1
English
Thank you for purchasing the Yamaha SILENT Cello™. In order to obtain
the maximum performance and enjoyment from your SILENT Cello™, we
urge you to read this Owner’s Manual thoroughly before using the instru-
ment. Please keep this Owner’s Manual in a safe place for later reference.
Precautions ................................................................... 3
Main Unit/Accessories
................................................. 4
Nomenclature ............................................................... 5
Set up ............................................................................ 8
■
Tuning and Changing the Strings .............................................. 8
■
Setting the Knee Supports ........................................................11
■
About the Chest Support ......................................................... 12
■
About the End Pin .................................................................... 12
■
Attaching the Arm Support ....................................................... 12
Power Supply
.............................................................. 13
■
Using Batteries ........................................................................ 13
■
Supplying AC Power ................................................................ 13
Putting the Instrument into the Soft Case ................ 14
Specifications
............................................................. 15
SVC210
Owner’s Manual
Contents
™
WH39310_SVC210_Body_R4.indb 1 15/01/20 18:27
2
FCC INFORMATION (U.S.A.)
1.
IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions contained
in this manual, meets FCC requirements. Modifications not expressly
approved by Yamaha may void your authority, granted by the FCC, to
use the product.
2. IMPORTANT:
When connecting this product to accessories and/or
another product use only high-quality shielded cables. Cable/s supplied
with this product MUST be used. Follow all installation instructions.
Failure to follow instructions could void your FCC authorization to use
this product in the USA.
3. NOTE:
This product has been tested and found to comply with the
requirements listed in FCC Regulations, Part 15 for Class “B” digital de-
vices. Compliance with these requirements provides a reasonable level
of assurance that your use of this product in a residential environment
will not result in harmful interference with other electronic devices. This
equipment generates/uses radio frequencies and, if not installed and
used according to the instructions found in the user’s manual, may cause
interference harmful to the operation of other electronic devices. Com-
pliance with FCC regulations does not guarantee that interference will
not occur in all installations. If this product is found to be the source of
interference, which can be determined by turning the unit “OFF” and
“ON”, please try to eliminate the problem by using one of the following
measures:
Relocate either this product or the device that is being affected by the
interference.
Utilize power outlets that are on different branch (circuit breaker or
fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the antenna.
If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to co-
axial type cable.
If these corrective measures do not produce satisfactory results, please
contact the local retailer authorized to distribute this type of product. If
you cannot locate the appropriate retailer, please contact Yamaha Corpo-
ration of America, Electronic Service Division, 6600 Orangethorpe Ave,
Buena Park, CA 90620
The above statements apply ONLY to those products distributed by
Yamaha Corporation of America or its subsidiaries.
SPECIAL MESSAGE SECTION
92-BP
This product utilizes batteries or an external power supply (adaptor). DO NOT
connect this product to any power supply or adaptor other than one described
in the manual, on the name plate, or specifically recommended by Yamaha.
This product should be used only with the components supplied or; a cart,
rack, or stand that is recommended by Yamaha. If a cart, etc., is used, please
observe all safety markings and instructions that accompany the accessory
product.
SPECIFICATIONS SUBJECT TO CHANGE:
The information
contained in this manual is believed to be correct at the time of printing.
However, Yamaha reserves the right to change or modify any of the specifi-
cations without notice or obligation to update existing units.
Do not attempt to service this product beyond that described in the user-
maintenance instructions. All other servicing should be referred to qualified
service personnel.
This product, either alone or in combination with an amplifier and head-
phones or speaker/s, may be capable of producing sound levels that could
cause permanent hearing loss. DO NOT operate for long periods of time at
a high volume level or at a level that is uncomfortable. If you experience any
hearing loss or ringing in the ears, you should consult an audiologist.
IMPORTANT: The louder the sound, the shorter the time period before
damage occurs.
NOTICE:
Service charges incurred due to a lack of knowledge relating to
how a function or effect works (when the unit is operating as designed) are
not covered by the manufacturer’s warranty, and are therefore the owner’s
responsibility. Please study this manual carefully and consult your dealer
before requesting service.
ENVIRONMENTAL ISSUES:
Yamaha strives to produce products that
are both user safe and environmentally friendly. We sincerely believe that
our products and the production methods used to produce them meet these
goals. In keeping with both the letter and the spirit of the law, we want you
to be aware of the following:
Battery Notice:
This product MAY contain a small non-rechargeable
battery which (if applicable) is soldered in place. The average life span of
this type of battery is approximately five years. When replacement becomes
necessary, contact a qualified service representative to perform the replace-
ment.
This product may also use “household” type batteries. Some of these may be
rechargeable. Make sure that the battery being charged is a rechargeable type
and that the charger is intended for the battery being charged.
When installing batteries, do not mix old batteries with new, or with batteries
of a different type. Batteries MUST be installed correctly. Mismatches or
incorrect installation may result in overheating and battery case rupture.
Warning:
Do not attempt to disassemble or incinerate any battery. Keep
all batteries away from children. Dispose of used batteries promptly and as
regulated by the laws in your area. Note: Check with any retailer of house-
hold type batteries in your area for battery disposal information.
Disposal Notice:
Should this product become damaged beyond repair,
or for some reason its useful life is considered to be at an end, please observe
all local, state, and federal regulations that relate to the disposal of products
that contain lead, batteries, plastics, etc. If your dealer is unable to assist you,
please contact Yamaha directly.
NAMEPLATE LOCATION:
The nameplate is located on the back of the
product. The model number, serial number, power requirements, etc., are
located on this plate. You should record the model number, serial number,
and the date of purchase in the spaces provided below and retain this manual
as a permanent record of your purchase.
Model Serial No.
Purchase Date
CANADA*
THIS DIGITAL APPARATUS DOES NOT EXCEED THE “CLASS B” LIMITS FOR RADIO NOISE EMISSIONS FROM DIGITAL APPARATUS SET
OUT IN THE RADIO INTERFERENCE REGULATION OF THE CANADIAN DEPARTMENT OF COMMUNICATIONS.
LE PRESENT APPAREIL NUMERIQUE N’EMET PAS DE BRUITS RADIOELECTRIQUES DEPASSANT LES LIMITES APPLICABLES AUX AP-
PAREILS NUMERIQUES DE LA “CLASSE B” PRESCRITES DANS LE REGLEMENT SUR LE BROUILLAGE RADIO ELECTRI QUE EDICTE PAR
LE MINISTERE DES COMMUNICATIONS DU CANADA.
• This applies only to products distributed by Yamaha Canada Music Ltd.
• Ceci ne s’applique qu’aux produits distribués par Yamaha Canada Musique Ltée.
PLEASE KEEP THIS MANUAL
WH39310_SVC210_Body_R4.indb 2 15/01/20 18:27
3
Your SILENT Cello™ will give you years of reliable service if you follow the simple
rules given below:
■ Location
Do not expose it to the following conditions to avoid deformation, discoloration, or more serious
damage.
• Direct sunlight (e.g. near a window).
• High temperatures (e.g. near a heat source, outside, or in a car during the daytime).
• Excessive humidity.
• Excessive dust.
• Strong vibrations.
■ Power Supply
• Turn the power switch OFF when not in use.
• If you use an AC power adaptor, unplug the adaptor from the AC outlet if not to be used for an
extended period of time.
• Unplug the AC power adaptor during electric storms.
• Avoid plugging the AC power adaptor into the same AC outlet as appliances with high power
consumption, such as electric heaters or ovens. Also avoid using multi-plug adaptors since these
can result in reduced sound quality and possible damage.
■ Turn Power OFF When Making Connections
• To avoid damage to the SILENT Cello™ and other devices to which it is connected (a sound
system, for example), turn the power switches of all related devices OFF prior to connecting or
disconnecting audio cables.
■ Handling and Transport
• Never apply excessive force to the controls, connectors or other parts.
• Always unplug cables by gripping the plug firmly, not by pulling on the cable.
• Disconnect all cables before moving the unit.
• Physical shocks caused by dropping, bumping, or placing heavy objects on the unit can result in
scratches and more serious damage.
■ Cleaning
• Clean the body and control panel with a dry soft cloth.
• A slightly damp cloth may be used to remove stubborn grime and dirt.
• Never use cleaners such as alcohol or thinner.
■ Electrical Interference
• This unit contains digital circuitry and may cause interference if placed too close to radio or televi-
sion receivers. If this occurs, move it further away from the affected equipment.
Yamaha is not responsible for damage caused by improper handling or operation.
WH39310_SVC210_Body_R4.indb 3 15/01/20 18:27
4
Main Unit/Accessories
After opening the packaging, please check that all the parts listed below are
included.
SVC210
• Cello x 1
• Bridge x 1
• Audio cable x 1
(For connection of AUX IN jack)
• Chest support x 1
• Stereo headphones x 1
• Soft case x 1
• Arm support x 1
*
Power Adaptor (sold separately): Yamaha PA-3C (for use in Japan), PA-130 (for use internationally)
* To play SVC210, you will need 2 SUM-3 (AA) size batteries.
WH39310_SVC210_Body_R4.indb 4 15/01/20 18:27
5
Nomenclature
● Front
● Rear
Fingerboard
Neck
Saddle
Tuning peg
Nut
4th string (C)
3rd string (G)
Adjuster
Tailpiece
Body
Bridge seat
Tail nylon
End pin
End pin stopper
Bridge
2nd string (D)
1st string (A)
Knee support
arms
Knee support
lock knob
Controls
→ See page 6.
Arm support
fixing bolt
Chest support
attachment holes
Knee supports
Arm support
WH39310_SVC210_Body_R4.indb 5 15/01/20 18:27
6
POWER switch
REV. ON/ON/OFF
Lamp
PHONES jack
REVERB switch
RM (ROOM)
HL1 (HALL 1)
HL2 (HALL 2)
LINE OUT jack
DC-IN 9-12V jack (+
–)
(Power adaptor connector)
Battery cover
AUX VOL
(AUX volume)
AUX IN jack
VOLUME
● Controls
SUM-3 size battery x2
CD player,
MP3 player,
etc.
Stereo headphones
* Supplied headphones
or any other type
Powered speaker,
Electric tuner,
Mixer, Recorder,
Bass amplifier,
etc.
Cord hook
Wrap the Power Adaptor’s cord around the cord
hook (prevents cord from being unplugged).
Power adaptor
(Option)
Electric
outlet
WH39310_SVC210_Body_R4.indb 6 15/01/20 18:27
7
Caution
• When using the headphones, do not play using at high volume levels or for long periods of time.
Doing so can lead to irreparable damage to your hearing.
• Before connecting the SILENT Cello™ to any external devices, make sure that the power of all related
devices is turned OFF. Set the volume level of any external audio sources to the minimum level before
connecting anything. High volume settings could cause damage to the equipment and your hearing.
• If a connection cord is unplugged while the power is ON, it may result in damage to the equipment.
The sudden shock to your ears may be great, so please use with care.
• Be careful not to step on the cord. The cord may break, equipment may be damaged, and this may
cause a substantial shock to your ears.
• The signal from the SILENT Cello™ output jacks must NEVER be returned to the AUX IN jack, either
directly or through external equipment. Doing so will result in feedback which may cause damage
to the internal electronics.
• When connecting the instrument to external audio equipment, check the jack size and make sure to
use a plug size that corresponds to the jack being used, and properly connect the cable to the jack.
■ AUX IN jack
• The AUX IN jack, located on the rear of the
instrument, can be used to connect an external
stereo signal source to the SILENT Cello™.
Connecting the audio output of a CD player, etc.
to the instrument allows you to play along with
the external audio source.
• The AUX IN jack’s signal level can be controlled
with the AUX. VOL control.
■ LINE OUT jack
The LINE OUT jack, located on the rear of
the instrument, delivers the stereo signal of the
SILENT Cello™ to external audio equipment.
Using an optional stereo phone plug cable (or
monaural phone plug cable) to connect the
instrument to the audio input jack of external
Powered speakers, mixing console, etc. to listen
from external audio equipment or recording.
The LINE OUT jack’s signal level can be con-
trolled with the VOLUME control.
■ Basic Operation
1
Slide the POWER switch, located on the rear of
the instrument, to its ON position. The lamp will
light green.
2
Connect a pair of stereo headphones to the
PHONES jack on the rear of the instrument.
Make sure that the L&R sides of the headphones
are positioned on the correct ears.
3
Rotate the VOLUME dial to the desired playing
level.
■ Reverb Function
The SILENT Cello™ incorporates Yamaha’s
DSP reverb technology. Play while trying out
the three types of reverb.
1
Slide the POWER switch to the REV. ON posi-
tion, the lamp will light red, and reverb will be
applied to the SILENT Cello™ sound.
2
Slide the REVERB switch to select one of the
three reverb modes.
RM (ROOM): this reverb simulates the natural
reverberation found in a room.
HL1 (HALL 1): this reverb simulates the natural
reverberation found in a hall.
HL2 (HALL 2): the same reverb simulation as HL1
but with a longer decay time.
• When a powered speaker is connect to the LINE OUT jack, speakers with inadequate power ratings may
distort due to the low frequencies produced by the instrument. For sufficient headroom, used powered
speakers with a power rating of 50 watts or more.
• If the sound is distorted, rotate the VOLUME dial to the left.
WH39310_SVC210_Body_R4.indb 7 15/01/20 18:27
8
■ Tuning and Changing the Strings
The SILENT Cello™ is shipped from the factory with
the bridge unfitted. First, set up the bridge and then
proceed with tuning.
As the strings get old, sound quality will gradually
decrease, and it will become difficult to tune the
instrument. Change the strings as soon as you think
they are getting old.
• The end of the strings are sharp and can cut fingers. Use
caution when changing strings.
• When changing or adjusting strings, do not put your face
close to the instrument. The string may suddenly break
resulting in eye or other unexpected injuries.
• The lower side of the bridge supports the 1st string (A), the
higher side supports the 4th string (C). Make sure the bridge
is placed properly, then set the bridge in the bridge seat.
The side of the bridge with the logo imprint should face the
tailpiece.
• Ensure that the bridge stands vertically. If it leans to one side,
use both hands to adjust. Make sure that each string passes
over the corresponding slits in the bridge.
Make sure that the strings are resting in
their appropriate grooves in the bridge
when playing the instrument.
Strings may come out of their grooves when adjusting the
bridge or changing strings. Since the first (A) and fourth
(C) strings tend to come out of their grooves easily, use
your fingers to hold the strings gently in place when tun-
ing the instrument.
Always make sure that the bridge is standing
vertically, whether the instrument is being played
or stored.
Even if the bridge is standing vertically before tuning,
it may tilt during the tuning process. If so, readjust the
bridge so it stands vertically.
It is very important that the bridge stands vertically. If it
leans in either direction it will impair the sound and risk
damaging the instrument.
[Bridge is placed vertically]
Bridge seat
Bridge feet
[Looking from the tailpiece]
4th string
Logo
imprint
Set up
A
D
G
C
1st string
Slit
Correct
Escutcheon
Tailpiece
Body
Bad
Bad
Vertical
Caution
[Make sure that the strings do not
come out of their grooves]
A
D
G
C
WH39310_SVC210_Body_R4.indb 8 15/01/20 18:27
9
• The strings are tuned to the following pitches. The 1st
string is tuned to A, the 2nd string to D, the 3rd string
to G, and the 4th string to C.
Use a piano, tuning fork, tuner, etc., and adjust the pitch
of each string using the tuning pegs.
A
B
1st string (A)
4th string (C)
2nd string (D)
3rd string (G)
Lower
pitch
Raise
pitch
• Use the tension adjustment screw on the tuning machines to
adjust the amount of pressure required to turn the tuners.
* If the tuning machine turns with very slight pressure
→ Rotate the adjustment screw to the right (clockwise: A).
* If the tension is tight and the tuning machine is hard to turn
→ Rotate the adjustment screw to the left (counter-clock-
wise: B).
• Finally, use the adjuster to fine tune the strings.
If the adjuster is too
loose, it could produce
noise while playing.
Caution
Don’t loosen
too much.
Make sure that the
Tail Nylon is correctly
positioned on top of
the Saddle.
Caution
• When the instrument is not being used, loosen the strings until the pitch drops a whole tone.
• If the instrument is not going to be used for an extended period of time, loosen the strings even more.
• Before using the instrument, make sure that the bridge is positioned vertically. Damage to the bridge
and poor sound quality may result if the bridge is not properly positioned.
Tall nylon
Saddle
WH39310_SVC210_Body_R4.indb 9 15/01/20 18:27
10
● Winding the Strings
1
Before you string the instrument, set the adjuster so that
it is in the middle of its adjustment range. (All adjusters)
2
Place the ball (on the end of the string) in the notch on
the adjuster. Make sure the ball is properly inserted in the
adjuster’s notch.
3
At a point about 2 cm from the string’s end, bend the string at a right angle and insert the end into
the hole in the tuner. While pulling the string toward the bridge to maintain string tension, turn
the tuner machine to wind the string around the tuning post. Make sure the string is wound toward
the base of the post as shown in the illustration below.
The adjuster should be
set to the middle of its
adjustment range.
1st string (A)
4th string (C)
2nd string (D)
3rd string (G)
Adjuster’s notch
String
Ball
Insert the string’s
end into this hole
Wind the string
[Looking from the front]
String
About 2 cm
WH39310_SVC210_Body_R4.indb 10 15/01/20 18:27
11
■ Setting the Knee Supports
The SILENT Cello™ is shipped with the knee sup-
ports folded.
Before playing, follow the procedure shown below to
properly set the knee supports into position.
1
Loosen the knee support lock knob (about 3 turns).
• Do not loosen the knob too much.
2
Slowly unfold the knee support arms on both sides of the
instrument until they are fully open.
• If the arm is caught and cannot be opened, loosen the
knee support lock knob a little more.
Use caution when expanding the knee sup-
port arms. Do not pinch your hand or fingers
in the arms.
3
Tighten the knee support lock knob and make sure that the
knee support arms stay in place.
• Make sure the knee supports are firmly secured in place.
If they are loose, they may produce noise or cause the
instrument to move about while being played.
4
Slowly unfold the knee supports until they are fully open.
5
Slide the stoppers, located on the inner side of the knee
supports, over the arm to lock the knee supports in place.
With this, setting of the knee supports is complete. To
fold the knee supports simply reverse the order of the
procedure shown above.
Don’t tighten the knee support lock knob unless
the knee support arms are fully opened or fully
closed. Doing so may result in damage.
Due to the design, tightening the lock knob
when the arms are closed will not lock the
arms in place.
• Do not carry the instrument by the knee supports. Always carry the instrument by the neck or body.
1
22
Knee support
lock knob
Knee support arms
5
Stopper
3
44
Knee supports
WH39310_SVC210_Body_R4.indb 11 15/01/20 18:27
12
■ About the Chest Support
The chest support is used to rest the cello
against your body.
As shown in the illustration, insert the pins
on the chest support into the attaching holes
located on the back of the instrument.
■ About the End Pin
Loosen the end pin stopper, extend the end
pin to a comfortable length for playing and
firmly tighten the end pin stopper.
A rubber foot is attached to the tip of the
end pin. Removing the rubber foot exposes
the pointed end pin that can be used on ap-
propriate surfaces.
• The end pin is pointed. Please be careful when
using the exposed end pin.
• Make sure the end pin stopper is secured firmly
to prevent the instrument from slipping while
you play.
■ About the Arm Support
The SILENT Cello™ is shipped with the arm sup-
port detached.
Hold the arm support so that its attachment plate
is parallel to the attachment position on the body.
Tighten the arm support fixing bolt and secure the
arm support to the body.
• Make sure the arm support is firmly attached. If it is
loose, it may produce noise or cause the instrument
to move about while being played.
• Do not try to remove the arm support fixing bolt from
the instrument.
• Do not carry the instrument by the arm support.
Always carry the instrument by the neck or body.
Back of SILENT Cello™
Chest support
Pins
Rubber Foot
End Pin
End Pin
Stopper
Arm support
Arm support fixing bolt
WH39310_SVC210_Body_R4.indb 12 15/01/20 18:27
13
• Battery power is automatically disconnected when the AC adaptor is connected.
• When the AC adaptor is used, the batteries may leak. To prevent leakage we recommend that you
remove the batteries from the instrument. When the AC adapter is used.
•
When using an AC adaptor, make sure you use only the appointed compatible adaptor. The use of an
incompatible adaptor may result in damage to the instrument or cause fire, etc. Please use with caution.
Slide the POWER switch to the ON position, the lamp will light green. Slide the switch to
the REV. ON position, the lamp will flash red. When battery power is low, the lamp’s color
changes to orange, the sound becomes distorted, the Reverb does not properly function,
and noise becomes audible. When one of these symptoms appears, take note of the follow-
ing cautions and replace the batteries.
Caution
• Always follow the +/– signs when inserting the batteries. Improper insertion may result in fire.
• Always replace worn batteries with a complete set of new batteries. Never mix new and old bat-
teries. Do not mix different types of batteries (alkaline and manganese, or batteries from different
manufacturers, or different types by the same manufacturer). Doing so may result in fire.
• To prevent possible damage to the unit due to battery leakage and unnecessary power drain,
remove the batteries from the unit when it is not going to be used for an extended period of time.
Power Supply
The SILENT Cello™ can be operated with either battery or AC power. Always
turn the power switch (OFF/ON/REV.ON) on the rear panel OFF before making
AC power connections or replacing batteries.
■ Using Batteries
1
Open the battery compartment situated on the back
of the SILENT Cello™.
2
Insert the two batteries (SUM-3 size). Take care-
ful note of the polarity markings as shown in the
illustration above, and insert the batteries.
3
Replace the battery compartment cover.
■ Supplying AC Power
Power Adaptor (sold separately): Yamaha PA-3C (for use in Japan), PA-130 (for use internationally)
1
Plug the adaptor’s DC output cable into the SILENT Cello™ DC IN 9-12V jack located on the back of
the instrument, making sure the plug is firmly inserted into the jack.
2
Plug the AC adaptor into a convenient wall AC power socket.
Bij dit produkt zijn batterijen geleverd.
Wanneer deze leeg zijn, moet u ze niet
weggooien maar inleveren als KCA.
Battery compartment
cover
* For customers in the Netherlands
SUM-3 size
battery x2
WH39310_SVC210_Body_R4.indb 13 15/01/20 18:27
14
About the Supplied Soft Case
● Placing the cello in the case
1
Fold up the knee supports, and remove the chest and
arm supports from the SILENT Cello™.
Slide the end pin all the way into the instrument, and
tighten the end pin stopper to secure.
2
First place the end pin end of the instrument into the
soft case q, followed by the head end of the instru-
ment w.
● Setting the Protector
1
Starting with the bridge side of the protector, slide it
at an angle between the knee supports and case e.
2
Gently push the end pin end of the protector into place
r.
● The Storage Pockets
Bow pocket
Arm support, etc.
Chest support, etc.
Cable, Headphones, etc.
Protector
Protector
* The protector does not guarantee against damage to parts such as the bridge, etc.
• The protector is designed to protect the instrument
against light shocks while the instrument is being
carried. Never expose the protector to shocks such
as placing the case with the protector facing down,
placing objects on top of or hitting the protector.
The supplied soft case is designed specifically for use with the SVC210 SILENT
Cello™. Attaching the protector (included in the case) allows storage and trans-
port of the instrument with its bridge attached.
• When storing the bow in the bow pocket,
always place the bow in its case.
WH39310_SVC210_Body_R4.indb 14 15/01/20 18:27
15
Specifications
Neck Maple
Body Spruce/Maple
Fingerboard Ebony
Bridge Maple (Aubert)
Knee Supports/Arm Support Beech
Tuning Pegs Worm Gear Type
Tail Piece Adjuster 4 pieces (Wittner)
Strings Ball-end type (Helicore)
Sensor Piezo pick-up
Connectors/Controls • Headphone Output
• AUX IN (w/Volume Control)
• LINE OUT
• Volume
• Reverb Switch (RM/HL1/HL2)
Power • POWER Switch (OFF/ON/REV. ON)
• SUM-3 size battery x2
Power Consumption 2.5 W (with the PA-3C),
1.0 W (with the PA-130, PA-130A, B)
Battery Life (Continuous Use) Using Manganese batteries
• Without Reverb (POWER Switch “ON”)
approximately 10 hours
• With Reverb (POWER Switch “REV. ON”)
approximately 3 hours
Using Alkaline batteries
• Without Reverb (POWER Switch “ON”)
approximately 25 hours
• With Reverb (POWER Switch “REV. ON”)
approximately 9 hours
String Length 690 mm (27-3/8”)
Dimensions (setup for playing with the chest support attached)
1,251 (L) x 438 (W) x 243 (H) mm
49-1/4” (L) x 17-1/4” (W) x 9-9/16” (H)
Weight
(with batteries and chest support)
3.9kg (8 lbs. 2 oz.)
* Design and specifications are subject to change without notice.
WH39310_SVC210_Body_R4.indb 15 15/01/20 18:27
WH39310 1502 R4 Printed in Japan
430-8650 10-1
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
in andere talen
- English: Yamaha SVC210 Owner's manual
- italiano: Yamaha SVC210 Manuale del proprietario
- русский: Yamaha SVC210 Инструкция по применению
- français: Yamaha SVC210 Le manuel du propriétaire
- español: Yamaha SVC210 El manual del propietario
- Deutsch: Yamaha SVC210 Bedienungsanleitung
- português: Yamaha SVC210 Manual do proprietário
- dansk: Yamaha SVC210 Brugervejledning
- suomi: Yamaha SVC210 Omistajan opas
- čeština: Yamaha SVC210 Návod k obsluze
- svenska: Yamaha SVC210 Bruksanvisning
- Türkçe: Yamaha SVC210 El kitabı
- polski: Yamaha SVC210 Instrukcja obsługi
- română: Yamaha SVC210 Manualul proprietarului
