8
3.4 Pairing the Wireless subwoofer with the Soundbar
Ex faory the Wirele subwoofer and Soundbar are paired.
Automatic pairing
1 Plug the dedicated SoundMount power cable into the
Soundbar.
2 Plug the subwoofer into the mains sockets.
3 Pre the buon on the Soundbar or on the remote
control to switch the Soundbar ON.
> The subwoofer and soundbar will automatically pair
within 30 seconds.
> When the subwoofer is pairing with the soundbar, the
Indicator will flash rapidly.
> When the subwoofer is paired with the soundbar, the
Indicator will light up conantly.
> During ANDBY mode, the subwoofer Indicator will
go o and flash slowly.
Manual pairing
1 Plug the dedicated SoundMount power cable into the
Soundbar.
2 Plug the subwoofer into the mains sockets.
3 Make sure that the Soundbar is in ANDBY mode.
4 Pre and hold the Wirele pairing buon on the
boom of the subwoofer for a few seconds.
> The subwoofer will enter the pairing mode and the
Indicator will blink quickly.
5 Pre the buon on the Soundbar or on the remote
control to switch the Soundbar ON.
> Aer the wirele conneion succeeds, the Indicator
will light up conantly.
> If the Indicator ill blinks or does not blink at all, the
wirele conneion has failed.
• Unplug the cable of the subwoofer.
• Reconne the main cable aer 3 minutes.
• Repeat eps 1 - 5.
Notes!
• If the wirele conneion fails again, check if there is a
confli or rong interference (for example, interference
from an eleronic device) around your location.
Remove these conflis or rong interferences and
repeat the above procedures.
• The subwoofer mu be within 6m of the Soundbar in an
open area.
• If the Soundbar is not conneed with the subwoofer
and it is in On mode, then the meage
‘CHECK SUBWOOFER’ will show on the display and the
Indicator on the boom of the subwoofer will blink.
Repeat eps 1 - 5 above to pair the subwoofer to the
Soundbar.
4. GENERAL OPERATION
4.1 Using the remote control of the TV
When the HDMI ARC socket of the Soundbar is conneed
to the HDMI ARC socket of the TV via the HDMI cable and
the CEC funion on the TV is aivated in the setup menu of
the TV, you can use the remote control of the TV to
control the SoundMount (Soundbar and subwoofer).
• When the TV is switched ON, the SoundMount (Sound-
bar and subwoofer) will automatically switch ON.
• When the TV is switched to OFF / ANDBY, the Sound-
Mount will automatically switch OFF (to ANDBY).
• When the SoundMount is ON, the sound volume can be
controlled with the VOLUME - / VOLUME + and MUTE
buons on the remote control of the TV.
Note!
• To make it poible to control the SoundMount with the
remote control of the TV, it is important that the HDMI
CEC (Consumer Eleronics Control) funion is aivated
in the setup menu of the TV.
This funion has a dierent name for each TV brand:
Anynet (Samsung), Aquos Link (Sharp), Bravia Sync
(Sony), Regza Link (Toshiba), Simplink (LG),
Viera Link Panasonic), EZ-Sync (JVC), Easylink (Philips),
Netcommand (Mitsubishi).
The internal TV speakers will automatically be disabled
the moment the TV is switched ON and the Soundbar is
switched on automatically.
4.2 Using the supplied (Soundbar) remote control
When the HDMI ARC socket of the Soundbar is conneed
to the HDMI ARC socket of the TV via the HDMI cable and
the CEC funion on the TV is aivated in the setup menu of
the TV, you can use the remote control of the TV to
control the SoundMount (Soundbar and subwoofer).
In this case, you only need the supplid (Soundbar) remote
control for initial seings of personal preferences (TREBLE,
BASS, brightne level of Soundbar display) and for
controlling special funions like Bluetooth audio reaming.
In case the Soundbar and the TV are conneed via an
optical link, the supplied (Soundbar) remote control also
mu be used to control the SoundMount TV volume, source
seleion, etc..
It is not poible to control the sound volume with the
remote control of the TV. Internal TV speakers mu be
switched o manually. See the setup menu of the TV.
Standby / ON
When you fir conne the Soundbar to the mains socket,
the Soundbar will be in ANDBY mode and the ANDBY
Indicator lights red.
• Pre the buon on the Soundbar or on the remote
control of the TV to switch the Soundbar ON.
• Pre the buon again to switch the Soundbar back
to ANDBY mode.
> The Standby Indicator will light up red.
• Disconne the mains plug from the mains socket if you
want to switch the Soundbar o completely.
Note!
• When the Soundbar is idle for approximately 15 minutes,
it will automatically switch to ANDBY mode.