Yamaha NS-E50 Handleiding

Yamaha
Merk
Yamaha
Model
NS-E50
Categorie
Synthesizer
Type
Handleiding

Deze handleiding is ook geschikt voor

NS-E50
Natural Sound Effect Speaker System
PRECAUTIONS
This model is designed to be used as an effect
speaker
system.
Read these precautions carefully before using your
speaker.
● Any time you note distortion, reduce the volume control
on your amplifier to a lower setting. Never allow your
amplifier to be driven into “clipping”. Otherwise the
speaker may be damaged.
● When using an amplifier with a rated output power higher
than the nominal input power of the speaker, care should
be taken never to exceed the speaker’s maximum input.
● Do not attempt to clean the speaker with chemical
solvents as this might damage the finish. To clean, wipe
with a dry, soft cloth.
● To prevent the enclosure from warping or discoloring, do
not place the speaker where it will be exposed to direct
sunlight or excessive humidity.
● Do not place the speaker where it is liable to be knocked
over or struck by falling objects. Stable placement will
also ensure better sound performance.
● Placing the speaker on the same shelf or rack as the
turntable can result in feedback.
● As these speakers contain strong magnets, avoid placing
watches, magnetic tapes, etc. near them. Also, placing
the speakers near a TV set may impair picture color. If
this happens, move the TV set away from the speakers.
● Secure placement or installation is the owner’s
responsibility. YAMAHA shall not be liable for any
accident caused by improper placement or
installation of the speaker.
■ Mounting the speakers on a wall
The speakers can be mounted on a wall by using the holes
provided on the speakers’ back panels.
Fasten screws into a firm wall or wall support as shown in
the diagram, and hang the holes on the protruding screws.
WARNING:
* Each speaker weighs 1.7 kg (3 lbs. 12 oz.). Do not
mount them on thin plywood or soft wall surface material,
as the screws may come out of the flimsy surface,
causing the speakers to fall down and be damaged, or
result in personal injury.
* Do not fasten the speakers to wall with nails, adhesives,
or other unsound hardware. Long-term use and
vibrations may cause them to fall down.
* To avoid accidents resulting from tripping over loose
speaker cables, fix them to the wall.
40 mm
Holes
Diam. 4 – 5mm
2mm
Tapping screw
(Available at a
hardware store)
Wall or
wall support
Min.
12mm
SETTING UP THE SPEAKERS
Pads
Make sure that the screws are caught by a narrow part of
the holes securely.
Put the screws into a wall according to the figure shown
below.
SPECIFICATIONS
Type..........Full range acoustic-suspension speaker system
Speaker Unit...............................................10 cm full range
Input Terminal ......................................................Push-type
Nominal Impedance..................................................6 ohms
Frequency Response...................................70 Hz – 20 kHz
Nominal Input Power.....................................................25W
Music Input Power.........................................................80W
Sensitivity ............................................................90 dB/w/m
Dimensions (WxHxD)
...............................................170 mm x 280 mm x 107 mm
......................................................(6-11/16” x 11” x 4-3/16”)
Weight..................................................1.7 kg (3 lbs. 12 oz.)
Accessories............................2 speaker cables (10m each)
* Specifications subject to change without notice due to
product improvements.
* Care should be taken not to exceed the input power
values noted above.
BEFORE MAKING CONNECTIONS, MAKE SURE THAT
THE AMPLIFIER IS SWITCHED OFF.
■ CONNECTIONS
● Connect the push-type input terminals at the rear of the
speakers to the speaker output terminals of your
amplifier with the provided speaker cables.
● One side of the speaker cable is marked by a blue line.
Connect the (+) terminals on both the amplifier and the
speakers using this blue-marked side. Connect the (–)
terminals on both components using the unmarked side
of the cable.
● Connect one speaker to the left (marked L) terminals of
your amplifier, and another speaker to the right (marked
R) terminals, making sure not to reverse the polarity (+,
–). If one speaker is connected with reversed polarity, the
sound will be unnatural and lack bass.
Procedures:
➀ Press the tab on the terminal down, as shown in the
figure.
➁ Insert the bare speaker wire end properly into the
terminal hole. [Remove approx. 5 mm (1/4”) insulation
from the speaker cable.]
➂ Remove your finger from the tab to allow it to lock
snugly on the cable’s wire end.
➃ Test the security of the connection by tugging lightly on
the cable at the terminal.
Note
Do not let the bare speaker wires touch each other as
this could damage the speaker and/or the amplifier.
Blue line
Speaker (L)
Speaker (R)
Press tab
Blue line
Blue line
Speaker output
terminals of
the amplifier
CONNECTION TO YOUR AMPLIFIER
VU 89830
  • Page 1 1
  • Page 2 2

Yamaha NS-E50 Handleiding

Yamaha
Merk
Yamaha
Model
NS-E50
Categorie
Synthesizer
Type
Handleiding
Deze handleiding is ook geschikt voor
Download PDF
rapport

in andere talen

Gerelateerde artikelen