IMPORTANT!
Please record the serial number of this
unit in the space below.
Model:
Serial No.:
The serial number is located on the rear
of the unit.
Retain this Owner’s Manual in a safe
place for future reference.
WARNING
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE
THIS UNIT TO RAIN OR MOISTURE.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK), NO USER-SERVICEABLE
PARTS INSIDE, REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead
symbol, within an equilateral triangle,
is intended to alert you to the
presence of uninsulated “dangerous
voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an
equilateral triangle is intended to alert
you to the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying the
appliance.
•
Explanation of Graphical Symbols
CAUTION
OWNER’S MANUAL
CONTENTS
Safety Instructions....................2
Supplied Accessories...............3
Connections ............................4
Tuning Operations ...................7
Preset Tuning ..........................9
Receiving RDS Stations
(TX-580RDS only) .................13
Troubleshooting .....................18
Specifications ........................19
Natural Sound AM/FM Stereo Tuner
40 Station Random Access Preset Tuning
Automatic Preset Tuning
Multi-Status Station Memory
Rotary Encoder Tuning
Direct PLL Synthesizer Tuning
Preset Station Shifting Capability
Multi-Functions for RDS Broadcast Reception (TX-580RDS only)
TX-480
TX-480L
TX-580RDS
Thank you for selecting this YAMAHA Stereo Tuner.
2
1 Read Instructions – All the safety and operating
instructions should be read before the unit is operated.
2 Retain Instructions – The safety and operating instructions
should be retained for future reference.
3 Heed Warnings – All warnings on the unit and in the
operating instructions should be adhered to.
4 Follow Instructions – All operating and other instructions
should be followed.
5 Water and Moisture – The unit should not be used near
water – for example, near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming
pool, etc.
6 Carts and Stands – The unit should be used only with a
cart or stand that is recommended by the manufacturer.
6A A unit and cart combination should
be moved with care. Quick stops,
excessive force, and uneven
surfaces may cause the unit and
cart combination to overturn.
7 Wall or Ceiling Mounting – The unit
should be mounted to a wall or ceiling only as
recommended by the manufacturer.
8 Ventilation – The unit should be situated so that its location
or position does not interfere with its proper ventilation.
For example, the unit should not be situated on a bed,
sofa, rug, or similar surface, that may block the ventilation
openings; or placed in a built-in installation, such as a
bookcase or cabinet that may impede the flow of air
through the ventilation openings.
9 Heat – The unit should be situated away from heat sources
such as radiators, stoves, or other appliances that produce
heat.
10 Power Sources – The unit should be connected to a power
supply only of the type described in the operating
instructions or as marked on the unit.
11 Power-Cord Protection – Power-supply cords should be
routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying
particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the unit.
12 Cleaning – The unit should be cleaned only as
recommended by the manufacturer.
13 Nonuse Periods – The power cord of the unit should be
unplugged from the outlet when left unused for a long
period of time.
14 Object and Liquid Entry – Care should be taken so that
objects do not fall into and liquids are not spilled into the
inside of the unit.
15 Damage Requiring Service – The unit should be serviced
by qualified service personnel when:
A. The power-supply cord or the plug has been damaged;
or
B. Objects have fallen, or liquid has been spilled into the unit;
or
C. The unit has been exposed to rain; or
D. The unit does not appear to operate normally or exhibits a
marked change in performance; or
E. The unit has been dropped, or the cabinet damaged.
16 Servicing – The user should not attempt to service the unit
beyond those means described in the operating
instructions. All other servicing should be referred to
qualified service personnel.
17 Power Lines – An outdoor antenna should be located away
from power lines.
18 Grounding or Polarization – Precautions should be taken
so that the grounding or polarization is not defeated.
19 Outdoor Antenna Grounding – If an outside antenna is
connected to this unit, be sure the antenna system is
grounded so as to provide some protection against voltage
surges and built-up static charges. Article 810 of the
National Electrical Code, ANSI/NFPA 70, provides
information with regard to proper grounding of the mast
and supporting structure, grounding of the lead-in wire to
an antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to
grounding electrodes, and requirements for the grounding
electrode.
YAMAHA and the Electronic Industries Association’s Consumer
Electronics Group want you to get the most out of your
equipment by playing it at a safe level. One that lets the sound
come through loud and clear without annoying blaring or
distortion – and, most importantly, without affecting your
sensitive hearing. Since hearing damage from loud sounds is
often undetectable until it is too late, YAMAHA
and the Electronic Industries Association’s
Consumer Electronics Group recommend you
to avoid prolonged exposure from excessive
volume levels.
We Want You Listening For A Lifetime
SAFETY INSTRUCTIONS
Note to CATV system installer:
This reminder is provided to call the CATV system
installer's attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be
connected to the grounding system of the building, as close
to the point of cable entry as practical.
EXAMPLE OF ANTENNA GROUNDING
MAST
GROUND
CLAMP
ANTENNA
LEAD IN
WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810–20)
GROUNDING CONDUCTORS
(NEC SECTION 810–21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250. PART H)
ELECTRIC
SERVICE
EQUIPMENT
NEC – NATIONAL ELECTRICAL CODE
3
1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC, to
use the product.
2. IMPORTANT : When connecting this product to
accessories and/or another product use only high quality
shielded cables. Cable/s supplied with this product
MUST be used. Follow all installation instructions.
Failure to follow instructions could void your FCC
authorization to use this product in the USA.
3. NOTE : This product has been tested and found to
comply with the requirements listed in FCC Regulations,
Part 15 for Class “B” digital devices. Compliance with
these requirements provides a reasonable level of
assurance that your use of this product in a residential
environment will not result in harmful interference with
other electronic devices.
This equipment generates/uses radio frequencies and, if
not installed and used according to the instructions
found in the users manual, may cause interference
harmful to the operation of other electronic devices.
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this product
is found to be the source of interference, which can be
determined by turning the unit “OFF” and “ON”, please try
to eliminate the problem by using one of the following
measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA
90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
FCC INFORMATION (U.S.A.)
1. This unit is a sophisticated AM/FM stereo tuner. To assure
proper operation and the best possible performance,
please read this manual carefully.
2. Choose the installation location for the unit carefully.
Avoid placing it in direct sunlight or close to a source of
heat. Also avoid locations subject to vibration and
excessive dust, heat, cold or moisture. Keep it away from
such sources of hum as transformers or motors.
3. Do not open the cabinet, because this may result in
damage to the unit or electrical shock. If a foreign object
should get into the unit, contact your local dealer.
4. To prevent lightning damage, disconnect the AC power
plug and disconnect the antenna cable when there is an
electrical storm.
5. When disconnecting the power plug from the wall outlet,
always pull directly on the plug; never pull the cord itself.
6. Do not use force when operating switches and other
controls.
7. When moving the unit, be sure to first disconnect the
power plug and disconnect all wires connected from the
unit to other equipment.
8. Do not attempt to clean this unit with chemical solvents,
because this may damage the finish. Use a clean, dry
cloth.
9. Be sure to read the “TROUBLESHOOTING” section of this
manual for advice on common operating errors before
concluding that the unit is faulty.
10.Keep this manual in a safe place for future reference.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT
SUPPLIED ACCESSORIES
After unpacking, check that the following parts are contained.
AM Loop Antenna Indoor FM Antenna Audio connection cord
ANTENNA CONNECTIONS
●
Each antenna should be connected to the designated terminals correctly, referring to the following figure.
●
Both AM and FM indoor antennas are included with this unit. In general, these antennas will probably provide sufficient signal
strength. Nevertheless, a properly installed outdoor antenna will give clearer reception than an indoor one. If you experience
poor reception quality, an outdoor antenna may result in improvement.
4
CONNECTIONS
75Ω UNBAL.
FM ANT GND AM ANT
Outdoor FM antenna
Outdoor AM antenna
AM loop
antenna
(included)
Ground
75-ohm
antenna
adapter
Indoor FM
antenna
(included)
75-ohm/300-ohm
antenna adapter
75-ohm
coaxial cable
300-ohm
feeder
m Optional outdoor FM antenna
Consult with your dealer or authorized service center about the
best method of selecting and erecting an outdoor FM antenna.
The choice of the feeder cable is also important. Flat ribbon-
shaped twin-lead cable performs well electrically, and is
cheaper and somewhat easier to handle when routing it
through windows and around rooms. Coaxial cable is more
expensive, does a much better job of minimizing interference,
is less prone to the effects of weather and close-by metal
objects, and is nearly as good a signal conductor as feeder
cable, particularly for foam-type coaxial cables. Coaxial cable
is somewhat more difficult to install at the point where the
cable enters the building. If coaxial cable is selected, make
sure the antenna is designed to be used with that type of
cable.
* Use a 75-ohm/300-ohm antenna adapter (not included) or a
75-ohm antenna adapter (not included) for connections.
300-ohm feeder cable 75-ohm coaxial cable
75-ohm/300-ohm antenna adapter
Notes for FM antenna installation
●
To minimize automobile ignition noise, locate the antenna
as far from heavy traffic as possible.
●
Keep the feeder cable or coaxial cable as short as possible.
Do not bundle or roll up excess cable.
●
The antenna should be at least two meters (6.6 feet) from
reinforced concrete walls or metal structures.
5
Connecting the indoor FM antenna
*If you connect an outdoor FM antenna to this unit, do not connect the indoor FM antenna to this unit.
Connecting the AM loop antenna
Orient so that the best
reception is obtained.
* The AM loop antenna should be placed apart from the main unit. The antenna may be hung on a wall.
* The AM loop antenna should be kept connected, even if an outdoor AM antenna is connected to this unit.
1
3
2
300-ohm feeder
cable
75-ohm coaxial
cable
75-ohm antenna
adapter
75-ohm coaxial
cable
m Optional outdoor AM antenna
In steel buildings or at a great distance from the transmitter, it
may be necessary to install an outside long wire antenna.
GND terminal
For maximum safety and minimum interference, connect
the GND terminal to a good earth ground. A good earth
ground is a metal stake driven into moist earth.
6
CONNECTIONS TO THE AMPLIFIER
●
Before making any connections, switch OFF the power to
this unit and the amplifier or other component.
●
Be sure that the connections from the left (“L”) and right
(“R”) OUTPUT terminals are connected to the
corresponding (left and right) input terminals of the amplifier
or other component.
*This unit has a remote control sensor. It receives signals
from a remote control transmitter provided with a YAMAHA
amplifier.
OUTPUT
RL
TUNER
L
R
75Ω UNBAL.
FM ANT GND AM ANT
Amplifier
Connection cord (included)
This unit
To AC outlet
Remote control sensor
* Parts in shaded area are ( )
present on TX-580RDS only.
1
2 Select the reception band while watching the display.
3
4 Tune to a desired station.
To tune to a higher frequency, slightly turn the control
to the right. To tune to a lower frequency, slightly turn
the control to the left.
5 If the station where tuning search stopped is not the
desired one, turn again.
* If the tuning search does not stop at the desired
station, change to the MANUAL TUNING method as
described on the following page.
Normally, if station signals are strong and there is no interference, quick automatic-search tuning (AUTOMATIC TUNING) is
possible. However, if signals of the station you want to select are weak, you must tune to it manually (MANUAL TUNING).
AUTOMATIC TUNING
7
TUNING OPERATIONS
POWER
FM/AM
TUNING MODE
AUTO/MAN’L MONO
AUTO TUNING
TUNING
TUNING
FM/AM/LW
1
23
4, 5
FM AM
or
FM MW LW
,
or
TX-480, TX-580RDS
TX-480L
1 Follow steps 1 and 2 on the previous page.
2
3 Tune to a desired station manually.
Note
If you tune to an FM station manually, it is received in
monaural mode automatically to increase the signal quality.
MANUAL TUNING
8
TUNING MODE
AUTO/MAN’L MONO
2
3
“AUTO TUNING” goes off.
Display information
➀
Displays the band and frequency of the received station.
* TX-580RDS only
If an RDS station is received, the frequency is then
replaced by the station name. (However, if the PS data
cannot be received within 5 seconds, “NO PS” flashes,
and then it returns to the frequency display.)
Refer to page 14 for details.
➁
Illuminates when an FM stereo broadcast is received in
stereo.
➂
Indicates the signal level of the received station.
STEREO
0
MHz
40 60
20
l00
1
3
2
STEREO
0
MHz
20
l00
FM
12
3
TX-580RDS
TX-480, TX-480L
TUNING
* Parts in shaded area are ( )
present on TX-580RDS only.
1 Tune to a desired station.
(Refer to pages 7–8 for tuning procedure.)
2 Select a desired page (A – E) of preset station buttons
while watching the display.
3
4 Press a preset station button before “MEMORY”
goes off from the display.
* In the same way, program other stations to A2, A3 ... A8.
* You can program more stations to the preset station
buttons on other pages in the same way by selecting
other pages in step 2.
11 Select the page of preset station buttons.
22
Select the desired preset station button.
Notes
●
A new setting can be programmed in place of the former
one.
●
For presets, the setting of the reception mode (stereo or
monaural) is stored along with the station frequency.
Memory back-up
The memory back-up circuit prevents the programmed data
from being lost even if the POWER switch is set off or the
power plug is disconnected from the AC outlet or the power is
cut due to temporary power failure. If, however, the power is
cut for more than one week, the memory may be erased. If
so, it can be re-programmed by simply following the PRESET
TUNING steps.
9
MANUAL PRESET TUNING
This unit can store station frequencies (selected by tuning operation) by using the preset station buttons. With this function, you can
select any desired station by only pressing the corresponding preset station button. Up to 40 stations (8 stations x 5 pages) can be
stored.
PRESET TUNING
To store stations
To recall a preset station
3
2, 11 4, 22 (Preset station buttons)
A/B/C/D/E
MEMORY
MAN’L/AUTO FM
MEMORY
A/B/C/D/E
Flashes on and off
for about 5 seconds.
A/B/C/D/E 1 2345678
PRESET STATIONS
A/B/C/D/E 1 2345678
PRESET STATIONS
PRESET
STEREO
0
MHz
40 60
20
l00
AUTO TUNING
AUTO TUNING
PRESET
STEREO
0
MHz
20
l00
FM
Shows the displayed station has been
programmed to A1.
TX-580RDS
TX-480, TX-480L
* Parts in shaded area are ( )
present on TX-580RDS only.
10
AUTOMATIC PRESET TUNING
You can also make use of an automatic preset tuning function for FM stations only. By this function, this unit performs automatic
tuning and stores FM stations with strong signals sequentially. Up to 40 stations are stored automatically in the same way as in the
manual preset tuning method on page 9.
TX-580RDS only
* Only RDS stations can be stored by this function.
To store stations
1
2
Flashes.
3 Slightly turn the TUNING control to the right (or to the
left).
* When turned to the right, automatic tuning is
performed toward higher frequencies. When turned
to the left, automatic tuning is performed toward lower
frequencies.
This unit performs automatic tuning and received stations
are programmed to A1, A2 ... A8 sequentially.
* If more than 8 stations are received, they are also
programmed to other pages (B, C, D and E) of preset
station buttons in that order.
If you want to store the first station received by the
automatic preset tuning to a desired preset station
number.
If, for example, you want to store the received first station to
C5, select “C5” by using the A/B/C/D/E button and the preset
station buttons after step 2, and then follow step 3. The
received first station is stored to C5, and next stations to C6,
C7 ... sequentially.
If stations are stored up to E8, the automatic preset tuning is
finished automatically.
When the automatic preset tuning is finished
The display shows the frequency of the last preset station.
Check the contents and the number of preset stations by
following the procedure of the section “To recall a preset
station” on page 9.
To recall a preset station
Simply follow the procedure of the section “To recall a preset
station” on page 9.
TX-580RDS only
* A recalled station is shown by the frequency or station name
on the display.
Notes
●
You can replace a preset station by another FM or AM
station manually by simply following the procedure of the
section “To store stations” on page 9.
●
The automatic preset tuning search will be performed
through all frequencies until stations are stored up to E8. If
the number of received stations is not enough to be stored
up to E8, the search is finished automatically after
searching through all frequencies.
TX-480, TX-480L
●
With this function, only FM stations with sufficient signal
strength are stored automatically. If the station you want
to program is week in signal strength, tune to it in
monaural manually and program it by following the
procedure of the section “To store stations” on page 9.
TX-580RDS
●
With this function, only RDS stations with sufficient signal
strength are stored automatically. If the station you want
to program is weak in signal strength, tune to it in
monaural manually and program it by following the
procedure of the section “To store stations” on page 9.
* There may be a case that this function cannot receive a
station which could be received by the automatic tuning
method. This is because this function receives a large
volume of PI (Program Identification) data along with the
station.
Press and
hold for about
3 seconds.
1
3
2
MEMORY
MAN’L/AUTO FM
MEMORY
AUTO TUNING
TUNING
FM/AM
FM/AM/LW
TX-480, TX-580RDS
TX-480L
FM
* Parts in shaded area are ( )
present on TX-580RDS only.
PRESET
STEREO
0
MHz
40 60
20
l00
1 Select page E.
2
Press and hold for about 3 seconds.
3 Select page A.
4
Listen to the station on A5 to confirm it. If it is not the
station you want, re-select the proper station.
5 Press the same number again.
Lights up.
This shows the exchange of stations is completed.
PRESET
STEREO
0
MHz
40 60
20
l00
MEMORY
11
Flashes.
EXCHANGING PRESET STATIONS
You can exchange the places of two preset stations each other by easy operations.
Flashes.
A/B/C/D/E
PRESET
A/B/C/D/E
PRESET
A/B/C/D/E 1 2345678
PRESET STATIONS
STERE
0
kHZ
MHz
4
20
AUTO
PRESET
STEREO
0
MHz
40 60
20
l00
MEMORY
A/B/C/D/E 1 2345678
PRESET STATIONS
A/B/C/D/E 1 2345678
PRESET STATIONS
Example)
If you want to shift the preset station on E1 to A5, and vice
versa.
TX-480, TX-480L
1, 3 2, 4, 5
12
1 Recall the preset station on E1 (by following the method
of “To recall a preset station” on page 9).
2
3 Next, recall the preset station on A5 by following the
same method with step 1.
4
Lights up.
This shows the exchange of stations is completed.
Example)
If you want to shift the preset station on E1 to A5, and vice
versa.
Press and hold
for about 3
seconds.
Flashes.
Flashes.
4
2
PRESET
PRESET
MH
PS/PTY SEEK
FREQ/PS/PTY
SHIFT
ENTER
PS/PTY SEEK
FREQ/PS/PTY
SHIFT
ENTER
TX-580RDS
RECEIVING RDS STATIONS TX-580RDS only
13
RDS (Radio Data System) is a data transmission system gradually being introduced by FM stations in many countries. Stations
using this system transmit an inaudible stream of data in addition to the normal radio signal.
RDS data contains various information, such as AF (Alternative Frequencies for the same program station), PI (Program
Identification), PS (Program Service station name), PTY (Program Type name), etc.
RDS function is carried out among the network stations.
* This unit utilizes AF, PI, PS and PTY to receive RDS broadcast stations.
Displaying RDS data
This unit can be turned into the following two modes to display RDS data.
PS (Program Service station name) mode:
Displays the name of the RDS station now being received instead of the frequency.
PTY (Program Type name) mode:
Displays the program type of the RDS station now being received. There are 15 program types to classify RDS stations as follows.
News:
Short accounts of facts, events and publicly
expressed views, reportage and actuality.
Current affairs:
Topical program expanding or enlarging
upon the news, generally in different
presentation style or concept, including
documentary debate, or analysis
Information:
Program whose purpose is to impart advice
in the widest sense, including meteorological
reports and forecasts, consumer affairs,
medical help, etc.
Sport:
Program concerned with any aspect of sport.
Education:
Program intended primarily to educate, of
which the formal element is fundamental.
Drama:
All radio plays and serials.
Culture:
Programs concerned with any aspect of
national or regional culture, including
religious affairs, philosophy, social science,
language, theatre, etc.
Science:
Programs about the natural sciences and
technology.
Varied:
Used for mainly speech-based programs
usually of light-entertainment nature, not
covered by above categories. Examples are:
quizzes, panel games, personality interviews,
comedy and satire.
Pop:
Commercial music, which would generally be
considered to be of current popular appeal,
often featuring in current or recent record
sales charts.
Rock:
Contemporary modern music, usually written
and performed by young musicians.
M.O.R.:
(Middle of the Road Music). Common term to
describe music considered to be “easy-
listening”, as opposed to Pop, Rock or
Classical. Music in this category is often but
not always, vocal, and usually of short
duration (<5 min.)
Light classics:
Classical Musical for general, rather than
specialist appreciation. Examples of music in
this category are instrumental music, and
vocal or choral works.
Serious classics:
Performances of major orchestral works,
symphonies, chamber music etc., and
including Grand Opera.
Other music:
Musical styles not fitting into any of the
above categories. Particularly used for
specialist music, of which Jazz, Rhythm &
Blues, Folk, Country, and Reggae are
examples.
BBC R3
NEWS
AFFAIRS
INFO
SPORT
EDUCATE
DRAMA
CULTURE
SCIENCE
VARIED
POP M
ROCK M
MOR M
LIGHT M
CLASSICS
OTHER M
14
To turn the unit into the PS mode or PTY mode
Press the FREQ/PS/PTY button. Whenever pressed, the mode changes into the PS mode, PTY mode and returns to usual mode in
turn.
* When an RDS station is received, the display is automatically turned into the PS mode. Do not press the FREQ/PS/PTY button
until the display is turned into the PS mode. If the button is pressed before the display mode is changed, it may occur that “NO
PS” flashes on the display. This is because the unit has not received all of the RDS data on the station yet.
PS mode The name of the station being received is displayed.
If the station is not an RDS station, “NO PS” flashes on the
display and then returns to usual mode.
PTY mode A program type for the station being received is displayed.
If the RDS station does not employ the PTY data service,
“NO PTY” flashes on the display and then returns to the PS
mode.
If the station is not an RDS station, “NO PTY” flashes on the
display and then returns to usual mode.
Usual mode The frequency of the station being received is displayed.
Note
When PS or PTY data reception is not possible due to poor reception conditions, “NO PS” or “NO PTY” flashes on the display in
each mode. In such a case, press the TUNING MODE button so that “AUTO TUNING” goes off from the display. Though the
reception mode is changed to monaural by this operation, when you changes to the PS or PTY mode, PS or PTY data may be
displayed.
PS/PTY SEEK
FREQ/PS PTY
SHIFT
ENTER
15
1
2 Turn the unit into the PS mode.
* If “NO PS” flashes, proceed to the next step while flashing.
If “NO PS” disappears before you proceed to the next step,
press the FREQ/PS/PTY button again.
3
4 Select the first letter or numeral of the station name.
* By turning the TUNING control, the display will change
letters and numerals in sequence.
* If you will not input the second letter, skip to step 7.
5 When the first letter or numeral of the station name
appears, press the SHIFT button to proceed to the
selection of the next letter or numeral.
6 Repeat steps 4 and 5 for other letters and/or numerals,
if necessary.
7 When inputting the name is finished, press the ENTER
button.
8
The unit begins searching for the station, and it is
continued until the station is found.
You do not have to input a full name for searching
for the station
You may input only the first letter of the station name. If doing
so, you can skip steps 5 and 6. In step 8, the unit searches
for and calls a nearest station which has the letter you input. If
the station is not the desired one, turn the TUNING control
again. The unit will begin searching for another station which
has the same letter.
To cancel this function
Press the AF, FREQ/PS/PTY, SHIFT, ENTER, FM/AM or
MEMORY button.
Notes
●
If no station is found by this function after searching all
preset stations, “NO PS” flashes for about 3 seconds on
the display, and then it returns to the mode which had
been obtained before the searching was performed.
●
This function is useful especially for calling a station with
weak signals which cannot be received by the automatic
tuning method. By only storing such a station, you can call
it any time easily.
Calling a preset RDS station by the station name (PS SEEK)
You can call a desired RDS station stored in this unit by only inputting the name of the station in the PS mode. By this operation,
this unit searches all preset stations for the station. You do not have to input a full name, even only the first letter can be used for
calling. As many as 8 letters and/or numerals can be selected for inputting a name.
4, 8
2
1
7
3, 5
FM/AM
FM
PS/PTY SEEK
FREQ/PS PTY
SHIFT
ENTER
A station name is
displayed or “NO PS”
flashes.
“A” will flash on the second
letter or numeral position.
The name is
illuminated.
Flashes
PS/PTY SEEK
FREQ/PS/PTY
SHIFT
ENTER
PS/PTY SEEK
FREQ/PS/PTY
SHIFT
ENTER
PS/PTY SEEK
FREQ/PS/PTY
SHIFT
ENTER
ENTER
TUNING
TUNING
Slightly turn.
16
Calling a preset RDS station by the program type (PTY SEEK)
By designating a program type, the unit automatically searches all preset stations for RDS stations of that program type.
* There are 15 program types to classify RDS stations. For details, refer to page 13.
1 Turn the unit into the PTY mode.
* If “NO PTY” flashes, proceed to the next step while
flashing. If “NO PTY” disappears before you proceed to the
next step, press the FREQ/PS/PTY button once or twice.
2
3 Select the desired program type.
* By turning the TUNING control, the display will change
program types in sequence.
4 When the desired program type appears, press the
ENTER button.
5
The unit begins searching all preset stations, and calls a
station of the program type if such a station is found.
* When the TUNING control is turned clockwise, the search
is performed from “A1” toward higher numbers of the
preset stations (A1, A2 ... A8, B1, B2, ...). If, however,
“A3” is currently being called for example, the search
begins from the next station “A4”.
When the TUNING control is turned counterclockwise, the
search is performed in reverse order.
If the called station is not the desired one, turn the TUNING
control again to search for another station of the same
program type.
To cancel this function
Press the AF, FREQ/PS/PTY, SHIFT, ENTER, FM/AM or
MEMORY button.
Note
If no station is found by this function, after searching all preset
stations, “NO PTY” flashes for about 3 seconds on the
display, and then it returns to the mode which had been
obtained before the searching was performed.
3, 5
1
4
2
PS/PTY SEEK
FREQ/PS PTY
SHIFT
ENTER
Press once or twice
until a program type is
displayed or “NO PTY”
flashes.
PS/PTY SEEK
FREQ/PS/PTY
SHIFT
ENTER
The program type of the station now being
received or “NEWS” flashes on the display.
PS/PTY SEEK
FREQ/PS/PTY
SHIFT
ENTER
ENTER
Flashes.
TUNING
TUNING
Slightly turn.
17
Calling the best quality RDS station which broadcasts the
same program (AF SEEK)
This function automatically searches for and calls another RDS station of the best reception quality which broadcasts the same
program now you are listening to.
This function utilizes AF (Alternative Frequencies for the same program station) and PI (Program Identification) of RDS data service.
The search is carried out among the RDS network stations.
1 Tune to a desired RDS station.
* Wait for about 10 seconds before proceeding to the
next step. This is for making this unit carry out
searching more stations.
2
The unit searches network stations for other stations with the
same program.
* If the station is not an RDS station, or there is no other
station with the same program, “NO AF” flashes.
Stations with the same program are all stored and
numbered from the best quality station in sequence.
When the search is finished, the best quality station is
called.
3 If desired, you can call the second station by pressing
the AF button.
Whenever the AF button is pressed, stored stations are
called in sequence.
When pressed after the last station is selected, the first one
is restored.
To cancel this function
Press a button other than the AF button.
All of the stored stations will be also cleared.
AF
AF
2, 3
18
TROUBLESHOOTING
If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple
measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and
contact your authorized YAMAHA dealer or service center for help.
SYMPTOM
Crackling sounds from time to time
(especially in weak signal areas).
FM stereo reception is noisy.
The STEREO indicator flickers and
reception is noisy.
There is distortion and clear reception
cannot be obtained even with a good FM
antenna.
No stereo effect even with a stereo
broadcast.
A desired station cannot be tuned in with
Automatic tuning.
Previously preset stations can no longer
be tuned in.
Insufficient sensitivity.
A desired station cannot be tuned in with
Automatic tuning.
There are continuous crackling and
hissing noises.
There are buzzing and whining noises
(especially in the evening).
CAUSE
Ignition noise from passing vehicles.
Noise from thermostats or other electrical
equipment.
Because of the characteristics of FM stereo
broadcasts, this is limited to cases where
the transmitter is far away or the antenna
input is poor.
Insufficient antenna input.
Not tuned correctly.
There is multipath interference.
The TUNING MODE button is set to the
manual tuning mode.
The station is too weak.
The tuner has been unplugged for a long
period.
Weak signal or loose antenna connections.
These noises result from lightning,
fluorescent lamps, motors, thermostats and
other electrical equipment.
Another station is interfering with the
received station.
A television set is being used nearby.
REMEDY
The FM antenna should be put up as high
as possible, away from the road, and a
coaxial cable used.
Attach a noise suppressor to the equipment
causing the noise.
Check the antenna connections.
Try using a high quality directional FM
antenna.
Set the TUNING MODE button to the
manual tuning mode.
Use an antenna appropriate for the
reception condition in your area.
Tune again.
Adjust antenna placement to eliminate multi-
path interference.
Set the button properly.
Use the manual tuning mode.
Use a high quality directional FM antenna.
Repeat the presetting procedure.
Tighten the AM loop antenna connections
and rotate it for best reception.
Use the manual tuning mode.
Use an outdoor antenna and a ground wire.
This will help somewhat but it is difficult to
eliminate all noises.
This is impossible to remedy.
Relocate this unit away from the TV.
FM
AM
19
SPECIFICATIONS
FM SECTION
Tuning Range
[U.S.A. and Canada models]...................87.5 to 107.9 MHz
[U.K., Australia, Europe and General models]
..................................................................87.5 to 108 MHz
50 dB Quieting Sensitivity (IHF) [Except Europe model]
75 ohms Mono ..........................................1.6 µV (15.3 dBf)
75 ohms Stereo ..........................................21 µV (37.7 dBf)
Usable Sensitivity
[Except Europe model]
75 ohms, 1 kHz, 100% mod. (30 dB S/N Quieting)
...................................................................0.8 µV (9.3 dBf)
[Europe model] (DIN)
75 ohms Mono (S/N 26 dB)......................................0.9 µV
75 ohms Stereo (S/N 46 dB) .....................................24 µV
Image Response Ratio
[Except Europe model] ................................................45 dB
[Europe model] ............................................................80 dB
IF Response Ratio
<TX-480, TX-480L>......................................................70 dB
<TX-580RDS>..............................................................80 dB
Spurious Response Ratio..................................................70 dB
AM Suppression Ratio.......................................................55 dB
Capture Ratio ...................................................................1.5 dB
Alternate Channel Selectivity
[Except Europe model] ................................................85 dB
Selectivity (two signals, 40 kHz Dev., ±300 kHz)
[Europe model only].....................................................70 dB
Signal-to-Noise Ratio
[Except Europe model] (IHF)
Mono..........................................................................82 dB
Stereo........................................................................76 dB
[Europe model] (DIN-weighted)
Mono (40 kHz Dev.)...................................................75 dB
Stereo (40 kHz Dev.) ................................................70 dB
Harmonic Distortion (1 kHz)
[Except Europe model]
Mono/Stereo......................................................0.1%/0.2%
[Europe model (40 kHz Dev.)]
Mono/Stereo......................................................0.1%/0.2%
Stereo Separation
[Except Europe model]......................................1 kHz 52 dB
[Europe model (40 kHz Dev.)]...........................1 kHz 45 dB
Frequency Response
30 Hz to 15 kHz....................................................0±0.5 dB
AM (MW) SECTION
Tuning Range
[U.S.A.,Canada and General models]........530 to 1,710 kHz
[U.K., Australia and Europe models]..........531 to 1,611 kHz
Usable Sensitivity
<TX-480, TX-480L>................................................200 µV/m
<TX-580RDS>........................................................100 µV/m
Selectivity ..........................................................................32 dB
Signal-to-Noise Ratio.........................................................50 dB
Image Response Ratio......................................................40 dB
Spurious Response Ratio..................................................50 dB
Harmonic Distortion; 400 Hz...............................................0.3%
AM (LW) SECTION <TX-480L only>
Tuning Range.....................................................153 to 288 kHz
Usable Sensitivity........................................................400 µV/m
Selectivity ..........................................................................32 dB
Signal-to-Noise Ratio.........................................................50 dB
Image Response Ratio......................................................30 dB
Spurious Response Ratio..................................................45 dB
Harmonic Distortion; 400 Hz...............................................0.3%
AUDIO SECTION
<TX-480, TX-480L>
Output Level/Impedance
FM (100 % mod. 1 kHz)
[Except Europe model] ........................550 mV/2.2 k-ohms
[Europe model (40 kHz Dev.)] .............400 mV/2.2 k-ohms
AM (30% mod. 400 Hz)
[Except Europe model] ........................180 mV/2.2 k-ohms
[Europe model] ....................................150 mV/2.2 k-ohms
<TX-580RDS>
Output Level/Impedance
FM (100 % mod. 1 kHz)
[U.K. model].........................................600 mV/2.2 k-ohms
[Europe model (40 kHz Dev.)] .............600 mV/2.2 k-ohms
AM (30% mod. 400 Hz)
[U.K. model].........................................200 mV/2.2 k-ohms
[Europe model] ....................................150 mV/2.2 k-ohms
GENERAL
Power Supply
[U.S.A. and Canada models].............................120V, 60 Hz
[Europe model]..................................................230V, 50 Hz
[U.K. and Australia models]...............................240V, 50 Hz
[General model] ......................110-120/220-240V, 50/60 Hz
Power Consumption
<TX-480, TX-480L>..........................................................7W
<TX-580RDS>................................................................10W
Dimensions (W x H x D)...............................435 x 86 x 294 mm
(17-1/8” x 3-3/8” x 11-9/16”)
Weight..........................................................3.2 kg (7 lbs. 1 oz.)
Accessories.............................................Audio connection cord
AM loop antenna
Indoor FM antenna
* Specifications subject to change without notice.
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, D-2084 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. 17 RUE DES CAMPANULES, LOGNES 77321 MARNE LA VALLEE CEDEX 2, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
in andere talen
- English: Yamaha 480 User manual
- italiano: Yamaha 480 Manuale utente
- русский: Yamaha 480 Руководство пользователя
- français: Yamaha 480 Manuel utilisateur
- español: Yamaha 480 Manual de usuario
- Deutsch: Yamaha 480 Benutzerhandbuch
- português: Yamaha 480 Manual do usuário
- dansk: Yamaha 480 Brugermanual
- suomi: Yamaha 480 Ohjekirja
- čeština: Yamaha 480 Uživatelský manuál
- svenska: Yamaha 480 Användarmanual
- Türkçe: Yamaha 480 Kullanım kılavuzu
- polski: Yamaha 480 Instrukcja obsługi
- română: Yamaha 480 Manual de utilizare