Documenttranscriptie

English Quick Reference Guide ■ Accessories The following accessories are supplied with this product. PUSH Remote control Batteries (2) (AAA, R03, UM-4) AM loop antenna Indoor FM antenna VIDEO AUX input cover YPAO microphone Preparing the remote control 1 3 2 1 Take off the battery compartment cover. 2 Insert the two supplied AAA batteries into the battery case, following the polarity markings. 3 Snap the battery compartment cover back into place. Be sure to aim the remote control directly at the remote control sensor on this unit during operation. within 6 m (20 ft) ■ Items necessary for connection Speakers Ex. Front speaker Ex. Ex. Ex. Center speaker Surround speaker Active subwoofer • Use speakers with an impedance of at least 6 Ω. • If you are using a CRT monitor, we recommend that you use magnetically shielded speakers. • Prepare at least two speakers (for front). The priority of the other speakers is as follows: 1 Two surround speakers 2 One center speaker Cable External components • Cables for connecting external components (may differ depending on the components you are connecting) • Speaker cables (a quantity to match the number of speakers you are connecting) • Audio pin cable (for subwoofer) TV Playback device such as BD (Blu-ray Disc)/DVD players -1- Some features are not available in certain regions.  Connect and install as follows the first time you use this unit. See the following explanations for the connections for each number. TV 3 2 BD/DVD player (recorder) 4 This unit Front speaker R Front speaker L Subwoofer 1 Surround speaker R Center speaker 1 Surround speaker L 1 Connect the speakers 2 Connect a TV 3 Connect playback device such as BD/DVD players and recorders 4 Set the VOLTAGE SELECTOR and connect the AC power cable (Asia and General models) Connect the AC power cable (Other models) When connection and installation is finished, set up the speaker parameters automatically 5 . -2-  1 Connect the speakers Front speaker R L Surround speaker R L Caution: • Remove the AC power cord of this unit from the power outlet before connecting the speakers. • Generally speaker cables consist of two parallel insulated cables. One of these cables is a different color, or has a line running along it, to indicate different polarity. Insert the different colored (or lined) cable into the “+” (positive, red) terminal on this unit and the speakers, and the other cable into the “-” (minus, black) terminal. • Be careful that the core of the speaker cable does not touch anything or come into contact with the metal areas of this unit. This may damage this unit or the speakers. If the speaker cables short circuit, “CHECK SP WIRES!” will appear on the front panel display when this unit is switched on. • (U.S.A. and Canada models only) When connecting 6 Ω speakers, set the speaker impedance to 6 Ω on this unit before making connections. Refer to Owner’s Manual for information on settings. SPEAKERS HDMI 3 HDMI 4 FRONT CENTER SURROUND SINGLE SURROUND BACK AUDIO OUT SUBWOOFER PRE OUT Center speaker Subwoofer Connecting the speakers 2 Connecting the subwoofer 3 FR ON T 1 Connect the subwoofer input jack to the SUBWOOFER jack on this unit with an audio pin cable. 2 Set the subwoofer volume as follows. 1 4 1 Remove approximately 10 mm of insulation from the ends of the speaker cables, and twist the bare wires of the cables together firmly so that they will not cause short circuits. 2 Loosen the speaker terminals. 3 Insert the bare wire of the speaker cable into the gap on the side of the terminal. 4 Tighten the terminal. Volume: Set to approximately half volume (or slightly less than half). Crossover frequency (if available): Set to maximum. VOLUME MIN MAX CROSSOVER/ HIGH CUT MIN MAX Subwoofer examples Connecting the banana plug (Except U.K., Europe, Asia and Korea models) When using the 7.1/6.1-channel surround system Tighten the knob, and then insert the banana plug into the end of the terminal. Connecting an external amplifier to the SURROUND BACK L/R jacks of the PRE OUT terminals allows you to create the maximum of 7.1-channel surround system with a surround back channel. Refer to the Owner’s Manual for information on how to connect the surround back speakers. FR ON T Banana plug -3-  2 Connect a TV Video input to this unit is output to a TV using output jacks of the same kind. Input When you have made connections using different types of video such as HDMI and component video, make the same connection with your TV. When viewing, be sure to switch the input source on your TV to match the playback device. Output HDMI HDMI COMPONENT VIDEO COMPONENT VIDEO VIDEO VIDEO HDMI input Component video input Video input If your TV has multiple inputs, connect with the following priority (A to C). HDMI HDMI COMPONENT VIDEO PR HDMI PB (BD/DVD) HDMI OUT DOCK HDMI 1 ANTENNA HDMI 2 VIDEO HD V COMPONENT VIDEO COMPONENT VIDEO FM A When using an HDMI compatible TV. Y GND AM PR PR PR PR PB 75ǡ PB COMPONENT VIDEO PR PB B When using a component PB VIDEO VIDEO PB V Y Y Y V Y Y MONITOR OUT V VIDEO video input-compatible TV. V VIDEO OPTICAL COAXIAL COAXIAL OPTICAL (CD) ( TV ) A 1 AV AV A 2 AV A 3 AV A 4 AV A 5 A AV OUT AV 6 A V AUDIO 1 C When using a TV compatible with video input only. AUDIO 2 Listening to TV audio To playback TV audio on this unit, connect the TV audio output to this unit. When using an HDMI compatible TV that supports Audio Return Channel functions and / or HDMI Control functions (Ex. Panasonic VIERA Link), you can enjoy the TV sound on this unit as follows: Connect the following input jacks, matching the audio output jacks on your TV. When viewing your TV, select the appropriate input source on this unit. OPTICAL When using a TV that supports the Audio Return Channel functions and HDMI Control functions The audio / video output from the unit to the TV and audio output from the TV to the unit are possible using a single HDMI cable. The input source is switched automatically to match operations carried out on the TV, and that makes TV sound control easier to use. For the connections and settings, refer to “Using the HDMI Control function” in Owner’s Manual. DOCK O COMPONENT VIDEO PR Audio output PB VIDEO Y O OPTICAL COAXIAL COAXIAL OPTICAL (CD) ( TV ) AV 1 AV 2 AV 3 AV 4 AV 5 When using a TV that supports HDMI Control functions Audio output from TV Input jack on this unit Optical digital output AV1 or AV4 Coaxial digital output AV2 or AV3 Analog output One of AV5, AV6, AUDIO1, AUDIO2, and V-AUX HDMI Audio Return Channel (Described in the right column) HDMI OUT When HDMI Control functions are enabled on the unit, input source can be switched automatically to match operations carried out on the TV. For the connections and settings, refer to “Using the HDMI Control function” in Owner’s Manual. ✽ Connecting to AV4 allows you to playback TV audio just by pressing the “TV” under “SCENE” key. -4-  3 Connect playback device such as BD/DVD players and recorders If your playback device has multiple audio/video outputs, connect with the following priority (A to D) to enjoy a higher quality sounds and images. A When playback device is HDMI HDMI capable of HDMI output HDMI B When playback device is capable of component video output (with optical digital audio output) COMPONENT VIDEO PR PB (BD/DVD) HDMI OUT DOCK HDMI 1 ANTENNA Y FM OPTICAL PR PR PR PB PB PB Y Y HDMI 2 GND AM PR O 75ǡ PB VIDEO VIDEO C When playback device is capable of component video output (with coaxial digital audio output) D When playback device is capable of video output (with analog audio output) only • • • • HDMI 3 COMPONENT VIDEO COMPONENT VIDEO V Y Y COMPONENT VIDEO MONITOR OUT PR L PB R O Y COAXIAL C OPTICAL COAXIAL COAXIAL OPTICAL (CD) ( TV ) AV 1 AV 2 AV 3 A A 4 AV AV 5 A 6 AV A AV OUT AUDIO 1 AUDIO 2 C VIDEO V AUDIO L R When playback, select the corresponding input source the jack is connected. Connecting to HDMI1 allows you to select the HDMI input just by pressing the “BD/DVD” under “SCENE” key. Connecting to AV3 allows you to select the AV3 input just by pressing the “CD” under “SCENE” key. If necessary, you can connect components that cannot be connected using the above methods, such as devices that output video from component video output jacks and audio from analog output jacks. Refer to Owner’s Manual for details. Set the VOLTAGE SELECTOR and connect the AC power cable 4 (Asia and General models) Connect the AC power cable (Other models) (Asia and General models only) Select the switch position according to your local voltage using a straight slot screwdriver. (General model) Voltages are AC 110/120/220/230-240 V, 50/60 Hz. VOLTAGE SELECTOR To the power outlet VOLTAGE SELECTOR (Asia model) Voltages are AC 220/230-240 V, 50/60 Hz. AC power cable Caution The VOLTAGE SELECTOR on the rear panel of this unit must be set for your local voltage BEFORE plugging the power cable into the AC wall outlet. Improper setting of the VOLTAGE SELECTOR may cause damage to this unit and create a potential fire hazard. -5-  5 Set up the speaker parameters automatically (YPAO) When connection is finished, adjust the status, sizes, and volume balance of the speakers to provide an optimal sound field. This unit is equipped with a YPAO (Yamaha Parametric Room Acoustic Optimizer) function that adjusts the speaker balance automatically with a simple procedure. When you use YPAO, a test tone will be output from the speakers for approximately 3 minutes and acoustic measuring will be performed. When using YPAO, be careful of the following. • The test tone is output at high volume. Please refrain from using this function at night when it may be a nuisance to others nearby. • Please take care that the test tone does not frighten any small children. 1 Check the following before using YPAO. This unit • The headphones are removed. Subwoofer • The power is turned on. • Volume is set to approximately half, and the cross-over frequency (if present) is set to maximum. CROSSOVER/ HIGH CUT VOLUME MIN MIN MAX MAX Subwoofer examples 2 Place the supplied YPAO microphone at ear height in your listening position. YPAO microphone When positioning the microphone, we recommend that you use equipment that allows you to adjust the height (such as a tripod) as a microphone stand. When using a tripod, use the tripod screws to fix the microphone in place. 3 Press RECEIVER A on the remote control to switch this unit on. Continues to the next page -6-  4 Connect the YPAO microphone to the YPAO MIC jack on the front panel. CODE SET TRANSMIT SOURCE RECEIVER SLEEP YPAO MIC RECEIVER A HDMI 1 2 3 4 1 2 3 4 5 6 1 2 V-AUX V VAUX [ A ] [ B ] DOCK PRESET TUNING INFO A AV AUDIO YPAO microphone TUNER “MIC ON. YPAO START” appears on the front panel display, and then changes to display the following. YPAO AM MEMORY MOVIE MUSIC ENHANCER SUR. DECODE STEREO STRAIGHT VOL. SW C R L SL SR SBL SBR bPressb[SETUP] DIRECT SCENE BD DVD TV CD SETUP This completes preparations. To achieve more accurate results, be careful of the following when measuring. • Measuring will take approximately 3 minutes. Keep the room as quiet as possible during measurement. • Wait in the corner of the listening room during measurement or leave it entirely, to avoid becoming an obstruction between the speakers and the YPAO microphone. 5 FM INFO Press SETUP on the remote control to start measurement. RADIO SETUP VOLUME ENTER OPTION ENTER RETURN DISPLAY A POP-UP MENU TOP MENU MUTE REC 1 2 3 5 6 7 9 0 10 4 8 ENT TV INPUT Progress YPAO TV VOL TV CH MUTE VOL. Progress SW C R L SL SR SBL SBR 02% The following display appears if measurement finishes without any problems. YPAO VOL. YPAO Complete L SL SW C R SR You can use the following functions with this unit. For details on the operations, refer to Owner's Manual on the supplied CD-ROM. Note When a problem occurs, an error message or a warning message appears either during or after measurement. Refer to “Set up the speaker parameters automatically (YPAO)” in Owner’s Manual to solve the problem, and carry out YPAO again. 6 Press ENTER on the remote control to apply the results of measurement. YPAO VOL. Disconnect MIC 7 ■ Various parameter adjustment to match your listening environment L SL SW C R SR - Sound quality control with the equalizer <Graphic Equalizer> - Easy listening at low volumes <Adaptive DRC> - Adjusting volume between input sources <Volume Trim> ■ External device connection and playback - Connections and playback from BD/DVD players (recorders), TV audio, and other devices - Playback from an iPod/iPhone - Playback from a Bluetooth device Remove the YPAO microphone. YPAO finishes automatically when the YPAO microphone is removed. ■ FM/AM tuner - Simple preset tuning - (U.K. and Europe models) Radio Data System tuning - (U.K. and Europe models) Automatic traffic information reception - (Asia and General models only) Changing FM/AM frequency steps initializing various settings for this unit YPAO MIC INFO etc. -7-  Operation guide ② ① ③ ⑥ YPAO MIC ④ DIRECT INFO MEMORY PRESET FM AM TUNING VOLUME SCENE BD DVD PHONES INPUT TV TONE CONTROL CD PROGRAM RADIO VIDEO AUX STRAIGHT SILENT CINEMA PORTABLE ⑦ VIDEO L AUDIO R ③ ① 1 Switches this unit between on and standby mode This unit switches between on and standby mode every time you press this key. CODE SET TRANSMIT 2 Choose an input source to listen to SOURCE RECEIVER The name of the selected input source appears on the front panel display. SLEEP VOL. HDMI1 HDMI L SL SW C 1 2 R SR 3 4 3 4 AV 1 2 AUDIO 3 Select sound field programs and sound decoders Front panel Remote control Description 1 2 [ B ] DOCK PRESET TUNING FM AM INFO MEMORY MOVIE MUSIC Selects sound field programs optimized for appreciating music. MUSIC PROGRAM STEREO SUR. DECODE TV CD SETUP Switches to direct mode for faithful reproduction of audio. RETURN ⑥ The current volume level is displayed on the front panel display. RADIO VOLUME ④ MUTE ⑤ DISPLAY POP-UP MENU TOP MENU 4 Adjusts the volume level ③ OPTION ENTER DIRECT DIRECT SCENE BD DVD Switches to straight decoding mode for stereo/multi-channel playback without using a sound field program. STRAIGHT STEREO STRAIGHT Selects surround decoders such as Dolby Pro Logic II. STRAIGHT ② ENHANCER SUR. DECODE Selects settings for stereo playback or enhancers for compressed audio. ENHANCER DIRECT 6 [ A ] TUNER Selects sound field programs optimized for viewing movies, dramas, and sports. MOVIE 5 V-AUX REC VOL. Volume -18.5dB L SL SW C R SR 5 Mutes the sound 1 2 3 4 5 6 7 8 9 0 The indicator blinks while the sound is muted. 10 ENT TV INPUT TV VOL 6 Switches between input settings TV CH MUTE You can switch input sources and sound field programs with a single key. SCENE BD/DVD TV CD RADIO Input HDMI 1 AV4 AV3 TUNER Sound field program Straight Straight Straight 7ch Enhancer - Pressing and holding this key allows you to store input sources/sound field programs. - Press this key when this unit is in standby mode to switch on the unit. 7 Adjusting high/low-frequency sound (Tone control) 1 Press TONE CONTROL to select “Treble” or “Bass.” TONE Treble 2 VOL. 0.0dB L SL SW C R SR Press PROGRAM l / h to adjust the output level in those frequency ranges. - You can set the tone control for speakers and headphones separately. Connect the headphones when adjusting the headphone tone control. - If you set an extreme tone balance, sounds may not match those from other channels. ©2010 Yamaha Corporation -8- YC504B0/QREN