Simplicity 12S502-0810-E1 Handleiding

Merk: Simplicity

Model: 12S502-0810-E1

Categorie: Accessoires voor motorvoertuigen

Type: Handleiding

English

es fr

Español Français

deda el it nonl pt svfi

Dansk Norsk SvenskaDeutsch Suomi NederlandsItaliano

ÅëëçíéêÜ

Português

Operator’s Manual

Betjeningsvejledning

Bedienungsanleitung

Åã÷åéñßäéï ×ñÞóçò

Manual del Operario

Käyttäjän käsikirja

Manuel de l’opérateur

Manuale dell’Operatore

Gebruiksaanwijzing

Brukerhåndbok

Manual do Operador

Instruktionsbok

Form No. 277102WST

Revision: D

E 2009 Briggs & Stratton Corporation,

Briggs & Stratton is a registered trademark

of Briggs & Stratton Corporation

Model 120000

Intekt 825/850/875 Seriest

Intekt Edge 825/850 Seriest

Intekt Pro 825 Seriest

Not for Reproduction

BRIGGSandSTRATTON.COM

4 5

Not for Reproduction

4 BRIGGSandSTRATTON.COM

General Information

For replacement parts or technical assistance, record below the engine model, type, and

code numbers along with the date of purchase. These numbers are located on your

engine (see the Features and Controls page).

Date of purchase:

Engine model:

MM/DD/YYYY

Model: Code:Ty pe:

Engine Power Rating Information

The gross power rating for individual gas engine models is labeled in accordance with

SAE (Society of Automotive Engineers) code J1940 (Small Engine Power & Torque

Rating Procedure), and rating performance has been obtained and corrected in

accordance with SAE J1995 (Revision 2002-05). Torque values are derived at 3060

RPM; horsepower values are derived at 3600 RPM. Actual gross engine power will be

lower and is affected by, among other things, ambient operating conditions and

engine-to-engine variability. Given both the wide array of products on which engines are

placed and the variety of environmental issues applicable to operating the equipment,

the gas engine will not develop the rated gross power when used in a given piece of

power equipment (actual “on-site” or net power). This difference is due to a variety of

factors including, but not limited to, accessories (air cleaner, exhaust, charging, cooling,

carburetor, fuel pump, etc.), application limitations, ambient operating conditions

(temperature, humidity, altitude), and engine-to-engine variability. Due to manufacturing

and capacity limitations, Briggs & Stratton may substitute an engine of higher rated

power for this Series engine.

Operator Safety

Explosion

Toxic Fumes

Moving Parts

Shock

Hot Surface

Kickback

Fire

Fuel Shutoff

Read Manual

Choke

Oil

Fuel

On Off

Stop

Wear Eye

Protection

Slow

Fast

SAFETY AND CONTROL SYMBOLS

Hazardous

Chemical

Frostbite

The safety alert symbol is used to identify safety information about hazards that can

result in personal injury. A signal word (DANGER, WARNING, or CAUTION) is used with the

alert symbol to indicate the likelihood and the potential severity of injury . In addition, a hazard

symbol may be used to represent the type of hazard.

DANGER indicates a hazard which, if not avoided, will result in death or

serious injury.

WARNING indicates a hazard which, if not avoided, could result in death or

serious injury.

CAUTION indicates a hazard which, if not avoided, could result in minor or

moderate injury.

NOTICE indicates a situation that could result in damage to the product.

WARNING

Certain components in this product and its related accessories contain chemicals

known to the State of California to cause cancer, birth defects, or other reproductive

harm. Wash hands after handling.

WARNING

The engine exhaust from this product contains chemicals known to the State of

California to cause cancer, birth defects, or other reproductive harm.

WARNING

Briggs & Stratton does not approve or authorize the use of these engines on 3-wheel

All Terrain Vehicles (ATVs), motor bikes, fun /recreational go-karts, aircraft products,

or vehicles intended for use in competitive events. Use of these engines in such

applications could result in property damage, serious injury (including paralysis), or

even death.

NOTICE: This engine was shipped from Briggs & Stratton without oil. Before you start

the engine, make sure you add oil according to the instructions in this manual. If you

start the engine without oil, it will be damaged beyond repair and will not be covered

under warranty.

WARNING

Fuel and its vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

When Adding Fuel

• Turn engine off and let engine cool at least 2 minutes before removing the fuel

cap.

• Fill fuel tank outdoors or in well-ventilated area.

• Do not overfill fuel tank. To allow for expansion of the fuel, do not fill above the

bottom of the fuel tank neck.

• Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition

sources.

• Check fuel lines, tank, cap, and fittings frequently for cracks or leaks.

Replace if necessary

• If fuel spills, wait until it evaporates before starting engine.

When Starting Engine

• Ensure that spark plug, muffler, fuel cap and air cleaner (if equipped) are in

place and secured.

• Do not crank engine with spark plug removed.

• If engine floods, set choke (if equipped) to OPEN/RUN position, move throttle

(if equipped) to FAST position and crank until engine starts.

When Operating Equipment

• Do not tip engine or equipment at angle which causes fuel to spill.

• Do not choke the carburetor to stop engine.

• Never start or run the engine with the air cleaner assembly (if equipped) or the

air filter (if equipped) removed.

When Changing Oil

• If you drain the oil from the top oil fill tube, the fuel tank must be empty or fuel

can leak out and result in a fire or explosion.

When Transporting Equipment

• Transport with fuel tank EMPTY or with fuel shut-off valve OFF.

When Storing Fuel Or Equipment With Fuel In Tank

• Store away f rom furnaces, stoves, water heaters or other appliances that have

pilot lights or other ignition sour ces because they can ignite fuel vapors.

Starting engine creates sparking.

Sparking can ignite nearby flammable gases.

Explosion and fire could result.

WARNING

• If there is natural or LP gas leakage in area, do not start engine.

• Do not use pressurized starting fluids because vapors are flammable.

Engines give off carbon monoxide, an odorless, colorless, poison gas.

Breathing carbon monoxide can cause nausea, fainting or death.

WARNING

• Start and run engine outdoors.

• Do not start or run engine in enclosed area, even if doors or windows are open.

Not for Reproduction

Rapid retraction of starter cord (kickback) will pull hand and arm

toward engine faster than you can let go.

Broken bones, fractures, bruises or sprains could result.

WARNING

• When starting engine, pull the starter cord slowly until resistance is felt and then

pull rapidly to avoid kickback.

• Remove all external equipment/engine loads before starting engine.

• Direct-coupled equipment components such as, but not limited to, blades,

impellers, pulleys, sprockets, etc., must be securely attached.

Rotating parts can contact or entangle hands, feet, hair, clothing, or

accessories.

Traumatic amputation or severe laceration can result.

WARNING

• Operate equipment with guards in place.

• Keep hands and feet away from rotating parts.

• Tie up long hair and remove jewelry.

• Do not wear loose-fitting clothing, dangling drawstrings or items that could

become caught.

Running engines produce heat. Engine parts, especially muffler,

become extremely hot.

Severe thermal burns can occur on contact.

Combustible debris, such as leaves, grass, brush, etc. can catch fire.

WARNING

• Allow muffler, engine cylinder and fins to cool before touching.

• Remove accumulated debris from muffler area and cylinder area.

• It is a violation of California Public Resource Code, Section 4442, to use or

operate the engine on any forest-covered, brush-covered, or grass-covered land

unless the exhaust system is equipped with a spark arrester, as defined in

Section 4442, maintained in effective working order. Other states or federal

jurisdictions may have similar laws. Contact the original equipment

manufacturer, retailer, or dealer to obtain a spark arrester designed for the

exhaust system installed on this engine.

Unintentional sparking can result in fire or electric shock.

Unintentional start-up can result in entanglement, traumatic

amputation, or laceration.

Fire hazard

WARNING

Before performing adjustments or repairs:

• Disconnect the spark plug wire and keep it away from the spark plug.

• Disconnect battery at negative terminal (only engines with electric start.)

• Use only correct tools.

• Do not tamper with governor spring, links or other parts to increase engine

speed.

• Replacement parts must be the same and installed in the same position as the

original parts.

• Do not strike the flywheel with a hammer or hard object because the flywheel

may later shatter during operation.

When testing for spark:

• Use approved spark plug tester.

• Do not check for spark with spark plug removed.

Not for Reproduction

6 BRIGGSandSTRATTON.COM

Features and Controls

Compare the illustration

with your engine to familiarize yourself with the location of

various features and controls.

A. Engine Identification

Model Type Code

B. Spark Plug

C. Primer (optional)

D. Fuel Tank and Cap

E. Air Cleaner

F. Starter Cord Handle

G. Dipstick

H. Oil Drain Plug

I. Muffler

Muffler Guard (optional)

Spark Arrester (optional)

J. Choke (optional)

K. Throttle Control (optional)

L. Stop Switch (optional)

M. Shut-off Valve (optional)

N. Fuel Filter (optional)

O. Finger Guard

P. Oil Filter (optional)

Operation

Oil capacity (see the Specifications section)

Oil Recommendations

We recommend the use of Briggs & Stratton Warranty Certified oils for best

performance. Other high-quality detergent oils are acceptable if classified for service SF,

SG, SH, SJ or higher. Do not use special additives.

Outdoor temperatures determine the proper oil viscosity for the engine. Use the chart to

select the best viscosity for the outdoor temperature range expected.

* Below 40°F(4°C) the use of SAE 30 will result in hard starting.

** Above 80°F(27°C) the use of 10W-30 may cause increased oil consumption. Check

oil level more frequently.

How To Check/Add Oil - Figure

Before adding or checking the oil

• Place engine level.

• Clean the oil fill area of any debris.

1. Remove the dipstick (G) and wipe with a clean cloth (Figure 2).

2. Insert and tighten the dipstick.

3. Remove the dipstick and check the oil level. It should be at the top of t he full indicator

(J) on the dipstick.

4. If low, add oil s lowly into the engine oil fill ( H). Do not overfill. After adding oil, wait

one minute and then recheck t he oil level.

5. Replace and tighten the dipstick.

Fuel Recommendations

Fuel must meet these requirements:

• Clean, fresh, unleaded gasoline.

• A minimum of 87 octane/87 AKI (91 RON). High altitude use, see below.

• Gasoline with up to 10% ethanol (gasohol) or up to 15% MTBE (methyl tertiary

butyl ether) is acceptable.

CAUTION: Do not use unapproved gasolines, such as E85. Do not mix oil in gasoline or

modify the engine to run on alternate fuels. This will damage the engine components and

void the engine warranty.

To protect the fuel system from gum formation, mix a fuel stabilizer into the fuel. See

Storage. All fuel is not the same. If starting or performance problems occur, change fuel

providers or change brands. This engine is certified to operate on gasoline. The

emissions control system for this engine is EM (Engine Modifications).

High Altitude

At altitudes over 5,000 feet (1524 meters), a minimum 85 octane/85 AKI (89 RON)

gasoline is acceptable. To remain emissions compliant, high altitude adjustment is

required. Operation without this adjustment will cause decreased performance,

increased fuel consumption, and increased emissions. See a Briggs & Stratton

Authorized Dealer for high altitude adjustment information.

Operation of the engine at altitudes below 2,500 feet (762 meters) with the high altitude

kit is not recommended.

How To Add Fuel - Figure

WARNING

Fuel and its vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

When Adding Fuel

• Turn engine off and let engine cool at least 2 minutes before removing the fuel

cap.

• Fill fuel tank outdoors or in well-ventilated area.

• Do not overfill fuel tank. To allow for expansion of the fuel, do not fill above the

bottom of the fuel tank neck.

• Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition

sources.

• Check fuel lines, tank, cap, and fittings frequently for cracks or leaks.

Replace if necessary

• If fuel spills, wait until it evaporates before starting engine.

1. Clean the fuel cap area of dirt and debris. Remove the fuel cap (A, Figure 3).

2. Fill the fuel tank (B) with fuel. To allow for expansion of the fuel, do not fill above the

bottom of the fuel tank neck (C).

3. Reinstall the fuel cap.

How To Start The Engine

Rapid retraction of starter cord (kickback) will pull hand and arm

toward engine faster than you can let go.

Broken bones, fractures, bruises or sprains could result.

WARNING

• When starting engine, pull the starter cord slowly until resistance is felt and then

pull rapidly to avoid kickback.

WARNING

Fuel and its vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

When Starting Engine

• Ensure that spark plug, muffler, fuel cap and air cleaner (if equipped) are in

place and secured.

• Do not crank engine with spark plug removed.

• If engine floods, set choke (if equipped) to OPEN/RUN position, move throttle

(if equipped) to FAST position and crank until engine starts.

Engines give off carbon monoxide, an odorless, colorless, poison gas.

Breathing carbon monoxide can cause nausea, fainting or death.

WARNING

• Start and run engine outdoors.

• Do not start or run engine in enclosed area, even if doors or windows are open.

NOTICE: This engine was shipped from Briggs & Stratton without oil. Before you start

the engine, make sure you add oil according to the instructions in this manual. If you

start the engine without oil, it will be damaged beyond repair and will not be covered

under warranty.

Not for Reproduction

Determine The Starting System

Before starting the engine, you must determine the type of starting system that is on your

engine. Your engine will have one of the following types.

• ReadyStart

System: This features a temperature controlled automatic choke. It

does not have a manual choke or a primer.

• Primer System: This features a red primer to be used for starting in cool

temperatures. It does not have a manual choke.

• Choke System: This features a choke to be used for starting in cool temperatures.

Some models will have a separate choke lever while others will have a combination

choke/ throttle lever. This type does not have a primer.

To start your engine, follow the instructions for your type of starting system.

Note: Some engines and equipment have remote controls. See the equipment manual

for location and operation of remote controls.

ReadyStart

System - Figure

4 5

1. Check the oil level. See the How To Check/Add Oil section.

2. Make sure equipment drive controls, if equipped, are disengaged.

3. Push the stop switch (A), if equipped, to the on position (Figure 4).

4. Turn the fuel shut-off valve (B), if equipped, to the on position.

5. Move the throttle control (C)tothefast

position. Operate the engine in the fast

position.

6. If the product is equipped with an engine stop lever (D), hold the engine stop lever

against the handle (Figure 5).

7. Rewind Start: Firmly hold the starter cord handle (E). Pull the starter cord handle

slowly until resistance is felt, then pull rapidly (Figure 4).

Note: If the engine does not start after repeated attempts, go to

BRIGGSandSTRATTON.COM or call 1-800-233-3723 (in USA).

WARNING: Rapid retraction of the starter cord (kickback) will pull your

hand and arm toward the engine faster than you can let go. Broken bones, fractures,

bruises or sprains could result. When starting engine, pull the starter cord slowly until

resistance is f elt and then pull rapidly to avoid kickback.

8. Electric Start: Turn the electric start switch to the on /start position.

Note: If the engine does not start after repeated attempts, go to

BRIGGSandSTRATTON.COM or call 1-800-233-3723 (in USA).

NOTICE: To extend the life of the starter, use short starting cycles (five seconds

maximum). Wait one minute between starting cycles.

Primer System - Figure

4 5

1. Check the oil level. See the How To Check/Add Oil section.

2. Push the stop switch (A), if equipped, to the on position (Figure 4).

3. Turn the fuel shut-off valve (B), if equipped, to the on position.

4. Move the throttle control (C)tothefast

position. Operate the engine in the fast

position.

5. Push the red primer (F) t hree times.

Note: Priming is usually unnecessary when restarting a warm engine.

Note: If you push the primer too many times, excessive fuel will flood the carburetor

and the engine will be difficult to s tart.

6. Make sure equipment drive controls, if equipped, are disengaged.

7. If the product is equipped with an engine stop lever (D), hold the engine stop lever

against the handle (Figure 5).

8. Rewind Start: Firmly hold the starter cord handle (E). Pull the starter cord handle

slowly until resistance is felt, then pull rapidly (Figure 4).

Note: If the engine does not start after repeated attempts, repeat Steps 6, 7, and 8. If

it still does not start, go to BRIGGSandSTRATTON.COM or call 1-800-233-3723 (in

USA).

WARNING: Rapid retraction of the starter cord (kickback) will pull your

hand and arm toward the engine faster than you can let go. Broken bones, fractures,

bruises or sprains could result. When starting engine, pull the starter cord slowly until

resistance is f elt and then pull rapidly to avoid kickback.

9. Electric Start: Turn the electric start switch to the on /start position.

Note: If the engine does not start after repeated attempts, repeat Steps 6, 7, and 9. If

it still does not start, go to BRIGGSandSTRATTON.COM or call 1-800-233-3723 (in

USA).

NOTICE: To extend the life of the starter, use short starting cycles (five seconds

maximum). Wait one minute between starting cycles.

Choke System - Figure

4 5

1. Check the oil level. See the How To Check/Add Oil section.

2. Push the stop switch (A), if equipped, to the on position (Figure 4).

3. Turn the fuel shut-off valve (B), if equipped, to the on position.

4. Move the throttle control (C)tothefast

position. Operate the engine in the fast

position.

5. Move the choke lever (G), or the combination choke/throttle lever, to the

choke

position.

Note: Choke is usually unnecessary when restarting a warm engine.

6. Make sure equipment drive controls, if equipped, are disengaged.

7. If the product is equipped with an engine stop lever (D), hold the engine stop lever

against the handle (Figure 5).

8. Rewind Start: Firmly hold the starter cord handle (E). Pull the starter cord handle

slowly until resistance is felt, then pull rapidly (Figure 4).

Note: If the engine does not start after repeated attempts, go to

BRIGGSandSTRATTON.COM or call 1-800-233-3723 (in USA).

WARNING: Rapid retraction of the starter cord (kickback) will pull your

hand and arm toward the engine faster than you can let go. Broken bones, fractures,

bruises or sprains could result. When starting engine, pull the starter cord slowly until

resistance is f elt and then pull rapidly to avoid kickback.

9. Electric Start: Turn the electric start switch to the on /start position.

Note: If the engine does not start after repeated attempts, go to

BRIGGSandSTRATTON.COM or call 1-800-233-3723 (in USA).

NOTICE: To extend the life of the starter, use short starting cycles (five seconds

maximum). Wait one minute between starting cycles.

10. As the engine warms up, move the choke control (G)totherun

position (Figure

4).

How To Stop The Engine - Figure

4 5

WARNING

Fuel and its vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

• Do not choke the carburetor to stop engine.

1. Release the engine stop lever lever (A, Figure 5)

Engine with Throttle Control: Move the throttle c ontrol (C, Figure 4) to the stop

position

Engine with Stop Switch: Push the stop switch (A, Figure 4) to the off position

Engine with Electric Start: Turn the electric start switch to the off/stop position.

See the equipment manual for the location and operation of the switch.

2. Engine with optional Fuel Shut-off: After the engine stops, turn the fuel shut-off

valve (B, Figure 4) to t he closed position.

Maintenance

NOTICE: If the engine is tipped during maintenance, the fuel tank must be empty and

thesparkplugsidemust be up. If the fuel tank is not empty and if the engine is tipped in

any other direction, it may be difficult to start due to oil or gasoline contaminating the air

filter and/or the spark plug.

Use only original equipment replacement parts. Other parts may not perform as

well, may damage the unit, and may result in injury. In addition, use of other parts

may void your warranty.

We recommend that you see any Briggs & Stratton Authorized Dealer for all

maintenance and service of the engine and engine parts.

NOTICE: All the components used to build this engine must remain in place for proper

operation.

Emissions Control

Maintenance, replacement, or repair of the emissions control devices and systems

may be performed by any non-road engine repair establishment or individual.

However, to obtain “no charge” emissions control service, the work must be performed

by a factory authorized dealer. See the Emissions Warranty.

Not for Reproduction

BRIGGSandSTRATTON.COM

Unintentional sparking can result in fire or electric shock.

Unintentional start-up can result in entanglement, traumatic

amputation, or laceration.

Fire hazard

WARNING

Before performing adjustments or repairs:

• Disconnect the spark plug wire and keep it away from the spark plug.

• Disconnect battery at negative terminal (only engines with electric start.)

• Use only correct tools.

• Do not tamper with governor spring, links or other parts to increase engine

speed.

• Replacement parts must be the same and installed in the same position as the

original parts.

• Do not strike the flywheel with a hammer or hard object because the flywheel

may later shatter during operation.

When testing for spark:

• Use approved spark plug tester.

• Do not check for spark with spark plug removed.

Maintenance Chart

First 5 Hours

• Change oil

Every8HoursorDaily

• Check engine oil level

• Clean area around muffler and controls

• Clean finger guard (if equipped)

Every 25 Hours or Annually

• Clean air filter *

• Clean pre-cleaner *

Every 50 Hours or Annually

• Change engine oil

• Replace oil filter (if equipped)

• Check muffler and spark arrester

Annually

• Replace air filter

• Replace pre-cleaner

• Replace spark plug

• Clean air cooling system *

• Clean/Replace fuel filter

• Check valve clearance **

* In dusty conditions or when airborne debris is present, clean more often.

** Not required unless engine performance problems are noted.

Carburetor Adjustment

Never make adjustments to the carburetor. The carburetor was set at the factory to

operate efficiently under most conditions. However, if adjustments are required, see a

Briggs & Stratton Authorized Dealer for service.

NOTICE: The manufacturer of the equipment on which this engine is installed specifies

the top speed at which the engine will be operated. Do not exceed this speed.

How To Replace The Spark Plug - Figure

Check the gap (A, Figure 6) with a wire gauge (B). If necessary, reset the gap. Install

and tighten the spark plug to the recommended torque. For gap setting or torque, see the

Specifications section.

Note: In some areas, local law requires using a resistor spark plug to suppress ignition

signals. If this engine was originally equipped with a resistor spark plug, use the same

type for replacement.

Inspect Muffler And Spark Arrester - Figure

Running engines produce heat. Engine parts, especially muffler,

become extremely hot.

Severe thermal burns can occur on contact.

Combustible debris, such as leaves, grass, brush, etc. can catch fire.

WARNING

• Allow muffler, engine cylinder and fins to cool before touching.

• Remove accumulated debris from muffler area and cylinder area.

• It is a violation of California Public Resource Code, Section 4442, to use or

operate the engine on any forest-covered, brush-covered, or grass-covered land

unless the exhaust system is equipped with a spark arrester, as defined in

Section 4442, maintained in effective working order. Other states or federal

jurisdictions may have similar laws. Contact the original equipment

manufacturer, retailer, or dealer to obtain a spark arrester designed for t he

exhaust system installed on this engine.

Inspect the muffler ( A, Figure 7) for cracks, corrosion, or other damage. Remove the

spark arrester ( B), if equipped, and inspect for damage or carbon blockage. If

replacement parts are required, make sure to use only original equipment replacement

parts.

WARNING: Replacement parts must be the same and installed in the

same position as the original parts or fire could result.

How To Change The Oil - Figure

2 8 9 10 11

WARNING

Fuel and its vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

• If you drain the oil from the top oil fill tube, the fuel tank must be empty or fuel

can leak out and result in a fire or explosion.

Used oil is a hazardous waste product and must be disposed of properly. Do not discard

with household waste. Check with your local authorities, service center, or dealer for safe

disposal/ recycling facilities.

Remove Oil

You c an drain t he oil from the bottom drain hole, the side drain hole, or from the top oil fill

tube.

1. With engine off but still warm, disconnect the spark plug wire (A) and keep it away

from the spark plug (Figure 8).

2. The engine is equipped with a bottom drain (B, Figure 9) and/or a side drain (C).

Removetheoildrainplug(D). Drain the oil into an approved container.

Note: Any of the oil drain plugs (D) shown may be installed in the engine.

3. After the oil has drained, install and tighten the oil drain plug.

4. If you drain the oil from the top oil fill tube (E), keep the spark plug end of the engine

(F) up (Figure 10). Drain the oil into an approved container.

WARNING: If you drain the oil from the top oil fill tube, the fuel tank must

be empty or fuel can leak out and result in a fire or explosion. To empty the fuel tank,

run the engine until it stops from lack of fuel.

Change The Oil Filter (if equipped)

Some models are equipped with an optional oil filter. For replacement intervals, see the

Maintenance chart.

1. Drain the oil from the engine. See “How To Change The Oil”.

2. Remove the oil filter (K) and dispose of properly. See Figure 11.

3. Before you install the new oil filter, lightly lubricate the oil filter gasket with fresh,

clean oil.

4. Install the oil filter by hand until the gasket contacts the oil filter adapter, then tighten

theoilfilter1/2to3/4turns.

5. Add oil. See Add Oil section.

6. Start and run the engine. As the engine warms up, check for oil leaks.

7. Stop the engine and check the oil level. It should be at the FULL mark on the

dipstick.

Add Oil

• Place engine level.

• Clean the oil fill area of any debris.

• See the Specifications section for oil capacity.

Not for Reproduction

1. Remove the dipstick (G) and wipe with a clean cloth (Figure 2).

2. Pour the oil slowly into the engine oil f ill (H). Do not overfill. After adding oil, wait

one minute and then check the oil level.

3. Install and tighten the dipstick.

4. Remove the dipstick and check the oil level. It should be at the top of t he full indicator

(J) on the dipstick.

5. Install and tighten the dipstick.

How To Service The Air Filter - Figure

WARNING

Fuel and its vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

• Never start or run the engine with the air cleaner assembly (if equipped) or the

air filter (if equipped) removed.

NOTICE: Do not use pressurized air or solvents to clean the filter. Pressurized air can

damage the f ilter and solvents will dissolve the filter.

1. Remove the fasteners (A) and the air filter cover (B). (Figure 12).

2. Remove the pre-cleaner (C) and the filter (D).

3. To loosen debris, gently tap the filter on a hard surface. If the filter is excessively

dirty, replace with a new filter.

4. Wash the pre-cleaner in liquid detergent and water. Then allow it to t horoughly air

dry. Do not oil t he pre-cleaner.

5. Assemble the dry pre-cleaner to the filter.

6. Install the filter and pre-cleaner into the base (E). Make sure filter fits securely in the

base.

7. Install air filter cover and secure with fasteners. Make sure the fasteners are tight.

How To Replace The Fuel Filter - Figure

WARNING

Fuel and its vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

• Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition

sources.

• Check fuel lines, tank, cap, and fittings frequently for cracks or leaks.

Replace if necessary.

• Before cleaning or replacing the fuel filter, drain the fuel tank or close the fuel

shut-off valve.

• Replacement parts must be the same and installed in the same position as the

original parts.

• If fuel spills, wait until it evaporates before starting engine.

1. Before replacing the fuel filter (A, Figure 13), if equipped, drain the fuel tank or close

the fuel shut-off valve. Otherwise, fuel can leak out and cause a fire or explosion.

2. Use pliers to squeeze tabs (B) on the clamps (C), then slide the clamps away from

the fuel filter. Twist and pull t he fuel lines (D) off of the fuel filter.

3. Check t he fuel lines for cracks or leaks. Replace if necessary.

4. Replace the fuel filter with an original equipment replacement filter.

5. Secure the fuel lines with the clamps as shown.

How To Clean The Air Cooling System - Figure

Running engines produce heat. Engine parts, especially muffler,

become extremely hot.

Severe thermal burns can occur on contact.

Combustible debris, such as leaves, grass, brush, etc. can catch fire.

WARNING

• Allow muffler, engine cylinder and fins to cool before touching.

• Remove accumulated debris from muffler area and cylinder area.

NOTICE: Do not use water to clean the engine. Water could contaminate the fuel

system. Use a brush or dry cloth to clean the engine.

This is an air cooled engine. Dirt or debris can restrict air flow and cause the engine to

overheat, resulting in poor performance and reduced engine life.

Use a brush or dry cloth to remove debris from the finger guard (A). Keep linkage,

springs and controls (B) clean. Keep area around and behind the muffler (C) free of any

combustible debris (Figure 14).

Storage

WARNING

Fuel and its vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

When Storing Fuel Or Equipment With Fuel In Tank

• Store away f rom furnaces, stoves, water heaters or other appliances that have

pilot lights or other ignition sour ces because they can ignite fuel vapors.

Fuel System

Fuel can become stale when stored over 30 days. Stale fuel causes acid and gum

deposits to form in the fuel system or on essential carburetor parts. To keep fuel fresh,

use Briggs & Stratton FRESH START

fuel stabilizer, available as a liquid additive or a

drip concentrate cartridge.

There is no need to drain gasoline from the engine if a f uel stabilizer is added according

to instructions. Run the engine for 2 minutes to circulate the stabilizer throughout the fuel

system. The engine and fuel can t hen be stored up to 24 months.

If gasoline in the engine has not been treated with a fuel stabilizer, it must be drained into

an approved container. Run the engine until it stops from lack of fuel. The use of a fuel

stabilizer in the storage container is recommended to maintain freshness.

Engine Oil

While the engine is still warm, change the engine oil.

NOTICE: Store the engine level (normal operating position). If the engine is tipped for

storage, the fuel tank must be empty and the spark plug side must be up. If the fuel

tank is not empty and if the engine is tipped in any other direction, it may be difficult to

start due to oil or gasoline contaminating the air filter and/or the spark plug.

Troubleshooting

Need Assistance? Go to BRIGGSandSTRATTON.COM or call 1-800-233-3723.

Specifications

Engine Specifications

Model 120000

Displacement 11.58 ci (190 cc)

Bore 2.688 in (68.28 mm)

Stroke 2.040 in (51.82 mm)

Oil Capacity 18 -- 20 oz (0.54 -- 0.59 L)

Tune-up Specifications *

Model 120000

Spark Plug Gap 0.020 in (0.51 mm)

Spark Plug Torque 180 lb-in (20 Nm)

Armature Air Gap 0.010 - 0.014 in (0.25 - 0.36 mm)

Intake Valve Clearance 0.004 - 0.008 in (0.10 - 0.20 mm)

Exhaust Valve Clearance 0.004 - 0.008 in (0.10 - 0.20 mm)

* Engine power will decrease 3.5% for each 1,000 feet (300 meters) above sea level and

1% for each 10° F(5.6° C) above 77° F(25° C). The engine will operate satisfactorily at

an angle up to 15°. Refer to the equipment operator’s manual for safe allowable

operating limits on slopes.

Common Service Parts n

Service Part Part Number

Air Filter, Oval 697029, 5059

Air Filter Pre -cleaner, Oval 273356

Oil -- SAE 30 100005

Oil Filter 692513

Fuel Additive 5041, 5058

Resistor Spark Plug 692051

Spark Plug Wrench 89838, 5023

Spark Tester 19368

Fuel Filter 298090, 5018

n We recommend that you see any Briggs & Stratton Authorized Dealer for all

maintenance and service of the engine and engine parts. Use only genuine Briggs &

Stratton parts.

Not for Reproduction

10 BRIGGSandSTRATTON.COM

BRIGGS & STRATTON ENGINE OWNER WARRANTY POLICY

September 2008

Briggs & Stratton Corporation will repair or replace, free of charge, any part(s) of the engine that is defective in material or workmanship or both. Transportation charges on

product submitted for repair or replacement under this warranty must be borne by purchaser. This warranty is effective for and is subject to the time periods and conditions

stated below. For warranty service, find the nearest Authorized Service Dealer in our dealer locator map at BRIGGSandSTRATTON.COM, or by calling

1-800-233-3723, or as listed in the ‘Yellow Pages’.

There is no other expressed warranty. Implied warranties, including those of merchantability and fitness for a particular purpose, are limited to one year from

purchase, or to the extent permitted by law and all implied warranties are excluded. Liability for incidental or consequential damages are excluded to the extent

exclusion is permitted by law. Some states or countries do not allow limitations on how long an implied warranty lasts, and some states or countries do not allow the

exclusion or limitation of incidental or consequential damages, so the above limitation and exclusion may not apply to you. This warranty gives you specific legal rights and

you may also have other rights which vary from state to state and country to country.

LIMITED WARRANTY

STANDARD WARRANTY TERMS *

Brand/Product Type Consumer Use Commercial Use

Vanguardt

2 years 2 years

Extended Life Seriest; I/C

; Intekt I/C

; Intekt Pro;

Professional Seriest with Dura-Boret Cast Iron Sleeve;

850 Seriest with Dura-Boret Cast Iron Sleeve;

Snow Series MAXt with Dura-Boret Cast Iron Sleeve

2 years 1 year

All Other Briggs & Stratton Engines 2 years 90 days

* These are our standard warranty terms, but occasionally there may be additi onal warranty coverage that was not determined at time of publication. For a listing of

current warranty terms for your engine, go to BRIGGSandSTRATTON.COM or contact your Authorized Briggs & Stratton Service Dealer.

Engines used on Home Standby Generator applications are warranted under consumer use only. This warranty does not apply to engines on equipment used for

prime power in place of a utility. Engines used in competitive racing or on commercial or rental tracks are not warranted.

The warranty period begins on the date of purchase by the first retail consumer or commercial end user, and continues for the period of time stated in the table above. “Consumer

use” means personal residential household use by a ret ail consumer. “Commercial use” means all other uses, including use for commercial, income producing or rental purposes.

Once an engine has experienced commercial use, it shall thereafter be considered as a commercial use engine for purposes of this warranty.

No warranty registration is necessary to obtain warranty on Briggs & Stratton Products. Save your proof of purchase receipt. If you do not provide proof of the initial

purchase date at the time warranty service is requested, the manufacturing date of the product will be used to determine the warranty period.

About Your Warranty

Briggs & Stratton welcomes warranty repair and apologizes to you for being

inconvenienced. Any Authorized Service Dealer may perform warranty repairs. Most

warranty repairs are handled routinely, but sometimes requests for warranty service may

not be appropriate.

If a customer differs with the decision of t he Service Dealer, an investigation will be made

to determine whether the warranty applies. Ask the Service Dealer to submit all

supporting facts to his Distributor or the Factory for review. If the Distributor or the

Factory decides that the claim is justified, the customer will be fully reimbursed for those

items that are defective. To avoid misunderstanding which might occur between the

customer and the Dealer, listed below are some of the causes of engine failure that the

warranty does not cover.

Normal wear: Engines, like all mechanical devices, need periodic parts service and

replacement to perform well. Warranty will not cover repair when normal use has

exhausted the life of a part or an engine. Warranty would not apply if engine damage

occurred because of misuse, lack of routine maintenance, shipping, handling,

warehousing or improper installation. Similarly, warranty is v oid if the serial number of the

engine has been removed or the engine has been altered or modified.

Improper maintenance: The life of an engine depends upon the conditions under which

it operates, and the care it receives. Some applications, such as tillers, pumps and rotary

mowers, are very often used in dusty or dirty conditions, which can cause what appears

to be premature wear. Such wear, when caused by dirt, dust, spark plug cleaning grit, or

other abrasive material that has entered th e engine because of improper maintenance, is

not covered by warranty.

This warranty covers engine related defective material and/or workmanship only

and not replacement or refund of the equipment to which the engine may be

mounted. Nor does the warranty extend to repairs required because of:

1 Problems caused by parts that are not original Briggs & Stratton parts.

2 Equipment controls or installations that prevent starting, cause unsatisfactory engine

performance, or shorten engine life. (Contact equipment manufacturer.)

3 Leaking carburetors, clogged fuel pipes, sticking valves, or other damage, caused

by using contaminated or stale f uel.

4 Parts which are scored or broken because an engine was operated with insufficient

or contaminated lubricating oil, or an incorrect grade of lubricating oil (check and

refill when necessary, and change at recommended intervals). OIL GARD may not

shut down running engine. Engine damage may occur if oil level is not properly

maintained.

5 Repair or adjustment of associated parts or assemblies such as clutches,

transmissions, remote c ontrols, etc., which are not manufactured by Briggs &

Stratton.

6 Damage or wear to parts caused by dirt, which entered the engine because of

improper air cleaner maintenance, re-assembly, or use of a non-original air cleaner

element or cartridge. At recommended intervals, clean and/or replace the filter as

stated in the Operator’s Manual.

7 Parts damaged by over-speeding, or overheating caused by grass, debris, or dirt,

which plugs or clogs the c ooling fins, or flywheel area, or damage caused by

operating the engine in a confined area without sufficient ventilation. Clean engine

debris at recommended intervals as stated in the Operator’s Manual.

8 Engine or equipment parts broken by excessive vibration caused by a loose engine

mounting, loose cutter blades, unbalanced blades or loose or unbalanced impellers,

improper attachment of equipment to engine crankshaft, over-speeding or other

abuse in operation.

9 A bent or broken crankshaft, caused by striking a solid object with the cutter blade of

a rotary lawn mower, or excessive v-belt tightness.

10 Routine tune-up or adjustment of the engine.

11 Engine or engine component failure, i.e., combustion chamber, valves, valve seats,

valve guides, or burned starter motor windings, caused by the use of alternate fuels

such as, liquified petroleum, natural gas, altered gasolines, etc.

W arranty service is available only through authorized service dealers by Briggs &

Stratton Corporation. Locate your nearest Authorized Service Dealer in our dealer

locator map on BRIGGSandSTRATTON.COM or by calling 1-800-233-3723, or as

listed in the ‘Yello w Pages’.

Not for Reproduction

California, U.S. EPA, and Briggs & Stratton Corporation Emissions Control Warranty Statement

Your Warranty Rights And Obligations

February 2009

The California Air Resources Board, U.S. EPA, and Briggs & Stratton (B&S) are pleased

to explain t he emissions control system warranty on your Model Year 2009 and later

engine/equipment. In California, new small off-road engines and large spark ignited

engines less than or equal to 1.0 liter must be designed, built, and equipped to meet the

State’s stringent anti-smog standards. B&S must warrant the emissions control system

on your engine/equipment for the periods of time listed below provided there has been

no abuse, neglect, or improper maintenance of your engine or equipment.

Your emissions control system may include parts such as the carburetor or fuel injection

system, fuel tank, ignition system, and catalytic converter. Also included may be hoses,

belts, connectors, sensors, and other emissions-related assemblies.

Where a warrantable condition exists, B&S will repair your engine/equipment at no cost

to you including diagnosis, parts, and labor.

Manufacturer’s Warranty Coverage:

Small off-road engines and large spark ignited engines less than or equal to 1.0 liter are

warranted for two years. If any emissions-related part on your engine/equipment is

defective, the part will be repaired or replaced by B&S.

Owner’s Warranty Responsibilities:

• As the engine/equipment owner, you are responsible for the performance of the

required maintenance listed in your owner’s manual. B&S recommends that you

retain all receipts covering maintenance on your engine/equipment, but B&S cannot

deny warranty solely for the lack of receipts or your failure to ensure the performance

of all scheduled maintenance.

• As the engine/equipment owner, you should however be aware that B&S may deny

you warranty coverage if your engine/equipment or a part has failed due to abuse,

neglect, improper maintenance, or unapproved modifications.

• You are responsible for presenting your engine/equipment to a B&S distribution

center, servicing dealer, or other equivalent entity, as applicable, as soon as a

problem exists. The warranty repairs should be completed in a reasonable amount of

time, not to exceed 30 days. If you have any questions regarding your warranty

rights and responsibilities, you should contact B&S at (414) 259-5262.

Briggs & Stratton Emissions Control Warranty Provisions

The following are specific provisions relative to your Emissions Control Warranty Coverage. It is in addition to the B&S engine warranty for non-regulated engines found in the

Operator’s Manual.

1. Warranted Emissions Parts

Coverage under this warranty extends only to the parts listed below (the emissions

control systems parts) to the extent these parts were present on the engine

purchased.

a. Fuel Metering System

• Cold start enrichment system (soft choke)

• Carburetor and internal parts

• Fuel pump

• Fuel line, fuel line fittings, clamps

• Fuel tank, cap and tether

• Carbon canister

b. Air Induction System

• Air cleaner

• Intake manifold

• Purge and vent line

c. Ignition System

• Spark plug(s)

• Magneto ignition system

d. Catalyst System

• Catalytic converter

• Exhaust manifold

• Air injection system or pulse valve

e. Miscellaneous Items Used in Above Systems

• Vacuum, temperature, position, time sensitive valves and switches

• Connectors and assemblies

2. Length of Coverage

For a period of two years from date of original purchase, B&S warrants to the original

purchaser and each subsequent purchaser that the engine is designed, built, and

equipped so as to conform with all applicable regulations adopted by the Air

Resources Board; that it is free from defects in material and workmanship that could

cause the failure of a warranted part; and that it is identical in all material respects to

the engine described in the manufacturer’s application for certification. The warranty

period begins on the date the engine is originally purchased.

The warranty on emissions-related parts is as follows:

• Any warranted part that is not scheduled for replacement as required

maintenance in the owner’s manual supplied, is warranted for the warranty

period stated above. If any such part fails during the period of warranty

coverage, the part will be repaired or replaced by B&S at no charge to the

owner. Any such part repaired or replaced under the warranty will be warranted

for the remaining warranty period.

• Any warranted part that is scheduled only for regular inspection in the owner’s

manual supplied, is warranted for the warranty period stated above. Any such

part repaired or replaced under warranty will be warranted for the remaining

warranty period.

• Any warranted part that is scheduled for replacement as required maintenance

in the owner’s manual supplied, is warranted for the period of time prior to the

first scheduled replacement point for that part. If the part fails prior to the first

scheduled replacement, the part will be repaired or replaced by B&S at no

charge to the owner. Any such part repaired or replaced under warranty will be

warranted for t he remainder of the period prior to the first scheduled

replacement point for the part.

• Add on or modified parts that are not exempted by the Air Resources Board

may not be used. The use of any non exempted add on or modified parts by the

owner will be grounds for disallowing a warranty claim. The manufacturer will

not be liable to warrant failures of warranted parts caused by the use of a non

exempted add on or modified part.

3. Consequential Coverage

Coverage shall extend to the failure of any engine components caused by the

failure of any warranted emissions parts.

4. Claims and Coverage Exclusions

Warranty claims shall be filed according to the provisions of the B&S engine

warranty policy. Warranty coverage does not apply to failures of emissions parts

that are not original equipment B&S parts or to parts that fail due to abuse, neglect,

or improper maintenance as set forth in the B&S engine warranty policy. B&S is not

liable for warranty coverage of failures of emissions parts caused by the use of

add-on or modified parts.

Look For Relevant Emissions Durability Period and Air Index Information

On Your Small Off-Road Engine Emissions Label

Engines that are certified to meet the California Air Resources Board (CARB) small

off-road Emissions Standard must display information regarding the Emissions Durability

Period and the Air Index. Briggs & Stratton makes this information available to the

consumer on our emissions labels. The engine emissions label will indicate certification

information.

The Emissions Durability Period describes the number of hours of actual running time

for which the engine is certified to be emissions compliant, assuming proper

maintenance in accordance with the Operating & Maintenance Instructions. The

following categories are used:

Moderate:

Engine is certified to be emissions compliant for 125 hours of actual engine running time.

Intermediate:

Engine is certified to be emissions compliant for 250 hours of actual engine running time.

Extended:

Engine is certified to be emissions compliant for 500 hours of actual engine running time.

For example, a typical walk-behind lawn mower is used 20 to 25 hours per year.

Therefore, the Emissions Durability Period of an engine with an intermediate rating

would equate t o 10 to 12 years.

Briggs & Stratton engines are certified to meet the United States Environmental

Protection Agency (USEPA) Phase 2 emissions standards. For Phase 2 certified

engines, the Emissions Compliance Period referred to on the Emissions Compliance

label indicates the number of operating hours for which the engine has been shown to

meet Federal emissions requirements.

For engines less than 225 cc displacement.

Category C = 125 hours , Category B = 250 hours , Category A = 500 hours

For engines of 225 cc or more displacement.

Category C = 250 hours , Category B = 500 hours , Category A = 1000 hours

Not for Reproduction

12 BRIGGSandSTRATTON.COM

Generelle oplysninger

I forbindelse med reservedele eller tekni sk assistance skal du nedenfor registrere

motormodel, type og kodenumre sammen med købsdatoen. Disse tal f indes på din motor

(se siden Udstyr og betjeningselementer).

Købsdato:

Motormodel:

DD/MM/ÅÅÅÅ

Modelserie: Kode:Ty pe:

Oplysninger om motors nominelle effekt

Den nominelle bruttoeffekt for individuelle benzinmotormodeller er mærket i

overensstemmelse med den amerikanske organisation SAEs (Society of Automotive

Engineers) lovsamling J1940 (Small Engine Power & Torque Rating Procedure), og

effektydelsen er opnået og rettet til i overensstemmelse med SAE J1995 (Revidering

2002-05). Tilspændingsmomenter fås ved et omdrejningstal på 3060 omdr./min.; antallet

af hestekræfter fås ved et omdrejningstal på 3600 omdr./min. Den effektive motors

bruttoeffekt vil være lavere og være påvirket af, bl.a. omgivende arbejdsforhold og

maskine-til-maskine foranderligheder. Under forudsætning af både den brede vifte af

produkter, som motorerne er monteret på og variationen af de miljømæssige hensyn, der

skal tages ved drift af udstyret, da vil benzinmotoren ikke udvikle den nominelle

bruttoeffekt, når denne anvendes i et nærmere angivet effektudstyr (den effektive

effektværdi “on-site” eller nettoeffekt). Denne forskel skyldes en række faktorer, der

inkluderer, men som ikke er begrænset til, tilbehør (luftfiltre, udstødning, ladning,

afkøling, karburator, brændstofpumpe, mv.), anvendelsesbegrænsninger, omgivende

arbejdsforhold (temperatur, fugt, højde) og maskine-til-maskine foranderlighed. Grundet

fabrikations- og kapacitetsbegrænsninger, kan Briggs & Stratton erstatte den

pågældende seriemotor med en motor af højere nominel ydelse.

erhed for operatoren

Brand Giftige dampeBevægelige dele Olie Langsom

StopHurtig Eksplosion Stød Brændstof

BrændstofhaneChoker On/Off-kontakt

Bær

beskyttelsesbriller

Varm overfladeLæs vejledningenFarligt kemikalie Forfrysninger

SIKKERHEDS- OG KONTROLSYMBOLER

Tilbageslag

Advarselssymbolet anvendes til at fremhæve sikkerhedsoplysninger om farer , der

kan medføre alvorlig personskade. Ordene FARE, ADVARSEL og FORSIGTIG anvendes

sammen med advarselssymbolet til at angive, hvor stor risikoen for skader er og omfanget

eller alvoren af sådanne personskader . Desuden anvendes et faresymbol til at angive den

relevante type fare.

FARE angiver en farlig situation, som vil medføre død eller alvorlig

personskade, hvis den ikke undgås.

ADVARSEL angiver en farlig situation, som kan medføre død eller alvorlig

personskade, hvis den ikke undgås.

FORSIGTIG angiver en farlig situation, som kan medføre mindre eller

moderat personskade, hvis den ikke undgås.

BEMÆRK angiver en situation, der kan resultere i beskadigelse af

produktet.

ADVARSEL

Visse komponenter i produktet og tilhørende udstyr indeholder kemikalier, der i følge

staten Californien forårsager cancer, medfødte misdannelser eller andre skader på

forplantningssystemet. Vask hænder efter håndtering.

ADVARSEL

I henhold til amerikansk lovgivning (Californien) gøres der opmærksom på, at

udstødningsgasserne fra denne maskine indeholder kræftfremkaldende stoffer.

Disse stoffer kan ligeledes medføre fosterskader og kan have en negativ effekt på

forplantningsevnen.

ADVARSEL

Briggs & Stratton godkender eller autoriserer ikke brug af disse motorer på 3-hjulede

terrængående køretøjer, motorcykler, gokarts til fornøjelse/ikke-professionel brug,

luftfartøjer eller køretøjer til brug i konkurrencer. Brug af disse motorer til

ovennævnte formål kan forårsage tingsskade, alvorlig personskade (bl.a. lammelse)

og i værste tilfælde død.

BEMÆRK: Denne motor blev afsendt fra Briggs & Stratton uden olie. Før du starter

motoren, sørg altid for at påfylde olie i henhold til de instruktioner angivet i denne

manual. Hvis du starter motoren uden påfyldning af olie, vil denne blive beskadiget og vil

ikke kunne repareres mere og derfor ikke være dækket af garantien.

ADVARSEL

Benzin og benzindampe er yderst brandfarlige og eksplosive.

Brand eller eksplosion kan medføre alvorlige forbrændinger eller

døden.

Påfyldning af brændstof

• Sluk for motoren, og lad motoren køle af i mindst 2 minutter, før tankdækslet

fjernes.

• Påfyld k un benzin udendørs eller på et sted med god udluftning.

• Undgå at fylde for meget brændstof på tanken. Undlad at fylde helt op til

kanten på påfyldningsstudsen, således at der er plads til, at benzinen kan

udvide sig.

• Benzin skal opbevares i sikker afstand fra gnister, åben ild, vågeblus, varme

og andre mulige antændelseskilder.

• Foretag hyppige eftersyn af brændstofslanger, t anken og tankdækslet samt

fittings for revner og utætheder. Udskift om nødvendigt.

• Hvis du spilder benzin, så vent med at starte motoren, indtil benzinen er

fordampet.

Startafmotoren

• Sørg for, at tændrøret, lyddæmperen, tankdækslet og luftfilteret (hvis monteret)

er på plads og forsvarligt f astgjort.

• Tørn ikke motoren, når tændrøret er afmonteret.

• Hvis motoren er druknet, sættes chokeren (hvis monteret) i

”OPEN/RUN”-position (kør) og gasspjældsregulatoren i fast-position (hurtig),

hvorefter motoren tørnes, indtil den starter.

Betjening af redskabet

• Undgå at vippe motoren eller udstyret, således at benzinen løber ud.

• Tip ikke karburatoren til at standse motoren.

• Start aldrig motoren eller lad aldrig motoren køre med luftfilterenheden (hvis

monteret) eller luftfiltret (hvis monteret) fjernet.

Ved olieskift

• Hvis du tømmer olien fra oliepåfyldningsrøret i toppen, skal brændstoftanken

være tom, da brændstoffet ellers kan løbe ud og resultere i brand eller

eksplosion.

Transport af redskabet

• Transport skal foregå med TOM brændstoftank eller med brændstofhanen

LUKKET.

Opbevaring af brændstof og redskaber med brændstof i tanken

• Sørg for, at benzin og redskaber med brændstof i tanken opbevares i sikker

afstand fra fyr, ovne, vandvarmere og andre apparater, hvori der anvendes

vågeblus, samt andre antændelseskilder, da disse kan antænde

brændstofdampe.

Når motoren startes, dannes der gnister.

Gnister kan antænde brændbare gasarter, der befinder sig i

nærheden af motoren.

Dette kan medføre eksplosion og brand.

ADVARSEL

• Motoren må ikke startes, hvis der er naturgas eller flaskegas i nærheden.

• Der må ikke anvendes startvæske på dåse til at starte motoren, da dampene er

brændbare.

Not for Reproduction

Motorer udsender kulilte, der er en lugtfri og farveløs, giftig gasart.

Indånding af kulilte kan medføre kvalme, besvimelse eller døden.

ADVARSEL

• Motoren må kun startes og anvendes udendørs.

• Motoren må aldrig startes og anvendes i lukkede rum. Dette gælder også, selv

om døre og vinduer er åbne.

Hurtig tilbagetrækning af startsnoren (tilbageslag) vil trække hånd og

arm tilbage mod motoren, hurtigere end du kan nå at slippe snor en.

Dette kan medføre, at du brækker armen, får knoglebrud, blå mærker

eller forstrækninger.

ADVARSEL

• Når motoren startes, træk langsomt i startsnoren, indtil du mærker modstand, og

træk derefter hurtigt for at undgå tilbageslag.

• Fjern alt eksternt udstyr/ motorbelastninger før start af motoren.

• Direkte tilkoblede dele på udstyret f.eks. skæreknive, skovlhjul, remskiver,

kædehjul osv. skal være forsvarligt monteret.

Hænder, fødder, hår og tøj kan sætte sig fast i roterende dele.

Dette kan medføre, at legemsdele skæres af, eller at brugeren får

alvorlige snitsår.

ADVARSEL

• Udstyret må kun anvendes med alle sikkerhedsafskærmninger på plads.

• Hold hænder og fødder i sikker afstand fra roterende dele.

• Langt hår bør bindes op, og smykker og lignende genstande bør tages af.

• Undgå at bære løstsiddende tøj, tøj med snore eller andre genstande, der kan

sætte sig fast.

Kørende motorer udvikler varme. Motorens dele, især lyddæmperen,

bliver meget varme.

Kontakt med varme dele kan forårsage alvorlige forbrændinger.

Der kan gå ild i brændbart affald som f.eks. blade, græs og grene.

ADVARSEL

• Lyddæmper, cylinder og køleribber skal køle af, før du rører ved dem.

• Fjern snavs, der samler sig i området omkring lyddæmperen og cylinderen.

• Det er en overtrædelse af ”California Public Resource Code, Section 4442” at

bruge eller betjene motoren på skovdækkede, kratdækkede eller græsdækkede

områder med mindre, at udstødningssystemet er udstyret med en gnistfanger

som defineret i ”Section 4442”, der skal være i funktionel stand. Andre stater

eller føderale jurisdiktioner kan have lignende love. Kontakt den originale

udstyrsfabrikant, grossist eller forhandler for at købe en gnistfanger, der passer

til udstødningssystemet på motoren.

Gnister, som frembringes ved et uheld, kan medføre brand eller stød.

Hvis motoren startes ved et uheld, kan dette medføre, at personer

kommer i klemme i redskabets mekanismer, at legemsdele bliver

skåret af, eller at personer får snitsår.

Brandfare

ADVARSEL

Før justering eller reparation af motoren:

• Tag tændrørskablet af tændrøret, og hold det i sikker afstand fra tændrøret.

• Tag minuskablet af batteriet, hvis motoren er udstyret med el-starter.

• Brug kun korrekt værktøj.

• Foretag aldrig ændring af regulatorfjeder, regulatorforbindelser eller andre dele

for at øge motorens omdrejningstal.

• Udskiftningsdele skal være af samme type som originaldelene og skal monteres

samme sted.

• Slå aldrig på svinghjulet med en hammer eller en hård genstand, da dette kan få

svinghjulet til at splintres under drift.

Kontrol af gnist:

• Brug en godkendt gnisttester.

• Kontrollér ikke gnisten med tændrøret afmonteret.

Not for Reproduction

14 BRIGGSandSTRATTON.COM

Udstyr og betjeningselementer

Sammenhold illustrationen

med din motor for at lære placeringen af udstyr og

betjeningselementer.

A. Identifikation af motoren

Model,- type,- og kodenummer

B. Tændrør

C. Spædebold (ekstraudstyr)

D. Brændstoftank og tankdæksel

E. Luftfilter

F. Startsnorgreb

G. Oliepind

H. Olieaftapningsprop

I. Lyddæmper

Lyddæmperskærm (ekstraudstyr)

Gnistfanger (ekstraudstyr)

J. Choker (ekstraudstyr)

K. Gasspjældsregulator (ekstraudstyr)

L. Stopkontakt (ekstraudstyr)

M. Brændstofhane (ekstraudstyr)

N. Brændstoffilter (ekstraudstyr)

O. Fingerskærm

P. Oliefilter (ekstraudstyr)

Betjening

Oliekapacitet (se Specifikationer afsnittet)

Anbefalinger vedrørende olie

Vi anbefaler at bruge Briggs & Stratton Garanti-godkendte olier for den bedste ydelse.

Andre olier af høj kvalitet kan accepteres, såfremt disse hører under serviceklassificering

SF, SG, SH, SJ eller er af bedre kvaliteter. Anvend ikke specielle additiver.

Udendørs temperaturer bestemmer motorens rette olieviskositet. Brug skemaet til at

udvælge den bedste viskositet for de forventede udendørs temperaturintervaller.

SAE 30

10W-30

Syntetisk 5W-30

5W-30

°F °C

* Hvis en SAE 30 olie benyttes ved temperaturer under 40°F(4°C), vil det resultere i

startproblemer.

* Ved temperaturer over 80 °F(27°C) vil brugen af 10W-30 medføre et olieforbrug, der

er højere end normalt. Kontrollér oliestanden hyppigere.

Kontrol/påfyldning af olie - Figur

Før påfyldning eller kontrol af olien

• Sørg for, at motoren er vandret.

• Rengør oliepåfyldningsområdet for eventuelt snavs.

1. Tag oliepinden (G) ud, og tør den af med en ren klud (figur 2).

2. Sæt oliepinden tilbage, og spænd den fast.

3. Tag oliepinden ud, og kontrollér oliestanden. Kontrollér, at oliestanden er øverst på

mærket for fuld tank (J) på oliepinden.

4. Hvis oliestanden er lav, fyld langsomt olie ind i motorens oliepåfylder (H). Overfyld

ikke. Efter oliepåfyldning skal du vente et minut og derefter kontrollere oliestanden

igen.

5. Udskift og fastspænd oliepinden.

Anbefalinger vedr. brændstof

Benzinen skal leve op til disse krav:

• Ren, frisk, blyfri benzin.

• Oktantal på mindst 87/87 AKI (91 RON). Hvis motoren skal anvendes i

højtbeliggende områder, henvises til nedenstående.

• Benzin med op til 10% ethanol (gasohol) eller op til 15% MTBE

(methyl-tertiær-butylæter) k an anvendes.

BEMÆRK: Der må ikke anvendes ikke-godkendt benzin, såsom E85. Der må ikke

blandes olie i benzinen, og motoren må ikke modificeres, så den kan køre med

alternative brændstoffer. I så f ald vil motorens komponenter blive beskadiget, og

garantien på motoren bortfalder.

For at beskytte brændstofsystemet fra gummidannelse bland en brændstofstabilisator i

brændstoffet. Se afsnittet Opbevaring. Intet brændstof er ens. Hvis der opstår

problemer ved s tart eller ydelse, skift da brændstofleverandør eller skift

brændstofmærke. Denne motor er anerkendt til benzinbrug.

Emissionsreguleringssystemet for denne motor er EM (Engine Modifications) såkaldte

justeringer.

Anvendelse i højtbeliggende områder

I højtbeliggende områder på over 5.000 fod (1524 meter), er benzin med et oktantal på

mindst 85 /85 AKI (89 RON) acceptabelt. For at være følgagtig over for emissionerne, er

det nødvendigt at foretage justeringer i højtbeliggende områder. Drift uden foretagelse af

denne justering v il forårsage formindsket ydelse, forøget brændstofforbrug og stigende

emissioner. Henvend dig til en autoriseret Briggs & Stratton forhandler for at få

oplysninger vedrørende justeringer i højtbeliggende områder.

Betjening af motoren i højtbeliggende områder på under 2.500 fod (762 meter) med

sættet beregnet til anvendelse i højtbeliggende områder er ikke anbefalet.

Påfyldning af brændstof - Figur

ADVARSEL

Benzin og benzindampe er yderst brandfarlige og eksplosive.

Brand eller eksplosion kan medføre alvorlige forbrændinger eller

døden.

Påfyldning af brændstof

• Sluk for motoren, og lad motoren køle af i mindst 2 minutter, før tankdækslet

fjernes.

• Påfyld k un benzin udendørs eller på et sted med god udluftning.

• Undlad at fylde for meget brændstof i brændstoftanken. Undlad at fylde helt

op til k anten på påfyldningsstudsen, således at der er plads til at brændstoffet

kan udvide s ig.

• Brændstof skal opbevares i sikker afstand fra gnister, åben ild, vågeblus,

varme og andre mulige antændelseskilder.

• Foretag hyppige eftersyn af brændstofslanger, t anken og tankdækslet samt

fittings for revner og utætheder. Udskift om nødvendigt.

• Hvis du spilder benzin, så vent med at starte motoren, indtil benzinen er

fordampet.

1. Rengør brændstofdækselområdet for snavs og rester. Fjern brændstofdækslet (A,

figur 3).

2. Fyld brændstoftanken (B) op med brændstof. Undlad at fylde helt op til kanten på

påfyldningsstudsen (C), således at der er plads til at brændstoffet kan udvide sig.

3. Genmontér tankdækslet.

Startafmotoren

Hurtig tilbagetrækning af startsnoren (tilbageslag) vil trække hånd og

arm tilbage mod motoren, hurtigere end du kan nå at slippe snor en.

Dette kan medføre, at du brækker armen, får knoglebrud, blå mærker

eller forstrækninger.

ADVARSEL

• Når motoren startes, træk langsomt i startsnoren, indtil du mærker modstand, og

træk derefter hurtigt for at undgå tilbageslag.

ADVARSEL

Benzin og benzindampe er yderst brandfarlige og eksplosive.

Brand eller eksplosion kan medføre alvorlige forbrændinger eller

døden.

Startafmotoren

• Sørg for, at tændrøret, lyddæmperen, tankdækslet og luftfilteret (hvis monteret)

er på plads og forsvarligt f astgjort.

• Tørn ikke motoren, når tændrøret er afmonteret.

• Hvis motoren er druknet, sættes chokeren (hvis monteret) i

”OPEN/RUN”-position (kør) og gasspjældsregulatoren i fast-position (hurtig),

hvorefter motoren tørnes, indtil den starter.

Motorer udsender kulilte, der er en lugtfri og farveløs, giftig gasart.

Indånding af kulilte kan medføre kvalme, besvimelse eller døden.

ADVARSEL

• Motoren må kun startes og anvendes udendørs.

• Motoren må aldrig startes og anvendes i lukkede rum. Dette gælder også, selv

om døre og vinduer er åbne.

Not for Reproduction

BEMÆRK: Denne motor blev afsendt fra Briggs & Stratton uden olie. Før du starter

motoren, sørg altid for at påfylde olie i henhold til de instruktioner angivet i denne

manual. Hvis du starter motoren uden påfyldning af olie, vil denne blive beskadiget og vil

ikke kunne repareres mere og derfor ikke være dækket af garantien.

Identificer startsystemet

Før du starter motoren, skal du identificere typen af startsystem, som befinder sig på din

motor. Din motor vil have en af følgende typer.

• ReadyStart

system: Dette kendetegnes ved en temperaturkontrolleret automatisk

choker. Systemet har ikke en manuel choker eller en spædebold.

• Spædesystem: Dette kendetegnes ved en rød spædebold, som skal anvendes for

start ved kølige temperaturer. Systemet har ikke en manuel choker.

• Chokersystem: Dette kendetegnes ved en choker, som skal anvendes for start ved

kølige temperaturer. Nogle modeller har et separat chokergreb, mens andre modeller

har en kombination chokergreb/gasspjældsarm. Denne type har ikke en

spædeanordning.

For at starte din motor skal du følge anvisningerne gældende for din type startsystem.

Bemærk: Udstyr kan have fjernbetjeninger. Se udstyrsmanualen for information om

fjernbetjeningernes placering og betjening.

ReadyStart

system - Figur

4 5

1. Kontrollér oliestanden. Se i Kontrol/påfyldning af olie afsnittet.

2. Sørg for, at udstyrets kørselsbetjeningsanordninger, hvis monteret, er frakoblet.

3. Sæt stopknappen (A), hvis monteret, på on-position (figur 4).

4. Drej brændstofhanen (B), hvis monteret, på on-position.

5. Flyt gasspjældsregulatoren (C) i ”FAST”

position (hurtig). Kør motoren i

”FAST”

position (hurtig).

6. Hvis maskinen er udstyret med et motorstopgreb (D), hold da motorens stopgreb

mod håndtaget (figur 5).

7. Ved genstart: Hold fast i startsnorgrebet (E). Træk langsomt i startsnorgrebet, indtil

du mærker modstand, og træk derefter hurtigt i snoren (figur 4).

Bemærk: Hvis motoren ikke starter efter gentagne forsøg, skal du da gå til

BRIGGSandSTRATTON.COM eller ringe på 1-800-233-3723 (i USA).

ADVARSEL: Hurtig tilbagetrækning af startersnoren (tilbageslag) vil

trække hånd og arm tilbage mod motoren, hurtigere end du kan nå at slippe snoren.

Dette kan medføre, at du brækker armen, får knoglebrud, blå mærker eller

forstrækninger. Når motoren startes, træk langsomt i startsnoren indtil du mærker

modstand og træk derefter hurtigt for at undgå tilbageslag.

8. Elstart: Drej den elektriske startkontakt på on/ start position.

Bemærk: Hvis motoren ikke starter efter gentagne forsøg, skal du da gå til

BRIGGSandSTRATTON.COM eller ringe på 1-800-233-3723 (i USA).

BEMÆRK: For at forlænge starterens levetid, brug korte startperioder (maksimalt i

fem sekunder). Vent et minut mellem hver startperiode.

Spædesystem - Figur

4 5

1. Kontrollér oliestanden. Se i Kontrol/påfyldning af olie afsnittet.

2. Sæt stopknappen (A), hvis monteret, på on-position (figur 4).

3. Drej brændstofhanen (B), hvis monteret, på on-position.

4. Flyt gasspjældsregulatoren (C) i ”FAST”

position (hurtig). Kør motoren i

”FAST”

position (hurtig).

5. Skub den røde spædebold ind (F) tre gange.

Bemærk: Det er normalt udnødvendigt at spæde ved genstart af en varm motor.

Bemærk: Hvis du trykker for mange gange på spædebolden, vil overdrevent

brændstof drukne karburatoren, og motoren vil have svært ved at starte.

6. Sørg for, at udstyrets kørselsbetjeningsanordninger, hvis monteret, er frakoblet.

7. Hvis maskinen er udstyret med et motorstopgreb (D), hold da motorens stopgreb

mod håndtaget (figur 5).

8. Ved genstart: Hold fast i startsnorgrebet (E). Træk langsomt i startsnorgrebet, indtil

du mærker modstand, og træk derefter hurtigt i snoren (figur 4).

Bemærk: Hvis motoren ikke starter efter gentagne forsøg, gentag trin 6, 7 og 8. Hvis

den stadig ikke starter, gå til hjemmesiden BRIGGSandSTRATTON.COM eller ring

på 1-800-233-3723 (i USA).

ADVARSEL: Hurtig tilbagetrækning af startersnoren (tilbageslag) vil

trække hånd og arm tilbage mod motoren, hurtigere end du kan nå at slippe snoren.

Dette kan medføre, at du brækker armen, får knoglebrud, blå mærker eller

forstrækninger. Når motoren startes, træk langsomt i startsnoren indtil du mærker

modstand og træk derefter hurtigt for at undgå tilbageslag.

9. Elstart: Drej den elektriske startkontakt på on/ start position.

Bemærk: Hvis motoren ikke starter efter gentagne forsøg, gentag trin 6, 7 og 9. Hvis

den stadig ikke starter, gå til hjemmesiden BRIGGSandSTRATTON.COM eller ring

på 1-800-233-3723 (i USA).

BEMÆRK: For at forlænge starterens levetid, brug korte startperioder (maksimalt i

fem sekunder). Vent et minut mellem hver startperiode.

Chokersystem - Figur

4 5

1. Kontrollér oliestanden. Se i Kontrol/påfyldning af olie afsnittet.

2. Sæt stopknappen (A), hvis monteret, på on-position (figur 4).

3. Drej brændstofhanen (B), hvis monteret, på on-position.

4. Flyt gasspjældsregulatoren (C) i ”FAST”

position (hurtig). Kør motoren i

”FAST”

position (hurtig).

5. Flyt chokergrebet (G), eller kombinationen chokergreb/gasspjældsarm på

choker

position.

Bemærk: Brug af choker er normalt unødvendigt, når motoren er varm.