Documenttranscriptie

DIGITAL MIXING ENGINE SATELLITE Owner’s Manual EN  Precautions for Using a Rack-mounted DME Satellite If several DME Satellite units (or a DME Satellite unit together with other devices) are installed in a poorly-ventilated rack, the heat generated by each unit may raise the temperature inside the rack, preventing the DME Satellite from performing as designed. When mounting DME Satellite units in a rack, please leave one rack space vacant for every two units. You can attach a ventilation panel to this space or leave it open to prevent excessive heat build-up. If the temperature inside the rack is expected to rise above 40 degrees Celsius or 104 degrees Fahrenheit (or if the ambient temperature outside the rack is expected to rise above 30 degrees Celsius or 86 Fahrenheit), install a fan kit in the top row of the rack. The fan must provide airflow of 1.6 m3/min or more and static pressure of 5 mmH2O or more. Vorsichtsmaßnahmen für den Einsatz eines im Rack montierten DME Satellite Wenn in einem schlecht belüfteten Rack mehrere DME SatelliteEinheiten (oder eine DME Satellite-Einheit zusammen mit anderen Geräten) untergebracht sind, kann die von den Geräten erzeugte Wärme die Temperatur im Rack erhöhen, was die vorgesehene Leistung des DME Satellite beeinträchtigt. Wenn Sie DME SatelliteEinheiten in einem Rack einbauen, lassen Sie bitte alle zwei Geräte einen Rack-Platz frei. Sie können an diesem Platz eine Lüftungsverkleidung anbringen oder ihn offen lassen, um die Entwicklung übermäßiger Hitze zu verhindern. FR Si vous craignez que la température à l’intérieur du rack ne dépasse 40 degrés Celsius ou 104 degrés Fahrenheit (ou que la température ambiante à l’extérieur du rack ne dépasse 30 degrés Celsius ou 86 degrés Fahrenheit), installez un kit de ventilation sur la rangée supérieure du rack. Le ventilateur doit fournir un flux d’air de 1,6 m3/min ou plus et une pression statique de 5 mmH2O ou plus. Precauciones para utilizar una DME Satellite de montaje en bastidor Si se instalan varias unidades DME Satellite (o una unidad DME Satellite con otros dispositivos) en un bastidor insuficientemente ventilado, el calor generado por cada unidad podría aumentar la temperatura en el interior del bastidor, impidiendo que la unidad DME Satellite funcione de la manera prevista. Cuando monte unidades DME Satellite en un bastidor, deje un espacio de bastidor libre por cada dos unidades. Puede instalar un panel de ventilación en este espacio, o bien dejarlo abierto para evitar la acumulación de un calor excesivo. DE Wenn zu erwarten ist, dass die Temperatur im Rack über 40 Grad Celsius oder 104 Grad Fahrenheit ansteigt (oder wenn die Umgebungstemperatur außerhalb des Racks über 30 Grad Celsius oder 86 Grad Fahrenheit ansteigt), installieren Sie eine Lüftereinheit im Rack. Der Lüfter muss einen Luftdurchsatz von mindestens 1,6 m3/Minute oder mehr haben und einen statischen Druck von 5 mmH2O erzeugen können. Précautions à prendre en cas d’utilisation d’un satellite DME monté en rack Si vous installez plusieurs satellites DME (ou un satellite DME et d’autres périphériques) dans un rack mal aéré, la chaleur générée par chaque unité risque d’augmenter la température à l’intérieur du rack et d’empêcher le satellite DME de fonctionner correctement. Lorsque vous montez des satellites DME en rack, laissez un espace libre équivalant à un rack entre deux unités. Vous pouvez recouvrir cet espace d’un panneau de ventilation ou le laisser ouvert pour éviter toute accumulation de chaleur excessive. EN ES Si se espera que la temperatura interior del bastidor supere los 40 grados Celsius (o que la temperatura ambiente fuera del bastidor supere los 30 grados Celsius), instale un kit de ventilación en la fila superior del bastidor. El ventilador debe proporcionar una corriente de aire de 1,6 m3/min o más y una presión de 5 mmH2O o más. Fan kit INPUT DME Satellite USB PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL DIGITAL MIXING ENGINE SATELLITE INPUT INPUT DME Satellite USB PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL DIGITAL MIXING ENGINE SATELLITE INPUT Ventilation panel INPUT DME Satellite USB PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL DIGITAL MIXING ENGINE SATELLITE INPUT INPUT DME Satellite USB PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL DIGITAL MIXING ENGINE SATELLITE INPUT U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation © 2007 Yamaha Corporation  Explanation of Graphical Symbols The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The above warning is located on the top of the unit. IMPORTANT SAFETY INSTRUCTIONS 1 2 3 4 5 6 7 8 9 10 Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11 12 13 14 Only use attachments/accessories specified by the manufacturer. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. Unplug this apparatus during lightning storms or when unused for long periods of time. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. (98-6500)  FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/ or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA. 3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference. Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to co-axial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America, Electronic Service Division, 6600 Orangethorpe Ave, Buena Park, CA90620 The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries. * This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE) Responsible Party : Yamaha Corporation of America Address : 6600 Orangethorpe Ave., Buena Park, Calif. 90620 Telephone : 714-522-9011 Type of Equipment : DIGITAL MIXING ENGINE SATELLITE Model Name : DME8i-C/DME8o-C/DME4io-C This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received including interference that may cause undesired operation. See user manual instructions if interference to radio reception is suspected. * This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B) ADVARSEL! Lithiumbatteri—Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandoren. VARNING Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren. Kassera använt batteri enligt fabrikantens instruktion. VAROITUS Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden mukaisesti. (lithium caution) (FCC DoC) NEDERLAND / THE NETHERLANDS • Dit apparaat bevat een lithium batterij voor geheugen back-up. • This apparatus contains a lithium battery for memory back-up. • Raadpleeg uw leverancier over de verwijdering van de batterij op het moment dat u het apparaat ann het einde van de levensduur afdankt of de volgende Yamaha Service Afdeiing: Yamaha Music Nederland Service Afdeiing Kanaalweg 18-G, 3526 KL UTRECHT Tel. 030-2828425 • For the removal of the battery at the moment of the disposal at the end of the service life please consult your retailer or Yamaha Service Center as follows: Yamaha Music Nederland Service Center Address : Kanaalweg 18-G, 3526 KL UTRECHT Tel : 030-2828425 • Gooi de batterij niet weg, maar lever hem in als KCA. • Do not throw away the battery. Instead, hand it in as small chemical waste. IMPORTANT NOTICE FOR THE UNITED KINGDOM Connecting the Plug and Cord WARNING: THIS APPARATUS MUST BE EARTHED IMPORTANT. The wires in this mains lead are coloured in accordance with the following code: GREEN-AND-YELLOW : EARTH BLUE : NEUTRAL BROWN : LIVE As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows: The wire which is coloured GREEN-and-YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol or colored GREEN or GREEN-andYELLOW. The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. (lithium disposal) • This applies only to products distributed by Yamaha-Kemble Music (U.K.) Ltd.(3 wires)  PRECAUTIONS PLEASE READ CAREFULLY BEFORE PROCEEDING * Please keep this manual in a safe place for future reference. WARNING Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following: Power supply/Power cord Water warning • Only use the voltage specified as correct for the device. The required voltage is printed on the name plate of the device. • Do not expose the device to rain, use it near water or in damp or wet conditions, or place containers on it containing liquids which might spill into any openings. • Use only the included power cord. If you intend to use the device in an area other than in the one you purchased, the included power cord may not be compatible. Please check with your Yamaha dealer. • Never insert or remove an electric plug with wet hands. If you notice any abnormality • Do not place the power cord near heat sources such as heaters or radiators, and do not excessively bend or otherwise damage the cord, place heavy objects on it, or place it in a position where anyone could walk on, trip over, or roll anything over it. • Be sure to connect to an appropriate outlet with a protective grounding connection. Improper grounding can result in electrical shock. • If the power cord or plug becomes frayed or damaged, or if there is a sudden loss of sound during use of the device, or if any unusual smells or smoke should appear to be caused by it, immediately turn off the power switch, disconnect the electric plug from the outlet, and have the device inspected by qualified Yamaha service personnel. • If this device should be dropped or damaged, immediately turn off the power switch, disconnect the electric plug from the outlet, and have the device inspected by qualified Yamaha service personnel. Do not open • Do not open the device or attempt to disassemble the internal parts or modify them in any way. The device contains no user-serviceable parts. If it should appear to be malfunctioning, discontinue use immediately and have it inspected by qualified Yamaha service personnel. CAUTION Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the device or other property. These precautions include, but are not limited to, the following: • Do not place the device in an unstable position where it might accidentally fall over. Power supply/Power cord • Remove the electric plug from the outlet when the device is not to be used for extended periods of time, or during electrical storms. • Do not use the device in the vicinity of a TV, radio, stereo equipment, mobile phone, or other electric devices. Doing so may result in noise, both in the device itself and in the TV or radio next to it. • When removing the electric plug from the device or an outlet, always hold the plug itself and not the cord. Pulling by the cord can damage it. Connections Location • Before moving the device, remove all connected cables. • When setting up the product, make sure that the AC outlet you are using is easily accessible. If some trouble or malfunction occurs, immediately turn off the power switch and disconnect the plug from the outlet. Even when the power switch is turned off, electricity is still flowing to the product at the minimum level. When you are not using the product for a long time, make sure to unplug the power cord from the wall AC outlet. • Avoid setting all equalizer controls and faders to their maximum. Depending on the condition of the connected devices, doing so may cause feedback and may damage the speakers. • Do not expose the device to excessive dust or vibrations, or extreme cold or heat (such as in direct sunlight, near a heater, or in a car during the day) to prevent the possibility of panel disfiguration or damage to the internal components. (5)-4 4 DME8i-C/DME8o-C/DME4io-C Owner’s Manual • Before connecting the device to other devices, turn off the power for all devices. Before turning the power on or off for all devices, set all volume levels to minimum. • Be sure to connect to a properly grounded power source. A ground screw is provided on the rear panel of this device for maximum safety and shock prevention. If the mains outlet is not grounded, be sure to connect the ground screw to a confirmed ground point before plugging the device into the mains. Improper grounding can result in electrical shock. Maintenance • Remove the power plug from the AC outlet when cleaning the device. 1/2  Handling caution Backup battery • Do not use the device for a long period of time at a high or uncomfortable volume level, since this can cause permanent hearing loss. If you experience any hearing loss or ringing in the ears, consult a physician. • Do not rest your weight on the device or place heavy objects on it, and avoid use excessive force on the buttons, switches or connectors. • This device has a built-in backup battery. When you unplug the power cord from the AC outlet, the current scene data is retained. However, the life of the backup battery is about five years. If the battery wears out, the current scene data will be lost. When the backup battery charge becomes low, the [ERROR] indicator on the front panel blinks. In this case, save the data to a computer immediately, then ask a Yamaha dealer to replace the backup battery. Do not turn the [POWER] switch on and off repeatedly and rapidly. Be sure to wait six seconds or more between turning the power to the unit off and then on. The rubber feet included in this package can be attached to the bottom of this device to prevent slippage when it is to be used on a slipper y surface. Yamaha cannot be held responsible for damage caused by improper use or modifications to the device, or data that is lost or destroyed. Always turn the power off when the device is not in use. The performance of components with moving contacts, such as switches, volume controls, and connectors, deteriorates over time. Consult qualifi ed Yamaha service personnel about replacing defective components. • • • • The illustrations in this owner’s manual are for instructional purposes, and may appear somewhat different from the actual equipment. CobraNet is a trademark of Cirrus Logic, Inc. Ethernet is a trademark of Xerox Corporation. All other trademarks are the property of their respective holders and are hereby acknowledged. (5)-4 2/2 DME8i-C/DME8o-C/DME4io-C Owner’s Manual 5  Foreword Contents Introduction to the DME Satellite Foreword .......................................... 7 Connecting to an External Device............. 29 Accessories (Please make sure the following items are included in the package.)................................................. Options........................................................................... About the Product Names............................................... About the Firmware Version ........................................... Preparation...................................................................... Remote Connection ([REMOTE] Connector).............. 29 7 7 7 7 7 Controls and Connectors Connecting the AC power cord........................................... 7 Turning the power on and off ............................................. 7 CobraNet Connection (CobraNet Connectors)............. 30 GPI Connection ([GPI] Connector).............................. 31 Other Functions.................................. 32 Precautions for Using a Rack-mounted DME Satellite .... 8 Initializing the DME Satellite........................................ 32 Introduction to the DME Satellite .............. 9 References ....................................... 33 Connecting to a Computer Differences between DME8i-C, DME8o-C, and DME4io-C ..................................................................... 9 DME Satellite Features ................................................... 9 Audio System Network ................................................. 10 Glossary for the DME Satellite...................................... 10 Signal Types.................................................................. 12 System Examples........................................................... 13 About DME Designer ................................................... 14 About CobraNet ........................................................... 15 Audio I/O Connection CobraNet in a nutshell...................................................... Bundle .............................................................................. Multicast and unicast bundles ........................................... Conductors and performers............................................... Cables and hubs for CobraNet network ............................ 15 15 16 17 17 Controls and Connectors ....................... 18 Connecting to an External Device Front Panel ................................................................... 18 Rear Panel ..................................................................... 20 Connecting to a Computer ..................... 22 Other Functions USB Connection........................................................... 22 Network Settings........................................................... 23 Setting the IP address ........................................................ 23 Master and slave setting..................................................... 23 Ethernet Connection ([NETWORK] Connector)......... 24 Audio I/O Connection ........................... 27 References 6 Controlling external head amplifiers from the DME Satellite .................................................................... 29 Controlling the DME Satellite from an external device...... 29 Digital Audio Connection (CobraNet Connectors)....... 27 Analog Audio Connection ([INPUT] & [OUTPUT] Connectors) ................................................................. 28 DME8i-C/DME8o-C/DME4io-C Owner’s Manual Options ......................................................................... 33 ICP1.................................................................................. 33 CP4SW, CP4SF, and CP1SF............................................. 33 Troubleshooting ............................................................ 34 Component ................................................................... 34 MIDI Data Format ....................................................... 35 1. MIDI functions on the DME8i-C, DME8o-C, and DME4io-C ....................................................................35 2. MIDI Data Flow ........................................................... 35 3. MIDI Setup................................................................... 35 4. MIDI Format ................................................................ 36 MIDI Implementation Chart ........................................ 38 Display Messages........................................................... 39 Error Messages................................................................... 39 Warning Messages ............................................................. 39 General Specifications ................................................... Electrical Characteristics ................................................ Input/Output Characteristics ........................................ [NETWORK] Connector (100Base-TX Ethernet, RJ-45) ...................................... Straight and Crossover Cable Wiring............................. Dimensions ................................................................... Index ............................................................................. 40 40 43 44 44 45 46  Foreword Thank you for choosing a Yamaha DME8i-C/DME8o-C/DME4io-C Digital Mixing Engine Satellite. In order to take full advantage of the features and performance provided by the DME8i-C/DME8o-C/DME4io-C, we urge you to read this owner’s manual thoroughly before connecting or using the unit. Keep this manual in a safe place for future reference. Control Panels • ICP1 Intelligent Control Panel • CP4SW Control Panel • CP4SF Control Panel • CP1SF Control Panel NOT E For more information on your Control Panel, refer to the owner’s manual that came with the Control Panel, as well as the DME Designer Owner’s Manual. Turning the power on and off CAUTION To prevent the initial power-on surge from generating a large noise spike or damaging your speaker system, turn the devices on in the following order: audio sources, mixer (such as M7CL or PM5D), DME Satellite, and finally power amplifiers. Reverse this order when turning power off. 1. Press the [POWER] switch to turn on the power to the DME Satellite. 2. Press the [POWER] switch again to turn off the power. About the Product Names In this manual, models DME8i-C, DME8o-C, and DME4io-C are all called “DME Satellite,” and models DME64N and DME24N and the DME Satellite are categorized as the DME series. NOTE The DME Satellite remembers scene settings when you turn off the power. When you turn on the power to the DME Satellite, it will start up with the same scene settings. You can use the “Last Mem. Resume” setting in DME Designer to set up the DME Satellite so that at the startup it will recall the scene selected before you turned off the power to the device. About the Firmware Version CAUTION Do NOT turn off the power to the DME Satellite while it is receiving data from DME Designer or while it is being manipulated from an external device. Otherwise, a malfunction may occur. References You can check the version number of the DME Satellite firmware by using the DME Designer application software. You can also download the latest firmware from the following Yamaha website. http://www.yamahaproaudio.com/ Controls and Connectors First plug the female-connector end of the AC cord into the [AC IN] socket on the rear panel of the DME Satellite, then plug the male plug into an appropriate AC mains outlet. Be sure to use the voltage specified for the device. Connecting to a Computer Options CAUTION Be sure to turn all devices OFF before connecting AC mains power. Audio I/O Connection • • • • • • DME8i-C/DME8o-C/DME4io-C Owner’s Manual (this document) DME Designer Installation Guide CD-ROM AC power cord Euroblock plug (16P) x 1 Euroblock plug (3P) x 8 Rubber feet x 4 Connecting the AC power cord Connecting to an External Device • Preparation Other Functions Accessories (Please make sure the following items are included in the package.) Introduction to the DME Satellite Foreword DME8i-C/DME8o-C/DME4io-C Owner’s Manual 7  Foreword Foreword Precautions for Using a Rack-mounted DME Satellite Introduction to the DME Satellite Controls and Connectors If you install the DME Satellite along with other DME Satellite units or other devices in a poorly ventilated rack, the ambient temperature inside the rack may rise, resulting in inefficient performance. Be sure to install the DME Satellite in a well-ventilated rack and make sure that the heat will be ventilated efficiently. If the temperature inside the rack is expected to rise above 40 degrees Celsius or 104 degrees Fahrenheit (or if the ambient temperature outside the rack is expected to rise above 30 degrees Celsius or 86 Fahrenheit), install a fan kit in the top row of the rack. The fan must provide airflow of 1.6m3/min or more and static pressure of 5mmH2O or more. Fan kit Connecting to a Computer INPUT DME Satellite DME Satellite USB PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL DIGITAL MIXING ENGINE SATELLITE INPUT INPUT USB PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL DIGITAL MIXING ENGINE SATELLITE INPUT Audio I/O Connection Connecting to an External Device Other Functions References 8 DME8i-C/DME8o-C/DME4io-C Owner’s Manual  Foreword Introduction to the DME Satellite Differences between DME8i-C, DME8o-C, and DME4io-C Introduction to the DME Satellite The differences between these three models are as follows: ■ DME8i-C This model features 8-channel analog inputs. ■ DME8o-C This model features 4-channel analog inputs and 4-channel analog outputs. DME Satellite Features In addition to basic mixing and matrix output functions, the DME Satellite includes a equalizers, compressors, delay, etc. – that can be patched together via DME Designer to configure just about any audio system you need. The CobraNet connectors on the device enable you to remotely control analog inputs and outputs by transferring digital audio signals via a network. The following steps summarize the process for setting up the DME Satellite for use: Connecting to a Computer ■ DME4io-C Controls and Connectors This model features 8-channel analog outputs. 2. Install USB-MIDI Driver and DME Designer. (Refer to the DME Designer Installation Guide for details.) 3. Set up the network from DME Designer (page 23). Audio I/O Connection 1. Connect your computer to the DME Satellite via USB (page 22). 4. Connect devices. 5. Create a configuration using DME Designer, then transfer it to the DME Satellite. References (Refer to the DME Designer Owner’s Manual for details.) Other Functions Connecting to an External Device • Network connection Ethernet connection (page 24) USB connection (page 22) • CobraNet connection (page 30) • Analog connection (page 28) • External device connection Remote connection (page 29) GPI connection (page 31) DME8i-C/DME8o-C/DME4io-C Owner’s Manual 9  Foreword Introduction to the DME Satellite Audio System Network Introduction to the DME Satellite Multiple DME series units that are interconnected in a network via Ethernet function as a single audio system. In a DME audio system, a group of the same models that can be operated in sync is called a “device group;” audio processing divisions that accommodate multiple device groups are called “zones;” and the entire area serviced by the acoustic system is called an “area.” Each device group always includes one DME series unit that functions as the “group master” and controls all other DME series units in the same device group. If a computer is connected to the network, you can use the computer to control an entire device group via the group master. Controls and Connectors Glossary for the DME Satellite This section explains terminology specific to the DME Satellite. Components and parameters Connecting to a Computer The individual audio processing modules (equalizers, compressors, etc.) are called “components.” External head amplifier control modules are also available as components. Changing the parameters of components enables control over the operation of the components. Configuration Audio I/O Connection A “configuration” is a complete set of components for constructing an audio system. Each configuration determines the audio function(s) of the corresponding DME Satellite unit. All parameter sets included with each component in a configuration are called “preset parameters.” One DME Satellite unit has a number of configurations, and a configuration has a number of preset parameters. User Defined buttons (User Defined parameters) Assigning parameters to be User Defined parameters enables you to control the device from the ICP1. Refer to the DME Designer Owner’s Manual for details. Connecting to an External Device Other Functions References 10 DME8i-C/DME8o-C/DME4io-C Owner’s Manual  Foreword Introduction to the DME Satellite Scene structure Scene Preset Parameter Configuration Matrix Mixer Scene 1 Ex.: Gate • Attack • Decay • Range • Threshold • Key in • Hold Scene 2 16 x 8 Scene 999 Component Controls and Connectors A combination of all configuration and preset parameters is called a “scene.” Scenes can be recalled from an ICP1, GPI device, other external controllers, or computer. Up to 999 scenes can be stored for each device group. Introduction to the DME Satellite Scene Dark Change Band Set Second Act Band Set Play Set Play Set Play Set Stage Band Set Stage Stage INPUT USB INPUT PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL DIGITAL MIXING ENGINE SATELLITE USB PEAK PEAK SIGNAL SIGNAL PEAK PEAK PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL SIGNAL SIGNAL INPUT DIGITAL MIXING ENGINE SATELLITE INPUT Connecting to an External Device Scene 2 Other Functions Scene Recall References Scene 1 PEAK SIGNAL PEAK SIGNAL Audio I/O Connection First Act Connecting to a Computer Scene change DME8i-C/DME8o-C/DME4io-C Owner’s Manual 11  Foreword Introduction to the DME Satellite Signal Types DME Satellite audio system signals can be broadly categorized as follows. Introduction to the DME Satellite 1 Audio The DME Satellite will be required to send and receive audio signals to and from other DME series units as well as other audio equipment. Audio signal transmission and reception will occur primarily via the [INPUT] and [OUTPUT] connectors. The CobraNet connectors can also transmit and receive digital audio signals. 2 Device group control Controls and Connectors Connecting to a Computer Device group control signals control all DME series devices in the group. There are two types of device group control signals, as follows: • Control signals between the computer and the group master DME series unit • Control signals between the group master DME series unit and the other DME series units You can use the DME Designer application to control the entire device group, such as sending components to the devices and setting the parameters as required. 3 Device control These signals provide communication and control between individual devices. Included in this category are MIDI messages transferred between [USB] connectors, GPI signals transferred between [GPI] connectors, and remote head amp control signals handled via the [REMOTE] connector. Type of signals handled by the DME Satellite Audio I/O Connection Connector Connecting to an External Device Other Functions Device Group Control Device Control Reference Page — Control signals between the computer and the group master DME series unit Transmission/reception of control signals between computer and DME series units page 22 — • Control signals between the computer and the group master DME series unit • Control signals between the group master DME series unit and the other DME series units Transmission/reception of control signals between computer and DME series units page 24 Up to 16 channels of input and output. — Transmission/reception of MIDI messages page 27 page 30 — Input/output of GPI control signals between GPI device (GPI controller, etc.) and DME series unit page 31 — — • Transmission/reception of control signals to/ from an external device (such as AD8HR head amplifier) • Transmission/reception of MIDI messages page 29 The number of I/O channels depends on model. — — page 28 Audio Signal [USB] Connector [NETWORK] Connector CobraNet Connector [GPI] Connector — [REMOTE] Connector References 12 [INPUT]/[OUTPUT] Connectors (audio in/out) DME8i-C/DME8o-C/DME4io-C Owner’s Manual  Foreword Introduction to the DME Satellite System Examples Space B Space A DME8i-C Computer ICP1 INPUT USB PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL DIGITAL MIXING ENGINE SATELLITE INPUT Analog In DME8i-C Introduction to the DME Satellite Multiple DME Satellite units: Large-scale system INPUT USB PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL DIGITAL MIXING ENGINE SATELLITE INPUT Analog In DME8i-C INPUT USB PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL DIGITAL MIXING ENGINE SATELLITE INPUT Hub Hub Analog In DME8i-C Controls and Connectors Hub INPUT USB PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL DIGITAL MIXING ENGINE SATELLITE INPUT HOME UTILITY LEVEL MUTE CANCEL ENTER MY16-CII × 3 Space C DME8o-C Analog Out DME8o-C Analog Out DME8o-C Analog Out DME8o-C Analog Out Hub Hub Audio I/O Connection SCENE Connecting to a Computer Analog In DME64N Connecting to an External Device Hub DME8i-C Ethernet INPUT USB PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL DIGITAL MIXING ENGINE SATELLITE INPUT CobraNet Analog In Ethernet Switching Hub DME4io-C Analog Out Other Functions Space D Hub CobraNet Switching Hub DME8o-C Analog Out DME4io-C Analog Out Hub References Analog In Analog In DME8i-C/DME8o-C/DME4io-C Owner’s Manual 13  Foreword Introduction to the DME Satellite About DME Designer Introduction to the DME Satellite Controls and Connectors DME Designer software enables you to integrate, configure, and control the DME series system from a connected computer. You can build the DME series audio system using graphic blocks in DME Designer that are displayed on the computer monitor. The DME series settings, configuration, and parameter data are transferred from the computer to the DME series unit via the USB or Ethernet connection. Once the data is transferred to the unit, you can disconnect the DME series unit from the computer and use it as a stand-alone processor. Alternatively, you can control the DME series unit real-time from DME Designer as long as it is connected to a computer. If multiple DME series units are connected in the network, DME Designer enables you to build a configuration that includes those units. Refer to the “Connecting to a Computer” (page 22) for more information on connecting a computer to the DME Satellite. Refer to the DME Designer Installation Guide for detailed information on installing the DME Designer application and required software drivers. Refer to the DME Designer Owner’s Manual for setup and operation instructions. Connecting to a Computer Audio I/O Connection Connecting to an External Device Other Functions References 14 DME8i-C/DME8o-C/DME4io-C Owner’s Manual  Foreword Introduction to the DME Satellite About CobraNet Controls and Connectors Developed by Cirrus Logic, Inc., U.S., CobraNet technology allows real-time uncompressed digital audio distribution over industry-standard Fast Ethernet (100 megabits/sec.) networks. Up to 128 channels, 64 in each direction, can be carried simultaneously over a CobraNet network. (The number of channels available depends on the performance of the devices and the condition of audio signals.) CobraNet currently supports a 48 or 96 kHz sampling rate with 16, 20, or 24-bit resolution. It can also transfer control data along with audio signals. The type of control data that the network can handle depends on the type of devices on the network. When an audio signal passes through the CobraNet network, it causes a fixed latency of 5.33 milliseconds (or, depending on the setting, 2.67 or 1.33 milliseconds). Visit the CobraNet home page for more information on CobraNet. Introduction to the DME Satellite CobraNet in a nutshell The maximum number of channels that can be assigned to each bundle is as follows. Maximum channels per bundle Latency * ** 16bit, 48kHz 20bit, 48kHz 24bit, 48kHz 16bit, 96kHz 20bit, 96kHz 24bit, 96kHz 5.33ms 8 8 7 4* 4* 3** 2.66ms 8 8 8 4* 4* 4* 1.33ms 8 8 8 4* 4* 4* Since 96-kHz audio is handled as two 48-kHz signals combined, the maximum number of channels is halved. The audio signal output from the 4th channel will include some aliasing noise, and proper operation cannot be guaranteed. Please do not use this channel. NO T E Audio I/O Connection Connecting to an External Device CobraNet network transmits digital audio data in bundles. When bundles are received, they are converted back into the original digital audio data. With the DME Satellite, a single bundle can carry up to eight channels of digital audio. For routing around the network, bundles are assigned numbers from 1 through 65,279. If you set the same bundle number on both transmitting and receiving devices, digital audio data can be transmitted over CobraNet network. There is no limitation to the number of bundles that can be transmitted and received over the CobraNet network, as long as there are enough network resources. The number of bundles that can be handled depends on the device. The DME Satellite can use up to 4 output bundles and up to 8 input bundles. You can specify the bundle number by using the DME Designer application. Other Functions Bundle Connecting to a Computer CobraNet home page http://www.cobranet.info/ Number of bundles per channel and usable channels Channels per Bundle Bundle 1 Bundle 2 Bundle 3 Bundle 4 Bundle 5 Bundle 6 Bundle 7 Bundle 8 8 1-8 9-16 – – – – – – 4 1–4 5–8 9–12 13–16 – – – – 2 1–2 3–4 5–6 7–8 9–10 11–12 13–14 15–16 1 1 2 3 4 5 6 7 8 DME8i-C/DME8o-C/DME4io-C Owner’s Manual References The number of channels per bundled can be changes as shown below. Depending on the configuration, the maximum number of channels that can be handle may be less than 8. 15  Foreword Introduction to the DME Satellite Multicast and unicast bundles Introduction to the DME Satellite Controls and Connectors CobraNet bundles can be either multicast or unicast. Multicast bundles are transmitted from one device to multiple devices on the network (one-to-many). Unicast bundles are transmitted from one device to another (one-to-one). Unicast bundles are transmitted only when another device is configured to receive them by assigning the same bundle numbers. On the other hand, multicast bundles are transmitted to all devices on the network regardless of whether any devices are configured to receive them, and only devices that are configured to receive those bundles actually process them. It is recommended that no more than four multicast bundles (offering up to 32 channels) be used, since transmission of multicast bundles consumes more network resources. Unicast bundles should be used if five or more bundles are required. It is also possible to set multiple devices to receive the same unicast bundle number, and depending on the transmitting device up to 4 receiving devices may be able to simultaneously receive the same bundle. This situation is known as “multi-unicast.” The DME Satellite is capable of handling multi-unicast bundles. Multicast and unicast bundles are identified by bundle number. Multicast bundles are numbered 1 through 255. Unicast bundles are numbered 256 through 65,279. Connecting to a Computer Multicast bundle If Device A is transmitting multicast bundles, they will be transmitted to all devices on the CobraNet network (e.g., Devices B, C, and D in the example). Audio I/O Connection Connecting to an External Device Other Functions CobraNet Device A B Unicast bundle If Device A is transmitting unicast bundles, and the same bundle numbers are assigned to the transmitting bundles on Device A and receiving bundles on Device D, then Device A will transmit the unicast bundels to Device D. D CobraNet Device CobraNet Device CobraNet Device CobraNet Device A B Network C CobraNet Device DME8i-C/DME8o-C/DME4io-C Owner’s Manual Digital Audio Data Network C References 16 CobraNet Device D CobraNet Device Digital Audio Data  Foreword Introduction to the DME Satellite NO T E Controls and Connectors One device on the CobraNet network works as the conductor (network sync master). All other CobraNet devices are performers (network sync slaves). Each device synchronizes its own internal clock to the beat packets (sync signals) transmitted by the conductor. The conductor device is chosen automatically and no user intervention is required. However, setting an appropriate conductor priority could enable users to assign any device as the conductor. Refer to the DME Designer Owner’s Manual for more information on setting the conductor priority. If the DME Satellite is the conductor, the [IN USE/CONDUCTOR] LED flashes orange. If the conductor fails, another device automatically takes over. Since the conductor transmits beat packets (sync signals) onto the network, each performer does not require an external word clock connection, reducing cabling complexity and cost. Any non-networked digital audio equipment should derive its word clock from a CobraNet networked device. Introduction to the DME Satellite Conductors and performers References Other Functions Connecting to an External Device Category-5 metal cables can be used for runs of up to 100 meters. The maximum distance for multimode fiber optic cable is 2 kilometers. However, due to differences in cables, as well as switching hub and CobraNet device performance, proper operation at the maximum length cannot be guaranteed in all cases. Ethernet cables are categorized into crossover cables and straight cables. When you connect two devices directly together, use a crossover Ethernet cable. Use a switching hub and straight cables to connect three or more network devices. Audio I/O Connection Cables and hubs for CobraNet network Connecting to a Computer All CobraNet networked devices, regardless of whether each device serves as the conductor or a performer, can receive digital audio data and control data. DME8i-C/DME8o-C/DME4io-C Owner’s Manual 17  Foreword Controls and Connectors Front Panel Introduction to the DME Satellite 2 5 DME8i-C 7 9 INPUT USB PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL DIGITAL MIXING ENGINE SATELLITE INPUT 1 34 6 8 Controls and Connectors 2 5 DME8o-C USB Connecting to a Computer 1 34 6 7 PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL 9 DIGITAL MIXING ENGINE SATELLITE 8 2 5 7 9 DME4io-C INPUT USB Audio I/O Connection 1 Connecting to an External Device Other Functions 1 [USB] Connector Use this connector to connect the DME Satellite to the computer’s USB port. If you plan to use a USB connection, you must first install the USB-MIDI Driver on your computer. Refer to the DME Designer Installation Guide for installation instructions. Be sure to follow the procedure below when you make a USB connection with a computer. Otherwise, the computer and/ or DME Satellite may freeze, resulting in damages or loss of data. If the computer or DME Satellite freezes, turn the power to the DME Satellite off and then on, then restart the computer. CAUTION PEAK PEAK SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL DIGITAL MIXING ENGINE SATELLITE 8 • Before you connect the DME Satellite to the computer via USB, cancel the computer’s energy saving mode (such as Suspend, Sleep, or Stand-by mode). • Before turning on the power to the DME Satellite, first connect its [USB] connector to the computer’s USB port. • Before turning the power to the unit on or off, and before connecting or disconnecting the USB cable, take the following actions: - Quit all open applications. - Make sure that the DME Satellite is NOT transferring any data. • Be sure to wait six seconds or more between turning the power to the unit on and then off (or off and then on), or between connecting and disconnecting (or vice versa) the USB cable. 2 [NETWORK] Indicator Lights orange while data communication is occurring via the [USB] or [NETWORK] connector. References 18 34 6 PEAK SIGNAL 3 [MASTER] Indicator Lights green when the device is operating as the group master. The indicator is turned off if the device is operating as a slave. You can assign the group master in DME Designer. DME8i-C/DME8o-C/DME4io-C Owner’s Manual  Foreword Controls and Connectors Introduction to the DME Satellite 4 [ERROR] Indicator Lights when an error occurs. The [PEAK] indicators reflect the type of error. The [ERROR] indicator flashes when the battery charge is getting low. Controls and Connectors 5 [IN USE/CONDUCTOR] Indicator Lights orange when the power is supplied correctly to the DME Satellite. It flashes while the device is operating as a CobraNet conductor. If the secondary (backup) connector on the DME Satellite is connected (page 21), the indicator turns off every three seconds to indicate an abnormality on the primary connection. NOT E Refer to page 21 for information on the primary and secondary connectors. Connecting to a Computer 6 [LINK/ACTIVITY] Indicator Lights up steadily or flashes slowly when cables are connected correctly to the CobraNet connectors. It flashes rapidly while the unit is transferring data onto the network correctly. If the secondary (backup) connection is being used for communication, the indicator turns off every three seconds to indicate an abnormality on the primary connection. Audio I/O Connection 7 [PEAK] Indicators Light red when the signal level at the corresponding built-in analog audio inputs or outputs ([INPUT] or [OUTPUT] connectors) reaches or exceeds -3 dBFS. They also indicate an error number or status. Connecting to an External Device 8 [SIGNAL] Indicators Light green when the signal level at the corresponding builtin analog audio inputs or outputs ([INPUT] or [OUTPUT] connectors) reaches or exceeds -40 dBFS. They also indicate the status, for example, of the initialization process. NOT E Other Functions Remove the transparent protective film that was applied to the indicator panel prior to shipment from the factory. References 9 [POWER] Switch Turns mains power to the device on and off. The DME Satellite will start up with the same scene settings that were active when it shut down. You can use the “Last Mem. Resume” setting in DME Designer to set up the DME Satellite so that at startup it will recall the scene selected before you turned off the power to the device. DME8i-C/DME8o-C/DME4io-C Owner’s Manual 19  Foreword Controls and Connectors Rear Panel Introduction to the DME Satellite DME8i-C 1 3 4 5 6 7 9 MAC ADD * XX XX XX XX XX XX * RS-232C RS-422 8 2 Controls and Connectors DME8o-C 1 3 4 5 6 7 MAC ADD * XX XX XX XX XX XX * RS-232C RS-422 Connecting to a Computer 2 DME4io-C ) 8 1 3 4 5 6 7 9 MAC ADD * XX XX XX XX XX XX * RS-232C Audio I/O Connection RS-422 2 Connecting to an External Device 1 [AC IN] Connector Connect to the AC mains using the supplied AC power cord. First connect the power cord to the DME Satellite, then insert the power cord plug into an AC outlet. Other Functions 2 Ground Screw For maximum safety be sure to securely connect the DME Satellite ground screw to an earth connection. The supplied power cable has a three-prong plug that will ground the unit when the plug is inserted into an appropriately grounded three-prong type AC mains outlet. If the AC outlet is not grounded, be sure to ground the unit by using this ground screw. Correct grounding will effectively eliminate hum noise and interference. References 3 [NETWORK] Connector This is a 100Base-TX/10Base-T Ethernet connector for connection to a computer or to another DME series unit in the network. See “Ethernet Connection ([NETWORK] Connector)” on page 24 for connection details. NO T E Use a CAT5 STP (Shielded Twisted Pair) cable for this connection to prevent electromagnetic interference. 20 DME8i-C/DME8o-C/DME4io-C Owner’s Manual 8 ) 4 Dip Switch This 6-bit dip switch enables you to select the [REMOTE] connector function or initialize the DME Satellite, depending on its setting at the startup of the device. To switch between RS-232C and RS-422 for the [REMOTE] connector function, turn off the power to the device, set the dip switch as shown below, then turn on the power to the device again. See page 32 for the DME Satellite initialization procedure. RS-232C RS-422 RS-232C RS-232C RS-422 RS-422 If you do not plan to initialize the DME Satellite, CAUTION set all dip switch bits (excluding one bit for the RS-422 setting) in the upper position. 5 [REMOTE] Connector This 9-pin D-SUB connector allows connection to a Yamaha AD824 or AD8HR remote head amplifier or an RS232C/RS-422 compatible controller such as those from AMX or Crestron. See “Remote Connection ([REMOTE] Connector)” on page 29 for connection details.  Foreword Controls and Connectors Controls and Connectors Introduction to the DME Satellite 6 CobraNet [PRIMARY]/[SECONDARY] Connectors The DME Satellite features two CobraNet connectors for built-in redundancy: one for a primary network connection, another for a secondary or backup connection. If for some reason the primary connection fails (e.g., a cable is damaged, inadvertently disconnected, or a switching hub fails), the secondary connection automatically kicks in. Audio transmission is momentarily interrupted, but the duration of interruption varies depending on the hub performance or settings, and the system configuration. NOT E Connecting to a Computer • You can check the CobraNet connection status by looking at the [IN USE/CONDUCTOR] and [LINK ACTIVITY] indicators. The indicators on both sides to the CobraNet connectors are turned off. • Use a CAT5 STP (Shielded Twisted Pair) cable to prevent electromagnetic interference. 7 MAC Address This is the CobraNet’s MAC (Media Access Control) address. Audio I/O Connection 8 [GPI] Connector This Euroblock connector provides access to the unit’s GPI (General Purpose Interface) interface for transfer of control signals to and from external equipment. It features 8-port input and 4-port output. The +V terminals have an output voltage of 5 volts. The IN terminal detects voltage changes from 0V to 5V. The OUT terminals output either signal “L” or “H” at a TTL level. (See page 31.) Connecting to an External Device 9 [INPUT] Connectors These Euroblock connectors receive 8-channel analog audio signals on the DME8i-C. These Euroblock connectors receive 4-channel analog audio signals on the DME4io-C. References Other Functions ) [OUTPUT] Connectors These Euroblock connectors output 8-channel analog audio signals on the DME8o-C. These Euroblock connectors output 4-channel analog audio signals on the DME4io-C. DME8i-C/DME8o-C/DME4io-C Owner’s Manual 21  Foreword Connecting to a Computer USB Connection Introduction to the DME Satellite To connect multiple DME Satellite units to a network, you must assign appropriate IP addresses and make other network settings on all units. To achieve this, you need to connect the [USB] connector of one of the DME Satellite units to the USB port of the computer using USB cables, install USB-MIDI Driver and DME Designer on the computer, then assign the IP addresses to the DME Satellite units from DME Designer. N OT E Controls and Connectors • Refer to the separate DME Designer Installation Guide for details on installing USB-MIDI Driver and DME Designer. • Make sure that the USB-MIDI Driver’s THRU setting is “OFF.” • Refer to “Network Settings” on page 23 for more information on assigning IP addresses from DME Designer. Connecting to a Computer USB connections can be used in the following three ways: (1) Set up the network (e.g., assign a unique IP address to each DME Satellite) from DME Designer. (2) Control the group master DME Satellite from DME Designer. (3) Connect to any individual DME Satellite and control that DME Satellite unit by transmitting MIDI commands from a MIDI sequencer or similar software. N OT E • You can use DME Designer to control an entire device group through the group master. • The correspondence between the MIDI commands to be received/transmitted and the scene parameters can be set up using DME Designer. • The USB port being used by DME Designer is not available for use by a MIDI sequencer or other application. Audio I/O Connection USB Cable Device Group Group Master INPUT USB PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL DIGITAL MIXING ENGINE SATELLITE INPUT DME Satellite Connecting to an External Device Ethernet Cable Computer (Running DME Designer.) Switching Hub Ethernet Straight Cable Ethernet Cable Other Functions DME64N/24N INPUT USB PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL DIGITAL MIXING ENGINE SATELLITE INPUT DME Satellite SCENE HOME UTILITY LEVEL MUTE CANCEL ENTER USB Cable References 22 DME8i-C/DME8o-C/DME4io-C Owner’s Manual Computer (Running MIDI Sequencer or similar application.)  Foreword Connecting to a Computer Network Settings Setting the IP address Host Address Each group of digits between periods in an IP address is called an “octet.” These groups of digits are called “1st octet,” “2nd octet,” etc., starting from the left-most digit group. You cannot specify 0, 127, or 223 through 255 for the 1st octet of the network address. You can specify the following range of values for the 4th octet. Master : 2-253 Slave : 3-253 Connecting to a Computer Controls and Connectors Network Address Introduction to the DME Satellite Assign the IP address and master ID from DME Designer as shown below: Each device group must have one master. All other devices in the group are assigned as slave. If a particular DME Satellite unit is assigned as slave, you must set its master ID to the value of the 4th octet of the master DME Satellite IP address. NO T E References If you are using the DME Satellite along with a DME64N/24N, assign the DME Satellite as the master. This will optimize the network communication speed. Connecting to an External Device Master and slave setting Other Functions • Subnet mask is fixed at 255.255.255.0. • The host address is automatically set to 254. Gateway address is the same network address as the IP address. • Assign each of DME series units a unique IP address so that there are no duplicates. Assigning duplicate IP addresses may cause serious network problems. • You cannot make any network settings while using the DME Designer application on-line. To make network settings, first set DME Designer off-line. Refer to the DME Designer Owner’s Manual for details. • If you have connected a PM5D and a DME Satellite via CobraNet and are controlling the DME Satellite from the PM5D, you must specify a value of 2 as the fourth octet of the group master DME Satellite’s IP address. Audio I/O Connection NO T E DME8i-C/DME8o-C/DME4io-C Owner’s Manual 23  Foreword Connecting to a Computer Ethernet Connection ([NETWORK] Connector) To control the DME Satellite from the computer via Ethernet, use an Ethernet cable to connect the [NETWORK] connector on the rear panel of the DME Satellite to the computer, then install DME-N Network Driver. Introduction to the DME Satellite N OT E • Refer to the separate DME Designer Installation Guide for details on installing DME-N Network Driver. • Appropriate IP addresses must first be assigned to all devices connected to an Ethernet network. Connect your computer to one of the DME Satellite units via USB, then assign the IP addresses from DME Designer (page 22). Two DME Satellite units directly connected via Ethernet Controls and Connectors INPUT USB PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL DIGITAL MIXING ENGINE SATELLITE INPUT DME Satellite (IP address: 192.168.0.10 (Master ID: 2) Ethernet Cable Connecting to a Computer Group Master INPUT USB Audio I/O Connection Connecting to an External Device PEAK PEAK SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL DIGITAL MIXING ENGINE SATELLITE INPUT DME Satellite (IP address: 192.168.0.2) USB Cable You can connect devices in the same device group directly to each other using Ethernet cables, without connecting them to a switching hub. If they are DME Satellite units, you can use either crossover cables or straight cables. In this case, from DME Designer set Link Mode on both units to the same setting. Devices in different subnet (different network address) groups can be connected via a router or layer-3 compliant switching hub. HINT Since the DME Satellite supports Auto MDI/MDI-X, it will automatically detect whether the connected cable is of the straight type or crossover type, and will configure itself to create the optimal connection. Therefore, you can use either a straight or crossover cable. Other Functions References 24 PEAK SIGNAL DME8i-C/DME8o-C/DME4io-C Owner’s Manual  Foreword Connecting to a Computer Control from a computer in the same subnet group Device Group Introduction to the DME Satellite Group Master INPUT USB PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL DIGITAL MIXING ENGINE SATELLITE INPUT DME Satellite (IP address: 192.168.0.7) Ethernet Cable Ethernet Straight Cable Ethernet Straight Cable Computer (IP address: 192.168.0.100) INPUT USB PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL DIGITAL MIXING ENGINE SATELLITE INPUT DME Satellite (IP address: 192.168.0.3) (Master ID: 7) SCENE HOME UTILITY LEVEL MUTE CANCEL ENTER Connecting to a Computer DME64N/24N (IP address: 192.168.0.250) (Master ID: 7) NO T E • The IP addresses in the diagram are examples. • Use a switching hub that is compatible with 100Base-TX/10Base-T network speeds. The maximum length of a cable between a switching hub and the DME Satellite is 100 meters. Due to the quality of cables and switching hub performance, however, proper operation at the maximum length cannot be guaranteed in some cases. Use a CAT5 STP (Shielded Twisted Pair) cable to prevent electromagnetic interference. • If you are using multiple DME series units, set Link Mode on each unit to the same setting. Yamaha recommends that you select 100Base-TX for the Link Mode setting. Audio I/O Connection Ethernet Cable Controls and Connectors Switching Hub Device Group Port settings • Destination network address: 192.168.0.0 • Subnet mask: 255.255.255.0 • Gateway: 192.168.0.254 Group Master INPUT USB PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL DIGITAL MIXING ENGINE SATELLITE INPUT DME Satellite (IP address: 192.168.0.5) Connecting to an External Device Control from a computer with a different subnet Switching Hub Ethernet Straight Cable Ethernet Cable Ethernet Straight Cable Computer Ethernet Straight Cable INPUT USB Router or Layer-3 Compliant Switching Hub PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL Other Functions Ethernet Cable DIGITAL MIXING ENGINE SATELLITE INPUT SCENE HOME UTILITY References DME Satellite (IP address: 192.168.0.3) (Master ID: 5) LEVEL MUTE CANCEL ENTER DME64N/24N (IP address: 192.168.0.12) (Master ID: 5) DME8i-C/DME8o-C/DME4io-C Owner’s Manual 25  Foreword Connecting to a Computer Connecting multiple device groups Device Group 1 Device Group 2 Introduction to the DME Satellite Group Master Group Master INPUT USB INPUT PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL DIGITAL MIXING ENGINE SATELLITE USB PEAK PEAK SIGNAL SIGNAL PEAK PEAK PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL SIGNAL SIGNAL INPUT DIGITAL MIXING ENGINE SATELLITE INPUT DME Satellite (IP address: 192.168.0.2) Ethernet Cable DME Satellite (IP address: 192.168.0.3) Ethernet Cable Switching Hub Switching Hub Controls and Connectors Ethernet Straight Cable Ethernet Straight Cable Ethernet Straight Cable Ethernet Cable SCENE Connecting to a Computer HOME UTILITY LEVEL MUTE CANCEL ENTER SCENE DME64N/24N (IP address: 192.168.0.100) (Master ID: 2) Ethernet Cable HOME UTILITY LEVEL MUTE CANCEL ENTER DME64N/24N (IP address: 192.168.0.200) (Master ID: 3) INPUT USB INPUT PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL DIGITAL MIXING ENGINE SATELLITE USB PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL SIGNAL SIGNAL SIGNAL INPUT DIGITAL MIXING ENGINE SATELLITE INPUT DME Satellite (IP address: 192.168.0.40) (Master ID: 2) DME Satellite (IP address: 192.168.0.10) (Master ID: 3) Audio I/O Connection Connecting to an External Device Computer (IP address: 192.168.0.1) Other Functions References 26 PEAK SIGNAL PEAK SIGNAL DME8i-C/DME8o-C/DME4io-C Owner’s Manual  Foreword Audio I/O Connection The DME Satellite CobraNet connectors enable you to transfer digital audio, control, and word clock signals. Refer to page 15 for more information on CobraNet. Connecting and setting up the DME Satellite in accordance with other CobraNet compatible equipment allows for broad-ranging audio and word clock signal networkability. Refer to the MY16-C or MY16-CII Owner’s Manual for more information on the corresponding interface card. Controls and Connectors Example: Connection to CobraNet devices INPUT PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL DIGITAL MIXING ENGINE SATELLITE INPUT DME Satellite ACU16-C Audio Signal Audio Signal Switching Hub Audio Signal Audio Signal MY16-CII 1 2 NETWORK 96kHz MID 88.2kHz MASTER 3 4 3 4 5 6 7 8 5 6 7 8 Ethernet Straight Cable PEAK IN SIGNAL 48kHz 1 2 44.1kHz PEAK SCENE NUMBER SIGNAL NETWORK HUB AND BRIDGE OUT LINK CONDUCT LOCK DME24N ERROR 88 NHB32-C Audio I/O Connection EXT. CLOCK Connecting to a Computer USB Introduction to the DME Satellite Digital Audio Connection (CobraNet Connectors) References Other Functions Control data such as MIDI messages can be transferred between the DME Satellite and an MY16-C or MY16-CII via the CobraNet network. However, some devices, even with an MY card installed, might be unable to transmit or receive control data. For details, refer to the owner’s manual for the device in which you plan to install the interface card. Connecting to an External Device NO T E DME8i-C/DME8o-C/DME4io-C Owner’s Manual 27  Foreword Audio I/O Connection Analog Audio Connection ([INPUT] & [OUTPUT] Connectors) Introduction to the DME Satellite The DME Satellite can directly input and output audio signals via the [INPUT] and [OUTPUT] connectors. Wire the supplied Euroblock plugs (3P) as shown below. You can use DME Designer to set the head amplifier gain and turn the phantom power on and off for each [INPUT] connector. Cable preparation Prepare cables to be attached to a Euroblock plug as shown below. Shielded Cable 7mm Controls and Connectors 30mm Be sure to use shielded cables. CAUTION Do not tin (plate with solder) the exposed sections of the cable. Connecting to a Computer CAUTION Euroblock plug connection N OT E Audio I/O Connection Use a slotted screwdriver with a blade width of about 3 millimeters to secure the cables to the (3P) Euroblock plug. Use a slotted screwdriver with a blade width of about 2 millimeters to secure the cables to the (16P) Euroblock plug to connect to the [GPI] connector. 1. Loosen terminal screws. 3mm Loosen Slotted Screwdriver Terminal Screw Connecting to an External Device Other Functions References 28 Euroblock Plug 2. Insert cables. 3. Securely tighten terminal screws. Pull the cables (not too strongly) to confirm that they are securely connected. 4. Insert the Euroblock plug into the Euroblock connector on the rear panel. DME8i-C/DME8o-C/DME4io-C Owner’s Manual  Foreword Connecting to an External Device Controlling external head amplifiers from the DME Satellite Connecting to a Computer You can remotely control the AD8HR or AD824 head amplifier settings from DME Designer. Up to eight AD8HR/AD824 head amplifiers can be connected. Be sure to set the dip switch on the rear panel of the DME Satellite to “RS-422” (page 20) when connecting to AD8HR or AD824 remote head amplifiers. Do not change the dip switch setting to any position other than to “RS-422” while the devices are connected to prevent possible damage to the device(s). When connecting to a combination of AD8HR and AD824 head amplifiers, be sure to place the AD8HR units closest to the DME Satellite in the chain, otherwise the AD8HR or AD824 unit(s) may not be properly recognized by the DME Satellite. D-SUB 9-pin Cable (Interlink Crossover) REMOTE INPUT PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL DIGITAL MIXING ENGINE SATELLITE INPUT DME Satellite HA REMOTE 1 HA REMOTE 2 AD8HR COM PC/RS-422 AD824 HA REMOTE 1 HA REMOTE 2 AD8HR COM RS-422 COM PC/RS-422 COM RS-422 AD824 COM PC/RS-422 AD824 NO T E Only control signals are transmitted and received via the REMOTE connection. Audio connections must be made separately. Audio I/O Connection USB Connecting to an External Device Set to RS-422 Controls and Connectors The [REMOTE] connector of the DME Satellite can be connected to remotely-controllable Yamaha AD8HR or AD824 head amplifiers (pre-amps), or RS-232C compatible controllers (such as those from AMX or Crestron). The [REMOTE] connector also transmits and receives MIDI messages. Introduction to the DME Satellite Remote Connection ([REMOTE] Connector) NO T E Refer to “DME-N Remote Control Protocol Specifications” on the Yamaha web site for more information on communication protocols used to control the DME Satellite from an external device (such as those from AMX or Crestron). http://www.yamahaproaudio.com/ DME8i-C/DME8o-C/DME4io-C Owner’s Manual References You can remotely control the DME Satellite from a connected RS-232C or RS-422 compatible controller, such as those from AMX or Crestron. Be sure to set the dip switch on the rear panel of the DME Satellite correctly (page 20) in accordance with a connected RS-232C or RS-422 compatible remote controller. Do not change the dip switch setting to any other position while the devices are connected to prevent possible damage to the device(s). Other Functions Controlling the DME Satellite from an external device 29  Foreword Connecting to an External Device CobraNet Connection (CobraNet Connectors) Introduction to the DME Satellite If you install an MY16-C or MY16-CII interface card on a PM5D Digital Mixing Consol and connect it to the DME Satellite via the CobraNet connectors, you can remotely control the DME Satellite from the PM5D, as well as transfer audio and word clock signals between them. Refer to the PM5D/PM5D-RH Owner’s Manual for more information on the PM5D’s DME Control function. DME8i-C Ethernet INPUT USB PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL DIGITAL MIXING ENGINE SATELLITE INPUT CobraNet Controls and Connectors DME8i-C Ethernet Switching Hub INPUT USB PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL DIGITAL MIXING ENGINE SATELLITE INPUT Hub CobraNet Switching Hub DME8o-C Hub DME8o-C Connecting to a Computer Hub DME4io-C DME4io-C MY16-CII MY16-CII Audio I/O Connection PM5D Connecting to an External Device N OT E • You can control multiple DME series units from a PM5D. Specify the same device group for each DME series unit you want to control. • If you have connected a PM5D and a DME Satellite via CobraNet and are controlling the DME Satellite from the PM5D, you must specify a value of 2 as the fourth octet of the group master DME Satellite’s IP address. Other Functions References 30 DME8i-C/DME8o-C/DME4io-C Owner’s Manual  Foreword Connecting to an External Device • For more information on the CP4SW, CP4SF, and CP1SF Control Panels, refer to the CP4SW/CP4SF/ CP1SF Owner’s Manual. • You can use DME Designer to set up the system so that scene recall operations and User Defined parameter control can be carried out from connected GPI control devices. Refer to the DME Designer Owner’s Manual for details. IN GPI Connection IN +V +V GPI Connection OUT GND GND Audio I/O Connection GPI Connection Example: Lighting LED indicators on the external devices from the DME Satellite Max. 16mA CAUTION DME Satellite [GPI] Connector DME Satellite [GPI] Connector Euroblock Plug Euroblock Plug Remote Switch Box Remote Fader Box 4 3 2 Switches 1 Make sure that the current between the OUT and GND [GPI] connectors is less than 16mA. Connecting to an External Device Continuous Variable Volume DME Satellite [GPI] Connector Euroblock Plug Remote LED Box 4 3 2 1 10k ohm Linear Taper Potentiometer 4 3 2 1 Other Functions Example: Controlling the DME Satellite via a 10k ohm linear taper potentiometer. LEDs and Resistors NO T E You can use DME Designer to adjust the input calibration parameters for the [GPI] connector. DME8i-C/DME8o-C/DME4io-C Owner’s Manual References Example: Controlling the DME Satellite from a switch box Controls and Connectors NO T E Connecting to a Computer A GPI (General Purpose Interface) device (GPI controller, etc.) can be connected to the rear panel [GPI] connectors to enable the transfer of a variety of control signals. Optional CP4SW, CP4SF, and CP1SF Control Panels can be also connected via GPI. The DME Satellite features 8-port GPI input and 4-port GPI output. The +V terminals have an output voltage of 5 volts. The IN terminal detects voltage changes from 0V to 5V. The OUT terminals output either signal “L” or “H” at a TTL level. The parameters for each GPI input and output are assigned via the DME Designer application. Euroblock connectors are used for all GPI input and output connections. Euroblock connection methods are described in “Euroblock plug connection” on page 28 in this manual. Introduction to the DME Satellite GPI Connection ([GPI] Connector) 31  Foreword Other Functions Initializing the DME Satellite Introduction to the DME Satellite You can initialize the DME Satellite internal memory. Select one of the following initialization types: Initialize DME: All scenes and preset parameter settings, excluding components, WAVE files, and files saved via the File Storage function will be deleted. The Utility settings will be set to default values. Controls and Connectors Delete All Data: All stored component, scene, and preset parameter settings, WAVE files, and files saved via the File Storage function will be deleted. The Utility settings will be set to default. Use this initialization type if the internal data is damaged or corrupted. After initialization, transfer necessary components from DME Designer. 1. While the DME Satellite is turned off, set the dip switch on the rear panel to the following position, then turn on the power to the unit. Connecting to a Computer RS-232C Initialize DME: RS-422 RS-232C Delete All Data: RS-422 Audio I/O Connection Four [PEAK] indicators on the upper row on the front panel light up during the initialization process. Four [SIGNAL] indicators on the lower row of the front panel flash when the initialization process is complete. Four [PEAK] indicators on the lower row of the front panel flash if the initialization process fails. CAUTION Do NOT turn off the power to the DME Satellite during the initialization process to prevent possible damage to the device. Connecting to an External Device 2. When initialization is complete, reset the dip switch to its previous position (page 20), then turn off and on the power to the unit. Be sure to reset the dip switch to the previous position to prevent possible damage to the device. CAUTION Other Functions References 32 DME8i-C/DME8o-C/DME4io-C Owner’s Manual  Foreword References ICP1 CONTROL PANEL CP4SW 10 10 10 10 10 0 0 0 0 0 CONTROL PANEL CONTROL PANEL CP4SF CP1SF DME8i-C/DME8o-C/DME4io-C Owner’s Manual Other Functions These controllers connect to DME series units via the [GPI] connectors. These controllers control only the DME series units to which they are directly connected. The controller switches enable you to turn the parameter settings On and Off. The switch LEDs enable you to check the parameter status. The faders enable you to control the parameter values. References CP4SW, CP4SF, and CP1SF Connecting to an External Device Audio I/O Connection Connecting to a Computer This controller connects to a DME series unit via Ethernet. Like the DME series units, a unique IP address must be assigned to each controller unit. Data is transmitted and received via Ethernet cables. You can assign and control any function of all DME series units in the same device group via the controller. Up to four parameter sets can be assigned to six function keys (F1 – F6) located above and under the LCD. You can control up to 24 parameters by selecting a display page using the [HOME] key. Controls and Connectors The ICP1, CP4SW, CP1SF, and CP4SF controllers are available as options for remote external control of the DME series. The ICP1 connects via Ethernet, while the CP4SW, CP1SF, and CP4SF connect via the GPI interface. For more information on installing your Control Panel and connecting it to a DME series unit, refer to the owner’s manual that came with the Control Panel. For more information on settings, refer to the DME Designer Owner’s Manual. Introduction to the DME Satellite Options 33  Foreword References Troubleshooting Introduction to the DME Satellite Controls and Connectors Connecting to a Computer Audio I/O Connection Connecting to an External Device The device does not turn on, or the panel LEDs do not light up. • Connect the power cord properly (page 7). • Make sure that the [POWER] switch is turned ON (page 19). • If the device still does not turn on, contact a Yamaha dealer. No communication between the DME Satellite and the DME Designer application software. • Connect the cable properly (page 22, 24). • Make sure that USB-MIDI Driver has been installed correctly. • If the [NETWORK] connector is being used for connection, make sure that you have set the DME-N Network Driver correctly. • Make the “MIDI Setup” settings. • The DME Designer version should be 2.0.0 or later. • Make the Port setting. No audio input is present. • • • • No audio is output. • Connect the cable properly. • Make sure that the CobraNet bundle and latency settings are correct. • Make sure that the number of CobraNet multicast bundles is not exceeding the recommended maximum number. • Depending on the type of switching hub and connection method, extra network resources may have been used, resulting in interruption of audio signals. • Make sure that the output level set in DME Designer is not too low. • Make sure that the Mute setting in DME Designer is set to Off. • You may have designed a scene in DME Designer that mutes audio output. • You may have tried to use a configuration at 96 kHz that does not support 96 kHz. The selected scene changes unexpectedly. • Use DME Designer to check the MIDI Program Change assignments. • Use DME Designer to check the GPI input assignments. MIDI messages cannot be transmitted or received. • Make sure that the power to the MIDI device is turned on. • Set the MIDI port properly. • Set the receive and transmit channels properly. Scenes cannot be recalled via MIDI Program Change messages. • Use DME Designer to change the setting so that the required MIDI Program Change messages will be received properly. • Make the appropriate Program Change Table settings via DME Designer. Parameters cannot be controlled via MIDI Control Change messages. • Use DME Designer to set the parameters correctly to allow Control Change message reception. • Make the appropriate MIDI Control Change Table settings via DME Designer. Parameters cannot be edited via MIDI Parameter Change messages. • Use DME Designer to set the parameters correctly to allow Parameter Change message reception. • Make the appropriate MIDI Parameter Change Table settings via DME Designer. Data transmission speed is slow when the DME64N/24N is also being used. • Select 100Base-TX for Link Mode on all devices. • If you assigned the DME64N/24 as the group master, re-assign the group master to be the DME Satellite. Connect the cable properly. Check to see if signals are being received from an external device. Make sure that the CobraNet bundle and latency settings are correct. Set the gain of the internal head amplifier or external head amplifier to an appropriate level. Other Functions Component Refer to the DME Designer Owner’s Manual for more information on each component. References 34 DME8i-C/DME8o-C/DME4io-C Owner’s Manual  Foreword References MIDI Data Format MIDI Control Change and Parameter Change messages transmitted to the DME8i-C/DME8o-C/DME4io-C can be used to control parameters according to the “MIDI Control Change Table” and “MIDI Parameter Change Table” assignments. When a parameter is edited via DME Designer, corresponding MIDI Control Change and Parameter Change messages are also transmitted by the DME8i-C/DME8o-C/DME4ioC as specified by the “MIDI Control Change Table” and “MIDI Parameter Change Table” assignments. “MIDI Program Change Table,” “MIDI Control Change Table,” and “MIDI Parameter Change Table” assignments can be made via DME Designer. Refer to the DME Designer Owner’s Manual for details. 2. MIDI Data Flow MIDI IN MIDI Rx CH SW1 Bank Select MSB/LSB Program Change (Scene Recall) SW2 Control Change (Parameter Edit) SW3 Parameter Change (Parameter Edit) 3.3 MIDI Rx Channel Specifies the MIDI receive channel (1 ~ 16). 3.4 MIDI Tx Switch Program Change Tx Switch: turns Bank Select MSB, LSB, and Program Change transmission on or off. Control Change Tx Switch: turns Control Change transmission on or off. Parameter Change Tx Switch: turns Parameter Change transmission on or off. 3.5 MIDI Rx Switch Program Change Rx Switch: turns Bank Select MSB, LSB, and Program Change reception on or off. Control Change Rx Switch: turns Control Change reception on or off. Parameter Change Rx Switch: turns Parameter Change reception on or off. 3.6 MIDI Omni Switch Program Change Omni Switch: turns the Bank Select MSB, LSB, and Program Change omni mode on or off. Control Change Omni Switch: turns the Control Change omni mode on or off. 3.7 MIDI Echo Back Switch Program Change Echo Back Switch: turns Bank Select MSB, LSB, and Program Change echo back on or off. Control Change Echo Back Switch: turns Control Change echo back on or off. Parameter Change Echo Back Switch: turns Parameter Change echo back on or off. Bank Select MSB/LSB Program Change (Echo Back) Other Functions SW4 Control Change (Echo Back) SW5 Parameter Change (Echo Back) SW6 Bank Select MSB/LSB Program Change Control Change SW7 MIDI Tx CH Controls and Connectors 3.2 MIDI Tx Channel Specifies the MIDI transmit channel (1 ~ 16). Connecting to a Computer 1.2 Parameter Control 3.1 Host Select Selects the input/output ports to be used for MIDI communication. Audio I/O Connection 1.1 Scene Change Scene recall occurs according to the “MIDI Program Change Table” assignments when appropriate MIDI Bank Select MSB/LSB and Program Change messages are received by the DME8i-C/ DME8o-C/DME4io-C. When a scene recall operation is carried out via DME Designer, corresponding MIDI Bank Select MSB/LSB and Program Change messages are also transmitted by the DME8i-C/DME8o-C/ DME4io-C as specified by the “MIDI Program Change Table” assignments. Transmission does not occur while configurations are being switched. Connecting to an External Device Specifies basic MIDI operation. Use DME Designer to make the setting. 1. MIDI functions on the DME8i-C, DME8o-C, and DME4io-C Introduction to the DME Satellite 3. MIDI Setup MIDI OUT SW8 Parameter Change SW9 References MIDI THRU SW1: Program Change Rx Switch [On/Off] SW2: Control Change Rx Switch [On/Off] SW3: Parameter Change Rx Switch [On/Off] SW4: Program Change Echo Back Switch [On/Off] SW5: Control Change Echo Back Switch [On/Off] SW6: Parameter Change Echo Back Switch [On/Off] SW7: Program Change Tx Switch [On/Off] SW8: Control Change Tx Switch [On/Off] SW9: Parameter Change MIDI Rx CH: MIDI Rx Channel (1-16) MIDI Tx CH: MIDI Tx Channel (1-16) DME8i-C/DME8o-C/DME4io-C Owner’s Manual 35  Foreword References Bank Select MSB 4. MIDI Format Number Format Notation Introduction to the DME Satellite Numbers ending with “h” are in hexadecimal format, while numbers ending with “b” are binary format. Characters “A” through “F” in hexadecimal numbers represent decimal values 10 through 15. Other lower-case characters (usually “n” or “x”) can represent any number. Status Data Bnh (1101nnnnb) 00h (00000000b) Data nnh (0nnnnnnnb) Bank Select LSB Status Data MIDI Format Chart (Rx: receive, Tx: transmit} Command Rx/Tx Control Change Control Change No. 0 (Bank Select MSB) Control Value (Bank Select MSB No.) Bnh (1101nnnnb) 20h (00100000b) nnh (0nnnnnnnb) Control Change Control Change No. 32 (Bank Select LSB) Control Value (Bank Select LSB No.) Function Program Change No. Controls and Connectors Channel Message System Real-time Message Connecting to a Computer System Exclusive Message Control Change (Bnh) Rx/Tx Editing the parameters Program Change (Cnn) Rx/Tx Scene Recall 4.2 Active Sensing (FEh) TIMING CLOCK (F8h) Rx MIDI Clock Receive ACTIVE SENSING (FEh) Rx MIDI Cable Check Receive MIDI communication will be initialized if no data is received within 300 ms after reception (Running Status, etc., will be cleared). Rx/Tx Editing the parameters Parameter Change Audio I/O Connection Connecting to an External Device Other Functions Cnh (1100nnnnb) nnh (0nnnnnnnb) Program Change Program Change No. (0-127) Active Sensing Status FEh (11111110b) Active Sensing 4.3 Control Change (Bnh) 4.1 Program Change (Cnh) Receive When the “Program Change Rx Switch” is on, Program Change messages are received on the MIDI channel specified by the “MIDI Rx Channel” parameter. If the “Program Change Omni Switch” is also on, however, Program Change messages will be received on all MIDI channels regardless of the “MIDI Rx Channel” setting. When a Program Change message is received, the scene assigned to the received program number in the “MIDI Program Change Table” is recalled. The effective Bank Select, Program Change range is as follows: Bank Select MSB: 0 Bank Select LSB: 0-7 Program Change No.: 0-127 Transmit When the “Program Change Tx Switch” is on and a scene is switched from DME Designer, the corresponding Program Change number will be transmitted as specified by the “MIDI Program Change Table” and “MIDI Tx Channel” settings. Transmission does not occur when a scene with a different configuration is selected. If multiple Program Change numbers are assigned to a single scene, the Bank Select MSB/LSB and Program Change number corresponding to the lowest number will be transmitted. References 36 Status Data DME8i-C/DME8o-C/DME4io-C Owner’s Manual Receive When the “Control Change Rx Switch” is on, Control Change messages are received on the MIDI channel specified by the “MIDI Rx Channel” parameter. If the “Control Change Omni Switch” is also on, however, Control Change messages will be received on all MIDI channels regardless of the “MIDI Rx Channel” setting. Control Change parameter resolution is 128 regardless of the effective range of the parameter. For finer settings use Parameter Change. Transmit When the “Control Change Tx Switch” is on and a parameter is edited via DME Designer, appropriate Control Change data will be transmitted as specified by the “MIDI Control Change Table” and “MIDI Tx Channel” settings. Refer to “Supplementary Information 1” for cases in which multiple messages are assigned to a single parameter. Status Data Bnh (1011nnnnb) cch (0cccccccb) vvh (0vvvvvvvb) Control Change Control Change No. (1-31,3395,102-119) Control Value (0-127) 4.4 Parameter Change (F0h - F7h) Receive When the “Parameter Change Rx Switch” is On, Parameter Change messages are received on the MIDI channel specified by the “Device ID (Rx Ch)” parameter.  Foreword aah Parameter ddh Data Value ddh ddh ddh ddh EOX F7h (0aaaaaaab) (0dddddddb) Parameter Address Low data 0 (0dddddddb) (0dddddddb) (0dddddddb) (0dddddddb) (11110111b) data 1 data 2 data 3 data 4 End of Exclusive Supplementary Information 2 Setting the Parameter Change Message Parameter Data Values The Parameter change parameter values are expressed as 32-bit integers with or without parity. • A parity bit (positive:0, negative:1) is added above the most significant value bit (bit 31). • Fractional parameters will be converted according to the integer table. • For integers with parity, negative numbers are expressed as the 2’s complement. parity bit0 bit1 bit2 bit3 bit4 bit5 bit6 bit7 bit8 bit9 bit10 bit11 bit12 bit13 bit14 bit15 bit16 bit17 bit18 bit19 bit20 bit21 bit22 bit23 bit24 bit25 bit26 bit27 bit28 bit29 bit30 bit31 0 0 data 0 data 1 data 2 data 3 data 4 Example: • Decimal value 1000 → Hexadecimal value 3E8h Positive 0 0 0 0 0 3 E 8 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 0 1 0 0 0 data 0 = 00h data 1 = 00h data 2 = 00h data 3 = 07h data 4 = 68h • Decimal value 1000 → Hexadecimal value FFFFFC18h (2’s complement of 3E8h) Negative F F F F F C 1 8 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 1 1 0 0 0 data 0 = 1Fh data 1 = 7Fh data 2 = 7Fh data 3 = 78h Introduction to the DME Satellite (0001xxxxb) (00111110b) (00010000b) (0aaaaaaab) Controls and Connectors 1xh 3Eh 10h aah Connecting to a Computer DEVICE ID. GROUP ID. MODEL ID. Parameter Address System Exclusive Message Manufacturer’s ID No.(YAMAHA) Rx/Tx Channel (0-15) Digital Mixer Device Code (DME) Parameter Address High Audio I/O Connection F0h (11110000b) 43h (01000011b) Other Functions Status ID No. Supplementary Information 1 Messages Transmitted When Multiple Messages are Assigned to the Same Parameter The DME8i-C/DME8o-C/DME4io-C MIDI transmit messages are specified via the “MIDI Control Change Table” and “MIDI Parameter Change Table.” (The “MIDI Control Change Table” and “MIDI Parameter Change Table” can be set up via DME Designer.) Multiple messages can be assigned to a single parameter, but the DME8i-C/DME8o-C/DME4io-C will only transmit one of the assigned messages. The transmitted messages are as follows: • If a Control Change message and a Parameter Change message are assigned to the same parameter → the Control Change message will be transmitted. • If multiple Control Change numbers are assigned to the same parameter → the smallest Control Change number message will be transmitted. • If multiple Parameter Change numbers are assigned to the same parameter → the smallest Parameter Change number message will be transmitted. data 4 = 18h DME8i-C/DME8o-C/DME4io-C Owner’s Manual References Transmit When the “Parameter Change Tx Switch” is On and a parameter is edited via DME Designer, appropriate Parameter Change data will be transmitted as specified by the “MIDI Parameter Change Table” and “MIDI Tx Channel” settings. Refer to “Supplementary Information 1” for cases in which multiple messages are assigned to a single parameter. Refer to “Supplementary Information 2” for information on setting Parameter Data values. Connecting to an External Device References 37  Foreword MIDI Implementation Chart YAMAHA [Digital Mixing Engine Satellite] Model DME8i-C, DME8o-C, DME4io-C MIDI Implementation Chart Function... Transmitted Recognized Introduction to the DME Satellite Basic Channel Default Changed 1 - 16 1 - 16 1 - 16 1 - 16 Mode Default Messages Altered ˛ ˛ ˛ ˛ ˛ Controls and Connectors Note Number : True voice ************** ************** Connecting to a Computer Note ON ˛ Note OFF ˛ ˛ ˛ After Touch Key's Ch's ˛ ˛ ˛ ˛ ˛ ˛ 0,32 1-31,33-95,102-119 *1 *2 Ø Ø 0 - 127 *1 ************** Ø *3 Ø Ø Ø Remarks Memorized ˛ ˛ ˛ Velocity Pitch Bend Date :16-FEB-2006 Version : 1.0 *1 *2 Bank Select Assignable Control Audio I/O Connection Change Connecting to an External Device Prog Change Ø : True # System Exclusive Other Functions Common Ø : Song Pos. ˛ : Song Sel. ˛ : Tune ˛ ˛ ˛ ˛ ˛ : : : Mes- : sages: : ˛ ˛ ˛ ˛ ˛ ˛ ˛ ˛ ˛ ˛ Ø ˛ References All Sound Off Reset All Cntrls Local ON/OFF All Notes OFF Active Sense Reset *1 *3 Assignable ˛ ˛ ˛ System : Clock Real Time : Commands Aux 0 - 127 0 - 127 Notes: *1 transmit/receive if program change switch is on. *2 transmit/receive if control change switch is on. *3 transmit/receive if parameter change switch is on. Mode 1 : OMNI ON , POLY Mode 3 : OMNI OFF, POLY 38 DME8i-C/DME8o-C/DME4io-C Owner’s Manual Mode 2 : OMNI ON ,MONO Mode 4 : OMNI OFF,MONO Ø ˛ : Yes : No  Foreword References Display Messages Flashing Lit PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL Flashing Lit PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL Flashing Lit PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL Flashing Lit Lit PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL Action A system error has occurred. Execute the “Initialize DME” operation, then restart it. If the error indicators are still indicating the error, execute the “Delete All Data” initialization. If the problem persists, contact a Yamaha dealer. Data inside the internal flash memory has been erased. The firmware update operation may have failed. Use DME Designer to execute the Recovery update operation. If the problem persists, contact a Yamaha dealer. The internal battery is completely discharged or not installed. If you turn off the power to the unit, the current settings will be lost and reset to the default values. Stop operating the unit, and contact a Yamaha dealer regarding battery replacement. A scene recall attempt has failed. Use DME Designer to recall the scene again. If the problem persists, contact a Yamaha dealer. Audio is not input or output and is muted due to insufficient DSP resources. This error sometimes occurs if you try to operate a configuration at 96 kHz that has been created with a word clock of 48 kHz. To operate a configuration at any word clock setting, use DME Designer to create a configuration with the word clock set to 96 kHz. The network is not communicating properly. Connect the network cables properly, and make sure that the network devices are operating correctly. Duplicate IP addresses. Connect your computer to the DME Satellite via USB, then set a unique IP address. The DME Satellite contains data for a different device group or no data. Send data appropriate for the actual device configuration from DME Designer. Flashing Lit PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL Controls and Connectors Error Connecting to a Computer Indicator Audio I/O Connection Error Messages Introduction to the DME Satellite The [ERROR] and [PEAK] indicators on the front panel of the DME Satellite indicate error and warning messages. Lit PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL Lit PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL Other Functions Flashing Connecting to an External Device Flashing Flashing Indicator Flashing rapidly Flashing slow PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL PEAK PEAK PEAK SIGNAL SIGNAL SIGNAL Error Action The internal battery is almost discharged. Your data may be lost. If you turn off the power to the unit, the current settings may be lost and reset to the default values. Stop operating the unit, and contact a Yamaha dealer regarding battery replacement. The backup battery voltage is low. This does not affect the operation of the unit. However, if you continue using the unit, the settings may be lost and reset to the default values. Contact a Yamaha dealer regarding battery replacement at your earliest convenience. DME8i-C/DME8o-C/DME4io-C Owner’s Manual References Warning Messages 39  Foreword References General Specifications Sampling Frequency Introduction to the DME Satellite Normal Rate:48kHz Double Rate:96kHz (±37ppm for conductor) (±50ppm for performer) Maximum Voltage Gain Miscellaneous Gain: –60dB, RL:600Ω, 64dB INPUT to OUTPUT Power Consumption 40W Dimensions (HxDxW) 44x361x480 mm Net Weight 4.4kg Controls and Connectors Temperature range AC Power cord, CD-ROM (DME Designer application), Mini Euro plug(16P)x1, Euro plug(3P)x8, Owner’s Manual, DME Designer Installation Guide, Rubber feetx4 Include Accessories Connecting to a Computer Electrical Characteristics Output impedance of signal generator: 150 Ω DME8i-C : Measured with DME8o-C DME8o-C : Measured with DME8i-C Frequency Response Audio I/O Connection Connecting to an External Device Other Functions References 40 operating: 5 to 40˚C storage: –20 to 60˚C fs=48kHz@20Hz–20kHz, reference to the nominal output level @1kHz fs=96kHz@20Hz–40kHz, refelence to the nominal output level @1kHz <DME8i-C> Input INPUT 1–8 Output OUTPUT 1–8 RL CONDITIONS MIN TYP MAX UNITS input level: –60dBu, GAIN: –60dB –1.5 0.0 +0.5 dB input level: +10dBu, GAIN: +10dB –1.5 0.0 +0.5 dB 600Ω <DME8o-C> Input Output RL CONDITIONS MIN TYP MAX UNITS INPUT 1–8 OUTPUT 1–8 600Ω input level: +10dBu, GAIN: +10dB –1.5 0.0 +0.5 dB Input Output RL CONDITIONS MIN TYP MAX UNITS INPUT 1–4 OUTPUT 1–4 600Ω <DME4io-C> Gain Error input level: –60dBu, GAIN: –60dB –1.5 0.0 +0.5 dB input level: +10dBu, GAIN: +10dB –1.5 0.0 +0.5 dB CONDITIONS MIN TYP MAX UNITS @1kHz <DME8i-C> Input Output RL INPUT 1–8 OUTPUT 1–8 600Ω input level: –60dBu, GAIN: –60dB +2.0 +4.0 +6.0 dBu input level: +10dBu, GAIN: +10dB +2.0 +4.0 +6.0 dBu <DME8o-C> Input Output RL CONDITIONS MIN TYP MAX UNITS INPUT 1–8 OUTPUT 1–8 600Ω input level: +10dBu, GAIN: +10dB +2.0 +4.0 +6.0 dBu DME8i-C/DME8o-C/DME4io-C Owner’s Manual  Foreword References Output RL INPUT 1–4 OUTPUT 1–4 600Ω Total Harmonic Distortion CONDITIONS MIN TYP MAX UNITS input level: –60dBu, GAIN: –60dB +2.0 +4.0 +6.0 dBu input level: +10dBu, GAIN: +10dB +2.0 +4.0 +6.0 dBu MIN TYP MAX UNITS +4dB@20Hz–20kHz, 20Hz–40kHz (fs=96kHz), GAIN: –60dB 0.1 % +4dB@20Hz–20kHz, 20Hz–40kHz (fs=96kHz), GAIN: +10dB 0.05 % +22dB@1kHz, GAIN: +10dB 0.015 % MAX UNITS fs=48kHz or 96kHz <DME8i-C> Input INPUT 1–8 Output OUTPUT 1–8 RL CONDITIONS 600Ω Controls and Connectors Input Introduction to the DME Satellite <DME4io-C> Input Output RL CONDITIONS MIN TYP % OUTPUT 1–8 600Ω +4dB@20Hz–20kHz, 20Hz–40kHz (fs=96kHz), GAIN: +10dB 0.05 INPUT 1–8 +22dB@1kHz, GAIN: +10dB 0.015 % MAX UNITS +4dB@20Hz–20kHz, 20Hz–40kHz (fs=96kHz), GAIN: –60dB 0.1 % +4dB@20Hz–20kHz, 20Hz–40kHz (fs=96kHz), GAIN: +10dB 0.05 % +22dB@1kHz, GAIN: +10dB 0.015 % TYP MAX UNITS –128 EIN –127 EIN dBu Connecting to a Computer <DME8o-C> Input INPUT 1–4 Output OUTPUT 1–4 RL CONDITIONS 600Ω MIN TYP Audio I/O Connection <DME4io-C> Input Output RL CONDITIONS MIN Rs=150Ω, GAIN: –60dB All input & output level controls: 0dB INPUT 1–8 OUTPUT 1–8 600Ω –64 Rs=150Ω, GAIN: +10dB All input & output level controls: 0dB dBu –82 –79 dBu TYP MAX UNITS –82 –79 dBu <DME8o-C> Input INPUT 1–8 Output OUTPUT 1–8 RL CONDITIONS 600Ω Rs=150Ω, GAIN: +10dB All input & output level controls: 0dB MIN DME8i-C/DME8o-C/DME4io-C Owner’s Manual Other Functions fs=48kHz or 96kHz, EIN=Equivalent Input Noise <DME8i-C> References Hum&Noise Connecting to an External Device * Total Harmonic Distortion is measured with a 18dB/octave filter @80kHz. 41  Foreword References <DME4io-C> Input Output RL CONDITIONS MIN Introduction to the DME Satellite Rs=150Ω, GAIN: –60dB All input & output level controls: 0dB INPUT 1–4 OUTPUT 1–4 600Ω TYP MAX UNITS –128 EIN EIN –127 dBu –64 Rs=150Ω, GAIN: +10dB All input & output level controls: 0dB –82 dBu –79 dBu * Hum & Noise are measured with a 6dB/octave filter @12.7kHz; equivalent to a 20kHz filter with infinite dB/octave attenuation. Controls and Connectors Dynamic Range fs=48kHz or 96kHz <DME8i-C/DME8o-C> Input Output RL CONDITIONS INPUT 1–8 OUTPUT 1–8 600Ω GAIN: +10dB Input Output RL CONDITIONS INPUT 1–4 OUTPUT 1–4 600Ω GAIN: +10dB MIN TYP MAX 106 UNITS dB <DME4io-C> Connecting to a Computer MIN TYP MAX 106 UNITS dB * Dynamic range are measured with a 6dB/octave filter @12.7kHz; equivalent to a 20kHz filter with infinite dB/octave attenuation. Crosstalk@1kHz reference to the level of output N <DME8i-C/DME8o-C> Audio I/O Connection from to CONDITIONS INPUT N OUTPUT (N–1) or (N+1) N = 1–8, GAIN: +10dB from to CONDITIONS INPUT N OUTPUT (N–1) or (N+1) N = 1–4, GAIN: +10dB MIN TYP MAX UNITS –80 dB MAX UNITS –80 dB MAX UNITS <DME4io-C> MIN TYP Connecting to an External Device * Crosstalk is measured with a 18dB/octave filter @80kHz LED Level Meter <DME8i-C> Other Functions METERING POINT MIN TYP PEAK red LED: ON –3 dBFs SIGNAL green LED: ON –40 dBFs INPUT 1–8 <DME8o-C> METERING POINT References 42 CONDITIONS CONDITIONS MIN TYP MAX UNITS PEAK red LED: ON –3 dBFs SIGNAL green LED: ON –40 dBFs OUTPUT 1–8 DME8i-C/DME8o-C/DME4io-C Owner’s Manual  Foreword References <DME4io-C> MIN TYP MAX UNITS INPUT 1–4 OUTPUT 1–4 PEAK red LED:ON –3 dBFs SIGNAL green LED:ON –40 dBFs PARAMETER CONDITIONS Signal Delay MIN CobraNET Latency: 5.33msec ANALOG INPUT to ANALOG OUTPUT@96KHz CobraNET Latency: 2.67msec CobraNET Latency: 1.33msec TYP MAX UNITS 6.12 msec 3.45 msec 2.12 msec Introduction to the DME Satellite CONDITIONS Controls and Connectors METERING POINT Input/Output Characteristics For Use With Nominal 3kΩ 50–600Ω Mics & 600Ω Lines Input Level –60dB +10dB Connector Nominal Max.before clip –60dBu (0.775mV) –40dBu (7.75mV) +10dBu (2.45V) +30dBu (24.5V) EUROBLOCK (5.08mm pitch) ANALOG OUTPUT CHARACTERISTICS Output Terminals Actual Source Impedance For Use With Nominal 75Ω 600Ω Lines Output level Nominal Max. before clip +4dBu (1.23 V) +24dBu(12.28V) <DME8o-C> CH OUTPUT 1–8 <DME4io-C> CH OUTPUT 1–4 Connector EUROBLOCK (5.08mm pitch) *1.In these specifications, 0dBu is referenced to 0.775 Vrms. *2.All AD converters are 24-bit linear, 128-times oversampling (Fs=48kHz)/64-times oversampling (Fs=96kHz). DIGITAL INPUT & OUTPUT CHARACTERISTICS Terminal Format Data length Level Connector CobraNet CobraNet 16/20/24bit 100Base-TX RJ-45x2 *1 References *1.PRIMARY,SECONDARY *2.Double Channel format and Single format are supported at 96kHz. Audio I/O Connection <DME4io-C> CH INPUT 1–4 Actual Load Impedance Connecting to an External Device <DME8i-C> CH INPUT 1–8 GAIN Other Functions Input Terminals Connecting to a Computer ANALOG INPUT CHARACTERISTICS DME8i-C/DME8o-C/DME4io-C Owner’s Manual 43  Foreword References CONTROL I/O CHARACTERISTICS Terminal Introduction to the DME Satellite Format Level Connector IN – 0–5V EUROBLOCK *1 (3.5mm pitch) OUT – TTL +V – 5V Ethernet IEEE802.3 10Base-T/100Base-TX RJ-45 USB USB 1.1 Function – Type B REMOTE RS-232C/RS-422 RS-232C/RS-422 D-SUB 9P (Male) GPI Controls and Connectors *1 Inputs: 8 channels, Outputs: 4 channels Inputs: Not apply 2 wire Fader mode Outputs: Imax/pin = 16mA Outputs: VH = 2.5V(min.), VL = 0.6V(max.) [NETWORK] Connector (100Base-TX Ethernet, RJ-45) Connecting to a Computer Pin Connection Audio I/O Connection 1 TxD+ 2 TxD– 3 RxD+ 4 Unused 5 Unused 6 RxD– 7 Unused 8 Unused Connecting to an External Device Straight and Crossover Cable Wiring Straight Cables Crossover Cables Pins Pins Other Functions 1 –– 1 1 –– 3 2 –– 2 2 –– 6 3 –– 3 3 –– 1 4 –– 4 4 –– 4 5 –– 5 5 –– 5 6 –– 6 6 –– 2 7 –– 7 7 –– 7 8 –– 8 8 –– 8 References 44 DME8i-C/DME8o-C/DME4io-C Owner’s Manual  Foreword References Controls and Connectors Rubber feet are included in the package. Unit: mm * Specifications and descriptions in this owner’s manual are for information purpose only. Yamaha Corp. reserves the right to charge or modify products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer. References Other Functions European models Purchaser/User Information specified in EN55103-1 and EN55103-2. Inrush Current: 35A Conforms to Environments: E1,E2,E3 and E4. Connecting to a Computer 480 44 Audio I/O Connection 1 440 Connecting to an External Device 354 3 361 (4) Introduction to the DME Satellite Dimensions DME8i-C/DME8o-C/DME4io-C Owner’s Manual 45  Foreword References Index Introduction to the DME Satellite A I About DME Designer ............................................................. 14 ICP1 ........................................................................................33 [AC IN] Connector ................................................................. 20 [IN USE/CONDUCTOR] Indicator ......................................19 Analog Audio Connection ....................................................... 28 Initialize DME .........................................................................32 area .......................................................................................... 10 Initializing ................................................................................32 [INPUT] & [OUTPUT] Connectors ......................................28 Controls and Connectors B [INPUT] Connectors ...............................................................21 Bundle ..................................................................................... 15 Input/Output Characteristics ...................................................43 C L CobraNet ................................................................................ 15 [LINK/ACTIVITY] Indicator ..................................................19 CobraNet Connection ............................................................. 30 Connecting to a Computer CobraNet [PRIMARY]/[SECONDARY] Connectors ............. 21 M Components ............................................................................ 10 MAC Address ...........................................................................21 conductor priority ................................................................... 17 Master and slave setting ............................................................23 Conductors ............................................................................. 17 [MASTER] Indicator ...............................................................18 Configuration .......................................................................... 10 MIDI Data Format ..................................................................35 CP4SW, CP4SF, and CP1SF .................................................. 33 MIDI Implementation Chart ...................................................38 multicast bundles .....................................................................16 D multi-unicast bundles ...............................................................16 Delete All Data ........................................................................ 32 Audio I/O Connection device group ............................................................................ 10 N Digital Audio Connection ....................................................... 27 [NETWORK] Connector ..................................................20, 44 Dimensions ............................................................................. 45 [NETWORK] Indicator ..........................................................18 Dip Switch .............................................................................. 20 Network Settings ......................................................................23 Display Messages ..................................................................... 39 Connecting to an External Device DME4io-C ................................................................................ 9 O DME8i-C .................................................................................. 9 octet .........................................................................................23 DME8o-C ................................................................................. 9 Options ....................................................................................33 [OUTPUT] Connectors ..........................................................21 E Other Functions Electrical Characteristics .......................................................... 40 P [ERROR] Indicator ................................................................. 19 parameters ................................................................................10 Error Messages ........................................................................ 39 [PEAK] Indicators ....................................................................19 Ethernet Connection ............................................................... 24 performers ................................................................................17 Euroblock plug connection ...................................................... 28 [POWER] Switch ....................................................................19 Precautions for Using a Rack-mounted DME Satellite ...............8 References F preset parameters ......................................................................10 Firmware Version ...................................................................... 7 primary ....................................................................................19 G R General Specifications ............................................................. 40 Remote Connection .................................................................29 GPI Connection ...................................................................... 31 [REMOTE] Connector ............................................................20 [GPI] Connector ..................................................................... 21 RS-232C ..................................................................................20 Ground Screw ......................................................................... 20 RS-422 .....................................................................................20 group master ........................................................................... 10 S Scene ........................................................................................11 46 DME8i-C/DME8o-C/DME4io-C Owner’s Manual  Foreword References secondary (backup) .................................................................. 19 Setting the IP address .............................................................. 23 [SIGNAL] Indicators .............................................................. 19 Introduction to the DME Satellite Signal Types ............................................................................ 12 Straight and Crossover Cable Wiring ...................................... 44 System Examples ..................................................................... 13 T Troubleshooting ...................................................................... 34 Controls and Connectors U unicast bundles ........................................................................ 16 USB Connection ..................................................................... 22 [USB] Connector .................................................................... 18 User Defined buttons (User Defined parameters) .................... 10 Connecting to a Computer W Warning Messages ................................................................... 39 Z References Other Functions Connecting to an External Device Audio I/O Connection zones ....................................................................................... 10 DME8i-C/DME8o-C/DME4io-C Owner’s Manual 47  Foreword Introduction to the DME Satellite Controls and Connectors Connecting to a Computer Audio I/O Connection Connecting to an External Device Other Functions References DME8i-C/DME8o-C/DME4io-C Owner’s Manual 48 MEMO  References Other Functions Connecting to an External Device Audio I/O Connection Connecting to a Computer Controls and Connectors Introduction to the DME Satellite Foreword MEMO DME8i-C/DME8o-C/DME4io-C Owner’s Manual 49  Foreword Introduction to the DME Satellite Controls and Connectors Connecting to a Computer Audio I/O Connection Connecting to an External Device Other Functions References DME8i-C/DME8o-C/DME4io-C Owner’s Manual 50 MEMO  For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante. NORTH AMERICA CANADA Yamaha Canada Music Ltd. 135 Milner Avenue, Scarborough, Ontario, M1S 3R1, Canada Tel: 416-298-1311 U.S.A. Yamaha Corporation of America 6600 Orangethorpe Ave., Buena Park, Calif. 90620, U.S.A. Tel: 714-522-9011 CENTRAL & SOUTH AMERICA MEXICO Yamaha de México S.A. de C.V. Calz. Javier Rojo Gómez #1149, Col. Guadalupe del Moral C.P. 09300, México, D.F., México Tel: 55-5804-0600 BRAZIL Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen Bestimmungsländern erhältlich. Para detalles sobre productos, contacte su tienda Yamaha más cercana o el distribuidor autorizado que se lista debajo. ASIA POLAND Yamaha Music Central Europe GmbH Sp.z. o.o. Oddzial w Polsce ul. 17 Stycznia 56, PL-02-146 Warszawa, Poland Tel: 022-868-07-57 THE NETHERLANDS/ BELGIUM/LUXEMBOURG Yamaha Music Central Europe GmbH, Branch Benelux Clarissenhof 5-b, 4133 AB Vianen, The Netherlands Tel: 0347-358 040 FRANCE Yamaha Musique France BP 70-77312 Marne-la-Vallée Cedex 2, France Tel: 01-64-61-4000 ITALY Yamaha Musica Italia S.P.A. Combo Division Viale Italia 88, 20020 Lainate (Milano), Italy Tel: 02-935-771 SPAIN/PORTUGAL Yamaha Musical do Brasil Ltda. Av. Reboucas 2636-Pinheiros CEP: 05402-400 Sao Paulo-SP. Brasil Tel: 011-3085-1377 ARGENTINA Yamaha-Hazen Música, S.A. Ctra. de la Coruna km. 17, 200, 28230 Las Rozas (Madrid), Spain Tel: 91-639-8888 SWEDEN Yamaha Music Latin America, S.A. Sucursal de Argentina Viamonte 1145 Piso2-B 1053, Buenos Aires, Argentina Tel: 1-4371-7021 PANAMA AND OTHER LATIN AMERICAN COUNTRIES/ CARIBBEAN COUNTRIES Yamaha Music Latin America, S.A. Torre Banco General, Piso 7, Urbanización Marbella, Calle 47 y Aquilino de la Guardia, Ciudad de Panamá, Panamá Tel: +507-269-5311 EUROPE THE UNITED KINGDOM Yamaha-Kemble Music (U.K.) Ltd. Sherbourne Drive, Tilbrook, Milton Keynes, MK7 8BL, England Tel: 01908-366700 GERMANY Yamaha Music Central Europe GmbH Siemensstraße 22-34, 25462 Rellingen, Germany Tel: 04101-3030 SWITZERLAND/LIECHTENSTEIN Yamaha Music Central Europe GmbH, Branch Switzerland Seefeldstrasse 94, 8008 Zürich, Switzerland Tel: 01-383 3990 AUSTRIA Yamaha Music Central Europe GmbH, Branch Austria Schleiergasse 20, A-1100 Wien, Austria Tel: 01-60203900 CZECH REPUBLIC/SLOVAKIA/ HUNGARY/SLOVENIA Yamaha Music Central Europe GmbH, Branch Austria, CEE Department Schleiergasse 20, A-1100 Wien, Austria Tel: 01-602039025 Yamaha Scandinavia AB J. A. Wettergrens Gata 1 Box 30053 S-400 43 Göteborg, Sweden Tel: 031 89 34 00 THE PEOPLE’S REPUBLIC OF CHINA Yamaha Music & Electronics (China) Co.,Ltd. 25/F., United Plaza, 1468 Nanjing Road (West), Jingan, Shanghai, China Tel: 021-6247-2211 INDONESIA PT. Yamaha Music Indonesia (Distributor) PT. Nusantik Gedung Yamaha Music Center, Jalan Jend. Gatot Subroto Kav. 4, Jakarta 12930, Indonesia Tel: 21-520-2577 KOREA Yamaha Music Korea Ltd. Tong-Yang Securities Bldg. 16F 23-8 Yoido-dong, Youngdungpo-ku, Seoul, Korea Tel: 02-3770-0660 MALAYSIA Yamaha Music Malaysia, Sdn., Bhd. Lot 8, Jalan Perbandaran, 47301 Kelana Jaya, Petaling Jaya, Selangor, Malaysia Tel: 3-78030900 SINGAPORE Yamaha Music Asia Pte., Ltd. #03-11 A-Z Building 140 Paya Lebor Road, Singapore 409015 Tel: 747-4374 TAIWAN Yamaha KHS Music Co., Ltd. 3F, #6, Sec.2, Nan Jing E. Rd. Taipei. Taiwan 104, R.O.C. Tel: 02-2511-8688 DENMARK YS Copenhagen Liaison Office Generatorvej 6A DK-2730 Herlev, Denmark Tel: 44 92 49 00 NORWAY Norsk filial av Yamaha Scandinavia AB Grini Næringspark 1 N-1345 Østerås, Norway Tel: 67 16 77 70 OTHER EUROPEAN COUNTRIES Yamaha Music Central Europe GmbH Siemensstraße 22-34, 25462 Rellingen, Germany Tel: +49-4101-3030 AFRICA Yamaha Corporation, Asia-Pacific Music Marketing Group Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650 Tel: +81-53-460-2313 MIDDLE EAST TURKEY/CYPRUS Yamaha Music Central Europe GmbH Siemensstraße 22-34, 25462 Rellingen, Germany Tel: 04101-3030 THAILAND Siam Music Yamaha Co., Ltd. 891/1 Siam Motors Building, 15-16 floor Rama 1 road, Wangmai, Pathumwan Bangkok 10330, Thailand Tel: 02-215-2626 OTHER ASIAN COUNTRIES Yamaha Corporation, Asia-Pacific Music Marketing Group Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650 Tel: +81-53-460-2317 OCEANIA AUSTRALIA Yamaha Music Australia Pty. Ltd. Level 1, 99 Queensbridge Street, Southbank, Victoria 3006, Australia Tel: 3-9693-5111 COUNTRIES AND TRUST TERRITORIES IN PACIFIC OCEAN Yamaha Corporation, Asia-Pacific Music Marketing Group Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650 Tel: +81-53-460-2313 OTHER COUNTRIES Yamaha Music Gulf FZE LB21-128 Jebel Ali Freezone P.O.Box 17328, Dubai, U.A.E. Tel: +971-4-881-5868 HEAD OFFICE Yamaha Corporation, Pro Audio & Digital Musical Instrument Division Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650 Tel: +81-53-460-2441 PA13  Yamaha Pro Audio global web site: http://www.yamahaproaudio.com/ Yamaha Manual Library http://www.yamaha.co.jp/manual/ This document is printed on chlorine free (ECF) paper with soy ink. U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation © 2006 Yamaha Corporation WG50630 606IPDHxx.x-xxA0 Printed in Japan