Llitt 480014 Installatie gids

480014
Merk
Llitt
Model
480014
Type
Installatie gids
Thea Trafo 12V 0-100W
Art nr: 480014
Art.nr: UM1002 Version: 2021/12
Elektro Elco AB
sv en node da
nl
Made in China
* Scan QR code
for more info.
113
44
28
12V
AC
20
50
(mm)
sv SÄKER INSTALLATION
Se till att spänningen är frånslagen före installation eller
underhåll.
en
-
Make sure that the mains power is switched off before
installation or maintenance.
de SICHERE INSTALLATION
Achten Sie darauf, vor Installation oder Wartung die
Stromversorgung auszuschalten.
nl VEILIGE INSTALLATIE
TURVALLISUUSOHJEET
Varmista, että jännite on kytketty päältä ennen asennusta
ja huoltoa.
no SIKKER INSTALLASJON
elektriker kontaktes.
Sørg for at spenningen er frakoblet før utføring av
installasjon eller vedlikehold.
fra varmekilder og i et godt ventilert rom.
da SIKKER INSTALLATION
vedligeholdelsen. Hvis dette kendskab mangler, kontakt en
Sørg for at spændingen er slået fra før installation eller
vedligeholdelse.
Lees deze voorschriften voordat u met de installatie begint, en
geef ze door aan de gebruiker van de installatie. Installatie en
onderhoud mag alleen worden verricht door personen met de
daartoe benodigde kennis en ervaring.
Indien u niet over de benodigde kennis beschikt, raadpleeg een
erkende elektricien.
Voor installatie en onderhoud altijd controleren of de stroomtoevoer
is uitgeschakeld. Installeer de armatuur volgens onderstaande
beschrijving. Plaats de LED-armaturen en de voedingseenheid ver
weg van warmtebronnen en in een goed geventileerde ruimte.
Elektro Elco AB
Installation
The electronic LED converter is exclusively designed for the Light Emitting Diode (LED) lamps and for indoor use. The electronic converter is
a switch mode power supplier with 12VAC constant output voltage.
An electronic protection circuit switches off the electronic converter in case of short circuit in the secondary circuit, overheat as well as open
circuit. This convertor is thermally protected device, the type of protection is automatic resetting type. After the removing of the faults, the
electronic LED converter is ready for operation again.
The unit conforms to the directive 2006/95/EC for the electromagnetic compatibility and the low voltage directive 2014/35/EU.
• The electronic converter can only be used with the LED lamps.
• The electronic converter is only suitable for use indoors. Protect the electronic converter against excessive heat (for permissible
operating temperature range see table).
• The loads indicated on the converter must neither exceed nor below the following values.
• Connect the LED lamps to the electronic LED converter with correct polarity according to the schematic drawing.
• If the electronic LED converter is used for purposes other than originally intended or it is connected in the wrong way, no liability can be
taken over for possible damages.
Rated supply voltage 220-240V
Frequency 50/60Hz
Input current 0,48A
Secondary voltage 11,2V
Lamp wattage 0-100W lamp
Efficiency ≥93%
Power factor ≥0,99λ
Input capacitance 100nF
Operating temperature ta 50°C
Max casing temperature tc Max. 80°C
Dimming
For LED Lamp, Proper matching between dimmer, lamp and driver
is required
Leading and trailing edge dimmers
Primary terminal 2-pole, screw terminal dia 5,2mm
Secondary terminal 2-pole, screw terminal dia 5,2mm
Lifetime 30 000h
*Before use, always check the compatibility with the LED lamps of the application.
220-240V~
Max.100W
N
L
LED LAMP
OFF
I
O
12V~
Thea Trafo 12V 0-100W
  • Page 1 1
  • Page 2 2

Llitt 480014 Installatie gids

480014
Merk
Llitt
Model
480014
Type
Installatie gids
Download PDF
rapport

in andere talen

Gerelateerde artikelen

Andere documenten