Simplicity 10L802-0001-F1 Handleiding

Merk: Simplicity

Model: 10L802-0001-F1

Type: Handleiding

Deze handleiding is ook geschikt voor

300 450 475 500 550 SERIES

Pokyny na obsluhu a údržbu

Slovenèina

Priroènik za uporabo

Slovenija

Form No. 277038VIK

Revision: M

Sprintt 500 Seriest

Quattrot 500 Seriest

LX 500 Seriest

500 Seriest

Qt 500/550 Seriest

300 Seriest

Classict 450 Seriest

Sprintt 475 Seriest

Quattrot 475 Seriest

Model 90000 Model 100000

Operator’s Manual

English

Dansk

ÅëëçíéêÜ

Español

Suomi

Français

Italiano

Norsk

Betjeningsvejledning

Bedienungsanleitung

Åã÷åéñßäéï ×ñÞóçò

Áúëãàðñêè

Manual del Operario

Käyttäjän käsikirja

Manuel de l’opérateur

Manuale dell’Operatore

Gebruiksaanwijzing

Brukerhåndbok

Manual do Operador

Instruktionsbok

Português

Svenska

Nederlands

Èíñòðóêöèè çà åêñïëîàòàöèÿ

Kasutusjuhend

Priruènik za operatora

Kezelési útmutató

Naudojimo instrukcija

Operatora rokasgrāmata

Instrukcja obs³ugi

Manual de utilizare

Ðóêîâîäñòâî ïî ýêñïëóàòàöèè

Kullanma Kýlavuzu

Eesti keel

Polski

Hrvatski

Magyar

Lietuvių

Deutsch

Latviešu

Românã

Ðóññêèé

Türkçe

Uputstvo za korisnike

Návod k obsluze

²íñòðóêö³¿ ç åêñïëóàòàö³¿

Srpski

Èeština

Óêðà¿íñüêà

Briggs & Stratton is a registered trademark

of Briggs & Stratton Corporation.

Not for

Reproduction

BRIGGSandSTRATTON.COM

Not for

Reproduction

5 6

1312

Not for

Reproduction

4 BRIGGSandSTRATTON.COM

General Information

This manual contains safety information to make you aware of the hazards and risks

associated with engines and how to avoid them. It also contains instructions for the

proper use and care of the engine. Because Briggs & Stratton Corporation does not

necessarily know what equipment this engine will power, it is important that you read and

understand these instructions and the instructions for the equipment. Save these

original instructions for future reference.

For replacement parts or technical assistance, record below the engine model, type, and

code numbers along with the date of purchase. These numbers are located on your

engine (see the Features and Controls page).

Date of purchase:

Engine model:

MM/DD/YYYY

Model: Code:Type:

Power Ratings: The gross power rating for individual gasoline engine models is labeled

in accordance with SAE (Society of Automotive Engineers) code J1940 Small Engine

Power & Torque Rating Procedure, and is rated in accordance with SAE J1995. Torque

values are derived at 2600 RPM for those engines with “rpm” called out on the label and

3060 RPM for all others; horsepower values are derived at 3600 RPM. The gross power

curves can be viewed at www.BRIGGSandSTRATTON.COM. Net power values are

taken with exhaust and air cleaner installed whereas gross power values are collected

without these attachments. Actual gross engine power will be higher than net engine

power and is affected by, among other things, ambient operating conditions and

engine--to--engine variability. Given the wide array of products on which engines are

placed, the gasoline engine may not develop the rated gross power when used in a given

piece of power equipment. This difference is due to a variety of factors including, but not

limited to, the variety of engine components (air cleaner, exhaust, charging, cooling,

carburetor, fuel pump, etc.), application limitations, ambient operating conditions

(temperature, humidity, altitude), and engine--to--engine variability. Due to manufacturing

and capacity limitations, Briggs & Stratton may substitute an engine of higher rated

power for this engine.

Operator Safety

Explosion

Toxic Fumes

Moving Parts

Shock

Hot Surface

Kickback

Fire

Fuel Shutoff

Read Manual

Choke

Oil

Fuel

On Off

Stop

Wear Eye

Protection

Slow

Fast

SAFETY AND CONTROL SYMBOLS

Hazardous

Chemical

Frostbite

The safety alert symbol is used to identify safety information about hazards that can

result in personal injury. A signal word (DANGER, WARNING, or CAUTION) is used with the

alert symbol to indicate the likelihood and the potential severity of injury. In addition, a hazard

symbol may be used to represent the type of hazard.

DANGER indicates a hazard which, if not avoided, will result in death or

serious injury.

WARNING indicates a hazard which, if not avoided, could result in death or

serious injury.

CAUTION indicates a hazard which, if not avoided, could result in minor or

moderate injury.

NOTICE indicates a situation that could result in damage to the product.

WARNING

Certain components in this product and its related accessories contain chemicals

known to the State of California to cause cancer, birth defects, or other reproductive

harm. Wash hands after handling.

WARNING

The engine exhaust from this product contains chemicals k nown to the State of

California to cause cancer, birth defects, or other reproductive harm.

WARNING

Briggs & Stratton Engines are not designed for and are not to be used to power:

fun-karts; go-karts; children’s, recreational, or sport all-terrain vehicles (ATVs);

motorbikes; hovercraft; aircraft products; or vehicles used in competitive events not

sanctioned by Briggs & Stratton. For information about competitive racing products,

see www.briggsracing.com. For use with utility and side-by-side ATVs, please contact

Briggs & Stratton Engine Application Center, 1-866-927-3349. Improper engine

application may result in serious injury or death.

NOTICE: This engine was shipped from Briggs & Stratton without oil. Before you start

the engine, make sure you add oil according to the instructions in this manual. If you

start the engine without oil, it will be damaged beyond repair and will not be covered

under warranty.

Not for

Reproduction

WARNING

Fuel and its vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

When Adding Fuel

 Turn engine off and let engine cool at least 2 minutes before removing the fuel

cap.

 Fill fuel tank outdoors or in well -ventilated area.

 Do not overfill fuel tank. To allow for expansion of the fuel, do not fill above the

bottom of the fuel tank neck.

 Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition

sources.

 Check fuel lines, tank, cap, and fittings frequently for cracks or leaks.

Replace if necessary

 If fuel spills, wait until it evaporates before starting engine.

When Starting Engine

 Ensure that spark plug, muffler, fuel cap and air cleaner (if equipped) are in

place and secured.

 Do not crank engine with spark plug removed.

 If engine floods, set choke (if equipped) to OPEN/RUN position, move throttle

(if equipped) to FAST position and crank until engine starts.

When Operating Equipment

 Do not tip engine or equipment at angle which causes fuel to spill.

 Do not choke the carburetor to stop engine.

 Never start or run the engine with the air cleaner assembly (if equipped) or the

air filter (if equipped) removed.

When Changing Oil

 When you drain the oil from the top oil fill tube, the fuel tank must be empty or

fuel can leak out and result in a fire or explosion.

When Tipping Unit for Maintenance

 When performing maintenance that requires the unit to be tipped, the fuel tank

must be empty or fuel can leak out and result in a fire or explosion.

When Transporting Equipment

 Transport with fuel tank EMPTY or with fuel shut-off valve OFF.

When Storing Fuel Or Equipment With Fuel In Tank

 Store away from furnaces, stoves, water heaters or other appliances that have

pilot lights or other ignition sources because they can ignite fuel vapors.

Starting engine creates sparking.

Sparking can ignite nearby flammable gases.

Explosion and fire could result.

WARNING

 If there is natural or LP gas leakage in area, do not start engine.

 Do not use pressurized starting fluids because vapors are flammable.

POISONOUS GAS HAZARD. Engine exhaust contains carbon

monoxide, a poisonous gas that could kill you in minutes. You

CANNOT see it, smell it, or taste it. Even if you do not smell exhaust

fumes, you could still be exposed to carbon monoxide gas. If you start

to feel sick, dizzy, or weak while using this product, shut it off and get

to fresh air RIGHT AWAY. See a doctor. You may have carbon

monoxide poisoning.

WARNING

 Operate this product ONLY outside far away from windows, doors and vents to

reduce the risk of carbon monoxide gas from accumulating and potentially being

drawn towards occupied spaces.

 Install battery--operated carbon monoxide alarms or plug--in carbon monoxide

alarms with battery back-up according to the manufacturer’s instructions.

Smoke alarms cannot detect carbon monoxide gas.

 DO NOT run this product inside homes, garages, basements, crawlspaces,

sheds, or other partially-enclosed spaces even if using fans or opening doors

and windows for ventilation. Carbon monoxide can quickly build up in these

spaces and can linger for hours, even after this product has shut off.

 ALWAYS place this product downwind and point the engine exhaust away from

occupied spaces.

Rapid r etraction of starter cord (kickback) will pull hand and arm

toward engine faster than you can let go.

Broken bones, fractures, bruises or sprains could result.

WARNING

 When starting engine, pull the starter cord slowly until resistance is felt and then

pull rapidly to avoid kickback.

 Remove all external equipment/engine loads before starting engine.

 Direct-coupled equipment components such as, but not limited to, blades,

impellers, pulleys, sprockets, etc., must be securely attached.

Rotating parts can contact or entangle hands, feet, hair, clothing, or

accessories.

Traumatic amputation or severe laceration can result.

WARNING

 Operate equipment with guards in place.

 Keep hands and feet away from rotating parts.

 Tie up long hair and remove jewelry.

 Do not wear loose-fitting clothing, dangling drawstrings or items that could

become caught.

Running engines produce heat. Engine parts, especially muffler,

become extremely hot.

Severe thermal burns can occur on contact.

Combustible debris, such as leaves, grass, brush, etc. can catch fire.

WARNING

 Allow muffler, engine cylinder and fins to cool before touching.

 Remove accumulated debris from muffler area and cylinder area.

 It is a v iolation of California Public Resource Code, Section 4442, to use or

operate the engine on any forest -covered, brush-covered, or grass-covered land

unless the exhaust system is equipped with a spark arrester, as defined in

Section 4442, maintained in effective working order. Other states or federal

jurisdictions may have similar laws. Contact the original equipment

manufacturer, retailer, or dealer to obtain a spark arrester designed for the

exhaust system installed on this engine.

Unintentional sparking can result in fire or electric shock.

Unintentional start-up can result in entanglement, traumatic

amputation, or laceration.

Fire hazard

WARNING

Before performing adjustments or repairs:

 Disconnect the spark plug wire and keep it away from the spark plug.

 Disconnect battery at negative terminal (only engines with electric start.)

 Use only correct tools.

 Do not tamper with governor spring, links or other parts to increase engine

speed.

 Replacement parts must be of the same design and installed in the same

position as the original parts. Other parts may not perform as well, may damage

the unit, and may result in injury.

 Do not strike the flywheel with a hammer or hard object because the flywheel

may later shatter during operation.

When testing for spark:

 Use approved spark plug tester.

 Do not check for spark with spark plug removed.

Not for

Reproduction

6 BRIGGSandSTRATTON.COM

Features and Controls

Compare the illustration

with your engine to familiarize yourself with the location of

various features and controls.

A. Engine Identification

Model Type Code

B. Spark Plug

C. Primer

D. Fuel Tank and Cap

E. Air Cleaner

F. Starter Cord Handle

G. Dipstick

H. Muffler

Muffler Guard (if equipped)

Spark Arrester (if equipped)

I. Throttle Control (if equipped)

Operation

Oil capacity (see the Specifications section)

Oil Recommendations

We recommend the use of Briggs & Stratton Warranty Certified oils for best

performance. Other high-quality detergent oils are acceptable if classified for service SF,

SG, SH, SJ or higher. Do not use special additives.

Outdoor temperatures determine the proper oil viscosity for the engine. Use the chart to

select the best viscosity for the outdoor temperature range expected.

* Below 40°F(4°C) the use of SAE 30 will result in hard starting.

** Above 80°F(27°C) the use of 10W-30 may cause increased oil consumption. Check

oil level more frequently.

How To Check/Add Oil - Figure

2 3

Before adding or checking the oil

 Place engine level.

 Clean the oil fill area of any debris.

1. Remove the dipstick (G) and wipe with a clean cloth (Figure 2, Figure 3).

2. Insert and tighten the dipstick.

3. Remove the dipstick and check the oil level. It should be at the top of the full indicator

(J) on the dipstick.

4. If low, add oil slowly into the engine oil fill (H). Do not overfill. After adding oil, wait

one minute and then recheck the oil level.

5. Replace and tighten the dipstick.

Low Oil Protection System (if equipped)

Some engines are equipped with a low oil sensor. If the oil is low, the sensor will either

activate a warning light or stop the engine. Stop the engine and follow these steps before

restarting the engine.

 Make sure the engine is level.

 Check the oil level. See the How To Check/Add Oil section.

 If the oil level is low, add the proper amount of oil. Start the engine and make sure

the warning light (if equipped) is not activated.

 If the oil level is not low, do not start the engine. Contact an Authorized Briggs &

Stratton Dealer to have the the oil problem corrected.

Fuel Recommendations

Fuel must meet these requirements:

 Clean, fresh, unleaded gasoline.

 A minimum of 87 octane/87 AKI (91 RON). High altitude use, see below.

 Gasoline with up to 10% ethanol (gasohol) is acceptable.

CAUTION: Do not use unapproved gasolines, such as E15 and E85. Do not mix oil in

gasoline or modify the engine to run on alternate fuels. Use of unapproved fuels will

damage the engine components and void the engine warranty.

To protect the fuel system from gum formation, mix a fuel stabilizer into the fuel. See

Storage. All fuel is not the same. If starting or performance problems occur, change fuel

providers or change brands. This engine is certified to operate on gasoline. The

emissions control system for this engine is EM (Engine Modifications).

High Altitude

At altitudes over 5,000 feet (1524 meters), a minimum 85 octane/85 AKI (89 RON)

gasoline is acceptable. To remain emissions compliant, high altitude adjustment is

required. Operation without this adjustment will cause decreased performance,

increased fuel consumption, and increased emissions. See an authorized Briggs &

Stratton Dealer for high altitude adjustment information.

Operation of the engine at altitudes below 2,500 feet (762 meters) with the high altitude

kit is not recommended.

How To Add Fuel - Figure

WARNING

Fuel and its vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

When Adding Fuel

 Turn engine off and let engine cool at least 2 minutes before removing the fuel

cap.

 Fill fuel tank outdoors or in well -ventilated area.

 Do not overfill fuel tank. To allow for expansion of the fuel, do not fill above the

bottom of the fuel tank neck.

 Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition

sources.

 Check fuel lines, tank, cap, and fittings frequently for cracks or leaks.

Replace if necessary

 If fuel spills, wait until it evaporates before starting engine.

1. Clean the fuel cap area of dirt and debris. Remove the fuel cap (A, Figure 4).

2. Fill the fuel tank (B) with fuel. To allow for expansion of the fuel, do not fill above the

bottom of the fuel tank neck (C).

3. Reinstall the fuel cap.

How To Start The Engine - Figure

5 6

Rapid r etraction of starter cord (kickback) will pull hand and arm

toward engine faster than you can let go.

Broken bones, fractures, bruises or sprains could result.

WARNING

 When starting engine, pull the starter cord slowly until resistance is felt and then

pull rapidly to avoid kickback.

WARNING

Fuel and its vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

When Starting Engine

 Ensure that spark plug, muffler, fuel cap and air cleaner (if equipped) are in

place and secured.

 Do not crank engine with spark plug removed.

 If engine floods, set choke (if equipped) to OPEN/RUN position, move throttle

(if equipped) to FAST position and crank until engine starts.

Not for

Reproduction

POISONOUS GAS HAZARD. Engine exhaust contains carbon

monoxide, a poisonous gas that could kill you in minutes. You

CANNOT smell it, or taste it. Even if you do not smell exhaust fumes,

you could still be exposed to carbon monoxide gas. If you start to feel

sick, dizzy, or weak while using this product, shut it off and get to fresh

air RIGHT AWAY. See a doctor. You may have carbon monoxide

poisoning.

WARNING

 Operate this product ONLY outside far away from windows, doors and vents to

reduce the risk of carbon monoxide gas from accumulating and potentially being

drawn towards occupied spaces.

 Install battery--operated carbon monoxide alarms or plug--in carbon monoxide

alarms with battery back-up according to the manufacturer’s instructions.

Smoke alarms cannot detect carbon monoxide gas.

 DO NOT run this product inside homes, garages, basements, crawlspaces,

sheds, or other partially-enclosed spaces even if using fans or opening doors

and windows for ventilation. Carbon monoxide can quickly build up in these

spaces and can linger for hours, even after this product has shut off.



ALWAYS place this product downwind and point the engine exhaust

away from occupied spaces.

NOTICE: This engine was shipped from Briggs & Stratton without oil. Before you start

the engine, make sure you add oil according to the instructions in this manual. If you

start the engine without oil, it will be damaged beyond repair and will not be covered

under warranty.

Note: Equipment may have remote controls. See the equipment manual for location and

operation of remote controls.

1. Check the engine oil. See the How To Check/Add Oil section.

2. Make sure equipment drive controls, if equipped, are disengaged.

3. Move the throttle control (A, Figure 5), if equipped, to the fast

position.

Operate the engine in the fast

position.

4. When starting a new engine for the first time, firmly push the red primer (B)five

times. Then for all future starts, push the primer three times (Figure 5).

Note: If engine runs out of fuel or has been stored for an extended period of time, it

may be necessary to prime 5 times.

Note: Priming is usually unnecessary when restarting a warm engine.

Note: If you push the primer too many times, excessive fuel will flood the engine and

it will be difficult to start.

5. If the product is equipped with an engine stop lever (C), hold the engine stop lever

against the handle (Figure 6).

6. Firmly hold the starter cord handle (D). Pull the starter cord handle slowly until

resistance is f elt, then pull rapidly (Figure 5).

Note: If the engine does not start after repeated attempts, repeat Steps 4, 5, and 6. If

it still does not start, go to BRIGGSandSTRATTON.COM or call 1-800-233-3723 (in

USA).

WARNING: Rapid retraction of the starter cord (kickback) will pull your

hand and arm toward the engine faster than you can let go. Broken bones, fractures,

bruises or sprains could result. When starting engine, pull the starter cord slowly until

resistance is felt and then pull rapidly to avoid kickback.

How To Stop The Engine - Figure

Release the engine stop lever (E). SeeFigure6.

Engine with Throttle Control: Move the throttle c ontrol (A, Figure 5) to the stop

position.

Maintenance

NOTICE: If the engine is tipped during maintenance, the fuel tank must be empty and

thesparkplugsidemust be up. If the fuel tank is not empty and if the engine is tipped in

any other direction, it may be difficult to start due to oil or gasoline contaminating the air

filter and/or the spark plug.

WARNING: When performing maintenance that requires the unit to be

tipped, the fuel tank must be empty or fuel can leak out and result in a fire or

explosion.

We recommend that you see any Briggs & Stratton Authorized Dealer for all

maintenance and service of the engine and engine parts.

NOTICE: All the components used t o build this engine must remain in place for proper

operation.

Emissions Control

Maintenance, replacement, or repair of the emissions control devices and systems

may be performed by any non- road engine repair establishment or individual.

However, to obtain “no charge” emissions control service, the work must be performed

by a factory authorized dealer. See the Emissions Warranty.

Unintentional sparking can result in fire or electric shock.

Unintentional start-up can result in entanglement, traumatic

amputation, or laceration.

Fire hazard

WARNING

Before performing adjustments or repairs:

 Disconnect the spark plug wire and keep it away from the spark plug.

 Disconnect battery at negative terminal (only engines with electric start.)

 Use only correct tools.

 Do not tamper with governor spring, links or other parts to increase engine

speed.

 Replacement parts must be of the same design and installed in the same

position as the original parts. Other parts may not perform as well, may damage

the unit, and may result in injury.

 Do not strike the flywheel with a hammer or hard object because the flywheel

may later shatter during operation.

When testing for spark:

 Use approved spark plug tester.

 Do not check for spark with spark plug removed.

Not for

Reproduction

BRIGGSandSTRATTON.COM

Maintenance Chart

First 5 Hours

 Change Oil

Every8HoursorDaily

 Check engine oil level

 Clean area around muffler and controls

Every 25 Hours or Annually

 Clean air f ilter *

Every 50 Hours or Annually

 Change engine oil

 Check muffler and spark arrester

Annually

 Replace air filter

 Replace spark plug

 Clean air cooling system *

* In dusty conditions or when airborne debris is present, clean more often.

Carburetor And Engine Speed Adjustment

Never make adjustments to the carburetor or engine speed. The carburetor was set at

the factory to operate efficiently under most conditions. Do not tamper with the governor

spring, linkages, or other parts to change the engine speed. If any adjustments are

required contact a Briggs & Stratton Authorized Service Center for service.

NOTICE: The equipment manufacturer specifies the maximum speed for the engine as

installed on the equipment. Do not exceed this speed. If you are unsure what the

equipment maximum speed is, or what the engine speed is set to from the factory,

contact a Briggs & Stratton Authorized Service Center for assistance. For safe and

proper operation of the equipment, the engine speed should be adjusted only by a

qualified service technician.

How To Replace The Spark Plug - Figure

Check the gap (A, Figure 7) with a wire gauge (B). If necessary, reset the gap. Install

and tighten the spark plug to the recommended torque. For gap setting or torque, see the

Specifications section.

Note: In some areas, local law requires using a resistor spark plug to suppress ignition

signals. If this engine was originally equipped with a resistor spark plug, use the same

type for replacement.

Inspect Muffler And Spark Arrester - Figure

Running engines produce heat. Engine parts, especially muffler,

become extremely hot.

Severe thermal burns can occur on contact.

Combustible debris, such as leaves, grass, brush, etc. can catch fire.

WARNING

 Allow muffler, engine cylinder and fins to cool before touching.

 Remove accumulated debris from muffler area and cylinder area.

 It is a v iolation of California Public Resource Code, Section 4442, to use or

operate the engine on any forest -covered, brush-covered, or grass-covered land

unless the exhaust system is equipped with a spark arrester, as defined in

Section 4442, maintained in effective working order. Other states or federal

jurisdictions may have similar laws. Contact the original equipment

manufacturer, retailer, or dealer to obtain a s park arrester designed for the

exhaust system installed on this engine.

Remove accumulated debris from muffler area and cylinder area. Inspect the muffler (A)

for cracks, corrosion, or other damage. Remove the spark arrester (B), if equipped, and

inspect for damage or carbon blockage. If damage is found, install replacement parts

before operating.

WARNING: Replacement parts must be of the same design and installed

in the same position as the original parts. Other parts may not perform as well, may

damage the unit, and may result in injury.

How To Change The Oil - Figure

2 3 9 10

WARNING

Fuel and its vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

 When you drain the oil from the top oil fill tube, the fuel tank must be empty or

fuel can leak out and result in a fire or explosion.

Used oil is a hazardous waste product and must be disposed of properly. Do not discard

with household waste. Check with your local authorities, service center, or dealer for safe

disposal/ recycling facilities.

Remove Oil

The oil must be drained from the top oil fill tube (E, Figure 10).

1. With engine off but still warm, disconnect the spark plug wire (A) and keep it away

from the spark plug (Figure 9).

2. Remove the dipstick (G, Figure 2).

3. When you drain the oil from the top oil fill tube (E), keep the spark plug end of the

engine (F) up (Figure 10). Drain the oil into an approved container.

WARNING: When you drain the oil from the top oil fill tube, the fuel tank

must be empty or fuel can leak out and result in a fire or explosion. To empty the fuel

tank, run the engine until it stops from lack of fuel.

Add Oil

 Place engine level.

 Clean the oil fill area of any debris.

 See the Specifications section for oil capacity.

1. Remove the dipstick (G) and wipe with a clean cloth (Figure 2, Figure 3).

2. Pour the oil slowly into the engine oil fill (H). Do not overfill. After adding oil, wait

one minute and then check the oil level.

3. Install and tighten the dipstick.

4. Remove the dipstick and check the oil level. It should be at the top of the full indicator

(J) on the dipstick.

5. Install and tighten the dipstick.

How To Service The Air Filter - Figure

11 12

WARNING

Fuel and its vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

 Never start or run the engine with the air cleaner assembly (if equipped) or the

air filter (if equipped) removed.

NOTICE: Do not use pressurized air or solvents to clean the filter. Pressurized air can

damage the filter and solvents will dissolve the filter.

Two types of air filter systems are shown, a Standard and a High Capacity. Determine

the type installed on your engine and service as follows.

Standard Air Filter - Figure

The standard air filter uses a foam element that can be washed and reused.

1. Remove the screw (A) from the top of the air filter assembly (B). See Figure 11.

2. To prevent debris from falling into the carburetor, carefully remove the air filter

assembly.

3. Remove the foam element (C) from the air filter base.

4. Wash the foam element in liquid detergent and water. Squeeze dry the foam element

in a clean cloth.

5. Saturate the foam element with clean engine oil. To remove the excess engine oil,

squeeze the foam element in a clean cloth.

6. Install the foam element into the air filter base.

7. Install the air filter assembly onto the carburetor and secure with screw.

High Capacity Air Filter - Figure

The high capacity air filter uses a pleated filter.

1. Remove the screw (A) from the top of the air filter assembly (B). See Figure 12.

2. To prevent debris from falling into the carburetor, carefully remove the air filter

assembly.

3. Remove the pleated filter (C) from the air filter base.

4. To loosen debris, gently tap the pleated filter on a hard surface. If the pleated filter is

excessively dirty, replace with a new filter.

5. Install the pleated filter.

6. Install the air filter assembly onto the carburetor and secure with screw.

Not for

Reproduction

Clean Air Cooling System - Figure

Running engines produce heat. Engine parts, especially muffler,

become extremely hot.

Severe thermal burns can occur on contact.

Combustible debris, such as leaves, grass, brush, etc. can catch fire.

WARNING

 Allow muffler, engine cylinder and fins to cool before touching.

 Remove accumulated debris from muffler area and cylinder area.

NOTICE: Do not use water to clean the engine. Water could contaminate the fuel

system. Use a brush or dry cloth to clean the engine.

This is an air cooled engine. Dirt or debris can restrict air flow and cause the engine to

overheat, resulting in poor performance and reduced engine life.

Use a brush or dry cloth to remove debris from the finger guard (A). Keep linkage,

springs and controls ( B) clean. Keep the area around and behind the muffler (C)freeof

any combustible debris (Figure 13).

Storage

WARNING

Fuel and its vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

When Storing Fuel Or Equipment With Fuel In Tank

 Store away from furnaces, stoves, water heaters or other appliances that have

pilot lights or other ignition sources because they can ignite fuel vapors.

Fuel System

Fuel can become stale when stored over 30 days. Stale fuel causes acid and gum

deposits to form in the fuel system or on essential carburetor parts. To keep fuel fresh,

use Briggs & Stratton Advanced Formula Fuel Treatment & Stabilizer, available

wherever Briggs & Stratton genuine service parts are sold.

For engines equipped with a FRESH START

fuel cap, use Briggs & Stratton FRESH

START

available in a drip concentrate cartridge.

There is no need to drain gasoline from the engine if a fuel stabilizer is added according

to instructions. Run the engine for 2 minutes to circulate the stabilizer throughout the fuel

system before storage.

If gasoline in the engine has not been treated with a f uel stabilizer, it must be drained into

an approved container. Run the engine until it stops from lack of fuel. The use of a fuel

stabilizer in the storage container is recommended to maintain freshness.

Engine Oil

While the engine is still warm, change the engine oil.

NOTICE: Store the engine level (normal operating position). If the engine is tipped for

storage, the f uel tank must be empty and the spark plug side must be up. If the fuel

tank is not empty and if the engine is tipped in any other direction, it may be difficult to

start due to oil or gasoline contaminating the air filter and/or the spark plug.

Troubleshooting

Need Assistance? Go to BRIGGSandSTRATTON.COM or call 1-800-233-3723 in USA.

Specifications

Engine Specifications

Model 90000

Displacement 9.02 ci (148 cc)

Bore 2.562 in (65.08 mm)

Stroke 1.750 in (44.45 mm)

Oil Capacity 18 -- 20 oz (0.54 -- 0.59 L)

Engine Specifications

Model 100000

Displacement 9.67 ci (158 cc)

Bore 2.562 in (65.08 mm)

Stroke 1.875 in (47.65 mm)

Oil Capacity 18 -- 20 oz (0.54 -- 0.59 L)

Tune-up Specifications *

Model 90000, 100000

Spark Plug Gap 0.030 in (0.76 mm)

Spark Plug Torque 180 lb-in (20 Nm)

Armature Air Gap 0.006 - 0.010 in (0.15 - 0.25 mm)

Intake Valve Clearance 0.005 - 0.007 in (0.13 - 0.18 mm)

Exhaust Valve Clearance 0.007 - 0.009 in (0.18 - 0.23 mm)

* Engine power will decrease 3.5% for each 1,000 feet (300 meters) above sea level and

1% for each 10 F(5.6 C) above 77 F(25 C). The engine will operate satisfactorily at

an angle up to 15. Refer to the equipment operator’s manual for safe allowable

operating limits on slopes.

Common Service Parts n

Service Part Part Number

Standard Air Filter 698369

High Capacity Air Filter 797819

Oil -- SAE 30 100005

Fuel Additive 5041, 5058

Resistor Spark Plug 796112

Long Life Platinum Spark Plug 5062

Spark Plug Wrench 89838, 5023

Spark Tester 19368

n We recommend that you see any Briggs & Stratton Authorized Dealer for all

maintenance and service of the engine and engine parts.

Not for

Reproduction

10 BRIGGSandSTRATTON.COM

BRIGGS & STRATTON ENGINE WARRANTY POLICY

April 2013

Briggs & Stratton warrants that, during the warranty period specified below, it will repair or replace, free of charge, any part that is defective in material or workmanship or both.

Transportation charges on product submitted for repair or replacement under this warranty must be borne by purchaser. This warranty is effective for and is subject to the time

periods and conditions stated below. For warranty service, find the nearest Authorized Service Dealer in our dealer locator map at BRIGGSandSTRATTON.COM. The

purchaser must contact the Authorized Service Dealer, and then make the product available to the Authorized Service Dealer for inspection and testing.

There is no other express warranty. Implied warranties, including those of merchantability and fitness for a particular purpose, are limited to one year from

purchase, or to the extent permitted by law. All other implied warranties are excluded. Liability for incidental or consequential damages are excluded to the extent

exclusion is permitted by law. Some states or countries do not allow limitations on how long an implied warranty lasts, and some states or countries do not allow the exclusion

or limitation of incidental or consequential damages, so the above limitation and exclusion may not apply to you. This warranty gives you specific legal rights and you may also

have other rights which vary from state t o state and country to country **.

LIMITED WARRANTY

STANDARD WARRANTY TERMS *

Brand/Product Type Consumer Use Commercial Use

Vanguardt

3 years 3 years

Commercial Turf Seriest

2 years 2 years

Extended Life Seriest; I/C

; Intekt I/C

; Intekt Pro ;

Professional Seriest with Dura-Boret Cast Iron Sleeve;

850 Seriest with Dura -Boret Cast Iron Sleeve;

Snow Series MAXt with Dura-Boret Cast Iron Sleeve

All Other Briggs & Stratton Engines Featuring Dura-Boret Cast Iron Sleeve

2 years 1 year

All Other Briggs & Stratton Engines 2 years 90 days

* These are our standard warranty terms, but occasionally there may be additional warranty coverage that was not determined at time of publication. For a listing of current

warranty terms for your engine, go to BRIGGSandSTRATTON.COM or contact your Briggs & Stratton Authorized Service Dealer.

** In Australia -- Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund foramajor

failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of

acceptable quality and the failure does not amount to a major failure. For wa rranty service, find the nearest Authorized Service Dealer in our dealer locator map at

BRIGGSandSTRATTON.COM, or by calling 1300 274 447, or by emailing or writing to salesenquiries@briggsandstratton.com.au, Briggs & Stratton AustraliaPtyLtd,1

Moorebank Avenue, Moorebank, NSW , Australia, 2170.

Home Standby Generator applications: 2 years consumer warranty only. No commercial warranty. This warranty does not apply to engines on equipment used for prime

power in place of a utility. Engines used in competitive racing or on commercial or rental tracks are not warranted.

Vanguard installed on standby generators: 2 years consumer use, no warranty commercial use. Vanguard installed on utility vehicles: 2 years c onsumer use, 2 years

commercial use. Vanguard 3-cylinder liquid cooled: see Briggs & Stratton 3/LC Engine Warranty Policy.

The warranty period begins on the date of purchase by the first retail consumer or commercial end user, and continues for the period of time stated in the table above. “Consumer

use” means personal residential household use by a retail consumer. “Commercial use” means all other uses, including use for commercial, income producing or rental purposes.

Once an engine has experienced commercial use, it shall thereafter be considered as a commercial use engine for purposes of this warranty.

No warranty registration is necessary to obtain warranty on Briggs & Stratton products. Save your proof of purchase receipt. If you do not provide proof of the initial

purchase date at the time warranty service is requested, the manufacturing date of the product will be used to determine the warranty period.

About Your Warranty

Briggs & Stratton welcomes warranty repair and apologizes to you for being

inconvenienced. Any Authorized Service Dealer may perform warranty repairs. Most

warranty repairs are handled routinely, but sometimes requests for warranty service may

not be appropriate. To avoid misunderstanding which might occur between the customer

and the dealer, listed below are some of the causes of engine failure that the warranty

does not cover.

Normal wear: Engines, like all mechanical devices, need periodic parts service and

replacement to perform well. Warranty will not cover repair when normal use has

exhausted the life of a part or an engine. Warranty would not apply if engine damage

occurred because of misuse, lack of routine maintenance, shipping, handling,

warehousing or improper installation. Similarly, warranty is v oid if the serial number of the

engine has been removed or the engine has been altered or modified.

Improper maintenance: The life of an engine depends upon the conditions under which

it operates, and the care it receives. Some applications, such as tillers, pumps and rotary

mowers, are very often used in dusty or dirty conditions, which can cause what appears

to be premature wear. Such wear, when caused by dirt, dust, spark plug cleaning grit, or

other abrasive material that has entered the engine because of improper maintenance, is

not covered by warranty.

This warranty covers engine related defective material and/or workmanship only

and not replacement or refund of the equipment to which the engine may be

mounted. Nor does the warranty extend to repairs required because of:

1 Problems caused by parts that are not original Briggs & Stratton parts.

2 Equipment controls or installations that prevent starting, cause unsatisfactory engine

performance, or shorten engine life. (Contact equipment manufacturer.)

3 Leaking carburetors, clogged fuel pipes, sticking valves, or other damage, caused

by using contaminated or stale fuel.

4 Parts which are scored or broken because an engine was operated with insufficient

or contaminated lubricating oil, or an incorrect grade of lubricating oil (check and

refill when necessary, and change at recommended intervals). OIL GARD may not

shut down r unning engine. Engine damage may occur if oil level is not properly

maintained.

5 Repair or adjustment of associated parts or assemblies such as clutches,

transmissions, remote controls, etc., which are not manufactured by Briggs &

Stratton.

6 Damage or wear to parts caused by dirt, which entered the engine because of

improper air c leaner maintenance, re-assembly, or use of a non-original air cleaner

element or cartridge. At recommended interv als, clean and/or replace the filter as

stated in the Operator’s Manual.

7 Parts damaged by over-speeding, or overheating caused by grass, debris, or dirt,

which plugs or clogs the cooling fins, or flywheel area, or damage caused by

operating the engine in a confined area without sufficient ventilation. Clean engine

debris at recommended intervals as stated in the Operator’s Manual.

8 Engine or equipment parts broken by excessive vibration caused by a loose engine

mounting, loose cutter blades, unbalanced blades or loose or unbalanced impellers,

improper attachment of equipment to engine crankshaft, over-speeding or other

abuse in operation.

9 A bent or broken crankshaft, caused by stri king a solid object with the cutter blade of

a rotary lawn mower, or excessive v-belt tightness.

10 Routine tune-up or adjustment of the engine.

11 Engine or engine component failure, i.e., combustion chamber, valves, valve seats,

valve guides, or burned starter motor windings, caused by the use of alternate fuels

such as, liquified petroleum, natural gas, gasoline formulated with ethanol greater

than 10%, etc.

W arranty service is available only through Briggs & Stratton Authorized Service

Dealers. Locate your nearest Authorized Service Dealer in our dealer locator map

on BRIGGSandSTRATT ON.CO M or by calling 1-800-233-3723 (in USA).

Not for

Reproduction

California, U.S. EPA, and Briggs & Stratton Corporation Emissions Control Warranty Statement

Your Warranty Rights And Obligations

April 2013

The California Air Resources Board, U.S. EPA, and Briggs & Stratton (B&S) are pleased

to explain the emissions control system warranty on your Model Year 2013--2014

engine/equipment. In California, new small off-road engines and large spark ignited

engines less than or equal to 1.0 liter must be designed, built, and equipped to meet the

State’s stringent anti-smog standards. B&S must warrant the emissions control system

on your engine/equipment for the periods of time listed below provided there has been

no abuse, neglect, or improper maintenance of your engine/equipment.

Your exhaust emissions control system may include parts such as the carburetor or fuel

injection system, ignition system, and catalytic converter. Also included may be hoses,

belts, connectors, sensors, and other emissions-related assemblies. Your evaporative

emission control system may include parts such as: carburetors, fuel tanks, fuel lines,

fuel caps, valves, canisters, filters, vapor hoses, clamps, connectors, and other

associated components.

Where a warrantable condition exists, B&S will repair your engine/equipment at no cost

to you including diagnosis, parts, and labor.

Manufacturer’s Warranty Coverage:

Small off-road engines and large spark ignited engines less than or equal to 1.0 liter, and

any related emissions components of the equipment, are warranted for two years*. If any

emissions-related part on your B&S engine/equipment is defective, the part will be

repaired or replaced by B&S.

* Two years or for the time period listed in the respective engine or product warranty

statement, whichever is greater.

Owner’s Warranty Responsibilities:

 As the engine/equipment owner, you are responsible for the performance of the

required maintenance listed in your owner’s manual. B&S recommends that you

retain all receipts covering maintenance on your engine/equipment, but B&S cannot

deny warranty solely for the lack of receipts or your failure to ensure the performance

of all scheduled maintenance.

 As the engine/equipment owner, you should however be aware that B&S may deny

you warranty coverage if your engine/equipment or a part has failed due to abuse,

neglect, improper maintenance, or unapproved modifications.

 You are responsible for presenting your engine/equipment to a B&S distribution

center, servicing dealer, or other equivalent entity, as applicable, as soon as a

problem exists. The warranty repairs should be completed in a reasonable amount of

time, not to exceed 30 days. If you have any questions regarding your warranty

rights and responsibilities, you should contact B&S at 1--800--444--7774 (in USA) or

BRIGGSandSTRATTON.COM.

Briggs & Stratton Emissions Control Warranty Provisions

The following are specific provisions relative to your Emissions Control Warranty Coverage. It is in addition to the B&S engine warranty for non-regulated engines found in the

Operator’s Manual.

1. Warranted Emissions Parts

Coverage under this warranty extends only to the parts listed below (the emissions

control systems parts) to the extent these parts were present on the B&S engine

and/or B&S supplied fuel system.

a. Fuel Metering System

 Cold start enrichment system (soft choke)

 Carburetor and internal parts

 Fuel pump

 Fuel line, fuel line fittings, clamps

 Fuel tank, cap and tether

 Carbon canister

b. Air Induction System

 Air cleaner

 Intake manifold

 Purge and vent line

c. Ignition System

 Spark plug(s)

 Magneto ignition system

d. Catalyst System

 Catalytic converter

 Exhaust manifold

 Air injection system or pulse valve

e. Miscellaneous Items Used in Above Systems

 Vacuum, temperature, position, time sensitive v alves and switches

 Connectors and assemblies

2. Length of Coverage

For a period of two years from date of original purchase*, B&S warrants to the

original purchaser and each subsequent purchaser that the engine is designed, built,

and equipped so as to conform with all applicable regulations adopted by the Air

Resources Board; that it is free from defects in material and workmanship that could

cause the failure of a warranted part; and that it is identical in all material respects to

the engine described in the manufacturer’s application for certification. The warranty

period begins on the date the engine is originally purchased.

* Two years or for the time period listed in the respective engine or product

warranty statement, whichever is greater.

The warranty on emissions-related parts is as follows:

 Any warranted part that is not scheduled for replacement as required

maintenance in the owner’s manual supplied, is warranted for the warranty

period stated above. If any such part fails during the period of warranty

coverage, the part will be repaired or replaced by B&S at no charge to the

owner. Any such part repaired or replaced under the warranty will be warranted

for the remaining warranty period.

 Any warranted part that is scheduled only for regular inspection in the owner’s

manual supplied, is warranted for the warranty period stated above. Any such

part repaired or replaced under warranty will be warranted for the remaining

warranty period.

 Any warranted part that is scheduled for replacement as required maintenance

in the owner’s manual supplied, is warranted for the period of time prior to the

first scheduled replacement point for that part. If the part fails prior to the first

scheduled replacement, the part will be repaired or replaced by B&S at no

charge to the owner. Any such part repaired or replaced under warranty will be

warranted for the remainder of the period prior to the first scheduled

replacement point for the part.

 Add on or modified parts that are not exempted by the Air Resources Board

may not be used. The use of any non exempted add on or modified parts by the

owner will be grounds for disallowing a warranty claim. The manufacturer will

not be liable to warrant failures of warranted parts caused by the use of a non

exempted add on or modified part.

3. Consequential Coverage

Coverage shall extend to the failure of any engine components caused by the

failure of any warranted emissions parts.

4. Claims and Coverage Exclusions

Warranty claims shall be filed according to the provisions of the B&S engine

warranty policy. Warranty coverage does not apply to failures of emissions parts

that are not original equipment B&S parts or to parts that fail due to abuse, neglect,

or improper maintenance as set forth in the B&S engine warranty policy. B&S is not

liable for warranty coverage of failures of emissions parts caused by the use of

add-on or modified parts.

Look For Relevant Emissions Durability Period and Air Index Information

On Your Small Off-Road Engine Emissions Label

Engines that are certified to meet the California Air Resources Board (CARB) small

off-road Emissions Standard must display information regarding the Emissions Durability

Period and the Air Index. Briggs & Stratton makes this information available to the

consumer on our emissions labels. The engine emissions label will indicate certification

information.

The Emissions Durability Period describes the number of hours of actual running time

for which the engine is certified to be emissions compliant, assuming proper

maintenance in accordance with the Operating & Maintenance Instructions. The

following categories are used:

Moderate:

Engine is certified to be emissions compliant for 125 hours of actual engine running time.

Intermediate:

Engine is certified to be emissions compliant for 250 hours of actual engine running time.

Extended:

Engine is certified to be emissions compliant for 500 hours of actual engine running time.

For example, a typical walk-behind lawn mower is used 20 to 25 hours per year.

Therefore, the Emissions Durability Period of an engine with an intermediate rating

would equate to 10 to 12 years.

Briggs & Stratton engines are certified to meet the United States Environmental

Protection Agency (USEPA) Phase 2 or Phase 3 emissions standards. The Emissions

Compliance Period referred to on the Emissions Compliance label indicates the number

of operating hours for which the engine has been shown to meet Federal emissions

requirements.

For engines less than 225 cc displacement.

Category C = 125 hours, Category B = 250 hours, Category A = 500 hours

For engines of 225 cc or more displacement.

Category C = 250 hours, Category B = 500 hours, Category A = 1000 hours

Not for

Reproduction

12 BRIGGSandSTRATTON.COM

Generelle oplysninger

Denne manual indeholder sikkerhedsoplysninger, der skal gøre dig opmærksom på de

farer og risici, der er forbundet med motorer, samt hvordan de kan undgås. Den

indeholder ligeledes anvisninger for korrekt anvendelse og vedligeholdelse. Eftersom

Briggs & Stratton Corporation ikke nødvendigvis ved, hvilket udstyr denne motor skal

drive, er det vigtigt, at du læser og forstår denne vejledning og vejledningen til det udstyr,

som motoren driver. Gem disse originale anvisninger til fremtidig brug.

I forbindelse med reservedele eller teknisk assistance skal du nedenfor registrere

motormodel, type og kodenumre sammen med købsdatoen. Disse tal findes på din motor

(se siden Udstyr og betjeningselementer).

Købsdato:

Motormodel:

DD/MM/ÅÅÅÅ

Modelserie: Kode:Type:

Nominel effekt: Den nominelle bruttoeffekt for individuelle benzinmotormodeller er

mærket i overensstemmelse med den amerikanske organisation SAEs (Society of

Automotive Engineers) lovsamling J1940 (Small Engine Power & Torque Rating

Procedure), og effektydelsen er opnået og rettet til i overensstemmelse med SAE J1995.

Drejningsmomentet fås ved 2600 o/min. for motorer med ”o/min” (rpm) printet på

mærkaten, og 3060 o/min. for alle andre; hestekræfter fås ved 3600 o/min.

Bruttoeffektkurverne kan ses på www.BRIGGS andSTRATTON.COM. Nettoværdier

tages med monteret udstødning og installeret luftfilter, hvorimod bruttoværdier indhentes

uden dette tilbehør. Den faktiske bruttoeffekt vil v ære højere end nettoeffekten, og den vil

være påvirket af bl.a. omgivende arbejdsforhold og maskine-til-maskine-foranderlighed. I

betragtning af både den brede vifte af produkter, som motorerne er monteret på, udvikler

benzinmotoren muligvis ikke den nominelle bruttoeffekt, når den anvendes i et bestemt

effektudstyr. Denne forskel skyldes en række faktorer, der inkluderer, men som ikke er

begrænset til motorkomponenter (luftfiltre, udstødning, ladning, afkøling, karburator,

brændstofpumpe, mv.), anvendelsesbegrænsninger, omgivende arbejdsforhold

(temperatur, f ugt, højde) og maskine-til-maskine-foranderlighed. Grundet fabrikations- og

kapacitetsbegrænsninger, kan Briggs & Stratton erstatte en motor med en højere effekt

med denne motor.

erhed for operatoren

Brand Giftige dampeBevægelige dele Olie Langsom

StopHurtig Eksplosion Stød Brændstof

BrændstofhaneChoker On/Off-kontakt

Bær

beskyttelsesbriller

Varm overfladeLæs vejledningenFarligt kemikalie Forfrysninger

SIKKERHEDS- OG KONTROLSYMBOLER

Tilbageslag

Advarselssymbolet anvendes til at fremhæve sikkerhedsoplysninger om farer, der

kan medføre alvorlig personskade. Ordene FARE, ADVARSEL og FORSIGTIG anvendes

sammen med advarselssymbolet til at angive, hvor stor risikoen for skader er og omfanget

eller alvoren af sådanne personskader . Desuden anvendes et faresymbol til at angive den

relevante type fare.

FARE angiver en farlig situation, som vil medføre død eller alvorlig

personskade, hvis den ikke undgås.

ADVARSEL angiver en farlig situation, som kan medføre død eller alvorlig

personskade, hvis den ikke undgås.

FORSIGTIG angiver en farlig situation, som kan medføre mindre eller

moderat personskade, hvis den ikke undgås.

BEMÆRK angiver en situation, der kan resultere i beskadigelse af

produktet.

ADVARSEL

Visse komponenter i produktet og tilhørende udstyr indeholder kemikalier, der i følge

staten Californien forårsager cancer, medfødte misdannelser eller andre skader på

forplantningssystemet. Vask hænder efter håndtering.

ADVARSEL

I henhold til amerikansk lovgivning (Californien) gøres der opmærksom på, at

udstødningsgasserne fra denne maskine indeholder kræftfremkaldende stoffer.

Disse stoffer kan ligeledes medføre fosterskader og kan have en negativ effekt på

forplantningsevnen.

ADVARSEL

Briggs & Stratton-motorer er ikke udviklet til og må ikke bruges til kørsel af: fun-karts,

gokarts, børns køretøjer, fritidskøretøjer eller terrængående sportskøretøjer (ATV’er),

motorcykler, hovercrafts, luftfartøjsprodukter eller køretøjer, der bruges til

konkurrencer, s om ikke er godkendt af Briggs & Stratton. Yderligere information om

konkurrenceprægede racerprodukter findes på www.briggsracing.com. For brug med

tilbehør og side-by-side ATV’er bedes du kontakte Briggs & Stratton Engine

Application Center, 1-866-927-3349. Forkert maskinanvendelse kan resultere i

alvorlige kvæstelser eller død.

BEMÆRK: Denne motor blev afsendt fra Briggs & Stratton uden olie. Før du starter

motoren, sørg altid for at påfylde olie i henhold til de instruktioner angivet i denne

manual. Hvis du starter motoren uden påfyldning af olie, vil denne blive beskadiget og vil

ikke kunne repareres mere og derfor ikke være dækket af garantien.

Not for

Reproduction

ADVARSEL

Benzin og benzindampe er yderst brandfarlige og eksplosive.

Brand eller eksplosion kan medføre alvorlige forbrændinger eller

døden.

Påfyldning af brændstof

 Sluk for motoren, og lad motoren køle af i mindst 2 minutter, før tankdækslet

fjernes.

 Påfyld kun benzin udendørs eller på et sted med god udluftning.

 Undgå at fylde for meget brændstof på tanken. Undlad at fylde helt op til

kanten på påfyldningsstudsen, således at der er plads til, at benzinen kan

udvide sig.

 Benzin skal opbevares i sikker afstand fra gnister, åben ild, vågeblus, varme

og andre mulige antændelseskilder.

 Foretag hyppige eftersyn af brændstofslanger, tanken og tankdækslet samt

fittings for revner og utætheder. Udskift om nødvendigt.

 Hvis du spilder benzin, så vent med at starte motoren, indtil benzinen er

fordampet.

Startafmotoren

 Sørg for, at tændrøret, lyddæmperen, tankdækslet og luftfilteret (hvis monteret)

er på plads og forsvarligt fastgjort.

 Tørn ikke motoren, når tændrøret er afmonteret.

 Hvis motoren er druknet, sættes chokeren (hvis monteret) i

”OPEN/RUN”-position (kør) og gasspjældsr egulatoren i fast-position (hurtig),

hvorefter motoren tørnes, indtil den starter.

Betjening af redskabet

 Undgå at vippe motoren eller udstyret, således at benzinen løber ud.

 Tip ikke karburatoren til at standse motoren.

 Start aldrig motoren eller lad aldrig motoren køre med luftfilterenheden (hvis

monteret) eller luftfiltret (hvis monteret) fjernet.

Ved olieskift

 Hvis du tømmer olien fra oliepåfyldningsrøret i toppen, skal brændstoftanken

være tom, da brændstoffet ellers kan løbe ud og resultere i brand eller

eksplosion.

Ved vipning af en enheden ved vedligeholdelse

 Når der udføres vedligeholdelse, der kræver, at enheden vippes, skal

brændstoftanken være tom, da brændstoffet ellers kan løbe ud og resultere i

brand eller eksplosion.

Transport af redskabet

 Transport skal f oregå med TOM brændstoftank eller med brændstofhanen

LUKKET.

Opbevaring af brændstof og redskaber med brændstof i tanken

 Sørg for, at benzin og redskaber med brændstof i tanken opbevares i sikker

afstand fra fyr, ovne, vandvarmere og andre apparater, hvori der anvendes

vågeblus, samt andre antændelseskilder, da disse kan antænde

brændstofdampe.

Når motoren startes, dannes der gnister.

Gnister kan antænde brændbare gasarter, der befinder sig i

nærheden af motoren.

Dette kan medføre eksplosion og brand.

ADVARSEL

 Motoren må ikke startes, hvis der er naturgas eller flaskegas i nærheden.

 Der må ikke anvendes startvæske på dåse til at starte motoren, da dampene er

brændbare.

FARE FOR GIFTIG GAS. Motorens udstødningsgas indeholder kulilte,

en giftig gas, som kan slå en ihjel på få minutter. Du kan IKKE se den,

lugte den eller smage den. Du kan godt blive udsat for kulilte, selvom

du ikke kan lugte udstødningsgas. Hvis du begynder at føle dig dårlig

tilpas, svimmel eller svag under brug af dette produkt, skal du lukke for

det og sørge for at indånde frisk luft LIGE MED DET SAMME. Søg

lægehjælp. Du kan have kulilteforgiftning.

ADVARSEL

 Dette produkt må KUN betjenes udenfor langt fra vinduer, døre og

ventilationsanlæg for at reducere risikoen for at der samler sig kulilte, som kan

ledes til områder, hvor der befinder sig folk.

 Monter batteridrevne kuliltealarmer eller plug--in kuliltealarmer med

batteri-back-up i henhold til producentens anvisninger. Røgalarmer registrerer

ikke kuliltegas.

 Betjen IKKE dette produkt inden døre, i garager, k ældre, krybeområder, skure

eller andre delvist tillukkede områder, selv hvis der anvendes

ventilationsanordninger, eller hvis døre og vinduer er åbne for at foretage

gennemluftning. Der kan hurtigt samle sig kulilte i sådanne områder, som kan

blive hængende i flere timer, selv efter at produktet er blevet inaktiveret.

 Placer ALTID dette produkt i vindretningen, og lad motorens udstødning vende

væk fra områder, hvor der opholder sig folk.

Hurtig tilbagetrækning af startsnoren (tilbageslag) vil trække hånd og

arm tilbage mod motoren, hurtigere end du kan nå at slippe snoren.

Dette kan medføre, at du brækker armen, får knoglebrud, blå mærker

eller forstrækninger.

ADVARSEL

 Når motoren startes, træk langsomt i startsnoren, indtil du mærker modstand, og

træk derefter hurtigt for at undgå tilbageslag.

 Fjern alt eksternt udstyr/motorbelastninger før start af motoren.

 Direkte tilkoblede dele på udstyret f.eks. skæreknive, skovlhjul, remskiver,

kædehjul osv. skal være forsvarligt monteret.

Hænder, fødder, hår og tøj kan sætte sig fast i roterende dele.

Dette kan medføre, at legemsdele skæres af, eller at brugeren får

alvorlige snitsår.

ADVARSEL

 Udstyret må kun anvendes med alle sikkerhedsafskærmninger på plads.

 Hold hænder og fødder i sikker afstand fra roterende dele.

 Langt hår bør bindes op, og smykker og lignende genstande bør tages af.

 Undgå at bære løstsiddende tøj, tøj med snore eller andre genstande, der kan

sætte sig fast.

Kørende motorer udvikler varme. Motorens dele, især lyddæmperen,

bliver meget varme.

Kontakt med varme dele kan forårsage alvorlige forbrændinger.

Der kan gå ild i brændbart affald som f.eks. blade, græs og grene.

ADVARSEL

 Lyddæmper, cylinder og køleribber skal køle af, før du rører ved dem.

 Fjern snavs, der samler sig i området omkring lyddæmperen og cylinderen.

 Det er en overtrædelse af ”California Public Resource Code, Section 4442” at

bruge eller betjene motoren på skovdækkede, kratdækkede eller græsdækkede

områder med mindre, at udstødningssystemet er udstyret med en gnistfanger

som defineret i ”Section 4442”, der skal være i funktionel stand. Andre stater

eller føderale jurisdiktioner kan have lignende love. Kontakt den originale

udstyrsfabrikant, grossist eller forhandler for at købe en gnistfanger, der passer

til udstødningssystemet på motoren.

Gnister, som frembringes ved et uheld, kan medføre brand eller stød.

Hvis motoren startes ved et uheld, kan dette medføre, at personer

kommer i klemme i redskabets mekanismer, at legemsdele bliver

skåret af, eller at personer får snitsår.

Brandfare

ADVARSEL

Før justering eller reparation af motoren:

 Tag tændrørskablet af tændrøret, og hold det i sikker afstand fra tændrøret.

 Tag minuskablet af batteriet, hvis motoren er udstyret med el-starter.

 Brug kun korrekt værktøj.

 Foretag aldrig ændring af regulatorfjeder, regulatorforbindelser eller andre dele

for at øge motorens omdrejningstal.

 Udskiftningsdele skal være af samme design, og de skal monteres i samme

position som de originale dele. Andre reservedele fungerer muligvis ikke så

godt, kan evt. resultere i skader på enheden og kan måske resultere i

personskade.

 Slå aldrig på svinghjulet med en hammer eller en hård genstand, da dette kan få

svinghjulet til at splintres under drift.

Kontrol af gnist:

 Brug en godkendt gnisttester.

 Kontrollér ikke gnisten med tændrøret afmonteret.

Not for

Reproduction

14 BRIGGSandSTRATTON.COM

Udstyr og betjeningselementer

Sammenhold illustrationen

med din motor for at lære placeringen af udstyr og

betjeningselementer.

A. Identifikation af motoren

Model,- type,- og kodenummer

B. Tændrør

C. Justeringer

D. Brændstoftank og tankdæksel

E. Luftfilter

F. Startsnorgreb

G. Oliepind

H. Lyddæmper

Lyddæmperskærm (hvis monteret)

Gnistfanger (hvis monteret)

I. Gasregulator (hvis monteret)

Betjening

Oliekapacitet (se Specifikationer afsnittet)

Anbefalinger vedrørende olie

Vi anbefaler at bruge Briggs & Stratton Garanti-godkendte olier for den bedste ydelse.

Andre olier af høj kvalitet kan accepteres, såfremt disse hører under serviceklassificering

SF, SG, SH, SJ eller er af bedre kvaliteter. Anvend ikke specielle additiver.

Udendørs temperaturer bestemmer motorens rette olieviskositet. Brug skemaet til at

udvælge den bedste viskositet for de forventede udendørs temperaturintervaller.

SAE 30

10W-30

Syntetisk 5W-30

5W-30

°F °C

* Hvis en SAE 30 olie benyttes ved temperaturer under 40°F(4°C), vil det resultere i

startproblemer.

** Ved temperaturer over 80°F(27°C) vil brugen af 10W-30 medføre et olieforbrug, der

er højere end normalt. Kontrollér oliestanden hyppigere.

Kontrol/påfyldning af olie - Figur

2 3

Før påfyldning eller kontrol af olien

 Sørg for, at motoren er vandret.

 Rengør oliepåfyldningsområdet for eventuelt snavs.

1. Tag oliepinden (G) ud, og tør den af med en ren klud (figur 2, figur 3).

2. Sæt oliepinden tilbage, og spænd den fast.

3. Tag oliepinden ud, og kontrollér oliestanden. Kontrollér, at oliestanden er øverst på

mærket for fuld tank (J) på oliepinden.

4. Hvis oliestanden er lav, fyld langsomt olie ind i motorens oliepåfyldning (H). Overfyld

ikke. Efter oliepåfyldning skal du vente et minut og derefter kontrollere oliestanden

igen.

5. Udskift og fastspænd oliepinden.

Beskyttelsessystem for lav oliestand (hvis monteret)

Nogle motorer er udstyret med en føler for lav oliestand. Hvis oliestanden er for lav, vil

føleren tænde for en advarselslampe eller stoppe motoren. Stop motoren, og følg

nedenstående trin, inden motoren startes igen.

 Kontrollér, at motoren står plant.

 Kontrollér oliestanden. Se afsnittet Kontrol/påfyldning af olie.

 Hvis oliestanden er lav, efterfyldes den rette mængde olie. Start motoren, og

kontrollér at advarselslampen (hvis monteret) er aktiveret.

 Hvis oliestanden ikke er lav, må motoren ikke startes. Kontakt en autoriseret Briggs

& Stratton forhandler for at få afhjulpet oliestandsproblemet.

Anbefalinger vedr. brændstof

Benzinen skal leve op til disse krav:

 Ren, frisk, blyfri benzin.

 Oktantal på mindst 87/87 AKI (91 RON). Hvis motoren skal anvendes i

højtbeliggende områder, henvises til nedenstående.

 Benzin med op til 10 % etanol (gasohol) er acceptabelt.

FORSIGTIG: Der må ikke anvendes ikke-godkendt benzin, såsom E15 og E85. Der må

ikke blandes olie i benzinen, og motoren må ikke modificeres, så den kan køre med

alternative brændstoffer. Hvis der anvendes ikke-godkendt brændstof, vil motorens

komponenter blive beskadiget, og garantien på motoren bortfalder.

For at beskytte brændstofsystemet fra gummidannelse bland en brændstofstabilisator i

brændstoffet. Se afsnittet Opbevaring. Intet brændstof er ens. Hvis der opstår

problemer ved start eller ydelse, skift da brændstofleverandør eller skift

brændstofmærke. Denne motor er anerkendt til benzinbrug.

Emissionsreguleringssystemet for denne motor er EM (Engine Modifications) såkaldte

justeringer.

Anvendelse i højtbeliggende områder

Ved højder over 5,000 feet (1524 meters), kan der anvendes brændstof med et oktantal

på minimum 85 oktan/85 AKI (89 oktan). For at forblive certificeret til at opfylde

emissionskravene, skal der foretages justering til drift i højtbeliggende områder. Drift

uden denne justering vil resultere i nedsat ydelse, øget brændstofforbrug samt øget

emissionsniveau. Kontakt en autoriseret Briggs & Stratton forhandler vedrørende

information om justering til drift i højtbeliggende områder.

Betjening af motoren i højtbeliggende områder på under 2.500 fod (762 meter) med

sættet beregnet til anvendelse i højtbeliggende områder er ikke anbefalet.

Påfyldning af brændstof - Figur

ADVARSEL

Benzin og benzindampe er yderst brandfarlige og eksplosive.

Brand eller eksplosion kan medføre alvorlige forbrændinger eller

døden.

Påfyldning af brændstof

 Sluk for motoren, og lad motoren køle af i mindst 2 minutter, før tankdækslet

fjernes.

 Påfyld kun benzin udendørs eller på et sted med god udluftning.

 Undlad at fylde for meget brændstof i brændstoftanken. Undlad at fylde helt

op til kanten på påfyldningsstudsen, således at der er plads til at brændstoffet

kan udvide sig.

 Brændstof skal opbevares i sikker afstand fra gnister, åben ild, vågeblus,

varme og andre mulige antændelseskilder.

 Foretag hyppige eftersyn af brændstofslanger, tanken og tankdækslet samt

fittings for revner og utætheder. Udskift om nødvendigt.

 Hvis du spilder benzin, så vent med at starte motoren, indtil benzinen er

fordampet.

1. Rengør brændstofdækselområdet for snavs og rester. Fjern brændstofdækslet (A,

figur 4).

2. Fyld brændstoftanken (B) op med brændstof. Undlad at fylde helt op til kanten på

påfyldningsstudsen ( C), således at der er plads til at brændstoffet kan udvide sig.

3. Genmontér tankdækslet.

Startafmotoren-Figur

5 6

Hurtig tilbagetrækning af startsnoren (tilbageslag) vil trække hånd og

arm tilbage mod motoren, hurtigere end du kan nå at slippe snoren.

Dette kan medføre, at du brækker armen, får knoglebrud, blå mærker

eller forstrækninger.

ADVARSEL

 Når motoren startes, træk langsomt i startsnoren, indtil du mærker modstand, og

træk derefter hurtigt for at undgå tilbageslag.

ADVARSEL

Benzin og benzindampe er yderst brandfarlige og eksplosive.

Brand eller eksplosion kan medføre alvorlige forbrændinger eller

døden.

Startafmotoren

 Sørg for, at tændrøret, lyddæmperen, tankdækslet og luftfilteret (hvis monteret)

er på plads og forsvarligt fastgjort.

 Tørn ikke motoren, når tændrøret er afmonteret.

 Hvis motoren er druknet, sættes chokeren (hvis monteret) i

”OPEN/RUN”-position (kør) og gasspjældsr egulatoren i fast-position (hurtig),

hvorefter motoren tørnes, indtil den starter.

Not for

Reproduction

FARE FOR GIFTIG GAS. Motorens udstødningsgas indeholder kulilte,

en giftig gas, som kan slå en ihjel på få minutter. Du kan IKKE se den,

lugte den eller smage den. Du kan godt blive udsat for kulilte, selvom

du ikke kan lugte udstødningsgas. Hvis du begynder at føle dig dårlig

tilpas, svimmel eller svag under brug af dette produkt, skal du lukke for

det og sørge for at indånde frisk luft LIGE MED DET SAMME. Søg

lægehjælp. Du kan have kulilteforgiftning.

ADVARSEL

 Dette produkt må KUN betjenes udenfor langt fra vinduer, døre og

ventilationsanlæg for at reducere risikoen for at der samler sig kulilte, som kan

ledes til områder, hvor der befinder sig folk.

 Monter batteridrevne kuliltealarmer eller plug--in kuliltealarmer med

batteri-back-up i henhold til producentens anvisninger. Røgalarmer registrerer

ikke kuliltegas.

 Betjen IKKE dette produkt inden døre, i garager, k ældre, krybeområder, skure

eller andre delvist tillukkede områder, selv hvis der anvendes

ventilationsanordninger, eller hvis døre og vinduer er åbne for at foretage

gennemluftning. Der kan hurtigt samle sig kulilte i sådanne områder, som kan

blive hængende i flere timer, selv efter at produktet er blevet inaktiveret.

 Placer ALTID dette produkt i vindretningen, og lad motorens udstødning vende

væk fra områder, hvor der opholder sig folk.

BEMÆRK: Denne motor blev afsendt fra Briggs & Stratton uden olie. Før du starter

motoren, sørg altid for at påfylde olie i henhold til de instruktioner angivet i denne

manual. Hvis du starter motoren uden påfyldning af olie, vil denne blive beskadiget og vil

ikke kunne repareres mere og derfor ikke være dækket af garantien.

Bemærk: Udstyr kan have fjernbetjeninger. Se udstyrsmanualen for information om

fjernbetjeningernes placering og betjening.

1. Kontrollér motorolien. Se afsnittet Kontrol/påfyldning af olie.

2. Sørg for, at udstyrets kørselsbetjeni ngsanordninger, hvis monteret, er frakoblet.

3. Flyt gasspjældsregulatorstangen (A, figur 5), hvis monteret, til fast

position

(hurtig). Betjen motoren i fast

position (hurtig).

4. Når en ny motor startes for første gang, trykkes den røde spædebold hårdt ind (B)

fem gange. Ved efterfølgende startforsøg, trykkes s pædebolden ind tre gange (figur

5).

Bemærk: Hvis motoren kører tør for brændstof eller er blevet opbevaret over en

længere periode, kan det være nødvendigt at trykke på spædebolden 5 gange.

Bemærk: Det er normalt udnødvendigt at spæde ved genstart af en varm motor.

Bemærk: Hvis du trykker for mange gange på spædeanordningen, vil overskydende

brændstof drukne motoren, som vil være svær at starte.

5. Hvis maskinen er udstyret med et motorstopgreb (C), hold da motorens stopgreb

mod håndtaget (figur 6).

6. Hold fast i startsnorgrebet (D). Træk langsomt i startsnorgrebet, indtil du mærker

modstand, og træk derefter hurtigt i snoren (figur 5).

Bemærk: Hvis motoren ikke starter efter gentagne forsøg, gentag trin 4, 5, og 6. Hvis

den stadig ikke starter, gå til hjemmesiden BRIGGSandSTRATTON.COM eller ring

på 1-800-233-3723 (i USA).

ADVARSEL: Hurtig tilbagetrækning af startersnoren (tilbageslag) vil

trække hånd og arm tilbage mod motoren, hurtigere end du kan nå at slippe snoren.

Dette kan medføre, at du brækker armen, får knoglebrud, blå mærker eller

forstrækninger. Når motoren startes, træk langsomt i startsnoren indtil du mærker

modstand og træk derefter hurtigt for at undgå tilbageslag.

Afbrydelse af motoren - Figur

Slip motorens stophåndtag (E). Se figur 6.

eller

Motor med gasregulator: Flyt gasregulatoren (A, figur 5) til stillingen stop

edligeholdelse

BEMÆRK: Hvis motoren v ippes under vedligeholdelsesarbejde, skal brændstoftanken

være tom, og tændrørssiden skal vende opad. Hvis brændstoftanken ikke er tom, og

motoren vippes til en anden side, kan der opstå startvanskeligheder pga. olie eller

benzin, som har forurenet luftfilteret og/eller tændrøret.

ADVARSEL: Når der udføres vedligeholdelse, der kræver, at enheden

vippes, skal brændstoftanken være tom, da brændstoffet ellers kan løbe ud og

resultere i brand eller eksplosion.

Vi anbefaler, at du kontakter en autoriseret Briggs & Stratton forhandler vedrørende al

vedligeholdelse og service af motoren og motordele.

BEMÆRK: Alle dele i denne motor skal være korrekt placeret for at fungere korrekt.

Emissionsregulering

Vedligeholdelse, reservedelsudskiftning eller reparation af de

emissionsregulerende anordninger og systemer kan udføres af enhver person

eller ethvert ikke-vej motorreparationsværksted. Hvis du imidlertid ønsker at få udført

emissionsregulerende service “uden beregning”, så skal arbejdet udføres af en

fabriksautoriseret forhandler. Se under afsnittet Emissionsgaranti.

Gnister, som frembringes ved et uheld, kan medføre brand eller stød.

Hvis motoren startes ved et uheld, kan dette medføre, at personer

kommer i klemme i redskabets mekanismer, at legemsdele bliver

skåret af, eller at personer får snitsår.

Brandfare

ADVARSEL

Før justering eller reparation af motoren:

 Tag tændrørskablet af tændrøret, og hold det i sikker afstand fra tændrøret.

 Tag minuskablet af batteriet, hvis motoren er udstyret med el-starter.

 Brug kun korrekt værktøj.

 Foretag aldrig ændring af regulatorfjeder, regulatorforbindelser eller andre dele

for at øge motorens omdrejningstal.

 Udskiftningsdele skal være af samme design, og de skal monteres i samme

position som de originale dele. Andre reservedele fungerer muligvis ikke så

godt, kan evt. resultere i skader på enheden og kan måske resultere i

personskade.

 Slå aldrig på svinghjulet med en hammer eller en hård genstand, da dette kan få

svinghjulet til at splintres under drift.

Kontrol af gnist:

 Brug en godkendt gnisttester.

 Kontrollér ikke gnisten med tændrøret afmonteret.

Not for

Reproduction

BRIGGSandSTRATTON.COM

Vedligeholdelsesoversigt

Første fem timer

 Skift olie

For hver otte driftstimer eller hver dag

 Kontrollér oliestanden i motoren.

 Rengør området omkring lyddæmperen og betjeningsanordningerne

For hver 25 driftstimer eller én gang årligt

 Rengør luftfiltret *

For hver 50 driftstimer eller én gang årligt

 Skift motorolie

 Kontrollér lyddæmper og gnistfanger

En gang årligt

 Udskift luftfiltret

 Udskift tændrøret

 Rengør luftkølesystemet *

* Under støvede forhold eller når luftbåret snavs er til stede, rengør da oftere.

Justering af karburator og motorens omdrejningstal

Der må aldrig foretages justering af karburatoren eller motorens omdrejningstal.

Karburatoren er fra fabrikken indstillet til at fungere effektivt under de fleste driftsforhold.

Foretag aldrig ændring af regulatorfjeder, regulatorforbindelser eller andre dele for at

ændre motorens omdrejningstal. Hvis der skal foretages justering, kontakt da Briggs &

Strattons autoriserede servicecenter.

BEMÆRK: Udstyrsproducenten specificerer det maksimale motoromdrejningstal for en

motor, som den er monteret på udstyret. Overskrid ikke denne hastighed. Hvis du er i

tvivl om, hvad den maksimale hastighed er for udstyret, eller hvad motorens

omdrejningstal er indstillet på fra fabrikken, kontakt da Briggs & Strattons autoriserede

servicecenter for hjælp. For at opnå en sikker og korrekt drift af udstyret skal motorens

omdrejningstal altid justeres af en kvalificeret servicetekniker.

Udskiftning af tændrør - Figur

Kontrollér gnistgabet (A, figur 7) med en wire gauge til måling af tråddimensioner (B).

Regulér gabet, hvis dette er nødvendigt. Monter og fastspænd tændrøret til det

anbefalede tilspændingsmoment. For regulering eller spænding af gnistgabet, se

afsnittet Specifikationer.

Bemærk: I visse lande kræver lovgivningen brug af støjdæmpede tændrør for at dæmpe

tændingssignalet. Hvis motoren oprindeligt var udstyret med et støjdæmpet tændrør,

skal samme type tændrør anvendes ved udskiftning.

Efterse lyddæmper og gnistfanger - Figur