Yamaha PM5D/PM5D-RH de handleiding

PM5D Editor Owner’s Manual

Special Notices

•The software and this owner’s manual are the exclu-

sive copyrights of Yamaha Corporation.

•Copying of the software or reproduction of this

manual in whole or in part by any means is expressly

forbidden without the written consent of the manu-

facturer.

•Copying of the commercially available music

sequence data and/or digital audio ﬁles is strictly

prohibited except for your personal use.

•Yamaha makes no representations or warranties

with regard to the use of the software and documen-

tation and cannot be held responsible for the results

of the use of this manual and the software.

•This disc is a CD-ROM. Do not attempt to play the

disc on an audio CD player. Doing so may result in

irreparable damage to your audio CD player.

•The screen displays as illustrated in this owner’s

manual are for instructional purposes, and may

appear somewhat different from the screens which

appear on your computer.

•Future upgrades of application and system software

and any changes in speciﬁcations and functions will

be announced separately.

•The company names and product names in this

Owner’s Manual are the trademarks or registered

trademarks of their respective companies.

❏

Yamaha Pro Audio Global Site

http://www.yamahaproaudio.com/

Contents

Getting Started ......................................... 2

INPUT CH window .................................... 6

ST IN window ............................................ 9

FX RTN window....................................... 11

MIX window ............................................ 13

MATRIX window...................................... 15

STEREO window ...................................... 17

DCA window............................................ 19

Selected Channel window....................... 20

Patch Editor window............................... 38

Surround Editor window......................... 42

GEQ window............................................ 44

Effect Editor window............................... 46

DCA/Mute Group window...................... 50

Scene window ......................................... 53

Library window ....................................... 60

Meter window ......................................... 62

Timecode Counter window..................... 62

Sync window ........................................... 62

Keyboard Shortcuts................................. 63

Index........................................................ 64

*Speciﬁcations and descriptions in this owner ’s manual are

for information purposes only. Yamaha Corp. reserves the

right to change or modify products or speciﬁcations at any

time without prior notice. Since speciﬁcations, equipment

or options may not be the same in every locale, please

check with your Yamaha dealer.

PM5D Editor

Owner’s Manual

Description of menus and buttons

In the event that menu and button names on a Windows system are different from those on a Macintosh, this

manual uses the Windows menu and button names followed by the Macintosh menu and button names in paren-

theses.

PM5D Editor Owner’s Manual

Overview of PM5D Editor

PM5D Editor enables you to remotely control the Yamaha PM5D mixing console and to save the parameter settings

on your computer. To use PM5D Editor, you must ﬁrst perform the following operations:

1 Start and conﬁgure Studio Manager.

2 Start and conﬁgure PM5D Editor.

3 Synchronize PM5D Editor with your PM5D console (

➥

p.3).

For more information on using Studio Manager, refer to the Studio Manager Owner’s Manual.

Conﬁguring PM5D Editor

You must conﬁgure the following settings for each open Editor.

• Specify MIDI ports in the Setup window of Studio Manager before making the following settings.

•To open each Editor, double-click the icon of the console or device you want to edit.

❏

System Setup

To open the System Setup window, choose [System Setup] from the

[File] menu.

Be sure to specify the Input port and Output port.

Input port/Output port:

From the ports you speciﬁed in

Studio Manager, select the ports that the editor will use to commu-

nicate with the PM5D console.

Console Device ID:

PM5D Editor can control any one of up to

eight PM5D consoles, each with its own exclusive ID. Select the ID

of the console you want to control.

Channel Select:

These options determine whether or not chan-

nel selection is linked. When the PC->Console option is on, select-

ing a channel in PM5D Editor selects the same channel on the

console. When the Console->PC option is on, selecting a channel

on the console selects the same channel in PM5D Editor.

Conﬁrmation:

These check boxes specify whether a conﬁrma-

tion dialog box will appear when you store (Store Conﬁrmation), recall (Recall Conﬁrmation), patch (Patch Con-

ﬁrmation), or make a patch change that would modify an existing patch (Steal Patch Conﬁrmation).

Window Control from Console:

This option determines whether or not using the USER DEFINED KEYS

on the console enables you to remotely open and close the PM5D Editor windows.

Getting Started

NOTE

PM5D Editor Owner’s Manual

❏

Console Setup

To open the Mixer Setup window, choose [Mixer Setup] from

the [File] menu.

Pair Mode:

Select whether faders will be paired Horizontally

or Vertically.

Pan Nominal Position:

Select whether the signal will be at

nominal level when panned to the center (Center) or when

panned all the way to left or right (L<->R). You can make sepa-

rate settings for monaural channels and paired channels.

Bus Setup:

Select the MIX bus mode (VARI/FIXED) for

every two adjacent odd-numbered/even-numbered MIX buses.

MIX buses assigned as surround buses are indicated as “SUR-

ROUND” and cannot be changed.

Surround Bus Allocation:

Select the MIX buses (MIX 1–

8 or MIX 9–16) that will be used as surround buses.

Stereo B:

Specify whether the same signal as the STEREO A

bus will be sent to the STEREO B bus (Stereo Bus), or whether

the STEREO B bus will function as the CENTER bus for LCR

mode (Center Bus).

Surround Mode:

Select the surround mode (STEREO, 3-1,

5.1, 6.1).

Synchronizing PM5D Editor

When PM5D Editor starts up, the parameter settings on the console and the parameter settings in PM5D Editor may

be different. Therefore, you must ﬁrst match the parameter settings on the console with those in PM5D Editor. This

operation is called “synchronization.” Follow the steps below to synchronize PM5D Editor.

1 Select [Synchronize], then [Re-synchronize].

The following window opens.

2 Select whether you want to transfer your settings to PM5D

Editor, or vice versa.

At this time, the All Libs option determines whether or not Scene and

Library data is synchronized.

PC -> Console:

Tr ansfers the current parameter settings in PM5D Editor to your console.

Console -> PC:

Tr ansfers the current parameter settings of your console to the PM5D Editor.

3 Click [OK].

Do not operate the console while synchronization is in progress.

If you use the “Total Recall” function in Studio Manager, all selected Editors in Studio Manager are syn-

chronized with the corresponding devices.

Ofﬂine Edit Function

If you do not want to synchronize your console with PM5D Editor, select [Ofﬂine Edit] from the [Synchronization]

menu. To apply your off-line edits to your console, select [Re-Synchronize] from the [Synchronization] with the PC

-> Console option to synchronize the console with PM5D Editor.

The Ofﬂine Edit function is also activated when you click the [ONLINE]/[OFFLINE] button in the Sync window.

Some effect parameters in the console change their displayed values depending on the sampling fre-

quency. If you switch PM5D Editor from OFFLINE to ONLINE, displayed parameter values may change

because PM5D Editor loads the sampling frequency from the console and updates the display.

NOTE

PM5D Editor Owner’s Manual

Working with Sessions

All of your console’s mix settings in PM5D Editor, including Scene and library data, are called Sessions. The follow-

ing table describes how to handle Sessions.

When you save a session in the window of an editor, the settings of only that editor will be saved in a ﬁle. Session ﬁles

saved by PM5D Editor have a ﬁlename extension of “.YSE”. Files in which only the PM5D console data is saved (ﬁle-

name extension “.PM5”) can also be handled, allowing you to use a memory card to exchange data with the PM5D

console.

If you save a Session in the Studio Manager window, all selected Editor settings are saved in a ﬁle with a ﬁle extension

of “.YSM.”

Window operations

You can select and open each window from the [Win-

dows] menu. For the INPUT CH window and Effect Edi-

tor window, use the sub-menu to select the channels or

library you want to see.

In the Library window or Scene window, click the tabs

located at the top of the window to switch between

pages.

Creating a new Session

Choose [New Session] from the [File] menu.

Opening a previously saved Session

Choose [Open Session] from the [File] menu.

Saving the current Session

Choose [Save Session] from the [File] menu.

Saving the current Session with a new name

Choose [Save Session As...] from the [File] menu.

PM5D Editor Owner’s Manual

Undo/Redo Function

In PM5D Editor, you can cancel the latest operation (Undo) and also cancel the cancellation of the latest operation

(Redo). If you perform an Undo operation twice in a row, you can cancel the two most-recent operations. If you per-

form an Undo operation three times in a row, you can cancel the three most-recent operations. In this way, you can

cancel multiple recent operations. The following table describes how to use the Undo/Redo function.

Please note, however, that after you perform one of the following operations, you cannot successfully undo or redo

any previous operation:

•Operations on the PM5D console

• Quitting Studio Manager

•Changing the surround mode or pair mode

•Synchronizing with the PM5D console

•Session operations

•The GEQ [EQ FLAT] button

•Moving the fader positions by changing the GEQ variable width

You cannot Undo or Redo the following operations:

• Edits in the Setup window

• Synchronization

• Opening and closing the windows

• Resizing the windows

In the Library window, you can Undo or Redo only the most recent operation. You cannot cancel the pre-

ceding operations.

Other Functions

❏

Resetting to the default value (Ctrl ( ) + click)

Move the cursor to a control or a parameter value, then hold down the <Ctrl> key ( ) and click the mouse but-

ton to reset the value to the default (e.g., to reset an Input Channel fader to –

∞

, or reset a pan setting to Center).

❏

Ctrl ( ) +Shift+Click

Move the cursor to a fader or AUX Send control, then hold down the <Ctrl> key ( ) and <Shift> key and click

the mouse button to reset the value to the nominal level.

Undo

Choose [Undo] from the [Edit] menu.

Redo

Choose [Redo] from the [Edit] menu.

NOTE

PM5D Editor Owner’s Manual

This window displays the mix parameters of input channels 1–24 or 25–48. The window shows either the channel 1–

24 layer or the channel 25–48 layer. To open the other layer’s window, choose the [Windows] menu command

[INPUT CH] and choose “CH1-24” or “CH25-48.”

You can use the [View] menu to choose the parameters that will be displayed in the window.

Input patch

Here you can select an input source to assign to the input channel, from the following

choices.

+48V

Switches on/off the phantom power (+48V) of the internal head amp (PM5D-RH

model only) or of the external head amp (AD8HR, AD824) patched to the input chan-

nel.

HA GAIN

Drag the knob in the screen to adjust the gain of the internal head amp (PM5D-RH

model only) or of the external head amp (AD8HR, AD824) patched to the input chan-

nel.

NONE

No assignment

AD1–AD48

INPUT jacks 1–48

AD1L–AD4R

L/R channels of ST IN jacks 1–4

SLOT1-1, SLOT1-2...SLOT4-15, SLOT4-16

Input channels of an I/O card installed in slots

1–4

FXOUT1L, FXOUT1R...FXOUT8R,

FXOUT8L

L/R outputs of internal effects 1–8

2TR D1L, 2TR D1R...2TR D3L, 2TR D3R

L/R channels of 2TR IN DIGITAL jacks 1–3

2TR A1L, 2TR A1R...2TR A3L, 2TR A3R

L/R channels of 2TR IN ANALOG jacks 1/2

INPUT CH window

PM5D Editor Owner’s Manual

HPF (High Pass Filter)

Switches the high pass ﬁlter on/off. You can drag the numeric value up or down to edit

the cutoff frequency.

Ø (Phase)

Inverts the phase of the signal after AD conversion.

INSERT

Enables/disables the insert-out that is patched in the PM5D’s INSERT PATCH screen

(INPUT PATCH function).

DIRECT

Enables/disables the direct output that is patched in the PM5D’s DIRECT OUT PATCH

screen (INPUT PATCH function).

GATE

Tur ns the gate on/off. The indica-

tor immediately below the button

shows the gate’s on/off setting

and the open/closed status.

COMP (Compressor)

Switches the compressor on/off. When the compressor is on, the GR meter immediately

below the button shows the amount of gain reduction.

EQ (Equalizer)

Switches the EQ on/off. The graph immediately below the button shows the approxi-

mate response of the EQ. You can drag within the graph to edit the response of the EQ.

To reset the EQ to ﬂat response, hold down the <Ctrl> key ( key) of your computer

keyboard and click the graph.

DELAY

Switches the delay on/off. You can also edit the delay time by dragging the numeric

value located immediately below the button up or down

Channel number

Indicates the input channel number corresponding to this module. You can double-

click this number to open the Selected Channel window for this channel.

MIX SEND

The bar graphs in this area indicate the send levels of

the signals sent from the input channel to VARI-type

MIX buses. You can also adjust the send levels by drag-

ging a bar graph to left or right.

The bar graph display will change according to the

send position (pre/post) and on/off status of the signal

sent from the input channel to the MIX buses.

For FIXED-type MIX buses, the bar graph is ﬁxed at nominal level (0 dB),

and only the on/off status is shown.

N PAN

Sets the panning of the signal sent from the input channel to the STEREO bus.

O SELECT

Selects input channel for which you want to perform operations. This is linked with the

INPUT channel strip [SEL] keys on the PM5D panel. However it will no longer be

linked if you turn Channel Select off (➥ p.2) in the System Setup window.

P CH ON (Channel on) button

Switches the input channel on/off. This is linked with the INPUT channel strip CH

[ON] keys on the PM5D panel.

Gate= closed

(red)

Gate= open

(green)

Gate= off

Pre/on (green)

Pre/off (green)

Post/off (yellow)

Post/on (yellow)

NOTE

PM5D Editor Owner’s Manual

Q Channel name

This is a text box that displays the channel name. You can also edit the channel name in

this text box.

Note that while the channel number (

L) will not change even if you switch the pair

mode, the channel name display will change according to the pair mode.

For example if the CH1-24 layer is displayed, switching from Horizontal Pair mode to

Ve rtical Pair mode will change the channel name display from channels 1, 2, 3 ... 24, 25

to channels 1, 3, 5...45, 47.

R Fader

Adjusts the input level of the input channel. This is linked with the INPUT channel

strip faders on the PM5D panel.

The current fader value is shown in the numeric box immediately below the fader. The

level meter at the right of the fader shows the level of the input signal.

The numbers and

alphabetical letters at

the right of the fader

indicate the DCA

group and mute

groups to which that

channel belongs, and

show the Recall Safe

and Mute Safe status of

the channel.

S CUE

This button cue-monitors the signal of the input channel. This is linked with the

INPUT channel strip [CUE] keys on the PM5D panel.

The numbers of DCA groups to which this

channel belongs are shown in yellow.

The numbers of mute groups to which this

channel belongs are shown in red.

If this channel is set to Recall Safe, the R

character is shown in orange.

If this channel is set to Mute Safe, the M char-

acter is shown in red.

PM5D Editor Owner’s Manual

In this window you can view and edit the mix parameters of ST IN channels 1–4. You can use the [View] menu to

choose the parameters that will be displayed in the window.

A Input patch

Selects the input source that will be assigned to the ST IN channel. The input sources

that can be assigned are the same as for an input channel (➥ p.6).

B +48V

Switches on/off the phantom power (+48V) of the internal head amp (PM5D-RH

model only) or of the external head amp (AD824, AD8HR) patched to the ST IN chan-

nel.

C HA GAIN

Drag the knob in the screen to adjust the gain of the internal head amp (PM5D-RH

model only) or of the external head amp (AD824, AD8HR) patched to the ST IN chan-

nel.

D HPF (High Pass Filter)

Switches the high pass ﬁlter on/off. You can drag the numeric value up or down to edit

the cutoff frequency.

E Ø (Phase)

Inverts the phase of the signal after AD conversion.

F INSERT

Enables/disables the insert-out that is patched in the PM5D’s INSERT PATCH screen

(INPUT PATCH function). (The L/R settings are linked.)

G DIRECT

Enables/disables the direct out that is patched in the PM5D’s DIRECT OUT PATCH

screen (INPUT PATCH function). (The L/R settings are linked.)

ST IN window

PM5D Editor Owner’s Manual

H GATE

Tur ns the gate on/off. The indicator immediately below the button shows the gate’s on/

off setting and the open/closed status (➥ p.7).

I COMP (Compressor)

Switches the compressor on/off. When the compressor is on, the GR meter immediately

below the button shows the amount of gain reduction.

J EQ (Equalizer)

Switches the EQ on/off (the L/R settings are linked). The graph immediately below the

button shows the approximate response of the EQ. You can drag the graph to edit the

response of the EQ, or hold down the <Ctrl> key ( key) of your computer keyboard

and click the graph to reset it to a ﬂat response.

K DELAY

Switches the delay on/off. You can also edit the delay time by dragging the numeric

value located immediately below the button up or down

L Channel number

This is the number of the ST IN channel for this module. You can double-click this

number to open the Selected Channel window for this channel.

M MIX SEND

The send levels of the signals sent from the ST IN channel to the VARI-type MIX buses

are shown as bar graphs (the L/R settings are linked). You can also adjust the send levels

by dragging a bar graph to left or right.

The bar graph display will change according to the send position (pre/post) and on/off

status of the signal sent from the ST IN channel to the MIX buses (➥ p.7).

N PAN

Speciﬁes the panning of the signal sent from the ST IN channel to the STEREO bus.

(You can set L and R separately.)

O SELECT

Selects the ST IN channel for which you want to perform operations. (L and R can be

selected separately.) This is linked with the ST IN channel strip [SEL] keys on the

PM5D panel. However it will no longer be linked if you turn Channel Select off (➥ p.2)

in the System Setup window.

P CH ON (Channel on) button

Switches the ST IN channel on/off (the L/R settings are linked). This is linked with the

ST IN channel strip CH [ON] keys on the PM5D panel.

Q Channel name

This is a text box that displays the channel name. You can also edit the channel name in

this text box.

R Fader

Adjusts the input level of the ST IN channel. This is linked with the faders of the ST IN

channel strip on the PM5D panel.

The numbers and alphabetical letters at the right of the fader indicate the DCA group

and mute groups to which that channel belongs, and show the Recall Safe and Mute

Safe status of the channel (➥ p.8).

S CUE

This button cue-monitors the signal of the ST IN channel (L/R are linked). This is

linked with the ST IN channel strip [CUE] keys on the PM5D panel.

PM5D Editor Owner’s Manual

In this window you can view and edit the mix parameters of FX RTN channels 1–4. You can use the [View] menu to

choose the parameters that will be displayed in the window.

A Input patch

Selects the input source that will be assigned to the FX RTN channel. The input sources

that can be assigned are the same as for an input channel (➥ p.6).

B +48V

Switches on/off the phantom power (+48V) of the internal head amp (PM5D-RH

model only) or of the external head amp (AD8HR, AD824) patched to the FX RTN

channel.

C HA GAIN

Drag the knob in the screen to adjust the gain of the internal head amp (PM5D-RH

model only) or of the external head amp (AD8HR, AD824) patched to the FX RTN

channel.

D HPF (High Pass Filter)

Switches the high pass ﬁlter on/off. You can drag the numeric value up or down to edit

the cutoff frequency.

E Ø (Phase)

Inverts the phase of the signal after AD conversion.

F EQ (Equalizer)

Switches the EQ on/off (the L/R settings are linked). The graph immediately below the

button shows the approximate response of the EQ. You can drag the graph to edit the

response of the EQ, or hold down the <Ctrl> key ( key) of your computer keyboard

and click the graph to reset it to a ﬂat response.

FX RTN window

PM5D Editor Owner’s Manual

G Channel number

This is the number of the FX RTN channel for this module. You can double-click this

number to open the Selected Channel window for this channel.

H MIX SEND

The send levels of the signals sent from the FX RTN channel to the VARI-type MIX

buses are shown as bar graphs (the L/R settings are linked). You can also adjust the send

levels by dragging a bar graph to left or right.

The bar graph display will change according to the send position (pre/post) and on/off

status of the signal sent from the FX RTN channel to the MIX buses (➥ p.7).

I PAN

Speciﬁes the panning of the signal sent from the FX RTN channel to the STEREO bus.

(You can set L and R separately.)

J SELECT

Selects the FX RTN channel for which you want to perform operations. (L and R can be

selected separately.) This is linked with the FX RTN channel strip [SEL] keys on the

PM5D panel. However it will no longer be linked if you turn Channel Select off (➥ p.2)

in the System Setup window.

K CH ON (Channel on) button

Switches the FX RTN channel on/off. (The L/R settings are linked.) This is linked with

the FX RTN channel strip CH [ON] keys on the PM5D panel.

L Channel name

This is a text box that displays the channel name. You can also edit the channel name in

this text box.

M Fader

Adjusts the input level of the FX RTN channel. This is linked with the faders of the FX

RTN channel strip on the PM5D panel.

The numbers and alphabetical letters at the right of the fader indicate the DCA group

and mute groups to which that channel belongs, and show the Recall Safe and Mute

Safe status of the channel (➥ p.8).

N CUE

This button cue-monitors the signal of the FX RTN channel (L/R are linked). This is

linked with the FX RTN channel strip [CUE] keys on the PM5D panel.

PM5D Editor Owner’s Manual

In this window you can view and edit the parameters of MIX channels 1–24. You can use the [View] menu to choose

the parameters that will be displayed in the window.

A EQ (Equalizer)

Switches the EQ on/off. The graph immediately below the button shows the approxi-

mate response of the EQ. You can drag the graph to edit the response of the EQ, or hold

down the <Ctrl> key ( key) of your computer keyboard and click the graph to reset

it to a ﬂat response.

B COMP (Compressor)

Switches the compressor on/off. When the compressor is on, the GR meter immediately

below the button shows the amount of gain reduction.

C INSERT

Enables/disables the insert-out that is patched in the PM5D’s INSERT PATCH screen

(OUTPUT PATCH function).

D DELAY

Switches the delay on/off. You can also edit the delay time by dragging the numeric

value located immediately below the button up or down

E Channel number

Indicates the number of the MIX channel corresponding to this module. You can dou-

ble-click this number to open the Selected Channel window for this channel.

MIX window

PM5D Editor Owner’s Manual

F MTRX (Send level to MATRIX buses)

These bar graphs indicate the send levels of the signals

sent from the MIX channel to each MATRIX bus. You

can also adjust the send levels by dragging a bar graph

to left or right.

The bar graph display will change as follows according

to the send position (pre/post) and on/off status of the

signal sent from the MIX channel to the MATRIX

buses.

G TO ST (To STEREO)

This is an on/off switch for the signal sent from the MIX channel to the STEREO bus.

H PAN

Sets the panning of the signal sent from the MIX channel to the STEREO bus.

I VARI/FIXED

Indicates the type (VARI or FIXED) of the currently selected MIX bus. (This parameter

is for display only. You cannot switch between VARI and FIXED from within PM5D

Editor.)

If surround mode is enabled, MIX buses that are assigned as surround buses are dis-

played with the name of the surround channel (L, R, Ls, Rs ...), and the other MIX

buses are displayed as “FIXED.”

J SELECT

Selects the MIX channel for which you want to make settings. This is linked with the

MIX [SEL] keys in the MIX section of the PM5D panel. However it will no longer be

linked if you turn Channel Select off (➥ p.2) in the System Setup window.

K ON

Switches the MIX channel on/off.

L Fader

Adjusts the output level of the MIX channel. The current fader value is shown in the

numeric box immediately below the fader. The level meter at the right of the fader

shows the output level of the signal.

The numbers and alphabetical letters at the right of the fader indicate the DCA group

and mute groups to which that channel belongs, and show the Recall Safe and Mute

Safe status of the channel. (For the signiﬁcance of the numbers and alphabetical letters,

see ➥ p.8).

M CUE

This button cue-monitors the signal of the MIX channel. This is linked with the MIX

[CUE] keys in the MIX section of the PM5D panel.

Pre/on (green)

Pre/off (green)

Post/off (yellow)

Post/on (yellow)

PM5D Editor Owner’s Manual

In this window you can view and edit the parameters of MATRIX channels 1–8. You can use the [View] menu to

choose the parameters that will be displayed in the window.

MATRIX window

PM5D Editor Owner’s Manual

A MIX (Send levels from the MIX channels to the MATRIX bus)

Here you can view and edit the send levels of the signals sent from each MIX channel to

the MATRIX bus. The method of operation and the meaning of the display are the same

as for (

6) MTRX in the MIX window (➥ p.14).

B STEREO (Send levels from the STEREO channels to the MATRIX

bus)

Here you can view and edit the send levels of the signals sent from the STEREO A/B

channels to the MATRIX bus. The method of operation and the meaning of the display

are the same as for (

6) MTRX in the MIX window (➥ p.14).

C Channel number

Indicates the number of the MATRIX channel corresponding to this module. You can

double-click this number to open the Selected Channel window for this channel.

D EQ (Equalizer)

Switches the EQ on/off. The graph immediately below the button shows the approxi-

mate response of the EQ. You can drag the graph to edit the response of the EQ, or hold

down the <Ctrl> key ( key) of your computer keyboard and click the graph to reset

it to a ﬂat response.

E COMP (Compressor)

Switches the compressor on/off. When the compressor is on, the GR meter immediately

below the button shows the amount of gain reduction.

F INSERT

Enables/disables the insert-out that is patched in the PM5D’s INSERT PATCH screen

(OUTPUT PATCH function).

G DELAY

Switches the delay on/off. You can also edit the delay time by dragging the numeric

value located immediately below the button up or down

H SELECT

Selects the MATRIX channel for which you want to make settings. This is linked with

the MATRIX [SEL] keys in the MATRIX section of the PM5D panel. However it will no

longer be linked if you turn Channel Select off (➥ p.2) in the System Setup window.

I ON

This switches the MATRIX channel on/off. This is linked with the MATRIX [ON] keys

in the MATRIX section of the PM5D panel.

J Fader

This adjusts the output level of the MATRIX channel. The current fader value is shown

in the numeric box immediately below the fader. The level meter at the right of the

fader shows the output level of the signal.

The numbers and alphabetical letters at the right of the fader indicate the DCA group

and mute groups to which that channel belongs, and show the Recall Safe and Mute

Safe status of the channel. (For the signiﬁcance of the numbers and alphabetical letters,

see ➥ p.8).

K CUE

This button cue-monitors the signal of the MATRIX channel. This is linked with the

MATRIX [CUE] keys in the MATRIX section of the PM5D panel.

PM5D Editor Owner’s Manual

In this window you can view and edit the parameters of the STEREO A/B channels. You can use the [View] menu to

choose the parameters that will be displayed in the window.

STEREO window

PM5D Editor Owner’s Manual

A EQ (Equalizer)

Switches the EQ on/off (the L/R settings are linked). The graph immediately below the

button shows the approximate response of the EQ. You can drag the graph to edit the

response of the EQ, or hold down the <Ctrl> key ( key) of your computer keyboard

and click the graph to reset it to a ﬂat response.

B COMP (Compressor)

Switches the compressor on/off (the L/R settings are linked). When the compressor is

on, the GR meter immediately below the button shows the amount of gain reduction.

C INSERT

Enables/disables the insert-out that is patched in the PM5D’s INSERT PATCH screen

(OUTPUT PATCH function). (The L/R settings are linked.)

D DELAY

Switches the delay on/off. (L/R settings can be made independently.) You can also edit

the delay time by dragging the numeric value located immediately below the button up

or down

E Channel number

This is the channel number (STEREO A or B) of this module. You can double-click this

number to open the Selected Channel window for this channel.

F MTRX (Send level to MATRIX buses)

Here you can view and edit the send levels of the signals sent from the STEREO A/B

channel to each MATRIX bus. The method of operation and the meaning of the display

are the same as for (

6) MTRX in the MIX window (➥ p.14).

G BALANCE

Adjusts the left/right balance of the STEREO A/B channel.

H SELECT

Selects the STEREO A/B channel for which you want to make settings. (You can specify

L and R independently.) This is linked with the STEREO [SEL] key in the STEREO A/B

channel strip of the PM5D panel. However it will no longer be linked if you turn Chan-

nel Select off (➥ p.2) in the System Setup window.

I ON

This switches the STEREO A/B channel on/off. This is linked with the STEREO [ON]

key in the STEREO A/B channel strip of the PM5D panel.

J Fader

Adjusts the output level of the STEREO A/B channel. This is linked with the STEREO

fader in the STEREO A/B channel strip of the PM5D panel.

The current fader value is shown in the numeric box immediately below the fader. The

level meter at the right of the fader shows the output level of the signal.

The numbers and alphabetical letters at the right of the fader indicate the DCA group

and mute groups to which that channel belongs, and show the Recall Safe and Mute

Safe status of the channel. (For the signiﬁcance of the numbers and alphabetical letters,

see ➥ p.8).

K CUE

This button cue-monitors the signal of the STEREO A/B channel. This is linked with

the STEREO [CUE] key in the STEREO A/B channel strip of the PM5D panel.

PM5D Editor Owner’s Manual

In this window you can view and edit the parameters of DCA groups 1–8.

A DCA number

This is the number of the DCA group.

B MUTE

This switches DCA group muting on/off. This is linked with the DCA [MUTE] keys in

the DCA strip section of the PM5D panel.

C DCA group name

This is a text box that displays the DCA group name. You can also edit the DCA group

name in this text box.

D DCA fader

This fader adjusts the level of the DCA group. This is linked with the DCA faders in the

DCA strip section of the PM5D panel.

The current fader value is shown in the numeric box immediately below the fader.

When you hold down the <Ctrl> key ( key) and <Shift> key of your computer key-

board and click a fader, the corresponding fader will be set to nominal level (0 dB).

When the fader is at nominal level, the N character at the right of the fader is displayed

in green.

If a DCA group is set to Recall Safe, the R character at the lower right of the fader is dis-

played in orange.

E CUE

This button cue-monitors the DCA group. This is linked with the DCA [CUE] keys in

the DCA channel strip of the PM5D panel.

DCA window

PM5D Editor Owner’s Manual

Here you can set the parameters of the currently selected input channel (input channels 1–48, ST IN channels 1–4,

FX RTN channels 1–4) or output channel (MIX channels 1–24, MATRIX channels 1–8, STEREO A/B channels).

The type of parameters that can be edited in this window will depend on the type of the currently selected channel.

The parameters of the Selected Channel window are explained below, in the order of input channels (input channels

1–48, ST IN channels 1–4, FX RTN channels 1–4), MIX channels, MATRIX channels, and STEREO A/B channels.

If an input channel is selected

Unless otherwise speciﬁed, the parameters explained below are common to input channels 1–48, ST IN

channels 1–4, and FX RTN channels 1–4.

❏ CHANNEL SELECT (Channel selection)

A SELECT (Channel selection)

Indicates the number and name of the channel you are editing. To switch channels, use the SELECT button or the

/ buttons at left and right. You can also edit the channel name in the text box.

B PAIR

Indicates the pair status of the selected channel. You can click the heart symbol to enable/disable pairing.

C INPUT PATCH

Selects the input source assigned to the input channel (for the selectable input sources, ➥ p.6).

D LIBRARY

Accesses the INPUT CH page of the LIBRARY window.

Selected Channel window

NOTE

1 2 43

PM5D Editor Owner’s Manual

❏ HA GAIN/Ø/HPF (HA gain/phase/high-pass ﬁlter)

A HA GAIN

Adjusts the gain of the internal head amp (PM5D-RH model only) or of the external head amp (AD8HR, AD824)

patched to the input channel. The current setting is shown in the numerical box above the knob. You can also use

the +48V button to switch phantom power on/off.

B Ø (Phase)

Inverts the phase of the signal after AD conversion.

C HPF (High Pass Filter)

Use the HPF button at the right to switch the high-pass ﬁlter on/off. You can use the knob at left to adjust the cut-

off frequency. The current setting is shown in the numerical box above the knob.

❏ GATE (except for FX RTN channels)

A Gate graph

Indicates the approximate response for the gate of the currently selected channel.

B GR meter

This meter indicates the amount of gain reduction.

C TYPE

Indicates the type of the currently selected gate.

D THRESHOLD (Threshold level)

Speciﬁes the level at which the gate will open and close. The gate will open when the key-in signal exceeds this

level, and will close when the signal falls below this level.

E RANGE

Speciﬁes the amount by which the signal is attenuated while the gate is closed.

1 2 3

1 4

ML K N

PM5D Editor Owner’s Manual

F DECAY (Decay time)

Speciﬁes the time over which the gate will close after the hold time has elapsed.

G ATTACK (Attack time)

Speciﬁes the time from when the key-in signal exceeds the threshold level until the gate opens.

H HOLD (Hold time)

Speciﬁes the time that the gate will remain open after the key-in signal falls below the threshold.

I ON (On/off)

This button switches the gate on/off.

J LIBRARY

This button accesses the gate library. Clicking this button will open the GATE page of the LIBRARY window.

K LINK (Stereo link)

This button links the parameter settings and key-in signals of adjacent odd-numbered/even-numbered input

channels or the L/R sides of a ST IN channel, so that gating will operate in tandem for the two channels.

L KEY IN SOURCE

Select the desired key-in signal from the following choices.

M CUE

This button cue-monitors the currently selected key-in signal.

N KEY IN FILTER

Select the type of ﬁlter applied to the selected key-in signal; HPF (high pass ﬁlter), BPF (band pass ﬁlter), or LPF

(low pass ﬁlter). The ON/OFF button located immediately below switches the ﬁlter on/off.

If you’ve selected BPF, use the two knobs at right to adjust the band pass frequency and Q. If you’ve selected HPF

or LPF, use the knob at left to adjust the cutoff frequency.

SELF PRE EQ The pre-EQ signal of the currently selected input channel

SELF POST EQ The post-EQ signal of the currently selected input channel

CH 1–48 POST EQ The post-EQ signal of the corresponding input channel (however, you can only choose

channels belonging to the same group, within the seven groups CH1–8, CH9–16,

CH17–24, CH25–32, CH33–40, CH41–48, and ST IN 1L/1R–4L/4R).

ST IN 1L/1R – 4L/4R POST EQ

MIX 21–24 OUT

The output signal of the corresponding MIX channel immediately before the output

attenuation

PM5D Editor Owner’s Manual

❏ COMPRESSOR

A Compressor graph

Indicates the approximate response for the compressor of the currently selected channel.

B GR meter

This meter indicates the amount of gain reduction produced by the compressor.

C TYPE

Indicates the type of the currently selected compressor.

D THRESHOLD (Threshold level)

Speciﬁes the threshold level at which the compressor will operate. The input signal will start being compressed

when the key-in signal exceeds this level; compression will be removed when the signal falls below this level.

E RATIO

Speciﬁes the ratio at which the input signal will be compressed when the key-in signal exceeds the threshold.

F KNEE

Speciﬁes the sharpness at which the output level will change. You can select from HARD or 1–5.

G ATTACK (Attack time)

Speciﬁes the time from when the key-in signal exceeds the threshold level until the signal starts being compressed.

H RELEASE (Release time)

Speciﬁes the time from when the key-in signal falls below the threshold level until compression is removed.

I GAIN

Adjusts the gain of the signal after it has passed through the compressor.

J ON (On/off)

This button switches the compressor on/off.

K LIBRARY

This button accesses the compressor library. Clicking this button will open the COMP page of the LIBRARY win-

dow.

L LINK (Stereo link)

This button links the parameter settings and key-in signals of adjacent odd-numbered/even-numbered input

channels or the L/R sides of a ST IN channel, so that compression will operate in tandem for the two channels.

M COMP LINK GROUP (Compressor link group)

Selects the compressor link group (1–8) to which that channel belongs.

N KEY IN

Selects the signal that will be used as the key-in signal. The types of signal that can be selected are the same as for

the gate key-in signal (➥ p.22).

1 4

L N

PM5D Editor Owner’s Manual

❏ INSERT (except for FX RTN channels)

A ON (On/off)

Enables/disables insert-in/out.

B OUT (Insert out)

Here you can select the output port that will be assigned to insert-out, from the following choices.

C IN (Insert in)

Here you can select the input port that will be assigned to insert-in, from the following choices.

D POINT (Insert point)

Selects the position at which insert-in/out will be patched. Choose from Pre EQ, Post EQ, Pre Delay, or Post

Fader.

NONE No assignment

SLOT1-1, SLOT1-2...SLOT4-15, SLOT4-16 Output channels of an I/O card installed in slots 1–4

FXIN1L, FXIN1R...FXIN8R, FXIN8L L/R inputs of internal effects 1–8

GEQIN 1–12 Inputs of GEQ modules 1–12

2TR D1L, 2TR D1R...2TR D3L, 2TR D3R L/R channels of 2TR OUT DIGITAL jacks 1–3

NONE No assignment

AD1–AD48 INPUT jacks 1–48

SLOT1-1, SLOT1-2...SLOT4-15, SLOT4-16 Input channels of an I/O card installed in slots 1–4

FXOUT1L, FXOUT1R...FXOUT8R, FXOUT8L L/R outputs of internal effects 1–8

GEQOUT 1–12 Outputs of GEQ modules 1–12

2TR D1L, 2TR D1R...2TR D3L, 2TR D3R L/R channels of 2TR IN DIGITAL jacks 1–3

2TR A1L, 2TR A1R, 2TR A2L, 2TR A2R L/R channels of 2TR IN ANALOG jacks 1/2

1 2 3 4

PM5D Editor Owner’s Manual

❏ EQUALIZER

A EQ graph

Indicates the approximate response for the EQ of the currently selected channel.

B FLAT

If you click this button, the gain of all bands will be reset to 0.0 dB.

C Q

D F (Frequency)

E GAIN

These knobs adjust the Q, center frequency, and boost/cut amount for the four bands LOW, LO-MID, HI-MID,

and HIGH.

F (LOW shelving)

If this button is on, the LOW EQ will be switched to a shelving type (the Q knob of the LOW EQ will disappear).

G (HIGH shelving)

If this button is on, the HIGH EQ will be switched to a shelving type (the Q knob of the HIGH EQ will disap-

pear).

H LPF (Low Pass Filter)

If this button is on, the HIGH EQ will function as a low pass ﬁlter. The Q knob of the HIGH EQ will disappear,

and the GAIN knob will act as the low pass ﬁlter on/off switch.

I ON (On/off)

Switches the EQ on/off.

J LIBRARY

Accesses the INPUT EQ page of the LIBRARY window.

K TYPE I/TYPE II (EQ type)

Selects either TYPE I (an algorithm equivalent to the EQ in the earlier 02R series) or TYPE II (a newly developed

algorithm) as the EQ type.

L EQ LINK GROUP

Selects the EQ link group (1–8) to which that channel belongs.

PM5D Editor Owner’s Manual

M ATT (Attenuation)

Adjusts the amount of attenuation/gain following AD conversion.

❏ DELAY

A TIME (Delay time)

Adjusts the delay time for each channel.

B ON (On/off)

Switches the delay on/off. The current value (ms units) is shown in the box at the right.

❏ M/S DECODE (except for FX RTN channels)

A S-GAIN

This knob sets the proportionate level of the S mic relative to the level of the M

mic. The current value (dB units) is shown in the box at the right.

B ON (On/off)

This button switches M/S decoding on/off for two adjacent odd-numbered/even-

numbered input channels (or ST IN channel L/R).

❏ DCA GROUP / MUTE GROUP / SAFE

A DCA GROUP

Selects the DCA group (1–8) to which that channel belongs.

B MUTE GROUP

Selects the mute group (1–8) to which that channel belongs.

C RECALL SAFE / MUTE SAFE

These enable/disable Recall Safe and Mute Safe for the chan-

nel.

1 2

1 2 3

PM5D Editor Owner’s Manual

❏ Pan / Fader

A DIRECT (except for FX RTN channels)

Tur ns the direct output on/off.

B Direct Output Port (except for FX RTN channels)

Choose the port from which this input channel 1–48 or this ST IN channel 1–4 will be

directly output.

C FOLLOW PAN

Use the following two buttons to specify how the signal sent from the input channel to

the MIX bus will be affected by the TO ST PAN knob (

5).

•VARI button

If this button is on, the PAN knob displayed in the CH to MIX area will be linked

with the TO ST PAN knob if VARI-type MIX buses are paired.

• FIXED button

If this button is on, the signal from after the TO ST PAN (5) knob will be sent to

FIXED-type MIX buses.

D TO ST (To stereo)

This is an on/off switch for the signal sent from the input channel to the STEREO bus.

This is linked with the [TO STEREO] key in the SELECTED CHANNEL section of the

panel.

E TO ST PAN (To stereo pan)

Adjusts the panning of the signal sent from the input channel to the STEREO bus. This

is linked with the encoder of each channel if PAN is selected as the encoder mode, and

with the [PAN] encoder of the SELECTED CHANNEL section.

F LCR

Tur ns LCR mode on/off for each channel. If this is turned on for a channel, you can use

the TO ST PAN (

5) knob to simultaneously control the level of the signal sent to the

STEREO bus L/R channels and CENTER channel.

G CSR (Center Side Ratio)

This adjusts the level ratio (0–100%) of the CENTER channel relative to the STEREO

bus L/R channels. To change the value, drag upward or downward inside the numerical

box.

H ON

Switches the input channel on/off. This is linked with the INPUT channel strip CH

[ON] keys on the PM5D panel.

I Fader

Adjusts the input level of the input channel. This is linked with the INPUT channel

strip faders on the PM5D panel. The current value is shown in the numerical box

immediately below.

J CUE

This button cue-monitors the signal of the input channel. This is linked with the

INPUT channel strip [CUE] keys on the PM5D panel.

NONE No assignment

SLOT1-1, SLOT1-2...SLOT4-16 Output channels of an I/O card installed in slots 1–4

2TR D1L, 2TR D1R...2TR D3R L/R channels of 2TR OUT DIGITAL jacks 1–3

PM5D Editor Owner’s Manual

❏ CH to MIX (Channel to mix)

A MIX send level

This adjusts the send level of the signal sent from the input channel to VARI-type MIX buses. The current value is

shown in the numerical box immediately above.

B Pair

This indicates the pairing status of adjacent odd-numbered/even-numbered MIX channels. You can click the

heart symbol to enable/disable pairing.

C ON (MIX send on/off)

This is an on/off switch for the signal sent from the input channel to the MIX bus.

D PRE (Pre/Post)

This selects PRE or POST as the point from which the signal is sent from the input channel to the MIX bus.

E CH to MIX PRE POINT

This selects PRE EQ or PRE FADER as the point from which the signal is sent when the PRE button (4) is set to

PRE.

If the PRE button is set to POST, you can select either POST ON or POST TO ST as the signal send loca-

tion individually for each MIX bus (

➥

p.33).

NOTE

PM5D Editor Owner’s Manual

If a MIX channel is selected

❏ CHANNEL SELECT (Channel selection)

Except for the fact that your editing applies to a MIX channel, this is the same as for an input channel (➥ p.20).

❏ COMPRESSOR

Except for the fact that the COMP LINK GROUP is A–F, and that the types of signal that can be selected for key-

in are different, this is the same as for the compressor of an input channel (➥ p.23).

❏ INSERT

Except for the fact that the insert points that can be selected are different, this is the same as for the insert settings

of an input channel (➥ p.24).

PM5D Editor Owner’s Manual

❏ EQUALIZER

A EQ graph

Indicates the approximate response for the EQ of the currently selected channel.

B FLAT

If you click this button, the gain of all bands will be reset to 0.00 dB.

C Q

D F (Frequency)

E GAIN

These knobs adjust the Q, center frequency, and boost/cut amount for each band.

F (LOW shelving)

If this button is on, the LOW EQ will be switched to a shelving type (the Q knob of the LOW EQ will disappear).

G HPF (High Pass Filter)

If this button is on, the LOW EQ will function as a high pass ﬁlter EQ. The Q knob of the LOW EQ will disappear,

and the GAIN knob will act as the high pass ﬁlter on/off switch.

H (HIGH shelving)

If this button is on, the HIGH EQ will be switched to a shelving type (the Q knob of the HIGH EQ will disap-

pear).

I LPF (Low Pass Filter)

If this button is on, the HIGH EQ will function as a low pass ﬁlter. The Q knob of the HIGH EQ will disappear,

and the GAIN knob will act as the low pass ﬁlter on/off switch.

J ON (On/off)

Switches the EQ on/off.

K LIBRARY

Accesses the OUTPUT EQ page of the LIBRARY window.

PM5D Editor Owner’s Manual

L TYPE I/TYPE II (EQ type)

Selects either TYPE I (an algorithm equivalent to the EQ in the earlier 02R series) or TYPE II (a newly developed

algorithm) as the EQ type.

M EQ LINK GROUP

Selects the EQ link group (A–F) to which that channel belongs.

N UPPER/LOWER

Switches the four bands affected by controls 3–9 between LOWER (1 LOW–4 HIGH) and UPPER (5 LOW–8

HIGH).

❏ DELAY

This is the same as for the delay settings of an input channel (➥ p.26).

❏ DCA GROUP / MUTE GROUP / SAFE

A DCA GROUP

Selects the DCA group (7/8) to which the MIX channel belongs.

B MUTE GROUP

Selects the mute group (1–8) to which the MIX channel belongs.

C RECALL SAFE / MUTE SAFE

These enable/disable Recall Safe and Mute Safe for the MIX channel.

1 2 3

PM5D Editor Owner’s Manual

❏ Pan / Fader

A TO ST (To stereo)

This is an on/off switch for the signal sent from the MIX channel to the STEREO bus.

The PRE button located below selects PRE (immediately before the MIX [ON] key) or

POST (immediately after the MIX [ON] key) as the point from which the signal is sent

from the MIX channel to the STEREO bus.

B TO ST PAN (To stereo pan)

Sets the panning of the signal sent from the MIX channel to the STEREO bus.

C LCR

Tur ns LCR mode on/off for each channel. If this is turned on for a channel, you can use

the TO ST PAN (

2) knob to simultaneously control the level of the signal sent to the

STEREO bus L/R channels and CENTER channel.

D CSR (Center Side Ratio)

This adjusts the level ratio (0–100%) of the CENTER channel relative to the STEREO

bus L/R channels. To change the value, drag upward or downward inside the numerical

box.

E BALANCE

This adjusts the left/right output balance of paired channels. This is not shown if pair-

ing is not speciﬁed.

F ON

Switches the MIX channel on/off. This is linked with the MIX [ON] keys in the MIX

section of the PM5D panel.

G Fader

Adjusts the output level of the MIX channel. This is linked with the MIX encoders on

the PM5D panel (if the [MIX MASTER] key is on). The current value is shown in the

numerical box immediately below.

H CUE

This button cue-monitors the signal of the MIX channel. This is linked with the MIX

[CUE] keys in the MIX section of the PM5D panel.

PM5D Editor Owner’s Manual

❏ MIX to MATRIX

A MATRIX send level

This adjusts the send level of the signal sent from the MIX channel to the MATRIX buses.

B Pair

This indicates the pairing status of adjacent odd-numbered/even-numbered MATRIX channels. You can click the

heart symbol to enable/disable pairing.

C ON (MATRIX send on/off)

This is an on/off switch for the signal sent from the MIX channel to the MATRIX bus.

D POINT (Send point)

Selects the point from which the signal is sent from the MIX channel to the MATRIX bus. You can choose PRE

FADER (immediately before the fader), POST FADER (immediately after the fader), or POST ON (immediately

after the MIX [ON] key).

E CH to MIX POST POINT

Selects either POST ON or POST TO ST as the position from which the signal is sent from all input channels to

the currently selected MIX bus.

PM5D Editor Owner’s Manual

If a MATRIX channel is selected

❏ CHANNEL SELECT (Channel selection)

Except for the fact that your editing applies to a MATRIX channel, this is the same as for an input channel

(➥ p.20).

❏ COMPRESSOR

Except for the fact that the COMP LINK GROUP is A–F, and that the types of signal that can be selected for key-

in are different, this is the same as for the compressor of an input channel (➥ p.23).

❏ INSERT

Except for the fact that the insert points that can be selected are different, this is the same as for the insert settings

of an input channel (➥ p.24).

❏ EQUALIZER

Except for the fact that there is no LOWER/UPPER button, and that the EQ LINK groups are G/H, this is the

same as for the equalizer of a MIX channel (➥ p.30).

❏ DELAY

This is the same as for the delay settings of an input channel (➥ p.26).

❏ DCA GROUP / MUTE GROUP / SAFE

These are the same as the DCA Group / Mute Group / Safe settings of a MIX channel (➥ p.31).

PM5D Editor Owner’s Manual

❏ Pan / Fader

A BALANCE

This adjusts the left/right output balance of paired channels. This is not shown if pair-

ing is not speciﬁed.

B ON

This switches the MATRIX channel on/off. This is linked with the MATRIX [ON] keys

in the MATRIX section of the PM5D panel.

C Fader

This adjusts the output level of the MATRIX channel. This is linked with the MATRIX

encoders in the MATRIX section of the PM5D panel. The current value is shown in the

numerical box immediately below.

D CUE

This button cue-monitors the signal of the MATRIX channel. This is linked with the

MATRIX [CUE] keys in the MATRIX section of the PM5D panel.

If a STEREO A/B channel is selected

❏ CHANNEL SELECT (Channel selection)

Except for the fact that your editing applies to a STEREO A/B channel, this is the same as the channel selection for

an input channel (➥ p.20).

PM5D Editor Owner’s Manual

❏ COMPRESSOR

Except for the fact that the COMP LINK GROUP is A–F, and that the types of signal that can be selected for key-

in are different, this is the same as for the compressor of an input channel (➥ p.23).

❏ INSERT

Except for the fact that the insert points that can be selected are different, this is the same as for the insert settings

of an input channel (➥ p.24).

❏ EQUALIZER

This is the same as the equalizer settings of a MIX channel (➥ p.30).

❏ DELAY

This is the same as for the delay settings of an input channel (➥ p.26).

❏ DCA GROUP / MUTE GROUP / SAFE

These are the same as the DCA Group / Mute Group / Safe settings of a MIX channel (➥ p.31).

❏ Pan / Fader

A BALANCE

Adjusts the left/right output balance of the STEREO A/B channel.

B ON

This switches the STEREO A/B channel on/off. This is linked with the STEREO [ON]

key in the STEREO A/B channel strip of the PM5D panel.

C Fader

Adjusts the output level of the STEREO A/B channel. This is linked with the STEREO

fader in the STEREO A/B channel strip of the PM5D panel. The current value is shown

in the numerical box immediately below.

D CUE

This button cue-monitors the signal of the STEREO A/B channel. This is linked with

the STEREO [CUE] key in the STEREO A/B channel strip of the PM5D panel.

PM5D Editor Owner’s Manual

❏ STEREO to MATRIX

A MATRIX send level

Here you can adjust the send levels of the signals sent from the STEREO A/B channels to the MATRIX bus.

B Pair

This indicates the pairing status of adjacent odd-numbered/even-numbered MATRIX channels. You can click the

heart symbol to enable/disable pairing.

C ON (MATRIX send on/off)

This is an on/off switch for the signal sent from the STEREO A/B channel to the MATRIX bus.

D POINT (Send point)

Selects the point from which the signal is sent from the STEREO A/B channel to the MATRIX bus. You can choose

PRE FADER (immediately before the fader), POST FADER (immediately after the fader), or POST ON (immedi-

ately after the STEREO [ON] key).

PM5D Editor Owner’s Manual

Here you can assign the input/output port for each channel, its direct output, and its insert-in/out.

This window is divided into INPUT PATCH, OUTPUT PATCH, INPUT INSERT PATCH, OUTPUT INSERT PATCH,

DIRECT OUT PATCH, and PATCH LIST pages. To switch pages, click the tabs shown in the upper part of the window.

INPUT PATCH page

Here you can select the input port that is assigned to the input of each input channel. Except for the fact that you can

resize the window, the basic operation is the same as in the PM5D’s INPUT PATCH screen.

OUTPUT PATCH page

Here you can select the output port that is assigned to the input of each output channel. Except for the fact that you

can resize the window, the basic operation is the same as in the PM5D’s OUTPUT PATCH screen.

Patch Editor window

PM5D Editor Owner’s Manual

INPUT INSERT PATCH page

Here you can assign input/output ports to the insert-in/out of each input channel. Select the output port in the left

side of the screen, and the input port in the right side of the screen. Except for the fact that you can resize the win-

dow, the basic operation is the same as in the PM5D’s INPUT INSERT PATCH screen.

OUTPUT INSERT PATCH page

Here you can assign input/output ports to the insert-in/out of each output channel. Select the output port in the left

side of the screen, and the input port in the right side of the screen. Except for the fact that you can resize the win-

dow, the basic operation is the same as in the PM5D’s OUTPUT INSERT PATCH screen.

PM5D Editor Owner’s Manual

DIRECT OUTPUT PATCH page

Here you can select the output port that will directly output each input channel. Except for the fact that you can

resize the window, the basic operation is the same as in the PM5D’s DIRECT OUTPUT PATCH screen.

PATCH LIST page

Here you can view and edit the input patch and output patch settings. Input patch, output patch, and channel name

data that was written to a CSV ﬁle by the PM5D itself can also be loaded into this page. Conversely, the settings in

this page can be written to a CSV ﬁle that can be loaded into the PM5D.

PM5D Editor Owner’s Manual

A Input channel number

B Input channel name

This is the number and name of the input channel. You can click the channel name box to edit the name in this

page.

C Input port

This shows the input port assigned to the input channel. You can click this box and choose the input port from

the popup menu that appears.

D Output channel number

This is the number of the output channel.

E Output port

This shows the output port assigned to the output channel. You can click this box and choose the output port

from the popup menu that appears.

F IMPORT (Import a CSV ﬁle)

Input patch, output patch, and channel name data from CSV ﬁles written by the PM5D can be loaded into the

PATCH LIST page by clicking this button.

When you click this button, a dialog box will appear as shown at right,

allowing you to specify the folder containing the CSV ﬁles you want to

load.

Specify the folder that contains CSV ﬁles written by the PM5D, and

click the OK button. If the speciﬁed folder contains CSV ﬁles to which

input patch, output patch, and channel name data was written, that

data will be loaded into the PATCH LIST page.

If the speciﬁed folder does not contain the necessary CSV ﬁle,

the settings in the PATCH LIST page will not change. For

example if the folder contains only an input patch CSV ﬁle, only

the input patch settings of the PATCH LIST page will be loaded,

and the remaining settings will not change.

G EXPORT (Export a CSV ﬁle)

By clicking this button, input patch, output patch, and channel name data can be written to a CSV ﬁle that can be

loaded by the PM5D.

When you click this button a dialog box will appear, allowing you to specify a folder for the exported CSV ﬁles.

Specify the folder in which the CSV ﬁles will be saved, and click the OK button. Separate CSV ﬁles containing the

input patch, output patch, and channel name data will be saved in the folder you speciﬁed. You can use a memory

card to load these CSV ﬁles into the PM5D.

1 2 3

4 5

NOTE

PM5D Editor Owner’s Manual

Here you can make surround panning settings for the two currently selected input channels.

A SELECT (Channel selection)

This area displays the name and number of the two channels selected for operations (two adjacent odd-num-

bered/even-numbered input channels, a ST IN channel, or an FX RTN channel). To switch channels, use the

SELECT button or the / buttons at left and right. You can also edit the channel name in the text box.

B PAIR

Indicates the pair status of the two selected channels. If an input channel is selected, you can click the heart sym-

bol to enable/disable pairing.

C LINK

Speciﬁes whether movement of the sound image will be linked for the two selected channels. If this button is on,

the sound image of the two channels will be linked according to the link pattern you select using LINK PATTERN

SELECT buttons 1–8.

D LINK PATTERN SELECT

These buttons select link patterns 1–8. The currently selected pattern is shown graphically at the left.

E SURROUND MODE

This indicates the currently selected surround mode. You can click this area to switch the mode.

Surround Editor window

1 2 3 54

PM5D Editor Owner’s Manual

F DIVERGENCE

These controls specify the proportion at which the signals are sent to each surround bus

when the input channel is positioned in the center. The operable parameters will change as

follows, according to the surround mode that is currently selected.

• Surround mode= 3-1ch/5.1ch

The F knob will be operable, allowing you to adjust the front divergence. Use this knob to

specify the proportion (0–100) at which a signal positioned in the center will be sent to

the center bus (C) and the left/right buses (L, R).

• Surround mode= 6.1ch

The F knob and R knob will be operable, allowing you to adjust the front and rear diver-

gence separately. Use these two knobs to specify the proportion (0–100) at which a signal

positioned in the center will be sent to the center buses (C, S, Bs) and the left/right buses

(L, R, Ls, Rs). In addition, a LINK button that links front and rear divergence is displayed

between the F knob and R knob. If you turn the LINK button on, the value of the F knob

will be copied to the R knob, and the two knobs will be linked.

G LFE (Low Frequency Effect)

Use the LFE knob to adjust the level of the signal sent from the input channel to the subwoofer LFE bus, over a

range of –∞ to 0 dB. The ON/OFF button is an on/off switch for sending to the MIX bus assigned to the LFE

channel.

H Grid

Here you can specify the surround panning of the currently selected input channel, centered on the listening

point. The current setting is indicated by a O symbol. You can drag this symbol up, down, left, or right to move

the panning.

I PANNING buttons

These buttons correspond to each surround bus. Speaker icons are displayed to indicate the surround buses that

are available for the current surround mode.

J SURROUND BUS ON (Surround bus on/off)

These buttons are on/off switches for the signal sent from the currently selected input channel to the correspond-

ing surround bus. You can click the surround bus name buttons at left to move the panning to the position of the

corresponding surround bus.

K PAN POSITION

The surround panning of the currently selected input channel is shown here as front/rear left/right coordinate

values.

PM5D Editor Owner’s Manual

In this window you can select the insertion destination of GEQ modules 1–12, and edit the parameters.

A MODULE (Module selection)

Selects the GEQ module that you want to edit or view.

B INSERT (Insert destination)

Select one of the following as the insert destination for the currently selected GEQ module.

C ON (GEQ on/off)

Switches the currently selected GEQ module on/off.

D LINK

This button links the settings of the adjacent odd-numbered/even-numbered GEQ modules. When you click this

button, a window will appear, asking you to conﬁrm the operation. Click the appropriate button to choose the

source/destination module for the parameters that will be copied. If you click the RESET BOTH button, the

parameters of both modules will be reset to their default value.

E LIBRARY

This button displays the GEQ LIBRARY window.

NONE Not inserted

INS CH1...INS CH48 Input channel 1–48 insert in/out

INS STIN1L, INS STIN1R...INS STIN4R ST IN channel 1–4 (L/R) insert in/out

INS MIX1...INS MIX24 MIX channel 1–24 insert in/out

INS MTX1...INS MTX8 MATRIX channel 1–8 insert in/out

INS STAL, INS STAR STEREO A channel (L/R) insert in/out

INS STBL, INS STBR STEREO B channel (L/R) insert in/out

INS MONL, INS MONR, INS MONC MONITOR channel (L/R/C) insert in/out

GEQ window

2 5431

PM5D Editor Owner’s Manual

F GEQ graph

This graph shows the response of the currently selected GEQ module.

G GEQ faders

These faders cut/boost the frequency bands of the GEQ module. The value of each fader is shown in the numeri-

cal box below it.

H LIMIT

The range and direction of adjustment controlled by the faders can be selected from the following: ±15 dB,

±12 dB, ±6 dB (these are valid in both the boost and cut directions), or –24 dB (valid only in the cut direction).

I EQ FLAT

This button resets all GEQ faders to the 0 dB position.

PM5D Editor Owner’s Manual

Here you can select the effect type for internal effects 1–8, edit the parameters, and specify the input/output patch-

ing.

You can also open multiple Effect Editor windows to simultaneously view the settings of different-num-

bered internal effects. However, the PM5D itself will be linked only with parameter edits performed in the

window you opened ﬁrst. (Parameter edits performed in the PM5D’s own screen will be valid.)

EFFECT No. (Effect number)

Selects the number (1–8) of the internal effect you want to edit.

Alternatively, you can use the Menu bar to choose [Windows] menu

→

[Effect Editor], and select an inter-

nal effect 1–8 from the sub-menu.

EFFECT NAME

Indicates the title of the effect selected for internal effect 1–8.

EFFECT TYPE

Indicates the currently selected effect type. You can also switch the effect type from this window. To do so, click

the text box, and select the desired effect type from the popup menu that appears.

LIBRARY

This button accesses the effect library. Clicking this button will open the EFFECT page of the LIBRARY window.

Effect Editor window

NOTE

2 431

HINT

PM5D Editor Owner’s Manual

E Effect parameters

This area shows the effect parameters and knobs for the

currently selected effect type.

F Input meter

Indicates the level of the signal being input to the internal effect.

G Input patch

Click the L CHANNEL or R CHANNEL area, and choose one of the following as the signal route that will be

patched to the L/R input channels of the internal effect.

If you select INSCH or INSSTIN as the insert-destination, the name of the channel is shown in the box immedi-

ately below.

–– Not inserted

MIX 1...MIX24 Output of MIX channels 1–24

INSCH1...INSCH48 Insert Out of input channels 1–48

INSSTIN1L, INSSTIN1R...INSSTIN4R Insert Out of ST IN channels 1–4 (L/R)

INSMIX1...INSMIX24 Insert Out of MIX channels 1–24

INSMTX1...INSMTX8 Insert Out of MATRIX channels 1–8

INSSTAL, INSSTAR STEREO A channel (L/R) insert out

INSSTAL, INSSTAR STEREO B channel (L/R) insert out

INSMONL, INSMONR, INSMONC MONITOR channel (L/R/C) insert out

PM5D Editor Owner’s Manual

H Output meter

Indicates the level of the signal being output from the internal effect.

I Output patch

Click the L CHANNEL or R CHANNEL area, and choose one of the following as the signal route that will be

patched to the L/R output channels of the internal effect.

If you select CH, STIN, FXRTN, or INSSTIN as the insert-destination, the name of the channel is shown in the

box immediately below.

J GR meter

If “044 M.BAND DYNA” or “045 M.BAND COMP” are selected as the effect type,

this indicates the gain reduction amount for the H (HIGH), M (MID), and L

(LOW) bands.

K SOLO

If “044 M.BAND DYNA” or “045 M.BAND COMP” are selected as the effect type,

these buttons allow you to monitor only the speciﬁed band from the three bands

HIGH, MID, and LOW.

–– Not inserted

CH 1...CH48 Input channel 1–48 input

STIN1L, STIN1R...STIN4R ST IN channel 1–4 (L/R) input

FXRTN1L, FXRTN1R...FXRTN4R FX RTN channel 1–4 (L/R) input

INSCH1...INSCH48 Input channel 1–48 insert in

INSSTIN1L, INSSTIN1R...INSSTIN4R ST IN channel 1–4 (L/R) insert in

INSMIX1...INSMIX24 MIX channel 1–24 insert in

INSMTX1...INSMTX8 MATRIX channel 1–8 insert in

INSSTAL, INSSTAR STEREO A channel (L/R) insert in

INSSTAL, INSSTAR STEREO B channel (L/R) insert in

INSMONL, INSMONR, INSMONC MONITOR channel (L/R/C) insert in

PM5D Editor Owner’s Manual

L MIX BALANCE

Adjusts the balance of the effect sound relative to the original sound. 0 (%) outputs only the original sound, and

100 (%) outputs only the effect sound.

M BYPASS

This button temporarily bypasses the effect.

N CUE

This button cue-monitors the output of the currently selected effect.

O TEMPO

If a tempo-type or modulation-type effect is selected, this allows you to adjust time-related parameters such as

DELAY (delay time) and FREQ. (modulation speed).

To set the value of the TEMPO parameter, you can either input the BPM (Beats Per Minute) in the numerical box,

or repeatedly click the TAP TEMPO button at the desired tempo.

If the MIDI CLK button is on, the TEMPO parameter value will synchronize to the MIDI timing clock being

received from the MIDI port.

P PLAY/REC (Play/Record) buttons

If “042 FREEZE” is selected as the effect type, you can use these buttons to record and play back the signal being

input to the effect.

LNM

PM5D Editor Owner’s Manual

In this window you can select the channels that will be assigned to each DCA group and mute group. This window is

divided into two pages; the DCA GROUP ASSIGN page and the MUTE GROUP ASSIGN page.

DCA GROUP ASSIGN page

Here you can specify the channels that will be assigned to DCA groups 1–8. The upper part of the screen lets you

assign input channels to DCA groups, and the lower part of the screen lets you assign output channels to DCA

groups.

Except for the fact that assignments for both input channels and output channels can be made in a single screen, and

the fact that the screen can be resized vertically and horizontally, basic operation here is the same as in the PM5D’s

DCA GROUP ASSIGN screen.

A DCA group

This is the number of the DCA group.

B DCA group name

This is the name of the DCA group. You can also click the mouse on this area to edit the name.

DCA/Mute Group window

1 2 3 4

PM5D Editor Owner’s Manual

C Grid

This grid lets you assign channels (horizontal rows) to DCA groups (vertical columns). Currently-patched grids

are indicated by a symbol. To enable or disable an assignment, click the desired grid.

D CLEAR

These buttons clear all input channels and output channels assigned to the corresponding DCA group. When you

click one of these buttons a window will appear, asking you to conﬁrm the operation. To execute the Clear opera-

tion, click the OK button.

Clicking the CLEAR button for input channel DCA groups 7/8 will not affect the output channel assignments.

(The converse also applies.)

MUTE GROUP ASSIGN page

Here you can specify the channels that will be assigned to mute groups 1–8. The upper part of the screen lets you

assign input channels to mute groups, and the lower part of the screen lets you assign output channels to mute

groups.

Except for the fact that assignments for both input channels and output channels can be made in a single screen, and

the fact that the screen can be resized vertically and horizontally, basic operation here is the same as in the PM5D’s

MUTE GROUP ASSIGN screen.

PM5D Editor Owner’s Manual

A Mute group

This area shows the mute group number.

B MUTE MASTER (Mute master)

These buttons enable/disable each input channel or output channel mute group.

C Grid

This grid lets you assign channels (horizontal rows) to mute groups (vertical columns). Currently-patched grids

are indicated by a symbol. To enable or disable an assignment, click the desired grid.

D MUTE SAFE ON (Mute Safe on/off)

These buttons switch Mute Safe on/off for each channel. Channels for which this button is on will be excluded

from mute groups.

E CLEAR

These buttons clear all input channels and output channels assigned to the corresponding mute group. When you

click one of these buttons a window will appear, asking you to conﬁrm the operation. To execute the Clear opera-

tion, click the OK button.

1 2 3 5

PM5D Editor Owner’s Manual

Here you can manage scene memories, and make various settings related to scene recall operations.

This window is divided into SCENE MEMORY, EVENT LIST, RECALL SAFE, and FADE TIME pages. To switch

pages, click the tabs shown in the upper part of the window.

SCENE MEMORY page

Here you can edit the PM5D’s scene memories. You can also load scene library ﬁles from a memory card or from a

drive of your computer, and edit them. In this case, you can re-save all scenes to a ﬁle after editing, recall just a

desired scene, or copy a desired scene to the scene memory of the PM5D itself.

A OPEN (Open a ﬁle)

Opens a scene library ﬁle located on a drive of

your computer.

B CLOSE (Close a ﬁle)

Closes the currently-open scene library ﬁle.

C SAVE

Saves the currently-open scene library ﬁle on a

drive of your computer.

D SAVE AS (Save as a different

name)

Saves the currently-open scene library ﬁle under

a different name on a drive of your computer.

E File name

Indicates the ﬁle name of the currently-open

scene library.

Scene window

3 4

PM5D Editor Owner’s Manual

F FILE

This area lists the scenes in the ﬁle you opened using the OPEN button (1). The list includes the following items.

To view items that are not currently shown, scroll the list to the right. The boundary lines in the center of

the window can be dragged toward the right to expand the ﬁle list display area as shown below.

G No. (Scene number)

This is the scene number 000–500.

H TITLE

This is the scene title. You can also double-click this area and edit the title.

I PROTECT

Tur ns the protection setting on/off for each scene. This area displays a lock icon for protected scenes; these scenes

cannot be overwritten, nor their title edited. Read-only scenes are indicated by “READ” displayed in this column.

J SEL. RECALL (Selective recall)

Switches the selective recall setting on/off for each scene. Selective recall using Safe parameters is enabled for

scenes for which this column indicates “SAFE,” and selective recall using Recall parameters is enabled for scenes

for which this column indicates “RECALL.”

K Library link

These columns indicates the number and title of the INPUT PATCH library, OUTPUT PATCH library, and HA

library that are linked to each scene. (With the default column width of the list, only the library number is

shown.) You can click the numerical area and specify the linked library from the popup menu that appears.

L COMMENT

This column shows the comment assigned to each scene. You can also double-click this column and edit the com-

ment.

M TIME STAMP

Indicates the time at which the scene was last stored, in the format of month/day/year/hours/minutes/seconds.

This column is only for display, and cannot be edited.

N MIDI EVENT

In this column, the MIDI event that is transmitted from the MIDI OUT connector when the scene is recalled can

be viewed and edited in hexadecimal form. To edit a MIDI event, click the two-digit hexadecimal value you want

to edit, and choose the desired value from the popup menu that appears.

• If you choose “NOP” from the popup menu, that two-digital hexadecimal value will be ignored.

• If you choose “END” from the popup menu, all subsequent hexadecimal values will be ignored.

HINT

7 8 9 J K

L M N

HINT

PM5D Editor Owner’s Manual

O TX (MIDI event transmission)

If you click this column to make the “TX” indication appear, transmission will be enabled for the MIDI event

speciﬁed for this scene.

P GPI OUT CONTROL

Speciﬁes the polarity (high-active/low-active) and transmission method (tally/trigger) of the signal that is sent

from GPI OUT ports 1–12 when the scene is recalled. You can also click these columns to edit the setting. You can

choose from the following settings.

Q REMOTE TRANSPORT

These columns indicate the MMC/RS422 transport command that will be executed when you recall the scene.

The left column indicates the protocol (MMC or RS422), and the right column indicates the type of command.

You can click an item and choose the desired protocol or command from the popup menu that appears.

R INTERNAL DATA

This area shows the PM5D’s scene memory contents. The items displayed are the same as in the FILE list (6).

As desired, you can copy single or multiple scenes between the FILE list and the INTERNAL DATA list, and copy

or move them to a different location within a list.

To do this, use the following methods to select the scene(s) that you want to copy or move.

Display Polarity Transmission method

None Disabled

High active Tally

Low active Tally

High active Trigger

Low active Trigger

O P Q

PM5D Editor Owner’s Manual

•To select a single scene

Click the line containing the desired scene.

•To select multiple consecutive scenes

Click the ﬁrst scene to select it; then hold down the <Shift> key and

click the last scene.

•To select multiple non-consecutive scenes

Click the ﬁrst scene; then hold down the <Ctrl> key ( key) and

click each of the remaining scenes.

When you have selected the scene(s) that you want to move or copy,

drag them to the desired location in the other list (if you’re copying

between lists) or in the same list (if you’re copying/moving within the

same list).

•To copy scenes (overwriting the destination)

Drag the copy-source scene(s) to the desired line in the other list or to

another line in the same list. At this time, a

symbol will appear at

the right of the scene number.

When you release the mouse in this state, a dialog box will appear,

asking you to conﬁrm the Save operation. If you click the OK button,

the copy-source scene(s) will be overwritten onto the copy-destina-

tion scenes, and the copy-source scene(s) will remain unchanged. (If

the copy-source selection contains multiple scenes, the data will be overwritten onto consecutive scenes start-

ing at that scene.)

•To move scenes

Within the same list, you can move the selected scene(s) to another

location to rearrange the order of the scenes in the list. To do this,

drag the selected scene(s) to a location between two other lines in the

same list. At this time, a symbol will appear between the lines.

When you release the mouse button in this state, the selected scene(s)

will move to that location, and the scene numbers will also change

accordingly. (If the move-source selection contains multiple scenes,

those scenes will be inserted consecutively at the location you specify.)

STORE

Stores the current settings to the scene that is selected in the list.

RECALL

Recalls the settings of the scene selected in the list.

CLEAR

Clears the scene(s) selected in the list. (The title of the cleared scene(s) will be reset to [ No Data! ].)

UNDO

Cancels the last-performed scene recall, store, copy, or move operation.

PROTECT

Tur ns on the Protect setting for the scene(s) selected in the list.

PM5D Editor Owner’s Manual

EVENT LIST page

In this page you can see how the scenes registered in the PM5D’s EVENT LIST screen will be switched according to

the progression of time code or according to the elapsed time since the most recent Recall operation.

• This page functions as a viewer of the PM5D’s EVENT LIST screen. You cannot register or recall

events from within this page.

• In order for the EVENT LIST page to be synchronized with the EVENT LIST screen of the PM5D itself,

PM5D Editor must be synchronized with the PM5D.

A No. (Number)

This column indicates the number of each event registered in the event list.

B EVENT TRIGGER

This column indicates the recall condition speciﬁed for each event. This shows an hour:minute:second:frame

value for scenes that will be recalled at a speciﬁc time code, a value in seconds for scenes that are recalled after a

speciﬁed time has elapsed after the preceding event was executed, or [MANUAL] for scenes that are recalled man-

ually.

C SCENE TITLE

This column indicates the number and title of the scene that will be recalled.

NOTE

1 2 3

PM5D Editor Owner’s Manual

RECALL SAFE page

Here you can make settings for the Recall Safe function that excludes only speciﬁc channels from recall operations of

all scenes.

Except for the fact that there is no PASTE button for copying and pasting parameter settings from the SELECTIVE

RECALL screen, the display and operations within this page are the same as in the PM5D’s RECALL SAFE screen.

FADE TIME page

Here you can make settings for the Fade function that adjusts the time over which fader and pan will reach their new

values when a scene is recalled. The settings of the Fade function are independent for each scene.

PM5D Editor Owner’s Manual

A FADING ENABLE (Fade function enable/disable)

Switches the Fade function for fader levels between enabled and disabled.

B INPUT CHANNEL PANNING ENABLE (Input channel panning enable/disable)

Switches the Fade function for input channel pan (balance) parameters between enabled and disabled. If this but-

ton is on, you can use the two buttons located at the right to select the input channels to which this setting will

apply.

• When the ALL INPUT CHANNEL button is on

The Fade function will apply to the pan (balance) parameter of all input channels.

• When the SAME AS FADING button is on

The Fade function will apply to the pan (balance) parameter of input channels for which the Fade function is

turned on in

C SET ALL

This button lets you enable all Fade function settings with one click. This can be operated independently for all

input channels and DCA groups, or for all output channels.

D CLEAR ALL

This button lets you disable all Fade function settings with one click. This can be operated independently for all

input channels and DCA groups, or for all output channels.

E Channel settings

Here you can specify the Fade function on/off status, the fade time, and the

offset time for each input channel, output channel, and DCA group.

To edit the fade time or offset time value, click the numerical box and drag

upward or downward.

1 2

3 4

Fade time

Offset time

Fade on/off

PM5D Editor Owner’s Manual

Here you can edit the PM5D’s various libraries. You can also load library ﬁles that were saved on a drive of your com-

puter, edit the order or title of library items, recall the desired library data, or copy desired library data to a library

within the PM5D.

This window is divided into INPUT CH, OUTPUT CH, GATE, COMP, INPUT EQ, OUTPUT EQ, INPUT PATCH,

OUTPUT PATCH, EFFECT, GEQ, and HA pages; to switch pages, click the tabs located at the top of the window. The

editing procedure is the same in all pages. The explanation here uses the example of the INPUT CH page.

A OPEN (Open a ﬁle)

Opens a library ﬁle located on a drive of your

computer. Use this when you want to edit

library data that you’ve saved on a memory card.

B CLOSE (Close a ﬁle)

Closes the currently-open library ﬁle.

C SAVE

Saves the currently-open library ﬁle on a drive of

your computer. Use this to re-save an edited

library on a memory card, or to create a backup

on the hard disk of your computer.

D SAVE AS (Save under a different

name)

Saves the currently-open library ﬁle under a dif-

ferent name on a drive of your computer.

E File name

Indicates the ﬁle name of the currently-open

library.

F FILE

This list shows the contents of the data in the library ﬁle you opened using the OPEN button (1). The list

includes the following items.

Library window

3 4

PM5D Editor Owner’s Manual

No. (Number)

This column indicates the number of each item in the library.

TITLE

This column indicates the title assigned to each library item. You can also double-click this area and edit the title.

PROTECT

This indicates the Protect setting on/off. This area displays a lock icon for protected data; this data cannot be over-

written, nor its title edited. Read-only data is indicated by “READ” displayed in this column.

INTERNAL DATA

This area shows the PM5D’s library contents. The items displayed are the same as in the FILE list (

As desired, you can copy single or multiple items between the FILE list and the INTERNAL DATA list, and copy

or move them to a different location within a list. The procedure is the same as in the SCENE MEMORY page of

the Scene window (

➥

p.55).

STORE

Stores the current settings to the data item that is selected in the list.

RECALL

Recalls the data item that is selected in the list.

CLEAR

Clears the data item(s) selected in the list. (The title of the cleared item(s) will be reset to [ No Data! ].)

UNDO

Cancels the last-performed library recall, store, copy, or move operation.

7 8 9

PM5D Editor Owner’s Manual

Here you can view the signal levels within the PM5D, or the amount of gain reduction produced by the internal compres-

sors and gates. This lets you check signal presence, overload status, and compressor/gate operation from your computer.

This window is divided into INPUT METER, OUTPUT METER, INPUT GR, and OUTPUT GR pages. To switch

pages, click the tabs shown in the upper part of the window.

The displayed content and operation in each page is the same as the various screens of the PM5D’s METER function.

In order to view the PM5D’s signal levels in the Meter window, make sure that PM5D Editor and the PM5D

itself are synchronized.

This window displays the time code (LTC, MTC) that the PM5D itself is

receiving or generating, in units of hours/minutes/seconds/frames. This

is the same time code as displayed in the PM5D’s ﬁxed display screen and

in the EVENT LIST screen.

In order for the Timecode Counter window to display the time code that the PM5D itself is receiving/gen-

erating, PM5D Editor and the PM5D must be synchronized.

Synchronization between the PM5D itself and PM5D Editor can be switched on/off in

this window. This has the same function as the [Synchronization] menu. Click the

ONLINE button to switch to off-line, or click the OFFLINE button to switch to on-line.

If you click the RE-SYNC button, the Synchronization dialog box will appear (➥ p.3).

The current scene number is also displayed in this window.

Meter window

NOTE

Timecode Counter window

NOTE

Sync window

PM5D Editor Owner’s Manual

Menu Action Windows Macintosh

File menu

Creates a new Session Ctrl+N

Opens a previously saved Session Ctrl+O

Saves the current Session Ctrl+S

Edit menu

Undo Ctrl+Z

Redo Ctrl+Y

Windows menu

Closes the active window Ctrl+W

Closes all windows Ctrl+Alt+W

+Option+W

Opens the Sync window Ctrl+1

Opens the INPUT CH (CH1-24) window Ctrl+2

Opens the INPUT CH (CH25-48) window Ctrl+Alt+2

+Option+2

Opens the Selected Channel window Ctrl+3

Opens the Library window Ctrl+4

Opens the Patch Editor window Ctrl+5

Opens the Surround Editor window Ctrl+6

Opens the Timecode Counter window Ctrl+7

Opens the Effect Editor window Ctrl+8

Opens the Meter window Ctrl+9

Opens the GEQ Editor window Ctrl+0

Opens the DCA/Mute Group window Ctrl+Alt+1

+Option+1

Opens the Scene window Ctrl+Alt+3

+Option+3

Library window or

SCENE MEMORY page

of the Scene window

Selects consecutive multiple items (memories) Shift+click shift+click

Selects non-consecutive multiple items (memories) Ctrl+click

+click

Selects all memories in a section Ctrl+A

Keyboard Shortcuts

PM5D Editor Owner’s Manual

ALL INPUT CHANNEL ................ 59

Bus Setup .......................................... 3

BYPASS .......................................... 49

CH to MIX ..................................... 28

Channel to mix .............................. 28

CLEAR ...................................... 56, 61

CLEAR ALL .................................... 59

CLOSE ...................................... 53, 60

COMMENT ................................... 54

CSV file

Export ....................................... 41

Import ...................................... 41

Ctrl ( ) + click ................................ 5

Ctrl ( ) +Shift+Click ..................... 5

DCA fader ...................................... 19

DCA group ..................................... 50

DCA GROUP ASSIGN page ......... 50

DCA window ................................. 19

DCA/MUTE GROUP window

DCA GROUP ASSIGN page ... 50

MUTE GROUP ASSIGN page 51

DCA/Mute Group window ........... 50

DIRECT OUTPUT PATCH page .40

DIVERGENCE ............................... 43

Effect

GR meter .................................. 48

SOLO ........................................ 48

Effect Editor window ..................... 46

Effect parameters ........................... 47

EFFECT TYPE ............................... 46

EQ FLAT ........................................ 45

EVENT LIST page .......................... 57

EVENT TRIGGER ......................... 57

EXPORT ......................................... 41

Fade ................................................ 58

Fade function enable/disable ......... 59

FADE TIME page ........................... 58

FADING ENABLE ......................... 59

FILE .......................................... 54, 60

File

Close ....................................53, 60

Open ....................................53, 60

FX RTN window ............................ 11

GEQ faders ..................................... 45

GEQ graph ..................................... 45

GEQ window ................................. 44

GPI OUT CONTROL ................... 55

IMPORT ........................................ 41

INPUT CH window ........................ 6

INPUT CHANNEL PANNING

ENABLE .......................... 59

Input channel panning enable/

disable ............................. 59

INPUT INSERT PATCH page ...... 39

INPUT PATCH page ..................... 38

INTERNAL DATA ...................55, 61

Keyboard Shortcuts ....................... 63

LFE ................................................. 43

Library link .................................... 54

Library window ............................. 60

LIMIT ............................................. 45

LINK PATTERN SELECT ............. 42

Low Frequency Effect .................... 43

MATRIX window .......................... 15

Meter window ................................ 62

MIDI EVENT ................................ 54

MIDI event transmission .............. 55

MIX BALANCE ............................. 49

MIX to MATRIX ........................... 33

MIX window .................................. 13

MODULE ...................................... 44

Mute group .................................... 52

MUTE GROUP ASSIGN page ...... 51

MUTE MASTER ............................ 52

MUTE SAFE ON/OFF .................. 52

Offline Edit ...................................... 3

OPEN ........................................53, 60

OUTPUT INSERT PATCH page .. 39

OUTPUT PATCH page ................ 38

Pair Mode .........................................3

Pan Nominal Position ......................3

PAN POSITION .............................43

Patch Editor window .....................38

DIRECT OUTPUT PATCH page

........................................40

INPUT INSERT PATCH page .39

INPUT PATCH page ...............38

OUTPUT INSERT PATCH page

........................................39

OUTPUT PATCH page ...........38

PATCH LIST page ....................40

PATCH LIST page ..........................40

PLAY/REC ......................................49

PROTECT ..........................54, 56, 61

RECALL ....................................56, 61

Recall Safe .......................................58

RECALL SAFE page .......................58

REDO ................................................5

REMOTE TRANSPORT ................55

Re-synchronize .................................3

SAME AS FADING ........................59

SAVE .........................................53, 60

SAVE AS ...................................53, 60

Save as a different name ...........53

Save under a different name ....60

SCENE MEMORY page .................53

Scene window .................................53

EVENT LIST page ....................57

FADE TIME page .....................58

RECALL SAFE page .................58

SCENE MEMORY page ...........53

SEL ..................................................54

SEL. RECALL .................................54

Selected Channel window ..............20

Channel selection .....................20

Channel to mix .........................28

COMPRESSOR ........................23

DCA GROUP / MUTE GROUP /

SAFE ........................26, 31

DELAY ......................................26

EQUALIZER .......................25, 30

GATE ........................................21

HA gain/phase/high-pass filter 21

Input channel ...........................20

INSERT .....................................24

M/S DECODE ..........................26

MATRIX channel .....................34

MIX channel .............................29

MIX to MATRIX ......................33

Index

PM5D Editor Owner’s Manual

Pan / Fader ............. 27, 32, 35, 36

STEREO A/B channel .............. 35

STEREO to MATRIX ............... 37

Selective recall ................................ 54

Sessions ............................................ 4

SET ALL ......................................... 59

Setup

Console ....................................... 3

System ........................................ 2

ST IN window .................................. 9

Stereo B ............................................ 3

STEREO to MATRIX .................... 37

STEREO window ........................... 17

STORE ...................................... 56, 61

Surround Bus Allocation ................. 3

SURROUND BUS ON/OFF .......... 43

Surround Editor window .............. 42

Surround Mode ......................... 3, 42

Sync window .................................. 62

Synchronize ...................................... 3

Tabs .................................................. 4

TEMPO .......................................... 49

TIME STAMP ................................ 54

Timecode Counter window .......... 62

TX ................................................... 55

UNDO .................................. 5, 56, 61

Yamaha Pro Audio Global Site ....... 1

Yamaha PM5D/PM5D-RH, PM5D de handleiding

Gerelateerde papieren