Pioneer DEH-150MP Handleiding

Categorie
Auto media-ontvangers
Type
Handleiding

Deze handleiding is ook geschikt voor

Black plate (1,1)
Owners Manual
Mode demploi
Manuale distruzioni
Manual de instrucciones
Bedienungsanleitung
Handleiding
Руководство пользователя
CD RDS RECEIVER
AUTORADIO CD RDS
SINTOLETTORE CD RDS
REPRODUCTOR DE CD CON RECEPTOR RDS
CD RDS-EMPFÄNGER
CD RDS-ONTVANGER
CD RDS ПРИЕМНИК
DEH-150MP
DEH-150MPG
English NederlandsDeutschEspañolItalianoFrançais Русский
Black plate (2,1)
Thank you for purchasing this PIONEER
product
To ensure proper use, please read through this
manual before using this product. It is especially
important that you read and observe WARN-
INGs and CAUTIONs in this manual. Please
keep the manual in a safe and accessible place for
future reference.
If you want to dispose this product, do not
mix it with general household waste. There is
a separate collection system for used elec-
tronic products in accordance with legislation
that requires proper treatment, recovery and
recycling.
Private households in the member states of the
EU, in Switzerland and Norway may return their
used electronic products free of charge to desig-
nated collection facilities or to a retailer (if you
purchase a similar new one).
For countries not mentioned above, please con-
tact your local authorities for the correct method
of disposal.
By doing so you will ensure that your disposed
product undergoes the necessary treatment, re-
covery and recycling and thus prevent potential
negative effects on the environment and human
health.
About this unit
The tuner frequencies on this unit are allocated
for use in Western Europe, Asia, the Middle
East, Africa and Oceania. Use in other areas
may result in poor reception. The RDS (radio
data system) function only operates in areas
with broadcasting RDS signals for FM stations.
CAUTION
This product is a class 1 laser product classi-
fied under the Safety of laser products, IEC
60825-1:2007.
CAUTION
! Do not allow this unit to come into contact
with liquids. Electrical shock could result.
Also, damage to this unit, smoke, and over-
heating could result from contact with
liquids.
! The Pioneer CarStereo-Pass is for use only in
Germany.
! Always keep the volume low enough to hear
outside sounds.
! Avoid exposure to moisture.
! If the battery is disconnected or discharged,
any preset memory will be erased.
Note
Function setting operations are completed even
if the menu is canceled before the operations
are confirmed.
In case of trouble
Should this unit fail to operate properly, please
contact your dealer or nearest authorized
PIONEER Service Station.
Head unit
b c
5
8
1 2 3 4 6
a9d7
Part Part
1 h (eject) 8 BAND
2 SRC/OFF 9
(back)/
DIMMER
(dimmer)
3
MULTI-CONTROL
(M.C.)
a c/d
4
(list) b 1/ to 6/
5 DISP c
AUX input jack
(3.5 mm stereo
jack)
6 Disc loading slot d Detach button
7
(equalizer)
Display indication
21 3 75
9
4 6 8
a
Indicator State
1
(list)
The list function is being oper-
ated.
2
Sub infor-
mation sec-
tion
Sub information is displayed.
3
TA (traffic
announce-
ments)
TA function is on.
4
TP (traffic
program
identifica-
tion)
A TP station is tuned in.
5
(sound re-
triever)
The sound retriever function
is on.
6 LOC Local seek tuning is on.
7
(repeat) Track or folder repeat is on.
8
(ran-
dom)
Random play is on.
9
Main infor-
mation sec-
tion
! Tuner: band and fre-
quency
! RDS: program service
name, PTY information
and other literal informa-
tion
! CD player: elapsed play-
back time and text infor-
mation
a
Appears when a lower tier of
folder or menu exists.
Set up menu
When you turn the ignition switch to ON after in-
stallation, set up menu appears on the display.
You can set up the menu options below.
Before you start
2
Section
Operating this unit
En
01
02
Black plate (3,1)
1 After installation of this unit, turn the
ignition switch to ON.
SET UP appears.
2 Turn M.C. to switch to YES.
# If you do not operate for 30 seconds, the set up
menu will not be displayed.
# If you prefer not to set up at this time, turn M.C.
to switch to NO. Press to select.
If you select NO, you cannot set up in the set up
menu.
3 Press M.C. to select.
4 Perform the following procedures to set
the menu.
To proceed to the next menu option, you need to
confirm your selection.
LANGUAGE (multi-language)
This unit can display the text information from a
compressed audio file even for information em-
bedded in English or Russian.
! If the embedded language and the selected
language setting are not the same, text infor-
mation may not display properly.
! Some characters may not be displayed prop-
erly.
1 Turn M.C. to select the desired setting.
ENG (English)РУС (Russian)
2 Press M.C. to confirm the selection.
CLOCK SET (setting the clock)
1 Turn M.C. to adjust hour.
2 Press M.C. to select minute.
3 Turn M.C. to adjust minute.
4 Press M.C. to confirm the selection.
FM STEP (FM tuning step)
Normally, the FM tuning step employed by seek
tuning is 50 kHz. When AF or TA is on, the tuning
step automatically changes to 100 kHz. It may be
preferable to set the tuning step to 50 kHz when
AF is on.
! The tuning step remains at 50 kHz during man-
ual tuning.
1 Turn M.C. to select the FM tuning step.
50 (50 kHz)100 (100 kHz)
2 Press M.C. to confirm the selection.
QUIT appears.
5 To finish your settings, turn M.C. to select
YES.
# If you prefer to change your setting again, turn
M.C. to switch to NO. Press to select.
6 Press M.C. to select.
Notes
! You can set up the menu options from the
system menu. For details about the settings,
refer to System menu on page 6.
! You can cancel set up menu by pressing
SRC/OFF.
Basic operations
Important
! Handle gently when removing or attaching
the front panel.
! Avoid subjecting the front panel to excessive
shock.
! Keep the front panel out of direct sunlight
and high temperatures.
! To avoid damaging the device or vehicle inte-
rior, remove any cables and devices attached
to the front panel before detaching it.
Removing the front panel to protect your unit from
theft
1 Press the detach button to release the front
panel.
2 Push the front panel upward (M) and then pull
it toward (N) you.
3 Always keep the detached front panel in a pro-
tection device such as a protection case.
Re-attaching the front panel
1 Slide the front panel to the left.
Make sure to insert the tabs on the left side of
the head unit into the slots on the front panel.
2 Press the right side of the front panel until it is
firmly seated.
If you cannot attach the front panel to the
head unit successfully, make sure that you are
placing the front panel onto the head unit cor-
rectly. Forcing the front panel into place may
result in damage to the front panel or head
unit.
Turning the unit on
1 Press SRC/OFF to turn the unit on.
Turning the unit off
1 Press and hold SRC/OFF until the unit turns
off.
Selecting a source
1 Press SRC/OFF to cycle between:
TUNER (tuner)CD (CD player)AUX (AUX)
Adjusting the volume
1 Turn M.C. to adjust the volume.
CAUTION
For safety reasons, park your vehicle when re-
moving the front panel.
Note
When this units blue/white lead is connected to
the vehicles auto-antenna relay control termi-
nal, the vehicles antenna extends when this
units source is turned on. To retract the anten-
na, turn the source off.
Frequently used menu
operations
Returning to the previous display
Returning to the previous list (the folder one level
higher)
1 Press
/DIMMER.
Returning to the ordinary display
Canceling the main menu
1 Press BAND.
Returning to the ordinary display from the list
1 Press BAND.
English
Operating this unit
3
Section
Operating this unit
En
02
Black plate (4,1)
Tuner
Basic operations
Selecting a band
1 Press BAND until the desired band (FM1,
FM2, FM3 for FM or MW/LW) is displayed.
Switching preset stations
1 Press c or d.
! Select PCH (preset channel) under SEEK to
use this function. For details about the set-
tings, refer to SEEK (left/right key setting) on
the next page.
Manual tuning (step by step)
1 Press c or d.
! Select MAN (manual tuning) under SEEK to
use this function. For details about the set-
tings, refer to SEEK (left/right key setting) on
the next page.
Seeking
1 Press and hold c or d, and then release.
You can cancel seek tuning by briefly pressing
c or d.
While pressing and holding c or d, you can
skip stations. Seek tuning starts as soon as
you release c or d.
Note
This units AF (alternative frequencies search)
function can be turned on and off. AF should be
off for normal tuning operation (refer to AF (al-
ternative frequencies search) on the next page).
Storing and recalling stations
for each band
Using preset tuning buttons
1 When you find a station that you want
to store in memory, press one of the preset
tuning buttons (1/
to 6/ ) and hold until
the preset number stops flashing.
2 Press one of the preset tuning buttons
(1/
to 6/ ) to select the desired station.
Switching the display
Selecting the desired text information
1 Press DISP to cycle between the following:
! FREQUENCY (program service name or
frequency)
! BRDCST INFO (program service name/PTY
information)
! CLOCK (source name and clock)
Notes
! If the program service name cannot be ac-
quired in FREQUENCY, the broadcast fre-
quency is displayed instead. If the program
service name is detected, the program serv-
ice name will be displayed.
! BRDCST INFO text information will change
automatically.
! Depending on the band, text information can
be changed.
! Text information items that can be changed
depend on the area.
Using PTY functions
You can tune in to a station using PTY (program
type) information.
Searching for an RDS station by PTY information
You can search for general types of broadcasting
programs, such as those listed in the following
section. Refer to this page.
1 Press
(list).
2 Turn M.C. to select a program type.
NEWS/INFOPOPULARCLASSICS
OTHERS
3 Press M.C. to begin the search.
The unit searches for a station broadcasting
that type of program. When a station is found,
its program service name is displayed.
! To cancel the search, press M.C. again.
! The program of some stations may differ
from that indicated by the transmitted PTY.
! If no station is broadcasting the type of
program you searched for, NOT FOUND is
displayed for about two seconds and then
the tuner returns to the original station.
PTY list
NEWS/INFO (news and information)
NEWS (News), AFFAIRS (Current affairs), INFO
(Information), SPORT (Sports), WEATHER (Weath-
er), FINANCE (Finance)
POPULAR (popular)
POP MUS (Popular music), ROCK MUS (Rock
music), EASY MUS (Easy listening), OTH MUS
(Other music), JAZZ (Jazz), COUNTRY (Country
music), NAT MUS (National music), OLDIES
(Oldies music), FOLK MUS (Folk music)
CLASSICS (classics)
L. CLASS (Light classical), CLASSIC (Classical)
OTHERS (others)
EDUCATE (Education), DRAMA (Drama), CUL-
TURE (Culture), SCIENCE (Science), VARIED (Var-
ied), CHILDREN (Childrens), SOCIAL (Social
affairs), RELIGION (Religion), PHONE IN (Phone
in), TOURING (Travel), LEISURE (Leisure), DOCU-
MENT (Documentaries)
Function settings
1 Press M.C. to display the main menu.
2 Turn M.C. to change the menu option
and press to select FUNCTION.
3 Turn M.C. to select the function.
Once selected, the following functions can be
adjusted.
# If MW/LW band is selected, only BSM, LOCAL
and SEEK are available.
BSM (best stations memory)
BSM (best stations memory) automatically stores
the six strongest stations in the order of their sig-
nal strength.
1 Press M.C. to turn BSM on.
To cancel, press M.C. again.
REGION (regional)
When AF is used, the regional function limits the
selection of stations to those broadcasting region-
al programs.
1 Press M.C. to turn the regional function on or
off.
LOCAL (local seek tuning)
Operating this unit
4
Section
Operating this unit
En
02
Black plate (5,1)
Local seek tuning lets you tune in to only those
radio stations with sufficiently strong signals for
good reception.
1 Press M.C. to select the desired setting.
FM: OFFLV1LV2LV3LV 4
MW/LW: OFFLV1 LV2
The highest level setting allows reception of
only the strongest stations, while lower levels
allow the reception of weaker stations.
TA (traffic announcement standby)
1 Press M.C. to turn traffic announcement
standby on or off.
AF (alternative frequencies search)
1 Press M.C. to turn AF on or off.
NEWS (news program interruption)
1 Press M.C. to turn the NEWS function on or
off.
SEEK (left/right key setting)
You can assign a function to the left and right keys
of the unit.
Select MAN (manual tuning) to tune up or down
manually or select PCH (preset channel) to switch
between preset channels.
1 Press M.C. to select MAN or PCH.
CD/CD-R/CD-RW
Basic operations
Playing a CD/CD-R/CD-RW
1 Insert the disc into the disc loading slot with
the label side up.
Ejecting a CD/CD-R/CD-RW
1 Press h.
Selecting a folder
1 Press 1/
or 2/ .
Selecting a track
1 Press c or d.
Fast forwarding or reversing
1 Press and hold c or d.
! When playing compressed audio, there is no
sound during fast forward or reverse.
Returning to root folder
1 Press and hold BAND.
Switching between compressed audio and CD-DA
1 Press BAND.
Switching the display
Selecting the desired text information
1 Press DISP to cycle between the following:
CD-DA
! ELAPSED TIME (track number and play-
back time)
! CLOCK (source name and clock)
! SPEANA (spectrum analyzer)
CD-TEXT
! TRACK INFO (track title/track artist/disc
title)
! ELAPSED TIME (track number and play-
back time)
! CLOCK (source name and clock)
! SPEANA (spectrum analyzer)
MP3/WMA/WAV
! TRACK INFO (track title/artist name/album
title)
! FILE INFO (file name/folder name)
! ELAPSED TIME (track number and play-
back time)
! CLOCK (source name and clock)
! SPEANA (spectrum analyzer)
Notes
! TRACK INFO and FILE INFO text information
will change automatically.
! Depending on the version of iTunes used to
write MP3 files to a disc or media file types,
incompatible text stored within an audio file
may be displayed incorrectly.
! Text information items that can be changed
depend on the media.
Selecting and playing files/
tracks from the name list
1 Press to switch to the file/track name
list mode.
2 Use M.C. to select the desired file name
(or folder name).
Selecting a file or folder
1 Turn M.C.
Playing
1 When a file or track is selected, press M.C.
Viewing a list of the files (or folders) in the se-
lected folder
1 When a folder is selected, press M.C.
Playing a song in the selected folder
1 When a folder is selected, press and hold M.C.
Operations using special buttons
Selecting a repeat play range
1 Press 6/
to cycle between the following:
! ALL Repeat all tracks
! ONE Repeat the current track
! FLD Repeat the current folder
Playing tracks in random order
1 Press 5/
to turn random play on or off.
Tracks in a selected repeat range are played in
random order.
! To change songs during random play, press d
to switch to the next track. Pressing c restarts
playback of the current track from the begin-
ning of the song.
Pausing playback
1 Press 4/PAUSE to pause or resume.
Enhancing compressed audio and restoring rich
sound (sound retriever)
1 Press 3/S.Rtrv to cycle between:
12OFF (off)
1 is effective for low compression rates, and 2
is effective for high compression rates.
Function settings
1 Press M.C. to display the main menu.
2 Turn M.C. to change the menu option
and press to select FUNCTION.
Once selected, the function below can be ad-
justed.
S.RTRV (sound retriever)
Automatically enhances compressed audio and
restores rich sound.
1 Press M.C. to select the desired setting.
For details, refer to Enhancing compressed
audio and restoring rich sound (sound retriever)
on this page.
Audio adjustments
1 Press M.C. to display the main menu.
2 Turn M.C. to change the menu option
and press to select AUDIO.
3 Turn M.C. to select the audio function.
Once selected, the following audio functions
can be adjusted.
! FADER is not available when SUB.W/SUB.W
is selected in SP-P/O MODE. For details, refer
to SP-P/O MODE (rear output and preout set-
ting) on page 7.
English
Operating this unit
5
Section
Operating this unit
En
02
Black plate (6,1)
! SUB.W, SUB.W CTRL and HPF SETTING are
not available when REAR/REAR is selected in
SP-P/O MODE. For details, refer to
SP-P/O MODE (rear output and preout set-
ting) on the next page.
! SUB.W CTRL and HPF SETTING are not avail-
able when SUB.W is selected in OFF. For de-
tails, refer to SUB.W (subwoofer on/off
setting) on this page.
FADER (fader adjustment)
1 Press M.C. to display the setting mode.
2 Turn M.C. to adjust the front/rear speaker bal-
ance.
BALANCE (balance adjustment)
1 Press M.C. to display the setting mode.
2 Turn M.C. to adjust the left/right speaker bal-
ance.
EQ SETTING (equalizer recall)
1 Press M.C. to display the setting mode.
2 Turn M.C. to select the equalizer.
POWERFULNATURALVOCALCUS-
TOM1CUSTOM2FLATSUPER BASS
The equalizer band and equalizer level can be
customized when CUSTOM1 or CUSTOM2 is
selected.
If selecting CUSTOM1 or CUSTOM2, complete
the procedures outlined below. If selecting
other options, press M.C. to return to the pre-
vious display.
! CUSTOM1 can be set separately for each
source.
! CUSTOM2 is a shared setting used in com-
mon for all sources.
3 Press M.C. to display the setting mode.
4 Press M.C. to cycle between the following:
Equalizer bandEqualizer level
5 Turn M.C. to select the desired setting.
Equalizer band: 80HZ250HZ800HZ
2.5KHZ8KHZ
Equalizer level: +6 to 6
! You can also switch the equalizer by pressing
repeatedly.
LOUDNESS (loudness)
Loudness compensates for deficiencies in the low-
frequency and high-frequency ranges at low vol-
ume.
1 Press M.C. to select the desired setting.
OFF (off)LOW (low)MID (mid)HI (high)
SUB.W (subwoofer on/off setting)
This unit is equipped with a subwoofer output
which can be turned on or off.
1 Press M.C. to select the desired setting.
NOR (normal phase)REV (reverse phase)
OFF (subwoofer off)
SUB.W CTRL (subwoofer adjustment)
Only frequencies lower than those in the selected
range are outputted from the subwoofer.
1 Press M.C. to display the setting mode.
2 Press M.C. to cycle between the following:
Cut-off frequencyOutput levelSlope level
Rates that can be adjusted will flash.
3 Turn M.C. to select the desired setting.
Cut-off frequency: 50HZ63HZ80HZ
100HZ125HZ160HZ200HZ
Output level: 24 to +6
Slope level: 6 12
BASS BOOST (bass boost)
1 Press M.C. to display the setting mode.
2 Turn M.C. to select a desired level.
0 to +6 is displayed as the level is increased or
decreased.
HPF SETTING (high pass filter adjustment)
When you do not want low sounds from the sub-
woofer output frequency range to play from the
front or rear speakers, turn on the HPF (high pass
filter). Only frequencies higher than those in the
selected range are output from the front or rear
speakers.
1 Press M.C. to display the setting mode.
2 Press M.C. to cycle between the following:
Cut-off frequencySlope level
3 Turn M.C. to select the desired setting.
Cut-off frequency: OFF50HZ63HZ80HZ
100HZ125HZ160HZ200HZ
Slope level: 6 12
SLA (source level adjustment)
SLA (Source level adjustment) lets you adjust the
volume level of each source to prevent radical
changes in volume when switching between sour-
ces.
! Settings are based on the FM volume level,
which remains unchanged.
! The MW/LW volume level can also be adjusted
with this function.
! When selecting FM as the source, you cannot
switch to SLA.
1 Press M.C. to display the setting mode.
2 Turn M.C. to adjust the source volume.
Adjustment range: +4 to 4
System menu
Important
PW SAVE (power saving) is canceled if the ve-
hicle battery is disconnected and will need to be
turned back on once the battery is reconnected.
When PW SAVE (power saving) is off, depend-
ing on connection methods, the unit may con-
tinue to draw power from the battery if your
vehicles ignition doesnt have an ACC (acces-
sory) position.
1 Press M.C. to display the main menu.
2 Turn M.C. to change the menu option
and press to select SYSTEM.
3 Turn M.C. to select the system menu
function.
Once selected, the following system menu func-
tions can be adjusted.
Operating this unit
6
Section
Operating this unit
En
02
Black plate (7,1)
LANGUAGE (multi-language)
This unit can display the text information from a
compressed audio file even for information em-
bedded in English or Russian.
! If the embedded language and the selected
language setting are not the same, text infor-
mation may not display properly.
! Some characters may not be displayed prop-
erly.
1 Turn M.C. to select the desired setting.
ENG (English)РУС (Russian)
CLOCK SET (setting the clock)
1 Press M.C. to display the setting mode.
2 Press M.C. to select the segment of the clock
display you wish to set.
HourMinute
3 Turn M.C. to adjust the clock.
12H/24H (time notation)
1 Press M.C. to select the desired setting.
12H (12-hour clock)24H (24-hour clock)
AUTO PI (auto PI seek)
The unit can automatically search for a different
station with the same programming, even during
preset recall.
1 Press M.C. to turn Auto PI seek on or off.
AUX (auxiliary input)
Activate this setting when using an auxiliar y de-
vice connected to this unit.
1 Press M.C. to turn AUX on or off.
MUTE MODE (mute mode)
Sound from this system is automatically muted or
attenuated when a signal from equipment with a
mute function is received.
1 Press M.C. to display the setting mode.
2 Turn M.C. to select the desired setting.
You can select any one of the options in the fol-
lowing list:
! MUTE Muting
! 20dB ATT Attenuation (20dB ATT has a
stronger effect than 10dB ATT)
! 10dB ATT Attenuation
PW SAVE (power saving)
Switching this function on enables you to reduce
the consumption of battery power.
! Turning on the source is the only operation al-
lowed when this function is on.
1 Press M.C. to turn the power save on or off.
Switching the dimmer setting
You can adjust the brightness of illumination.
1 Press M.C. to display the main menu.
2 Turn M.C. to display ILLUMI and press to
select.
3 Press M.C. to select the desired setting.
OFF (off)ON (on)
! You can also change the dimmer setting by
pressing and holding
/DIMMER.
Initial menu
1 Press and hold SRC/OFF until the unit
turns off.
2 Press and hold SRC/OFF until the main
menu appears in the display.
3 Turn M.C. to change the menu option
and press to select INITIAL.
4 Turn M.C. to select the initial menu func-
tion.
Once selected, the following initial menu func-
tions can be adjusted.
FM STEP (FM tuning step)
Normally, the FM tuning step employed by seek
tuning is 50 kHz. When AF or TA is on, the tuning
step automatically changes to 100 kHz. It may be
preferable to set the tuning step to 50 kHz when
AF is on.
! The tuning step remains at 50 kHz during man-
ual tuning.
1 Press M.C. to select the FM tuning step.
50 (50 kHz)100 (100 kHz)
SP-P/O MODE (rear output and preout setting)
The rear speaker leads output and the RCA output
of this unit can be used to connect a full-range
speaker or subwoofer. Select a suitable option for
your connection.
1 Press M.C. to display the setting mode.
2 Turn M.C. to select the desired setting.
You can select any one of the options in the fol-
lowing list:
! REAR/SUB.W Select when there is a full-
range speaker connected to the rear speak-
er leads output and there is a subwoofer
connected to the RCA output.
! SUB.W/SUB.W Select when there is a
subwoofer connected directly to the rear
speaker leads output without any auxiliary
amp and there is a subwoofer connected
to the RCA output.
! REAR/REAR Select when there is a full-
range speaker connected to the rear speak-
er leads output and the RCA output.
If there is a full-range speaker connected to
the rear speaker leads output and the RCA
output is not used, you may select either
REAR/SUB.W or REAR/REAR.
System menu
1 Press and hold SRC/OFF until the unit
turns off.
2 Press and hold SRC/OFF until the main
menu appears in the display.
3 Turn M.C. to change the menu option
and press to select SYSTEM.
4 Turn M.C. to select the system menu
function.
Once selected, the following system menu func-
tions can be adjusted.
English
Operating this unit
7
Section
Operating this unit
En
02
Black plate (8,1)
For details, refer to System menu on page 6.
Using an AUX source
1 Insert the stereo mini plug into the AUX
input jack.
2 Press SRC/OFF to select AUX as the
source.
Note
AUX cannot be selected unless the auxiliary set-
ting is turned on. For more details, refer to AUX
(auxiliary input) on the previous page.
Switching the display
Selecting the desired text information
1 Press DISP to cycle between the following:
! Source name
! Source name and clock
If an unwanted display appears
Turn off the unwanted display using the proce-
dures listed below.
1 Press M.C. to display the main menu.
2 Turn M.C. to change the menu option
and press to select SYSTEM.
3 Turn M.C. to display DEMO OFF and press
to select.
4 Turn M.C. to switch to YES.
5 Press M.C. to select.
Connections
Important
! When installing this unit in a vehicle without
an ACC (accessory) position on the ignition
switch, failure to connect the red cable to the
terminal that detects operation of the ignition
key may result in battery drain.
O
N
S
T
A
R
T
O
F
F
ACC position No ACC position
! Use of this unit in conditions other than the
following could result in fire or malfunction.
Vehicles with a 12-volt battery and negative
grounding.
Speakers with 50 W (output value) and 4 W to
8 W (impedance value).
! To prevent a short-circuit, overheating or mal-
function, be sure to follow the directions
below.
Disconnect the negative terminal of the bat-
tery before installation.
Secure the wiring with cable clamps or adhe-
sive tape. Wrap adhesive tape around wiring
that comes into contact with metal parts to
protect the wiring.
Place all cables away from moving parts,
such as the shift lever and seat rails.
Place all cables away from hot places, such
as near the heater outlet.
Do not connect the yellow cable to the battery
by passing it through the hole to the engine
compartment.
Cover any disconnected cable connectors
with insulating tape.
Do not shorten any cables.
Never cut the insulation of the power cable of
this unit in order to share the power with
other devices. The current capacity of the
cable is limited.
Use a fuse of the rating prescribed.
Never wire the negative speaker cable directly
to ground.
Never band together negative cables of multi-
ple speakers.
! When this unit is on, control signals are sent
through the blue/white cable. Connect this
cable to the system remote control of an ex-
ternal power amp or the vehicles auto-anten-
na relay control terminal (max. 300 mA
12 V DC). If the vehicle is equipped with a
glass antenna, connect it to the antenna
booster power supply terminal.
! Never connect the blue/white cable to the
power terminal of an external power amp.
Also, never connect it to the power terminal
of the auto antenna. Doing so may result in
battery drain or a malfunction.
! The black cable is ground. Ground cables for
this unit and other equipment (especially,
high-current products such as power amps)
must be wired separately. If they are not, an
accidental detachment may result in a fire or
malfunction.
This unit
3 45
21
1 Power cord input
2 Rear output or subwoofer output
3 Antenna input
4 Fuse (10 A)
5 Wired remote input
Hard-wired remote control adapter can be
connected (sold separately).
Operating this unit
8
Section
Installation
En
02
03
Black plate (9,1)
Power cord
1
3
3
2
4
4
5
5
6
6
b
8
9
7
a
e
d
c
1 To power cord input
2 Depending on the kind of vehicle, the func-
tion of 3 and 5 may be different. In this
case, be sure to connect 4 to 5 and 6 to
3.
3 Yellow
Back-up (or accessory)
4 Yellow
Connect to the constant 12 V supply termi-
nal.
5 Red
Accessory (or back-up)
6 Red
Connect to terminal controlled by ignition
switch (12 V DC).
7 Connect leads of the same color to each
other.
8 Black (chassis ground)
9 Blue/white
The pin position of the ISO connector will dif-
fer depending on the type of vehicle. Connect
9 and b when Pin 5 is an antenna control
type. In another type of vehicle, never con-
nect 9 and b.
a Blue/white
Connect to system control terminal of the
power amp (max. 300 mA 12 V DC).
b Blue/white
Connect to auto-antenna relay control termi-
nal (max. 300 mA 12 V DC).
c Yellow/black
If you use an equipment with Mute function,
wire this lead to the Audio Mute lead on that
equipment. If not, keep the Audio Mute lead
free of any connections.
d Speaker leads
White: Front left +
White/black: Front left *
Gray: Front right +
Gray/black: Front right *
Green: Rear left + or subwoofer +
Green/black: Rear left * or subwoofer *
Violet: Rear right + or subwoofer +
Violet/black: Rear right * or subwoofer *
e ISO connector
In some vehicles, the ISO connector may be
divided into two. In this case, be sure to con-
nect to both connectors.
Notes
! Change the initial menu of this unit. Refer to
SP-P/O MODE (rear output and preout set-
ting) on page 7.
The subwoofer output of this unit is monau-
ral.
! When using a subwoofer of 70 W (2 W), be
sure to connect the subwoofer to the violet
and violet/black leads of this unit. Do not
connect anything to the green and green/
black leads.
Power amp (sold separately)
Perform these connections when using the op-
tional amplifier.
1
3
2
4
55
1 System remote control
Connect to Blue/white cable.
2 Power amp (sold separately)
3 Connect with RCA cables (sold separately)
4 To Rear output or subwoofer output
5 Rear speaker or subwoofer
Installation
Important
! Check all connections and systems before
final installation.
! Do not use unauthorized parts as this may
cause malfunctions.
! Consult your dealer if installation requires
drilling of holes or other modifications to the
vehicle.
! Do not install this unit where:
it may interfere with operation of the vehicle.
it may cause injury to a passenger as a result
of a sudden stop.
! The semiconductor laser will be damaged if
it overheats. Install this unit away from hot
places such as near the heater outlet.
! Optimum performance is obtained when the
unit is installed at an angle of less than 60°.
60°
! When installing, to ensure proper heat dis-
persal when using this unit, make sure you
leave ample space behind the rear panel and
wrap any loose cables so they are not block-
ing the vents.
5cmcm
Leave ample
space
5 cm
5 cm
DIN front/rear mount
This unit can be properly installed using either
front-mount or rear-mount installation.
Use commercially available parts when instal-
ling.
DIN Front-mount
1 Insert the mounting sleeve into the dash-
board.
For installation in shallow spaces, use the sup-
plied mounting sleeve. If there is enough space,
use the mounting sleeve that came with the ve-
hicle.
2 Secure the mounting sleeve by using a
screwdriver to bend the metal tabs (90°) into
place.
1
2
1 Dashboard
English
Installation
9
Section
Installation
En
03
Black plate (10,1)
2 Mounting sleeve
# Make sure that the unit is installed securely in
place. An unstable installation may cause skipping
or other malfunctions.
DIN Rear-mount
1 Determine the appropriate position
where the holes on the bracket and the side
of the unit match.
2 Tighten two screws on each side.
1
2
3
1 Tapping screw (5 mm × 8 mm)
2 Mounting bracket
3 Dashboard or console
Removing the unit
1 Remove the trim ring.
1 Trim ring
2 Notched tab
! Releasing the front panel allows easier ac-
cess to the trim ring.
! When reattaching the trim ring, point the
side with the notched tab down.
2 Insert the supplied extraction keys into
both sides of the unit until they click into
place.
3 Pull the unit out of the dashboard.
Removing and re-attaching the front
panel
You can remove the front panel to protect your
unit from theft.
Press the detach button and push the front
panel upward and pull it toward you.
For details, refer to Removing the front panel to
protect your unit from theft and Re-attaching the
front panel on page 3.
Troubleshooting
Symptom Cause Action
The display
automatically
returns to the
ordinary dis-
play.
You did not per-
form any opera-
tion within
about 30 sec-
onds.
Perform operation
again.
The repeat
play range
changes un-
expectedly.
Depending on
the repeat play
range, the se-
lected range
may change
when another
folder or track is
being selected
or during fast
forwarding/re-
versing.
Select the repeat
play range again.
A subfolder is
not played
back.
Subfolders can-
not be played
when FLD (fold-
er repeat) is se-
lected.
Select another re-
peat play range.
NO XXXX ap-
pears when a
display is
changed (NO
TITLE, for ex-
ample).
There is no em-
bedded text in-
formation.
Switch the display
or play another
track/file.
The unit is
malfunction-
ing.
There is inter-
ference.
You are using a
device, such as
a cellular
phone, that
transmits elec-
tric waves near
the unit.
Move electrical
devices that may
be causing the in-
terference away
from the unit.
Error messages
When you contact your dealer or your nearest
Pioneer Service Center, be sure to note the error
message.
Common
Message Cause Action
AMP ERROR Unit fails to op-
erate or speaker
connection is
incorrect; pro-
tective circuit is
activated.
Check the speak-
er connection. If
the message fails
to disappear even
after the engine is
switched off/on,
contact your deal-
er or an author-
ized Pioneer
Service Station
for assistance.
CD player
Message Cause Action
ERROR-07,
11, 12, 17, 30
The disc is dirty. Clean the disc.
The disc is
scratched.
Replace the disc.
ERROR-07,
10, 11, 12,
15, 17, 30,
A0
There is an elec-
trical or me-
chanical error.
Turn the ignition
switch OFF and
back ON, or
switch to a differ-
ent source, then
back to the CD
player.
ERROR-15 The inserted
disc is blank.
Replace the disc.
ERROR-23 Unsupported
CD format.
Replace the disc.
Installation
10
Section
Additional information
En
03
Black plate (11,1)
Message Cause Action
FORMAT
READ
Sometimes
there is a delay
between the
start of playback
and when you
start to hear any
sound.
Wait until the
message disap-
pears and you
hear sound.
NO AUDIO The inserted
disc does not
contain any
playable files.
Replace the disc.
SKIPPED The inserted
disc contains
DRM protected
files.
Replace the disc.
PROTECT All the files on
the inserted
disc are em-
bedded with
DRM.
Replace the disc.
Handling guidelines
Discs and player
Use only discs that feature either of the following
two logos.
Use 12-cm discs. Do not use 8-cm discs or an
adapter for 8-cm discs.
Use only conventional, fully circular discs. Do not
use shaped discs.
Do not insert anything other than a CD into the
CD loading slot.
Do not use cracked, chipped, warped, or other-
wise damaged discs as they may damage the play-
er.
Unfinalized CD-R/RW discs cannot be played
back.
Do not touch the recorded surface of the discs.
Store discs in their cases when not in use.
Do not attach labels, write on or apply chemicals
to the surface of the discs.
To clean a CD, wipe the disc with a soft cloth out-
ward from the center.
Condensation may temporarily impair the players
performance. Let it rest for about one hour to ad-
just to a warmer temperature. Also, wipe any
damp discs off with a soft cloth.
Playback of discs may not be possible because of
disc characteristics, disc format, recorded applica-
tion, playback environment, storage conditions,
and so on.
Road shocks may interrupt disc playback.
Read the precautions for discs before using them.
When using discs that can be printed on label sur-
faces, check the instructions and the warnings of
the discs. Depending on the discs, inserting and
ejecting may not be possible. Using such discs
may result in damage to this equipment.
Do not attach commercially available labels or
other materials to the discs.
! The discs may warp making the disc unplay-
able.
! The labels may come off during playback and
prevent ejection of the discs, which may result
in damage to the equipment.
DualDiscs
DualDiscs are two-sided discs that have a record-
able CD for audio on one side and a recordable
DVD for video on the other.
Since the CD side of DualDiscs is not physically
compatible with the general CD standard, it may
not be possible to play the CD side with this unit.
Frequent loading and ejecting of a DualDisc may
result in scratches on the disc. Serious scratches
can lead to playback problems on this unit. In
some cases, a DualDisc may become stuck in the
disc loading slot and will not eject. To prevent this,
we recommend you refrain from using DualDisc
with this unit.
Please refer to the information from the disc man-
ufacturer for more detailed information about
DualDiscs.
Compressed audio
compatibility
WMA
File extension: .wma
Bit rate: 48 kbps to 320 kbps (CBR), 48 kbps to
384 kbps (VBR)
Sampling frequency: 32 kHz, 44.1 kHz, 48 kHz
Windows Media Audio Professional, Lossless,
Voice/DRM Stream/Stream with video: Not com-
patible
MP3
File extension: .mp3
Bit rate: 8 kbps to 320 kbps (CBR), VBR
Sampling frequency: 8 kHz to 48 kHz (32 kHz,
44.1 kHz, 48 kHz for emphasis)
Compatible ID3 tag version: 1.0, 1.1, 2.2, 2.3, 2.4
(ID3 tag Version 2.x is given priority over Version
1.x.)
M3u playlist: Not compatible
MP3i (MP3 interactive), mp3 PRO: Not compatible
WAV
File extension: .wav
Quantization bits: 8 and 16 (LPCM), 4 (MS
ADPCM)
Sampling frequency: 16 kHz to 48 kHz (LPCM),
22.05 kHz and 44.1 kHz (MS ADPCM)
English
Additional information
11
Appendix
Additional information
En
Black plate (12,1)
Supplemental information
Only the first 32 characters can be displayed as a
file name (including the file extension) or a folder
name.
Russian text to be displayed on this unit should be
encoded in one of the following character sets:
! Unicode (UTF-8, UTF-16)
! A character set other than Unicode that is
used in a Windows environment and is set to
Russian in the multi-language setting
This unit may not operate correctly depending on
the application used to encode WMA files.
Disc
Playable folder hierarchy: up to eight tiers (A prac-
tical hierarchy is less than two tiers.)
Playable folders: up to 99
Playable files: up to 999
File system: ISO 9660 Level 1 and 2, Romeo, Joliet
Multi-session playback: Compatible
Packet write data transfer: Not compatible
Regardless of the length of blank sections be-
tween the songs from the original recording, com-
pressed audio discs play with a short pause
between songs.
CAUTION
Do not leave discs in any place that is subject to
high temperatures.
Sequence of audio files
The user cannot assign folder numbers and
specify playback sequences with this unit.
Example of a hierarchy
Level 1 Level 2 Level 3 Level 4
01
02
03
04
05
: Folder
: Compressed
audio file
01 to 05: Folder
number
1 to 6: Playback
sequence
Disc
Folder selection sequence or other operation
may differ depending on the encoding or writing
software.
Russian character chart
D: C D: C D: C D: C D: C
: А : Б : В : Г : Д
: Е, Ё : Ж : З : И, Й : К
: Л : М : Н : О : П
: Р : С : Т : У : Ф
: Х : Ц : Ч
: Ш,
Щ
: Ъ
: Ы : Ь : Э : Ю : Я
D: Display C: Character
Copyright and trademark
iTunes
Apple and iTunes are trademarks of Apple Inc.,
registered in the U.S. and other countries.
MP3
Supply of this product only conveys a license for
private, non-commercial use and does not con-
vey a license nor imply any right to use this prod-
uct in any commercial (i.e. revenue-generating)
real time broadcasting (terrestrial, satellite,
cable and/or any other media), broadcasting/
streaming via internet, intranets and/or other
networks or in other electronic content distribu-
tion systems, such as pay-audio or audio-on-de-
mand applications. An independent license for
such use is required. For details, please visit
http://www.mp3licensing.com.
WMA
Windows Media is either a registered trademark
or trademark of Microsoft Corporation in the
United States and/or other countries.
This product includes technology owned by
Microsoft Corporation and cannot be used or
distributed without a license from Microsoft
Licensing, Inc.
Specifications
General
Power so urce ................... 14.4 V DC (10.8 V to 15.1 V al-
lowable)
Grounding system ............ Negative type
Maximum current consumption
................................... 10.0 A
Dimensions (W × H × D):
DIN
Chassis .............. 178mm × 50mm ×
165 mm
Nose .................. 188 mm × 58mm ×
16 mm
D
Chassis .............. 178mm × 50mm ×
165 mm
Nose .................. 170 mm × 46mm ×
16 mm
Weight ............................. 1 kg
Audio
Maximum power output ... 50 W × 4
70 W × 1/2 W (for subwoofer)
Continuous power output
................................... 22W × 4 (50Hz to 15000Hz,
5 % THD, 4 W load, both chan-
nels driven)
Load impedance .............. 4 W (4 W to 8 W allowable)
Preout maximum output level
................................... 2.0V
Loudness contour ............ +10dB (100 Hz), +6.5 dB
(10 kHz) (volume: 30 dB)
Equalizer (5-Band Graphic Equalizer):
Frequency ................. 80Hz/250 Hz/800 Hz/
2.5 kHz/8 kHz
Equalization range .... ±12 dB (2 dB step)
Subwoofer (mono):
Frequency ................. 50Hz/63 Hz/80 Hz/100 Hz/
125 Hz/160 Hz/200 Hz
Slope ........................ 6 dB/oct, 12 dB/oct
Gain ......................... +6dB to 24 dB
Phase ....................... Normal/Reverse
CD player
System ............................ Compact disc audio system
Usable discs .................... Compact disc
Signal-to-noise ra tio ......... 94dB (1 kHz) (IEC-A network)
Additional information
12
Appendix
Additional information
En
Black plate (13,1)
Number of channels ........ 2 (stereo)
MP3 decoding format ...... MPEG-1 & 2 Audio Layer 3
WMA decoding format ..... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2ch
audio)
(Windows Media Player)
WAV signal format ........... Linear PCM & MS ADPCM
(Non-compressed)
FM tuner
Frequency range .............. 87.5 MHz to 108.0 MHz
Usable sensitivity ............. 9dBf (0.8 µV/75 W, mono, S/N:
30 dB)
Signal-to-noise ra tio ......... 72dB (IEC-A network)
MW tuner
Frequency range .............. 531 kHz to 1602 kHz
Usable sensitivity ............. 25µV (S/N: 20 dB)
Signal-to-noise ra tio ......... 62dB (IEC-A network)
LW tuner
Frequency range .............. 153 kHz to 281kHz
Usable sensitivity ............. 28µV (S/N: 20 dB)
Signal-to-noise ra tio ......... 62dB (IEC-A network)
Note
Specifications and the design are subject to
modifications without notice.
English
Additional information
13
Appendix
En
Black plate (14,1)
Nous vous remercions davoir acheté cet ap-
pareil PIONEER.
Pour garantir une utilisation correcte, lisez bien
ce mode demploi avant dutiliser cet appareil. Il
est particulièrement important que vous lisiez et
respectiez les indications ATTENTION et PRÉ-
CAUTION de ce mode demploi. Conservez-le
dans un endroit sûr et facilement accessible pour
toute consultation ultérieure.
Si vous souhaitez vous débarrasser de cet ap-
pareil, ne le mettez pas à la poubelle avec vos
ordures ménagères. Il existe un système de
collecte séparé pour les appareils électroni-
ques usagés, qui doivent être récupérés, trai-
tés et recyclés conformément à la législation.
Dans les états membres de lUE, en Suisse et en
Norvège, les foyers domestiques peuvent rap-
porter leurs produits électroniques usagés gra-
tuitement à des points de collecte spécifiés ou à
un revendeur (sous réserve dachat dun produit
similaire).
Dans les pays qui ne sont pas mentionnés ci-
dessus, veuillez contacter les autorités locales
pour vous informer de la méthode correcte de
mise au rebut.
En agissant ainsi vous assurerez que le produit
que vous mettez au rebut est soumis au proces-
sus de traitement, de récupération et de recy-
clage nécessaire et éviterez ainsi les effets
négatifs potentiels sur lenvironnement et la
santé publique.
Quelques mots sur cet appareil
Les fréquences du syntoniseur de cet appareil
sont attribuées pour une utilisation en Europe
de lOuest, Asie, Moyen Orient, Afrique et Océ-
anie. Son utilisation dans dautres régions peut
se traduire par une réception de mauvaise qua-
lité. La fonction RDS (radio data system) nest
opérationnelle que dans les régions des si-
gnaux RDS sont diffusés pour les stations FM.
PRÉCAUTION
Cet appareil est un produit laser de Classe 1,
classé selon larticle IEC 60825-1:2007 relatif à
la Sécurité des produits laser.
APPAREIL À LASER DE CLASSE 1
PRÉCAUTION
! Ne laissez pas cet appareil entrer en contact
avec des liquides. Cela pourrait provoquer
une électrocution. Tout contact avec des li-
quides pourrait également provoquer des
dommages, de la fumée et une surchauffe
de lappareil.
! Le Pioneer CarStereo-Pass est utilisable seu-
lement en Allemagne.
! Maintenez le niveau découte à une valeur
telle que vous puissiez entendre les sons pro-
venant de lextérieur.
! Évitez tout contact avec lhumidité.
! Si la batterie est débranchée ou déchargée,
le contenu de la mémoire sera effacé.
Remarque
Les opérations de réglage des fonctions sont va-
lidées même si le menu est annulé avant la
confirmation des opérations.
En cas danomalie
En cas danomalie, veuillez contacter votre re-
vendeur ou le centre dentretien agréé par
PIONEER le plus proche.
Avant de commencer
14
Section
Avant de commencer
Fr
01
Black plate (15,1)
Appareil central
b c
5
8
1 2 3 4 6
a9d7
Partie Partie
1 h (éjection) 8 BAND
2 SRC/OFF 9
(retour)/DIM-
MER (atténuateur
de luminosité)
3
MULTI-CONTROL
(M.C.)
a c/d
4
(liste) b 1/ à 6/
5 DISP c
Jack dentrée
AUX (jack stéréo
3,5 mm)
6
Fente de charge-
ment des disques
d
Touche de retrait
de la face avant
7
(égaliseur)
Indications affichées
21 3 75
9
4 6 8
a
Indicateur État
1
(liste) La fonction liste est utilisée.
2
Section
dinforma-
tions secon-
daires
Les informations secondaires
sont affichées.
3
TA (bulle-
tins dinfor-
mations
routières)
La fonction TA est en service.
4
TP (identifi-
cation des
program-
mes dinfor-
mations
routières)
Lappareil est accordé sur une
station TP.
5
(sound re-
triever)
La fonction Sound Retriever
est activée.
6 LOC
Laccord automatique sur une
station locale est en service.
7
(répéti-
tion de la
lecture)
La fonction de répétition
dune plage ou dun dossier
est activée.
8
(lecture
aléatoire)
La lecture aléatoire est acti-
vée.
9
Section
dinforma-
tions princi-
pales
! Syntoniseur : gamme et
fréquence
! RDS : nom du service de
programme, informations
PTY et autres informations
textuelles
! Lecteur de CD : temps de
lecture écoulé et informa-
tions textuelles
a
Apparaît lorsquun niveau in-
férieur de dossier ou de menu
existe.
Menu de configuration
Lorsque vous mettez le contact dallumage sur
ON après linstallation, le menu de configura-
tion saffiche sur lécran.
Vous pouvez configurer les options de menu ci-
dessous.
1 Après avoir installé lappareil, mettez le
contact dallumage sur ON.
SET UP saffiche.
2 Tournez M.C. pour passer à YES.
# Si vous neffectuez aucune opération dans les
30 secondes environ, le menu de configuration ne
saffichera pas.
# Si vous préférez ne pas effectuer la configuration
pour linstant, tournez M.C. pour passer à NO. Ap-
puyez pour sélectionner.
Si vous sélectionnez NO, vous ne pouvez pas effec-
tuer de réglage dans le menu de configuration.
3 Appuyez sur M.C. pour sélectionner.
4 Effectuez les procédures suivantes pour
configurer le menu.
Pour passer à la prochaine option de menu,
vous devez confirmer votre sélection.
LANGUAGE (multilingue)
Cet appareil peut afficher les informations textuel-
les dun fichier audio compressé même si elles
sont incorporées en anglais ou en russe.
! Si la langue incorporée et la langue sélection-
née sont différentes, les informations textuel-
les peuvent ne pas safficher correctement.
! Certains caractères peuvent ne pas safficher
correctement.
1 Tournez M.C. pour sélectionner le réglage sou-
haité.
ENG (Anglais)РУС (Russe)
2 Appuyez sur M.C. pour confirmer la sélection.
CLOCK SET (réglage de lhorloge)
1 Tournez M.C. pour régler lheure.
2 Appuyez sur M.C. pour sélectionner les minu-
tes.
3 Tournez M.C. pour régler les minutes.
4 Appuyez sur M.C. pour confirmer la sélection.
FM STEP (incrément daccord FM)
Normalement, lincrément daccord FM employé
par laccord automatique est 50 kHz. Quand la
fonction AF ou TA est en service, lincrément dac-
cord passe automatiquement à 100 kHz. Il peut
être préférable de régler lincrément daccord à
50 kHz quand la fonction AF est en service.
! Pendant laccord manuel, lincrément dac-
cord est maintenu à 50 kHz.
1 Tournez M.C. pour choisir lincrément daccord
FM.
50 (50 kHz)100 (100 kHz)
2 Appuyez sur M.C. pour confirmer la sélection.
QUIT saffiche.
5 Pour terminer la configuration, tournez
M.C. pour sélectionner YES.
# Si vous souhaitez modifier à nouveau le réglage,
tournez M.C. pour passer à NO. Appuyez pour sélec-
tionner.
6 Appuyez sur M.C. pour sélectionner.
Remarques
! Vous pouvez configurer les options de menu
à partir du menu système. Pour des détails
sur les réglages, reportez-vous à la page 19,
Menu système.
! Vous pouvez annuler le menu de configura-
tion en appuyant sur SRC/OFF.
Opérations de base
Important
! Lorsque vous enlevez ou remontez la face
avant, manipulez-la doucement.
Français
Utilisation de lappareil
15
Section
Utilisation de lappareil
Fr
02
Black plate (16,1)
! Évitez de heurter la face avant.
! Conservez la face avant à labri des tempéra-
tures élevées et de la lumière directe du so-
leil.
! Pour éviter dendommager le périphérique
ou lintérieur du véhicule, retirez tous les câ-
bles et périphériques connectés à la face
avant, avant denlever cette dernière.
Retrait de la face avant pour protéger lappareil
contre le vol
1 Appuyez sur la touche de retrait pour libérer la
face avant.
2 Poussez la face avant vers le haut (M), puis
tirez-la vers vous (N).
3 Conservez toujours la face avant dans un boî-
tier de protection lorsquelle est détachée.
Remontage de la face avant
1 Faites glisser la face avant vers la gauche.
Assurez-vous dinsérer les encoches sur le
côté gauche de lappareil central dans les fen-
tes du panneau de commande.
2 Appuyez sur le côté droit de la face avant jus-
quàcequelle soit bien en place.
Si vous ne pouvez pas monter la face avant
sur lappareil central, vérifiez que la face avant
est correctement placée sur lappareil central.
Forcer la face avant en position risque de len-
dommager ou dendommager lappareil cen-
tral.
Mise en service de lappareil
1 Appuyez sur SRC/OFF pour mettre en service
lappareil.
Mise hors service de lappareil
1 Maintenez la pression sur SRC/OFF jusquàce
que lappareil soit mis hors tension.
Choix dune source
1 Appuyez sur SRC/OFF pour parcourir les op-
tions disponibles :
TUNER (syntoniseur)CD (lecteur de CD)
AUX (AUX)
Réglage du volume
1 Tournez M.C. pour régler le volume.
PRÉCAUTION
Pour des raisons de sécurité, garez votre véhi-
cule pour retirer la face avant.
Remarque
Si le fil bleu/blanc de lappareil est relié à la
prise de commande du relais de lantenne moto-
risée du véhicule, celle-ci se déploie lorsque la
source est mise en service. Pour rétracter lan-
tenne, mettez la source hors service.
Opérations de menu
fréquemment utilisées
Retour à laffichage précédent
Retour à la liste précédente (le dossier de niveau
immédiatement supérieur)
1 Appuyez sur
/DIMMER.
Retour à laffichage ordinaire
Annulation du menu principal
1 Appuyez sur BAND.
Retour à laffichage ordinaire à partir de la liste
1 Appuyez sur BAND.
Syntoniseur
Opérations de base
Sélection dune gamme
1 Appuyez sur BAND jusquà ce que la gamme
souhaitée, FM1, FM2, FM3 en FM ou MW/LW
(PO/GO), soit affichée.
Changement de fréquence en mémoire
1 Appuyez sur c ou d.
! Sélectionnez PCH (canal présélectionné) sous
SEEK pour utiliser cette fonction. Pour des dé-
tails sur les réglages, reportez-vous à la page
suivante, SEEK (réglage de la touche droite/gau-
che).
Accord manuel (pas à pas)
1 Appuyez sur c ou d.
! Sélectionnez MAN (accord manuel) sous
SEEK pour utiliser cette fonction. Pour des dé-
tails sur les réglages, reportez-vous à la page
suivante, SEEK (réglage de la touche droite/gau-
che).
Recherche
1 Appuyez de manière prolongée sur c ou d,
puis relâchez.
Vous pouvez annuler laccord automatique en
appuyant brièvement sur c ou d.
Lorsque vous appuyez de manière prolongée
sur c ou d, vous pouvez sauter des stations.
Laccord automatique démarre dès que vous
relâchez c ou d.
Remarque
La fonction AF (recherche des autres fréquences
possibles) de cet appareil peut être mise en ser-
vice ou hors service. La fonction AF doit être
hors service pendant une opération daccord
normal (reportez-vous à la page suivante, AF (re-
cherche des autres fréquences possibles)).
Enregistrement et rappel des
stations pour chaque gamme
Utilisation des touches de présélection
1 Lorsque se présente une station que vous
souhaitez mettre en mémoire, appuyez de
manière prolongée sur lune des touches de
présélection (1/
à6/ ) jusquà ce que le
numéro de la présélection cesse de clignoter.
2 Appuyez sur lune des touches de présé-
lection (1/
à6/ ) pour sélectionner la sta-
tion souhaitée.
Changement de laffichage
Sélection des informations textuelles souhaitées
1 Appuyez sur DISP pour parcourir les options
disponibles :
! FREQUENCY (nom du service de pro-
gramme ou fréquence)
! BRDCST INFO (nom du service de pro-
gramme/informations PTY)
! CLOCK (nom de la source et horloge)
Remarques
! Si le nom du service de programme ne peut
pas être acquis dans FREQUENCY, la fré-
quence démission saffiche alors. Si le nom
du service de programme est détecté, celui-
ci saffiche.
! Les informations textuelles BRDCST INFO
changent automatiquement.
! En fonction de la gamme sélectionnée, les
informations textuelles peuvent être différen-
tes.
! Les informations textuelles pouvant être mo-
difiées dépendent de la région.
Utilisation des fonctions PTY
Vous pouvez rechercher une station à laide de
son code PTY (type de programme).
Utilisation de lappareil
16
Section
Utilisation de lappareil
Fr
02
Black plate (17,1)
Recherche dune station RDS en utilisant le code
PTY
Vous pouvez rechercher une station qui diffuse un
type général de programme mentionné dans la
liste de la section suivante. Reportez-vous à cette
page.
1 Appuyez sur
(liste).
2 Tournez M.C. pour sélectionner le type de pro-
gramme.
NEWS/INFOPOPULARCLASSICS
OTHERS
3 Appuyez sur M.C. pour lancer la recherche.
Cet appareil recherche une station qui diffuse
ce type de programme. Quand une station est
trouvée, son nom de service de programme
est affiché.
! Appuyez à nouveau sur M.C. pour aban-
donner la recherche.
! Le type de lémission captée peut différer
de celui indiqué par le code PTY transmis.
! Si aucune station ne diffuse démission du
type choisi, lindication NOT FOUND saffi-
che pendant environ deux secondes puis
le syntoniseur saccorde sur la fréquence
dorigine.
Liste des codes PTY
NEWS/INFO (actualités et informations)
NEWS (Bulletin dinformations), AFFAIRS (Actuali-
tés), INFO (Informations), SPORT (Sports), WEA-
THER (Météo), FINANCE (Finance)
POPULAR (populaire)
POP MUS (Musique populaire), ROCK MUS
(Rock), EASY MUS (Musique légère), OTH MUS
(Autre musique), JAZZ (Jazz), COUNTRY (Coun-
try), NAT MUS (Musique nationale), OLDIES (Mu-
sique du bon vieux temps), FOLK MUS (Folk)
CLASSICS (classique)
L. CLASS (Musique classique légère), CLASSIC
(Musique classique)
OTHERS (autres)
EDUCATE (Éducation), DRAMA (Drame),
CULTURE (Culture), SCIENCE (Science), VARIED
(Programmes variés), CHILDREN (Émissions desti-
nées aux enfants), SOCIAL (Sujets de société), RE-
LIGION (Religion), PHONE IN (Programmes à
ligne ouverte), TOURING (Voyages), LEISURE (Loi-
sirs), DOCUMENT (Documentaires)
Réglages des fonctions
1 Appuyez sur M.C. pour afficher le menu
principal.
2 Tournez M.C. pour changer loption de
menu et appuyez pour sélectionner
FUNCTION.
3 Tournez M.C. pour sélectionner la fonc-
tion.
Une fois sélectionnées, les fonctions suivantes
peuvent être ajustées.
# Si la gamme MW/LW (PO/GO) est sélectionnée,
seuls BSM, LOCAL et SEEK sont disponibles.
BSM (mémoire des meilleures stations)
La fonction BSM (mémoire des meilleures sta-
tions) mémorise automatiquement les six stations
les plus fortes dans lordre de la force du signal.
1 Appuyez sur M.C. pour mettre la fonction BSM
en service.
Pour annuler, appuyez à nouveau sur M.C.
REGION (stations régionales)
Quand la fonction AF est utilisée, la fonction de re-
cherche des stations régionales limite la sélection
aux stations qui diffusent des programmes régio-
naux.
1 Appuyez sur M.C. pour mettre la fonction de
recherche des stations régionales en service
ou hors service.
LOCAL (accord automatique sur une station lo-
cale)
Laccord automatique sur une station locale ne
sintéresse quaux stations de radio dont le signal
reçu est suffisamment puissant pour garantir une
réception de bonne qualité.
1 Appuyez sur M.C. pour sélectionner le réglage
souhaité.
FM : OFFLV1LV2LV3LV 4
MW/LW (PO/GO) : OFFLV1LV2
La valeur la plus élevée permet la réception
des seules stations très puissantes ; les autres
valeurs autorisent la réception de stations
moins puissantes.
TA (attente de bulletins dinformations routières)
1 Appuyez sur M.C. pour mettre en service ou
hors service lattente dun bulletin dinforma-
tions routières.
AF (recherche des autres fréquences possibles)
1 Appuyez sur M.C. pour mettre la fonction AF
en service ou hors service.
NEWS (interruption pour réception dun bulletin
dinformations)
1 Appuyez sur M.C. pour mettre la fonction
NEWS (bulletin dinformations) en service ou
hors service.
SEEK (réglage de la touche droite/gauche)
Vous pouvez assigner une fonction aux touches
droite et gauche de lappareil.
Sélectionnez MAN (accord manuel) pour effectuer
un accord de fréquence manuellement ou sélec-
tionnez PCH (canaux présélectionnés) pour chan-
ger de canal présélectionné.
1 Appuyez sur M.C. pour sélectionner MAN ou
PCH.
CD/CD-R/CD-RW
Opérations de base
Lecture dun CD/CD-R/CD-RW
1 Introduisez un disque, létiquette vers le haut,
dans le logement de chargement des disques.
Éjection dun CD/CD-R/CD-RW
1 Appuyez sur h.
Sélection dun dossier
1 Appuyez sur 1/
ou 2/ .
Sélection dune plage
1 Appuyez sur c ou d.
Avance ou retour rapide
1 Appuyez de manière prolongée sur c ou d.
! Lors de la lecture dun disque daudio
compressé, aucun son nest émis pendant la-
vance ou le retour rapide.
Retour au dossier racine
1 Appuyez sur BAND de façon prolongée.
Commutation entre les modes audio compressé
et CD-DA
1 Appuyez sur BAND.
Français
Utilisation de lappareil
17
Section
Utilisation de lappareil
Fr
02
Black plate (18,1)
Changement de laffichage
Sélection des informations textuelles souhaitées
1 Appuyez sur DISP pour parcourir les options
disponibles :
CD-DA
! ELAPSED TIME (numéro de plage et temps
de lecture)
! CLOCK (nom de la source et horloge)
! SPEANA (analyseur de spectre)
CD-TEXT
! TRACK INFO (titre de la plage/interprète
de la plage/titre du disque)
! ELAPSED TIME (numéro de plage et temps
de lecture)
! CLOCK (nom de la source et horloge)
! SPEANA (analyseur de spectre)
MP3/WMA/WAV
! TRACK INFO (titre de la plage/nom de lin-
terprète/nom de lalbum)
! FILE INFO (nom du fichier/nom du dossier)
! ELAPSED TIME (numéro de plage et temps
de lecture)
! CLOCK (nom de la source et horloge)
! SPEANA (analyseur de spectre)
Remarques
! Les informations textuelles TRACK INFO et
FILE INFO changent automatiquement.
! Selon la version de iTunes utilisée pour enre-
gistrer les fichiers MP3 sur un disque ou les
types de fichiers média, des informations tex-
tuelles incompatibles enregistrées dans le fi-
chier audio peuvent ne pas safficher
correctement.
! Les informations textuelles pouvant être mo-
difiées dépendent du média.
Sélection et lecture des fichiers/
plages à partir de la liste des noms
1 Appuyez sur pour passer en mode
liste des noms de fichiers/plages.
2 Utilisez M.C. pour sélectionner le nom de
fichier (ou nom de dossier) souhaité.
Sélection dun fichier ou dun dossier
1 Tournez M.C.
Lecture
1 Lorsquun fichier ou une plage est sélection-
né(e), appuyez sur M.C.
Affichage dune liste des fichiers (ou des dossiers)
dans le dossier sélectionné
1 Quand un dossier est sélectionné, appuyez sur
M.C.
Lecture dune plage musicale dans le dossier sé-
lectionné
1 Quand un dossier est sélectionné, appuyez de
manière prolongée sur M.C.
Opérations à laide de touches
spéciales
Sélection dune étendue de répétition de lecture
1 Appuyez sur 6/
pour parcourir les options
disponibles :
! ALL Répétition de toutes les plages
! ONE Répétition de la plage en cours de
lecture
! FLD Répétition du dossier en cours de
lecture
Lecture des plages dans un ordre aléatoire
1 Appuyez sur 5/
pour activer ou désactiver
la lecture aléatoire.
Les plages dune étendue de répétition sélec-
tionnée sont lues dans un ordre aléatoire.
! Pour changer de plage musicale pendant une
lecture aléatoire, appuyez sur d pour passer à
la plage suivante. Appuyez sur c pour redé-
marrer la lecture de la plage en cours au
début de la plage musicale.
Pause de la lecture
1 Appuyez sur 4/PAUSE pour mettre en pause
ou reprendre la lecture.
Amélioration de laudio compressé et restauration
dun son riche (sound retriever (correcteur de son
compressé))
1 Appuyez sur 3/S.Rtrv pour parcourir les op-
tions disponibles :
12OFF (hors service)
1 est efficace pour les faibles taux de compres-
sion et 2 est efficace pour les taux de compres-
sion élevés.
Réglages des fonctions
1 Appuyez sur M.C. pour afficher le menu
principal.
2 Tournez M.C. pour changer loption de
menu et appuyez pour sélectionner
FUNCTION.
Une fois sélectionnée, la fonction ci-dessous
peut être ajustée.
S.RTRV (sound retriever)
Améliore automatiquement laudio compressé et
restaure un son riche.
1 Appuyez sur M.C. pour sélectionner le réglage
souhaité.
Pour les détails, reportez-vous à cette page,
Amélioration de laudio compressé et restaura-
tion dun son riche (sound retriever (correcteur
de son compressé)).
Réglages sonores
1 Appuyez sur M.C. pour afficher le menu
principal.
2 Tournez M.C. pour changer loption de
menu et appuyez pour sélectionner AUDIO.
3 Tournez M.C. pour sélectionner la fonc-
tion audio.
Une fois sélectionnées, les fonctions audio sui-
vantes peuvent être ajustées.
! FADER nest pas disponible lorsque
SUB.W/SUB.W est sélectionné dans
SP-P/O MODE. Pour les détails, reportez-vous
à la page 20, SP-P/O MODE (réglage de la sor-
tie arrière et du préamp).
! SUB.W, SUB.W CTRL et HPF SETTING ne
sont pas disponibles lorsque REAR/REAR est
sélectionné dans SP-P/O MODE. Pour les dé-
tails, reportez-vous à la page 20,
SP-P/O MODE (réglage de la sortie arrière et
du préamp).
! SUB.W CTRL et HPF SETTING ne sont pas
disponibles lorsque SUB.W est sélectionné
dans OFF. Pour les détails, reportez-vous à la
page suivante, SUB.W (réglage en service/
hors service du haut-parleur dextrêmes gra-
ves).
FADER (réglage de léquilibre avant-arrière)
1 Appuyez sur M.C. pour afficher le mode de ré-
glage.
2 Tournez M.C. pour régler léquilibre sonore
entre les haut-parleurs avant et arrière.
BALANCE (réglage déquilibre sonore)
1 Appuyez sur M.C. pour afficher le mode de ré-
glage.
2 Tournez M.C. pour régler léquilibre sonore
entre les haut-parleurs gauche/droite.
EQ SETTING (rappel de légaliseur)
Utilisation de lappareil
18
Section
Utilisation de lappareil
Fr
02
Black plate (19,1)
1 Appuyez sur M.C. pour afficher le mode de ré-
glage.
2 Tournez M.C. pour sélectionner légaliseur.
POWERFULNATURALVOCALCUS-
TOM1CUSTOM2FLATSUPER BASS
La bande et le niveau de légalisateur peuvent
être personnalisés lorsque CUSTOM1 ou CUS-
TOM2 est sélectionné.
Si CUSTOM1 ou CUSTOM2 est sélectionné,
suivez les procédures décrites ci-dessous. Si
dautres options sont sélectionnées, appuyez
sur M.C. pour revenir à laffichage précédent.
! CUSTOM1 peut être réglé séparément
pour chaque source.
! CUSTOM2 est un réglage partagé et
commun à toutes les sources.
3 Appuyez sur M.C. pour afficher le mode de ré-
glage.
4 Appuyez sur M.C. pour parcourir les options
disponibles :
Bande de légaliseurNiveau de légaliseur
5 Tournez M.C. pour sélectionner le réglage sou-
haité.
Bande de légaliseur : 80HZ250HZ800HZ
2.5KHZ8KHZ
Niveau de légaliseur : +6 à 6
! Vous pouvez également changer légaliseur en
appuyant de manière répétée sur
.
LOUDNESS (correction physiologique)
La correction physiologique a pour objet daccen-
tuer les hautes et les basses fréquences à bas ni-
veaux découte.
1 Appuyez sur M.C. pour sélectionner le réglage
souhaité.
OFF (hors service)LOW (faible)MID
(moyen)HI (élevé)
SUB.W (réglage en service/hors service du haut-
parleur dextrêmes graves)
Cet appareil est équipé dune sortie haut-parleur
dextrêmes graves qui peut être mise en service
ou hors service.
1 Appuyez sur M.C. pour sélectionner le réglage
souhaité.
NOR (phase normale) REV (phase inversée)
OFF (haut-parleur dextrêmes graves désac-
tivé)
SUB.W CTRL (réglage du haut-parleur dextrêmes
graves)
Seules les fréquences inférieures à celles de la
plage sélectionnée sont produites par le haut-par-
leur dextrêmes graves.
1 Appuyez sur M.C. pour afficher le mode de ré-
glage.
2 Appuyez sur M.C. pour parcourir les options
disponibles :
Fréquence de coupureNiveau de sortieNi-
veau de pente
Les débits pouvant être réglés clignotent.
3 Tournez M.C. pour sélectionner le réglage sou-
haité.
Fréquence de coupure : 50HZ63HZ80HZ
100HZ125HZ160HZ200HZ
Niveau de sortie : 24 à +6
Niveau de pente : 6 12
BASS BOOST (accentuation des graves)
1 Appuyez sur M.C. pour afficher le mode de ré-
glage.
2 Tournez M.C. pour sélectionner le niveau dé-
siré.
0 à +6 sont les valeurs affichées tandis que le
niveau augmente ou diminue.
HPF SETTING (réglage du filtre passe-haut)
Quand vous ne voulez pas que les sons graves de
la gamme de fréquence de la sortie haut-parleur
dextrêmes graves soient émis par les haut-par-
leurs avant ou arrière, mettez le filtre passe-haut
(HPF) en service. Seules les fréquences supérieu-
res à celles de la plage sélectionnée sont émises
par les haut-parleurs avant ou arrière.
1 Appuyez sur M.C. pour afficher le mode de ré-
glage.
2 Appuyez sur M.C. pour parcourir les options
disponibles :
Fréquence de coupureNiveau de pente
3 Tournez M.C. pour sélectionner le réglage sou-
haité.
Fréquence de coupure : OFF50HZ63HZ
80HZ100HZ125HZ160HZ200HZ
Niveau de pente : 6 12
SLA (réglage du niveau de la source)
La fonction SLA (réglage du niveau de la source)
permet dajuster les niveaux sonores de chaque
source afin déviter que ne se produisent de fortes
variations damplitude sonore lorsque vous passez
dune source à lautre.
! Les réglages sont basés sur le niveau du vo-
lume FM qui lui, demeure inchangé.
! Le niveau du volume MW/LW (PO/GO) peut
également être réglé avec cette fonction.
! Si FM a été choisie comme source, vous ne
pouvez pas afficher la fonction SLA.
1 Appuyez sur M.C. pour afficher le mode de ré-
glage.
2 Tournez M.C. pour régler le volume de la
source.
Plage de réglage : +4 à 4
Menu système
Important
La fonction PW SAVE (économie dénergie) est
annulée si la batterie du véhicule est déconnec-
tée et devra être réactivée une fois la batterie re-
connectée. Quand PW SAVE est hors service, il
est possible que selon la méthode de connexion
utilisée lappareil continue à consommer du
courant de la batterie si le commutateur de
contact de votre véhicule ne possède pas de po-
sition ACC (accessoire).
1 Appuyez sur M.C. pour afficher le menu
principal.
2 Tournez M.C. pour changer loption de
menu et appuyez pour sélectionner SYSTEM.
3 Tournez M.C. pour sélectionner la fonc-
tion du menu système.
Une fois sélectionnées, les fonctions du menu
système suivantes peuvent être ajustées.
LANGUAGE (multilingue)
Cet appareil peut afficher les informations textuel-
les dun fichier audio compressé même si elles
sont incorporées en anglais ou en russe.
! Si la langue incorporée et la langue sélection-
née sont différentes, les informations textuel-
les peuvent ne pas safficher correctement.
! Certains caractères peuvent ne pas safficher
correctement.
1 Tournez M.C. pour sélectionner le réglage sou-
haité.
ENG (Anglais)РУС (Russe)
CLOCK SET (réglage de lhorloge)
Français
Utilisation de lappareil
19
Section
Utilisation de lappareil
Fr
02
Black plate (20,1)
1 Appuyez sur M.C. pour afficher le mode de ré-
glage.
2 Appuyez sur M.C. pour sélectionner le seg-
ment de laffichage de lhorloge que vous sou-
haitez régler.
HeureMinute
3 Tournez M.C. pour régler lhorloge.
12H/24H (notation temporelle)
1 Appuyez sur M.C. pour sélectionner le réglage
souhaité.
12H (horloge 12 heures)24H (horloge
24 heures)
AUTO PI (recherche automatique PI)
Lappareil peut rechercher automatiquement une
autre station avec le même type de programme, y
compris si laccord a été obtenu par le rappel
dune fréquence en mémoire.
1 Appuyez sur M.C. pour mettre en service ou
hors service la recherche automatique PI.
AUX (entrée auxiliaire)
Activez ce réglage lorsque vous utilisez un appa-
reil auxiliaire connecté à cet appareil.
1 Appuyez sur M.C. pour mettre AUX en service
ou hors service.
MUTE MODE (mode sourdine)
Le son émis par lappareil est automatiquement
coupé ou atténué quand un signal en provenance
dun équipement possédant la fonction silencieux
est reçu.
1 Appuyez sur M.C. pour afficher le mode de ré-
glage.
2 Tournez M.C. pour sélectionner le réglage sou-
haité.
Vous pouvez sélectionner lune des options de
la liste suivante :
! MUTE Silencieux
! 20dB ATT Atténuation (20dB ATT aun
effet plus fort que 10dB ATT)
! 10dB ATT Atténuation
PW SAVE (économie dénergie)
Activer cette fonction vous permet de réduire la
consommation de la batterie.
! La mise en service de la source est la seule
opération permise quand cette fonction est en
service.
1 Appuyez sur M.C. pour mettre léconomie dé-
nergie en service ou hors service.
Mise en service ou hors service
de latténuateur de luminosité
Vous pouvez régler la luminosité déclairage.
1 Appuyez sur M.C. pour afficher le menu
principal.
2 Tournez M.C. pour afficher ILLUMI, puis
appuyez pour sélectionner.
3 Appuyez sur M.C. pour sélectionner le ré-
glage souhaité.
OFF (hors service)ON (en service)
! Vous pouvez également changer le réglage
de latténuateur de luminosité en appuyant
de façon prolongée sur
/DIMMER.
Menu initial
1 Maintenez la pression sur SRC/OFF jus-
quà ce que lappareil soit mis hors tension.
2 Appuyez de façon prolongée sur SRC/
OFF jusquà ce que le menu principal appa-
raisse sur lafficheur.
3 Tournez M.C. pour changer loption de
menu et appuyez pour sélectionner INITIAL.
4 Tournez M.C. pour sélectionner la fonc-
tion du menu initial.
Une fois sélectionnées, les fonctions du menu
initial suivantes peuvent être ajustées.
FM STEP (incrément daccord FM)
Normalement, lincrément daccord FM employé
par laccord automatique est 50 kHz. Quand la
fonction AF ou TA est en service, lincrément dac-
cord passe automatiquement à 100 kHz. Il peut
être préférable de régler lincrément daccord à
50 kHz quand la fonction AF est en service.
! Pendant laccord manuel, lincrément dac-
cord est maintenu à 50 kHz.
1 Appuyez sur M.C. pour choisir lincrément
daccord FM.
50 (50 kHz)100 (100 kHz)
SP-P/O MODE (réglage de la sortie arrière et du
préamp)
La sortie des bornes du haut-parleur arrière et la
sortie RCA de cet appareil peuvent être utilisées
pour connecter un haut-parleur pleine gamme ou
un haut-parleur dextrêmes graves. Sélectionnez
loption appropriée à votre connexion.
1 Appuyez sur M.C. pour afficher le mode de ré-
glage.
2 Tournez M.C. pour sélectionner le réglage sou-
haité.
Vous pouvez sélectionner lune des options de
la liste suivante :
! REAR/SUB.W Sélectionnez cette option
lorsquun haut-parleur pleine gamme est
connecté aux bornes du haut-parleur ar-
rière et quun haut-parleur dextrêmes gra-
ves est connecté à la sortie RCA.
! SUB.W/SUB.W Sélectionnez cette option
lorsquun haut-parleur dextrêmes graves
est connecté directement aux bornes du
haut-parleur arrière sans amplificateur au-
xiliaire et quun haut-parleur dextrêmes
graves est connecté à la sortie RCA.
! REAR/REAR Sélectionnez cette option
lorsquun haut-parleur pleine gamme est
connecté aux bornes du haut-parleur ar-
rière et à la sortie RCA.
Si un haut-parleur pleine gamme est
connecté à la sortie des bornes du haut-
parleur arrière et que la sortie RCA nest
pas utilisée, vous pouvez sélectionner
REAR/SUB.W ou REAR/REAR.
Menu système
1 Maintenez la pression sur SRC/OFF jus-
quà ce que lappareil soit mis hors tension.
2 Appuyez de façon prolongée sur SRC/
OFF jusquà ce que le menu principal appa-
raisse sur lafficheur.
Utilisation de lappareil
20
Section
Utilisation de lappareil
Fr
02
Black plate (21,1)
3 Tournez M.C. pour changer loption de
menu et appuyez pour sélectionner SYSTEM.
4 Tournez M.C. pour sélectionner la fonc-
tion du menu système.
Une fois sélectionnées, les fonctions du menu
système suivantes peuvent être ajustées.
Pour les détails, reportez-vous à la page 19,
Menu système.
Utilisation dune source AUX
1 Insérez la mini prise stéréo dans le jack
dentrée AUX.
2 Appuyez sur SRC/OFF pour choisir AUX
comme source.
Remarque
Vous ne pouvez pas sélectionner AUX à moins
que le réglage auxiliaire soit activé. Pour plus de
détails, reportez-vous à la page précédente,
AUX (entrée auxiliaire).
Changement de laffichage
Sélection des informations textuelles souhaitées
1 Appuyez sur DISP pour parcourir les options
disponibles :
! Nom de la source
! Nom de la source et horloge
Si un écran non souhaité
saffiche
Mettez lécran non souhaité hors ser vice à laide
des procédures répertoriées ci-dessous.
1 Appuyez sur M.C. pour afficher le menu
principal.
2 Tournez M.C. pour changer loption de
menu et appuyez pour sélectionner SYSTEM.
3 Tournez M.C. pour afficher DEMO OFF,
puis appuyez pour sélectionner.
4 Tournez M.C. pour passer à YES.
5 Appuyez sur M.C. pour sélectionner.
Connexions
Important
! Lors de linstallation de cet appareil dans un
véhicule sans position ACC (accessoire) sur
le contact dallumage, ne pas connecter le
câble rouge à la borne qui détecte lutilisa-
tion de la clé de contact peut entraîner le dé-
chargement de la batterie.
O
N
S
T
A
R
T
O
F
F
Avec position ACC Sans position ACC
! Lutilisation de cet appareil dans des condi-
tions autres que les conditions suivantes
pourrait provoquer un incendie ou un mau-
vais fonctionnement.
Véhicules avec une batterie 12 volts et mise à
la masse du négatif.
Haut-parleurs avec une puissance de sortie
de 50 W et une impédance de 4 W à8W.
! Pour éviter un court-circuit, une surchauffe
ou un dysfonctionnement, assurez-vous de
respecter les instructions suivantes.
Déconnectez la borne négative de la batterie
avant linstallation.
Fixez le câblage avec des serre-fils ou de la
bande adhésive. Pour protéger le câblage, en-
roulez dans du ruban adhésif les parties du
câblage en contact avec des pièces en métal.
Placez les câbles à lécart de toutes les par-
ties mobiles, telles que le levier de vitesse et
les rails des sièges.
Placez les câbles à lécart de tous les endroits
chauds, par exemple les sorties de chauf-
fage.
Ne reliez pas le câble jaune à la batterie à tra-
vers le trou dans le compartiment moteur.
Recouvrez tous les connecteurs de câbles qui
ne sont pas connectés avec du ruban adhésif
isolant.
Ne raccourcissez pas les câbles.
Ne coupez jamais lisolation du câble dali-
mentation de cet appareil pour partager lali-
mentation avec dautres appareils. La
capacité en courant du câble est limitée.
Utilisez un fusible correspondant aux caracté-
ristiques spécifiées.
Ne câblez jamais le câble négatif du haut-par-
leur directement à la masse.
Ne réunissez jamais ensemble les câbles né-
gatifs de plusieurs haut-parleurs.
! Lorsque cet appareil est sous tension, les si-
gnaux de commande sont transmis via le
câble bleu/blanc. Connectez ce câble à la té-
lécommande du système dun amplificateur
de puissance externe ou à la borne de
commande du relais de lantenne motorisée
du véhicule (max. 300 mA 12 V CC). Si le véhi-
cule est équipé dune antenne intégrée à la
lunette arrière, connectez-le à la borne dali-
mentation de lamplificateur dantenne.
! Ne reliez jamais le câble bleu/blanc à la
borne dalimentation dun amplificateur de
puissance externe. De même, ne le reliez pas
à la borne dalimentation de lantenne moto-
risée. Dans le cas contraire, il peut en résul-
ter un déchargement de la batterie ou un
dysfonctionnement.
! Le câble noir est la masse. Les câbles de
terre de cet appareil et dautres produits (par-
ticulièrement les produits avec des courants
élevés tels que lamplificateur de puissance)
doivent être câblés séparément. Dans le cas
contraire, ils peuvent se détacher accidentel-
lement et provoquer un incendie ou un dys-
fonctionnement.
Cet appareil
3 45
21
Français
Utilisation de lappareil
21
Section
Installation
Fr
02
03
Black plate (22,1)
1 Entrée cordon dalimentation
2 Sortie arrière ou haut-parleur dextrêmes gra-
ves
3 Entrée antenne
4 Fusible (10 A)
5 Entrée télécommande câblée
Un adaptateur de télécommande câblée
(vendu séparément) peut être connecté.
Cordon dalimentation
1
3
3
2
4
4
5
5
6
6
b
8
9
7
a
e
d
c
1 Vers lentrée cordon dalimentation
2 Selon le type de véhicule, 3 et 5 peuvent
avoir une fonction différente. Dans ce cas,
assurez-vous de connecter 4 à 5 et 6 à 3.
3 Jaune
Alimentation de secours (ou accessoire)
4 Jaune
Connectez à la borne dalimentation 12 V per-
manente.
5 Rouge
Accessoire (ou alimentation de secours)
6 Rouge
Connectez à la borne contrôlée par le
contact dallumage (12 V CC).
7 Connectez les fils de même couleur en-
semble.
8 Noir (masse du châssis)
9 Bleu/blanc
La position des broches du connecteur ISO
est différente selon le type de véhicule.
Connectez 9 et b lorsque la broche 5 est de
type commande de lantenne. Dans un type
différent de véhicule, ne connectez jamais 9
et b.
a Bleu/blanc
Connectez à la borne de commande du sys-
tème de lamplificateur de puissance (max.
300 mA 12 V CC).
b Bleu/blanc
Connectez à la borne de commande du relais
de lantenne motorisée (max. 300 mA 12 V
CC).
c Jaune/noir
Si vous utilisez un équipement avec la fonc-
tion Coupure du son, câblez ce fil au fil Cou-
pure Audio de cet équipement. Sinon, ne
connectez rien au fil Coupure Audio.
d Fils des haut-parleurs
Blanc : Avant gauche +
Blanc/noir : Avant gauche *
Gris : Avant droite +
Gris/noir : Avant droite *
Vert: Arrière gauche + ou haut-parleur dex-
trêmes graves +
Vert/noir: Arrière gauche * ou haut-parleur
dextrêmes graves *
Violet : Arrière droite + ou haut-parleur dex-
trêmes graves +
Violet/noir: Arrière droite * ou haut-parleur
dextrêmes graves *
e Connecteur ISO
Dans certains véhicules, il est possible que
le connecteur ISO soit divisé en deux. Dans
ce cas, assurez-vous de connecter les deux
connecteurs.
Remarques
! Changez le menu initial de cet appareil. Re-
portez-vous à la page 20, SP-P/O MODE (ré-
glage de la sortie arrière et du préamp).
La sortie haut-parleur dextrêmes graves de
cet appareil est monaurale.
! Lors de lutilisation dun haut-parleur dextrê-
mes graves de 70 W (2 W), assurez-vous de
connecter le haut-parleur dextrêmes graves
aux fils violet et violet/noir de cet appareil. Ne
connectez aucun périphérique aux fils vert et
vert/noir.
Amplificateur de puissance
(vendu séparément)
Réalisez ces connexions lors de lutilisation dun
amplificateur optionnel.
1
3
2
4
55
1 Télécommande du système
Connectez au câble bleu/blanc.
2 Amplificateur de puissance (vendu séparé-
ment)
3 Connectez avec des câbles RCA (vendus sé-
parément)
4 Vers la sortie arrière ou la sortie du haut-par-
leur dextrêmes graves
5 Haut-parleur arrière ou haut-parleur dextrê-
mes graves
Installation
Important
! Vérifiez toutes les connexions et tous les sys-
tèmes avant linstallation finale.
! Nutilisez pas de pièces non autorisées car il
peut en résulter des dysfonctionnements.
! Consultez votre revendeur si linstallation né-
cessite le perçage de trous ou dautres modi-
fications du véhicule.
! Ninstallez pas cet appareil :
il peut interférer avec lutilisation du véhicule.
il peut blesser un passager en cas darrêt
soudain du véhicule.
! Le laser à semi-conducteur sera endommagé
sil devient trop chaud. Installez cet appareil
àlécart de tous les endroits chauds, par
exemple les sorties de chauffage.
! Des performances optimales sont obtenues
quand lappareil est installé à un angle infé-
rieur à 60°.
60°
! Lors de linstallation, pour assurer une dis-
persion correcte de la chaleur quand cet ap-
pareil est utilisé, assurez-vous de laisser un
espace important derrière la face arrière et
enroulez les câbles volants de façon quils ne
bloquent pas les orifices daération.
5cmcm
Laissez suffisamment
d’espace
5 cm
5 cm
Montage avant/arrière DIN
Cet appareil peut être installé correctement soit
en montage frontal ou en montage arrière.
Utilisez des pièces disponibles dans le
commerce lors de linstallation.
Installation
22
Section
Installation
Fr
03
Black plate (23,1)
Montage frontal DIN
1 Insérez le manchon de montage dans le
tableau de bord.
Lors de linstallation de cet appareil dans un es-
pace peu profond, utilisez le manchon de mon-
tage fourni. Si lespace est suffisant, utilisez le
manchon de montage fourni avec le véhicule.
2 Fixez le manchon de montage en utilisant
un tournevis pour courber les pattes métalli-
ques (90°) en place.
1
2
1 Tableau de bord
2 Manchon de montage
# Assurez-vous que lappareil est correctement mis
en place. Toute installation instable peut entraîner
des sauts ou autres dysfonctionnements.
Montage arrière DIN
1 Déterminez la position appropriée les
trous sur le support et sur le côté de lappa-
reil se correspondent.
2 Serrez deux vis de chaque côté.
1
2
3
1 Vis taraudeuse (5 mm × 8 mm)
2 Support de montage
3 Tableau de bord ou console
Retrait de lappareil
1 Retirez lanneau de garniture.
1 Anneau de garniture
2 Encoche
! Retirer la face avant permet daccéder plus
facilement à lanneau de garniture.
! Quand vous remontez lanneau de garniture,
pointez le côté avec lencoche vers le bas.
2 Insérez les clés dextraction fournies dans
les deux côtés de lappareil jusquàcequel-
les senclenchent en place.
3 Tirez lappareil hors du tableau de bord.
Retrait et remontage de la face avant
Vous pouvez retirer la face avant pour protéger
lappareil contre le vol.
Appuyez sur la touche de retrait, puis poussez la
face avant vers le haut et tirez-la vers vous.
Pour les détails, reportez-vous à Retrait de la face
avant pour protéger lappareil contre le vol et à la
page 16, Remontage de la face avant .
Français
Installation
23
Section
Installation
Fr
03
Black plate (24,1)
Dépannage
Symptôme Causes possi-
bles
Action correc-
tive
Lécran re-
vient automa-
tiquement à
laffichage or-
dinaire.
Vous navez exé-
cuté aucune
opération pen-
dant 30 secon-
des.
Réexécutez lopé-
ration.
Létendue de
répétition de
lecture
change de
manière inat-
tendue.
En fonction de
létendue de ré-
pétition de lec-
ture, létendue
sélectionnée
peut changer
lors de la sélec-
tion dun autre
dossier ou
dune autre
plage ou pen-
dant lavance
ou le retour ra-
pide.
Resélectionnez
létendue de répé-
tition de lecture.
Un sous-dos-
sier nest pas
lu.
Il est impossible
de lire les sous-
dossiers lorsque
FLD (répétition
du dossier) est
sélectionné.
Sélectionnez une
autre étendue de
répétition de lec-
ture.
NO XXXX
saffiche lors
de la modifi-
cation de laf-
fichage (par
exemple NO
TITLE).
Aucune infor-
mation textuelle
nest intégrée.
Basculez laffi-
chage ou la lec-
ture sur une autre
plage/un autre fi-
chier.
Symptôme Causes possi-
bles
Action correc-
tive
Lappareil ne
fonctionne
pas correcte-
ment.
Il y a des in-
terférences.
Vous utilisez un
autre appareil,
tel quun télé-
phone cellu-
laire, qui
transmet des
ondes électro-
magnétiques à
proximité de
lappareil.
Éloignez tous les
appareils électri-
ques qui pourrait
provoquer des in-
terférences.
Messages derreur
Quand vous contactez votre distributeur ou le
Service dentretien agréé par Pioneer le plus
proche, noubliez pas de noter le message der-
reur.
Commun
Message Causes possi-
bles
Action correc-
tive
AMP ERROR Une anomalie
de fonctionne-
ment de lappa-
reil sest
produite ou la
connexion des
haut-parleurs
est incorrecte.
Le circuit de
protection est
activé.
Vérifiez la conne-
xion des haut-par-
leurs. Si le
message ne dis-
paraît pas même
après avoir éteint
puis démarré le
moteur, consultez
votre distributeur
ou un centre den-
tretien agréé par
Pioneer.
Lecteur de CD
Message Causes possi-
bles
Action correc-
tive
ERROR-07,
11, 12, 17, 30
Le disque est
sale.
Nettoyez le
disque.
Le disque est
rayé.
Utilisez un autre
disque.
ERROR-07,
10, 11, 12,
15, 17, 30,
A0
Une erreur mé-
canique ou
électrique est
survenue.
Coupez et remet-
tez le contact dal-
lumage ou
choisissez une
autre source, puis
revenez au lecteur
de CD.
ERROR-15 Le disque inséré
est vierge.
Utilisez un autre
disque.
ERROR-23 Format CD non
pris en charge.
Utilisez un autre
disque.
FORMAT
READ
Le début de la
lecture et le
début de lémis-
sion des sons
sont parfois dé-
calés.
Attendez que le
message dispa-
raisse pour enten-
dre les sons.
NO AUDIO Le disque inséré
ne contient pas
de fichiers pou-
vant être lus.
Utilisez un autre
disque.
SKIPPED Le disque inséré
contient des fi-
chiers protégés
par DRM.
Utilisez un autre
disque.
PROTECT Tous les fichiers
sur le disque in-
séré intègrent la
protection par
DRM.
Utilisez un autre
disque.
Conseils sur la manipulation
Disques et lecteur
Utilisez uniquement des disques affichant lun ou
lautre des logos suivants.
Utilisez des disques 12 cm. Nutilisez pas de dis-
ques 8 cm ni un adaptateur pour disques 8 cm.
Utilisez seulement des disques conventionnels de
forme circulaire. Nutilisez pas de disques ayant
une forme particulière.
Nintroduisez aucun objet dans le logement pour
CD autre quun CD.
Nutilisez pas de disques fendillés, ébréchés, voi-
lés ou présentant dautres défauts, car ils peuvent
endommager le lecteur.
Les disques CD-R/RW non finalisés ne peuvent
pas être lus.
Ne touchez pas la surface enregistrée des dis-
ques.
Rangez les disques dans leur coffret dès que vous
ne les écoutez plus.
Ne posez aucune étiquette sur la surface des dis-
ques, nécrivez pas sur un disque, nappliquez
aucun agent chimique sur un disque.
Pour nettoyer un CD, essuyez le disque avec un
chiffon doux en partant du centre vers lextérieur.
Informations complémentaires
24
Annexe
Informations complémentaires
Fr
Black plate (25,1)
La condensation peut perturber temporairement
le fonctionnement du lecteur. Laissez celui-ci sa-
dapter à la température plus élevée pendant une
heure environ. Essuyez également les disques hu-
mides avec un chiffon doux.
La lecture de certains disques peut être impos-
sible en raison des caractéristiques du disque, de
son format, de lapplication qui la enregistré, de
lenvironnement de lecture, des conditions de
stockage ou dautres conditions.
Les cahots de la route peuvent interrompre la lec-
ture dun disque.
Lisez les précautions demploi des disques avant
de les utiliser.
Lors de lutilisation de disques dont la surface de
létiquette est imprimable, vérifiez les instructions
et les avertissements des disques. Linsertion et
léjection peuvent ne pas être possibles selon les
disques. Lutilisation dun tel disque risque den-
dommager cet appareil.
Ne posez aucune étiquette disponible dans le
commerce ou tout autre matériau sur la surface
des disques.
! Les disques pourraient se déformer et devenir
injouables.
! Les étiquettes pourraient se décoller pendant
la lecture et empêcher léjection des disques,
ce qui pourrait endommager lappareil.
DualDiscs
Les DualDiscs sont des disques à deux faces avec
un CD enregistrable pour laudio sur une face et
un DVD enregistrable pour la vidéo sur lautre.
Comme la face CD des DualDiscs nest pas physi-
quement compatible avec le standard CD général,
la lecture de la face CD sur cet appareil peut ne
pas être possible.
Charger et éjecter fréquemment un DualDisc peut
provoquer des rayures sur le disque. Des rayures
importantes peuvent entraîner des problèmes de
lecture sur cet appareil. Dans certains cas, un
DualDisc peut se retrouver bloqué dans le loge-
ment pour CD et ne sera pas éjecté. Pour éviter
cela, nous vous recommandons de vous abstenir
dutiliser des DualDiscs avec cet appareil.
Pour des informations plus détaillées sur les
DualDiscs, veuillez vous reporter aux informations
fournies par le fabricant des disques.
Compatibilité des formats
audio compressés
WMA
Extension de fichier : .wma
Débit binaire : 48 kbit/s à 320 kbit/s (CBR), 48 kbit/s
à 384 kbit/s (VBR)
Fréquence déchantillonnage : 32 kHz, 44,1 kHz, 48
kHz
Windows Media Audio Professional, Lossless,
Voice/DRM Stream/Stream avec vidéo : incompa-
tible
MP3
Extension de fichier : .mp3
Débit binaire : 8 kbit/s à 320 kbit/s (CBR), VBR
Fréquence déchantillonnage : 8 kHz à 48 kHz
(32 kHz, 44,1 kHz, 48 kHz pour accentuation)
Version étiquette ID3 compatible : 1.0, 1.1, 2.2, 2.3,
2.4 (la Version 2.x de létiquette ID3 a priorité sur la
Version 1.x.)
Liste de lecture m3u : incompatible
MP3i (MP3 interactif), mp3 PRO : incompatible
WAV
Extension de fichier : .wav
Bits de quantification : 8 et 16 (LPCM), 4 (MS
ADPCM)
Fréquence déchantillonnage : 16 kHz à 48 kHz
(LPCM), 22,05 kHz et 44,1 kHz (MS ADPCM)
Informations supplémentaires
Seuls les 32 premiers caractères dun nom de fi-
chier (incluant lextension de fichier) ou dun nom
de dossier peuvent être affichés.
Les textes russes à afficher sur cet appareil doi-
vent être codés avec un des jeux de caractères sui-
vants :
! Unicode (UTF-8, UTF-16)
! Un jeu de caractères autre que Unicode qui
est utilisé dans un environnement Windows et
qui est paramétré sur Russe dans le réglage
multilingue
Cet appareil peut ne pas fonctionner correctement
selon lapplication utilisée pour encoder les fi-
chiers WMA.
Disque
Hiérarchie des dossiers pouvant être lus : jusquà
8 niveaux (dans la pratique, la hiérarchie compte
moins de 2 niveaux).
Dossiers pouvant être lus : jusquà99
Fichiers pouvant être lus : jusquà 999
Système de fichiers : ISO 9660 Niveau 1 et 2,
Romeo, Joliet
Lecture multi-session : compatible
Transfert des données en écriture par paquet : in-
compatible
Quelle que soit la durée du silence entre les pla-
ges musicales de lenregistrement original, la lec-
ture des disques daudio compressé seffectue
avec une courte pause entre les plages musicales.
PRÉCAUTION
Ne laissez pas de disque dans un endroit sou-
mis à des températures élevées.
Séquence des fichiers audio
Sur cet appareil, lutilisateur ne peut pas affecter
de numéros de dossier ni spécifier les séquen-
ces de lecture.
Exemple de hiérarchie
1
2
3
4
5
6
01
02
03
04
05
Niveau 1 Niveau 2 Niveau 3 Niveau 4
: Dossier
: Fichier daudio
compressé
01 à 05 : Numéro de
dossier
1 à 6 : Séquence
de lecture
Disque
La séquence de sélection des dossiers ou dau-
tres opérations peut différer en fonction du logi-
ciel de codage ou décriture.
Français
Informations complémentaires
25
Annexe
Informations complémentaires
Fr
Black plate (26,1)
Tableau des caractères
cyrilliques
D:C D:C D:C D:C D:C
: А : Б : В : Г : Д
: Е, Ё : Ж : З : И, Й : К
: Л : М : Н : О : П
: Р : С : Т : У : Ф
: Х : Ц : Ч
: Ш,
Щ
: Ъ
: Ы : Ь : Э : Ю : Я
D : Affichage C : Caractère
Droits dauteur et marques
commerciales
iTunes
Apple et iTunes sont des marques commerciales
dApple Inc., enregistrées aux États-Unis et dans
dautres pays.
MP3
La vente de ce produit comporte seulement une
licence dutilisation privée, non commerciale, et
ne comporte pas de licence ni nimplique aucun
droit dutilisation de ce produit pour une diffu-
sion commerciale (cest-à-dire générant des re-
venus) en temps réel (terrestre, par satellite,
câble et/ou tout autre média), diffusion/stream-
ing via internet, des intranets et/ou dautres sys-
tèmes électroniques de distribution de contenu,
telles que les applications audio payante ou
audio à la demande. Une licence indépendante
est requise pour de telles utilisations. Pour les
détails, veuillez visiter le site
http://www.mp3licensing.com.
WMA
Windows Media est une marque déposée ou
une marque commerciale de Microsoft
Corporation aux États-Unis et/ou dans dautres
pays.
Ce produit intègre une technologie détenue par
Microsoft Corporation, qui ne peut être utilisée
et distribuée que sous licence de Microsoft
Licensing, Inc.
Caractéristiques techniques
Généralités
Tension dalim entation ..... 14,4 V CC (10,8 V à 15,1 V ac-
ceptable)
Mise à la masse ............... Pôle négatif
Consommation maximale
................................... 10,0 A
Dimensions (L × H × P) :
DIN
Châssis .............. 178mm × 50mm ×
165 mm
Panneau avant ... 188 mm × 58 mm ×
16 mm
D
Châssis .............. 178mm × 50mm ×
165 mm
Panneau avant ... 170 mm × 46 mm ×
16 mm
Poids ............................... 1 kg
Audio
Puissance de sortie maximale
................................... 50 W × 4
70 W × 1/2 W (pour le haut-
parleur dextrêmes graves)
Puissance de sortie continue
................................... 22W × 4 (50Hz à 15000Hz,
DHT 5 %, impédance de
charge 4 W, avec les deux ca-
naux entraînés)
Impédance de charge ...... 4 W (4 W à8W acceptable)
Niveau de sortie maximum de la sortie préamp
................................... 2,0V
Correction physiologique
................................... +10dB (100 Hz), +6,5 dB
(10 kHz) (volume : 30 dB)
Égaliseur (Égaliseur graphique à 5 bandes) :
Fréquence ................. 80Hz/250 Hz/800 Hz/
2,5 kHz/8 kHz
Plage dégalisation ... ±12 dB (par pas de 2 dB)
Haut-parleur dextrême s graves (mono) :
Fréquence ................. 50Hz/63 Hz/80 Hz/100 Hz/
125 Hz/160 Hz/200 Hz
Pente ........................ 6 dB/oct, 12 dB/oct
Gain ......................... +6dB à 24 dB
Phase ....................... Normale/Inverse
Lecteur de CD
Système ........................... Compact Disc Digital Audio
Disques utilisables ........... Disques compacts
Rapport signal/bruit ......... 94dB (1kHz) (réseau IEC-A)
Nombre de canaux ........... 2 (stéréo)
Format de décodage MP3
................................... MPEG-1 & 2 Couche Audio 3
Format de décodage WMA
................................... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2ca-
naux audio)
(Windows Media Player)
Format du signal WAV ...... PCM Linéaire & MS AD PCM
(Non compressé)
Syntoniseur FM
Gamme de fréquence ....... 87,5 MHz à 108,0 MHz
Sensibilité utile ................ 9dBf (0,8 µV/75 W, mono, S/B :
30 dB)
Rapport signal/bruit ......... 72dB (réseau IEC-A)
Syntoniseur MW (PO)
Gamme de fréquence ....... 531kHz à 1 602kHz
Sensibilité utile ................ 25µV (S/B : 20 dB)
Rapport signal/bruit ......... 62dB (réseau IEC-A)
Syntoniseur LW (GO)
Gamme de fréquence ....... 153kHz à 281kHz
Sensibilité utile ................ 28µV (S/B : 20 dB)
Rapport signal/bruit ......... 62dB (réseau IEC-A)
Remarque
Les caractéristiques et la présentation peuvent
être modifiées sans avis préalable.
Informations complémentaires
26
Annexe
Informations complémentaires
Fr
Black plate (27,1)
Français
27Fr
Black plate (28,1)
Grazie per aver acquistato questo prodotto
PIONEER
Leggere attentamente questo manuale prima di
utilizzare il prodotto, per assicurarne il corretto
utilizzo. È particolarmente importante leggere e
osservare le precauzioni contrassegnate da AV-
VERTENZA e ATTENZIONE contenute in
questo manuale. Conservar e il manuale in un
luogo sicuro e accessibile, per consultazione futu-
ra.
Se si vuole eliminare questo prodotto, non
gettarlo insieme ai rifiuti domestici. Esiste un
sistema di raccolta differenziata in conformità
alle leggi che richiedono appositi trattamenti,
recupero e riciclo.
Gli utenti privati dei Paesi membri dellUnione
Europea, della Svizzera e della Norvegia posso-
no portare i propri prodotti elettronici gratuita-
mente presso i centri di raccolta specificati o
presso il rivenditore al dettaglio (se lacquisto è
stato eseguito presso un rivenditore di questo
tipo).
Per i Paesi non specificati in precedenza, contat-
tare le autorità locali per informazioni sul corret-
to metodo di smaltimento.
In questo modo si garantirà che il prodotto
smaltito subisca i processi di trattamento, recu-
pero e riciclaggio necessari per prevenire i po-
tenziali effetti negativi per lambiente e la salute
umana.
Informazioni sullunità
Le frequenze del sintonizzatore di questa unità
sono destinate alluso in Europa occidentale, in
Asia, nel Medio Oriente, in Africa e in Oceania.
Luso in altre aree può dare come risultato una
ricezione non adeguata. La funzione RDS (Radio
Data System) è operativa solo nelle aree in cui
vengono trasmessi segnali RDS per stazioni FM.
ATTENZIONE
Questo apparecchio è un prodotto al laser di
Classe 1 secondo le norme di sicurezza dei
prodotti al laser IEC 60825-1:2007.
PRODOTTO LASER DI CLASSE 1
ATTENZIONE
! Non lasciare che questa unità entri in contat-
to con liquidi, in caso contrario possono veri-
ficarsi scosse elettriche. Inoltre, se questa
unità entra in contatto con liquidi, può subire
danni oppure emettere fumo o surriscaldar-
si.
! Il CarStereo-Pass Pioneer può essere usato
solo in Germania.
! Mantenere sempre il volume basso abba-
stanza da poter udire i suoni provenienti dal-
lesterno.
! Evitare lesposizione allumidità.
! Se la batteria viene scollegata o si scarica, la
memoria delle preselezioni viene cancellata.
Nota
Le operazioni di impostazione delle funzioni ven-
gono completate anche se il menu viene chiuso
prima della conferma.
In caso di problemi
Nel caso che questa unità non funzioni corretta-
mente, contattare il rivenditore o il Centro di as-
sistenza autorizzato PIONEER più vicino.
Prima di iniziare
28
Sezione
Prima di iniziare
It
01
Black plate (29,1)
Unità principale
b c
5
8
1 2 3 4 6
a9d7
Componente Componente
1 h (espulsione) 8 BAND
2 SRC/OFF 9
(indietro)/
DIMMER (varialu-
ce)
3
MULTI-CONTROL
(M.C.)
a c/d
4
(lista) b Da 1/ a 6/
5 DISP c
Connettore di in-
gresso ausiliario
(AUX) (connettore
stereo da 3,5 mm)
6
Vano dinserimen-
to dei dischi
d Tasto Rimozione
7
(equalizzato-
re)
Indicazioni sul display
21 3 75
9
4 6 8
a
Indicatore Stato
1
(lista) La funzione elenco è attiva.
2
Sezione
delle infor-
mazioni se-
condarie
Vengono visualizzate le infor-
mazioni secondarie.
3
TA (notiziari
sul traffico)
La funzione TA è attivata.
4
TP (identifi-
cazione dei
programmi
sul traffico)
È sintonizzata una stazione
TP.
5
(Sound Re-
triever)
È attivata la funzione Sound
Retriever.
6 LOC
La ricerca di sintonia in modo
locale è attiva.
7
(ripeti-
zione)
È attiva la funzione di riprodu-
zione cartella.
8
(casua-
le)
È attiva la riproduzione casua-
le.
9
Sezione
delle infor-
mazioni
principali
! Sintonizzatore: banda e
frequenza
! RDS: nome di servizio del
programma, informazioni
PTY e altre informazioni
letterali
! Lettore CD: tempo di ripro-
duzione trascorso e infor-
mazioni di testo
a
Viene visualizzato quando esi-
ste una cartella o un menu di
livello inferiore.
Menu di configurazione
Portando su ON linterruttore della chiave di av-
viamento dopo linstallazione, sul display com-
pare il menu di configurazione.
È possibile configurare le opzioni di menu ripor-
tate di seguito.
1 Dopo aver installato lunità, portare lin-
terruttore della chiave di avviamento su ON.
Viene visualizzata lindicazione SET UP.
2 Ruotare M.C. per selezionare YES.
# Se non si effettuano operazioni per 30 secondi, il
menu di configurazione non sarà visualizzato.
# Se non si desidera eseguire la configurazione in
questo momento, ruotare M.C. per selezionare NO.
Premere per selezionare.
Se si seleziona NO, non è possibile definire le impo-
stazioni nel menu di configurazione.
3 Premere M.C. per selezionare.
4 Attenersi alle procedure descritte di se-
guito per configurare il menu.
Per passare allopzione di menu successiva, oc-
corre confermare la selezione.
LANGUAGE (multilingue)
Questa unità è in grado di visualizzare le informa-
zioni di testo dei file audio compressi se sono
state incorporate in inglese o russo.
! Se la lingua incorporata e limpostazione della
lingua selezionata non corrispondono, le infor-
mazioni di testo potrebbero non essere visua-
lizzate correttamente.
! Alcuni caratteri potrebbero non essere visualiz-
zati correttamente.
1 Ruotare M.C. per selezionare limpostazione
desiderata.
ENG (Inglese)РУС (Russo)
2 Premere M.C. per confermare la selezione.
CLOCK SET (impostazione dellorologio)
1 Ruotare M.C. per regolare le ore.
2 Premere M.C. per selezionare i minuti.
3 Ruotare M.C. per regolare i minuti.
4 Premere M.C. per confermare la selezione.
FM STEP (passo di sintonizzazione FM)
Normalmente il passo per la sintonizzazione in FM
impiegato dalla ricerca di sintonia è 50 kHz. Se
sono attivate le funzioni AF o TA il passo di sinto-
nizzazione cambia automaticamente a 100 kHz. Se
è attivata la funzione AF, è preferibile impostare il
passo di sintonizzazione a 50 kHz.
! Il passo di sintonizzazione rimane a 50 kHz du-
rante la sintonizzazione manuale.
1 Ruotare M.C. per selezionare il passo di sinto-
nizzazione FM.
50 (50 kHz)100 (100 kHz)
2 Premere M.C. per confermare la selezione.
Viene visualizzata lindicazione QUIT.
5 Per completare le impostazioni, ruotare
M.C. per selezionare YES.
# Se si desidera modificare nuovamente limposta-
zione, ruotare M.C. per selezionare NO. Premere per
selezionare.
6 Premere M.C. per selezionare.
Note
! È possibile configurare le opzioni di menu
dal menu di sistema. Per informazioni detta-
gliate sulle impostazioni, vedere Menu di si-
stema a pagina 33.
! È possibile annullare il menu di configurazio-
ne premendo SRC/OFF.
Funzionamento di base
Importante
! Rimuovere e inserire il frontalino delicata-
mente.
Italiano
Funzionamento dellunità
29
Sezione
Funzionamento dellunità
It
02
Black plate (30,1)
! Evitare di sottoporre il frontalino a urti ecces-
sivi.
! Mantenere il frontalino lontano dalla luce so-
lare diretta e dalle alte temperature.
! Per evitare danni ai dispositivi o agli interni
del veicolo, accertarsi di scollegare gli even-
tuali cavi e i dispositivi collegati al frontalino,
prima di rimuoverlo.
Rimozione del frontalino per proteggere lunità dai
furti
1 Premere il tasto di rimozione per sganciare il
frontalino.
2 Spingere il frontalino verso lalto (M) e quindi ti-
rarlo verso lesterno (N).
3 Tenere sempre il frontalino nella custodia di
protezione quando non è collegato allunità.
Reinserimento del frontalino
1 Fare scorrere il frontalino verso sinistra.
Inserire le linguette sul lato sinistro dellunità
principale nei corrispondenti alloggiamenti sul
frontalino.
2 Premere il lato destro del frontalino fino a
quando è saldamente installato.
Se non è possibile collegare il frontalino allu-
nità principale, accertarsi di aver posizionato il
frontalino sullunità principale in modo corret-
to. Inserendo il frontalino con forza eccessiva,
lunità o il frontalino potrebbero subire danni.
Accensione dellunità
1 Premere SRC/OFF per accendere lunità.
Spegnimento dellunità
1 Premere e tenere premuto SRC/OFF fino a
quando lunità non si spegne.
Selezione di una sorgente
1 Premere SRC/OFF per passare in rassegna:
TUNER (Sintonizzatore)CD (Lettore CD)
AUX (AUX)
Regolazione del volume
1 Ruotare M.C. per regolare il volume.
ATTENZIONE
Per motivi di sicurezza, parcheggiare il veicolo
quando si rimuove il frontalino.
Nota
Quando il conduttore isolato blu/bianco di que-
sta unità viene collegato al terminale di controllo
del relè dellantenna automatica, lantenna del-
lautomobile si estende quando si accende luni-
tà. Per ritirare lantenna, spegnere la sorgente.
Operazioni col menu più
frequentemente utilizzate
Ritorno al display precedente
Ritorno allelenco precedente (la cartella superio-
re di un livello)
1 Premere
/DIMMER.
Ritorno al display normale
Annullamento del menu principale
1 Premere BAND.
Ritorno al display normale dallelenco
1 Premere BAND.
Sintonizzatore
Funzionamento di base
Selezione di una banda
1 Premere BAND fino a quando viene visualizza-
ta la banda desiderata (FM1, FM2, FM3 per
FM o MW/LW).
Selezione delle stazioni preselezionate
1 Premere c o d.
! Selezionare PCH (canale preselezionato) in
SEEK per utilizzare questa funzione. Per infor-
mazioni dettagliate sulle impostazioni, vedere
SEEK (impostazione tasto sinistro/destro) nella
pagina seguente.
Sintonizzazione manuale (passo per passo)
1 Premere c o d.
! Selezionare MAN (sintonizzazione manuale)
in SEEK per utilizzare questa funzione. Per in-
formazioni dettagliate sulle impostazioni, vede-
re SEEK (impostazione tasto sinistro/destro)
nella pagina seguente.
Ricerca
1 Premere e tenere premuto c o d e poi rilascia-
re.
È possibile annullare la ricerca di sintonia pre-
mendo brevemente c o d.
Se si spinge e si tiene premuto c o d, è possi-
bile saltare le stazioni. La ricerca di sintonia
viene avviata non appena si rilascia c o d.
Nota
È possibile attivare e disattivare (on/off) la fun-
zione AF (ricerca delle frequenze alternative) di
questa unità. Per le operazioni normali di sinto-
nizzazione, la funzione AF deve essere disattiva-
ta (vedere AF (ricerca delle frequenze alternative)
nella pagina seguente).
Memorizzazione e richiamo delle
stazioni per ciascuna banda
Uso dei tasti di preselezione sintonia
1 Quando viene individuata una stazione
che si desidera memorizzare, premere uno
dei tasti di preselezione sintonia (da 1/
a6/
), mantenendolo premuto fino a quando
il numero di preselezione non cessa di lam-
peggiare.
2 Premere e tenere premuto uno dei tasti
di preselezione sintonia (da 1/
a6/ ) per
selezionare la stazione desiderata.
Commutazione del display
Selezione delle informazioni di testo desiderate
1 Premere DISP per alternare le seguenti impo-
stazioni:
! FREQUENCY (nome di servizio del pro-
gramma o frequenza)
! BRDCST INFO (nome di servizio del pro-
gramma/Informazioni PTY)
! CLOCK (nome della sorgente e orologio)
Note
! Se non è possibile ottenere il nome di servi-
zio del programma in FREQUENCY, al suo
posto viene visualizzata la frequenza di tra-
smissione. Se invece il nome di servizio del
programma viene rilevato, verrà visualizzato.
! BRDCST INFO le informazioni di testo cam-
bieranno automaticamente.
! È possibile modificare le informazioni a se-
conda della banda.
! Le informazioni di testo che possono essere
modificate dipendono dallarea.
Uso delle funzioni PTY
È possibile sintonizzarsi su una stazione usando
le informazioni PTY (tipo di programma).
Funzionamento dellunità
30
Sezione
Funzionamento dellunità
It
02
Black plate (31,1)
Ricerca di una stazione RDS tramite le informazio-
ni PTY
È possibile ricercare programmi di trasmissioni di
tipo generale, come quelli elencati nella sezione
seguente. Vedere in questa pagina.
1 Premere
(elenco).
2 Ruotare M.C. per selezionare un tipo di pro-
gramma.
NEWS/INFOPOPULARCLASSICS
OTHERS
3 Premere M.C. per avviare la ricerca.
Lunità ricerca una stazione che trasmette il
tipo di programma selezionato. Quando viene
trovata una stazione, viene visualizzato il nome
di ser vizio del programma.
! Per annullare la ricerca premere nuova-
mente M.C.
! Il programma di alcune stazioni può essere
diverso da quello indicato dal PTY (tipo di
programma) trasmesso.
! Se nessuna stazione trasmette il tipo di
programma ricercato, per circa due secon-
di viene visualizzata lindicazione NOT
FOUND e poi il sintonizzatore torna alla
stazione originale.
Elenco PTY
NEWS/INFO (notizie e informazioni)
NEWS (Notizie), AFFAIRS (Problemi attuali), INFO
(Informazione), SPORT (Sport), WEATHER (Infor-
mazioni meteorologiche), FINANCE (Economia)
POPULAR (musica pop)
POP MUS (Musica popolare), ROCK MUS (Musica
rock), EASY MUS (Musica rilassante), OTH MUS
(Altra musica), JAZZ (Jazz), COUNTRY (Musica
Country), NAT MUS (Musica nazionale), OLDIES
(Vecchi successi), FOLK MUS (Musica Folk)
CLASSICS (musica classica)
L. CLASS (Musica classica leggera), CLASSIC (Mu-
sica classica)
OTHERS (altro)
EDUCATE (Educazione), DRAMA (Teatro), CULTU-
RE (Cultura), SCIENCE (Scienza), VARIED (Varietà),
CHILDREN (Bambini), SOCIAL (Questioni sociali),
RELIGION (Religione), PHONE IN (Chiamate in di-
retta), TOURING (Viaggi), LEISURE (Tempo libero),
DOCUMENT (Documentari)
Impostazioni delle funzioni
1 Premere M.C. per visualizzare il menu
principale.
2 Ruotare M.C. per modificare lopzione di
menu; premere per selezionare FUNCTION.
3 Ruotare M.C. per selezionare la funzione.
Dopo aver effettuato la selezione, è possibile re-
golare le funzioni descritte di seguito.
# Se è selezionata la banda MW/LW, è possibile se-
lezionare solo BSM, LOCAL o SEEK.
BSM (memorizzazione delle stazioni migliori)
La funzione BSM (memorizzazione delle stazioni
migliori) memorizza automaticamente le sei sta-
zioni più forti in ordine di forza del segnale.
1 Premere M.C. per attivare la funzione BSM.
Per annullare, premere nuovamente M.C.
REGION (regionale)
Quando si utilizza la funzione AF, la funzione regio-
nale limita la selezione alle stazioni che trasmetto-
no programmi regionali.
1 Premere M.C. per attivare o disattivare la fun-
zione regionale.
LOCAL (ricerca di sintonia in modo locale)
La ricerca di sintonia in modo locale consente di
sintonizzare solo le stazioni radio con segnali
radio sufficientemente potenti per una buona rice-
zione.
1 Premere M.C. per selezionare limpostazione
desiderata.
FM: OFFLV1LV2LV3LV 4
MW/LW: OFFLV1 LV2
Limpostazione di livello massimo consente la
ricezione solo delle stazioni più forti, mentre i
livelli più bassi consentono di ricevere stazioni
più deboli.
TA (attesa di notiziari sul traffico)
1 Premere M.C. per attivare o disattivare lattesa
di notiziari sul traffico.
AF (ricerca delle frequenze alternative)
1 Premere M.C. per attivare e disattivare la fun-
zione AF.
NEWS (interruzione dei programmi per i notiziari)
1 Premere M.C. per attivare o disattivare la fun-
zione NOTIZIE.
SEEK (impostazione tasto sinistro/destro)
È possibile assegnare una funzione ai tasti sinistro
e destro dellunità.
Selezionare MAN (sintonizzazione manuale) per
eseguire la sintonizzazione manuale o PCH (canali
preselezionati) per scegliere i canali preseleziona-
ti.
1 Premere M.C. per selezionare MAN o PCH.
CD/CD-R/CD-RW
Funzionamento di base
Riproduzione di CD/CD-R/CD-RW
1 Inserire un disco nel vano dinserimento dei di-
schi, con il lato delletichetta rivolto verso
lalto.
Espulsione dei CD/CD-R/CD-RW
1 Premere h.
Selezione di una cartella
1 Premere 1/
o 2/ .
Selezione di una traccia
1 Premere c o d.
Esegue lavanzamento rapido/la modalità inversa
rapida
1 Premere e tenere premuto c o d.
! Quando si riproducono file audio compressi,
durante lavanzamento rapido e la modalità in-
versa non viene emesso audio.
Ritorno alla cartella principale
1 Premere e tenere premuto BAND.
Passaggio da audio compresso a CD-DA
1 Premere BAND.
Italiano
Funzionamento dellunità
31
Sezione
Funzionamento dellunità
It
02
Black plate (32,1)
Commutazione del display
Selezione delle informazioni di testo desiderate
1 Premere DISP per alternare le seguenti impo-
stazioni:
CD-DA
! ELAPSED TIME (numero di brano e tempo
di riproduzione)
! CLOCK (nome della sorgente e orologio)
! SPEANA (analizzatore di spettro)
CD-TEXT
! TRACK INFO (titolo del brano/artista del
brano/titolo del disco)
! ELAPSED TIME (numero di brano e tempo
di riproduzione)
! CLOCK (nome della sorgente e orologio)
! SPEANA (analizzatore di spettro)
MP3/WMA/WAV
! TRACK INFO (titolo del brano/nome del-
lartista/titolo dellalbum)
! FILE INFO (nome del file/nome della cartel-
la)
! ELAPSED TIME (numero di brano e tempo
di riproduzione)
! CLOCK (nome della sorgente e orologio)
! SPEANA (analizzatore di spettro)
Note
! Le informazioni di testo TRACK INFO e
FILE INFO cambieranno automaticamente.
! A seconda della versione di iTunes utilizzata
per scrivere i file MP3 o del tipo di file multi-
mediali, il testo memorizzato su un file audio
potrebbe essere incompatibile e non essere
visualizzato correttamente.
! Le informazioni di testo che possono essere
cambiate dipendono dal tipo di supporto.
Selezione e riproduzione di file/
brani dallelenco dei nomi
1 Premere per passare alla modalità del-
lelenco dei nomi file/brani.
2 Utilizzare M.C. per selezionare il nome
del file (o il nome della cartella) desiderato.
Selezione di un file o di una cartella
1 Ruotare M.C.
Riproduzione
1 Quando è selezionato un file o un brano, pre-
mere M.C.
Visualizzazione di un elenco dei file (o delle cartel-
le) nella cartella selezionata
1 Quando è selezionata una cartella, premere
M.C.
Riproduzione di un brano nella cartella seleziona-
ta
1 Quando è selezionata una cartella, premere e
tenere premuto M.C.
Operazioni con i pulsanti speciali
Selezione di un intervallo di ripetizione
1 Premere 6/
per alternare:
! ALL Ripete tutti i brani
! ONE Ripete il brano corrente
! FLD Ripete la cartella corrente
Riproduzione di brani in ordine casuale
1 Premere 5/
per attivare o disattivare la ri-
produzione casuale.
I brani contenuti nellintervallo di ripetizione
selezionato vengono riprodotti in ordine casua-
le.
! Per cambiare brano durante la riproduzione
casuale, premere d per passare al brano suc-
cessivo. Se si preme c, viene riavviata la ripro-
duzione del brano corrente dallinizio.
Messa in pausa della riproduzione
1 Premere 4/PAUSE per attivare o disattivare la
pausa.
Miglioramento dellaudio compresso e ripristino
del suono completo (funzione Sound Retriever)
1 Premere 3/S.Rtrv per passare in rassegna:
12OFF (disattivata)
1 è efficace per le velocità di compressione
basse, mentre 2 è efficace per le velocità di
compressione alte.
Impostazioni delle funzioni
1 Premere M.C. per visualizzare il menu
principale.
2 Ruotare M.C. per modificare lopzione di
menu; premere per selezionare FUNCTION.
Dopo aver effettuato la selezione, è possibile re-
golare la funzione descritta di seguito.
S.RTRV (Sound Retriever)
Questa funzione migliora automaticamente lau-
dio compresso e ripristina il suono completo.
1 Premere M.C. per selezionare limpostazione
desiderata.
Per ulteriori dettagli, vedere Miglioramento del-
laudio compresso e ripristino del suono com-
pleto (funzione Sound Retriever) in questa
pagina.
Regolazione dellaudio
1 Premere M.C. per visualizzare il menu
principale.
2 Ruotare M.C. per modificare lopzione di
menu; premere per selezionare AUDIO.
3 Ruotare M.C. per selezionare la funzione
audio.
Dopo aver effettuato la selezione, è possibile re-
golare le funzioni audio descritte di seguito.
! FADER non è disponibile se limpostazione
SUB.W/SUB.W è selezionata in
SP-P/O MODE. Per ulteriori dettagli, vedere
SP-P/O MODE (uscita posteriore e impostazio-
ne pre-out) a pagina 34.
! SUB.W, SUB.W CTRL e HPF SETTING non
sono disponibili se limpostazione
REAR/REAR è selezionata in SP-P/O MODE.
Per ulteriori dettagli, vedere SP-P/O MODE
(uscita posteriore e impostazione pre-out) a
pagina 34.
! SUB.W CTRL e HPF SETTING non sono di-
sponibili se limpostazione SUB.W è selezio-
nata in OFF. Per ulteriori dettagli, vedere
SUB.W (impostazione on/off del subwoofer)
nella pagina seguente.
FADER (regolazione dissolvenza)
1 Premere M.C. per visualizzare la modalità di
impostazione.
2 Ruotare M.C. per regolare il bilanciamento
degli altoparlanti anteriori/posteriori.
BALANCE (regolazione del bilanciamento)
1 Premere M.C. per visualizzare la modalità di
impostazione.
2 Ruotare M.C. per regolare il bilanciamento del-
laltoparlante sinistro/destro.
EQ SETTING (richiamo dellequalizzatore)
Funzionamento dellunità
32
Sezione
Funzionamento dellunità
It
02
Black plate (33,1)
1 Premere M.C. per visualizzare la modalità di
impostazione.
2 Ruotare M.C. per selezionare lequalizzatore.
POWERFULNATURALVOCALCU-
STOM1CUSTOM2FLATSUPER BASS
La banda di equalizzazione e il livello dellequa-
lizzatore possono essere personalizzati se è se-
lezionata limpostazione CUSTOM1 o
CUSTOM2.
Se si seleziona CUSTOM1 o CUSTOM2, com-
pletare la procedure descritta di seguito. Se si
selezionano altre opzioni, premere M.C. per
tornare al display precedente.
! Limpostazione CUSTOM1 può essere im-
postata separatamente per ciascuna sor-
gente.
! CUSTOM2 èunimpostazione condivisa
utilizzata per tutte le sorgenti.
3 Premere M.C. per visualizzare la modalità di
impostazione.
4 Premere M.C. per alternare le seguenti impo-
stazioni:
Banda dequalizzazioneLivello equalizzatore
5 Ruotare M.C. per selezionare limpostazione
desiderata.
Banda dequalizzazione: 80HZ250HZ
800HZ2.5KHZ8KHZ
Livello equalizzatore: +6 a 6
! È inoltre possibile cambiare lequalizzatore
premendo ripetutamente
.
LOUDNESS (sonorità)
La sonorità compensa le deficienze nelle gamme
delle frequenze basse e alte a basso volume.
1 Premere M.C. per selezionare limpostazione
desiderata.
OFF (non attiva)LOW (bassa)MID (media)
HI (alta)
SUB.W (impostazione on/off del subwoofer)
Questa unità è dotata di unuscita subwoofer che
può essere attivata o disattivata.
1 Premere M.C. per selezionare limpostazione
desiderata.
NOR (fase normale)REV (fase invertita)
OFF (subwoofer disattivato)
SUB.W CTRL (regolazione del subwoofer)
Solo frequenze più basse di quelle presenti nellin-
tervallo selezionato vengono emesse dal subwoo-
fer.
1 Premere M.C. per visualizzare la modalità di
impostazione.
2 Premere M.C. per alternare le seguenti impo-
stazioni:
Frequenza di taglioLivello di uscitaLivello
pendenza
I valori regolabili lampeggiano.
3 Ruotare M.C. per selezionare limpostazione
desiderata.
Frequenza di taglio: 50HZ63HZ80HZ
100HZ125HZ160HZ200HZ
Livello di uscita: da 24 a +6
Livello pendenza: 6 12
BASS BOOST (incremento dei bassi)
1 Premere M.C. per visualizzare la modalità di
impostazione.
2 Ruotare M.C. per selezionare il livello desidera-
to.
A seconda se il livello aumenta o diminuisce,
viene visualizzata lindicazione da 0 a +6.
HPF SETTING (regolazione del filtro passa alto)
Se si desidera che i suoni bassi provenienti dalla
gamma di frequenza delluscita subwoofer non
siano riprodotti dagli altoparlanti anteriori o poste-
riori, attivare la funzione HPF (filtro passa alto).
Solo le frequenze più alte di quelle comprese nel-
lintervallo selezionato vengono emesse dagli alto-
parlanti anteriori o posteriori.
1 Premere M.C. per visualizzare la modalità di
impostazione.
2 Premere M.C. per alternare le seguenti impo-
stazioni:
Frequenza di taglioLivello pendenza
3 Ruotare M.C. per selezionare limpostazione
desiderata.
Frequenza di taglio: OFF50HZ63HZ
80HZ100HZ125HZ160HZ200HZ
Livello pendenza: 6 12
SLA (regolazione del livello della sorgente)
SLA (funzione di regolazione del livello della sor-
gente) consente di regolare il livello di volume di
ogni sorgente per prevenire cambiamenti radicali
di volume quando si passa da una sorgente allal-
tra.
! Le impostazioni sono basate sul livello di volu-
me FM, che rimane immutato.
! Con questa funzione è anche possibile regola-
re il livello di volume MW/LW.
! Quando si seleziona FM come sorgente, non è
possibile passare alla funzione SLA.
1 Premere M.C. per visualizzare la modalità di
impostazione.
2 Ruotare M.C. per regolare il volume della sor-
gente.
Intervallo di regolazione: da +4 a 4
Menu di sistema
Importante
La modalità PW SAVE (risparmio energetico)
viene annullata se la batteria del veicolo viene
scollegata e sarà necessario riattivarla dopo
aver ricollegato la batteria. Se la funzione
PW SAVE (risparmio energetico) è disattivata, a
seconda del metodo di collegamento, lunità po-
trebbe continuare a consumare energia dalla
batteria se linterruttore della chiave di avvia-
mento del veicolo non è dotato di posizione ACC
(accessori).
1 Premere M.C. per visualizzare il menu
principale.
2 Ruotare M.C. per modificare lopzione di
menu; premere per selezionare SYSTEM.
3 Ruotare M.C. per selezionare la funzione
del menu di sistema.
Dopo aver effettuato la selezione, è possibile re-
golare le funzioni del menu di sistema descritte
di seguito.
LANGUAGE (multilingue)
Questa unità è in grado di visualizzare le informa-
zioni di testo dei file audio compressi se sono
state incorporate in inglese o russo.
! Se la lingua incorporata e limpostazione della
lingua selezionata non corrispondono, le infor-
mazioni di testo potrebbero non essere visua-
lizzate correttamente.
! Alcuni caratteri potrebbero non essere visualiz-
zati correttamente.
1 Ruotare M.C. per selezionare limpostazione
desiderata.
ENG (Inglese)РУС (Russo)
CLOCK SET (impostazione dellorologio)
Italiano
Funzionamento dellunità
33
Sezione
Funzionamento dellunità
It
02
Black plate (34,1)
1 Premere M.C. per visualizzare la modalità di
impostazione.
2 Premere M.C. per selezionare il segmento del
display dellorologio che si desidera impostare.
OraMinuto
3 Ruotare M.C. per regolare lorologio.
12H/24H (nota temporale)
1 Premere M.C. per selezionare limpostazione
desiderata.
12H (formato orologio a 12 ore)24H (formato
orologio a 24 ore)
AUTO PI (ricerca automatica PI)
Lunità può ricercare automaticamente una stazio-
ne diversa con la stessa programmazione, anche
durante il richiamo delle preselezioni.
1 Premere M.C. per attivare o disattivare la ricer-
ca automatica PI.
AUX (ingresso ausiliario)
Attivare questa impostazione se a questa unità
viene collegato un dispositivo ausiliario.
1 Premere M.C. per attivare o disattivare AUX.
MUTE MODE (modalità di silenziamento)
Il suono del sistema viene silenziato o attenuato
automaticamente quando viene ricevuto un se-
gnale da un apparecchio dotato di funzione di si-
lenziamento.
1 Premere M.C. per visualizzare la modalità di
impostazione.
2 Ruotare M.C. per selezionare limpostazione
desiderata.
È possibile selezionare una delle opzioni dalle-
lenco seguente:
! MUTE Silenziamento
! 20dB ATT Attenuazione (20dB ATT ha un
effetto più accentuato rispetto a 10dB ATT)
! 10dB ATT Attenuazione
PW SAVE (risparmio energetico)
Attivando questa funzione, è possibile ridurre il
consumo di energia della batteria.
! Lattivazione della sorgente è lunica operazio-
ne consentita quando questa funzione è attiva.
1 Premere M.C. per attivare o disattivare la mo-
dalità di risparmio energetico.
Attivazione/disattivazione
del varialuce
È possibile regolare il livello della luminosità.
1 Premere M.C. per visualizzare il menu
principale.
2 Ruotare M.C. per visualizzare ILLUMI,
quindi premere per selezionare.
3 Premere M.C. per selezionare limposta-
zione desiderata.
OFF (disattivato)ON (attivato)
! È inoltre possibile modificare limpostazione
del varialuce premendo e tenendo premuto
/DIMMER.
Menu iniziale
1 Premere e tenere premuto SRC/OFF fino
a quando lunità non si spegne.
2 Premere e tenere premuto SRC/OFF fino
a visualizzare sul display il menu principale.
3 Ruotare M.C. per modificare lopzione di
menu; premere per selezionare INITIAL.
4 Ruotare M.C. per selezionare la funzione
del menu iniziale.
Dopo aver effettuato la selezione, è possibile re-
golare le funzioni del menu iniziale descritte di
seguito.
FM STEP (passo di sintonizzazione FM)
Normalmente il passo per la sintonizzazione in FM
impiegato dalla ricerca di sintonia è 50 kHz. Se
sono attivate le funzioni AF o TA il passo di sinto-
nizzazione cambia automaticamente a 100 kHz. Se
è attivata la funzione AF, è preferibile impostare il
passo di sintonizzazione a 50 kHz.
! Il passo di sintonizzazione rimane a 50 kHz du-
rante la sintonizzazione manuale.
1 Premere M.C. per selezionare il passo di sinto-
nizzazione FM.
50 (50 kHz)100 (100 kHz)
SP-P/O MODE (uscita posteriore e impostazione
pre-out)
Le uscite degli altoparlanti posteriori e luscita
RCA di questa unità possono essere utilizzate per
collegare altoparlanti a gamma completa o un
subwoofer. Selezionare lopzione più adatta alla
configurazione.
1 Premere M.C. per visualizzare la modalità di
impostazione.
2 Ruotare M.C. per selezionare limpostazione
desiderata.
È possibile selezionare una delle opzioni dalle-
lenco seguente:
! REAR/SUB.W Selezionare quando alle
uscite degli altoparlanti posteriori sono col-
legati altoparlanti a gamma completa e al-
luscita RCA è collegato un subwoofer.
! SUB.W/SUB.W Selezionare quando alle
uscite degli altoparlanti posteriori è colle-
gato direttamente un subwoofer senza un
amplificatore ausiliario e alluscita RCA è
collegato un subwoofer.
! REAR/REAR Selezionare quando alle
uscite degli altoparlanti posteriori e allu-
scita RCA sono collegati altoparlanti a
gamma completa.
Se alle uscite degli altoparlanti posteriori è
collegato un altoparlante a gamma com-
pleta e luscita RCA non viene utilizzata, è
possibile selezionare REAR/SUB.W o
REAR/REAR.
Menu di sistema
1 Premere e tenere premuto SRC/OFF fino
a quando lunità non si spegne.
2 Premere e tenere premuto SRC/OFF fino
a visualizzare sul display il menu principale.
3 Ruotare M.C. per modificare lopzione di
menu; premere per selezionare SYSTEM.
Funzionamento dellunità
34
Sezione
Funzionamento dellunità
It
02
Black plate (35,1)
4 Ruotare M.C. per selezionare la funzione
del menu di sistema.
Dopo aver effettuato la selezione, è possibile re-
golare le funzioni del menu di sistema descritte
di seguito.
Per ulteriori dettagli, vedere Menu di sistema a
pagina 33.
Uso della sorgente AUX
1 Collegare il cavo mini plug stereo al con-
nettore di ingresso ausiliario (AUX).
2 Premere SRC/OFF per selezionare AUX
come sorgente.
Nota
Non è possibile selezionare la sorgente AUX se
non viene attivata limpostazione dellapparec-
chio ausiliario. Per ulteriori dettagli, vedere AUX
(ingresso ausiliario) nella pagina precedente.
Commutazione del display
Selezione delle informazioni di testo desiderate
1 Premere DISP per alternare le seguenti impo-
stazioni:
! Nome sorgente
! Nome della sorgente e orologio
Se viene visualizzato un
display indesiderato
Per disattivare il display indesiderato, utilizzare
la procedura descritta di seguito.
1 Premere M.C. per visualizzare il menu
principale.
2 Ruotare M.C. per modificare lopzione di
menu; premere per selezionare SYSTEM.
3 Ruotare M.C. per visualizzare DEMO OFF,
quindi premere per selezionare.
4 Ruotare M.C. per selezionare YES.
5 Premere M.C. per selezionare.
Collegamenti
Importante
! Quando si installa questa unità in un veicolo
che non dispone della posizione ACC (acces-
soria) per linterruttore della chiave di avvia-
mento, se non si collega il cavo rosso a un
terminale accoppiato al funzionamento del-
linterruttore della chiave di avviamento, la
batteria potrebbe scaricarsi.
O
N
S
T
A
R
T
O
F
F
Con posizione ACC Senza posizione ACC
! Se questa unità viene utilizzata in condizione
diverse dalle seguenti, potrebbero verificarsi
incendi o malfunzionamenti.
Veicoli dotati di batteria da 12 volt e messa a
terra negativa.
Altoparlanti con uscita nominale da 50 W e
impedenza nominale compresa tra 4 W e8W.
! Per evitare rischi di cortocircuito, surriscalda-
mento o malfunzionamento, accertarsi di se-
guire le indicazioni riportate di seguito.
Prima dellinstallazione, scollegare il morset-
to negativo della batteria.
Assicurare i cavi con morsetti per cavi o na-
stro adesivo. Per proteggere i cavi, avvolgere
nastro adesivo attorno agli stessi nei punti in
cui entrano in contatto con parti metalliche.
Posizionare tutti i cavi in modo che non pos-
sano entrare in contatto con componenti mo-
bili, come la leva del cambio e i binari dei
sedili.
Non posizionare i cavi in luoghi soggetti a
surriscaldamento, come le bocchette dellim-
pianto di riscaldamento.
Non collegare il cavo giallo alla batteria fa-
cendolo passare attraverso fori nel vano mo-
tore.
Rivestire tutti i connettori scollegati con na-
stro isolante.
Non accorciare i cavi.
Non condividere mai lalimentazione con altri
dispositivi tagliando lisolante del cavo di ali-
mentazione dellunità. La capacità di carico
di corrente del cavo è limitata.
Utilizzare esclusivamente un fusibile con la
portata prescritta.
Non collegare mai direttamente a terra il
cavo negativo dellaltoparlante.
Non legare mai assieme cavi negativi di più
altoparlanti.
! Quando questa unità è accesa, i segnali di
controllo vengono trasmessi dal cavo blu/
bianco. Collegarlo al telecomando del siste-
ma di amplificazione di potenza o al termina-
le di controllo del relè dellantenna
automatica del veicolo (max. 300 mA
12 V CC). Se il veicolo è dotato di unantenna
a vetro, collegarla al terminale di alimentazio-
ne di potenza dellantenna.
! Non collegare mai il cavo blu/bianco al ter-
minale di alimentazione dellamplificatore di
potenza esterno. Inoltre, non collegarlo mai
al terminale di alimentazione dellantenna
automatica. In caso contrario, la batteria po-
trebbe scaricarsi o potrebbero verificarsi mal-
funzionamenti.
! Il cavo nero è la messa a terra. I cavi di
messa a terra di questa unità e di altre appa-
recchiature (soprattutto per i prodotti ad alta
tensione, quali amplificatori di potenza) de-
vono essere collegati separatamente. In caso
contrario, se scollegati accidentalmente, po-
trebbero provocare incendi o malfunziona-
menti.
Questa unità
3 45
21
Italiano
Funzionamento dellunità
35
Sezione
Installazione
It
02
03
Black plate (36,1)
1 Ingresso cavo di alimentazione
2 Uscita posteriore o del subwoofer
3 Ingresso antenna
4 Fusibile (10 A)
5 Ingresso telecomando cablato
È possibile collegare un adattatore per tele-
comando cablato (venduto a parte).
Cavo di alimentazione
1
3
3
2
4
4
5
5
6
6
b
8
9
7
a
e
d
c
1 Allingresso del cavo di alimentazione
2 A seconda del tipo di veicolo, la funzione di
3 e 5 potrebbe essere diversa. In questo
caso, accertarsi di collegare 4 a 5 e 6 a 3.
3 Giallo
Riserva (o accessorio)
4 Giallo
Collegare al terminale di alimentazione co-
stante 12 V.
5 Rosso
Accessorio (o riserva)
6 Rosso
Collegare al terminale controllato dallinter-
ruttore di accensione (12 V CC).
7 Collegare insieme i cavi dello stesso colore.
8 Nero (messa a terra telaio)
9 Blu/bianco
La posizione dei pin del connettore ISO sarà
diversa a seconda del tipo di veicolo. Collega-
re 9 e b quando il Pin 5 è del tipo controllo
antenna. In un altro tipo di veicolo, non colle-
gare mai 9 e b.
a Blu/bianco
Collegare al terminale di controllo del siste-
ma dellamplificatore di potenza (max.
300 mA 12 V CC).
b Blu/bianco
Collegare al terminale di controllo del relè
dellantenna automatica (max. 300 mA 12 V
CC).
c Giallo/nero
Se si utilizza un apparecchio dotato di funzio-
ne di silenziamento, collegare questo cavo al
cavo di silenziamento audio di tale apparec-
chio. In caso contrario, non collegare il cavo
di silenziamento audio.
d Cavi altoparlanti
Bianco: Anteriore sinistro +
Bianco/nero: Anteriore sinistro *
Grigio: Anteriore destro +
Grigio/nero: Anteriore destro *
Verde: Posteriore sinistro + o subwoofer +
Verde/nero: Posteriore sinistro * o subwoo-
fer *
Viola: Posteriore destro + o subwoofer +
Viola/nero: Posteriore destro * o subwoofer
*
e Connettore ISO
In alcuni veicoli, il connettore ISO potrebbe
essere diviso in due. In questo caso, accertar-
si di collegare entrambi i connettori.
Note
! Modifica delle impostazioni di menu iniziali
di questa unità. Vedere SP-P/O MODE (usci-
ta posteriore e impostazione pr e-out) a pagina
34.
Luscita subwoofer di questa unità è mono.
! Se si usa un subwoofer da 70 W (2 W), assicu-
rarsi di collegarlo ai fili viola e viola/nero di
questa unità. Non collegare niente ai fili
verde e verde/nero.
Amplificatore di poten za
(venduto a parte)
Eseguire questi collegamenti quando si usa
lamplificatore opzionale.
1
3
2
4
55
1 Telecomando sistema
Collegare al cavo Blu/bianco.
2 Amplificatore di potenza (venduto a parte)
3 Collegare con cavi RCA (venduti a parte)
4 Alluscita posteriore o del subwoofer
5 Altoparlanti posteriori o subwoofer
Installazione
Importante
! Controllare tutti i collegamenti e i sistemi
prima dellinstallazione finale.
! Non utilizzare componenti non approvati,
poiché potrebbero provocare malfunziona-
menti.
! Consultare il rivenditore se linstallazione ri-
chiede la trapanatura di fori o altre modifiche
del veicolo.
! Non installare questa unità se:
potrebbe interferire con il funzionamento del
veicolo.
potrebbe procurare lesioni al passeggero in
caso di arresto improvviso del veicolo.
! Se si surriscalda il laser a semiconduttore
potrebbe subire danni. Non installare questa
unità in luoghi soggetti a surriscaldamento,
come in prossimità delle bocchette dellim-
pianto di riscaldamento.
! Le prestazioni ottimali si ottengono quando
lunità viene installata con unangolazione in-
feriore a 60°.
60°
! Durante linstallazione, per assicurare la cor-
retta dissipazione del calore quando si utiliz-
za lunità, accertarsi di lasciare ampio spazio
dietro il pannello posteriore e avvolgere even-
tuali cavi allentati in modo che non ostrui-
scano le aperture.
5cmcm
Lasciare ampio spazio
5 cm
5 cm
Montaggio DIN anteriore/posteriore
Questa unità può essere installata correttamen-
te sia dalla posizione di montaggio anteriore, sia
dalla posizione di montaggio posteriore.
Durante linstallazione utilizzare componenti di-
sponibili in commercio.
Montaggio DIN anteriore
1 Inserire la fascetta di montaggio nel cru-
scotto.
Se lunità viene installata in uno spazio poco
profondo, utilizzare la fascetta di montaggio for-
nita. Se dietro lunità vi è spazio sufficiente, uti-
lizzare la fascetta di montaggio fornita con il
veicolo.
Installazione
36
Sezione
Installazione
It
03
Black plate (37,1)
2 Assicurare la fascetta di montaggio utiliz-
zando un cacciavite per piegare le linguette
metalliche (90°) in posizione.
1
2
1 Cruscotto
2 Fascetta di montaggio
# Accertarsi che lunità sia saldamente installata
in posizione. Uninstallazione instabile potrebbe cau-
sare salti audio o altri malfunzionamenti.
Montaggio DIN posteriore
1 Determinare la posizione appropriata, in
modo che i fori sulla staffa e sul lato delluni-
corrispondano.
2 Serrare due viti su ciascun lato.
1
2
3
1 Vite autofilettante (5 mm × 8 mm)
2 Staffa di montaggio
3 Cruscotto o console
Rimozione dellunità
1 Rimuovere la guarnizione.
1 Guarnizione
2 Linguetta intaccata
! La rimozione del frontalino permette di acce-
dere facilmente alla guarnizione.
! Quando si riapplica la guarnizione, spingere
il lato con la linguetta intaccata verso il
basso.
2 Inserire le chiavi di estrazione fornite su
entrambi i lati dellunità fino a che non scat-
tano in posizione.
3 Estrarre lunità dal cruscotto.
Rimozione e reinserimento del frontalino
È possibile rimuovere il frontalino per protegge-
re lunità dai furti.
Premere il tasto di rimozione e spingere il fronta-
lino verso lalto tirandolo verso lesterno.
Per ulteriori dettagli, vedere Rimozione del fronta-
lino per proteggere lunità dai furti e Reinserimen-
to del frontalino a pagina 30.
Risoluzione dei problemi
Sintomo Causa Azione
Il display
torna automa-
ticamente alla
visualizzazio-
ne normale.
Non è stata ese-
guita alcuna
operazione per
30 secondi.
Eseguire nuova-
mente loperazio-
ne.
Lintervallo di
riproduzione
ripetuta cam-
bia imprevedi-
bilmente.
A seconda del-
lintervallo di ri-
produzione ripe-
tuta, lintervallo
selezionato po-
trebbe cambiare
quando si sele-
ziona una car-
tella o un brano
diverso, o quan-
do si procede al-
lavanzamento
rapido/modalità
inversa.
Selezionare nuo-
vamente linter-
vallo di
riproduzione ripe-
tuta.
I brani di una
sottocartella
non vengono
riprodotti.
Non è possibile
riprodurre i
brani delle sot-
tocartelle se è
selezionata lop-
zione FLD (ripe-
tizione della
cartella).
Selezionare un
altro inter vallo di
riproduzione ripe-
tuta.
Quando cam-
bia il display,
viene visualiz-
zata unindi-
cazione NO
XXXX (ad
esempio, NO
TITLE).
Nel brano non è
incorporata al-
cuna informa-
zione di testo.
Modificare la vi-
sualizzazione o ri-
produrre un altro
brano/file.
Sintomo Causa Azione
Malfunziona-
mento dellu-
nità.
Ci sono inter-
ferenze.
Si sta utilizzan-
do un dispositi-
vo, ad esempio
un cellulare,
che trasmette
onde elettroma-
gnetiche in
prossimità del-
lunità.
Spostare il dispo-
sitivo elettrico che
causa interferen-
ze lontano dallu-
nità.
Messaggi di errore
Se si contatta il rivenditore o il Centro assistenza
Pioneer più vicino, accertarsi di annotare il mes-
saggio di errore.
Problemi comuni
Messaggio Causa Azione
AMP ERROR Lunità non fun-
ziona o lalto-
parlante non è
collegato corret-
tamente; è stato
attivato il circui-
to di protezione.
Controllare il col-
legamento degli
altoparlanti. Se il
messaggio non
scompare anche
dopo aver disatti-
vato e riattivato
lalimentazione,
contattare il riven-
ditore o la stazio-
ne assistenza
PIONEER più vici-
no.
Italiano
Installazione
37
Sezione
Informazioni supplementari
It
03
Black plate (38,1)
Lettore CD
Messaggio Causa Azione
ERROR-07,
11, 12, 17, 30
Il disco è spor-
co.
Pulire il disco.
Il disco è graf-
fiato.
Sostituire il disco.
ERROR-07,
10, 11, 12,
15, 17, 30,
A0
Si è verificato
un errore elettri-
co o meccani-
co.
Spegnere e ac-
cendere il motore
oppure passare a
una sorgente di-
versa e poi di
nuovo al lettore
CD.
ERROR-15 Il disco inserito
è vuoto.
Sostituire il disco.
ERROR-23 Il formato del
CD non è sup-
portato.
Sostituire il disco.
FORMAT
READ
A volte si verifi-
ca ritardo tra
quando la ripro-
duzione viene
avviata e quan-
do si inizia a
percepire il
suono.
Attendere che il
messaggio scom-
paia.
NO AUDIO Il disco inserito
non contiene
file riproducibili.
Sostituire il disco.
SKIPPED Il disco inserito
contiene file
protetti con tec-
nologia DRM.
Sostituire il disco.
PROTECT Tutti i file nel
disco inserito
sono protetti da
tecnologia
DRM.
Sostituire il disco.
Linee guida per luso corretto
Dischi e lettori
Utilizzare esclusivamente dischi che riportino uno
dei due seguenti loghi.
Utilizzare dischi da 12 cm. Non utilizzare dischi da
8 cm o adattatori per dischi da 8 cm.
Utilizzare esclusivamente dischi convenzionali,
completamente circolari. Non utilizzare dischi
dalla forma irregolare.
Nel vano dinserimento dei CD non inserire nien-
taltro che CD.
Non utilizzare dischi rotti, incrinati, piegati o altri-
menti danneggiati, in quanto potrebbero danneg-
giare il lettore.
Non è possibile riprodurre CD-R/RW non finalizza-
ti.
Non toccare la superficie registrata dei dischi.
Quando non si utilizzano, conservare i dischi nelle
rispettive custodie.
Non attaccare etichette, non scrivere e non appli-
care prodotti chimici sulla superficie dei dischi.
Per pulire un CD, passare delicatamente un
panno morbido sul disco procedendo dal centro
verso lesterno.
La formazione di condensa potrebbe temporanea-
mente limitare le prestazioni del lettore. In tal
caso, lasciarlo raggiungere una temperatura più
alta per circa unora. Inoltre, pulire i dischi che do-
vessero presentare condensa con un panno mor-
bido.
La riproduzione dei dischi potrebbe non essere
possibile a causa delle caratteristiche del disco,
del formato del disco, dellapplicazione di registra-
zione, dellambiente di riproduzione, delle condi-
zioni di conservazione e così via.
Le asperità della strada possono far interrompere
la riproduzione di un disco.
Prima di utilizzare i dischi, leggere le relative avver-
tenze.
Se si utilizzano dischi sui quali è possibile applica-
re etichette, controllare le istruzioni e le avvertenze
dei dischi. Linserimento e lespulsione potrebbe
non riuscire, a seconda dei dischi. Luso di dischi
di questo tipo potrebbe danneggiare questa unità.
Non affiggere sui dischi etichette o altri materiali
disponibili in commercio.
! I dischi potrebbero deformarsi e non sarà più
possibile riprodurli.
! Le etichette potrebbero staccarsi durante la ri-
produzione, impedendo lespulsione dei di-
schi. Ciò potrebbe danneggiare questa unità.
DualDisc
I supporti DualDisc sono dischi con due lati: un
CD registrabile per laudio su un lato e un DVD re-
gistrabile per i video sullaltro lato.
Poiché il lato CD dei DualDisc non è fisicamente
compatibile con gli standard CD generali, potreb-
be non essere possibile riprodurre il lato CD con
questa unità.
Il caricamento e lespulsione frequenti di un
DualDisc, possono provocare la presenza di graffi
sul disco. Graffi profondi possono determinare
problemi di riproduzione sullunità. In alcuni casi,
il DualDisc potrebbe rimanere bloccato nel vano
di inserimento disco e non essere espulso. Per
prevenire questi inconvenienti, si consiglia di non
utilizzare DualDisc con questa unità.
Fare riferimento alle informazioni fornite dal pro-
duttore del disco per informazioni dettagliate sui
DualDisc.
Compatibilità audio compressa
WMA
Estensione file: .wma
Velocità in bit: da 48 kbps a 320 kbps (CBR), da
48 kbps a 384 kbps (VBR)
Frequenza di campionamento: 32 kHz, 44,1 kHz,
48 kHz
Compatibilità Windows Media Audio Professional,
Lossless, Voice/DRM Stream/Stream con video:
non compatibile
MP3
Estensione file: .mp3
Velocità in bit: da 8 kbps a 320 kbps (CBR), VBR
Frequenza di campionamento: da 8 kHz a 48 kHz
(32 kHz, 44,1 kHz, 48 kHz per lenfatizzazione)
Versioni tag ID3 compatibili: 1.0, 1.1, 2.2, 2.3, 2.4
(alla tag ID3 Versione 2.x viene data la priorità ri-
spetto alla Versione 1.x.)
Compatibilità lista di riproduzione m3u: non com-
patibile
Compatibilità MP3i (MP3 interattivo), mp3 PRO:
non compatibile
Informazioni supplementari
38
Appendice
Informazioni supplementari
It
Black plate (39,1)
WAV
Estensione file: .wav
Bit di quantizzazione lineare: 8 e 16 (LPCM), 4 (MS
ADPCM)
Frequenza di campionamento: da 16 kHz a 48 kHz
(LPCM), 22,05 kHz e 44,1 kHz (MS ADPCM)
Informazioni supplementari
Per i nomi dei file (incluse le estensioni) o i nomi
delle cartelle, è possibile visualizzare esclusiva-
mente i primi 32 caratteri.
Il testo cirillico da visualizzare su questa unità
deve essere codificato con uno dei seguenti set di
caratteri:
! Unicode (UTF-8, UTF-16)
! Un set di caratteri diverso da Unicode utilizzato
in ambiente Windows e impostato come cirilli-
co nellimpostazione multilingue
A seconda dellapplicazione utilizzata per codifica-
re i file WMA, questa unità potrebbe non funziona-
re correttamente.
Disco
Gerarchia delle cartelle riproducibili: fino a otto li-
velli (una gerarchia pratica non dovrebbe prevede-
re più di due livelli.)
Cartelle riproducibili: fino a 99
File riproducibili: fino a 999
File system: ISO 9660 di livello 1 e 2, Romeo, Joliet
Riproduzione multi-sessione: compatibile
Trasferimento dati con scrittura a pacchetti: non
compatibile
Indipendentemente dalla durata degli intervalli
vuoti tra i brani della registrazione originale, i di-
schi contenenti file audio compresso verranno ri-
prodotti con una breve pausa tra i brani.
ATTENZIONE
Non lasciare dischi in luoghi esposti ad alte
temperature.
Riproduzione in sequenza
dei file audio
Con questa unità, lutente non può assegnare i
numeri alle cartelle e specificare sequenze di ri-
produzione.
Esempio di gerarchia
1
2
3
4
5
6
01
02
03
04
05
Livello 1 Livello 2 Livello 3 Livello 4
: cartella
: file audio com-
presso
da 01 a 05: numero
della cartella
da 1 a 6: sequenza
di riproduzione
Disco
La sequenza di selezione delle cartelle o altre
operazioni potrebbero risultare differenti, a se-
conda del software utilizzato per la codifica o la
scrittura.
Tabella dei caratteri cirillici
D: C D: C D: C D: C D: C
: А : Б : В : Г : Д
: Е, Ё : Ж : З : И, Й : К
: Л : М : Н : О : П
: Р : С : Т : У : Ф
: Х : Ц : Ч
: Ш,
Щ
: Ъ
: Ы : Ь : Э : Ю : Я
D: Display C: Carattere
Copyright e marchi registrati
iTunes
Apple ed iTunes sono marchi di fabbrica di
Apple Inc., registrati negli Stati Uniti ed in altri
Paesi.
MP3
La fornitura di questo prodotto prevede il trasfe-
rimento di una licenza esclusivamente per uso
privato, non-commerciale e non prevede la con-
cessione di una licenza, implica qualsiasi di-
ritto a utilizzare questo prodotto in qualsiasi
trasmissione in diretta commerciale (ovvero,
che generi profitti) terrestre, via satellite, cavo e/
o tramite altro mezzo, trasmissioni/diffusioni tra-
mite Internet, Intranet e/o altre reti o in altri si-
stemi elettronici di distribuzione di contenuti,
come applicazioni di trasmissione audio a paga-
mento o audio-on-demand. Per tali usi è neces-
saria una licenza specifica. Per dettagli, visitare
http://www.mp3licensing.com.
WMA
Windows Media è un marchio di fabbrica o mar-
chio di fabbrica depositato della Microsoft
Corporation negli Stati Uniti ed in altri paesi.
Questo prodotto include tecnologie di proprietà
della Microsoft Corporation e non è utilizzbile
senza licenza della Microsoft Licensing, Inc.
Italiano
Informazioni supplementari
39
Appendice
Informazioni supplementari
It
Black plate (40,1)
Dati tecnici
Generali
Alimentazione .................. 14,4 V di c.c. (variazioni con-
sentite da 10,8 V a 15,1 V)
Messa a terra ................... Negativa
Consumo massimo .......... 10,0 A
Dimensioni (L × A × P):
DIN
Unità principale
..................... 178mm × 50mm ×
165 mm
Pannello anteriore
..................... 188mm × 58mm ×
16 mm
D
Unità principale
..................... 178mm × 50mm ×
165 mm
Pannello anteriore
..................... 170mm × 46mm ×
16 mm
Peso ................................ 1 kg
Audio
Potenza duscita massima
................................... 50 W × 4
70 W × 1/2 W (per il subwoo-
fer)
Potenza duscita continua
................................... 22W × 4 (da 50 Hz a
15 000 Hz, 5% THD, carico 4 W,
entrambi i canali)
Impedenza di carico ......... 4 W (variazioni consentite da
4 W a8W)
Livello massimo di uscita
................................... 2,0V
Contorno della sonorità .... +10dB (a 100Hz), +6,5 dB (a
10 kHz) (volume: 30 dB)
Equalizzatore (equalizzatore grafico a 5 bande):
Frequenza ................. 80Hz/250 Hz/800 Hz/
2,5 kHz/8 kHz
Gamma di equalizzazione
............................ ±12 dB (a passi di 2 dB)
Subwoofer (mono):
Frequenze ................. 50Hz/63 Hz/80 Hz/100 Hz/
125 Hz/160 Hz/200 Hz
Pendenza .................. 6 dB per ottava, 12 dB per
ottava
Guadagno ................. da +6dB a 24 dB
Fase .......................... Normale e invertita
Lettore CD
Sistema ........................... Sistema audio per compact
disc
Dischi utilizzabili .............. Compact disc
Rapporto segnale/rumore
................................... 94dB (a 1 kHz) (rete IEC-A)
Numero di canali ............. 2 (stereo)
Formato di decodifica MP3
................................... MPEG-1 & 2 Audio Layer 3
Formato di decodifica WMA
................................... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2ca-
nali audio)
(Windows Media Player)
Formato segnale WAV ...... PCM lineare & MS ADPCM
(Non compresso)
Sintonizzatore FM
Gamma di frequenze ........ da 87,5 MHz a 108,0 MHz
Sensibilità ........................ 9dBf (0,8 µV/75 W, mono, rap-
porto S/R: 30 dB)
Rapporto segnale/rumore
................................... 72dB (rete IEC-A)
Sintonizzatore MW
Gamma di frequenze ........ da 531 kHz a 1 602kHz
Sensibilità ........................ 25µV (rapporto S/R: 20 dB)
Rapporto segnale/rumore
................................... 62dB (rete IEC-A)
Sintonizzatore LW
Gamma di frequenze ........ da 153 kHz a 281 kHz
Sensibilità ........................ 28µV (rapporto S/R: 20 dB)
Rapporto segnale/rumore
................................... 62dB (rete IEC-A)
Nota
Caratteristiche tecniche e design sono soggetti
a eventuali modifiche senza preavviso.
Informazioni supplementari
40
Appendice
It
Black plate (41,1)
Italiano
41It
Black plate (42,1)
Gracias por haber adquirido este producto
PIONEER
Lea con detenimiento este manual antes de utili-
zar el producto por primera vez para que pueda
darle el mejor uso posible. Es muy importante
que lea y cumpla con la información que apare-
ce bajo los mensajes de ADVERTENCIA y
PRECAUCIÓN de este manual. Una vez leído,
guarde el manual en un lugar seguro y a mano
para poder consultarlo en el futuro.
Si desea deshacerse de este producto, no lo
mezcle con los residuos generales de su
hogar. De conformidad con la legislación vi-
gente, existe un sistema de recogida distinto
para los productos electrónicos que requieren
un procedimiento adecuado de tratamiento,
recuperación y reciclado.
Las viviendas privadas en los estados miembros
de la UE, en Suiza y Noruega pueden devolver
gratuitamente sus productos electrónicos usa-
dos en los centros de recolección previstos o
bien en una tienda minorista (si adquieren un
producto similar nuevo).
En el caso de los países que no se han mencio-
nado en el párrafo anterior, póngase en contacto
con las autoridades locales a fin de conocer el
método de eliminación correcto.
Al actuar siguiendo estas instrucciones, se ase-
gurará de que el producto eliminado se someta
a los procesos de tratamiento, recuperación y
reciclaje necesarios, evitando de este modo
efectos potencialmente negativos en el entorno
y la salud humana.
Acerca de esta unidad
Las frecuencias del sintonizador de esta unidad
están asignadas para su uso en Europa Occi-
dental, Asia, Oriente Próximo, África y Oceanía.
El uso en otras áreas puede causar una recep-
ción deficiente. La función RDS (sistema de
datos de radio) opera solo en áreas con emiso-
ras de FM que trasmitan señales de RDS.
PRECAUCIÓN
Este aparato es un producto de láser de clase
1 clasificado como tal en Seguridad de pro-
ductos de láser, IEC 60825-1:2007.
PRODUCTO LASER CLASE 1
PRECAUCIÓN
! Evite que esta unidad entre en contacto con
líquidos, ya que puede producir una descar-
ga eléctrica. Además, el contacto con líqui-
dos puede causar daños en la unidad, humo
y recalentamiento.
! El CarStereo-Pass de Pioneer solo debe usar-
se en Alemania.
! Mantenga siempre el volumen lo suficiente-
mente bajo como para poder escuchar los
sonidos que provienen del exterior.
! Evite la exposición a la humedad.
! Si se desconecta o se descarga la batería,
todas las memorias preajustadas se borra-
rán.
Nota
Las operaciones se realizan incluso si se cance-
la el menú antes de confirmar.
En caso de problemas
Si esta unidad no funcionase correctamente,
póngase en contacto con su concesionario o
con el centro de servicio PIONEER autorizado
más cercano.
Antes de comenzar
42
Sección
Antes de comenzar
Es
01
Black plate (43,1)
Unidad principal
b c
5
8
1 2 3 4 6
a9d7
Parte Parte
1 h (expulsar) 8 BAND
2 SRC/OFF 9
(parte poste-
rior)/DIMMER (re-
ductor de luz)
3
MULTI-CONTROL
(M.C.)
a c/d
4
(lista) b 1/ a 6/
5 DISP c
Conector de en-
trada AUX (co-
nector estéreo de
3,5 mm)
6
Ranura de carga
de discos
d Botón de soltar
7
(ecualizador)
Indicaciones de la pantalla
21 3 75
9
4 6 8
a
Indicador Estado
1
(lista)
Se está utilizando la función
de la lista.
2
Sección de
información
secundaria
Muestra la información se-
cundaria.
3
TA (anun-
cios de trá-
fico)
La función TA está activada.
4
TP (identifi-
cación de
programa
de tráfico)
Una emisora TP está sintoni-
zada.
5
(recupera-
dor de soni-
do)
La función recuperación de
sonido está activada.
6 LOC
Sintonización por búsqueda
local activada.
7
(repeti-
ción)
La repetición de pista o carpe-
ta está activada.
8
(aleato-
rio)
La reproducción aleatoria
está activada.
9
Sección de
información
principal
! Sintonizador: banda y fre-
cuencia
! RDS: nombre del servicio
del programa, informa-
ción PTY y otro tipo de in-
formación de texto
! Lector de CD: tiempo de
reproducción transcurrido
e información de texto
a
Aparece cuando existe un
nivel, carpeta o menú inferior.
Menú de configuración
Una vez instalada la unidad, al poner en ON la
llave de encendido aparecerá el menú de confi-
guración.
Se pueden configurar las opciones del menú
que se describen a continuación.
1 Una vez instalada la unidad, gire la llave
de encendido hasta la posición ON.
Aparecerá SET UP.
2 Pulse M.C. para cambiar a YES.
# El menú de configuración desaparecerá si no se
utiliza la unidad durante 30 segundos.
# Si prefiere dejar la configuración para más tarde,
gire M.C. para cambiar a NO y púlselo para realizar
la selección.
Si selecciona NO, no podrá realizar cambios en el
menú de configuración.
3 Pulse M.C. para seleccionarlo.
4 Siga los siguientes pasos para ajustar el
menú:
Para avanzar a la siguiente opción del menú
debe confirmar primero su selección.
LANGUAGE (idiomas múltiples)
Esta unidad puede mostrar la información de
texto de un archivo de audio comprimido incluso
para aquella información integrada en inglés o
ruso.
! Si el idioma integrado y el idioma seleccionado
no coinciden, puede que la información de
texto no se muestre correctamente.
! Es posible que algunos caracteres no se visua-
licen correctamente.
1 Gire M.C. para seleccionar el ajuste deseado.
ENG (Inglés)РУС (Ruso)
2 Pulse M.C. para confirmar la selección.
CLOCK SET (ajuste del reloj)
1 Gire M.C. para ajustar el volumen.
2 Presione M.C. para seleccionar el minuto.
3 Gire M.C. para ajustar el minuto.
4 Pulse M.C. para confirmar la selección.
FM STEP (paso de sintonía de FM)
Normalmente, el paso de sintonía de FM emplea-
do en la sintonización por búsqueda es de 50 kHz.
Si la función AF o TA está activada, el paso de sin-
tonía cambia automáticamente a 100 kHz. Puede
que convenga ajustar el paso de sintonía a 50 kHz
si la función AF está activada.
! El paso de sintonía se mantiene en 50 kHz du-
rante la sintonización manual.
1 Gire M.C. para seleccionar el paso de sintonía
de FM.
50 (50 kHz)100 (100 kHz)
2 Pulse M.C. para confirmar la selección.
Aparecerá QUIT.
5 Para cerrar la configuración, gire M.C. y
seleccione YES.
# Si prefiere volver a cambiar la configuración, gire
M.C. para cambiar a NO y púlselo para realizar la se-
lección.
6 Pulse M.C. para seleccionarlo.
Notas
! Se pueden configurar las opciones del menú
desde el menú del sistema. Si desea más in-
formación sobre los ajustes, consulte Menú
del sistema en la página 47.
! Si desea cancelar el menú de configuración,
pulse SRC/OFF.
Funcionamiento básico
Importante
! Proceda con cuidado al retirar o colocar el
panel delantero.
Español
Utilización de esta unidad
43
Sección
Utilización de esta unidad
Es
02
Black plate (44,1)
! Evite someter el panel delantero a impactos
excesivos.
! Mantenga el panel delantero alejado de la
luz solar directa y no lo exponga a altas tem-
peraturas.
! Para evitar que el dispositivo o el interior del
vehículo sufran daños, retire todos los cables
o dispositivos conectados al panel delantero
antes de extraerlo.
Extracción del panel delantero para proteger la
unidad contra robo
1 Pulse el botón de soltar para liberar el panel
delantero.
2 Empuje el panel delantero hacia arriba (M)y
tire de él hacia usted (N).
3 Mantenga siempre el panel delantero que se
ha extraído en su medio de protección, como
la caja protectora.
Colocación del panel delantero
1 Deslice el panel hacia la izquierda.
Inserte las pestañas que hay en la parte iz-
quierda de la unidad principal dentro de las ra-
nuras del panel delantero.
2 Pulse el lado derecho del panel delantero
hasta que se asiente firmemente.
Si no logra encajar adecuadamente el panel
delantero a la unidad principal, colóquelo de
la forma correcta; no apriete ni use la fuerza
para encajarlo, ya que puede provocar daños
en el mismo o en la unidad principal.
Encendido de la unidad
1 Pulse SRC/OFF para encender la unidad.
Apagado de la unidad
1 Mantenga pulsado SRC/OFF hasta que se apa-
gue la unidad.
Selección de una fuente
1 Pulse SRC/OFF para desplazarse entre:
TUNER (sintonizador)CD (reproductor de
CD)AUX (AUX)
Ajuste del volumen
1 Gire M.C. para ajustar el volumen.
PRECAUCIÓN
Por motivos de seguridad, detenga el vehículo
antes de extraer el panel delantero.
Nota
Si el cable azul/blanco de esta unidad está co-
nectado al terminal de control del relé de la an-
tena automática del vehículo, la antena se
extenderá cuando se encienda el equipo. Para
retraer la antena, apague la fuente.
Operaciones del menú
utilizadas frecuentemente
Retorno a la visualización anterior
Para volver a la lista anterior (la carpeta de un
nivel superior)
1 Pulse
/DIMMER.
Retorno a la visualización normal
Acceso al menú principal
1 Pulse BAND.
Retorno a la visualización normal desde la lista
1 Pulse BAND.
Sintonizador
Funcionamiento básico
Selección de una banda
1 Pulse BAND hasta que se visualice la banda
deseada (FM1, FM2, FM3 para FM o MW/
LW).
Cambio de emisoras presintonizadas
1 Pulse c o d.
! Para utilizar esta función, seleccione PCH
(canal presintonizado) en SEEK. Para obtener
más información sobre la configuración, con-
sulte SEEK (ajuste tecla izquierda/derecha) en
la página siguiente.
Sintonización manual (paso a paso)
1 Pulse c o d.
! Para utilizar esta función, seleccione MAN
(sintonización manual) en SEEK. Para obtener
más información sobre la configuración, con-
sulte SEEK (ajuste tecla izquierda/derecha) en
la página siguiente.
Búsqueda
1 Mantenga pulsado c o d y luego suéltelo.
Se puede cancelar la sintonización por bús-
queda pulsando brevemente c o d.
Mientras mantiene pulsado c o d se pueden
saltar las emisoras. La sintonización por bús-
queda comienza inmediatamente después de
que suelte c o d.
Nota
Se puede activar y desactivar la función AF (bús-
queda de frecuencias alternativas) de esta uni-
dad; se debe desactivar la función AF para la
sintonización normal (consulte AF (búsqueda de
frecuencias alternativas) en la página siguiente).
Utilización de esta unidad
44
Sección
Utilización de esta unidad
Es
02
Black plate (45,1)
Almacenamiento y recuperación
de emisoras para cada banda
Uso de los botones de ajuste de
presintonías
1 Cuando encuentre la emisora que desee
almacenar en la memoria, pulse uno de los
botones de ajuste de presintonías (1/
a6/
) y manténgalo pulsado hasta que el nú-
mero de presintonía deje de parpadear.
2 Pulse uno de los botones de ajuste de
presintonías (1/
a6/ ) para seleccionar la
emisora deseada.
Cambio de la visualización
Selección de la información de texto deseada
1 Pulse DISP para desplazarse entre las siguien-
tes opciones:
! FREQUENCY (nombre del servicio de pro-
grama o frecuencia)
! BRDCST INFO (nombre del servicio de pro-
grama/información PTY)
! CLOCK (nombre de la fuente y reloj)
Notas
! Si no se puede adquirir el nombre del servi-
cio de programa en FREQUENCY, se visuali-
zará la frecuencia en su lugar. Si se detecta
el nombre del servicio de programa, se visua-
lizará el nombre del servicio de programa.
! BRDCST INFO la información de texto cam-
biará automáticamente.
! Dependiendo de la banda, puede cambiarse
la información de texto.
! Los elementos de información de texto pue-
den cambiar según la zona.
Uso de las funciones PTY
Se puede sintonizar una emisora utilizando la
información PTY (tipo de programa).
Búsqueda de una emisora RDS por información
PTY
Se pueden buscar programas de tipo general,
como los que se indican en el apartado siguiente.
Consulte esta página.
1 Pulse
(lista).
2 Gire M.C. para seleccionar el tipo de progra-
ma.
NEWS/INFOPOPULARCLASSICSOT-
HERS
3 Pulse M.C. para comenzar la búsqueda.
La unidad busca una emisora que transmita
ese tipo de programa, cuando la encuentra, se
visualiza el nombre del servicio de programa.
! Para cancelar la búsqueda, vuelva a pulsar
M.C.
! El programa de algunas emisoras puede
ser distinto al programa indicado por el
PTY transmitido.
! Si ninguna emisora está transmitiendo el
tipo de programa que busca, se visualizará
NOT FOUND durante unos dos segundos
y el sintonizador volverá a la emisora origi-
nal.
Lista PTY
NEWS/INFO (noticias e información)
NEWS (noticias), AFFAIRS (temas de actualidad),
INFO (información), SPORT (programas deporti-
vos), WEATHER (tiempo), FINANCE (finanzas)
POPULAR (popular)
POP MUS (música popular), ROCK MUS (rock),
EASY MUS (música ligera), OTH MUS (otras mú-
sicas), JAZZ (jazz), COUNTRY (música countr y),
NAT MUS (música nacional), OLDIES (música
antigua), FOLK MUS (música folclórica)
CLASSICS (clásicos)
L. CLASS (música clásica ligera), CLASSIC (clási-
ca)
OTHERS (otros)
EDUCATE (educación), DRAMA (drama), CULTU-
RE (cultura), SCIENCE (ciencia), VARIED (varieda-
des), CHILDREN (programas para niños), SOCIAL
(temas sociales), RELIGION (religión), PHONE IN
(entrada por teléfono), TOURING (viajes), LEISURE
(ocio), DOCUMENT (documentales)
Ajustes de funciones
1 Pulse M.C. para acceder al menú princi-
pal.
2 Gire M.C. para cambiar la opción de
menú y pulse para seleccionar FUNCTION.
3 Gire M.C. para seleccionar la función.
Una vez seleccionado, se pueden ajustar las si-
guientes funciones.
# Si se selecciona la banda MW/LW, solo estarán
disponibles BSM, LOCAL y SEEK.
BSM (memoria de las mejores emisoras)
BSM (memoria de las mejores emisoras) guarda
automáticamente las seis emisoras más fuertes
ordenadas por la intensidad de la señal.
1 Pulse M.C. para activar la función BSM.
Para cancelar, vuelva a pulsar M.C.
REGION (regional)
Cuando se usa la función AF, la función regional li-
mita la selección de las emisoras a aquellas que
transmiten programas regionales.
1 Pulse M.C. para activar o desactivar la función
regional.
LOCAL (sintonización por búsqueda local)
La sintonización por búsqueda local le permite
sintonizar solo las emisoras de radio con señales
lo suficientemente intensas como para asegurar
una correcta recepción.
1 Pulse M.C. para seleccionar el ajuste deseado.
FM: OFFLV1LV2LV3LV 4
MW/LW: OFFLV1 LV2
El ajuste de nivel superior solo permite recibir
las emisoras con las señales más intensas,
mientras que los ajustes más bajos permiten
recibir las emisoras con señales más débiles.
TA (espera por anuncio de tráfico)
1 Pulse M.C. para activar o desactivar la espera
por anuncio de tráfico.
AF (búsqueda de frecuencias alternativas)
1 Pulse M.C. para activar o desactivar la función
AF.
NEWS (interrupción por programa de noticias)
1 Pulse M.C. para activar o desactivar la función
NEWS.
SEEK (ajuste tecla izquierda/derecha)
Es posible asignar funciones a las teclas derecha
e izquierda de la unidad.
Seleccione MAN (sintonización manual) para
subir o bajar la frecuencia de forma manual o se-
leccione PCH (canales presintonizados) para cam-
biar entre los canales presintonizados.
1 Presione M.C. para seleccionar MAN o PCH.
Español
Utilización de esta unidad
45
Sección
Utilización de esta unidad
Es
02
Black plate (46,1)
CD/CD-R/CD-RW
Funcionamiento básico
Reproducción de un CD/CD-R/CD-RW
1 Inserte el disco en la ranura de carga de dis-
cos con el lado de la etiqueta hacia arriba.
Expulsión de un CD/CD-R/CD-RW
1 Pulse h.
Selección de una carpeta
1 Pulse 1/
o 2/ .
Selección de una pista
1 Pulse c o d.
Avance rápido o retroceso
1 Mantenga pulsado c o d.
! Al reproducir audio comprimido, no hay soni-
do durante el avance rápido o el retroceso.
Regreso a la carpeta raíz
1 Mantenga BAND pulsado.
Cambio entre audio comprimido y CD-DA
1 Pulse BAND.
Cambio de la visualización
Selección de la información de texto deseada
1 Pulse DISP para desplazarse entre las siguien-
tes opciones:
CD-DA
! ELAPSED TIME (número de pista y tiempo
de reproducción)
! CLOCK (nombre de la fuente y reloj)
! SPEANA (analizador de espectro)
CD-TEXT
! TRACK INFO (título de la pista/artista de la
pista/título del disco)
! ELAPSED TIME (número de pista y tiempo
de reproducción)
! CLOCK (nombre de la fuente y reloj)
! SPEANA (analizador de espectro)
MP3/WMA/WAV
! TRACK INFO (título de la pista/nombre del
artista/título del álbum)
! FILE INFO (nombre del fichero/nombre de
la carpeta)
! ELAPSED TIME (número de pista y tiempo
de reproducción)
! CLOCK (nombre de la fuente y reloj)
! SPEANA (analizador de espectro)
Notas
! TRACK INFO y FILE INFO la información de
texto cambiará automáticamente.
! Según la versión de iTunes utilizada para gra-
bar archivos MP3 en un disco u otro tipo de
archivo de medios, es posible que los textos
contenidos en el archivo de audio no se
muestren correctamente si su formato es in-
compatible.
! Los elementos de información de texto pue-
den cambiar según el tipo de medio.
Selección y reproducción de
archivos/pistas de la lista de
nombres
1 Pulse para cambiar al modo de lista
por nombre de archivo/pista.
2 Utilice M.C. para seleccionar el nombre
del archivo deseado (o de la carpeta).
Selección de un archivo o una carpeta
1 Gire M.C.
Reproducción
1 Tras seleccionar un archivo o una pista, pulse
M.C.
Visualización de una lista de los archivos (o las
carpetas) de la carpeta seleccionada
1 Tras seleccionar una carpeta, pulse M.C.
Reproducción de una canción de la carpeta selec-
cionada
1 Tras seleccionar una carpeta, mantenga pulsa-
do M.C.
Operaciones con botones especiales
Selección de un intervalo de repetición de repro-
ducción
1 Pulse 6/
para desplazarse entre las siguien-
tes opciones:
! ALL Repite todas las pistas
! ONE Repite la pista actual
! FLD Repite la carpeta actual
Reproducción de las pistas en orden aleatorio
1 Pulse 5/
para activar o desactivar la repro-
ducción aleatoria.
Las pistas de una gama de repetición seleccio-
nada se reproducen en orden aleatorio.
! Para cambiar de canciones durante la repro-
ducción aleatoria, pulse d para cambiar a la
pista siguiente; si se pulsa c se reiniciará la
reproducción de la pista actual desde el princi-
pio de la canción.
Pausa de la reproducción
1 Pulse 4/PAUSE para pausar o reanudar.
Mejora del audio comprimido y restauración del
sonido óptimo (Sound Retriever)
1 Pulse 3/S.Rtrv para desplazarse entre:
12OFF (desactivado)
1 es efectivo para tasas de compresión baja, y
2 para tasas de compresión alta.
Ajustes de funciones
1 Pulse M.C. para acceder al menú princi-
pal.
2 Gire M.C. para cambiar la opción de
menú y pulse para seleccionar FUNCTION.
Una vez seleccionado, se puede ajustar la fun-
ción de abajo.
Utilización de esta unidad
46
Sección
Utilización de esta unidad
Es
02
Black plate (47,1)
S.RTRV (recuperador de sonido)
Mejora automáticamente el audio comprimido y
restaura el sonido óptimo.
1 Pulse M.C. para seleccionar el ajuste deseado.
Para obtener más información, consulte Mejo-
ra del audio comprimido y restauración del soni-
do óptimo (Sound Retriever) en la página
anterior.
Ajustes de audio
1 Pulse M.C. para acceder al menú princi-
pal.
2 Gire M.C. para cambiar la opción de
menú y pulse para seleccionar AUDIO.
3 Gire M.C. para seleccionar la función de
audio.
Una vez seleccionado, se pueden ajustar las si-
guientes funciones de audio.
! FADER no está disponible cuando se selec-
ciona SUB.W/SUB.W en SP-P/O MODE. Para
más información, consulte SP-P/O MODE
(ajuste de la salida posterior y del preamplifica-
dor) en la página siguiente.
! SUB.W, SUB.W CTRL, HPF SETTING no están
disponibles cuando se selecciona
REAR/REAR en SP-P/O MODE. Para más in-
formación, consulte SP-P/O MODE (ajuste de
la salida posterior y del preamplificador) en la
página siguiente.
! SUB.W CTRL y HPF SETTING no están dispo-
nibles cuando se selecciona SUB.W en OFF.
Para más información, consulte SUB.W
(ajuste de subgraves activado/desactivado) en
esta página.
FADER (ajuste de ecualizador)
1 Pulse M.C. para mostrar el modo de ajuste.
2 Gire M.C. para ajustar el balance entre los alta-
voces delanteros/traseros.
BALANCE (ajuste del balance)
1 Pulse M.C. para mostrar el modo de ajuste.
2 Gire M.C. para ajustar el balance de los altavo-
ces izquierdo o derecho.
EQ SETTING (recuperación de ecualizador)
1 Pulse M.C. para mostrar el modo de ajuste.
2 Gire M.C. para seleccionar el ecualizador.
POWERFULNATURALVOCALCUS-
TOM1CUSTOM2FLATSUPER BASS
La banda y el nivel de ecualización se pueden
personalizar si se selecciona CUSTOM1 o
CUSTOM2.
Si selecciona CUSTOM1 o CUSTOM2, com-
plete los pasos que se describen más abajo. Si
selecciona otras opciones, pulse M.C. para
volver a la pantalla anterior.
! CUSTOM1 puede ajustarse por separado
para cada fuente.
! CUSTOM2 es una configuración comparti-
da que se utiliza para todas las fuentes.
3 Pulse M.C. para mostrar el modo de ajuste.
4 Pulse M.C. para desplazarse entre las siguien-
tes opciones:
Banda de ecualizaciónNivel de ecualización
5 Gire M.C. para seleccionar el ajuste deseado.
Banda de ecualización: 80HZ250HZ
800HZ2.5KHZ8KHZ
Nivel de ecualización: +6 a 6
! También puede cambiar el ecualizador pulsan-
do varias veces
.
LOUDNESS (sonoridad)
La sonoridad compensa las deficiencias en los in-
tervalos de frecuencias bajas y altas cuando se es-
cucha a un volumen bajo.
1 Pulse M.C. para seleccionar el ajuste deseado.
OFF (desactivado)LOW (bajo)MID
(medio)HI (alto)
SUB.W (ajuste de subgraves activado/desactiva-
do)
Esta unidad está equipada con una salida de sub-
graves que se puede activar o desactivar.
1 Pulse M.C. para seleccionar el ajuste deseado.
NOR (fase normal)REV (fase inversa)OFF
(subgraves desactivados)
SUB.W CTRL (ajuste de subgraves)
Solo las frecuencias más bajas que aquellas en el
intervalo seleccionado se generan por el altavoz
de subgraves.
1 Pulse M.C. para mostrar el modo de ajuste.
2 Pulse M.C. para desplazarse entre las siguien-
tes opciones:
Frecuencia de corteNivel de salidaNivel de
pendiente
Las tasas que se puedan ajustar parpadearán.
3 Gire M.C. para seleccionar el ajuste deseado.
Frecuencia de corte: 50HZ63HZ80HZ
100HZ125HZ160HZ200HZ
Nivel de salida: de 24 a +6
Nivel de pendiente: 6 12
BASS BOOST (intensificación de graves)
1 Pulse M.C. para mostrar el modo de ajuste.
2 Gire M.C. para seleccionar el nivel que desee.
Se visualiza 0 a +6 mientras se aumenta o dis-
minuye el nivel.
HPF SETTING (ajuste del filtro de paso alto)
Cuando no desee que se generen los sonidos
bajos del intervalo de frecuencias de salida de
subgraves a través de los altavoces delanteros o
traseros, active el filtro de paso alto (HPF). Solo
las frecuencias más altas que aquellas del interva-
lo seleccionado se generan a través de los altavo-
ces delanteros o traseros.
1 Pulse M.C. para mostrar el modo de ajuste.
2 Pulse M.C. para desplazarse entre las siguien-
tes opciones:
Frecuencia de corteNivel de pendiente
3 Gire M.C. para seleccionar el ajuste deseado.
Frecuencia de corte: OFF50HZ63HZ
80HZ100HZ125HZ160HZ200HZ
Nivel de pendiente: 6 12
SLA (ajuste del nivel de fuente)
SLA (ajuste del nivel de fuente) le permite ajustar
el nivel de volumen de cada fuente para evitar
cambios radicales en el volumen cuando se cam-
bia entre las fuentes.
! Los ajustes se basan en el nivel de volumen de
FM, que se mantiene inalterado.
! El nivel del volumen de MW/LW también se
puede ajustar con esta función.
! Al seleccionar FM como fuente, no se podrá
cambiar a SLA.
1 Pulse M.C. para mostrar el modo de ajuste.
2 Gire M.C. para ajustar el volumen de la fuente.
Gama de ajuste: de +4 a 4
Menú del sistema
Importante
PW SAVE (ahorro de energía) se cancela si la
batería del vehículo se desconecta, y se debe ac-
tivar de nuevo cuando se vuelva a conectar la
batería. Dependiendo de los métodos de cone-
xión, cuando PW SAVE (ahorro de energía) está
desactivado, la unidad puede seguir obteniendo
energía de la batería si la llave de encendido de
su vehículo no tiene posición ACC (accesorio).
Español
Utilización de esta unidad
47
Sección
Utilización de esta unidad
Es
02
Black plate (48,1)
1 Pulse M.C. para acceder al menú princi-
pal.
2 Gire M.C. para cambiar la opción de
menú y pulse para seleccionar SYSTEM.
3 Gire M.C. para seleccionar la función del
menú del sistema.
Una vez seleccionado, se pueden ajustar las si-
guientes funciones del menú de sistema.
LANGUAGE (idiomas múltiples)
Esta unidad puede mostrar la información de
texto de un archivo de audio comprimido incluso
para aquella información integrada en inglés o
ruso.
! Si el idioma integrado y el idioma seleccionado
no coinciden, puede que la información de
texto no se muestre correctamente.
! Es posible que algunos caracteres no se visua-
licen correctamente.
1 Gire M.C. para seleccionar el ajuste deseado.
ENG (Inglés)РУС (Ruso)
CLOCK SET (ajuste del reloj)
1 Pulse M.C. para mostrar el modo de ajuste.
2 Pulse M.C. para seleccionar el segmento de la
pantalla del reloj que desea ajustar.
HoraMinuto
3 Gire M.C. para ajustar el reloj.
12H/24H (anotación de la hora)
1 Pulse M.C. para seleccionar el ajuste deseado.
12H (reloj de 12 horas)24H (reloj de 24
horas)
AUTO PI (búsqueda PI automática)
La unidad puede buscar automáticamente una
emisora diferente con el mismo programa, incluso
durante la recuperación de emisoras presintoni-
zadas.
1 Pulse M.C. para activar o desactivar la función
de búsqueda PI automática.
AUX (entrada auxiliar)
Active este ajuste si utiliza un dispositivo auxiliar
conectado a esta unidad.
1 Pulse M.C. para activar o desactivar AUX.
MUTE MODE (modo de silencio)
El sonido proveniente de este sistema se silencia
o atenúa automáticamente cuando se recibe una
señal desde un equipo con función de silencia-
miento.
1 Pulse M.C. para mostrar el modo de ajuste.
2 Gire M.C. para seleccionar el ajuste deseado.
Se puede seleccionar cualquiera de las opcio-
nes de la lista siguiente:
! MUTE Silenciamiento
! 20dB ATT Atenuación (20dB ATT tiene
un efecto más potente que 10dB ATT)
! 10dB ATT Atenuación
PW SAVE (ahorro de energía)
La activación de esta función le permite reducir el
consumo de la batería.
! Cuando esta función está activada, la única
operación que se permite es el encendido de
la fuente.
1 Pulse M.C. para activar o desactivar el ahorro
de energía.
Cambio del ajuste del
atenuador de luz
Puede ajustar el brillo de la iluminación.
1 Pulse M.C. para acceder al menú princi-
pal.
2 Gire M.C. para visualizar ILLUMI y púlselo
para realizar la selección.
3 Pulse M.C. para seleccionar el ajuste de-
seado.
OFF (activado)ON (desactivado)
! También se puede cambiar la configuración
de atenuador de luz manteniendo pulsado
/DIMMER.
Menú inicial
1 Mantenga pulsado SRC/OFF hasta que se
apague la unidad.
2 Mantenga pulsado SRC/OFF hasta que
aparezca el menú principal en la pantalla.
3 Gire M.C. para cambiar la opción de
menú y pulse para seleccionar INITIAL.
4 Gire M.C. para seleccionar la función del
menú de inicio.
Una vez seleccionado, se pueden ajustar las si-
guientes funciones del menú inicial.
FM STEP (paso de sintonía de FM)
Normalmente, el paso de sintonía de FM emplea-
do en la sintonización por búsqueda es de 50 kHz.
Si la función AF o TA está activada, el paso de sin-
tonía cambia automáticamente a 100 kHz. Puede
que convenga ajustar el paso de sintonía a 50 kHz
si la función AF está activada.
! El paso de sintonía se mantiene en 50 kHz du-
rante la sintonización manual.
1 Pulse M.C. para seleccionar el paso de sinto-
nía de FM.
50 (50 kHz)100 (100 kHz)
SP-P/O MODE (ajuste de la salida posterior y del
preamplificador)
La salida de cables de altavoces traseros y la sali-
da RCA de esta unidad se puede usar para co-
nectar altavoces de gama completa o de
subgraves. Seleccione la opción adecuada para
su conexión.
1 Pulse M.C. para mostrar el modo de ajuste.
2 Gire M.C. para seleccionar el ajuste deseado.
Se puede seleccionar cualquiera de las opcio-
nes de la lista siguiente:
! REAR/SUB.W Seleccione cuando haya
conectado un altavoz de gama completa a
la salida de cables de altavoces traseros y
un subgrave a la salida RCA.
! SUB.W/SUB.W Seleccione cuando haya
conectado un subgrave directamente a la
salida de cables de altavoces traseros, sin
ningún amplificador auxiliar, y un subgrave
a la salida RCA.
! REAR/REAR Seleccione cuando exista
un altavoz de gama completa conectado a
la salida de cables de los altavoces trase-
ros y a la salida RCA.
Si hay un altavoz de gama completa conec-
tado a la salida de cables de los altavoces
traseros y la salida RCA no se utiliza, podrá
seleccionar REAR/SUB.W o REAR/REAR.
Menú del sistema
1 Mantenga pulsado SRC/OFF hasta que se
apague la unidad.
2 Mantenga pulsado SRC/OFF hasta que
aparezca el menú principal en la pantalla.
3 Gire M.C. para cambiar la opción de
menú y pulse para seleccionar SYSTEM.
Utilización de esta unidad
48
Sección
Utilización de esta unidad
Es
02
Black plate (49,1)
4 Gire M.C. para seleccionar la función del
menú del sistema.
Una vez seleccionado, se pueden ajustar las si-
guientes funciones del menú de sistema.
Para obtener más información, consulte Menú
del sistema en la página 47.
Uso de una fuente AUX
1 Inserte el miniconector estéreo en el co-
nector de entrada AUX.
2 Pulse SRC/OFF para seleccionar AUX
como fuente.
Nota
No se puede seleccionar AUX si no se activa el
ajuste auxiliar. Para obtener más información,
consulte AUX (entrada auxiliar) en la página an-
terior.
Cambio de la visualización
Selección de la información de texto deseada
1 Pulse DISP para desplazarse entre las siguien-
tes opciones:
! Nombre de la fuente
! Nombre de la fuente y reloj
Si aparece un display no
deseado
Desactive el display no deseado mediante los
pasos que se indican a continuación.
1 Pulse M.C. para acceder al menú princi-
pal.
2 Gire M.C. para cambiar la opción de
menú y pulse para seleccionar SYSTEM.
3 Gire M.C. para visualizar DEMO OFF y
púlselo para realizar la selección.
4 Pulse M.C. para cambiar a YES.
5 Pulse M.C. para seleccionarlo.
Conexiones
Importante
! Cuando esta unidad se instale en un ve-
hículo sin posición ACC (accesorio) en la
llave de encendido, el cable rojo se debe co-
nectar al terminal que pueda detectar la ope-
ración de la llave de encendido. De lo
contrario, puede descargarse la batería.
O
N
S
T
A
R
T
O
F
F
Posición ACC Sin posición ACC
! El uso de esta unidad en unas condiciones
distintas de las indicadas a continuación po-
dría causar incendios o fallos de funciona-
miento.
Vehículos con una batería de 12 voltios y co-
nexión a tierra negativa.
Altavoces con 50 W (valor de salida) y 4 W a
8 W (valor de impedancia).
! Para evitar cortocircuitos, sobrecalentamien-
to o fallos de funcionamiento, asegúrese de
seguir las siguientes instrucciones.
Desconecte el terminal negativo de la batería
antes de la instalación.
Asegure el cableado con pinzas para cables
o cinta adhesiva. Envuelva con cinta adhesiva
las partes en contacto con piezas metálicas
para proteger el cableado.
Mantenga los cables alejados de las partes
móviles, como la palanca de cambios y los
raíles de los asientos.
Coloque todos los cables alejados de lugares
calientes, como cerca de la salida del calefac-
tor.
No conecte el cable amarillo a la batería pa-
sándolo a través del orificio hasta el compar-
timiento del motor.
Cubra con cinta aislante los conectores de
cables que queden desconectados.
No acorte ningún cable.
Nunca corte el aislamiento del cable de ali-
mentación de esta unidad para compartir la
corriente con otros equipos. La capacidad de
corriente del cable es limitada.
Utilice un fusible con la intensidad nominal
indicada.
Nunca conecte el cable negativo de los alta-
voces directamente a tierra.
Nunca empalme los cables negativos de va-
rios altavoces.
! Cuando se enciende esta unidad, se emite
una señal de control a través del cable azul/
blanco. Conecte este cable al mando a dis-
tancia del sistema de un amplificador de po-
tencia externo o al terminal de control del
relé de la antena automática del vehículo
(máx. 300 mA 12 V cc). Si el vehículo posee
una antena integrada en el cristal del para-
brisas, conéctela al terminal de la fuente de
alimentación del amplificador de la antena.
! Nunca conecte el cable azul/blanco al termi-
nal de potencia de un amplificador de poten-
cia externo, ni al terminal de potencia de la
antena automática, de lo contrario, puede
descargarse la batería o producirse un fallo
de funcionamiento.
! El cable negro es el cable a tierra. Los cables
a tierra de esta unidad y de otros productos
(especialmente productos de alta tensión,
como amplificadores de potencia) se deben
conectar por separado, de lo contrario,
puede producirse un incendio o un fallo de
funcionamiento si se desconectan por acci-
dente.
Esta unidad
3 45
21
1 Entrada del cable de alimentación
Español
Utilización de esta unidad
49
Sección
Instalación
Es
02
03
Black plate (50,1)
2 Salida trasera o salida de subgraves
3 Entrada de la antena
4 Fusible (10 A)
5 Entrada remota conectada
Es posible conectar un adaptador de mando
a distancia físicamente conectado (se vende
por separado).
Cable de alimentación
1
3
3
2
4
4
5
5
6
6
b
8
9
7
a
e
d
c
1 A la toma del cable de alimentación
2 Según el tipo de vehículo, las funciones de
3 y 5 pueden ser diferentes. En este caso,
conecte 4 a 5 y 6 a 3.
3 Amarillo
Reserva (o accesorio)
4 Amarillo
Conectar al terminal de alimentación cons-
tante de 12 V.
5 Rojo
Accesorio (o reserva)
6 Rojo
Conectar al terminal controlado por la llave
de encendido (12 V CC).
7 Conecte entre los cables del mismo color.
8 Negro (Toma de tierra del chasis)
9 Azul/blanco
La posición de las patillas del conector ISO
será diferente según el tipo de vehículo. Co-
necte 9 y b cuando la patilla 5 sea del tipo
control de antena. En otro tipo de vehículo,
no se deben conectar nunca 9 y b.
a Azul/blanco
Conectar al terminal de control del sistema
del amplificador de potencia (máx. 300 mA
12 V CC).
b Azul/blanco
Conectar al terminal de control del relé de la
antena automática (máx. 300 mA 12 V CC).
c Amarillo/negro
Si utiliza un equipo con función de silencia-
miento, conecte este cable con el cable de si-
lenciamiento de audio de ese equipo. En
caso contrario, mantenga el cable de silen-
ciamiento de audio sin ninguna conexión.
d Cables de altavoces
Blanco: delantero izquierdo +
Blanco/negro: delantero izquierdo *
Gris: delantero derecho +
Gris/negro: delantero derecho *
Verde: trasero izquierdo + o altavoz de sub-
graves +
Verde/negro: trasero izquierdo * o altavoz de
subgraves *
Violeta: trasero derecho + o altavoz de sub-
graves +
Violeta/negro: trasero derecho * o altavoz
de subgraves *
e Conector ISO
En algunos vehículos, el conector ISO puede
estar dividido en dos. En este caso, asegúre-
se de conectar los dos conectores.
Notas
! Cambie el menú inicial de esta unidad. Con-
sulte SP-P/O MODE (ajuste de la salida pos-
terior y del preamplificador) en la página 48.
La salida de graves de esta unidad es mo-
noaural.
! Al usar un altavoz de subgraves de 70 W
(2 W), conecte el mismo a los cables violeta y
violeta/negro de esta unidad. No conecte
nada al cable verde ni al verde/negro.
Amplificador de potencia (se
vende por separado)
Realice estas conexiones cuando utilice el am-
plificador opcional.
1
3
2
4
55
1 Control remoto del sistema
Conexión a cable azul/blanco.
2 Amplificador de potencia (se vende por sepa-
rado)
3 Conectar con cables RCA (se venden por se-
parado)
4 A la salida trasera o salida de subgraves
5 Altavoz trasero o altavoz de subgraves
Instalación
Importante
! Compruebe todas las conexiones y sistemas
antes de la instalación final.
! No utilice piezas no autorizadas, ya que pue-
den causar fallos de funcionamiento.
! Consulte a su distribuidor si para la instala-
ción es necesario taladrar orificios o hacer
otras modificaciones al vehículo.
! No instale esta unidad en un lugar donde:
Pueda interferir con el manejo del vehículo.
Pueda lesionar a un pasajero como conse-
cuencia de un frenazo brusco.
! El láser semiconductor se dañará si se sobre-
calienta. Instale esta unidad alejada de
zonas que alcancen altas temperaturas,
como cerca de la salida del calefactor.
! Se logra un rendimiento óptimo si la unidad
se instala en un ángulo inferior a 60°.
60°
! Cuando instale, para asegurar la dispersión
apropiada del calor durante el uso de esta
unidad, asegúrese de dejar un amplio espa-
cio por detrás del panel trasero y enrolle los
cables sueltos de modo que no bloqueen las
aberturas de ventilación.
Deje un amplio espacio
5 cm
5 cm
Montaje delantero/posterior de DIN
Esta unidad puede instalarse correctamente
tanto si se realiza una instalación frontal o trase-
ra.
En la instalación, emplee piezas disponibles en
el mercado.
Montaje delantero DIN
1 Inserte el manguito de montaje en el sal-
picadero.
Si realiza la instalación en un espacio poco pro-
fundo, utilice el manguito de montaje suminis-
trado. Si hay suficiente espacio, utilice el
manguito de montaje que venía con el vehículo.
Instalación
50
Sección
Instalación
Es
03
Black plate (51,1)
2 Fije el manguito de montaje utilizando
un destornillador para doblar las pestañas
metálicas (90°) y colocarlas en su lugar.
1
2
1 Salpicadero
2 Manguito de montaje
# Asegúrese de que la unidad esté firmemente ins-
talada en su lugar. Una instalación inestable puede
causar saltos en el audio o un mal funcionamiento
de la unidad.
Montaje trasero DIN
1 Determine la posición correcta, de modo
que los orificios del soporte y del lateral de
la unidad coincidan.
2 Apriete los dos tornillos en cada lado.
1
2
3
1 Tornillo con rosca cortante (5 mm × 8 mm)
2 Carcasa
3 Salpicadero o consola
Extracción de la unidad
1 Retire el anillo de guarnición.
1 Anillo de guarnición
2 Pestaña con muesca
! Libere el panel delantero para acceder más
fácilmente al anillo de guarnición.
! Al volver a colocar el anillo de guarnición,
oriente hacia abajo la pestaña con muesca.
2 Inserte en ambos lados de la unidad las
llaves de extracción provistas hasta que se
escuche un ligero chasquido.
3 Extraiga la unidad del salpicadero.
Retirada y colocación del panel delantero
Puede extraer el panel delantero para proteger
la unidad contra robo.
Pulse el botón de soltar, empuje el panel delan-
tero hacia arriba y tire de él hacia sí.
Para obtener más información, consulte Extrac-
ción del panel delantero para proteger la unidad
contra robo y Colocación del panel delantero en la
página 44.
Solución de problemas
Síntoma Causa Resolución
La pantalla
vuelve auto-
máticamente
a la visualiza-
ción normal.
No ha realizado
ninguna opera-
ción en aproxi-
madamente 30
segundos.
Realice la opera-
ción de nuevo.
El intervalo de
repetición de
reproducción
cambia de
manera ines-
perada.
Dependiendo
del intervalo de
repetición de re-
producción, el
intervalo selec-
cionado puede
cambiar cuando
se selecciona
otra carpeta o
pista o cuando
se utilice el
avance rápido/
retroceso.
Seleccione de
nuevo el intervalo
de repetición de
reproducción.
No se repro-
duce una sub-
carpeta.
No se pueden
reproducir las
subcarpetas
cuando se se-
lecciona FLD
(repetición de
carpeta).
Seleccione otro
intervalo de repe-
tición de repro-
ducción.
NO XXXX
aparece cuan-
do se cambia
una pantalla
(NO TITLE,
por ejemplo).
No hay informa-
ción de texto in-
corporada.
Cambie la panta-
lla o reproduzca
otra pista/archivo.
La unidad no
funciona co-
rrectamente.
Hay una inter-
ferencia.
Está usando un
dispositivo,
como un teléfo-
no móvil, que
transmite ondas
eléctricas cerca
de la unidad.
Aleje de la unidad
los dispositivos
eléctricos que
puedan estar cau-
sando interferen-
cias.
Mensajes de error
Anote el mensaje de error antes de contactar
con su concesionario o con el servicio técnico
oficial de Pioneer más cercano.
Comunes
Mensaje Causa Resolución
AMP ERROR La unidad no
funciona o la
conexión de los
altavoces es in-
correcta; se ac-
tiva el circuito
de protección.
Compruebe la co-
nexión de los alta-
voces. Si el
mensaje no desa-
parece aun des-
pués de apagar y
volver a encender
el motor, contacte
con su distribui-
dor o con el Servi-
cio técnico oficial
Pioneer.
Reproductor de CD
Mensaje Causa Resolución
ERROR-07,
11, 12, 17, 30
El disco está
sucio.
Limpie el disco.
El disco está ra-
yado.
Sustituya el disco.
ERROR-07,
10, 11, 12,
15, 17, 30,
A0
Se ha producido
un error eléctri-
co o mecánico.
Coloque la llave
de encendido del
automóvil en la
posición de de-
sactivación y
luego pase de
nuevo a activa-
ción, o cambie a
una fuente dife-
rente y, a conti-
nuación, vuelva a
activar el repro-
ductor de CD.
Español
Instalación
51
Sección
Información adicional
Es
03
Black plate (52,1)
Mensaje Causa Resolución
ERROR-15 El disco inser-
tado aparece en
blanco.
Sustituya el disco.
ERROR-23 Formato de CD
no compatible.
Sustituya el disco.
FORMAT
READ
A veces se pro-
duce un retraso
entre el comien-
zo de la repro-
ducción y la
emisión del so-
nido.
Espere hasta que
el mensaje desa-
parezca y oiga so-
nido.
NO AUDIO El disco inser-
tado no contie-
ne archivos
reproducibles.
Sustituya el disco.
SKIPPED El disco inser-
tado contiene
archivos prote-
gidos con DRM.
Sustituya el disco.
PROTECT Todos los archi-
vos del disco in-
sertado tienen
DRM integrado.
Sustituya el disco.
Pautas para el manejo
Discos y reproductor
Utilice únicamente discos que tengan uno de
estos dos logotipos:
Utilice discos de 12 cm. No utilice discos de 8 cm
o un adaptador de discos de 8 cm.
Utilice solo discos convencionales y completa-
mente circulares. No use discos con formas irre-
gulares.
No coloque ningún otro elemento que no sea un
CD en la ranura de carga de CD.
No use discos rotos, astillados, deformados o da-
ñados, ya que pueden causar daños al reproduc-
tor.
No es posible reproducir discos CD-R/RW no fina-
lizados.
No toque la superficie grabada de los discos.
Cuando no utilice los discos, guárdelos en sus
cajas.
No fije etiquetas, no escriba ni aplique sustancias
químicas en la superficie de los discos.
Para limpiar un CD, pásele un paño suave desde
el centro hacia afuera.
La condensación puede afectar temporalmente al
rendimiento del reproductor. Deje de usarlo duran-
te una hora aproximadamente para que se adapte
a la temperatura más cálida. Además, si los dis-
cos tienen humedad, séquelos con un paño
suave.
Quizá no pueda reproducir algunos discos debido
a sus características, formato, programas graba-
dos, entorno de reproducción, condiciones de al-
macenamiento u otras causas.
Las vibraciones en las carreteras pueden inte-
rrumpir la reproducción de un disco.
Lea las advertencias de los discos antes de utili-
zarlos.
Al usar discos de superficie imprimible para eti-
quetas, lea primero las instrucciones y las adver-
tencias de los discos. Es posible que algunos
discos no puedan insertarse ni expulsarse. La utili-
zación de este tipo de discos puede dañar el equi-
po.
No pegue etiquetas compradas por separado ni
otro tipo de material a los discos.
! Los discos podrían combarse y no podrán re-
producirse.
! Las etiquetas pueden despegarse durante la
reproducción, evitando la expulsión del disco y
causando de este modo daños en el equipo.
DualDisc
Los discos DualDisc (discos dobles) son discos de
dos caras que incluyen un CD grabable de audio
en una cara y un DVD grabable de vídeo en la otra
cara.
Debido a que la cara del CD de los discos
DualDisc no es físicamente compatible con el es-
tándar general de CD, es posible que no se pueda
reproducir la cara del CD en esta unidad.
La carga y expulsión frecuente de un disco
DualDisc puede producir ralladuras en el disco;
las ralladuras graves pueden producir problemas
de reproducción en esta unidad. En algunos
casos, un DualDisc puede atascarse en la ranura
de carga del disco y no se expulsará, para evitarlo,
recomendamos que no utilice DualDisc en esta
unidad.
Consulte la información del fabricante del disco
para obtener más información sobre DualDisc.
Compatibilidad con audio
comprimido
WMA
Extensión de archivo: .wma
Velocidad de grabación: de 48 kbps a 320 kbps
(CBR) y de 48 kbps a 384 kbps (VBR)
Frecuencia de muestreo: 32 kHz, 44,1 kHz, 48 kHz
Windows Media Audio Professional, Lossless,
Voice/DRM Stream/Stream con vídeo: no compati-
ble
MP3
Extensión de archivo: .mp3
Velocidad de grabación: de 8 kbps a 320 kbps
(CBR), VBR
Frecuencia de muestreo: de 8 kHz a 48 kHz
(32 kHz, 44,1 kHz, 48 kHz para énfasis)
Versiones de etiqueta ID3 compatibles: 1.0, 1.1,
2.2, 2.3, 2.4 (la etiqueta ID3 versión 2.x tiene priori-
dad sobre la versión 1.x)
Lista de reproducción M3u: no compatible
MP3i (MP3 interactivo), mp3 PRO: no compatible
Información adicional
52
Apéndice
Información adicional
Es
Black plate (53,1)
WAV
Extensión de archivo: .wav
Bits de cuantificación: 8 y 16 (LPCM), 4 (MS
ADPCM)
Frecuencia de muestreo: 16 kHz a 48 kHz (LPCM),
22,05 kHz y 44,1 kHz (MS ADPCM)
Información complementaria
Solo se pueden visualizar los primeros 32 caracte-
res como nombre de archivo (incluida la exten-
sión) o nombre de carpeta.
Los textos en ruso que se visualizarán en esta uni-
dad se deben codificar con los siguientes conjun-
tos de caracteres:
! Unicode (UTF-8, UTF-16)
! Los conjuntos de caracteres distintos de Uni-
code que se usan en el entorno Windows y
que están ajustados en ruso en la configura-
ción de idiomas múltiples.
Esta unidad puede no funcionar correctamente,
según la aplicación utilizada para codificar archi-
vos WMA.
Disco
Jerarquía de carpetas reproducibles: hasta ocho
niveles (una jerarquía práctica de carpetas tiene
menos de dos niveles).
Carpetas reproducibles: hasta 99
Archivos reproducibles: hasta 999
Sistema de archivos: ISO 9660 Nivel 1 y 2, Romeo,
Joliet
Reproducción multisesión: compatible
Transferencia de datos en formato Packet Write:
no compatible
Independientemente de la longitud de la seccio-
nes en blanco que haya entre las canciones de la
grabación original, los discos de audio comprimi-
dos se reproducirán con una breve pausa entre
cada canción.
PRECAUCIÓN
No deje los discos en lugares donde puedan
verse sometidos a altas temperaturas.
Secuencia de archivos de audio
El usuario no puede asignar números de carpe-
ta ni especificar secuencias de reproducción
con esta unidad.
Ejemplo de una jerarquía
1
2
3
4
5
6
01
02
03
04
05
Nivel 1 Nivel 2 Nivel 3 Nivel 4
: carpeta
: archivo de audio
comprimido
01 a 05: número de
carpeta
1 a 6: secuencia
de reproducción
Disco
La secuencia de selección de carpetas u otras
operaciones pueden diferir, dependiendo del
software de codificación o escritura.
Tabla de caracteres rusos
D: C D: C D: C D: C D: C
: А : Б : В : Г : Д
: Е, Ё : Ж : З : И, Й : К
: Л : М : Н : О : П
: Р : С : Т : У : Ф
: Х : Ц : Ч
: Ш,
Щ
: Ъ
: Ы : Ь : Э : Ю : Я
D: Visualización C: Carácter
Copyright y marcas registradas
iTunes
Apple e iTunes son marcas comerciales de
Apple Inc., registradas en los EE.UU. y en otros
países.
MP3
La venta de este producto solo otorga una licen-
cia para su uso privado, no comercial. No otorga
ninguna licencia ni concede ningún derecho a
utilizar este producto en transmisiones comer-
ciales (es decir, lucrativas) en tiempo real (te-
rrestres, vía satélite, por cable y/o por cualquier
otro medio), transmisiones/streaming por Inter-
net, intranets u otras redes o en otros sistemas
de distribución de contenido electrónico, como
por ejemplo, aplicaciones de pago por escucha
(pay-audio) o audio bajo demanda (audio-on-de-
mand). Se necesita una licencia independiente
para su uso comercial. Para obtener más infor-
mación, visite
http://www.mp3licensing.com.
WMA
Windows Media es una marca registrada o una
marca de fábrica de Microsoft Corporation en
los Estados Unidos y/u otros países.
Este producto incluye tecnología propiedad de
Microsoft Corporation, y no se puede usar ni dis-
tribuir sin una licencia de Microsoft Licensing,
Inc.
Español
Información adicional
53
Apéndice
Información adicional
Es
Black plate (54,1)
Especificaciones
Generales
Fuente de alimentación .... 14,4 V cc (10,8 V a 15,1 V per-
misible)
Sistema de derivación a tierra
................................... Tipo negativo
Consumo máximo de corriente
................................... 10,0 A
Dimensiones (An × Al × Pr):
DIN
Bastidor ............. 178 mm × 50mm ×
165 mm
Cara anterior ...... 188 mm × 58mm ×
16 mm
D
Bastidor ............. 178 mm × 50mm ×
165 mm
Cara anterior ...... 170 mm × 46mm ×
16 mm
Peso ................................ 1 kg
Audio
Potencia de salida máxima
................................... 50 W × 4
70 W × 1/2 W (para altavoz de
subgraves)
Potencia de salida continua
................................... 22W × 4 (50Hz a 15000Hz,
5% THD, 4 W de carga, ambos
canales activados)
Impedancia de carga ....... 4 W (4 W a8W permisibles)
Nivel de salida máxima del preamplificador
................................... 2,0V
Contorno de sonoridad ..... +10 dB (100 Hz), +6,5 dB
(10 kHz) (volumen: 30 dB)
Ecualizador (ecualizador gráfico de 5 bandas):
Frecuencia ................ 80Hz/250 Hz/800 Hz/
2,5 kHz/8 kHz
Gama de ecualización
............................ ±12 dB (paso de 2 dB )
Altavoz de subgraves (mono):
Frecuencia ................ 50Hz/63 Hz/80 Hz/100 Hz/
125 Hz/160 Hz/200 Hz
Pendiente ................. 6 dB/oct, 12 dB/oct
Ganancia .................. +6dB a 24 dB
Fase .......................... Normal/Inversa
Reproductor de CD
Sistema ........................... Sistema de audio de discos
compactos
Discos utilizables ............. Disco compacto
Relación de señal a ruido
................................... 94dB (1kHz) (red IEC-A)
Número de canales .......... 2 (estéreo)
Formato de decodificación MP3
................................... MPEG-1 & 2 Audio Layer 3
Formato de decodificación WMA
................................... Ver. 7, 7.1, 8, 9, 10, 11, 12
(audio 2 canales)
(Windows Media Player)
Formato de señal WAV ..... PCM lineal & MS ADPCM
(No comprimido)
Sintonizador de FM
Intervalo de frecuencias ... de 87,5 MHz a 108,0 MHz
Sensibilidad utilizable ...... 9 dBf (0,8 µV/75 W, mono,
señal/ruido: 30 dB)
Relación de señal a ruido
................................... 72dB (red IEC-A)
Sintonizador de MW
Intervalo de frecuencias ... de 531 kHz a 1 602 kHz
Sensibilidad utilizable ...... 25µV (señal/ruido: 20 dB)
Relación de señal a ruido
................................... 62dB (red IEC-A)
Sintonizador de LW
Intervalo de frecuencias ... de 153 kHz a 281 kHz
Sensibilidad utilizable ...... 28µV (señal/ruido: 20 dB)
Relación de señal a ruido
................................... 62dB (red IEC-A)
Nota
Las especificaciones y el diseño están sujetos a
modificaciones sin previo aviso.
Información adicional
54
Apéndice
Es
Black plate (55,1)
Español
55Es
Black plate (56,1)
Vielen Dank, dass Sie sich für dieses
PIONEER-Produkt entschieden haben.
Bitte lesen Sie diese Anleitung vor der Verwen-
dung dieses Produkts zur Gewährleistung seiner
ordnungsgemäßen Verwendung durch. Lesen
und befolgen Sie dabei insbesondere die Hin-
weise WARNUNG und VORSICHT. Bewahren
Sie die Anleitung zur zukünftigen Bezugnahme si-
cher und griffbereit auf.
Mischen Sie dieses Produkt, wenn Sie es ent-
sorgen wollen, nicht mit gewöhnlichen Haus-
haltsabfällen. Es gibt ein getrenntes
Sammelsystem für gebrauchte elektronische
Produkte, über das die richtige Behandlung,
Rückgewinnung und Wiederverwertung
gemäß der bestehenden Gesetzgebung ge-
währleistet wird.
Privathaushalte in den Mitgliedstaaten der EU,
in der Schweiz und in Norwegen können ihre ge-
brauchten elektronischen Produkte kostenfrei
bei speziell dafür eingerichteten Sammelstellen
abgeben oder zu einem Fachhändler zurückbrin-
gen (sofern sie ein vergleichbares neues Produkt
kaufen).
In den Ländern, die hier nicht aufgeführt sind,
wenden Sie sich hinsichtlich der zu beachten-
den Entsorgungsweise bitte an die zuständige
Gemeindeverwaltung.
Auf diese Weise stellen Sie sicher, dass das zu
entsorgende Produkt der erforderlichen Verar-
beitung, Rückgewinnung und Wiederverwer-
tung zugeführt wird, und verhindern damit
potenziell negative Auswirkungen auf die Um-
welt sowie Gesundheitsschäden.
Zu diesem Gerät
Die Tuner-Frequenzen dieses Geräts sind für
Westeuropa, Asien, den Mittleren Osten, Afrika
und Ozeanien bestimmt. Der Gebrauch in ande-
ren Gebieten kann zu mangelhaftem Empfang
führen. Die RDS-Funktion (Radio-Datensystem)
ist nur in Gebieten mit UKW-Sendern verfügbar,
die RDS-Signale ausstrahlen.
Wichtig
Bitte tragen Sie die folgenden Informationen
in das dafür vorgesehene Formular auf der
Rückseite der Anleitung ein:
14-stellige Seriennummer (an der Unterseite
des Geräts angegeben)
Kaufdatum (Datum der Quittung)
Stempel des Händlers
Diese Informationen dienen als Eigentums-
nachweis. Im Fall eines Diebstahls teilen Sie
der Polizei die 14-stellige Seriennummer und
das Kaufdatum des Geräts mit.
Bewahren Sie die Bedienungsanleitung an
einem sicheren Ort auf.
VORSICHT
Bei diesem Gerät handelt es sich zwar um ein
Laserprodukt der Klasse 1, das entsprechend
dem Standard Sicherheit für Laserprodukte
IEC 60825-1:2007 klassifiziert ist.
LASER KLASSE 1
VORSICHT
! Dieses Gerät darf nicht mit Flüssigkeiten in
Kontakt kommen. Dies könnte einen Strom-
schlag verursachen. Darüber hinaus kann
der Kontakt mit Flüssigkeit eine Beschädi-
gung des Geräts, Rauchentwicklung und
Überhitzung nach sich ziehen.
! Wählen Sie stets eine Lautstärke, bei der Sie
Umgebungsgeräusche noch deutlich wahr-
nehmen können.
! Setzen Sie dieses Gerät keiner Feuchtigkeit
aus.
! Beim Abtrennen oder Entladen der Batterie
werden sämtliche vorprogrammierten Spei-
cher gelöscht.
Hinweis
Funktionseinstellungen werden selbst dann ab-
geschlossen, wenn das Menü vor dem Bestäti-
gen geschlossen wird.
Im Störungsfall
Sollte dieses Gerät nicht ordnungsgemäß funk-
tionieren, dann wenden Sie sich an Ihren Händ-
ler oder an die nächstgelegene PIONEER-
Kundendienststelle.
Bevor Sie beginnen
56
Abschnitt
Bevor Sie beginnen
De
01
Black plate (57,1)
Hauptgerät
b c
5
8
1 2 3 4 6
a9d7
Bezeichnung Bezeichnung
1 h (Auswurf) 8 BAND
2 SRC/OFF 9
(Zurück)/DIM-
MER (Dimmer)
3
MULTI-CONTROL
(M.C.)
a c/d
4
(Liste) b 1/ bis 6/
5 DISP c
AUX-Eingang
(3,5-mm-Stereo-
anschluss)
6 Disc-Ladeschacht d
Taste zum Entrie-
geln der Front-
platte
7
(Equalizer)
Display-Anzeige
21 3 75
9
4 6 8
a
Anzeige Status
1
(Liste)
Die Listenfunktion wird be-
dient.
2
Unterinfor-
mationsbe-
reich
Zum Anzeigen von Unterinfor-
mationen.
3
TA (Ver-
kehrsdurch-
sagen)
Die Verkehrsdurchsage ist ak-
tiviert.
4
TP (Ver-
kehrspro-
gramm-
Identifizie-
rung)
Es ist ein Sender, der Ver-
kehrsfunk anbietet, abge-
stimmt.
5
(Sound Ret-
riever)
Die Sound Retriever-Funk-
tion ist aktiviert.
6 LOC
Die Lokal-Suchlaufabstim-
mung ist aktiviert.
7
(Wieder-
holwieder-
gabe)
Die Titel- oder Ordner-Wieder-
holwiedergabe ist eingeschal-
tet.
8
(zufälli-
ge Wieder-
gabe)
Die zufallsgesteuerte Wieder-
gabe ist eingeschaltet.
9
Hauptinfor-
mationsbe-
reich
! Tuner: Frequenzband und
Frequenz
! RDS: Programm-Service-
Name, PTY-Information
und andere Textinforma-
tionen
! CD-Player: verstrichene
Wiedergabezeit und Texti-
nformationen
a
Erscheint, wenn eine unterge-
ordnete Ordner- oder Menü-
ebene vorhanden ist.
Setup-Menü
Wenn Sie nach der Installation den Zündschal-
ter in die Position EIN drehen, wird das Setup-
Menü auf dem Display angezeigt.
In diesem Menü können Sie folgende Optionen
einstellen.
1 Drehen Sie nach der Installation des Ge-
räts den Zündschalter auf EIN.
Die Angabe SET UP erscheint.
2 Drehen Sie M.C., um zu YES umzuschal-
ten.
# Bedienen Sie das Gerät nicht innerhalb von
30 Sekunden, wird das Setup-Menü nicht angezeigt.
# Wenn Sie diese Einstellung jetzt nicht vorneh-
men möchten, drehen Sie M.C., auf NO. Drücken
Sie den Regler, um die Auswahl zu bestätigen.
Wenn Sie NO wählen, können Sie keine Einstellun-
gen im Setup-Menü vornehmen.
3 Drücken Sie zur Auswahl M.C.
4 Gehen Sie zur Einstellung des Menüs fol-
gendermaßen vor.
Sie müssen Ihre Auswahl bestätigen, um die
nächste Menüoption aufrufen zu können.
LANGUAGE (Spracheinstellung)
Das Gerät kann Textinformationen komprimierter
Audiodateien auch dann anzeigen, wenn sie ent-
weder in einem lateinischen oder kyrillischen Al-
phabet aufgezeichnet wurden.
! Falls die für die Aufzeichnung verwendete
Sprache und die gewählte Spracheinstellung
nicht übereinstimmen, werden die Textinfor-
mationen ggf. nicht richtig angezeigt.
! Bestimmte Zeichen werden ggf. nicht ord-
nungsgemäß angezeigt.
1 Drehen Sie M.C., um die gewünschte Einstel-
lung zu wählen.
ENG (Englisch)РУС (Russisch)
2 Drücken Sie M.C., um die Auswahl zu bestäti-
gen.
CLOCK SET (Einstellen der Uhrzeit)
1 Drehen Sie M.C., um die Stunde einzustellen.
2 Drücken Sie auf M.C., um die Minuten auszu-
wählen.
3 Drehen Sie M.C., um die Minuten einzustellen.
4 Drücken Sie M.C., um die Auswahl zu bestäti-
gen.
FM STEP (UKW-Kanalraster)
Bei der Suchlaufabstimmung wird normalerweise
das 50-kHz-UKW-Kanalraster verwendet. Wenn
der Alternativfrequenzsuchlauf (AF) oder die Ver-
kehrsmeldungen (TA) eingeschaltet sind, ändert
sich das Kanalraster automatisch zu 100 kHz. Es
kann jedoch vorteilhaft sein, das Kanalraster für
den Alternativfrequenzsuchlauf auf 50 kHz einzu-
stellen.
! Bei der manuellen Abstimmung bleibt das Ka-
nalraster auf 50 kHz eingestellt.
1 Drehen Sie M.C., um die UKW-Kanalraster-
Funktion zu wählen.
50 (50 kHz)100 (100 kHz)
2 Drücken Sie M.C., um die Auswahl zu bestäti-
gen.
Die Angabe QUIT erscheint.
Deutsch
Bedienung des Geräts
57
Abschnitt
Bedienung des Geräts
De
02
Black plate (58,1)
5 Um die Einstellungen abzuschließen, dre-
hen Sie M.C., um zu YES zu wechseln.
# Wenn Sie die Einstellung erneut vornehmen
möchten, drehen Sie M.C.,umzuNO zu wechseln.
Drücken Sie den Regler, um die Auswahl zu bestäti-
gen.
6 Drücken Sie zur Auswahl M.C.
Hinweise
! Sie können die Menüoptionen über das Sys-
temmenü einstellen. Für Details zu den Ein-
stellungen siehe Systemmenü auf Seite 62.
! Das Einstellmenü kann durch Drücken von
SRC/OFF abgebrochen werden.
Grundlegende Bedienvorgänge
Wichtig
! Gehen Sie beim Abnehmen bzw. Anbringen
der Frontplatte sorgfältig vor.
! Setzen Sie die Frontplatte keinen übermäßi-
gen Stößen aus.
! Setzen Sie die Frontplatte weder direkter Son-
nenbestrahlung noch hohen Temperaturen
aus.
! Entfernen Sie alle etwaigen angeschlosse-
nen Kabel und Geräte, bevor Sie die Front-
platte abnehmen, um eine Beschädigung
des Geräts oder des Fahrzeuginneren zu ver-
meiden.
Entfernen der Frontplatte zum Schutz vor Dieb-
stahl
1 Drücken Sie die Taste zum Entriegeln der
Frontplatte.
2 Drücken Sie die Frontplatte nach oben (M) und
ziehen Sie sie in Ihre Richtung (N).
3 Bewahren Sie die abgenommene Frontplatte
stets in einer Schutzhülle, wie zum Beispiel
einem Etui, auf.
Wiederanbringen der Frontplatte
1 Schieben Sie die Frontplatte nach links.
Achten Sie darauf, die Zapfen links am Haupt-
gerät in die Aussparungen an der Frontplatte
einzuführen.
2 Drücken Sie dann gegen die rechte Seite der
Frontplatte, bis sie sicher einrastet.
Sollten Sie die Frontplatte nicht erfolgreich am
Hauptgerät anbringen können, stellen Sie si-
cher, dass sie korrekt vor dem Gerät positio-
niert ist. Wenden Sie keine Gewalt beim
Anbringen der Frontplatte an, da diese oder
das Hauptgerät sonst beschädigt werden
könnten.
Einschalten des Geräts
1 Drücken Sie die Taste SRC/OFF, um das Gerät
einzuschalten.
Ausschalten des Geräts
1 Drücken und halten Sie SRC/OFF gedrückt, bis
sich das Gerät ausschaltet.
Wählen einer Programmquelle
1 Drücken Sie SRC/OFF, um zwischen den fol-
genden Optionen umzuschalten:
TUNER (Tuner)CD (CD-Player)AUX (AUX)
Regeln der Lautstärke
1 Drehen Sie M.C., um die Lautstärke anzupas-
sen.
VORSICHT
Parken Sie Ihr Fahrzeug aus Sicherheitsgründen
zum Abnehmen der Frontplatte.
Hinweis
Wenn das blau/weiße Kabel dieses Geräts an
die Steuerklemme des Automatikantennenrelais
des Kraftfahrzeugs angeschlossen wird, wird die
Antenne ausgefahren, sobald das Gerät einge-
schaltet wird. Zum Einfahren der Antenne schal-
ten Sie die Programmquelle aus.
Häufig verwendete
Menüschritte
Zurückschalten zur vorherigen Anzeige
Zum Zurückschalten zur vorherigen Liste (bzw.
zum übergeordneten Ordner)
1 Drücken Sie
/DIMMER.
Zurückschalten zur normalen Anzeige
Beenden des Hauptmenüs
1 Drücken Sie BAND.
Zurückschalten zur normalen Anzeige von der
Liste
1 Drücken Sie BAND.
Tuner
Grundlegende Bedie nvorgänge
Wahl eines Bands (Wellenbereich)
1 Drücken Sie BAND, bis der gewünschte Wel-
lenbereich angezeigt wird (FM1, FM2, FM3 für
UKW bzw. MW/LW).
Wechseln der voreingestellten Sender
1 Drücken Sie c oder d.
! Wählen Sie PCH (voreingesteller Kanal) unter
SEEK, um diese Funktion verwenden zu kön-
nen. Für Details zu den Einstellungen siehe
SEEK (Einstellen der linken/rechten Tasten) auf
Seite 59.
Manuelle (schrittweise) Abstimmung
1 Drücken Sie c oder d.
! Wählen Sie MAN (manuelle Abstimmung)
unter SEEK, um diese Funktion verwenden zu
können. Für Details zu den Einstellungen
siehe SEEK (Einstellen der linken/rechten Tas-
ten) auf Seite 59.
Suchlauf
1 Drücken und halten Sie c oder d gedrückt
und lassen Sie die Taste dann wieder los.
Durch kurzes Drücken von c oder d kann die
Suchlaufabstimmung aufgehoben werden.
Durch Drücken und Gedrückthalten von c
oder d können Sender übersprungen werden.
Die Suchlaufabstimmung beginnt, sobald c
bzw. d losgelassen wird.
Hinweis
Der Alternativfrequenz-Suchlauf (AF) dieses Ge-
räts kann ein- und ausgeschaltet werden. Für
den normalen Abstimmbetrieb sollte AF ausge-
schaltet sein (siehe AF (Alternativfrequenz-Such-
lauf) auf Seite 59).
Bedienung des Geräts
58
Abschnitt
Bedienung des Geräts
De
02
Black plate (59,1)
Speichern und Abrufen von
Radiostationen für jedes Band
Verwendung der Stationstasten
1 Zum Speichern eines abgestimmten Sen-
ders drücken Sie eine der Stationstasten (1/
bis 6/ ) und halten diese gedrückt, bis
die Stationsnummer nicht mehr blinkt.
2 Drücken Sie eine der Stationstasten (1/
bis 6/ ) zur Auswahl der gewünschten Sta-
tion.
Umschalten der Anzeige
Wählen der gewünschten Textinformationen
1 Drücken Sie auf DISP, um zwischen den fol-
genden Optionen umzuschalten:
! FREQUENCY (Programm-Service-Name
oder Frequenz)
! BRDCST INFO (Programm-Service-Name/
PTY-Information)
! CLOCK (Programmquellname und Uhr)
Hinweise
! Wenn der Programm-Service-Name nicht
unter FREQUENCY abgerufen werden kann,
wird stattdessen die Sendefrequenz ange-
zeigt. Der Programm-Service-Name wird bei
einer Erkennung angezeigt.
! Die Textinformation BRDCST INFO ändert
sich automatisch.
! Je nach dem Band kann die Textinformation
geändert werden.
! Welche Textinformationen geändert werden
können, hängt vom Bereich ab.
Gebrauch der Programmtyp-
Funktionen (PTY)
Sie können einen Sender anhand eines Pro-
grammtyps (PTY) abstimmen.
Suchen nach RDS-Stationen anhand eines Pro-
grammtyps
Sie können nach Programmen eines allgemeinen
Typs suchen, wie die, die nachfolgend aufgelistet
sind. Siehe Seite 59.
1 Drücken Sie auf
(Liste).
2 Drehen Sie M.C., um einen Programmtyp zu
wählen.
NEWS/INFOPOPULARCLASSICS
OTHERS
3 Drücken Sie M.C., um die Suche zu starten.
Das Gerät sucht nach einer Station, die ein
Programm des gewählten Typs ausstrahlt.
Wenn eine solche Station gefunden wird, wird
deren Stationsname angezeigt.
! Zum Aufheben des Suchlaufs drücken Sie
M.C. erneut.
! Das Programm mancher Sender kann von
dem tatsächlich übertragenen Programm-
typ (PTY) abweichen.
! Wird kein Sender gefunden, der ein Pro-
gramm des gewählten Typs ausstrahlt,
dann erscheint zwei Sekunden lang NOT
FOUND und der Tuner schaltet auf die ur-
sprüngliche Station zurück.
PTY-Liste
NEWS/INFO (Nachrichten und Informationen)
NEWS (Nachrichten), AFFAIRS (Tagesereignisse),
INFO (Information), SPORT (Sport), WEATHER
(Wetter), FINANCE (Finanzen)
POPULAR (Pop)
POP MUS (Popmusik), ROCK MUS (Rockmusik),
EASY MUS (Leichte Hörmusik), OTH MUS (Ande-
re Musik), JAZZ (Jazz), COUNTRY (Countrymusik),
NAT MUS (Landesmusik), OLDIES (Oldies), FOLK
MUS (Volksmusik)
CLASSICS (Klassik)
L. CLASS (Leichte klassische Musik), CLASSIC
(Klassische Musik)
OTHERS (Sonstiges)
EDUCATE (Bildung), DRAMA (Drama), CULTURE
(Kultur), SCIENCE (Wissenschaft), VARIED (Ge-
mischtes), CHILDREN (Kinderprogramme), SO-
CIAL (Soziales), RELIGION (Religion), PHONE IN
(Telefongesprächsprogramme), TOURING (Rei-
sen), LEISURE (Freizeit), DOCUMENT (Dokumen-
tarsendungen)
Funktionseinstellungen
1 Drücken Sie auf M.C., um das Hauptmenü
anzuzeigen.
2 Drehen Sie M.C., um die Menüoption zu
wechseln, und drücken Sie auf FUNCTION,
um die angezeigte Option zu wählen.
3 Drehen Sie M.C., um die gewünschte
Funktion zu wählen.
Nach der Auswahl können die folgenden Funk-
tionen angepasst werden.
# Wenn das MW/LW-Band gewählt ist, stehen nur
BSM, LOCAL und SEEK zur Verfügung.
BSM (Best-Sender-Memory)
BSM (Best-Sender-Memory) speichert die sechs
stärksten Sender automatisch in der Reihenfolge
ihrer Signalstärke.
1 Drücken Sie M.C., um BSM einzuschalten.
Zum Abbrechen des Speichervorgangs drü-
cken Sie M.C. erneut.
REGION (Regional)
Bei Verwendung des Alternativfrequenz-Suchlaufs
beschränkt die Regionalfunktion die Auswahl auf
Sender, die regionale Programme ausstrahlen.
1 Drücken Sie M.C., um die Regionalfunktion
ein- oder auszuschalten.
LOCAL (Lokal-Suchlaufabstimmung)
Mit der Lokal-Suchlaufabstimmung wird nur nach
Stationen mit ausreichender Signalstärke für
einen guten Empfang gesucht.
1 Drücken Sie auf M.C., um die gewünschte Ein-
stellung zu wählen.
UKW: OFFLV1LV2LV3 LV4
MW/LW: OFFLV1 LV2
Bei Auswahl der höchsten Stufe werden nur
die stärksten Sender empfangen, während bei
Auswahl der niedrigeren Stufen schwächere
Sender zugelassen werden.
TA (Verkehrsdurchsagebereitschaft)
1 Drücken Sie M.C., um die Verkehrsdurchsage-
bereitschaft ein- oder auszuschalten.
AF (Alternativfrequenz-Suchlauf)
1 Drücken Sie M.C., um den Alternativfrequenz-
Suchlauf ein- oder auszuschalten.
NEWS (Nachrichtenunterbrechung)
1 Drücken Sie M.C., um die Nachrichtenfunk-
tion ein- oder auszuschalten.
SEEK (Einstellen der linken/rechten Tasten)
Sie können den linken und rechten Tasten des
Gerät eine Funktion zuweisen.
Wählen Sie MAN (manuelle Abstimmung) zur ma-
nuellen Abstimmung oder PCH (vorprogrammier-
ter Kanal) zum Umschalten zwischen den
vorprogrammierten Kanälen.
1 Drücken Sie M.C.,umMAN oder PCH zu wäh-
len.
Deutsch
Bedienung des Geräts
59
Abschnitt
Bedienung des Geräts
De
02
Black plate (60,1)
CD/CD-R/CD-RW-Discs
Grundlegende Bedie nvorgänge
Wiedergabe einer CD/CD-R/CD-RW-Disc
1 Legen Sie die Disc mit der Etikettenseite nach
oben in den Ladeschacht.
Auswerfen einer CD/CD-R/CD-RW-Disc
1 Drücken Sie auf h.
Wählen eines Ordners
1 Drücken Sie 1/
oder 2/ .
Wahl eines Titels
1 Drücken Sie c oder d.
Schnellvorlauf bzw. -rücklauf
1 Drücken und halten Sie c oder d gedrückt.
! Bei der Wiedergabe von Dateien im kompri-
mierten Audio-Format wird beim schnellen
Vor- und Rücklauf kein Ton ausgegeben.
Rückkehr zum Stammordner
1 Halten Sie BAND gedrückt.
Umschalten zwischen dem komprimierten Audio-
format und CD-DA
1 Drücken Sie BAND.
Umschalten der Anzeige
Wählen der gewünschten Textinformationen
1 Drücken Sie auf DISP, um zwischen den fol-
genden Optionen umzuschalten:
CD-DA
! ELAPSED TIME (Titelnummer und Wieder-
gabezeit)
! CLOCK (Programmquellname und Uhr)
! SPEANA (Spektralanalysator)
CD-TEXT
! TRACK INFO (Titelname/Titel-Künstler/
Disc-Titel)
! ELAPSED TIME (Titelnummer und Wieder-
gabezeit)
! CLOCK (Programmquellname und Uhr)
! SPEANA (Spektralanalysator)
MP3/WMA/WAV
! TRACK INFO (Titelname/Künstlername/Al-
bumtitel)
! FILE INFO (Dateiname/Ordnername)
! ELAPSED TIME (Titelnummer und Wieder-
gabezeit)
! CLOCK (Programmquellname und Uhr)
! SPEANA (Spektralanalysator)
Hinweise
! Die Textinformation TRACK INFO und
FILE INFO ändert sich automatisch.
! Abhängig vom Mediadateityp bzw. der für
das Schreiben der MP3-Dateien auf eine
Disc verwendeten Version von iTunes werden
die mit den Audiodateien gespeicherten Tex-
tinformationen ggf. nicht richtig angezeigt.
! Welche Textinformationen geändert werden
können, hängt vom Medium ab.
Auswählen und Wiedergeben von
Dateien/Titeln der Namensliste
1 Drücken Sie , um in den Datei-/Titellis-
tenmodus umzuschalten.
2 Verwenden Sie M.C., um den Namen der
gewünschten Datei (bzw. des gewünschten
Ordners) zu wählen.
Auswählen einer Datei oder eines Ordners
1 Drehen Sie M.C.
Wiedergabe
1 Drücken Sie nach Auswahl einer Datei oder
eines Titels auf M.C.
Anzeige einer Liste der Dateien (oder Ordner) im
gewählten Ordner
1 Drücken Sie nach Auswahl eines Ordners auf
M.C.
Wiedergabe eines Musiktitels im gewählten Ord-
ner
1 Drücken und halten Sie M.C. nach Auswahl
des Ordners gedrückt.
Bedienvorgänge mit speziellen
Tasten
Wählen eines Wiederholbereichs
1 Drücken Sie 6/
, um zwischen den folgen-
den Optionen umzuschalten:
! ALL Wiederholung aller Titel
! ONE Wiederholung des momentanen Ti-
tels
! FLD Wiederholung des momentanen
Ordners
Abspielen von Titeln in zufälliger Reihenfolge
1 Drücken Sie 5/
, um die zufallsgesteuerte
Wiedergabe ein- oder auszuschalten.
Die Titel innerhalb des gewählten Wiederhol-
bereichs werden in einer zufälligen Reihenfol-
ge gespielt.
! Um Titel während der zufälligen Wiedergabe
zu ändern, drücken Sie auf d, um zum nächs-
ten Titel zu wechseln. Durch Drücken von c
wird die Wiedergabe des aktuellen Titels von
seinem Anfang neu gestartet.
Pausieren der Wiedergabe
1 Drücken Sie 4/PAUSE, um die Wiedergabe an-
zuhalten oder fortzusetzen.
Verbessern der komprimierten Audiodaten und
Wiederherstellen eines reichen Klangbild (Sound
Retriever)
1 Drücken Sie 3/S.Rtrv, um zwischen den fol-
genden Optionen umzuschalten:
12OFF (Aus)
1 wirkt bei einem niedrigen und 2 bei einem
hohen Kompressionsfaktor.
Funktionseinstellungen
1 Drücken Sie auf M.C., um das Hauptmenü
anzuzeigen.
2 Drehen Sie M.C., um die Menüoption zu
wechseln, und drücken Sie auf FUNCTION,
um die angezeigte Option zu wählen.
Nach der Auswahl kann die unten stehende
Funktion angepasst werden.
S.RTRV (Sound Retriever)
Verbessert komprimierte Audiodaten und stellt ein
reiches Klangbild wieder her.
1 Drücken Sie auf M.C., um die gewünschte Ein-
stellung zu wählen.
Für detaillierte Informationen hierzu siehe Ver-
bessern der komprimierten Audiodaten und Wie-
derherstellen eines reichen Klangbild (Sound
Retriever) auf Seite 60.
Audio-Einstellungen
1 Drücken Sie auf M.C., um das Hauptmenü
anzuzeigen.
2 Drehen Sie M.C., um die Menüoption zu
wechseln, und drücken Sie auf AUDIO, um
die angezeigte Option zu wählen.
Bedienung des Geräts
60
Abschnitt
Bedienung des Geräts
De
02
Black plate (61,1)
3 Drehen Sie M.C., um die gewünschte
Audio-Funktion zu wählen.
Nach der Auswahl können die folgenden Audio-
funktionen angepasst werden.
! FADER steht nicht zur Verfügung, wenn in
SP-P/O MODE die Option SUB.W/SUB.W ge-
wählt wurde. Für detaillierte Informationen
hierzu siehe SP-P/O MODE (Heckausgang-
und Preout-Einstellungen) auf Seite 63.
! SUB.W, SUB.W CTRL und HPF SETTING ste-
hen nicht zur Verfügung, wenn in
SP-P/O MODE die Option REAR/REAR ge-
wählt wurde. Für detaillierte Informationen
hierzu siehe SP-P/O MODE (Heckausgang-
und Preout-Einstellungen) auf Seite 63.
! SUB.W CTRL und HPF SETTING stehen nicht
zur Verfügung, wenn in OFF die Option
SUB.W gewählt wurde. Für detaillierte Infor-
mationen hierzu siehe SUB.W (Subwoofer
Ein/Aus) auf Seite 61.
FADER (Überblendeinstellung)
1 Drücken Sie auf M.C., um den Einstellmodus
aufzurufen.
2 Drehen Sie M.C., um die Front-/Heck-Lautspre-
cherbalance einzustellen.
BALANCE (Balance-Einstellung)
1 Drücken Sie auf M.C., um den Einstellmodus
aufzurufen.
2 Drehen Sie M.C., um die Links-/Rechts-Laut-
sprecherbalance einzustellen.
EQ SETTING (Equalizer-Abruf)
1 Drücken Sie auf M.C., um den Einstellmodus
aufzurufen.
2 Drehen Sie M.C., um einen Equalizer zu wäh-
len.
POWERFULNATURALVOCALCUS-
TOM1CUSTOM2FLATSUPER BASS
Das Equalizer-Band und der Equalizer-Pegel
können individuell angepasst werden, wenn
CUSTOM1 oder CUSTOM2 gewählt ist.
Schließen Sie bei Wahl von CUSTOM1 oder
CUSTOM2 den unten genannten Vorgang ab.
Kehren Sie bei Wahl einer anderen Option
durch Drücken auf M.C. zur vorherigen Anzei-
ge zurück.
! CUSTOM1 kann für jede Quelle separat
eingestellt werden.
! Bei CUSTOM2 handelt es sich um eine ge-
meinsam verwendete Einstellung für alle
Quellen.
3 Drücken Sie auf M.C., um den Einstellmodus
aufzurufen.
4 Drücken Sie M.C., um zwischen den folgenden
Optionen umzuschalten:
EqualizerbandEqualizer-Pegel
5 Drehen Sie M.C., um die gewünschte Einstel-
lung zu wählen.
Equalizer-Band: 80HZ250HZ800HZ
2.5KHZ8KHZ
Equalizer-Pegel: +6 bis 6
! Sie können den Equalizer auch durch wieder-
holtes Drücken auf
wechseln.
LOUDNESS (Loudness)
Die Loudness-Funktion kompensiert die vermin-
derte Wahrnehmung von niedrigen und hohen
Frequenzen bei geringer Lautstärke.
1 Drücken Sie auf M.C., um die gewünschte Ein-
stellung zu wählen.
OFF (Aus)LOW (Niedrig)MID (Mittel)HI
(Hoch)
SUB.W (Subwoofer Ein/Aus)
Dieses Gerät ist mit einem Subwoofer-Ausgang
ausgestattet, der ein- und ausgeschaltet werden
kann.
1 Drücken Sie auf M.C., um die gewünschte Ein-
stellung zu wählen.
NOR (Normalphase)REV (Gegenphase)
OFF (Subwoofer Aus)
SUB.W CTRL (Subwoofer-Einstellungen)
Vom Subwoofer werden nur solche Frequenzen
ausgegeben, die unter dem gewählten Bereich lie-
gen.
1 Drücken Sie auf M.C., um den Einstellmodus
aufzurufen.
2 Drücken Sie M.C., um zwischen den folgenden
Optionen umzuschalten:
TrennfrequenzAusgabepegelPegel der
Steilheit
Einstellbare Werte blinken.
3 Drehen Sie M.C., um die gewünschte Einstel-
lung zu wählen.
Trennfrequenz: 50HZ63HZ80HZ100HZ
125HZ160HZ200HZ
Ausgangspegel: 24 bis +6
Pegel der Steilheit: 6 12
BASS BOOST (Bassverstärkung)
1 Drücken Sie auf M.C., um den Einstellmodus
aufzurufen.
2 Drehen Sie M.C., um den gewünschten Pegel
zu wählen.
Während der Erhöhung bzw. Verminderung
des Pegels wird 0 bis +6 angezeigt.
HPF SETTING (Hochpassfilter-Anpassung)
Wenn die im Ausgabe-Frequenzbereich des Sub-
woofers enthaltenen Basstöne nicht über den
Front- oder Hecklautsprecher ausgegeben werden
sollen, schalten Sie den Hochpassfilter (HPF) ein.
Über den Front- oder Heckausgang werden dann
nur Frequenzen ausgegeben, die über dem ge-
wählten Bereich liegen.
1 Drücken Sie auf M.C., um den Einstellmodus
aufzurufen.
2 Drücken Sie M.C., um zwischen den folgenden
Optionen umzuschalten:
TrennfrequenzPegel der Steilheit
3 Drehen Sie M.C., um die gewünschte Einstel-
lung zu wählen.
Trennfrequenz: OFF50HZ63HZ80HZ
100HZ125HZ160HZ200HZ
Pegel der Steilheit: 6 12
SLA (Programmquellen-Pegeleinstellung)
Mit der Programmquellen-Pegeleinstellung (SLA)
kann der Lautstärkepegel jeder Programmquelle
eingestellt werden, um plötzliche Lautstärkeände-
rungen beim Umschalten von Programmquellen
zu vermeiden.
! Die Einstellungen basieren auf der UKW-Laut-
stärke, die unverändert bleibt.
! Der MW/LW-Lautstärkepegel kann ebenfalls
mit dieser Funktion eingestellt werden.
! Bei der Wahl von UKW als Programmquelle
kann nicht auf SLA geschaltet werden.
1 Drücken Sie auf M.C., um den Einstellmodus
aufzurufen.
2 Drehen Sie M.C., um die Lautstärke für die
Programmquelle einzustellen.
Einstellbereich: +4 bis 4
Deutsch
Bedienung des Geräts
61
Abschnitt
Bedienung des Geräts
De
02
Black plate (62,1)
Systemmenü
Wichtig
Die Funktion PW SAVE (Energiesparmodus)
wird deaktiviert, wenn die Fahrzeugbatterie ab-
geklemmt wird und muss neu aktiviert werden,
sobald die Batterie wieder angeschlossen wird.
Wenn PW SAVE (Energiesparmodus) deaktiviert
ist, kann das Gerät je nach Anschlussart Batte-
rieleistung in Anspruch nehmen, sollte die Zün-
dung des Fahrzeugs über keine ACC-Position
(Zubehörposition) verfügen.
1 Drücken Sie auf M.C., um das Hauptmenü
anzuzeigen.
2 Drehen Sie M.C., um die Menüoption zu
wechseln, und drücken Sie auf SYSTEM, um
die angezeigte Option zu wählen.
3 Drehen Sie M.C., um die Systemmenü-
Funktion zu wählen.
Nach der Auswahl können die folgenden Sys-
temmenüfunktionen angepasst werden.
LANGUAGE (Spracheinstellung)
Das Gerät kann Textinformationen komprimierter
Audiodateien auch dann anzeigen, wenn sie ent-
weder in einem lateinischen oder kyrillischen Al-
phabet aufgezeichnet wurden.
! Falls die für die Aufzeichnung verwendete
Sprache und die gewählte Spracheinstellung
nicht übereinstimmen, werden die Textinfor-
mationen ggf. nicht richtig angezeigt.
! Bestimmte Zeichen werden ggf. nicht ord-
nungsgemäß angezeigt.
1 Drehen Sie M.C., um die gewünschte Einstel-
lung zu wählen.
ENG (Englisch)РУС (Russisch)
CLOCK SET (Einstellen der Uhrzeit)
1 Drücken Sie auf M.C., um den Einstellmodus
aufzurufen.
2 Drücken Sie M.C., um den Teil der Zeitanzeige
zu wählen, der eingestellt werden soll.
StundenMinuten
3 Drehen Sie M.C., um die Uhrzeit einzustellen.
12H/24H (Uhrzeitformat)
1 Drücken Sie auf M.C., um die gewünschte Ein-
stellung zu wählen.
12H (12-Stunden-Uhr)24H (24-Stunden-Uhr)
AUTO PI (Automatische PI-Suche)
Das Gerät kann selbst bei einem Stationsabruf au-
tomatisch nach einer anderen Station mit dersel-
ben Programmierung suchen.
1 Drücken Sie M.C., um den Auto-PI-Suchlauf
ein- oder auszuschalten.
AUX (Zusatzeingang)
Aktivieren Sie diese Einstellung, wenn ein zusätzli-
ches, mit diesem Gerät verbundenes Gerät ver-
wendet wird.
1 Drücken Sie M.C.,umAUX ein- oder auszu-
schalten.
MUTE MODE (Stummschaltung)
Die Klangwiedergabe dieses Geräts wird automa-
tisch stummgeschaltet oder gedämpft, wenn das
Signal eines Geräts mit Stummschaltung empfan-
gen wird.
1 Drücken Sie auf M.C., um den Einstellmodus
aufzurufen.
2 Drehen Sie M.C., um die gewünschte Einstel-
lung zu wählen.
Sie können eine beliebige Option aus der fol-
genden Liste wählen:
! MUTE Stummschaltung
! 20dB ATT Dämpfung (20dB ATT hat eine
stärkere Wirkung als 10dB ATT)
! 10dB ATT Dämpfung
PW SAVE (Energiesparmodus)
Wenn Sie diese Funktion einschalten, reduzieren
Sie den Verbrauch von Batterieleistung.
! Bei aktiviertem Energiesparmodus kann nur
die Programmquelle eingeschaltet werden.
1 Drücken Sie M.C., um den Energiesparmodus
ein- oder auszuschalten.
Umschalten der Dimmer-
Einstellung
Sie können die Helligkeit der Beleuchtung ein-
stellen.
1 Drücken Sie auf M.C., um das Hauptmenü
anzuzeigen.
2 Drehen Sie M.C., um die Option ILLUMI
zur Anzeige zu bringen, und drücken Sie
dann darauf, um Ihre Auswahl zu bestäti-
gen.
3 Drücken Sie auf M.C., um die gewünschte
Einstellung zu wählen.
OFF (Aus)ON (Ein)
! Sie können die Dimmer-Einstellung auch
durch Drücken und Halten von
/DIMMER
ändern.
Grundmenü
1 Drücken und halten Sie SRC/OFF ge-
drückt, bis sich das Gerät ausschaltet.
2 Drücken und halten Sie SRC/OFF ge-
drückt, bis das Hauptmenü im Display er-
scheint.
3 Drehen Sie M.C., um die Menüoption zu
wechseln, und drücken Sie auf INITIAL, um
die angezeigte Option zu wählen.
4 Drehen Sie M.C., um die Grundmenü-
Funktion zu wählen.
Nach der Auswahl können die folgenden Grund-
menüfunktionen angepasst werden.
FM STEP (UKW-Kanalraster)
Bei der Suchlaufabstimmung wird normalerweise
das 50-kHz-UKW-Kanalraster verwendet. Wenn
der Alternativfrequenzsuchlauf (AF) oder die Ver-
kehrsmeldungen (TA) eingeschaltet sind, ändert
sich das Kanalraster automatisch zu 100 kHz. Es
kann jedoch vorteilhaft sein, das Kanalraster für
den Alternativfrequenzsuchlauf auf 50 kHz einzu-
stellen.
! Bei der manuellen Abstimmung bleibt das Ka-
nalraster auf 50 kHz eingestellt.
1 Drücken Sie M.C., um die UKW-Kanalraster-
Funktion zu wählen.
50 (50 kHz)100 (100 kHz)
Bedienung des Geräts
62
Abschnitt
Bedienung des Geräts
De
02
Black plate (63,1)
SP-P/O MODE (Heckausgang- und Preout-Einstel-
lungen)
Der Hecklautsprecher-Leitungsausgang und
Cinch-Ausgang dieses Geräts können zum An-
schluss eines Vollbereichslautsprechers oder Sub-
woofers verwendet werden. Wählen Sie für Ihren
Anschluss eine geeignete Option.
1 Drücken Sie auf M.C., um den Einstellmodus
aufzurufen.
2 Drehen Sie M.C., um die gewünschte Einstel-
lung zu wählen.
Sie können eine beliebige Option aus der fol-
genden Liste wählen:
! REAR/SUB.W Wählen Sie diese Option,
wenn ein Vollbereichslautsprecher an den
Hecklautsprecher-Leitungsausgang und
ein Subwoofer an den Cinch-Ausgang an-
geschlossen ist.
! SUB.W/SUB.W Wählen Sie diese Option,
wenn ein Subwoofer an den Hecklautspre-
cher-Leitungsausgang ohne Verwendung
eines zusätzlichen Verstärkers und ein Sub-
woofer an den Cinch-Ausgang angeschlos-
sen ist.
! REAR/REAR Wählen Sie diese Option,
wenn ein Vollbereichslautsprecher an den
Hecklautsprecher-Leitungsausgang und
den Cinch-Ausgang angeschlossen ist.
Wenn ein Vollbereichslautsprecher an den
Hecklautsprecher-Leitungsausgang ange-
schlossen ist und der Cinch-Ausgang nicht
verwendet wird, können Sie entweder
REAR/SUB.W oder REAR/REAR auswäh-
len.
Systemmenü
1 Drücken und halten Sie SRC/OFF ge-
drückt, bis sich das Gerät ausschaltet.
2 Drücken und halten Sie SRC/OFF ge-
drückt, bis das Hauptmenü im Display er-
scheint.
3 Drehen Sie M.C., um die Menüoption zu
wechseln, und drücken Sie auf SYSTEM, um
die angezeigte Option zu wählen.
4 Drehen Sie M.C., um die Systemmenü-
Funktion zu wählen.
Nach der Auswahl können die folgenden Sys-
temmenüfunktionen angepasst werden.
Für detaillierte Informationen hierzu siehe Sys-
temmenü auf Seite 62.
Verwendung der AUX-
Programmquelle
1 Verbinden Sie den Stereo-Mini-Klinken-
stecker mit dem AUX-Eingang.
2 Drücken Sie die Taste SRC/OFF, um AUX
als Programmquelle zu wählen.
Hinweis
AUX kann nur gewählt werden, wenn die AUX-
Einstellung eingeschaltet wurde. Für weitere
Einzelheiten siehe AUX (Zusatzeingang) auf
Seite 62.
Umschalten der Anzeige
Wählen der gewünschten Textinformationen
1 Drücken Sie auf DISP, um zwischen den fol-
genden Optionen umzuschalten:
! Programmquellenname
! Programmquellname und Uhr
Bei Anzeige einer
unerwünschten Anzeige
Schalten Sie die unerwünschte Anzeige anhand
des unten beschriebenen Vorgangs aus.
1 Drücken Sie auf M.C., um das Hauptmenü
anzuzeigen.
2 Drehen Sie M.C., um die Menüoption zu
wechseln, und drücken Sie auf SYSTEM, um
die angezeigte Option zu wählen.
3 Drehen Sie M.C., um die Option
DEMO OFF zur Anzeige zu bringen, und drü-
cken Sie dann darauf, um Ihre Auswahl zu
bestätigen.
4 Drehen Sie M.C., um zu YES umzuschal-
ten.
5 Drücken Sie zur Auswahl M.C.
Deutsch
Bedienung des Geräts
63
Abschnitt
Bedienung des Geräts
De
02
Black plate (64,1)
Anschlüsse
Wichtig
! Bei der Installation des Geräts in einem
Kraftfahrzeug, das am Zündschalter keine
Position ACC aufweist, kann es je nach An-
schlusstyp zu einer Entleerung der Fahrzeug-
batterie kommen, wenn das rote Kabel nicht
mit dem Anschluss verbunden wurde, der
für die Erkennung des Zündschlüsselbet-
riebs verantwortlich ist.
O
N
S
T
A
R
T
O
F
F
Zündung mit Position
ACC
Zündung ohne Posi-
tion ACC
! Der Einsatz dieses Geräts in einer anderen
als der nachstehend angegebenen Betriebs-
umgebung kann einen Brand auslösen oder
eine Funktionsstörung zur Folge haben:
Kraftfahrzeuge mit 12-Volt-Batterie und nega-
tiver Erdung.
Lautsprecher mit 50 W (Ausgabe) und 4 W bis
8 W (Impedanz).
! Um Kurzschluss, Überhitzung oder Funk-
tionsstörungen zu vermeiden, halten Sie sich
stets an die nachstehend aufgeführten An-
weisungen:
Trennen Sie die Verbindung zur negativen An-
schlussklemme der Fahrzeugbatterie, bevor
Sie das Gerät installieren.
Sichern Sie die Kabel mit Kabelklemmen
oder Klebeband. Zum Schutz der Verkabe-
lung sollten die Kabel an allen Stellen, an
denen sie mit Metallteilen in Berührung kom-
men, mit Isolierband umwickelt werden.
Bringen Sie die Kabel in sicherer Entfernung
von beweglichen Fahrzeugkomponenten, wie
z. B. Schalthebel und Sitzschienen, an.
Bringen Sie die Kabel in größtmöglicher Ent-
fernung von Stellen an, die sich erhitzen, wie
z. B. die Heizungsöffnung.
Führen Sie das gelbe Batteriekabel nicht
durch ein Loch in den Motorraum, um die
Verbindung mit der Fahrzeugbatterie herzu-
stellen.
Kleben Sie freie Kabelanschlüsse mit Isolier-
band ab.
Kürzen Sie die Kabel nicht.
Entfernen Sie niemals die Isolierung des
Stromkabels dieses Geräts, um die Stromzu-
fuhr mit einem anderen Gerät zu teilen. Da-
durch wird die Stromversorgungsleistung des
Kabels beeinträchtigt.
Verwenden Sie eine Sicherung, die den vorge-
gebenen Leistungsmerkmalen entspricht.
Verdrahten Sie das negative Lautsprecherka-
bel niemals direkt mit der Erde.
Gruppieren Sie niemals die negativen Kabel
mehrerer Lautsprecher.
! Wenn dieses Gerät eingeschaltet wird, liegen
Steuersignale am blau/weißen Kabel an. Ver-
binden Sie dieses Kabel mit der Systemfern-
bedienung eines externen
Leistungsverstärkers oder der Steuerklemme
des Automatikantennenrelais des Kraftfahr-
zeugs (max. 300 mA, 12 V Gleichspannung).
Wenn das Fahrzeug mit einer in die Heck-
scheibe integrierten Radioantenne ausge-
stattet ist, verbinden Sie das Kabel mit der
Versorgungsklemme des Antennenboosters.
! Verbinden Sie das blau/weiße Kabel niemals
mit der Leistungsklemme des externen Leis-
tungsverstärkers. Darüber hinaus darf das
Kabel keinesfalls mit der Leistungsklemme
der Fahrzeugantenne verbunden werden. An-
dernfalls kann es zu einer Entleerung oder
Funktionsstörung der Fahrzeugbatterie kom-
men.
! Das schwarze Kabel gewährleistet die Er-
dung. Dieses Kabel wie auch die Erdungska-
bel anderer Produkte (insbesondere von
Hochstromprodukten wie Leistungsverstär-
ker) müssen separat verdrahtet werden. An-
derenfalls kann es zu einem Brand oder
einer Funktionsstörung kommen, wenn sich
die Kabel versehentlich lösen.
Dieses Gerät
3 45
21
1 Netzkabelzugang
2 Heck- oder Subwooferausgang
3 Antenneneingang
4 Sicherung (10 A)
5 Eingang der festverdrahteten Fernbedienung
Es besteht die Möglichkeit, einen (separat er-
hältlichen) festverdrahteten Fernbedienungs-
adapter anzuschließen.
Netzkabel
1
3
3
2
4
4
5
5
6
6
b
8
9
7
a
e
d
c
1 Zum Netzzugang
2 Je nach Fahrzeugtyp können die Funktionen
3 und 5 variieren. Stellen Sie in diesem Fall
sicher, dass der Anschluss von 4 nach 5
und 6 nach 3 erfolgt.
3 Gelb
Reserveversorgung (oder Zubehör)
4 Gelb
Verbindung mit der Klemme der konstanten
12-V-Spannungsversorgung.
5 Rot
Zubehör (oder Reserveversorgung)
6 Rot
Verbindung mit der Klemme der zündungs-
gesteuerten Spannungsversorgung (12 V
Gleichspannung).
7 Verbinden Sie jeweils Anschlüsse derselben
Farbe miteinander.
8 Schwarz (Fahrgestell-Erdung)
Installation
64
Abschnitt
Installation
De
03
Black plate (65,1)
9 Blau/Weiß
Die Pin-Position des ISO-Anschlusses variiert
je nach Fahrzeugtyp. Wird Pin 5 zur Steue-
rung der Antenne verwendet, verbinden Sie
9 und b. Verbinden Sie in jedem anderen
Fahrzeugtyp niemals 9 und b.
a Blau/Weiß
Verbindung mit der Systemsteuerungsklem-
me des Leistungsverstärkers (max. 300 mA,
12 V Gleichspannung).
b Blau/Weiß
Verbindung mit der Steuerungsklemme des
Automatikantennenrelais (max. 300 mA 12 V
Gleichspannung).
c Gelb/Schwarz
Wenn Sie ein Gerät mit Stummschaltfunk-
tion verwenden, verbinden Sie diesen Draht
mit dem Draht der Audio-Stummschaltung
dieses Geräts. Andernfalls sollte der Draht
der Audio-Stummschaltung (Mute) frei blei-
ben.
d Lautsprecherkabel
Weiß: Vorn links +
Weiß/Schwarz: Vorn links *
Grau: Vorn rechts +
Grau/Schwarz: Vorn rechts *
Grün: Hinten links + oder Subwoofer +
Grün/Schwarz: Hinten links * oder Subwo-
ofer *
Violett: Hinten rechts + oder Subwoofer +
Violett/Schwarz: Hinten rechts * oder Sub-
woofer *
e ISO-Anschluss
Bei manchen Fahrzeugtypen kann der ISO-
Anschluss zweigeteilt sein. Stellen Sie in die-
sem Fall sicher, dass zu beiden Anschlüssen
Verbindungen hergestellt werden.
Hinweise
! Ändern Sie das Grundeinstellmenü dieses
Geräts. Siehe SP-P/O MODE (Heckausgang-
und Preout-Einstellungen) auf Seite 63.
Die Subwoofer-Ausgabe dieses Geräts erfolgt
in Mono.
! Bei Verwendung eines 70-W-Subwoofers
(2 W) muss sichergestellt werden, dass der
Subwoofer am violetten und violett/schwar-
zen-Anschluss dieses Geräts angeschlossen
wird. Schließen Sie nichts an den grünen
und grün/schwarzen-Anschluss an.
Leistungsverstärker (separat
erhältlich)
Führen Sie diese Verkabelungen beim Gebrauch
eines optionalen Verstärkers durch.
1
3
2
4
55
1 Systemfernbedienung
Verbindung mit blau/weißem Kabel.
2 Leistungsverstärker (separat erhältlich)
3 Verbindung mit Cinch-Kabeln (separat er-
hältlich)
4 Zum Heck- oder Subwooferausgang
5 Hecklautsprecher oder Subwoofer
Installation
Wichtig
! Überprüfen Sie vor der endgültigen Installa-
tion alle Anschlüsse und Systeme.
! Die Verwendung nicht zugelassener Teile
kann eine Funktionsstörung zur Folge haben.
! Wenden Sie sich an Ihren Fachhändler, wenn
für die Installation Löcher gebohrt oder ande-
re Änderungen am Fahrzeug vorgenommen
werden müssen.
! Installieren Sie dieses Gerät keinesfalls an
folgenden Orten:
Orte, an denen das Gerät die Steuerung des
Fahrzeugs behindern könnte.
Orte, an denen das Gerät die Insassen des
Fahrzeugs im Anschluss an eine Schnell-
bremsung verletzen könnte.
! Der Halbleiterlaser kann durch Überhitzung
beschädigt werden. Installieren Sie dieses
Gerät deshalb in sicherer Entfernung von Hit-
zequellen, wie z. B. Heizöffnungen.
! Optimale Leistung kann durch eine Installa-
tion des Geräts in einem Winkel unter 60° er-
zielt werden.
60°
! Um beim Gebrauch des Geräts eine ord-
nungsgemäße Wärmezerstreuung zu ge-
währleisten, ist bei der Installation genügend
Freiraum hinter der Rückseite vorzusehen.
Lose Kabel sind aufzuwickeln, damit sie die
Lüftung nicht behindern.
Reichlich Platz lassen
5 cm
5 cm
Front-/Rückmontage nach DIN
Dieses Gerät kann sowohl über die Front- als
auch über die Rückmontage installiert werden.
Verwenden Sie für die Montage im Handel er-
hältliches Zubehör.
DIN-Frontmontage
1 Führen Sie den Montagerahmen in das
Armaturenbrett ein.
Verwenden Sie den mitgelieferten Montagerah-
men, wenn bei der Installation wenig Platz zur
Verfügung steht. Bei ausreichendem Platz kann
der mit dem Fahrzeug mitgelieferte Montagerah-
men verwendet werden.
2 Befestigen Sie den Montagerahmen mit-
hilfe eines Schraubendrehers: Die Metall-
klammern sind in eine sichere Position (90°)
zu biegen.
1
2
1 Armaturenbrett
2 Montagerahmen
# Stellen Sie sicher, dass das Gerät fest angebracht
ist. Ein instabiler Einbau kann zum Aussetzen von
Tönen führen oder andere Fehlfunktionen verursa-
chen.
DIN-Rückmontage
1 Bestimmen Sie die geeignete Position,
damit die Löcher an der Klammer und den
Geräteseiten ordnungsgemäß ausgerichtet
sind.
Deutsch
Installation
65
Abschnitt
Installation
De
03
Black plate (66,1)
2 Ziehen Sie auf jeder Seite zwei Schrau-
ben fest.
1
2
3
1 Blechschraube (5 × 8 mm)
2 Montageklammer
3 Armaturenbrett oder Konsole
Entfernen des Geräts
1 Entfernen Sie den Einpassungsring.
1 Einpassungsring
2 Aussparung
! Bei entriegelter Bedienfläche lässt sich der
Einpassungsring einfacher erreichen.
! Halten Sie beim Wiederanbringen des Ein-
passungsrings die Seite mit der Aussparung
nach unten.
2 Führen Sie die mitgelieferten Extrak-
tionsschlüssel an beiden Geräteseiten ein,
bis sie in der richtigen Position einrasten.
3 Ziehen Sie das Gerät aus dem Armaturen-
brett.
Abnehmen und Wiederanbringen der
Frontplatte
Sie können die Frontplatte zum Schutz vor Dieb-
stahl abnehmen.
Drücken Sie die Taste zum Entriegeln der Front-
platte und schieben Sie sie nach oben und auf
Sie zu.
Detaillierte Informationen hierzu finden Sie
unter Entfernen der Frontplatte zum Schutz vor
Diebstahl und Wiederanbringen der Frontplatte
auf Seite 58.
Fehlerbehebung
Symptom Ursache Abhilfemaßnah-
me
Das Display
schaltet auto-
matisch in die
normale An-
zeige um.
Sie haben kei-
nen Bedienvor-
gang innerhalb
von 30 Sekun-
den durchge-
führt.
Wiederholen Sie
den Vorgang.
Der Wieder-
holbereich
ändert sich
unerwartet.
Ja nach Wieder-
holbereich kann
sich der ausge-
wählte Bereich
ändern, sobald
ein anderer Ord-
ner oder Musik-
titel ausgewählt
wird oder wäh-
rend des
schnellen Vor-
und Rücklaufs.
Wählen Sie den
Wiederholbereich
erneut aus.
Ein Unterord-
ner wird nicht
wiedergege-
ben.
Unterordner
können nicht
wiedergegeben
werden, wenn
FLD (Ordner-
Wiederholung)
ausgewählt ist.
Wählen Sie einen
anderen Wieder-
holbereich.
NO XXXX er-
scheint, wenn
sich die An-
zeige ändert
(z. B. NO
TITLE).
Es sind keine
Textinformatio-
nen eingebettet.
Schalten Sie die
Anzeige um oder
spielen Sie einen
anderen Titel bzw.
eine andere Datei
ab.
Symptom Ursache Abhilfemaßnah-
me
Im Gerät ist
eine Fehlfunk-
tion aufgetre-
ten.
Es liegen
Funkstörun-
gen vor.
Sie verwenden
in der Nähe die-
ser Einheit ein
Gerät, wie z. B.
ein Mobiltele-
fon, welches
elektromagneti-
sche Frequen-
zen aussendet.
Lassen Sie einen
ausreichenden
Abstand zwi-
schen dieser Ein-
heit und den
Geräten, die die
Funkstörung ver-
ursachen.
Fehlermeldungen
Vor der Kontaktaufnahme mit Ihrem Händler
oder der nächstgelegenen Pioneer-Kunden-
dienststelle sollten Sie sich die angezeigte Feh-
lermeldung notieren.
Allgemeines
Meldung Ursache Abhilfemaßnah-
me
AMP ERROR Betriebsstörung
des Geräts oder
falsche Laut-
sprecherverbin-
dung; Schutz-
schaltung ist
aktiviert.
Überprüfen Sie
die Lautsprecher-
verbindung.
Wenn die Mel-
dung selbst nach
dem Aus-/Ein-
schalten des Mo-
tors weiterhin
angezeigt wird,
wenden Sie sich
zur Unterstützung
an Ihren Händler
oder eine Pioneer-
Kundendienststel-
le.
Installation
66
Abschnitt
Zusätzliche Informationen
De
03
Black plate (67,1)
CD-Player
Meldung Ursache Abhilfemaßnah-
me
ERROR-07,
11, 12, 17, 30
Die Disc ist ver-
schmutzt.
Reinigen Sie die
Disc.
Die Disc ist ver-
kratzt.
Wechseln Sie die
Disc aus.
ERROR-07,
10, 11, 12,
15, 17, 30,
A0
Es liegt ein
elektrischer
oder mechani-
scher Fehler vor.
Schalten Sie die
Zündung aus
(OFF) und wieder
ein (ON) oder
schalten Sie auf
eine andere Pro-
grammquelle um
und dann wieder
zum CD-Player
zurück.
ERROR-15 Die eingelegte
Disc ist leer.
Wechseln Sie die
Disc aus.
ERROR-23 Nicht unter-
stütztes CD-For-
mat.
Wechseln Sie die
Disc aus.
FORMAT
READ
Nach dem Wie-
dergabestart ist
der Ton in man-
chen Fällen erst
nach einer Ver-
zögerung zu
hören.
Warten Sie bis die
Anzeige erlischt
und Sie einen Ton
hören.
NO AUDIO Die eingelegte
Disc enthält
keine abspielba-
ren Dateien.
Wechseln Sie die
Disc aus.
SKIPPED Die eingelegte
Disc enthält Da-
teien mit DRM-
Schutz (digitale
Rechteverwal-
tung).
Wechseln Sie die
Disc aus.
Meldung Ursache Abhilfemaßnah-
me
PROTECT Alle Dateien auf
der eingelegten
Disc weisen
einen DRM-
Schutz (digitale
Rechteverwal-
tung) auf.
Wechseln Sie die
Disc aus.
Handhabungsrichtlinien
Discs und Player
Verwenden Sie ausschließlich Discs, die eines der
folgenden zwei Logos aufweisen:
Verwenden Sie 12-cm-Discs. 8-cm-Discs bzw.
Adapter für 8-cm-Discs dürfen nicht verwendet
werden.
Verwenden Sie ausschließlich herkömmliche,
runde Discs. Discs einer anderen Form sollten
nicht verwendet werden.
In den CD-Ladeschacht darf kein anderer Gegen-
stand als eine CD eingeführt werden.
Verwenden Sie keinesfalls Discs, die Sprünge, Ein-
kerbungen/Absplitterungen, Verformungen oder
andere Beschädigungen aufweisen, da Sie da-
durch den Player beschädigen könnten.
CD-R/RW-Discs, deren Aufzeichnungen nicht ab-
geschlossen (finalisiert) wurden, können nicht ab-
gespielt werden.
Berühren Sie unter keinen Umständen die Disc-
Oberfläche mit den aufgezeichneten Daten.
Bewahren Sie die Discs bei Nichtgebrauch in
deren Hülle auf.
Kleben Sie keine Etiketten auf Discs, beschriften
Sie sie nicht und wenden Sie keine Chemikalien
auf die Disc-Oberfläche an.
Wischen Sie die Discs zum Reinigen mit einem
weichen Tuch von der Mitte zum Rand hin ab.
Kondensation kann eine vorübergehende Störung
der Player-Leistung zur Folge haben. Warten Sie in
diesem Fall etwa eine Stunde ab, bis sich der
Player an die höheren Temperaturen angepasst
hat. Zudem sollten feuchte Discs mit einem wei-
chen Tuch trockengerieben werden.
Unter Umständen ist eine Disc-Wiedergabe nicht
möglich. Das kann auf die spezifischen Eigen-
schaften der Disc, das Disc-Format, die für die
Aufzeichnung verwendete Software, die Wiederga-
beumgebung, die Lagerbedingungen usw. zurück-
zuführen sein.
Erschütterungen aufgrund von Unebenheiten der
Fahrbahn können die Disc-Wiedergabe unterbre-
chen.
Lesen Sie sich vor der Verwendung von Discs die
Disc-spezifischen Sicherheitshinweise durch.
Bei Verwendung von bedruckbaren Discs, beach-
ten Sie die Anleitung und die Warnhinweise der
Disc. Je nach Beschaffenheit der Discs, können
Sie eventuell nicht eingelegt oder ausgeworfen
werden. Die Verwendung solcher Discs kann zu
einer Beschädigung dieses Gerätes führen.
Bringen Sie keine handelsüblichen Etiketten oder
andere Materialien auf den Discs an.
! Die Discs können sich verformen und werden
nicht wiedergegeben.
! Die Etiketten können sich während der Wieder-
gabe lösen und den Auswurf behindern, wo-
durch das Gerät beschädigt werden könnte.
DualDiscs
DualDiscs sind doppelseitige Discs, die eine be-
schreibbare CD-Seite für Audio- und eine be-
schreibbare DVD-Seite für Video-Daten
bereitstellen.
Da die CD-Seite von DualDiscs physikalisch nicht
mit dem allgemeinen CD-Standard kompatibel ist,
ist eine Wiedergabe der CD-Seite mit diesem
Gerät ggf. nicht möglich.
Das häufige Einlegen und Auswerfen einer
DualDisc kann zu Kratzern auf der Disc führen,
die wiederum, wenn sie besonders ausgeprägt
sind, Probleme bei der Wiedergabe auf diesem
Gerät zur Folge haben können. In manchen Fällen
kann es sogar vorkommen, dass eine DualDisc im
Disc-Ladeschacht eingeklemmt wird und nicht
mehr ausgeworfen werden kann. Um dies zu ver-
meiden, wird empfohlen, von der Verwendung von
DualDiscs mit diesem Gerät abzusehen.
Detaillierte Angaben zu DualDiscs können Sie den
vom Hersteller der Disc bereitgestellten Informa-
tionen entnehmen.
Deutsch
Zusätzliche Informationen
67
Anhang
Zusätzliche Informationen
De
Black plate (68,1)
Kompatibilität mit Audio-
Kompression
WMA
Dateierweiterung: .wma
Bitrate: 48 Kbit/s bis 320 Kbit/s (CBR - Konstante
Bitrate), 48 Kbit/s bis 384 Kbit/s (VBR - Variable Bit-
rate)
Abtastfrequenz: 32 kHz; 44,1 kHz; 48 kHz
Windows Media Audio Professional, Lossless,
Voice/DRM Stream/Stream mit Video: Nicht kom-
patibel
MP3
Dateierweiterung: .mp3
Bitrate: 8 Kbit/s bis 320 Kbit/s (CBR), VBR
Abtastfrequenz: 8 kHz bis 48 kHz (32 kHz; 44,1 kHz;
48 kHz für Emphase)
Kompatible ID3-Tag-Version: 1.0, 1.1, 2.2, 2.3, 2.4
(ID3-Tag-Version 2.x erhält Vorrang vor Version 1.x)
M3u-Spielliste: Nicht kompatibel
MP3i (MP3 interaktiv), mp3 PRO: Nicht kompati-
bel
WAV
Dateierweiterung: .wav
Quantisierungsbits: 8 und 16 (LPCM), 4 (MS
ADPCM)
Abtastfrequenz: 16 kHz bis 48 kHz (LPCM);
22,05 kHz und 44,1 kHz (MS ADPCM)
Zusätzliche Informationen
Von Dateinamen (einschließlich der Dateierweite-
rung) bzw. von Ordnernamen können jeweils nur
die ersten 32 Zeichen angezeigt werden.
Damit kyrillische Buchstaben auf diesem Gerät
angezeigt werden können, müssen diese mit
einem der folgenden Zeichensätze codiert worden
sein:
! Unicode (UTF-8, UTF-16)
! Andere Zeichensätze als Unicode, die in einer
Windows-Umgebung verwendet und in den
Sprachoptionen auf Russisch eingestellt wur-
den.
Je nach der Anwendung, die für die Codierung
der WMA-Dateien verwendet wurde, funktioniert
dieses Gerät ggf. nicht ordnungsgemäß.
Disc
Abspielbare Ordnerstruktur: bis zu acht Ebenen
(der Einfachheit halber sollte die Ordnerstruktur
jedoch aus weniger als zwei Ebenen bestehen).
Abspielbare Ordner: bis zu 99
Abspielbare Dateien: bis zu 999
Dateisystem: Konformität mit ISO 9660 Stufe 1
und 2, Romeo, Joliet
Multi-Session-Wiedergabe: Kompatibel
Datenübertragungen im Paketverfahren: Nicht
kompatibel
Ungeachtet der Länge der Leerstellen, die die Ori-
ginalaufnahme zwischen den einzelnen Musikti-
teln aufweist, wird bei der Wiedergabe von
komprimierten Audio-Discs stets eine kurze Pause
zwischen den Titeln eingefügt.
VORSICHT
Bewahren Sie Discs nicht an Orten mit hohen
Temperaturen auf.
Reihenfolge der Audio-Dateien
Der Benutzer kann keine Ordnernummern zu-
weisen und auch die Wiedergabereihenfolge mit
diesem Gerät nicht bestimmen.
Beispiel einer Datenträger-Struktur
1
2
3
4
5
6
01
02
03
04
05
Stufe 1 Stufe 2 Stufe 3 Stufe 4
: Ordner
: Komprimierte
Audio-Datei
01 bis 05: Ordner-
nummer
1 bis 6: Wiederga-
bereihenfolge
Disc
Die bei der Ordnerauswahl oder einem anderen
Bedienvorgang angewendete Reihenfolge kann
sich je nach der verwendeten Codierungs- bzw.
Schreibsoftware ändern.
Russischer Zeichensatz
D: C D: C D: C D: C D: C
: А : Б : В : Г : Д
: Е, Ё : Ж : З : И, Й : К
: Л : М : Н : О : П
: Р : С : Т : У : Ф
D: C D: C D: C D: C D: C
: Х : Ц : Ч
: Ш,
Щ
: Ъ
: Ы : Ь : Э : Ю : Я
D: Anzeige C: Zeichen
Copyrights und Marken
iTunes
Apple und iTunes sind Warenzeichen von
Apple Inc., eingetragen in den USA und anderen
Ländern.
MP3
Die Bereitstellung dieses Produkts erfolgt in Ver-
bindung mit einer Lizenz zur privaten, nicht-
kommerziellen Nutzung und impliziert weder die
Übertragung einer Lizenz noch die Einräumung
eines Rechts zur Verwendung dieses Produkts
in kommerziellen (d. h. ertragsorientierten) Live-
Programmen (leitungsbasiert, per Satellit, Kabel
und/oder über jedes beliebige andere Medium),
zum Broadcasting/Streaming über das Internet,
über Intranets und/oder andere Netzwerke oder
in anderen elektronischen Inhalt-Vertriebssyste-
men, z. B. Pay-Audio- oder Audio-on-de-
mand-Anwendungen. Für eine derartige
Nutzung ist eine separate Lizenz erforderlich.
Detaillierte Informationen hierzu finden Sie
unter
http://www.mp3licensing.com.
WMA
Windows Media ist eine eingetragene Marke
oder eine Marke der Microsoft Corporation in
den USA und/oder anderen Ländern.
Dieses Produkt enthält Technologie, die Eigen-
tum der Microsoft Corporation ist und nicht
ohne Lizenz von Microsoft Licensing, Inc. vertrie-
ben werden darf.
Zusätzliche Informationen
68
Anhang
Zusätzliche Informationen
De
Black plate (69,1)
Technische Daten
Allgemein
Stromversorgung ............. 14,4 V Gleichspannung (Tole-
ranz 10,8 V bis 15,1 V)
Erdungssystem ................ Negativ
Maximale Leistungsaufnahme
................................... 10,0 A
Abmessungen (B × H × T):
DIN
Einbaugröße ...... 178 mm × 50mm ×
165 mm
Frontfläche ........ 188 mm × 58mm ×
16 mm
D
Einbaugröße ...... 178 mm × 50mm ×
165 mm
Frontfläche ........ 170 mm × 46mm ×
16 mm
Gewicht ........................... 1 kg
Audio
Max. Ausgangsleistung .... 50 W × 4
70 W × 1/2 W (für Subwoofer)
Dauer-Ausgangsleistung
................................... 22W × 4 (50Hz bis 15000 Hz,
5 % THD, bei 4-W-Last, beide
Kanäle betrieben)
Lastimpedanz .................. 4 W (4 W bis 8 W zulässig)
Maximaler Preout-Ausgangspegel
................................... 2,0V
Loudness-Kontur ............. +10 dB (100 Hz), +6,5 dB (10
kHz) (Lautstärke: 30 dB)
Equalizer (5-Band Graphic Equalizer):
Frequenz ................... 80Hz/250 Hz/800 Hz/
2,5 kHz/8 kHz
Entzerrungsbereich
............................ ±12 dB (Inkrement 2 dB)
Subwoofer (Mono):
Frequenz ................... 50Hz/63 Hz/80 Hz/100 Hz/
125 Hz/160 Hz/200 Hz
Steilheit .................... 6 dB/Okt., 12 dB/Okt.
Verstärkung .............. +6dB bis 24 dB
Phase ....................... Normal/Gegen
CD-Player
Typ ................................... Compact-Disc-Digital-Audio-
system
Kompatible Discs ............. Compact Disc
Signal-Rauschabstand ..... 94dB (1kHz) (IEC-A-Netz)
Anzahl der Kanäle ............ 2 (Stereo)
MP3-Decodiermodus ....... MPEG-1 und 2 Audio Layer 3
WMA-Decodiermodus ...... Vers. 7, 7.1, 8, 9, 10, 11, 12 (2-
Kanal-Audio)
(Windows Media Player)
WAV-Signalformat ............ Lineare PCM und MS ADPCM
(nicht komprimiert)
UKW-Tuner
Frequenzbereich .............. 87,5 MHz bis 108,0 MHz
Nutzempfindlichkeit ......... 9 dBf (0,8 µV/75 W, Mono, Sig-
nal-Rauschabstand: 30 dB)
Signal-Rauschabstand ..... 72dB (IEC-A-Netz)
MW-Tuner
Frequenzbereich .............. 531 kHz bis 1602kHz
Nutzempfindlichkeit ......... 25µV (Signal-Rauschabstand:
20 dB)
Signal-Rauschabstand ..... 62dB (IEC-A-Netz)
LW-Tuner
Frequenzbereich .............. 153 kHz bis 281 kHz
Nutzempfindlichkeit ......... 28µV (Signal-Rauschabstand:
20 dB)
Signal-Rauschabstand ..... 62dB (IEC-A-Netz)
Hinweis
Änderungen der technischen Daten und des De-
signs vorbehalten.
Deutsch
Zusätzliche Informationen
69
Anhang
De
Black plate (70,1)
Hartelijk dank voor uw keuze voor dit
Pioneer-product.
Lees deze handleiding voordat u het product in
gebruik neemt zodat u het goed leert gebruiken.
Lees vooral de gedeelten die met WAARSCHU-
WING en LET OP gemarkeerd zijn aandachtig.
Bewaar deze handleiding na het lezen op een vei-
lige, voor de hand liggende plaats zodat u hem in-
dien nodig altijd kunt raadplegen.
Deponeer dit product niet bij het gewone
huishoudelijk afval wanneer u het wilt verwij-
deren. Er bestaat een speciaal wettelijk voor-
geschreven verzamelsysteem voor de juiste
behandeling, het opnieuw bruikbaar maken
en de recycling van gebruikte elektronische
producten.
In de lidstaten van de EU en in Zwitserland en
Noorwegen kunnen particulieren afgedankte
elektronische producten gratis bij de daarvoor
bestemde verzamelplaatsen inleveren. Als u een
soortgelijk nieuw product koopt, kunt u het afge-
dankte product ook bij uw verkooppunt inleve-
ren.
Als u in een ander land woont, neem dan con-
tact op met de plaatselijke overheid voor infor-
matie over het weggooien van afgedankte
producten.
Op die manier zorgt u ervoor dat uw afgedankte
product op de juiste wijze wordt verwerkt, herge-
bruikt en gerecycled, zonder schadelijke gevol-
gen voor het milieu en de volksgezondheid.
Informatie over dit toestel
De tuner van dit toestel kan worden afgestemd
op frequenties die gebruikt worden in West-Eu-
ropa, Azië, het Midden-Oosten, Afrika en Ocea-
nië. In andere gebieden is de ontvangst wellicht
slecht. De RDS-functie (Radio Data System)
werkt alleen in gebieden waar FM-zenders RDS-
informatie uitzenden.
LET OP
Dit apparaat is geclassificeerd als een klasse
1 laserproduct onder de veiligheidsnormen
voor laserproducten, IEC 60825-1:2007.
KLASSE 1 LASERPRODUCT
LET OP
! Zorg ervoor dat het toestel niet met vloeistof
in aanraking komt. Een elektrische schok
kan daarvan het gevolg zijn. Bovendien kan
contact met vloeistoffen rookvorming, over-
verhitting en andere schade aan het toestel
veroorzaken.
! De Pioneer CarStereo-Pass wordt alleen in
Duitsland gebruikt.
! Zet het volume nooit zo hoog dat u geluiden
buiten het voertuig niet meer kunt horen.
! Zorg dat het toestel niet wordt blootgesteld
aan vocht.
! Als de accu wordt losgekoppeld of leeg
raakt, wordt het voorkeuzegeheugen gewist.
Opmerking
Instellingen worden ook uitgevoerd als u het
menu annuleert zonder te bevestigen.
Bij problemen
Als dit toestel niet naar behoren functioneert,
kunt u uw leverancier of het dichtstbijzijnde er-
kende Pioneer-servicecentrum raadplegen.
Vóór u begint
70
Hoofdstuk
Vóór u begint
Nl
01
Black plate (71,1)
Hoofdtoestel
b c
5
8
1 2 3 4 6
a9d7
Onderdeel Onderdeel
1 h (uitwerpen) 8 BAND
2 SRC/OFF 9
(terug)/DIM-
MER (dimmer)
3
MULTI-CONTROL
(M.C.)
a c/d
4
(lijst) b 1/ tot 6/
5 DISP c
AUX-ingang
(3,5 mm-stereo-
plug)
6
Laadsleuf voor
disc
d Verwijderen
7
(equalizer)
Display-indicaties
21 3 75
9
4 6 8
a
Indicator Status
1
(lijst) De lijst wordt bediend.
2
Bijkomende
informatie
Hier wordt bijkomende infor-
matie weergegeven.
3
TA (ver-
keersbe-
richten)
Automatische ontvangst van
verkeersberichten (TA) is inge-
schakeld.
4
TP (ver-
keerspro-
gramma-
identifica-
tie)
Er is afgestemd op een zender
met verkeersinformatie (TP-
zender).
5
(sound re-
triever)
De sound retriever is inge-
schakeld.
6 LOC
Automatisch afstemmen op
lokale zenders is ingescha-
keld.
7
(herha-
len)
Herhalen van een fragment of
map is ingeschakeld.
8
(wille-
keurig)
Willekeurige weergave is inge-
schakeld.
9
Basisinfor-
matie
! Tuner: frequentieband en
frequentie
! RDS: programmaservice-
naam, PTY-informatie en
andere tekstinformatie
! Cd-speler: verstreken
weergavetijd en tekstinfor-
matie
a
Licht op wanneer er een
menu of mappen op een
lager niveau bestaan.
Instellingenmenu
Als u het contact aanzet na de installatie, ver-
schijnt het instellingenmenu op het display.
U kunt de onderstaande menu-opties instellen.
1 Zet het contact aan na de installatie van
dit toestel.
SET UP verschijnt.
2 Draai aan M.C. en selecteer YES.
# Als u niet binnen 30 seconden een bediening uit-
voert, wordt het instellingenmenu niet weergegeven.
# Als u op dit moment geen instellingen wilt
maken, draait u M.C. naar NO. Indrukken om te se-
lecteren.
Als u NO selecteert, kunt u geen instellingen maken
in het instellingenmenu.
3 Druk op M.C. om uw keuze te bevesti-
gen.
4 Voer de volgende procedures uit om het
menu in te stellen.
Om verder te gaan naar de volgende menu-
optie, moet u uw selectie bevestigen.
LANGUAGE (taalinstelling)
Dit toestel kan Engelse of Russische tekstinforma-
tie bij een gecomprimeerd audiobestand weerge-
ven.
! Als de gebruikte taal niet overeenkomt met de
taalinstelling van dit toestel, wordt tekst wel-
licht niet correct weergegeven.
! Het is mogelijk dat sommige tekens niet juist
worden weergegeven.
1 Draai aan M.C. en selecteer de gewenste in-
stelling.
ENG (Engels)РУС (Russisch)
2 Druk op M.C. om de selectie te bevestigen.
CLOCK SET (klok)
1 Draai aan M.C. om het uur in te stellen.
2 Druk op M.C. om de minuut te selecteren.
3 Draai aan M.C. om de minuut in te stellen.
4 Druk op M.C. om de selectie te bevestigen.
FM STEP (FM-afstemstap)
Standaard wordt er bij automatisch afstemmen
een FM-afstemstap van 50 kHz gebruikt, en
100 kHz als de functie AF of TA is ingeschakeld.
Maar soms krijgt u een beter resultaat als ook bij
het afstemmen op alternatieve frequenties (AF)
een afstemstap van 50 kHz wordt gebruikt.
! Bij handmatig afstemmen blijft de afstemstap
50 kHz.
1 Draai aan M.C. en selecteer de FM-afstemstap.
50 (50 kHz)100 (100 kHz)
2 Druk op M.C. om de selectie te bevestigen.
QUIT verschijnt.
5 Draai aan M.C. en selecteer YES om de in-
stelling te voltooien.
# Als u de instelling wilt wijzigen, draait u M.C.
naar NO. Druk in om te selecteren.
6 Druk op M.C. om uw keuze te bevesti-
gen.
Opmerkingen
! U kunt de menu-opties instellen in het sys-
teemmenu. Raadpleeg Systeemmenu op
bladzijde 75 voor meer informatie over de in-
stellingen.
! U kunt het instellingenmenu annuleren door
op SRC/OFF te drukken.
Basisbediening
Belangrijk
! Wees voorzichtig bij het verwijderen en te-
rugplaatsen van het voorpaneel.
! Stel het voorpaneel niet bloot aan schokken.
Nederlands
Bediening van het toestel
71
Hoofdstuk
Bediening van het toestel
Nl
02
Black plate (72,1)
! Stel het voorpaneel niet bloot aan direct zon-
licht en hoge temperaturen.
! Maak eerst alle kabels en apparaten (indien
aanwezig) van het voorpaneel los voordat u
het verwijdert om beschadiging aan het toe-
stel en het voertuiginterieur te voorkomen.
Het voorpaneel tegen diefstal verwijderen
1 Druk op de toets Verwijderen om het voorpa-
neel los te maken.
2 Duw het voorpaneel naar boven (M) en trek het
naar u toe (N).
3 Bewaar het losgemaakte voorpaneel in een be-
schermend omhulsel zoals een stevig doosje.
Het voorpaneel terugzetten
1 Schuif het voorpaneel naar links.
Steek de lipjes aan de linkerzijde van het
hoofdtoestel goed in de openingen in het voor-
paneel.
2 Druk de rechterzijde van het voorpaneel aan
tot het goed geplaatst is.
Als het niet lukt het voorpaneel te bevestigen,
controleer dan of u het wel juist op het hoofd-
toestel bevestigt. Gebruik geen kracht want
daardoor kunt u het paneel en het toestel be-
schadigen.
Het toestel inschakelen
1 Druk op SRC/OFF om het toestel in te schake-
len.
Het toestel uitschakelen
1 Houd SRC/OFF ingedrukt tot het toestel uit
gaat.
Een signaalbron selecteren
1 Druk op SRC/OFF om over te schakelen tus-
sen:
TUNER (tuner)CD (cd-speler)AUX (AUX)
Het volume afstellen
1 Draai aan M.C. om het volume te regelen.
LET OP
Voor uw veiligheid en die van anderen moet u
het voertuig eerst parkeren als u het voorpaneel
wilt verwijderen.
Opmerking
Als de blauw-witte draad van dit toestel is aange-
sloten op de bedieningsaansluiting van de auto-
matische antenne van het voertuig, schuift de
antenne uit wanneer er een signaalbron van dit
toestel wordt ingeschakeld. Als de signaalbron
wordt uitgeschakeld, wordt de antenne weer in-
geschoven.
Veelgebruikte menufuncties
Terugkeren naar het vorige display
Terugkeren naar de vorige lijst (de map die een ni-
veau hoger ligt)
1 Druk op
/DIMMER.
Terugkeren naar het gewone display
Het hoofdmenu annuleren
1 Druk op BAND.
Terugkeren naar het gewone display van de lijst
1 Druk op BAND.
Tuner
Basisbediening
Een frequentieband selecteren
1 Druk op BAND totdat de gewenste frequentie-
band (FM1, FM2, FM3 voor FM of MW/LW)
wordt weergegeven.
Overschakelen tussen voorkeuzestations
1 Druk op c of d.
! Om deze functie te gebruiken, moet u PCH
(voorkeuzezender) selecteren onder SEEK.
Raadpleeg voor meer informatie over de instel-
lingen SEEK (instelling linker/rechter toets) op
de volgende bladzijde.
Handmatig afstemmen (stap voor stap)
1 Druk op c of d.
! Om deze functie te gebruiken, moet u MAN
(handmatig afstemmen) selecteren onder
SEEK. Raadpleeg voor meer informatie over de
instellingen SEEK (instelling linker/rechter
toets) op de volgende bladzijde.
Automatisch afstemmen
1 Houd c of d ingedrukt en laat deze weer los.
U kunt het automatisch afstemmen afbreken
door even op c of d te drukken.
Als u c of d ingedrukt houdt, worden zenders
overgeslagen. Het automatisch afstemmen be-
gint zodra u c of d loslaat.
Opmerking
U kunt de AF-functie (zoeken naar alternatieve
frequenties) in- en uitschakelen. Voor normaal
afstemmen moet de AF-functie uit staan (raad-
pleeg AF (alternatieve frequenties zoeken) op de
volgende bladzijde).
Zenders voor de verschillende
frequentiebanden opslaan en
oproepen
De voorkeuzetoetsen gebruiken
1 Stem af op de zender die u in het geheu-
gen wilt opslaan. Om hem op te slaan houdt
u de gewenste voorkeuzetoets (1/
t/m 6/
) ingedrukt tot het voorkeuzenummer
stopt met knipperen.
2 Druk op de gewenste voorkeuzetoets (1/
t/m 6/ ) om de betreffende zender te se-
lecteren.
Een ander display kiezen
De gewenste informatie selecteren
1 Druk op DISP om over te schakelen tussen:
! FREQUENCY (programmaservicenaam of
frequentie)
! BRDCST INFO (programmaservicenaam/
PTY-informatie)
! CLOCK (naam signaalbron en klok)
Opmerkingen
! Als de programmaservicenaam niet gedetec-
teerd kan worden in FREQUENCY, wordt de
frequentie weergegeven. Anders wordt de
programmaservicenaam weergegeven.
! De tekstinformatie onder BRDCST INFO
wordt automatisch bijgewerkt.
! Afhankelijk van de frequentieband kan de
tekstinformatie verschillen.
! Welke tekstinformatie gewijzigd kan worden,
hangt af van het gebied.
PTY-functies
Met behulp van PTY-informatie (programmatype-
informatie) kunt u op een bepaald soort zender
afstemmen.
Bediening van het toestel
72
Hoofdstuk
Bediening van het toestel
Nl
02
Black plate (73,1)
RDS-zenders zoeken via PTY-informatie
U kunt naar bepaalde soorten uitzendingen zoe-
ken, zoals de uitzendingen die in het volgende ge-
deelte worden genoemd: deze bladzijde.
1 Druk op
(lijst).
2 Draai aan M.C. om een programmatype te kie-
zen.
NEWS/INFOPOPULARCLASSICS
OTHERS
3 Druk op M.C. om het zoeken te beginnen.
Het toestel zoekt naar een zender die het gese-
lecteerde programmatype uitzendt. Als er een
zender is gevonden, wordt de programmaservi-
cenaam weergegeven.
! Druk opnieuw op M.C. om het zoeken te
annuleren.
! Het programma van een zender kan afwij-
ken van de informatie die door de PTY-code
wordt aangegeven.
! Als er geen zender gevonden wordt die het
gewenste soort programma uitzendt, wordt
op het display ongeveer twee seconden
lang NOT FOUND getoond en keert de
tuner terug naar de oorspronkelijke zender.
PTY-lijst
NEWS/INFO (nieuws en informatie)
NEWS (nieuws), AFFAIRS (actualiteiten), INFO (in-
formatie), SPORT (sport), WEATHER (weer), FI-
NANCE (financieel nieuws)
POPULAR (populaire muziek)
POP MUS (populaire muziek), ROCK MUS (rock-
muziek), EASY MUS (lichte muziek), OTH MUS
(andere muziek), JAZZ (jazz), COUNTRY (country-
muziek), NAT MUS (nationale muziek), OLDIES
(Gouwe Ouwe), FOLK MUS (folkmuziek)
CLASSICS (klassieke muziek)
L. CLASS (lichte klassieke muziek), CLASSIC (klas-
sieke muziek)
OTHERS (andere)
EDUCATE (educatief), DRAMA (theater), CUL-
TURE (cultuur), SCIENCE (wetenschap), VARIED
(varia), CHILDREN (kinderprogrammas), SOCIAL
(praatprogrammas), RELIGION (religieus),
PHONE IN (inbelprogrammas), TOURING (rei-
zen), LEISURE (ontspanning), DOCUMENT (docu-
mentaires)
Functie-instellingen
1 Druk op M.C. om het hoofdmenu weer te
geven.
2 Draai aan M.C., selecteer de menuoptie
FUNCTION en druk erop.
3 Draai aan M.C. om de gewenste functie
te selecteren.
U kunt de volgende functies aanpassen.
# Als de MW/LW-band is geselecteerd, zijn alleen
BSM, LOCAL en SEEK beschikbaar.
BSM (geheugen voor de sterkste zenders)
Met de functie BSM (Best Stations Memory) kunt
u automatisch de zes sterkste zenders in het ge-
heugen opslaan. Deze worden opgeslagen in volg-
orde van signaalsterkte.
1 Druk op M.C. om de functie BSM in te schake-
len.
Druk nogmaals op M.C. om deze te annuleren.
REGION (regionaal)
Als de functie AF is ingeschakeld, kan de regio-
nale functie gebruikt worden om het zoeken tot re-
gionale programmas te beperken.
1 Druk op M.C. om de regionale functie in of uit
te schakelen.
LOCAL (automatisch afstemmen op lokale zen-
ders)
Als deze functie is ingeschakeld, stemt het toestel
alleen af op zenders waarvan het signaal vol-
doende sterk is voor een goede ontvangst.
1 Druk op M.C. en selecteer de gewenste instel-
ling.
FM: OFFLV1LV2LV3LV 4
MW/LW: OFFLV1 LV2
Als u het hoogste niveau selecteert, wordt al-
leen afgestemd op de sterkste zenders. Bij la-
gere niveaus wordt ook afgestemd op
zwakkere zenders.
TA (stand-by voor verkeersberichten)
1 Druk op M.C. om de functie Stand-by voor ver-
keersberichten in en uit te schakelen.
AF (alternatieve frequenties zoeken)
1 Druk op M.C. om AF aan of uit te zetten.
NEWS (onderbreking door nieuwsberichten)
1 Druk op M.C. om de nieuwsfunctie in of uit te
schakelen.
SEEK (instelling linker/rechter toets)
U kunt een functie toewijzen aan de linker en rech-
ter toets van het toestel.
Selecteer MAN (handmatig afstemmen) om hand-
matig af te stemmen of PCH (voorkeuzezenders)
om op voorkeuzezenders af te stemmen.
1 Druk op M.C. om MAN of PCH te selecteren.
Cd/cd-r/cd-rw-discs
Basisbediening
Een cd/cd-r/cd-rw afspelen
1 Plaats een disc met het etiket omhoog in de
laadsleuf.
Een cd/cd-r/cd-rw uitwerpen
1 Druk op h.
Een map selecteren
1 Druk op 1/
of 2/ .
Een fragment selecteren
1 Druk op c of d.
Vooruit of achteruit spoelen
1 Houd c of d ingedrukt.
! Als u gecomprimeerde audio afspeelt, is er
geen geluid bij vooruit- en achteruitspoelen.
Terugkeren naar de hoofdmap
1 Houd BAND ingedrukt.
Overschakelen tussen gecomprimeerde audio en
cd-da
1 Druk op BAND.
Een ander display kiezen
De gewenste informatie selecteren
1 Druk op DISP om over te schakelen tussen:
CD-DA
! ELAPSED TIME (fragmentnummer en
weergavetijd)
! CLOCK (naam signaalbron en klok)
! SPEANA (spectrumanalyzer)
CD-TEXT
! TRACK INFO (fragmenttitel/naam artiest
fragment/disctitel)
! ELAPSED TIME (fragmentnummer en
weergavetijd)
! CLOCK (naam signaalbron en klok)
! SPEANA (spectrumanalyzer)
MP3/WMA/WAV
! TRACK INFO (fragmenttitel/naam artiest/
albumtitel)
! FILE INFO (bestandsnaam/mapnaam)
! ELAPSED TIME (fragmentnummer en
weergavetijd)
! CLOCK (naam signaalbron en klok)
! SPEANA (spectrumanalyzer)
Nederlands
Bediening van het toestel
73
Hoofdstuk
Bediening van het toestel
Nl
02
Black plate (74,1)
Opmerkingen
! De tekstinformatie onder TRACK INFO en
FILE INFO wordt automatisch bijgewerkt.
! Afhankelijk van het mediabestandstype en
de versie van iTunes waarmee MP3-bestan-
den op de disc zijn opgenomen, kan het voor-
komen dat incompatibele tekst bij een
audiobestand niet goed wordt weergegeven.
! Welke tekstinformatie gebruikt kan worden,
hangt af van de informatiedrager.
Bestanden en fragmenten in de
lijst selecteren en afspelen
1 Druk op om over te schakelen naar de
lijst met bestands- of fragmentnamen.
2 Gebruik M.C. om de gewenste bestands-
naam (of mapnaam) te selecteren.
Een bestand of map selecteren
1 Draai aan M.C.
Afspelen
1 Selecteer een bestand of fragment en druk op
M.C.
Een lijst van de bestanden (mappen) in de gese-
lecteerde map weergeven
1 Selecteer een map en druk op M.C.
Een song in de geselecteerde map afspelen
1 Selecteer een map en houd M.C. ingedrukt.
Bediening met speciale toetsen
Een herhaalbereik selecteren
1 Druk op 6/
om over te schakelen tussen:
! ALL Alle fragmenten herhalen
! ONE Het huidige fragment herhalen
! FLD De huidige map herhalen
Fragmenten in willekeurige volgorde afspelen
1 Druk op 5/
om willekeurige weergave in of
uit te schakelen.
Fragmenten in een geselecteerd herhaalbereik
worden in willekeurige volgorde afgespeeld.
! Druk tijdens weergave in willekeurige volgorde
op d om naar het volgende fragment te gaan.
Als u op c drukt, wordt het huidige fragment
opnieuw vanaf het begin afgespeeld.
Het afspelen onderbreken
1 Druk op 4/PAUSE om het afspelen te onderbre-
ken (pauze) of te hervatten.
De geluidskwaliteit van gecomprimeerde audio
verbeteren (sound retriever)
1 Druk op 3/S.Rtrv om over te schakelen tussen:
12OFF (uit)
1 heeft effect bij lage compressie en 2 heeft ef-
fect bij hoge compressie.
Functie-instellingen
1 Druk op M.C. om het hoofdmenu weer te
geven.
2 Draai aan M.C., selecteer de menuoptie
FUNCTION en druk erop.
U kunt de volgende functie aanpassen.
S.RTRV (sound retriever)
Deze verbetert automatisch de weergave van ge-
comprimeerde audio en zorgt voor een vol geluid.
1 Druk op M.C. en selecteer de gewenste instel-
ling.
Raadpleeg De geluidskwaliteit van gecompri-
meerde audio verbeteren (sound retriever) op
deze bladzijde voor meer informatie.
Audio-instellingen
1 Druk op M.C. om het hoofdmenu weer te
geven.
2 Draai aan M.C., selecteer de menuoptie
AUDIO en druk erop.
3 Draai aan M.C. en selecteer de audiofunc-
tie.
U kunt de volgende audiofuncties aanpassen.
! FADER kan niet worden gebruikt als
SUB.W/SUB.W is geselecteerd in
SP-P/O MODE. Raadpleeg voor meer infor-
matie SP-P/O MODE (achteruitgang en
preout-instelling) op bladzijde 76.
! SUB.W, SUB.W CTRL en HPF SETTING kun-
nen niet worden gebruikt als REAR/REAR is
geselecteerd in SP-P/O MODE. Raadpleeg
voor meer informatie SP-P/O MODE (achter-
uitgang en preout-instelling) op bladzijde 76.
! SUB.W CTRL en HPF SETTING kunnen niet
worden gebruikt als SUB.W is geselecteerd in
OFF. Raadpleeg voor meer informatie SUB.W
(subwoofer aan/uit) op de volgende bladzijde.
FADER (fader aanpassen)
1 Druk op M.C. om de instellingenmodus weer
te geven.
2 Draai aan M.C. om de balans tussen de luid-
sprekers voorin en achterin in te stellen.
BALANCE (balansinstelling)
1 Druk op M.C. om de instellingenmodus weer
te geven.
2 Draai aan M.C. om de balans tussen de linker/
rechterluidsprekers in te stellen.
EQ SETTING (equalizercurven)
1 Druk op M.C. om de instellingenmodus weer
te geven.
2 Draai aan M.C. om de equalizer te selecteren.
POWERFULNATURALVOCALCUS-
TOM1CUSTOM2FLATSUPER BASS
De equalizerband en het equalizerniveau kun-
nen worden aangepast van CUSTOM1 en
CUSTOM2.
Volg de onderstaande procedure als u CUS-
TOM1 of CUSTOM2 selecteert. Voor een an-
dere optie drukt u op M.C. om terug te keren
naar het vorige display.
! CUSTOM1 kan voor elke signaalbron af-
zonderlijk ingesteld worden.
! CUSTOM2 is een gemeenschappelijk in-
stelling voor alle signaalbronnen.
3 Druk op M.C. om de instellingenmodus weer
te geven.
4 Druk op M.C. om over te schakelen tussen:
EqualizerbandEqualizerniveau
5 Draai aan M.C. en selecteer de gewenste in-
stelling.
Equalizerband: 80HZ250HZ800HZ
2.5KHZ8KHZ
Equalizerniveau: +6 tot 6
! U kunt ook tussen de equalizers overschakelen
door op
te drukken.
LOUDNESS (loudness)
De loudness-functie compenseert een tekort aan
lage tonen en hoge tonen bij een laag volume.
1 Druk op M.C. en selecteer de gewenste instel-
ling.
OFF (uit)LOW (laag)MID (midden)HI
(hoog)
Bediening van het toestel
74
Hoofdstuk
Bediening van het toestel
Nl
02
Black plate (75,1)
SUB.W (subwoofer aan/uit)
Dit toestel is voorzien van een in- en uitschakel-
bare subwooferuitgang.
1 Druk op M.C. en selecteer de gewenste instel-
ling.
NOR (normale fase)REV (tegengestelde
fase)OFF (subwoofer uit)
SUB.W CTRL (subwoofer aanpassen)
De subwoofer geeft alleen frequenties beneden de
geselecteerde waarde weer.
1 Druk op M.C. om de instellingenmodus weer
te geven.
2 Druk op M.C. om over te schakelen tussen:
DrempelfrequentieUitgangsniveauVerval-
niveau
Instelbare waarden knipperen.
3 Draai aan M.C. en selecteer de gewenste in-
stelling.
Drempelfrequentie: 50HZ63HZ80HZ
100HZ125HZ160HZ200HZ
Uitgangsniveau: 24 tot +6
Hellingsniveau: 6 12
BASS BOOST (bass boost)
1 Druk op M.C. om de instellingenmodus weer
te geven.
2 Draai aan M.C. en selecteer het gewenste ni-
veau.
U kunt het niveau verhogen of verlagen tussen
de waarden 0 en +6. De waarde wordt op het
display getoond.
HPF SETTING (high pass filter aanpassen)
Als u wilt dat de luidsprekers voorin of achterin
geen lage tonen (uit het frequentiebereik van de
subwoofer) weergeven, kunt u het high pass filter
(HPF) aanzetten. Alleen frequenties boven het ge-
selecteerde bereik worden dan weergegeven door
de voor- of achterluidsprekers.
1 Druk op M.C. om de instellingenmodus weer
te geven.
2 Druk op M.C. om over te schakelen tussen:
DrempelfrequentieVervalniveau
3 Draai aan M.C. en selecteer de gewenste in-
stelling.
Drempelfrequentie: OFF50HZ63HZ
80HZ100HZ125HZ160HZ200HZ
Hellingsniveau: 6 12
SLA (bronniveauregeling)
Met de functie SLA (bronniveauregeling) kunt u
het volumeniveau van elke signaalbron afzonder-
lijk instellen. Hierdoor kunt u plotselinge volume-
wisselingen voorkomen wanneer naar een andere
signaalbron wordt overgeschakeld.
! De instellingen zijn gebaseerd op het FM-volu-
meniveau, dat zelf niet gewijzigd kan worden.
! Het MW/LW-volumeniveau kan ook met deze
functie worden aangepast.
! Wanneer FM als signaalbron wordt gebruikt,
kunt u niet overschakelen naar SLA.
1 Druk op M.C. om de instellingenmodus weer
te geven.
2 Draai aan M.C. om het bronvolume te regelen.
Instelbereik: +4 tot 4
Systeemmenu
Belangrijk
Als het toestel van de accu wordt losgekoppeld,
wordt PW SAVE (energiezuinige modus) uitge-
schakeld. Deze functie moet u weer inschakelen
als het toestel terug met de accu wordt verbon-
den. Als het voertuig niet van een contactscha-
kelaar met accessoirestand (ACC) is voorzien, is
het (afhankelijk van de aansluiting) mogelijk dat
het toestel de accu blijft belasten als PW SAVE
(energiezuinige modus) is uitgeschakeld.
1 Druk op M.C. om het hoofdmenu weer te
geven.
2 Draai aan M.C., selecteer de menuoptie
SYSTEM en druk erop.
3 Draai aan M.C. en selecteer de systeem-
menufunctie.
U kunt de volgende functies in het systeemme-
nu aanpassen.
LANGUAGE (taalinstelling)
Dit toestel kan Engelse of Russische tekstinforma-
tie bij een gecomprimeerd audiobestand weerge-
ven.
! Als de gebruikte taal niet overeenkomt met de
taalinstelling van dit toestel, wordt tekst wel-
licht niet correct weergegeven.
! Het is mogelijk dat sommige tekens niet juist
worden weergegeven.
1 Draai aan M.C. en selecteer de gewenste in-
stelling.
ENG (Engels)РУС (Russisch)
CLOCK SET (klok)
1 Druk op M.C. om de instellingenmodus weer
te geven.
2 Druk op M.C. om het onderdeel van de klok te
selecteren dat u wilt instellen.
UurMinuut
3 Draai aan M.C. om de klok in te stellen.
12H/24H (tijdweergave)
1 Druk op M.C. en selecteer de gewenste instel-
ling.
12H (12-uurs klok)24H (24-uurs klok)
AUTO PI (automatisch PI-zoeken)
Als deze functie is ingeschakeld, probeert het toe-
stel bij slechte ontvangst automatisch een andere
zender met gelijkaardige programmas te vinden,
ook als u een voorkeuzezender selecteerde.
1 Druk op M.C. om de automatische PI-zoek-
functie in of uit te schakelen.
AUX (externe aansluiting)
Schakel deze instelling in als een extern apparaat
op dit toestel is aangesloten.
1 Druk op M.C. om AUX in of uit te schakelen.
MUTE MODE (dempen)
Het geluid van dit toestel kan automatisch worden
uitgeschakeld of gedempt wanneer een ander ap-
paraat met uitschakelingsfunctie daarom vraagt
met een speciaal signaal.
1 Druk op M.C. om de instellingenmodus weer
te geven.
2 Draai aan M.C. en selecteer de gewenste in-
stelling.
U kunt een van de opties in de volgende lijst
selecteren.
! MUTE Tijdelijk uitschakelen
! 20dB ATT Dempen (20dB ATT heeft
meer effect dan 10dB ATT)
! 10dB ATT Dempen
PW SAVE (energiezuinige stand)
Met deze functie wordt het energieverbruik van de
accu verminderd.
! Als deze functie is ingeschakeld, kan alleen
het bronsignaal worden ingeschakeld.
1 Druk op M.C. om de energiezuinige modus in
of uit te schakelen.
Nederlands
Bediening van het toestel
75
Hoofdstuk
Bediening van het toestel
Nl
02
Black plate (76,1)
De dimmer in- of uitschakelen
U kunt de helderheid van de verlichting aanpas-
sen.
1 Druk op M.C. om het hoofdmenu weer te
geven.
2 Draai aan M.C., geef ILLUMI weer en
druk erop.
3 Druk op M.C. en selecteer de gewenste
instelling.
OFF (uit)ON (aan)
! U kunt de dimmer ook instellen door
/DIMMER even ingedrukt te houden.
Beginmenu
1 Houd SRC/OFF ingedrukt tot het toestel
uit gaat.
2 Houd SRC/OFF ingedrukt tot het hoofd-
menu wordt weergegeven.
3 Draai aan M.C., selecteer de menuoptie
INITIAL en druk erop.
4 Draai aan M.C. en selecteer de gewenste
functie.
U kunt de volgende functies in het beginmenu
aanpassen.
FM STEP (FM-afstemstap)
Standaard wordt er bij automatisch afstemmen
een FM-afstemstap van 50 kHz gebruikt, en
100 kHz als de functie AF of TA is ingeschakeld.
Maar soms krijgt u een beter resultaat als ook bij
het afstemmen op alternatieve frequenties (AF)
een afstemstap van 50 kHz wordt gebruikt.
! Bij handmatig afstemmen blijft de afstemstap
50 kHz.
1 Druk op M.C. om de FM-afstemstap te selecte-
ren.
50 (50 kHz)100 (100 kHz)
SP-P/O MODE (achteruitgang en preout-instel-
ling)
Op de uitgang voor de achterluidspreker en de
RCA-uitgang van dit toestel kan een luidspreker
met volledig bereik of een subwoofer aangesloten
worden. Selecteer de gewenste instelling.
1 Druk op M.C. om de instellingenmodus weer
te geven.
2 Draai aan M.C. en selecteer de gewenste in-
stelling.
U kunt een van de opties in de volgende lijst
selecteren.
! REAR/SUB.W Selecteer deze stand als
op de uitgang voor de achterluidspreker
een luidspreker met volledig bereik aange-
sloten is, en op de RCA-uitgang een sub-
woofer aangesloten is.
! SUB.W/SUB.W Selecteer deze stand als
op de uitgang voor de achterluidspreker
een subwoofer rechtstreeks aangesloten is
zonder versterker, en op de RCA-uitgang
een subwoofer is aangesloten.
! REAR/REAR Selecteer deze stand als op
de uitgang voor de achterluidspreker en op
de RCA-uitgang een luidspreker met volle-
dig bereik is aangesloten.
Als op de uitgang voor de achterluidspre-
ker een luidspreker met volledig bereik is
aangesloten en de RCA-uitgang niet ge-
bruikt wordt, kunt u zowel REAR/SUB.W
als REAR/REAR selecteren.
Systeemmenu
1 Houd SRC/OFF ingedrukt tot het toestel
uit gaat.
2 Houd SRC/OFF ingedrukt tot het hoofd-
menu wordt weergegeven.
3 Draai aan M.C., selecteer de menuoptie
SYSTEM en druk erop.
4 Draai aan M.C. en selecteer de systeem-
menufunctie.
U kunt de volgende functies in het systeemme-
nu aanpassen.
Raadpleeg Systeemmenu op de vorige bladzijde
voor meer informatie.
De AUX-signaalbron
1 Steek de stereo-miniplugkabel in de
AUX-ingang van dit toestel.
2 Druk op SRC/OFF en kies AUX als signaal-
bron.
Opmerking
De signaalbron AUX kan alleen worden geselec-
teerd als de externe aansluiting is ingeschakeld.
Raadpleeg voor meer informatie AUX (externe
aansluiting) op de vorige bladzijde.
Een ander display kiezen
De gewenste informatie selecteren
1 Druk op DISP om over te schakelen tussen:
! Naam signaalbron
! Naam signaalbron en klok
Als een scherm verkeerd
wordt weergegeven
Zet het ongewenste scherm als volgt uit.
1 Druk op M.C. om het hoofdmenu weer te
geven.
2 Draai aan M.C., selecteer de menuoptie
SYSTEM en druk erop.
3 Draai aan M.C., geef DEMO OFF weer en
druk erop.
4 Draai aan M.C. en selecteer YES.
5 Druk op M.C. om uw keuze te bevesti-
gen.
Bediening van het toestel
76
Hoofdstuk
Bediening van het toestel
Nl
02
Black plate (77,1)
Verbindingen
Belangrijk
! Als dit toestel wordt geïnstalleerd in een voer-
tuig met een contactschakelaar zonder ACC-
stand (accessoirestand), kan de accu leeglo-
pen als de rode kabel niet wordt aangesloten
op de aansluiting die de bediening van de
contactschakelaar herkent.
O
N
S
T
A
R
T
O
F
F
ACC-stand Geen ACC-stand
! Gebruik van dit toestel onder andere omstan-
digheden dan de volgende kan leiden tot
brand of storingen.
Voertuigen met een accu van 12 volt en nega-
tieve aarding.
Luidsprekers van 50 W (uitgangswaarde) en
4 W tot 8 W (impedantiewaarde).
! Om kortsluiting, oververhitting en storingen
te voorkomen, moet u onderstaande aanwij-
zingen opvolgen.
Koppel de negatieve aansluiting van de accu
los voordat u het toestel installeert.
Gebruik kabelklemmen of plakband om de
bekabeling veilig aan te brengen. Bescherm
de kabels met plakband op plaatsen waar
deze tegen metalen onderdelen liggen.
Plaats geen kabels in de buurt van beweeg-
bare onderdelen zoals de versnellingspook of
de stoelrails.
Leg kabels niet op plaatsen die heet kunnen
worden, zoals dicht bij de kachel.
Sluit de gele kabel niet op de accu aan via
een gat in het motorcompartiment.
Dek alle ongebruikte kabelaansluitingen af
met isolatietape.
Maak de kabels niet korter.
Verwijder nooit de isolatie van de voedingska-
bel van dit toestel om andere apparaten van
stroom te voorzien. De stroomcapaciteit van
de voedingskabel is beperkt.
Gebruik een zekering met het voorgeschreven
vermogen.
Verbind de negatieve luidsprekerkabel nooit
rechtstreeks met de aarding.
Voeg de negatieve kabels van verschillende
luidsprekers nooit samen.
! Als dit apparaat aan staat, wordt het bedie-
ningssignaal doorgegeven via de blauw/witte
kabel. Verbind deze kabel met de afstandsbe-
diening van een externe versterker of met de
bedieningsaansluiting van de automatische
antenne van het voertuig (maximaal 300 mA,
12 V gelijkstroom). Als het voertuig is uitge-
rust met een glasantenne, verbindt u deze
met de voedingsaansluiting van de antenne-
booster.
! Verbind de blauw/witte kabel nooit met de
voedingsaansluiting van een externe verster-
ker of automatische antenne. Anders kan de
accu leeglopen of kan er storing optreden.
! De zwarte kabel is de aarding. Dit toestel
moet gescheiden worden geaard van andere
apparaten (met name apparaten die veel
stroom verbruiken zoals een versterker). An-
ders kan er brand of storing ontstaan wan-
neer de aarding per ongeluk losraakt.
Dit toestel
3 45
21
1 Ingang stroomkabel
2 Achteruitgang of subwooferuitgang
3 Antenne-ingang
4 Zekering (10 A)
5 Ingang voor draadafstandsbediening
Een bedrade afstandsbedieningsadapter kan
aangesloten worden (los verkrijgbaar).
Stroomkabel
1
3
3
2
4
4
5
5
6
6
b
8
9
7
a
e
d
c
1 Naar ingang stroomkabel
2 De functie van 3 en 5 kan verschillen af-
hankelijk van het type voertuig. Verbind in
dat geval 4 met 5 en 6 met 3.
3 Geel
Back-up (of accessoire)
4 Geel
Aansluiten op de constante 12 V-voedings-
aansluiting.
5 Rood
Accessoire (of back-up)
6 Rood
Aansluiten op een aansluiting die door de
contactschakelaar wordt aangestuurd (12 V
gelijkstroom).
7 Verbind kabels van dezelfde kleur met elkaar.
8 Zwart (chassisaarding)
9 Blauw-wit
De pinpositie van de ISO-connector verschilt
naargelang het type voertuig. Als pin 5 de an-
tenne aanstuurt, verbindt u 9 en b. In an-
dere typen voertuigen verbindt u 9 en b
nooit.
a Blauw-wit
Aansluiten op systeembedieningsaansluiting
van de versterker (maximaal 300 mA, 12 V ge-
lijkstroom).
b Blauw-wit
Aansluiten op bedieningsaansluiting van de
gemotoriseerde antenne (maximaal 300 mA,
12 V gelijkstroom).
c Geel/zwart
Als u apparatuur met dempingsfunctie ge-
bruikt, verbindt u deze draad met de draad
voor audiodemping op die apparatuur. Als u
zulke apparatuur niet gebruikt, verbindt u de
draad voor audiodemping niet.
d Luidsprekerkabels
Wit: Linksvoor +
Wit-zwart: Linksvoor *
Grijs: Rechtsvoor +
Grijs-zwart: Rechtsvoor *
Groen: Linksachter + of subwoofer +
Groen-zwart: Linksachter * of subwoofer *
Violet: Rechtsachter + of subwoofer +
Violet-zwart: Rechtsachter * of subwoofer *
e ISO-connector
Bij sommige voertuigen is de ISO-connector
in twee verdeeld. Verbind in dat geval beide
connectoren.
Opmerkingen
! Wijzig het beginmenu van het toestel. Raad-
pleeg gedeelte SP-P/O MODE (achteruitgang
en preout-instelling) op de vorige bladzijde.
De subwooferuitgang van dit toestel is mono.
! Als u een subwoofer van 70 W (2 W) gebruikt,
moet u de subwoofer aansluiten op de vio-
lette en zwart-violette draden van dit toestel.
Sluit niets aan op de groene en groen-zwarte
draden.
Nederlands
Installatie
77
Hoofdstuk
Installatie
Nl
03
Black plate (78,1)
Versterker (apart verkrijgbaar)
Maak deze verbindingen als de optionele verster-
ker wordt gebruikt.
1
3
2
4
55
1 Systeemafstandsbediening
Verbinden met blauw-witte kabel.
2 Versterker (apart verkrijgbaar)
3 Aansluiten op RCA-kabels (apart verkrijg-
baar)
4 Naar achteruitgang of subwooferuitgang
5 Luidspreker achterin of subwoofer
Installatie
Belangrijk
! Controleer alle aansluitingen en systemen
voordat u de installatie voltooit.
! Gebruik geen onderdelen van andere fabri-
kanten; deze kunnen storingen veroorzaken.
! Neem contact op met uw dealer als er voor
de installatie gaten moeten worden geboord
of als er andere aanpassingen aan het voer-
tuig nodig zijn.
! Installeer dit toestel niet op een plaats waar:
het de besturing van het voertuig kan belem-
meren.
het de inzittenden kan verwonden bij een
noodstop.
! De halfgeleiderlaser raakt bij oververhitting
beschadigd. Plaats dit apparaat niet op plaat-
sen waar het warm wordt, zoals nabij de uit-
laat van een kachel.
! Dit toestel werkt het beste als het wordt ge-
plaatst onder een hoek van minder dan 60°.
60°
! Laat bij het plaatsen voldoende ruimte vrij
achter het achterpaneel en wikkel losse ka-
bels zo dat ze de ventilatiegaten niet blokke-
ren; zorg altijd dat warmte goed wordt
afgevoerd tijdens gebruik van het toestel.
5cmcm
Laat voldoende
ruimte vrij
5 cm
5 cm
DIN-bevestiging voor/achter
Dit toestel kan geïnstalleerd worden via een
voor- of achtermontage.
Gebruik voor installatie in de handel verkrijgbare
onderdelen.
DIN-voormontage
1 Schuif de montagebehuizing in het dash-
board.
Gebruik voor installatie in een ondiepe ruimte de
meegeleverde montagebehuizing. Als er vol-
doende ruimte is, gebruikt u de montagebehui-
zing die met het voertuig geleverd werd.
2 Zet de montagebehuizing vast door met
een schroevendraaier de metalen lipjes op
hun plaats te buigen (90°).
1
2
1 Dashboard
2 Montagebehuizing
# Controleer of het toestel stevig op zijn plaats is
gemonteerd. Het toestel functioneert wellicht niet
naar behoren als het niet goed is bevestigd.
DIN-achtermontage
1 Bepaal de juiste positie waar de gaten in
de klem en in de zijde van het toestel op een
lijn liggen.
2 Draai aan elke kant twee schroeven vast.
1
2
3
1 Zelftappende schroef (5 mm × 8 mm)
2 Bevestigingsklem
3 Dashboard of console
Het toestel verwijderen
1 Verwijder de sierlijst.
1 Sierlijst
2 Lipje met inkeping
! De sierlijst is gemakkelijker bereikbaar als u
het voorpaneel verwijdert.
! Plaats de sierlijst terug met de kant met het
lipje met de inkeping onderaan.
2 Steek de meegeleverde uittreksleutels in
de beide kanten van het toestel totdat ze op
hun plaats klikken.
3 Trek het toestel uit het dashboard.
Het voorpaneel verwijderen en terug
bevestigen
U kunt het voorpaneel verwijderen om het toe-
stel tegen diefstal te beveiligen.
Druk op de knop om het voorpaneel los te
maken, duw het naar boven en trek het naar u
toe.
Raadpleeg Het voorpaneel tegen diefstal verwij-
deren en Het voorpaneel terugzetten op bladzijde
72 voor meer informatie.
Installatie
78
Hoofdstuk
Installatie
Nl
03
Black plate (79,1)
Problemen verhelpen
Symptoom Oorzaak Actie
Het display
keert automa-
tisch terug
naar het ge-
wone display.
U hebt gedu-
rende ongeveer
30 seconden
geen handeling
uitgevoerd.
Voer de handeling
opnieuw uit.
Het bereik
voor herhaald
afspelen
wordt onver-
wachts gewij-
zigd.
Afhankelijk van
het herhaalbe-
reik kan het ge-
selecteerde be-
reik gewijzigd
worden wan-
neer u een an-
dere map of een
ander fragment
selecteert of
vooruit of ach-
teruit spoelt.
Selecteer het ge-
wenste herhaal-
bereik opnieuw.
Een onderlig-
gende map
wordt niet af-
gespeeld.
Onderliggende
mappen worden
niet afgespeeld
wanneer FLD
(map herhalen)
is geselecteerd.
Selecteer een
ander herhaalbe-
reik.
Als het dis-
play wordt ge-
wijzigd, ver-
schijnt NO
XXXX (bij-
voorbeeld NO
TITLE).
Er is geen tekst-
informatie be-
schikbaar.
Wijzig de display-
stand of speel
een ander frag-
ment of bestand
af.
Symptoom Oorzaak Actie
Het toestel
functioneert
niet correct.
Er is interfe-
rentie.
Er wordt nabij
dit toestel een
ander apparaat
(bijvoorbeeld
een draagbare
telefoon) ge-
bruikt dat elek-
tromagnetische
straling uit-
zendt.
Gebruik nabij dit
toestel geen elek-
trische apparaten
die interferentie
kunnen veroorza-
ken.
Foutmeldingen
Schrijf een foutmelding altijd nauwkeurig op en
houd die bij de hand als u contact opneemt met
uw leverancier of Pioneer-servicecentrum.
Algemeen
Melding Oorzaak Actie
AMP ERROR Het toestel
werkt niet of er
is een probleem
met de luidspre-
keraansluiting;
het beveiligings-
circuit is geacti-
veerd.
Controleer de
luidsprekeraan-
sluiting. Neem
contact op met
uw leverancier of
een erkend
Pioneer Service-
centrum als het
bericht nog wordt
weergegeven
nadat u de motor
hebt uit- en aan-
gezet.
Cd-speler
Melding Oorzaak Actie
ERROR-07,
11, 12, 17, 30
De disc is vuil. Reinig de disc.
De disc is be-
krast.
Plaats een andere
disc.
ERROR-07,
10, 11, 12,
15, 17, 30,
A0
Elektrisch of
mechanisch
probleem.
Zet het contact
uit en weer aan,
of schakel over
naar een andere
signaalbron en
dan terug naar de
cd-speler.
ERROR-15 De geplaatste
disc bevat geen
gegevens.
Plaats een andere
disc.
ERROR-23 Het cd-formaat
wordt niet on-
dersteund.
Plaats een andere
disc.
FORMAT
READ
Na het begin
van het afspelen
duurt het soms
even totdat er
geluid klinkt.
Wacht tot het be-
richt verdwijnt en
er geluid klinkt.
NO AUDIO De geplaatste
disc bevat geen
afspeelbare be-
standen.
Plaats een andere
disc.
SKIPPED De geplaatste
disc bevat be-
standen die
door digitaal
rechtenbeheer
(DRM) beveiligd
zijn.
Plaats een andere
disc.
PROTECT Alle bestanden
op de disc zijn
door digitaal
rechtenbeheer
(DRM) bevei-
ligd.
Plaats een andere
disc.
Aanwijzingen voor het gebruik
Discs en de player
Gebruik uitsluitend discs die voorzien zijn van een
van onderstaande twee logos.
Gebruik discs van 12 cm. Gebruik geen discs van 8
cm en probeer deze ook niet met een adapter af te
spelen.
Gebruik uitsluitend normale, ronde discs. Gebruik
geen discs met een andere vorm.
Plaats geen ander object dan een cd in de cd-laad-
sleuf.
Gebruik geen gebarsten, gebroken, kromme of op
andere wijze beschadigde discs omdat die de spe-
ler kunnen beschadigen.
Niet-gefinaliseerde cd-r/rw-discs kunnen niet wor-
den afgespeeld.
Raak de gegevenszijde van de disc niet aan.
Bewaar discs in het bijbehorende doosje wanneer
u ze niet gebruikt.
Plak geen labels op discs, schrijf er niet op en
breng het oppervlak niet in aanraking met chemi-
sche middelen.
Als u een cd reinigt, veegt u de disc van het mid-
den naar de buitenkant met een zachte doek
schoon.
Nederlands
Aanvullende informatie
79
Aanhangsel
Aanvullende informatie
Nl
Black plate (80,1)
Condens en vocht kunnen de werking van de spe-
ler tijdelijk negatief beïnvloeden. Laat de speler in
een warmere omgeving ongeveer een uur op tem-
peratuur komen. Veeg vochtige schijven met een
zachte doek schoon.
Sommige discs kunnen niet worden afgespeeld af-
hankelijk van het type disc, de indeling ervan, de
toepassing waarmee deze is opgenomen, de om-
geving waarin deze wordt afgespeeld, de manier
waarop deze wordt bewaard, enzovoort.
Schokken tijdens het rijden van het voertuig kun-
nen de disc laten overslaan.
Lees de voor discs geldende voorzorgsmaatrege-
len voordat u ze gebruikt.
Bij gebruik van discs met een bedrukbaar labelop-
pervlak moet u de instructies en waarschuwingen
van de discs controleren. Afhankelijk van de disc
kan laden of uitwerpen niet mogelijk zijn. Het ge-
bruik van zulke discs kan dit toestel beschadigen.
Plak geen in de handel verkrijgbare labels of an-
dere materialen op de discs.
! De discs kunnen vervormen waardoor ze onaf-
speelbaar kunnen worden.
! De labels kunnen loslaten tijdens het afspelen
en de disc blokkeren bij het uitwerpen en het
toestel beschadigen.
DualDiscs
DualDiscs zijn dubbelzijdige discs met aan de ene
kant een beschrijfbaar cd-oppervlak voor audio- op-
namen en aan de andere kant een beschrijfbaar
dvd-oppervlak voor video-opnamen.
Aangezien de cd-zijde van DualDiscs niet overeen-
komt met de algemene cd-standaard, is het wel-
licht niet mogelijk de cd-zijde op dit toestel af te
spelen.
Het regelmatig plaatsen en uitwerpen van een
DualDisc kan krassen veroorzaken op de disc wat
tot afspeelproblemen leidt. In sommige gevallen
kan een DualDisc vast komen te zitten in de cd-
laadsleuf en niet meer worden uitgeworpen. Om
problemen te voorkomen wordt aangeraden om
op dit toestel geen DualDiscs af te spelen.
Raadpleeg de informatie van de fabrikant van de
disc voor meer informatie over DualDiscs.
Compatibiliteit met
gecomprimeerde audio
WMA
Bestandsextensie: .wma
Bitsnelheid: 48 kbps tot 320 kbps (CBR), 48 kbps
tot 384 kbps (VBR)
Bemonsteringsfrequentie: 32 kHz, 44,1 kHz, 48
kHz
Windows Media Audio Professional, Lossless,
Voice/DRM Stream/Stream met video: Niet com-
patibel
MP3
Bestandsextensie: .mp3
Bitsnelheid: 8 kbps tot 320 kbps (CBR), VBR
Bemonsteringsfrequentie: 8 kHz tot 48 kHz
(32 kHz, 44,1 kHz, 48 kHz voor de beste kwaliteit)
Compatibele ID3-tag-versie: 1.0, 1.1, 2.2, 2.3, 2.4
(ID3-tag versie 2.x krijgt prioriteit boven versie 1.x.)
M3u speellijst: Niet compatibel
MP3i (MP3 interactive), mp3 PRO: Niet compati-
bel
WAV
Bestandsextensie: .wav
Quantisatiebits: 8 en 16 (LPCM), 4 (MS ADPCM)
Bemonsteringsfrequentie: 16 kHz tot 48 kHz
(LPCM), 22,05 kHz en 44,1 kHz (MS ADPCM)
Bijkomende informatie
Alleen de eerste 32 tekens van de bestandsnaam
(inclusief de extensie) of mapnaam worden weer-
gegeven.
Russische tekst kan alleen op dit toestel worden
weergegeven als die met een van de volgende te-
kensets is gecodeerd:
! Unicode (UTF-8, UTF-16)
! Andere tekensets dan Unicode die in een
Windows-omgeving worden gebruikt en op
Russisch zijn ingesteld bij de taalinstellingen
Een juiste werking van dit toestel is afhankelijk
van de toepassing waarmee de WMA-bestanden
zijn gecodeerd.
Disc
Mappenhiërarchie: maximaal acht niveaus diep
(Voor praktisch gebruik kunt u beter niet meer dan
twee niveaus gebruiken.)
Afspeelbare mappen: maximaal 99
Afspeelbare bestanden: maximaal 999
Bestandssysteem: ISO 9660 Level 1 en 2, Romeo,
Joliet
Afspelen van multisessie-discs: Compatibel
Packet write data transfer: Niet compatibel
Bij het afspelen van gecomprimeerde audiodiscs
wordt altijd een korte pauze ingelast tussen de
fragmenten. Dit gebeurt ongeacht de duur tussen
de fragmenten op de originele opname.
LET OP
Laat discs niet achter op plaatsen waar de tem-
peratuur hoog kan oplopen.
Volgorde van audiobestanden
De gebruiker kan met dit toestel geen mapnum-
mers toewijzen of de afspeelvolgorde wijzigen.
Voorbeeld van een boomstructuur
1
2
3
4
5
6
01
02
03
04
05
Niveau 1 Niveau 2 Niveau 3 Niveau 4
: Map
: Gecomprimeerd
audiobestand
01 tot 05: Mapnum-
mer
1 tot 6: Afspeel-
volgorde
Disc
De mapvolgorde en andere instellingen zijn af-
hankelijk van de software die voor het coderen
en schrijven is gebruikt.
Lijst van Russische tekens
S: T S: T S: T S: T S: T
: А : Б : В : Г : Д
: Е, Ё : Ж : З : И, Й : К
: Л : М : Н : О : П
Aanvullende informatie
80
Aanhangsel
Aanvullende informatie
Nl
Black plate (81,1)
S: T S: T S: T S: T S: T
: Р : С : Т : У : Ф
: Х : Ц : Ч
: Ш,
Щ
: Ъ
: Ы : Ь : Э : Ю : Я
S: Scherm T: Teken
Copyright en handelsmerken
iTunes
Apple en iTunes zijn handelsmerken van
Apple Inc., geregistreerd in de V.S. en andere
landen.
MP3
Dit product is uitsluitend bedoeld voor niet-com-
mercieel privégebruik. Het mag niet in een com-
merciële omgeving worden gebruikt voor
realtime-uitzendingen (over land, via satelliet,
kabel en/of andere media), voor uitzendingen/
streaming via internet, intranet en/of andere net-
werken, of in andere elektronische distributie-
systemen zoals betaalradio of audio-op-
aanvraagtoepassingen. Hiervoor is een aparte li-
centie nodig. Kijk voor meer informatie op
http://www.mp3licensing.com.
WMA
Windows Media is een gedeponeerd handels-
merk of een handelsmerk van Microsoft
Corporation in de Verenigde Staten en/of in an-
dere landen.
Dit product bevat technologie die het eigendom
is van Microsoft Corporation en die niet gebruikt
of gedistribueerd mag worden zonder toestem-
ming van Microsoft Licensing, Inc.
Technische gegevens
Algemeen
Spanningsbron ................ 14,4 V gelijkstroom (10,8 tot
15,1 V toelaatbaar)
Aarding ........................... Negatief
Maximaal stroomverbruik
................................... 10,0 A
Afmetingen (B × H × D):
DIN
Chassis .............. 178mm × 50mm ×
165 mm
Voorkant ............ 188mm × 58mm ×
16 mm
D
Chassis .............. 178mm × 50mm ×
165 mm
Voorkant ............ 170mm × 46mm ×
16 mm
Gewicht ........................... 1 kg
Audio
Maximaal uitgangsvermogen
................................... 50 W × 4
70 W × 1/2 W (voor de sub-
woofer)
Doorlopend uitgangsvermogen
................................... 22W × 4 (50Hz tot 15000Hz,
5% THD, 4 W belast ing, beide
kanalen)
Belastingsimpedantie ...... 4 W (4 W tot 8 W toegestaan)
Preout maximaal uitgangsniveau
................................... 2,0V
Contouren loudness ......... +10dB (100 Hz), +6,5 dB
(10 kHz) (volume: 30 dB)
Equalizer (grafische equalizer met vijf banden):
Frequentie ................ 80Hz/250 Hz/800 Hz/
2,5 kHz/8 kHz
Bereik equalizer ........ ±12 dB (in stappen van 2
dB)
Subwoofer (mono):
Frequentie ................ 50Hz/63 Hz/80 Hz/100 Hz/
125 Hz/160 Hz/200 Hz
Helling ...................... 6 dB/oct, 12 dB/oct
Gain ......................... +6dB tot 24 dB
Fase .......................... Normaal/tegengesteld
Cd-speler
Systeem ........................... Compact Disc Audio
Bruikbare discs ................ Compact Discs
Signaal-tot-ruisverhouding
................................... 94dB (1kHz) (IEC-A-netwerk)
Aantal kanalen ................. 2 (stereo)
MP3-decoderingsformaat
................................... MPEG-1 & 2 Audio Layer 3
WMA-decoderingsformaat
................................... Versie 7, 7.1, 8, 9, 10, 11, 12
(2 kan. audio)
(Windows Media Player)
WAV-signaalformaat ........ Lineaire PCM & MS ADPCM
(niet gecomprimeerd)
FM-tuner
Frequentiebereik .............. 87,5 MHz tot 108,0 MHz
Bruikbare gevoeligheid .... 9dBf (0,8 µV/75 W, mono, S/R:
30 dB)
Signaal-tot-ruisverhouding
................................... 72dB (IEC-A-netwerk)
MW-tuner
Frequentiebereik .............. 531 kHz tot 1 602 kHz
Bruikbare gevoeligheid .... 25µV (S/R: 20 dB)
Signaal-tot-ruisverhouding
................................... 62dB (IEC-A-netwerk)
LW-tuner
Frequentiebereik .............. 153 kHz tot 281kHz
Bruikbare gevoeligheid .... 28µV (S/R: 20 dB)
Signaal-tot-ruisverhouding
................................... 62dB (IEC-A-netwerk)
Opmerking
Technische gegevens en ontwerp kunnen zonder
voorafgaande kennisgeving worden gewijzigd.
Nederlands
Aanvullende informatie
81
Aanhangsel
Aanvullende informatie
Nl
Black plate (82,1)
Благодарим Вас
за покупку этого изделия
компании PIONEER.
Для обеспечения правильности эксплуата-
ции внимательно прочитайте данное руко-
водство перед началом использования
изделия. Особенно важно, чтобы Вы прочли
и соблюдали инструкции, помеченные в дан-
ном руководстве заголовками ПРЕДУПРЕ-
ЖДЕНИЕ и ВНИМАНИЕ.
Держите данное
руководство под рукой для обращения к
нему в будущем.
Если вы желаете утилизировать данное
изделие, не выбрасывайте его вместе с
обычным бытовым мусором. Существует
отдельная система сбора использованных
электронных изделий в соответствии с за-
конодательством, которая предполагает
соответствующее обращение, возврат и
переработку.
Частные лица в странах Евросоюза, Швей-
царии и Норвегии могут бесплатно возвра-
щать использованные электронные изделия
в специализированные пункты приема или в
магазин (при покупке аналогичного нового
устройства).
Если Ваша страна не указана в приведенном
выше перечне, обращайтесь в органы мест-
ного управления за инструкциями по пра-
вильной утилизации продукта.
Тем самым Вы обеспечите утилизацию Ва-
шего изделия с соблюдением обязательных
процедур по обработке, утилизации и вто-
ричной переработке и, таким образом, пред-
отвратите потенциальное негативное
воздействие на окружающую среду и здоро-
вье людей.
Дату изготовления оборудования можно
определить по серийному номеру, который
содержит информацию о месяце и годе про-
изводства.
Сведения об этом устройстве
Частоты тюнера в этом устройстве распре-
делены для использования в Западной
Европе, Азии, на Ближнем Востоке, в Афри-
ке и Океании. При использовании в других
регионах качество приема может быть пло-
хим. Функция RDS (радиовещательная си-
стема передачи информации) доступна
только в регионах, где транслируются сигна-
лы RDS для FM-станций.
ВНИМАНИЕ
Данное изделие является лазерным изде-
лием класса 1 согласно классификации по
Безопасности лазерных изделий, IEC
60825-1:2007.
ЛАЗЕРНЫЙ ПРОДУКТ КЛАСС 1
ВНИМАНИЕ
! Не допускайте попадания жидкости на ус-
тройство. Это может повлечь поражение
электрическим током. Кроме того, попада-
ние жидкости в устройство может стать
причиной его выхода из строя, перегрева
и появления дыма.
! Pioneer CarStereo-Pass предназначен для
использования только в Германии.
! Всегда сохраняйте уровень громкости до-
статочно низким, чтобы были слышны
звуки извне.
! Не допускайте воздействия влажности на
изделие.
! При отключении или разряде аккумуля-
торной батареи память предварительных
настроек будет стерта.
Примечание
Выполненные настройки вступают в силу,
даже если выйти из меню без подтвержде-
ния настройки.
В случае возникновения
неполадок
При неполадках в работе этого изделия свя-
житесь с торговым представителем компа-
нии-производителя или с ближайшим
сервисным пунктом Pioneer.
Перед началом эксплуатации
82
Раздел
Перед началом эксплуатации
Ru
01
Black plate (83,1)
Основное устройство
b c
5
8
1 2 3 4 6
a9d7
Элемент Элемент
1 h (извлечение) 8 BAND
2 SRC/OFF 9
(назад)/DIM-
MER (регулятор
освещенности)
3
MULTI-CONTROL
(M.C.)
a c/d
4
(список) b С 1/ по 6/
5 DISP c
Вход AUX (сте-
реоразъем
3,5 мм)
6
Щель для за-
грузки диска
d
Кнопка снятия
панели
7
(эквалай-
зер)
Индикация на дисплее
21 3 75
9
4 6 8
a
Индика-
тор
Состояние
1
(список) Работает функция списка.
2
Сектор до-
полнитель-
ной ин-
формации
Отображается дополни-
тельная информация.
3
TA (дорож-
ные свод-
ки)
Включена функция приема
дорожных сводок.
4
TP (иден-
тификатор
дорожных
программ)
Тюнер настроен на TP-
станцию.
5
(sound ret-
riever, тех-
нология
преобраз-
ования
звука)
Включен режим Sound Ret-
riever (технология преоб-
разования звука).
6 LOC
Включена настройка с
местным поиском.
7
(по-
втор)
Включён режим повторного
воспроизведения дорожки
или папки.
8
(в про-
извольной
последова-
тельности)
Включён режим воспроиз-
ведения в произвольной по-
следовательности.
Индика-
тор
Состояние
9
Сектор ос-
новной ин-
формации
! Тюнер: диапазон и ча-
стота
! RDS: название програм-
мы, PTY-информация и
прочая текстовая ин-
формация
! Проигрыватель компакт-
дисков: время, прошед-
шее с начала воспроиз-
ведения, и текстовая
информация
a
Отображается при наличии
нижнего уровня папки или
меню.
Установочное меню
При повороте ключа зажигания в положение
ON после установки устройства на дисплее
появляется установочное меню.
Оно позволяет выполнить следующие на-
стройки.
1 После установки устройства поверни-
те ключ зажигания в положение ON.
Появится надпись SET UP.
2 Поверните M.C. для выбора YES.
# Если в течение 30 секунд не выполняется ни-
каких операций, установочное меню не будет вы-
водиться.
# Если вы хотите выполнить настройку позже,
поверните M.C., чтобы выбрать NO. Нажмите
для выбора.
В случае выбора NO настройка в установочном
меню невозможна.
3 Нажмите M.C. для выбора.
4 Для настройки выполните следующие
процедуры.
Для перехода к следующему пункту меню
необходимо подтвердить выбор.
LANGUAGE (выбор языка)
Данное устройство может отображать тексто-
вую информацию из сжатых аудиофайлов, в
том числе информацию на английском и рус-
ском языках.
! При несовместимости настроек встроенно-
го и выбранного языка возможны искаже-
ния при выводе текстовых сообщений.
! Некоторые символы могут отображаться
неправильно.
1 Поворачивайте M.C. для выбора настрой-
ки.
ENG (английский)РУС (русский)
2 Нажмите M.C., чтобы подтвердить выбор.
CLOCK SET (установка часов)
1 Поворачивайте M.C., чтобы установить
часы.
2 Нажимайте M.C., чтобы выбрать установку
минут.
3 Поворачивайте M.C., чтобы установить ми-
нуты.
4 Нажмите M.C., чтобы подтвердить выбор.
FM STEP (шаг настройки в FM-диапазоне)
Обычно шаг настройки в FM-диапазоне, ис-
пользуемый при настройке с поиском, соста-
вляет 50 кГц. При включении функции AF или
TA шаг настройки автоматически меняется на
100 кГц. При включенной функции AF предпо-
чтительно установить шаг настройки 50 кГц.
! Во время ручной настройки шаг настройки
составляет 50 кГц.
1 Поверните M.C., чтобы выбрать шаг на-
стройки в FM-диапазоне.
50 (50 кГц)100 (100 кГц)
2 Нажмите M.C., чтобы подтвердить выбор.
Появится надпись QUIT.
Русский
Управление данным устройством
83
Раздел
Управление данным устройством
Ru
02
Black plate (84,1)
5 Чтобы закончить настройку, поверни-
те M.C. и выберите YES.
# Если понадобится вновь изменить настройку,
поверните M.C. и выберите NO. Нажмите для вы-
бора.
6 Нажмите M.C. для выбора.
Примечания
! Настроить параметры меню можно в
меню системы. Более подробную инфор-
мацию см. в разделе
Меню системы
на
стр. 88.
! Вы можете отменить настройку парамет-
ра, нажав кнопку SRC/OFF.
Основные операции
Важно
! Соблюдайте осторожность при снятии и
установке передней панели.
! Оберегайте переднюю панель от сильных
ударов.
! Предохраняйте переднюю панель от воз-
действия прямого солнечного света и вы-
соких температур.
! Прежде чем снять переднюю панель, обя-
зательно отключите от нее все кабели и
устройства, чтобы не повредить устрой-
ство и внутреннюю отделку салона.
Снятие передней панели в целях защиты от
кражи
1 Чтобы отсоединить переднюю панель, на-
жмите на кнопку отсоединения панели.
2 Нажмите на панель по направлению вверх
(M) и потяните на себя (N).
3 Всегда храните снятую переднюю панель в
защитном футляре.
Установка передней панели
1 Зафиксируйте левый край панели на ус-
тройстве.
Убедитесь, что язычки с левой стороны ос-
новного устройства вошли в пазы на пере-
дней панели.
2 Нажмите на правый край передней панели
и зафиксируйте ее.
Если прикрепить переднюю панель к ос-
новному устройству не удается, убедитесь,
что действия производятся в правильном
порядке. В случае приложения излишнего
усилия передняя панель или основное ус-
тройство могут быть повреждены.
Включение устройства
1 Нажмите кнопку SRC/OFF, чтобы включить
устройство.
Выключение устройства
1 Нажмите и удерживайте кнопку SRC/OFF,
пока устройство не выключится.
Выбор источника сигнала
1 Нажимайте кнопку SRC/OFF для выбора из
следующих функций:
TUNER (тюнер)CD (проигрыватель ком-
пакт-дисков)AUX (вспомогательное ус-
тройство (AUX))
Регулировка громкости
1 Для регулировки громкости поворачивайте
M.C.
ВНИМАНИЕ
В целях безопасности остановите автомо-
биль, прежде чем снять переднюю панель.
Примечание
Когда голубой/белый провод этого устрой-
ства подключен к реле панели управления
автомобильной антенной, антенна на авто-
мобиле выдвигается при включении источни-
ка сигнала этого устройства. Чтобы втянуть
антенну, выключите источник сигнала.
Часто используемые
элементы меню
Возврат к предыдущему дисплею
Возврат к предыдущему списку (к папке на
один уровень выше)
1 Нажмите кнопку
/DIMMER.
Возврат в исходный режим
Выход из главного меню
1 Нажмите BAND.
Возврат в исходный режим из списка
1 Нажмите BAND.
Тюнер
Основные операции
Выбор диапазона
1 Нажимайте кнопку BAND, пока на дисплее
не появится нужный диапазон (FM1, FM2,
FM3 для FM или MW/LW).
Переключение станций предварительной на-
стройки
1 Нажмите кнопку c или d.
! Выберите PCH (станции предварительной
настройки) в меню SEEK, чтобы воспользо-
ваться этой функцией. Подробнее о на-
стройках см. в разделе
SEEK (настройка
левой и правой кнопок)
на стр. 86.
Ручная настройка (пошаговая)
1 Нажмите кнопку c или d.
! Выберите MAN (ручная настройка) в меню
SEEK, чтобы воспользоваться этой функ-
цией. Подробнее о настройках см. в разде-
ле
SEEK (настройка левой и правой кнопок)
на стр. 86.
Поиск
1 Нажмите и удерживайте кнопку c или d, а
затем отпустите.
Вы можете отменить настройку с поиском
кратким нажатием c или d.
При нажатии и удерживании кнопки c или
d можно пропускать радиостанции. На-
стройка с поиском начнется сразу после от-
пускания кнопки c или d.
Примечание
Можно включить или выключить функцию AF
(поиск альтернативных частот) данного ус-
тройства. Для обычной настройки функция
AF должна быть выключена (смотрите в
AF
(поиск альтернативных частот)
на стр. 85).
Управление данным устройством
84
Раздел
Управление данным устройством
Ru
02
Black plate (85,1)
Сохранение и вызов из памяти
радиостанций для каждого
диапазона
Использование кнопок
предварительной настройки
1 Чтобы сохранить в памяти нужную ра-
диостанцию, нажмите одну из кнопок
предварительной настройки (с 1/
по 6/
) и удерживайте ее, пока номер предва-
рительной настройки не прекратит ми-
гать.
2 Для выбора нужной радиостанции на-
жмите одну из кнопок предварительной
настройки (с 1/
по 6/ ).
Переключение дисплея
Выбор текстовой информации
1 Нажимайте DISP для выбора из следующих
функций:
! FREQUENCY (служебное название про-
граммы или частота)
! BRDCST INFO (служебное название про-
граммы/информация PTY)
! CLOCK (название источника сигнала и
часы)
Примечания
! Если служебное название программы в
поле FREQUENCY отсутствует, вместо
него отображается канал. Если служеб-
ное название программы обнаружено,
оно будет отображаться.
! Текстовая информация BRDCST INFO
будет изменяться автоматически.
! Текстовая информация может меняться в
зависимости от диапазона.
! Возможность внесения изменений в тек-
стовую информацию зависит от региона.
Использование функций PTY
Можно настроиться на радиостанцию с по-
мощью информации PTY (типа программы).
Поиск станции RDS с помощью информации
PTY
Можно выполнять поиск общих радиовеща-
тельных программ, например, тех, что перечи-
слены в следующем разделе. См. стр. 85.
1 Нажмите
(список).
2 Кнопкой M.C. выберите тип программы.
NEWS/INFOPOPULARCLASSICSOT-
HERS
3 Нажмите M.C., чтобы начать поиск.
Устройство начинает поиск радиостанций,
передающих данный тип программ. При
обнаружении радиостанции на дисплее
будет показано название данной програм-
мы.
! Для отмены поиска нажмите M.C. еще
раз.
! Программы некоторых радиостанций
могут отличаться от программ, указан-
ных в передаваемом коде PTY.
! Если ни одна из станций не передает
программы нужного типа, то на дисплее
в течение примерно двух секунд будет
показано NOT FOUND, и затем тюнер
перейдет в режим приема станции, ско-
торой был начат поиск.
Список PTY
NEWS/INFO (новости и информация)
NEWS (новости), AFFAIRS (текущая информа-
ция), INFO (информация), SPORT (спорт),
WEATHER (погода), FINANCE (финансы)
POPULAR (поп-музыка)
POP MUS (поп-музыка), ROCK MUS (рок-музы-
ка), EASY MUS (легкая музыка), OTH MUS
(прочие музыкальные жанры), JAZZ (джаз),
COUNTRY (кантри), NAT MUS (национальная
музыка), OLDIES (золотая коллекция), FOLK
MUS (народная музыка)
CLASSICS (классика)
L. CLASS (легкая классическая музыка), CLAS-
SIC (классическая музыка)
OTHERS (прочее)
EDUCATE (образовательные программы),
DRAMA (постановки), CULTURE (культура),
SCIENCE (наука), VARIED (разное), CHILDREN
(детские программы), SOCIAL (социальные во-
просы), RELIGION (религиозные программы),
PHONE IN (ток-шоу), TOURING (путешествия),
LEISURE (отдых), DOCUMENT (документаль-
ные программы)
Настройка функций
1 Нажмите M.C., чтобы открыть главное
меню.
2 Поворачивайте M.C. для прокрутки
пунктов меню; нажмите, чтобы выбрать
FUNCTION.
3 Для выбора функции поворачивайте
M.C.
Следующие выбранные функции можно на-
страивать.
# В диапазонах MW/LW можно выбрать только
BSM, LOCAL и SEEK.
BSM (запоминание лучших станций)
Функция BSM (запоминание лучших станций)
позволяет автоматически сохранять в памяти
устройства шесть станций с самым мощным
сигналом в порядке убывания его мощности.
1 Нажмите M.C., чтобы включить функцию
BSM.
Для отмены режима нажмите M.C. еще раз.
REGION (региональный)
При использовании функции AF функция ре-
гиональных программ ограничивает выбор
станциями, транслирующими региональные
программы.
1 Нажмите M.C., чтобы включить или выклю-
чить функцию региональных программ.
LOCAL (настройка с местным поиском)
Настройка с местным поиском позволяет Вам
настраиваться только на радиостанции с до-
статочно мощными сигналами для качествен-
ного приема.
1 Нажмите M.C. для выбора нужной настрой-
ки.
FM: OFFLV1LV2LV3LV 4
MW/LW: OFFLV1LV2
Настройка самого высокого уровня позво-
ляет осуществлять прием только станций с
самым сильным сигналом, а уменьшение
уровня настройки позволяет принимать
станции с более слабым сигналом.
TA (режим ожидания дорожных сводок)
1 Нажмите M.C., чтобы включить или выклю-
чить режим ожидания дорожных сводок.
AF (поиск альтернативных частот)
1 Нажмите M.C., чтобы включить или выклю-
чить функцию AF.
NEWS (прерывание для передачи новостей)
Русский
Управление данным устройством
85
Раздел
Управление данным устройством
Ru
02
Black plate (86,1)
1 Нажмите M.C., чтобы включить или выклю-
чить функцию НОВОСТИ.
SEEK (настройка левой и правой кнопок)
Правой и левой кнопкам на устройстве можно
назначить определенную функцию.
Выберите MAN (ручная настройка) для ручной
настройки или PCH (предустановленный
канал) для переключения между заранее на-
строенными каналами.
1 Нажмите кнопку M.C., чтобы выбрать MAN
или PCH.
CD/CD-R/CD-RW
Основные операции
Воспроизведение CD/CD-R/CD-RW
1 Вставьте диск в щель для загрузки марки-
рованной стороной вверх.
Извлечение диска CD/CD-R/CD-RW
1 Нажмите h.
Выбор папки
1 Нажмите кнопку 1/
или 2/ .
Выбор дорожки
1 Нажмите кнопку c или d.
Ускоренная перемотка вперед или назад
1 Нажмите и удерживайте кнопку c или d.
! При воспроизведении сжатых аудиофай-
лов звук не воспроизводится, если включе-
на ускоренная перемотка вперед или
назад.
Возврат к корневой папке
1 Нажмите и удерживайте BAND.
Переключение между сжатыми аудиофайлами
и диском CD-DA
1 Нажмите BAND.
Переключение дисплея
Выбор текстовой информации
1 Нажимайте DISP для выбора из следующих
функций:
CD-DA
! ELAPSED TIME (номер дорожки и время
воспроизведения)
! CLOCK (название источника сигнала и
часы)
! SPEANA (анализатор спектра)
CD-TEXT
! TRACK INFO (название дорожки/испол-
нитель/название диска)
! ELAPSED TIME (номер дорожки и время
воспроизведения)
! CLOCK (название источника сигнала и
часы)
! SPEANA (анализатор спектра)
MP3/WMA/WAV
! TRACK INFO (название дорожки/имя ис-
полнителя/название альбома)
! FILE INFO (название папки/название
файла)
! ELAPSED TIME (номер дорожки и время
воспроизведения)
! CLOCK (название источника сигнала и
часы)
! SPEANA (анализатор спектра)
Примечания
! Текстовая информация TRACK INFO и
FILE INFO будет изменяться автоматиче-
ски.
! В зависимости от версии iTunes, исполь-
зуемой для записи файлов МР3 на диск,
или от типа медиафайла текстовая ин-
формация несовместимого формата, за-
писанная в аудиофайле, может
отображаться некорректно.
! Возможность внесения изменений в тек-
стовую информацию зависит от типа но-
сителя.
Выбор и воспроизведение
фалов/дорожек из списка
1 Нажмите кнопку , чтобы отобразить
список названий файлов/дорожек.
2 С помощью M.C. выберите нужное
имя файла (или папки).
Выбор файла или папки
1 Поворачивайте M.C.
Воспроизведение
1 Выберите файл или дорожку и нажмите M.
C.
Просмотр списка названий файлов (папок) в
выбранной папке
1 Выберите папку и нажмите M.C.
Воспроизведение композиции из выбранной
папки
1 Выберите папку, затем нажмите и удержи-
вайте M.C.
Функции с использованием
специальных кнопок
Выбор диапазона повторного воспроизведе-
ния
1 Нажимайте кнопку 6/
для выбора из сле-
дующих функций:
! ALL Повторное воспроизведение всех
дорожек
! ONE Повтор текущей дорожки
! FLD Повтор текущей папки
Воспроизведение дорожек в произвольной по-
следовательности
1 Нажмите кнопку 5/
, чтобы включить или
выключить функцию воспроизведения в
произвольной последовательности.
Данная функция позволяет воспроизводить
дорожки в произвольной последовательно-
сти в пределах выбранного диапазона по-
вторного воспроизведения.
! Для переключения на следующую дорожку
во время воспроизведения в произвольной
последовательности нажмите кнопку d.
При нажатии на кнопку c воспроизведение
текущей дорожки начинается с начала.
Приостановка воспроизведения
1 Нажмите кнопку 4/PAUSE, чтобы включить
паузу или возобновить воспроизведение.
Улучшение качества звука сжатых аудиофай-
лов и восстановление полноты звучания (тех-
нология преобразования звука)
1 Нажимайте кнопку 3/S.Rtrv для выбора из
следующих функций:
12OFF (выкл)
Настройка 1 эффективна для файлов с
низкой степенью сжатия, а настройка 2
для файлов с высокой степенью сжатия.
Управление данным устройством
86
Раздел
Управление данным устройством
Ru
02
Black plate (87,1)
Настройка функций
1 Нажмите M.C., чтобы открыть главное
меню.
2 Поворачивайте M.C. для прокрутки
пунктов меню; нажмите, чтобы выбрать
FUNCTION.
Выбранные функции, которые можно на-
страивать, перечислены ниже.
S.RTRV (sound retriever, технология преобраз-
ования звука)
Автоматически улучшает качество звука сжа-
тых аудиофайлов и восстанавливает полноту
звучания.
1 Нажмите M.C. для выбора нужной настрой-
ки.
Подробную информацию см. в
Улучшение
качества звука сжатых аудиофайлов и вос-
становление полноты звучания (технология
преобразования звука)
на стр. 86.
Регулировки параметров звука
1 Нажмите M.C., чтобы открыть главное
меню.
2 Поворачивайте M.C. для прокрутки
пунктов меню; нажмите, чтобы выбрать
AUDIO.
3 Для выбора аудиофункции поворачи-
вайте M.C.
Следующие выбранные аудиофункции
можно настраивать.
! Функция FADER недоступна, если в режи-
ме SP-P/O MODE выбрано SUB.W/SUB.W.
Подробнее см. в разделе
SP-P/O MODE
(настройка выхода заднего канала и пред-
варительного усилителя)
на стр. 89.
! Функции SUB.W, SUB.W CTRL и
HPF SETTING недоступны, если в режиме
SP-P/O MODE выбрано REAR/REAR. Под-
робнее см. в разделе
SP-P/O MODE (на-
стройка выхода заднего канала и
предварительного усилителя)
на стр. 89.
! Функции SUB.W CTRL и HPF SETTING недо-
ступны, если в режиме OFF выбрано
SUB.W. Подробнее см. в разделе
SUB.W
(включение/выключение сабвуфера)
на
стр. 87.
FADER (регулировка баланса)
1 Для отображения установочного меню на-
жмите M.C.
2 Нажмите M.C., чтобы отрегулировать ба-
ланс передних и задних громкоговорите-
лей.
BALANCE (регулировка баланса)
1 Для отображения установочного меню на-
жмите M.C.
2 Поворачивайте M.C., чтобы отрегулировать
баланс левого/правого громкоговорителей.
EQ SETTING (вызов настроек эквалайзера)
1 Для отображения установочного меню на-
жмите M.C.
2 Нажмите кнопку M.C., чтобы выбрать эква-
лайзер.
POWERFULNATURALVOCALCU-
STOM1CUSTOM2FLATSUPER BASS
Полосу и уровень эквалайзера можно отре-
гулировать, если выбрано CUSTOM1 или
CUSTOM2.
При выборе CUSTOM1 или CUSTOM2 вы-
полните действия, описанные ниже. При
выборе других настроек нажмите M.C.,
чтобы вернуться к предыдущему дисплею.
! CUSTOM1 можно настраивать отдельно
для каждого источника сигнала.
! CUSTOM2 - это общая настройка, ис-
пользуемая для всех источников сигна-
ла.
3 Для отображения установочного меню на-
жмите M.C.
4 Нажимайте M.C. для выбора из следующих
функций:
Полоса эквалайзераУровень эквалайзе-
ра
5 Поворачивайте M.C. для выбора настрой-
ки.
Полоса эквалайзера: 80HZ250HZ
800HZ2.5KHZ8KHZ
Уровень эквалайзера: от +6 до 6
! Кроме того, можно выбрать эквалайзер, на-
жимая кнопку
.
LOUDNESS (тонкомпенсация)
Тонкомпенсация компенсирует недостаточное
звуковое давление в нижнем и верхнем диапа-
зонах частот на низкой громкости.
1 Нажмите M.C. для выбора нужной настрой-
ки.
OFF (выкл)LOW (низкий)MID (средний)
HI (высокий)
SUB.W (включение/выключение сабвуфера)
Это устройство имеет выход канала сабвуфе-
ра, который можно включать и выключать.
1 Нажмите M.C. для выбора нужной настрой-
ки.
NOR (нормальная фаза)REV (обратная
фаза)OFF (сабвуфер выключен)
SUB.W CTRL (настройка сабвуфер)
На выходе сабвуфера будут воспроизводиться
только те частоты, которые ниже указанных ча-
стот среза.
1 Для отображения установочного меню на-
жмите M.C.
2 Нажимайте M.C. для выбора из следующих
функций:
Частота срезаУровень выходного сигна-
лаКрутизна характеристики
Изменяемые значения будут мигать.
3 Поворачивайте M.C. для выбора настрой-
ки.
Частота среза: 50HZ63HZ80HZ100HZ
125HZ160HZ200HZ
Уровень выходного сигнала: от 24 до +6
Крутизна характеристики: 6 12
BASS BOOST (усиление нижних звуковых ча-
стот)
1 Для отображения установочного меню на-
жмите M.C.
2 Поворачивайте M.C. для выбора нужного
уровня.
При увеличении или уменьшении уровня
отображаются надписи с 0 до +6.
HPF SETTING (настройка фильтра верхних ча-
стот)
Русский
Управление данным устройством
87
Раздел
Управление данным устройством
Ru
02
Black plate (88,1)
Если Вы не хотите, чтобы низкочастотные
звуки из диапазона частот выхода канала саб-
вуфера воспроизводились из передних или за-
дних громкоговорителей, включите HPF
(фильтр верхних частот). В этом случае из пе-
редних или задних громкоговорителей будут
воспроизводиться только звуки с частотой
выше заданной.
1 Для отображения установочного меню на-
жмите M.C.
2 Нажимайте M.C. для выбора из следующих
функций:
Частота срезаКрутизна характеристики
3 Поворачивайте M.C. для выбора настрой-
ки.
Частота среза: OFF50HZ63HZ80HZ
100HZ125HZ160HZ200HZ
Крутизна характеристики: 6 12
SLA (регулировка уровня входного сигнала)
SLA (функция настройки уровня входного сиг-
нала) позволяет регулировать уровень громко-
сти каждого источника сигнала, чтобы
предотвратить резкие изменения громкости
при переключении источников сигнала.
! Настройки основываются на уровне гром-
кости FM-тюнера, который остается неиз-
менным.
! Регулировку уровня громкости в диапазоне
MW/LW также можно производить с по-
мощью данной функции.
! При выборе FM-тюнера в качестве источ-
ника сигнала функция SLA недоступна.
1 Для отображения установочного меню на-
жмите M.C.
2 Поворачивая M.C., отрегулируйте уровень
громкости источника сигнала.
Диапазон настройки: от +4 до 4
Меню системы
Важно
PW SAVE (режим энергосбережения) отклю-
чается при отсоединении аккумуляторной
батареи автомобиля; при подсоединении ба-
тареи его потребуется включить снова. При
выключенном режиме PW SAVE (режим
энергосбережения) возможно, что, в зависи-
мости от метода подключения, устройство
будет потреблять энергию аккумулятора,
если зажигание автомобиля не имеет поло-
жения АСС.
1 Нажмите M.C., чтобы открыть главное
меню.
2 Поворачивайте M.C. для прокрутки
пунктов меню; нажмите, чтобы выбрать
SYSTEM.
3 Для выбора функции меню системы
поворачивайте M.C.
Следующие выбранные функции меню си-
стемы можно настраивать.
LANGUAGE (выбор языка)
Данное устройство может отображать тексто-
вую информацию из сжатых аудиофайлов, в
том числе информацию на английском и рус-
ском языках.
! При несовместимости настроек встроенно-
го и выбранного языка возможны искаже-
ния при выводе текстовых сообщений.
! Некоторые символы могут отображаться
неправильно.
1 Поворачивайте M.C. для выбора настрой-
ки.
ENG (английский)РУС (русский)
CLOCK SET (установка часов)
1 Для отображения установочного меню на-
жмите M.C.
2 Нажимайте M.C., чтобы выбрать сегмент
дисплея часов, который нужно установить.
ЧасыМинуты
3 Поворачивайте M.C., чтобы отрегулировать
время.
12H/24H (формат отображения времени)
1 Нажмите M.C. для выбора нужной настрой-
ки.
12H (12-часовой)24H (24-часовой)
AUTO PI (автоматический поиск по идентифи-
катору программы)
Устройство может автоматически искать дру-
гую станцию с такой же программой даже во
время вызова предварительной настройки.
1 Нажмите M.C., чтобы включить или выклю-
чить автоматический поиск по идентифика-
тору программы.
AUX (вспомогательный вход)
Активируйте эту настройку при подключении к
данному устройству вспомогательного устрой-
ства.
1 Нажмите M.C., чтобы включить или выклю-
чить функцию AUX.
MUTE MODE (режим приглушения звука)
Звук/уровень звукового сигнала данной систе-
мы автоматически понижается при получении
сигнала от оборудования с функцией приглу-
шения звука.
1 Для отображения установочного меню на-
жмите M.C.
2 Поворачивайте M.C. для выбора настрой-
ки.
Можно выбрать любую настройку из сле-
дующего списка:
! MUTE приглушение звука
! 20dB ATT ослабление уровня сигнала
(20dB ATT имеет более сильный эф-
фект, чем 10dB ATT)
! 10dB ATT ослабление уровня сигнала
PW SAVE (энергосбережение)
Включение этой функции позволяет снизить
потребляемую мощность аккумуляторной ба-
тареи.
! При включении этой функции единствен-
ной возможной операцией является вклю-
чение источника сигнала.
1 Нажмите M.C., чтобы включить или выклю-
чить функцию энергосбережения.
Настройка регулятора
освещенности
Можно настроить яркость и подсветку.
1 Нажмите M.C., чтобы открыть главное
меню.
2 Поверните M.C., чтобы отобразить
ILLUMI, затем нажмите.
3 Нажмите M.C. для выбора нужной на-
стройки.
OFF (выкл)ON (вкл)
Управление данным устройством
88
Раздел
Управление данным устройством
Ru
02
Black plate (89,1)
! Вы также можете выбрать другую на-
стройку регулятора освещенности, удер-
живая нажатой кнопку
/DIMMER.
Стартовое меню
1 Нажмите и удерживайте кнопку SRC/
OFF, пока устройство не выключится.
2 Нажмите кнопку SRC/OFF и удерживай-
те ее, пока не откроется стартовое меню.
3 Поворачивайте M.C. для прокрутки
пунктов меню; нажмите, чтобы выбрать
INITIAL.
4 Для выбора функции меню системы
поворачивайте M.C.
Следующие выбранные функции стартового
меню можно настраивать.
FM STEP (шаг настройки в FM-диапазоне)
Обычно шаг настройки в FM-диапазоне, ис-
пользуемый при настройке с поиском, соста-
вляет 50 кГц. При включении функции AF или
TA шаг настройки автоматически меняется на
100 кГц. При включенной функции AF предпо-
чтительно установить шаг настройки 50 кГц.
! Во время ручной настройки шаг настройки
составляет 50 кГц.
1 Нажмите M.C., чтобы выбрать шаг настрой-
ки в FM-диапазоне.
50 (50 кГц)100 (100 кГц)
SP-P/O MODE (настройка выхода заднего ка-
нала и предварительного усилителя)
Выход на провода заднего громкоговорителя и
выход заднего канала RCA можно использо-
вать для подключения широкополосного гром-
коговорителя или сабвуфера. Выберите
настройку, подходящую для Вашего соедине-
ния.
1 Для отображения установочного меню на-
жмите M.C.
2 Поворачивайте M.C. для выбора настрой-
ки.
Можно выбрать любую настройку из сле-
дующего списка:
! REAR/SUB.W Выберите, если к выходу
заднего канала подсоединен широкопо-
лосный громкоговоритель, и также
имеется сабвуфер, подсоединенный к
выходу RCA.
! SUB.W/SUB.W Выберите, если сабву-
фер подключен напрямую к выходу за-
днего канала без дополнительного
усилителя, и также имеется сабвуфер,
подсоединенный к выходу RCA.
! REAR/REAR Выберите, если широко-
полосный громкоговоритель подсоеди-
нен к выходу заднего канала и к выходу
RCA.
Если к выходу заднего канала подсое-
динен широкополосный громкоговори-
тель, а выход RCA не используется,
можно выбрать REAR/SUB.W или REAR/
REAR.
Меню системы
1 Нажмите и удерживайте кнопку SRC/
OFF, пока устройство не выключится.
2 Нажмите кнопку SRC/OFF и удерживай-
те ее, пока не откроется стартовое меню.
3 Поворачивайте M.C. для прокрутки
пунктов меню; нажмите, чтобы выбрать
SYSTEM.
4 Для выбора функции меню системы
поворачивайте M.C.
Следующие выбранные функции меню си-
стемы можно настраивать.
Подробную информацию см. в
Меню систе-
мы
на стр. 88.
Использование
дополнительного
источника сигнала (AUX)
1 Вставьте мини-штекер стереокабеля в
гнездо AUX.
2 Нажмите кнопку SRC/OFF, чтобы вы-
брать AUX в качестве источника сигнала.
Примечание
Невозможно выбрать AUX, если не включе-
на вспомогательная настройка. Подробную
информацию см. в разделе
AUX (вспомога-
тельный вход)
на стр. 88.
Переключение дисплея
Выбор текстовой информации
1 Нажимайте DISP для выбора из следующих
функций:
! Название источника
! Название источника сигнала и часы
Если открылся неверный
экран
Отключите неверный экран, как описано
ниже.
1 Нажмите M.C., чтобы открыть главное
меню.
2 Поворачивайте M.C. для прокрутки
пунктов меню; нажмите, чтобы выбрать
SYSTEM.
3 Поверните M.C., чтобы отобразить
DEMO OFF, затем нажмите.
4 Поверните M.C. для выбора YES.
5 Нажмите M.C. для выбора.
Русский
Управление данным устройством
89
Раздел
Управление данным устройством
Ru
02
Black plate (90,1)
Соединения
Важно
! При установке данного устройства в авто-
мобиле, в котором отсутствует положение
ключа зажигания АСС, красный кабель
должен быть подключен к клемме, кото-
рая определяет рабочее положение
ключа зажигания; в противном случае
может возникнуть утечка тока аккумуля-
торной батареи.
O
N
S
T
A
R
T
O
F
F
Положение ACC Положение ACC от-
сутствует
! Эксплуатация данного устройства в усло-
виях, отличных от описанных ниже, может
привести к пожару или сбою в работе ус-
тройства.
Транспортные средства с 12-вольтовым
аккумулятором и заземлением отрица-
тельного полюса.
Громкоговорители с 50 Вт (выходная мощ-
ность) иот4 W до 8 W (сопротивление).
! Во избежание короткого замыкания, пере-
грева или неисправностей обязательно
соблюдайте следующие указания.
Перед установкой отсоедините отрица-
тельную клемму аккумулятора.
Закрепите провода при помощи зажимов
или изоляционной ленты. Для защиты
проводки заизолируйте провода в местах
их соприкосновения с металлическими де-
талями.
Разместите все кабели в удалении от под-
вижных деталей, таких как рычаг пере-
ключения передач и направляющие
сидений.
Разместите все кабели в удалении от на-
гревающихся деталей, таких как решетка
обогревателя.
Запрещается подключать желтый провод
дисплея к аккумуляторной батарее авто-
мобиля через сверленое отверстие в отсе-
ке двигателя.
Изолируйте концы всех не подсоединен-
ных кабелей изоляционной лентой.
Не укорачивайте кабели.
Никогда не срезайте изоляцию со шнура
питания данного устройства с целью пода-
чи питания на другое устройство. Допусти-
мая нагрузка кабеля по току ограничена.
Используйте предохранитель с указанны-
ми параметрами.
Запрещается напрямую заземлять отри-
цательный вывод громкоговорителя.
Запрещается связывать вместе отрица-
тельные кабели нескольких громкоговори-
телей.
! При включении питания устройства упра-
вляющий сигнал подается через сине-
белый провод. Подключите этот провод к
клемме пульта управления внешнего уси-
лителя мощности или клемме реле упра-
вления антенны с электроприводом
(макс. 300 мА 12 В постоянного тока).
Если автомобиль оборудован встроенной
в оконное стекло антенной, подсоедините
провод к клемме питания усилителя ан-
тенны.
! Запрещается подсоединять сине-белый
кабель к клемме питания внешнего усили-
теля мощности. Также запрещается под-
соединять данный провод к клемме
питания антенны с электроприводом. В
противном случае может возникнуть утеч-
ка тока аккумуляторной батареи или иная
неисправность.
! Черный кабель является заземляющим.
Заземляющие кабели данного устройства
и других устройств (особенно устройств,
предназначенных для эксплуатации при
больших токах, таких как усилитель мощ-
ности) должны монтироваться отдельно.
В противном случае их случайное отсое-
динение может привести к пожару или не-
исправности.
Данное устройство
3 45
21
1 Гнездо шнура питания
2 Выход заднего канала или выход сабву-
фера
3 Гнездо антенны
4 Плавкий предохранитель (10 A)
5 Вход проводного пульта дистанционного
управления
Служит для подключения проводного
адаптера пульта дистанционного упра-
вления (приобретается отдельно).
Шнур питания
1
3
3
2
4
4
5
5
6
6
b
8
9
7
a
e
d
c
1 К гнезду шнура питания
2 В зависимости от типа автомобиля функ-
ции 3 и 5 могут отличаться. В этом слу-
чае следует подключить 4 к 5 и 6 к 3.
3 Желтый
Резервный разъем (или разъем дополни-
тельного оборудования)
4 Желтый
Подключите к клемме источника постоян-
ного тока 12 В.
5 Красный
Разъем дополнительного оборудования
(или резервный разъем)
6 Красный
Подключите к клемме, на которую подает-
ся напряжение (12 В постоянного тока)
при включении зажигания.
7 Подсоедините провода одинакового
цвета друг к другу.
8 Черный (заземление на массу)
Установка
90
Раздел
Установка
Ru
03
Black plate (91,1)
9 Синий/белый
Расположение штекера разъема ISO на
различных автомобилях может отличать-
ся. Если штекер 5 предназначен для
управления антенной, подсоедините 9 к
b. На других автомобилях подключать 9
к b запрещается.
a Синий/белый
Подключите к клемме панели управления
усилителя мощности (макс. 300 мА 12 В
постоянного тока).
b Синий/белый
Подключите к клемме реле управления
антенны с электроприводом (макс.
300 мА 12 В постоянного тока).
c Желтый/черный
Если используется оборудование, имею-
щее функцию приглушения звука, данный
провод необходимо подсоединить к клем-
ме Audio Mute данного устройства. В про-
тивном случае необходимо проследить
за тем, чтобы данный провод не контакти-
ровал с любыми другими разъемами.
d Выводы громкоговорителей
Белый: Передний левый +
Белый/черный: Передний левый *
Серый: Передний правый +
Серый/черный: Передний правый *
Зеленый: Задний левый + или сабвуфер
+
Зеленый/черный: Задний левый * или
сабвуфер *
Фиолетовый: Задний правый + или саб-
вуфер +
Фиолетовый/черный: Задний правый *
или сабвуфер *
e Разъем ISO
В некоторых автомобилях разъем ISO
может иметь два вывода. В этом случае
необходимо подсоединить оба разъема.
Примечания
! Требуется изменение стартового меню
данного устройства. См.
SP-P/O MODE
(настройка выхода заднего канала и
предварительного усилителя)
на стр. 89.
Выход сабвуфера данного устройства мо-
нофонический.
! При использовании сабвуфера мощно-
стью 70 Вт (2 W) обязательно подсоедини-
те к сабвуферу фиолетовый и
фиолетовый/черный провод данного ус-
тройства. Не подсоединяйте зеленый и
зеленый/черный провода.
Усилитель мощности
(приобретается отдельно)
Используйте данную схему подсоединения
при использовании дополнительного усили-
теля мощности.
1
3
2
4
55
1 Пульт дистанционного управления систе-
мой
Подсоедините синий/белый кабель.
2 Усилитель мощности (приобретается от-
дельно)
3 Подключите с помощью кабелей RCA
(приобретаются отдельно)
4 К выходу заднего канала или выходу саб-
вуфера
5 Задний громкоговоритель или сабвуфер
Установка
Важно
! Перед окончательной установкой про-
верьте все соединения и системы.
! Не используйте детали, не разрешенные
производителем к использованию, по-
скольку это может стать причиной неис-
правностей.
! Уточните у дилера компании, требует ли
установка сверления отверстий или вне-
сения иных изменений в конструкцию ав-
томобиля.
! Не устанавливайте данное устройство в
местах, где оно может:
помешать управлению автомобилем.
травмировать пассажира при внезапной
остановке автомобиля.
! Перегрев полупроводникового лазера
приведет к его выходу из строя. Разме-
стите все кабели в удалении от нагреваю-
щихся деталей, таких как решетка
обогревателя.
! Оптимальной является установка устрой-
ства под углом менее 60°.
60°
! При установке необходимо обеспечить
эффективный отвод тепла, оставив до-
статочное пространство за задней пане-
лью и закрепив свободные кабели так,
чтобы они не закрывали вентиляционные
отверстия.
5cmcm
5 см
5 см
Оставить
просторное
место
Переднее/заднее крепление
стандарта DIN
Для данного изделия предусмотрена воз-
можность установки с помощью переднего
или заднего крепления.
При установке используйте детали, имею-
щиеся в продаже.
Переднее крепление стандарта DIN
1 Вставьте монтажную обойму в пере-
днюю панель.
При установке в недостаточно глубоком
гнезде используйте монтажную обойму, вхо-
дящую в комплект поставки устройства. При
наличии достаточного пространства за ус-
тройством применяется монтажная обойма,
поставляемая вместе с автомобилем.
2 Закрепите обойму, подогнув с по-
мощью отвертки металлические язычки
(90°).
1
2
1 Приборная панель
2 Монтажная обойма
# Убедитесь, что устройство надежно закрепле-
но в гнезде. Неустойчивость устройства может
привести к его выпадению и неполадкам в рабо-
те.
Русский
Установка
91
Раздел
Установка
Ru
03
Black plate (92,1)
Заднее крепление стандарта DIN
1 Совместите отверстия на кронштейне
и боковых панелях устройства.
2 Затяните по два винта с каждой сторо-
ны.
1
2
3
1 Самонарезающий винт (5 мм ×8мм)
2 Монтажная рамка
3 Приборная панель или консоль
Демонтаж устройства
1 Снимите рамку.
1 Декоративная рамка
2 Язычок
! Снятие передней панели облегчает до-
ступ к декоративной рамке.
! При установке декоративной рамки сторо-
на рамки с язычком должна быть направ-
лена вниз.
2 Вставьте прилагаемые экстракторы с
обеих сторон устройства до щелчка.
3 Вытяните устройство из приборной
панели автомобиля.
Снятие и установка передней панели
В целях защиты от кражи переднюю панель
можно снять.
Нажмите на кнопку снятия панели и потяните
панель вверх и на себя.
Чтобы получить дополнительную информа-
цию, см.
Снятие передней панели в целях за-
щиты от кражи
и
Установка передней панели
на стр. 84.
Устранение неисправностей
Признак Причина Действие
Дисплей ав-
томатически
возвращает-
ся в исход-
ный режим.
В течение 30
секунд не
было выполне-
но никаких
операций.
Повторите опе-
рацию.
Диапазон по-
вторного
воспроизве-
дения само-
произвольно
изменяется.
В зависимости
от выбранного
диапазона вос-
произведения
он может изме-
няться при вы-
боре другой
папки или до-
рожки, а также
при перемотке
вперед/назад.
Выберите диа-
пазон повторно-
го воспроизве-
дения еще раз.
Вложенная
папка не вос-
производит-
ся.
Вложенные
папки не вос-
производятся,
если выбран
диапазон FLD
(повторное
воспроизведе-
ние папки).
Выберите дру-
гой диапазон по-
вторного вос-
произведения.
При измене-
нии дисплея
отображает-
ся NO XXXX
(например,
NO TITLE).
Текстовая ин-
формация от-
сутствует.
Переключите
дисплей или
включите вос-
произведение
другой дорожки/
файла.
Признак Причина Действие
Устройство
функциони-
рует с ошиб-
ками.
Имеются по-
мехи.
Рядом с ус-
тройством ис-
пользуется
прибор, пере-
дающий элек-
тромагнитные
волны, напри-
мер, сотовый
телефон.
Уберите прибор,
вызывающий по-
мехи, от этого
устройства.
Сообщения об ошибках
Прежде чем обратиться к торговому пред-
ставителю или в ближайший сервисный
центр Pioneer, обязательно запомните сооб-
щение об ошибке.
Общие
Сообщение Причина Действие
AMP ERROR Устройство не
работает или
неправильно
подсоединен
громкоговори-
тель; сработа-
ла цепь
защиты.
Проверьте, под-
ключен ли гром-
коговоритель.
Если сообщение
не исчезает
даже после вы-
ключения/вы-
ключения зажи-
гания, свяжитесь
с дилерским
центром или ав-
торизованным
сервисным цен-
тром Pioneer.
Установка
92
Раздел
Дополнительная информация
Ru
03
Black plate (93,1)
Проигрыватель компакт-дисков
Сообщение Причина Действие
ERROR-07,
11, 12, 17, 30
Диск загряз-
нен.
Очистите диск.
Диск поцара-
пан.
Замените диск.
ERROR-07,
10, 11, 12,
15, 17, 30,
A0
Электрическая
или механиче-
ская неисправ-
ность.
Установите ключ
зажигания в по-
ложение OFF, а
затем в поло-
жение ON или
переключитесь
на другой источ-
ник сигнала, а
затем обратно
на проигрыва-
тель компакт-
дисков.
ERROR-15 Вставлен пу-
стой диск.
Замените диск.
ERROR-23 Формат диска
не поддержи-
вается.
Замените диск.
FORMAT
READ
Иногда проис-
ходит задерж-
ка между
началом вос-
произведения
и появлением
звука.
Звук появится
после того как с
дисплея исчез-
нет сообщение.
NO AUDIO На диске от-
сутствуют
файлы, кото-
рые можно
воспроизве-
сти.
Замените диск.
SKIPPED Диск содержит
файлы, защи-
щенные техно-
логией DRM.
Замените диск.
Сообщение Причина Действие
PROTECT Все файлы на
диске защище-
ны техноло-
гией DRM.
Замените диск.
Рекомендации по
обращению с изделием
Диски и проигрыватель
Используйте только диски, имеющие один из
следующих логотипов.
Используйте диски диаметром 12 см. Не ис-
пользуйте диски диаметром 8 см и адаптеры
для воспроизведения таких дисков.
Используйте только обычные круглые диски.
Не используйте диски необычной формы.
Не вставляйте в щель для загрузки компакт-
диска ничего, кроме компакт-диска.
Не используйте диски с трещинами, отколоты-
ми краями, деформированные диски или
диски с другими повреждениями, поскольку
такие диски могут повредить проигрыватель.
Не закрытые для записи диски CD-R/CD-RW
воспроизвести нельзя.
Не прикасайтесь к записанной поверхности
дисков.
Когда диски не используются, храните их в
футлярах.
Не приклеивайте этикеток, не пишите и не на-
носите химических веществ на поверхность
дисков.
Для очистки компакт-диска протрите диск мяг-
кой тканью от центра к краю.
Конденсация может временно ухудшить рабо-
ту проигрывателя. Оставьте его для адаптации
к более высокой температуре примерно на
час. Также удалите влагу с дисков с помощью
мягкой ткани.
Воспроизведение дисков может быть невоз-
можно из-за характеристик диска, формата
диска, приложения, при помощи которого вы-
полнялась запись, условий воспроизведения,
условий хранения и других факторов.
Толчки от неровностей дороги могут вызвать
прерывание воспроизведения диска.
Перед использованием дисков ознакомьтесь с
мерами предосторожности при обращении с
ними.
При использовании дисков, на поверхность ко-
торых могут наноситься этикетки, изучите ин-
струкции и предупреждения для этих дисков.
Установка и извлечение некоторых дисков
могут быть невозможны. Использование таких
дисков может привести к повреждению обору-
дования.
Не приклеивайте на диски этикетки и другие
материалы.
! Это может деформировать диски, в резуль-
тате чего их воспроизведение будет невоз-
можным.
! Этикетки могут отклеиться во время вос-
произведения и затруднить извлечение
дисков, а также повредить оборудование.
Диски формата DualDisc
DualDisc это двусторонние диски для записи
аудиоданных на CD с одной стороны и видео-
данных на DVD с другой.
Поскольку сторона CD двойных дисков физи-
чески несовместима с общим стандартом ком-
пакт-дисков, ее воспроизведение на данном
устройстве может быть невозможным.
Частая загрузка и извлечение двойного диска
может привести к появлению царапин на
диске. Серьезные царапины могут создать
проблемы при воспроизведении диска на дан-
ном устройстве. В некоторых случаях двойной
диск может застревать в щели загрузки дисков,
из-за чего его становится невозможно извлечь.
Во избежание такой ситуации мы рекомендуем
воздержаться от использования двойных дис-
ков в данном устройстве.
За более подробной информацией о двойных
дисках обращайтесь к соответствующим про-
изводителям.
Совместимость с
форматами сжатия данных
WMA
Расширение: .wma
Скорость передачи данных: от 48 кбит/сдо
320 кбит/с (постоянная), от 48 кбит/сдо
384 кбит/с (переменная)
Частота дискретизации:32кГц, 44,1 кГц,48
кГц
Windows Media Audio Professional, Lossless,
Voice/DRM Stream/Stream с поддержкой видео:
не поддерживается
Русский
Дополнительная информация
93
Приложение
Дополнительная информация
Ru
Black plate (94,1)
MP3
Расширение: .mp3
Скорость передачи данных: от 8 кбит/сдо
320 кбит/с (постоянная), переменная
Частота дискретизации: от 8 кГц до 48 кГц
(32 кГц, 44,1 кГц,48кГц пиковая)
Совместимая версия тегов ID3: 1.0, 1.1, 2.2,
2.3, 2.4 (теги ID3 версии 2.x имеют приоритет
перед версией 1.x.)
Списки воспроизведения M3u: не поддержи-
ваются
MP3i (интерактивный MP3), mp3 PRO: не под-
держиваются
WAV
Расширение: .wav
Разрядность квантования:8и 16 (LPCM), 4
(MS ADPCM)
Частота дискретизации: от 16 кГц до 48 кГц
(LPCM), 22,05 кГц и 44,1 кГц (MS ADPCM)
Дополнительная информация
В качестве названия файла или папки могут
отображаться только первые 32 символа
(включая расширение).
Для отображения в данном устройстве коди-
ровка русского текста должна соответствовать
одному из следующих наборов символов:
! Юникод (UTF-8, UTF-16)
! Отличный от Юникода набор символов, ис-
пользующийся в среде Windows, для кото-
рого в языковой настройке задан русский
язык
Это устройство может неверно воспроизво-
дить некоторые файлы формата WMA в зави-
симости от приложений, использованных для
их записи.
Диск
Допустимая иерархия папок: до восьми уров-
ней (реальная иерархия папок составляет
менее двух уровней)
Количество воспроизводимых папок: не более
99
Количество воспроизводимых файлов: не
более 999
Файловая система: ISO 9660 уровень 1 и 2,
Romeo, Joliet
Воспроизведение нескольких сессий: поддер-
живается
Пакетный формат записи: не поддерживается
Независимо от продолжительности паузы
между композициями в изначальной записи,
при воспроизведении дисков со сжатыми ауди-
офайлами между композициями будут корот-
кие паузы.
ВНИМАНИЕ
Не оставляйте диски в местах с высокой тем-
пературой.
Последовательность
воспроизведения
аудиофайлов
Пользователь не может назначать номера
папок и устанавливать последовательность
воспроизведения с помощью данного ус-
тройства.
Пример иерархии
1
2
3
4
5
6
01
02
03
04
05
: Папка
: Сжатый ауди-
офайл
от 01 до 05: Номер
папки
от 1 до 6: После-
довательность
воспроизведения
Диск
Последовательность выбора папок и других
действий может отличаться в зависимости
от кодировки или программного обеспече-
ния, использованного для записи.
Таблица символов для
русского языка
Д: БД: БД: БД: БД: Б
: А : Б : В : Г : Д
: Е, Ё : Ж : З : И, Й : К
: Л : М : Н : О : П
: Р : С : Т : У : Ф
Д: БД: БД: БД: БД: Б
: Х : Ц : Ч
: Ш,
Щ
: Ъ
: Ы : Ь : Э : Ю : Я
Д: Дисплей Б: Буква
Авторское право и
товарные знаки
iTunes
Apple и iTunes являются торговыми знаками
компании Apple Inc., зарегистрированными в
США и других странах.
MP3
Поставка этого изделия дает право только на
его частное и некоммерческое использова-
ние и не предоставляет лицензии и не подра-
зумевает право использования этого
изделия в любых коммерческих (т.е. прино-
сящих прибыль) прямых трансляциях (теле-
визионных, спутниковых, кабельных и/или
любых других), вещании/потоковой передаче
через Интернет, локальных сетях и/или дру-
гих сетях или в других электронных системах
распространения, таких как системы платно-
го аудио и аудио по запросу. Для такого ис-
пользования необходима специальная
лицензия. Дополнительную информацию см.
на сайте
http://www.mp3licensing.com.
WMA
Windows Media это зарегистрированная
торговая марка или торговая марка Microsoft
Corporation в США и/или других странах.
Дополнительная информация
94
Приложение
Дополнительная информация
Ru
Black plate (95,1)
В данном изделии используются технологии,
принадлежащие корпорации Microsoft, кото-
рые не разрешается использовать или рас-
пространять без лицензии от Microsoft
Licensing, Inc.
Серийный номер
На этом рисунке показана информация о месяце и годе изготовления устройства.
L
Го д
Го д
Символ
2001 2002 2003 2004 2005 2006 2007 2008 2009 2010
2011 2012 2013 2014 2015 2016 2017 2018 2019 2020
K LMNO P QRS T
ABCDEFGH I JСимвол
P1 - Год изготовления
1
Символ
2345 6 7 89 1110 12
ABCDEFGH I JKL
Месяц
P2 - Месяц изготовления
12 цифр
P1 P2
Дата изготовления оборудования
2 цифры
10 цифр
Технические
характеристики
Общие
Источник питания ........... 14,4 В постоянного тока (до-
пустимый диапазон от 10,8
Вдо15,1 В)
Система заземления ..... Заземление отрицательно-
го полюса
Максимальный потребляемый ток
................................... 10,0 А
Размеры (Ш × В × Г):
DIN
Шасси ............... 178 мм ×50мм × 165 мм
Передняя панель
..................... 188 мм ×58мм ×16мм
D
Шасси ............... 178 мм ×50мм × 165 мм
Передняя панель
..................... 170 мм ×46мм ×16мм
Масса ............................. 1 кг
Аудио
Максимальная выходная мощность
................................... 50 Вт ×4
70 Вт × 1/2 W (для сабвуфе-
ра)
Номинальная выходная мощность
................................... 22 Вт ×4(от 50 Гц до
15 000 Гц, суммарное значе-
ние коэффициента нели-
нейных искажений 5%,
нагрузка 4 W для обоих ка-
налов)
Сопротивление нагрузки
................................... 4 W (допустимо от 4 W до
8 W )
Максимальная выходная мощность
................................... 2,0 В
Контур громкости ........... +10 дБ (100 Гц), +6,5 дБ
(10 кГц)(громкость: 30 дБ)
Эквалайзер (5-полосный графический эквалайзер):
Частота .................... 80 Гц/250 Гц/800 Гц/
2,5 кГц/8 кГц
Диапазон амплитудно-частотных характери-
стик .......................... ±12 дБ (сшагом2 дБ)
Сабвуфер (моно):
Частота .................... 50 Гц/63 Гц/80 Гц/100 Гц/
125 Гц/160 Гц/200 Гц
Крутизна характеристики
............................ 6 дБ/окт, 12 дБ/окт
Усиление ................. +6 дБ до 24 дБ
Фаза ........................ Нормальная/Обратная
Проигрыватель компакт-дисков
Система ......................... Аудиосистема с компакт-ди-
ском
Используемые диски ..... Компакт-диск
Отношение сигнал/шум
................................... 94 дБ (1 кГц)(сеть IEC-A)
Число каналов ............... 2(стерео)
Формат декодирования файлов MP3
................................... MPEG- 1 и 2 Audio Layer 3
Формат декодирования файлов WMA
................................... Версии 7, 7.1, 8, 9, 10, 11, 12
(двухканальный звук)
(Windows Media Player)
Формат сигнала WAV ..... Linear PCM и MS ADPCM
(без компрессии)
FM-тюнер
Диапазон частот ............. от 87,5 МГц до 108,0 МГц
Полезная чувствительность
................................... 9 дБф (0,8 мкВ/75 W, моно,
отношение сигнал/шум:
30 дБ)
Отношение сигнал/шум
................................... 72 дБ (сеть IEC-A)
MW-тюнер
Диапазон частот ............. от 531 кГц до 1 602 кГц
Полезная чувствительность
................................... 25 мкВ (отношение сигнал/
шум:20дБ)
Отношение сигнал/шум
................................... 62 дБ (сеть IEC-A)
LW-тюнер
Диапазон частот ............. от 153 кГц до 281 кГц
Полезная чувствительность
................................... 28 мкВ (отношение сигнал/
шум:20дБ)
Отношение сигнал/шум
................................... 62 дБ (сеть IEC-A)
Примечание:
В соответствии со статьей 5 закона Рос-
сийской Федерации «О защите прав по-
требителей» и постановлением
правительства Российской Федерации
720 от 16.06.97 компания Pioneer Europe
NV оговаривает следующий срок службы
изделий, официально поставляемых на
российский рынок.
Автомобильная электроника:6лет
Прочие изделия (наушники, микрофоны
ит.п.): 5 лет
Примечания
! Характеристики и конструкция могут быть
изменены без предварительного уведо-
мления.
! Данное устройство произведено в Таи-
ланде.
Русский
Дополнительная информация
95
Приложение
Дополнительная информация
Ru
Black plate (96,1)
PIONEER CORPORATION
28-8, Honkomagome 2-chome, Bunkyo-ku,
Tokyo 113-0021, JAPAN
Корпорация Пайонир
28-8, Хонкомагомэ 2-чоме, Бункё-ку,
Токио 113-0021, Япония
Импортер ООО ПИОНЕР РУС
105064, Россия, г. Москва, Нижний Сусальный переулок, дом 5, строение
19
Тел.: +7(495) 956-89-01
PIONEER EUROPE NV
Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium/Belgique
TEL: (0) 3/570.05.11
PIONEER ELECTRONICS (USA) INC.
P.O. Box 1540, Long Beach, California 90801-1540, U.S.A.
TEL: (800) 421-1404
PIONEER ELECTRONICS OF CANADA, INC.
340 Ferrier Street, Unit 2, Markham, Ontario L3R 2Z5, Canada
TEL: 1-877-283-5901
TEL: 905-479-4411
PIONEER ELECTRONICS ASIACENTRE PTE. LTD.
2 Jalan Kilang Barat, #07-01, Singapore 159346
TEL: 65-6378-7888
PIONEER ELECTRONICS AUSTRALIA PTY. LTD.
5 Arco Lane, Heatherton, Victoria, 3202 Australia
TEL: (03) 9586-6300
PIONEER ELECTRONICS DE MÉXICO S.A. de C.V.
Blvd.Manuel Ávila Camacho 138, 10 piso
Col.Lomas de Chapultepec, México, D.F. 11000
TEL: 52-55-9178-4270
FAX: 52-55-5202-3714
台北4078
886-(0)2-2657-3588
9095
852-2848-6488
ã 2012-2016 PIONEER CORPORATION. All rights reserved.
ã 2012-2016 PIONEER CORPORATION. Tous droits de reproduction et de traduction réservés.
ã PIONEER CORPORATION, 2012-2016. Все права защищены.
<QRD3143-C> EW
<KOKZ14D>

Documenttranscriptie

Black plate (1,1) Français Español Deutsch Owner’s Manual Mode d’emploi Manuale d’istruzioni Manual de instrucciones Bedienungsanleitung Handleiding Руководство пользователя Italiano DEH-150MP DEH-150MPG English CD RDS RECEIVER AUTORADIO CD RDS SINTOLETTORE CD RDS REPRODUCTOR DE CD CON RECEPTOR RDS CD RDS-EMPFÄNGER CD RDS-ONTVANGER CD RDS ПРИЕМНИК Nederlands Русский <QRD3143-C> 1 Black plate (2,1) Section Before you start 01 Operating this unit 02 Thank you for purchasing this PIONEER product To ensure proper use, please read through this manual before using this product. It is especially important that you read and observe WARNINGs and CAUTIONs in this manual. Please keep the manual in a safe and accessible place for future reference. About this unit Head unit The tuner frequencies on this unit are allocated for use in Western Europe, Asia, the Middle East, Africa and Oceania. Use in other areas may result in poor reception. The RDS (radio data system) function only operates in areas with broadcasting RDS signals for FM stations. 7 8 CAUTION This product is a class 1 laser product classified under the Safety of laser products, IEC 60825-1:2007. If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling. Private households in the member states of the EU, in Switzerland and Norway may return their used electronic products free of charge to designated collection facilities or to a retailer (if you purchase a similar new one). For countries not mentioned above, please contact your local authorities for the correct method of disposal. By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health. 2 CAUTION ! Do not allow this unit to come into contact with liquids. Electrical shock could result. Also, damage to this unit, smoke, and overheating could result from contact with liquids. ! The Pioneer CarStereo-Pass is for use only in Germany. ! Always keep the volume low enough to hear outside sounds. ! Avoid exposure to moisture. ! If the battery is disconnected or discharged, any preset memory will be erased. Note Function setting operations are completed even if the menu is canceled before the operations are confirmed. Indicator 1 2 34 5 6 9 a 1 b Part c d h (eject) 8 BAND 2 SRC/OFF 9 (back)/ DIMMER (dimmer) 3 MULTI-CONTROL (M.C.) a c/d b 1/ 4 (list) to 6/ 5 DISP c AUX input jack (3.5 mm stereo jack) 6 Disc loading slot d Detach button 7 2 Sub information section Sub information is displayed. 3 TA (traffic announcements) TA function is on. 4 TP (traffic program identification) A TP station is tuned in. Part 1 (list) 5 (sound retriever) 6 LOC 7 8 (repeat) 9 1 2 3 4 5 6 8 7 a 9 The sound retriever function is on. Local seek tuning is on. Track or folder repeat is on. (random) Random play is on. Main information section ! Tuner: band and frequency ! RDS: program service name, PTY information and other literal information ! CD player: elapsed playback time and text information (equalizer) Display indication State The list function is being operated. Appears when a lower tier of folder or menu exists. a In case of trouble Set up menu Should this unit fail to operate properly, please contact your dealer or nearest authorized PIONEER Service Station. When you turn the ignition switch to ON after installation, set up menu appears on the display. You can set up the menu options below. En <QRD3143-C> 2 Black plate (3,1) Section Operating this unit 2 Turn M.C. to switch to YES. # If you do not operate for 30 seconds, the set up menu will not be displayed. # If you prefer not to set up at this time, turn M.C. to switch to NO. Press to select. If you select NO, you cannot set up in the set up menu. 3 Press M.C. to select. 4 Perform the following procedures to set the menu. To proceed to the next menu option, you need to confirm your selection. LANGUAGE (multi-language) This unit can display the text information from a compressed audio file even for information embedded in English or Russian. ! If the embedded language and the selected language setting are not the same, text information may not display properly. ! Some characters may not be displayed properly. 1 Turn M.C. to select the desired setting. ENG (English)—РУС (Russian) 2 Press M.C. to confirm the selection. CLOCK SET (setting the clock) 1 2 3 4 Turn M.C. to adjust hour. Press M.C. to select minute. Turn M.C. to adjust minute. Press M.C. to confirm the selection. FM STEP (FM tuning step) Normally, the FM tuning step employed by seek tuning is 50 kHz. When AF or TA is on, the tuning step automatically changes to 100 kHz. It may be preferable to set the tuning step to 50 kHz when AF is on. ! The tuning step remains at 50 kHz during manual tuning. 1 Turn M.C. to select the FM tuning step. 50 (50 kHz)—100 (100 kHz) 2 Press M.C. to confirm the selection. QUIT appears. 5 To finish your settings, turn M.C. to select YES. # If you prefer to change your setting again, turn M.C. to switch to NO. Press to select. 6 Removing the front panel to protect your unit from theft 1 Press the detach button to release the front panel. 2 Push the front panel upward (M) and then pull it toward (N) you. Basic operations Important ! Handle gently when removing or attaching the front panel. ! Avoid subjecting the front panel to excessive shock. ! Keep the front panel out of direct sunlight and high temperatures. ! To avoid damaging the device or vehicle interior, remove any cables and devices attached to the front panel before detaching it. Selecting a source 1 Press SRC/OFF to cycle between: TUNER (tuner)—CD (CD player)—AUX (AUX) Adjusting the volume 1 Turn M.C. to adjust the volume. CAUTION For safety reasons, park your vehicle when removing the front panel. 3 Always keep the detached front panel in a protection device such as a protection case. Re-attaching the front panel 1 Slide the front panel to the left. Make sure to insert the tabs on the left side of the head unit into the slots on the front panel. Note When this unit’s blue/white lead is connected to the vehicle’s auto-antenna relay control terminal, the vehicle’s antenna extends when this unit’s source is turned on. To retract the antenna, turn the source off. Frequently used menu operations Press M.C. to select. Notes ! You can set up the menu options from the system menu. For details about the settings, refer to System menu on page 6. ! You can cancel set up menu by pressing SRC/OFF. 02 English 1 After installation of this unit, turn the ignition switch to ON. SET UP appears. Operating this unit 2 Press the right side of the front panel until it is firmly seated. If you cannot attach the front panel to the head unit successfully, make sure that you are placing the front panel onto the head unit correctly. Forcing the front panel into place may result in damage to the front panel or head unit. Returning to the previous display Returning to the previous list (the folder one level higher) 1 Press /DIMMER. Returning to the ordinary display Canceling the main menu 1 Press BAND. Returning to the ordinary display from the list 1 Press BAND. Turning the unit on 1 Press SRC/OFF to turn the unit on. Turning the unit off 1 Press and hold SRC/OFF until the unit turns off. En <QRD3143-C> 3 3 Black plate (4,1) Section Operating this unit 02 Tuner Operating this unit 2 Press one of the preset tuning buttons (1/ to 6/ ) to select the desired station. Basic operations Switching the display Selecting a band 1 Press BAND until the desired band (FM1, FM2, FM3 for FM or MW/LW) is displayed. Switching preset stations 1 Press c or d. ! Select PCH (preset channel) under SEEK to use this function. For details about the settings, refer to SEEK (left/right key setting) on the next page. Manual tuning (step by step) 1 Press c or d. ! Select MAN (manual tuning) under SEEK to use this function. For details about the settings, refer to SEEK (left/right key setting) on the next page. Seeking 1 Press and hold c or d, and then release. You can cancel seek tuning by briefly pressing c or d. While pressing and holding c or d, you can skip stations. Seek tuning starts as soon as you release c or d. Note This unit’s AF (alternative frequencies search) function can be turned on and off. AF should be off for normal tuning operation (refer to AF (alternative frequencies search) on the next page). Storing and recalling stations for each band Using preset tuning buttons Selecting the desired text information 1 Press DISP to cycle between the following: ! FREQUENCY (program service name or frequency) ! BRDCST INFO (program service name/PTY information) ! CLOCK (source name and clock) Notes ! If the program service name cannot be acquired in FREQUENCY, the broadcast frequency is displayed instead. If the program service name is detected, the program service name will be displayed. ! BRDCST INFO text information will change automatically. ! Depending on the band, text information can be changed. ! Text information items that can be changed depend on the area. Using PTY functions You can tune in to a station using PTY (program type) information. Searching for an RDS station by PTY information You can search for general types of broadcasting programs, such as those listed in the following section. Refer to this page. (list). 1 Press 2 Turn M.C. to select a program type. NEWS/INFO—POPULAR—CLASSICS— OTHERS 3 Press M.C. to begin the search. The unit searches for a station broadcasting that type of program. When a station is found, its program service name is displayed. ! To cancel the search, press M.C. again. ! The program of some stations may differ from that indicated by the transmitted PTY. ! If no station is broadcasting the type of program you searched for, NOT FOUND is displayed for about two seconds and then the tuner returns to the original station. OTHERS (others) EDUCATE (Education), DRAMA (Drama), CULTURE (Culture), SCIENCE (Science), VARIED (Varied), CHILDREN (Children’s), SOCIAL (Social affairs), RELIGION (Religion), PHONE IN (Phone in), TOURING (Travel), LEISURE (Leisure), DOCUMENT (Documentaries) Function settings 1 Press M.C. to display the main menu. 2 Turn M.C. to change the menu option and press to select FUNCTION. 3 Turn M.C. to select the function. Once selected, the following functions can be adjusted. # If MW/LW band is selected, only BSM, LOCAL and SEEK are available. PTY list BSM (best stations memory) NEWS/INFO (news and information) NEWS (News), AFFAIRS (Current affairs), INFO (Information), SPORT (Sports), WEATHER (Weather), FINANCE (Finance) BSM (best stations memory) automatically stores the six strongest stations in the order of their signal strength. 1 Press M.C. to turn BSM on. To cancel, press M.C. again. POPULAR (popular) POP MUS (Popular music), ROCK MUS (Rock music), EASY MUS (Easy listening), OTH MUS (Other music), JAZZ (Jazz), COUNTRY (Country music), NAT MUS (National music), OLDIES (Oldies music), FOLK MUS (Folk music) REGION (regional) When AF is used, the regional function limits the selection of stations to those broadcasting regional programs. 1 Press M.C. to turn the regional function on or off. CLASSICS (classics) LOCAL (local seek tuning) L. CLASS (Light classical), CLASSIC (Classical) 1 When you find a station that you want to store in memory, press one of the preset tuning buttons (1/ to 6/ ) and hold until the preset number stops flashing. 4 En <QRD3143-C> 4 Black plate (5,1) Section Operating this unit TA (traffic announcement standby) 1 Press M.C. to turn traffic announcement standby on or off. AF (alternative frequencies search) 1 Press M.C. to turn AF on or off. NEWS (news program interruption) 1 Press M.C. to turn the NEWS function on or off. SEEK (left/right key setting) You can assign a function to the left and right keys of the unit. Select MAN (manual tuning) to tune up or down manually or select PCH (preset channel) to switch between preset channels. 1 Press M.C. to select MAN or PCH. CD/CD-R/CD-RW Basic operations Playing a CD/CD-R/CD-RW 1 Insert the disc into the disc loading slot with the label side up. Ejecting a CD/CD-R/CD-RW 1 Press h. Selecting a folder 1 Press 1/ or 2/ . Selecting a track 1 Press c or d. Fast forwarding or reversing 1 Press and hold c or d. ! When playing compressed audio, there is no sound during fast forward or reverse. ! Depending on the version of iTunes used to write MP3 files to a disc or media file types, incompatible text stored within an audio file may be displayed incorrectly. ! Text information items that can be changed depend on the media. Returning to root folder 1 Press and hold BAND. Selecting and playing files/ tracks from the name list Switching between compressed audio and CD-DA 1 Press BAND. 1 Press list mode. Switching the display Selecting the desired text information 1 Press DISP to cycle between the following: CD-DA ! ELAPSED TIME (track number and playback time) ! CLOCK (source name and clock) ! SPEANA (spectrum analyzer) CD-TEXT ! TRACK INFO (track title/track artist/disc title) ! ELAPSED TIME (track number and playback time) ! CLOCK (source name and clock) ! SPEANA (spectrum analyzer) MP3/WMA/WAV ! TRACK INFO (track title/artist name/album title) ! FILE INFO (file name/folder name) ! ELAPSED TIME (track number and playback time) ! CLOCK (source name and clock) ! SPEANA (spectrum analyzer) Notes ! TRACK INFO and FILE INFO text information will change automatically. to switch to the file/track name 2 Use M.C. to select the desired file name (or folder name). Selecting a file or folder 1 Turn M.C. Playing 1 When a file or track is selected, press M.C. Viewing a list of the files (or folders) in the selected folder 1 When a folder is selected, press M.C. Playing a song in the selected folder 1 When a folder is selected, press and hold M.C. Operations using special buttons Selecting a repeat play range to cycle between the following: 1 Press 6/ ! ALL – Repeat all tracks ! ONE – Repeat the current track ! FLD – Repeat the current folder Playing tracks in random order to turn random play on or off. 1 Press 5/ Tracks in a selected repeat range are played in random order. ! To change songs during random play, press d to switch to the next track. Pressing c restarts playback of the current track from the beginning of the song. 02 Pausing playback 1 Press 4/PAUSE to pause or resume. English Local seek tuning lets you tune in to only those radio stations with sufficiently strong signals for good reception. 1 Press M.C. to select the desired setting. FM: OFF—LV1—LV2—LV3—LV4 MW/LW: OFF—LV1—LV2 The highest level setting allows reception of only the strongest stations, while lower levels allow the reception of weaker stations. Operating this unit Enhancing compressed audio and restoring rich sound (sound retriever) 1 Press 3/S.Rtrv to cycle between: 1—2—OFF (off) 1 is effective for low compression rates, and 2 is effective for high compression rates. Function settings 1 Press M.C. to display the main menu. 2 Turn M.C. to change the menu option and press to select FUNCTION. Once selected, the function below can be adjusted. S.RTRV (sound retriever) Automatically enhances compressed audio and restores rich sound. 1 Press M.C. to select the desired setting. For details, refer to Enhancing compressed audio and restoring rich sound (sound retriever) on this page. Audio adjustments 1 Press M.C. to display the main menu. 2 Turn M.C. to change the menu option and press to select AUDIO. 3 Turn M.C. to select the audio function. Once selected, the following audio functions can be adjusted. ! FADER is not available when SUB.W/SUB.W is selected in SP-P/O MODE. For details, refer to SP-P/O MODE (rear output and preout setting) on page 7. En <QRD3143-C> 5 5 Black plate (6,1) Section Operating this unit 02 ! SUB.W, SUB.W CTRL and HPF SETTING are not available when REAR/REAR is selected in SP-P/O MODE. For details, refer to SP-P/O MODE (rear output and preout setting) on the next page. ! SUB.W CTRL and HPF SETTING are not available when SUB.W is selected in OFF. For details, refer to SUB.W (subwoofer on/off setting) on this page. FADER (fader adjustment) 1 Press M.C. to display the setting mode. 2 Turn M.C. to adjust the front/rear speaker balance. BALANCE (balance adjustment) 1 Press M.C. to display the setting mode. 2 Turn M.C. to adjust the left/right speaker balance. EQ SETTING (equalizer recall) Operating this unit 1 Press M.C. to display the setting mode. 2 Turn M.C. to select the equalizer. POWERFUL—NATURAL—VOCAL—CUSTOM1—CUSTOM2—FLAT—SUPER BASS The equalizer band and equalizer level can be customized when CUSTOM1 or CUSTOM2 is selected. If selecting CUSTOM1 or CUSTOM2, complete the procedures outlined below. If selecting other options, press M.C. to return to the previous display. ! CUSTOM1 can be set separately for each source. ! CUSTOM2 is a shared setting used in common for all sources. 3 Press M.C. to display the setting mode. 4 Press M.C. to cycle between the following: Equalizer band—Equalizer level 5 Turn M.C. to select the desired setting. Equalizer band: 80HZ—250HZ—800HZ— 2.5KHZ—8KHZ Equalizer level: +6 to –6 ! You can also switch the equalizer by pressing repeatedly. LOUDNESS (loudness) Loudness compensates for deficiencies in the lowfrequency and high-frequency ranges at low volume. 1 Press M.C. to select the desired setting. OFF (off)—LOW (low)—MID (mid)—HI (high) SUB.W (subwoofer on/off setting) This unit is equipped with a subwoofer output which can be turned on or off. 1 Press M.C. to select the desired setting. NOR (normal phase)—REV (reverse phase)— OFF (subwoofer off) Only frequencies lower than those in the selected range are outputted from the subwoofer. 1 Press M.C. to display the setting mode. 2 Press M.C. to cycle between the following: Cut-off frequency—Output level—Slope level Rates that can be adjusted will flash. 3 Turn M.C. to select the desired setting. Cut-off frequency: 50HZ—63HZ—80HZ— 100HZ—125HZ—160HZ—200HZ Output level: –24 to +6 Slope level: –6— –12 BASS BOOST (bass boost) 1 Press M.C. to display the setting mode. 2 Turn M.C. to select a desired level. 0 to +6 is displayed as the level is increased or decreased. HPF SETTING (high pass filter adjustment) When you do not want low sounds from the subwoofer output frequency range to play from the front or rear speakers, turn on the HPF (high pass filter). Only frequencies higher than those in the selected range are output from the front or rear speakers. 1 Press M.C. to display the setting mode. 2 Press M.C. to cycle between the following: Cut-off frequency—Slope level 3 Turn M.C. to select the desired setting. Cut-off frequency: OFF—50HZ—63HZ—80HZ —100HZ—125HZ—160HZ—200HZ Slope level: –6— –12 SLA (source level adjustment) SLA (Source level adjustment) lets you adjust the volume level of each source to prevent radical changes in volume when switching between sources. ! Settings are based on the FM volume level, which remains unchanged. ! The MW/LW volume level can also be adjusted with this function. ! When selecting FM as the source, you cannot switch to SLA. 1 Press M.C. to display the setting mode. 2 Turn M.C. to adjust the source volume. Adjustment range: +4 to –4 System menu Important PW SAVE (power saving) is canceled if the vehicle battery is disconnected and will need to be turned back on once the battery is reconnected. When PW SAVE (power saving) is off, depending on connection methods, the unit may continue to draw power from the battery if your vehicle’s ignition doesn’t have an ACC (accessory) position. 1 Press M.C. to display the main menu. 2 Turn M.C. to change the menu option and press to select SYSTEM. 3 Turn M.C. to select the system menu function. Once selected, the following system menu functions can be adjusted. SUB.W CTRL (subwoofer adjustment) 6 En <QRD3143-C> 6 Black plate (7,1) Section Operating this unit LANGUAGE (multi-language) CLOCK SET (setting the clock) 1 Press M.C. to display the setting mode. 2 Press M.C. to select the segment of the clock display you wish to set. Hour—Minute 3 Turn M.C. to adjust the clock. 12H/24H (time notation) Sound from this system is automatically muted or attenuated when a signal from equipment with a mute function is received. 1 Press M.C. to display the setting mode. 2 Turn M.C. to select the desired setting. You can select any one of the options in the following list: ! MUTE – Muting ! 20dB ATT – Attenuation (20dB ATT has a stronger effect than 10dB ATT) ! 10dB ATT – Attenuation PW SAVE (power saving) Switching this function on enables you to reduce the consumption of battery power. ! Turning on the source is the only operation allowed when this function is on. 1 Press M.C. to turn the power save on or off. Switching the dimmer setting 1 Press M.C. to select the desired setting. 12H (12-hour clock)—24H (24-hour clock) You can adjust the brightness of illumination. AUTO PI (auto PI seek) 1 The unit can automatically search for a different station with the same programming, even during preset recall. 1 Press M.C. to turn Auto PI seek on or off. AUX (auxiliary input) Activate this setting when using an auxiliary device connected to this unit. 1 Press M.C. to turn AUX on or off. MUTE MODE (mute mode) Press M.C. to display the main menu. 2 Turn M.C. to display ILLUMI and press to select. 3 Press M.C. to select the desired setting. OFF (off)—ON (on) ! You can also change the dimmer setting by pressing and holding /DIMMER. 3 Turn M.C. to change the menu option and press to select INITIAL. 4 Turn M.C. to select the initial menu function. Once selected, the following initial menu functions can be adjusted. FM STEP (FM tuning step) Normally, the FM tuning step employed by seek tuning is 50 kHz. When AF or TA is on, the tuning step automatically changes to 100 kHz. It may be preferable to set the tuning step to 50 kHz when AF is on. ! The tuning step remains at 50 kHz during manual tuning. 1 Press M.C. to select the FM tuning step. 50 (50 kHz)—100 (100 kHz) 02 SP-P/O MODE (rear output and preout setting) English This unit can display the text information from a compressed audio file even for information embedded in English or Russian. ! If the embedded language and the selected language setting are not the same, text information may not display properly. ! Some characters may not be displayed properly. 1 Turn M.C. to select the desired setting. ENG (English)—РУС (Russian) Operating this unit The rear speaker leads output and the RCA output of this unit can be used to connect a full-range speaker or subwoofer. Select a suitable option for your connection. 1 Press M.C. to display the setting mode. 2 Turn M.C. to select the desired setting. You can select any one of the options in the following list: ! REAR/SUB.W – Select when there is a fullrange speaker connected to the rear speaker leads output and there is a subwoofer connected to the RCA output. ! SUB.W/SUB.W – Select when there is a subwoofer connected directly to the rear speaker leads output without any auxiliary amp and there is a subwoofer connected to the RCA output. ! REAR/REAR – Select when there is a fullrange speaker connected to the rear speaker leads output and the RCA output. If there is a full-range speaker connected to the rear speaker leads output and the RCA output is not used, you may select either REAR/SUB.W or REAR/REAR. System menu 1 Press and hold SRC/OFF until the unit turns off. 2 Press and hold SRC/OFF until the main menu appears in the display. Initial menu 1 Press and hold SRC/OFF until the unit turns off. 2 Press and hold SRC/OFF until the main menu appears in the display. 3 Turn M.C. to change the menu option and press to select SYSTEM. 4 Turn M.C. to select the system menu function. Once selected, the following system menu functions can be adjusted. En <QRD3143-C> 7 7 Black plate (8,1) Section Operating this unit 02 Installation 03 1 Insert the stereo mini plug into the AUX input jack. 2 Press SRC/OFF to select AUX as the source. Selecting the desired text information 1 Press DISP to cycle between the following: ! Source name ! Source name and clock If an unwanted display appears Turn off the unwanted display using the procedures listed below. 1 Press M.C. to display the main menu. 2 Turn M.C. to change the menu option and press to select SYSTEM. 3 Turn M.C. to display DEMO OFF and press to select. 8 4 Turn M.C. to switch to YES. 5 Press M.C. to select. O ACC position STAR Switching the display F N Note AUX cannot be selected unless the auxiliary setting is turned on. For more details, refer to AUX (auxiliary input) on the previous page. Important ! When installing this unit in a vehicle without an ACC (accessory) position on the ignition switch, failure to connect the red cable to the terminal that detects operation of the ignition key may result in battery drain. OF Using an AUX source — Never wire the negative speaker cable directly to ground. — Never band together negative cables of multiple speakers. Connections T For details, refer to System menu on page 6. No ACC position ! Use of this unit in conditions other than the following could result in fire or malfunction. — Vehicles with a 12-volt battery and negative grounding. — Speakers with 50 W (output value) and 4 W to 8 W (impedance value). ! To prevent a short-circuit, overheating or malfunction, be sure to follow the directions below. — Disconnect the negative terminal of the battery before installation. — Secure the wiring with cable clamps or adhesive tape. Wrap adhesive tape around wiring that comes into contact with metal parts to protect the wiring. — Place all cables away from moving parts, such as the shift lever and seat rails. — Place all cables away from hot places, such as near the heater outlet. — Do not connect the yellow cable to the battery by passing it through the hole to the engine compartment. — Cover any disconnected cable connectors with insulating tape. — Do not shorten any cables. — Never cut the insulation of the power cable of this unit in order to share the power with other devices. The current capacity of the cable is limited. — Use a fuse of the rating prescribed. ! When this unit is on, control signals are sent through the blue/white cable. Connect this cable to the system remote control of an external power amp or the vehicle’s auto-antenna relay control terminal (max. 300 mA 12 V DC). If the vehicle is equipped with a glass antenna, connect it to the antenna booster power supply terminal. ! Never connect the blue/white cable to the power terminal of an external power amp. Also, never connect it to the power terminal of the auto antenna. Doing so may result in battery drain or a malfunction. ! The black cable is ground. Ground cables for this unit and other equipment (especially, high-current products such as power amps) must be wired separately. If they are not, an accidental detachment may result in a fire or malfunction. This unit 1 3 1 2 3 4 5 4 2 5 Power cord input Rear output or subwoofer output Antenna input Fuse (10 A) Wired remote input Hard-wired remote control adapter can be connected (sold separately). En <QRD3143-C> 8 Black plate (9,1) Section Installation Installation Power cord 4 5 6 3 5 7 1 4 6 8 a 9 e b c d 1 To power cord input 2 Depending on the kind of vehicle, the function of 3 and 5 may be different. In this case, be sure to connect 4 to 5 and 6 to 3. 3 Yellow Back-up (or accessory) 4 Yellow Connect to the constant 12 V supply terminal. 5 Red Accessory (or back-up) 6 Red Connect to terminal controlled by ignition switch (12 V DC). 7 Connect leads of the same color to each other. 8 Black (chassis ground) Notes ! Change the initial menu of this unit. Refer to SP-P/O MODE (rear output and preout setting) on page 7. The subwoofer output of this unit is monaural. ! When using a subwoofer of 70 W (2 W), be sure to connect the subwoofer to the violet and violet/black leads of this unit. Do not connect anything to the green and green/ black leads. Power amp (sold separately) Perform these connections when using the optional amplifier. 3 1 5 2     ! When installing, to ensure proper heat dispersal when using this unit, make sure you leave ample space behind the rear panel and wrap any loose cables so they are not blocking the vents. English 2 3 9 Blue/white The pin position of the ISO connector will differ depending on the type of vehicle. Connect 9 and b when Pin 5 is an antenna control type. In another type of vehicle, never connect 9 and b. a Blue/white Connect to system control terminal of the power amp (max. 300 mA 12 V DC). b Blue/white Connect to auto-antenna relay control terminal (max. 300 mA 12 V DC). c Yellow/black If you use an equipment with Mute function, wire this lead to the Audio Mute lead on that equipment. If not, keep the Audio Mute lead free of any connections. d Speaker leads White: Front left + White/black: Front left * Gray: Front right + Gray/black: Front right * Green: Rear left + or subwoofer + Green/black: Rear left * or subwoofer * Violet: Rear right + or subwoofer + Violet/black: Rear right * or subwoofer * e ISO connector In some vehicles, the ISO connector may be divided into two. In this case, be sure to connect to both connectors. 03 4 5 1 System remote control Connect to Blue/white cable. 2 Power amp (sold separately) 3 Connect with RCA cables (sold separately) 4 To Rear output or subwoofer output 5 Rear speaker or subwoofer Leave ample 5 cm space 5 cm 5cm cm DIN front/rear mount Installation ! ! ! ! Important Check all connections and systems before final installation. Do not use unauthorized parts as this may cause malfunctions. Consult your dealer if installation requires drilling of holes or other modifications to the vehicle. Do not install this unit where: — it may interfere with operation of the vehicle. — it may cause injury to a passenger as a result of a sudden stop. ! The semiconductor laser will be damaged if it overheats. Install this unit away from hot places such as near the heater outlet. ! Optimum performance is obtained when the unit is installed at an angle of less than 60°. This unit can be properly installed using either front-mount or rear-mount installation. Use commercially available parts when installing. DIN Front-mount 1 Insert the mounting sleeve into the dashboard. For installation in shallow spaces, use the supplied mounting sleeve. If there is enough space, use the mounting sleeve that came with the vehicle. 2 Secure the mounting sleeve by using a screwdriver to bend the metal tabs (90°) into place. 1 60° 2 1 Dashboard En <QRD3143-C> 9 9 Black plate (10,1) Section Installation 03 Additional information 2 Mounting sleeve # Make sure that the unit is installed securely in place. An unstable installation may cause skipping or other malfunctions. DIN Rear-mount 1 Determine the appropriate position where the holes on the bracket and the side of the unit match. 2 Tighten two screws on each side. 3 1 2 1 Tapping screw (5 mm × 8 mm) 2 Mounting bracket 3 Dashboard or console Removing the unit 1 Remove the trim ring. 1 Trim ring 2 Notched tab ! Releasing the front panel allows easier access to the trim ring. 10 ! When reattaching the trim ring, point the side with the notched tab down. 2 Insert the supplied extraction keys into both sides of the unit until they click into place. 3 Pull the unit out of the dashboard. Troubleshooting Symptom Cause Action The display automatically returns to the ordinary display. You did not perform any operation within about 30 seconds. Perform operation again. The repeat play range changes unexpectedly. Depending on Select the repeat the repeat play play range again. range, the selected range may change when another folder or track is being selected or during fast forwarding/reversing. Removing and re-attaching the front panel You can remove the front panel to protect your unit from theft. Press the detach button and push the front panel upward and pull it toward you. For details, refer to Removing the front panel to protect your unit from theft and Re-attaching the front panel on page 3. Error messages A subfolder is Subfolders cannot played not be played back. when FLD (folder repeat) is selected. Select another repeat play range. NO XXXX ap- There is no empears when a bedded text indisplay is formation. changed (NO TITLE, for example). Switch the display or play another track/file. The unit is malfunctioning. There is interference. Move electrical devices that may be causing the interference away from the unit. You are using a device, such as a cellular phone, that transmits electric waves near the unit. When you contact your dealer or your nearest Pioneer Service Center, be sure to note the error message. Common Message Cause Action AMP ERROR Unit fails to operate or speaker connection is incorrect; protective circuit is activated. Check the speaker connection. If the message fails to disappear even after the engine is switched off/on, contact your dealer or an authorized Pioneer Service Station for assistance. Cause Action CD player Message ERROR-07, The disc is dirty. Clean the disc. 11, 12, 17, 30 The disc is Replace the disc. scratched. ERROR-07, 10, 11, 12, 15, 17, 30, A0 There is an elec- Turn the ignition trical or meswitch OFF and chanical error. back ON, or switch to a different source, then back to the CD player. ERROR-15 The inserted disc is blank. Replace the disc. ERROR-23 Unsupported CD format. Replace the disc. En <QRD3143-C> 10 Black plate (11,1) Appendix Additional information Cause Action Sometimes there is a delay between the start of playback and when you start to hear any sound. Wait until the message disappears and you hear sound. The inserted disc does not contain any playable files. Replace the disc. The inserted disc contains DRM protected files. Replace the disc. All the files on the inserted disc are embedded with DRM. Replace the disc. NO AUDIO SKIPPED PROTECT Use only conventional, fully circular discs. Do not use shaped discs. Do not insert anything other than a CD into the CD loading slot. Do not use cracked, chipped, warped, or otherwise damaged discs as they may damage the player. Unfinalized CD-R/RW discs cannot be played back. Do not touch the recorded surface of the discs. Store discs in their cases when not in use. Handling guidelines Discs and player Use only discs that feature either of the following two logos. Do not attach labels, write on or apply chemicals to the surface of the discs. To clean a CD, wipe the disc with a soft cloth outward from the center. Condensation may temporarily impair the player’s performance. Let it rest for about one hour to adjust to a warmer temperature. Also, wipe any damp discs off with a soft cloth. Playback of discs may not be possible because of disc characteristics, disc format, recorded application, playback environment, storage conditions, and so on. Road shocks may interrupt disc playback. When using discs that can be printed on label surfaces, check the instructions and the warnings of the discs. Depending on the discs, inserting and ejecting may not be possible. Using such discs may result in damage to this equipment. Do not attach commercially available labels or other materials to the discs. ! The discs may warp making the disc unplayable. ! The labels may come off during playback and prevent ejection of the discs, which may result in damage to the equipment. DualDiscs DualDiscs are two-sided discs that have a recordable CD for audio on one side and a recordable DVD for video on the other. Since the CD side of DualDiscs is not physically compatible with the general CD standard, it may not be possible to play the CD side with this unit. Frequent loading and ejecting of a DualDisc may result in scratches on the disc. Serious scratches can lead to playback problems on this unit. In some cases, a DualDisc may become stuck in the disc loading slot and will not eject. To prevent this, we recommend you refrain from using DualDisc with this unit. Please refer to the information from the disc manufacturer for more detailed information about DualDiscs. Sampling frequency: 32 kHz, 44.1 kHz, 48 kHz English Message FORMAT READ Additional information Windows Media Audio Professional, Lossless, Voice/DRM Stream/Stream with video: Not compatible MP3 File extension: .mp3 Bit rate: 8 kbps to 320 kbps (CBR), VBR Sampling frequency: 8 kHz to 48 kHz (32 kHz, 44.1 kHz, 48 kHz for emphasis) Compatible ID3 tag version: 1.0, 1.1, 2.2, 2.3, 2.4 (ID3 tag Version 2.x is given priority over Version 1.x.) M3u playlist: Not compatible MP3i (MP3 interactive), mp3 PRO: Not compatible WAV File extension: .wav Quantization bits: 8 and 16 (LPCM), 4 (MS ADPCM) Sampling frequency: 16 kHz to 48 kHz (LPCM), 22.05 kHz and 44.1 kHz (MS ADPCM) Read the precautions for discs before using them. Compressed audio compatibility WMA Use 12-cm discs. Do not use 8-cm discs or an adapter for 8-cm discs. File extension: .wma Bit rate: 48 kbps to 320 kbps (CBR), 48 kbps to 384 kbps (VBR) En <QRD3143-C> 11 11 Black plate (12,1) Appendix Additional information Supplemental information Additional information MP3 Example of a hierarchy 01 02 Only the first 32 characters can be displayed as a file name (including the file extension) or a folder name.   03 Russian text to be displayed on this unit should be encoded in one of the following character sets: ! Unicode (UTF-8, UTF-16) ! A character set other than Unicode that is used in a Windows environment and is set to Russian in the multi-language setting This unit may not operate correctly depending on the application used to encode WMA files. Disc Playable folder hierarchy: up to eight tiers (A practical hierarchy is less than two tiers.) Playable folders: up to 99   04   05 Level 1 Level 2 Level 3 Level 4 : Folder : Compressed audio file 01 to 05: Folder number 1 to 6: Playback sequence Disc Folder selection sequence or other operation may differ depending on the encoding or writing software. Russian character chart D: C D: C D: C D: C D: C Playable files: up to 999 :А :Б :В :Г :Д File system: ISO 9660 Level 1 and 2, Romeo, Joliet : Е, Ё :Ж :З : И, Й :К Multi-session playback: Compatible :Л :М :Н :О :П Packet write data transfer: Not compatible :Р :С :Т :У :Ф :Х :Ц :Ч : Ш, Щ :Ъ :Ы :Ь :Э :Ю :Я Regardless of the length of blank sections between the songs from the original recording, compressed audio discs play with a short pause between songs. D: Display C: Character CAUTION Do not leave discs in any place that is subject to high temperatures. Copyright and trademark iTunes Sequence of audio files The user cannot assign folder numbers and specify playback sequences with this unit. 12 Apple and iTunes are trademarks of Apple Inc., registered in the U.S. and other countries. Supply of this product only conveys a license for private, non-commercial use and does not convey a license nor imply any right to use this product in any commercial (i.e. revenue-generating) real time broadcasting (terrestrial, satellite, cable and/or any other media), broadcasting/ streaming via internet, intranets and/or other networks or in other electronic content distribution systems, such as pay-audio or audio-on-demand applications. An independent license for such use is required. For details, please visit http://www.mp3licensing.com. WMA Windows Media is either a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries. This product includes technology owned by Microsoft Corporation and cannot be used or distributed without a license from Microsoft Licensing, Inc. Specifications General Power source ................... 14.4 V DC (10.8 V to 15.1 V allowable) Grounding system ............ Negative type Maximum current consumption ................................... 10.0 A Dimensions (W × H × D): DIN Chassis .............. 178 mm × 50 mm × 165 mm Nose .................. 188 mm × 58 mm × 16 mm D Chassis .............. 178 mm × 50 mm × 165 mm Nose .................. 170 mm × 46 mm × 16 mm Weight ............................. 1 kg Audio Maximum power output ... 50 W × 4 70 W × 1/2 W (for subwoofer) Continuous power output ................................... 22 W × 4 (50 Hz to 15 000 Hz, 5 % THD, 4 W load, both channels driven) Load impedance .............. 4 W (4 W to 8 W allowable) Preout maximum output level ................................... 2.0 V Loudness contour ............ +10 dB (100 Hz), +6.5 dB (10 kHz) (volume: –30 dB) Equalizer (5-Band Graphic Equalizer): Frequency ................. 80 Hz/250 Hz/800 Hz/ 2.5 kHz/8 kHz Equalization range .... ±12 dB (2 dB step) Subwoofer (mono): Frequency ................. 50 Hz/63 Hz/80 Hz/100 Hz/ 125 Hz/160 Hz/200 Hz Slope ........................ –6 dB/oct, –12 dB/oct Gain ......................... +6 dB to –24 dB Phase ....................... Normal/Reverse CD player System ............................ Compact disc audio system Usable discs .................... Compact disc Signal-to-noise ratio ......... 94 dB (1 kHz) (IEC-A network) En <QRD3143-C> 12 Black plate (13,1) Appendix Additional information English Number of channels ........ 2 (stereo) MP3 decoding format ...... MPEG-1 & 2 Audio Layer 3 WMA decoding format ..... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2 ch audio) (Windows Media Player) WAV signal format ........... Linear PCM & MS ADPCM (Non-compressed) FM tuner Frequency range .............. 87.5 MHz to 108.0 MHz Usable sensitivity ............. 9 dBf (0.8 µV/75 W, mono, S/N: 30 dB) Signal-to-noise ratio ......... 72 dB (IEC-A network) MW tuner Frequency range .............. 531 kHz to 1 602 kHz Usable sensitivity ............. 25 µV (S/N: 20 dB) Signal-to-noise ratio ......... 62 dB (IEC-A network) LW tuner Frequency range .............. 153 kHz to 281 kHz Usable sensitivity ............. 28 µV (S/N: 20 dB) Signal-to-noise ratio ......... 62 dB (IEC-A network) Note Specifications and the design are subject to modifications without notice. En <QRD3143-C> 13 13 Black plate (14,1) Section Avant de commencer 01 Nous vous remercions d’avoir acheté cet appareil PIONEER. Pour garantir une utilisation correcte, lisez bien ce mode d’emploi avant d’utiliser cet appareil. Il est particulièrement important que vous lisiez et respectiez les indications ATTENTION et PRÉCAUTION de ce mode d’emploi. Conservez-le dans un endroit sûr et facilement accessible pour toute consultation ultérieure. Avant de commencer Quelques mots sur cet appareil En cas d’anomalie Les fréquences du syntoniseur de cet appareil sont attribuées pour une utilisation en Europe de l’Ouest, Asie, Moyen Orient, Afrique et Océanie. Son utilisation dans d’autres régions peut se traduire par une réception de mauvaise qualité. La fonction RDS (radio data system) n’est opérationnelle que dans les régions où des signaux RDS sont diffusés pour les stations FM. En cas d’anomalie, veuillez contacter votre revendeur ou le centre d’entretien agréé par PIONEER le plus proche. PRÉCAUTION Cet appareil est un produit laser de Classe 1, classé selon l’article IEC 60825-1:2007 relatif à la Sécurité des produits laser. Si vous souhaitez vous débarrasser de cet appareil, ne le mettez pas à la poubelle avec vos ordures ménagères. Il existe un système de collecte séparé pour les appareils électroniques usagés, qui doivent être récupérés, traités et recyclés conformément à la législation. Dans les états membres de l’UE, en Suisse et en Norvège, les foyers domestiques peuvent rapporter leurs produits électroniques usagés gratuitement à des points de collecte spécifiés ou à un revendeur (sous réserve d’achat d’un produit similaire). Dans les pays qui ne sont pas mentionnés cidessus, veuillez contacter les autorités locales pour vous informer de la méthode correcte de mise au rebut. En agissant ainsi vous assurerez que le produit que vous mettez au rebut est soumis au processus de traitement, de récupération et de recyclage nécessaire et éviterez ainsi les effets négatifs potentiels sur l’environnement et la santé publique. 14 APPAREIL À LASER DE CLASSE 1 PRÉCAUTION ! Ne laissez pas cet appareil entrer en contact avec des liquides. Cela pourrait provoquer une électrocution. Tout contact avec des liquides pourrait également provoquer des dommages, de la fumée et une surchauffe de l’appareil. ! Le Pioneer CarStereo-Pass est utilisable seulement en Allemagne. ! Maintenez le niveau d’écoute à une valeur telle que vous puissiez entendre les sons provenant de l’extérieur. ! Évitez tout contact avec l’humidité. ! Si la batterie est débranchée ou déchargée, le contenu de la mémoire sera effacé. Remarque Les opérations de réglage des fonctions sont validées même si le menu est annulé avant la confirmation des opérations. Fr <QRD3143-C> 14 Black plate (15,1) Section Utilisation de l’appareil Utilisation de l’appareil Appareil central Indicateur 1 2 34 5 6 9 a b Partie c d h (éjection) 8 BAND 2 SRC/OFF 9 (retour)/DIMMER (atténuateur de luminosité) 3 MULTI-CONTROL (M.C.) a c/d b 1/ c Jack d’entrée AUX (jack stéréo 3,5 mm) (liste) 5 DISP Fente de chargement des disques 6 7 2 Section d’informations secondaires 3 TA (bulletins d’informations routières) 4 TP (identification des programmes d’informations routières) Partie 1 4 (liste) à 6/ Touche de retrait de la face avant d 2 3 4 5 2 L’appareil est accordé sur une station TP. La fonction Sound Retriever est activée. 6 LOC L’accord automatique sur une station locale est en service. 7 (répétition de la lecture) La fonction de répétition d’une plage ou d’un dossier est activée. 8 (lecture aléatoire) La lecture aléatoire est activée. Section d’informations principales ! Syntoniseur : gamme et fréquence ! RDS : nom du service de programme, informations PTY et autres informations textuelles ! Lecteur de CD : temps de lecture écoulé et informations textuelles 6 8 7 9 9 La fonction TA est en service. 1 Après avoir installé l’appareil, mettez le contact d’allumage sur ON. SET UP s’affiche. (sound retriever) Indications affichées 1 Les informations secondaires sont affichées. Lorsque vous mettez le contact d’allumage sur ON après l’installation, le menu de configuration s’affiche sur l’écran. Vous pouvez configurer les options de menu cidessous. La fonction liste est utilisée. 5 (égaliseur) a a Menu de configuration 3 Apparaît lorsqu’un niveau inférieur de dossier ou de menu existe. Tournez M.C. pour passer à YES. # Si vous n’effectuez aucune opération dans les 30 secondes environ, le menu de configuration ne s’affichera pas. # Si vous préférez ne pas effectuer la configuration pour l’instant, tournez M.C. pour passer à NO. Appuyez pour sélectionner. Si vous sélectionnez NO, vous ne pouvez pas effectuer de réglage dans le menu de configuration. Appuyez sur M.C. pour sélectionner. 4 Effectuez les procédures suivantes pour configurer le menu. Pour passer à la prochaine option de menu, vous devez confirmer votre sélection. LANGUAGE (multilingue) Cet appareil peut afficher les informations textuelles d’un fichier audio compressé même si elles sont incorporées en anglais ou en russe. ! Si la langue incorporée et la langue sélectionnée sont différentes, les informations textuelles peuvent ne pas s’afficher correctement. ! Certains caractères peuvent ne pas s’afficher correctement. 1 Tournez M.C. pour sélectionner le réglage souhaité. ENG (Anglais)—РУС (Russe) 2 Appuyez sur M.C. pour confirmer la sélection. CLOCK SET (réglage de l’horloge) 1 Tournez M.C. pour régler l’heure. 2 Appuyez sur M.C. pour sélectionner les minutes. 3 Tournez M.C. pour régler les minutes. 4 Appuyez sur M.C. pour confirmer la sélection. FM STEP (incrément d’accord FM) Normalement, l’incrément d’accord FM employé par l’accord automatique est 50 kHz. Quand la fonction AF ou TA est en service, l’incrément d’accord passe automatiquement à 100 kHz. Il peut être préférable de régler l’incrément d’accord à 50 kHz quand la fonction AF est en service. ! Pendant l’accord manuel, l’incrément d’accord est maintenu à 50 kHz. 1 Tournez M.C. pour choisir l’incrément d’accord FM. 50 (50 kHz)—100 (100 kHz) 2 Appuyez sur M.C. pour confirmer la sélection. QUIT s’affiche. Français 7 8 1 État 02 5 Pour terminer la configuration, tournez M.C. pour sélectionner YES. # Si vous souhaitez modifier à nouveau le réglage, tournez M.C. pour passer à NO. Appuyez pour sélectionner. 6 Appuyez sur M.C. pour sélectionner. Remarques ! Vous pouvez configurer les options de menu à partir du menu système. Pour des détails sur les réglages, reportez-vous à la page 19, Menu système. ! Vous pouvez annuler le menu de configuration en appuyant sur SRC/OFF. Opérations de base Important ! Lorsque vous enlevez ou remontez la face avant, manipulez-la doucement. Fr <QRD3143-C> 15 15 Black plate (16,1) Section Utilisation de l’appareil 02 ! Évitez de heurter la face avant. ! Conservez la face avant à l’abri des températures élevées et de la lumière directe du soleil. ! Pour éviter d’endommager le périphérique ou l’intérieur du véhicule, retirez tous les câbles et périphériques connectés à la face avant, avant d’enlever cette dernière. Retrait de la face avant pour protéger l’appareil contre le vol 1 Appuyez sur la touche de retrait pour libérer la face avant. 2 Poussez la face avant vers le haut (M), puis tirez-la vers vous (N). Utilisation de l’appareil Mise en service de l’appareil 1 Appuyez sur SRC/OFF pour mettre en service l’appareil. Mise hors service de l’appareil 1 Maintenez la pression sur SRC/OFF jusqu’à ce que l’appareil soit mis hors tension. Choix d’une source 1 Appuyez sur SRC/OFF pour parcourir les options disponibles : TUNER (syntoniseur)—CD (lecteur de CD)— AUX (AUX) Réglage du volume 1 Tournez M.C. pour régler le volume. PRÉCAUTION Pour des raisons de sécurité, garez votre véhicule pour retirer la face avant. 3 Conservez toujours la face avant dans un boîtier de protection lorsqu’elle est détachée. Remontage de la face avant 1 Faites glisser la face avant vers la gauche. Assurez-vous d’insérer les encoches sur le côté gauche de l’appareil central dans les fentes du panneau de commande. 2 Appuyez sur le côté droit de la face avant jusqu’à ce qu’elle soit bien en place. Si vous ne pouvez pas monter la face avant sur l’appareil central, vérifiez que la face avant est correctement placée sur l’appareil central. Forcer la face avant en position risque de l’endommager ou d’endommager l’appareil central. 16 Remarque Si le fil bleu/blanc de l’appareil est relié à la prise de commande du relais de l’antenne motorisée du véhicule, celle-ci se déploie lorsque la source est mise en service. Pour rétracter l’antenne, mettez la source hors service. Opérations de menu fréquemment utilisées Retour à l’affichage précédent Retour à la liste précédente (le dossier de niveau immédiatement supérieur) 1 Appuyez sur /DIMMER. Retour à l’affichage ordinaire Annulation du menu principal 1 Appuyez sur BAND. Retour à l’affichage ordinaire à partir de la liste 1 Appuyez sur BAND. Syntoniseur Opérations de base Enregistrement et rappel des stations pour chaque gamme Utilisation des touches de présélection Sélection d’une gamme 1 Appuyez sur BAND jusqu’à ce que la gamme souhaitée, FM1, FM2, FM3 en FM ou MW/LW (PO/GO), soit affichée. Changement de fréquence en mémoire 1 Appuyez sur c ou d. ! Sélectionnez PCH (canal présélectionné) sous SEEK pour utiliser cette fonction. Pour des détails sur les réglages, reportez-vous à la page suivante, SEEK (réglage de la touche droite/gauche). Accord manuel (pas à pas) 1 Appuyez sur c ou d. ! Sélectionnez MAN (accord manuel) sous SEEK pour utiliser cette fonction. Pour des détails sur les réglages, reportez-vous à la page suivante, SEEK (réglage de la touche droite/gauche). Recherche 1 Appuyez de manière prolongée sur c ou d, puis relâchez. Vous pouvez annuler l’accord automatique en appuyant brièvement sur c ou d. Lorsque vous appuyez de manière prolongée sur c ou d, vous pouvez sauter des stations. L’accord automatique démarre dès que vous relâchez c ou d. Remarque La fonction AF (recherche des autres fréquences possibles) de cet appareil peut être mise en service ou hors service. La fonction AF doit être hors service pendant une opération d’accord normal (reportez-vous à la page suivante, AF (recherche des autres fréquences possibles)). 1 Lorsque se présente une station que vous souhaitez mettre en mémoire, appuyez de manière prolongée sur l’une des touches de présélection (1/ à 6/ ) jusqu’à ce que le numéro de la présélection cesse de clignoter. 2 Appuyez sur l’une des touches de présélection (1/ à 6/ ) pour sélectionner la station souhaitée. Changement de l’affichage Sélection des informations textuelles souhaitées 1 Appuyez sur DISP pour parcourir les options disponibles : ! FREQUENCY (nom du service de programme ou fréquence) ! BRDCST INFO (nom du service de programme/informations PTY) ! CLOCK (nom de la source et horloge) Remarques ! Si le nom du service de programme ne peut pas être acquis dans FREQUENCY, la fréquence d’émission s’affiche alors. Si le nom du service de programme est détecté, celuici s’affiche. ! Les informations textuelles BRDCST INFO changent automatiquement. ! En fonction de la gamme sélectionnée, les informations textuelles peuvent être différentes. ! Les informations textuelles pouvant être modifiées dépendent de la région. Utilisation des fonctions PTY Vous pouvez rechercher une station à l’aide de son code PTY (type de programme). Fr <QRD3143-C> 16 Black plate (17,1) Section Utilisation de l’appareil Liste des codes PTY L. CLASS (Musique classique légère), CLASSIC (Musique classique) OTHERS (autres) EDUCATE (Éducation), DRAMA (Drame), CULTURE (Culture), SCIENCE (Science), VARIED (Programmes variés), CHILDREN (Émissions destinées aux enfants), SOCIAL (Sujets de société), RELIGION (Religion), PHONE IN (Programmes à ligne ouverte), TOURING (Voyages), LEISURE (Loisirs), DOCUMENT (Documentaires) Réglages des fonctions 1 Appuyez sur M.C. pour afficher le menu principal. 2 Tournez M.C. pour changer l’option de menu et appuyez pour sélectionner FUNCTION. 3 Tournez M.C. pour sélectionner la fonction. Une fois sélectionnées, les fonctions suivantes peuvent être ajustées. # Si la gamme MW/LW (PO/GO) est sélectionnée, seuls BSM, LOCAL et SEEK sont disponibles. BSM (mémoire des meilleures stations) NEWS/INFO (actualités et informations) NEWS (Bulletin d’informations), AFFAIRS (Actualités), INFO (Informations), SPORT (Sports), WEATHER (Météo), FINANCE (Finance) POPULAR (populaire) POP MUS (Musique populaire), ROCK MUS (Rock), EASY MUS (Musique légère), OTH MUS (Autre musique), JAZZ (Jazz), COUNTRY (Country), NAT MUS (Musique nationale), OLDIES (Musique du bon vieux temps), FOLK MUS (Folk) La fonction BSM (mémoire des meilleures stations) mémorise automatiquement les six stations les plus fortes dans l’ordre de la force du signal. 1 Appuyez sur M.C. pour mettre la fonction BSM en service. Pour annuler, appuyez à nouveau sur M.C. REGION (stations régionales) Quand la fonction AF est utilisée, la fonction de recherche des stations régionales limite la sélection aux stations qui diffusent des programmes régionaux. 1 Appuyez sur M.C. pour mettre la fonction de recherche des stations régionales en service ou hors service. LOCAL (accord automatique sur une station locale) L’accord automatique sur une station locale ne s’intéresse qu’aux stations de radio dont le signal reçu est suffisamment puissant pour garantir une réception de bonne qualité. 1 Appuyez sur M.C. pour sélectionner le réglage souhaité. FM : OFF—LV1—LV2—LV3—LV4 MW/LW (PO/GO) : OFF—LV1—LV2 La valeur la plus élevée permet la réception des seules stations très puissantes ; les autres valeurs autorisent la réception de stations moins puissantes. TA (attente de bulletins d’informations routières) 1 Appuyez sur M.C. pour mettre en service ou hors service l’attente d’un bulletin d’informations routières. 02 SEEK (réglage de la touche droite/gauche) Vous pouvez assigner une fonction aux touches droite et gauche de l’appareil. Sélectionnez MAN (accord manuel) pour effectuer un accord de fréquence manuellement ou sélectionnez PCH (canaux présélectionnés) pour changer de canal présélectionné. 1 Appuyez sur M.C. pour sélectionner MAN ou PCH. CD/CD-R/CD-RW Opérations de base Lecture d’un CD/CD-R/CD-RW 1 Introduisez un disque, l’étiquette vers le haut, dans le logement de chargement des disques. Éjection d’un CD/CD-R/CD-RW 1 Appuyez sur h. Sélection d’un dossier 1 Appuyez sur 1/ ou 2/ . Sélection d’une plage 1 Appuyez sur c ou d. 1 Appuyez sur M.C. pour mettre la fonction AF en service ou hors service. Avance ou retour rapide 1 Appuyez de manière prolongée sur c ou d. ! Lors de la lecture d’un disque d’audio compressé, aucun son n’est émis pendant l’avance ou le retour rapide. NEWS (interruption pour réception d’un bulletin d’informations) Retour au dossier racine 1 Appuyez sur BAND de façon prolongée. 1 Appuyez sur M.C. pour mettre la fonction NEWS (bulletin d’informations) en service ou hors service. Commutation entre les modes audio compressé et CD-DA 1 Appuyez sur BAND. AF (recherche des autres fréquences possibles) Français Recherche d’une station RDS en utilisant le code PTY Vous pouvez rechercher une station qui diffuse un type général de programme mentionné dans la liste de la section suivante. Reportez-vous à cette page. (liste). 1 Appuyez sur 2 Tournez M.C. pour sélectionner le type de programme. NEWS/INFO—POPULAR—CLASSICS— OTHERS 3 Appuyez sur M.C. pour lancer la recherche. Cet appareil recherche une station qui diffuse ce type de programme. Quand une station est trouvée, son nom de service de programme est affiché. ! Appuyez à nouveau sur M.C. pour abandonner la recherche. ! Le type de l’émission captée peut différer de celui indiqué par le code PTY transmis. ! Si aucune station ne diffuse d’émission du type choisi, l’indication NOT FOUND s’affiche pendant environ deux secondes puis le syntoniseur s’accorde sur la fréquence d’origine. Utilisation de l’appareil CLASSICS (classique) Fr <QRD3143-C> 17 17 Black plate (18,1) Section Utilisation de l’appareil 02 Changement de l’affichage Sélection des informations textuelles souhaitées 1 Appuyez sur DISP pour parcourir les options disponibles : CD-DA ! ELAPSED TIME (numéro de plage et temps de lecture) ! CLOCK (nom de la source et horloge) ! SPEANA (analyseur de spectre) CD-TEXT ! TRACK INFO (titre de la plage/interprète de la plage/titre du disque) ! ELAPSED TIME (numéro de plage et temps de lecture) ! CLOCK (nom de la source et horloge) ! SPEANA (analyseur de spectre) MP3/WMA/WAV ! TRACK INFO (titre de la plage/nom de l’interprète/nom de l’album) ! FILE INFO (nom du fichier/nom du dossier) ! ELAPSED TIME (numéro de plage et temps de lecture) ! CLOCK (nom de la source et horloge) ! SPEANA (analyseur de spectre) Remarques ! Les informations textuelles TRACK INFO et FILE INFO changent automatiquement. ! Selon la version de iTunes utilisée pour enregistrer les fichiers MP3 sur un disque ou les types de fichiers média, des informations textuelles incompatibles enregistrées dans le fichier audio peuvent ne pas s’afficher correctement. ! Les informations textuelles pouvant être modifiées dépendent du média. Sélection et lecture des fichiers/ plages à partir de la liste des noms 1 Appuyez sur pour passer en mode liste des noms de fichiers/plages. 18 Utilisation de l’appareil 2 Utilisez M.C. pour sélectionner le nom de fichier (ou nom de dossier) souhaité. Sélection d’un fichier ou d’un dossier 1 Tournez M.C. Lecture 1 Lorsqu’un fichier ou une plage est sélectionné(e), appuyez sur M.C. Affichage d’une liste des fichiers (ou des dossiers) dans le dossier sélectionné 1 Quand un dossier est sélectionné, appuyez sur M.C. Lecture d’une plage musicale dans le dossier sélectionné 1 Quand un dossier est sélectionné, appuyez de manière prolongée sur M.C. Opérations à l’aide de touches spéciales Sélection d’une étendue de répétition de lecture pour parcourir les options 1 Appuyez sur 6/ disponibles : ! ALL – Répétition de toutes les plages ! ONE – Répétition de la plage en cours de lecture ! FLD – Répétition du dossier en cours de lecture Lecture des plages dans un ordre aléatoire pour activer ou désactiver 1 Appuyez sur 5/ la lecture aléatoire. Les plages d’une étendue de répétition sélectionnée sont lues dans un ordre aléatoire. ! Pour changer de plage musicale pendant une lecture aléatoire, appuyez sur d pour passer à la plage suivante. Appuyez sur c pour redémarrer la lecture de la plage en cours au début de la plage musicale. Pause de la lecture 1 Appuyez sur 4/PAUSE pour mettre en pause ou reprendre la lecture. Amélioration de l’audio compressé et restauration d’un son riche (sound retriever (correcteur de son compressé)) 1 Appuyez sur 3/S.Rtrv pour parcourir les options disponibles : 1—2—OFF (hors service) 1 est efficace pour les faibles taux de compression et 2 est efficace pour les taux de compression élevés. Réglages des fonctions 1 Appuyez sur M.C. pour afficher le menu principal. 2 Tournez M.C. pour changer l’option de menu et appuyez pour sélectionner FUNCTION. Une fois sélectionnée, la fonction ci-dessous peut être ajustée. S.RTRV (sound retriever) Améliore automatiquement l’audio compressé et restaure un son riche. 1 Appuyez sur M.C. pour sélectionner le réglage souhaité. Pour les détails, reportez-vous à cette page, Amélioration de l’audio compressé et restauration d’un son riche (sound retriever (correcteur de son compressé)). 3 Tournez M.C. pour sélectionner la fonction audio. Une fois sélectionnées, les fonctions audio suivantes peuvent être ajustées. ! FADER n’est pas disponible lorsque SUB.W/SUB.W est sélectionné dans SP-P/O MODE. Pour les détails, reportez-vous à la page 20, SP-P/O MODE (réglage de la sortie arrière et du préamp). ! SUB.W, SUB.W CTRL et HPF SETTING ne sont pas disponibles lorsque REAR/REAR est sélectionné dans SP-P/O MODE. Pour les détails, reportez-vous à la page 20, SP-P/O MODE (réglage de la sortie arrière et du préamp). ! SUB.W CTRL et HPF SETTING ne sont pas disponibles lorsque SUB.W est sélectionné dans OFF. Pour les détails, reportez-vous à la page suivante, SUB.W (réglage en service/ hors service du haut-parleur d’extrêmes graves). FADER (réglage de l’équilibre avant-arrière) 1 Appuyez sur M.C. pour afficher le mode de réglage. 2 Tournez M.C. pour régler l’équilibre sonore entre les haut-parleurs avant et arrière. BALANCE (réglage d’équilibre sonore) 1 Appuyez sur M.C. pour afficher le mode de réglage. 2 Tournez M.C. pour régler l’équilibre sonore entre les haut-parleurs gauche/droite. EQ SETTING (rappel de l’égaliseur) Réglages sonores 1 Appuyez sur M.C. pour afficher le menu principal. 2 Tournez M.C. pour changer l’option de menu et appuyez pour sélectionner AUDIO. Fr <QRD3143-C> 18 Black plate (19,1) Section Utilisation de l’appareil LOUDNESS (correction physiologique) La correction physiologique a pour objet d’accentuer les hautes et les basses fréquences à bas niveaux d’écoute. 1 Appuyez sur M.C. pour sélectionner le réglage souhaité. OFF (hors service)—LOW (faible)—MID (moyen)—HI (élevé) Cet appareil est équipé d’une sortie haut-parleur d’extrêmes graves qui peut être mise en service ou hors service. 1 Appuyez sur M.C. pour sélectionner le réglage souhaité. NOR (phase normale) — REV (phase inversée) — OFF (haut-parleur d’extrêmes graves désactivé) SUB.W CTRL (réglage du haut-parleur d’extrêmes graves) Seules les fréquences inférieures à celles de la plage sélectionnée sont produites par le haut-parleur d’extrêmes graves. 1 Appuyez sur M.C. pour afficher le mode de réglage. 2 Appuyez sur M.C. pour parcourir les options disponibles : Fréquence de coupure—Niveau de sortie—Niveau de pente Les débits pouvant être réglés clignotent. 3 Tournez M.C. pour sélectionner le réglage souhaité. Fréquence de coupure : 50HZ—63HZ—80HZ —100HZ—125HZ—160HZ—200HZ Niveau de sortie : –24 à +6 Niveau de pente : –6— –12 BASS BOOST (accentuation des graves) 1 Appuyez sur M.C. pour afficher le mode de réglage. 2 Tournez M.C. pour sélectionner le niveau désiré. 0 à +6 sont les valeurs affichées tandis que le niveau augmente ou diminue. HPF SETTING (réglage du filtre passe-haut) Quand vous ne voulez pas que les sons graves de la gamme de fréquence de la sortie haut-parleur d’extrêmes graves soient émis par les haut-parleurs avant ou arrière, mettez le filtre passe-haut (HPF) en service. Seules les fréquences supérieures à celles de la plage sélectionnée sont émises par les haut-parleurs avant ou arrière. 1 Appuyez sur M.C. pour afficher le mode de réglage. 2 Appuyez sur M.C. pour parcourir les options disponibles : Fréquence de coupure—Niveau de pente 3 Tournez M.C. pour sélectionner le réglage souhaité. Fréquence de coupure : OFF—50HZ—63HZ— 80HZ—100HZ—125HZ—160HZ—200HZ Niveau de pente : –6— –12 02 Menu système Important La fonction PW SAVE (économie d’énergie) est annulée si la batterie du véhicule est déconnectée et devra être réactivée une fois la batterie reconnectée. Quand PW SAVE est hors service, il est possible que selon la méthode de connexion utilisée l’appareil continue à consommer du courant de la batterie si le commutateur de contact de votre véhicule ne possède pas de position ACC (accessoire). Français 1 Appuyez sur M.C. pour afficher le mode de réglage. 2 Tournez M.C. pour sélectionner l’égaliseur. POWERFUL—NATURAL—VOCAL—CUSTOM1—CUSTOM2—FLAT—SUPER BASS La bande et le niveau de l’égalisateur peuvent être personnalisés lorsque CUSTOM1 ou CUSTOM2 est sélectionné. Si CUSTOM1 ou CUSTOM2 est sélectionné, suivez les procédures décrites ci-dessous. Si d’autres options sont sélectionnées, appuyez sur M.C. pour revenir à l’affichage précédent. ! CUSTOM1 peut être réglé séparément pour chaque source. ! CUSTOM2 est un réglage partagé et commun à toutes les sources. 3 Appuyez sur M.C. pour afficher le mode de réglage. 4 Appuyez sur M.C. pour parcourir les options disponibles : Bande de l’égaliseur—Niveau de l’égaliseur 5 Tournez M.C. pour sélectionner le réglage souhaité. Bande de l’égaliseur : 80HZ—250HZ—800HZ —2.5KHZ—8KHZ Niveau de l’égaliseur : +6 à –6 ! Vous pouvez également changer l’égaliseur en . appuyant de manière répétée sur Utilisation de l’appareil 1 Appuyez sur M.C. pour afficher le menu principal. 2 Tournez M.C. pour changer l’option de menu et appuyez pour sélectionner SYSTEM. SLA (réglage du niveau de la source) La fonction SLA (réglage du niveau de la source) permet d’ajuster les niveaux sonores de chaque source afin d’éviter que ne se produisent de fortes variations d’amplitude sonore lorsque vous passez d’une source à l’autre. ! Les réglages sont basés sur le niveau du volume FM qui lui, demeure inchangé. ! Le niveau du volume MW/LW (PO/GO) peut également être réglé avec cette fonction. ! Si FM a été choisie comme source, vous ne pouvez pas afficher la fonction SLA. 1 Appuyez sur M.C. pour afficher le mode de réglage. 2 Tournez M.C. pour régler le volume de la source. Plage de réglage : +4 à –4 3 Tournez M.C. pour sélectionner la fonction du menu système. Une fois sélectionnées, les fonctions du menu système suivantes peuvent être ajustées. LANGUAGE (multilingue) Cet appareil peut afficher les informations textuelles d’un fichier audio compressé même si elles sont incorporées en anglais ou en russe. ! Si la langue incorporée et la langue sélectionnée sont différentes, les informations textuelles peuvent ne pas s’afficher correctement. ! Certains caractères peuvent ne pas s’afficher correctement. 1 Tournez M.C. pour sélectionner le réglage souhaité. ENG (Anglais)—РУС (Russe) CLOCK SET (réglage de l’horloge) SUB.W (réglage en service/hors service du hautparleur d’extrêmes graves) Fr <QRD3143-C> 19 19 Black plate (20,1) Section Utilisation de l’appareil 02 Utilisation de l’appareil 1 Appuyez sur M.C. pour sélectionner le réglage souhaité. 12H (horloge 12 heures)—24H (horloge 24 heures) Le son émis par l’appareil est automatiquement coupé ou atténué quand un signal en provenance d’un équipement possédant la fonction silencieux est reçu. 1 Appuyez sur M.C. pour afficher le mode de réglage. 2 Tournez M.C. pour sélectionner le réglage souhaité. Vous pouvez sélectionner l’une des options de la liste suivante : ! MUTE – Silencieux ! 20dB ATT – Atténuation (20dB ATT a un effet plus fort que 10dB ATT) ! 10dB ATT – Atténuation AUTO PI (recherche automatique PI) PW SAVE (économie d’énergie) L’appareil peut rechercher automatiquement une autre station avec le même type de programme, y compris si l’accord a été obtenu par le rappel d’une fréquence en mémoire. 1 Appuyez sur M.C. pour mettre en service ou hors service la recherche automatique PI. Activer cette fonction vous permet de réduire la consommation de la batterie. ! La mise en service de la source est la seule opération permise quand cette fonction est en service. 1 Appuyez sur M.C. pour mettre l’économie d’énergie en service ou hors service. 1 Appuyez sur M.C. pour afficher le mode de réglage. 2 Appuyez sur M.C. pour sélectionner le segment de l’affichage de l’horloge que vous souhaitez régler. Heure—Minute 3 Tournez M.C. pour régler l’horloge. 12H/24H (notation temporelle) AUX (entrée auxiliaire) Activez ce réglage lorsque vous utilisez un appareil auxiliaire connecté à cet appareil. 1 Appuyez sur M.C. pour mettre AUX en service ou hors service. Mise en service ou hors service de l’atténuateur de luminosité MUTE MODE (mode sourdine) Vous pouvez régler la luminosité d’éclairage. 1 Appuyez sur M.C. pour afficher le menu principal. 2 Tournez M.C. pour afficher ILLUMI, puis appuyez pour sélectionner. 3 Appuyez sur M.C. pour sélectionner le réglage souhaité. OFF (hors service)—ON (en service) ! Vous pouvez également changer le réglage de l’atténuateur de luminosité en appuyant /DIMMER. de façon prolongée sur 20 Menu initial 1 Maintenez la pression sur SRC/OFF jusqu’à ce que l’appareil soit mis hors tension. 2 Appuyez de façon prolongée sur SRC/ OFF jusqu’à ce que le menu principal apparaisse sur l’afficheur. 3 Tournez M.C. pour changer l’option de menu et appuyez pour sélectionner INITIAL. 4 Tournez M.C. pour sélectionner la fonction du menu initial. Une fois sélectionnées, les fonctions du menu initial suivantes peuvent être ajustées. FM STEP (incrément d’accord FM) Normalement, l’incrément d’accord FM employé par l’accord automatique est 50 kHz. Quand la fonction AF ou TA est en service, l’incrément d’accord passe automatiquement à 100 kHz. Il peut être préférable de régler l’incrément d’accord à 50 kHz quand la fonction AF est en service. ! Pendant l’accord manuel, l’incrément d’accord est maintenu à 50 kHz. 1 Appuyez sur M.C. pour choisir l’incrément d’accord FM. 50 (50 kHz)—100 (100 kHz) SP-P/O MODE (réglage de la sortie arrière et du préamp) La sortie des bornes du haut-parleur arrière et la sortie RCA de cet appareil peuvent être utilisées pour connecter un haut-parleur pleine gamme ou un haut-parleur d’extrêmes graves. Sélectionnez l’option appropriée à votre connexion. 1 Appuyez sur M.C. pour afficher le mode de réglage. 2 Tournez M.C. pour sélectionner le réglage souhaité. Vous pouvez sélectionner l’une des options de la liste suivante : ! REAR/SUB.W – Sélectionnez cette option lorsqu’un haut-parleur pleine gamme est connecté aux bornes du haut-parleur arrière et qu’un haut-parleur d’extrêmes graves est connecté à la sortie RCA. ! SUB.W/SUB.W – Sélectionnez cette option lorsqu’un haut-parleur d’extrêmes graves est connecté directement aux bornes du haut-parleur arrière sans amplificateur auxiliaire et qu’un haut-parleur d’extrêmes graves est connecté à la sortie RCA. ! REAR/REAR – Sélectionnez cette option lorsqu’un haut-parleur pleine gamme est connecté aux bornes du haut-parleur arrière et à la sortie RCA. Si un haut-parleur pleine gamme est connecté à la sortie des bornes du hautparleur arrière et que la sortie RCA n’est pas utilisée, vous pouvez sélectionner REAR/SUB.W ou REAR/REAR. Menu système 1 Maintenez la pression sur SRC/OFF jusqu’à ce que l’appareil soit mis hors tension. 2 Appuyez de façon prolongée sur SRC/ OFF jusqu’à ce que le menu principal apparaisse sur l’afficheur. Fr <QRD3143-C> 20 Black plate (21,1) Section Utilisation de l’appareil Installation 02 03 2 Tournez M.C. pour changer l’option de menu et appuyez pour sélectionner SYSTEM. 4 Tournez M.C. pour sélectionner la fonction du menu système. Une fois sélectionnées, les fonctions du menu système suivantes peuvent être ajustées. Pour les détails, reportez-vous à la page 19, Menu système. 3 Tournez M.C. pour afficher DEMO OFF, puis appuyez pour sélectionner. 4 Tournez M.C. pour passer à YES. 5 Appuyez sur M.C. pour sélectionner. Connexions Important ! Lors de l’installation de cet appareil dans un véhicule sans position ACC (accessoire) sur le contact d’allumage, ne pas connecter le câble rouge à la borne qui détecte l’utilisation de la clé de contact peut entraîner le déchargement de la batterie. OF F O N T 1 Insérez la mini prise stéréo dans le jack d’entrée AUX. 2 Appuyez sur SRC/OFF pour choisir AUX comme source. Remarque Vous ne pouvez pas sélectionner AUX à moins que le réglage auxiliaire soit activé. Pour plus de détails, reportez-vous à la page précédente, AUX (entrée auxiliaire). Changement de l’affichage Sélection des informations textuelles souhaitées 1 Appuyez sur DISP pour parcourir les options disponibles : ! Nom de la source ! Nom de la source et horloge Si un écran non souhaité s’affiche Mettez l’écran non souhaité hors service à l’aide des procédures répertoriées ci-dessous. 1 Appuyez sur M.C. pour afficher le menu principal. Avec position ACC STAR Utilisation d’une source AUX Sans position ACC ! L’utilisation de cet appareil dans des conditions autres que les conditions suivantes pourrait provoquer un incendie ou un mauvais fonctionnement. — Véhicules avec une batterie 12 volts et mise à la masse du négatif. — Haut-parleurs avec une puissance de sortie de 50 W et une impédance de 4 W à 8 W. ! Pour éviter un court-circuit, une surchauffe ou un dysfonctionnement, assurez-vous de respecter les instructions suivantes. — Déconnectez la borne négative de la batterie avant l’installation. — Fixez le câblage avec des serre-fils ou de la bande adhésive. Pour protéger le câblage, enroulez dans du ruban adhésif les parties du câblage en contact avec des pièces en métal. — Placez les câbles à l’écart de toutes les parties mobiles, telles que le levier de vitesse et les rails des sièges. — Placez les câbles à l’écart de tous les endroits chauds, par exemple les sorties de chauffage. — Ne reliez pas le câble jaune à la batterie à travers le trou dans le compartiment moteur. — Recouvrez tous les connecteurs de câbles qui ne sont pas connectés avec du ruban adhésif isolant. — Ne raccourcissez pas les câbles. — Ne coupez jamais l’isolation du câble d’alimentation de cet appareil pour partager l’alimentation avec d’autres appareils. La capacité en courant du câble est limitée. — Utilisez un fusible correspondant aux caractéristiques spécifiées. — Ne câblez jamais le câble négatif du haut-parleur directement à la masse. — Ne réunissez jamais ensemble les câbles négatifs de plusieurs haut-parleurs. ! Lorsque cet appareil est sous tension, les signaux de commande sont transmis via le câble bleu/blanc. Connectez ce câble à la télécommande du système d’un amplificateur de puissance externe ou à la borne de commande du relais de l’antenne motorisée du véhicule (max. 300 mA 12 V CC). Si le véhicule est équipé d’une antenne intégrée à la lunette arrière, connectez-le à la borne d’alimentation de l’amplificateur d’antenne. ! Ne reliez jamais le câble bleu/blanc à la borne d’alimentation d’un amplificateur de puissance externe. De même, ne le reliez pas à la borne d’alimentation de l’antenne motorisée. Dans le cas contraire, il peut en résulter un déchargement de la batterie ou un dysfonctionnement. ! Le câble noir est la masse. Les câbles de terre de cet appareil et d’autres produits (particulièrement les produits avec des courants élevés tels que l’amplificateur de puissance) doivent être câblés séparément. Dans le cas contraire, ils peuvent se détacher accidentellement et provoquer un incendie ou un dysfonctionnement. Français 3 Tournez M.C. pour changer l’option de menu et appuyez pour sélectionner SYSTEM. Cet appareil 1 3 4 2 5 Fr <QRD3143-C> 21 21 Black plate (22,1) Section Installation 03 Installation 1 Entrée cordon d’alimentation 2 Sortie arrière ou haut-parleur d’extrêmes graves 3 Entrée antenne 4 Fusible (10 A) 5 Entrée télécommande câblée Un adaptateur de télécommande câblée (vendu séparément) peut être connecté. Cordon d’alimentation 2 7 3 4 5 6 3 4 5 6 1 8 a 9 e b c d 1 Vers l’entrée cordon d’alimentation 2 Selon le type de véhicule, 3 et 5 peuvent avoir une fonction différente. Dans ce cas, assurez-vous de connecter 4 à 5 et 6 à 3. 3 Jaune Alimentation de secours (ou accessoire) 4 Jaune Connectez à la borne d’alimentation 12 V permanente. 5 Rouge Accessoire (ou alimentation de secours) 6 Rouge Connectez à la borne contrôlée par le contact d’allumage (12 V CC). 22 7 Connectez les fils de même couleur ensemble. 8 Noir (masse du châssis) 9 Bleu/blanc La position des broches du connecteur ISO est différente selon le type de véhicule. Connectez 9 et b lorsque la broche 5 est de type commande de l’antenne. Dans un type différent de véhicule, ne connectez jamais 9 et b. a Bleu/blanc Connectez à la borne de commande du système de l’amplificateur de puissance (max. 300 mA 12 V CC). b Bleu/blanc Connectez à la borne de commande du relais de l’antenne motorisée (max. 300 mA 12 V CC). c Jaune/noir Si vous utilisez un équipement avec la fonction Coupure du son, câblez ce fil au fil Coupure Audio de cet équipement. Sinon, ne connectez rien au fil Coupure Audio. d Fils des haut-parleurs Blanc : Avant gauche + Blanc/noir : Avant gauche * Gris : Avant droite + Gris/noir : Avant droite * Vert : Arrière gauche + ou haut-parleur d’extrêmes graves + Vert/noir : Arrière gauche * ou haut-parleur d’extrêmes graves * Violet : Arrière droite + ou haut-parleur d’extrêmes graves + Violet/noir : Arrière droite * ou haut-parleur d’extrêmes graves * e Connecteur ISO Dans certains véhicules, il est possible que le connecteur ISO soit divisé en deux. Dans ce cas, assurez-vous de connecter les deux connecteurs. Remarques ! Changez le menu initial de cet appareil. Reportez-vous à la page 20, SP-P/O MODE (réglage de la sortie arrière et du préamp). La sortie haut-parleur d’extrêmes graves de cet appareil est monaurale. ! Lors de l’utilisation d’un haut-parleur d’extrêmes graves de 70 W (2 W), assurez-vous de connecter le haut-parleur d’extrêmes graves aux fils violet et violet/noir de cet appareil. Ne connectez aucun périphérique aux fils vert et vert/noir. Amplificateur de puissance (vendu séparément) ! Consultez votre revendeur si l’installation nécessite le perçage de trous ou d’autres modifications du véhicule. ! N’installez pas cet appareil là où : — il peut interférer avec l’utilisation du véhicule. — il peut blesser un passager en cas d’arrêt soudain du véhicule. ! Le laser à semi-conducteur sera endommagé s’il devient trop chaud. Installez cet appareil à l’écart de tous les endroits chauds, par exemple les sorties de chauffage. ! Des performances optimales sont obtenues quand l’appareil est installé à un angle inférieur à 60°. 60° Réalisez ces connexions lors de l’utilisation d’un amplificateur optionnel. 3 1 5 2     4 5 1 Télécommande du système Connectez au câble bleu/blanc. 2 Amplificateur de puissance (vendu séparément) 3 Connectez avec des câbles RCA (vendus séparément) 4 Vers la sortie arrière ou la sortie du haut-parleur d’extrêmes graves 5 Haut-parleur arrière ou haut-parleur d’extrêmes graves Installation Important ! Vérifiez toutes les connexions et tous les systèmes avant l’installation finale. ! N’utilisez pas de pièces non autorisées car il peut en résulter des dysfonctionnements. ! Lors de l’installation, pour assurer une dispersion correcte de la chaleur quand cet appareil est utilisé, assurez-vous de laisser un espace important derrière la face arrière et enroulez les câbles volants de façon qu’ils ne bloquent pas les orifices d’aération. Laissez suffisamment 5 cm d’espace 5 cm 5cm cm Montage avant/arrière DIN Cet appareil peut être installé correctement soit en montage frontal ou en montage arrière. Utilisez des pièces disponibles dans le commerce lors de l’installation. Fr <QRD3143-C> 22 Black plate (23,1) Section Installation Montage frontal DIN Installation 2 1 Insérez le manchon de montage dans le tableau de bord. Lors de l’installation de cet appareil dans un espace peu profond, utilisez le manchon de montage fourni. Si l’espace est suffisant, utilisez le manchon de montage fourni avec le véhicule. 3 1 2 Retrait et remontage de la face avant Français Vous pouvez retirer la face avant pour protéger l’appareil contre le vol. Appuyez sur la touche de retrait, puis poussez la face avant vers le haut et tirez-la vers vous. Pour les détails, reportez-vous à Retrait de la face avant pour protéger l’appareil contre le vol et à la page 16, Remontage de la face avant. 1 Vis taraudeuse (5 mm × 8 mm) 2 Support de montage 3 Tableau de bord ou console 2 Fixez le manchon de montage en utilisant un tournevis pour courber les pattes métalliques (90°) en place. 1 Serrez deux vis de chaque côté. 03 Retrait de l’appareil 1 Retirez l’anneau de garniture. 2 1 Tableau de bord 2 Manchon de montage # Assurez-vous que l’appareil est correctement mis en place. Toute installation instable peut entraîner des sauts ou autres dysfonctionnements. 1 Anneau de garniture 2 Encoche ! Retirer la face avant permet d’accéder plus facilement à l’anneau de garniture. ! Quand vous remontez l’anneau de garniture, pointez le côté avec l’encoche vers le bas. Montage arrière DIN 1 Déterminez la position appropriée où les trous sur le support et sur le côté de l’appareil se correspondent. 2 Insérez les clés d’extraction fournies dans les deux côtés de l’appareil jusqu’à ce qu’elles s’enclenchent en place. 3 Tirez l’appareil hors du tableau de bord. Fr <QRD3143-C> 23 23 Black plate (24,1) Annexe Informations complémentaires Dépannage Symptôme Symptôme Causes possibles L’écran revient automatiquement à l’affichage ordinaire. Vous n’avez exé- Réexécutez l’opécuté aucune ration. opération pendant 30 secondes. L’étendue de répétition de lecture change de manière inattendue. En fonction de l’étendue de répétition de lecture, l’étendue sélectionnée peut changer lors de la sélection d’un autre dossier ou d’une autre plage ou pendant l’avance ou le retour rapide. Resélectionnez l’étendue de répétition de lecture. Il est impossible de lire les sousdossiers lorsque FLD (répétition du dossier) est sélectionné. Sélectionnez une autre étendue de répétition de lecture. Un sous-dossier n’est pas lu. NO XXXX s’affiche lors de la modification de l’affichage (par exemple NO TITLE). Action corrective L’appareil ne fonctionne pas correctement. Il y a des interférences. Informations complémentaires Causes possibles Action corrective Vous utilisez un autre appareil, tel qu’un téléphone cellulaire, qui transmet des ondes électromagnétiques à proximité de l’appareil. Éloignez tous les appareils électriques qui pourrait provoquer des interférences. Conseils sur la manipulation Lecteur de CD Message Causes possibles ERROR-07, Le disque est 11, 12, 17, 30 sale. ERROR-07, 10, 11, 12, 15, 17, 30, A0 Commun Aucune inforBasculez l’affimation textuelle chage ou la lecn’est intégrée. ture sur une autre plage/un autre fichier. Message Causes possibles Action corrective AMP ERROR Une anomalie de fonctionnement de l’appareil s’est produite ou la connexion des haut-parleurs est incorrecte. Le circuit de protection est activé. Vérifiez la connexion des haut-parleurs. Si le message ne disparaît pas même après avoir éteint puis démarré le moteur, consultez votre distributeur ou un centre d’entretien agréé par Pioneer. Nettoyez le disque. Le disque est rayé. Utilisez un autre disque. Une erreur mécanique ou électrique est survenue. Coupez et remettez le contact d’allumage ou choisissez une autre source, puis revenez au lecteur de CD. Messages d’erreur Quand vous contactez votre distributeur ou le Service d’entretien agréé par Pioneer le plus proche, n’oubliez pas de noter le message d’erreur. Action corrective ERROR-15 Le disque inséré Utilisez un autre est vierge. disque. ERROR-23 Format CD non pris en charge. Utilisez un autre disque. FORMAT READ Le début de la lecture et le début de l’émission des sons sont parfois décalés. Attendez que le message disparaisse pour entendre les sons. NO AUDIO Le disque inséré Utilisez un autre ne contient pas disque. de fichiers pouvant être lus. SKIPPED Le disque inséré Utilisez un autre contient des fi- disque. chiers protégés par DRM. PROTECT Tous les fichiers Utilisez un autre sur le disque in- disque. séré intègrent la protection par DRM. Disques et lecteur Utilisez uniquement des disques affichant l’un ou l’autre des logos suivants. Utilisez des disques 12 cm. N’utilisez pas de disques 8 cm ni un adaptateur pour disques 8 cm. Utilisez seulement des disques conventionnels de forme circulaire. N’utilisez pas de disques ayant une forme particulière. N’introduisez aucun objet dans le logement pour CD autre qu’un CD. N’utilisez pas de disques fendillés, ébréchés, voilés ou présentant d’autres défauts, car ils peuvent endommager le lecteur. Les disques CD-R/RW non finalisés ne peuvent pas être lus. Ne touchez pas la surface enregistrée des disques. Rangez les disques dans leur coffret dès que vous ne les écoutez plus. Ne posez aucune étiquette sur la surface des disques, n’écrivez pas sur un disque, n’appliquez aucun agent chimique sur un disque. Pour nettoyer un CD, essuyez le disque avec un chiffon doux en partant du centre vers l’extérieur. 24 Fr <QRD3143-C> 24 Black plate (25,1) Annexe Informations complémentaires La condensation peut perturber temporairement le fonctionnement du lecteur. Laissez celui-ci s’adapter à la température plus élevée pendant une heure environ. Essuyez également les disques humides avec un chiffon doux. Les cahots de la route peuvent interrompre la lecture d’un disque. Lisez les précautions d’emploi des disques avant de les utiliser. Lors de l’utilisation de disques dont la surface de l’étiquette est imprimable, vérifiez les instructions et les avertissements des disques. L’insertion et l’éjection peuvent ne pas être possibles selon les disques. L’utilisation d’un tel disque risque d’endommager cet appareil. Ne posez aucune étiquette disponible dans le commerce ou tout autre matériau sur la surface des disques. ! Les disques pourraient se déformer et devenir injouables. ! Les étiquettes pourraient se décoller pendant la lecture et empêcher l’éjection des disques, ce qui pourrait endommager l’appareil. Compatibilité des formats audio compressés WMA Extension de fichier : .wma Débit binaire : 48 kbit/s à 320 kbit/s (CBR), 48 kbit/s à 384 kbit/s (VBR) Fréquence d’échantillonnage : 32 kHz, 44,1 kHz, 48 kHz Windows Media Audio Professional, Lossless, Voice/DRM Stream/Stream avec vidéo : incompatible Les DualDiscs sont des disques à deux faces avec un CD enregistrable pour l’audio sur une face et un DVD enregistrable pour la vidéo sur l’autre. Comme la face CD des DualDiscs n’est pas physiquement compatible avec le standard CD général, la lecture de la face CD sur cet appareil peut ne pas être possible. Bits de quantification : 8 et 16 (LPCM), 4 (MS ADPCM) Fréquence d’échantillonnage : 16 kHz à 48 kHz (LPCM), 22,05 kHz et 44,1 kHz (MS ADPCM) Informations supplémentaires Seuls les 32 premiers caractères d’un nom de fichier (incluant l’extension de fichier) ou d’un nom de dossier peuvent être affichés. Les textes russes à afficher sur cet appareil doivent être codés avec un des jeux de caractères suivants : ! Unicode (UTF-8, UTF-16) ! Un jeu de caractères autre que Unicode qui est utilisé dans un environnement Windows et qui est paramétré sur Russe dans le réglage multilingue Fréquence d’échantillonnage : 8 kHz à 48 kHz (32 kHz, 44,1 kHz, 48 kHz pour accentuation) Version étiquette ID3 compatible : 1.0, 1.1, 2.2, 2.3, 2.4 (la Version 2.x de l’étiquette ID3 a priorité sur la Version 1.x.) Quelle que soit la durée du silence entre les plages musicales de l’enregistrement original, la lecture des disques d’audio compressé s’effectue avec une courte pause entre les plages musicales. PRÉCAUTION Ne laissez pas de disque dans un endroit soumis à des températures élevées. Séquence des fichiers audio Sur cet appareil, l’utilisateur ne peut pas affecter de numéros de dossier ni spécifier les séquences de lecture. Exemple de hiérarchie 01 02 1 2 Cet appareil peut ne pas fonctionner correctement selon l’application utilisée pour encoder les fichiers WMA. Disque Débit binaire : 8 kbit/s à 320 kbit/s (CBR), VBR Transfert des données en écriture par paquet : incompatible Extension de fichier : .wav MP3 Extension de fichier : .mp3 DualDiscs WAV Hiérarchie des dossiers pouvant être lus : jusqu’à 8 niveaux (dans la pratique, la hiérarchie compte moins de 2 niveaux). Dossiers pouvant être lus : jusqu’à 99 Français La lecture de certains disques peut être impossible en raison des caractéristiques du disque, de son format, de l’application qui l’a enregistré, de l’environnement de lecture, des conditions de stockage ou d’autres conditions. Charger et éjecter fréquemment un DualDisc peut provoquer des rayures sur le disque. Des rayures importantes peuvent entraîner des problèmes de lecture sur cet appareil. Dans certains cas, un DualDisc peut se retrouver bloqué dans le logement pour CD et ne sera pas éjecté. Pour éviter cela, nous vous recommandons de vous abstenir d’utiliser des DualDiscs avec cet appareil. Pour des informations plus détaillées sur les DualDiscs, veuillez vous reporter aux informations fournies par le fabricant des disques. Informations complémentaires 03 3 4 04 5 6 05 Niveau 1 Niveau 2 Niveau 3 Niveau 4 : Dossier : Fichier d’audio compressé 01 à 05 : Numéro de dossier 1 à 6 : Séquence de lecture Disque La séquence de sélection des dossiers ou d’autres opérations peut différer en fonction du logiciel de codage ou d’écriture. Fichiers pouvant être lus : jusqu’à 999 Système de fichiers : ISO 9660 Niveau 1 et 2, Romeo, Joliet Lecture multi-session : compatible Liste de lecture m3u : incompatible MP3i (MP3 interactif), mp3 PRO : incompatible Fr <QRD3143-C> 25 25 Black plate (26,1) Annexe Informations complémentaires WMA Tableau des caractères cyrilliques D: C D: C D: C D: C D: C :А :Б :В :Г :Д : Е, Ё :Ж :З : И, Й :К :Л :М :Н :О :П :Р :С :Т :У :Ф :Ъ :Я :Х :Ц :Ч : Ш, Щ :Ы :Ь :Э :Ю D : Affichage C : Caractère Droits d’auteur et marques commerciales iTunes Apple et iTunes sont des marques commerciales d’Apple Inc., enregistrées aux États-Unis et dans d’autres pays. MP3 La vente de ce produit comporte seulement une licence d’utilisation privée, non commerciale, et ne comporte pas de licence ni n’implique aucun droit d’utilisation de ce produit pour une diffusion commerciale (c’est-à-dire générant des revenus) en temps réel (terrestre, par satellite, câble et/ou tout autre média), diffusion/streaming via internet, des intranets et/ou d’autres systèmes électroniques de distribution de contenu, telles que les applications audio payante ou audio à la demande. Une licence indépendante est requise pour de telles utilisations. Pour les détails, veuillez visiter le site http://www.mp3licensing.com. 26 Windows Media est une marque déposée ou une marque commerciale de Microsoft Corporation aux États-Unis et/ou dans d’autres pays. Ce produit intègre une technologie détenue par Microsoft Corporation, qui ne peut être utilisée et distribuée que sous licence de Microsoft Licensing, Inc. Informations complémentaires Caractéristiques techniques Généralités Tension d’alimentation ..... 14,4 V CC (10,8 V à 15,1 V acceptable) Mise à la masse ............... Pôle négatif Consommation maximale ................................... 10,0 A Dimensions (L × H × P) : DIN Châssis .............. 178 mm × 50 mm × 165 mm Panneau avant ... 188 mm × 58 mm × 16 mm D Châssis .............. 178 mm × 50 mm × 165 mm Panneau avant ... 170 mm × 46 mm × 16 mm Poids ............................... 1 kg Audio Puissance de sortie maximale ................................... 50 W × 4 70 W × 1/2 W (pour le hautparleur d’extrêmes graves) Puissance de sortie continue ................................... 22 W × 4 (50 Hz à 15 000 Hz, DHT 5 %, impédance de charge 4 W, avec les deux canaux entraînés) Impédance de charge ...... 4 W (4 W à 8 W acceptable) Niveau de sortie maximum de la sortie préamp ................................... 2,0 V Correction physiologique ................................... +10 dB (100 Hz), +6,5 dB (10 kHz) (volume : –30 dB) Égaliseur (Égaliseur graphique à 5 bandes) : Fréquence ................. 80 Hz/250 Hz/800 Hz/ 2,5 kHz/8 kHz Plage d’égalisation ... ±12 dB (par pas de 2 dB) Haut-parleur d’extrêmes graves (mono) : Fréquence ................. 50 Hz/63 Hz/80 Hz/100 Hz/ 125 Hz/160 Hz/200 Hz Pente ........................ –6 dB/oct, –12 dB/oct Gain ......................... +6 dB à –24 dB Phase ....................... Normale/Inverse Lecteur de CD Système ........................... Disques utilisables ........... Rapport signal/bruit ......... Nombre de canaux ........... Format de décodage MP3 ................................... Format de décodage WMA ................................... Compact Disc Digital Audio Disques compacts 94 dB (1 kHz) (réseau IEC-A) 2 (stéréo) MPEG-1 & 2 Couche Audio 3 Ver. 7, 7.1, 8, 9, 10, 11, 12 (2 canaux audio) (Windows Media Player) Format du signal WAV ...... PCM Linéaire & MS ADPCM (Non compressé) Syntoniseur FM Gamme de fréquence ....... 87,5 MHz à 108,0 MHz Sensibilité utile ................ 9 dBf (0,8 µV/75 W, mono, S/B : 30 dB) Rapport signal/bruit ......... 72 dB (réseau IEC-A) Syntoniseur MW (PO) Gamme de fréquence ....... 531 kHz à 1 602 kHz Sensibilité utile ................ 25 µV (S/B : 20 dB) Rapport signal/bruit ......... 62 dB (réseau IEC-A) Syntoniseur LW (GO) Gamme de fréquence ....... 153 kHz à 281 kHz Sensibilité utile ................ 28 µV (S/B : 20 dB) Rapport signal/bruit ......... 62 dB (réseau IEC-A) Remarque Les caractéristiques et la présentation peuvent être modifiées sans avis préalable. Fr <QRD3143-C> 26 Black plate (27,1) Français Fr <QRD3143-C> 27 27 Black plate (28,1) Sezione Prima di iniziare 01 Grazie per aver acquistato questo prodotto PIONEER Leggere attentamente questo manuale prima di utilizzare il prodotto, per assicurarne il corretto utilizzo. È particolarmente importante leggere e osservare le precauzioni contrassegnate da AVVERTENZA e ATTENZIONE contenute in questo manuale. Conservare il manuale in un luogo sicuro e accessibile, per consultazione futura. Prima di iniziare Informazioni sull’unità In caso di problemi Le frequenze del sintonizzatore di questa unità sono destinate all’uso in Europa occidentale, in Asia, nel Medio Oriente, in Africa e in Oceania. L’uso in altre aree può dare come risultato una ricezione non adeguata. La funzione RDS (Radio Data System) è operativa solo nelle aree in cui vengono trasmessi segnali RDS per stazioni FM. Nel caso che questa unità non funzioni correttamente, contattare il rivenditore o il Centro di assistenza autorizzato PIONEER più vicino. ATTENZIONE Questo apparecchio è un prodotto al laser di Classe 1 secondo le norme di sicurezza dei prodotti al laser IEC 60825-1:2007. PRODOTTO LASER DI CLASSE 1 Se si vuole eliminare questo prodotto, non gettarlo insieme ai rifiuti domestici. Esiste un sistema di raccolta differenziata in conformità alle leggi che richiedono appositi trattamenti, recupero e riciclo. Gli utenti privati dei Paesi membri dell’Unione Europea, della Svizzera e della Norvegia possono portare i propri prodotti elettronici gratuitamente presso i centri di raccolta specificati o presso il rivenditore al dettaglio (se l’acquisto è stato eseguito presso un rivenditore di questo tipo). Per i Paesi non specificati in precedenza, contattare le autorità locali per informazioni sul corretto metodo di smaltimento. In questo modo si garantirà che il prodotto smaltito subisca i processi di trattamento, recupero e riciclaggio necessari per prevenire i potenziali effetti negativi per l’ambiente e la salute umana. 28 ATTENZIONE ! Non lasciare che questa unità entri in contatto con liquidi, in caso contrario possono verificarsi scosse elettriche. Inoltre, se questa unità entra in contatto con liquidi, può subire danni oppure emettere fumo o surriscaldarsi. ! Il CarStereo-Pass Pioneer può essere usato solo in Germania. ! Mantenere sempre il volume basso abbastanza da poter udire i suoni provenienti dall’esterno. ! Evitare l’esposizione all’umidità. ! Se la batteria viene scollegata o si scarica, la memoria delle preselezioni viene cancellata. Nota Le operazioni di impostazione delle funzioni vengono completate anche se il menu viene chiuso prima della conferma. It <QRD3143-C> 28 Black plate (29,1) Sezione Funzionamento dell’unità Funzionamento dell’unità Unità principale Indicatore 1 2 34 5 6 7 8 9 a b Componente c d 8 BAND 2 SRC/OFF 9 (indietro)/ DIMMER (varialuce) MULTI-CONTROL (M.C.) 4 (lista) 5 DISP Vano d’inserimento dei dischi 6 (lista) 2 Sezione delle informazioni secondarie Vengono visualizzate le informazioni secondarie. 3 TA (notiziari sul traffico) La funzione TA è attivata. 4 TP (identificazione dei programmi sul traffico) È sintonizzata una stazione TP. a c/d b Da 1/ c Connettore di ingresso ausiliario (AUX) (connettore stereo da 3,5 mm) d (Sound Retriever) 6 LOC La ricerca di sintonia in modo locale è attiva. 7 (ripetizione) È attiva la funzione di riproduzione cartella. a 6/ 8 9 Indicazioni sul display 1 2 3 4 5 6 8 7 a 9 (casuale) Tasto Rimozione re) a È attivata la funzione Sound Retriever. 5 (equalizzato- 7 La funzione elenco è attiva. Sezione delle informazioni principali È attiva la riproduzione casuale. ! Sintonizzatore: banda e frequenza ! RDS: nome di servizio del programma, informazioni PTY e altre informazioni letterali ! Lettore CD: tempo di riproduzione trascorso e informazioni di testo Viene visualizzato quando esiste una cartella o un menu di livello inferiore. Menu di configurazione Portando su ON l’interruttore della chiave di avviamento dopo l’installazione, sul display compare il menu di configurazione. È possibile configurare le opzioni di menu riportate di seguito. 1 Dopo aver installato l’unità, portare l’interruttore della chiave di avviamento su ON. Viene visualizzata l’indicazione SET UP. 2 Ruotare M.C. per selezionare YES. # Se non si effettuano operazioni per 30 secondi, il menu di configurazione non sarà visualizzato. # Se non si desidera eseguire la configurazione in questo momento, ruotare M.C. per selezionare NO. Premere per selezionare. Se si seleziona NO, non è possibile definire le impostazioni nel menu di configurazione. 3 Premere M.C. per selezionare. 4 Attenersi alle procedure descritte di seguito per configurare il menu. Per passare all’opzione di menu successiva, occorre confermare la selezione. LANGUAGE (multilingue) Questa unità è in grado di visualizzare le informazioni di testo dei file audio compressi se sono state incorporate in inglese o russo. ! Se la lingua incorporata e l’impostazione della lingua selezionata non corrispondono, le informazioni di testo potrebbero non essere visualizzate correttamente. ! Alcuni caratteri potrebbero non essere visualizzati correttamente. 1 Ruotare M.C. per selezionare l’impostazione desiderata. ENG (Inglese)—РУС (Russo) 2 Premere M.C. per confermare la selezione. 1 2 3 4 Ruotare M.C. per regolare le ore. Premere M.C. per selezionare i minuti. Ruotare M.C. per regolare i minuti. Premere M.C. per confermare la selezione. FM STEP (passo di sintonizzazione FM) Normalmente il passo per la sintonizzazione in FM impiegato dalla ricerca di sintonia è 50 kHz. Se sono attivate le funzioni AF o TA il passo di sintonizzazione cambia automaticamente a 100 kHz. Se è attivata la funzione AF, è preferibile impostare il passo di sintonizzazione a 50 kHz. ! Il passo di sintonizzazione rimane a 50 kHz durante la sintonizzazione manuale. 1 Ruotare M.C. per selezionare il passo di sintonizzazione FM. 50 (50 kHz)—100 (100 kHz) 2 Premere M.C. per confermare la selezione. Viene visualizzata l’indicazione QUIT. Italiano h (espulsione) 3 1 Componente 1 Stato 02 5 Per completare le impostazioni, ruotare M.C. per selezionare YES. # Se si desidera modificare nuovamente l’impostazione, ruotare M.C. per selezionare NO. Premere per selezionare. 6 Premere M.C. per selezionare. Note ! È possibile configurare le opzioni di menu dal menu di sistema. Per informazioni dettagliate sulle impostazioni, vedere Menu di sistema a pagina 33. ! È possibile annullare il menu di configurazione premendo SRC/OFF. Funzionamento di base Importante ! Rimuovere e inserire il frontalino delicatamente. CLOCK SET (impostazione dell’orologio) It <QRD3143-C> 29 29 Black plate (30,1) Sezione Funzionamento dell’unità 02 ! Evitare di sottoporre il frontalino a urti eccessivi. ! Mantenere il frontalino lontano dalla luce solare diretta e dalle alte temperature. ! Per evitare danni ai dispositivi o agli interni del veicolo, accertarsi di scollegare gli eventuali cavi e i dispositivi collegati al frontalino, prima di rimuoverlo. Rimozione del frontalino per proteggere l’unità dai furti 1 Premere il tasto di rimozione per sganciare il frontalino. 2 Spingere il frontalino verso l’alto (M) e quindi tirarlo verso l’esterno (N). Funzionamento dell’unità Accensione dell’unità 1 Premere SRC/OFF per accendere l’unità. Spegnimento dell’unità 1 Premere e tenere premuto SRC/OFF fino a quando l’unità non si spegne. Selezione di una sorgente 1 Premere SRC/OFF per passare in rassegna: TUNER (Sintonizzatore)—CD (Lettore CD)— AUX (AUX) Regolazione del volume 1 Ruotare M.C. per regolare il volume. ATTENZIONE Per motivi di sicurezza, parcheggiare il veicolo quando si rimuove il frontalino. 3 Tenere sempre il frontalino nella custodia di protezione quando non è collegato all’unità. Reinserimento del frontalino 1 Fare scorrere il frontalino verso sinistra. Inserire le linguette sul lato sinistro dell’unità principale nei corrispondenti alloggiamenti sul frontalino. Nota Quando il conduttore isolato blu/bianco di questa unità viene collegato al terminale di controllo del relè dell’antenna automatica, l’antenna dell’automobile si estende quando si accende l’unità. Per ritirare l’antenna, spegnere la sorgente. Operazioni col menu più frequentemente utilizzate Ritorno al display precedente Ritorno all’elenco precedente (la cartella superiore di un livello) 1 Premere /DIMMER. 2 Premere il lato destro del frontalino fino a quando è saldamente installato. Se non è possibile collegare il frontalino all’unità principale, accertarsi di aver posizionato il frontalino sull’unità principale in modo corretto. Inserendo il frontalino con forza eccessiva, l’unità o il frontalino potrebbero subire danni. 30 Ritorno al display normale Annullamento del menu principale 1 Premere BAND. Ritorno al display normale dall’elenco 1 Premere BAND. Sintonizzatore Funzionamento di base Memorizzazione e richiamo delle stazioni per ciascuna banda Uso dei tasti di preselezione sintonia Selezione di una banda 1 Premere BAND fino a quando viene visualizzata la banda desiderata (FM1, FM2, FM3 per FM o MW/LW). Selezione delle stazioni preselezionate 1 Premere c o d. ! Selezionare PCH (canale preselezionato) in SEEK per utilizzare questa funzione. Per informazioni dettagliate sulle impostazioni, vedere SEEK (impostazione tasto sinistro/destro) nella pagina seguente. Sintonizzazione manuale (passo per passo) 1 Premere c o d. ! Selezionare MAN (sintonizzazione manuale) in SEEK per utilizzare questa funzione. Per informazioni dettagliate sulle impostazioni, vedere SEEK (impostazione tasto sinistro/destro) nella pagina seguente. Ricerca 1 Premere e tenere premuto c o d e poi rilasciare. È possibile annullare la ricerca di sintonia premendo brevemente c o d. Se si spinge e si tiene premuto c o d, è possibile saltare le stazioni. La ricerca di sintonia viene avviata non appena si rilascia c o d. Nota È possibile attivare e disattivare (on/off) la funzione AF (ricerca delle frequenze alternative) di questa unità. Per le operazioni normali di sintonizzazione, la funzione AF deve essere disattivata (vedere AF (ricerca delle frequenze alternative) nella pagina seguente). 1 Quando viene individuata una stazione che si desidera memorizzare, premere uno dei tasti di preselezione sintonia (da 1/ a 6/ ), mantenendolo premuto fino a quando il numero di preselezione non cessa di lampeggiare. 2 Premere e tenere premuto uno dei tasti di preselezione sintonia (da 1/ a 6/ ) per selezionare la stazione desiderata. Commutazione del display Selezione delle informazioni di testo desiderate 1 Premere DISP per alternare le seguenti impostazioni: ! FREQUENCY (nome di servizio del programma o frequenza) ! BRDCST INFO (nome di servizio del programma/Informazioni PTY) ! CLOCK (nome della sorgente e orologio) Note ! Se non è possibile ottenere il nome di servizio del programma in FREQUENCY, al suo posto viene visualizzata la frequenza di trasmissione. Se invece il nome di servizio del programma viene rilevato, verrà visualizzato. ! BRDCST INFO le informazioni di testo cambieranno automaticamente. ! È possibile modificare le informazioni a seconda della banda. ! Le informazioni di testo che possono essere modificate dipendono dall’area. Uso delle funzioni PTY È possibile sintonizzarsi su una stazione usando le informazioni PTY (tipo di programma). It <QRD3143-C> 30 Black plate (31,1) Sezione Funzionamento dell’unità Elenco PTY NEWS/INFO (notizie e informazioni) NEWS (Notizie), AFFAIRS (Problemi attuali), INFO (Informazione), SPORT (Sport), WEATHER (Informazioni meteorologiche), FINANCE (Economia) POPULAR (musica pop) POP MUS (Musica popolare), ROCK MUS (Musica rock), EASY MUS (Musica rilassante), OTH MUS (Altra musica), JAZZ (Jazz), COUNTRY (Musica Country), NAT MUS (Musica nazionale), OLDIES (Vecchi successi), FOLK MUS (Musica Folk) L. CLASS (Musica classica leggera), CLASSIC (Musica classica) OTHERS (altro) EDUCATE (Educazione), DRAMA (Teatro), CULTURE (Cultura), SCIENCE (Scienza), VARIED (Varietà), CHILDREN (Bambini), SOCIAL (Questioni sociali), RELIGION (Religione), PHONE IN (Chiamate in diretta), TOURING (Viaggi), LEISURE (Tempo libero), DOCUMENT (Documentari) Impostazioni delle funzioni 1 Premere M.C. per visualizzare il menu principale. 2 Ruotare M.C. per modificare l’opzione di menu; premere per selezionare FUNCTION. 3 Ruotare M.C. per selezionare la funzione. Dopo aver effettuato la selezione, è possibile regolare le funzioni descritte di seguito. # Se è selezionata la banda MW/LW, è possibile selezionare solo BSM, LOCAL o SEEK. La ricerca di sintonia in modo locale consente di sintonizzare solo le stazioni radio con segnali radio sufficientemente potenti per una buona ricezione. 1 Premere M.C. per selezionare l’impostazione desiderata. FM: OFF—LV1—LV2—LV3—LV4 MW/LW: OFF—LV1—LV2 L’impostazione di livello massimo consente la ricezione solo delle stazioni più forti, mentre i livelli più bassi consentono di ricevere stazioni più deboli. TA (attesa di notiziari sul traffico) 1 Premere M.C. per attivare o disattivare l’attesa di notiziari sul traffico. AF (ricerca delle frequenze alternative) 1 Premere M.C. per attivare e disattivare la funzione AF. NEWS (interruzione dei programmi per i notiziari) 1 Premere M.C. per attivare o disattivare la funzione NOTIZIE. BSM (memorizzazione delle stazioni migliori) SEEK (impostazione tasto sinistro/destro) La funzione BSM (memorizzazione delle stazioni migliori) memorizza automaticamente le sei stazioni più forti in ordine di forza del segnale. 1 Premere M.C. per attivare la funzione BSM. Per annullare, premere nuovamente M.C. È possibile assegnare una funzione ai tasti sinistro e destro dell’unità. Selezionare MAN (sintonizzazione manuale) per eseguire la sintonizzazione manuale o PCH (canali preselezionati) per scegliere i canali preselezionati. 1 Premere M.C. per selezionare MAN o PCH. REGION (regionale) Quando si utilizza la funzione AF, la funzione regionale limita la selezione alle stazioni che trasmettono programmi regionali. 1 Premere M.C. per attivare o disattivare la funzione regionale. 02 CD/CD-R/CD-RW Funzionamento di base Riproduzione di CD/CD-R/CD-RW 1 Inserire un disco nel vano d’inserimento dei dischi, con il lato dell’etichetta rivolto verso l’alto. Espulsione dei CD/CD-R/CD-RW 1 Premere h. Selezione di una cartella 1 Premere 1/ o 2/ . Italiano Ricerca di una stazione RDS tramite le informazioni PTY È possibile ricercare programmi di trasmissioni di tipo generale, come quelli elencati nella sezione seguente. Vedere in questa pagina. (elenco). 1 Premere 2 Ruotare M.C. per selezionare un tipo di programma. NEWS/INFO—POPULAR—CLASSICS— OTHERS 3 Premere M.C. per avviare la ricerca. L’unità ricerca una stazione che trasmette il tipo di programma selezionato. Quando viene trovata una stazione, viene visualizzato il nome di servizio del programma. ! Per annullare la ricerca premere nuovamente M.C. ! Il programma di alcune stazioni può essere diverso da quello indicato dal PTY (tipo di programma) trasmesso. ! Se nessuna stazione trasmette il tipo di programma ricercato, per circa due secondi viene visualizzata l’indicazione NOT FOUND e poi il sintonizzatore torna alla stazione originale. Funzionamento dell’unità Selezione di una traccia 1 Premere c o d. Esegue l’avanzamento rapido/la modalità inversa rapida 1 Premere e tenere premuto c o d. ! Quando si riproducono file audio compressi, durante l’avanzamento rapido e la modalità inversa non viene emesso audio. Ritorno alla cartella principale 1 Premere e tenere premuto BAND. Passaggio da audio compresso a CD-DA 1 Premere BAND. LOCAL (ricerca di sintonia in modo locale) CLASSICS (musica classica) It <QRD3143-C> 31 31 Black plate (32,1) Sezione Funzionamento dell’unità 02 Commutazione del display Selezione delle informazioni di testo desiderate 1 Premere DISP per alternare le seguenti impostazioni: CD-DA ! ELAPSED TIME (numero di brano e tempo di riproduzione) ! CLOCK (nome della sorgente e orologio) ! SPEANA (analizzatore di spettro) CD-TEXT ! TRACK INFO (titolo del brano/artista del brano/titolo del disco) ! ELAPSED TIME (numero di brano e tempo di riproduzione) ! CLOCK (nome della sorgente e orologio) ! SPEANA (analizzatore di spettro) MP3/WMA/WAV ! TRACK INFO (titolo del brano/nome dell’artista/titolo dell’album) ! FILE INFO (nome del file/nome della cartella) ! ELAPSED TIME (numero di brano e tempo di riproduzione) ! CLOCK (nome della sorgente e orologio) ! SPEANA (analizzatore di spettro) Note ! Le informazioni di testo TRACK INFO e FILE INFO cambieranno automaticamente. ! A seconda della versione di iTunes utilizzata per scrivere i file MP3 o del tipo di file multimediali, il testo memorizzato su un file audio potrebbe essere incompatibile e non essere visualizzato correttamente. ! Le informazioni di testo che possono essere cambiate dipendono dal tipo di supporto. Selezione e riproduzione di file/ brani dall’elenco dei nomi Funzionamento dell’unità 2 Utilizzare M.C. per selezionare il nome del file (o il nome della cartella) desiderato. Selezione di un file o di una cartella 1 Ruotare M.C. Riproduzione 1 Quando è selezionato un file o un brano, premere M.C. Visualizzazione di un elenco dei file (o delle cartelle) nella cartella selezionata 1 Quando è selezionata una cartella, premere M.C. Riproduzione di un brano nella cartella selezionata 1 Quando è selezionata una cartella, premere e tenere premuto M.C. Operazioni con i pulsanti speciali Selezione di un intervallo di ripetizione per alternare: 1 Premere 6/ ! ALL – Ripete tutti i brani ! ONE – Ripete il brano corrente ! FLD – Ripete la cartella corrente Riproduzione di brani in ordine casuale per attivare o disattivare la ri1 Premere 5/ produzione casuale. I brani contenuti nell’intervallo di ripetizione selezionato vengono riprodotti in ordine casuale. ! Per cambiare brano durante la riproduzione casuale, premere d per passare al brano successivo. Se si preme c, viene riavviata la riproduzione del brano corrente dall’inizio. Messa in pausa della riproduzione 1 Premere 4/PAUSE per attivare o disattivare la pausa. Miglioramento dell’audio compresso e ripristino del suono completo (funzione Sound Retriever) 1 Premere 3/S.Rtrv per passare in rassegna: 1—2—OFF (disattivata) 1 è efficace per le velocità di compressione basse, mentre 2 è efficace per le velocità di compressione alte. Impostazioni delle funzioni 1 Premere M.C. per visualizzare il menu principale. 2 Ruotare M.C. per modificare l’opzione di menu; premere per selezionare FUNCTION. Dopo aver effettuato la selezione, è possibile regolare la funzione descritta di seguito. 3 Ruotare M.C. per selezionare la funzione audio. Dopo aver effettuato la selezione, è possibile regolare le funzioni audio descritte di seguito. ! FADER non è disponibile se l’impostazione SUB.W/SUB.W è selezionata in SP-P/O MODE. Per ulteriori dettagli, vedere SP-P/O MODE (uscita posteriore e impostazione pre-out) a pagina 34. ! SUB.W, SUB.W CTRL e HPF SETTING non sono disponibili se l’impostazione REAR/REAR è selezionata in SP-P/O MODE. Per ulteriori dettagli, vedere SP-P/O MODE (uscita posteriore e impostazione pre-out) a pagina 34. ! SUB.W CTRL e HPF SETTING non sono disponibili se l’impostazione SUB.W è selezionata in OFF. Per ulteriori dettagli, vedere SUB.W (impostazione on/off del subwoofer) nella pagina seguente. FADER (regolazione dissolvenza) S.RTRV (Sound Retriever) Questa funzione migliora automaticamente l’audio compresso e ripristina il suono completo. 1 Premere M.C. per selezionare l’impostazione desiderata. Per ulteriori dettagli, vedere Miglioramento dell’audio compresso e ripristino del suono completo (funzione Sound Retriever) in questa pagina. Regolazione dell’audio 1 Premere M.C. per visualizzare la modalità di impostazione. 2 Ruotare M.C. per regolare il bilanciamento degli altoparlanti anteriori/posteriori. BALANCE (regolazione del bilanciamento) 1 Premere M.C. per visualizzare la modalità di impostazione. 2 Ruotare M.C. per regolare il bilanciamento dell’altoparlante sinistro/destro. EQ SETTING (richiamo dell’equalizzatore) 1 Premere M.C. per visualizzare il menu principale. 2 Ruotare M.C. per modificare l’opzione di menu; premere per selezionare AUDIO. 1 Premere per passare alla modalità dell’elenco dei nomi file/brani. 32 It <QRD3143-C> 32 Black plate (33,1) Sezione Funzionamento dell’unità LOUDNESS (sonorità) La sonorità compensa le deficienze nelle gamme delle frequenze basse e alte a basso volume. 1 Premere M.C. per selezionare l’impostazione desiderata. OFF (non attiva)—LOW (bassa)—MID (media) —HI (alta) SUB.W (impostazione on/off del subwoofer) Questa unità è dotata di un’uscita subwoofer che può essere attivata o disattivata. 1 Premere M.C. per selezionare l’impostazione desiderata. NOR (fase normale)—REV (fase invertita)— OFF (subwoofer disattivato) SUB.W CTRL (regolazione del subwoofer) Solo frequenze più basse di quelle presenti nell’intervallo selezionato vengono emesse dal subwoofer. 1 Premere M.C. per visualizzare la modalità di impostazione. 2 Premere M.C. per alternare le seguenti impostazioni: Frequenza di taglio—Livello di uscita—Livello pendenza I valori regolabili lampeggiano. 3 Ruotare M.C. per selezionare l’impostazione desiderata. Frequenza di taglio: 50HZ—63HZ—80HZ— 100HZ—125HZ—160HZ—200HZ Livello di uscita: da –24 a +6 Livello pendenza: –6— –12 BASS BOOST (incremento dei bassi) 1 Premere M.C. per visualizzare la modalità di impostazione. 2 Ruotare M.C. per selezionare il livello desiderato. A seconda se il livello aumenta o diminuisce, viene visualizzata l’indicazione da 0 a +6. HPF SETTING (regolazione del filtro passa alto) Se si desidera che i suoni bassi provenienti dalla gamma di frequenza dell’uscita subwoofer non siano riprodotti dagli altoparlanti anteriori o posteriori, attivare la funzione HPF (filtro passa alto). Solo le frequenze più alte di quelle comprese nell’intervallo selezionato vengono emesse dagli altoparlanti anteriori o posteriori. 1 Premere M.C. per visualizzare la modalità di impostazione. 2 Premere M.C. per alternare le seguenti impostazioni: Frequenza di taglio—Livello pendenza 3 Ruotare M.C. per selezionare l’impostazione desiderata. Frequenza di taglio: OFF—50HZ—63HZ— 80HZ—100HZ—125HZ—160HZ—200HZ Livello pendenza: –6— –12 SLA (regolazione del livello della sorgente) SLA (funzione di regolazione del livello della sorgente) consente di regolare il livello di volume di ogni sorgente per prevenire cambiamenti radicali di volume quando si passa da una sorgente all’altra. ! Le impostazioni sono basate sul livello di volume FM, che rimane immutato. ! Con questa funzione è anche possibile regolare il livello di volume MW/LW. ! Quando si seleziona FM come sorgente, non è possibile passare alla funzione SLA. 1 Premere M.C. per visualizzare la modalità di impostazione. 2 Ruotare M.C. per regolare il volume della sorgente. Intervallo di regolazione: da +4 a –4 02 Menu di sistema Importante La modalità PW SAVE (risparmio energetico) viene annullata se la batteria del veicolo viene scollegata e sarà necessario riattivarla dopo aver ricollegato la batteria. Se la funzione PW SAVE (risparmio energetico) è disattivata, a seconda del metodo di collegamento, l’unità potrebbe continuare a consumare energia dalla batteria se l’interruttore della chiave di avviamento del veicolo non è dotato di posizione ACC (accessori). Italiano 1 Premere M.C. per visualizzare la modalità di impostazione. 2 Ruotare M.C. per selezionare l’equalizzatore. POWERFUL—NATURAL—VOCAL—CUSTOM1—CUSTOM2—FLAT—SUPER BASS La banda di equalizzazione e il livello dell’equalizzatore possono essere personalizzati se è selezionata l’impostazione CUSTOM1 o CUSTOM2. Se si seleziona CUSTOM1 o CUSTOM2, completare la procedure descritta di seguito. Se si selezionano altre opzioni, premere M.C. per tornare al display precedente. ! L’impostazione CUSTOM1 può essere impostata separatamente per ciascuna sorgente. ! CUSTOM2 è un’impostazione condivisa utilizzata per tutte le sorgenti. 3 Premere M.C. per visualizzare la modalità di impostazione. 4 Premere M.C. per alternare le seguenti impostazioni: Banda d’equalizzazione—Livello equalizzatore 5 Ruotare M.C. per selezionare l’impostazione desiderata. Banda d’equalizzazione: 80HZ—250HZ— 800HZ—2.5KHZ—8KHZ Livello equalizzatore: +6 a –6 ! È inoltre possibile cambiare l’equalizzatore . premendo ripetutamente Funzionamento dell’unità 1 Premere M.C. per visualizzare il menu principale. 2 Ruotare M.C. per modificare l’opzione di menu; premere per selezionare SYSTEM. 3 Ruotare M.C. per selezionare la funzione del menu di sistema. Dopo aver effettuato la selezione, è possibile regolare le funzioni del menu di sistema descritte di seguito. LANGUAGE (multilingue) Questa unità è in grado di visualizzare le informazioni di testo dei file audio compressi se sono state incorporate in inglese o russo. ! Se la lingua incorporata e l’impostazione della lingua selezionata non corrispondono, le informazioni di testo potrebbero non essere visualizzate correttamente. ! Alcuni caratteri potrebbero non essere visualizzati correttamente. 1 Ruotare M.C. per selezionare l’impostazione desiderata. ENG (Inglese)—РУС (Russo) CLOCK SET (impostazione dell’orologio) It <QRD3143-C> 33 33 Black plate (34,1) Sezione Funzionamento dell’unità 02 1 Premere M.C. per visualizzare la modalità di impostazione. 2 Premere M.C. per selezionare il segmento del display dell’orologio che si desidera impostare. Ora—Minuto 3 Ruotare M.C. per regolare l’orologio. 12H/24H (nota temporale) 1 Premere M.C. per selezionare l’impostazione desiderata. 12H (formato orologio a 12 ore)—24H (formato orologio a 24 ore) AUTO PI (ricerca automatica PI) Funzionamento dell’unità PW SAVE (risparmio energetico) Attivando questa funzione, è possibile ridurre il consumo di energia della batteria. ! L’attivazione della sorgente è l’unica operazione consentita quando questa funzione è attiva. 1 Premere M.C. per attivare o disattivare la modalità di risparmio energetico. Attivazione/disattivazione del varialuce È possibile regolare il livello della luminosità. L’unità può ricercare automaticamente una stazione diversa con la stessa programmazione, anche durante il richiamo delle preselezioni. 1 Premere M.C. per attivare o disattivare la ricerca automatica PI. 1 Premere M.C. per visualizzare il menu principale. AUX (ingresso ausiliario) 3 Premere M.C. per selezionare l’impostazione desiderata. OFF (disattivato)—ON (attivato) Attivare questa impostazione se a questa unità viene collegato un dispositivo ausiliario. 1 Premere M.C. per attivare o disattivare AUX. MUTE MODE (modalità di silenziamento) Il suono del sistema viene silenziato o attenuato automaticamente quando viene ricevuto un segnale da un apparecchio dotato di funzione di silenziamento. 1 Premere M.C. per visualizzare la modalità di impostazione. 2 Ruotare M.C. per selezionare l’impostazione desiderata. È possibile selezionare una delle opzioni dall’elenco seguente: ! MUTE – Silenziamento ! 20dB ATT – Attenuazione (20dB ATT ha un effetto più accentuato rispetto a 10dB ATT) ! 10dB ATT – Attenuazione 2 Ruotare M.C. per visualizzare ILLUMI, quindi premere per selezionare. ! È inoltre possibile modificare l’impostazione del varialuce premendo e tenendo premuto /DIMMER. Menu iniziale 1 Premere e tenere premuto SRC/OFF fino a quando l’unità non si spegne. 2 Premere e tenere premuto SRC/OFF fino a visualizzare sul display il menu principale. 3 Ruotare M.C. per modificare l’opzione di menu; premere per selezionare INITIAL. 4 Ruotare M.C. per selezionare la funzione del menu iniziale. Dopo aver effettuato la selezione, è possibile regolare le funzioni del menu iniziale descritte di seguito. FM STEP (passo di sintonizzazione FM) Normalmente il passo per la sintonizzazione in FM impiegato dalla ricerca di sintonia è 50 kHz. Se sono attivate le funzioni AF o TA il passo di sintonizzazione cambia automaticamente a 100 kHz. Se è attivata la funzione AF, è preferibile impostare il passo di sintonizzazione a 50 kHz. ! Il passo di sintonizzazione rimane a 50 kHz durante la sintonizzazione manuale. 1 Premere M.C. per selezionare il passo di sintonizzazione FM. 50 (50 kHz)—100 (100 kHz) SP-P/O MODE (uscita posteriore e impostazione pre-out) Le uscite degli altoparlanti posteriori e l’uscita RCA di questa unità possono essere utilizzate per collegare altoparlanti a gamma completa o un subwoofer. Selezionare l’opzione più adatta alla configurazione. 1 Premere M.C. per visualizzare la modalità di impostazione. 2 Ruotare M.C. per selezionare l’impostazione desiderata. È possibile selezionare una delle opzioni dall’elenco seguente: ! REAR/SUB.W – Selezionare quando alle uscite degli altoparlanti posteriori sono collegati altoparlanti a gamma completa e all’uscita RCA è collegato un subwoofer. ! SUB.W/SUB.W – Selezionare quando alle uscite degli altoparlanti posteriori è collegato direttamente un subwoofer senza un amplificatore ausiliario e all’uscita RCA è collegato un subwoofer. ! REAR/REAR – Selezionare quando alle uscite degli altoparlanti posteriori e all’uscita RCA sono collegati altoparlanti a gamma completa. Se alle uscite degli altoparlanti posteriori è collegato un altoparlante a gamma completa e l’uscita RCA non viene utilizzata, è possibile selezionare REAR/SUB.W o REAR/REAR. Menu di sistema 1 Premere e tenere premuto SRC/OFF fino a quando l’unità non si spegne. 2 Premere e tenere premuto SRC/OFF fino a visualizzare sul display il menu principale. 3 Ruotare M.C. per modificare l’opzione di menu; premere per selezionare SYSTEM. 34 It <QRD3143-C> 34 Black plate (35,1) Sezione Funzionamento dell’unità Installazione 02 03 4 Ruotare M.C. per selezionare la funzione del menu di sistema. Dopo aver effettuato la selezione, è possibile regolare le funzioni del menu di sistema descritte di seguito. Per ulteriori dettagli, vedere Menu di sistema a pagina 33. Uso della sorgente AUX 3 Ruotare M.C. per visualizzare DEMO OFF, quindi premere per selezionare. 4 Ruotare M.C. per selezionare YES. 5 Premere M.C. per selezionare. Collegamenti Importante ! Quando si installa questa unità in un veicolo che non dispone della posizione ACC (accessoria) per l’interruttore della chiave di avviamento, se non si collega il cavo rosso a un terminale accoppiato al funzionamento dell’interruttore della chiave di avviamento, la batteria potrebbe scaricarsi. OF F O N 1 Collegare il cavo mini plug stereo al connettore di ingresso ausiliario (AUX). T Commutazione del display Selezione delle informazioni di testo desiderate 1 Premere DISP per alternare le seguenti impostazioni: ! Nome sorgente ! Nome della sorgente e orologio Se viene visualizzato un display indesiderato Per disattivare il display indesiderato, utilizzare la procedura descritta di seguito. 1 Premere M.C. per visualizzare il menu principale. 2 Ruotare M.C. per modificare l’opzione di menu; premere per selezionare SYSTEM. Con posizione ACC Senza posizione ACC ! Se questa unità viene utilizzata in condizione diverse dalle seguenti, potrebbero verificarsi incendi o malfunzionamenti. — Veicoli dotati di batteria da 12 volt e messa a terra negativa. — Altoparlanti con uscita nominale da 50 W e impedenza nominale compresa tra 4 W e 8 W. ! Per evitare rischi di cortocircuito, surriscaldamento o malfunzionamento, accertarsi di seguire le indicazioni riportate di seguito. — Prima dell’installazione, scollegare il morsetto negativo della batteria. — Assicurare i cavi con morsetti per cavi o nastro adesivo. Per proteggere i cavi, avvolgere nastro adesivo attorno agli stessi nei punti in cui entrano in contatto con parti metalliche. — Posizionare tutti i cavi in modo che non possano entrare in contatto con componenti mobili, come la leva del cambio e i binari dei sedili. — Non posizionare i cavi in luoghi soggetti a surriscaldamento, come le bocchette dell’impianto di riscaldamento. — Non collegare il cavo giallo alla batteria facendolo passare attraverso fori nel vano motore. — Rivestire tutti i connettori scollegati con nastro isolante. ! Quando questa unità è accesa, i segnali di controllo vengono trasmessi dal cavo blu/ bianco. Collegarlo al telecomando del sistema di amplificazione di potenza o al terminale di controllo del relè dell’antenna automatica del veicolo (max. 300 mA 12 V CC). Se il veicolo è dotato di un’antenna a vetro, collegarla al terminale di alimentazione di potenza dell’antenna. ! Non collegare mai il cavo blu/bianco al terminale di alimentazione dell’amplificatore di potenza esterno. Inoltre, non collegarlo mai al terminale di alimentazione dell’antenna automatica. In caso contrario, la batteria potrebbe scaricarsi o potrebbero verificarsi malfunzionamenti. ! Il cavo nero è la messa a terra. I cavi di messa a terra di questa unità e di altre apparecchiature (soprattutto per i prodotti ad alta tensione, quali amplificatori di potenza) devono essere collegati separatamente. In caso contrario, se scollegati accidentalmente, potrebbero provocare incendi o malfunzionamenti. Italiano Nota Non è possibile selezionare la sorgente AUX se non viene attivata l’impostazione dell’apparecchio ausiliario. Per ulteriori dettagli, vedere AUX (ingresso ausiliario) nella pagina precedente. STAR 2 Premere SRC/OFF per selezionare AUX come sorgente. — Non accorciare i cavi. — Non condividere mai l’alimentazione con altri dispositivi tagliando l’isolante del cavo di alimentazione dell’unità. La capacità di carico di corrente del cavo è limitata. — Utilizzare esclusivamente un fusibile con la portata prescritta. — Non collegare mai direttamente a terra il cavo negativo dell’altoparlante. — Non legare mai assieme cavi negativi di più altoparlanti. Questa unità 1 3 4 2 5 It <QRD3143-C> 35 35 Black plate (36,1) Sezione Installazione 03 1 2 3 4 5 Installazione Ingresso cavo di alimentazione Uscita posteriore o del subwoofer Ingresso antenna Fusibile (10 A) Ingresso telecomando cablato È possibile collegare un adattatore per telecomando cablato (venduto a parte). Cavo di alimentazione 3 4 5 2 7 1 6 3 4 5 6 8 a 9 e b c d 1 All’ingresso del cavo di alimentazione 2 A seconda del tipo di veicolo, la funzione di 3 e 5 potrebbe essere diversa. In questo caso, accertarsi di collegare 4 a 5 e 6 a 3. 3 Giallo Riserva (o accessorio) 4 Giallo Collegare al terminale di alimentazione costante 12 V. 5 Rosso Accessorio (o riserva) 6 Rosso Collegare al terminale controllato dall’interruttore di accensione (12 V CC). 7 Collegare insieme i cavi dello stesso colore. 36 8 Nero (messa a terra telaio) 9 Blu/bianco La posizione dei pin del connettore ISO sarà diversa a seconda del tipo di veicolo. Collegare 9 e b quando il Pin 5 è del tipo controllo antenna. In un altro tipo di veicolo, non collegare mai 9 e b. a Blu/bianco Collegare al terminale di controllo del sistema dell’amplificatore di potenza (max. 300 mA 12 V CC). b Blu/bianco Collegare al terminale di controllo del relè dell’antenna automatica (max. 300 mA 12 V CC). c Giallo/nero Se si utilizza un apparecchio dotato di funzione di silenziamento, collegare questo cavo al cavo di silenziamento audio di tale apparecchio. In caso contrario, non collegare il cavo di silenziamento audio. d Cavi altoparlanti Bianco: Anteriore sinistro + Bianco/nero: Anteriore sinistro * Grigio: Anteriore destro + Grigio/nero: Anteriore destro * Verde: Posteriore sinistro + o subwoofer + Verde/nero: Posteriore sinistro * o subwoofer * Viola: Posteriore destro + o subwoofer + Viola/nero: Posteriore destro * o subwoofer * e Connettore ISO In alcuni veicoli, il connettore ISO potrebbe essere diviso in due. In questo caso, accertarsi di collegare entrambi i connettori. Note ! Modifica delle impostazioni di menu iniziali di questa unità. Vedere SP-P/O MODE (uscita posteriore e impostazione pre-out) a pagina 34. L’uscita subwoofer di questa unità è mono. ! Se si usa un subwoofer da 70 W (2 W), assicurarsi di collegarlo ai fili viola e viola/nero di questa unità. Non collegare niente ai fili verde e verde/nero. ! Le prestazioni ottimali si ottengono quando l’unità viene installata con un’angolazione inferiore a 60°. 60° Amplificatore di potenza (venduto a parte) Eseguire questi collegamenti quando si usa l’amplificatore opzionale. 3 1 5 2     4 5 1 Telecomando sistema Collegare al cavo Blu/bianco. 2 Amplificatore di potenza (venduto a parte) 3 Collegare con cavi RCA (venduti a parte) 4 All’uscita posteriore o del subwoofer 5 Altoparlanti posteriori o subwoofer ! Durante l’installazione, per assicurare la corretta dissipazione del calore quando si utilizza l’unità, accertarsi di lasciare ampio spazio dietro il pannello posteriore e avvolgere eventuali cavi allentati in modo che non ostruiscano le aperture. Lasciare ampio spazio 5 cm 5 cm 5cm cm Installazione Importante ! Controllare tutti i collegamenti e i sistemi prima dell’installazione finale. ! Non utilizzare componenti non approvati, poiché potrebbero provocare malfunzionamenti. ! Consultare il rivenditore se l’installazione richiede la trapanatura di fori o altre modifiche del veicolo. ! Non installare questa unità se: — potrebbe interferire con il funzionamento del veicolo. — potrebbe procurare lesioni al passeggero in caso di arresto improvviso del veicolo. ! Se si surriscalda il laser a semiconduttore potrebbe subire danni. Non installare questa unità in luoghi soggetti a surriscaldamento, come in prossimità delle bocchette dell’impianto di riscaldamento. Montaggio DIN anteriore/posteriore Questa unità può essere installata correttamente sia dalla posizione di montaggio anteriore, sia dalla posizione di montaggio posteriore. Durante l’installazione utilizzare componenti disponibili in commercio. Montaggio DIN anteriore 1 Inserire la fascetta di montaggio nel cruscotto. Se l’unità viene installata in uno spazio poco profondo, utilizzare la fascetta di montaggio fornita. Se dietro l’unità vi è spazio sufficiente, utilizzare la fascetta di montaggio fornita con il veicolo. It <QRD3143-C> 36 Black plate (37,1) Sezione Installazione Informazioni supplementari 2 Assicurare la fascetta di montaggio utilizzando un cacciavite per piegare le linguette metalliche (90°) in posizione. Rimozione dell’unità 1 1 2 Montaggio DIN posteriore 1 Determinare la posizione appropriata, in modo che i fori sulla staffa e sul lato dell’unità corrispondano. 2 Sintomo Causa Il display torna automaticamente alla visualizzazione normale. Non è stata ese- Eseguire nuovaguita alcuna mente l’operaziooperazione per ne. 30 secondi. L’intervallo di riproduzione ripetuta cambia imprevedibilmente. A seconda dell’intervallo di riproduzione ripetuta, l’intervallo selezionato potrebbe cambiare quando si seleziona una cartella o un brano diverso, o quando si procede all’avanzamento rapido/modalità inversa. Selezionare nuovamente l’intervallo di riproduzione ripetuta. I brani di una sottocartella non vengono riprodotti. Non è possibile riprodurre i brani delle sottocartelle se è selezionata l’opzione FLD (ripetizione della cartella). Selezionare un altro intervallo di riproduzione ripetuta. Quando cambia il display, viene visualizzata un’indicazione NO XXXX (ad esempio, NO TITLE). Nel brano non è incorporata alcuna informazione di testo. Modificare la visualizzazione o riprodurre un altro brano/file. 2 Inserire le chiavi di estrazione fornite su entrambi i lati dell’unità fino a che non scattano in posizione. 3 Estrarre l’unità dal cruscotto. Serrare due viti su ciascun lato. 3 1 2 1 Vite autofilettante (5 mm × 8 mm) 2 Staffa di montaggio 3 Cruscotto o console Rimozione e reinserimento del frontalino È possibile rimuovere il frontalino per proteggere l’unità dai furti. Premere il tasto di rimozione e spingere il frontalino verso l’alto tirandolo verso l’esterno. Per ulteriori dettagli, vedere Rimozione del frontalino per proteggere l’unità dai furti e Reinserimento del frontalino a pagina 30. Azione Sintomo Causa Azione Malfunzionamento dell’unità. Ci sono interferenze. Si sta utilizzando un dispositivo, ad esempio un cellulare, che trasmette onde elettromagnetiche in prossimità dell’unità. Spostare il dispositivo elettrico che causa interferenze lontano dall’unità. Messaggi di errore Se si contatta il rivenditore o il Centro assistenza Pioneer più vicino, accertarsi di annotare il messaggio di errore. Italiano 1 Guarnizione 2 Linguetta intaccata ! La rimozione del frontalino permette di accedere facilmente alla guarnizione. ! Quando si riapplica la guarnizione, spingere il lato con la linguetta intaccata verso il basso. 1 Cruscotto 2 Fascetta di montaggio # Accertarsi che l’unità sia saldamente installata in posizione. Un’installazione instabile potrebbe causare salti audio o altri malfunzionamenti. Risoluzione dei problemi Rimuovere la guarnizione. 03 Problemi comuni Messaggio Causa Azione AMP ERROR L’unità non funziona o l’altoparlante non è collegato correttamente; è stato attivato il circuito di protezione. Controllare il collegamento degli altoparlanti. Se il messaggio non scompare anche dopo aver disattivato e riattivato l’alimentazione, contattare il rivenditore o la stazione assistenza PIONEER più vicino. It <QRD3143-C> 37 37 Black plate (38,1) Appendice Informazioni supplementari Linee guida per l’uso corretto Lettore CD Messaggio Causa ERROR-07, Il disco è spor11, 12, 17, 30 co. ERROR-07, 10, 11, 12, 15, 17, 30, A0 ERROR-15 ERROR-23 FORMAT READ NO AUDIO SKIPPED PROTECT Informazioni supplementari Azione Dischi e lettori Pulire il disco. Il disco è graffiato. Sostituire il disco. Si è verificato un errore elettrico o meccanico. Spegnere e accendere il motore oppure passare a una sorgente diversa e poi di nuovo al lettore CD. Il disco inserito è vuoto. Sostituire il disco. Il formato del CD non è supportato. Sostituire il disco. Utilizzare esclusivamente dischi che riportino uno dei due seguenti loghi. La riproduzione dei dischi potrebbe non essere possibile a causa delle caratteristiche del disco, del formato del disco, dell’applicazione di registrazione, dell’ambiente di riproduzione, delle condizioni di conservazione e così via. Utilizzare dischi da 12 cm. Non utilizzare dischi da 8 cm o adattatori per dischi da 8 cm. Utilizzare esclusivamente dischi convenzionali, completamente circolari. Non utilizzare dischi dalla forma irregolare. A volte si verifi- Attendere che il ca ritardo tra messaggio scomquando la ripro- paia. duzione viene avviata e quando si inizia a percepire il suono. Nel vano d’inserimento dei CD non inserire nient’altro che CD. Il disco inserito Sostituire il disco. non contiene file riproducibili. Non è possibile riprodurre CD-R/RW non finalizzati. Il disco inserito contiene file protetti con tecnologia DRM. Sostituire il disco. Tutti i file nel disco inserito sono protetti da tecnologia DRM. Sostituire il disco. La formazione di condensa potrebbe temporaneamente limitare le prestazioni del lettore. In tal caso, lasciarlo raggiungere una temperatura più alta per circa un’ora. Inoltre, pulire i dischi che dovessero presentare condensa con un panno morbido. Non utilizzare dischi rotti, incrinati, piegati o altrimenti danneggiati, in quanto potrebbero danneggiare il lettore. Non toccare la superficie registrata dei dischi. Quando non si utilizzano, conservare i dischi nelle rispettive custodie. Non attaccare etichette, non scrivere e non applicare prodotti chimici sulla superficie dei dischi. Per pulire un CD, passare delicatamente un panno morbido sul disco procedendo dal centro verso l’esterno. Le asperità della strada possono far interrompere la riproduzione di un disco. Prima di utilizzare i dischi, leggere le relative avvertenze. Se si utilizzano dischi sui quali è possibile applicare etichette, controllare le istruzioni e le avvertenze dei dischi. L’inserimento e l’espulsione potrebbe non riuscire, a seconda dei dischi. L’uso di dischi di questo tipo potrebbe danneggiare questa unità. Non affiggere sui dischi etichette o altri materiali disponibili in commercio. ! I dischi potrebbero deformarsi e non sarà più possibile riprodurli. ! Le etichette potrebbero staccarsi durante la riproduzione, impedendo l’espulsione dei dischi. Ciò potrebbe danneggiare questa unità. Il caricamento e l’espulsione frequenti di un DualDisc, possono provocare la presenza di graffi sul disco. Graffi profondi possono determinare problemi di riproduzione sull’unità. In alcuni casi, il DualDisc potrebbe rimanere bloccato nel vano di inserimento disco e non essere espulso. Per prevenire questi inconvenienti, si consiglia di non utilizzare DualDisc con questa unità. Fare riferimento alle informazioni fornite dal produttore del disco per informazioni dettagliate sui DualDisc. Compatibilità audio compressa WMA Estensione file: .wma Velocità in bit: da 48 kbps a 320 kbps (CBR), da 48 kbps a 384 kbps (VBR) Frequenza di campionamento: 32 kHz, 44,1 kHz, 48 kHz Compatibilità Windows Media Audio Professional, Lossless, Voice/DRM Stream/Stream con video: non compatibile MP3 Estensione file: .mp3 DualDisc I supporti DualDisc sono dischi con due lati: un CD registrabile per l’audio su un lato e un DVD registrabile per i video sull’altro lato. Poiché il lato CD dei DualDisc non è fisicamente compatibile con gli standard CD generali, potrebbe non essere possibile riprodurre il lato CD con questa unità. Velocità in bit: da 8 kbps a 320 kbps (CBR), VBR Frequenza di campionamento: da 8 kHz a 48 kHz (32 kHz, 44,1 kHz, 48 kHz per l’enfatizzazione) Versioni tag ID3 compatibili: 1.0, 1.1, 2.2, 2.3, 2.4 (alla tag ID3 Versione 2.x viene data la priorità rispetto alla Versione 1.x.) Compatibilità lista di riproduzione m3u: non compatibile Compatibilità MP3i (MP3 interattivo), mp3 PRO: non compatibile 38 It <QRD3143-C> 38 Black plate (39,1) Appendice Informazioni supplementari WAV Informazioni supplementari Trasferimento dati con scrittura a pacchetti: non compatibile Estensione file: .wav Bit di quantizzazione lineare: 8 e 16 (LPCM), 4 (MS ADPCM) Frequenza di campionamento: da 16 kHz a 48 kHz (LPCM), 22,05 kHz e 44,1 kHz (MS ADPCM) Informazioni supplementari Il testo cirillico da visualizzare su questa unità deve essere codificato con uno dei seguenti set di caratteri: ! Unicode (UTF-8, UTF-16) ! Un set di caratteri diverso da Unicode utilizzato in ambiente Windows e impostato come cirillico nell’impostazione multilingue ATTENZIONE Non lasciare dischi in luoghi esposti ad alte temperature. File riproducibili: fino a 999 File system: ISO 9660 di livello 1 e 2, Romeo, Joliet Riproduzione multi-sessione: compatibile D: C D: C D: C :А :Б :В :Г :Д : Е, Ё :Ж :З : И, Й :К :Л :М :Н :О :П :Р :С :Т :У :Ф :Х :Ц :Ч : Ш, Щ :Ъ :Ы :Ь :Э :Ю :Я D: Display C: Carattere Con questa unità, l’utente non può assegnare i numeri alle cartelle e specificare sequenze di riproduzione. Copyright e marchi registrati Esempio di gerarchia Apple ed iTunes sono marchi di fabbrica di Apple Inc., registrati negli Stati Uniti ed in altri Paesi. 01 02 1 2 03 3 4 04 Disco Cartelle riproducibili: fino a 99 D: C Riproduzione in sequenza dei file audio A seconda dell’applicazione utilizzata per codificare i file WMA, questa unità potrebbe non funzionare correttamente. Gerarchia delle cartelle riproducibili: fino a otto livelli (una gerarchia pratica non dovrebbe prevedere più di due livelli.) D: C 5 6 05 Livello 1 Livello 2 Livello 3 Livello 4 : cartella : file audio compresso da 01 a 05: numero della cartella da 1 a 6: sequenza di riproduzione Disco La sequenza di selezione delle cartelle o altre operazioni potrebbero risultare differenti, a seconda del software utilizzato per la codifica o la scrittura. WMA Windows Media è un marchio di fabbrica o marchio di fabbrica depositato della Microsoft Corporation negli Stati Uniti ed in altri paesi. Questo prodotto include tecnologie di proprietà della Microsoft Corporation e non è utilizzbile senza licenza della Microsoft Licensing, Inc. Italiano Per i nomi dei file (incluse le estensioni) o i nomi delle cartelle, è possibile visualizzare esclusivamente i primi 32 caratteri. Indipendentemente dalla durata degli intervalli vuoti tra i brani della registrazione originale, i dischi contenenti file audio compresso verranno riprodotti con una breve pausa tra i brani. Tabella dei caratteri cirillici iTunes MP3 La fornitura di questo prodotto prevede il trasferimento di una licenza esclusivamente per uso privato, non-commerciale e non prevede la concessione di una licenza, né implica qualsiasi diritto a utilizzare questo prodotto in qualsiasi trasmissione in diretta commerciale (ovvero, che generi profitti) terrestre, via satellite, cavo e/ o tramite altro mezzo, trasmissioni/diffusioni tramite Internet, Intranet e/o altre reti o in altri sistemi elettronici di distribuzione di contenuti, come applicazioni di trasmissione audio a pagamento o audio-on-demand. Per tali usi è necessaria una licenza specifica. Per dettagli, visitare http://www.mp3licensing.com. It <QRD3143-C> 39 39 Black plate (40,1) Appendice Informazioni supplementari Dati tecnici Generali Alimentazione .................. 14,4 V di c.c. (variazioni consentite da 10,8 V a 15,1 V) Messa a terra ................... Negativa Consumo massimo .......... 10,0 A Dimensioni (L × A × P): DIN Unità principale ..................... 178 mm × 50 mm × 165 mm Pannello anteriore ..................... 188 mm × 58 mm × 16 mm D Unità principale ..................... 178 mm × 50 mm × 165 mm Pannello anteriore ..................... 170 mm × 46 mm × 16 mm Peso ................................ 1 kg Audio Potenza d’uscita massima ................................... 50 W × 4 70 W × 1/2 W (per il subwoofer) Potenza d’uscita continua ................................... 22 W × 4 (da 50 Hz a 15 000 Hz, 5% THD, carico 4 W, entrambi i canali) Impedenza di carico ......... 4 W (variazioni consentite da 4 W a 8 W) Livello massimo di uscita ................................... 2,0 V Contorno della sonorità .... +10 dB (a 100 Hz), +6,5 dB (a 10 kHz) (volume: –30 dB) Equalizzatore (equalizzatore grafico a 5 bande): Frequenza ................. 80 Hz/250 Hz/800 Hz/ 2,5 kHz/8 kHz Gamma di equalizzazione ............................ ±12 dB (a passi di 2 dB) Subwoofer (mono): Frequenze ................. 50 Hz/63 Hz/80 Hz/100 Hz/ 125 Hz/160 Hz/200 Hz Pendenza .................. –6 dB per ottava, –12 dB per ottava Guadagno ................. da +6 dB a –24 dB Fase .......................... Normale e invertita Lettore CD Sistema ........................... Sistema audio per compact disc Dischi utilizzabili .............. Compact disc Rapporto segnale/rumore ................................... 94 dB (a 1 kHz) (rete IEC-A) Numero di canali ............. 2 (stereo) Formato di decodifica MP3 ................................... MPEG-1 & 2 Audio Layer 3 Formato di decodifica WMA ................................... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2 canali audio) (Windows Media Player) Formato segnale WAV ...... PCM lineare & MS ADPCM (Non compresso) Sintonizzatore FM Gamma di frequenze ........ da 87,5 MHz a 108,0 MHz Sensibilità ........................ 9 dBf (0,8 µV/75 W, mono, rapporto S/R: 30 dB) Rapporto segnale/rumore ................................... 72 dB (rete IEC-A) Sintonizzatore MW Gamma di frequenze ........ da 531 kHz a 1 602 kHz Sensibilità ........................ 25 µV (rapporto S/R: 20 dB) Rapporto segnale/rumore ................................... 62 dB (rete IEC-A) Sintonizzatore LW Gamma di frequenze ........ da 153 kHz a 281 kHz Sensibilità ........................ 28 µV (rapporto S/R: 20 dB) Rapporto segnale/rumore ................................... 62 dB (rete IEC-A) Nota Caratteristiche tecniche e design sono soggetti a eventuali modifiche senza preavviso. 40 It <QRD3143-C> 40 Black plate (41,1) Italiano It <QRD3143-C> 41 41 Black plate (42,1) Sección Antes de comenzar 01 Gracias por haber adquirido este producto PIONEER Lea con detenimiento este manual antes de utilizar el producto por primera vez para que pueda darle el mejor uso posible. Es muy importante que lea y cumpla con la información que aparece bajo los mensajes de ADVERTENCIA y PRECAUCIÓN de este manual. Una vez leído, guarde el manual en un lugar seguro y a mano para poder consultarlo en el futuro. Antes de comenzar Acerca de esta unidad En caso de problemas Las frecuencias del sintonizador de esta unidad están asignadas para su uso en Europa Occidental, Asia, Oriente Próximo, África y Oceanía. El uso en otras áreas puede causar una recepción deficiente. La función RDS (sistema de datos de radio) opera solo en áreas con emisoras de FM que trasmitan señales de RDS. Si esta unidad no funcionase correctamente, póngase en contacto con su concesionario o con el centro de servicio PIONEER autorizado más cercano. PRECAUCIÓN Este aparato es un producto de láser de clase 1 clasificado como tal en Seguridad de productos de láser, IEC 60825-1:2007. PRODUCTO LASER CLASE 1 Si desea deshacerse de este producto, no lo mezcle con los residuos generales de su hogar. De conformidad con la legislación vigente, existe un sistema de recogida distinto para los productos electrónicos que requieren un procedimiento adecuado de tratamiento, recuperación y reciclado. Las viviendas privadas en los estados miembros de la UE, en Suiza y Noruega pueden devolver gratuitamente sus productos electrónicos usados en los centros de recolección previstos o bien en una tienda minorista (si adquieren un producto similar nuevo). En el caso de los países que no se han mencionado en el párrafo anterior, póngase en contacto con las autoridades locales a fin de conocer el método de eliminación correcto. Al actuar siguiendo estas instrucciones, se asegurará de que el producto eliminado se someta a los procesos de tratamiento, recuperación y reciclaje necesarios, evitando de este modo efectos potencialmente negativos en el entorno y la salud humana. 42 PRECAUCIÓN ! Evite que esta unidad entre en contacto con líquidos, ya que puede producir una descarga eléctrica. Además, el contacto con líquidos puede causar daños en la unidad, humo y recalentamiento. ! El CarStereo-Pass de Pioneer solo debe usarse en Alemania. ! Mantenga siempre el volumen lo suficientemente bajo como para poder escuchar los sonidos que provienen del exterior. ! Evite la exposición a la humedad. ! Si se desconecta o se descarga la batería, todas las memorias preajustadas se borrarán. Nota Las operaciones se realizan incluso si se cancela el menú antes de confirmar. Es <QRD3143-C> 42 Black plate (43,1) Sección Utilización de esta unidad Utilización de esta unidad Unidad principal Indicador 1 2 34 5 6 7 8 9 a 1 b Parte c d 8 BAND 2 SRC/OFF 9 (parte posterior)/DIMMER (reductor de luz) 3 MULTI-CONTROL (M.C.) a c/d b 1/ 4 (lista) 3 TA (anuncios de tráfico) La función TA está activada. 4 TP (identificación de programa de tráfico) Una emisora TP está sintonizada. 5 5 DISP c 6 Ranura de carga de discos d Botón de soltar 6 7 8 Indicaciones de la pantalla 2 3 9 4 5 (repetición) (aleatorio) La función recuperación de sonido está activada. Sintonización por búsqueda local activada. La repetición de pista o carpeta está activada. La reproducción aleatoria está activada. 9 a Aparece cuando existe un nivel, carpeta o menú inferior. 6 8 7 a LOC Una vez instalada la unidad, al poner en ON la llave de encendido aparecerá el menú de configuración. Se pueden configurar las opciones del menú que se describen a continuación. 1 Una vez instalada la unidad, gire la llave de encendido hasta la posición ON. Aparecerá SET UP. 2 ! Sintonizador: banda y frecuencia ! RDS: nombre del servicio Sección de del programa, informainformación ción PTY y otro tipo de inprincipal formación de texto ! Lector de CD: tiempo de reproducción transcurrido e información de texto (ecualizador) 1 (recuperador de sonido) a 6/ Conector de entrada AUX (conector estéreo de 3,5 mm) 7 Sección de Muestra la información seinformación cundaria. secundaria Menú de configuración Pulse M.C. para cambiar a YES. # El menú de configuración desaparecerá si no se utiliza la unidad durante 30 segundos. # Si prefiere dejar la configuración para más tarde, gire M.C. para cambiar a NO y púlselo para realizar la selección. Si selecciona NO, no podrá realizar cambios en el menú de configuración. 3 Pulse M.C. para seleccionarlo. 4 Siga los siguientes pasos para ajustar el menú: Para avanzar a la siguiente opción del menú debe confirmar primero su selección. LANGUAGE (idiomas múltiples) Esta unidad puede mostrar la información de texto de un archivo de audio comprimido incluso para aquella información integrada en inglés o ruso. ! Si el idioma integrado y el idioma seleccionado no coinciden, puede que la información de texto no se muestre correctamente. ! Es posible que algunos caracteres no se visualicen correctamente. 1 Gire M.C. para seleccionar el ajuste deseado. ENG (Inglés)—РУС (Ruso) 2 Pulse M.C. para confirmar la selección. CLOCK SET (ajuste del reloj) 1 2 3 4 Gire M.C. para ajustar el volumen. Presione M.C. para seleccionar el minuto. Gire M.C. para ajustar el minuto. Pulse M.C. para confirmar la selección. FM STEP (paso de sintonía de FM) Normalmente, el paso de sintonía de FM empleado en la sintonización por búsqueda es de 50 kHz. Si la función AF o TA está activada, el paso de sintonía cambia automáticamente a 100 kHz. Puede que convenga ajustar el paso de sintonía a 50 kHz si la función AF está activada. ! El paso de sintonía se mantiene en 50 kHz durante la sintonización manual. 1 Gire M.C. para seleccionar el paso de sintonía de FM. 50 (50 kHz)—100 (100 kHz) 2 Pulse M.C. para confirmar la selección. Aparecerá QUIT. Español h (expulsar) Se está utilizando la función de la lista. 2 Parte 1 (lista) Estado 02 5 Para cerrar la configuración, gire M.C. y seleccione YES. # Si prefiere volver a cambiar la configuración, gire M.C. para cambiar a NO y púlselo para realizar la selección. 6 Pulse M.C. para seleccionarlo. Notas ! Se pueden configurar las opciones del menú desde el menú del sistema. Si desea más información sobre los ajustes, consulte Menú del sistema en la página 47. ! Si desea cancelar el menú de configuración, pulse SRC/OFF. Funcionamiento básico Importante ! Proceda con cuidado al retirar o colocar el panel delantero. Es <QRD3143-C> 43 43 Black plate (44,1) Sección Utilización de esta unidad 02 ! Evite someter el panel delantero a impactos excesivos. ! Mantenga el panel delantero alejado de la luz solar directa y no lo exponga a altas temperaturas. ! Para evitar que el dispositivo o el interior del vehículo sufran daños, retire todos los cables o dispositivos conectados al panel delantero antes de extraerlo. Utilización de esta unidad Extracción del panel delantero para proteger la unidad contra robo 1 Pulse el botón de soltar para liberar el panel delantero. 2 Empuje el panel delantero hacia arriba (M) y tire de él hacia usted (N). Selección de una fuente 1 Pulse SRC/OFF para desplazarse entre: TUNER (sintonizador)—CD (reproductor de CD)—AUX (AUX) Ajuste del volumen 1 Gire M.C. para ajustar el volumen. PRECAUCIÓN Por motivos de seguridad, detenga el vehículo antes de extraer el panel delantero. 3 Mantenga siempre el panel delantero que se ha extraído en su medio de protección, como la caja protectora. Colocación del panel delantero 1 Deslice el panel hacia la izquierda. Inserte las pestañas que hay en la parte izquierda de la unidad principal dentro de las ranuras del panel delantero. 2 Pulse el lado derecho del panel delantero hasta que se asiente firmemente. Si no logra encajar adecuadamente el panel delantero a la unidad principal, colóquelo de la forma correcta; no apriete ni use la fuerza para encajarlo, ya que puede provocar daños en el mismo o en la unidad principal. Encendido de la unidad 1 Pulse SRC/OFF para encender la unidad. Apagado de la unidad 1 Mantenga pulsado SRC/OFF hasta que se apague la unidad. 44 Nota Si el cable azul/blanco de esta unidad está conectado al terminal de control del relé de la antena automática del vehículo, la antena se extenderá cuando se encienda el equipo. Para retraer la antena, apague la fuente. Operaciones del menú utilizadas frecuentemente Retorno a la visualización anterior Para volver a la lista anterior (la carpeta de un nivel superior) 1 Pulse /DIMMER. Retorno a la visualización normal Acceso al menú principal 1 Pulse BAND. Retorno a la visualización normal desde la lista 1 Pulse BAND. Sintonizador Funcionamiento básico Selección de una banda 1 Pulse BAND hasta que se visualice la banda deseada (FM1, FM2, FM3 para FM o MW/ LW). Cambio de emisoras presintonizadas 1 Pulse c o d. ! Para utilizar esta función, seleccione PCH (canal presintonizado) en SEEK. Para obtener más información sobre la configuración, consulte SEEK (ajuste tecla izquierda/derecha) en la página siguiente. Sintonización manual (paso a paso) 1 Pulse c o d. ! Para utilizar esta función, seleccione MAN (sintonización manual) en SEEK. Para obtener más información sobre la configuración, consulte SEEK (ajuste tecla izquierda/derecha) en la página siguiente. Búsqueda 1 Mantenga pulsado c o d y luego suéltelo. Se puede cancelar la sintonización por búsqueda pulsando brevemente c o d. Mientras mantiene pulsado c o d se pueden saltar las emisoras. La sintonización por búsqueda comienza inmediatamente después de que suelte c o d. Nota Se puede activar y desactivar la función AF (búsqueda de frecuencias alternativas) de esta unidad; se debe desactivar la función AF para la sintonización normal (consulte AF (búsqueda de frecuencias alternativas) en la página siguiente). Es <QRD3143-C> 44 Black plate (45,1) Sección Utilización de esta unidad Almacenamiento y recuperación de emisoras para cada banda Uso de los botones de ajuste de presintonías 1 Cuando encuentre la emisora que desee almacenar en la memoria, pulse uno de los botones de ajuste de presintonías (1/ a 6/ ) y manténgalo pulsado hasta que el número de presintonía deje de parpadear. 2 Pulse uno de los botones de ajuste de presintonías (1/ a 6/ ) para seleccionar la emisora deseada. Cambio de la visualización Notas ! Si no se puede adquirir el nombre del servicio de programa en FREQUENCY, se visualizará la frecuencia en su lugar. Si se detecta el nombre del servicio de programa, se visualizará el nombre del servicio de programa. ! BRDCST INFO la información de texto cambiará automáticamente. ! Dependiendo de la banda, puede cambiarse la información de texto. ! Los elementos de información de texto pueden cambiar según la zona. Uso de las funciones PTY Se puede sintonizar una emisora utilizando la información PTY (tipo de programa). Búsqueda de una emisora RDS por información PTY Se pueden buscar programas de tipo general, como los que se indican en el apartado siguiente. Consulte esta página. (lista). 1 Pulse 2 Gire M.C. para seleccionar el tipo de programa. NEWS/INFO—POPULAR—CLASSICS—OTHERS 3 Pulse M.C. para comenzar la búsqueda. La unidad busca una emisora que transmita ese tipo de programa, cuando la encuentra, se visualiza el nombre del servicio de programa. ! Para cancelar la búsqueda, vuelva a pulsar M.C. ! El programa de algunas emisoras puede ser distinto al programa indicado por el PTY transmitido. ! Si ninguna emisora está transmitiendo el tipo de programa que busca, se visualizará NOT FOUND durante unos dos segundos y el sintonizador volverá a la emisora original. Lista PTY NEWS/INFO (noticias e información) NEWS (noticias), AFFAIRS (temas de actualidad), INFO (información), SPORT (programas deportivos), WEATHER (tiempo), FINANCE (finanzas) POPULAR (popular) POP MUS (música popular), ROCK MUS (rock), EASY MUS (música ligera), OTH MUS (otras músicas), JAZZ (jazz), COUNTRY (música country), NAT MUS (música nacional), OLDIES (música antigua), FOLK MUS (música folclórica) OTHERS (otros) EDUCATE (educación), DRAMA (drama), CULTURE (cultura), SCIENCE (ciencia), VARIED (variedades), CHILDREN (programas para niños), SOCIAL (temas sociales), RELIGION (religión), PHONE IN (entrada por teléfono), TOURING (viajes), LEISURE (ocio), DOCUMENT (documentales) Ajustes de funciones 1 Pulse M.C. para acceder al menú principal. 2 Gire M.C. para cambiar la opción de menú y pulse para seleccionar FUNCTION. 02 La sintonización por búsqueda local le permite sintonizar solo las emisoras de radio con señales lo suficientemente intensas como para asegurar una correcta recepción. 1 Pulse M.C. para seleccionar el ajuste deseado. FM: OFF—LV1—LV2—LV3—LV4 MW/LW: OFF—LV1—LV2 El ajuste de nivel superior solo permite recibir las emisoras con las señales más intensas, mientras que los ajustes más bajos permiten recibir las emisoras con señales más débiles. TA (espera por anuncio de tráfico) 1 Pulse M.C. para activar o desactivar la espera por anuncio de tráfico. AF (búsqueda de frecuencias alternativas) 3 Gire M.C. para seleccionar la función. Una vez seleccionado, se pueden ajustar las siguientes funciones. # Si se selecciona la banda MW/LW, solo estarán disponibles BSM, LOCAL y SEEK. BSM (memoria de las mejores emisoras) BSM (memoria de las mejores emisoras) guarda automáticamente las seis emisoras más fuertes ordenadas por la intensidad de la señal. 1 Pulse M.C. para activar la función BSM. Para cancelar, vuelva a pulsar M.C. REGION (regional) Cuando se usa la función AF, la función regional limita la selección de las emisoras a aquellas que transmiten programas regionales. 1 Pulse M.C. para activar o desactivar la función regional. 1 Pulse M.C. para activar o desactivar la función AF. NEWS (interrupción por programa de noticias) 1 Pulse M.C. para activar o desactivar la función NEWS. Español Selección de la información de texto deseada 1 Pulse DISP para desplazarse entre las siguientes opciones: ! FREQUENCY (nombre del servicio de programa o frecuencia) ! BRDCST INFO (nombre del servicio de programa/información PTY) ! CLOCK (nombre de la fuente y reloj) Utilización de esta unidad SEEK (ajuste tecla izquierda/derecha) Es posible asignar funciones a las teclas derecha e izquierda de la unidad. Seleccione MAN (sintonización manual) para subir o bajar la frecuencia de forma manual o seleccione PCH (canales presintonizados) para cambiar entre los canales presintonizados. 1 Presione M.C. para seleccionar MAN o PCH. LOCAL (sintonización por búsqueda local) CLASSICS (clásicos) L. CLASS (música clásica ligera), CLASSIC (clásica) Es <QRD3143-C> 45 45 Black plate (46,1) Sección Utilización de esta unidad 02 CD/CD-R/CD-RW Funcionamiento básico Reproducción de un CD/CD-R/CD-RW 1 Inserte el disco en la ranura de carga de discos con el lado de la etiqueta hacia arriba. Expulsión de un CD/CD-R/CD-RW 1 Pulse h. Selección de una carpeta 1 Pulse 1/ o 2/ . Selección de una pista 1 Pulse c o d. Avance rápido o retroceso 1 Mantenga pulsado c o d. ! Al reproducir audio comprimido, no hay sonido durante el avance rápido o el retroceso. Regreso a la carpeta raíz 1 Mantenga BAND pulsado. Cambio entre audio comprimido y CD-DA 1 Pulse BAND. Utilización de esta unidad Cambio de la visualización Selección de la información de texto deseada 1 Pulse DISP para desplazarse entre las siguientes opciones: CD-DA ! ELAPSED TIME (número de pista y tiempo de reproducción) ! CLOCK (nombre de la fuente y reloj) ! SPEANA (analizador de espectro) CD-TEXT ! TRACK INFO (título de la pista/artista de la pista/título del disco) ! ELAPSED TIME (número de pista y tiempo de reproducción) ! CLOCK (nombre de la fuente y reloj) ! SPEANA (analizador de espectro) MP3/WMA/WAV ! TRACK INFO (título de la pista/nombre del artista/título del álbum) ! FILE INFO (nombre del fichero/nombre de la carpeta) ! ELAPSED TIME (número de pista y tiempo de reproducción) ! CLOCK (nombre de la fuente y reloj) ! SPEANA (analizador de espectro) Notas ! TRACK INFO y FILE INFO la información de texto cambiará automáticamente. ! Según la versión de iTunes utilizada para grabar archivos MP3 en un disco u otro tipo de archivo de medios, es posible que los textos contenidos en el archivo de audio no se muestren correctamente si su formato es incompatible. ! Los elementos de información de texto pueden cambiar según el tipo de medio. 46 Selección y reproducción de archivos/pistas de la lista de nombres 1 Pulse para cambiar al modo de lista por nombre de archivo/pista. 2 Utilice M.C. para seleccionar el nombre del archivo deseado (o de la carpeta). Selección de un archivo o una carpeta 1 Gire M.C. Reproducción 1 Tras seleccionar un archivo o una pista, pulse M.C. Visualización de una lista de los archivos (o las carpetas) de la carpeta seleccionada 1 Tras seleccionar una carpeta, pulse M.C. Reproducción de una canción de la carpeta seleccionada 1 Tras seleccionar una carpeta, mantenga pulsado M.C. Operaciones con botones especiales Selección de un intervalo de repetición de reproducción 1 Pulse 6/ para desplazarse entre las siguientes opciones: ! ALL – Repite todas las pistas ! ONE – Repite la pista actual ! FLD – Repite la carpeta actual Reproducción de las pistas en orden aleatorio para activar o desactivar la repro1 Pulse 5/ ducción aleatoria. Las pistas de una gama de repetición seleccionada se reproducen en orden aleatorio. ! Para cambiar de canciones durante la reproducción aleatoria, pulse d para cambiar a la pista siguiente; si se pulsa c se reiniciará la reproducción de la pista actual desde el principio de la canción. Pausa de la reproducción 1 Pulse 4/PAUSE para pausar o reanudar. Mejora del audio comprimido y restauración del sonido óptimo (Sound Retriever) 1 Pulse 3/S.Rtrv para desplazarse entre: 1—2—OFF (desactivado) 1 es efectivo para tasas de compresión baja, y 2 para tasas de compresión alta. Ajustes de funciones 1 Pulse M.C. para acceder al menú principal. 2 Gire M.C. para cambiar la opción de menú y pulse para seleccionar FUNCTION. Una vez seleccionado, se puede ajustar la función de abajo. Es <QRD3143-C> 46 Black plate (47,1) Sección Utilización de esta unidad Utilización de esta unidad S.RTRV (recuperador de sonido) FADER (ajuste de ecualizador) Mejora automáticamente el audio comprimido y restaura el sonido óptimo. 1 Pulse M.C. para seleccionar el ajuste deseado. Para obtener más información, consulte Mejora del audio comprimido y restauración del sonido óptimo (Sound Retriever) en la página anterior. 1 Pulse M.C. para mostrar el modo de ajuste. 2 Gire M.C. para ajustar el balance entre los altavoces delanteros/traseros. BALANCE (ajuste del balance) 1 Pulse M.C. para mostrar el modo de ajuste. 2 Gire M.C. para ajustar el balance de los altavoces izquierdo o derecho. EQ SETTING (recuperación de ecualizador) 1 Pulse M.C. para acceder al menú principal. 1 Pulse M.C. para mostrar el modo de ajuste. 2 Gire M.C. para seleccionar el ecualizador. POWERFUL—NATURAL—VOCAL—CUSTOM1—CUSTOM2—FLAT—SUPER BASS La banda y el nivel de ecualización se pueden personalizar si se selecciona CUSTOM1 o CUSTOM2. Si selecciona CUSTOM1 o CUSTOM2, complete los pasos que se describen más abajo. Si selecciona otras opciones, pulse M.C. para volver a la pantalla anterior. ! CUSTOM1 puede ajustarse por separado para cada fuente. ! CUSTOM2 es una configuración compartida que se utiliza para todas las fuentes. 3 Pulse M.C. para mostrar el modo de ajuste. 4 Pulse M.C. para desplazarse entre las siguientes opciones: Banda de ecualización—Nivel de ecualización 5 Gire M.C. para seleccionar el ajuste deseado. Banda de ecualización: 80HZ—250HZ— 800HZ—2.5KHZ—8KHZ Nivel de ecualización: +6 a –6 ! También puede cambiar el ecualizador pulsan. do varias veces 2 Gire M.C. para cambiar la opción de menú y pulse para seleccionar AUDIO. 3 Gire M.C. para seleccionar la función de audio. Una vez seleccionado, se pueden ajustar las siguientes funciones de audio. ! FADER no está disponible cuando se selecciona SUB.W/SUB.W en SP-P/O MODE. Para más información, consulte SP-P/O MODE (ajuste de la salida posterior y del preamplificador) en la página siguiente. ! SUB.W, SUB.W CTRL, HPF SETTING no están disponibles cuando se selecciona REAR/REAR en SP-P/O MODE. Para más información, consulte SP-P/O MODE (ajuste de la salida posterior y del preamplificador) en la página siguiente. ! SUB.W CTRL y HPF SETTING no están disponibles cuando se selecciona SUB.W en OFF. Para más información, consulte SUB.W (ajuste de subgraves activado/desactivado) en esta página. LOUDNESS (sonoridad) SUB.W (ajuste de subgraves activado/desactivado) Esta unidad está equipada con una salida de subgraves que se puede activar o desactivar. 1 Pulse M.C. para seleccionar el ajuste deseado. NOR (fase normal)—REV (fase inversa)—OFF (subgraves desactivados) SUB.W CTRL (ajuste de subgraves) Solo las frecuencias más bajas que aquellas en el intervalo seleccionado se generan por el altavoz de subgraves. 1 Pulse M.C. para mostrar el modo de ajuste. 2 Pulse M.C. para desplazarse entre las siguientes opciones: Frecuencia de corte—Nivel de salida—Nivel de pendiente Las tasas que se puedan ajustar parpadearán. 3 Gire M.C. para seleccionar el ajuste deseado. Frecuencia de corte: 50HZ—63HZ—80HZ— 100HZ—125HZ—160HZ—200HZ Nivel de salida: de –24 a +6 Nivel de pendiente: –6— –12 Cuando no desee que se generen los sonidos bajos del intervalo de frecuencias de salida de subgraves a través de los altavoces delanteros o traseros, active el filtro de paso alto (HPF). Solo las frecuencias más altas que aquellas del intervalo seleccionado se generan a través de los altavoces delanteros o traseros. 1 Pulse M.C. para mostrar el modo de ajuste. 2 Pulse M.C. para desplazarse entre las siguientes opciones: Frecuencia de corte—Nivel de pendiente 3 Gire M.C. para seleccionar el ajuste deseado. Frecuencia de corte: OFF—50HZ—63HZ— 80HZ—100HZ—125HZ—160HZ—200HZ Nivel de pendiente: –6— –12 SLA (ajuste del nivel de fuente) SLA (ajuste del nivel de fuente) le permite ajustar el nivel de volumen de cada fuente para evitar cambios radicales en el volumen cuando se cambia entre las fuentes. ! Los ajustes se basan en el nivel de volumen de FM, que se mantiene inalterado. ! El nivel del volumen de MW/LW también se puede ajustar con esta función. ! Al seleccionar FM como fuente, no se podrá cambiar a SLA. 1 Pulse M.C. para mostrar el modo de ajuste. 2 Gire M.C. para ajustar el volumen de la fuente. Gama de ajuste: de +4 a –4 Español Ajustes de audio La sonoridad compensa las deficiencias en los intervalos de frecuencias bajas y altas cuando se escucha a un volumen bajo. 1 Pulse M.C. para seleccionar el ajuste deseado. OFF (desactivado)—LOW (bajo)—MID (medio)—HI (alto) 02 BASS BOOST (intensificación de graves) 1 Pulse M.C. para mostrar el modo de ajuste. 2 Gire M.C. para seleccionar el nivel que desee. Se visualiza 0 a +6 mientras se aumenta o disminuye el nivel. HPF SETTING (ajuste del filtro de paso alto) Menú del sistema Importante PW SAVE (ahorro de energía) se cancela si la batería del vehículo se desconecta, y se debe activar de nuevo cuando se vuelva a conectar la batería. Dependiendo de los métodos de conexión, cuando PW SAVE (ahorro de energía) está desactivado, la unidad puede seguir obteniendo energía de la batería si la llave de encendido de su vehículo no tiene posición ACC (accesorio). Es <QRD3143-C> 47 47 Black plate (48,1) Sección Utilización de esta unidad 02 1 Pulse M.C. para acceder al menú principal. 2 Gire M.C. para cambiar la opción de menú y pulse para seleccionar SYSTEM. 3 Gire M.C. para seleccionar la función del menú del sistema. Una vez seleccionado, se pueden ajustar las siguientes funciones del menú de sistema. LANGUAGE (idiomas múltiples) Esta unidad puede mostrar la información de texto de un archivo de audio comprimido incluso para aquella información integrada en inglés o ruso. ! Si el idioma integrado y el idioma seleccionado no coinciden, puede que la información de texto no se muestre correctamente. ! Es posible que algunos caracteres no se visualicen correctamente. 1 Gire M.C. para seleccionar el ajuste deseado. ENG (Inglés)—РУС (Ruso) CLOCK SET (ajuste del reloj) 1 Pulse M.C. para mostrar el modo de ajuste. 2 Pulse M.C. para seleccionar el segmento de la pantalla del reloj que desea ajustar. Hora—Minuto 3 Gire M.C. para ajustar el reloj. 12H/24H (anotación de la hora) 1 Pulse M.C. para seleccionar el ajuste deseado. 12H (reloj de 12 horas)—24H (reloj de 24 horas) AUTO PI (búsqueda PI automática) Utilización de esta unidad La unidad puede buscar automáticamente una emisora diferente con el mismo programa, incluso durante la recuperación de emisoras presintonizadas. 1 Pulse M.C. para activar o desactivar la función de búsqueda PI automática. AUX (entrada auxiliar) Active este ajuste si utiliza un dispositivo auxiliar conectado a esta unidad. 1 Pulse M.C. para activar o desactivar AUX. MUTE MODE (modo de silencio) El sonido proveniente de este sistema se silencia o atenúa automáticamente cuando se recibe una señal desde un equipo con función de silenciamiento. 1 Pulse M.C. para mostrar el modo de ajuste. 2 Gire M.C. para seleccionar el ajuste deseado. Se puede seleccionar cualquiera de las opciones de la lista siguiente: ! MUTE – Silenciamiento ! 20dB ATT – Atenuación (20dB ATT tiene un efecto más potente que 10dB ATT) ! 10dB ATT – Atenuación PW SAVE (ahorro de energía) La activación de esta función le permite reducir el consumo de la batería. ! Cuando esta función está activada, la única operación que se permite es el encendido de la fuente. 1 Pulse M.C. para activar o desactivar el ahorro de energía. Cambio del ajuste del atenuador de luz Puede ajustar el brillo de la iluminación. 2 Gire M.C. para visualizar ILLUMI y púlselo para realizar la selección. 3 Pulse M.C. para seleccionar el ajuste deseado. OFF (activado)—ON (desactivado) ! También se puede cambiar la configuración de atenuador de luz manteniendo pulsado /DIMMER. Menú inicial 1 Mantenga pulsado SRC/OFF hasta que se apague la unidad. 2 Mantenga pulsado SRC/OFF hasta que aparezca el menú principal en la pantalla. 3 Gire M.C. para cambiar la opción de menú y pulse para seleccionar INITIAL. 4 Gire M.C. para seleccionar la función del menú de inicio. Una vez seleccionado, se pueden ajustar las siguientes funciones del menú inicial. FM STEP (paso de sintonía de FM) Normalmente, el paso de sintonía de FM empleado en la sintonización por búsqueda es de 50 kHz. Si la función AF o TA está activada, el paso de sintonía cambia automáticamente a 100 kHz. Puede que convenga ajustar el paso de sintonía a 50 kHz si la función AF está activada. ! El paso de sintonía se mantiene en 50 kHz durante la sintonización manual. 1 Pulse M.C. para seleccionar el paso de sintonía de FM. 50 (50 kHz)—100 (100 kHz) SP-P/O MODE (ajuste de la salida posterior y del preamplificador) La salida de cables de altavoces traseros y la salida RCA de esta unidad se puede usar para conectar altavoces de gama completa o de subgraves. Seleccione la opción adecuada para su conexión. 1 Pulse M.C. para mostrar el modo de ajuste. 2 Gire M.C. para seleccionar el ajuste deseado. Se puede seleccionar cualquiera de las opciones de la lista siguiente: ! REAR/SUB.W – Seleccione cuando haya conectado un altavoz de gama completa a la salida de cables de altavoces traseros y un subgrave a la salida RCA. ! SUB.W/SUB.W – Seleccione cuando haya conectado un subgrave directamente a la salida de cables de altavoces traseros, sin ningún amplificador auxiliar, y un subgrave a la salida RCA. ! REAR/REAR – Seleccione cuando exista un altavoz de gama completa conectado a la salida de cables de los altavoces traseros y a la salida RCA. Si hay un altavoz de gama completa conectado a la salida de cables de los altavoces traseros y la salida RCA no se utiliza, podrá seleccionar REAR/SUB.W o REAR/REAR. Menú del sistema 1 Mantenga pulsado SRC/OFF hasta que se apague la unidad. 2 Mantenga pulsado SRC/OFF hasta que aparezca el menú principal en la pantalla. 3 Gire M.C. para cambiar la opción de menú y pulse para seleccionar SYSTEM. 1 Pulse M.C. para acceder al menú principal. 48 Es <QRD3143-C> 48 Black plate (49,1) Sección Utilización de esta unidad Instalación 02 03 4 Gire M.C. para seleccionar la función del menú del sistema. Una vez seleccionado, se pueden ajustar las siguientes funciones del menú de sistema. Para obtener más información, consulte Menú del sistema en la página 47. Uso de una fuente AUX 3 Gire M.C. para visualizar DEMO OFF y púlselo para realizar la selección. 4 Pulse M.C. para cambiar a YES. 5 Pulse M.C. para seleccionarlo. Conexiones Importante ! Cuando esta unidad se instale en un vehículo sin posición ACC (accesorio) en la llave de encendido, el cable rojo se debe conectar al terminal que pueda detectar la operación de la llave de encendido. De lo contrario, puede descargarse la batería. OF F O N 1 Inserte el miniconector estéreo en el conector de entrada AUX. T Cambio de la visualización Selección de la información de texto deseada 1 Pulse DISP para desplazarse entre las siguientes opciones: ! Nombre de la fuente ! Nombre de la fuente y reloj Si aparece un display no deseado Desactive el display no deseado mediante los pasos que se indican a continuación. 1 Pulse M.C. para acceder al menú principal. 2 Gire M.C. para cambiar la opción de menú y pulse para seleccionar SYSTEM. Posición ACC Sin posición ACC ! El uso de esta unidad en unas condiciones distintas de las indicadas a continuación podría causar incendios o fallos de funcionamiento. — Vehículos con una batería de 12 voltios y conexión a tierra negativa. — Altavoces con 50 W (valor de salida) y 4 W a 8 W (valor de impedancia). ! Para evitar cortocircuitos, sobrecalentamiento o fallos de funcionamiento, asegúrese de seguir las siguientes instrucciones. — Desconecte el terminal negativo de la batería antes de la instalación. — Asegure el cableado con pinzas para cables o cinta adhesiva. Envuelva con cinta adhesiva las partes en contacto con piezas metálicas para proteger el cableado. — Mantenga los cables alejados de las partes móviles, como la palanca de cambios y los raíles de los asientos. — Coloque todos los cables alejados de lugares calientes, como cerca de la salida del calefactor. — No conecte el cable amarillo a la batería pasándolo a través del orificio hasta el compartimiento del motor. — Cubra con cinta aislante los conectores de cables que queden desconectados. — No acorte ningún cable. ! Cuando se enciende esta unidad, se emite una señal de control a través del cable azul/ blanco. Conecte este cable al mando a distancia del sistema de un amplificador de potencia externo o al terminal de control del relé de la antena automática del vehículo (máx. 300 mA 12 V cc). Si el vehículo posee una antena integrada en el cristal del parabrisas, conéctela al terminal de la fuente de alimentación del amplificador de la antena. ! Nunca conecte el cable azul/blanco al terminal de potencia de un amplificador de potencia externo, ni al terminal de potencia de la antena automática, de lo contrario, puede descargarse la batería o producirse un fallo de funcionamiento. ! El cable negro es el cable a tierra. Los cables a tierra de esta unidad y de otros productos (especialmente productos de alta tensión, como amplificadores de potencia) se deben conectar por separado, de lo contrario, puede producirse un incendio o un fallo de funcionamiento si se desconectan por accidente. Español Nota No se puede seleccionar AUX si no se activa el ajuste auxiliar. Para obtener más información, consulte AUX (entrada auxiliar) en la página anterior. STAR 2 Pulse SRC/OFF para seleccionar AUX como fuente. — Nunca corte el aislamiento del cable de alimentación de esta unidad para compartir la corriente con otros equipos. La capacidad de corriente del cable es limitada. — Utilice un fusible con la intensidad nominal indicada. — Nunca conecte el cable negativo de los altavoces directamente a tierra. — Nunca empalme los cables negativos de varios altavoces. Esta unidad 1 3 4 2 5 1 Entrada del cable de alimentación Es <QRD3143-C> 49 49 Black plate (50,1) Sección Instalación 03 2 3 4 5 Instalación Salida trasera o salida de subgraves Entrada de la antena Fusible (10 A) Entrada remota conectada Es posible conectar un adaptador de mando a distancia físicamente conectado (se vende por separado). Cable de alimentación 3 4 5 2 7 1 6 3 4 5 6 8 a 9 e b c d 1 A la toma del cable de alimentación 2 Según el tipo de vehículo, las funciones de 3 y 5 pueden ser diferentes. En este caso, conecte 4 a 5 y 6 a 3. 3 Amarillo Reserva (o accesorio) 4 Amarillo Conectar al terminal de alimentación constante de 12 V. 5 Rojo Accesorio (o reserva) 6 Rojo Conectar al terminal controlado por la llave de encendido (12 V CC). 7 Conecte entre sí los cables del mismo color. 50 8 Negro (Toma de tierra del chasis) 9 Azul/blanco La posición de las patillas del conector ISO será diferente según el tipo de vehículo. Conecte 9 y b cuando la patilla 5 sea del tipo control de antena. En otro tipo de vehículo, no se deben conectar nunca 9 y b. a Azul/blanco Conectar al terminal de control del sistema del amplificador de potencia (máx. 300 mA 12 V CC). b Azul/blanco Conectar al terminal de control del relé de la antena automática (máx. 300 mA 12 V CC). c Amarillo/negro Si utiliza un equipo con función de silenciamiento, conecte este cable con el cable de silenciamiento de audio de ese equipo. En caso contrario, mantenga el cable de silenciamiento de audio sin ninguna conexión. d Cables de altavoces Blanco: delantero izquierdo + Blanco/negro: delantero izquierdo * Gris: delantero derecho + Gris/negro: delantero derecho * Verde: trasero izquierdo + o altavoz de subgraves + Verde/negro: trasero izquierdo * o altavoz de subgraves * Violeta: trasero derecho + o altavoz de subgraves + Violeta/negro: trasero derecho * o altavoz de subgraves * e Conector ISO En algunos vehículos, el conector ISO puede estar dividido en dos. En este caso, asegúrese de conectar los dos conectores. Notas ! Cambie el menú inicial de esta unidad. Consulte SP-P/O MODE (ajuste de la salida posterior y del preamplificador) en la página 48. La salida de graves de esta unidad es monoaural. ! Al usar un altavoz de subgraves de 70 W (2 W), conecte el mismo a los cables violeta y violeta/negro de esta unidad. No conecte nada al cable verde ni al verde/negro. ! Se logra un rendimiento óptimo si la unidad se instala en un ángulo inferior a 60°. 60° Amplificador de potencia (se vende por separado) Realice estas conexiones cuando utilice el amplificador opcional. 3 1 5 2     4 ! Cuando instale, para asegurar la dispersión apropiada del calor durante el uso de esta unidad, asegúrese de dejar un amplio espacio por detrás del panel trasero y enrolle los cables sueltos de modo que no bloqueen las aberturas de ventilación. 5 1 Control remoto del sistema Conexión a cable azul/blanco. 2 Amplificador de potencia (se vende por separado) 3 Conectar con cables RCA (se venden por separado) 4 A la salida trasera o salida de subgraves 5 Altavoz trasero o altavoz de subgraves Deje un amplio espacio 5 cm 5 cm Montaje delantero/posterior de DIN Instalación ! ! ! ! Importante Compruebe todas las conexiones y sistemas antes de la instalación final. No utilice piezas no autorizadas, ya que pueden causar fallos de funcionamiento. Consulte a su distribuidor si para la instalación es necesario taladrar orificios o hacer otras modificaciones al vehículo. No instale esta unidad en un lugar donde: — Pueda interferir con el manejo del vehículo. — Pueda lesionar a un pasajero como consecuencia de un frenazo brusco. ! El láser semiconductor se dañará si se sobrecalienta. Instale esta unidad alejada de zonas que alcancen altas temperaturas, como cerca de la salida del calefactor. Esta unidad puede instalarse correctamente tanto si se realiza una instalación frontal o trasera. En la instalación, emplee piezas disponibles en el mercado. Montaje delantero DIN 1 Inserte el manguito de montaje en el salpicadero. Si realiza la instalación en un espacio poco profundo, utilice el manguito de montaje suministrado. Si hay suficiente espacio, utilice el manguito de montaje que venía con el vehículo. Es <QRD3143-C> 50 Black plate (51,1) Sección Instalación Información adicional 2 Fije el manguito de montaje utilizando un destornillador para doblar las pestañas metálicas (90°) y colocarlas en su lugar. Extracción de la unidad 1 2 1 Salpicadero 2 Manguito de montaje # Asegúrese de que la unidad esté firmemente instalada en su lugar. Una instalación inestable puede causar saltos en el audio o un mal funcionamiento de la unidad. 1 Determine la posición correcta, de modo que los orificios del soporte y del lateral de la unidad coincidan. 2 Apriete los dos tornillos en cada lado. 3 1 2 1 Tornillo con rosca cortante (5 mm × 8 mm) 2 Carcasa 3 Salpicadero o consola Mensajes de error Síntoma Causa Resolución Anote el mensaje de error antes de contactar con su concesionario o con el servicio técnico oficial de Pioneer más cercano. La pantalla vuelve automáticamente a la visualización normal. No ha realizado ninguna operación en aproximadamente 30 segundos. Realice la operación de nuevo. El intervalo de repetición de reproducción cambia de manera inesperada. Dependiendo del intervalo de repetición de reproducción, el intervalo seleccionado puede cambiar cuando se selecciona otra carpeta o pista o cuando se utilice el avance rápido/ retroceso. Seleccione de nuevo el intervalo de repetición de reproducción. 1 Anillo de guarnición 2 Pestaña con muesca ! Libere el panel delantero para acceder más fácilmente al anillo de guarnición. ! Al volver a colocar el anillo de guarnición, oriente hacia abajo la pestaña con muesca. 2 Inserte en ambos lados de la unidad las llaves de extracción provistas hasta que se escuche un ligero chasquido. 3 Extraiga la unidad del salpicadero. No se reproNo se pueden duce una sub- reproducir las carpeta. subcarpetas cuando se selecciona FLD (repetición de carpeta). Retirada y colocación del panel delantero Puede extraer el panel delantero para proteger la unidad contra robo. Pulse el botón de soltar, empuje el panel delantero hacia arriba y tire de él hacia sí. Para obtener más información, consulte Extracción del panel delantero para proteger la unidad contra robo y Colocación del panel delantero en la página 44. Seleccione otro intervalo de repetición de reproducción. Está usando un dispositivo, como un teléfono móvil, que transmite ondas eléctricas cerca de la unidad. Mensaje Causa Resolución AMP ERROR La unidad no funciona o la conexión de los altavoces es incorrecta; se activa el circuito de protección. Compruebe la conexión de los altavoces. Si el mensaje no desaparece aun después de apagar y volver a encender el motor, contacte con su distribuidor o con el Servicio técnico oficial Pioneer. Reproductor de CD Mensaje Causa Resolución ERROR-07, El disco está 11, 12, 17, 30 sucio. Limpie el disco. El disco está ra- Sustituya el disco. yado. No hay informa- Cambie la pantaNO XXXX aparece cuan- ción de texto in- lla o reproduzca otra pista/archivo. do se cambia corporada. una pantalla (NO TITLE, por ejemplo). La unidad no funciona correctamente. Hay una interferencia. Comunes Español Montaje trasero DIN Solución de problemas Retire el anillo de guarnición. 1 03 Aleje de la unidad los dispositivos eléctricos que puedan estar causando interferencias. ERROR-07, 10, 11, 12, 15, 17, 30, A0 Se ha producido Coloque la llave un error eléctri- de encendido del co o mecánico. automóvil en la posición de desactivación y luego pase de nuevo a activación, o cambie a una fuente diferente y, a continuación, vuelva a activar el reproductor de CD. Es <QRD3143-C> 51 51 Black plate (52,1) Apéndice Información adicional Mensaje Causa ERROR-15 El disco inserSustituya el disco. tado aparece en blanco. ERROR-23 Formato de CD no compatible. Sustituya el disco. FORMAT READ A veces se produce un retraso entre el comienzo de la reproducción y la emisión del sonido. Espere hasta que el mensaje desaparezca y oiga sonido. El disco insertado no contiene archivos reproducibles. Sustituya el disco. NO AUDIO SKIPPED PROTECT Resolución Información adicional Pautas para el manejo Discos y reproductor Utilice únicamente discos que tengan uno de estos dos logotipos: Quizá no pueda reproducir algunos discos debido a sus características, formato, programas grabados, entorno de reproducción, condiciones de almacenamiento u otras causas. Las vibraciones en las carreteras pueden interrumpir la reproducción de un disco. Utilice discos de 12 cm. No utilice discos de 8 cm o un adaptador de discos de 8 cm. Lea las advertencias de los discos antes de utilizarlos. Utilice solo discos convencionales y completamente circulares. No use discos con formas irregulares. Al usar discos de superficie imprimible para etiquetas, lea primero las instrucciones y las advertencias de los discos. Es posible que algunos discos no puedan insertarse ni expulsarse. La utilización de este tipo de discos puede dañar el equipo. El disco inserSustituya el disco. tado contiene archivos protegidos con DRM. Todos los archi- Sustituya el disco. vos del disco insertado tienen DRM integrado. La condensación puede afectar temporalmente al rendimiento del reproductor. Deje de usarlo durante una hora aproximadamente para que se adapte a la temperatura más cálida. Además, si los discos tienen humedad, séquelos con un paño suave. No coloque ningún otro elemento que no sea un CD en la ranura de carga de CD. No use discos rotos, astillados, deformados o dañados, ya que pueden causar daños al reproductor. No es posible reproducir discos CD-R/RW no finalizados. No toque la superficie grabada de los discos. Cuando no utilice los discos, guárdelos en sus cajas. No fije etiquetas, no escriba ni aplique sustancias químicas en la superficie de los discos. Para limpiar un CD, pásele un paño suave desde el centro hacia afuera. No pegue etiquetas compradas por separado ni otro tipo de material a los discos. ! Los discos podrían combarse y no podrán reproducirse. ! Las etiquetas pueden despegarse durante la reproducción, evitando la expulsión del disco y causando de este modo daños en el equipo. La carga y expulsión frecuente de un disco DualDisc puede producir ralladuras en el disco; las ralladuras graves pueden producir problemas de reproducción en esta unidad. En algunos casos, un DualDisc puede atascarse en la ranura de carga del disco y no se expulsará, para evitarlo, recomendamos que no utilice DualDisc en esta unidad. Consulte la información del fabricante del disco para obtener más información sobre DualDisc. Compatibilidad con audio comprimido WMA Extensión de archivo: .wma Velocidad de grabación: de 48 kbps a 320 kbps (CBR) y de 48 kbps a 384 kbps (VBR) Frecuencia de muestreo: 32 kHz, 44,1 kHz, 48 kHz Windows Media Audio Professional, Lossless, Voice/DRM Stream/Stream con vídeo: no compatible MP3 Extensión de archivo: .mp3 DualDisc Los discos DualDisc (discos dobles) son discos de dos caras que incluyen un CD grabable de audio en una cara y un DVD grabable de vídeo en la otra cara. Debido a que la cara del CD de los discos DualDisc no es físicamente compatible con el estándar general de CD, es posible que no se pueda reproducir la cara del CD en esta unidad. Velocidad de grabación: de 8 kbps a 320 kbps (CBR), VBR Frecuencia de muestreo: de 8 kHz a 48 kHz (32 kHz, 44,1 kHz, 48 kHz para énfasis) Versiones de etiqueta ID3 compatibles: 1.0, 1.1, 2.2, 2.3, 2.4 (la etiqueta ID3 versión 2.x tiene prioridad sobre la versión 1.x) Lista de reproducción M3u: no compatible MP3i (MP3 interactivo), mp3 PRO: no compatible 52 Es <QRD3143-C> 52 Black plate (53,1) Apéndice Información adicional WAV Información adicional Transferencia de datos en formato Packet Write: no compatible Extensión de archivo: .wav Bits de cuantificación: 8 y 16 (LPCM), 4 (MS ADPCM) Frecuencia de muestreo: 16 kHz a 48 kHz (LPCM), 22,05 kHz y 44,1 kHz (MS ADPCM) Información complementaria Solo se pueden visualizar los primeros 32 caracteres como nombre de archivo (incluida la extensión) o nombre de carpeta. PRECAUCIÓN No deje los discos en lugares donde puedan verse sometidos a altas temperaturas. Secuencia de archivos de audio El usuario no puede asignar números de carpeta ni especificar secuencias de reproducción con esta unidad. 01 02 1 2 03 04 5 6 Disco Jerarquía de carpetas reproducibles: hasta ocho niveles (una jerarquía práctica de carpetas tiene menos de dos niveles). Carpetas reproducibles: hasta 99 Archivos reproducibles: hasta 999 Sistema de archivos: ISO 9660 Nivel 1 y 2, Romeo, Joliet Reproducción multisesión: compatible 3 4 05 Nivel 1 Nivel 2 Nivel 3 Nivel 4 D: C D: C D: C D: C :А :Б :В :Г :Д : Е, Ё :Ж :З : И, Й :К :Л :М :Н :О :П :Р :С :Т :У :Ф :Х :Ц :Ч : Ш, Щ :Ъ :Ы :Ь :Э :Ю :Я Windows Media es una marca registrada o una marca de fábrica de Microsoft Corporation en los Estados Unidos y/u otros países. Este producto incluye tecnología propiedad de Microsoft Corporation, y no se puede usar ni distribuir sin una licencia de Microsoft Licensing, Inc. D: Visualización C: Carácter Copyright y marcas registradas iTunes Apple e iTunes son marcas comerciales de Apple Inc., registradas en los EE.UU. y en otros países. Ejemplo de una jerarquía Esta unidad puede no funcionar correctamente, según la aplicación utilizada para codificar archivos WMA. D: C WMA Español Los textos en ruso que se visualizarán en esta unidad se deben codificar con los siguientes conjuntos de caracteres: ! Unicode (UTF-8, UTF-16) ! Los conjuntos de caracteres distintos de Unicode que se usan en el entorno Windows y que están ajustados en ruso en la configuración de idiomas múltiples. Independientemente de la longitud de la secciones en blanco que haya entre las canciones de la grabación original, los discos de audio comprimidos se reproducirán con una breve pausa entre cada canción. Tabla de caracteres rusos : carpeta : archivo de audio comprimido 01 a 05: número de carpeta 1 a 6: secuencia de reproducción Disco La secuencia de selección de carpetas u otras operaciones pueden diferir, dependiendo del software de codificación o escritura. MP3 La venta de este producto solo otorga una licencia para su uso privado, no comercial. No otorga ninguna licencia ni concede ningún derecho a utilizar este producto en transmisiones comerciales (es decir, lucrativas) en tiempo real (terrestres, vía satélite, por cable y/o por cualquier otro medio), transmisiones/streaming por Internet, intranets u otras redes o en otros sistemas de distribución de contenido electrónico, como por ejemplo, aplicaciones de pago por escucha (pay-audio) o audio bajo demanda (audio-on-demand). Se necesita una licencia independiente para su uso comercial. Para obtener más información, visite http://www.mp3licensing.com. Es <QRD3143-C> 53 53 Black plate (54,1) Apéndice Información adicional Especificaciones Generales Fuente de alimentación .... 14,4 V cc (10,8 V a 15,1 V permisible) Sistema de derivación a tierra ................................... Tipo negativo Consumo máximo de corriente ................................... 10,0 A Dimensiones (An × Al × Pr): DIN Bastidor ............. 178 mm × 50 mm × 165 mm Cara anterior ...... 188 mm × 58 mm × 16 mm D Bastidor ............. 178 mm × 50 mm × 165 mm Cara anterior ...... 170 mm × 46 mm × 16 mm Peso ................................ 1 kg Reproductor de CD Sistema ........................... Sistema de audio de discos compactos Discos utilizables ............. Disco compacto Relación de señal a ruido ................................... 94 dB (1 kHz) (red IEC-A) Número de canales .......... 2 (estéreo) Formato de decodificación MP3 ................................... MPEG-1 & 2 Audio Layer 3 Formato de decodificación WMA ................................... Ver. 7, 7.1, 8, 9, 10, 11, 12 (audio 2 canales) (Windows Media Player) Formato de señal WAV ..... PCM lineal & MS ADPCM (No comprimido) Sintonizador de FM Intervalo de frecuencias ... de 87,5 MHz a 108,0 MHz Sensibilidad utilizable ...... 9 dBf (0,8 µV/75 W, mono, señal/ruido: 30 dB) Relación de señal a ruido ................................... 72 dB (red IEC-A) Audio Potencia de salida máxima ................................... 50 W × 4 70 W × 1/2 W (para altavoz de subgraves) Potencia de salida continua ................................... 22 W × 4 (50 Hz a 15 000 Hz, 5% THD, 4 W de carga, ambos canales activados) Impedancia de carga ....... 4 W (4 W a 8 W permisibles) Nivel de salida máxima del preamplificador ................................... 2,0 V Contorno de sonoridad ..... +10 dB (100 Hz), +6,5 dB (10 kHz) (volumen: –30 dB) Ecualizador (ecualizador gráfico de 5 bandas): Frecuencia ................ 80 Hz/250 Hz/800 Hz/ 2,5 kHz/8 kHz Gama de ecualización ............................ ±12 dB (paso de 2 dB ) Altavoz de subgraves (mono): Frecuencia ................ 50 Hz/63 Hz/80 Hz/100 Hz/ 125 Hz/160 Hz/200 Hz Pendiente ................. –6 dB/oct, –12 dB/oct Ganancia .................. +6 dB a –24 dB Fase .......................... Normal/Inversa 54 Sintonizador de MW Intervalo de frecuencias ... de 531 kHz a 1 602 kHz Sensibilidad utilizable ...... 25 µV (señal/ruido: 20 dB) Relación de señal a ruido ................................... 62 dB (red IEC-A) Sintonizador de LW Intervalo de frecuencias ... de 153 kHz a 281 kHz Sensibilidad utilizable ...... 28 µV (señal/ruido: 20 dB) Relación de señal a ruido ................................... 62 dB (red IEC-A) Nota Las especificaciones y el diseño están sujetos a modificaciones sin previo aviso. Es <QRD3143-C> 54 Black plate (55,1) Español Es <QRD3143-C> 55 55 Black plate (56,1) Abschnitt Bevor Sie beginnen 01 Vielen Dank, dass Sie sich für dieses PIONEER-Produkt entschieden haben. Bitte lesen Sie diese Anleitung vor der Verwendung dieses Produkts zur Gewährleistung seiner ordnungsgemäßen Verwendung durch. Lesen und befolgen Sie dabei insbesondere die Hinweise WARNUNG und VORSICHT. Bewahren Sie die Anleitung zur zukünftigen Bezugnahme sicher und griffbereit auf. Bevor Sie beginnen Zu diesem Gerät Die Tuner-Frequenzen dieses Geräts sind für Westeuropa, Asien, den Mittleren Osten, Afrika und Ozeanien bestimmt. Der Gebrauch in anderen Gebieten kann zu mangelhaftem Empfang führen. Die RDS-Funktion (Radio-Datensystem) ist nur in Gebieten mit UKW-Sendern verfügbar, die RDS-Signale ausstrahlen. Wichtig Bitte tragen Sie die folgenden Informationen in das dafür vorgesehene Formular auf der Rückseite der Anleitung ein: Mischen Sie dieses Produkt, wenn Sie es entsorgen wollen, nicht mit gewöhnlichen Haushaltsabfällen. Es gibt ein getrenntes Sammelsystem für gebrauchte elektronische Produkte, über das die richtige Behandlung, Rückgewinnung und Wiederverwertung gemäß der bestehenden Gesetzgebung gewährleistet wird. Privathaushalte in den Mitgliedstaaten der EU, in der Schweiz und in Norwegen können ihre gebrauchten elektronischen Produkte kostenfrei bei speziell dafür eingerichteten Sammelstellen abgeben oder zu einem Fachhändler zurückbringen (sofern sie ein vergleichbares neues Produkt kaufen). In den Ländern, die hier nicht aufgeführt sind, wenden Sie sich hinsichtlich der zu beachtenden Entsorgungsweise bitte an die zuständige Gemeindeverwaltung. Auf diese Weise stellen Sie sicher, dass das zu entsorgende Produkt der erforderlichen Verarbeitung, Rückgewinnung und Wiederverwertung zugeführt wird, und verhindern damit potenziell negative Auswirkungen auf die Umwelt sowie Gesundheitsschäden. 56 — 14-stellige Seriennummer (an der Unterseite des Geräts angegeben) — Kaufdatum (Datum der Quittung) — Stempel des Händlers Diese Informationen dienen als Eigentumsnachweis. Im Fall eines Diebstahls teilen Sie der Polizei die 14-stellige Seriennummer und das Kaufdatum des Geräts mit. Bewahren Sie die Bedienungsanleitung an einem sicheren Ort auf. VORSICHT Bei diesem Gerät handelt es sich zwar um ein Laserprodukt der Klasse 1, das entsprechend dem Standard Sicherheit für Laserprodukte IEC 60825-1:2007 klassifiziert ist. VORSICHT ! Dieses Gerät darf nicht mit Flüssigkeiten in Kontakt kommen. Dies könnte einen Stromschlag verursachen. Darüber hinaus kann der Kontakt mit Flüssigkeit eine Beschädigung des Geräts, Rauchentwicklung und Überhitzung nach sich ziehen. ! Wählen Sie stets eine Lautstärke, bei der Sie Umgebungsgeräusche noch deutlich wahrnehmen können. ! Setzen Sie dieses Gerät keiner Feuchtigkeit aus. ! Beim Abtrennen oder Entladen der Batterie werden sämtliche vorprogrammierten Speicher gelöscht. Hinweis Funktionseinstellungen werden selbst dann abgeschlossen, wenn das Menü vor dem Bestätigen geschlossen wird. Im Störungsfall Sollte dieses Gerät nicht ordnungsgemäß funktionieren, dann wenden Sie sich an Ihren Händler oder an die nächstgelegene PIONEERKundendienststelle. LASER KLASSE 1 De <QRD3143-C> 56 Black plate (57,1) Abschnitt Bedienung des Geräts Bedienung des Geräts Hauptgerät Anzeige 1 2 34 5 6 7 8 9 a b Bezeichnung 1 c d SRC/OFF 9 (Zurück)/DIMMER (Dimmer) 3 MULTI-CONTROL (M.C.) a c/d b 1/ c AUX-Eingang (3,5-mm-Stereoanschluss) 4 (Liste) 5 DISP Disc-Ladeschacht 7 2 Unterinformationsbereich Zum Anzeigen von Unterinformationen. 3 TA (Verkehrsdurchsagen) Die Verkehrsdurchsage ist aktiviert. 4 TP (VerkehrsprogrammIdentifizierung) Es ist ein Sender, der Verkehrsfunk anbietet, abgestimmt. Taste zum Entriegeln der Frontplatte d (Equalizer) (Sound Retriever) 6 LOC Die Lokal-Suchlaufabstimmung ist aktiviert. 7 (Wiederholwiedergabe) Die Titel- oder Ordner-Wiederholwiedergabe ist eingeschaltet. 8 (zufällige Wiedergabe) Die zufallsgesteuerte Wiedergabe ist eingeschaltet. Hauptinformationsbereich ! Tuner: Frequenzband und Frequenz ! RDS: Programm-ServiceName, PTY-Information und andere Textinformationen ! CD-Player: verstrichene Wiedergabezeit und Textinformationen Display-Anzeige 1 2 3 9 4 5 6 8 7 Die „Sound Retriever“-Funktion ist aktiviert. 5 bis 6/ 9 a a Erscheint, wenn eine untergeordnete Ordner- oder Menüebene vorhanden ist. Setup-Menü Wenn Sie nach der Installation den Zündschalter in die Position EIN drehen, wird das SetupMenü auf dem Display angezeigt. In diesem Menü können Sie folgende Optionen einstellen. 1 Drehen Sie nach der Installation des Geräts den Zündschalter auf EIN. Die Angabe SET UP erscheint. 2 Drehen Sie M.C., um zu YES umzuschalten. # Bedienen Sie das Gerät nicht innerhalb von 30 Sekunden, wird das Setup-Menü nicht angezeigt. # Wenn Sie diese Einstellung jetzt nicht vornehmen möchten, drehen Sie M.C., auf NO. Drücken Sie den Regler, um die Auswahl zu bestätigen. Wenn Sie NO wählen, können Sie keine Einstellungen im Setup-Menü vornehmen. 3 Drücken Sie zur Auswahl M.C. 4 Gehen Sie zur Einstellung des Menüs folgendermaßen vor. Sie müssen Ihre Auswahl bestätigen, um die nächste Menüoption aufrufen zu können. LANGUAGE (Spracheinstellung) Das Gerät kann Textinformationen komprimierter Audiodateien auch dann anzeigen, wenn sie entweder in einem lateinischen oder kyrillischen Alphabet aufgezeichnet wurden. ! Falls die für die Aufzeichnung verwendete Sprache und die gewählte Spracheinstellung nicht übereinstimmen, werden die Textinformationen ggf. nicht richtig angezeigt. ! Bestimmte Zeichen werden ggf. nicht ordnungsgemäß angezeigt. 1 Drehen Sie M.C., um die gewünschte Einstellung zu wählen. ENG (Englisch)—РУС (Russisch) 2 Drücken Sie M.C., um die Auswahl zu bestätigen. CLOCK SET (Einstellen der Uhrzeit) 1 Drehen Sie M.C., um die Stunde einzustellen. 2 Drücken Sie auf M.C., um die Minuten auszuwählen. 3 Drehen Sie M.C., um die Minuten einzustellen. 4 Drücken Sie M.C., um die Auswahl zu bestätigen. FM STEP (UKW-Kanalraster) Bei der Suchlaufabstimmung wird normalerweise das 50-kHz-UKW-Kanalraster verwendet. Wenn der Alternativfrequenzsuchlauf (AF) oder die Verkehrsmeldungen (TA) eingeschaltet sind, ändert sich das Kanalraster automatisch zu 100 kHz. Es kann jedoch vorteilhaft sein, das Kanalraster für den Alternativfrequenzsuchlauf auf 50 kHz einzustellen. ! Bei der manuellen Abstimmung bleibt das Kanalraster auf 50 kHz eingestellt. 1 Drehen Sie M.C., um die UKW-KanalrasterFunktion zu wählen. 50 (50 kHz)—100 (100 kHz) 2 Drücken Sie M.C., um die Auswahl zu bestätigen. Die Angabe QUIT erscheint. De <QRD3143-C> 57 Deutsch 6 (Liste) BAND 2 Die Listenfunktion wird bedient. 1 Bezeichnung 8 h (Auswurf) Status 02 57 Black plate (58,1) Abschnitt Bedienung des Geräts 02 5 Um die Einstellungen abzuschließen, drehen Sie M.C., um zu YES zu wechseln. # Wenn Sie die Einstellung erneut vornehmen möchten, drehen Sie M.C., um zu NO zu wechseln. Drücken Sie den Regler, um die Auswahl zu bestätigen. 6 Bedienung des Geräts Entfernen der Frontplatte zum Schutz vor Diebstahl 1 Drücken Sie die Taste zum Entriegeln der Frontplatte. 2 Drücken Sie die Frontplatte nach oben (M) und ziehen Sie sie in Ihre Richtung (N). Drücken Sie zur Auswahl M.C. Hinweise ! Sie können die Menüoptionen über das Systemmenü einstellen. Für Details zu den Einstellungen siehe Systemmenü auf Seite 62. ! Das Einstellmenü kann durch Drücken von SRC/OFF abgebrochen werden. Grundlegende Bedienvorgänge Wichtig ! Gehen Sie beim Abnehmen bzw. Anbringen der Frontplatte sorgfältig vor. ! Setzen Sie die Frontplatte keinen übermäßigen Stößen aus. ! Setzen Sie die Frontplatte weder direkter Sonnenbestrahlung noch hohen Temperaturen aus. ! Entfernen Sie alle etwaigen angeschlossenen Kabel und Geräte, bevor Sie die Frontplatte abnehmen, um eine Beschädigung des Geräts oder des Fahrzeuginneren zu vermeiden. Wählen einer Programmquelle 1 Drücken Sie SRC/OFF, um zwischen den folgenden Optionen umzuschalten: TUNER (Tuner)—CD (CD-Player)—AUX (AUX) Regeln der Lautstärke 1 Drehen Sie M.C., um die Lautstärke anzupassen. VORSICHT 3 Bewahren Sie die abgenommene Frontplatte stets in einer Schutzhülle, wie zum Beispiel einem Etui, auf. Wiederanbringen der Frontplatte 1 Schieben Sie die Frontplatte nach links. Achten Sie darauf, die Zapfen links am Hauptgerät in die Aussparungen an der Frontplatte einzuführen. Parken Sie Ihr Fahrzeug aus Sicherheitsgründen zum Abnehmen der Frontplatte. Hinweis Wenn das blau/weiße Kabel dieses Geräts an die Steuerklemme des Automatikantennenrelais des Kraftfahrzeugs angeschlossen wird, wird die Antenne ausgefahren, sobald das Gerät eingeschaltet wird. Zum Einfahren der Antenne schalten Sie die Programmquelle aus. Häufig verwendete Menüschritte 2 Drücken Sie dann gegen die rechte Seite der Frontplatte, bis sie sicher einrastet. Sollten Sie die Frontplatte nicht erfolgreich am Hauptgerät anbringen können, stellen Sie sicher, dass sie korrekt vor dem Gerät positioniert ist. Wenden Sie keine Gewalt beim Anbringen der Frontplatte an, da diese oder das Hauptgerät sonst beschädigt werden könnten. Einschalten des Geräts 1 Drücken Sie die Taste SRC/OFF, um das Gerät einzuschalten. Zurückschalten zur vorherigen Anzeige Zum Zurückschalten zur vorherigen Liste (bzw. zum übergeordneten Ordner) 1 Drücken Sie /DIMMER. Zurückschalten zur normalen Anzeige Beenden des Hauptmenüs 1 Drücken Sie BAND. Zurückschalten zur normalen Anzeige von der Liste 1 Drücken Sie BAND. Tuner Grundlegende Bedienvorgänge Wahl eines Bands (Wellenbereich) 1 Drücken Sie BAND, bis der gewünschte Wellenbereich angezeigt wird (FM1, FM2, FM3 für UKW bzw. MW/LW). Wechseln der voreingestellten Sender 1 Drücken Sie c oder d. ! Wählen Sie PCH (voreingesteller Kanal) unter SEEK, um diese Funktion verwenden zu können. Für Details zu den Einstellungen siehe SEEK (Einstellen der linken/rechten Tasten) auf Seite 59. Manuelle (schrittweise) Abstimmung 1 Drücken Sie c oder d. ! Wählen Sie MAN (manuelle Abstimmung) unter SEEK, um diese Funktion verwenden zu können. Für Details zu den Einstellungen siehe SEEK (Einstellen der linken/rechten Tasten) auf Seite 59. Suchlauf 1 Drücken und halten Sie c oder d gedrückt und lassen Sie die Taste dann wieder los. Durch kurzes Drücken von c oder d kann die Suchlaufabstimmung aufgehoben werden. Durch Drücken und Gedrückthalten von c oder d können Sender übersprungen werden. Die Suchlaufabstimmung beginnt, sobald c bzw. d losgelassen wird. Hinweis Der Alternativfrequenz-Suchlauf (AF) dieses Geräts kann ein- und ausgeschaltet werden. Für den normalen Abstimmbetrieb sollte AF ausgeschaltet sein (siehe AF (Alternativfrequenz-Suchlauf) auf Seite 59). Ausschalten des Geräts 1 Drücken und halten Sie SRC/OFF gedrückt, bis sich das Gerät ausschaltet. 58 De <QRD3143-C> 58 Black plate (59,1) Abschnitt Bedienung des Geräts Speichern und Abrufen von Radiostationen für jedes Band Verwendung der Stationstasten 1 Zum Speichern eines abgestimmten Senders drücken Sie eine der Stationstasten (1/ bis 6/ ) und halten diese gedrückt, bis die Stationsnummer nicht mehr blinkt. 2 Drücken Sie eine der Stationstasten (1/ bis 6/ ) zur Auswahl der gewünschten Station. Umschalten der Anzeige Wählen der gewünschten Textinformationen 1 Drücken Sie auf DISP, um zwischen den folgenden Optionen umzuschalten: ! FREQUENCY (Programm-Service-Name oder Frequenz) ! BRDCST INFO (Programm-Service-Name/ PTY-Information) ! CLOCK (Programmquellname und Uhr) Gebrauch der ProgrammtypFunktionen (PTY) Sie können einen Sender anhand eines Programmtyps (PTY) abstimmen. Suchen nach RDS-Stationen anhand eines Programmtyps Sie können nach Programmen eines allgemeinen Typs suchen, wie die, die nachfolgend aufgelistet sind. Siehe Seite 59. (Liste). 1 Drücken Sie auf 2 Drehen Sie M.C., um einen Programmtyp zu wählen. NEWS/INFO—POPULAR—CLASSICS— OTHERS 3 Drücken Sie M.C., um die Suche zu starten. Das Gerät sucht nach einer Station, die ein Programm des gewählten Typs ausstrahlt. Wenn eine solche Station gefunden wird, wird deren Stationsname angezeigt. ! Zum Aufheben des Suchlaufs drücken Sie M.C. erneut. ! Das Programm mancher Sender kann von dem tatsächlich übertragenen Programmtyp (PTY) abweichen. ! Wird kein Sender gefunden, der ein Programm des gewählten Typs ausstrahlt, dann erscheint zwei Sekunden lang NOT FOUND und der Tuner schaltet auf die ursprüngliche Station zurück. PTY-Liste L. CLASS (Leichte klassische Musik), CLASSIC (Klassische Musik) OTHERS (Sonstiges) EDUCATE (Bildung), DRAMA (Drama), CULTURE (Kultur), SCIENCE (Wissenschaft), VARIED (Gemischtes), CHILDREN (Kinderprogramme), SOCIAL (Soziales), RELIGION (Religion), PHONE IN (Telefongesprächsprogramme), TOURING (Reisen), LEISURE (Freizeit), DOCUMENT (Dokumentarsendungen) Funktionseinstellungen 1 Drücken Sie auf M.C., um das Hauptmenü anzuzeigen. 2 Drehen Sie M.C., um die Menüoption zu wechseln, und drücken Sie auf FUNCTION, um die angezeigte Option zu wählen. 3 Drehen Sie M.C., um die gewünschte Funktion zu wählen. Nach der Auswahl können die folgenden Funktionen angepasst werden. # Wenn das MW/LW-Band gewählt ist, stehen nur BSM, LOCAL und SEEK zur Verfügung. BSM (Best-Sender-Memory) NEWS/INFO (Nachrichten und Informationen) NEWS (Nachrichten), AFFAIRS (Tagesereignisse), INFO (Information), SPORT (Sport), WEATHER (Wetter), FINANCE (Finanzen) POPULAR (Pop) POP MUS (Popmusik), ROCK MUS (Rockmusik), EASY MUS (Leichte Hörmusik), OTH MUS (Andere Musik), JAZZ (Jazz), COUNTRY (Countrymusik), NAT MUS (Landesmusik), OLDIES (Oldies), FOLK MUS (Volksmusik) CLASSICS (Klassik) BSM (Best-Sender-Memory) speichert die sechs stärksten Sender automatisch in der Reihenfolge ihrer Signalstärke. 1 Drücken Sie M.C., um BSM einzuschalten. Zum Abbrechen des Speichervorgangs drücken Sie M.C. erneut. 02 LOCAL (Lokal-Suchlaufabstimmung) Mit der Lokal-Suchlaufabstimmung wird nur nach Stationen mit ausreichender Signalstärke für einen guten Empfang gesucht. 1 Drücken Sie auf M.C., um die gewünschte Einstellung zu wählen. UKW: OFF—LV1—LV2—LV3—LV4 MW/LW: OFF—LV1—LV2 Bei Auswahl der höchsten Stufe werden nur die stärksten Sender empfangen, während bei Auswahl der niedrigeren Stufen schwächere Sender zugelassen werden. TA (Verkehrsdurchsagebereitschaft) 1 Drücken Sie M.C., um die Verkehrsdurchsagebereitschaft ein- oder auszuschalten. AF (Alternativfrequenz-Suchlauf) 1 Drücken Sie M.C., um den AlternativfrequenzSuchlauf ein- oder auszuschalten. NEWS (Nachrichtenunterbrechung) 1 Drücken Sie M.C., um die Nachrichtenfunktion ein- oder auszuschalten. SEEK (Einstellen der linken/rechten Tasten) Sie können den linken und rechten Tasten des Gerät eine Funktion zuweisen. Wählen Sie MAN (manuelle Abstimmung) zur manuellen Abstimmung oder PCH (vorprogrammierter Kanal) zum Umschalten zwischen den vorprogrammierten Kanälen. 1 Drücken Sie M.C., um MAN oder PCH zu wählen. Deutsch Hinweise ! Wenn der Programm-Service-Name nicht unter FREQUENCY abgerufen werden kann, wird stattdessen die Sendefrequenz angezeigt. Der Programm-Service-Name wird bei einer Erkennung angezeigt. ! Die Textinformation BRDCST INFO ändert sich automatisch. ! Je nach dem Band kann die Textinformation geändert werden. ! Welche Textinformationen geändert werden können, hängt vom Bereich ab. Bedienung des Geräts REGION (Regional) Bei Verwendung des Alternativfrequenz-Suchlaufs beschränkt die Regionalfunktion die Auswahl auf Sender, die regionale Programme ausstrahlen. 1 Drücken Sie M.C., um die Regionalfunktion ein- oder auszuschalten. De <QRD3143-C> 59 59 Black plate (60,1) Abschnitt Bedienung des Geräts 02 CD/CD-R/CD-RW-Discs Grundlegende Bedienvorgänge Wiedergabe einer CD/CD-R/CD-RW-Disc 1 Legen Sie die Disc mit der Etikettenseite nach oben in den Ladeschacht. Auswerfen einer CD/CD-R/CD-RW-Disc 1 Drücken Sie auf h. Wählen eines Ordners 1 Drücken Sie 1/ oder 2/ . Wahl eines Titels 1 Drücken Sie c oder d. Schnellvorlauf bzw. -rücklauf 1 Drücken und halten Sie c oder d gedrückt. ! Bei der Wiedergabe von Dateien im komprimierten Audio-Format wird beim schnellen Vor- und Rücklauf kein Ton ausgegeben. Rückkehr zum Stammordner 1 Halten Sie BAND gedrückt. Umschalten zwischen dem komprimierten Audioformat und CD-DA 1 Drücken Sie BAND. Bedienung des Geräts Umschalten der Anzeige Wählen der gewünschten Textinformationen 1 Drücken Sie auf DISP, um zwischen den folgenden Optionen umzuschalten: CD-DA ! ELAPSED TIME (Titelnummer und Wiedergabezeit) ! CLOCK (Programmquellname und Uhr) ! SPEANA (Spektralanalysator) CD-TEXT ! TRACK INFO (Titelname/Titel-Künstler/ Disc-Titel) ! ELAPSED TIME (Titelnummer und Wiedergabezeit) ! CLOCK (Programmquellname und Uhr) ! SPEANA (Spektralanalysator) MP3/WMA/WAV ! TRACK INFO (Titelname/Künstlername/Albumtitel) ! FILE INFO (Dateiname/Ordnername) ! ELAPSED TIME (Titelnummer und Wiedergabezeit) ! CLOCK (Programmquellname und Uhr) ! SPEANA (Spektralanalysator) Hinweise ! Die Textinformation TRACK INFO und FILE INFO ändert sich automatisch. ! Abhängig vom Mediadateityp bzw. der für das Schreiben der MP3-Dateien auf eine Disc verwendeten Version von iTunes werden die mit den Audiodateien gespeicherten Textinformationen ggf. nicht richtig angezeigt. ! Welche Textinformationen geändert werden können, hängt vom Medium ab. Auswählen und Wiedergeben von Dateien/Titeln der Namensliste 1 Drücken Sie , um in den Datei-/Titellistenmodus umzuschalten. 60 2 Verwenden Sie M.C., um den Namen der gewünschten Datei (bzw. des gewünschten Ordners) zu wählen. Auswählen einer Datei oder eines Ordners 1 Drehen Sie M.C. Wiedergabe 1 Drücken Sie nach Auswahl einer Datei oder eines Titels auf M.C. Anzeige einer Liste der Dateien (oder Ordner) im gewählten Ordner 1 Drücken Sie nach Auswahl eines Ordners auf M.C. Wiedergabe eines Musiktitels im gewählten Ordner 1 Drücken und halten Sie M.C. nach Auswahl des Ordners gedrückt. Bedienvorgänge mit speziellen Tasten Wählen eines Wiederholbereichs 1 Drücken Sie 6/ , um zwischen den folgenden Optionen umzuschalten: ! ALL – Wiederholung aller Titel ! ONE – Wiederholung des momentanen Titels ! FLD – Wiederholung des momentanen Ordners Abspielen von Titeln in zufälliger Reihenfolge , um die zufallsgesteuerte 1 Drücken Sie 5/ Wiedergabe ein- oder auszuschalten. Die Titel innerhalb des gewählten Wiederholbereichs werden in einer zufälligen Reihenfolge gespielt. ! Um Titel während der zufälligen Wiedergabe zu ändern, drücken Sie auf d, um zum nächsten Titel zu wechseln. Durch Drücken von c wird die Wiedergabe des aktuellen Titels von seinem Anfang neu gestartet. Pausieren der Wiedergabe 1 Drücken Sie 4/PAUSE, um die Wiedergabe anzuhalten oder fortzusetzen. Verbessern der komprimierten Audiodaten und Wiederherstellen eines reichen Klangbild (Sound Retriever) 1 Drücken Sie 3/S.Rtrv, um zwischen den folgenden Optionen umzuschalten: 1—2—OFF (Aus) 1 wirkt bei einem niedrigen und 2 bei einem hohen Kompressionsfaktor. Funktionseinstellungen 1 Drücken Sie auf M.C., um das Hauptmenü anzuzeigen. 2 Drehen Sie M.C., um die Menüoption zu wechseln, und drücken Sie auf FUNCTION, um die angezeigte Option zu wählen. Nach der Auswahl kann die unten stehende Funktion angepasst werden. S.RTRV (Sound Retriever) Verbessert komprimierte Audiodaten und stellt ein reiches Klangbild wieder her. 1 Drücken Sie auf M.C., um die gewünschte Einstellung zu wählen. Für detaillierte Informationen hierzu siehe Verbessern der komprimierten Audiodaten und Wiederherstellen eines reichen Klangbild (Sound Retriever) auf Seite 60. Audio-Einstellungen 1 Drücken Sie auf M.C., um das Hauptmenü anzuzeigen. 2 Drehen Sie M.C., um die Menüoption zu wechseln, und drücken Sie auf AUDIO, um die angezeigte Option zu wählen. De <QRD3143-C> 60 Black plate (61,1) Abschnitt Bedienung des Geräts 3 Drehen Sie M.C., um die gewünschte Audio-Funktion zu wählen. Nach der Auswahl können die folgenden Audiofunktionen angepasst werden. ! FADER steht nicht zur Verfügung, wenn in SP-P/O MODE die Option SUB.W/SUB.W gewählt wurde. Für detaillierte Informationen hierzu siehe SP-P/O MODE (Heckausgangund Preout-Einstellungen) auf Seite 63. ! SUB.W, SUB.W CTRL und HPF SETTING stehen nicht zur Verfügung, wenn in SP-P/O MODE die Option REAR/REAR gewählt wurde. Für detaillierte Informationen hierzu siehe SP-P/O MODE (Heckausgangund Preout-Einstellungen) auf Seite 63. ! SUB.W CTRL und HPF SETTING stehen nicht zur Verfügung, wenn in OFF die Option SUB.W gewählt wurde. Für detaillierte Informationen hierzu siehe SUB.W (Subwoofer Ein/Aus) auf Seite 61. FADER (Überblendeinstellung) BALANCE (Balance-Einstellung) 1 Drücken Sie auf M.C., um den Einstellmodus aufzurufen. 2 Drehen Sie M.C., um die Links-/Rechts-Lautsprecherbalance einzustellen. EQ SETTING (Equalizer-Abruf) 1 Drücken Sie auf M.C., um den Einstellmodus aufzurufen. 2 Drehen Sie M.C., um einen Equalizer zu wählen. POWERFUL—NATURAL—VOCAL—CUSTOM1—CUSTOM2—FLAT—SUPER BASS Das Equalizer-Band und der Equalizer-Pegel können individuell angepasst werden, wenn CUSTOM1 oder CUSTOM2 gewählt ist. Schließen Sie bei Wahl von CUSTOM1 oder CUSTOM2 den unten genannten Vorgang ab. Kehren Sie bei Wahl einer anderen Option durch Drücken auf M.C. zur vorherigen Anzeige zurück. ! CUSTOM1 kann für jede Quelle separat eingestellt werden. ! Bei CUSTOM2 handelt es sich um eine gemeinsam verwendete Einstellung für alle Quellen. 3 Drücken Sie auf M.C., um den Einstellmodus aufzurufen. 4 Drücken Sie M.C., um zwischen den folgenden Optionen umzuschalten: Equalizerband—Equalizer-Pegel 5 Drehen Sie M.C., um die gewünschte Einstellung zu wählen. Equalizer-Band: 80HZ—250HZ—800HZ— 2.5KHZ—8KHZ Equalizer-Pegel: +6 bis –6 ! Sie können den Equalizer auch durch wiederwechseln. holtes Drücken auf LOUDNESS (Loudness) Die Loudness-Funktion kompensiert die verminderte Wahrnehmung von niedrigen und hohen Frequenzen bei geringer Lautstärke. 1 Drücken Sie auf M.C., um die gewünschte Einstellung zu wählen. OFF (Aus)—LOW (Niedrig)—MID (Mittel)—HI (Hoch) Dieses Gerät ist mit einem Subwoofer-Ausgang ausgestattet, der ein- und ausgeschaltet werden kann. 1 Drücken Sie auf M.C., um die gewünschte Einstellung zu wählen. NOR (Normalphase)—REV (Gegenphase)— OFF (Subwoofer Aus) SUB.W CTRL (Subwoofer-Einstellungen) Vom Subwoofer werden nur solche Frequenzen ausgegeben, die unter dem gewählten Bereich liegen. 1 Drücken Sie auf M.C., um den Einstellmodus aufzurufen. 2 Drücken Sie M.C., um zwischen den folgenden Optionen umzuschalten: Trennfrequenz—Ausgabepegel—Pegel der Steilheit Einstellbare Werte blinken. 3 Drehen Sie M.C., um die gewünschte Einstellung zu wählen. Trennfrequenz: 50HZ—63HZ—80HZ—100HZ —125HZ—160HZ—200HZ Ausgangspegel: –24 bis +6 Pegel der Steilheit: –6— –12 BASS BOOST (Bassverstärkung) 1 Drücken Sie auf M.C., um den Einstellmodus aufzurufen. 2 Drehen Sie M.C., um den gewünschten Pegel zu wählen. Während der Erhöhung bzw. Verminderung des Pegels wird 0 bis +6 angezeigt. HPF SETTING (Hochpassfilter-Anpassung) 02 Wenn die im Ausgabe-Frequenzbereich des Subwoofers enthaltenen Basstöne nicht über den Front- oder Hecklautsprecher ausgegeben werden sollen, schalten Sie den Hochpassfilter (HPF) ein. Über den Front- oder Heckausgang werden dann nur Frequenzen ausgegeben, die über dem gewählten Bereich liegen. 1 Drücken Sie auf M.C., um den Einstellmodus aufzurufen. 2 Drücken Sie M.C., um zwischen den folgenden Optionen umzuschalten: Trennfrequenz—Pegel der Steilheit 3 Drehen Sie M.C., um die gewünschte Einstellung zu wählen. Trennfrequenz: OFF—50HZ—63HZ—80HZ— 100HZ—125HZ—160HZ—200HZ Pegel der Steilheit: –6— –12 SLA (Programmquellen-Pegeleinstellung) Mit der Programmquellen-Pegeleinstellung (SLA) kann der Lautstärkepegel jeder Programmquelle eingestellt werden, um plötzliche Lautstärkeänderungen beim Umschalten von Programmquellen zu vermeiden. ! Die Einstellungen basieren auf der UKW-Lautstärke, die unverändert bleibt. ! Der MW/LW-Lautstärkepegel kann ebenfalls mit dieser Funktion eingestellt werden. ! Bei der Wahl von UKW als Programmquelle kann nicht auf SLA geschaltet werden. 1 Drücken Sie auf M.C., um den Einstellmodus aufzurufen. 2 Drehen Sie M.C., um die Lautstärke für die Programmquelle einzustellen. Einstellbereich: +4 bis –4 Deutsch 1 Drücken Sie auf M.C., um den Einstellmodus aufzurufen. 2 Drehen Sie M.C., um die Front-/Heck-Lautsprecherbalance einzustellen. Bedienung des Geräts SUB.W (Subwoofer Ein/Aus) De <QRD3143-C> 61 61 Black plate (62,1) Abschnitt Bedienung des Geräts 02 Systemmenü Wichtig Die Funktion PW SAVE (Energiesparmodus) wird deaktiviert, wenn die Fahrzeugbatterie abgeklemmt wird und muss neu aktiviert werden, sobald die Batterie wieder angeschlossen wird. Wenn PW SAVE (Energiesparmodus) deaktiviert ist, kann das Gerät je nach Anschlussart Batterieleistung in Anspruch nehmen, sollte die Zündung des Fahrzeugs über keine ACC-Position (Zubehörposition) verfügen. 1 Drücken Sie auf M.C., um das Hauptmenü anzuzeigen. 2 Drehen Sie M.C., um die Menüoption zu wechseln, und drücken Sie auf SYSTEM, um die angezeigte Option zu wählen. 3 Drehen Sie M.C., um die SystemmenüFunktion zu wählen. Nach der Auswahl können die folgenden Systemmenüfunktionen angepasst werden. LANGUAGE (Spracheinstellung) Das Gerät kann Textinformationen komprimierter Audiodateien auch dann anzeigen, wenn sie entweder in einem lateinischen oder kyrillischen Alphabet aufgezeichnet wurden. ! Falls die für die Aufzeichnung verwendete Sprache und die gewählte Spracheinstellung nicht übereinstimmen, werden die Textinformationen ggf. nicht richtig angezeigt. ! Bestimmte Zeichen werden ggf. nicht ordnungsgemäß angezeigt. 1 Drehen Sie M.C., um die gewünschte Einstellung zu wählen. ENG (Englisch)—РУС (Russisch) CLOCK SET (Einstellen der Uhrzeit) 62 Bedienung des Geräts 1 Drücken Sie auf M.C., um den Einstellmodus aufzurufen. 2 Drücken Sie M.C., um den Teil der Zeitanzeige zu wählen, der eingestellt werden soll. Stunden—Minuten 3 Drehen Sie M.C., um die Uhrzeit einzustellen. 12H/24H (Uhrzeitformat) 1 Drücken Sie auf M.C., um die gewünschte Einstellung zu wählen. 12H (12-Stunden-Uhr)—24H (24-Stunden-Uhr) AUTO PI (Automatische PI-Suche) Das Gerät kann selbst bei einem Stationsabruf automatisch nach einer anderen Station mit derselben Programmierung suchen. 1 Drücken Sie M.C., um den Auto-PI-Suchlauf ein- oder auszuschalten. AUX (Zusatzeingang) Aktivieren Sie diese Einstellung, wenn ein zusätzliches, mit diesem Gerät verbundenes Gerät verwendet wird. 1 Drücken Sie M.C., um AUX ein- oder auszuschalten. MUTE MODE (Stummschaltung) Die Klangwiedergabe dieses Geräts wird automatisch stummgeschaltet oder gedämpft, wenn das Signal eines Geräts mit Stummschaltung empfangen wird. 1 Drücken Sie auf M.C., um den Einstellmodus aufzurufen. 2 Drehen Sie M.C., um die gewünschte Einstellung zu wählen. Sie können eine beliebige Option aus der folgenden Liste wählen: ! MUTE – Stummschaltung ! 20dB ATT – Dämpfung (20dB ATT hat eine stärkere Wirkung als 10dB ATT) ! 10dB ATT – Dämpfung PW SAVE (Energiesparmodus) Wenn Sie diese Funktion einschalten, reduzieren Sie den Verbrauch von Batterieleistung. ! Bei aktiviertem Energiesparmodus kann nur die Programmquelle eingeschaltet werden. 1 Drücken Sie M.C., um den Energiesparmodus ein- oder auszuschalten. Umschalten der DimmerEinstellung Sie können die Helligkeit der Beleuchtung einstellen. 1 Drücken Sie auf M.C., um das Hauptmenü anzuzeigen. 2 Drehen Sie M.C., um die Option ILLUMI zur Anzeige zu bringen, und drücken Sie dann darauf, um Ihre Auswahl zu bestätigen. 4 Drehen Sie M.C., um die GrundmenüFunktion zu wählen. Nach der Auswahl können die folgenden Grundmenüfunktionen angepasst werden. FM STEP (UKW-Kanalraster) Bei der Suchlaufabstimmung wird normalerweise das 50-kHz-UKW-Kanalraster verwendet. Wenn der Alternativfrequenzsuchlauf (AF) oder die Verkehrsmeldungen (TA) eingeschaltet sind, ändert sich das Kanalraster automatisch zu 100 kHz. Es kann jedoch vorteilhaft sein, das Kanalraster für den Alternativfrequenzsuchlauf auf 50 kHz einzustellen. ! Bei der manuellen Abstimmung bleibt das Kanalraster auf 50 kHz eingestellt. 1 Drücken Sie M.C., um die UKW-KanalrasterFunktion zu wählen. 50 (50 kHz)—100 (100 kHz) 3 Drücken Sie auf M.C., um die gewünschte Einstellung zu wählen. OFF (Aus)—ON (Ein) ! Sie können die Dimmer-Einstellung auch /DIMMER durch Drücken und Halten von ändern. Grundmenü 1 Drücken und halten Sie SRC/OFF gedrückt, bis sich das Gerät ausschaltet. 2 Drücken und halten Sie SRC/OFF gedrückt, bis das Hauptmenü im Display erscheint. 3 Drehen Sie M.C., um die Menüoption zu wechseln, und drücken Sie auf INITIAL, um die angezeigte Option zu wählen. De <QRD3143-C> 62 Black plate (63,1) Abschnitt Bedienung des Geräts SP-P/O MODE (Heckausgang- und Preout-Einstellungen) Systemmenü 2 Drücken und halten Sie SRC/OFF gedrückt, bis das Hauptmenü im Display erscheint. 3 Drehen Sie M.C., um die Menüoption zu wechseln, und drücken Sie auf SYSTEM, um die angezeigte Option zu wählen. 4 Drehen Sie M.C., um die SystemmenüFunktion zu wählen. Nach der Auswahl können die folgenden Systemmenüfunktionen angepasst werden. Für detaillierte Informationen hierzu siehe Systemmenü auf Seite 62. Verwendung der AUXProgrammquelle 1 Verbinden Sie den Stereo-Mini-Klinkenstecker mit dem AUX-Eingang. 2 Drücken Sie die Taste SRC/OFF, um AUX als Programmquelle zu wählen. 02 Bei Anzeige einer unerwünschten Anzeige Schalten Sie die unerwünschte Anzeige anhand des unten beschriebenen Vorgangs aus. 1 Drücken Sie auf M.C., um das Hauptmenü anzuzeigen. 2 Drehen Sie M.C., um die Menüoption zu wechseln, und drücken Sie auf SYSTEM, um die angezeigte Option zu wählen. 3 Drehen Sie M.C., um die Option DEMO OFF zur Anzeige zu bringen, und drücken Sie dann darauf, um Ihre Auswahl zu bestätigen. 4 Drehen Sie M.C., um zu YES umzuschalten. 5 Drücken Sie zur Auswahl M.C. Hinweis AUX kann nur gewählt werden, wenn die AUXEinstellung eingeschaltet wurde. Für weitere Einzelheiten siehe AUX (Zusatzeingang) auf Seite 62. Deutsch Der Hecklautsprecher-Leitungsausgang und Cinch-Ausgang dieses Geräts können zum Anschluss eines Vollbereichslautsprechers oder Subwoofers verwendet werden. Wählen Sie für Ihren Anschluss eine geeignete Option. 1 Drücken Sie auf M.C., um den Einstellmodus aufzurufen. 2 Drehen Sie M.C., um die gewünschte Einstellung zu wählen. Sie können eine beliebige Option aus der folgenden Liste wählen: ! REAR/SUB.W – Wählen Sie diese Option, wenn ein Vollbereichslautsprecher an den Hecklautsprecher-Leitungsausgang und ein Subwoofer an den Cinch-Ausgang angeschlossen ist. ! SUB.W/SUB.W – Wählen Sie diese Option, wenn ein Subwoofer an den Hecklautsprecher-Leitungsausgang ohne Verwendung eines zusätzlichen Verstärkers und ein Subwoofer an den Cinch-Ausgang angeschlossen ist. ! REAR/REAR – Wählen Sie diese Option, wenn ein Vollbereichslautsprecher an den Hecklautsprecher-Leitungsausgang und den Cinch-Ausgang angeschlossen ist. Wenn ein Vollbereichslautsprecher an den Hecklautsprecher-Leitungsausgang angeschlossen ist und der Cinch-Ausgang nicht verwendet wird, können Sie entweder REAR/SUB.W oder REAR/REAR auswählen. Bedienung des Geräts Umschalten der Anzeige Wählen der gewünschten Textinformationen 1 Drücken Sie auf DISP, um zwischen den folgenden Optionen umzuschalten: ! Programmquellenname ! Programmquellname und Uhr 1 Drücken und halten Sie SRC/OFF gedrückt, bis sich das Gerät ausschaltet. De <QRD3143-C> 63 63 Black plate (64,1) Abschnitt Installation 03 Installation Anschlüsse F O N OF Wichtig ! Bei der Installation des Geräts in einem Kraftfahrzeug, das am Zündschalter keine Position ACC aufweist, kann es je nach Anschlusstyp zu einer Entleerung der Fahrzeugbatterie kommen, wenn das rote Kabel nicht mit dem Anschluss verbunden wurde, der für die Erkennung des Zündschlüsselbetriebs verantwortlich ist. STAR T Zündung mit Position ACC Zündung ohne Position ACC ! Der Einsatz dieses Geräts in einer anderen als der nachstehend angegebenen Betriebsumgebung kann einen Brand auslösen oder eine Funktionsstörung zur Folge haben: — Kraftfahrzeuge mit 12-Volt-Batterie und negativer Erdung. — Lautsprecher mit 50 W (Ausgabe) und 4 W bis 8 W (Impedanz). ! Um Kurzschluss, Überhitzung oder Funktionsstörungen zu vermeiden, halten Sie sich stets an die nachstehend aufgeführten Anweisungen: — Trennen Sie die Verbindung zur negativen Anschlussklemme der Fahrzeugbatterie, bevor Sie das Gerät installieren. — Sichern Sie die Kabel mit Kabelklemmen oder Klebeband. Zum Schutz der Verkabelung sollten die Kabel an allen Stellen, an denen sie mit Metallteilen in Berührung kommen, mit Isolierband umwickelt werden. — Bringen Sie die Kabel in sicherer Entfernung von beweglichen Fahrzeugkomponenten, wie z. B. Schalthebel und Sitzschienen, an. — Bringen Sie die Kabel in größtmöglicher Entfernung von Stellen an, die sich erhitzen, wie z. B. die Heizungsöffnung. 64 — Führen Sie das gelbe Batteriekabel nicht durch ein Loch in den Motorraum, um die Verbindung mit der Fahrzeugbatterie herzustellen. — Kleben Sie freie Kabelanschlüsse mit Isolierband ab. — Kürzen Sie die Kabel nicht. — Entfernen Sie niemals die Isolierung des Stromkabels dieses Geräts, um die Stromzufuhr mit einem anderen Gerät zu teilen. Dadurch wird die Stromversorgungsleistung des Kabels beeinträchtigt. — Verwenden Sie eine Sicherung, die den vorgegebenen Leistungsmerkmalen entspricht. — Verdrahten Sie das negative Lautsprecherkabel niemals direkt mit der Erde. — Gruppieren Sie niemals die negativen Kabel mehrerer Lautsprecher. ! Wenn dieses Gerät eingeschaltet wird, liegen Steuersignale am blau/weißen Kabel an. Verbinden Sie dieses Kabel mit der Systemfernbedienung eines externen Leistungsverstärkers oder der Steuerklemme des Automatikantennenrelais des Kraftfahrzeugs (max. 300 mA, 12 V Gleichspannung). Wenn das Fahrzeug mit einer in die Heckscheibe integrierten Radioantenne ausgestattet ist, verbinden Sie das Kabel mit der Versorgungsklemme des Antennenboosters. ! Verbinden Sie das blau/weiße Kabel niemals mit der Leistungsklemme des externen Leistungsverstärkers. Darüber hinaus darf das Kabel keinesfalls mit der Leistungsklemme der Fahrzeugantenne verbunden werden. Andernfalls kann es zu einer Entleerung oder Funktionsstörung der Fahrzeugbatterie kommen. ! Das schwarze Kabel gewährleistet die Erdung. Dieses Kabel wie auch die Erdungskabel anderer Produkte (insbesondere von Hochstromprodukten wie Leistungsverstärker) müssen separat verdrahtet werden. Anderenfalls kann es zu einem Brand oder einer Funktionsstörung kommen, wenn sich die Kabel versehentlich lösen. Netzkabel 2 Dieses Gerät 1 2 7 3 4 5 6 3 4 5 6 1 8 a 3 1 2 3 4 5 4 5 Netzkabelzugang Heck- oder Subwooferausgang Antenneneingang Sicherung (10 A) Eingang der festverdrahteten Fernbedienung Es besteht die Möglichkeit, einen (separat erhältlichen) festverdrahteten Fernbedienungsadapter anzuschließen. 9 e b c d 1 Zum Netzzugang 2 Je nach Fahrzeugtyp können die Funktionen 3 und 5 variieren. Stellen Sie in diesem Fall sicher, dass der Anschluss von 4 nach 5 und 6 nach 3 erfolgt. 3 Gelb Reserveversorgung (oder Zubehör) 4 Gelb Verbindung mit der Klemme der konstanten 12-V-Spannungsversorgung. 5 Rot Zubehör (oder Reserveversorgung) 6 Rot Verbindung mit der Klemme der zündungsgesteuerten Spannungsversorgung (12 V Gleichspannung). 7 Verbinden Sie jeweils Anschlüsse derselben Farbe miteinander. 8 Schwarz (Fahrgestell-Erdung) De <QRD3143-C> 64 Black plate (65,1) Abschnitt Installation Hinweise ! Ändern Sie das Grundeinstellmenü dieses Geräts. Siehe SP-P/O MODE (Heckausgangund Preout-Einstellungen) auf Seite 63. Die Subwoofer-Ausgabe dieses Geräts erfolgt in Mono. ! Bei Verwendung eines 70-W-Subwoofers (2 W) muss sichergestellt werden, dass der Subwoofer am violetten und violett/schwarzen-Anschluss dieses Geräts angeschlossen wird. Schließen Sie nichts an den grünen und grün/schwarzen-Anschluss an. 03 ! Der Halbleiterlaser kann durch Überhitzung beschädigt werden. Installieren Sie dieses Gerät deshalb in sicherer Entfernung von Hitzequellen, wie z. B. Heizöffnungen. ! Optimale Leistung kann durch eine Installation des Geräts in einem Winkel unter 60° erzielt werden. Leistungsverstärker (separat erhältlich) 60° Führen Sie diese Verkabelungen beim Gebrauch eines optionalen Verstärkers durch. 3 1 5 2     4 5 1 Systemfernbedienung Verbindung mit blau/weißem Kabel. 2 Leistungsverstärker (separat erhältlich) 3 Verbindung mit Cinch-Kabeln (separat erhältlich) 4 Zum Heck- oder Subwooferausgang 5 Hecklautsprecher oder Subwoofer ! Um beim Gebrauch des Geräts eine ordnungsgemäße Wärmezerstreuung zu gewährleisten, ist bei der Installation genügend Freiraum hinter der Rückseite vorzusehen. Lose Kabel sind aufzuwickeln, damit sie die Lüftung nicht behindern. 1 Führen Sie den Montagerahmen in das Armaturenbrett ein. Verwenden Sie den mitgelieferten Montagerahmen, wenn bei der Installation wenig Platz zur Verfügung steht. Bei ausreichendem Platz kann der mit dem Fahrzeug mitgelieferte Montagerahmen verwendet werden. 2 Befestigen Sie den Montagerahmen mithilfe eines Schraubendrehers: Die Metallklammern sind in eine sichere Position (90°) zu biegen. 1 2 Reichlich Platz lassen 5 cm 5 cm 5cm cm Installation Wichtig ! Überprüfen Sie vor der endgültigen Installation alle Anschlüsse und Systeme. ! Die Verwendung nicht zugelassener Teile kann eine Funktionsstörung zur Folge haben. ! Wenden Sie sich an Ihren Fachhändler, wenn für die Installation Löcher gebohrt oder andere Änderungen am Fahrzeug vorgenommen werden müssen. ! Installieren Sie dieses Gerät keinesfalls an folgenden Orten: DIN-Frontmontage Front-/Rückmontage nach DIN Dieses Gerät kann sowohl über die Front- als auch über die Rückmontage installiert werden. Verwenden Sie für die Montage im Handel erhältliches Zubehör. 1 Armaturenbrett 2 Montagerahmen # Stellen Sie sicher, dass das Gerät fest angebracht ist. Ein instabiler Einbau kann zum Aussetzen von Tönen führen oder andere Fehlfunktionen verursachen. Deutsch 9 Blau/Weiß Die Pin-Position des ISO-Anschlusses variiert je nach Fahrzeugtyp. Wird Pin 5 zur Steuerung der Antenne verwendet, verbinden Sie 9 und b. Verbinden Sie in jedem anderen Fahrzeugtyp niemals 9 und b. a Blau/Weiß Verbindung mit der Systemsteuerungsklemme des Leistungsverstärkers (max. 300 mA, 12 V Gleichspannung). b Blau/Weiß Verbindung mit der Steuerungsklemme des Automatikantennenrelais (max. 300 mA 12 V Gleichspannung). c Gelb/Schwarz Wenn Sie ein Gerät mit Stummschaltfunktion verwenden, verbinden Sie diesen Draht mit dem Draht der Audio-Stummschaltung dieses Geräts. Andernfalls sollte der Draht der Audio-Stummschaltung (Mute) frei bleiben. d Lautsprecherkabel Weiß: Vorn links + Weiß/Schwarz: Vorn links * Grau: Vorn rechts + Grau/Schwarz: Vorn rechts * Grün: Hinten links + oder Subwoofer + Grün/Schwarz: Hinten links * oder Subwoofer * Violett: Hinten rechts + oder Subwoofer + Violett/Schwarz: Hinten rechts * oder Subwoofer * e ISO-Anschluss Bei manchen Fahrzeugtypen kann der ISOAnschluss zweigeteilt sein. Stellen Sie in diesem Fall sicher, dass zu beiden Anschlüssen Verbindungen hergestellt werden. Installation DIN-Rückmontage 1 Bestimmen Sie die geeignete Position, damit die Löcher an der Klammer und den Geräteseiten ordnungsgemäß ausgerichtet sind. — Orte, an denen das Gerät die Steuerung des Fahrzeugs behindern könnte. — Orte, an denen das Gerät die Insassen des Fahrzeugs im Anschluss an eine Schnellbremsung verletzen könnte. De <QRD3143-C> 65 65 Black plate (66,1) Abschnitt Installation 03 Zusätzliche Informationen 2 Ziehen Sie auf jeder Seite zwei Schrauben fest. 3 Ziehen Sie das Gerät aus dem Armaturenbrett. 2 1 Blechschraube (5 × 8 mm) 2 Montageklammer 3 Armaturenbrett oder Konsole Entfernen des Geräts Entfernen Sie den Einpassungsring. 1 Einpassungsring 2 Aussparung ! Bei entriegelter Bedienfläche lässt sich der Einpassungsring einfacher erreichen. ! Halten Sie beim Wiederanbringen des Einpassungsrings die Seite mit der Aussparung nach unten. 2 Führen Sie die mitgelieferten Extraktionsschlüssel an beiden Geräteseiten ein, bis sie in der richtigen Position einrasten. 66 Symptom Ursache Abhilfemaßnahme Das Display schaltet automatisch in die normale Anzeige um. Sie haben keinen Bedienvorgang innerhalb von 30 Sekunden durchgeführt. Wiederholen Sie den Vorgang. Der Wiederholbereich ändert sich unerwartet. Ja nach Wieder- Wählen Sie den holbereich kann Wiederholbereich sich der ausge- erneut aus. wählte Bereich ändern, sobald ein anderer Ordner oder Musiktitel ausgewählt wird oder während des schnellen Vorund Rücklaufs. 3 1 1 Fehlerbehebung Abnehmen und Wiederanbringen der Frontplatte Sie können die Frontplatte zum Schutz vor Diebstahl abnehmen. Drücken Sie die Taste zum Entriegeln der Frontplatte und schieben Sie sie nach oben und auf Sie zu. Detaillierte Informationen hierzu finden Sie unter Entfernen der Frontplatte zum Schutz vor Diebstahl und Wiederanbringen der Frontplatte auf Seite 58. Ein Unterordner wird nicht wiedergegeben. Unterordner können nicht wiedergegeben werden, wenn FLD (OrdnerWiederholung) ausgewählt ist. Wählen Sie einen anderen Wiederholbereich. NO XXXX er- Es sind keine Schalten Sie die scheint, wenn Textinformatio- Anzeige um oder sich die Annen eingebettet. spielen Sie einen zeige ändert anderen Titel bzw. (z. B. NO eine andere Datei TITLE). ab. Symptom Ursache Abhilfemaßnahme Im Gerät ist eine Fehlfunktion aufgetreten. Es liegen Funkstörungen vor. Sie verwenden in der Nähe dieser Einheit ein Gerät, wie z. B. ein Mobiltelefon, welches elektromagnetische Frequenzen aussendet. Lassen Sie einen ausreichenden Abstand zwischen dieser Einheit und den Geräten, die die Funkstörung verursachen. Fehlermeldungen Vor der Kontaktaufnahme mit Ihrem Händler oder der nächstgelegenen Pioneer-Kundendienststelle sollten Sie sich die angezeigte Fehlermeldung notieren. Allgemeines Meldung Ursache Abhilfemaßnahme AMP ERROR Betriebsstörung des Geräts oder falsche Lautsprecherverbindung; Schutzschaltung ist aktiviert. Überprüfen Sie die Lautsprecherverbindung. Wenn die Meldung selbst nach dem Aus-/Einschalten des Motors weiterhin angezeigt wird, wenden Sie sich zur Unterstützung an Ihren Händler oder eine PioneerKundendienststelle. De <QRD3143-C> 66 Black plate (67,1) Anhang Zusätzliche Informationen CD-Player Meldung Ursache ERROR-07, Die Disc ist ver11, 12, 17, 30 schmutzt. ERROR-07, 10, 11, 12, 15, 17, 30, A0 Abhilfemaßnahme Reinigen Sie die Disc. Die Disc ist verkratzt. Wechseln Sie die Disc aus. Es liegt ein elektrischer oder mechanischer Fehler vor. Schalten Sie die Zündung aus (OFF) und wieder ein (ON) oder schalten Sie auf eine andere Programmquelle um und dann wieder zum CD-Player zurück. Die eingelegte Disc ist leer. ERROR-23 Nicht unterWechseln Sie die stütztes CD-For- Disc aus. mat. FORMAT READ Nach dem Wiedergabestart ist der Ton in manchen Fällen erst nach einer Verzögerung zu hören. Meldung Ursache Abhilfemaßnahme PROTECT Alle Dateien auf Wechseln Sie die der eingelegten Disc aus. Disc weisen einen DRMSchutz (digitale Rechteverwaltung) auf. Handhabungsrichtlinien Discs und Player Verwenden Sie ausschließlich Discs, die eines der folgenden zwei Logos aufweisen: Wechseln Sie die Disc aus. Warten Sie bis die Anzeige erlischt und Sie einen Ton hören. NO AUDIO Die eingelegte Wechseln Sie die Disc enthält Disc aus. keine abspielbaren Dateien. SKIPPED Wechseln Sie die Die eingelegte Disc enthält Da- Disc aus. teien mit DRMSchutz (digitale Rechteverwaltung). Verwenden Sie 12-cm-Discs. 8-cm-Discs bzw. Adapter für 8-cm-Discs dürfen nicht verwendet werden. Verwenden Sie ausschließlich herkömmliche, runde Discs. Discs einer anderen Form sollten nicht verwendet werden. In den CD-Ladeschacht darf kein anderer Gegenstand als eine CD eingeführt werden. CD-R/RW-Discs, deren Aufzeichnungen nicht abgeschlossen (finalisiert) wurden, können nicht abgespielt werden. Berühren Sie unter keinen Umständen die DiscOberfläche mit den aufgezeichneten Daten. Bewahren Sie die Discs bei Nichtgebrauch in deren Hülle auf. Kleben Sie keine Etiketten auf Discs, beschriften Sie sie nicht und wenden Sie keine Chemikalien auf die Disc-Oberfläche an. Wischen Sie die Discs zum Reinigen mit einem weichen Tuch von der Mitte zum Rand hin ab. Kondensation kann eine vorübergehende Störung der Player-Leistung zur Folge haben. Warten Sie in diesem Fall etwa eine Stunde ab, bis sich der Player an die höheren Temperaturen angepasst hat. Zudem sollten feuchte Discs mit einem weichen Tuch trockengerieben werden. Unter Umständen ist eine Disc-Wiedergabe nicht möglich. Das kann auf die spezifischen Eigenschaften der Disc, das Disc-Format, die für die Aufzeichnung verwendete Software, die Wiedergabeumgebung, die Lagerbedingungen usw. zurückzuführen sein. Erschütterungen aufgrund von Unebenheiten der Fahrbahn können die Disc-Wiedergabe unterbrechen. Lesen Sie sich vor der Verwendung von Discs die Disc-spezifischen Sicherheitshinweise durch. Bei Verwendung von bedruckbaren Discs, beachten Sie die Anleitung und die Warnhinweise der Disc. Je nach Beschaffenheit der Discs, können Sie eventuell nicht eingelegt oder ausgeworfen werden. Die Verwendung solcher Discs kann zu einer Beschädigung dieses Gerätes führen. Bringen Sie keine handelsüblichen Etiketten oder andere Materialien auf den Discs an. ! Die Discs können sich verformen und werden nicht wiedergegeben. ! Die Etiketten können sich während der Wiedergabe lösen und den Auswurf behindern, wodurch das Gerät beschädigt werden könnte. DualDiscs DualDiscs sind doppelseitige Discs, die eine beschreibbare CD-Seite für Audio- und eine beschreibbare DVD-Seite für Video-Daten bereitstellen. Da die CD-Seite von DualDiscs physikalisch nicht mit dem allgemeinen CD-Standard kompatibel ist, ist eine Wiedergabe der CD-Seite mit diesem Gerät ggf. nicht möglich. Das häufige Einlegen und Auswerfen einer DualDisc kann zu Kratzern auf der Disc führen, die wiederum, wenn sie besonders ausgeprägt sind, Probleme bei der Wiedergabe auf diesem Gerät zur Folge haben können. In manchen Fällen kann es sogar vorkommen, dass eine DualDisc im Disc-Ladeschacht eingeklemmt wird und nicht mehr ausgeworfen werden kann. Um dies zu vermeiden, wird empfohlen, von der Verwendung von DualDiscs mit diesem Gerät abzusehen. Detaillierte Angaben zu DualDiscs können Sie den vom Hersteller der Disc bereitgestellten Informationen entnehmen. Deutsch ERROR-15 Zusätzliche Informationen Verwenden Sie keinesfalls Discs, die Sprünge, Einkerbungen/Absplitterungen, Verformungen oder andere Beschädigungen aufweisen, da Sie dadurch den Player beschädigen könnten. De <QRD3143-C> 67 67 Black plate (68,1) Anhang Zusätzliche Informationen Kompatibilität mit AudioKompression WMA Dateierweiterung: .wma Bitrate: 48 Kbit/s bis 320 Kbit/s (CBR - Konstante Bitrate), 48 Kbit/s bis 384 Kbit/s (VBR - Variable Bitrate) Abtastfrequenz: 32 kHz; 44,1 kHz; 48 kHz Windows Media Audio Professional, Lossless, Voice/DRM Stream/Stream mit Video: Nicht kompatibel MP3 Zusätzliche Informationen Zusätzliche Informationen Von Dateinamen (einschließlich der Dateierweiterung) bzw. von Ordnernamen können jeweils nur die ersten 32 Zeichen angezeigt werden. Damit kyrillische Buchstaben auf diesem Gerät angezeigt werden können, müssen diese mit einem der folgenden Zeichensätze codiert worden sein: ! Unicode (UTF-8, UTF-16) ! Andere Zeichensätze als Unicode, die in einer Windows-Umgebung verwendet und in den Sprachoptionen auf Russisch eingestellt wurden. Reihenfolge der Audio-Dateien Der Benutzer kann keine Ordnernummern zuweisen und auch die Wiedergabereihenfolge mit diesem Gerät nicht bestimmen. Beispiel einer Datenträger-Struktur 1 2 03 3 4 04 Abtastfrequenz: 8 kHz bis 48 kHz (32 kHz; 44,1 kHz; 48 kHz für Emphase) 5 6 Kompatible ID3-Tag-Version: 1.0, 1.1, 2.2, 2.3, 2.4 (ID3-Tag-Version 2.x erhält Vorrang vor Version 1.x) Disc 05 Stufe 1 Stufe 2 Stufe 3 Stufe 4 Abspielbare Ordnerstruktur: bis zu acht Ebenen (der Einfachheit halber sollte die Ordnerstruktur jedoch aus weniger als zwei Ebenen bestehen). Abspielbare Ordner: bis zu 99 M3u-Spielliste: Nicht kompatibel Abspielbare Dateien: bis zu 999 MP3i (MP3 interaktiv), mp3 PRO: Nicht kompatibel Dateisystem: Konformität mit ISO 9660 Stufe 1 und 2, Romeo, Joliet : Ordner : Komprimierte Audio-Datei 01 bis 05: Ordnernummer 1 bis 6: Wiedergabereihenfolge Disc Die bei der Ordnerauswahl oder einem anderen Bedienvorgang angewendete Reihenfolge kann sich je nach der verwendeten Codierungs- bzw. Schreibsoftware ändern. Russischer Zeichensatz Multi-Session-Wiedergabe: Kompatibel WAV Dateierweiterung: .wav Quantisierungsbits: 8 und 16 (LPCM), 4 (MS ADPCM) Abtastfrequenz: 16 kHz bis 48 kHz (LPCM); 22,05 kHz und 44,1 kHz (MS ADPCM) 68 Datenübertragungen im Paketverfahren: Nicht kompatibel Ungeachtet der Länge der Leerstellen, die die Originalaufnahme zwischen den einzelnen Musiktiteln aufweist, wird bei der Wiedergabe von komprimierten Audio-Discs stets eine kurze Pause zwischen den Titeln eingefügt. D: C D: C D: C :Ъ :Я :Х :Ц :Ч : Ш, Щ :Ы :Ь :Э :Ю D: Anzeige C: Zeichen Copyrights und Marken Apple und iTunes sind Warenzeichen von Apple Inc., eingetragen in den USA und anderen Ländern. 02 Je nach der Anwendung, die für die Codierung der WMA-Dateien verwendet wurde, funktioniert dieses Gerät ggf. nicht ordnungsgemäß. D: C iTunes 01 Dateierweiterung: .mp3 Bitrate: 8 Kbit/s bis 320 Kbit/s (CBR), VBR D: C VORSICHT Bewahren Sie Discs nicht an Orten mit hohen Temperaturen auf. MP3 Die Bereitstellung dieses Produkts erfolgt in Verbindung mit einer Lizenz zur privaten, nichtkommerziellen Nutzung und impliziert weder die Übertragung einer Lizenz noch die Einräumung eines Rechts zur Verwendung dieses Produkts in kommerziellen (d. h. ertragsorientierten) LiveProgrammen (leitungsbasiert, per Satellit, Kabel und/oder über jedes beliebige andere Medium), zum Broadcasting/Streaming über das Internet, über Intranets und/oder andere Netzwerke oder in anderen elektronischen Inhalt-Vertriebssystemen, z. B. „Pay-Audio”- oder „Audio-on-demand”-Anwendungen. Für eine derartige Nutzung ist eine separate Lizenz erforderlich. Detaillierte Informationen hierzu finden Sie unter http://www.mp3licensing.com. D: C D: C D: C D: C D: C :А :Б :В :Г :Д : Е, Ё :Ж :З : И, Й :К WMA :Л :М :Н :О :П :Р :С :Т :У :Ф Windows Media ist eine eingetragene Marke oder eine Marke der Microsoft Corporation in den USA und/oder anderen Ländern. Dieses Produkt enthält Technologie, die Eigentum der Microsoft Corporation ist und nicht ohne Lizenz von Microsoft Licensing, Inc. vertrieben werden darf. De <QRD3143-C> 68 Black plate (69,1) Anhang Zusätzliche Informationen Technische Daten Allgemein Stromversorgung ............. 14,4 V Gleichspannung (Toleranz 10,8 V bis 15,1 V) Erdungssystem ................ Negativ Maximale Leistungsaufnahme ................................... 10,0 A Abmessungen (B × H × T): DIN Einbaugröße ...... 178 mm × 50 mm × 165 mm Frontfläche ........ 188 mm × 58 mm × 16 mm D Einbaugröße ...... 178 mm × 50 mm × 165 mm Frontfläche ........ 170 mm × 46 mm × 16 mm Gewicht ........................... 1 kg Audio Compact Disc 94 dB (1 kHz) (IEC-A-Netz) 2 (Stereo) MPEG-1 und 2 Audio Layer 3 Vers. 7, 7.1, 8, 9, 10, 11, 12 (2Kanal-Audio) (Windows Media Player) WAV-Signalformat ............ Lineare PCM und MS ADPCM (nicht komprimiert) UKW-Tuner Frequenzbereich .............. 87,5 MHz bis 108,0 MHz Nutzempfindlichkeit ......... 9 dBf (0,8 µV/75 W, Mono, Signal-Rauschabstand: 30 dB) Signal-Rauschabstand ..... 72 dB (IEC-A-Netz) MW-Tuner Frequenzbereich .............. 531 kHz bis 1 602 kHz Nutzempfindlichkeit ......... 25 µV (Signal-Rauschabstand: 20 dB) Signal-Rauschabstand ..... 62 dB (IEC-A-Netz) LW-Tuner Frequenzbereich .............. 153 kHz bis 281 kHz Nutzempfindlichkeit ......... 28 µV (Signal-Rauschabstand: 20 dB) Signal-Rauschabstand ..... 62 dB (IEC-A-Netz) Deutsch Max. Ausgangsleistung .... 50 W × 4 70 W × 1/2 W (für Subwoofer) Dauer-Ausgangsleistung ................................... 22 W × 4 (50 Hz bis 15 000 Hz, 5 % THD, bei 4-W-Last, beide Kanäle betrieben) Lastimpedanz .................. 4 W (4 W bis 8 W zulässig) Maximaler Preout-Ausgangspegel ................................... 2,0 V Loudness-Kontur ............. +10 dB (100 Hz), +6,5 dB (10 kHz) (Lautstärke: –30 dB) Equalizer (5-Band Graphic Equalizer): Frequenz ................... 80 Hz/250 Hz/800 Hz/ 2,5 kHz/8 kHz Entzerrungsbereich ............................ ±12 dB (Inkrement 2 dB) Subwoofer (Mono): Frequenz ................... 50 Hz/63 Hz/80 Hz/100 Hz/ 125 Hz/160 Hz/200 Hz Steilheit .................... –6 dB/Okt., –12 dB/Okt. Verstärkung .............. +6 dB bis –24 dB Phase ....................... Normal/Gegen Kompatible Discs ............. Signal-Rauschabstand ..... Anzahl der Kanäle ............ MP3-Decodiermodus ....... WMA-Decodiermodus ...... Hinweis Änderungen der technischen Daten und des Designs vorbehalten. CD-Player Typ ................................... Compact-Disc-Digital-Audiosystem De <QRD3143-C> 69 69 Black plate (70,1) Hoofdstuk Vóór u begint 01 Hartelijk dank voor uw keuze voor dit Pioneer-product. Lees deze handleiding voordat u het product in gebruik neemt zodat u het goed leert gebruiken. Lees vooral de gedeelten die met WAARSCHUWING en LET OP gemarkeerd zijn aandachtig. Bewaar deze handleiding na het lezen op een veilige, voor de hand liggende plaats zodat u hem indien nodig altijd kunt raadplegen. Vóór u begint Informatie over dit toestel Bij problemen De tuner van dit toestel kan worden afgestemd op frequenties die gebruikt worden in West-Europa, Azië, het Midden-Oosten, Afrika en Oceanië. In andere gebieden is de ontvangst wellicht slecht. De RDS-functie (Radio Data System) werkt alleen in gebieden waar FM-zenders RDSinformatie uitzenden. Als dit toestel niet naar behoren functioneert, kunt u uw leverancier of het dichtstbijzijnde erkende Pioneer-servicecentrum raadplegen. LET OP Dit apparaat is geclassificeerd als een klasse 1 laserproduct onder de veiligheidsnormen voor laserproducten, IEC 60825-1:2007. Deponeer dit product niet bij het gewone huishoudelijk afval wanneer u het wilt verwijderen. Er bestaat een speciaal wettelijk voorgeschreven verzamelsysteem voor de juiste behandeling, het opnieuw bruikbaar maken en de recycling van gebruikte elektronische producten. In de lidstaten van de EU en in Zwitserland en Noorwegen kunnen particulieren afgedankte elektronische producten gratis bij de daarvoor bestemde verzamelplaatsen inleveren. Als u een soortgelijk nieuw product koopt, kunt u het afgedankte product ook bij uw verkooppunt inleveren. Als u in een ander land woont, neem dan contact op met de plaatselijke overheid voor informatie over het weggooien van afgedankte producten. Op die manier zorgt u ervoor dat uw afgedankte product op de juiste wijze wordt verwerkt, hergebruikt en gerecycled, zonder schadelijke gevolgen voor het milieu en de volksgezondheid. 70 KLASSE 1 LASERPRODUCT LET OP ! Zorg ervoor dat het toestel niet met vloeistof in aanraking komt. Een elektrische schok kan daarvan het gevolg zijn. Bovendien kan contact met vloeistoffen rookvorming, oververhitting en andere schade aan het toestel veroorzaken. ! De Pioneer CarStereo-Pass wordt alleen in Duitsland gebruikt. ! Zet het volume nooit zo hoog dat u geluiden buiten het voertuig niet meer kunt horen. ! Zorg dat het toestel niet wordt blootgesteld aan vocht. ! Als de accu wordt losgekoppeld of leeg raakt, wordt het voorkeuzegeheugen gewist. Opmerking Instellingen worden ook uitgevoerd als u het menu annuleert zonder te bevestigen. Nl <QRD3143-C> 70 Black plate (71,1) Hoofdstuk Bediening van het toestel Bediening van het toestel Hoofdtoestel Indicator 1 2 34 5 6 7 8 1 9 a b Onderdeel 1 h (uitwerpen) 8 BAND 2 SRC/OFF 9 (terug)/DIMMER (dimmer) 3 MULTI-CONTROL (M.C.) a c/d b 1/ c AUX-ingang (3,5 mm-stereoplug) 4 (lijst) 5 DISP 6 Laadsleuf voor disc 7 (equalizer) d tot 6/ Verwijderen Display-indicaties 2 3 9 Hier wordt bijkomende informatie weergegeven. 3 TA (verkeersberichten) Automatische ontvangst van verkeersberichten (TA) is ingeschakeld. 4 TP (verkeersprogrammaidentificatie) Er is afgestemd op een zender met verkeersinformatie (TPzender). a De sound retriever is ingeschakeld. (sound retriever) 6 LOC Automatisch afstemmen op lokale zenders is ingeschakeld. 7 (herhalen) Herhalen van een fragment of map is ingeschakeld. 8 (willekeurig) Willekeurige weergave is ingeschakeld. Basisinformatie ! Tuner: frequentieband en frequentie ! RDS: programmaservicenaam, PTY-informatie en andere tekstinformatie ! Cd-speler: verstreken weergavetijd en tekstinformatie a Als u het contact aanzet na de installatie, verschijnt het instellingenmenu op het display. U kunt de onderstaande menu-opties instellen. 1 Zet het contact aan na de installatie van dit toestel. SET UP verschijnt. 2 5 6 8 5 7 Instellingenmenu Licht op wanneer er een menu of mappen op een lager niveau bestaan. Draai aan M.C. en selecteer YES. # Als u niet binnen 30 seconden een bediening uitvoert, wordt het instellingenmenu niet weergegeven. # Als u op dit moment geen instellingen wilt maken, draait u M.C. naar NO. Indrukken om te selecteren. Als u NO selecteert, kunt u geen instellingen maken in het instellingenmenu. 3 Druk op M.C. om uw keuze te bevestigen. 4 Voer de volgende procedures uit om het menu in te stellen. Om verder te gaan naar de volgende menuoptie, moet u uw selectie bevestigen. LANGUAGE (taalinstelling) Dit toestel kan Engelse of Russische tekstinformatie bij een gecomprimeerd audiobestand weergeven. ! Als de gebruikte taal niet overeenkomt met de taalinstelling van dit toestel, wordt tekst wellicht niet correct weergegeven. ! Het is mogelijk dat sommige tekens niet juist worden weergegeven. 1 Draai aan M.C. en selecteer de gewenste instelling. ENG (Engels)—РУС (Russisch) 2 Druk op M.C. om de selectie te bevestigen. CLOCK SET (klok) 1 2 3 4 Draai aan M.C. om het uur in te stellen. Druk op M.C. om de minuut te selecteren. Draai aan M.C. om de minuut in te stellen. Druk op M.C. om de selectie te bevestigen. FM STEP (FM-afstemstap) Standaard wordt er bij automatisch afstemmen een FM-afstemstap van 50 kHz gebruikt, en 100 kHz als de functie AF of TA is ingeschakeld. Maar soms krijgt u een beter resultaat als ook bij het afstemmen op alternatieve frequenties (AF) een afstemstap van 50 kHz wordt gebruikt. ! Bij handmatig afstemmen blijft de afstemstap 50 kHz. 1 Draai aan M.C. en selecteer de FM-afstemstap. 50 (50 kHz)—100 (100 kHz) 2 Druk op M.C. om de selectie te bevestigen. QUIT verschijnt. 5 Draai aan M.C. en selecteer YES om de instelling te voltooien. # Als u de instelling wilt wijzigen, draait u M.C. naar NO. Druk in om te selecteren. 6 Druk op M.C. om uw keuze te bevestigen. Opmerkingen ! U kunt de menu-opties instellen in het systeemmenu. Raadpleeg Systeemmenu op bladzijde 75 voor meer informatie over de instellingen. ! U kunt het instellingenmenu annuleren door op SRC/OFF te drukken. Nederlands 1 Bijkomende informatie 9 4 De lijst wordt bediend. 2 c d Onderdeel (lijst) Status 02 Basisbediening Belangrijk ! Wees voorzichtig bij het verwijderen en terugplaatsen van het voorpaneel. ! Stel het voorpaneel niet bloot aan schokken. Nl <QRD3143-C> 71 71 Black plate (72,1) Hoofdstuk Bediening van het toestel 02 ! Stel het voorpaneel niet bloot aan direct zonlicht en hoge temperaturen. ! Maak eerst alle kabels en apparaten (indien aanwezig) van het voorpaneel los voordat u het verwijdert om beschadiging aan het toestel en het voertuiginterieur te voorkomen. Het voorpaneel tegen diefstal verwijderen 1 Druk op de toets Verwijderen om het voorpaneel los te maken. 2 Duw het voorpaneel naar boven (M) en trek het naar u toe (N). Bediening van het toestel Het toestel uitschakelen 1 Houd SRC/OFF ingedrukt tot het toestel uit gaat. Een frequentieband selecteren 1 Druk op BAND totdat de gewenste frequentieband (FM1, FM2, FM3 voor FM of MW/LW) wordt weergegeven. Het volume afstellen 1 Draai aan M.C. om het volume te regelen. Overschakelen tussen voorkeuzestations 1 Druk op c of d. ! Om deze functie te gebruiken, moet u PCH (voorkeuzezender) selecteren onder SEEK. Raadpleeg voor meer informatie over de instellingen SEEK (instelling linker/rechter toets) op de volgende bladzijde. Voor uw veiligheid en die van anderen moet u het voertuig eerst parkeren als u het voorpaneel wilt verwijderen. Het voorpaneel terugzetten 1 Schuif het voorpaneel naar links. Steek de lipjes aan de linkerzijde van het hoofdtoestel goed in de openingen in het voorpaneel. Opmerking Als de blauw-witte draad van dit toestel is aangesloten op de bedieningsaansluiting van de automatische antenne van het voertuig, schuift de antenne uit wanneer er een signaalbron van dit toestel wordt ingeschakeld. Als de signaalbron wordt uitgeschakeld, wordt de antenne weer ingeschoven. Veelgebruikte menufuncties 2 Druk de rechterzijde van het voorpaneel aan tot het goed geplaatst is. Als het niet lukt het voorpaneel te bevestigen, controleer dan of u het wel juist op het hoofdtoestel bevestigt. Gebruik geen kracht want daardoor kunt u het paneel en het toestel beschadigen. Het toestel inschakelen 1 Druk op SRC/OFF om het toestel in te schakelen. 72 Basisbediening Een signaalbron selecteren 1 Druk op SRC/OFF om over te schakelen tussen: TUNER (tuner)—CD (cd-speler)—AUX (AUX) LET OP 3 Bewaar het losgemaakte voorpaneel in een beschermend omhulsel zoals een stevig doosje. Tuner Terugkeren naar het vorige display Terugkeren naar de vorige lijst (de map die een niveau hoger ligt) 1 Druk op /DIMMER. Terugkeren naar het gewone display Het hoofdmenu annuleren 1 Druk op BAND. Terugkeren naar het gewone display van de lijst 1 Druk op BAND. Handmatig afstemmen (stap voor stap) 1 Druk op c of d. ! Om deze functie te gebruiken, moet u MAN (handmatig afstemmen) selecteren onder SEEK. Raadpleeg voor meer informatie over de instellingen SEEK (instelling linker/rechter toets) op de volgende bladzijde. Automatisch afstemmen 1 Houd c of d ingedrukt en laat deze weer los. U kunt het automatisch afstemmen afbreken door even op c of d te drukken. Als u c of d ingedrukt houdt, worden zenders overgeslagen. Het automatisch afstemmen begint zodra u c of d loslaat. Opmerking U kunt de AF-functie (zoeken naar alternatieve frequenties) in- en uitschakelen. Voor normaal afstemmen moet de AF-functie uit staan (raadpleeg AF (alternatieve frequenties zoeken) op de volgende bladzijde). Zenders voor de verschillende frequentiebanden opslaan en oproepen De voorkeuzetoetsen gebruiken 1 Stem af op de zender die u in het geheugen wilt opslaan. Om hem op te slaan houdt u de gewenste voorkeuzetoets (1/ t/m 6/ ) ingedrukt tot het voorkeuzenummer stopt met knipperen. 2 Druk op de gewenste voorkeuzetoets (1/ t/m 6/ ) om de betreffende zender te selecteren. Een ander display kiezen De gewenste informatie selecteren 1 Druk op DISP om over te schakelen tussen: ! FREQUENCY (programmaservicenaam of frequentie) ! BRDCST INFO (programmaservicenaam/ PTY-informatie) ! CLOCK (naam signaalbron en klok) Opmerkingen ! Als de programmaservicenaam niet gedetecteerd kan worden in FREQUENCY, wordt de frequentie weergegeven. Anders wordt de programmaservicenaam weergegeven. ! De tekstinformatie onder BRDCST INFO wordt automatisch bijgewerkt. ! Afhankelijk van de frequentieband kan de tekstinformatie verschillen. ! Welke tekstinformatie gewijzigd kan worden, hangt af van het gebied. PTY-functies Met behulp van PTY-informatie (programmatypeinformatie) kunt u op een bepaald soort zender afstemmen. Nl <QRD3143-C> 72 Black plate (73,1) Hoofdstuk Bediening van het toestel RDS-zenders zoeken via PTY-informatie U kunt naar bepaalde soorten uitzendingen zoeken, zoals de uitzendingen die in het volgende gedeelte worden genoemd: deze bladzijde. (lijst). 1 Druk op 2 Draai aan M.C. om een programmatype te kiezen. NEWS/INFO—POPULAR—CLASSICS— OTHERS 3 Druk op M.C. om het zoeken te beginnen. Het toestel zoekt naar een zender die het geselecteerde programmatype uitzendt. Als er een zender is gevonden, wordt de programmaservicenaam weergegeven. ! Druk opnieuw op M.C. om het zoeken te annuleren. ! Het programma van een zender kan afwijken van de informatie die door de PTY-code wordt aangegeven. ! Als er geen zender gevonden wordt die het gewenste soort programma uitzendt, wordt op het display ongeveer twee seconden lang NOT FOUND getoond en keert de tuner terug naar de oorspronkelijke zender. Bediening van het toestel OTHERS (andere) EDUCATE (educatief), DRAMA (theater), CULTURE (cultuur), SCIENCE (wetenschap), VARIED (varia), CHILDREN (kinderprogramma’s), SOCIAL (praatprogramma’s), RELIGION (religieus), PHONE IN (inbelprogramma’s), TOURING (reizen), LEISURE (ontspanning), DOCUMENT (documentaires) Functie-instellingen 1 Druk op M.C. om het hoofdmenu weer te geven. 2 Draai aan M.C., selecteer de menuoptie FUNCTION en druk erop. 3 Draai aan M.C. om de gewenste functie te selecteren. U kunt de volgende functies aanpassen. # Als de MW/LW-band is geselecteerd, zijn alleen BSM, LOCAL en SEEK beschikbaar. Als deze functie is ingeschakeld, stemt het toestel alleen af op zenders waarvan het signaal voldoende sterk is voor een goede ontvangst. 1 Druk op M.C. en selecteer de gewenste instelling. FM: OFF—LV1—LV2—LV3—LV4 MW/LW: OFF—LV1—LV2 Als u het hoogste niveau selecteert, wordt alleen afgestemd op de sterkste zenders. Bij lagere niveaus wordt ook afgestemd op zwakkere zenders. TA (stand-by voor verkeersberichten) 1 Druk op M.C. om de functie Stand-by voor verkeersberichten in en uit te schakelen. AF (alternatieve frequenties zoeken) NEWS (onderbreking door nieuwsberichten) 1 Druk op M.C. om de nieuwsfunctie in of uit te schakelen. NEWS (nieuws), AFFAIRS (actualiteiten), INFO (informatie), SPORT (sport), WEATHER (weer), FINANCE (financieel nieuws) U kunt een functie toewijzen aan de linker en rechter toets van het toestel. Selecteer MAN (handmatig afstemmen) om handmatig af te stemmen of PCH (voorkeuzezenders) om op voorkeuzezenders af te stemmen. 1 Druk op M.C. om MAN of PCH te selecteren. POPULAR (populaire muziek) REGION (regionaal) POP MUS (populaire muziek), ROCK MUS (rockmuziek), EASY MUS (lichte muziek), OTH MUS (andere muziek), JAZZ (jazz), COUNTRY (countrymuziek), NAT MUS (nationale muziek), OLDIES (Gouwe Ouwe), FOLK MUS (folkmuziek) Als de functie AF is ingeschakeld, kan de regionale functie gebruikt worden om het zoeken tot regionale programma’s te beperken. 1 Druk op M.C. om de regionale functie in of uit te schakelen. CLASSICS (klassieke muziek) LOCAL (automatisch afstemmen op lokale zenders) L. CLASS (lichte klassieke muziek), CLASSIC (klassieke muziek) Een fragment selecteren 1 Druk op c of d. Vooruit of achteruit spoelen 1 Houd c of d ingedrukt. ! Als u gecomprimeerde audio afspeelt, is er geen geluid bij vooruit- en achteruitspoelen. Terugkeren naar de hoofdmap 1 Houd BAND ingedrukt. Overschakelen tussen gecomprimeerde audio en cd-da 1 Druk op BAND. Een ander display kiezen Cd/cd-r/cd-rw-discs Basisbediening Een cd/cd-r/cd-rw afspelen 1 Plaats een disc met het etiket omhoog in de laadsleuf. De gewenste informatie selecteren 1 Druk op DISP om over te schakelen tussen: CD-DA ! ELAPSED TIME (fragmentnummer en weergavetijd) ! CLOCK (naam signaalbron en klok) ! SPEANA (spectrumanalyzer) CD-TEXT ! TRACK INFO (fragmenttitel/naam artiest fragment/disctitel) ! ELAPSED TIME (fragmentnummer en weergavetijd) ! CLOCK (naam signaalbron en klok) ! SPEANA (spectrumanalyzer) MP3/WMA/WAV ! TRACK INFO (fragmenttitel/naam artiest/ albumtitel) ! FILE INFO (bestandsnaam/mapnaam) ! ELAPSED TIME (fragmentnummer en weergavetijd) ! CLOCK (naam signaalbron en klok) ! SPEANA (spectrumanalyzer) Nederlands SEEK (instelling linker/rechter toets) Met de functie BSM (Best Stations Memory) kunt u automatisch de zes sterkste zenders in het geheugen opslaan. Deze worden opgeslagen in volgorde van signaalsterkte. 1 Druk op M.C. om de functie BSM in te schakelen. Druk nogmaals op M.C. om deze te annuleren. NEWS/INFO (nieuws en informatie) Een map selecteren 1 Druk op 1/ of 2/ . 1 Druk op M.C. om AF aan of uit te zetten. BSM (geheugen voor de sterkste zenders) PTY-lijst 02 Een cd/cd-r/cd-rw uitwerpen 1 Druk op h. Nl <QRD3143-C> 73 73 Black plate (74,1) Hoofdstuk Bediening van het toestel 02 Opmerkingen ! De tekstinformatie onder TRACK INFO en FILE INFO wordt automatisch bijgewerkt. ! Afhankelijk van het mediabestandstype en de versie van iTunes waarmee MP3-bestanden op de disc zijn opgenomen, kan het voorkomen dat incompatibele tekst bij een audiobestand niet goed wordt weergegeven. ! Welke tekstinformatie gebruikt kan worden, hangt af van de informatiedrager. Bestanden en fragmenten in de lijst selecteren en afspelen 1 Druk op om over te schakelen naar de lijst met bestands- of fragmentnamen. 2 Gebruik M.C. om de gewenste bestandsnaam (of mapnaam) te selecteren. Een bestand of map selecteren 1 Draai aan M.C. Afspelen 1 Selecteer een bestand of fragment en druk op M.C. Bediening van het toestel Bediening met speciale toetsen Een herhaalbereik selecteren 1 Druk op 6/ om over te schakelen tussen: ! ALL – Alle fragmenten herhalen ! ONE – Het huidige fragment herhalen ! FLD – De huidige map herhalen Fragmenten in willekeurige volgorde afspelen om willekeurige weergave in of 1 Druk op 5/ uit te schakelen. Fragmenten in een geselecteerd herhaalbereik worden in willekeurige volgorde afgespeeld. ! Druk tijdens weergave in willekeurige volgorde op d om naar het volgende fragment te gaan. Als u op c drukt, wordt het huidige fragment opnieuw vanaf het begin afgespeeld. Het afspelen onderbreken 1 Druk op 4/PAUSE om het afspelen te onderbreken (pauze) of te hervatten. De geluidskwaliteit van gecomprimeerde audio verbeteren (sound retriever) 1 Druk op 3/S.Rtrv om over te schakelen tussen: 1—2—OFF (uit) 1 heeft effect bij lage compressie en 2 heeft effect bij hoge compressie. Een lijst van de bestanden (mappen) in de geselecteerde map weergeven 1 Selecteer een map en druk op M.C. Functie-instellingen Een song in de geselecteerde map afspelen 1 Selecteer een map en houd M.C. ingedrukt. 1 Druk op M.C. om het hoofdmenu weer te geven. 2 Draai aan M.C., selecteer de menuoptie FUNCTION en druk erop. U kunt de volgende functie aanpassen. S.RTRV (sound retriever) BALANCE (balansinstelling) Deze verbetert automatisch de weergave van gecomprimeerde audio en zorgt voor een vol geluid. 1 Druk op M.C. en selecteer de gewenste instelling. Raadpleeg De geluidskwaliteit van gecomprimeerde audio verbeteren (sound retriever) op deze bladzijde voor meer informatie. 1 Druk op M.C. om de instellingenmodus weer te geven. 2 Draai aan M.C. om de balans tussen de linker/ rechterluidsprekers in te stellen. Audio-instellingen 1 Druk op M.C. om het hoofdmenu weer te geven. 2 Draai aan M.C., selecteer de menuoptie AUDIO en druk erop. 3 Draai aan M.C. en selecteer de audiofunctie. U kunt de volgende audiofuncties aanpassen. ! FADER kan niet worden gebruikt als SUB.W/SUB.W is geselecteerd in SP-P/O MODE. Raadpleeg voor meer informatie SP-P/O MODE (achteruitgang en preout-instelling) op bladzijde 76. ! SUB.W, SUB.W CTRL en HPF SETTING kunnen niet worden gebruikt als REAR/REAR is geselecteerd in SP-P/O MODE. Raadpleeg voor meer informatie SP-P/O MODE (achteruitgang en preout-instelling) op bladzijde 76. ! SUB.W CTRL en HPF SETTING kunnen niet worden gebruikt als SUB.W is geselecteerd in OFF. Raadpleeg voor meer informatie SUB.W (subwoofer aan/uit) op de volgende bladzijde. EQ SETTING (equalizercurven) 1 Druk op M.C. om de instellingenmodus weer te geven. 2 Draai aan M.C. om de equalizer te selecteren. POWERFUL—NATURAL—VOCAL—CUSTOM1—CUSTOM2—FLAT—SUPER BASS De equalizerband en het equalizerniveau kunnen worden aangepast van CUSTOM1 en CUSTOM2. Volg de onderstaande procedure als u CUSTOM1 of CUSTOM2 selecteert. Voor een andere optie drukt u op M.C. om terug te keren naar het vorige display. ! CUSTOM1 kan voor elke signaalbron afzonderlijk ingesteld worden. ! CUSTOM2 is een gemeenschappelijk instelling voor alle signaalbronnen. 3 Druk op M.C. om de instellingenmodus weer te geven. 4 Druk op M.C. om over te schakelen tussen: Equalizerband—Equalizerniveau 5 Draai aan M.C. en selecteer de gewenste instelling. Equalizerband: 80HZ—250HZ—800HZ— 2.5KHZ—8KHZ Equalizerniveau: +6 tot –6 ! U kunt ook tussen de equalizers overschakelen te drukken. door op LOUDNESS (loudness) FADER (fader aanpassen) 1 Druk op M.C. om de instellingenmodus weer te geven. 2 Draai aan M.C. om de balans tussen de luidsprekers voorin en achterin in te stellen. 74 De loudness-functie compenseert een tekort aan lage tonen en hoge tonen bij een laag volume. 1 Druk op M.C. en selecteer de gewenste instelling. OFF (uit)—LOW (laag)—MID (midden)—HI (hoog) Nl <QRD3143-C> 74 Black plate (75,1) Hoofdstuk Bediening van het toestel SUB.W (subwoofer aan/uit) Dit toestel is voorzien van een in- en uitschakelbare subwooferuitgang. 1 Druk op M.C. en selecteer de gewenste instelling. NOR (normale fase)—REV (tegengestelde fase)—OFF (subwoofer uit) SUB.W CTRL (subwoofer aanpassen) De subwoofer geeft alleen frequenties beneden de geselecteerde waarde weer. 1 Druk op M.C. om de instellingenmodus weer te geven. 2 Druk op M.C. om over te schakelen tussen: Drempelfrequentie—Uitgangsniveau—Vervalniveau Instelbare waarden knipperen. 3 Draai aan M.C. en selecteer de gewenste instelling. Drempelfrequentie: 50HZ—63HZ—80HZ— 100HZ—125HZ—160HZ—200HZ Uitgangsniveau: –24 tot +6 Hellingsniveau: –6 — –12 BASS BOOST (bass boost) Als u wilt dat de luidsprekers voorin of achterin geen lage tonen (uit het frequentiebereik van de subwoofer) weergeven, kunt u het high pass filter (HPF) aanzetten. Alleen frequenties boven het geselecteerde bereik worden dan weergegeven door de voor- of achterluidsprekers. 1 Druk op M.C. om de instellingenmodus weer te geven. 2 Druk op M.C. om over te schakelen tussen: Drempelfrequentie—Vervalniveau 3 Draai aan M.C. en selecteer de gewenste instelling. Drempelfrequentie: OFF—50HZ—63HZ— 80HZ—100HZ—125HZ—160HZ—200HZ Hellingsniveau: –6 — –12 SLA (bronniveauregeling) Met de functie SLA (bronniveauregeling) kunt u het volumeniveau van elke signaalbron afzonderlijk instellen. Hierdoor kunt u plotselinge volumewisselingen voorkomen wanneer naar een andere signaalbron wordt overgeschakeld. ! De instellingen zijn gebaseerd op het FM-volumeniveau, dat zelf niet gewijzigd kan worden. ! Het MW/LW-volumeniveau kan ook met deze functie worden aangepast. ! Wanneer FM als signaalbron wordt gebruikt, kunt u niet overschakelen naar SLA. 1 Druk op M.C. om de instellingenmodus weer te geven. 2 Draai aan M.C. om het bronvolume te regelen. Instelbereik: +4 tot –4 Systeemmenu Belangrijk Als het toestel van de accu wordt losgekoppeld, wordt PW SAVE (energiezuinige modus) uitgeschakeld. Deze functie moet u weer inschakelen als het toestel terug met de accu wordt verbonden. Als het voertuig niet van een contactschakelaar met accessoirestand (ACC) is voorzien, is het (afhankelijk van de aansluiting) mogelijk dat het toestel de accu blijft belasten als PW SAVE (energiezuinige modus) is uitgeschakeld. 1 Druk op M.C. om het hoofdmenu weer te geven. 2 Draai aan M.C., selecteer de menuoptie SYSTEM en druk erop. 3 Draai aan M.C. en selecteer de systeemmenufunctie. U kunt de volgende functies in het systeemmenu aanpassen. LANGUAGE (taalinstelling) Dit toestel kan Engelse of Russische tekstinformatie bij een gecomprimeerd audiobestand weergeven. ! Als de gebruikte taal niet overeenkomt met de taalinstelling van dit toestel, wordt tekst wellicht niet correct weergegeven. ! Het is mogelijk dat sommige tekens niet juist worden weergegeven. 1 Draai aan M.C. en selecteer de gewenste instelling. ENG (Engels)—РУС (Russisch) HPF SETTING (high pass filter aanpassen) CLOCK SET (klok) 1 Druk op M.C. om de instellingenmodus weer te geven. 2 Druk op M.C. om het onderdeel van de klok te selecteren dat u wilt instellen. Uur—Minuut 3 Draai aan M.C. om de klok in te stellen. 02 1 Druk op M.C. en selecteer de gewenste instelling. 12H (12-uurs klok)—24H (24-uurs klok) AUTO PI (automatisch PI-zoeken) Als deze functie is ingeschakeld, probeert het toestel bij slechte ontvangst automatisch een andere zender met gelijkaardige programma’s te vinden, ook als u een voorkeuzezender selecteerde. 1 Druk op M.C. om de automatische PI-zoekfunctie in of uit te schakelen. AUX (externe aansluiting) Schakel deze instelling in als een extern apparaat op dit toestel is aangesloten. 1 Druk op M.C. om AUX in of uit te schakelen. MUTE MODE (dempen) Het geluid van dit toestel kan automatisch worden uitgeschakeld of gedempt wanneer een ander apparaat met uitschakelingsfunctie daarom vraagt met een speciaal signaal. 1 Druk op M.C. om de instellingenmodus weer te geven. 2 Draai aan M.C. en selecteer de gewenste instelling. U kunt een van de opties in de volgende lijst selecteren. ! MUTE – Tijdelijk uitschakelen ! 20dB ATT – Dempen (20dB ATT heeft meer effect dan 10dB ATT) ! 10dB ATT – Dempen PW SAVE (energiezuinige stand) Met deze functie wordt het energieverbruik van de accu verminderd. ! Als deze functie is ingeschakeld, kan alleen het bronsignaal worden ingeschakeld. 1 Druk op M.C. om de energiezuinige modus in of uit te schakelen. Nederlands 1 Druk op M.C. om de instellingenmodus weer te geven. 2 Draai aan M.C. en selecteer het gewenste niveau. U kunt het niveau verhogen of verlagen tussen de waarden 0 en +6. De waarde wordt op het display getoond. Bediening van het toestel 12H/24H (tijdweergave) Nl <QRD3143-C> 75 75 Black plate (76,1) Hoofdstuk Bediening van het toestel 02 De dimmer in- of uitschakelen U kunt de helderheid van de verlichting aanpassen. 1 Druk op M.C. om het hoofdmenu weer te geven. 2 Draai aan M.C., geef ILLUMI weer en druk erop. 3 Druk op M.C. en selecteer de gewenste instelling. OFF (uit)—ON (aan) ! U kunt de dimmer ook instellen door /DIMMER even ingedrukt te houden. Beginmenu 1 Houd SRC/OFF ingedrukt tot het toestel uit gaat. 2 Houd SRC/OFF ingedrukt tot het hoofdmenu wordt weergegeven. 3 Draai aan M.C., selecteer de menuoptie INITIAL en druk erop. 4 Draai aan M.C. en selecteer de gewenste functie. U kunt de volgende functies in het beginmenu aanpassen. Bediening van het toestel SP-P/O MODE (achteruitgang en preout-instelling) Op de uitgang voor de achterluidspreker en de RCA-uitgang van dit toestel kan een luidspreker met volledig bereik of een subwoofer aangesloten worden. Selecteer de gewenste instelling. 1 Druk op M.C. om de instellingenmodus weer te geven. 2 Draai aan M.C. en selecteer de gewenste instelling. U kunt een van de opties in de volgende lijst selecteren. ! REAR/SUB.W – Selecteer deze stand als op de uitgang voor de achterluidspreker een luidspreker met volledig bereik aangesloten is, en op de RCA-uitgang een subwoofer aangesloten is. ! SUB.W/SUB.W – Selecteer deze stand als op de uitgang voor de achterluidspreker een subwoofer rechtstreeks aangesloten is zonder versterker, en op de RCA-uitgang een subwoofer is aangesloten. ! REAR/REAR – Selecteer deze stand als op de uitgang voor de achterluidspreker en op de RCA-uitgang een luidspreker met volledig bereik is aangesloten. Als op de uitgang voor de achterluidspreker een luidspreker met volledig bereik is aangesloten en de RCA-uitgang niet gebruikt wordt, kunt u zowel REAR/SUB.W als REAR/REAR selecteren. 76 De AUX-signaalbron 1 Steek de stereo-miniplugkabel in de AUX-ingang van dit toestel. 2 Druk op SRC/OFF en kies AUX als signaalbron. Opmerking De signaalbron AUX kan alleen worden geselecteerd als de externe aansluiting is ingeschakeld. Raadpleeg voor meer informatie AUX (externe aansluiting) op de vorige bladzijde. Een ander display kiezen De gewenste informatie selecteren 1 Druk op DISP om over te schakelen tussen: ! Naam signaalbron ! Naam signaalbron en klok Als een scherm verkeerd wordt weergegeven Zet het ongewenste scherm als volgt uit. FM STEP (FM-afstemstap) Standaard wordt er bij automatisch afstemmen een FM-afstemstap van 50 kHz gebruikt, en 100 kHz als de functie AF of TA is ingeschakeld. Maar soms krijgt u een beter resultaat als ook bij het afstemmen op alternatieve frequenties (AF) een afstemstap van 50 kHz wordt gebruikt. ! Bij handmatig afstemmen blijft de afstemstap 50 kHz. 1 Druk op M.C. om de FM-afstemstap te selecteren. 50 (50 kHz)—100 (100 kHz) 4 Draai aan M.C. en selecteer de systeemmenufunctie. U kunt de volgende functies in het systeemmenu aanpassen. Raadpleeg Systeemmenu op de vorige bladzijde voor meer informatie. Systeemmenu 1 Houd SRC/OFF ingedrukt tot het toestel uit gaat. 2 Houd SRC/OFF ingedrukt tot het hoofdmenu wordt weergegeven. 3 Draai aan M.C., selecteer de menuoptie SYSTEM en druk erop. 1 Druk op M.C. om het hoofdmenu weer te geven. 2 Draai aan M.C., selecteer de menuoptie SYSTEM en druk erop. 3 Draai aan M.C., geef DEMO OFF weer en druk erop. 4 Draai aan M.C. en selecteer YES. 5 Druk op M.C. om uw keuze te bevestigen. Nl <QRD3143-C> 76 Black plate (77,1) Hoofdstuk Installatie Installatie — Verwijder nooit de isolatie van de voedingskabel van dit toestel om andere apparaten van stroom te voorzien. De stroomcapaciteit van de voedingskabel is beperkt. — Gebruik een zekering met het voorgeschreven vermogen. — Verbind de negatieve luidsprekerkabel nooit rechtstreeks met de aarding. — Voeg de negatieve kabels van verschillende luidsprekers nooit samen. Verbindingen F O N OF Belangrijk ! Als dit toestel wordt geïnstalleerd in een voertuig met een contactschakelaar zonder ACCstand (accessoirestand), kan de accu leeglopen als de rode kabel niet wordt aangesloten op de aansluiting die de bediening van de contactschakelaar herkent. STAR T ACC-stand Geen ACC-stand ! Gebruik van dit toestel onder andere omstandigheden dan de volgende kan leiden tot brand of storingen. — Voertuigen met een accu van 12 volt en negatieve aarding. — Luidsprekers van 50 W (uitgangswaarde) en 4 W tot 8 W (impedantiewaarde). ! Om kortsluiting, oververhitting en storingen te voorkomen, moet u onderstaande aanwijzingen opvolgen. Dit toestel 1 3 1 2 3 4 5 4 2 5 Ingang stroomkabel Achteruitgang of subwooferuitgang Antenne-ingang Zekering (10 A) Ingang voor draadafstandsbediening Een bedrade afstandsbedieningsadapter kan aangesloten worden (los verkrijgbaar). Stroomkabel 2 7 3 4 5 6 3 4 5 6 1 8 a 9 e b c d 1 Naar ingang stroomkabel 2 De functie van 3 en 5 kan verschillen afhankelijk van het type voertuig. Verbind in dat geval 4 met 5 en 6 met 3. 3 Geel Back-up (of accessoire) 4 Geel Aansluiten op de constante 12 V-voedingsaansluiting. 5 Rood Accessoire (of back-up) 6 Rood Aansluiten op een aansluiting die door de contactschakelaar wordt aangestuurd (12 V gelijkstroom). 7 Verbind kabels van dezelfde kleur met elkaar. 8 Zwart (chassisaarding) 9 Blauw-wit De pinpositie van de ISO-connector verschilt naargelang het type voertuig. Als pin 5 de antenne aanstuurt, verbindt u 9 en b. In andere typen voertuigen verbindt u 9 en b nooit. a Blauw-wit Aansluiten op systeembedieningsaansluiting van de versterker (maximaal 300 mA, 12 V gelijkstroom). b Blauw-wit Aansluiten op bedieningsaansluiting van de gemotoriseerde antenne (maximaal 300 mA, 12 V gelijkstroom). c Geel/zwart Als u apparatuur met dempingsfunctie gebruikt, verbindt u deze draad met de draad voor audiodemping op die apparatuur. Als u zulke apparatuur niet gebruikt, verbindt u de draad voor audiodemping niet. d Luidsprekerkabels Wit: Linksvoor + Wit-zwart: Linksvoor * Grijs: Rechtsvoor + Grijs-zwart: Rechtsvoor * Groen: Linksachter + of subwoofer + Groen-zwart: Linksachter * of subwoofer * Violet: Rechtsachter + of subwoofer + Violet-zwart: Rechtsachter * of subwoofer * e ISO-connector Bij sommige voertuigen is de ISO-connector in twee verdeeld. Verbind in dat geval beide connectoren. Opmerkingen ! Wijzig het beginmenu van het toestel. Raadpleeg gedeelte SP-P/O MODE (achteruitgang en preout-instelling) op de vorige bladzijde. De subwooferuitgang van dit toestel is mono. ! Als u een subwoofer van 70 W (2 W) gebruikt, moet u de subwoofer aansluiten op de violette en zwart-violette draden van dit toestel. Sluit niets aan op de groene en groen-zwarte draden. Nl <QRD3143-C> 77 Nederlands — Koppel de negatieve aansluiting van de accu los voordat u het toestel installeert. — Gebruik kabelklemmen of plakband om de bekabeling veilig aan te brengen. Bescherm de kabels met plakband op plaatsen waar deze tegen metalen onderdelen liggen. — Plaats geen kabels in de buurt van beweegbare onderdelen zoals de versnellingspook of de stoelrails. — Leg kabels niet op plaatsen die heet kunnen worden, zoals dicht bij de kachel. — Sluit de gele kabel niet op de accu aan via een gat in het motorcompartiment. — Dek alle ongebruikte kabelaansluitingen af met isolatietape. — Maak de kabels niet korter. ! Als dit apparaat aan staat, wordt het bedieningssignaal doorgegeven via de blauw/witte kabel. Verbind deze kabel met de afstandsbediening van een externe versterker of met de bedieningsaansluiting van de automatische antenne van het voertuig (maximaal 300 mA, 12 V gelijkstroom). Als het voertuig is uitgerust met een glasantenne, verbindt u deze met de voedingsaansluiting van de antennebooster. ! Verbind de blauw/witte kabel nooit met de voedingsaansluiting van een externe versterker of automatische antenne. Anders kan de accu leeglopen of kan er storing optreden. ! De zwarte kabel is de aarding. Dit toestel moet gescheiden worden geaard van andere apparaten (met name apparaten die veel stroom verbruiken zoals een versterker). Anders kan er brand of storing ontstaan wanneer de aarding per ongeluk losraakt. 03 77 Black plate (78,1) Hoofdstuk Installatie 03 Installatie Versterker (apart verkrijgbaar) Maak deze verbindingen als de optionele versterker wordt gebruikt. 2     Het toestel verwijderen 1 Verwijder de sierlijst. 1 4 5 1 Systeemafstandsbediening Verbinden met blauw-witte kabel. 2 Versterker (apart verkrijgbaar) 3 Aansluiten op RCA-kabels (apart verkrijgbaar) 4 Naar achteruitgang of subwooferuitgang 5 Luidspreker achterin of subwoofer Installatie Belangrijk ! Controleer alle aansluitingen en systemen voordat u de installatie voltooit. ! Gebruik geen onderdelen van andere fabrikanten; deze kunnen storingen veroorzaken. ! Neem contact op met uw dealer als er voor de installatie gaten moeten worden geboord of als er andere aanpassingen aan het voertuig nodig zijn. ! Installeer dit toestel niet op een plaats waar: — het de besturing van het voertuig kan belemmeren. — het de inzittenden kan verwonden bij een noodstop. ! De halfgeleiderlaser raakt bij oververhitting beschadigd. Plaats dit apparaat niet op plaatsen waar het warm wordt, zoals nabij de uitlaat van een kachel. 78 2 Zet de montagebehuizing vast door met een schroevendraaier de metalen lipjes op hun plaats te buigen (90°). 60° 3 1 5 ! Dit toestel werkt het beste als het wordt geplaatst onder een hoek van minder dan 60°. ! Laat bij het plaatsen voldoende ruimte vrij achter het achterpaneel en wikkel losse kabels zo dat ze de ventilatiegaten niet blokkeren; zorg altijd dat warmte goed wordt afgevoerd tijdens gebruik van het toestel. Laat voldoende 5 cm ruimte vrij 5 cm 5cm cm 2 1 Sierlijst 2 Lipje met inkeping ! De sierlijst is gemakkelijker bereikbaar als u het voorpaneel verwijdert. ! Plaats de sierlijst terug met de kant met het lipje met de inkeping onderaan. 1 Dashboard 2 Montagebehuizing # Controleer of het toestel stevig op zijn plaats is gemonteerd. Het toestel functioneert wellicht niet naar behoren als het niet goed is bevestigd. DIN-achtermontage 1 Bepaal de juiste positie waar de gaten in de klem en in de zijde van het toestel op een lijn liggen. 2 Steek de meegeleverde uittreksleutels in de beide kanten van het toestel totdat ze op hun plaats klikken. 3 Trek het toestel uit het dashboard. DIN-bevestiging voor/achter Dit toestel kan geïnstalleerd worden via een voor- of achtermontage. Gebruik voor installatie in de handel verkrijgbare onderdelen. 2 Draai aan elke kant twee schroeven vast. DIN-voormontage 1 Schuif de montagebehuizing in het dashboard. Gebruik voor installatie in een ondiepe ruimte de meegeleverde montagebehuizing. Als er voldoende ruimte is, gebruikt u de montagebehuizing die met het voertuig geleverd werd. 3 1 2 1 Zelftappende schroef (5 mm × 8 mm) 2 Bevestigingsklem 3 Dashboard of console Het voorpaneel verwijderen en terug bevestigen U kunt het voorpaneel verwijderen om het toestel tegen diefstal te beveiligen. Druk op de knop om het voorpaneel los te maken, duw het naar boven en trek het naar u toe. Raadpleeg Het voorpaneel tegen diefstal verwijderen en Het voorpaneel terugzetten op bladzijde 72 voor meer informatie. Nl <QRD3143-C> 78 Black plate (79,1) Aanhangsel Aanvullende informatie Problemen verhelpen Symptoom Oorzaak Actie Het display keert automatisch terug naar het gewone display. U hebt gedurende ongeveer 30 seconden geen handeling uitgevoerd. Voer de handeling opnieuw uit. Het bereik voor herhaald afspelen wordt onverwachts gewijzigd. Afhankelijk van Selecteer het gehet herhaalbewenste herhaalreik kan het ge- bereik opnieuw. selecteerde bereik gewijzigd worden wanneer u een andere map of een ander fragment selecteert of vooruit of achteruit spoelt. Een onderliggende map wordt niet afgespeeld. Onderliggende Selecteer een mappen worden ander herhaalbeniet afgespeeld reik. wanneer FLD (map herhalen) is geselecteerd. Wijzig de displaystand of speel een ander fragment of bestand af. Symptoom Het toestel functioneert niet correct. Er is interferentie. Oorzaak Er wordt nabij dit toestel een ander apparaat (bijvoorbeeld een draagbare telefoon) gebruikt dat elektromagnetische straling uitzendt. Actie Gebruik nabij dit toestel geen elektrische apparaten die interferentie kunnen veroorzaken. Aanwijzingen voor het gebruik Cd-speler Melding Oorzaak Actie Discs en de player ERROR-07, De disc is vuil. 11, 12, 17, 30 De disc is bekrast. Reinig de disc. ERROR-07, 10, 11, 12, 15, 17, 30, A0 Elektrisch of mechanisch probleem. Zet het contact uit en weer aan, of schakel over naar een andere signaalbron en dan terug naar de cd-speler. Foutmeldingen ERROR-15 Schrijf een foutmelding altijd nauwkeurig op en houd die bij de hand als u contact opneemt met uw leverancier of Pioneer-servicecentrum. De geplaatste disc bevat geen gegevens. Plaats een andere disc. Gebruik discs van 12 cm. Gebruik geen discs van 8 cm en probeer deze ook niet met een adapter af te spelen. ERROR-23 Het cd-formaat wordt niet ondersteund. Plaats een andere disc. Gebruik uitsluitend normale, ronde discs. Gebruik geen discs met een andere vorm. FORMAT READ Na het begin Wacht tot het bevan het afspelen richt verdwijnt en duurt het soms er geluid klinkt. even totdat er geluid klinkt. Algemeen Melding Oorzaak Actie AMP ERROR Het toestel werkt niet of er is een probleem met de luidsprekeraansluiting; het beveiligingscircuit is geactiveerd. Controleer de luidsprekeraansluiting. Neem contact op met uw leverancier of een erkend Pioneer Servicecentrum als het bericht nog wordt weergegeven nadat u de motor hebt uit- en aangezet. Plaats een andere disc. NO AUDIO De geplaatste disc bevat geen afspeelbare bestanden. SKIPPED Plaats een andere De geplaatste disc. disc bevat bestanden die door digitaal rechtenbeheer (DRM) beveiligd zijn. PROTECT Alle bestanden op de disc zijn door digitaal rechtenbeheer (DRM) beveiligd. Plaats een andere disc. Plaats een andere disc. Gebruik uitsluitend discs die voorzien zijn van een van onderstaande twee logo’s. Plaats geen ander object dan een cd in de cd-laadsleuf. Gebruik geen gebarsten, gebroken, kromme of op andere wijze beschadigde discs omdat die de speler kunnen beschadigen. Niet-gefinaliseerde cd-r/rw-discs kunnen niet worden afgespeeld. Raak de gegevenszijde van de disc niet aan. Bewaar discs in het bijbehorende doosje wanneer u ze niet gebruikt. Plak geen labels op discs, schrijf er niet op en breng het oppervlak niet in aanraking met chemische middelen. Nederlands Als het disEr is geen tekstplay wordt ge- informatie bewijzigd, verschikbaar. schijnt NO XXXX (bijvoorbeeld NO TITLE). Aanvullende informatie Als u een cd reinigt, veegt u de disc van het midden naar de buitenkant met een zachte doek schoon. Nl <QRD3143-C> 79 79 Black plate (80,1) Aanhangsel Aanvullende informatie Condens en vocht kunnen de werking van de speler tijdelijk negatief beïnvloeden. Laat de speler in een warmere omgeving ongeveer een uur op temperatuur komen. Veeg vochtige schijven met een zachte doek schoon. Sommige discs kunnen niet worden afgespeeld afhankelijk van het type disc, de indeling ervan, de toepassing waarmee deze is opgenomen, de omgeving waarin deze wordt afgespeeld, de manier waarop deze wordt bewaard, enzovoort. Aanvullende informatie Het regelmatig plaatsen en uitwerpen van een DualDisc kan krassen veroorzaken op de disc wat tot afspeelproblemen leidt. In sommige gevallen kan een DualDisc vast komen te zitten in de cdlaadsleuf en niet meer worden uitgeworpen. Om problemen te voorkomen wordt aangeraden om op dit toestel geen DualDiscs af te spelen. Raadpleeg de informatie van de fabrikant van de disc voor meer informatie over DualDiscs. Bestandsextensie: .wav Quantisatiebits: 8 en 16 (LPCM), 4 (MS ADPCM) Bemonsteringsfrequentie: 16 kHz tot 48 kHz (LPCM), 22,05 kHz en 44,1 kHz (MS ADPCM) Bijkomende informatie Schokken tijdens het rijden van het voertuig kunnen de disc laten overslaan. Compatibiliteit met gecomprimeerde audio Alleen de eerste 32 tekens van de bestandsnaam (inclusief de extensie) of mapnaam worden weergegeven. Lees de voor discs geldende voorzorgsmaatregelen voordat u ze gebruikt. WMA Russische tekst kan alleen op dit toestel worden weergegeven als die met een van de volgende tekensets is gecodeerd: ! Unicode (UTF-8, UTF-16) ! Andere tekensets dan Unicode die in een Windows-omgeving worden gebruikt en op Russisch zijn ingesteld bij de taalinstellingen Bij gebruik van discs met een bedrukbaar labeloppervlak moet u de instructies en waarschuwingen van de discs controleren. Afhankelijk van de disc kan laden of uitwerpen niet mogelijk zijn. Het gebruik van zulke discs kan dit toestel beschadigen. Plak geen in de handel verkrijgbare labels of andere materialen op de discs. ! De discs kunnen vervormen waardoor ze onafspeelbaar kunnen worden. ! De labels kunnen loslaten tijdens het afspelen en de disc blokkeren bij het uitwerpen en het toestel beschadigen. Bestandsextensie: .wma Bitsnelheid: 48 kbps tot 320 kbps (CBR), 48 kbps tot 384 kbps (VBR) Bemonsteringsfrequentie: 32 kHz, 44,1 kHz, 48 kHz Windows Media Audio Professional, Lossless, Voice/DRM Stream/Stream met video: Niet compatibel Disc DualDiscs zijn dubbelzijdige discs met aan de ene kant een beschrijfbaar cd-oppervlak voor audio-opnamen en aan de andere kant een beschrijfbaar dvd-oppervlak voor video-opnamen. Aangezien de cd-zijde van DualDiscs niet overeenkomt met de algemene cd-standaard, is het wellicht niet mogelijk de cd-zijde op dit toestel af te spelen. Bitsnelheid: 8 kbps tot 320 kbps (CBR), VBR Bemonsteringsfrequentie: 8 kHz tot 48 kHz (32 kHz, 44,1 kHz, 48 kHz voor de beste kwaliteit) Mappenhiërarchie: maximaal acht niveaus diep (Voor praktisch gebruik kunt u beter niet meer dan twee niveaus gebruiken.) Afspeelbare mappen: maximaal 99 Bij het afspelen van gecomprimeerde audiodiscs wordt altijd een korte pauze ingelast tussen de fragmenten. Dit gebeurt ongeacht de duur tussen de fragmenten op de originele opname. LET OP Laat discs niet achter op plaatsen waar de temperatuur hoog kan oplopen. Volgorde van audiobestanden De gebruiker kan met dit toestel geen mapnummers toewijzen of de afspeelvolgorde wijzigen. Voorbeeld van een boomstructuur 01 02 1 2 03 3 4 04 5 6 05 Niveau 1 Niveau 2 Niveau 3 Niveau 4 : Map : Gecomprimeerd audiobestand 01 tot 05: Mapnummer 1 tot 6: Afspeelvolgorde Disc De mapvolgorde en andere instellingen zijn afhankelijk van de software die voor het coderen en schrijven is gebruikt. Afspeelbare bestanden: maximaal 999 Compatibele ID3-tag-versie: 1.0, 1.1, 2.2, 2.3, 2.4 (ID3-tag versie 2.x krijgt prioriteit boven versie 1.x.) Bestandssysteem: ISO 9660 Level 1 en 2, Romeo, Joliet M3u speellijst: Niet compatibel Afspelen van multisessie-discs: Compatibel MP3i (MP3 interactive), mp3 PRO: Niet compatibel Packet write data transfer: Niet compatibel Een juiste werking van dit toestel is afhankelijk van de toepassing waarmee de WMA-bestanden zijn gecodeerd. MP3 Bestandsextensie: .mp3 DualDiscs 80 WAV Lijst van Russische tekens S: T S: T S: T S: T S: T :А :Б :В :Г :Д : Е, Ё :Ж :З : И, Й :К :Л :М :Н :О :П Nl <QRD3143-C> 80 Black plate (81,1) Aanhangsel Aanvullende informatie S: T S: T S: T S: T S: T :Р :С :Т :У :Ф :Х :Ц :Ч : Ш, Щ :Ъ :Ы :Ь :Э :Ю :Я S: Scherm T: Teken Copyright en handelsmerken iTunes Apple en iTunes zijn handelsmerken van Apple Inc., geregistreerd in de V.S. en andere landen. Aanvullende informatie Technische gegevens Algemeen Spanningsbron ................ 14,4 V gelijkstroom (10,8 tot 15,1 V toelaatbaar) Aarding ........................... Negatief Maximaal stroomverbruik ................................... 10,0 A Afmetingen (B × H × D): DIN Chassis .............. 178 mm × 50 mm × 165 mm Voorkant ............ 188 mm × 58 mm × 16 mm D Chassis .............. 178 mm × 50 mm × 165 mm Voorkant ............ 170 mm × 46 mm × 16 mm Gewicht ........................... 1 kg MP3 Dit product is uitsluitend bedoeld voor niet-commercieel privégebruik. Het mag niet in een commerciële omgeving worden gebruikt voor realtime-uitzendingen (over land, via satelliet, kabel en/of andere media), voor uitzendingen/ streaming via internet, intranet en/of andere netwerken, of in andere elektronische distributiesystemen zoals betaalradio of audio-opaanvraagtoepassingen. Hiervoor is een aparte licentie nodig. Kijk voor meer informatie op http://www.mp3licensing.com. WMA Systeem ........................... Bruikbare discs ................ Signaal-tot-ruisverhouding ................................... Aantal kanalen ................. MP3-decoderingsformaat ................................... WMA-decoderingsformaat ................................... Compact Disc Audio Compact Discs 94 dB (1 kHz) (IEC-A-netwerk) 2 (stereo) MPEG-1 & 2 Audio Layer 3 Versie 7, 7.1, 8, 9, 10, 11, 12 (2 kan. audio) (Windows Media Player) WAV-signaalformaat ........ Lineaire PCM & MS ADPCM (niet gecomprimeerd) FM-tuner Frequentiebereik .............. 87,5 MHz tot 108,0 MHz Bruikbare gevoeligheid .... 9 dBf (0,8 µV/75 W, mono, S/R: 30 dB) Signaal-tot-ruisverhouding ................................... 72 dB (IEC-A-netwerk) Audio Maximaal uitgangsvermogen ................................... 50 W × 4 70 W × 1/2 W (voor de subwoofer) Doorlopend uitgangsvermogen ................................... 22 W × 4 (50 Hz tot 15 000 Hz, 5% THD, 4 W belasting, beide kanalen) Belastingsimpedantie ...... 4 W (4 W tot 8 W toegestaan) Preout maximaal uitgangsniveau ................................... 2,0 V Contouren loudness ......... +10 dB (100 Hz), +6,5 dB (10 kHz) (volume: –30 dB) Equalizer (grafische equalizer met vijf banden): Frequentie ................ 80 Hz/250 Hz/800 Hz/ 2,5 kHz/8 kHz Bereik equalizer ........ ±12 dB (in stappen van 2 dB) Subwoofer (mono): Frequentie ................ 50 Hz/63 Hz/80 Hz/100 Hz/ 125 Hz/160 Hz/200 Hz Helling ...................... –6 dB/oct, –12 dB/oct Gain ......................... +6 dB tot –24 dB Fase .......................... Normaal/tegengesteld MW-tuner Frequentiebereik .............. 531 kHz tot 1 602 kHz Bruikbare gevoeligheid .... 25 µV (S/R: 20 dB) Signaal-tot-ruisverhouding ................................... 62 dB (IEC-A-netwerk) LW-tuner Frequentiebereik .............. 153 kHz tot 281 kHz Bruikbare gevoeligheid .... 28 µV (S/R: 20 dB) Signaal-tot-ruisverhouding ................................... 62 dB (IEC-A-netwerk) Opmerking Technische gegevens en ontwerp kunnen zonder voorafgaande kennisgeving worden gewijzigd. Nederlands Windows Media is een gedeponeerd handelsmerk of een handelsmerk van Microsoft Corporation in de Verenigde Staten en/of in andere landen. Dit product bevat technologie die het eigendom is van Microsoft Corporation en die niet gebruikt of gedistribueerd mag worden zonder toestemming van Microsoft Licensing, Inc. Cd-speler Nl <QRD3143-C> 81 81 Black plate (82,1) Раздел Перед началом эксплуатации 01 Благодарим Вас за покупку этого изделия компании PIONEER. Для обеспечения правильности эксплуатации внимательно прочитайте данное руководство перед началом использования изделия. Особенно важно, чтобы Вы прочли и соблюдали инструкции, помеченные в данном руководстве заголовками ПРЕДУПРЕЖДЕНИЕ и ВНИМАНИЕ. Держите данное руководство под рукой для обращения к нему в будущем. Перед началом эксплуатации шего изделия с соблюдением обязательных процедур по обработке, утилизации и вторичной переработке и, таким образом, предотвратите потенциальное негативное воздействие на окружающую среду и здоровье людей. Дату изготовления оборудования можно определить по серийному номеру, который содержит информацию о месяце и годе производства. Если вы желаете утилизировать данное изделие, не выбрасывайте его вместе с обычным бытовым мусором. Существует отдельная система сбора использованных электронных изделий в соответствии с законодательством, которая предполагает соответствующее обращение, возврат и переработку. Частные лица в странах Евросоюза, Швейцарии и Норвегии могут бесплатно возвращать использованные электронные изделия в специализированные пункты приема или в магазин (при покупке аналогичного нового устройства). Если Ваша страна не указана в приведенном выше перечне, обращайтесь в органы местного управления за инструкциями по правильной утилизации продукта. Тем самым Вы обеспечите утилизацию Ва- 82 Сведения об этом устройстве Частоты тюнера в этом устройстве распределены для использования в Западной Европе, Азии, на Ближнем Востоке, в Африке и Океании. При использовании в других регионах качество приема может быть плохим. Функция RDS (радиовещательная система передачи информации) доступна только в регионах, где транслируются сигналы RDS для FM-станций. ВНИМАНИЕ Данное изделие является лазерным изделием класса 1 согласно классификации по Безопасности лазерных изделий, IEC 60825-1:2007. ВНИМАНИЕ ! Не допускайте попадания жидкости на устройство. Это может повлечь поражение электрическим током. Кроме того, попадание жидкости в устройство может стать причиной его выхода из строя, перегрева и появления дыма. ! Pioneer CarStereo-Pass предназначен для использования только в Германии. ! Всегда сохраняйте уровень громкости достаточно низким, чтобы были слышны звуки извне. ! Не допускайте воздействия влажности на изделие. ! При отключении или разряде аккумуляторной батареи память предварительных настроек будет стерта. Примечание Выполненные настройки вступают в силу, даже если выйти из меню без подтверждения настройки. В случае возникновения неполадок При неполадках в работе этого изделия свяжитесь с торговым представителем компании-производителя или с ближайшим сервисным пунктом Pioneer. ЛАЗЕРНЫЙ ПРОДУКТ КЛАСС 1 Ru <QRD3143-C> 82 Black plate (83,1) Раздел Управление данным устройством Основное устройство Индикатор 1 2 34 5 6 7 8 9 a b Элемент 1 8 SRC/OFF 9 (назад)/DIMMER (регулятор освещенности) 3 MULTI-CONTROL (M.C.) a c/d 4 (список) b С 1/ по 6/ 5 DISP c 6 Щель для загрузки диска d Кнопка снятия панели (эквалайзер) Индикация на дисплее 1 Отображается дополнительная информация. 3 TA (дорожные сводки) Включена функция приема дорожных сводок. 4 TP (идентификатор дорожных программ) Тюнер настроен на TPстанцию. 5 Вход AUX (стереоразъем 3,5 мм) 7 2 BAND 2 3 5 6 8 7 a Состояние Сектор основной информации ! Тюнер: диапазон и частота ! RDS: название программы, PTY-информация и прочая текстовая информация ! Проигрыватель компактдисков: время, прошедшее с начала воспроизведения, и текстовая информация 9 a Включен режим Sound Retriever (технология преобразования звука). 6 LOC Включена настройка с местным поиском. 7 (повтор) Включён режим повторного воспроизведения дорожки или папки. 8 (в проВключён режим воспроизизвольной ведения в произвольной попоследоваследовательности. тельности) Отображается при наличии нижнего уровня папки или меню. Установочное меню При повороте ключа зажигания в положение ON после установки устройства на дисплее появляется установочное меню. Оно позволяет выполнить следующие настройки. 1 После установки устройства поверните ключ зажигания в положение ON. Появится надпись SET UP. 2 Поверните M.C. для выбора YES. # Если в течение 30 секунд не выполняется никаких операций, установочное меню не будет выводиться. # Если вы хотите выполнить настройку позже, поверните M.C., чтобы выбрать NO. Нажмите для выбора. В случае выбора NO настройка в установочном меню невозможна. 3 Нажмите M.C. для выбора. 02 4 Для настройки выполните следующие процедуры. Для перехода к следующему пункту меню необходимо подтвердить выбор. LANGUAGE (выбор языка) Данное устройство может отображать текстовую информацию из сжатых аудиофайлов, в том числе информацию на английском и русском языках. ! При несовместимости настроек встроенного и выбранного языка возможны искажения при выводе текстовых сообщений. ! Некоторые символы могут отображаться неправильно. 1 Поворачивайте M.C. для выбора настройки. ENG (английский)—РУС (русский) 2 Нажмите M.C., чтобы подтвердить выбор. CLOCK SET (установка часов) 1 Поворачивайте M.C., чтобы установить часы. 2 Нажимайте M.C., чтобы выбрать установку минут. 3 Поворачивайте M.C., чтобы установить минуты. 4 Нажмите M.C., чтобы подтвердить выбор. FM STEP (шаг настройки в FM-диапазоне) Обычно шаг настройки в FM-диапазоне, используемый при настройке с поиском, составляет 50 кГц. При включении функции AF или TA шаг настройки автоматически меняется на 100 кГц. При включенной функции AF предпочтительно установить шаг настройки 50 кГц. ! Во время ручной настройки шаг настройки составляет 50 кГц. 1 Поверните M.C., чтобы выбрать шаг настройки в FM-диапазоне. 50 (50 кГц)—100 (100 кГц) 2 Нажмите M.C., чтобы подтвердить выбор. Появится надпись QUIT. Ru <QRD3143-C> 83 Русский 9 4 (sound retriever, технология преобразования звука) Индикатор Работает функция списка. (список) Сектор дополнительной информации c d 2 Состояние 1 Элемент h (извлечение) Управление данным устройством 83 Black plate (84,1) Раздел Управление данным устройством 02 5 Чтобы закончить настройку, поверните M.C. и выберите YES. # Если понадобится вновь изменить настройку, поверните M.C. и выберите NO. Нажмите для выбора. 6 Нажмите M.C. для выбора. Примечания ! Настроить параметры меню можно в меню системы. Более подробную информацию см. в разделе Меню системы на стр. 88. ! Вы можете отменить настройку параметра, нажав кнопку SRC/OFF. Основные операции ! ! ! ! Важно Соблюдайте осторожность при снятии и установке передней панели. Оберегайте переднюю панель от сильных ударов. Предохраняйте переднюю панель от воздействия прямого солнечного света и высоких температур. Прежде чем снять переднюю панель, обязательно отключите от нее все кабели и устройства, чтобы не повредить устройство и внутреннюю отделку салона. Снятие передней панели в целях защиты от кражи 1 Чтобы отсоединить переднюю панель, нажмите на кнопку отсоединения панели. 2 Нажмите на панель по направлению вверх (M) и потяните на себя (N). Выбор источника сигнала 1 Нажимайте кнопку SRC/OFF для выбора из следующих функций: TUNER (тюнер)—CD (проигрыватель компакт-дисков)—AUX (вспомогательное устройство (AUX)) Регулировка громкости 1 Для регулировки громкости поворачивайте M.C. 3 Всегда храните снятую переднюю панель в защитном футляре. Установка передней панели 1 Зафиксируйте левый край панели на устройстве. Убедитесь, что язычки с левой стороны основного устройства вошли в пазы на передней панели. ВНИМАНИЕ В целях безопасности остановите автомобиль, прежде чем снять переднюю панель. Примечание Когда голубой/белый провод этого устройства подключен к реле панели управления автомобильной антенной, антенна на автомобиле выдвигается при включении источника сигнала этого устройства. Чтобы втянуть антенну, выключите источник сигнала. Часто используемые элементы меню 2 Нажмите на правый край передней панели и зафиксируйте ее. Если прикрепить переднюю панель к основному устройству не удается, убедитесь, что действия производятся в правильном порядке. В случае приложения излишнего усилия передняя панель или основное устройство могут быть повреждены. Включение устройства 1 Нажмите кнопку SRC/OFF, чтобы включить устройство. Выключение устройства 1 Нажмите и удерживайте кнопку SRC/OFF, пока устройство не выключится. 84 Управление данным устройством Возврат к предыдущему дисплею Возврат к предыдущему списку (к папке на один уровень выше) /DIMMER. 1 Нажмите кнопку Возврат в исходный режим Выход из главного меню 1 Нажмите BAND. Возврат в исходный режим из списка 1 Нажмите BAND. Тюнер Основные операции Выбор диапазона 1 Нажимайте кнопку BAND, пока на дисплее не появится нужный диапазон (FM1, FM2, FM3 для FM или MW/LW). Переключение станций предварительной настройки 1 Нажмите кнопку c или d. ! Выберите PCH (станции предварительной настройки) в меню SEEK, чтобы воспользоваться этой функцией. Подробнее о настройках см. в разделе SEEK (настройка левой и правой кнопок) на стр. 86. Ручная настройка (пошаговая) 1 Нажмите кнопку c или d. ! Выберите MAN (ручная настройка) в меню SEEK, чтобы воспользоваться этой функцией. Подробнее о настройках см. в разделе SEEK (настройка левой и правой кнопок) на стр. 86. Поиск 1 Нажмите и удерживайте кнопку c или d, а затем отпустите. Вы можете отменить настройку с поиском кратким нажатием c или d. При нажатии и удерживании кнопки c или d можно пропускать радиостанции. Настройка с поиском начнется сразу после отпускания кнопки c или d. Примечание Можно включить или выключить функцию AF (поиск альтернативных частот) данного устройства. Для обычной настройки функция AF должна быть выключена (смотрите в AF (поиск альтернативных частот) на стр. 85). Ru <QRD3143-C> 84 Black plate (85,1) Раздел Управление данным устройством Сохранение и вызов из памяти радиостанций для каждого диапазона Использование кнопок предварительной настройки 1 Чтобы сохранить в памяти нужную радиостанцию, нажмите одну из кнопок предварительной настройки (с 1/ по 6/ ) и удерживайте ее, пока номер предварительной настройки не прекратит мигать. 2 Для выбора нужной радиостанции нажмите одну из кнопок предварительной настройки (с 1/ по 6/ ). Переключение дисплея Выбор текстовой информации 1 Нажимайте DISP для выбора из следующих функций: ! FREQUENCY (служебное название программы или частота) ! BRDCST INFO (служебное название программы/информация PTY) ! CLOCK (название источника сигнала и часы) Можно настроиться на радиостанцию с помощью информации PTY (типа программы). Поиск станции RDS с помощью информации PTY Можно выполнять поиск общих радиовещательных программ, например, тех, что перечислены в следующем разделе. См. стр. 85. (список). 1 Нажмите 2 Кнопкой M.C. выберите тип программы. NEWS/INFO—POPULAR—CLASSICS—OTHERS 3 Нажмите M.C., чтобы начать поиск. Устройство начинает поиск радиостанций, передающих данный тип программ. При обнаружении радиостанции на дисплее будет показано название данной программы. ! Для отмены поиска нажмите M.C. еще раз. ! Программы некоторых радиостанций могут отличаться от программ, указанных в передаваемом коде PTY. ! Если ни одна из станций не передает программы нужного типа, то на дисплее в течение примерно двух секунд будет показано NOT FOUND, и затем тюнер перейдет в режим приема станции, с которой был начат поиск. Список PTY NEWS/INFO (новости и информация) NEWS (новости), AFFAIRS (текущая информация), INFO (информация), SPORT (спорт), WEATHER (погода), FINANCE (финансы) POPULAR (поп-музыка) POP MUS (поп-музыка), ROCK MUS (рок-музыка), EASY MUS (легкая музыка), OTH MUS (прочие музыкальные жанры), JAZZ (джаз), COUNTRY (кантри), NAT MUS (национальная музыка), OLDIES (золотая коллекция), FOLK MUS (народная музыка) CLASSICS (классика) L. CLASS (легкая классическая музыка), CLASSIC (классическая музыка) OTHERS (прочее) EDUCATE (образовательные программы), DRAMA (постановки), CULTURE (культура), SCIENCE (наука), VARIED (разное), CHILDREN (детские программы), SOCIAL (социальные вопросы), RELIGION (религиозные программы), PHONE IN (ток-шоу), TOURING (путешествия), LEISURE (отдых), DOCUMENT (документальные программы) Настройка функций 1 Нажмите M.C., чтобы открыть главное меню. 2 Поворачивайте M.C. для прокрутки пунктов меню; нажмите, чтобы выбрать FUNCTION. 3 Для выбора функции поворачивайте M.C. Следующие выбранные функции можно настраивать. # В диапазонах MW/LW можно выбрать только BSM, LOCAL и SEEK. 02 BSM (запоминание лучших станций) Функция BSM (запоминание лучших станций) позволяет автоматически сохранять в памяти устройства шесть станций с самым мощным сигналом в порядке убывания его мощности. 1 Нажмите M.C., чтобы включить функцию BSM. Для отмены режима нажмите M.C. еще раз. REGION (региональный) При использовании функции AF функция региональных программ ограничивает выбор станциями, транслирующими региональные программы. 1 Нажмите M.C., чтобы включить или выключить функцию региональных программ. LOCAL (настройка с местным поиском) Настройка с местным поиском позволяет Вам настраиваться только на радиостанции с достаточно мощными сигналами для качественного приема. 1 Нажмите M.C. для выбора нужной настройки. FM: OFF—LV1—LV2—LV3—LV4 MW/LW: OFF—LV1—LV2 Настройка самого высокого уровня позволяет осуществлять прием только станций с самым сильным сигналом, а уменьшение уровня настройки позволяет принимать станции с более слабым сигналом. TA (режим ожидания дорожных сводок) 1 Нажмите M.C., чтобы включить или выключить режим ожидания дорожных сводок. AF (поиск альтернативных частот) 1 Нажмите M.C., чтобы включить или выключить функцию AF. Русский Примечания ! Если служебное название программы в поле FREQUENCY отсутствует, вместо него отображается канал. Если служебное название программы обнаружено, оно будет отображаться. ! Текстовая информация BRDCST INFO будет изменяться автоматически. ! Текстовая информация может меняться в зависимости от диапазона. ! Возможность внесения изменений в текстовую информацию зависит от региона. Использование функций PTY Управление данным устройством NEWS (прерывание для передачи новостей) Ru <QRD3143-C> 85 85 Black plate (86,1) Раздел Управление данным устройством 02 1 Нажмите M.C., чтобы включить или выключить функцию НОВОСТИ. SEEK (настройка левой и правой кнопок) Правой и левой кнопкам на устройстве можно назначить определенную функцию. Выберите MAN (ручная настройка) для ручной настройки или PCH (предустановленный канал) для переключения между заранее настроенными каналами. 1 Нажмите кнопку M.C., чтобы выбрать MAN или PCH. CD/CD-R/CD-RW Основные операции Воспроизведение CD/CD-R/CD-RW 1 Вставьте диск в щель для загрузки маркированной стороной вверх. Извлечение диска CD/CD-R/CD-RW 1 Нажмите h. Выбор папки 1 Нажмите кнопку 1/ или 2/ . Выбор дорожки 1 Нажмите кнопку c или d. Ускоренная перемотка вперед или назад 1 Нажмите и удерживайте кнопку c или d. ! При воспроизведении сжатых аудиофайлов звук не воспроизводится, если включена ускоренная перемотка вперед или назад. Возврат к корневой папке 1 Нажмите и удерживайте BAND. Переключение между сжатыми аудиофайлами и диском CD-DA 1 Нажмите BAND. 86 Переключение дисплея Выбор текстовой информации 1 Нажимайте DISP для выбора из следующих функций: CD-DA ! ELAPSED TIME (номер дорожки и время воспроизведения) ! CLOCK (название источника сигнала и часы) ! SPEANA (анализатор спектра) CD-TEXT ! TRACK INFO (название дорожки/исполнитель/название диска) ! ELAPSED TIME (номер дорожки и время воспроизведения) ! CLOCK (название источника сигнала и часы) ! SPEANA (анализатор спектра) MP3/WMA/WAV ! TRACK INFO (название дорожки/имя исполнителя/название альбома) ! FILE INFO (название папки/название файла) ! ELAPSED TIME (номер дорожки и время воспроизведения) ! CLOCK (название источника сигнала и часы) ! SPEANA (анализатор спектра) Примечания ! Текстовая информация TRACK INFO и FILE INFO будет изменяться автоматически. ! В зависимости от версии iTunes, используемой для записи файлов МР3 на диск, или от типа медиафайла текстовая информация несовместимого формата, записанная в аудиофайле, может отображаться некорректно. ! Возможность внесения изменений в текстовую информацию зависит от типа носителя. Управление данным устройством Выбор и воспроизведение фалов/дорожек из списка 1 Нажмите кнопку , чтобы отобразить список названий файлов/дорожек. 2 С помощью M.C. выберите нужное имя файла (или папки). Выбор файла или папки 1 Поворачивайте M.C. Воспроизведение 1 Выберите файл или дорожку и нажмите M. C. Просмотр списка названий файлов (папок) в выбранной папке 1 Выберите папку и нажмите M.C. Воспроизведение композиции из выбранной папки 1 Выберите папку, затем нажмите и удерживайте M.C. Функции с использованием специальных кнопок Выбор диапазона повторного воспроизведения 1 Нажимайте кнопку 6/ для выбора из следующих функций: ! ALL – Повторное воспроизведение всех дорожек ! ONE – Повтор текущей дорожки ! FLD – Повтор текущей папки Воспроизведение дорожек в произвольной последовательности , чтобы включить или 1 Нажмите кнопку 5/ выключить функцию воспроизведения в произвольной последовательности. Данная функция позволяет воспроизводить дорожки в произвольной последовательности в пределах выбранного диапазона повторного воспроизведения. ! Для переключения на следующую дорожку во время воспроизведения в произвольной последовательности нажмите кнопку d. При нажатии на кнопку c воспроизведение текущей дорожки начинается с начала. Приостановка воспроизведения 1 Нажмите кнопку 4/PAUSE, чтобы включить паузу или возобновить воспроизведение. Улучшение качества звука сжатых аудиофайлов и восстановление полноты звучания (технология преобразования звука) 1 Нажимайте кнопку 3/S.Rtrv для выбора из следующих функций: 1—2—OFF (выкл) Настройка 1 эффективна для файлов с низкой степенью сжатия, а настройка 2 – для файлов с высокой степенью сжатия. Ru <QRD3143-C> 86 Black plate (87,1) Раздел Управление данным устройством Настройка функций 1 Нажмите M.C., чтобы открыть главное меню. 2 Поворачивайте M.C. для прокрутки пунктов меню; нажмите, чтобы выбрать FUNCTION. Выбранные функции, которые можно настраивать, перечислены ниже. S.RTRV (sound retriever, технология преобразования звука) Автоматически улучшает качество звука сжатых аудиофайлов и восстанавливает полноту звучания. 1 Нажмите M.C. для выбора нужной настройки. Подробную информацию см. в Улучшение качества звука сжатых аудиофайлов и восстановление полноты звучания (технология преобразования звука) на стр. 86. Регулировки параметров звука 1 Нажмите M.C., чтобы открыть главное меню. 2 Поворачивайте M.C. для прокрутки пунктов меню; нажмите, чтобы выбрать AUDIO. 3 Для выбора аудиофункции поворачивайте M.C. Следующие выбранные аудиофункции можно настраивать. FADER (регулировка баланса) 1 Для отображения установочного меню нажмите M.C. 2 Нажмите M.C., чтобы отрегулировать баланс передних и задних громкоговорителей. BALANCE (регулировка баланса) 1 Для отображения установочного меню нажмите M.C. 2 Поворачивайте M.C., чтобы отрегулировать баланс левого/правого громкоговорителей. EQ SETTING (вызов настроек эквалайзера) 1 Для отображения установочного меню нажмите M.C. 2 Нажмите кнопку M.C., чтобы выбрать эквалайзер. POWERFUL—NATURAL—VOCAL—CUSTOM1—CUSTOM2—FLAT—SUPER BASS Полосу и уровень эквалайзера можно отрегулировать, если выбрано CUSTOM1 или CUSTOM2. При выборе CUSTOM1 или CUSTOM2 выполните действия, описанные ниже. При выборе других настроек нажмите M.C., чтобы вернуться к предыдущему дисплею. ! CUSTOM1 можно настраивать отдельно для каждого источника сигнала. ! CUSTOM2 - это общая настройка, используемая для всех источников сигнала. 3 Для отображения установочного меню нажмите M.C. 4 Нажимайте M.C. для выбора из следующих функций: Полоса эквалайзера—Уровень эквалайзера 5 Поворачивайте M.C. для выбора настройки. Полоса эквалайзера: 80HZ—250HZ— 800HZ—2.5KHZ—8KHZ Уровень эквалайзера: от +6 до –6 ! Кроме того, можно выбрать эквалайзер, на. жимая кнопку LOUDNESS (тонкомпенсация) Тонкомпенсация компенсирует недостаточное звуковое давление в нижнем и верхнем диапазонах частот на низкой громкости. 1 Нажмите M.C. для выбора нужной настройки. OFF (выкл)—LOW (низкий)—MID (средний) —HI (высокий) 02 Это устройство имеет выход канала сабвуфера, который можно включать и выключать. 1 Нажмите M.C. для выбора нужной настройки. NOR (нормальная фаза)—REV (обратная фаза)—OFF (сабвуфер выключен) SUB.W CTRL (настройка сабвуфер) На выходе сабвуфера будут воспроизводиться только те частоты, которые ниже указанных частот среза. 1 Для отображения установочного меню нажмите M.C. 2 Нажимайте M.C. для выбора из следующих функций: Частота среза—Уровень выходного сигнала—Крутизна характеристики Изменяемые значения будут мигать. 3 Поворачивайте M.C. для выбора настройки. Частота среза: 50HZ—63HZ—80HZ—100HZ —125HZ—160HZ—200HZ Уровень выходного сигнала: от –24 до +6 Крутизна характеристики: –6— –12 BASS BOOST (усиление нижних звуковых частот) 1 Для отображения установочного меню нажмите M.C. 2 Поворачивайте M.C. для выбора нужного уровня. При увеличении или уменьшении уровня отображаются надписи с 0 до +6. HPF SETTING (настройка фильтра верхних частот) Русский ! Функция FADER недоступна, если в режиме SP-P/O MODE выбрано SUB.W/SUB.W. Подробнее см. в разделе SP-P/O MODE (настройка выхода заднего канала и предварительного усилителя) на стр. 89. ! Функции SUB.W, SUB.W CTRL и HPF SETTING недоступны, если в режиме SP-P/O MODE выбрано REAR/REAR. Подробнее см. в разделе SP-P/O MODE (настройка выхода заднего канала и предварительного усилителя) на стр. 89. ! Функции SUB.W CTRL и HPF SETTING недоступны, если в режиме OFF выбрано SUB.W. Подробнее см. в разделе SUB.W (включение/выключение сабвуфера) на стр. 87. Управление данным устройством SUB.W (включение/выключение сабвуфера) Ru <QRD3143-C> 87 87 Black plate (88,1) Раздел Управление данным устройством 02 Если Вы не хотите, чтобы низкочастотные звуки из диапазона частот выхода канала сабвуфера воспроизводились из передних или задних громкоговорителей, включите HPF (фильтр верхних частот). В этом случае из передних или задних громкоговорителей будут воспроизводиться только звуки с частотой выше заданной. 1 Для отображения установочного меню нажмите M.C. 2 Нажимайте M.C. для выбора из следующих функций: Частота среза—Крутизна характеристики 3 Поворачивайте M.C. для выбора настройки. Частота среза: OFF—50HZ—63HZ—80HZ— 100HZ—125HZ—160HZ—200HZ Крутизна характеристики: –6— –12 SLA (регулировка уровня входного сигнала) SLA (функция настройки уровня входного сигнала) позволяет регулировать уровень громкости каждого источника сигнала, чтобы предотвратить резкие изменения громкости при переключении источников сигнала. ! Настройки основываются на уровне громкости FM-тюнера, который остается неизменным. ! Регулировку уровня громкости в диапазоне MW/LW также можно производить с помощью данной функции. ! При выборе FM-тюнера в качестве источника сигнала функция SLA недоступна. 1 Для отображения установочного меню нажмите M.C. 2 Поворачивая M.C., отрегулируйте уровень громкости источника сигнала. Диапазон настройки: от +4 до –4 Меню системы 1 Для отображения установочного меню нажмите M.C. 2 Нажимайте M.C., чтобы выбрать сегмент дисплея часов, который нужно установить. Часы—Минуты 3 Поворачивайте M.C., чтобы отрегулировать время. Важно PW SAVE (режим энергосбережения) отключается при отсоединении аккумуляторной батареи автомобиля; при подсоединении батареи его потребуется включить снова. При выключенном режиме PW SAVE (режим энергосбережения) возможно, что, в зависимости от метода подключения, устройство будет потреблять энергию аккумулятора, если зажигание автомобиля не имеет положения АСС. 1 Нажмите M.C. для выбора нужной настройки. 12H (12-часовой)—24H (24-часовой) 1 Нажмите M.C., чтобы открыть главное меню. AUTO PI (автоматический поиск по идентификатору программы) 2 Поворачивайте M.C. для прокрутки пунктов меню; нажмите, чтобы выбрать SYSTEM. 3 Для выбора функции меню системы поворачивайте M.C. Следующие выбранные функции меню системы можно настраивать. LANGUAGE (выбор языка) Данное устройство может отображать текстовую информацию из сжатых аудиофайлов, в том числе информацию на английском и русском языках. ! При несовместимости настроек встроенного и выбранного языка возможны искажения при выводе текстовых сообщений. ! Некоторые символы могут отображаться неправильно. 1 Поворачивайте M.C. для выбора настройки. ENG (английский)—РУС (русский) CLOCK SET (установка часов) 88 Управление данным устройством 12H/24H (формат отображения времени) Устройство может автоматически искать другую станцию с такой же программой даже во время вызова предварительной настройки. 1 Нажмите M.C., чтобы включить или выключить автоматический поиск по идентификатору программы. AUX (вспомогательный вход) Активируйте эту настройку при подключении к данному устройству вспомогательного устройства. 1 Нажмите M.C., чтобы включить или выключить функцию AUX. MUTE MODE (режим приглушения звука) Звук/уровень звукового сигнала данной системы автоматически понижается при получении сигнала от оборудования с функцией приглушения звука. 1 Для отображения установочного меню нажмите M.C. 2 Поворачивайте M.C. для выбора настройки. Можно выбрать любую настройку из следующего списка: ! MUTE – приглушение звука ! 20dB ATT – ослабление уровня сигнала (20dB ATT имеет более сильный эффект, чем 10dB ATT) ! 10dB ATT – ослабление уровня сигнала PW SAVE (энергосбережение) Включение этой функции позволяет снизить потребляемую мощность аккумуляторной батареи. ! При включении этой функции единственной возможной операцией является включение источника сигнала. 1 Нажмите M.C., чтобы включить или выключить функцию энергосбережения. Настройка регулятора освещенности Можно настроить яркость и подсветку. 1 Нажмите M.C., чтобы открыть главное меню. 2 Поверните M.C., чтобы отобразить ILLUMI, затем нажмите. 3 Нажмите M.C. для выбора нужной настройки. OFF (выкл)—ON (вкл) Ru <QRD3143-C> 88 Black plate (89,1) Раздел Управление данным устройством ! Вы также можете выбрать другую настройку регулятора освещенности, удер/DIMMER. живая нажатой кнопку Стартовое меню 1 Нажмите и удерживайте кнопку SRC/ OFF, пока устройство не выключится. 2 Нажмите кнопку SRC/OFF и удерживайте ее, пока не откроется стартовое меню. 3 Поворачивайте M.C. для прокрутки пунктов меню; нажмите, чтобы выбрать INITIAL. 4 Для выбора функции меню системы поворачивайте M.C. Следующие выбранные функции стартового меню можно настраивать. FM STEP (шаг настройки в FM-диапазоне) Обычно шаг настройки в FM-диапазоне, используемый при настройке с поиском, составляет 50 кГц. При включении функции AF или TA шаг настройки автоматически меняется на 100 кГц. При включенной функции AF предпочтительно установить шаг настройки 50 кГц. ! Во время ручной настройки шаг настройки составляет 50 кГц. 1 Нажмите M.C., чтобы выбрать шаг настройки в FM-диапазоне. 50 (50 кГц)—100 (100 кГц) SP-P/O MODE (настройка выхода заднего канала и предварительного усилителя) Выход на провода заднего громкоговорителя и выход заднего канала RCA можно использовать для подключения широкополосного громкоговорителя или сабвуфера. Выберите настройку, подходящую для Вашего соединения. 1 Для отображения установочного меню нажмите M.C. 2 Поворачивайте M.C. для выбора настройки. Можно выбрать любую настройку из следующего списка: ! REAR/SUB.W – Выберите, если к выходу заднего канала подсоединен широкополосный громкоговоритель, и также имеется сабвуфер, подсоединенный к выходу RCA. ! SUB.W/SUB.W – Выберите, если сабвуфер подключен напрямую к выходу заднего канала без дополнительного усилителя, и также имеется сабвуфер, подсоединенный к выходу RCA. ! REAR/REAR – Выберите, если широкополосный громкоговоритель подсоединен к выходу заднего канала и к выходу RCA. Если к выходу заднего канала подсоединен широкополосный громкоговоритель, а выход RCA не используется, можно выбрать REAR/SUB.W или REAR/ REAR. Меню системы 2 Нажмите кнопку SRC/OFF и удерживайте ее, пока не откроется стартовое меню. 3 Поворачивайте M.C. для прокрутки пунктов меню; нажмите, чтобы выбрать SYSTEM. 4 Для выбора функции меню системы поворачивайте M.C. Следующие выбранные функции меню системы можно настраивать. Подробную информацию см. в Меню системы на стр. 88. Использование дополнительного источника сигнала (AUX) 02 1 Нажмите M.C., чтобы открыть главное меню. 2 Поворачивайте M.C. для прокрутки пунктов меню; нажмите, чтобы выбрать SYSTEM. 3 Поверните M.C., чтобы отобразить DEMO OFF, затем нажмите. 4 Поверните M.C. для выбора YES. 5 Нажмите M.C. для выбора. 1 Вставьте мини-штекер стереокабеля в гнездо AUX. 2 Нажмите кнопку SRC/OFF, чтобы выбрать AUX в качестве источника сигнала. Примечание Невозможно выбрать AUX, если не включена вспомогательная настройка. Подробную информацию см. в разделе AUX (вспомогательный вход) на стр. 88. Переключение дисплея Выбор текстовой информации 1 Нажимайте DISP для выбора из следующих функций: ! Название источника ! Название источника сигнала и часы Если открылся неверный экран Русский 1 Нажмите и удерживайте кнопку SRC/ OFF, пока устройство не выключится. Управление данным устройством Отключите неверный экран, как описано ниже. Ru <QRD3143-C> 89 89 Black plate (90,1) Раздел Установка 03 Установка Соединения F O N OF Важно ! При установке данного устройства в автомобиле, в котором отсутствует положение ключа зажигания АСС, красный кабель должен быть подключен к клемме, которая определяет рабочее положение ключа зажигания; в противном случае может возникнуть утечка тока аккумуляторной батареи. STAR T Положение ACC Положение ACC отсутствует ! Эксплуатация данного устройства в условиях, отличных от описанных ниже, может привести к пожару или сбою в работе устройства. — Транспортные средства с 12-вольтовым аккумулятором и заземлением отрицательного полюса. — Громкоговорители с 50 Вт (выходная мощность) и от 4 W до 8 W (сопротивление). ! Во избежание короткого замыкания, перегрева или неисправностей обязательно соблюдайте следующие указания. — Перед установкой отсоедините отрицательную клемму аккумулятора. — Закрепите провода при помощи зажимов или изоляционной ленты. Для защиты проводки заизолируйте провода в местах их соприкосновения с металлическими деталями. — Разместите все кабели в удалении от подвижных деталей, таких как рычаг переключения передач и направляющие сидений. — Разместите все кабели в удалении от нагревающихся деталей, таких как решетка обогревателя. 90 — Запрещается подключать желтый провод дисплея к аккумуляторной батарее автомобиля через сверленое отверстие в отсеке двигателя. — Изолируйте концы всех не подсоединенных кабелей изоляционной лентой. — Не укорачивайте кабели. — Никогда не срезайте изоляцию со шнура питания данного устройства с целью подачи питания на другое устройство. Допустимая нагрузка кабеля по току ограничена. — Используйте предохранитель с указанными параметрами. — Запрещается напрямую заземлять отрицательный вывод громкоговорителя. — Запрещается связывать вместе отрицательные кабели нескольких громкоговорителей. ! При включении питания устройства управляющий сигнал подается через синебелый провод. Подключите этот провод к клемме пульта управления внешнего усилителя мощности или клемме реле управления антенны с электроприводом (макс. 300 мА 12 В постоянного тока). Если автомобиль оборудован встроенной в оконное стекло антенной, подсоедините провод к клемме питания усилителя антенны. ! Запрещается подсоединять сине-белый кабель к клемме питания внешнего усилителя мощности. Также запрещается подсоединять данный провод к клемме питания антенны с электроприводом. В противном случае может возникнуть утечка тока аккумуляторной батареи или иная неисправность. ! Черный кабель является заземляющим. Заземляющие кабели данного устройства и других устройств (особенно устройств, предназначенных для эксплуатации при больших токах, таких как усилитель мощности) должны монтироваться отдельно. В противном случае их случайное отсоединение может привести к пожару или неисправности. Шнур питания 2 Данное устройство 1 2 7 3 4 5 6 3 4 5 6 1 8 a 3 4 9 5 1 Гнездо шнура питания 2 Выход заднего канала или выход сабвуфера 3 Гнездо антенны 4 Плавкий предохранитель (10 A) 5 Вход проводного пульта дистанционного управления Служит для подключения проводного адаптера пульта дистанционного управления (приобретается отдельно). e b c d 1 К гнезду шнура питания 2 В зависимости от типа автомобиля функции 3 и 5 могут отличаться. В этом случае следует подключить 4 к 5 и 6 к 3. 3 Желтый Резервный разъем (или разъем дополнительного оборудования) 4 Желтый Подключите к клемме источника постоянного тока 12 В. 5 Красный Разъем дополнительного оборудования (или резервный разъем) 6 Красный Подключите к клемме, на которую подается напряжение (12 В постоянного тока) при включении зажигания. 7 Подсоедините провода одинакового цвета друг к другу. 8 Черный (заземление на массу) Ru <QRD3143-C> 90 Black plate (91,1) Раздел Установка Примечания ! Требуется изменение стартового меню данного устройства. См. SP-P/O MODE (настройка выхода заднего канала и предварительного усилителя) на стр. 89. Выход сабвуфера данного устройства монофонический. ! При использовании сабвуфера мощностью 70 Вт (2 W) обязательно подсоедините к сабвуферу фиолетовый и фиолетовый/черный провод данного устройства. Не подсоединяйте зеленый и зеленый/черный провода. Усилитель мощности (приобретается отдельно) Используйте данную схему подсоединения при использовании дополнительного усилителя мощности. ! Не используйте детали, не разрешенные производителем к использованию, поскольку это может стать причиной неисправностей. ! Уточните у дилера компании, требует ли установка сверления отверстий или внесения иных изменений в конструкцию автомобиля. ! Не устанавливайте данное устройство в местах, где оно может: — помешать управлению автомобилем. — травмировать пассажира при внезапной остановке автомобиля. ! Перегрев полупроводникового лазера приведет к его выходу из строя. Разместите все кабели в удалении от нагревающихся деталей, таких как решетка обогревателя. ! Оптимальной является установка устройства под углом менее 60°. 3 1 5 03 2     60° 4 Установка Для данного изделия предусмотрена возможность установки с помощью переднего или заднего крепления. При установке используйте детали, имеющиеся в продаже. Переднее крепление стандарта DIN 1 Вставьте монтажную обойму в переднюю панель. При установке в недостаточно глубоком гнезде используйте монтажную обойму, входящую в комплект поставки устройства. При наличии достаточного пространства за устройством применяется монтажная обойма, поставляемая вместе с автомобилем. 2 Закрепите обойму, подогнув с помощью отвертки металлические язычки (90°). 1 5 1 Пульт дистанционного управления системой Подсоедините синий/белый кабель. 2 Усилитель мощности (приобретается отдельно) 3 Подключите с помощью кабелей RCA (приобретаются отдельно) 4 К выходу заднего канала или выходу сабвуфера 5 Задний громкоговоритель или сабвуфер Переднее/заднее крепление стандарта DIN ! При установке необходимо обеспечить эффективный отвод тепла, оставив достаточное пространство за задней панелью и закрепив свободные кабели так, чтобы они не закрывали вентиляционные отверстия. Оставить просторное место 1 Приборная панель 2 Монтажная обойма # Убедитесь, что устройство надежно закреплено в гнезде. Неустойчивость устройства может привести к его выпадению и неполадкам в работе. 5 см 5 см 2 Русский 9 Синий/белый Расположение штекера разъема ISO на различных автомобилях может отличаться. Если штекер 5 предназначен для управления антенной, подсоедините 9 к b. На других автомобилях подключать 9 к b запрещается. a Синий/белый Подключите к клемме панели управления усилителя мощности (макс. 300 мА 12 В постоянного тока). b Синий/белый Подключите к клемме реле управления антенны с электроприводом (макс. 300 мА 12 В постоянного тока). c Желтый/черный Если используется оборудование, имеющее функцию приглушения звука, данный провод необходимо подсоединить к клемме Audio Mute данного устройства. В противном случае необходимо проследить за тем, чтобы данный провод не контактировал с любыми другими разъемами. d Выводы громкоговорителей Белый: Передний левый + Белый/черный: Передний левый * Серый: Передний правый + Серый/черный: Передний правый * Зеленый: Задний левый + или сабвуфер + Зеленый/черный: Задний левый * или сабвуфер * Фиолетовый: Задний правый + или сабвуфер + Фиолетовый/черный: Задний правый * или сабвуфер * e Разъем ISO В некоторых автомобилях разъем ISO может иметь два вывода. В этом случае необходимо подсоединить оба разъема. Установка 5cm cm Важно ! Перед окончательной установкой проверьте все соединения и системы. Ru <QRD3143-C> 91 91 Black plate (92,1) Раздел Установка 03 Дополнительная информация Заднее крепление стандарта DIN 1 Совместите отверстия на кронштейне и боковых панелях устройства. 2 Затяните по два винта с каждой стороны. 3 1 2 1 Самонарезающий винт (5 мм × 8 мм) 2 Монтажная рамка 3 Приборная панель или консоль Демонтаж устройства 1 Снимите рамку. 1 Декоративная рамка 2 Язычок ! Снятие передней панели облегчает доступ к декоративной рамке. ! При установке декоративной рамки сторона рамки с язычком должна быть направлена вниз. 3 Вытяните устройство из приборной панели автомобиля. Снятие и установка передней панели В целях защиты от кражи переднюю панель можно снять. Нажмите на кнопку снятия панели и потяните панель вверх и на себя. Чтобы получить дополнительную информацию, см. Снятие передней панели в целях защиты от кражи и Установка передней панели на стр. 84. Устранение неисправностей Признак Причина Действие Дисплей автоматически возвращается в исходный режим. В течение 30 Повторите опесекунд не рацию. было выполнено никаких операций. Диапазон повторного воспроизведения самопроизвольно изменяется. В зависимости от выбранного диапазона воспроизведения он может изменяться при выборе другой папки или дорожки, а также при перемотке вперед/назад. Выберите диапазон повторного воспроизведения еще раз. Вложенная папка не воспроизводится. Вложенные папки не воспроизводятся, если выбран диапазон FLD (повторное воспроизведение папки). Выберите другой диапазон повторного воспроизведения. При изменении дисплея отображается NO XXXX (например, NO TITLE). Текстовая информация отсутствует. Переключите дисплей или включите воспроизведение другой дорожки/ файла. Признак Причина Действие Устройство функционирует с ошибками. Имеются помехи. Рядом с устройством используется прибор, передающий электромагнитные волны, например, сотовый телефон. Уберите прибор, вызывающий помехи, от этого устройства. Сообщения об ошибках Прежде чем обратиться к торговому представителю или в ближайший сервисный центр Pioneer, обязательно запомните сообщение об ошибке. Общие Сообщение Причина AMP ERROR Устройство не работает или неправильно подсоединен громкоговоритель; сработала цепь защиты. Действие Проверьте, подключен ли громкоговоритель. Если сообщение не исчезает даже после выключения/выключения зажигания, свяжитесь с дилерским центром или авторизованным сервисным центром Pioneer. 2 Вставьте прилагаемые экстракторы с обеих сторон устройства до щелчка. 92 Ru <QRD3143-C> 92 Black plate (93,1) Приложение Дополнительная информация Проигрыватель компакт-дисков Сообщение Причина Действие ERROR-07, Диск загряз11, 12, 17, 30 нен. Очистите диск. ERROR-07, 10, 11, 12, 15, 17, 30, A0 Диск поцарапан. Замените диск. Электрическая или механическая неисправность. Установите ключ зажигания в положение OFF, а затем – в положение ON или переключитесь на другой источник сигнала, а затем обратно на проигрыватель компактдисков. Вставлен пустой диск. Замените диск. ERROR-23 Формат диска не поддерживается. Замените диск. FORMAT READ Иногда происходит задержка между началом воспроизведения и появлением звука. Звук появится после того как с дисплея исчезнет сообщение. На диске отсутствуют файлы, которые можно воспроизвести. Замените диск. NO AUDIO SKIPPED Диск содержит Замените диск. файлы, защищенные технологией DRM. Сообщение Причина PROTECT Действие Все файлы на Замените диск. диске защищены технологией DRM. Рекомендации по обращению с изделием Диски и проигрыватель Используйте только диски, имеющие один из следующих логотипов. Не прикасайтесь к записанной поверхности дисков. Когда диски не используются, храните их в футлярах. Не приклеивайте этикеток, не пишите и не наносите химических веществ на поверхность дисков. Для очистки компакт-диска протрите диск мягкой тканью от центра к краю. Конденсация может временно ухудшить работу проигрывателя. Оставьте его для адаптации к более высокой температуре примерно на час. Также удалите влагу с дисков с помощью мягкой ткани. Воспроизведение дисков может быть невозможно из-за характеристик диска, формата диска, приложения, при помощи которого выполнялась запись, условий воспроизведения, условий хранения и других факторов. Используйте диски диаметром 12 см. Не используйте диски диаметром 8 см и адаптеры для воспроизведения таких дисков. Используйте только обычные круглые диски. Не используйте диски необычной формы. Не вставляйте в щель для загрузки компактдиска ничего, кроме компакт-диска. Не используйте диски с трещинами, отколотыми краями, деформированные диски или диски с другими повреждениями, поскольку такие диски могут повредить проигрыватель. Не закрытые для записи диски CD-R/CD-RW воспроизвести нельзя. Толчки от неровностей дороги могут вызвать прерывание воспроизведения диска. Перед использованием дисков ознакомьтесь с мерами предосторожности при обращении с ними. При использовании дисков, на поверхность которых могут наноситься этикетки, изучите инструкции и предупреждения для этих дисков. Установка и извлечение некоторых дисков могут быть невозможны. Использование таких дисков может привести к повреждению оборудования. Не приклеивайте на диски этикетки и другие материалы. ! Это может деформировать диски, в результате чего их воспроизведение будет невозможным. ! Этикетки могут отклеиться во время воспроизведения и затруднить извлечение дисков, а также повредить оборудование. Диски формата DualDisc DualDisc – это двусторонние диски для записи аудиоданных на CD с одной стороны и видеоданных на DVD – с другой. Поскольку сторона CD двойных дисков физически несовместима с общим стандартом компакт-дисков, ее воспроизведение на данном устройстве может быть невозможным. Частая загрузка и извлечение двойного диска может привести к появлению царапин на диске. Серьезные царапины могут создать проблемы при воспроизведении диска на данном устройстве. В некоторых случаях двойной диск может застревать в щели загрузки дисков, из-за чего его становится невозможно извлечь. Во избежание такой ситуации мы рекомендуем воздержаться от использования двойных дисков в данном устройстве. За более подробной информацией о двойных дисках обращайтесь к соответствующим производителям. Совместимость с форматами сжатия данных WMA Расширение: .wma Скорость передачи данных: от 48 кбит/с до 320 кбит/с (постоянная), от 48 кбит/с до 384 кбит/с (переменная) Частота дискретизации: 32 кГц, 44,1 кГц, 48 кГц Windows Media Audio Professional, Lossless, Voice/DRM Stream/Stream с поддержкой видео: не поддерживается Ru <QRD3143-C> 93 Русский ERROR-15 Дополнительная информация 93 Black plate (94,1) Приложение Дополнительная информация MP3 Расширение: .mp3 Скорость передачи данных: от 8 кбит/с до 320 кбит/с (постоянная), переменная Частота дискретизации: от 8 кГц до 48 кГц (32 кГц, 44,1 кГц, 48 кГц пиковая) Совместимая версия тегов ID3: 1.0, 1.1, 2.2, 2.3, 2.4 (теги ID3 версии 2.x имеют приоритет перед версией 1.x.) Списки воспроизведения M3u: не поддерживаются MP3i (интерактивный MP3), mp3 PRO: не поддерживаются Дополнительная информация Дополнительная информация В качестве названия файла или папки могут отображаться только первые 32 символа (включая расширение). Для отображения в данном устройстве кодировка русского текста должна соответствовать одному из следующих наборов символов: ! Юникод (UTF-8, UTF-16) ! Отличный от Юникода набор символов, использующийся в среде Windows, для которого в языковой настройке задан русский язык Это устройство может неверно воспроизводить некоторые файлы формата WMA в зависимости от приложений, использованных для их записи. Последовательность воспроизведения аудиофайлов Разрядность квантования: 8 и 16 (LPCM), 4 (MS ADPCM) Частота дискретизации: от 16 кГц до 48 кГц (LPCM), 22,05 кГц и 44,1 кГц (MS ADPCM) Пример иерархии 01 1 2 Файловая система: ISO 9660 уровень 1 и 2, Romeo, Joliet Воспроизведение нескольких сессий: поддерживается Пакетный формат записи: не поддерживается Независимо от продолжительности паузы между композициями в изначальной записи, при воспроизведении дисков со сжатыми аудиофайлами между композициями будут короткие паузы. 94 03 3 4 04 5 6 Допустимая иерархия папок: до восьми уровней (реальная иерархия папок составляет менее двух уровней) Количество воспроизводимых файлов: не более 999 Д: Б Д: Б :Ъ :Я :Х :Ц :Ч : Ш, Щ :Ы :Ь :Э :Ю Д: Б Авторское право и товарные знаки iTunes Apple и iTunes являются торговыми знаками компании Apple Inc., зарегистрированными в США и других странах. 02 Диск Количество воспроизводимых папок: не более 99 Д: Б Д: Дисплей Б: Буква Пользователь не может назначать номера папок и устанавливать последовательность воспроизведения с помощью данного устройства. WAV Расширение: .wav Д: Б ВНИМАНИЕ Не оставляйте диски в местах с высокой температурой. 05 : Папка : Сжатый аудиофайл от 01 до 05: Номер папки от 1 до 6: Последовательность воспроизведения Диск Последовательность выбора папок и других действий может отличаться в зависимости от кодировки или программного обеспечения, использованного для записи. Таблица символов для русского языка MP3 Поставка этого изделия дает право только на его частное и некоммерческое использование и не предоставляет лицензии и не подразумевает право использования этого изделия в любых коммерческих (т.е. приносящих прибыль) прямых трансляциях (телевизионных, спутниковых, кабельных и/или любых других), вещании/потоковой передаче через Интернет, локальных сетях и/или других сетях или в других электронных системах распространения, таких как системы платного аудио и аудио по запросу. Для такого использования необходима специальная лицензия. Дополнительную информацию см. на сайте http://www.mp3licensing.com. WMA Д: Б Д: Б Д: Б Д: Б Д: Б :А :Б :В :Г :Д : Е, Ё :Ж :З : И, Й :К :Л :М :Н :О :П :Р :С :Т :У :Ф Windows Media – это зарегистрированная торговая марка или торговая марка Microsoft Corporation в США и/или других странах. Ru <QRD3143-C> 94 Black plate (95,1) Приложение Дополнительная информация Дополнительная информация В данном изделии используются технологии, принадлежащие корпорации Microsoft, которые не разрешается использовать или распространять без лицензии от Microsoft Licensing, Inc. Серийный номер На этом рисунке показана информация о месяце и годе изготовления устройства. 12 цифр 10 цифр 2 цифры P1 P2 Дата изготовления оборудования P1 - Год изготовления 2001 2002 Год Символ A B Год Символ 2011 K 2012 L P2 - Месяц изготовления Месяц 1 2 3 Символ A B C 2003 C 2004 D 2005 E 2006 F 2007 G 2008 H 2009 I 2010 J 2013 M 2014 N 2015 O 2016 P 2017 Q 2018 R 2019 S 2020 T 4 D 5 E Технические характеристики Общие 7 G 8 H 9 I 10 J 11 K 12 L Передняя панель ..................... 188 мм × 58 мм × 16 мм D Шасси ............... 178 мм × 50 мм × 165 мм Передняя панель ..................... 170 мм × 46 мм × 16 мм Масса ............................. 1 кг Проигрыватель компакт-дисков Система ......................... Аудиосистема с компакт-диском Используемые диски ..... Компакт-диск Отношение сигнал/шум ................................... 94 дБ (1 кГц) (сеть IEC-A) Число каналов ............... 2 (стерео) Формат декодирования файлов MP3 ................................... MPEG-1 и 2 Audio Layer 3 Формат декодирования файлов WMA ................................... Версии 7, 7.1, 8, 9, 10, 11, 12 (двухканальный звук) (Windows Media Player) Формат сигнала WAV ..... Linear PCM и MS ADPCM (без компрессии) Аудио Максимальная выходная мощность ................................... 50 Вт × 4 70 Вт × 1/2 W (для сабвуфера) FM-тюнер Отношение сигнал/шум ................................... 72 дБ (сеть IEC-A) MW-тюнер Диапазон частот ............. от 531 кГц до 1 602 кГц Полезная чувствительность ................................... 25 мкВ (отношение сигнал/ шум: 20 дБ) Отношение сигнал/шум ................................... 62 дБ (сеть IEC-A) LW-тюнер Диапазон частот ............. от 153 кГц до 281 кГц Полезная чувствительность ................................... 28 мкВ (отношение сигнал/ шум: 20 дБ) Отношение сигнал/шум ................................... 62 дБ (сеть IEC-A) Примечание: В соответствии со статьей 5 закона Российской Федерации «О защите прав потребителей» и постановлением правительства Российской Федерации № 720 от 16.06.97 компания Pioneer Europe NV оговаривает следующий срок службы изделий, официально поставляемых на российский рынок. Автомобильная электроника: 6 лет Прочие изделия (наушники, микрофоны и т.п.): 5 лет Примечания ! Характеристики и конструкция могут быть изменены без предварительного уведомления. ! Данное устройство произведено в Таиланде. Диапазон частот ............. от 87,5 МГц до 108,0 МГц Полезная чувствительность ................................... 9 дБф (0,8 мкВ/75 W, моно, отношение сигнал/шум: 30 дБ) Ru <QRD3143-C> 95 Русский Источник питания ........... 14,4 В постоянного тока (допустимый диапазон от 10,8 В до 15,1 В) Система заземления ..... Заземление отрицательного полюса Максимальный потребляемый ток ................................... 10,0 А Размеры (Ш × В × Г): DIN Шасси ............... 178 мм × 50 мм × 165 мм 6 F Номинальная выходная мощность ................................... 22 Вт × 4 (от 50 Гц до 15 000 Гц, суммарное значение коэффициента нелинейных искажений 5 %, нагрузка 4 W для обоих каналов) Сопротивление нагрузки ................................... 4 W (допустимо – от 4 W до 8 W) Максимальная выходная мощность ................................... 2,0 В Контур громкости ........... +10 дБ (100 Гц), +6,5 дБ (10 кГц) (громкость: –30 дБ) Эквалайзер (5-полосный графический эквалайзер): Частота .................... 80 Гц/250 Гц/800 Гц/ 2,5 кГц/8 кГц Диапазон амплитудно-частотных характеристик .......................... ±12 дБ (с шагом 2 дБ) Сабвуфер (моно): Частота .................... 50 Гц/63 Гц/80 Гц/100 Гц/ 125 Гц/160 Гц/200 Гц Крутизна характеристики ............................ –6 дБ/окт, –12 дБ/окт Усиление ................. +6 дБ до –24 дБ Фаза ........................ Нормальная/Обратная 95 Black plate (96,1) PIONEER CORPORATION 28-8, Honkomagome 2-chome, Bunkyo-ku, Tokyo 113-0021, JAPAN Корпорация Пайонир 28-8, Хонкомагомэ 2-чоме, Бункё-ку, Токио 113-0021, Япония Импортер ООО “ПИОНЕР РУС” 105064, Россия, г. Москва, Нижний Сусальный переулок, дом 5, строение 19 Тел.: +7(495) 956-89-01 PIONEER EUROPE NV Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium/Belgique TEL: (0) 3/570.05.11 PIONEER ELECTRONICS (USA) INC. P.O. Box 1540, Long Beach, California 90801-1540, U.S.A. TEL: (800) 421-1404 PIONEER ELECTRONICS OF CANADA, INC. 340 Ferrier Street, Unit 2, Markham, Ontario L3R 2Z5, Canada TEL: 1-877-283-5901 TEL: 905-479-4411 PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 2 Jalan Kilang Barat, #07-01, Singapore 159346 TEL: 65-6378-7888 PIONEER ELECTRONICS AUSTRALIA PTY. LTD. 5 Arco Lane, Heatherton, Victoria, 3202 Australia TEL: (03) 9586-6300 PIONEER ELECTRONICS DE MÉXICO S.A. de C.V. Blvd.Manuel Ávila Camacho 138, 10 piso Col.Lomas de Chapultepec, México, D.F. 11000 TEL: 52-55-9178-4270 FAX: 52-55-5202-3714 先鋒股份有限公司 台北市內湖區瑞光路407號8樓 電話: 886-(0)2-2657-3588 先鋒電子(香港)有限公司 香港九龍長沙灣道909號5樓 電話: 852-2848-6488 ã 2012-2016 PIONEER CORPORATION. All rights reserved. ã 2012-2016 PIONEER CORPORATION. Tous droits de reproduction et de traduction réservés. ã PIONEER CORPORATION, 2012-2016. Все права защищены. <KOKZ14D> <QRD3143-C> EW <QRD3143-C> 96
1 / 1

Pioneer DEH-150MP Handleiding

Categorie
Auto media-ontvangers
Type
Handleiding
Deze handleiding is ook geschikt voor