipment by playing it at a safe level. One that lets
the sound come through loud and clear without annoying
blaring or distortion – and, most importantly, without
affecting your sensitive hearing. Since hearing damage from
loud sounds is often undetectable until it is too
late, YAMAHA and the Electronic Industries
Association’s Consumer Electronics Group
recommend you to avoid prolonged exposure
from excessive volume levels.
4
SUPPLIED ACCESSORIES
After unpacking, check that the following parts are contained.
+
POWER
PLAY
TAPE 1
DIR A DIR B
SKIP
PHONO
CD
TUNER
STOP
VCR 1
VCR 2
STOP PLAY
V–AUX
SLEEP TV VCR AUX
DISC
SKIP
SEARCH
SEARCH
SEARCH
PAUSE/STOP
PAUSE/STOP
DECK
A/B
PRESET
A B C D E
REC/PAUSEREC MUTE TAPE 2 MON
PLAY LD/TV
CHAPTER/CH
+
DISPLAY
MASTER
VOLUME
+
TEST
MUTING
++
+
+
TRANSMIT
/LEARN
DSP
HALL
EFFECT
CHURCH
FRONT LEVEL
CENTER LEVEL
REAR LEVEL
DELAY
TIME
MOVIE THEATER
JAZZ CLUB
STADIUM
PRO LOGIC
SURROUND
SPORTS
ENHANCED
ROCK
THEATER
70mm TV
YPC LEARN
USER
1234
5678
910
ON/OFF
RESET CLEAR
Remote Control Transmitter Indoor FM Antenna
PHONO
SKIP
PLAY
CD
PAUSE/STOPDISC SKIP
+
A B C D E
DIR A
DECK
A
/
B
DIR B
TAPE 1
TAPE 2
STOP
LD/TV
+
PRESET
PLAY
TUNER
PAUSE/STOP
PLAY
STOP
VCR 1
VCR 2
CHAPTER
V–AUX
REMOTE BOURCE
CONTROLLER
Batteries (size AA, LR6, UM-3) User Program Sheets
AM Loop Antenna
Main Remote Room 2 Remote
5
Features
Seven Speaker Configuration
Main: 100 W + 100 W (8) RMS Output Power,
0.015% THD, 20-20,000 Hz
120 W + 120 W (6) RMS Output Power,
0.04% THD, 20-20,000 Hz (USA Model Only)
Center: 100 W (8) RMS Output Power,
0.015% THD, 1 kHz
Front: 35 W + 35 W (8) RMS Output Power,
0.08% THD, 1 kHz
Rear: 35 W + 35 W (8) RMS Output Power,
0.08% THD, 1 kHz
Multi-Room Capability
Multi-Room and Multi-Source with two Remote Control Units
Digital Sound Field Processor
10 Programs including “Cinema DSP” 70mm Movie Theater
5 Channel Discrete Input for Dolby Surround Digital AC-3
Automatic Input Balance Control for Dolby Surround
Test Tone Generator for Easier Speaker Output Balance Adjustment
3 Center Channel Modes (NORMAL/WIDE/PHANTOM)
40-Station Random Access Preset Tuning
Automatic Preset Tuning (FM only)
Preset Station Shifting Capability (Preset Editing)
IF Count Direct PLL Synthesizer Tuning System
Video Signal Input/Output Capability
SLEEP Timer
Remote Control Capability
Program and status messages superimposed on connected video monitor
OPEN/CLOSE THE CONTROL DOOR
To open the door To close the door
When it is not necessary to operate controls inside the control door, close the door.
6
PROFILE OF THIS UNIT
You are the proud owner of a Yamaha stereo receiver –an extremely sophisticated audio component. The Digital
Sound Field Processor (DSP) built into this unit takes full advantage of Yamaha’s undisputed leadership in the
field of digital audio processing to bring you a whole new world of listening experiences. Follow the instructions in
this manual carefully when setting up your system, and this unit will sonically transform your room into a totally
new listening environment –movie theater, concert hall, and so on. In addition, you get incredible realism from
Dolby-encoded video sources using the built-in Dolby Pro Logic Surround Decoder.
Please read this owner’s manual carefully and store it in a safe place for later reference.
this same sound in your own listening room, so you’ll
feel all the sound of a live concert.
Furthermore, our technicians, armed with sophisti-
cated measuring equipment, have even made it
possible to capture the acoustics of a variety of venues
such as an actual concert hall, theater, etc. to allow
you to accurately recreate one of several actual live
performance environments, all in your own home.
Digital Sound Field Processing
What is it that makes live music so good? Today’s
advanced sound reproduction technology lets you get
extremely close to the sound of a live performance,
but chances are you’ll still notice something missing:
the acoustic environment of the live concert hall.
Extensive research into the exact nature of the sonic
reflections that create the ambience of a large hall has
made it possible for Yamaha engineers to bring you
Dolby Pro Logic Surround
The Dolby Pro Logic Surround Decoder program lets
you experience the dramatic realism and impact of
Dolby Surround movie theater sound in your own
home. Dolby Pro Logic gets its name from its profes-
sional-grade steering logic circuitry, which provides
greater effective front and rear channel separation for
a much higher degree of realism than the “passive”
Dolby Surround circuits found in less sophisticated
home audio/video equipment. Dolby Pro Logic
Surround provides a true center channel, so that there
are four independent channels, unlike passive Dolby
Surround which has in effect only three channels: left,
right, and rear. This center channel allows listeners
seated in even less-than-ideal positions to hear the
dialog originating from action on the screen while
getting a stereo effect as well.
This Dolby Pro Logic Surround Decoder employs a
digital signal processing system. This system in-
creases sound stability at each channel and minimizes
crosstalk between channels compared to conventional
analog Dolby signal processing.
In addition, this unit features a built-in automatic
input balance control. This circuit always presents
you the best surround conditions without performing
manual adjustments.
Dolby Pro Logic Surround + DSP
You can also enjoy Dolby Pro Logic with two modes
of Digital Sound field processing. These combinations
expand the surround effect. One is the “EN-
HANCED” Dolby Pro Logic Surround which recre-
ates the surround effect of the 35 mm film movie
theater. The other is the sound field program ”70 mm
MOVIE THEATER”. Which recreates the listening
experience of a 70 mm film theater.
Directional Enhancement Circuit + DSP
The newly featured directional enhancement circuit
expands and focuses the digital sound field by
emphasizing position of sound.
This effect puts you in the midst of the action, while
centering and focusing your attention to the screen.
This circuit is available on the sound field program
“TV THEATER” and “SPORTS”.
CINEMA DSP
The YAMAHA “CINEMA DSP” logo indicates
these programs are created by the combination of
Dolby Pro Logic and YAMAHA DSP technology.
7
SPEAKER SETUP FOR THIS UNIT
SPEAKERS TO BE USED
This unit is designed to provide the best sound-field quality with a seven speaker configuration. The speakers to be
used with this unit will be main speakers, front speakers, rear speakers, and a center speaker.
The main speakers are used for the main source sound. These are usually a much larger, high-quality loudspeaker
than you will use for the surround sound effects. The center speaker is used for the center sound (dialog, etc.)
encoded with the Dolby Surround. And the front and rear speakers are used for special effects that enhance the
surround sound. The front, rear, and center speakers do not need to be equal to the main speakers. However, all
the speakers should have high enough power handling to accept the maximum output of this unit.
SPEAKER CONFIGURATION
Seven-Speaker Configuration
This configuration is the most effective and recommended
one. In this configuration, the front speakers and the center
speaker are necessary along with the rear speakers. If the
digital sound field program DOLBY PRO LOGIC, DOLBY
PRO LOGIC ENHANCED, 70 mm MOVIE THEATER, TV
THEATER, or SPORTS is selected, conversations will be
output from the center speaker and the ambience will be
excellent.
The FRONT MIX switch on the rear panel should be set to
the “7 ch” setting. (For details, refer to page 17.)
Set the center channel mode to the “NORMAL” or
“WIDE” position. (For details, refer to page 17.)
Five-Speaker Configuration
When you only have five speakers, this configuration can be
very effective. In this configuration, the center speaker is
used for dialog when you select the digital sound field
program DOLBY PRO LOGIC, DOLBY PRO LOGIC EN-
HANCED, 70 mm MOVIE THEATER, TV THEATER, or
SPORTS. The front speakers are not used. The main speakers
handle the front channel effects.
The FRONT MIX switch should be set to the “5 ch”
setting. (For details, refer to page 17.)
Set the center channel mode to the “NORMAL” or
“WIDE” position. (For details, refer to page 17.)
Four-Speaker Configuration
The center speaker is not used in this configuration. If the
digital sound field program DOLBY PRO LOGIC or DOLBY
PRO LOGIC ENHANCED is selected, the center sound
along with the front effects are output from the left and the
right main speakers. However, the sound effect of other
programs can be the same as that of the other configurations.
Be sure to set the center channel mode to the “PHAN-
TOM” position. (For details, refer to page 17.)
Main L Center Main R
Dialogue
Surround sound
Dialogue
Surround sound
Rear L
Rear R
Main L Center Main R
Dialogue
Surround sound
Dialogue
Surround sound
Rear L
Rear R
Front RFront L
Main L Main R
Dialogue
Surround sound
Dialogue
Surround sound
Rear L Rear R
8
SPEAKER PLACEMENT
The recommended speaker configuration, the seven-speaker configuration, will require three speaker pairs: main
speakers, front speakers, and rear speakers, plus a center speaker. When you place these speakers, refer to the
following:
Main: In normal position. (The position of a standard
stereo speaker setup)
Front: Placed much further apart than the Main speakers,
facing slightly inwards. Nearly six feet (approx. 1.8
m) up from the floor.
Center: Precisely between the main speakers. (To avoid
interference with TV sets, use a magnetically
shielded speaker.) When two center speakers are
used, place these to the right and left of your TV
set or video monitor.
Rear: Behind your listening position, facing slightly
inward. Nearly six feet (approx. 1.8 m) up from the
floor.
Rear L
Main R
Center
Main L
Rear R
Front L
Front R
9
CONNECTIONS
CAUTION
Before attempting to make any connections to or from this unit, be sure to first switch OFF the power to this
unit and to any other components to which connections are being made.
CONNECTIONS WITH OTHER COMPONENTS
When making connections between this unit and other components, be sure all connections are made correctly,
that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Also, refer to the owner’s manual for each
component to be connected to this unit.
10dB
0dB
-
OFF
ON
PHONO
CD
TAPE 1
LD/TV
VCR 1
VCR 2
TAPE
PB
REC
OUT
IN
OUT
IN
OUT
VIDEO SIGNAL
AUDIO SIGNAL
MONITOR
OUT
S VIDEO
IN OUT
AUDIO SIGNAL
TAPE 2
TAPE
PB
REC
OUT
LD/TV
VCR 1
VCR 2
IN
OUT
IN
OUT
VIDEO
5ch
7ch
FRONT
MIX
AM
ANT
GND
FM
ANT
GND
75
UNBAL.
MAIN
IN
MAIN CH
MAIN
LEVEL
PRE
OUT
AUDIO
PRE OUT
VIDEO
OUT
LD/TV
CENTER
LD/TV
SURROUND
5CH
DISCRT
INPUT
LD/TV
MAIN
REMOTE CONTROLROOM 2 OUT
Monitor TV
Tape deck 1
Turntable
Video cassette recorder 1
Video cassette recorder 2
Compact disc player
GND
VIDEO IN
Tape deck 2
LaserDisc-Spieler
VIDEO IN
AUDIO IN
VIDEO OUT
AUDIO OUT
VIDEO OUT
AUDIO OUT
OUTPUT
AUDIO OUT
VIDEO OUT
VIDEO IN
AUDIO IN
LINE IN
LINE OUT
LINE IN
LINE OUT
10
CONNECTING SPEAKERS
Connect the respective speakers to this unit as shown below:
A
B
CC
C
+
D
C
A OR B: 5
MIN. /SPEAKER
A
+
B: l2
MIN. /SPEAKER
8
MIN. /SPEAKER
OUTPUT
FRONT
OUT
REAR
OUT
CENTER
OUT
LOW
PASS
fo:200Hz
8
MIN. /SPEAKER
SPEAKERS
FRONT REAR
CENTER
C: 8
MIN. /SPEAKER
C
+
D: 4
MIN. /SPEAKER
DD
Right Left
Main speakers A
Front speakers
Rear speakers
Right Left
Right Left
Right Left
Center speaker(s)
Main speakers B
Note on main speaker connection:
One or two speaker systems can be connected to this
unit. If you connect only one speaker system, connect
it to either the SPEAKERS A or B terminals.
Note on center speaker connection:
One or two center speakers can be connected to this
unit. If you cannot place the center speaker on or
under the TV, it is recommended to use two center
speakers and place them on both sides of the TV to
orient the center sound at the center position.
When connecting two center speakers, be sure to
press the CENTER speaker switch into the “C+D
position ( ) . When you use a single center speaker,
set the switch to the “C” position( ) .
How to Connect:
Connect the SPEAKERS terminals to your speakers
with wire of the proper gauge, cut as short as pos-
sible. If the connections are faulty, no sound will be
heard from the speakers. Make sure that the polarity
of the speaker wires is correct, that is, + and – mark-
ings are observed. If these wires are reversed, the
sound will be unnatural and will lack bass.
CAUTION
Do not let the bare speaker wires touch each other
and do not let them touch the metal parts of this unit.
This could damage this unit and/or the speakers.
Note:
Use speakers with the specified impedance shown on
the rear of this unit.
For connecting to the SPEAKER terminals
Red: positive (+)
Black: negative (–)
1 Unscrew the knob.
2 Insert the bare wire. [Remove
approx. 5mm (1/4") insulation
from the speaker wires.]
3 Tighten the knob and secure
the wire.
Banana Plug connections are also possible. Simply
insert the Banana Plug connector into the correspond-
ing terminal. (Not available on Singapore model.)
Note:
Use only single type banana plug cable.
1
2
3
11
ABOUT THE ACCESSORY TERMINALS
OUTPUT
FRONT
OUT
REAR
OUT
CENTER
OUT
LOW
PASS
fo:200Hz
3
4
2
1
1LOW PASS terminal
This terminal is for output to a monaural amplifier
driving a subwoofer. Frequencies above 200␣ Hz are
filtered out so that only the bass range remains.
The output signal is from the main and center
channels.
You may wish to add a subwoofer to reinforce the
bass frequencies.
Connect the LOW PASS terminal to the INPUT
terminal of the subwoofer amplifier, and connect
the speaker terminals of the subwoofer amplifier to
the subwoofer.
With some subwoofers, including the Yamaha
Active Servo Processing Subwoofer System, the
amplifier and subwoofer are in the same unit.
2CENTER OUTPUT terminal
This terminal is for center channel line output.
There is no connection to this terminal when you
use the built-in amplifier.
However, if you drive a center speaker with an
external power amplifier, connect the input
terminal of the external amplifier to this terminal.
3FRONT OUTPUT terminals
These terminals are for front channel line output.
There is no connection to these terminals when
you use the built-in amplifier.
However, if you drive front speakers with an
external stereo power amplifier, connect the input
terminals of the external amplifier (MAIN IN or
AUX terminals of a power amplifier or an inte-
grated amplifier) to these terminals.
4REAR OUTPUT terminals
These terminals are for rear channel line output.
There is no connection to these terminals when
you use the built-in amplifier.
However, if you drive rear speakers with an
external stereo power amplifier, connect the input
terminals of the external amplifier (MAIN IN or
AUX terminals of a power amplifier or an inte-
grated amplifier) to these terminals.
GND terminal (For turntable use)
Connecting the ground wire of the turn-
table to this terminal will normally mini-
mize hum. In some cases, better results
may be obtained with the ground wire
disconnected.
AC OUTLETS
2 SWITCHED OUTLETS and 1
UNSWITCHED OUTLET (USA,
Canada, and General models)
1 SWITCHED OUTLET (Austra-
lia model)
2 SWITCHED OUTLETS
(Singapore model)
Use these to connect the power cords from your
components to this unit.
The power to the SWITCHED outlets is controlled by
this unit’s POWER switch or the provided remote
control transmitter’s POWER key. These outlets will
(USA model)
SWITCHED UNSWITCHED
120V 60Hz
120W MAX. TOTAL
120V 60Hz
200W MAX.
GND
supply power to any connected component whenever
this unit is turned on.
The maximum power (total power consumption of
components) that can be connected to the SWITCHED
AC OUTLET(S) is 120 watts.
The power to the UNSWITCHED outlets cannot be
controlled by this unit’s POWER switch or the
provided remote control transmitter’s POWER key.
(USA, Canada, and General models only).
The maximum power (power consumption of compo-
nent) that can be connected to the UNSWITCHED AC
OUTLET is 200 watts (USA model), 180 watts
(Canada model) and 200 watts (General model).
12
10dB
0dB
-
OFF
ON
MONITOR
OUT
IN OUT
TAPE 2
REC
OUT
5ch
7ch
FRONT
MIX
MAIN
IN
MAIN CH
MAIN
LEVEL
PRE
OUT
AUDIO
PRE OUT
VIDEO
OUT
LD/TV
CENTER
LD/TV
SURROUND
5CH
DISCRT
INPUT
LD/TV
MAIN
REMOTE CONTROLROOM 2 OUT
6
5
A
9
8
7
0
5MAIN␣ CH — MAIN␣ IN terminals
These terminals are for line input to the built-in
main channel amplifier. Leave the jumper bars
connected to the PRE␣ OUT terminals when you use
the built-in amplifier.
However, if you drive main speakers with an
external stereo power amplifier, remove the
jumper bars.
6MAIN␣ CH — PRE␣ OUT terminals
These terminals are for main channel line output.
Leave the jumper bars connected to the MAIN␣ IN
terminals when you use the built-in amplifier.
However, if you drive main speakers with an
external stereo power amplifier, remove the
jumper bars and connect the input terminals of the
external amplifier (MAIN IN or AUX terminals of
a power amplifier or an integrated amplifier) to
these terminals.
7MAIN LEVEL switch
Normally set to “0␣ dB”. If desired, you can de-
crease the output level at the MAIN SPEAKERS
terminals by 10␣ dB by setting this switch to
“–10␣ dB”.
8ROOM 2 OUT — AUDIO PRE OUT, VIDEO
OUT terminals
These terminals output audio and video signals to
the equipment in the second room. The signal
source is selected using the Room 2 Remote
transmitter. Refer to “Connecting to Room 2
Equipment” on page 14.
9REMOTE CONTROL — IN, OUT terminals
IN This terminal receives the commands from
the Room 2 Remote transmitter.
OUT This terminal outputs the commands at the
IN terminal from Room 2 Remote transmit-
ter. Refer to “Connecting to Room 2 Equip-
ment” on page 14.
0FRONT MIX switch
This switch should be set to match the number of
speakers in your system. For seven speaker
configurations, set it to “7 ch”. For five speaker
configurations, set it to “5 ch”.
A5CH DISCRT INPUT terminals
These terminals are used with a Dolby Surround
AC-3 decoder. Connect the main audio output of
the decoder to the LD/TV MAIN input terminals,
the center channel audio output to the LD/TV
CENTER input terminal, and the surround audio
output to the LD/TV SURROUND input termi-
nals.
Note:
5CH DISCRT INPUT terminals can only be used with an
AC-3 decoder.
When you use a Dolby Surround AC-3 decoder, the LFE
(Low Frequency Effect channel) signal coming from the
AC-3 decoder to this unit must be mixed with the main
output signal. Refer to your AC-3 decoder’s operating
manual for information about mixing these signals mode.
13
CONNECTING S␣ VIDEO TERMINALS
If your video cassette recorder, video disc player, monitor, etc., is equipped with “S” (high-resolution) video
terminals, connect them to this unit’s S␣ VIDEO terminals. Otherwise, use the composite video terminals of the unit.
Note:
If video signals are sent to both the S␣ VIDEO input and composite input terminals, the input signals will be sent to the
respective S␣ VIDEO output and composite output terminals independently.
VIDEO SIGNAL
MONITOR
OUT
S VIDEO
LD/TV
VCR 1
VCR 2
IN
OUT
IN
OUT
VIDEO
Video Cassette recorder 2
Video Cassette recorder 1
LD player
VIDEO
OUT
S VIDEO
OUT
Monitor TV
VIDEO
IN
S VIDEO
IN
S VIDEO OUT
VIDEO OUT
S VIDEO IN
VIDEO IN
S VIDEO OUT
VIDEO OUT
S VIDEO IN
VIDEO IN
ON SCREEN DISPLAY
If you connect a video cassette recorder, video disc player, monitor, etc., to this unit, you can display DSP
program names and information about the other settings and adjustments on the video monitor screen which is
connected to MONITOR OUT terminal (cannot display on ROOM 2 moinitor). This information is superimposed
over the video image.
If there is no program material on the monitor, the information will be displayed over a monochromatic back-
ground.
Notes:
If you use a video monitor that is connected to both the S␣ VIDEO and composite terminals, the screen display informa-
tion is only output from the S␣ VIDEO terminals.
When no video signal is input to any of the S␣ VIDEO or composite video input terminals, the screen display information
is output from the S␣ VIDEO and composite MONITOR OUT terminals with a monochromatic background.
CONNECTING TO VIDEO AUX TERMINALS (FRONT PANEL)
These terminals are used to connect any video input source such as a camcorder to this unit.
AUDIO OUT
AUDIO OUT
VIDEO OUT
L
R
VIDEO
Camcorder
S-VIDEO
S VIDEO OUT
VIDEO AUX
8 VIDEO VIDEO L AUDIO R
8 VIDEO
14
CONNECTING TO ROOM 2 EQUIPMENT
With the Room 2 Remote transmitter you can select a different sound and video source for a second room.
To use the multi-room functions of this unit you need the following additional,optional products:
An infrared signal receiver for the second room. (WCX-10)
Master Zone Controller (MCX-10)
An infrared emitter in the main room. (IRX-10/20)
This emitter transmits the infrared signals from the Room 2 Remote transmitter in the second room to the other
components in the main rooms (for example, the remote for your laserdisc player).
An amplifier and speakers for the second room.
A video monitor for the second room.
Note
Since there are so many ways to connect and use your RX-V2090 in a multi-room installation, we recommend that
you consult with a custom installation specialist for the Room 2 connections which will best meet your require-
ments.
Sample Room 2 connections:
Main Room
Second Room
Infrared emitter
(IRX-10/20)
RX-V2090
Infrared signal
receiver (WCX-10)
Amplifier
Room 2
Remote
Master Zone
Controller MCX-10
Cassette deck, etc
*
Video monitor
REMOTE CONTROL IN
ROOM 2 VIDEO OUT
ROOM2 AUDIO PREOUT
MCX-10
*
Some Yamaha models are able to connect directly to the RX-V2090 via the REMOTE OUT terminals. If you own
these products, the use of an infrared emitter may not be necessary.
CAUTION
In some cases, adjustments made using the Room 2 Remote transmitter may not be evident on this unit.
For example, if both the main room and second room are set to the tuner, it is possible for the person in the
second room to change the station. This may be a problem, especially when you are taping a source without
directly monitoring it.
Using the Remote Transmitters
If you use the Room 2 Remote transmitter (the transmitter for the second room) in the main room, the input
selector keys of this remote affect the settings in the second room, not the main room. The other keys on the
transmitter work the same in both the main room and the second room.
If you use the Main Remote transmitter (the transmitter for the main room) in the second room, the keys that also
appear on the Room 2 Remote transmitter work except the input selector keys.
The indicator information:
1 Lights up momentarily when the Room 2 Remote transmitter is used in
the main room.
2 Lights up momentarily when the Room 2 Remote transmitter is used in
the second room.
ROOM 2
ROOM 2
CONTROL
ROOM 2
1
2
15
ANTENNA CONNECTIONS
Each antenna should be connected to the designated terminals correctly, referring to the following diagram.
Both AM and FM indoor antennas are included with this unit. In general, these antennas will probably provide
sufficient signal strength. Nevertheless, a properly installed outdoor antenna will give clearer reception than an
indoor one. If you experience poor reception quality, an outdoor antenna may result in improvement.
10dB
0dB
-
PHONO
CD
TAPE 1
TAPE
PB
REC
OUT
AUDIO SIGNAL AUDIO
TAPE 2
TAPE
PB
REC
OUT
AM
ANT
GND
FM
ANT
GND
75
UNBAL.
MAIN
IN
MAIN CH
MAIN
LEVEL
PRE
OUT
5CH
DISCRT
INPUT
AM loop
antenna
(included)
Indoor FM
antenna
(included)
Ground
Outdoor AM antenna
Outdoor FM antenna
75-ohm/300-ohm
antenna adapter
75-ohm
coaxial cable
300-ohm
feeder
Connecting the AM loop antenna
12 3
The AM loop antenna should be placed apart from the main unit. The antenna may be hung on a wall.
The AM loop antenna should be kept connected, even if an outdoor AM antenna is connected to this unit.
GND terminal
For maximum safety and minimum interference,
connect the GND terminal to a good earth ground.
A good earth ground is a metal stake driven into
moist earth.
Notes:
When connecting the indoor FM
antenna, insert its connector into the
FM ANT terminal firmly.
If you need an outdoor FM antenna to
improve FM reception quality, either
300-ohm feeder or coaxial cable may be
used. In locations troubled by electrical
interference, coaxial cable is preferable.
Orient so that the best
reception is obtained.
16
ADJUSTMENT BEFORE OPERATION
SPEAKER BALANCE ADJUSTMENT
This procedure lets you adjust the sound output level balance between the main, front, center, and rear speakers
using the built-in test tone generator. With this adjustment, the sound output level heard at the listening position
will be the same from each speaker. This is important for the best performance of the digital sound field processor.
The adjustment of each speaker output level should be done at your listening position with the remote control
transmitter. Otherwise, the result may not be satisfactory.
+
POWER
PLAY
TAPE 1
DIR A DIR B
SKIP
PHONO
CD
TUNER
STOP PLAY
SLEEP TV VCR AUX
DISC
SKIP
SEARCH
SEARCH
PAUSE/STOP
DECK
A/B
PRESET
REC/PAUSEREC MUTE TAPE 2 MON
TRANSMIT
/LEARN
YPC LEARN
USER
6
5
1
34
A B C D E
2
* If you have a video monitor connected to this unit, you should use it to display the on screen information. The
easy-to-read information will help you to perform this adjustment.
Note:
Before adjustment, make sure that the mute circuit is not engaged. While mute is engaged, no sound will be heard and an
indicator on the master VOLUME control flashes. See page 21 for details.
1 Set to the “
” position.
Set the remote YPC-USER-LEARN switch to the “YPC”
position.
4
For detailed information about the remote control transmitter,
refer to “REMOTE CONTROL TRANSMITTER” on page 32.
2 Set to the “0” position.
BASS TREBLE
55
4
3
2
l
0
l
2
3
4
55
4
3
2
l
0
l
2
3
4
YPC LEARN
USER
VOLUME
l6
l8
20
24
28
34
40
50
60
70
l4
l2
l0
8
6
4
3
2
l
0
–dB
5
POWER
Press the POWER
switch to turn on the
power.
6 Select the main speakers to be used.
• If you use two main speaker systems, press both the A and
B switches.
SPEAKERS
AB
3
BALANCE
55
4
3
2
l
0
l
2
3
4
LR
Set to the “0” position.
17
7
STOP
VCR 1
VCR 2
V–AUX
CHAPTER/CH
+
DISPLAY
MASTER
VOLUME
+
TEST
MUTING
++
+
+
DSP
HALL
EFFECT
CHURCH
FRONT LEVEL
CENTER LEVEL
REAR LEVEL
DELAY
TIME
MOVIE THEATER
JAZZ CLUB
STADIUM
PRO LOGIC
SURROUND
SPORTS
ENHANCED
ROCK
THEATER
70mm TV
1234
5678
910
ON/OFF
RESET CLEAR
8
9
7
8
Select the center channel output mode according to your
speaker configuration.
(Refer to “SPEAKER CONFIGURATION” on page 7.)
CENTER
MODE
Turn up the volume using the remote control transmitter.
You will hear a test tone (like pink noise) from the left
main speaker, then the center speaker, then the right
main speaker, and then the rear speakers, for about two
seconds each. The display changes as shown below.
There are two types of tests: Dolby test and DSP test.
• DSP test:
NORMAL
WIDE
PHANTOM
TEST
• Dolby test:
Note:
When the FRONT MIX switch is set to “5ch” (5 channel
mode) the DSP test mode is not available.
* The test tone from the left rear speaker and the right rear
speaker will be heard at the same time.
To adjust the BALANCE, CENTER LEVEL and the
REAR LEVEL, go to steps 10~12.
Press the TEST button to run
the Dolby test.
9
Press the TEST button again to run the DSP test.
*
The test tone from the left main speaker and the right
main speaker, the left front and the right front speaker
will be heard at the same time.
To adjust the FRONT LEVEL, go to step 13.
If your video monitor is on, the state of the test tone
output is also shown by an image of an audio
listening room on the screen.
In step 7, when you select the center mode, note the
following.
Seven and five speaker configuration
NORMAL: Select this mode when you use a
center speaker that is smaller than the
main speakers. In this mode, the bass
tone will be output from the front
main speakers.
WIDE: Select this mode when your center
speakers are approximately the same
size as the main speakers.
Note:
For seven speaker configurations, the FRONT MIX switch
on the rear panel should be set to the “7 ch” setting. For
five speaker configurations, the FRONT MIX switch
should be set to the “5 ch” setting.
Six and Four speaker configuration
PHANTOM: Select this mode when you do not
have a center speaker. The center
channel sound will be output from
the left and right main speakers.
18
Notes:
Once you have completed these adjustments, you can
adjust whole sound level on your audio system by using
the VOLUME control (or the MASTER VOLUME keys
on the remote control transmitter).
If you use external power amplifiers, their volume
controls may also need to be adjusted to achieve the
proper balance.
If there is insufficient sound output from the center
and rear speakers, you may decrease the main
speaker output level by setting the MAIN LEVEL
switch on the rear panel to “–10 dB”.
Notes:
If the center channel mode is in the “PHANTOM”
position, the sound output level of the center speaker
cannot be adjusted. This is because in this mode, the
center sound is automatically output from the left and
right front speakers.
When the FRONT MIX switch is set to 5ch, front level
adjustment cannot be executed from the front panel or
from the REMOTE CONTROL TRANSMITTER.
You cannot adjust the front level when the LD/TV
switch is set to 5CH DISCRT mode.
If you press the LEVEL +/– switch without previously
pressing the FRONT, CENTER, or REAR switch, the
last channel selected will be changed.
10
12
13
Adjust the BALANCE control so that the test tone sound
output level of the left front speaker and the right front
speaker are the same.
Adjust the test tone sound output level of the front
speakers to be at the same level as that of the main
speakers with the FRONT LEVEL keys. (DSP test)
Adjust the sound output level of the rear speakers to be
at the same level as that of the main speakers with the
REAR LEVEL keys. (Dolby test)
14
Cancel the test tone.
BALANCE
55
4
3
2
l
0
l
2
3
4
LR
TEST
LEVEL
FRONT
11
Adjust the test tone sound output level of the center
speaker to be at the same level as that of the main
speakers with the CENTER LEVEL keys. (Dolby test)
CENTER
LEVEL
REAR
LEVEL
PRO LOGIC
The previous mode is selected.
STOP
VCR 1
VCR 2
V–AUX
CHAPTER/CH
+
DISPLAY
MASTER
VOLUME
+
TEST
MUTING
++
+
+
DSP
HALL
EFFECT
CHURCH
FRONT LEVEL
CENTER LEVEL
REAR LEVEL
DELAY
TIME
MOVIE THEATER
JAZZ CLUB
STADIUM
PRO LOGIC
SURROUND
SPORTS
ENHANCED
ROCK
THEATER
70mm TV
1234
5678
910
ON/OFF
RESET CLEAR
14
10
11
13
12
13
12
11
19
BASIC OPERATIONS
4
1,6
2 3
To play a source
POWER
1 Set to the “
” position.
2
Select the main speakers to be used.
• The name of the selected input source will appear on the
display.
3
5
Adjust to the desired output level.
6
VOLUME
l6
l8
20
24
28
34
40
50
60
70
l4
l2
l0
8
6
4
3
2
l
0
–dB
Select the desired input source by using the input selector
buttons. (For video sources, turn the video monitor ON.)
VIDEO AUX
VCR 2 VCR 1
LD/TV
TAPE 2
MONITOR
TUNER CD PHONOTAPE 1
4
SPEAKERS
AB
• If you use two main speaker systems, press both the A and
B switches.
Play the source. (For detailed information on the tuning
operation, refer to page 22.)
VOLUME
l6
l8
20
24
28
34
40
50
60
70
l4
l2
l0
8
6
4
3
2
l
0
–dB
Press the POWER switch
to turn on the power.
If desired, adjust the BASS, TREBLE, BALANCE
controls, etc. (refer to page 21) and use the digital
sound field processor. (Refer to page 26.)
Notes on using the input selector buttons
Note that pressing on each input selector button selects
the source which is connected to the corresponding input
terminals on the rear panel.
To select the source connected to the VIDEO AUX
terminals on the front panel, press VIDEO AUX.
The selection of TAPE 2 MONITOR cannot be canceled
by pressing another input selector button. To cancel it,
press TAPE 2 MONITOR again.
When you select a button other than TAPE 2 MONI-
TOR, make sure that TAPE 2 MONITOR is not
accidently selected as well.
If you select the input selector button for a video source
without canceling the selection of TAPE 2 MONITOR,
the playback result will be the video image from the video
source and the sound from the audio tape.
Once you play a video source, its video image will not be
interrupted even if the input selector button for an audio
source is selected.
For the LD/TV input selector button, refer to page 28.
To turn off the power
Press the POWER switch again.
20
To record a source to tape (or dub from tape to tape)
Notes:
When the REC OUT selector is set to “SOURCE”, the
source selected by the input selector buttons is output
through the TAPE 1-REC OUT, the TAPE 2-REC
OUT , the VCR 1-OUT, and the VCR 2-OUT
terminals.
When the REC OUT selector is set to something other
than “SOURCE” and you press an input selector
button other than the one you pressed in step 2, the
recording source will not be changed and you can enjoy
another source while recording.
To record from tape deck 2, set the REC OUT selector to
SOURCE, and press the TAPE 2/MONITOR input
selector.
If the tape deck connected to the TAPE 2 REC OUT
terminal has 3-head monitoring capability, you can
monitor the signal just recorded on the tape by pressing
the TAPE 2/MONITOR switch.
DSP, VOLUME, BASS, TREBLE and BALANCE
control settings have no effect on the material being
recorded.
Signals connected to the 5CH DISCRT INPUT are not
output to the tape decks or video recorders.
To record the signals from an LD player, you must
connect the player to the LD/TV terminals.
It is possible for someone in the second room to
use the Room 2 Remote transmitter to change the
source you selected for recording. For example, if
you are recording a program from the tuner and
the person in the second room changes the
station. If you are listening to another source, you
may not discover this error until you playback the
recording.
1
2
1 Select the source to be recorded.
2
3
Play the source and press the corresponding input
selector, then turn the VOLUME control up to confirm
the input source. (For detailed information on the tuning
operations, refer to page 22.)
REC OUT
LD/TV
VCR 1
TAPE 1
TUNER
CD
PHONO
VIDEO AUX
VCR 2
SOURCE
Set the tape deck or VCR to the recording mode.
VOLUME
l6
l8
20
24
28
34
40
50
60
70
l4
l2
l0
8
6
4
3
2
l
0
–dB
4
To monitor a source selected by the REC OUT selector,
press the corresponding input selector button.
VIDEO AUX
VCR 2 VCR 1
LD/TV
TAPE 2
MONITOR
TUNER CD PHONO
TAPE 1
21
Selecting the SPEAKERS system
Because one or two speaker systems (as main speak-
ers) can be connected to this unit, the SPEAKERS
switches allow you to select speaker system A or B, or
both at once.
SPEAKERS
AB
Adjusting the BALANCE control
Adjust the balance of the output volume to the left
and right speakers to compensate for sound imbal-
ance caused by speaker location or listening room
conditions.
BALANCE
55
4
3
2
l
0
l
2
3
4
LR
Note:
This control is effective only for the sound the main
speakers.
Adjusting the BASS and TREBLE controls
BASS
Turn this clockwise to increase (or counter-clockwise
to decrease) the low frequency response.
TREBLE
Turn this clockwise to increase (or counter-clockwise
to decrease) the high frequency response.
BASS TREBLE
55
4
3
2
l
0
l
2
3
4
55
4
3
2
l
0
l
2
3
4
Note:
These controls are effective only for the sound from the
main speakers.
Using the TONE BYPASS switch
Press this switch to revert instantly to the flat states of
the BASS and TREBLE controls without changing the
setting of these controls.
ON
OFF
TONE
BYPASS
Using the BASS EXTENSION switch
You can boost bass frequency response by setting this
switch to the “ON” position. This switch is effective
only on the sound from the main speakers.
ON
OFF
BASS
EXTENSION
MUTING Key (Main Room remote transmitter)
Press this key to mute the master volume. While mute
is engaged, an indicator on the master VOLUME
control flashes. Press again to un-mute the master
volume.
ON/OFF
+
EFFECT
V–AUX
MASTER
VOLUME
+
TEST
+
+
+
DSP
HALLCHURCH
FRONT LEVEL
CENTER LEVEL
REAR LEVEL
DELAY
TIME
JAZZ CLUB
STADIUM
SPORTS
ROCK
5678
910
RESET CLEAR
MUTING
VOLUME
l6
l8
20
24
28
34
40
50
60
70
l4
l2
l0
8
6
4
3
2
l
0
–dB
Flash
MUTING
When you listen with headphones
Connect the headphones to the PHONES jack. You
can listen to the sound to be output from the main
speakers through headphones.
When listening with headphones privately, set both
the SPEAKERS A and B switches to the OFF position
and switch off the digital sound field processor (so
that the message “EFFECT OFF” is shown on the
display) by pressing the EFFECT switch.
PHONES
22
TUNING OPERATIONS
Normally, if station signals are strong and there is no interference, quick automatic-search tuning (AUTOMATIC
TUNING) is possible. However, if signals of the station you want to select are weak, you must tune to it manually
(MANUAL TUNING).
3,4,
2,
1,
AUTOMATIC TUNING MANUAL TUNING
TUNING
MODE
TUNING
MODE
2
• If the tuning search does not stop at the desired station
(because the signals of the station are weak), change to the
MANUAL TUNING method.
3
To tune to a higher frequency, press the right side once.
To tune to a lower frequency, press the left side once.
4
Select the reception band (FM or AM) while watching
the display.
FM/AM
AUTO
TUNING
1
DOWN
TUNING
UP
If the station where tuning search stops is not the desired
one, press again.
DOWN
TUNING
UP
AM
FM
or
• To continue tuning search, press and hold the button.
Select the reception band (FM or AM) while watching
the display.
FM/AM
DOWN
TUNING
UP
Tune to a desired station manually.
AM
FM
or
“AUTO TUNING” goes off.
Note:
If you tune to an FM station manually, it is received in
monaural mode automatically to increase the signal quality.
Display information 1 Displays the band and frequency of the received
station.
2 Lights up when an FM stereo broadcast is received
in stereo.
3 Indicates the signal level of the received station.
kHz
MHz
AM
FM
STEREO
0
20
l00
40 60
1
2
3
23
PRESET TUNING
Manual Preset Tuning
This unit can store station frequencies (selected by tuning operation) by using the preset station buttons. With this
function, you can select any desired station by only pressing the corresponding preset station button. Up to 40
stations (8 stations × 5 pages) can be stored.
3
2, 4,
To program stations To recall a preset station
MEMORY
2
• In the same way, program other stations to A2, A3, to A8.
3
Flashes for about 5 seconds.
4
Tune to a desired station.
(Refer to the previous page for tuning procedure.)
PRESET
MHz
FM
1
Select a desired page (A - E) of preset station buttons
while watching the display.
Press a preset station button before the “MEMORY”
prompt on the display switches off.
• You can program more stations to the preset station buttons
on other pages in the same way by selecting other pages in
step 2.
A/B/C/D/E
PRESET
MHz
MEMORY
FM
Shows the displayed station has been
programmed to A1.
I 2345678
PRESET STATIONS
FM
Select the page of preset station buttons.
I 2345678
PRESET STATIONS
Select the desired preset station button.
A/B/C/D/E
PRESET
PRESET
PRESET
FM
Notes:
A new setting can be programmed in place of the former
one.
For presets, the setting of the reception mode (stereo or
monaural) is stored along with the station frequency.
Memory back-up
The memory back-up circuit prevents the pro-
grammed data from being lost even if the POWER
switch is set off or the power plug is disconnected
from the AC outlet or the power is cut due to tempo-
rary power failure. If, however, the power is cut for
more than one week, the memory may be erased. If
so, it can be re-programmed by simply following the
PRESET TUNING steps.
24
Automatic Preset Tuning
You can also make use of an automatic preset tuning function for FM stations only. By this function, this unit
performs automatic tuning and stores FM stations with strong signals sequentially. Up to 40 stations are stored
automatically in the same way as in the manual preset tuning method on page 23.
2
1
3
To program stations
If you want to store the first station received by the
automatic preset tuning to a desired preset station
number.
If, for example, you want to store the first received
station to C5, select “C5” by using the A/B/C/D/E
button and the preset station buttons after pressing
the MEMORY button in step 2. Then press the
TUNING button. The first received station is stored to
C5, and next stations to C6, C7, etc., sequentially.
If stations are stored up to E8, the automatic preset
tuning is finished automatically.
When the automatic preset tuning is finished
The display shows the frequency of the last preset
station.
Check the contents and the number of preset stations
by following the procedure of the section “To recall a
preset station” on page 23.
To recall a preset station
Simply follow the procedure of the section “To recall
a preset station” on page 23.
Notes:
You can replace a preset station by another FM or AM
station manually by simply following the procedure of
the section “To program stations” on page 23.
If the number of received stations is not enough to be
stored up to E8, the search is finished automatically
when it reaches the highest frequency after searching
through all frequencies.
With this function, only FM stations with sufficient
signal strength are stored automatically. If the station
you want to program is weak in signal strength, tune to
it in monaural manually and program it by following the
procedure of the section “To program stations” on page
23.
3
To tune to higher frequencies, press right side once.
To tune to lower frequencies, press left side once.
FM/AM
1
DOWN
TUNING
UP
FM
MEMORY
2
Press and hold for about 3 seconds.
Flashes
PRESET
MHz
MEMORY
FM
STEREO
0
20
l00
40 60
• If the TUNING button is not pressed, in a while the
automatic preset tuning begins automatically toward higher
frequencies.
The automatic preset tuning begins from the frequency
currently displayed. Received stations are programmed to
A1, A2, to A8 sequentially.
• If more than 8 stations are received, they are also
programmed to the preset station numbers on other pages
(B, C, D and E) in that order.
25
Exchanging Preset Stations
You can exchange the places of two preset stations with each other as shown below.
2,4
(Example)
If you want to shift the preset station on E1 to A5, and
vice versa.
2
3
4
Recall the preset station on E1 (by following the method
of “To recall a preset station” on page 23).
1
Next, recall the preset station on A5 by following the
procedure in step 1.
Shows the exchange of stations is completed.
EDIT
MEMORY
MEMORY
MEMORY
EDIT
26
USING THE DIGITAL SOUND FIELD PROCESSOR (DSP)
This unit incorporates a sophisticated, multi-program digital sound field processor, which allows you to expand
and shape the audio sound field from both the audio and video sources, for a theater-like experience in the listen-
ing/viewing room.
This digital sound field processor has 10 programs; 8 programs for digital sound field processing and 2 programs
for the Dolby Pro Logic Surround sound system (DOLBY PRO LOGIC and DOLBY PRO LOGIC ENHANCED).
You can create an excellent audio sound field by selecting the suitable program and adding desired adjustments. In
addition, when the DOLBY PRO LOGIC, DOLBY PRO LOGIC ENHANCED, or 70␣ mm MOVIE THEATER pro-
gram is selected, the built-in automatic input balance control functions. This presents you the best surround
condition without manual adjustment.
DELAY TIME
CENTER REAR
CENTER
MODE
JAZZ CLUB
ROCK
CONCERT
CONCERT
HALL
PRO LOGIC
ENHANCED
TV
THEATER
SPORTS
STADIUM
DIGITAL SOUND FIELD PROCESSOR
VIDEO AUX
VCR 2 VCR 1
LD/TV
TAPE 2
MONITOR
TUNER CD PHONO
EFFECT
345678
PRESET STATIONS
CINEMA DSP
7ch
2090
LEVEL
MOVIE THEATER
70mm
CHURCH
TAPE 1
FRONT
BASS TREBLE BALANCE
5
0
l
2
3
4
55
4
3
2
l
0
l
2
3
4
55
4
3
2
l
0
l
2
3
4
LR
VIDEO AUX
8 VIDEO VIDEO L AUDIO R
REC OUT
LD/TV
VCR 1
TAPE 1
TUNER
CD
PHONO
VIDEO AUX
VCR 2
SOURCE
2CH/5CH DISCRT
WIDE
PRO LOGIC
21
34 5 6
7
MASTER
VOLUME
+
TEST
MUTING
++
+
+
DSP
HALL
EFFECT
CHURCH
FRONT LEVEL
CENTER LEVEL
REAR LEVEL
DELAY
TIME
910
ON/OFF
RESET CLEAR
1 CENTER MODE
Selects the center channel output mode. (For details, refer to page 17.)
2 Displays your selection on the DSP or other informations.
3 DELAY TIME –/+
Adjusts the delay time. (For details, refer to page 30.)
4 CENTER and LEVEL –/+
FRONT and LEVEL –/+
REAR and LEVEL –/+
Adjusts sound output level at each speaker. (For details, refer to page 29.)
5 Selects a digital sound field program.
6 EFFECT
Switches on/off the digital sound field processor (DSP).
7 TEST
Used for speaker balance adjustment. (For details, refer to page 17.)
27
Description of Each Sound Field Program
The following list gives brief descriptions of the sound fields produced by each of the DSP programs. Keep in mind
that most of these are precise digital recreations of actual acoustic environments. The data for them was recorded at
the locations described using sophisticated sound field measurement equipment.
Note:
The channel level balance between the left rear effect speaker and the right rear effect speaker may vary de-
pending on the sound field you are listening to. This is due to the fact that most of these sound field recreations
are actual acoustic environments.
PROGRAM FEATURE
PRO LOGIC This program is effective for playback of sources encoded with Dolby Surround. The employ-
ment of the digital signal processing system reduces crosstalk and transfers the sound
source more smoothly and precisely, compared to conventional types. A stable movie sound
field is recreated.
PRO LOGIC ENHANCED This program is effective for playback of sources encoded with Dolby Surround. Enhancing
the “Normal” Dolby Pro Logic, the DSP technology simulates the multi-surround speaker
systems of a 35 mm film theater, thus widening the surround-sound field with greater
presence.
70 mm MOVIE THEATER This program is effective for playback of sources encoded with Dolby Surround.
The Yamaha DSP technology is ideally combined with the Dolby Pro Logic to present you the
incredible listening experience of the 70 mm movie theater. This program is ideal for pre-
cisely reproducing the sound design of the newest movies. The sound field is made accord-
ing to the design of the latest movie theaters, so the reverberations of the sound field itself
are restrained as much as possible. The three-dimensional feeling of the sound field is
emphasized and dialog is precisely oriented on the screen. You can enjoy watching science-
fiction, action, and adventure movies with this program.
TV THEATER This program is suitable for dramas, variety or music programs, etc. Much surround effect
can be gained for stereo sources.
SPORTS This program is furnished with a tight sound field in which the sound will not spread exces-
sively on the front side, but the rear surround produces a dynamic sound expansion. This
program is most suitable for sports programs encoded with Dolby Surround
STADIUM This program gives you long delays between direct sounds and effect sounds, and the
extraordinarily spacious feel of a large stadium.
ROCK CONCERT This program is suitable for rock music. A big, powerful sound is reproduced lively and
dynamically.
JAZZ CLUB This is a small, cosy jazz club with a low ceiling. The sound is very close and intimate.
CHURCH This program recreates the acoustic environment of a modern church with a high pointed
dome and columns along the sides. This interior produces very few primary reflections.
CONCERT HALL In this program, the center seems deep behind the front speaker pair, creating an expansive,
large hall ambience.
Description of Dolby Pro Logic Surround
DOLBY PRO LOGIC SURROUND: This unit
employs the Dolby Pro Logic Surround system. This
system is similar to professional Dolby Stereo decod-
ers used in movie theaters.
By employing a four-channel system, the Dolby Pro
Logic Surround system divides the input signals into
four levels: the left and right main channels, the center
channel (to characterize dialog), and the rear sur-
round-sound channels (to characterize sound effects,
background noise and other ambient noise).
Dolby Surround is encoded on the sound track of
commercially available video cassettes and video
discs as well. When you play a source encoded with
Dolby Surround on your home video system, the
Dolby Pro Logic Surround system in this unit decodes
the signal and feeds the surround-sound effects.
The Dolby Pro Logic Surround mode may not be
always effective on video sources not encoded with
Dolby Surround.
Manufactured under license from Dolby Laboratories
Licensing Corporation. Additionally licensed under
Canadian patent number 1,037,877. “Dolby”, “AC-3”,
“Pro Logic”, and the double-D symbol are trademarks
of Dolby Laboratories Licensing Corporation.
28
To play a source with the digital sound field processor
2
3
Notes:
If you prefer to cancel the DSP, press the EFFECT
switch. The sound will be the normal 2-channel stereo
without surround sound effect.
When STADIUM, ROCK CONCERT, JAZZ CLUB,
CHURCH, or CONCERT HALL is selected, no sound is
heard from the center speaker.
When a monaural sound source is played with DOLBY
PRO LOGIC or DOLBY PRO LOGIC ENHANCED,
no sound is heard from the main speakers, the front
speakers, and the rear speakers. Sound is heard only from
the center speaker. However, if the center channel mode
is in PHANTOM, the main speakers output the sound of
the center channel.
When this unit’s Dolby Pro Logic Surround system is
used, if the main-source sound is considerably altered by
over adjustment of the BASS or TREBLE controls, the
relationship between the center and rear channels may
produce an unnatural effect.
Dolby Surround AC-3
Dolby Surround AC-3 is the next generation of multi-
channel consumer audio. It uses a low bit-rate audio
encoding scheme, creating a single composite data
stream that contains five high-quality full-range
channels, plus a sixth low frequency effect channel
(called “5.1”).
This unit is equipped with 5 CH DISCRT terminals
for Dolby Surround AC-3.
To listen to a 5 CH DISCRT SOURCE:
Press the LD/TV button so that “5 CH DISCRT”
appears on the display. To cancel it, press the switch
again.
LD/TV
When you switch to “5 CH DISCRT” mode, the
Digital Sound Field processor features of this unit
are no longer available. The CENTER MODE
switch, DELAY TIME switch and EFFECT switch
also no longer work.
Signals connected to the 5CH DISCRT INPUT are
not output to the tape decks or video recorders.
To record the signals from an LD player, you must
connect the player to the LD/TV terminals.
If desired, adjust the delay time and the output level of
each speaker. (For details, refer to the corresponding
descriptions on page 29, 30.)
1
2 Select the desired program that is suitable for the source.
3
JAZZ CLUB
ROCK
CONCERT
CONCERT
HALL
PRO LOGIC
ENHANCED
TV
THEATER
SPORTS
STADIUM
DIGITAL SOUND FIELD PROCESSOR
MOVIE THEATER
70mm
CHURCH
Follow steps 1 - 6 shown in “BASIC OPERATIONS”
on page 19.
The selected program name is shown on the display.
PRO LOGIC
29
The following adjustments can be done on the remote control transmitter as well as on the front panel.
Adjustment of the FRONT LEVEL
You can “fine-tune” the sound output level of the
front effects speakers after setting the output level
according to the instructions in “Speaker balance
adjustment” on page 16.
LEVEL
FRONT
Press the “+” or “FRONT LEVEL key on the
remote control transmitter. As you change the volume
level, the front panel LCD will display the value. If
you press the “+” or “–” key continuously, the level
will continuously change except for a momentary
pause at the preset point (80).
Once the output level is adjusted, the level value
will be the same in all the digital sound field
programs.
Note:
When 5 CH DISCRT or DOLBY PRO LOGIC is used, the
FRONT LEVEL control will not function.
Adjustment of the CENTER LEVEL
You can adjust the sound output level of the center
channel speaker even if the output level is already set
in “Speaker balance adjustment” on page 16.
CENTER
LEVEL
Press the “+” or “CENTER LEVEL key on the
remote control transmitter. As you change the volume
level, the front panel LCD will display the value. If
you press the “+” or “” key continuously, the level
will continuously change except for a momentary
pause at the preset point (80).
The center channel speaker is used only in DOLBY
PRO LOGIC, DOLBY PRO LOGIC ENHANCED,
70 mm MOVIE THEATER, TV THEATER, SPORTS
and 5 CH DISCRT modes.
Once the output level is adjusted, the level value
will be the same in all the digital sound field
programs.
Note:
If the digital sound field program STADIUM, ROCK
CONCERT, JAZZ CLUB, CHURCH, or CONCERT
HALL is selected, the CENTER LEVEL control will not
function.
Adjustment of the REAR LEVEL
You can adjust the sound output level of the rear
speakers even if the output level is already set in
“Speaker balance adjustment” on page 16.
REAR
LEVEL
Press the “+” or “REAR LEVEL key on the remote
control transmitter, the level value changes continu-
ously. However, the value stops changing momen-
tarily at the preset point (80).
Once the output level is adjusted, the level value
will be the same in all the digital sound field
programs.
30
Adjustment of DELAY TIME
You can adjust the time difference between the beginning of the source sound and the beginning of the effect
sound with the DELAY TIME control.
The DELAY TIME control is effective with all programs.
By applying more or less delay, sound effects, background noise, and ambient noise coming at you from the rear
speakers can be enhanced or subdued for extra effect.
1. PRO LOGIC from 15 to 30 milliseconds (Preset value: 20 ms)
2. PRO LOGIC ENHANCED from 15 to 30 milliseconds (Preset value: 20 ms)
3. 70 mm MOVIE THEATER from 15 to 30 milliseconds (Preset value: 17 ms)
4. TV THEATER from 1 to 50 milliseconds (Preset value: 28 ms)
5. SPORTS from 1 to 50 milliseconds (Preset value: 20 ms)
6. STADIUM from 1 to 50 milliseconds (Preset value: 45 ms)
7. ROCK CONCERT from 1 to 50 milliseconds (Preset value: 22 ms)
8. JAZZ CLUB from 1 to 50 milliseconds (Preset value: 26 ms)
9. CHURCH from 1 to 50 milliseconds (Preset value: 40 ms)
10. CONCERT HALL from 1 to 50 milliseconds (Preset value: 30 ms)
By continuously pressing “+” or “” on the DELAY
TIME control, the value changes continuously.
However, the value stops changing momentarily at
the preset point.
DELAY TIME
Note:
Adding too much delay will cause an unnatural effect with
some sources. Experiment with the DELAY TIME control
to create the effect that you find most suitable.
Note:
The values of the DELAY TIME, CENTER LEVEL,
FRONT LEVEL and REAR LEVEL you set the last time
will remain memorized even when the power of this unit is
off.
However, if the power cord is kept disconnected for more
than one week, these values will be automatically changed
back to the original factory settings.
31
SETTING THE SLEEP TIMER
If you use the SLEEP timer of this unit, you can make this unit turn off automatically. When you are going to sleep
while enjoying a broadcast or other desired input source, this timer function is helpful.
Notes:
The SLEEP timer can be controlled only with the remote control transmitter.
The components on which the SLEEP timer is effective are the sources connected to the SWITCHED AC OUTLET(S) on
the rear panel of this unit.
To set the SLEEP time To cancel the selected SLEEP time
The unit will be turned off automatically at the selected
SLEEP time.
1
Whenever the SLEEP key is pressed, the SLEEP time
will change as follows:
After a while, the display returns to the indication before
the SLEEP timer is set, and the “SLEEP” indicator stops
flashing and lights up.
SLEEP
Flashes continuously.
(Minutes)
The SLEEPtimer is OFF.
(The indication before the
SLEEP key is pressed.)
2
1
Press once or more so that the display returns to the
indication before the SLEEP timer is set. (“SLEEP” will
go off from the display.)
SLEEP
Press the SLEEP key until
“SLEEP OFF” appears on
the display.
SLEEPSLEEP
SLEEP
Note:
The SLEEP timer setting can also be canceled by turning
off the power with the POWER switch or disconnecting the
power plug of this unit from the AC outlet.
32
REMOTE CONTROL TRANSMITTER
Battery installation
Main Room Remote
1
2
3
Room 2 Remote
2
3
1
Battery replacement
If you find that the remote control transmitter must be
used closer to the main unit, the batteries are weak.
Replace both batteries with new ones.
Notes:
Use only AA, LR6, UM-3 batteries for replacement.
Be sure the polarities are correct. (See the illustration
inside the battery compartment.)
Remove the batteries if the remote control transmitter
will not be used for an extended period of time.
If batteries leak, dispose of them immediately. Avoid
touching the leaked material or letting it come in contact
with clothing, etc. Clean the battery compartment
thoroughly before installing new batteries.
Remote control transmitter operation range
Remoto control
sensor
30°
30°
Within approximately
7 m (23 feet)
Notes:
There should be no large obstacles between the remote
control transmitter and the main unit.
If the remote control sensor is directly illuminated by
strong lighting (especially an inverter type of fluorescent
lamp etc.), it might cause the remote control transmitter
not to work correctly. In this case, reposition the main
unit to avoid direct lighting.
STANDBY mode (Singapore model only)
While the power is on, pressing the POWER key on
the remote control transmiter switches the unit to the
STANDBY mode. (In this mode, the indicator is half
illuminated.)
POWER on mode STANDBY mode
33
The remote control transmitter provided with this unit is designed to control all the most commonly used functions
of the unit. If the CD player, tape deck, etc. connected to this unit are YAMAHA components designed for remote
control compatibilty, then this remote control transmitter will also control various functions of each component.
When you operate this unit and/or other YAMAHA components with this remote control transmitter, set the
YPC-USER-LEARN switch to the YPC (Yamaha Preset Code) position.
For Control of This Unit
Main Room Remote Room 2 Remote
+
+
PLAY
DIR A DIR B
SKIP
STOP
STOP PLAY
TV VCR AUX
DISC
SKIP
SEARCH
SEARCH
SEARCH
PAUSE/STOP
PAUSE/STOP
DECK
A/B
REC/PAUSEREC MUTE
PLAY
CHAPTER/CH
DISPLAY
TEST
+
+
+
TRANSMIT
/LEARN
FRONT LEVEL
CENTER LEVEL
REAR LEVEL
DELAY
TIME
YPC LEARN
USER
RESET CLEAR
MASTER
VOLUME
MUTING
+
+
POWER
TAPE 1
PHONO
CD
TUNER
VCR 1
VCR 2
V–AUX
SLEEP
PRESET
TAPE 2 MON
LD/TV
DSP
EFFECT
CHURCH
MOVIE THEATER
PRO LOGIC
ENHANCED
THEATER
70mm TV
1234
5678
910
ON/OFF
HALL
JAZZ CLUB
STADIUM
SURROUND
SPORTS
ROCK
A B C D E
PHONO
CD
+
TAPE 1
TAPE 2
LD/TV
PRESET
TUNER
VCR 1
VCR 2
V–AUX
SKIP
PLAY
PAUSE/STOPDISC SKIP
DIR A
DECK
A
/
B
DIR B
STOP
+
PLAY
PAUSE/STOP
PLAY
STOP
CHAPTER
REMOTE BOURCE
CONTROLER
A B C D E
POWER
Turns the power on/off.
SLEEP
Refer to “SETTING THE
SLEEP TIMER” on page
31.
Tuner keys
Controls tuner.
+: Selects higher preset
station number.
–: Selects lower preset
station number.
A/B/C/D/E
Selects the page (A - E)
of preset station buttons.
For the DSP control keys,
refer to the page 26.
Input selector keys
Selects input source.
(MASTER) VOLUME +/–
Turns the volume level
up/down.
Input selector keys
Selects input source.
+: Selects higher preset
station number.
–: Selects lower preset
station number.
A/B/C/D/E
Selects the page (A - E)
of preset station
buttons.
Tuner keys
Controls tuner.
Muting Key
Mutes the master volume.
While mute is engaged, an
indicator on the master
VOLUME control flashes.
Press again to un-mute the
master volume.
34
For Other Component Control
Identify the remote control transmitter keys with your component’s keys. If these keys are identical, their functions
will be the same. On each key function, refer to the corresponding instruction on your component’s manual.
+
A B C D E
PRESET
PHONO
CD
TAPE 1
TAPE 2
LD/TV
TUNER
VCR 1
VCR 2
V–AUX
REMOTE BOURCE
CONTROLER
PLAY
DIR A DIR B
SKIP
STOP
STOP PLAY
DISC
SKIP
SEARCH
SEARCH
SEARCH
PAUSE/STOP
PAUSE/STOP
DECK
A/B
REC/PAUSEREC MUTE
PLAY
CHAPTER/CH
+
DISPLAY
+
POWER
TAPE 1
PHONO
CD
TUNER
VCR 1
SLEEP TV VCR AUX
PRESET
TAPE 2 MON
LD/TV
TRANSMIT
/LEARN
YPC LEARN
USER
A B C D E
SKIP
PLAY
PAUSE/STOPDISC SKIP
DIR A
DECK
A
/
B
DIR B
STOP
+
PLAY
PAUSE/STOP
PLAY
STOP
CHAPTER
1
2
3
1
2
3
1 CD player keys
Controls compact disc player.
DISC SKIP is applicable only to compact disc changer.
2 Tape deck keys
Controls tape deck.
DIR A, B and DECK A/B are applicable only to double cassette tape deck.
For a single cassette deck with automatic reverse function, pressing DIR A will reverse the direc-
tion of tape running.
3 LD player keys
Controls LD player.
Using the Remote Transmitters
If you use the Room 2 Remote transmitter (the transmitter for the second room) in the main room, the input
selector keys of this remote affect the settings in the second room, not the main room. The other keys on the
transmitter work the same in both the main room and the second room.
If you use the Main Remote transmitter (the transmitter for the main room) in the second room, the keys that
appear on the Room 2 Remote transmitter work except the input selector keys.
The indicator information:
1 Lights up momentarily when the Room 2 Remote transmitter is used in
the main room.
2 Lights up momentarily when the Room 2 Remote transmitter is used in
the second room.
ROOM 2
ROOM 2
CONTROL
ROOM 2
1
2
35
REMOTE CONTROL “LEARNING” FUNCTION
All of the keys on this remote control transmitter can be programmed to “learn” key-functions from other remote
control transmitters without losing the preset key functions. By using this feature, this unit can then be used in
place of one or more other remote control transmitters, thus making operation of your various audio and video
components more convenient. Use the included user program sheets to indicate a new function learned for each
key.
Note:
There may occasionally be instances in which, due to the signal-coding and modulation employed by the other remote control
transmitter, this unit will not be able to “learn” its signals.
TRANSMIT/LEARN indicator
YPC-USER-LEARN switc
RESET button
Press this button to “reset” the
internal microcomputer which
controls remote control
operations. Microcomputer
“reset” is necessary when the
remote control freezes.
Blank keys
These keys have no preset
functions and are used only for
learning other remote control
transmitter’s functions.
CLEAR button
This button is used to clear one or
all learned key functions. (Refer
to page 37.)
Pressing the RESET button will
not erase learned functions.
“YPC” is the abbreviation of YAMAHA
Preset Code.
USER : Set to this position when using
“learned” key functions.
LEARN : Set to this position when learning
new key functions from other
remote control transmitters.
YPC : Set to this position when using preset
key functions (for controlling this unit
and/or YAMAHA components).
+
1234
5678
+
POWER
PLAY
TAPE 1
DIR A DIR B
SKIP
PHONO
CD
TUNER
STOP
VCR 1
VCR 2
STOP PLAY
V–AUX
SLEEP
DISC
SKIP
SEARCH
SEARCH
SEARCH
PAUSE/STOP
PAUSE/STOP
DECK
A/B
PRESET
A B C D E
REC/PAUSEREC MUTE TAPE 2 MON
PLAY LD/TV
CHAPTER/CH
DISPLAY
MASTER
VOLUME
+
TEST
MUTING
++
+
+
DSP
HALL
EFFECT
CHURCH
FRONT LEVEL
CENTER LEVEL
REAR LEVEL
DELAY
TIME
MOVIE THEATER
JAZZ CLUB
STADIUM
PRO LOGIC
SURROUND
SPORTS
ENHANCED
ROCK
THEATER
70mm TV
910
ON/OFF
TV VCR AUX
TRANSMIT
/LEARN
YPC LEARN
USER
RESET CLEAR
36
To learn a new function
1
2
3
YPC LEARN
USER
Set to the “LEARN” position.
Press a key on this unit where a new function will be
learned.
About 5–10 cm (2–4 in).
Press and hold the key (on the other remote control
transmitter) where the desired new function is.
Lights up
• When the TRANSMIT/LEARN indicator stops lighting, the
learning is finished.
4
Repeat step 2 and 3 until all desired functions are
successfully learned.
5
Set to the “USER” position.
Try operating your components.
YPC LEARN
USER
Notes:
When you operate the desired component with this
remote control transmitter, TRANSMIT/LEARN
indicator will flash steadily.
The originally preset function of a key is still available in
the USER position if a new function has not been
learned to the key.
Successful learning to a key results in the erasure of
previously learned functions and their replacement by
the newly learned ones.
If there is no more room in the memory area for a
function to be learned, the TRANSMIT/LEARN
indicator will flash on and off. In this case, even if some
keys are not occupied with functions from other remote
control transmitters, no further learning is possible.
Memory back-up
All of the learned functions will be retained while you
replace the batteries. However, if no batteries are
installed for a few hours, the learned functions will be
erased and will have to be learned again.
37
To clear a learned function To clear all learned functions
Troubleshooting guide
SYMPTOM CAUSE REMEDY
Replace the batteries with new ones and press the
RESET button on the remote control transmitter.
The internal microcomputer “freezes”. Replace the batteries (and press the RESET button
for this remote control transmitter).
Place the remote control transmitters with the
proper distance.
Learning is not possible.
Further learning is not possible without deleting
unnecessary commands.
Memory capacity is full. Press the RESET button on the remote control
transmitter.
The remote control transmitter does not work.
Learning cannot be made successfully. (The
TRANSMIT/LEARN indicator does not light up or
flash.)
The batteries of this remote control transmitter are
weak.
The batteries of this remote control transmitter
and/or the other remote control transmitter are
weak.
The distance between the two remote control
transmitters is too long or too short.
The signal coding or modulation of the other
remote control transmitter is not compatible with
this remote control transmitter.
2
• To clear two or more functions, repeat step 2 and 3.
3
1
Press and hold the CLEAR button using the point of a
mechanical pencil, etc.
Set to the “USER” position.
Press and hold the key where the learned function to be
deleted is until the indicator flashes 3 times.
CLEAR
TRANSMIT
/LEARN
2
3
1
Press and hold the CLEAR button using the point of a
mechanical pencil, etc.
Set to the “LEARN” position.
Press and hold any key until the indicator flashes 7 times
CLEAR
TRANSMIT
/LEARN
YPC LEARN
USER
YPC LEARN
USER
Note:
If a key is not pressed soon after the CLEAR button is
pressed, this unit will automatically return to the status
that was in effect before the CLEAR button was pressed.
38
The unit fails to turn on when the POWER
switch is pressed.
The volume level cannot be increased, or
sound is distorted.
There is distortion and clear reception cannot
be obtained even with a good FM antenna.
A desired station cannot be tuned in with
Auto tuning.
A desired station cannot be tuned in with
Auto tuning.
There are continuous crackling and hissing
noises.
There are buzzing and whining noises
(especially in the evening).
The sound is degraded when monitoring is
performed by using the headphones connected to
the compact disc player or cassette deck which
are connected with this unit.
TROUBLESHOOTING
If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by
the simple measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column,
disconnect the power cord and contact your authorized YAMAHA dealer or service center for help.
SYMPTOM CAUSE REMEDY
Firmly plug in the power cord.
No sound or no picture. Incorrect output cord connections. Connect the cords properly. If the problem persists,
the cords may be defective.
Appropriate input selector is not pressed. Press the appropriate input selector corresponding
to the input source.
The sound suddenly goes off. Turning the unit off and then on will reset the
protection circuit.
The SLEEP timer functioned. Do not make the SLEEP timer function.
Only one side speaker outputs the sound. Incorrect setting of the BALANCE control. Adjust it to the appropriate position.
Incorrect cord connections. Connect the cords properly. If the problem persists,
the cords may be defective.
Sound “hums”. Incorrect cord connections. Firmly connect the audio plugs. If the problem
persists, the cords may be defective.
Make the GND connection between the turntable
and this unit.
The volume level is low while playing a record. The player should be connected to the unit through
the MC head amplifier.
Turn the power to the component on.
No sound from the rear speakers. Turn up the sound output level with the REAR
LEVEL control.
Select another program suitable for the monaural
sound source.
No sound from the center speaker. Turn up the sound output level with the CENTER
LEVEL control.
The center channel mode is in PHANTOM mode. Select NORMAL or WIDE.
Incorrect sound field program selection. Select the appropriate program.
No sound field program is selected.
FM stereo reception is noisy. Check the antenna connections. Try using a
multiple element FM antenna.
There is multipath interference. Adjust antenna placement to eliminate multipath
interference.
The station is too weak. Use Manual tuning mode. Use a high quality
directional FM antenna.
Weak signal or loose antenna connections. Tighten the AM loop antenna connections and
rotate it for best reception. Use Manual tuning
mode.
Use an outdoor antenna and a ground wire. This
will help somewhat but it is difficult to eliminate all
noise.
A television set is being used nearby. Relocate this unit away from the TV.
The remote control transmitter does not work. Change the position of the main unit.
Replace the batteries with new ones.
The power to this unit is off. Turn the power to this unit on.
Power cord is not plugged in or is not completely
inserted.
The protection circuit has been activated because
of short circuit etc.
No connection from the turntable to the GND
terminal.
The record is being played on a turntable with an
MC cartridge.
The power to the component connected to the
REC OUT terminals of this unit is off.
The sound output level to the rear speakers is set
to 0.
The monaural sound source is played in DOLBY
PRO LOGIC or DOLBY PRO LOGIC ENHANCED
mode.
The sound output level to the center speaker is set
to 0.
Because of the characteristics of FM stereo
broadcasts, this is limited to cases where the
transmitter is too far away or the antenna input is
poor.
Noises will result from lighting, fluorescent lamps,
motors, thermostats and other electrical
equipment.
Direct sunlight or lighting (of an inverter type of
fluorescent lamp etc.) is striking the remote control
sensor of the main unit.
The batteries of this remote control transmitter are
too weak.
others
Remote control transmitter
AM FM Amplifier
39
SPECIFICATIONS
AUDIO SECTION
Minimum RMS Output Power per Channel
MAIN L, R
8 ohms, 20 Hz to 20 kHz, 0.015% THD
.................................................................. 100W+100W
6 ohms, 20 Hz to 20 kHz, 0.04% THD
[U.S.A. model only] .......................... 120W+120W
Center
8 ohms, 1 kHz, 0.015% THD ......................... 100W
Front L, R
8 ohms, 1 kHz, 0.08% THD .................. 35W+35W
Rear L, R
8 ohms, 1 kHz, 0.08% THD .................. 35W+35W
Maximum Output Power [General model only]
8 ohms, 1 kHz, 10% THD (MAIN L/R)
............................................................. 135W+135W
Dynamic Power per Channel
(by IHF Dynamic Headroom measuring method)
8/6/4/2 ohms ...................... 130/160/215/310W
Dynamic Headroom
[U.S.A. and Canadian models only]
8 ohms .......................................................... 1.14 dB
Power Band Width
8 ohms, 50W, 0.08% THD
....................................................... 10 Hz to 50 kHz
Damping Factor
8 ohms, 20 Hz to 20 kHz ....................200 or more
Input Sensitivity/Impedance
PHONO MM ........................... 2.5 mV/47 k-ohms
5 ch DISCRT/CD/TAPE/LD·TV/VCR
..................................................150 mV/47 k-ohms
MAIN IN ...................................... 1.0V/47 k-ohms
Maximum Input Signal
PHONO MM (1 kHz 0.02% THD)
....................................................... 110 mV or more
CD/TAPE/LD·TV/VCR (EFFECT ON)
(1 KHZ 0.5% THD) ........................... 2.2V or more
Output Level/Impedance
REC OUT ............................... 150 mV/1.0 k-ohms
PRE OUT (MAIN) ...................... 1.0V/1.5 k-ohms
ROOM 2 OUT .........................150mV/1.5 k-ohms
LPF (EFFECT OFF) .................... 3.5V/2.7 k-ohms
Headphone Jack Rated Output/Impedance
(8 ohms, 1 kHz, 150 mV) ............0.55V/390 ohms
Frequency Response (20 Hz to 20 kHz)
MAIN IN .................................................... 0±0.2 dB
CD/TAPE/LD·TV/VCR (MAIN L/R)
..................................................................... 0±0.5 dB
RIAA Equalization Deviation
PHONO MM ............................................. 0±0.5 dB
Total Harmonic Distortion
PHONO MM to REC OUT
20 Hz to 20 kHz, 1V ................... 0.01% or less
CD/TAPE/LD·TV/VCR (EFFECT OFF) to SP OUT
20 Hz to 20 kHz 50W/8 ohms 0.015% or less
CD/TAPE/LD·TV/VCR to SP OUT FRONT, REAR
1 kHz, 17.5W/8 ohms .................. 0.3% or less
Signal-to-Noise Ratio (IHF-A Network)
PHONO MM to REC OUT (5 mV Input Shorted)
........................................................... 86 dB or more
CD/TAPE/LD·TV/VCR to SP OUT
(InputShorted, EFFECT OFF) ........ 98 dB or more
Residual Noise (IHF-A Network)
SP OUT (MAIN L/R) ..................... 170 µV or less
Channel Separation
(Vol. –30 dB, EFFECT OFF)
PHONO MM (Input Shorted 1 kHz/10 kHz)
................................60 dB or more/55 dB or more
CD/TAPE/LD·TV/VCR
(Input 5.1 k-ohms Shorted 1 kHz/10 kHz)
................................60 dB or more/45 dB or more
Tone Control Characteristics
BASS: Boost/cut .............................±10 dB (50 Hz)
Turnover Frequency..................... (350 Hz)
TREBLE: Boost/cut .................... ±10 dB (20 kHz)
Turnover Frequency .............. (3.5 kHz)
Filter Characteristics
LPF (fc=200 Hz) ....................................... 6 dB/oct
Gain Tracking Error (0 to –70 dB)
................................................................3 dB or less
Tuner Output Level/Impedance
FM 100% MOD, 1 kHz .........500 mV/2.2 k-ohms
AM 30% MOD, 1 kHz ..........150 mV/2.2 k-ohms
Bass Extension...................................... +6 dB (50 Hz)
Muting .......................................................................
VIDEO SECTION
Video Signal Type
[U.S, Canadian and General models] ........ NTSC
[Australian, Singapore and General models]
............................................................................PAL
Video Signal Level .......................... 1 Vp-p/75 ohms
S-Video Signal Level
Y ................................................... 1 Vp-p/75 ohms
C ............................................ 0.286 Vp-p/75 ohms
Maximum Input Level ...................1.5 Vp-p or more
Signal-to-Noise Ratio .......................... 50 dB or more
Monitor Out Frequency Response
............................................ 5 Hz to 10 MHz, –3 dB
FM TUNER SECTION
Tuning Range
[U.S.A. and Canadian models]
.................................................... 87.5 to 107.9 MHz
[Australian, Singapore and General models]
.................................................... 87.5 to 108.0 MHz
50 dB Quieting Sensitivity (IHF, 75 ohms)
Mono ........................................... 1.55 µV (15.1 dBf)
Stereo ............................................. 21 µV (37.7 dBf)
Usable Sensitivity (75 ohms)
(30 dB S/N Quieting, 1 kHz, 100% mod.)
......................................................... 0.8 µV (9.3 dBf)
Image Response Ratio ........................................ 45 dB
IF Response Ratio ............................................... 80 dB
Spurious Response Ratio ................................... 70 dB
AM Suppression Ratio ....................................... 55 dB
Capture Ratio ..................................................... 1.5 dB
Alternate Channel Selectivity ........................... 85 dB
Signal-to-Noise Ratio (IHF)
Mono/Stereo ..................................... 80 dB/75 dB
Harmonic Distortion (1 kHz)
Mono/Stereo ............................................ 0.1/0.2%
Stereo Separation (1 kHz) .................................. 50 dB
Frequency Response
20 Hz to 15 kHz ........................................0 ±1.5 dB
AM TUNER SECTION
Tuning Range
[U.S.A., Canadian and General models]
....................................................... 530 to 1,710 kHz
[Australian and Singapore models]
....................................................... 531 to 1,611 kHz
Usable Sensitivity ....................................... 100 µV/m
Selectivity............................................................. 32 dB
Signal-to-Noise Ratio ......................................... 50 dB
Image Response Ratio ........................................ 40 dB
Spurious Response Ratio ................................... 50 dB
Harmonic Distortion (1 kHz) ............................. 0.3%
GENERAL
Power Supply
[U.S.A. and Canadian models]
....................................................... AC 120V, 60 Hz
[Australian model] ..................... AC 240V, 50 Hz
[General model]
........................... AC 110/120/220/240V, 50/60 z
[Singapore model] ........................ AC230V, 50Hz
Power Consumption
[U.S.A. model] ................................................400W
[Canadian model] .......................... 450W/600 VA
[Australian, Singapore and General models]
..........................................................................420W
Maximum Power Consumption
[General models]............................................ 790W
AC OUTLETS
[U.S.A model]
2 SWITCHED OUTLETS .......... 120W max. total
1 UNSWITCHED OUTLET ................ 200W max.
[Canadian model]
2 SWITCHED OUTLETS ........... 120W max. total
1 UNSWITCHED OUTLET ................ 180W max.
[General model]
2 SWITCHED OUTLETS ........... 120W max. total
1 UNSWITCHED OUTLET ................ 200W max.
[Australian model]
1 SWITCHED OUTLET ...................... 120W max.
[Singapore model]
2 SWITCHED OUTLETS ........... 120W max. total
Dimensions (W × H × D)
................................................. 435 × 171 × 470 mm
(17-1/8” × 5-3/4” × 15-3/16”)
Weight ................................................................ 17.8kg
Accessories ..................................... AM loop antenna
Indoor FM antenna
Remote control transmitter × 2
Batteries × 2
User Program Sheets
Specifications are subject to change without notice.
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77321 MARNE-LA VALLEE-CEDEX 2, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
YAMAHA SCANDINAVIA A.B J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
VT26690 Printed in Japan

Documenttranscriptie

RX-V2090 Natural Sound Stereo Receiver CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN OWNER’S MANUAL CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Contents PROFILE OF THIS UNIT ............................ 6 SPEAKER SETUP FOR THIS UNIT ........... 7 CONNECTIONS ......................................... 9 ADJUSTMENT BEFORE OPERATION .... 16 BASIC OPERATIONS .............................. 19 TUNING OPERATIONS ........................... 22 IMPORTANT! Please record the serial number of this unit in the space below. Model: Serial No.: The serial number is located on the rear of the unit. Retain this Owner’s Manual in a safe place for future reference. USING THE DIGITAL SOUND FIELD PROCESSOR (DSP) ................................ 26 SETTING THE SLEEP TIMER ................. 31 REMOTE CONTROL TRANSMITTER ..... 32 WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. • Explanation of Graphical Symbols The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. SAFETY INSTRUCTIONS 1 Read Instructions — All the safety and operating A. The power-supply cord or the plug has been damaged; or instructions should be read before the unit is operated. B. Objects have fallen, or liquid has been spilled into the 2 Retain Instructions — The safety and operating unit; or instructions should be retained for future reference. C. The unit has been exposed to rain; or 3 Heed Warnings — All warnings on the unit and in the operating instructions should be adhered to. D. The unit does not appear to operate normally or exhibits a marked change in performance; or 4 Follow Instructions — All operating and other instructions should be followed. E. The unit has been dropped, or the enclosure damaged. 5 Water and Moisture — The unit should not be used near 16 Servicing — The user should not attempt service the water – for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc. unit beyond those means described in the operating instructions. All other servicing should be referred to qualified service personnel. 6 Carts and Stands — The unit should be used only with a cart or stand that is recommended by the manufacturer. 6A An unit and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the unit and cart combination to overturn. 7 Wall or Ceiling Mounting — The unit should be mounted to a wall or ceiling only as recommended by the manufacturer. 8 Ventilation — The unit should be situated so that its location or position does not interfere with its proper ventilation. For example, the unit should not be situated on a bed, sofa, rug, or similar surface, that may block the ventilation openings; or placed in a built-in installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings. 17 Power Lines — An outdoor antenna should be located away from power lines. 18 Grounding or Polarization — Precautions should be taken so that the grounding or polarization is not defeated. 19 Outdoor Antenna Grounding — If an outside antenna is connected to this unit, be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. EXAMPLE OF ANTENNA GROUNDING 9 Heat — The unit should be situated away from heat sources such as radiators, stoves, or other appliances that produce heat. MAST GROUND CLAMP 10 Power Sources — The unit should be connected to a power supply only of the type described in the operating instructions or as marked on the unit. 11 Power-Cord Protection — Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the unit. 12 Cleaning — The unit should be cleaned only as ANTENNA LEAD IN WIRE ANTENNA DISCHARGE UNIT (NEC SECTION 810-20) ELECTRIC SERVICE EQUIPMENT GROUNDING CONDUCTORS (NEC SECTION 810-21) GROUND CLAMPS POWER SERIVCE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H) NEC – NATIONAL ELECTRICAL CODE recommended by the manufacturer. 13 Nonuse Periods — The power cord of the unit should be unplugged from the outlet when left unused for a long period of time. 14 Object and Liquid Entry — Care should be taken so that objects do not fall into and liquids are not spilled into the inside of unit. 15 Damage Requiring Service — The unit should be serviced by qualified service personnel when: Note to CATV system installer: This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. CAUTION: READ THIS BEFORE OPERATING YOUR UNIT 1 To ensure the finest performance, please read this 2 3 4 5 manual carefully. Keep it in a safe place for future reference. Install your unit in a cool, dry, clean place – away from windows, heat sources, and too much vibration, dust, moisture or cold. Avoid sources of hum (transformers, motors). To prevent fire or electrical shock, do not expose to rain and water. Do not operate the unit upside-down. It may overheat, possibly causing damage. Never open the cabinet. If a foreign object drops into the set, contact your dealer. Do not use force on switches, knobs or cords. When moving the set, first turn the unit off. Then gently disconnect the power plug and the cords connecting to other equipment. Never pull the cord itself. 6 Do not attempt to clean the unit with chemical solvents; this might damage the finish. Use a clean, dry cloth. 7 Always set the volume control to “– ∞” before starting 8 9 10 11 the audio source play: increase the volume gradually to an appropriate level after the play is started. To prevent lightning damage, pull out the power cord and remove the antenna cable during an electrical storm. Be sure to read the “Troubleshooting” section on common operating errors before concluding that your unit is faulty. Do not connect audio equipment to the AC outlets on the rear panel if that equipment requires more power than the outlets are rated to provide. When not planning to use this unit for long periods of time (ie., vacation, etc.), disconnect the AC power plug from the wall outlet. The apparatus is not disconnected from the AC power source as long as it is connected to the wall outlet, even if the apparatus itself is turned off. FCC INFORMATION 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures: 2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA. Relocate either this product or the device that is being affected by the interference. 3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Utilize power outlets that are on different branch (circuit breaker of fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/ reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to coaxial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corp., U.S.A. 6600 Orangethorpe Ave, Buena Park, CA 90620 The above statement apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries. We Want You Listening For A Lifetime YAMAHA and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or distortion – and, most importantly, without affecting your sensitive hearing. Since hearing damage from loud sounds is often undetectable until it is too late, YAMAHA and the Electronic Industries Association’s Consumer Electronics Group recommend you to avoid prolonged exposure from excessive volume levels. SUPPLIED ACCESSORIES After unpacking, check that the following parts are contained. • Remote Control Transmitter Main Remote • Indoor FM Antenna Room 2 Remote SKIP PHONO TRANSMIT USER LEARN /LEARN YPC DISC SKIP POWER SLEEP TV VCR PAUSE/STOP PLAY — PRESET SKIP + A/B/C/D/E TUNER PLAY TAPE 1 STOP TAPE 2 PLAY LD/TV STOP VCR 1 PHONO DISC SKIP SEARCH PAUSE/STOP DECK A/B PRESET DIR A PLAY CD A/B/C/D/E TUNER — + STOP PLAY TAPE 1 REC/PAUSE DIR A DIR B TAPE 2 MON SEARCH PAUSE/STOP PLAY LD/TV CHAPTER/CH DISPLAY STOP VCR 1 VCR 2 SEARCH REC MUTE CD AUX DECK A/B DIR B PAUSE/STOP — CHAPTER + VCR 2 — + PRO LOGIC ENHANCED 70mm MOVIE THEATER TV THEATER 2 3 4 JAZZ CLUB 1 REMOTE BOURCE CONTROLLER V–AUX • AM Loop Antenna SURROUND STADIUM ROCK 5 6 7 CHURCH HALL 9 10 SPORTS V–AUX 8 EFFECT DSP ON/OFF MASTER VOLUME FRONT LEVEL — + + + DELAY TIME REAR LEVEL — + RESET CLEAR + TEST CENTER LEVEL — MUTING — — • Batteries (size AA, LR6, UM-3) 4 • User Program Sheets Features • Seven Speaker Configuration Main: 100 W + 100 W (8Ω) RMS Output Power, 0.015% THD, 20-20,000 Hz 120 W + 120 W (6Ω) RMS Output Power, 0.04% THD, 20-20,000 Hz (USA Model Only) Center: 100 W (8Ω) RMS Output Power, 0.015% THD, 1 kHz Front: 35 W + 35 W (8Ω) RMS Output Power, 0.08% THD, 1 kHz Rear: 35 W + 35 W (8Ω) RMS Output Power, 0.08% THD, 1 kHz • Multi-Room Capability Multi-Room and Multi-Source with two Remote Control Units • Digital Sound Field Processor 10 Programs including “Cinema DSP” 70mm Movie Theater • 5 Channel Discrete Input for Dolby Surround Digital AC-3 • Automatic Input Balance Control for Dolby Surround • Test Tone Generator for Easier Speaker Output Balance Adjustment • 3 Center Channel Modes (NORMAL/WIDE/PHANTOM) • 40-Station Random Access Preset Tuning • Automatic Preset Tuning (FM only) • Preset Station Shifting Capability (Preset Editing) • IF Count Direct PLL Synthesizer Tuning System • Video Signal Input/Output Capability • SLEEP Timer • Remote Control Capability • Program and status messages superimposed on connected video monitor OPEN/CLOSE THE CONTROL DOOR To open the door To close the door When it is not necessary to operate controls inside the control door, close the door. 5 PROFILE OF THIS UNIT You are the proud owner of a Yamaha stereo receiver –an extremely sophisticated audio component. The Digital Sound Field Processor (DSP) built into this unit takes full advantage of Yamaha’s undisputed leadership in the field of digital audio processing to bring you a whole new world of listening experiences. Follow the instructions in this manual carefully when setting up your system, and this unit will sonically transform your room into a totally new listening environment –movie theater, concert hall, and so on. In addition, you get incredible realism from Dolby-encoded video sources using the built-in Dolby Pro Logic Surround Decoder. Please read this owner’s manual carefully and store it in a safe place for later reference. Digital Sound Field Processing What is it that makes live music so good? Today’s advanced sound reproduction technology lets you get extremely close to the sound of a live performance, but chances are you’ll still notice something missing: the acoustic environment of the live concert hall. Extensive research into the exact nature of the sonic reflections that create the ambience of a large hall has made it possible for Yamaha engineers to bring you this same sound in your own listening room, so you’ll feel all the sound of a live concert. Furthermore, our technicians, armed with sophisticated measuring equipment, have even made it possible to capture the acoustics of a variety of venues such as an actual concert hall, theater, etc. to allow you to accurately recreate one of several actual live performance environments, all in your own home. Dolby Pro Logic Surround The Dolby Pro Logic Surround Decoder program lets you experience the dramatic realism and impact of Dolby Surround movie theater sound in your own home. Dolby Pro Logic gets its name from its professional-grade steering logic circuitry, which provides greater effective front and rear channel separation for a much higher degree of realism than the “passive” Dolby Surround circuits found in less sophisticated home audio/video equipment. Dolby Pro Logic Surround provides a true center channel, so that there are four independent channels, unlike passive Dolby Surround which has in effect only three channels: left, right, and rear. This center channel allows listeners seated in even less-than-ideal positions to hear the dialog originating from action on the screen while getting a stereo effect as well. This Dolby Pro Logic Surround Decoder employs a digital signal processing system. This system increases sound stability at each channel and minimizes crosstalk between channels compared to conventional analog Dolby signal processing. In addition, this unit features a built-in automatic input balance control. This circuit always presents you the best surround conditions without performing manual adjustments. Dolby Pro Logic Surround + DSP You can also enjoy Dolby Pro Logic with two modes of Digital Sound field processing. These combinations expand the surround effect. One is the “ENHANCED” Dolby Pro Logic Surround which recreates the surround effect of the 35 mm film movie theater. The other is the sound field program ”70 mm MOVIE THEATER”. Which recreates the listening experience of a 70 mm film theater. Directional Enhancement Circuit + DSP The newly featured directional enhancement circuit expands and focuses the digital sound field by emphasizing position of sound. This effect puts you in the midst of the action, while centering and focusing your attention to the screen. This circuit is available on the sound field program “TV THEATER” and “SPORTS”. 6 CINEMA DSP The YAMAHA “CINEMA DSP” logo indicates these programs are created by the combination of Dolby Pro Logic and YAMAHA DSP technology. SPEAKER SETUP FOR THIS UNIT SPEAKERS TO BE USED This unit is designed to provide the best sound-field quality with a seven speaker configuration. The speakers to be used with this unit will be main speakers, front speakers, rear speakers, and a center speaker. The main speakers are used for the main source sound. These are usually a much larger, high-quality loudspeaker than you will use for the surround sound effects. The center speaker is used for the center sound (dialog, etc.) encoded with the Dolby Surround. And the front and rear speakers are used for special effects that enhance the surround sound. The front, rear, and center speakers do not need to be equal to the main speakers. However, all the speakers should have high enough power handling to accept the maximum output of this unit. SPEAKER CONFIGURATION Seven-Speaker Configuration This configuration is the most effective and recommended one. In this configuration, the front speakers and the center speaker are necessary along with the rear speakers. If the digital sound field program DOLBY PRO LOGIC, DOLBY PRO LOGIC ENHANCED, 70 mm MOVIE THEATER, TV THEATER, or SPORTS is selected, conversations will be output from the center speaker and the ambience will be excellent. • The FRONT MIX switch on the rear panel should be set to the “7 ch” setting. (For details, refer to page 17.) • Set the center channel mode to the “NORMAL” or “WIDE” position. (For details, refer to page 17.) Five-Speaker Configuration When you only have five speakers, this configuration can be very effective. In this configuration, the center speaker is used for dialog when you select the digital sound field program DOLBY PRO LOGIC, DOLBY PRO LOGIC ENHANCED, 70 mm MOVIE THEATER, TV THEATER, or SPORTS. The front speakers are not used. The main speakers handle the front channel effects. • The FRONT MIX switch should be set to the “5 ch” setting. (For details, refer to page 17.) • Set the center channel mode to the “NORMAL” or “WIDE” position. (For details, refer to page 17.) Main L Center Main R Front L Front R Dialogue Surround sound Rear R Rear L Main L Center Main R Dialogue Surround sound Rear L Rear R Main L Main R Four-Speaker Configuration The center speaker is not used in this configuration. If the digital sound field program DOLBY PRO LOGIC or DOLBY PRO LOGIC ENHANCED is selected, the center sound along with the front effects are output from the left and the right main speakers. However, the sound effect of other programs can be the same as that of the other configurations. • Be sure to set the center channel mode to the “PHANTOM” position. (For details, refer to page 17.) Dialogue Surround sound Rear L Rear R 7 SPEAKER PLACEMENT The recommended speaker configuration, the seven-speaker configuration, will require three speaker pairs: main speakers, front speakers, and rear speakers, plus a center speaker. When you place these speakers, refer to the following: Front L Main L Main R Center Rear R Rear L 8 In normal position. (The position of a standard stereo speaker setup) Front: Placed much further apart than the Main speakers, facing slightly inwards. Nearly six feet (approx. 1.8 m) up from the floor. Center: Precisely between the main speakers. (To avoid interference with TV sets, use a magnetically shielded speaker.) When two center speakers are used, place these to the right and left of your TV set or video monitor. Rear: Behind your listening position, facing slightly inward. Nearly six feet (approx. 1.8 m) up from the floor. Main: Front R CONNECTIONS CAUTION Before attempting to make any connections to or from this unit, be sure to first switch OFF the power to this unit and to any other components to which connections are being made. CONNECTIONS WITH OTHER COMPONENTS When making connections between this unit and other components, be sure all connections are made correctly, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Also, refer to the owner’s manual for each component to be connected to this unit. Turntable Video cassette recorder 1 GND AUDIO OUT AUDIO IN VIDEO OUT VIDEO IN OUTPUT Compact disc player Video cassette recorder 2 AUDIO SIGNAL VIDEO SIGNAL AUDIO SIGNAL S VIDEO VIDEO Tape deck 1 PHONO LINE OUT GND LINE OUT FM ANT 75Ω UNBAL. Tape deck 2 VCR 1 VCR 1 OUT OUT TAPE PB IN IN TAPE 1 VCR 2 VCR 2 REC OUT OUT OUT TAPE PB LD/TV LD/TV LD/TV MAIN MONITOR OUT LD/TV CENTER FRONT MIX AUDIO OUT VIDEO OUT VIDEO IN AUDIO IN TAPE 2 REC OUT GND 5CH DISCRT INPUT MAIN IN ON 5ch OFF 7ch MAIN CH PRE OUT MAIN LEVEL VIDEO IN LD/TV SURROUND 0dB AUDIO PRE OUT -10dB VIDEO OUT ROOM 2 OUT IN OUT Monitor TV REMOTE CONTROL VIDEO OUT LINE IN IN CD AUDIO OUT LINE IN AM ANT IN LaserDisc-Spieler 9 CONNECTING SPEAKERS Connect the respective speakers to this unit as shown below: Front speakers Main speakers A Right Right Left Rear speakers Left Right Left SPEAKERS FRONT REAR OUTPUT FRONT OUT LOW PASS CENTER OUT REAR OUT fo:200Hz 8ΩMIN. /SPEAKER 8ΩMIN. /SPEAKER CENTER A B C D D C C+D A OR B: 5ΩMIN. /SPEAKER A + B:l2ΩMIN. /SPEAKER Right C C: 8ΩMIN. /SPEAKER C+ D: 4ΩMIN. /SPEAKER Left Center speaker(s) Main speakers B Note on main speaker connection: One or two speaker systems can be connected to this unit. If you connect only one speaker system, connect it to either the SPEAKERS A or B terminals. Note: Use speakers with the specified impedance shown on the rear of this unit. For connecting to the SPEAKER terminals Note on center speaker connection: One or two center speakers can be connected to this unit. If you cannot place the center speaker on or under the TV, it is recommended to use two center speakers and place them on both sides of the TV to orient the center sound at the center position. When connecting two center speakers, be sure to press the CENTER speaker switch into the “C+D” position ( ) . When you use a single center speaker, set the switch to the “C” position( ) . Red: positive (+) Black: negative (–) How to Connect: Connect the SPEAKERS terminals to your speakers with wire of the proper gauge, cut as short as possible. If the connections are faulty, no sound will be heard from the speakers. Make sure that the polarity of the speaker wires is correct, that is, + and – markings are observed. If these wires are reversed, the sound will be unnatural and will lack bass. Banana Plug connections are also possible. Simply insert the Banana Plug connector into the corresponding terminal. (Not available on Singapore model.) CAUTION Do not let the bare speaker wires touch each other and do not let them touch the metal parts of this unit. This could damage this unit and/or the speakers. 10 2 1 3 1 Unscrew the knob. 2 Insert the bare wire. [Remove approx. 5mm (1/4") insulation from the speaker wires.] 3 Tighten the knob and secure the wire. Note: Use only single type banana plug cable. ABOUT THE ACCESSORY TERMINALS OUTPUT FRONT OUT LOW PASS 3 CENTER OUT 4 1 REAR OUT fo:200Hz 2 1 LOW PASS terminal This terminal is for output to a monaural amplifier driving a subwoofer. Frequencies above 200␣ Hz are filtered out so that only the bass range remains. The output signal is from the main and center channels. You may wish to add a subwoofer to reinforce the bass frequencies. Connect the LOW PASS terminal to the INPUT terminal of the subwoofer amplifier, and connect the speaker terminals of the subwoofer amplifier to the subwoofer. With some subwoofers, including the Yamaha Active Servo Processing Subwoofer System, the amplifier and subwoofer are in the same unit. 2 CENTER OUTPUT terminal This terminal is for center channel line output. There is no connection to this terminal when you use the built-in amplifier. However, if you drive a center speaker with an external power amplifier, connect the input terminal of the external amplifier to this terminal. 3 FRONT OUTPUT terminals These terminals are for front channel line output. There is no connection to these terminals when you use the built-in amplifier. However, if you drive front speakers with an external stereo power amplifier, connect the input terminals of the external amplifier (MAIN IN or AUX terminals of a power amplifier or an integrated amplifier) to these terminals. 4 REAR OUTPUT terminals These terminals are for rear channel line output. There is no connection to these terminals when you use the built-in amplifier. However, if you drive rear speakers with an external stereo power amplifier, connect the input terminals of the external amplifier (MAIN IN or AUX terminals of a power amplifier or an integrated amplifier) to these terminals. GND terminal (For turntable use) Connecting the ground wire of the turntable to this terminal will normally minimize hum. In some cases, better results may be obtained with the ground wire disconnected. GND AC OUTLETS 2 SWITCHED OUTLETS and 1 UNSWITCHED OUTLET (USA, Canada, and General models) 1 SWITCHED OUTLET (Australia model) 2 SWITCHED OUTLETS (Singapore model) SWITCHED UNSWITCHED 120V 60Hz 120W MAX. TOTAL 120V 60Hz 200W MAX. (USA model) Use these to connect the power cords from your components to this unit. The power to the SWITCHED outlets is controlled by this unit’s POWER switch or the provided remote control transmitter’s POWER key. These outlets will supply power to any connected component whenever this unit is turned on. The maximum power (total power consumption of components) that can be connected to the SWITCHED AC OUTLET(S) is 120 watts. The power to the UNSWITCHED outlets cannot be controlled by this unit’s POWER switch or the provided remote control transmitter’s POWER key. (USA, Canada, and General models only). The maximum power (power consumption of component) that can be connected to the UNSWITCHED AC OUTLET is 200 watts (USA model), 180 watts (Canada model) and 200 watts (General model). 11 A TAPE 2 REC OUT 5 5CH DISCRT INPUT MAIN IN LD/TV MAIN MONITOR OUT LD/TV CENTER FRONT MIX ON 5ch OFF 7ch 0 MAIN CH 6 PRE OUT 7 MAIN LEVEL 9 LD/TV SURROUND 0dB AUDIO PRE OUT -10dB VIDEO OUT ROOM 2 OUT IN OUT REMOTE CONTROL 8 5 MAIN␣ CH — MAIN␣ IN terminals These terminals are for line input to the built-in main channel amplifier. Leave the jumper bars connected to the PRE␣ OUT terminals when you use the built-in amplifier. However, if you drive main speakers with an external stereo power amplifier, remove the jumper bars. 6 MAIN␣ CH — PRE␣ OUT terminals These terminals are for main channel line output. Leave the jumper bars connected to the MAIN␣ IN terminals when you use the built-in amplifier. However, if you drive main speakers with an external stereo power amplifier, remove the jumper bars and connect the input terminals of the external amplifier (MAIN IN or AUX terminals of a power amplifier or an integrated amplifier) to these terminals. 7 MAIN LEVEL switch Normally set to “0␣ dB”. If desired, you can decrease the output level at the MAIN SPEAKERS terminals by 10␣ dB by setting this switch to “–10␣ dB”. 8 ROOM 2 OUT — AUDIO PRE OUT, VIDEO OUT terminals These terminals output audio and video signals to the equipment in the second room. The signal source is selected using the Room 2 Remote transmitter. Refer to “Connecting to Room 2 Equipment” on page 14. 12 9REMOTE CONTROL — IN, OUT terminals IN This terminal receives the commands from the Room 2 Remote transmitter. OUT This terminal outputs the commands at the IN terminal from Room 2 Remote transmitter. Refer to “Connecting to Room 2 Equipment” on page 14. 0 FRONT MIX switch This switch should be set to match the number of speakers in your system. For seven speaker configurations, set it to “7 ch”. For five speaker configurations, set it to “5 ch”. A 5CH DISCRT INPUT terminals These terminals are used with a Dolby Surround AC-3 decoder. Connect the main audio output of the decoder to the LD/TV MAIN input terminals, the center channel audio output to the LD/TV CENTER input terminal, and the surround audio output to the LD/TV SURROUND input terminals. Note: 5CH DISCRT INPUT terminals can only be used with an AC-3 decoder. When you use a Dolby Surround AC-3 decoder, the LFE (Low Frequency Effect channel) signal coming from the AC-3 decoder to this unit must be mixed with the main output signal. Refer to your AC-3 decoder’s operating manual for information about mixing these signals mode. CONNECTING S␣ VIDEO TERMINALS If your video cassette recorder, video disc player, monitor, etc., is equipped with “S” (high-resolution) video terminals, connect them to this unit’s S␣ VIDEO terminals. Otherwise, use the composite video terminals of the unit. Note: • If video signals are sent to both the S␣ VIDEO input and composite input terminals, the input signals will be sent to the respective S␣ VIDEO output and composite output terminals independently. VIDEO SIGNAL VIDEO S VIDEO IN OUT VIDEO OUT VIDEO IN VCR 2 VIDEO IN S VIDEO IN IN S VIDEO IN S VIDEO OUT VIDEO OUT OUT S VIDEO OUT VCR 1 LD/TV Video Cassette recorder 1 MONITOR OUT Video Cassette recorder 2 VIDEO IN S VIDEO IN S VIDEO OUT VIDEO OUT LD player Monitor TV ON SCREEN DISPLAY If you connect a video cassette recorder, video disc player, monitor, etc., to this unit, you can display DSP program names and information about the other settings and adjustments on the video monitor screen which is connected to MONITOR OUT terminal (cannot display on ROOM 2 moinitor). This information is superimposed over the video image. If there is no program material on the monitor, the information will be displayed over a monochromatic background. Notes: • If you use a video monitor that is connected to both the S␣ VIDEO and composite terminals, the screen display information is only output from the S␣ VIDEO terminals. • When no video signal is input to any of the S␣ VIDEO or composite video input terminals, the screen display information is output from the S␣ VIDEO and composite MONITOR OUT terminals with a monochromatic background. CONNECTING TO VIDEO AUX TERMINALS (FRONT PANEL) These terminals are used to connect any video input source such as a camcorder to this unit. VIDEO AUX 8 VIDEO VIDEO L AUDIO R AUDIO OUT AUDIO OUT VIDEO OUT R 8 VIDEO VIDEO S-VIDEO L Camcorder S VIDEO OUT 13 CONNECTING TO ROOM 2 EQUIPMENT With the Room 2 Remote transmitter you can select a different sound and video source for a second room. To use the multi-room functions of this unit you need the following additional,optional products: • An infrared signal receiver for the second room. (WCX-10) • Master Zone Controller (MCX-10) • An infrared emitter in the main room. (IRX-10/20) This emitter transmits the infrared signals from the Room 2 Remote transmitter in the second room to the other components in the main rooms (for example, the remote for your laserdisc player). • An amplifier and speakers for the second room. • A video monitor for the second room. Note Since there are so many ways to connect and use your RX-V2090 in a multi-room installation, we recommend that you consult with a custom installation specialist for the Room 2 connections which will best meet your requirements. Sample Room 2 connections: Main Room Second Room Amplifier Video monitor Cassette deck, etc Room 2 Remote * REMOTE CONTROL IN ROOM 2 VIDEO OUT ROOM2 AUDIO PREOUT RX-V2090 Infrared signal receiver (WCX-10) Infrared emitter (IRX-10/20) Master Zone Controller MCX-10 MCX-10 Yamaha models are able to connect directly to the RX-V2090 via the REMOTE OUT terminals. If you own * Some these products, the use of an infrared emitter may not be necessary. CAUTION In some cases, adjustments made using the Room 2 Remote transmitter may not be evident on this unit. For example, if both the main room and second room are set to the tuner, it is possible for the person in the second room to change the station. This may be a problem, especially when you are taping a source without directly monitoring it. Using the Remote Transmitters If you use the Room 2 Remote transmitter (the transmitter for the second room) in the main room, the input selector keys of this remote affect the settings in the second room, not the main room. The other keys on the transmitter work the same in both the main room and the second room. If you use the Main Remote transmitter (the transmitter for the main room) in the second room, the keys that also appear on the Room 2 Remote transmitter work except the input selector keys. ROOM 2 ROOM 2 CONTROL 14 1 2 The indicator information: 1 Lights up momentarily when the Room 2 Remote transmitter is used in the main room. 2 Lights up momentarily when the Room 2 Remote transmitter is used in the second room. ANTENNA CONNECTIONS • Each antenna should be connected to the designated terminals correctly, referring to the following diagram. • Both AM and FM indoor antennas are included with this unit. In general, these antennas will probably provide sufficient signal strength. Nevertheless, a properly installed outdoor antenna will give clearer reception than an indoor one. If you experience poor reception quality, an outdoor antenna may result in improvement. Outdoor AM antenna Outdoor FM antenna AUDIO SIGNAL AM loop antenna (included) AUDIO PHONO CD TAPE PB AM ANT TAPE 1 300-ohm feeder GND REC OUT FM ANT TAPE PB 75Ω UNBAL. TAPE 2 REC OUT GND 5CH DISCRT INPUT MAIN IN MAIN CH PRE OUT 75-ohm coaxial cable 75-ohm/300-ohm antenna adapter MAIN LEVEL 0dB -10dB Indoor FM antenna (included) Ground Connecting the AM loop antenna 1 2 ➀ ➂ 3 Orient so that the best reception is obtained. ➁ • The AM loop antenna should be placed apart from the main unit. The antenna may be hung on a wall. • The AM loop antenna should be kept connected, even if an outdoor AM antenna is connected to this unit. GND terminal For maximum safety and minimum interference, connect the GND terminal to a good earth ground. A good earth ground is a metal stake driven into moist earth. Notes: • When connecting the indoor FM antenna, insert its connector into the FM ANT terminal firmly. • If you need an outdoor FM antenna to improve FM reception quality, either 300-ohm feeder or coaxial cable may be used. In locations troubled by electrical interference, coaxial cable is preferable. 15 ADJUSTMENT BEFORE OPERATION SPEAKER BALANCE ADJUSTMENT This procedure lets you adjust the sound output level balance between the main, front, center, and rear speakers using the built-in test tone generator. With this adjustment, the sound output level heard at the listening position will be the same from each speaker. This is important for the best performance of the digital sound field processor. The adjustment of each speaker output level should be done at your listening position with the remote control transmitter. Otherwise, the result may not be satisfactory. 1 TRANSMIT USER LEARN /LEARN YPC 6 POWER SLEEP TV VCR SKIP AUX 5 PHONO DISC SKIP SEARCH — REC MUTE 3 4 CD TUNER STOP PLAY TAPE 1 DIR A DIR B TAPE 2 MON PRESET SEARCH 2 PLAY A/B/C/D/E PAUSE/STOP DECK A/B REC/PAUSE + * If you have a video monitor connected to this unit, you should use it to display the on screen information. The easy-to-read information will help you to perform this adjustment. Note: Before adjustment, make sure that the mute circuit is not engaged. While mute is engaged, no sound will be heard and an indicator on the master VOLUME control flashes. See page 21 for details. 1 4 Set to the “∞” position. VOLUME l8 l6 l4 20 l2 24 USER YPC LEARN l0 28 8 34 6 4 40 3 50 2 60 For detailed information about the remote control transmitter, refer to “REMOTE CONTROL TRANSMITTER” on page 32. l 70 0 –dB 2 5 Set to the “0” position. BASS l 0 2 2 l 2 3 4 3 4 5 4 5 5 6 Set to the “0” position. BALANCE l 0 Select the main speakers to be used. SPEAKERS A B l 2 2 3 3 4 4 L 5 16 0 2 3 4 3 l POWER Press the POWER switch to turn on the power. TREBLE l 3 5 Set the remote YPC-USER-LEARN switch to the “YPC” position. 5 R • If you use two main speaker systems, press both the A and B switches. 7 CHAPTER/CH DISPLAY STOP VCR 1 — + PRO LOGIC ENHANCED 70mm MOVIE THEATER TV THEATER VCR 2 2 3 4 JAZZ CLUB 1 SURROUND STADIUM ROCK 5 6 7 CHURCH SPORTS HALL 9 10 V–AUX 8 EFFECT DSP ON/OFF MASTER VOLUME FRONT LEVEL — + + + + RESET CLEAR 9 DELAY TIME REAR LEVEL — + TEST CENTER LEVEL — MUTING — — 8 7 Select the center channel output mode according to your speaker configuration. (Refer to “SPEAKER CONFIGURATION” on page 7.) Press the TEST button again to run the DSP test. • DSP test: CENTER MODE NORMAL WIDE PHANTOM 8 9 TEST Press the TEST button to run the Dolby test. Turn up the volume using the remote control transmitter. You will hear a test tone (like pink noise) from the left main speaker, then the center speaker, then the right main speaker, and then the rear speakers, for about two seconds each. The display changes as shown below. There are two types of tests: Dolby test and DSP test. • Dolby test: The test tone from the left main speaker and the right main speaker, the left front and the right front speaker will be heard at the same time. To adjust the FRONT LEVEL, go to step 13. Note: When the FRONT MIX switch is set to “5ch” (5 channel mode) the DSP test mode is not available. • If your video monitor is on, the state of the test tone output is also shown by an image of an audio listening room on the screen. In step 7, when you select the center mode, note the following. Seven and five speaker configuration NORMAL: * * The test tone from the left rear speaker and the right rear speaker will be heard at the same time. To adjust the BALANCE, CENTER LEVEL and the REAR LEVEL, go to steps 10~12. WIDE: Select this mode when you use a center speaker that is smaller than the main speakers. In this mode, the bass tone will be output from the front main speakers. Select this mode when your center speakers are approximately the same size as the main speakers. Note: For seven speaker configurations, the FRONT MIX switch on the rear panel should be set to the “7 ch” setting. For five speaker configurations, the FRONT MIX switch should be set to the “5 ch” setting. Six and Four speaker configuration PHANTOM: Select this mode when you do not have a center speaker. The center channel sound will be output from the left and right main speakers. 17 13 CHAPTER/CH DISPLAY STOP VCR 1 — + PRO LOGIC ENHANCED 70mm MOVIE THEATER TV THEATER VCR 2 2 3 4 JAZZ CLUB 1 SURROUND SPORTS 13 11 11 STADIUM ROCK 5 6 7 CHURCH HALL 9 10 DSP — + + MASTER VOLUME + — + RESET CLEAR + TEST CENTER LEVEL — DELAY TIME MUTING — — 14 10 12 the BALANCE control so that the test tone sound 10 Adjust output level of the left front speaker and the right front ON/OFF FRONT LEVEL REAR LEVEL 12 V–AUX 8 EFFECT the test tone sound output level of the front 13 Adjust speakers to be at the same level as that of the main speakers with the FRONT LEVEL keys. (DSP test) speaker are the same. BALANCE l 0 LEVEL FRONT l 2 2 3 3 4 4 L 5 5 R the test tone sound output level of the center 11 Adjust speaker to be at the same level as that of the main speakers with the CENTER LEVEL keys. (Dolby test) 14 Cancel the test tone. LEVEL CENTER TEST PRO LOGIC The previous mode is selected. the sound output level of the rear speakers to be 12 Adjust at the same level as that of the main speakers with the REAR LEVEL keys. (Dolby test) LEVEL REAR Notes: • If the center channel mode is in the “PHANTOM” position, the sound output level of the center speaker cannot be adjusted. This is because in this mode, the center sound is automatically output from the left and right front speakers. • When the FRONT MIX switch is set to 5ch, front level adjustment cannot be executed from the front panel or from the REMOTE CONTROL TRANSMITTER. • You cannot adjust the front level when the LD/TV switch is set to 5CH DISCRT mode. • If you press the LEVEL +/– switch without previously pressing the FRONT, CENTER, or REAR switch, the last channel selected will be changed. 18 Notes: • Once you have completed these adjustments, you can adjust whole sound level on your audio system by using the VOLUME control (or the MASTER VOLUME keys on the remote control transmitter). • If you use external power amplifiers, their volume controls may also need to be adjusted to achieve the proper balance. If there is insufficient sound output from the center and rear speakers, you may decrease the main speaker output level by setting the MAIN LEVEL switch on the rear panel to “–10 dB”. BASIC OPERATIONS 2 3 1,6 4 To play a source 1 5 Set to the “∞” position. VOLUME l8 l6 Play the source. (For detailed information on the tuning operation, refer to page 22.) l4 20 l2 24 l0 28 6 8 34 6 Adjust to the desired output level. 4 40 VOLUME 3 50 l8 l4 l2 24 l 70 l6 20 2 60 l0 28 0 –dB 8 34 6 4 40 2 3 50 POWER Press the POWER switch to turn on the power. 2 60 l 70 0 –dB 3 If desired, adjust the BASS, TREBLE, BALANCE controls, etc. (refer to page 21) and use the digital sound field processor. (Refer to page 26.) Select the desired input source by using the input selector buttons. (For video sources, turn the video monitor ON.) TAPE 2 MONITOR TAPE 1 VIDEO AUX TUNER VCR 2 CD VCR 1 PHONO LD/TV • The name of the selected input source will appear on the display. 4 Select the main speakers to be used. SPEAKERS A B • If you use two main speaker systems, press both the A and B switches. Notes on using the input selector buttons • Note that pressing on each input selector button selects the source which is connected to the corresponding input terminals on the rear panel. • To select the source connected to the VIDEO AUX terminals on the front panel, press VIDEO AUX. • The selection of TAPE 2 MONITOR cannot be canceled by pressing another input selector button. To cancel it, press TAPE 2 MONITOR again. When you select a button other than TAPE 2 MONITOR, make sure that TAPE 2 MONITOR is not accidently selected as well. • If you select the input selector button for a video source without canceling the selection of TAPE 2 MONITOR, the playback result will be the video image from the video source and the sound from the audio tape. • Once you play a video source, its video image will not be interrupted even if the input selector button for an audio source is selected. • For the LD/TV input selector button, refer to page 28. To turn off the power Press the POWER switch again. 19 2 1 To record a source to tape (or dub from tape to tape) 1 Select the source to be recorded. REC OUT SOURCE LD/TV TAPE 1 VCR 1 TUNER CD VCR 2 PHONO VIDEO AUX 2 Play the source and press the corresponding input selector, then turn the VOLUME control up to confirm the input source. (For detailed information on the tuning operations, refer to page 22.) VOLUME TAPE 2 MONITOR TAPE 1 l8 TUNER CD l6 20 PHONO l4 l2 24 l0 28 8 34 VIDEO AUX VCR 2 VCR 1 6 LD/TV 4 40 3 50 2 60 l 70 0 –dB 3 4 20 Set the tape deck or VCR to the recording mode. To monitor a source selected by the REC OUT selector, press the corresponding input selector button. Notes: • When the REC OUT selector is set to “SOURCE”, the source selected by the input selector buttons is output through the TAPE 1-REC OUT, the TAPE 2-REC OUT , the VCR 1-OUT, and the VCR 2-OUT terminals. • When the REC OUT selector is set to something other than “SOURCE” and you press an input selector button other than the one you pressed in step 2, the recording source will not be changed and you can enjoy another source while recording. • To record from tape deck 2, set the REC OUT selector to SOURCE, and press the TAPE 2/MONITOR input selector. • If the tape deck connected to the TAPE 2 REC OUT terminal has 3-head monitoring capability, you can monitor the signal just recorded on the tape by pressing the TAPE 2/MONITOR switch. • DSP, VOLUME, BASS, TREBLE and BALANCE control settings have no effect on the material being recorded. • Signals connected to the 5CH DISCRT INPUT are not output to the tape decks or video recorders. To record the signals from an LD player, you must connect the player to the LD/TV terminals. • It is possible for someone in the second room to use the Room 2 Remote transmitter to change the source you selected for recording. For example, if you are recording a program from the tuner and the person in the second room changes the station. If you are listening to another source, you may not discover this error until you playback the recording. Selecting the SPEAKERS system Using the TONE BYPASS switch Because one or two speaker systems (as main speakers) can be connected to this unit, the SPEAKERS switches allow you to select speaker system A or B, or both at once. Press this switch to revert instantly to the flat states of the BASS and TREBLE controls without changing the setting of these controls. TONE BYPASS SPEAKERS A B ON OFF Using the BASS EXTENSION switch Adjusting the BALANCE control Adjust the balance of the output volume to the left and right speakers to compensate for sound imbalance caused by speaker location or listening room conditions. You can boost bass frequency response by setting this switch to the “ON” position. This switch is effective only on the sound from the main speakers. BASS EXTENSION BALANCE l 0 ON l 2 2 OFF 3 3 4 4 L 5 MUTING Key (Main Room remote transmitter) 5 R Note: This control is effective only for the sound the main speakers. Adjusting the BASS and TREBLE controls BASS Turn this clockwise to increase (or counter-clockwise to decrease) the low frequency response. TREBLE Turn this clockwise to increase (or counter-clockwise to decrease) the high frequency response. Press this key to mute the master volume. While mute is engaged, an indicator on the master VOLUME control flashes. Press again to un-mute the master volume. MUTING VOLUME SPORTS STADIUM ROCK JAZZ CLUB 5 6 7 8 V–AUX l8 l6 20 l4 l2 24 CHURCH 9 HALL 10 EFFECT DSP ON/OFF MASTER VOLUME Flash l0 28 8 34 6 FRONT LEVEL — + + — + DELAY TIME REAR LEVEL — + 2 60 l 70 MUTING — 3 50 TEST CENTER LEVEL 4 40 + — 0 –dB BASS l 0 TREBLE l 2 l 2 3 3 4 4 5 5 0 RESET CLEAR l 2 2 3 3 4 4 5 5 Note: These controls are effective only for the sound from the main speakers. When you listen with headphones PHONES Connect the headphones to the PHONES jack. You can listen to the sound to be output from the main speakers through headphones. When listening with headphones privately, set both the SPEAKERS A and B switches to the OFF position and switch off the digital sound field processor (so that the message “EFFECT OFF” is shown on the display) by pressing the EFFECT switch. 21 TUNING OPERATIONS Normally, if station signals are strong and there is no interference, quick automatic-search tuning (AUTOMATIC TUNING) is possible. However, if signals of the station you want to select are weak, you must tune to it manually (MANUAL TUNING). 1, 2, 3,4, AUTOMATIC TUNING 1 MANUAL TUNING Select the reception band (FM or AM) while watching the display. FM/AM FM/AM or AM 2 Select the reception band (FM or AM) while watching the display. FM TUNING MODE AM or FM TUNING MODE AUTO TUNING 3 DOWN TUNING “AUTO TUNING” goes off. UP Tune to a desired station manually. DOWN TUNING UP To tune to a higher frequency, press the right side once. To tune to a lower frequency, press the left side once. • To continue tuning search, press and hold the button. 4 If the station where tuning search stops is not the desired one, press again. DOWN TUNING UP Note: If you tune to an FM station manually, it is received in monaural mode automatically to increase the signal quality. • If the tuning search does not stop at the desired station (because the signals of the station are weak), change to the MANUAL TUNING method. Display information 1 AM FM 2 kHz MHz STEREO 0 22 20 40 60 3 l00 1 Displays the band and frequency of the received station. 2 Lights up when an FM stereo broadcast is received in stereo. 3 Indicates the signal level of the received station. PRESET TUNING Manual Preset Tuning This unit can store station frequencies (selected by tuning operation) by using the preset station buttons. With this function, you can select any desired station by only pressing the corresponding preset station button. Up to 40 stations (8 stations × 5 pages) can be stored. 2, 4, 3 To program stations 1 2 To recall a preset station Tune to a desired station. (Refer to the previous page for tuning procedure.) Select the page of preset station buttons. A/B/C/D/E PRESET Select a desired page (A - E) of preset station buttons while watching the display. A/B/C/D/E PRESET FM Select the desired preset station button. MHz I 3 2 3 PRESET STATIONS 4 5 6 7 8 PRESET MEMORY FM PRESET FM MHz MEMORY Flashes for about 5 seconds. 4 Press a preset station button before the “MEMORY” prompt on the display switches off. I 2 3 PRESET STATIONS 4 5 6 7 8 PRESET FM Shows the displayed station has been programmed to A1. Notes: • A new setting can be programmed in place of the former one. • For presets, the setting of the reception mode (stereo or monaural) is stored along with the station frequency. Memory back-up The memory back-up circuit prevents the programmed data from being lost even if the POWER switch is set off or the power plug is disconnected from the AC outlet or the power is cut due to temporary power failure. If, however, the power is cut for more than one week, the memory may be erased. If so, it can be re-programmed by simply following the PRESET TUNING steps. • In the same way, program other stations to A2, A3, to A8. • You can program more stations to the preset station buttons on other pages in the same way by selecting other pages in step 2. 23 Automatic Preset Tuning You can also make use of an automatic preset tuning function for FM stations only. By this function, this unit performs automatic tuning and stores FM stations with strong signals sequentially. Up to 40 stations are stored automatically in the same way as in the manual preset tuning method on page 23. 2 3 1 To program stations 1 If you want to store the first station received by the automatic preset tuning to a desired preset station number. If, for example, you want to store the first received station to C5, select “C5” by using the A/B/C/D/E button and the preset station buttons after pressing the MEMORY button in step 2. Then press the TUNING button. The first received station is stored to C5, and next stations to C6, C7, etc., sequentially. If stations are stored up to E8, the automatic preset tuning is finished automatically. FM/AM FM 2 MEMORY PRESET FM MHz STEREO MEMORY 0 20 40 60 l00 Press and hold for about 3 seconds. Flashes 3 DOWN TUNING UP To tune to higher frequencies, press right side once. To tune to lower frequencies, press left side once. • If the TUNING button is not pressed, in a while the automatic preset tuning begins automatically toward higher frequencies. The automatic preset tuning begins from the frequency currently displayed. Received stations are programmed to A1, A2, to A8 sequentially. • If more than 8 stations are received, they are also programmed to the preset station numbers on other pages (B, C, D and E) in that order. 24 When the automatic preset tuning is finished The display shows the frequency of the last preset station. Check the contents and the number of preset stations by following the procedure of the section “To recall a preset station” on page 23. To recall a preset station Simply follow the procedure of the section “To recall a preset station” on page 23. Notes: • You can replace a preset station by another FM or AM station manually by simply following the procedure of the section “To program stations” on page 23. • If the number of received stations is not enough to be stored up to E8, the search is finished automatically when it reaches the highest frequency after searching through all frequencies. • With this function, only FM stations with sufficient signal strength are stored automatically. If the station you want to program is weak in signal strength, tune to it in monaural manually and program it by following the procedure of the section “To program stations” on page 23. Exchanging Preset Stations You can exchange the places of two preset stations with each other as shown below. 2,4 (Example) If you want to shift the preset station on E1 to A5, and vice versa. 1 2 Recall the preset station on E1 (by following the method of “To recall a preset station” on page 23). EDIT MEMORY 3 Next, recall the preset station on A5 by following the procedure in step 1. MEMORY 4 EDIT Shows the exchange of stations is completed. MEMORY 25 USING THE DIGITAL SOUND FIELD PROCESSOR (DSP) This unit incorporates a sophisticated, multi-program digital sound field processor, which allows you to expand and shape the audio sound field from both the audio and video sources, for a theater-like experience in the listening/viewing room. This digital sound field processor has 10 programs; 8 programs for digital sound field processing and 2 programs for the Dolby Pro Logic Surround sound system (DOLBY PRO LOGIC and DOLBY PRO LOGIC ENHANCED). You can create an excellent audio sound field by selecting the suitable program and adding desired adjustments. In addition, when the DOLBY PRO LOGIC, DOLBY PRO LOGIC ENHANCED, or 70␣ mm MOVIE THEATER program is selected, the built-in automatic input balance control functions. This presents you the best surround condition without manual adjustment. 1 2 CINEMA DSP 2090 7ch TAPE 2 MONITOR TAPE 1 VIDEO AUX TUNER VCR 2 CD PHONO VCR 1 LD/TV PRO LOGIC WIDE CHURCH HALL 9 10 EFFECT DSP ON/OFF 2CH/5CH DISCRT PRESET STATIONS 4 5 3 6 7 TV 70mm PRO LOGIC ENHANCED MOVIE THEATER THEATER 8 — SPORTS + + TEST CENTER LEVEL BASS 0 FRONT CENTER REAR TREBLE l l 2 3 4 ROCK CONCERT JAZZ CLUB CHURCH LEVEL DELAY TIME 0 BALANCE l 2 l 2 3 3 4 5 3 2 3 4 5 4 L 5 4 REC OUT VCR 1 VCR 2 VIDEO AUX EFFECT — + RESET CLEAR VIDEO AUX SOURCE LD/TV TAPE 1 l 3 4 5 0 2 + 8 VIDEO VIDEO L AUDIO R TUNER CD PHONO 5 R 5 6 1 CENTER MODE Selects the center channel output mode. (For details, refer to page 17.) 2 Displays your selection on the DSP or other informations. 3 DELAY TIME –/+ Adjusts the delay time. (For details, refer to page 30.) 4 CENTER and LEVEL –/+ FRONT and LEVEL –/+ REAR and LEVEL –/+ Adjusts sound output level at each speaker. (For details, refer to page 29.) 5 Selects a digital sound field program. 6 EFFECT Switches on/off the digital sound field processor (DSP). 7 TEST Used for speaker balance adjustment. (For details, refer to page 17.) 26 DELAY TIME REAR LEVEL CONCERT HALL + STADIUM — CENTER MODE MASTER VOLUME FRONT LEVEL DIGITAL SOUND FIELD PROCESSOR MUTING — — 7 Description of Each Sound Field Program The following list gives brief descriptions of the sound fields produced by each of the DSP programs. Keep in mind that most of these are precise digital recreations of actual acoustic environments. The data for them was recorded at the locations described using sophisticated sound field measurement equipment. Note: The channel level balance between the left rear effect speaker and the right rear effect speaker may vary depending on the sound field you are listening to. This is due to the fact that most of these sound field recreations are actual acoustic environments. PROGRAM PRO LOGIC FEATURE This program is effective for playback of sources encoded with Dolby Surround. The employment of the digital signal processing system reduces crosstalk and transfers the sound source more smoothly and precisely, compared to conventional types. A stable movie sound field is recreated. PRO LOGIC ENHANCED This program is effective for playback of sources encoded with Dolby Surround. Enhancing the “Normal” Dolby Pro Logic, the DSP technology simulates the multi-surround speaker systems of a 35 mm film theater, thus widening the surround-sound field with greater presence. 70 mm MOVIE THEATER This program is effective for playback of sources encoded with Dolby Surround. The Yamaha DSP technology is ideally combined with the Dolby Pro Logic to present you the incredible listening experience of the 70 mm movie theater. This program is ideal for precisely reproducing the sound design of the newest movies. The sound field is made according to the design of the latest movie theaters, so the reverberations of the sound field itself are restrained as much as possible. The three-dimensional feeling of the sound field is emphasized and dialog is precisely oriented on the screen. You can enjoy watching sciencefiction, action, and adventure movies with this program. TV THEATER This program is suitable for dramas, variety or music programs, etc. Much surround effect can be gained for stereo sources. SPORTS This program is furnished with a tight sound field in which the sound will not spread excessively on the front side, but the rear surround produces a dynamic sound expansion. This program is most suitable for sports programs encoded with Dolby Surround STADIUM This program gives you long delays between direct sounds and effect sounds, and the extraordinarily spacious feel of a large stadium. ROCK CONCERT This program is suitable for rock music. A big, powerful sound is reproduced lively and dynamically. JAZZ CLUB This is a small, cosy jazz club with a low ceiling. The sound is very close and intimate. CHURCH This program recreates the acoustic environment of a modern church with a high pointed dome and columns along the sides. This interior produces very few primary reflections. CONCERT HALL In this program, the center seems deep behind the front speaker pair, creating an expansive, large hall ambience. Description of Dolby Pro Logic Surround DOLBY PRO LOGIC SURROUND: This unit employs the Dolby Pro Logic Surround system. This system is similar to professional Dolby Stereo decoders used in movie theaters. By employing a four-channel system, the Dolby Pro Logic Surround system divides the input signals into four levels: the left and right main channels, the center channel (to characterize dialog), and the rear surround-sound channels (to characterize sound effects, background noise and other ambient noise). Dolby Surround is encoded on the sound track of commercially available video cassettes and video discs as well. When you play a source encoded with Dolby Surround on your home video system, the Dolby Pro Logic Surround system in this unit decodes the signal and feeds the surround-sound effects. The Dolby Pro Logic Surround mode may not be always effective on video sources not encoded with Dolby Surround. Manufactured under license from Dolby Laboratories Licensing Corporation. Additionally licensed under Canadian patent number 1,037,877. “Dolby”, “AC-3”, “Pro Logic”, and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation. 27 To play a source with the digital sound field processor 2 3 1 2 Follow steps 1 - 6 shown in “BASIC OPERATIONS” on page 19. Select the desired program that is suitable for the source. DIGITAL SOUND FIELD PROCESSOR 70mm TV PRO LOGIC ENHANCED MOVIE THEATER THEATER ROCK CONCERT JAZZ CLUB CHURCH SPORTS STADIUM CONCERT HALL PRO LOGIC The selected program name is shown on the display. 3 Notes: • If you prefer to cancel the DSP, press the EFFECT switch. The sound will be the normal 2-channel stereo without surround sound effect. • When STADIUM, ROCK CONCERT, JAZZ CLUB, CHURCH, or CONCERT HALL is selected, no sound is heard from the center speaker. • When a monaural sound source is played with DOLBY PRO LOGIC or DOLBY PRO LOGIC ENHANCED, no sound is heard from the main speakers, the front speakers, and the rear speakers. Sound is heard only from the center speaker. However, if the center channel mode is in PHANTOM, the main speakers output the sound of the center channel. • When this unit’s Dolby Pro Logic Surround system is used, if the main-source sound is considerably altered by over adjustment of the BASS or TREBLE controls, the relationship between the center and rear channels may produce an unnatural effect. If desired, adjust the delay time and the output level of each speaker. (For details, refer to the corresponding descriptions on page 29, 30.) Dolby Surround AC-3 Dolby Surround AC-3 is the next generation of multichannel consumer audio. It uses a low bit-rate audio encoding scheme, creating a single composite data stream that contains five high-quality full-range channels, plus a sixth low frequency effect channel (called “5.1”). This unit is equipped with 5 CH DISCRT terminals for Dolby Surround AC-3. To listen to a 5 CH DISCRT SOURCE: Press the LD/TV button so that “5 CH DISCRT” appears on the display. To cancel it, press the switch again. LD/TV 28 • When you switch to “5 CH DISCRT” mode, the Digital Sound Field processor features of this unit are no longer available. The CENTER MODE switch, DELAY TIME switch and EFFECT switch also no longer work. • Signals connected to the 5CH DISCRT INPUT are not output to the tape decks or video recorders. To record the signals from an LD player, you must connect the player to the LD/TV terminals. The following adjustments can be done on the remote control transmitter as well as on the front panel. Adjustment of the FRONT LEVEL You can “fine-tune” the sound output level of the front effects speakers after setting the output level according to the instructions in “Speaker balance adjustment” on page 16. LEVEL FRONT Press the “+” or “–” FRONT LEVEL key on the remote control transmitter. As you change the volume level, the front panel LCD will display the value. If you press the “+” or “–” key continuously, the level will continuously change except for a momentary pause at the preset point (80). • Once the output level is adjusted, the level value will be the same in all the digital sound field programs. Note: When 5 CH DISCRT or DOLBY PRO LOGIC is used, the FRONT LEVEL control will not function. Adjustment of the CENTER LEVEL You can adjust the sound output level of the center channel speaker even if the output level is already set in “Speaker balance adjustment” on page 16. LEVEL CENTER Press the “+” or “–” CENTER LEVEL key on the remote control transmitter. As you change the volume level, the front panel LCD will display the value. If you press the “+” or “–” key continuously, the level will continuously change except for a momentary pause at the preset point (80). • The center channel speaker is used only in DOLBY PRO LOGIC, DOLBY PRO LOGIC ENHANCED, 70 mm MOVIE THEATER, TV THEATER, SPORTS and 5 CH DISCRT modes. • Once the output level is adjusted, the level value will be the same in all the digital sound field programs. Note: If the digital sound field program STADIUM, ROCK CONCERT, JAZZ CLUB, CHURCH, or CONCERT HALL is selected, the CENTER LEVEL control will not function. Adjustment of the REAR LEVEL You can adjust the sound output level of the rear speakers even if the output level is already set in “Speaker balance adjustment” on page 16. • Once the output level is adjusted, the level value will be the same in all the digital sound field programs. LEVEL REAR Press the “+” or “–” REAR LEVEL key on the remote control transmitter, the level value changes continuously. However, the value stops changing momentarily at the preset point (80). 29 Adjustment of DELAY TIME You can adjust the time difference between the beginning of the source sound and the beginning of the effect sound with the DELAY TIME control. The DELAY TIME control is effective with all programs. By applying more or less delay, sound effects, background noise, and ambient noise coming at you from the rear speakers can be enhanced or subdued for extra effect. 1. PRO LOGIC from 15 to 30 milliseconds (Preset value: 20 ms) 2. PRO LOGIC ENHANCED from 15 to 30 milliseconds (Preset value: 20 ms) 3. 70 mm MOVIE THEATER from 15 to 30 milliseconds (Preset value: 17 ms) 4. TV THEATER from 1 to 50 milliseconds (Preset value: 28 ms) 5. SPORTS from 1 to 50 milliseconds (Preset value: 20 ms) 6. STADIUM from 1 to 50 milliseconds (Preset value: 45 ms) 7. ROCK CONCERT from 1 to 50 milliseconds (Preset value: 22 ms) 8. JAZZ CLUB from 1 to 50 milliseconds (Preset value: 26 ms) 9. CHURCH from 1 to 50 milliseconds (Preset value: 40 ms) 10. CONCERT HALL from 1 to 50 milliseconds (Preset value: 30 ms) By continuously pressing “+” or “–” on the DELAY TIME control, the value changes continuously. However, the value stops changing momentarily at the preset point. DELAY TIME Note: Adding too much delay will cause an unnatural effect with some sources. Experiment with the DELAY TIME control to create the effect that you find most suitable. Note: The values of the DELAY TIME, CENTER LEVEL, FRONT LEVEL and REAR LEVEL you set the last time will remain memorized even when the power of this unit is off. However, if the power cord is kept disconnected for more than one week, these values will be automatically changed back to the original factory settings. 30 SETTING THE SLEEP TIMER If you use the SLEEP timer of this unit, you can make this unit turn off automatically. When you are going to sleep while enjoying a broadcast or other desired input source, this timer function is helpful. Notes: • The SLEEP timer can be controlled only with the remote control transmitter. • The components on which the SLEEP timer is effective are the sources connected to the SWITCHED AC OUTLET(S) on the rear panel of this unit. To set the SLEEP time To cancel the selected SLEEP time 1 1 SLEEP SLEEP Press the SLEEP key until “SLEEP OFF” appears on the display. SLEEP SLEEP Flashes continuously. Whenever the SLEEP key is pressed, the SLEEP time will change as follows: (Minutes) SLEEP The SLEEPtimer is OFF. (The indication before the SLEEP key is pressed.) After a while, the display returns to the indication before the SLEEP timer is set, and the “SLEEP” indicator stops flashing and lights up. 2 The unit will be turned off automatically at the selected SLEEP time. Press once or more so that the display returns to the indication before the SLEEP timer is set. (“SLEEP” will go off from the display.) Note: The SLEEP timer setting can also be canceled by turning off the power with the POWER switch or disconnecting the power plug of this unit from the AC outlet. 31 REMOTE CONTROL TRANSMITTER Battery installation Remote control transmitter operation range Main Room Remote Remoto control sensor 2 1 Within approximately 7 m (23 feet) 3 30° 30° Room 2 Remote 2 1 ␣ Notes: • There should be no large obstacles between the remote control transmitter and the main unit. • If the remote control sensor is directly illuminated by strong lighting (especially an inverter type of fluorescent lamp etc.), it might cause the remote control transmitter not to work correctly. In this case, reposition the main unit to avoid direct lighting. 3 STANDBY mode (Singapore model only) Battery replacement If you find that the remote control transmitter must be used closer to the main unit, the batteries are weak. Replace both batteries with new ones. Notes: • Use only AA, LR6, UM-3 batteries for replacement. • Be sure the polarities are correct. (See the illustration inside the battery compartment.) • Remove the batteries if the remote control transmitter will not be used for an extended period of time. • If batteries leak, dispose of them immediately. Avoid touching the leaked material or letting it come in contact with clothing, etc. Clean the battery compartment thoroughly before installing new batteries. 32 While the power is on, pressing the POWER key on the remote control transmiter switches the unit to the STANDBY mode. (In this mode, the indicator is half illuminated.) POWER on mode STANDBY mode The remote control transmitter provided with this unit is designed to control all the most commonly used functions of the unit. If the CD player, tape deck, etc. connected to this unit are YAMAHA components designed for remote control compatibilty, then this remote control transmitter will also control various functions of each component. • When you operate this unit and/or other YAMAHA components with this remote control transmitter, set the YPC-USER-LEARN switch to the YPC (Yamaha Preset Code) position. For Control of This Unit Main Room Remote Room 2 Remote TRANSMIT USER LEARN /LEARN YPC POWER Turns the power on/off. POWER SLEEP SKIP TV VCR DISC SKIP AUX PAUSE/STOP PLAY — PRESET SLEEP Refer to “SETTING THE SLEEP TIMER” on page 31. SKIP PHONO DISC SKIP SEARCH PAUSE/STOP DECK A/B PRESET — SEARCH Tuner keys Controls tuner. +: Selects higher preset station number. –: Selects lower preset station number. A/B/C/D/E Selects the page (A - E) of preset station buttons. PLAY CD A/B/C/D/E TUNER + STOP PLAY TAPE 1 Tuner keys Controls tuner. DIR A DECK A/B DIR A DIR B TAPE 2 MON SEARCH PAUSE/STOP PLAY LD/TV CHAPTER/CH DISPLAY STOP VCR 1 VCR 2 REC MUTE REC/PAUSE — + PRO LOGIC ENHANCED 70mm MOVIE THEATER TV THEATER 1 2 3 4 SURROUND SPORTS STADIUM ROCK JAZZ CLUB 5 6 7 8 CHURCH HALL 9 10 V–AUX EFFECT DSP ON/OFF MASTER VOLUME — + + PAUSE/STOP + DELAY TIME REAR LEVEL — + RESET CLEAR + CD A/B/C/D/E TUNER PLAY TAPE 1 STOP TAPE 2 PLAY LD/TV STOP VCR 1 VCR 2 REMOTE BOURCE CONTROLER V–AUX TEST CENTER LEVEL — + +: Selects higher preset station number. –: Selects lower preset station number. A/B/C/D/E Selects the page (A - E) of preset station buttons. Input selector keys Selects input source. + DIR B — CHAPTER FRONT LEVEL For the DSP control keys, refer to the page 26. Input selector keys Selects input source. PHONO MUTING — — (MASTER) VOLUME +/– Turns the volume level up/down. Muting Key Mutes the master volume. While mute is engaged, an indicator on the master VOLUME control flashes. Press again to un-mute the master volume. 33 For Other Component Control Identify the remote control transmitter keys with your component’s keys. If these keys are identical, their functions will be the same. On each key function, refer to the corresponding instruction on your component’s manual. TRANSMIT USER LEARN /LEARN YPC SKIP 1 POWER SLEEP TV VCR AUX DISC SKIP PAUSE/STOP PLAY — PRESET SKIP PHONO PHONO + TUNER PLAY TAPE 1 STOP TAPE 2 PLAY LD/TV STOP VCR 1 DISC SKIP 1 SEARCH PLAY CD A/B/C/D/E TUNER STOP PLAY TAPE 1 DIR A DIR B TAPE 2 MON SEARCH PAUSE/STOP PLAY LD/TV CHAPTER/CH DISPLAY STOP VCR 1 PAUSE/STOP DECK A/B PRESET — + DIR A SEARCH DIR B 2 DECK A/B 2 PAUSE/STOP — CHAPTER REC MUTE REC/PAUSE + 3 3 — 1 2 3 CD A/B/C/D/E VCR 2 REMOTE BOURCE CONTROLER V–AUX + CD player keys Controls compact disc player. DISC SKIP is applicable only to compact disc changer. Tape deck keys Controls tape deck. DIR A, B and DECK A/B are applicable only to double cassette tape deck. For a single cassette deck with automatic reverse function, pressing DIR A will reverse the direction of tape running. LD player keys Controls LD player. Using the Remote Transmitters If you use the Room 2 Remote transmitter (the transmitter for the second room) in the main room, the input selector keys of this remote affect the settings in the second room, not the main room. The other keys on the transmitter work the same in both the main room and the second room. If you use the Main Remote transmitter (the transmitter for the main room) in the second room, the keys that appear on the Room 2 Remote transmitter work except the input selector keys. The indicator information: ROOM 2 ROOM 2 CONTROL 34 1 2 1 Lights up momentarily when the Room 2 Remote transmitter is used in the main room. 2 Lights up momentarily when the Room 2 Remote transmitter is used in the second room. REMOTE CONTROL “LEARNING” FUNCTION All of the keys on this remote control transmitter can be programmed to “learn” key-functions from other remote control transmitters without losing the preset key functions. By using this feature, this unit can then be used in place of one or more other remote control transmitters, thus making operation of your various audio and video components more convenient. Use the included user program sheets to indicate a new function learned for each key. Note: There may occasionally be instances in which, due to the signal-coding and modulation employed by the other remote control transmitter, this unit will not be able to “learn” its signals. TRANSMIT USER LEARN /LEARN YPC TRANSMIT/LEARN indicator POWER Blank keys These keys have no preset functions and are used only for learning other remote control transmitter’s functions. SLEEP TV VCR SKIP AUX PHONO DISC SKIP SEARCH PLAY CD A/B/C/D/E TUNER STOP PLAY TAPE 1 DIR A DIR B TAPE 2 MON SEARCH PAUSE/STOP PLAY LD/TV CHAPTER/CH DISPLAY STOP VCR 1 VCR 2 PAUSE/STOP DECK A/B PRESET — SEARCH REC MUTE REC/PAUSE + — + PRO LOGIC ENHANCED 70mm MOVIE THEATER TV THEATER 2 3 4 1 YPC-USER-LEARN switc YPC : Set to this position when using preset key functions (for controlling this unit and/or YAMAHA components). ・ “YPC” is the abbreviation of YAMAHA Preset Code. USER : Set to this position when using “learned” key functions. LEARN : Set to this position when learning new key functions from other remote control transmitters. SURROUND SPORTS STADIUM ROCK JAZZ CLUB 5 6 7 8 CHURCH HALL 9 10 V–AUX EFFECT DSP ON/OFF MASTER VOLUME FRONT LEVEL — + + RESET button Press this button to “reset” the internal microcomputer which controls remote control operations. Microcomputer “reset” is necessary when the remote control freezes. ・ Pressing the RESET button will not erase learned functions. — + DELAY TIME REAR LEVEL — + RESET CLEAR + TEST CENTER LEVEL MUTING — — CLEAR button This button is used to clear one or all learned key functions. (Refer to page 37.) 35 To learn a new function 1 Set to the “LEARN” position. USER YPC LEARN 2 Press a key on this unit where a new function will be learned. About 5–10 cm (2–4 in). 3 Press and hold the key (on the other remote control transmitter) where the desired new function is. Lights up • When the TRANSMIT/LEARN indicator stops lighting, the learning is finished. 4 Repeat step 2 and 3 until all desired functions are successfully learned. 5 Set to the “USER” position. USER YPC LEARN Try operating your components. 36 Notes: • When you operate the desired component with this remote control transmitter, TRANSMIT/LEARN indicator will flash steadily. • The originally preset function of a key is still available in the USER position if a new function has not been learned to the key. • Successful learning to a key results in the erasure of previously learned functions and their replacement by the newly learned ones. • If there is no more room in the memory area for a function to be learned, the TRANSMIT/LEARN indicator will flash on and off. In this case, even if some keys are not occupied with functions from other remote control transmitters, no further learning is possible. Memory back-up All of the learned functions will be retained while you replace the batteries. However, if no batteries are installed for a few hours, the learned functions will be erased and will have to be learned again. To clear a learned function 1 To clear all learned functions 1 Set to the “USER” position. Set to the “LEARN” position. USER YPC LEARN USER YPC LEARN 2 2 Press and hold the CLEAR button using the point of a mechanical pencil, etc. Press and hold the CLEAR button using the point of a mechanical pencil, etc. CLEAR 3 CLEAR 3 Press and hold the key where the learned function to be deleted is until the indicator flashes 3 times. Press and hold any key until the indicator flashes 7 times TRANSMIT /LEARN TRANSMIT /LEARN • To clear two or more functions, repeat step 2 and 3. Note: If a key is not pressed soon after the CLEAR button is pressed, this unit will automatically return to the status that was in effect before the CLEAR button was pressed. Troubleshooting guide SYMPTOM CAUSE REMEDY The remote control transmitter does not work. The batteries of this remote control transmitter are weak. Replace the batteries with new ones and press the RESET button on the remote control transmitter. Learning cannot be made successfully. (The TRANSMIT/LEARN indicator does not light up or flash.) The internal microcomputer “freezes”. Replace the batteries (and press the RESET button for this remote control transmitter). The batteries of this remote control transmitter and/or the other remote control transmitter are weak. Place the remote control transmitters with the proper distance. The distance between the two remote control transmitters is too long or too short. Learning is not possible. The signal coding or modulation of the other remote control transmitter is not compatible with this remote control transmitter. Further learning is not possible without deleting unnecessary commands. Memory capacity is full. Press the RESET button on the remote control transmitter. 37 TROUBLESHOOTING If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and contact your authorized YAMAHA dealer or service center for help. SYMPTOM REMEDY The unit fails to turn on when the POWER switch is pressed. Power cord is not plugged in or is not completely inserted. Firmly plug in the power cord. No sound or no picture. Incorrect output cord connections. Connect the cords properly. If the problem persists, the cords may be defective. Appropriate input selector is not pressed. Press the appropriate input selector corresponding to the input source. The protection circuit has been activated because of short circuit etc. Turning the unit off and then on will reset the protection circuit. The SLEEP timer functioned. Do not make the SLEEP timer function. Incorrect setting of the BALANCE control. Adjust it to the appropriate position. Incorrect cord connections. Connect the cords properly. If the problem persists, the cords may be defective. Incorrect cord connections. Firmly connect the audio plugs. If the problem persists, the cords may be defective. No connection from the turntable to the GND terminal. Make the GND connection between the turntable and this unit. The sound suddenly goes off. Only one side speaker outputs the sound. Amplifier CAUSE Sound “hums”. The volume level is low while playing a record. The record is being played on a turntable with an MC cartridge. The player should be connected to the unit through the MC head amplifier. The volume level cannot be increased, or sound is distorted. The power to the component connected to the REC OUT terminals of this unit is off. Turn the power to the component on. No sound from the rear speakers. The sound output level to the rear speakers is set to 0. Turn up the sound output level with the REAR LEVEL control. The monaural sound source is played in DOLBY PRO LOGIC or DOLBY PRO LOGIC ENHANCED mode. Select another program suitable for the monaural sound source. The sound output level to the center speaker is set to 0. Turn up the sound output level with the CENTER LEVEL control. The center channel mode is in PHANTOM mode. Select NORMAL or WIDE. Incorrect sound field program selection. Select the appropriate program. No sound from the center speaker. others Remote control transmitter AM FM No sound field program is selected. 38 FM stereo reception is noisy. Because of the characteristics of FM stereo broadcasts, this is limited to cases where the transmitter is too far away or the antenna input is poor. Check the antenna connections. Try using a multiple element FM antenna. There is distortion and clear reception cannot be obtained even with a good FM antenna. There is multipath interference. Adjust antenna placement to eliminate multipath interference. A desired station cannot be tuned in with Auto tuning. The station is too weak. Use Manual tuning mode. Use a high quality directional FM antenna. A desired station cannot be tuned in with Auto tuning. Weak signal or loose antenna connections. Tighten the AM loop antenna connections and rotate it for best reception. Use Manual tuning mode. There are continuous crackling and hissing noises. Noises will result from lighting, fluorescent lamps, motors, thermostats and other electrical equipment. Use an outdoor antenna and a ground wire. This will help somewhat but it is difficult to eliminate all noise. There are buzzing and whining noises (especially in the evening). A television set is being used nearby. Relocate this unit away from the TV. The remote control transmitter does not work. Direct sunlight or lighting (of an inverter type of fluorescent lamp etc.) is striking the remote control sensor of the main unit. Change the position of the main unit. The batteries of this remote control transmitter are too weak. Replace the batteries with new ones. The power to this unit is off. Turn the power to this unit on. The sound is degraded when monitoring is performed by using the headphones connected to the compact disc player or cassette deck which are connected with this unit. SPECIFICATIONS AUDIO SECTION Minimum RMS Output Power per Channel MAIN L, R 8 ohms, 20 Hz to 20 kHz, 0.015% THD .................................................................. 100W+100W 6 ohms, 20 Hz to 20 kHz, 0.04% THD [U.S.A. model only] .......................... 120W+120W Center 8 ohms, 1 kHz, 0.015% THD ......................... 100W Front L, R 8 ohms, 1 kHz, 0.08% THD .................. 35W+35W Rear L, R 8 ohms, 1 kHz, 0.08% THD .................. 35W+35W Maximum Output Power [General model only] 8 ohms, 1 kHz, 10% THD (MAIN L/R) ............................................................. 135W+135W Dynamic Power per Channel (by IHF Dynamic Headroom measuring method) 8/6/4/2 ohms ...................... 130/160/215/310W Dynamic Headroom [U.S.A. and Canadian models only] 8 ohms .......................................................... 1.14 dB Power Band Width 8 ohms, 50W, 0.08% THD ....................................................... 10 Hz to 50 kHz Damping Factor 8 ohms, 20 Hz to 20 kHz .................... 200 or more Input Sensitivity/Impedance PHONO MM ........................... 2.5 mV/47 k-ohms 5 ch DISCRT/CD/TAPE/LD·TV/VCR .................................................. 150 mV/47 k-ohms MAIN IN ...................................... 1.0V/47 k-ohms Maximum Input Signal PHONO MM (1 kHz 0.02% THD) ....................................................... 110 mV or more CD/TAPE/LD·TV/VCR (EFFECT ON) (1 KHZ 0.5% THD) ........................... 2.2V or more Output Level/Impedance REC OUT ............................... 150 mV/1.0 k-ohms PRE OUT (MAIN) ...................... 1.0V/1.5 k-ohms ROOM 2 OUT ......................... 150mV/1.5 k-ohms LPF (EFFECT OFF) .................... 3.5V/2.7 k-ohms Headphone Jack Rated Output/Impedance (8 ohms, 1 kHz, 150 mV) ............ 0.55V/390 ohms Frequency Response (20 Hz to 20 kHz) MAIN IN .................................................... 0±0.2 dB CD/TAPE/LD·TV/VCR (MAIN L/R) ..................................................................... 0±0.5 dB RIAA Equalization Deviation PHONO MM ............................................. 0±0.5 dB Total Harmonic Distortion PHONO MM to REC OUT 20 Hz to 20 kHz, 1V ................... 0.01% or less CD/TAPE/LD·TV/VCR (EFFECT OFF) to SP OUT 20 Hz to 20 kHz 50W/8 ohms 0.015% or less CD/TAPE/LD·TV/VCR to SP OUT FRONT, REAR 1 kHz, 17.5W/8 ohms .................. 0.3% or less Signal-to-Noise Ratio (IHF-A Network) PHONO MM to REC OUT (5 mV Input Shorted) ........................................................... 86 dB or more CD/TAPE/LD·TV/VCR to SP OUT (InputShorted, EFFECT OFF) ........ 98 dB or more Residual Noise (IHF-A Network) SP OUT (MAIN L/R) ..................... 170 µV or less Channel Separation (Vol. –30 dB, EFFECT OFF) PHONO MM (Input Shorted 1 kHz/10 kHz) ................................ 60 dB or more/55 dB or more CD/TAPE/LD·TV/VCR (Input 5.1 k-ohms Shorted 1 kHz/10 kHz) ................................ 60 dB or more/45 dB or more Tone Control Characteristics BASS: Boost/cut ............................. ±10 dB (50 Hz) Turnover Frequency ..................... (350 Hz) TREBLE: Boost/cut .................... ±10 dB (20 kHz) Turnover Frequency .............. (3.5 kHz) Filter Characteristics LPF (fc=200 Hz) ....................................... 6 dB/oct Gain Tracking Error (0 to –70 dB) ................................................................ 3 dB or less Tuner Output Level/Impedance FM 100% MOD, 1 kHz ......... 500 mV/2.2 k-ohms AM 30% MOD, 1 kHz .......... 150 mV/2.2 k-ohms Bass Extension ...................................... +6 dB (50 Hz) Muting ....................................................................... –∞ VIDEO SECTION Video Signal Type [U.S, Canadian and General models] ........ NTSC [Australian, Singapore and General models] ............................................................................ PAL Video Signal Level .......................... 1 Vp-p/75 ohms S-Video Signal Level Y ................................................... 1 Vp-p/75 ohms C ............................................ 0.286 Vp-p/75 ohms Maximum Input Level ................... 1.5 Vp-p or more Signal-to-Noise Ratio .......................... 50 dB or more Monitor Out Frequency Response ............................................ 5 Hz to 10 MHz, –3 dB FM TUNER SECTION Tuning Range [U.S.A. and Canadian models] .................................................... 87.5 to 107.9 MHz [Australian, Singapore and General models] .................................................... 87.5 to 108.0 MHz 50 dB Quieting Sensitivity (IHF, 75 ohms) Mono ........................................... 1.55 µV (15.1 dBf) Stereo ............................................. 21 µV (37.7 dBf) Usable Sensitivity (75 ohms) (30 dB S/N Quieting, 1 kHz, 100% mod.) ......................................................... 0.8 µV (9.3 dBf) Image Response Ratio ........................................ 45 dB IF Response Ratio ............................................... 80 dB Spurious Response Ratio ................................... 70 dB AM Suppression Ratio ....................................... 55 dB Capture Ratio ..................................................... 1.5 dB Alternate Channel Selectivity ........................... 85 dB Signal-to-Noise Ratio (IHF) Mono/Stereo ..................................... 80 dB/75 dB Harmonic Distortion (1 kHz) Mono/Stereo ............................................ 0.1/0.2% Stereo Separation (1 kHz) .................................. 50 dB Frequency Response 20 Hz to 15 kHz ........................................ 0 ±1.5 dB Maximum Power Consumption [General models] ............................................ 790W AC OUTLETS [U.S.A model] 2 SWITCHED OUTLETS .......... 120W max. total 1 UNSWITCHED OUTLET ................ 200W max. [Canadian model] 2 SWITCHED OUTLETS ........... 120W max. total 1 UNSWITCHED OUTLET ................ 180W max. [General model] 2 SWITCHED OUTLETS ........... 120W max. total 1 UNSWITCHED OUTLET ................ 200W max. [Australian model] 1 SWITCHED OUTLET ...................... 120W max. [Singapore model] 2 SWITCHED OUTLETS ........... 120W max. total Dimensions (W × H × D) ................................................. 435 × 171 × 470 mm (17-1/8” × 5-3/4” × 15-3/16”) Weight ................................................................ 17.8kg Accessories ..................................... AM loop antenna Indoor FM antenna Remote control transmitter × 2 Batteries × 2 User Program Sheets Specifications are subject to change without notice. AM TUNER SECTION Tuning Range [U.S.A., Canadian and General models] ....................................................... 530 to 1,710 kHz [Australian and Singapore models] ....................................................... 531 to 1,611 kHz Usable Sensitivity ....................................... 100 µV/m Selectivity ............................................................. 32 dB Signal-to-Noise Ratio ......................................... 50 dB Image Response Ratio ........................................ 40 dB Spurious Response Ratio ................................... 50 dB Harmonic Distortion (1 kHz) ............................. 0.3% GENERAL Power Supply [U.S.A. and Canadian models] ....................................................... AC 120V, 60 Hz [Australian model] ..................... AC 240V, 50 Hz [General model] ........................... AC 110/120/220/240V, 50/60 z [Singapore model] ........................ AC230V, 50Hz Power Consumption [U.S.A. model] ................................................ 400W [Canadian model] .......................... 450W/600 VA [Australian, Singapore and General models] .......................................................................... 420W 39 YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77321 MARNE-LA VALLEE-CEDEX 2, FRANCE ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND SCANDINAVIA A.B J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA VT26690 Printed in Japan
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40

Yamaha RX-V2090 Handleiding

Categorie
Cassettespelers
Type
Handleiding