Zebra LI3608 Snelstartgids

Type
Snelstartgids
LI3608
Quick Start Guide
Linear Imager Scanner
2 LI3608 Quick Start Guide
Zebra reserves the right to make changes to any product to improve reliability, function, or design. Zebra does not
assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or
application described herein. No license is granted, either expressly or by implication, estoppel, or otherwise under any
patent right or patent, covering or relating to any combination, system, apparatus, machine, material, method, or
process in which Zebra products might be used. An implied license exists only for equipment, circuits, and subsystems
contained in Zebra products.
Warranty
For the complete Zebra hardware product warranty statement, go to: www.zebra.com/warranty.
For Australia Only
For Australia Only. This warranty is given by Zebra Technologies Asia Pacific Pte. Ltd., 71 Robinson Road, #05-02/03,
Singapore 068895, Singapore. Our goods come with guarantees that cannot be excluded under the Australia
Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to
be of acceptable quality and the failure does not amount to a major failure.
Zebra Technologies Corporation Australia’s limited warranty above is in addition to any rights and remedies you may
have under the Australian Consumer Law. If you have any queries, please call Zebra Technologies Corporation at +65
6858 0722. You may also visit our website: www.zebra.com for the most updated warranty terms.
Service Information
If you have a problem using the equipment, contact your facility’s Technical or Systems Support. If there is a problem
with the equipment, they will contact the Zebra Global Customer Support Center at: www.zebra.com/support.
For the latest version of this guide go to: www.zebra.com/support.
LI3608 Quick Start Guide 3
Introduction
The LI3608 linear imager combines excellent scanning performance and advanced ergonomics to provide the best
value in a lightweight laser scanner, ensuring comfort and ease of use for extended periods of time.
Features
Accessories
4 LI3608 Quick Start Guide
Cable Attachment
1. Insert cable fully so that the connector is flush with the scanner surface.
2. Loosen metal lock plate screws using a PH1 driver.
3. Slide lock plate to fully locked position.
4. Tighten screw using a PH1 driver (torque: 5 in-lb.).
LI3608 Quick Start Guide 5
Connect Host Interface
USB
The digital scanner automatically detects the host interface type and uses the default setting. If the default (*) does not
meet your requirements, scan another host bar code below.
*USB KEYBOARD (HID)
USB CDC HOST
6 LI3608 Quick Start Guide
USB (continued)
IBM TABLE TOP USB
IBM HAND-HELD USB
SNAPI WITHOUT IMAGING
SNAPI WITH IMAGING
USB OPOS HAND-HELD
SSI OVER USB CDC
SIMPLE COM PORT EMULATION
LI3608 Quick Start Guide 7
RS-232
*STANDARD RS-232
ICL RS-232
NIXDORF RS-232 MODE A
NIXDORF RS-232 MODE B
8 LI3608 Quick Start Guide
RS-232 (continued)
Keyboard Wedge
FUJITSU RS-232
OPOS/JPOS
*IBM AT NOTEBOOK
IBM PC/AT and IBM PC COMPATIBLE
LI3608 Quick Start Guide 9
IBM 46XX
NON-IBM SCANNER EMULATION (PORT 5B)
HAND-HELD SCANNER EMULATION (PORT 9B)
TABLE-TOP SCANNER EMULATION (PORT 17)
10 LI3608 Quick Start Guide
Set Defaults Bar Code
RETURN TO FACTORY DEFAULTS
Enter Key Bar Code (Carriage Return/Line Feed)
Add an Enter key after scanned data.
ADD AN ENTER KEY (CARRIAGE RETURN/LINE FEED)
Tab Key Bar Code
Add a Tab key after scanned data.
ADD A TAB KEY
USB Caps Lock Override
USB - OVERRIDE CAPS LOCK KEY (ENABLE)
*USB - DO NOT OVERRIDE CAPS LOCK KEY (DISABLE)
LI3608 Quick Start Guide 11
Aiming
Cover the entire bar code with the aiming pattern to ensure it is within the field of view.
LI3608-SR
LI3608-ER
LED Indications
Beeper Indications
Indication LED
Hand-Held Scanning
The scanner is on and ready to scan, or no power to the scanner Off
A bar code is successfully decoded Green
Transmission error Red
Hand-Free (Presentation) Scanning
No power to the scanner Off
The scanner is on and ready to scan Green
A bar code is successfully decoded Off momentarily
Transmission error Red
Indication Beeper Sequence
Power up Low/medium/high beep
A bar code is successfully decoded Medium beep
Transmission error detected; data is ignored 4 long low beeps
Successful parameter setting High/low/high/low beep
Correct programming sequence performed High/low beep
Incorrect programming sequence, or
Cancel
bar code scanned Low/high beep
012345
012345
12 LI3608 Quick Start Guide
Troubleshooting
123Scan
2
123Scan2 is an easy-to-use, PC-based software tool that enables rapid and easy customized setup of a scanner via a
bar code or USB cable.
Utility Functionality:
Device Configuration
Electronic Programming (USB Cable)
Programming Bar Code(s)
Data View – Scan Log (Display Scanned Bar Code Data)
Access Asset Tracking Information
Upgrade Firmware and View Release Notes
Remote Management (SMS Package Generation)
For more information, visit: www.zebra.com/123Scan.
Problem Possible Causes Possible Solutions
Scanner not working. No power to scanner. Check system power.
Scanner is disabled. Ensure that correct host interface
cable is used.
Scanner decoding bar code, but data not
transmitting to host.
Host interface not configured
properly.
Scan appropriate host parameter bar
codes.
Interface cable is loose. Ensure all cable connections are
secure.
Invalid ADF rule. Program the correct ADF rules.
Scanner not decoding bar code. Scanner not programmed for bar
code type.
Ensure scanner is programmed to
read type of bar code being scanned.
Bar code unreadable. Ensure bar code is not defaced; try
scanning test bar code of same bar
code type.
Distance between scanner and
bar code incorrect.
Move scanner closer to, or further
from bar code.
Scanned data incorrectly displayed on
host.
Host interface not configured
properly.
Scan appropriate host parameter bar
codes.
Region improperly configured. Select appropriate country and
language encoding scheme.
LI3608 Quick Start Guide 13
Regulatory Information
This device is approved under Zebra Technologies Corporation.
This guide applies to Model Number: LI3608. All Zebra devices are designed to be compliant with rules and regulations
in locations they are sold and will be labeled as required. Local language translations are available at the following
website: www.zebra.com/support.
Any changes or modifications to Zebra equipment, not expressly approved by Zebra, could void the user’s authority to
operate the equipment.
Health and Safety Recommendations
Ergonomic Recommendations
Caution: In order to avoid or minimize the potential risk of ergonomic injury follow the recommendations
below. Consult with your local Health & Safety Manager to ensure that you are adhering to your company's safety
programs to prevent employee injury.
Reduce or eliminate repetitive motion
Maintain a natural position
Reduce or eliminate excessive force
Keep objects that are used frequently within easy reach
Perform tasks at correct heights
Reduce or eliminate vibration
Reduce or eliminate direct pressure
Provide adjustable workstations
Provide adequate clearance
Provide a suitable working environment
Improve work procedures.
Laser Devices
Class 2 laser scanners use a low power, visible light diode. As with any very bright light source such as the sun, the
user should avoid staring directly into the light beam. Momentary exposure to a Class 2 laser is not known to be
harmful.
Caution: Use of controls, adjustments, or the performance of procedures other than those specified herein
may result in hazardous laser light exposure.
Labels Read:
1. Laser Light - do not stare into beam Class 2 Laser product.
2. Caution - Class 2 laser light when open. Avoid direct eye exposure.
3. Complies with 21 CFR1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated June 24,
2007, and IEC/EN 60825-1:2014.
LED Safety
Classified as Exempt Risk Group per IEC 62471:2006 (Ed. 1.0); EN 62471:2008.
Max Pulse Duration: 12 ms.
14 LI3608 Quick Start Guide
Radio Frequency Interference Requirements - FCC
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
Consult the dealer or an experienced radio/TV technician for help.
Radio Frequency Interference Requirements - Canada
CAN ICES-3(B)/NMB-3(B)
Marking and European Economic Area (EEA)
Statement of Compliance
Zebra hereby declares that this device is in compliance with all applicable Directives, 2014/30/EU, 2014/35/EU and
2011/65/EU. The full text of the EU Declaration of Conformity is available at the following internet address:
www.zebra.com/doc.
CAUTION- CLASS 2 LASER LIGHT WHEN OPEN. DO NOT
STARE INTO THE BEAM. ATTENTION- LUMIÉRE LASER
EN CAS D'OUVERTURE. NE PAS REGARDER DANS LE FAISCEAU.
VORSICHT- LASERLICHT KLASSE 2, WENN ABDECKUNG GEÖFFNET.
NICHT IN DEN STRAHL BLICKEN.
ព㸸ᡴᔰᰦ㚄䬱ኻᩀ᭷⃭ගᑕ໚ග᮰
NOTE:
LI3608-SR - Label not applicable.
LI3608 Quick Start Guide 15
Other Countries
Japan (VCCI) - Voluntary Control Council for Interference
Class B ITE
Korea Warning Statement for Class B ITE
Chile
Este equipo cumple con la Resolución No 403 de 2008, de la Subsecretaria de telecomunicaciones, relativa a
radiaciones electromagnéticas.
China
www.zebra.com/contact
Ukraine
Eurasian Customs Union
Евразийский Таможенный Союз
Данный продукт соответствует требованиям знака EAC.
16 LI3608 Quick Start Guide
Waste Electrical and Electronic Equipment (WEEE)
Bulgarish: За клиенти от ЕС: След края на полезния им живот всички продукти трябва да се връщ ат на Zebra за рециклиране. За
информация относно връщането на продукти, моля отидете на адрес www.zebra.com/weee.
Čeština: Pro zákazníky z EU: Všechny produkty je nutné po skončení jejich životnosti vrátit společnosti Zebra k recyklaci. Informace o způsobu
vrácení produktu najdete na webové stránce: www.zebra.com/recycling/weee.
Dansk: Til kunder i EU: Alle produkter skal returneres til Zebra til recirkulering, når de er udtjent. Læs oplysningerne om returnering af produkter på:
www.zebra.com/recycling/weee.
Deutsch: Für Kunden innerhalb der EU: Alle Produkte müssen am Ende ihrer Lebensdauer zum Recycling an Zebra zurückgesandt werden.
Informationen zur Rücksendung von Produkten finden Sie unter www.zebra.com/recycling/weee.
Ελληνικά: Για πελάτες στην Ε.Ε.: Όλα τα προϊόντα, στο τέλος της διάρκειας ζωής τους, πρέπει να επιστρ έφονται στην Zebra για ανακύκλωση. Για
περισσότερες πληροφορίες σχετικά με την επιστροφή ενός προϊόντος, επισκεφθείτε τη διεύθυνση www.zebra.com/recycling/weee στο Διαδίκτυο.
English: For EU Customers: All products at the end of their life must be returned to Zebra for recycling. For information on how to return product,
please go to: www.zebra.com/recycling/weee.
Español: Para clientes en la Unión Europea: todos los productos deberán entregarse a Zebra al final de su ciclo de vida para que sean reciclados.
Si desea más información sobre cómo devolver un producto, visite: www.zebra.com/recycling/weee.
Eesti: EL klientidele: kõik tooted tuleb nende eluea lõppedes tagastada taaskasutamise eesmärgil Zebra'ile. Lisainformatsiooni saamiseks toote
tagastamise kohta külastage palun aadressi: www.zebra.com/recycling/weee.
Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on palautettava kierrätettäväksi Zebra-yhtiöön, kun tuotetta ei enää käytetä. Lisätietoja
tuotteen palauttamisesta on osoitteessa www.zebra.com/recycling/weee.
Français : Clients de l'Union Européenne : Tous les produits en fin de cycle de vie doivent être retournés à Zebra pour recyclage. Pour de plus
amples informations sur le retour de produits, consultez : www.zebra.com/recycling/weee.
Magyar: Az EU-ban vásárlóknak: Minden tönkrement terméket a Zebra vállalathoz kell eljuttatni újrahasznosítás céljából. A termék
visszajuttatásának módjával kapcsolatos tudnivalókért látogasson el a www.zebra.com/recycling/weee.
Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del rispettivo ciclo di vita devono essere restituiti a Zebra al fine di consentirne
il riciclaggio. Per informazioni sulle modalità di restituzione, visitare il seguente sito Web:
www.zebra.com/recycling/weee.
Lietuvių: ES vartotojams: visi gaminiai, pasibaigus jų eksploatacijos laikui, turi būti grąžinti utilizuoti į kompaniją „Zebra“. Daugiau informacijos, kaip
grąžinti gaminį, rasite: www.zebra.com/recycling/weee.
Latviešu: ES klientiem: visi produkti pēc to kalpošanas mūža beigām ir jānogādā atpakaļ Zebra otrreizējai pārstrādei. Lai iegūtu inform
āciju par
produktu nogādāšanu Zebra, lūdzu, skatiet: www.zebra.com/recycling/weee.
Malti: Għal klijenti fl-UE: il-prodotti kollha li jkunu waslu fl-aħħar tal-ħajja ta' l-użu tagħhom, iridu jiġu rritornati għand Zebra għar-riċiklaġġ. Għal aktar
tagħrif dwar kif għandek tirritorna l-prodott, jekk jogħġbok żur: www.zebra.com/recycling/weee.
Nederlands: Voor klanten in de EU: alle producten dienen aan het einde van hun levensduur naar Zebra te worden teruggezonden voor recycling.
Raadpleeg www.zebra.com/recycling/weee voor meer informatie over het terugzenden van producten.
Polski: Klienci z obszaru Unii Europejskiej: Produkty wycofane z eksploatacji naleźy zwrócić do firmy Zebra w celu ich utylizacji. Informacje na temat
zwrotu produktów znajdują się na stronie internetowej www.zebra.com/recycling/weee.
Português: Para clientes da UE: todos os produtos no fim de vida devem ser devolvidos à Zebra para reciclagem. Para obter informações sobre
como devolver o produto, visite: www.zebra.com/recycling/weee.
Românesc: Pentru clienţii din UE: Toate produsele, la sfârşitul duratei lor de funcţionare, trebuie returnate la Zebra pentru reciclare. Pentru
informaţii despre returnarea produsului, accesaţi: www.zebra.com/recycling/weee.
Slovenčina: Pre zákazníkov z krajín EU: Všetky výrobky musia byť po uplynutí doby ich životnosti vrátené spoločnosti Zebra na recykláciu. Bližšie
informácie o vrátení výrobkov nájdete na: www.zebra.com/recycling/weee.
Slovenski: Za kupce v EU: vsi izdelki se morajo po poteku življenjske dobe vrniti podjetju Zebra za reciklažo. Za informacije o vračilu izdelka
obiščite: www.zebra.com/recycling/weee.
Svenska: För kunder inom EU: Alla produkter som uppnått sin livslängd måste returneras till Zebra för återvinning. Information om hur du returnerar
produkten finns på www.zebra.com/recycling/weee.
Türkçe: AB Müşterileri için: Kullanım süresi dolan tüm ürünler geri dönüştürme için Zebra'ya iade edilmelidir. Ürünlerin nasıl iade edileceği hakkında
bilgi için lütfen şu adresi ziyaret edin: www.zebra.com/recycling/weee.
TURKISH WEEE Statement of Compliance
EEE Yönetmeligine Uygundur
LI3608 Quick Start Guide 17
China RoHS
MN002166A03EN Revision A - March 2018
Zebra Technologies Corporation
Lincolnshire, IL U.S.A.
www.zebra.com
©2018 ZIH Corp. and/or its affiliates. All rights reserved. ZEBRA and the stylized Zebra head are
trademarks of ZIH Corp., registered in many jurisdictions worldwide. All other trademarks are the
property of their respective owners.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18

Zebra LI3608 Snelstartgids

Type
Snelstartgids