Lovibond 00386479 - MD1x0/200 - Alkalinity-m T, Chlorine HR T, Chlorine L, Chlorine T, Copper T, CyA T, Iron T, pH value L, pH-value T Handleiding

Merk: Lovibond

Model: 00386479 - MD1x0/200 - Alkalinity-m T, Chlorine HR T, Chlorine L, Chlorine T, Copper T, CyA T, Iron T, pH value L, pH-value T

Type: Handleiding

Lovibond® Water Testing

Tintometer® Group

Manual of Methods

MD 100 • MD 110 • MD 200

Manual of Methods

Page 4

Methodenhandbuch

Seite 58

Manual de Métodos

Página 112

Méthodes Manuel

Page 166

Manuale dei Metodi

Pagina 220

Métodos Manual

Página 274

Handboek Methoden

Zijde 328

方法手册

Page 382

NL Handboek van Methoden 01/20EN Handbook of Methods 01/20

KS4.3 T

0.1 - 4 mmol/l KS4.3

Acid / Indicator

S:4.3

Instrument specific information

The test can be performed on the following devices. In addition, the required cuvette

and the absorption range of the photometer are indicated.

Instrument Type Cuvette λMeasuring Range

MD 200, MD 600, MD 610,

MD 640, MultiDirect, PM 620,

PM 630

ø 24 mm 610 nm 0.1 - 4 mmol/l KS4.3

SpectroDirect, XD 7000,

XD 7500

ø 24 mm 615 nm 0.1 - 4 mmol/l KS4.3

Material

Required material (partly optional):

Reagents Packaging Unit Part Number

Alka-M-Photometer Tablet / 100 513210BT

Alka-M-Photometer Tablet / 250 513211BT

Application List

• Waste Water Treatment

• Drinking Water Treatment

• Raw Water Treatment

Notes

1. The terms Alkalinity-m, m-Value, total alkalinity and Acid demand to KS4.3 are iden-

tical.

2. For accurate results, exactly 10 ml of water sample must be used for the test.

Display in the MD

100 / MD 110 /

MD 200

Bar code for the

detection of the

methods

Method name

Measuring range

Chemical Method

Method number

Language codes

ISO 639-1 Revision status

KS4.3 T / 20

How to use

ENMethod Reference Book4

Implementation of the provision Acid capacity KS4.3 with Tablet

Select the method on the device

For this method, no ZERO measurements are to be carried out with the following de-

vices: XD 7000, XD 7500

10 ml

Fill 24 mm vial with 10 ml

sample.

Close vial(s).

Sample

Place sample vial in the

sample chamber. • Pay

attention to the positioning.

Dissolve tablet(s) by inver-

ting.

Sample

Place sample vial in the

sample chamber. • Pay

attention to the positioning.

Test

Press the TEST (XD:

START) button.

The result in Acid Capacity KS4.3 appears on the display.

Performing test

procedure

KS4.3 T / 20

NL Handboek van Methoden 01/20EN Handbook of Methods 01/20

How to use

ENMethod Reference Book 5

Alkalinity-m T / M30

ENMethod Reference Book1.06

Alkalinity-m T M30

5 - 200 mg/L CaCO3tA

Acid / Indicator

Material

Required material (partly optional):

Reagents Packaging Unit Part Number

Alka-M-Photometer Tablet / 100 513210BT

Alka-M-Photometer Tablet / 250 513211BT

Remarks

1. The terms Alkalinity-m, m-Value, total alkalinity and Acid demand to KS4.3 are

identical.

2. For accurate results, exactly 10 ml of water sample must be used for the test.

Alkalinity-m T / M30

ENMethod Reference Book1.0 7

Determination of Alkalinity, total = Alkalinity-m = m-Value with

Tablet

Select the method on the device.

10 mL

Sample

Fill 24 mm vial with 10 mL

sample.

Close vial(s). Place sample vial in the

sample chamber. Pay

attention to the positioning.

Zero

Press the ZERO button. Remove the vial from the

sample chamber.

24 mm

Add ALKA-M-

PHOTOMETER tablet.

Crush tablet(s) by rotating

slightly.

Close vial(s).

Alkalinity-m T / M30

ENMethod Reference Book1.08

Sample

Test

Dissolve tablet(s) by

inverting.

Place sample vial in the

sample chamber. Pay

attention to the positioning.

Press the TEST (XD:

START)button.

The result in Alkalinity-m appears on the display.

Alkalinity-m T / M30

ENMethod Reference Book1.0 9

Analyses

The following table identifies the output values can be converted into other citation

forms.

Unit Cite form Scale Factor

mg/l CaCO31

°dH 0.056

°eH 0.07

°fH 0.1

°aH 0.058

KS4.3 0.02

Chemical Method

Acid / Indicator

Appendix

Derived from

EN ISO 9963-1

Chlorine T / M100

ENMethod Reference Book1.010

Chlorine T M100

0.01 - 6.0 mg/L Cl2 a) CL6

DPD

Material

Required material (partly optional):

Reagents Packaging Unit Part Number

DPD No.1 Tablet / 100 511050BT

DPD No. 1 Tablet / 250 511051BT

DPD No. 1 Tablet / 500 511052BT

DPD No. 3 Tablet / 100 511080BT

DPD No. 3 Tablet / 250 511081BT

DPD No. 3 Tablet / 500 511082BT

DPD No. 1 High Calcium e) Tablet / 100 515740BT

DPD No. 1 High Calcium e) Tablet / 250 515741BT

DPD No. 1 High Calcium e) Tablet / 500 515742BT

DPD No. 3 High Calcium e) Tablet / 100 515730BT

DPD No. 3 High Calcium e) Tablet / 250 515731BT

DPD No. 3 High Calcium e) Tablet / 500 515732BT

DPD No. 4 Tablet / 100 511220BT

DPD No. 4 Tablet / 250 511221BT

DPD No. 4 Tablet / 500 511222BT

DPD No. 3 Evo Tablet / 100 511420BT

DPD No. 3 Evo Tablet / 250 511421BT

DPD No. 3 Evo Tablet / 500 511422BT

DPD No. 4 Evo Tablet / 100 511970BT

DPD No. 4 Evo Tablet / 250 511971BT

DPD No. 4 Evo Tablet / 500 511972BT

Available Standards

Title Packaging Unit Part Number

ValidCheck Chlorine 1,5 mg/l 1 Pieces 48105510

Chlorine T / M100

ENMethod Reference Book1.0 11

Sampling

1. When preparing the sample, chlorine outgassing, e.g. through the pipette or

shaking, must be avoided.

2. The analysis must take place immediately after taking the sample.

Preparation

1. Cleaning of vials:

As many household cleaners (e.g. dishwasher detergent) contain reducing

substances, this can lead to lower results with the determination of chlorine.

To avoid measurement errors, the glassware used should be free of chlorine

consumption. To achieve this, all glassware should be placed in a sodium

hypochlorite solution (0.1 g/L) for one hour and then rinsed thoroughly with

deionised water.

2. For individual testing of free and total chlorine, the use of different sets of

glassware is recommended (EN ISO 7393-2, 5.3)

3. The DPD colour development is carried out at a pH value of 6.2 to 6.5. The

reagents therefore contain a buffer for the pH adjustment. Strong alkaline or acidic

water samples must therefore be adjusted between pH 6 and pH 7 before the

analysis (use 0.5 mol/Lsulphuric acid or 1 mol/Lsodium hydroxide).

Remarks

1. Evotablets can be used as an alternative to the corresponding standard tablet (e.g.

DPD No.3 Evoinstead of DPD No.3).

Chlorine T / M100

ENMethod Reference Book1.012

Determination of free chlorine with tablet

Select the method on the device.

10 mL

Sample

Fill 24 mm vial with 10 mL

sample.

Close vial(s). Place sample vial in the

sample chamber. Pay

attention to the positioning.

Zero

Press the ZERO button. Remove the vial from the

sample chamber.

Empty vial except for a few

drops.

24 mm

Add DPD No. 1 tablet . Crush tablet(s) by rotating

slightly.

Fill up vial with sample to the

10 mL mark.

Chlorine T / M100

ENMethod Reference Book1.0 13

Sample

Close vial(s). Dissolve tablet(s) by

inverting.

Place sample vial in the

sample chamber. Pay

attention to the positioning.

Test

Press the TEST (XD:

START)button.

The result in mg/L free chlorine appears on the display.

Determination of total Chlorine with tablet

Select the method on the device.

10 mL

Sample

Fill 24 mm vial with 10 mL

sample.

Close vial(s). Place sample vial in the

sample chamber. Pay

attention to the positioning.

Chlorine T / M100

ENMethod Reference Book1.014

Zero

Press the ZERO button. Remove the vial from the

sample chamber.

Empty vial except for a few

drops.

Add DPD No. 1 tablet . Add DPD No. 3 tablet .As an alternative to DPD

No. 1 and No. 3 tablets, a

DPD No. 4 tablet can be

added.

24 mm

Crush tablet(s) by rotating

slightly.

Fill up vial with sample to

the 10 mL mark.

Close vial(s).

Chlorine T / M100

ENMethod Reference Book1.0 15

Sample

Test

Dissolve tablet(s) by

inverting.

Place sample vial in the

sample chamber. Pay

attention to the positioning.

Press the TEST (XD:

START)button.

11 12

2 min

Wait for 2 minute(s)

reaction time.

Once the reaction period is finished, the measurement takes place automatically.

The result in mg/L total Chlorine appears on the display.

Chlorine T / M100

ENMethod Reference Book1.016

Chemical Method

DPD

Appendix

Interferences

Persistant Interferences

• All oxidising agents in the samples react like chlorine, which leads to higher results.

Removeable Interferences

• Interference from copper and iron (III) are eliminated by the addition of EDTA.

• The use of reagent tablets in samples with high calcium content* and/or

high conductivity* can lead to turbidity of the sample and therefore incorrect

measurements. In this case, the alternative reagent tablet DPD No.1 High Calcium

and reagent tablet DPD No.3 High Calcium should be used.

*it is not possible to give exact values, because the development of turbidity depends

on the composition and nature of the sample.

• Concentrations above 10 mg/L chlorine, in the event of using fluid reagents, can

lead to results within the measuring range of up to 0 mg/L. In the event of a high

concentration of chlorine, the sample must be diluted with chlorine-free water. 10

mLof the diluted sample should be mixed with the reagent and the measurement

taken again (plausibility test).

Interference from / [mg/L]

CrO4 2- 0.01

MnO20.01

Method Validation

Limit of Detection 0.02 mg/L

Limit of Quantification 0.06 mg/L

End of Measuring Range 6 mg/L

Sensitivity 2.05 mg/L / Abs

Confidence Intervall 0.04 mg/L

Standard Deviation 0.019 mg/L

Variation Coefficient 0.87 %

Conformity

EN ISO 7393-2

Chlorine T / M100

ENMethod Reference Book1.0 17

a) determination of free, combined and total | e) alternative reagent, used instead of DPD No.1/No.3 in case of turbidity

in the water sample caused by high concentration of calcium and/or high conductivity

Chlorine L / M101

ENMethod Reference Book1.018

Chlorine L M101

0.02 - 4.0 mg/L Cl2 a) CL6

DPD

Material

Required material (partly optional):

Reagents Packaging Unit Part Number

DPD 1 Buffer Solution, Blue Bottle 15 mL 471010

DPD 1 Buffer Solution 100 mL 471011

DPD 1 Buffer Solution 1 Pieces 471016

DPD 1 Reagent Solution, Green Bottle 15 mL 471020

DPD 1 Reagent Solution 100 mL 471021

DPD 1 Reagent Solution 1 Pieces 471026

DPD 3 Solution, Red Bottle 15 mL 471030

DPD 3 Solution 100 mL 471031

DPD 3 Solution 1 Pieces 471036

DPD Reagent Set 1 Pieces 471056

Available Standards

Title Packaging Unit Part Number

ValidCheck Chlorine 1,5 mg/l 1 Pieces 48105510

Sampling

1. When preparing the sample, Chlorine outgassing, e.g. through the pipette or

shaking, must be avoided.

2. The analysis must take place immediately after taking the sample.

Chlorine L / M101

ENMethod Reference Book1.0 19

Preparation

1. Cleaning of vials:

As many household cleaners (e.g. dishwasher detergent) contain reducing

substances, this can lead to lower results with the determination of Chlorine.

To avoid measurement errors, the glassware used should be free of chlorine

consumption. To achieve this, all glassware should be placed in a sodium

hypochlorite solution (0.1 g/L) for one hour and then rinsed thoroughly with

deionised water.

2. For individual testing of free and total Chlorine, the use of different sets of

glassware is recommended (EN ISO 7393-2, 5.3)

3. The DPD colour development is carried out at a pH value of 6.2 to 6.5. The

reagents therefore contain a buffer for the pH adjustment. Strong alkaline or acidic

water samples must therefore be adjusted between pH 6 and pH 7 before the

analysis (use 0.5 mol/l Sulphuric acid or 1 mol/l Sodium hydroxide).

Remarks

1. After use, ensure the cuvettes are once again closed with the respective same-

coloured screw caps.

2. Reagent sets are to be stored in the cool at +6 °C to +10 °C.

Chlorine L / M101

ENMethod Reference Book1.020

Determination of free chlorine with liquid reagent

Select the method on the device.

10 mL

Sample

Fill 24 mm vial with 10 mL

sample.

Close vial(s). Place sample vial in the

sample chamber. Pay

attention to the positioning.

Zero

Press the ZERO button. Remove the vial from the

sample chamber.

Empty vial.

Sample

Hold cuvettes vertically

and add equal drops by

pressing slowly.

Add 6 drops DPD 1 Buffer

Solution to the sample

vial.

Add 2 drops DPD

1 Reagent Solution to the

sample vial.

Chlorine L / M101

ENMethod Reference Book1.0 21

Fill up vial with sample to

the 10 mL mark.

Close vial(s). Invert several times to mix

the contents.

Sample

Test

Place sample vial in the

sample chamber. Pay

attention to the positioning.

Press the TEST (XD:

START)button.

The result in mg/L free chlorine appears on the display.

Determination of totale Chlorine with liquid reagent

Select the method on the device.

10 mL

Sample

Fill 24 mm vial with 10 mL

sample.

Close vial(s). Place sample vial in the

sample chamber. Pay

attention to the positioning.

Chlorine L / M101

ENMethod Reference Book1.022

Zero

Press the ZERO button. Remove the vial from the

sample chamber.

Empty vial.

Sample

Hold cuvettes vertically

and add equal drops by

pressing slowly.

Add 6 drops DPD

1 Buffer Solution to the

sample vial.

Add 2 drops DPD

1 Reagent Solution to the

sample vial.

Sample

Add 3 drops DPD

3 Solution to the sample

vial.

Fill up vial with sample to

the 10 mL mark.

Close vial(s).

Chlorine L / M101

ENMethod Reference Book1.0 23

Sample

Test

Invert several times to mix

the contents.

Place sample vial in the

sample chamber. Pay

attention to the positioning.

Press the TEST (XD:

START)button.

11 12

2 min

Wait for 2 minute(s)

reaction time.

Once the reaction period is finished, the measurement takes place automatically.

The result in mg/L total Chlorine appears on the display.

Chlorine L / M101

ENMethod Reference Book1.024

Chemical Method

DPD

Appendix

Interferences

Persistant Interferences

• All oxidising agents in the samples react like chlorine, which leads to higher results.

Removeable Interferences

• Interference from Copper and Iron (III) are eliminated by the addition of EDTA.

• Concentrations above 4 mg/L Chlorine, in the event of using fluid reagents, can lead

to results within the measuring range of up to 0 mg/L. In this case, the sample must be

diluted with chlorine-free water. 10 ml of the diluted sample should be mixed with the

reagent and the measurement taken again (plausibility test).

Interference from / [mg/L]

CrO4 2- 0,01

MnO20,01

Conformity

EN ISO 7393-2

a) determination of free, combined and total

Chlorine HR T / M103

ENMethod Reference Book1.026

Chlorine HR T M103

0.1 - 10 mg/L Cl2 a) CL10

DPD

Material

Required material (partly optional):

Reagents Packaging Unit Part Number

DPD No. 1 HR Tablet / 100 511500BT

DPD No. 1 HR Tablet / 250 511501BT

DPD No. 1 HR Tablet / 500 511502BT

DPD No. 3 HR Tablet / 100 511590BT

DPD No. 3 HR Tablet / 250 511591BT

DPD No. 3 HR Tablet / 500 511592BT

Set DPD No. 1 HR/No. 3 HR 100 Pc. #100 each 517791BT

Set DPD No. 1 HR/No. 3 HR 250 Pc. #250 each 517792BT

DPD No. 1 High Calcium e) Tablet / 100 515740BT

DPD No. 1 High Calcium e) Tablet / 250 515741BT

DPD No. 1 High Calcium e) Tablet / 500 515742BT

DPD No. 3 High Calcium e) Tablet / 100 515730BT

DPD No. 3 High Calcium e) Tablet / 250 515731BT

DPD No. 3 High Calcium e) Tablet / 500 515732BT

DPD No.3 HR Evo Tablet / 100 511920BT

DPD No. 3 HREvo Tablet / 250 511921BT

DPD No. 3 HREvo Tablet / 500 511922BT

Sampling

1. When preparing the sample, chlorine outgassing, e.g. through the pipette or

shaking, must be avoided.

2. The analysis must take place immediately after taking the sample.

Chlorine HR T / M103

ENMethod Reference Book1.0 27

Preparation

1. Cleaning of vials:

As many household cleaners (e.g. dishwasher detergent) contain reducing

substances, this can lead to lower results with the determination of chlorine.

To avoid measurement errors, the glassware used should be free of chlorine

consumption. To achieve this, all glassware should be placed in a sodium

hypochlorite solution (0.1 g/L) for one hour and then rinsed thoroughly with

deionised water.

2. For individual testing of free and total chlorine, the use of different sets of

glassware is recommended (EN ISO 7393-2, 5.3)

3. The DPD colour development is carried out at a pH value of 6.2 to 6.5. The

reagents therefore contain a buffer for the pH adjustment. Strong alkaline or acidic

water samples must therefore be adjusted between pH 6 and pH 7 before the

analysis (use 0.5 mol/Lsulphuric acid or 1 mol/Lsodium hydroxide).

Remarks

1. Evotablets can be used as an alternative to the corresponding standard tablet (e.g.

DPD No.3 Evo instead of DPD No.3).

Chlorine HR T / M103

ENMethod Reference Book1.028

Determination of free chlorine HR with tablet

Select the method on the device.

10 mL

Sample

Fill 24 mm vial with 10 mL

sample.

Close vial(s). Place sample vial in the

sample chamber. Pay

attention to the positioning.

Zero

Press the ZERO button. Remove the vial from the

sample chamber.

Empty vial except for a few

drops.

24 mm

Add DPD No. 1 HR tablet. Crush tablet(s) by rotating

slightly.

Fill up vial with sample to the

10 mL mark.

Chlorine HR T / M103

ENMethod Reference Book1.0 29

Sample

Close vial(s). Dissolve tablet(s) by

inverting.

Place sample vial in the

sample chamber. Pay

attention to the positioning.

Test

Press the TEST (XD:

START)button.

The result in mg/L free chlorine appears on the display.

Determination of total Chlorine HR with tablet

Select the method on the device.

10 mL

Sample

Fill 24 mm vial with 10 mL

sample.

Close vial(s). Place sample vial in the

sample chamber. Pay

attention to the positioning.

Chlorine HR T / M103

ENMethod Reference Book1.030

Zero

Press the ZERO button. Remove the vial from the

sample chamber.

Empty vial except for a few

drops.

24 mm

Add DPD No. 1 HR tablet. Add DPD No. 3 HR tablet. Crush tablet(s) by rotating

slightly.

Fill up vial with sample to

the 10 mL mark.

Close vial(s). Dissolve tablet(s) by

inverting.

Chlorine HR T / M103

ENMethod Reference Book1.0 31

Sample

Test

11 12

2 min

Place sample vial in the

sample chamber. Pay

attention to the positioning.

Press the TEST (XD:

START)button.

Wait for 2 minute(s)

reaction time.

Once the reaction period is finished, the measurement takes place automatically.

The result in mg/L total Chlorine appears on the display.

Chlorine HR T / M103

ENMethod Reference Book1.032

Chemical Method

DPD

Appendix

Interferences

Persistant Interferences

• All oxidising agents in the samples react like chlorine, which leads to higher results.

Removeable Interferences

• Interference from Copper and Iron (III) are eliminated by the addition of EDTA.

• The use of reagent tablets in samples with high Calcium content* and/or

high conductivity* can lead to turbidity of the sample and therefore incorrect

measurements. In this case, the alternative reagent tablet DPD No. 1 High Calcium

and reagent tablet DPD No. 3 High Calcium should be used.

*it is not possible to give exact values, because the development of turbidity depends

on the composition and nature of the sample.

Conformity

EN ISO 7393-2

a) determination of free, combined and total | e) alternative reagent, used instead of DPD No.1/No.3 in case of turbidity

in the water sample caused by high concentration of calcium and/or high conductivity | # including stirring rod, 10 cm

Copper T / M150

ENMethod Reference Book1.034

Copper T M150

0.05 - 5 mg/L Cua) Cu

Biquinoline

Material

Required material (partly optional):

Reagents Packaging Unit Part Number

Copper No. 1 Tablet / 100 513550BT

Copper No. 1 Tablet / 250 513551BT

Copper No. 2 Tablet / 100 513560BT

Copper No. 2 Tablet / 250 513561BT

Set Copper No. 1/No. 2 100 Pc.#100 each 517691BT

Set Copper No. 1/No. 2 250 Pc.#250 each 517692BT

Preparation

1. Strong alkaline or acidic water samples must be adjusted to pH 4 to 6 before

analysis.

Copper T / M150

ENMethod Reference Book1.0 35

Determination of Copper, free with tablet

Select the method on the device.

In addition, choose the test: free

10 mL

Sample

Fill 24 mm vial with 10 mL

sample.

Close vial(s). Place sample vial in the

sample chamber. Pay

attention to the positioning.

Zero

Press the ZERO button. Remove the vial from the

sample chamber.

24 mm

Add COPPER No. 1 tablet

Crush tablet(s) by rotating

slightly.

Close vial(s).

Copper T / M150

ENMethod Reference Book1.036

Sample

Test

Dissolve tablet(s) by

inverting.

Place sample vial in the

sample chamber. Pay

attention to the positioning.

Press the TEST (XD:

START)button.

11 12

2 min

Wait for 2 minute(s)

reaction time.

Once the reaction period is finished, the measurement takes place automatically.

The result in mg/L free Copper appears on the display.

Determination of Copper, total with tablet

Select the method on the device.

In addition, choose the test: total

10 mL

Sample

Fill 24 mm vial with 10 mL

sample.

Close vial(s). Place sample vial in the

sample chamber. Pay

attention to the positioning.

Copper T / M150

ENMethod Reference Book1.0 37

Zero

Press the ZERO button. Remove the vial from the

sample chamber.

24 mm

Add COPPER No. 1 tablet

Crush tablet(s) by rotating

slightly and dissolve.

Add COPPER No. 2 tablet .

24 mm

Crush tablet(s) by rotating

slightly.

Close vial(s). Dissolve tablet(s) by

inverting.

Copper T / M150

ENMethod Reference Book1.038

Sample

Test

11 12

2 min

Place sample vial in the

sample chamber. Pay

attention to the positioning.

Press the TEST (XD:

START)button.

Wait for 2 minute(s)

reaction time.

Once the reaction period is finished, the measurement takes place automatically.

The result in mg/L total Copper appears on the display.

Copper T / M150

ENMethod Reference Book1.0 39

Chemical Method

Biquinoline

Appendix

Interferences

Persistant Interferences

1. Cyanide CN- and Silver Ag+ interfere with the test result.

Method Validation

Limit of Detection 0.05 mg/L

Limit of Quantification 0.15 mg/L

End of Measuring Range 5 mg/L

Sensitivity 3.8 mg/L / Abs

Confidence Intervall 0.026 mg/L

Standard Deviation 0.011 mg/L

Variation Coefficient 0.42 %

Bibliography

Photometrische Analyse, Lange/Vedjelek, Verlag Chemie 1980

a) determination of free, combined and total | # including stirring rod, 10 cm

CyA T / M160

ENMethod Reference Book1.040

CyA T M160

10 - 160 mg/L CyA CyA

Melamine

Material

Required material (partly optional):

Reagents Packaging Unit Part Number

CyA-Test Tablet / 100 511370BT

CyA-Test Tablet / 250 511371BT

Deionised Water 250 mL 457022

Remarks

1. Cyanuric acid causes an extremely fine distributed turbidity with a milky appearance.

Individual particles are not attributable to the presence of cyanuric acid.

CyA T / M160

ENMethod Reference Book1.0 41

Determination of Cyanuric Acid Test with Tablet

Select the method on the device.

24 mm

5 mL

24 mm

5 mL

Fill 24 mm vial with 5 mL

deionised water .

Put 5 mL sample in the

vial.

Close vial(s).

Sample

Zero

Place sample vial in the

sample chamber. Pay

attention to the positioning.

Press the ZERO button. Remove the vial from the

sample chamber.

24 mm

Add CyA-Test tablet. Crush tablet(s) by rotating

slightly.

Close vial(s).

CyA T / M160

ENMethod Reference Book1.042

Sample

Test

Invert several times to

mix the contents (for at

least 60 s until the tablet is

completely dissolved).

Place sample vial in the

sample chamber. Pay

attention to the positioning.

Press the TEST (XD:

START)button.

The result in mg/L Cyanuric Acid appears on the display.

CyA T / M160

ENMethod Reference Book1.0 43

Chemical Method

Melamine

Interferences

Persistant Interferences

1. Undissolved particles may lead to higher results. Therefore, it is important to

dissolve the Tablet completely.

Iron T / M220

ENMethod Reference Book1.044

Iron T M220

0.02 - 1 mg/L Fe FE

Ferrozine / Thioglycolate

Material

Required material (partly optional):

Reagents Packaging Unit Part Number

Iron II LR (Fe2+) Tablet / 100 515420BT

Iron II LR (Fe2+) Tablet / 250 515421BT

Iron LR (Fe2+ und Fe3+) Tablet / 100 515370BT

Iron LR (Fe2+ und Fe3+) Tablet / 250 515371BT

Preparation

1. Water that has been treated with organic compounds such as corrosion inhibitors,

must be oxidised where necessary to break down the iron complex. 1 ml of

concentrated Sulphuric acid(≥ 95 %) and 1 ml concentrated Nitric acid(≥ 65 %) is

therefore added to to 100 ml water sample and boiled down to approximately half

the volume. After cooling down, the digestion procedure is continued.

Remarks

1. This method is for the determination of total dissolved Fe2+ and Fe3+.

2. For the determination of Fe2+, the IRON (II) LR Tablet, instead of the IRON LR

Tablet is used.

Iron T / M220

ENMethod Reference Book1.0 45

Digestion

100 mL 1 mL

11 12

10 min

Fill a suitable sample

vessel with 100 mL

sample .

Add 1 mL concentrated

sulfuric acid (≥ 95 %) .

The sample is to be heated

for 10 minutes, or for

as long as it takes for

everything to be completely

dissolved.

25 ºC

15 ºC

100 mL

Allow the sample to cool to

room temperature.

Adjust pH-value of the

sample with ammonia

solution (10-25 %) to 3-5.

Fill the sample with

deionised water to 100 mL

This sample is used for the analysis of total solved and dissolved Iron.

Determination of Iron (II,III), dissolved with Tablet

Select the method on the device.

For testing of dissolved and undissolved Iron, carry out the described digestion.

10 mL

Sample

Fill 24 mm vial with 10 mL

sample.

Close vial(s). Place sample vial in the

sample chamber. Pay

attention to the positioning.

Iron T / M220

ENMethod Reference Book1.046

Zero

Press the ZERO button. Remove the vial from the

sample chamber.

24 mm

Add IRON LR tablet. Crush tablet(s) by rotating

slightly.

Close vial(s).

Sample

Test

Dissolve tablet(s) by

inverting.

Place sample vial in the

sample chamber. Pay

attention to the positioning.

Press the TEST (XD:

START)button.

Iron T / M220

ENMethod Reference Book1.0 47

11 12

5 min

Wait for 5 minute(s)

reaction time.

Once the reaction period is finished, the measurement takes place automatically.

The result in mg/L Iron appears on the display.

Iron T / M220

ENMethod Reference Book1.048

Chemical Method

Ferrozine / Thioglycolate

Appendix

Interferences

Removeable Interferences

1. The presence of copper increases the test result by 10 %. At a concentration of 10

mg/L copper in the sample, the measurement result is increased by 1 mg/L iron.

The interference can be eliminated by the addition of thiourea

Method Validation

Limit of Detection 0.01 mg/L

Limit of Quantification 0.016 mg/L

End of Measuring Range 1 mg/L

Sensitivity 0.92 mg/L / Abs

Confidence Intervall 0.013 mg/L

Standard Deviation 0.005 mg/L

Variation Coefficient 1.23 %

Bibliography

Photometrische Analyse, Lange/ Vjedelek, Verlag Chemie 1980, p. 102

pH-value T / M330

ENMethod Reference Book1.050

pH-value T M330

6.5 - 8.4 pH PH

Phenol Red

Material

Required material (partly optional):

Reagents Packaging Unit Part Number

Phenol Red Photometer Tablet / 100 511770BT

Phenol Red Photometer Tablet / 250 511771BT

Phenol Red Photometer Tablet / 500 511772BT

Remarks

1. For photometric determination of pH values only use PHENOL RED tablets in black

printed foil pack and marked with PHOTOMETER.

pH-value T / M330

ENMethod Reference Book1.0 51

Determination of pH-value with Tablet

Select the method on the device.

10 mL

Sample

Fill 24 mm vial with 10 mL

sample.

Close vial(s). Place sample vial in the

sample chamber. Pay

attention to the positioning.

Zero

Press the ZERO button. Remove the vial from the

sample chamber.

24 mm

Add PHENOL RED

PHOTOMETER tablet.

Crush tablet(s) by rotating

slightly.

Close vial(s).

pH-value T / M330

ENMethod Reference Book1.052

Sample

Test

Dissolve tablet(s) by

inverting.

Place sample vial in the

sample chamber. Pay

attention to the positioning.

Press the TEST (XD:

START)button.

The result in pH value appears on the display.

pH-value T / M330

ENMethod Reference Book1.0 53

Chemical Method

Phenol Red

Appendix

Interferences

Persistant Interferences

1. Water samples with little Carbonate hardness* can lead to false pH values.

*KS4.3 < 0.7 mmol/l ≙ total alkalinity < 35 mg/L CaCO3.

Removeable Interferences

1. pH values below 6.5 and above 8.4 can produce results inside the measuring

range. A plausibility test (pH-meter) is recommended.

2. Salt error

For salt concentrations below 2 g/L, no significant error, is expected due to

the salt concentration of the reagent tablet. For higher salt concentrations the

measurement values

have to be adjusted as follows:

Salt

content

per

sample

in g/L

(seawater)

60 120 180

Correction -0.151) -0.212) -0.262) -0.292)

1) according to Kolthoff (1922)

2) according to Parson and Douglas (1926)

Bibliography

Colorimetric Chemical Analytical Methods, 9th Edition, London

pH value L / M331

ENMethod Reference Book1.054

pH value L M331

6.5 - 8.4 pH PH

Phenol Red

Material

Required material (partly optional):

Reagents Packaging Unit Part Number

Phenol Red Solution 15 mL 471040

Phenol Red Solution 100 mL 471041

Phenol Red Solution in 6-pack 1 Pieces 471046

Preparation

1. Due to differing drop sizes results can show a discrepancy in accuracy by

comparison with tablets.

This can be minimised by using a pipette (0.18 ml equivalent to 6 drops).

Remarks

1. After use, ensure the cuvette is once again closed with the same-coloured screw

caps.

2. Reagents are to be stored in the cool at +6 °C to +10 °C.

pH value L / M331

ENMethod Reference Book1.0 55

Determination of pH-value with liquidreagent

Select the method on the device.

10 mL

Sample

Fill 24 mm vial with 10 mL

sample.

Close vial(s). Place sample vial in the

sample chamber. Pay

attention to the positioning.

Zero

Press the ZERO button. Remove the vial from the

sample chamber.

Sample

Hold cuvettes vertically

and add equal drops by

pressing slowly.

Add 6 drops PHENOL

Red-Lösung to the

sample vial.

Close vial(s).

pH value L / M331

ENMethod Reference Book1.056

Sample

Test

Invert several times to mix

the contents.

Place sample vial in the

sample chamber. Pay

attention to the positioning.

Press the TEST (XD:

START)button.

The result in pH value appears on the display.

pH value L / M331

ENMethod Reference Book1.0 57

Chemical Method

Phenol Red

Appendix

Interferences

Removeable Interferences

1. Salt error Correction of test results (average values) for samples with salt contents

of:

2. Salt content of the sample Correction

30 g/L (seawater) -0.15 1)

60 g/L -0.21 2)

120 g/L -0.26 2)

180 g/L -0.29 2)

1) according to Kolthoff (1922) 2) according to Parson and

Douglas (1926)

3. When testing chlorinated water the residual chlorine contents can influence the

colour reaction of the liquid reagent. This can be avoided by adding a small crystal

of Sodiumthiosulphate (Na2S2O3⋅5 H2O) to the sample solution before adding the

PHENOL RED solution.

Bibliography

Colorimetric Chemical Analytical Methods, 9th Edition, London

DE Methodenhandbuch 01/20

KS4.3 T

0,1 - 4 mmol/l KS4.3

Säure / Indikator

S:4.3

Instrumentspezifische Informationen

Der Test kann auf den folgenden Geräten durchgeführt werden. Zusätzlich sind die

benötigte Küvette und der Absorptionsbereich der Photometer angegeben.

Geräte Küvette λMessbereich

MD 200, MD 600, MD 610,

MD 640, MultiDirect, PM 620,

PM 630

ø 24 mm 610 nm 0,1 - 4 mmol/l KS4.3

SpectroDirect, XD 7000,

XD 7500

ø 24 mm 615 nm 0,1 - 4 mmol/l KS4.3

Material

Benötigtes Material (zum Teil optional):

Reagenzien Form/Menge Bestell-Nr.

Alka-M-Photometer Tablette / 100 513210BT

Alka-M-Photometer Tablette / 250 513211BT

Anwendungsbereich

• Abwasserbehandlung

• Trinkwasseraufbereitung

• Rohwasserbehandlung

Anmerkungen

1. Die Begrie Alkalität-m, m-Wert, Gesamtalkalität und Säurekapazität KS4.3 sind

identisch.

2. Die exakte Einhaltung des Probevolumens von 10 ml ist für die Genauigkeit des

Analysenergebnisses entscheidend.

Displayanzeige

im MD 100 MD 110

/ MD 200

Barcode zur

Methodenerkennung

Methoden Name

Messbereich

Chemische

Methode

Methodennummer

Sprachkürzel nach

ISO 639-1 Revisionsstand

KS4.3 T / 20

Leitfaden für den Anwender

ENMethod Reference Book58

Durchführung der Bestimmung Säurekapazität KS4.3 mit Tablette

Die Methode im Gerät auswählen.

Für diese Methode muss bei folgenden Geräten keine ZERO-Messung durchgeführt

werden: XD 7000, XD 7500

10 ml

24-mm-Küvette mit 10 ml

Probe füllen.

Küvette(n) verschließen.

Sample

Die Probenküvette in

den Messschacht stellen.

Positionierung beachten.

Tablette(n) durch Um-

schwenken lösen.

Sample

Die Probenküvette in

den Messschacht stellen.

Positionierung beachten.

Test

Taste TEST (XD: START)

drücken.

In der Anzeige erscheint das Ergebnis als Säurekapazität KS4.3.

Durchführung der

Messung

KS4.3 T / 20

DE Methodenhandbuch 01/20

Leitfaden für den Anwender

ENMethod Reference Book 59

Alkalität-m T / M30

DEMethod Reference Book1.060

Alkalität-m T M30

5 - 200 mg/L CaCO3tA

Säure / Indikator

Material

Benötigtes Material (zum Teil optional):

Reagenzien Form/Menge Bestell-Nr.

Alka-M-Photometer Tablette / 100 513210BT

Alka-M-Photometer Tablette / 250 513211BT

Anmerkungen

1. Die Begriffe Alkalität-m, m-Wert, Gesamtalkalität und Säurekapazität KS4.3 sind

identisch.

2. Die exakte Einhaltung des Probevolumens von 10 ml ist für die Genauigkeit des

Analysenergebnisses entscheidend.

Alkalität-m T / M30

DEMethod Reference Book1.0 61

Durchführung der Bestimmung Alkalität, total= Alkaltät-m= m-

Wert mit Tablette

Die Methode im Gerät auswählen.

10 mL

Sample

24-mm-Küvette mit 10 mL

Probe füllen.

Küvette(n) verschließen. Die Probenküvette in

den Messschacht stellen.

Positionierung beachten.

Zero

Taste ZERO drücken. Küvette aus dem

Messschacht nehmen.

24 mm

Eine ALKA-M-

PHOTOMETER Tablette

zugeben.

Tablette(n) unter leichter

Drehung zerdrücken.

Küvette(n) verschließen.

Alkalität-m T / M30

DEMethod Reference Book1.062

Sample

Test

Tablette(n) durch

Umschwenken lösen.

Die Probenküvette in

den Messschacht stellen.

Positionierung beachten.

Taste TEST (XD: START)

drücken.

In der Anzeige erscheint das Ergebnis als Alkalität-m.

Alkalität-m T / M30

DEMethod Reference Book1.0 63

Auswertung

Die folgende Tabelle gibt an wie die ausgegebenen Werte in andere Zitierformen

umgewandelt werden können.

Einheit Zitierform Umrechnungsfaktor

mg/l CaCO31

°dH 0.056

°eH 0.07

°fH 0.1

°aH 0.058

KS4.3 0.02

Chemische Methode

Säure / Indikator

Appendix

Abgeleitet von

EN ISO 9963-1

Chlor T / M100

DEMethod Reference Book1.064

Chlor T M100

0,01 - 6,0 mg/L Cl2 a) CL6

DPD

Material

Benötigtes Material (zum Teil optional):

Reagenzien Form/Menge Bestell-Nr.

DPD No.1 Tablette / 100 511050BT

DPD No. 1 Tablette / 250 511051BT

DPD No. 1 Tablette / 500 511052BT

DPD No. 3 Tablette / 100 511080BT

DPD No. 3 Tablette / 250 511081BT

DPD No. 3 Tablette / 500 511082BT

DPD No. 1 High Calcium e) Tablette / 100 515740BT

DPD No. 1 High Calcium e) Tablette / 250 515741BT

DPD No. 1 High Calcium e) Tablette / 500 515742BT

DPD No. 3 High Calcium e) Tablette / 100 515730BT

DPD No. 3 High Calcium e) Tablette / 250 515731BT

DPD No. 3 High Calcium e) Tablette / 500 515732BT

DPD No. 4 Tablette / 100 511220BT

DPD No. 4 Tablette / 250 511221BT

DPD No. 4 Tablette / 500 511222BT

DPD No. 3 Evo Tablette / 100 511420BT

DPD No. 3 Evo Tablette / 250 511421BT

DPD No. 3 Evo Tablette / 500 511422BT

DPD No.4 Evo Tablette / 100 511970BT

DPD No. 4 Evo Tablette / 250 511971BT

DPD No. 4 Evo Tablette / 500 511972BT

Verfügbare Standards

Titel Verpackungseinheit Bestell-Nr.

ValidCheck Chlor 1,5 mg/L 1 St. 48105510

Chlor T / M100

DEMethod Reference Book1.0 65

Probenahme

1. Bei der Probenvorbereitung muss das Ausgasen von Chlor, z.B. durch Pipettieren

und Schütteln, vermieden werden.

2. Die Analyse muss unmittelbar nach der Probenahme erfolgen.

Vorbereitung

1. Reinigung der Küvetten:

Da viele Haushaltsreiniger (z.B. Geschirrspülmittel) reduzierende Stoffe enthalten,

kann es bei der Bestimmung von Chlor zu Minderbefunden kommen. Um diesen

Messfehler auszuschließen, sollten die Glasgeräte chlorzehrungsfrei sein. Dazu

werden die Glasgeräte für eine Stunde unter Natriumhypochloritlösung (0,1 g/L)

aufbewahrt und danach gründlich mit VE-Wasser (Vollentsalztes Wasser) gespült.

2. Für die Einzelbestimmung von freiem Chlor und Gesamtchlor ist es sinnvoll, jeweils

einen eigenen Satz Küvetten zu verwenden (siehe EN ISO 7393-2, Abs. 5.3).

3. Die DPD-Farbentwicklung erfolgt bei einem pH-Wert von 6,2 bis 6,5. Die

Reagenzien enthalten daher einen Puffer zur pH-Wert Einstellung. Stark alkalische

oder saure Wässer müssen jedoch vor der Analyse in einen pH-Bereich zwischen

6 und 7 gebracht werden (mit 0,5 mol/LSchwefelsäure bzw. 1 mol/LNatronlauge).

Anmerkungen

1. Evo-Tabletten können alternativ zu der entsprechenden Standard-Tablette

verwendet werden (z.B. DPD Nr. 3 Evo anstatt DPD Nr. 3).

Chlor T / M100

DEMethod Reference Book1.066

Durchführung der Bestimmung freies Chlor mit Tablette

Die Methode im Gerät auswählen.

10 mL

Sample

24-mm-Küvette mit 10 mL

Probe füllen.

Küvette(n) verschließen. Die Probenküvette in

den Messschacht stellen.

Positionierung beachten.

Zero

Taste ZERO drücken. Küvette aus dem

Messschacht nehmen.

Die Küvette bis auf einige

Tropfen entleeren.

24 mm

Eine DPD No. 1 Tablette

zugeben.

Tablette(n) unter leichter

Drehung zerdrücken.

Küvette bis zur 10-mL-Marke

mit der Probe auffüllen.

Chlor T / M100

DEMethod Reference Book1.0 67

Sample

Küvette(n) verschließen. Tablette(n) durch

Umschwenken lösen.

Die Probenküvette in

den Messschacht stellen.

Positionierung beachten.

Test

Taste TEST (XD: START)

drücken.

In der Anzeige erscheint das Ergebnis in mg/L freies Chlor.

Durchführung der Bestimmung gesamt Chlor mit Tablette

Die Methode im Gerät auswählen.

10 mL

Sample

24-mm-Küvette mit 10 mL

Probe füllen.

Küvette(n) verschließen. Die Probenküvette in

den Messschacht stellen.

Positionierung beachten.

Chlor T / M100

DEMethod Reference Book1.068

Zero

Taste ZERO drücken. Küvette aus dem

Messschacht nehmen.

Die Küvette bis auf einige

Tropfen entleeren.

Eine DPD No. 1 Tablette

zugeben.

Eine DPD No. 3 Tablette

zugeben.

Alternativ zur DPD Nr.

1 und Nr. 3 Tablette kann

eine DPD Nr. 4 Tablette

zugegeben werden.

24 mm

Tablette(n) unter leichter

Drehung zerdrücken.

Küvette bis zur 10-mL-

Marke mit der Probe

auffüllen.

Küvette(n) verschließen.

Chlor T / M100

DEMethod Reference Book1.0 69

Sample

Test

Tablette(n) durch

Umschwenken lösen.

Die Probenküvette in

den Messschacht stellen.

Positionierung beachten.

Taste TEST (XD: START)

drücken.

11 12

2 min

2 Minute(n) Reaktionszeit

abwarten.

Nach Ablauf der Reaktionszeit erfolgt automatisch die Messung.

In der Anzeige erscheint das Ergebnis in mg/L Gesamtchlor.

Chlor T / M100

DEMethod Reference Book1.070

Chemische Methode

DPD

Appendix

Störungen

Permanente Störungen

• Alle in den Proben vorhandenen Oxidationsmittel reagieren wie Chlor, was zu

Mehrbefunden führt.

Ausschließbare Störungen

• Störungen durch Kupfer und Eisen(III) sind durch EDTA zu beseitigen.

• Bei Proben mit hohem Calciumgehalt* und/oder hoher Leitfähigkeit* kann es

bei der Verwendung der Reagenztabletten zu einer Eintrübung der Probe und

damit verbundener Fehlmessung kommen. In diesem Fall sind alternativ die

Reagenztablette DPD No. 1 High Calcium und die Reagenztablette DPD No. 3 High

Calcium zu verwenden.

*exakte Werte können nicht angegeben werden, da die Entstehung einer Trübung von

Art und Zusammensetzung des Probenwassers abhängt.

• Konzentrationen über 10 mg/L Chlor, bei Verwendung von Tabletten, können zu

Ergebnissen innerhalb des Messbereichs bis hin zu 0 mg/L führen. Bei einer zu hohen

Chlorkonzentration muss die Probe mit chlorfreiem Wasser verdünnt werden. 10

mLder verdünnten Probe werden mit Reagenz versetzt und die Messung wiederholt

(Plausibilitätstest).

Störung Stört ab / [mg/L]

CrO4 2- 0.01

MnO20.01

Methodenvalidierung

Nachweisgrenze 0.02 mg/L

Bestimmungsgrenze 0.06 mg/L

Messbereichsende 6 mg/L

Empfindlichkeit 2.05 mg/L / Abs

Vertrauensbereich 0.04 mg/L

Verfahrensstandardabweichung 0.019 mg/L

Verfahrensvariationskoeffizient 0.87 %

Konform

EN ISO 7393-2

Chlor T / M100

DEMethod Reference Book1.0 71

a) Bestimmung von frei, gebunden, gesamt möglich | e) Hilfsreagenz, alternativ zur DPD No. 1 / No. 3 bei Eintrübungen

der Probe durch hohen Calciumionengehalt und/oder hohe Leitfähigkeit

Chlor L / M101

DEMethod Reference Book1.072

Chlor L M101

0,02 - 4,0 mg/L Cl2 a) CL6

DPD

Material

Benötigtes Material (zum Teil optional):

Reagenzien Form/Menge Bestell-Nr.

DPD 1 Pufferlösung, blaue Flasche 15 mL 471010

DPD 1 Pufferlösung 100 mL 471011

DPD 1 Pufferlösung im 6-er Pack 1 St. 471016

DPD 1 Reagenzlösung, grüne Flasche 15 mL 471020

DPD 1 Reagenzlösung 100 mL 471021

DPD 1 Reagenzlösung im 6-er Pack 1 St. 471026

DPD 3 Lösung, rote Flasche 15 mL 471030

DPD 3 Lösung 100 mL 471031

DPD 3 Lösung im 6-er Pack 1 St. 471036

DPD Reagenzien Set 1 St. 471056

Verfügbare Standards

Titel Verpackungseinheit Bestell-Nr.

ValidCheck Chlor 1,5 mg/L 1 St. 48105510

Probenahme

1. Bei der Probenvorbereitung muss das Ausgasen von Chlor, z.B. durch Pipettieren

und Schütteln, vermieden werden.

2. Die Analyse muss unmittelbar nach der Probenahme erfolgen.

Chlor L / M101

DEMethod Reference Book1.0 73