Yamaha Clavinova CLP-320 de handleiding

Merk: Yamaha

Model: Clavinova CLP-320

Categorie: Aanvullende muziekapparatuur

Type: de handleiding

Deze handleiding is ook geschikt voor

CLP-320

OWNER’S MANUAL

IMPORTANT

—Check your power supply—

Make sure that your local AC mains voltage matches the voltage specified on the name plate on the bottom panel. In some areas a voltage selector may

be provided on the bottom panel of the main keyboard unit near the power cord. Make sure that the voltage selector is set for the voltage in your area.

The voltage selector is set at 240V when the unit is initially shipped. To change the setting use a "minus" screwdriver to rotate the selector dial so that the

correct voltage appears next to the pointer on the panel.

For information on assembling the keyboard stand, refer to the instructions at the end of this manual.

ENGLISH

CLP-320

Owner’s Manual

Introduction

92-469

(bottom)

SPECIAL MESSAGE SECTION

PRODUCT SAFETY MARKINGS:

Yamaha electronic

products may have either labels similar to the graphics

shown below or molded/stamped facsimiles of these

graphics on the enclosure. The explanation of these

graphics appears on this page. Please observe all cautions

indicated on this page and those indicated in the safety

instruction section.

See bottom of Keyboard enclosure for graphic symbol markings.

The exclamation point within the

equilateral triangle is intended to alert

the user to the presence of important

operating and maintenance (servic-

ing) instructions in the literature

accompanying the product.

The lightning ﬂash with arrowhead

symbol, within the equilateral trian-

gle, is intended to alert the user to the

presence of uninsulated “dangerous

voltage” within the product’s enclo-

sure that may be of sufﬁcient magni-

tude to constitute a risk of electrical

shock.

IMPORTANT NOTICE:

All Yamaha electronic products

are tested and approved by an independent safety testing

laboratory in order that you may be sure that when it is

properly installed and used in its normal and customary

manner, all foreseeable risks have been eliminated. DO

NOT modify this unit or commission others to do so

unless speciﬁcally authorized by Yamaha. Product perfor-

mance and/or safety standards may be diminished.

Claims ﬁled under the expressed warranty may be denied

if the unit is/has been modiﬁed. Implied warranties may

also be affected.

SPECIFICATIONS SUBJECT TO CHANGE:

The

information contained in this manual is believed to be

correct at the time of printing. However, Yamaha reserves

the right to change or modify any of the speciﬁcations

without notice or obligation to update existing units.

ENVIRONMENTAL ISSUES:

Yamaha strives to pro-

duce products that are both user safe and environmentally

friendly. We sincerely believe that our products and the

production methods used to produce them, meet these

goals. In keeping with both the letter and the spirit of the

law, we want you to be aware of the following:

Battery Notice:

This product MAY contain a small non-

rechargable battery which (if applicable) is soldered in

place. The average life span of this type of battery is

approximately ﬁve years. When replacement becomes

necessary, contact a qualiﬁed service representative to

perform the replacement.

Warning:

Do not attempt to recharge, disassemble, or

incinerate this type of battery. Keep all batteries away

from children. Dispose of used batteries promptly and as

regulated by applicable laws. Note: In some areas, the

servicer is required by law to return the defective parts.

However, you do have the option of having the servicer

dispose of these parts for you.

Disposal Notice:

Should this product become damaged

beyond repair, or for some reason its useful life is consid-

ered to be at an end, please observe all local, state, and

federal regulations that relate to the disposal of products

that contain lead, batteries, plastics, etc.

NOTICE:

Service charges incurred due to lack of knowl-

edge relating to how a function or effect works (when the

unit is operating as designed) are not covered by the man-

ufacturer’s warranty, and are therefore the owners respon-

sibility. Please study this manual carefully and consult

your dealer before requesting service.

NAME PLATE LOCATION:

The graphic below indi-

cates the location of the name plate. The model number,

serial number, power requirements, etc., are located on

this plate. You should record the model number, serial

number, and the date of purchase in the spaces provided

below and retain this manual as a permanent record of

your purchase.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Model

Serial No.

Purchase Date

CLP-320

ENGLISH

CLP-320

Owner’s Manual

The above warning is located on the bottom side of the unit.

Explanation of Graphical Symbols

The lightning ﬂash with arrowhead symbol

within an equilateral triangle is intended to alert

the user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufﬁcient magnitude to

constitute a risk of electric shock to persons.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the product.

IMPORTANT SAFETY INSTRUCTIONS

1 Read these instructions.

2Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8 Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

ampliﬁers) that produce heat.

9 Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug

has two blades and a third grounding prong. The wide

blade or the third prong are provided for your safety. If

the provided plug does not ﬁt into your outlet, consult

an electrician for replacement of the obsolete outlet.

10 Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the

point where they exit from the apparatus.

11 Only use attachments/accessories speciﬁed by the

manufacturer.

12 Use only with the cart, stand,

tripod, bracket, or table speciﬁed

by the manufacturer, or sold with

the apparatus. When a cart is

used, use caution when moving

the cart/apparatus combination

to avoid injury from tip-over.

13 Unplug this apparatus during

lightning storms or when unused for long periods of

time.

14 Refer all servicing to qualiﬁed service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or plug

is damaged, liquid has been spilled or objects have

fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally,

or has been dropped.

(UL60065_03)

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

ENGLISH

CLP-320

Owner’s Manual

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical

shock, short-circuiting, damages, ﬁre or other hazards. These precautions include, but are not limited to, the following:

• Only use the voltage speciﬁed as correct for the instrument. The required

voltage is printed on the name plate of the instrument.

• Check the electric plug periodically and remove any dirt or dust which may have

accumulated on it.

• Use only the supplied power cord/plug.

• Do not place the power cord near heat sources such as heaters or radiators, and

do not excessively bend or otherwise damage the cord, place heavy objects on

it, or place it in a position where anyone could walk on, trip over, or roll anything

over it.

• Do not open the instrument or attempt to disassemble the internal parts or

modify them in any way. The instrument contains no user-serviceable parts. If it

should appear to be malfunctioning, discontinue use immediately and have it

inspected by qualiﬁed Yamaha service personnel.

• Do not expose the instrument to rain, use it near water or in damp or wet

conditions, or place containers on it containing liquids which might spill into

any openings. If any liquid such as water seeps into the instrument, turn off the

power immediately and unplug the power cord from the AC outlet. Then have

the instrument inspected by qualiﬁed Yamaha service personnel.

• Never insert or remove an electric plug with wet hands.

• Do not put burning items, such as candles, on the unit.

A burning item may fall over and cause a ﬁre.

• If the power cord or plug becomes frayed or damaged, or if there is a sudden

loss of sound during use of the instrument, or if any unusual smells or smoke

should appear to be caused by it, immediately turn off the power switch,

disconnect the electric plug from the outlet, and have the instrument inspected

by qualiﬁed Yamaha service personnel.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage

to the instrument or other property. These precautions include, but are not limited to, the following:

• When removing the electric plug from the instrument or an outlet, always hold

the plug itself and not the cord. Pulling by the cord can damage it.

• Remove the electric plug from the outlet when the instrument is not to be used

for extended periods of time, or during electrical storms.

• Do not connect the instrument to an electrical outlet using a multiple-connector.

Doing so can result in lower sound quality, or possibly cause overheating in the

outlet.

• Read carefully the attached documentation explaining the assembly process.

Failure to assemble the instrument in the proper sequence might result in

damage to the instrument or even injury.

• Do not expose the instrument to excessive dust or vibrations, or extreme cold or

heat (such as in direct sunlight, near a heater, or in a car during the day) to

prevent the possibility of panel disﬁguration or damage to the internal

components.

• Do not use the instrument in the vicinity of a TV, radio, stereo equipment,

mobile phone, or other electric devices. Otherwise, the instrument, TV, or radio

may generate noise.

• Do not place the instrument in an unstable position where it might accidentally

fall over.

• Before moving the instrument, remove all connected cables.

• When setting up the product, make sure that the AC outlet you are using is

easily accessible. If some trouble or malfunction occurs, immediately turn off

the power switch and disconnect the plug from the outlet. Even when the power

switch is turned off, electricity is still ﬂowing to the product at the minimum

level. When you are not using the product for a long time, make sure to unplug

the power cord from the wall AC outlet.

Power supply/Power cord

Do not open

Water warning

Fire warning

If you notice any abnormality

Power supply/Power cord

Assembly

Location

(1)B-12

1/2

ENGLISH

CLP-320

Owner’s Manual

• Before connecting the instrument to other electronic components, turn off the

power for all components. Before turning the power on or off for all

components, set all volume levels to minimum. Also, be sure to set the volumes

of all components at their minimum levels and gradually raise the volume

controls while playing the instrument to set the desired listening level.

• In the case of a model with a polished ﬁnish, gently remove dust and dirt with a

soft cloth. Do not wipe too hard since small particles of dirt can scratch the

instrument’s ﬁnish.

• When cleaning the instrument, use a soft,dry or slightly damp cloth. Do not use

paint thinners, solvents, cleaning ﬂuids, or chemical-impregnated wiping

cloths.

•Take care that the key cover does not pinch your ﬁngers, and do not insert a

ﬁnger or hand in any gaps on the key cover or instrument.

• Never insert or drop paper, metallic, or other objects into the gaps on the key

cover, panel or keyboard. If this happens, turn off the power immediately and

unplug the power cord from the AC outlet. Then have the instrument inspected

by qualiﬁed Yamaha service personnel.

• Do not place vinyl, plastic or rubber objects on the instrument, since this might

discolor the panel or keyboard.

• In the case of a model with a polished ﬁnish, bumping the surface of the

instrument with metal, porcelain, or other hard objects can cause the ﬁnish to

crack or peel. Use caution.

• Do not rest your weight on, or place heavy objects on the instrument, and do not

use excessive force on the buttons, switches or connectors.

• Do not use the instrument/device or headphones for a long period of time at a

high or uncomfortable volume level, since this can cause permanent hearing

loss. If you experience any hearing loss or ringing in the ears, consult a

physician.

• Do not place the bench in an unstable position where it might accidentally fall

over.

• Do not play carelessly with or stand on the bench. Using it as a tool or step-

ladder or for any other purpose might result in accident or injury.

• Only one person should sit on the bench at a time, in order to prevent the

possibility of accident or injury.

• If the bench screws become loose due to extensive long-term use, tighten them

periodically using the included tool.

Saving and backing up your data

• Data in the instrument’s internal memory can be lost due to operational errors or

malfunction. Be sure to save any important data to external media via a

computer connected to the instrument. (page 31)

Always turn the power off when the instrument is not in use.

Even when the power switch is turned off, electricity is still ﬂowing to the instrument at the minimum level. When you are not using the instrument for a long time, make sure

you unplug the AC power plug from the wall AC outlet.

Connections

Maintenance

Handling caution

Using the bench (If included)

Saving data

Yamaha cannot be held responsible for damage caused by improper use or modiﬁcations to the instrument, or data that is lost or destroyed.

(1)B-12

2/2

Welcome

CLP-320

Owner’s Manual

ENGLISH

Welcome

Thank you for purchasing the Yamaha Clavinova! We recommend that you read this manual carefully so that you can take

full advantage of the advanced and convenient functions of your new Clavinova.

We also recommend that you keep this manual in a safe, convenient place for future reference.

About the Documentation and Refer-

ence Materials for this Instrument

The documentation and reference materials for this instrument consist of the following:

Owner’s Manual (this book)

Introduction (P2):

Please read this section ﬁrst.

Reference (P15):

This section explains how to make detailed settings for the instrument’s various functions.

Appendix (P40):

This section introduces speciﬁcations and other information.

Quick Operation Guide (separate sheet)

This Guide explains detailed operation of the functions assigned to the buttons and keyboard.

Data List

You can download various MIDI-related reference materials, such as the MIDI Data Format and MIDI Implementa-

tion Chart, from the

Yamaha Manual Library

Connect to the Internet, visit the following website, type the model name of your instrument (such as “CLP-320”) in

the Model Name text box, then click the Search button.

Yamaha Manual Library

http://www.yamaha.co.jp/manual/

•The illustrations as shown in this owner’s manual are for instructional purposes only, and may be different from the

ones on your instrument.

Trademarks:

•Windows is a registered trademark of Microsoft® Corporation in the United States and other countries.

•The company names and product names in this manual are the trademarks or registered trademarks of their respective companies.

This product incorporates and bundles computer programs and contents in which Yamaha owns copyrights or with

respect to which it has license to use others’ copyrights. Such copyrighted materials include, without limitation, all

computer software, style ﬁles, MIDI ﬁles, WAVE data, musical scores and sound recordings. Any unauthorized use of

such programs and contents outside of personal use is not permitted under relevant laws. Any violation of copyright

has legal consequences. DON’T MAKE, DISTRIBUTE OR USE ILLEGAL COPIES.

Copying of the commercially available musical data including but not limited to MIDI data and/or audio data is

strictly prohibited except for your personal use.

Accessories

CLP-320

Owner’s Manual

ENGLISH

Accessories

• Owner’s Manual (this book)

• Quick Operation Guide (separate sheet)

• “50 Greats for the Piano” (Music Book)

• AC Power cord

• Bench*

* Included or optional depending on locale.

Tuning

Unlike an acoustic piano, this instrument does not need to be tuned. It always stays perfectly in tune.

Transporting

If you move to another location, you can transport this instrument along with your other belongings. You can move

the unit as it is (assembled) or you can disassemble the unit before moving.

Tr ansport the keyboard horizontally. Do not lean it up against a wall or stand it up on its side. Do not subject the

instrument to excessive vibration or shock.

Features

CLP-320

Owner’s Manual

ENGLISH

Features

AWM Dynamic Stereo Sampling

The Yamaha Clavinova CLP-320 digital piano offers a rich and versatile range of sounds, which are created using

Yamaha’s proprietary sampling tone-generation system, “AWM Dynamic Stereo Sampling.”

The AWM (Advanced Wave Memory) is a sampling system which creates sound close to that of an acoustic instru-

ment by using digital technology to record the instrument sound and applying high-quality digital ﬁlter technology

to the recorded audio samples.

The waveform of the sound created by playing the key of an acoustic piano differs depending on the playing

strength from pianissimo to fortissimo. The AWM Dynamic Stereo Sampling can produce such dynamic nuances by

recording samples of various playing strengths. The greater the number of samples used, the higher the expressive

quality and potential becomes.

The piano voice “Grand Piano 1” , features totally new sample recorded from a full-size concert grand piano. Each

note in the sample has been adjusted meticulously so that the digital piano will play only the very best piano sounds.

The piano voices are well-separated sounds featuring a fast attack and a satisfying response.

The “Grand Piano 1” voice features multiple wave samples for different velocities (Dynamic Sampling); that is, dif-

ferent samples are used depending on how fast or strong you strike the keys. Therefore, this voice expresses detailed

dynamics and sounds much closer to a true acoustic piano.

GH(Graded Hammer) keyboard

A special Graded Hammer keyboard on the CLP-320, features graded key weight and response throughout the key-

board range. They respond to a heavier touch in the low range of the keyboard and a lighter touch in the higher

range of the keyboard, thus providing natural grand-piano type playability. The matte ﬁnish of the black keys

enhances keyboard’s luxurious appearance. The Graded Hammer keyboard also offers superb playability for trem-

olo and other repetitive-striking techniques.

Table of Contents

CLP-320

Owner’s Manual

ENGLISH

Table of Contents

Introduction

SPECIAL MESSAGE SECTION ...................... 2

About the Documentation and Reference

Materials for this Instrument...................... 6

Accessories .................................................. 7

Features....................................................... 8

Part Names and Functions........................ 10

Before Using.............................................. 12

Key Cover ..........................................................12

Music Rest .........................................................12

Connecting the Power Cord.............................13

Turning the Power On......................................13

Setting the Volume............................................14

Using Headphones............................................14

Reference

Listening to the Demo Songs ................... 15

Listening to 50 Piano Preset Songs .......... 16

Listening to Songs Loaded from the

Computer .................................................. 17

Selecting & Playing Voices........................ 18

Selecting Voices.................................................18

Using the Pedals ................................................19

Adding Variations to the Sound – Reverb.......20

Layering Two Voices (Dual mode) ..................21

Transposition ....................................................22

Fine-tuning the Pitch........................................22

Using the Metronome.......................................23

Adjusting the Keyboard Touch (Touch

Sensitivity) .........................................................24

Recording your Performance.................... 25

Playing Back Recorded Performance Data ......26

Erasing Recorded Performance Data ...............26

Connecting MIDI Instruments .................. 27

About MIDI ...................................................... 27

MIDI’s Capability ............................................. 27

Connecting a Computer ...........................28

MIDI Functions ..........................................29

MIDI Transmit/Receive Channel Selection .... 29

Local Control ON/OFF .................................... 29

Program Change ON/OFF............................... 30

Control Change ON/OFF ................................ 30

Transmitting Song Data between the

Computer and the Clavinova.................... 31

Loading Song Data from a Computer to the

Clavinova .......................................................... 31

Transmitting Song Data from the Clavinova to a

Computer.......................................................... 32

Backing up Data and Initializing the Settings. 32

Troubleshooting........................................ 33

Options...................................................... 33

Keyboard Stand Assembly ........................34

Index.......................................................... 38

Appendix

Specifications ............................................40

Part Names and Functions

CLP-320

Owner’s Manual

ENGLISH

Part Names and Functions

POWER

PHONES

[DEMO/SONG]

Listen to the playback of a demo song for each

voice and 50 piano preset songs (page 15).

[METRONOME]

Control the metronome functions (page 23).

[REC]

Record your performance (page 25).

[PLAY]

Play back your recorded performance (page 26).

[MASTER VOLUME]

Adjust the volume level using this control (page 14).

[+]/[–]

These buttons enable you to select a song to play

back from voice demo songs or from “50 Greats

for the Piano.” (pages 15, 16)

They also enable you to change the voice or

tempo. (pages 18, 23)

[PIANO/VOICE]

This button enables you to select any voice from

10 voices. (page 18)

You can also layer two voices (page 21), or select a

type of reverb (page 20).

[PHONES]

A set of standard stereo headphones can be

plugged in here for private practice (page 14).

[POWER]

This power switch turns the power to the

unit on or off. (page 13)

Bottom of the keyboard

Part Names and Functions

CLP-320

Owner’s Manual

ENGLISH

MIDI

INOUT

PEDAL

POWER

[PEDAL]

Connect the pedal cord (page 36).

MIDI [IN/OUT]

Connect a MIDI device to this connector to

use various MIDI functions.

(Connecting MIDI Instruments—page 27)

Shows the MIDI [IN/OUT] and [PEDAL]

jacks as seen when viewed from the rear of

the instrument.

[AC IN]

Connect the included power cord here.

(page 13)

Pedals

Use these pedals when you want notes to

sustain longer or to sound softer and round.

(Using the Pedals—page 19)

Bottom of the keyboard

Before Using

CLP-320

Owner’s Manual

ENGLISH

Before Using

Key Cover

To open the key cover:

Lift the cover slightly, then push and slide it

open.

To close the key cover:

Slide the cover toward you and gently lower the

cover over the keys.

CAUTION

Hold the cover with both hands when opening or

closing it. Do not release it until it is fully opened or

closed. Be careful to avoid catching ﬁngers (yours or

others, especially children’s) between the cover and

main unit.

CAUTION

Do not place objects, such as a piece of metal or paper, on top of the key cover. Small objects placed on the key cover

may fall inside the unit when the cover is opened and may be nearly impossible to remove. This could cause electric

shock, short circuit, ﬁre or other serious damage to the instrument.

If this happens, turn off the power immediately and unplug the power cord from the AC outlet. Then have the instrument

inspected by qualiﬁed Yamaha service personnel.

Music Rest

To raise the music rest:

1. Pull the music rest up and toward yourself as far as it will

go.

2. Flip down the two metal supports at the left and right on

the rear of the music rest.

3. Lower the music rest so that it rests on the metal sup-

ports.

To lower the music rest:

1. Pull the music rest toward yourself as far as it will go.

2. Raise the two metal supports (at the rear of the music

rest).

3. Gently lower the music rest backward until it is all the

way down.

CAUTION

Do not try to use the music rest in a half-raised position.

When lowering the music rest, do not release your hands

from the music rest until it is all the way down.

CAUTION

Be careful to avoid catching your ﬁngers

when opening or closing the cover.

Before Using

CLP-320 Owner’s Manual

ENGLISH

Connecting the Power Cord

Read the instructions below very carefully to make sure that you correctly connect the power cord.

1. Insert the plug on one end of the power cord to the [AC IN] connector. Refer to the “Part Names and

Functions” on page 11 for information on the location of the [AC IN] connector.

2. Insert the plug on the other end of the power cord to a standard AC outlet.

(The shape of the plug differs depending on locale.)

WARNING

Make sure your Clavinova is rated for the AC voltage supplied in the area in which the piano will be used. (The voltage rating appears on

the name plate on the bottom panel). In some areas, a voltage selector may be provided on the bottom panel of the main keyboard unit

near the power cord. Make sure that the voltage selector is set for the voltage in your area. Connecting the unit to an inappropriate AC

supply can seriously damage the internal circuitry and may even pose a shock hazard!

Use only the AC power cord supplied with the instrument. If the supplied power cord is lost or damaged and needs to be replaced, contact

your Yamaha dealer. The use of an inappropriate replacement can pose a ﬁre and shock hazard!

The type of AC power cord provided with the instrument may be different depending on the country in which the instrument was pur-

chased. (In some areas a plug adaptor may be provided to match the pin conﬁguration of the AC wall outlets in your area.)

Do NOT modify the plug provided with the instrument. If the plug will not ﬁt the outlet, have a proper outlet installed by a qualiﬁed electri-

cian.

Turning the Power On

Press the [POWER] switch on the right end of the keyboard to turn on the power to the unit.

The power indicator located below the left end of the keyboard lights up.

Press the [POWER] switch again to turn off the power to the unit.

The power indicator turns off.

Power indicator

If you forget to turn off the power to the piano and close the key cover, the power indicator will remain lit, indicating that

the power is still on.

CAUTION

A small amount of electrical current remains even after the power switch is turned off. If you plan not to use the instru-

ment for a long period of time, be sure to unplug the instrument from the AC outlet.

(Bottom of the

keyboard)

Power indicator

[POWER]

Before Using

CLP-320 Owner’s Manual

ENGLISH

Setting the Volume

When you start playing, adjust the [MASTER VOLUME] control to the most comfortable listening level.

CAUTION

Do not use this instrument at a high volume level for a long period of time, or your hearing may be damaged.

Using Headphones

Connect a pair of headphones to one of the [PHONES] jacks.

Two [PHONES] jacks are provided.

You can connect two sets of standard stereo headphones. (If you are

using only one pair of headphones, you can plug them into either

jack.)

CAUTION

Do not listen to the instrument at a high volume level through head-

phones for a long period of time, or your hearing may be damaged.

Using the Headphone Hanger

A headphone hanger is included in the package so that you can hang the head-

phones on this instrument. Install the headphone hanger using the included

two screws (4 × 10mm) as shown in the ﬁgure.

CAUTION

Do not hang anything other than the headphones on the hanger. Otherwise,

this instrument or the hanger may be damaged.

The level decreases. The level increases.

PHONES

Bottom of the keyboard

Standard stereo

phone plug

PHONES

Listening to the Demo Songs

CLP-320 Owner’s Manual

ENGLISH

Listening to the Demo Songs

Demo songs are provided that effectively demonstrate each of this instrument’s voices.

Refer to the voice list on

page 18 for more information on

the characteristics of each pre-

set voice.

1. Turn on the power.

While a demo song is playing,

press and hold down the [MET-

RONOME] button and press the

[+] or [–] button to change the

song tempo.

If you are using the metronome

(page 23) during demo song

playback, press the [+] or [–]

button to change the song

tempo.

You can also press keys to

change the tempo. (page 23)

The demo songs will not be

transmitted via MIDI.

You can also change to the next

or previous demo song by

pressing and holding down the

[DEMO/SONG] button and

pressing the [+] or [–] button.

Adjusting the Volume

Use the [MASTER VOLUME]

control to adjust the volume.

(In case the power is not turned on) Press the [POWER] button.

2. Start playing back a demo song.

Press the [DEMO/SONG] button.

The demo song for the currently-selected voice starts playing.

3. Select and play a demo song.

While a demo song is playing, press the [+] or [–] button to select and play the

next or previous demo song.

If you wish to select a particular demo song from 10 voice demo songs, press

and hold down the [DEMO/SONG] button, then press one of the C1–A1 keys.

The selected demo song starts to play. Starting with the selected song, the

playback of the demo songs will continue in the following sequence: other

voice demo songs, followed by 50 piano preset songs, and any songs

loaded from the computer. The sequence then returns to the ﬁrst demo

song and repeats until you stop it.

Demo Songs

Each of the 10 voices features its own demo song that showcases the corre-

sponding voice. Please refer to “Selecting Voices” on page 18.

The demo songs listed below are re-arranged excerpts from the original compo-

sitions.

tion).

4. Stop the Voice demo.

Press the [DEMO/SONG] button to stop playback.

Procedure

C1 A1

The lowest key

Key Voice Name Title Composer

C1 GRAND PIANO 1 Albumbrad, Lyriske stykker IV, op.47-2 E. H. Grieg

E1 HARPSICHORD 1 Concerto a cembalo obbligato, 2 violini, viola e continuo No.7, BWV.1058 J. S. Bach

F1 HARPSICHORD 2 Gigue, Französische Suiten Nr.5, BWV.816 J. S. Bach

G1 CHURCH ORGAN 1 Herr Christ, der ein’ge Gottes-Sohn, BWV.601 J. S. Bach



1 CHURCH ORGAN 2 Triosonate Nr.6, BWV.530 J. S. Bach

Reference

Listening to 50 Piano Preset Songs

CLP-320 Owner’s Manual

ENGLISH

Listening to 50 Piano Preset Songs

The Clavinova provides performance data for 50 piano songs as well as voice demo songs. You can

simply listen to these songs. You can also refer to the included “50 Greats for the Piano” that con-

tains scores for 50 piano preset songs.

1. Select and play back a piano preset song.

You can play the keyboard

along with the preset song. You

can change the voice playing on

the keyboard.

The default tempo is automati-

cally selected whenever a new

preset song is selected, and

when a new preset song begins

playback.

While a piano preset song is

playing, hold down the [MET-

RONOME] button and press the

[+] or [–] button to change the

song tempo.

If you are using the metronome

(page 23) during preset song

playback, press the [+] or [–]

button to change the song

tempo.

You can also press keys to

change the tempo. (page 23)

When you select a different

song (or a different song is

selected during chained play-

back), an appropriate reverb

type will be selected accord-

ingly.

The 50 piano preset songs will

not be transmitted via MIDI.

The number of each piano preset song is assigned to the C2–C



6 keys.

While holding down the [DEMO/SONG] button, press one of the C2–C



6 keys

to select a song to play back.

The selected piano song starts to play.

To play all preset songs consecutively in sequence, while holding down the

[DEMO/SONG] button, press the D6 key.

While a piano preset song is playing, press the [+] or [–] button to change to the

next or previous piano song.

Adjusting the Volume

Use the [MASTER VOLUME] control to adjust the volume.

2. Stop playback.

To stop the song during playback (or continuous playback), press the [DEMO/

SONG]

button.

•To continue playing other songs, see procedure 1 above.

Procedure

Song:

On this instrument, perfor-

mance data is called a

“Song.” This includes demo

songs and 50 piano preset

tunes.

C2 C4C3 C5

The highest

key (C7)

Consecutive

playback

(D6)

1st song 10th song 20th song 30th song 40th song 50th song (C



Listening to Songs Loaded from the Computer

CLP-320 Owner’s Manual

ENGLISH

Listening to Songs Loaded from the

Computer

You can transfer song data from your computer to this instrument and play back the songs. (See

page 31 for more information on loading song data from the computer.)

1. Select and play back a song.

You can load up to 10 songs or

up to 337 KB of data from the

computer.

Songs loaded from the com-

puter will be numbered auto-

matically.

Use the following table to write

down the song titles you loaded

from the computer.

Song numbers (1 through 10) are assigned to the D



6–C7 keys (see the illustra-

tion below).

While holding down the [DEMO/SONG] button, press one of the D



6–C7 keys

to select a song to play back.

The selected song starts to play.

Adjusting the Volume

Use the [MASTER VOLUME] control to adjust the volume while listening to the

song.

2. Stop playback.

To stop the song during playback, press the [DEMO/SONG] button.

Selecting a Song Playback Channel

If a song loaded from the computer uses a voice that is not supported by this

instrument, the originally-assigned voice may not be reproduced accurately. In

this case, switching the song playback channel from “All” to “1 + 2” may

improve the tone to more natural sound.

Selecting 1 + 2 song playback channels:

While pressing and holding down the

[DEMO/SONG] button and the [PIANO/

VOICE]

button simultaneously, press the C7 key.

Channels 1 + 2 will produce the sound.

Selecting all song playback channels:

While pressing and holding down the [DEMO/SONG] button and the [PIANO/

VOICE]

button simultaneously, press the B6 key.

All channels 1 through 16 will produce the sound.

Procedure

Key Song title



D 6



1st song 10th song

(The highest key)

The highest key

Selecting & Playing Voices

CLP-320 Owner’s Manual

ENGLISH

Selecting & Playing Voices

Selecting Voices

To understand the characteris-

tics of various voices, listen to

demo songs for each voice

(page 15).

Press and release the [PIANO/VOICE] button to select the Grand Piano 1 voice.

Press and release the [PIANO/VOICE] button, press the [+] or [–] button to select a dif-

ferent voice.

Selecting a voice automatically

engages the best-suited reverb

type and depth (page 20) for

that particular voice.

If you wish to select a particular voice directly, press and hold down the [PIANO/

VOICE]

button, then press one of the C1–A1 keys.

Turn the [MASTER VOLUME] control to adjust the volume level while playing the key-

board.

Procedure

Voice:

On this instrument, a voice

means a “tone” or “tonal

color.”

Key Voice Name Description

C1 Grand Piano 1 Recorded samples from a full concert grand piano. Perfect for classical

compositions as well as any other style that requires acoustic piano.



1Grand Piano 2 Spacious and clear piano with bright reverb. Good for popular music.

D1 E.Piano 1

An electronic piano sound created by FM synthesis. Good for popular music.



1 E.Piano 2 The sound of an electric piano using hammer-struck metallic “tines.” Soft

tone when played lightly, and an aggressive tone when played hard.

E1 Harpsichord 1 The deﬁnitive instrument for baroque music. Since the strings of a harpsi-

chord are plucked, there is no touch response.

F1 Harpsichord 2 Mixes the same voice an octave higher for a more brilliant tone.



1 Vibraphone The sound of a vibraphone played with relatively soft mallets.

G1 Church Organ 1 This is a typical pipe organ sound (8 feet + 4 feet + 2 feet). Good for

sacred music from the Baroque period.



1 Church Organ 2 This is the organ’s full coupler sound, often associated with Bach’s “Toc-

cata and Fugue”.

A1 Strings Spacious and large-scale string ensemble. Try combining this voice with

piano in DUAL mode.

C1 D1 E1 F1 G1 A1

C 1



D 1



F 1



G 1



The lowest key

Selecting & Playing Voices

CLP-320 Owner’s Manual

ENGLISH

Using the Pedals

If the damper pedal doesn’t

work, make sure that the pedal

cord is properly plugged into the

main unit (page 36).

Organ and string voices will

continue to sound for as long as

the sostenuto pedal is

depressed.

Damper (Right) Pedal

The damper pedal functions in the same way as a

damper pedal on an acoustic piano. When the

damper pedal is pressed, notes sustain longer.

Releasing the pedal immediately stops (damps) any

sustained notes.

The damper pedal features a half-pedal function.

Sostenuto (Center) Pedal

If you play a note or chord on the keyboard and

press the sostenuto pedal while the note(s) are

held, those notes will sustain as long as you hold

the pedal (as if the damper pedal had been pressed)

but all subsequently played notes will not be sus-

tained. This makes it possible to sustain a chord,

for example, while other notes are played “stac-

cato.”

Soft (Left) Pedal

The soft pedal reduces the volume and slightly changes the timbre of notes played while

the pedal is pressed. The soft pedal will not affect notes that are already playing when it

is pressed.

What is the half-pedal

function?

This function allows the sus-

tain length to vary depend-

ing on how far the pedal is

pressed. The farther you

press the pedal, the more

the sound sustains.

For example, if you press the

damper pedal and all notes

you are playing sound a bit

murky and loud with too

much sustain, you can

release the pedal half way to

subdue the sustain (murki-

ness).

When you press the damper pedal

here, the notes you play before you

release the pedal sustain longer.















When you press the sostenuto pedal

here while holding the note, the note

will sustain as long as you hold the

pedal.















Selecting & Playing Voices

CLP-320 Owner’s Manual

ENGLISH

Adding Variations to the Sound – Reverb

This control enables you to select various digital reverb effects that add extra depth and expression

to the sound to create a realistic acoustic ambience.

While holding down the [PIANO/VOICE] button, press one of the C2–E2 keys to select

a reverb type.

Adjusting Reverb Depth

The default reverb type (includ-

ing OFF) and depth settings are

different for each voice.

depth 0: no effect

depth 20: maximum reverb

depth

Adjust the reverb depth for the selected voice by pressing one of the C3–G



4 keys while

holding down the [PIANO/VOICE] button. The depth range is from 0 through 20.

While holding down the [PIANO/VOICE] button, press the A4 key to set the reverb to

the depth most suitable for the selected voice.

Procedure

Key Reverb Type Description

C2 Room This setting adds a continuous reverb effect to the sound, similar to

the acoustic reverberation you would hear in a room.



2 Hall1 For a “bigger” reverb sound, use the HALL 1 setting. This effect simu-

lates the natural reverberation of a small-size concert hall.

D2 Hall2 For a truly spacious reverb sound, use the HALL 2 setting. This effect

simulates the natural reverberation of a large concert hall.



2 Stage Simulates the reverb of a stage environment.

E2 Off No effect is applied.

C2 D2 E2

C 2



D 2



The lowest key

The depth value increases as you press higher keys.

The lowest key C3: depth 0



4: depth 20

Selecting & Playing Voices

CLP-320 Owner’s Manual

ENGLISH

Layering Two Voices (Dual mode)

You can layer two voices and play them simultaneously to create a thicker and more supple sound.

You cannot assign the same

voice to Voice 1 and Voice 2

simultaneously in Dual mode.

Reverb in Dual Mode

The reverb type assigned to

Voice 1 will take priority. (If the

reverb assigned to Voice 1 is set

to OFF, the reverb assigned to

Voice 2 will be in effect.)

1. Engage Dual mode.

While holding down the [PIANO/VOICE] button, press two keys in the range of

C1through A1 simultaneously (or press and hold down one key, then press

another) to select the two desired voices.

Refer to “Selecting Voices” (page 18) for information on the voices that are

assigned to the keys.

The voice assigned to the lower key will be designated as Voice 1, and the voice

assigned to the higher key will be designated as Voice 2.

You can make the following settings for Voices 1 and 2 in Dual mode:

Setting the Octave

You can shift the pitch up and down in octave steps for Voice 1 and Voice 2 inde-

pendently. Depending on which voices you combine in Dual mode, the combi-

nation may sound better if one of the voices is shifted up or down an octave.

While holding down the [PIANO/VOICE] button, press one of the C5–F5 keys.

Setting the Balance

You can adjust the volume balance between two voices. For example, you can set

one voice as the main voice with a louder setting, and make the other voice softer.

While holding down the [PIANO/VOICE] button, press one of the F



5–F



6 keys.

A setting of “0” produces an equal balance between the two Dual mode voices.

Settings below “0” increases the volume of Voice 2 in relation to Voice 1, and set-

tings above “0” increases the volume of Voice 1 in relation to Voice 2.

2. Exit Dual mode and return to normal play mode.

While holding down the [PIANO/VOICE] button, press one of the C1–A1 keys.

Procedure

C5 key: –1 (Voice 1), C



5 key: 0 (Voice 1), D5 key: +1(Voice 1),



5 key: –1 (Voice 2), E5 key: 0 (Voice 2), F5 key: +1(Voice 2)

C1 A1

The lowest key

C5 F5

The highest key



F 6



-5

-6 -4 -2

+1 +3 +6

-3 -1 0 +2 +4 +5

The highest key

Selecting & Playing Voices

CLP-320 Owner’s Manual

ENGLISH

Transposition

The Clavinova’s Transpose function makes it possible to shift the pitch of the entire keyboard up or

down in semitone intervals up to a maximum of six semitones, and lets you easily match the pitch of

the keyboard to the range of a singer or other instruments.

For example, if you set the transposition amount to “5,” playing key C produces pitch F. In this way,

you can play a song as though it were in C major, and this instrument will transpose it to F major.

While holding down the [DEMO/SONG] and [PIANO/VOICE] buttons, press one of

the F



2–F



3 keys to set the desired amount of transposition.

[DEMO/SONG] + [PIANO/VOICE] + C3 key:

Plays normal keyboard pitch.

[DEMO/SONG] + [PIANO/VOICE] + B2 key (white key to the left of C3):

Tr ansposes the pitch down by one semitone.

[DEMO/SONG] + [PIANO/VOICE] + B



2 key (the ﬁrst black key to the left of C3):

Tr ansposes the pitch down a whole tone (two semitones).

[DEMO/SONG] + [PIANO/VOICE] + F



2 key:

Tr ansposes the pitch down by six semitones.

[DEMO/SONG] + [PIANO/VOICE] + C



3 key (black key to the right of C3):

Tr ansposes the pitch up by one semitone.

[DEMO/SONG] + [PIANO/VOICE] + D3 key (the ﬁrst white key to the right of C3):

Tr ansposes the pitch up a whole tone (two semitones).

[DEMO/SONG] + [PIANO/VOICE] + F



3 key:

Tr ansposes the pitch up by six semitones.

Fine-tuning the Pitch

You can ﬁne-tune the pitch of the entire instrument. This function is useful when you play the Clavi-

nova along with other instruments or CD music.

To tune up (in about 0.2Hz steps): Press and hold down the A–1, B–1 and C0

keys simultaneously, and press any key between C3 and B3.

To tune down (in about 0.2Hz steps): Press and hold down the A–1, B–1 and



0 keys simultaneously, and press any key between C3 and B3.

To restore standard pitch: Press and hold down the A–1, B–1, C0 and C



0 keys

simultaneously, and press any key between C3 and B3.

Setting range: 427.0–453.0 Hz

Standard pitch: 440.0 Hz

Procedure

Transpose:

Changing the key signature.

On this instrument, trans-

posing shifts the pitch of the

entire keyboard.

-5 -3 -1 0 +2 +4 +5

-6 -4 -2 +1

+3 +6



The lowest key

Transpose down. Transpose up.

Normal pitch.

Procedure

Hz (Hertz):

This unit of measurement

refers to the frequency of a

sound and represents the

number of times a sound

wave vibrates in a second.

C3 B3

C0B-1



A-1 C 0

B-1

A-1 C0

B-1

A-1 C 0

To tune up To tune down To restore standard pitch

Selecting & Playing Voices

CLP-320 Owner’s Manual

ENGLISH

Using the Metronome

The Clavinova features a built-in metronome (a device that keeps an accurate tempo) that is conve-

nient for practicing.

1. Start the metronome.

Press the [METRONOME] button to turn on the metronome.

Determines the Time Signature

While holding down the [METRONOME] button, press one of the C3–F3 keys.

C3 key: No downbeat, C



3 key: 2/4, D3 key: 3/4, D



3 key: 4/4, E3 key: 5/4,

F3 key: 6/4

Adjusting the Tempo

You can adjust the metronome tempo by pressing the [+] or [–] button while the

metronome is playing.

The tempo of the metronome and preset song playback can be set from 32 to

280 beats per minute.

A number is assigned to each of the following keys.

While holding down the [METRONOME] button, press a sequence of C4–A4

keys to specify a three-digit number.

Select a number starting from the left-most digit. For example, to set the tempo

“95,” press the C4 (0), A4 (9) and F4 (5) keys in sequence.

Increasing the tempo value in steps of one:

While the metronome is playing, press the [+] button. Alternatively, press and

hold down the [METRONOME] button, and press the C



5 key.

Decreasing the tempo value in steps of one:

While the metronome is playing, press the [–] button. Alternatively, press and

hold down the [METRONOME] button, and press the B4 key.

Increasing the tempo value in steps of ten:

Press and hold down the [METRONOME] button, and press the D5 key.

Decreasing the tempo value in steps of ten:

Press and hold down the [METRONOME] button, and press the A



4 key.

To reset the tempo to default

value of 120 while the metro-

nome is stopped, press the

[METRONOME], [+] and [–] but-

tons simultaneously.

Resetting the tempo to default:

While the metronome is playing, press the [+] and [–] buttons simultaneously.

Alternatively, press and hold down the [METRONOME] button, and press the

C5 key.

Procedure



The highest key

C4 A4F4

METRONOME

024579

8631



The highest key

Selecting & Playing Voices

CLP-320 Owner’s Manual

ENGLISH

Adjusting the Volume

You can change the volume of the metronome sound.

While holding down the [METRONOME] button, press one of the C1–G2 keys

to determine the volume.

2. Stop the metronome.

Turn off the metronome by pressing the [METRONOME] button.

Adjusting the Keyboard Touch (Touch Sensitivity)

This setting is disabled with

some voices, such as an organ

sound.

You can adjust the volume level, which changes depending on how fast

or strong you hit the keys (keyboard touch). Select an appropriate key-

board touch for the voices, songs or your taste.

While holding down the [PIANO/VOICE] button, press one of the A6–C7 keys to select

the desired touch sensitivity.

C1 G2

The volume level increases as you press higher keys.

The lowest key

Key

Touch

Sensitivity

Setting

Description

A6 Fixed The volume level does not change at all regardless of whether you play

the keyboard soft or hard.



6 Soft The volume level does not change much when you play the keyboard

soft or hard.

B6 Medium This is the standard piano touch response. (This is the default setting.)

C7 Hard The volume level changes very widely from pianissimo to fortissimo to

facilitate dynamic and dramatic expression. You have to hit the keys hard

to produce a loud sound.

Procedure

C7A6

Recording your Performance

CLP-320 Owner’s Manual

ENGLISH

Recording your Performance

The Clavinova’s recording function enables you to record your performance of one song.

The recorded performance is called the “user song.”

Follow the steps below to record and play back your performance.

The user song is saved as a

Standard MIDI ﬁle (SMF).

(page 31)

To transfer and play the user

song on another device, you

must have Musicsoft Down-

loader (page 31) installed on

your computer.

CAUTION

Be careful not to erase the recorded data:

After you record a performance on this instrument, the [PLAY] button indicator lights

up. When this indicator remains on, recording another performance will erase the

recorded data.

You cannot engage Record mode

while a demo song is playing.

Recording capacity

“Recording capacity” is the

maximum amount of perfor-

mance data that you can

record. This instrument’s

recording capacity is 100 KB

(approximately 11,000 notes).

Changing the settings for the

recorded user song

If you wish to change the voice

of the user song, before press-

ing the [REC] button, select a

different voice. Then, press the

[REC] button to engage Record

mode. Without playing the key-

board, press the [REC] button

again to apply the change to the

song. If you wish to change the

tempo, do so after you engage

Record mode.

You can save the recorded user

song to a computer. You can

also load the user song data

from a computer and play it back

on this instrument. (See

page 31.)

1. Select a voice and other settings for the recording.

While holding down the [PIANO/VOICE] button, press one of the C1–A1 keys

to select the desired voice(s). (See page 18.)

If you desire, you can select other settings, such as the reverb setting.

Use the [MASTER VOLUME] control to adjust the volume to a comfortable lis-

tening level. You can also use the [MASTER VOLUME] control to adjust the vol-

ume level during playback.

2. Engage Record mode.

Press the [REC] button.

The [REC] button indicator ﬂashes. (It may take a moment before the

indicator starts to ﬂash.)

Press the [REC] button again if you wish to cancel Record mode.

3. Start recording.

Recording starts as soon as you play the keyboard.

Alternatively, press the [PLAY] button to start recording.

The [REC] button indicator lights up steadily, and the [PLAY] button indi-

cator ﬂashes at the current tempo.

4. Stop recording.

Press the [REC] button.

CAUTION

Do not turn off the power to this instrument while it is recording the data in its internal

memory (that is, while the [REC] and [PLAY] button indicators are ﬂashing). Otherwise,

all recorded data, including the data being recorded, will be lost.

Audio recording and data recording

Cassette tape recordings use a different data format than this instrument. Cassette

tapes record audio signals. On the other hand, this instrument records information

about the notes and voices being played and about the timing and tempo of those

notes. It does not record audio signals. When you play back a recorded performance

on this instrument, its internal tone generator reproduces the sound according to

the recorded information.

Procedure

Recording your Performance

CLP-320 Owner’s Manual

ENGLISH

Playing Back Recorded Performance Data

1. Start the playback.

While the user song is playing,

press and hold down the [MET-

RONOME] button and press the

[+] or [–] button to change the

song tempo.

If you are using the metronome

(page 23) during demo song

playback, press the [+] or [–]

button to change the song

tempo.

You can also press keys to

change the tempo. (page 23)

Press the [PLAY] button.

The [PLAY] button indicator ﬂashes at the current tempo.

2. Stop the playback.

When the user song ﬁnishes playing back, this instrument automatically returns

to the previous mode.

To stop the playback, press the [PLAY] button.

Erasing Recorded Performance Data

You can erase the recorded user song.

1. Engage Record mode.

Press the [REC] button.

To cancel the erase operation,

press the [REC] button again.

The [REC] button indicator ﬂashes.

2. Erase the song.

Please note that even after you

cancel the erase operation, the

user song settings, including the

voice selection, will automati-

cally return to the status

obtained at the time you

engaged Record mode.

(page 25)

Press and hold down the [PLAY] button, then press the [REC] button.

The recorded user data is erased.

Procedure

Connecting MIDI Instruments

CLP-320 Owner’s Manual

ENGLISH

Connecting MIDI Instruments

Since the transmission or

reception of MIDI data can vary

depending on the type of MIDI

device, each MIDI device can

transmit or receive only data

and commands that are com-

patible with other connected

MIDI devices.

Please check the “MIDI Imple-

mentation Chart” on the web

(please refer to “Data List” on

page 6) to ﬁnd out what MIDI

data and commands your

devices can transmit or receive.

You need a dedicated MIDI

cable (optional) to make a MIDI

connection. You can purchase

MIDI cables at musical instru-

ment stores.

If you connect a very long MIDI

cable, data transmission errors

may result. Use a MIDI cable of

15 meters or less.

Before connecting a MIDI

device to this instrument, ﬁrst

turn off the power to both this

instrument and the MIDI device.

After connecting them, turn on

the power to the MIDI device

ﬁrst, then turn on the power to

this instrument.

The Clavinova features MIDI connectors. Using the MIDI functions

enables you to access a variety of musical genres.

About MIDI

MIDI (Musical Instrument Digital Interface) is a global format standard

for performance data transmission and reception between electronic

musical instruments.

Connecting musical instruments that support MIDI via MIDI cables

enables you to transfer performance and setting data between multiple

musical instruments. Using MIDI, you can also achieve more advanced

performances than using just a single musical instrument.

MIDI’s Capability

MIDI functions enable you to transfer performance data between MIDI

devices, load song data from a connected computer to your instru-

ment, and transmit and save user song data to a computer.

You cannot transmit the voice

demo songs and the 50 piano

preset songs from this instru-

ment to another MIDI device.

● Transferring performance data to and from another MIDI device

For more information on the

transmission and reception of

song data, refer to “Transmitting

Song Data between the Com-

puter and the Clavinova” on

page 31.

● Transferring MIDI data to and from a computer

MIDI

INOUT

POWER

MIDI IN

connector

MIDI OUT

connector

MIDI IN

connector

MIDI OUT

connector

Optional

MIDI cables

MIDI instrument

OUT

POWER

MIDI IN

connector

MIDI OUT

connector

Computer

UX16 (optional)

USB port

Connecting a Computer

CLP-320 Owner’s Manual

ENGLISH

Connecting a Computer

Connecting the instrument to a computer using the MIDI connectors enables you to transfer MIDI

data between the instrument and the computer. This connection requires that you have appropri-

ate application software installed on the computer.

Also, installing Musicsoft Downloader on the computer enables you to transfer song data between

the piano and the computer. (page 31)

When this instrument is used as a tone module, performance data with voices that are not found on this instrument will

not be played correctly.

Before you connect this instrument to a computer, ﬁrst turn off the power to both this instrument and the computer.

After you make the connections, turn on the power to the computer ﬁrst, then turn on the power to this instrument.

An example of connecting this instrument to the USB port on a computer

Use an optional USB-MIDI interface (such as a Yamaha UX16) to connect this instrument’s MIDI connectors to the com-

puter’s USB port.

You must install the USB-MIDI driver on the computer correctly so that you can control your MIDI instrument from the

computer. The USB-MIDI driver is a software application that enables MIDI signals to be transmitted between the

sequence software on the computer and the connected MIDI instrument. For more information, refer to the user’s man-

ual that came with the USB interface device.

Connecting this instrument to the computer using a USB-MIDI interface

Tu rn off the power to this instrument. Connect the MIDI OUT cable from the USB-MIDI interface to this instru-

ment’s MIDI IN connector, and connect the MIDI IN cable from the USB-MIDI interface to this instrument’s MIDI

OUT connector.

The connection between this instrument and the computer has now been established.

Turn on the power to this instrument and try to transfer MIDI data to or from the computer.

For more information on connecting the UX16, refer to the user’s manual that came with the UX16.

You must install a software application on the computer to be able to transfer MIDI data between this instrument and a

computer.

OUT

MIDI

INOUT

POWER

Computer

MIDI Functions

CLP-320 Owner’s Manual

ENGLISH

MIDI Functions

You can make detailed adjustments to MIDI settings.

MIDI Transmit/Receive Channel Selection

In Dual mode, Voice 1 data is

transmitted on its speciﬁed

channel and Voice 2 data is

transmitted on the next greater

channel number relative to the

speciﬁed channel. In this mode,

no data is transmitted if the

transmit channel is set to “OFF.”

MIDI receive channel is ALL:

A “Multi-timbre” Receive mode

is available. In this mode, this

instrument receives different

parts from the connected MIDI

device on any or all 16 MIDI

channels and plays multi-chan-

nel song data.

MIDI receive channel is 1+2:

A “1+2” Receive mode is avail-

able. It allows simultaneous

reception on channels 1 and 2

only, enabling this instrument to

play 1 and 2 channel song data

received from a music computer

or sequencer.

Program change and other like

channel messages received will

not affect this instrument’s

panel settings or the notes you

play on the keyboard.

Data for the demo song and 50

piano preset songs cannot be

transmitted via MIDI.

CAUTION

When Local control is turned

OFF, the keyboard of this instru-

ment does not play the internal

voices.

In any MIDI control setup, the MIDI channels of the transmitting and receiving equip-

ment must be matched for proper data transfer.

This parameter enables you to specify the channel on which the instrument transmits

or receives MIDI data.

Setting the transmit channel

While holding down the [DEMO/SONG] and [PIANO/VOICE] buttons simultaneously,

press one of the C1–E2 keys.

Setting the receive channel

While holding down the [DEMO/SONG] and [PIANO/VOICE] buttons simultaneously,

press one of the C4–F5 keys.

Local Control ON/OFF

“Local Control” refers to the fact that, normally, the keyboard of this instrument con-

trols its internal tone generator, allowing the internal voices to be played directly from

the keyboard. This situation is “Local Control On,” since the internal tone generator is

controlled locally by its own keyboard.

Local control can be turned OFF, however, so that the keyboard of this instrument does

not play the internal voices, but the appropriate MIDI information is still transmitted

via the MIDI OUT connector when notes are played on the keyboard. At the same

time, the internal tone generator responds to MIDI information received via the MIDI

IN connector.

While holding down the [DEMO/SONG] and [PIANO/VOICE] buttons simultaneously,

press the C6 key. Pressing the C6 key repeatedly toggles between Local Control On and

Off.

Procedure

C1 C4 F5

OFF



1356810

24 7911 14 16

12 13 15

ALL

1356810

24 7911 14 16

12 13 15

1+2



(C1–D

(C4–F5)

For setting the

transmit channels.

For setting the

receive channels.

The highest key

MIDI Functions

CLP-320 Owner’s Manual

ENGLISH

Program Change ON/OFF

For information on program

change numbers for each voice,

check the MIDI Data Format on

the web (please refer to “Data

List” on page 6).

Normally this instrument will respond to MIDI program change numbers received

from an external keyboard or other MIDI device, causing the correspondingly-num-

bered voice to be selected on the corresponding channel (the keyboard voice does not

change). This instrument will normally also send a MIDI program change number

whenever one of its voices is selected, causing the correspondingly-numbered voice or

program to be selected on the external MIDI device if the device is set up to receive and

respond to MIDI program change numbers.

This function makes it possible to cancel program change number reception and trans-

mission so that voices can be selected on this instrument without affecting the external

MIDI device.

While holding down the

[DEMO/SONG] and [PIANO/VOICE] buttons simultaneously,

press the C



6 key. Pressing the C



6 key repeatedly toggles between Program Change On

and Off.

Control Change ON/OFF

For information on control

changes that can be used with

this instrument, check the MIDI

Data Format on the web (please

refer to “Data List” on page 6).

MIDI Control Change data refers to MIDI information related to performance expres-

sion (such as damper pedal information).

You can transmit MIDI Control Change data from this instrument to control the oper-

ation of the connected MIDI device. (For example, if you operate this instrument’s

damper pedal, this instrument will transmit MIDI Control Change data.)

On the other hand, MIDI performance data of this instrument will respond to MIDI

Control Change data received from the connected MIDI device. (At this time, the voice

you are playing on the keyboard will not be affected by the Control Change data.)

The ability to transmit and receive MIDI Control Change data is sometimes very use-

ful. Turn Control Change On if it is convenient for you to have this capability. Turn

Control Change Off if you rather prefer not to have this capability.

While holding down the [DEMO/SONG] and [PIANO/VOICE] buttons simultaneously,

press the D6 key. Pressing the D6 key repeatedly toggles between Control Change On

and Off.

Procedure



The highest key

Procedure

The highest key

Transmitting Song Data between the Computer and the Clavinova

CLP-320 Owner’s Manual

ENGLISH

Transmitting Song Data between the

Computer and the Clavinova

You can download free Music-

soft Downloader from the

Yamaha website.

In addition to the demo songs and the 50 piano preset songs stored in this instrument,

you can play data for other song by loading it from a connected computer.

To be able to use this function, you must ﬁrst download Musicsoft Downloader from

Yamaha website at the following URL, and install it on your computer.

http://music.yamaha.com/download/

Do not manually change the ﬁle

name by using a computer;

doing so will render the ﬁle

unable for loading on the instru-

ment.

● System requirement for Musicsoft Downloader

Loading Song Data from a Computer

to the Clavinova

You can load piano song data from a computer to this instrument. Also, after you

record your performance on this instrument and save the recording to a computer, you

can load the recording back to the instrument.

This instrument can read MIDI data in SMF Format 0. However, if such data includes

any information for functions that are not supported by this instrument, the instru-

ment will not play the data correctly.

For more information on loading song data from a computer to this instrument, please

refer to “Transferring Data Between the Computer and Instrument (for unprotected

data)” in the Help ﬁle that came with Musicsoft Downloader.

● Requirements for song data that can be loaded from a computer to this

instrument

Song data loaded from a com-

puter or User song data will be

saved in the internal ﬂash mem-

ory.

While Musicsoft Downloader is

operating, the [REC] and

[PLAY] button indicators on the

piano light up.

Before you use this instrument,

close the Musicsoft Downloader

window and quit the application.

You can play the loaded Songs. (page 17)

CAUTION

Do not turn off the power to this instrument or unplug the instrument during data

transmission. Otherwise, the data being transmitted will not be saved. Furthermore,

ﬂash memory operation may become unstable, causing the entire memory to be

erased when you turn the power to the instrument on or off.

• OS

• CPU

• Memory

• Available hard

disk capacity

• Display

• Others

Windows 2000/XP Home Edition/XP Professional/Vista

* For XP and Vista, the 32-bit version is supported, but not

the 64-bit version.

Intel® Pentium® or Celeron® chip of 500MHz or higher

256MB or higher

128MB or higher (512MB or higher recommended)

800 × 600 High Color (16-bit)

Microsoft® Internet Explorer® version 5.5 or higher

SMF (Standard MIDI File)

This ﬁle features a popular

sequence format (for record-

ing performance data). This

ﬁle is sometimes called a

“MIDI ﬁle.” The ﬁle exten-

sion is MID.

You can play the SMF format

song using music software

or a sequencer that supports

SMF. This instrument also

supports SMF.

•Number of songs : Up to 10 songs plus one user song

•Maximum data size : 337KB plus 100KB(user)

• Data format : SMF Format 0

Transmitting Song Data between the Computer and the Clavinova

CLP-320 Owner’s Manual

ENGLISH

Transmitting Song Data from the

Clavinova to a Computer

Musicsoft Downloader enables you to transfer the user song in this instrument to a

computer. For more information on transferring song data from this instrument to a

computer, please refer to “Transferring Data Between the Computer and Instrument

(for unprotected data)” in the Help ﬁle that came with Musicsoft Downloader.

If you rename the song ﬁle

“USERSONG1.MID,” the instru-

ment will be unable to recognize

the ﬁle.

● Data you can transfer from this instrument to a computer

Backing up Data and Initializing the

Settings

Backing up data to ﬂash memory

Backup data for metronome vol-

ume and time signature, touch

sensitivity,tuning, and user song

is included in the ﬁle named

“08CLP-L.BUP” and stored in

this instrument. You can transfer

the backup data between the

instrument and a computer.

The following items will be stored in ﬂash memory on this instrument. This data will

be kept after you turn off the power to the instrument.

Initializing the settings

If this instrument somehow

becomes disabled or malfunc-

tions, turn off the power to the

instrument, then perform the ini-

tialization procedure.

When you initialize the settings, all data, excluding the songs loaded from a computer,

will be initialized and reset to the factory default settings.

CAUTION

Please note that initializing the settings will delete your recorded song (user song).

While holding down the C7 (the highest) key, turn on the power to the instrument.

The data (excluding the data for the songs loaded from a computer) will be

initialized.

CAUTION

Do not turn off the power to this instrument while it is initializing the data in its internal

memory (that is, while the [REC] and [PLAY] button indicators are ﬂashing).

•User song : USERSONG1.MID

•Back up data : 08CLP-L.BUP

•Song data (once it has been loaded from the computer)

Backup data

Metronome volume

Metronome time signature

Touch sensitivity

Tuning

Recorded performance data (user song)

Song data once loaded from a computer

The highest key

Troubleshooting

CLP-320 Owner’s Manual

ENGLISH

Troubleshooting

Options

BC-100 Bench

A comfortable bench styled to match your Yamaha Clavinova.

UX16

USB-MIDI interface

HPE-160

Headphones

Problem Possible Cause and Solution

This instrument does not turn on. This instrument has not been plugged in properly. Securely insert the female plug into

the socket on this instrument, and the male plug into a proper AC outlet (page 13).

Noise from the speakers or headphones is

audible.

The noise may be due to interference caused by the use of a mobile phone in close

proximity to this instrument. Turn off the mobile phone, or move it further away from

this instrument.

The overall volume is low, or no sound is

heard.

• The Master Volume is set too low. Set it to an appropriate level using the [MASTER

VOLUME] control.

• Make sure a pair of headphones is not connected to the headphones jack.

• Make sure that Local Control (page 29) is ON.

The damper pedal has no effect. The pedal cord may not be properly connected. Make sure to securely insert the pedal

cord into the [PEDAL] jack (page 36).

Keyboard Stand Assembly

CLP-320 Owner’s Manual

ENGLISH

Keyboard Stand Assembly

CAUTION

• Be careful not to confuse parts, and be sure to install all parts in the correct direction. Please assemble in accor-

dance with the sequence given below.

• Assembly should be carried out by at least two persons.

• Assemble the stand on the ﬂat ﬂoor surface.

• Be sure to use the included screws only, and insert screws of the correct size in the correct hole locations. Use of

incorrect screws can cause damage or malfunction of the product.

• Be sure to tighten up all screws upon completing assembly of each unit.

•To disassemble, reverse the assembly sequence given below.

Remove all parts from the package and make sure you

have all of the items.

1. Attach (ﬁnger-tighten) C to D

and E.

1-1 Untie and straighten out the bundled pedal

cord. Don’t discard the vinyl tie. You will

need it later in step 6.

1-2 Align D and E with each end of C.

1-3 Attach D and E to C by ﬁnger-tightening the

long screws 1 (6 × 20mm).

Have a Phillips-head (+) screwdriver of the

appropriate size ready.

Bundled pedal cord

inside

AC Power cord

Assembly Parts

20 mm long screws

6 × 16 mm short screws ×4

4 × 12 mm thin screws ×2

4 × 20 mm tapping screws

Cord holders × 2

Headphone hanger set

4 × 10 mm thin screws ×2 5 Headphone hanger

1-2

1-1

1-3

Keyboard Stand Assembly

CLP-320 Owner’s Manual

ENGLISH

2. Attach B.

Depending on the model of Clavinova you pur-

chased, the surface color of one side of B may be

different from the other side. In this case, position

B so that the side of the surface color similar to D

and E faces the player.

2-1 Place the lower side of B on each foot of D

and E, then attach the upper side to D and

2-2 Attach the top of B to D and E by ﬁnger-

tightening the thin screws 3 (4 × 12mm).

2-3 While pushing the lower part of D and E

from outside, secure the bottom ends of B

using two tapping screws 4 (4 × 20mm).

2-4 Insert the other two tapping screws 4 (4 ×

20mm) into the other two screw holes to

secure B.

2-5 Securely tighten the screws on the top of B

that were attached in Step 2-2.

3. Securely tighten the screws on C

that were attached in Step 1-3.

4. Mount A.

5. Secure A.

5-1 Adjust the position of A so that the left and

right ends of A will project beyond D and E

equally when seen from the front.

5-2 Secure A by tightening the short screws 2

(6 × 16mm) from the front.

2-2, 2-5

2-4

2-3

2-1

2-3

Place the bot-

tom ends of the

rear panel on

each foot.

Be sure to place your hands at

least 10 cm from either end of the

main unit when positioning it.

At least

10 cm

CAUTION

•

Fingers can become pinched between the main

unit and the rear or side panels, be extra careful

so as not to drop the main unit.

•

Do not hold the keyboard in any position other

than the position shown in the illustration.

5-1

5-2

Projection

of A

Keyboard Stand Assembly

CLP-320 Owner’s Manual

ENGLISH

6. Connect the pedal cord.

6-1 Insert the pedal cord plug to the pedal con-

nector from the rear.

6-2 Attach the cord holders to the rear panel as

shown, then clip the cord into the holders.

6-3 Use a vinyl tie to take up any slack in the

pedal cord.

7. Connect the power cord to the

unit.

7-1 Set the voltage selector (for models that fea-

ture a voltage selector).

7-2 Connect the plug on the power cord to the

rear panel connector.

WARNING

An improper voltage setting can cause serious damage to

this instrument or result in improper operation.

8. Set the adjuster.

9. Attach the headphone hanger.

Use the included two screws 5 (4 × 10mm) to

attach the hanger as shown in the illustration

below.

Voltage Selector

Before connecting the AC power cord, check the set-

ting of the voltage selector which is provided in some

areas. To set the selector for 110V, 127V, 220V or 240V

main voltages, use a “minus” screwdriver to rotate the

selector dial so that the correct voltage for your region

appears next to the pointer on the panel. The voltage

selector is set at 240V when the unit is initially

shipped. After the proper voltage has been selected,

connect the AC power cord to the AC IN and an AC

wall outlet. A plug adaptor may be also provided in

some areas to match the pin conﬁguration of the AC

wall outlets in your area.

LET

PEDAL

6-1

6-3

6-2

240

127

110

220

Rotate the adjuster until it comes in ﬁrm contact with the

ﬂoor surface.

PHONES

Keyboard Stand Assembly

CLP-320 Owner’s Manual

ENGLISH

After completing the assembly, please

check the following.

When moving the instrument after assembly, always

hold the bottom of the main unit.

CAUTION

Do not hold the key cover or top portion. Improper

handling can result in damage to the instrument or

personal injury.

•

Are there any parts left over?

→ Review the assembly procedure and correct any

errors.

•

Is this instrument clear of doors and other mov-

able ﬁxtures?

→ Move the instrument to an appropriate location.

•

Does this instrument make a rattling noise when

you shake it?

→ Tighten all screws.

•

Does the pedal box rattle or give way when you

step on the pedals?

→ Tu rn the adjuster so that it is set ﬁrmly against

the ﬂoor.

•

Are the pedal and power cords inserted securely

into the sockets?

→ Check the connection.

•

If the main unit creaks or is otherwise unsteady

when you play on the keyboard, refer to the

assembly diagrams and retighten all screws.

Key cover

Top portion

Do not

hold here.

Hold here.

Do not

hold here.

Index

CLP-320 Owner’s Manual

ENGLISH

Index

Symbols

+/–....................................................................................10

Numerics

50 Piano Preset Songs .....................................................16

Accessories.........................................................................7

AC IN...............................................................................11

Adjust

Keyboard Touch........................................................24

Reverb Depth.............................................................20

Tempo (metronome) ................................................23

Volume (metronome)...............................................24

Assembly....................................................................34–37

AWM..................................................................................8

AWM Dynamic Stereo Sampling .....................................8

Center Pedal ....................................................................19

Computer.........................................................................28

Connecting a Computer .................................................28

Control Change ...............................................................30

Damper Pedal ..................................................................19

DEMO/SONG .....................................................10, 15–17

Dual mode .......................................................................21

Half-pedal ........................................................................19

Headphone ......................................................................14

Headphone hanger....................................................14, 36

Initializing the Settings ...................................................32

Keyboard Stand .........................................................34–36

Key Cover ........................................................................12

Layering Two Voices (Dual mode) ................................ 21

Left Pedal......................................................................... 19

Local Control ..................................................................29

MASTER VOLUME..................................................10, 14

METRONOME ......................................................... 10, 23

MIDI ................................................................................ 27

MIDI cables .....................................................................27

MIDI connectors....................................................... 27, 28

MIDI Data Format............................................................6

MIDI Implementation Chart ...........................................6

MIDI IN/OUT..................................................... 11, 27, 28

Music Rest .......................................................................12

Musicsoft Downloader ...................................................31

PEDAL ................................................................. 11, 19, 36

PHONES.................................................................... 10, 14

PIANO/VOICE .........................................................10, 18

PLAY.......................................................................... 10, 26

Playing Back Recorded Performance Data....................26

POWER ..................................................................... 10, 13

Preset songs ➝ 50 Piano Preset Songs...........................16

Program Change .............................................................30

REC............................................................................10, 25

Recording your Performance .........................................25

Reverb..............................................................................20

Right Pedal ......................................................................19

SMF..................................................................................31

Soft Pedal.........................................................................19

Song .................................................................................16

Song Playback Channel ..................................................17

Sostenute Pedal ...............................................................19

Stand ..........................................................................34–36

Standard MIDI File.........................................................31

Index

CLP-320 Owner’s Manual

ENGLISH

Start/Stop playback

50 Piano Preset Songs................................................16

Demo Songs...............................................................15

Tempo..............................................................................23

Touch Sensitivity.............................................................24

Transmitting Song Data..................................................31

Transporting......................................................................7

Transposition ..................................................................22

Troubleshooting..............................................................33

User Song.........................................................................25

Voice ................................................................................18

Specifications / Technische Daten / Caractéristiques techniques / Especificaciones

CLP-320

Owner’s Manual

Speciﬁcations / Technische Daten /

Caractéristiques techniques /

Especiﬁcaciones

*Speciﬁcations and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right to change

or modify products or speciﬁcations at any time without prior notice. Since speciﬁcations, equipment or options may not be the

same in every locale, please check with your Yamaha dealer.

*Die technischen Daten und Beschreibungen in dieser Bedienungsanleitung dienen nur der Information. Yamaha Corp. behält sich

das Recht vor, Produkte oder deren technische Daten jederzeit ohne vorherige Ankündigung zu verändern oder zu modiﬁzieren. Da

die technischen Daten, das Gerät selbst oder Sonderzubehör nicht in jedem Land gleich sind, setzen Sie sich im Zweifel bitte mit

Ihrem Yamaha-Händler in Verbindung.

*Les caractéristiques techniques et les descriptions du mode d’emploi ne sont données que pour information. Yamaha Corp. se

réserve le droit de changer ou modiﬁer les produits et leurs caractéristiques techniques à tout moment sans aucun avis. Du fait que

les caractéristiques techniques, les équipements et les options peuvent différer d’un pays à l’autre, adressez-vous au distributeur

Yamaha le plus proche.

* Las especiﬁcaciones y descripciones de este manual del propietario tienen sólo el propósito de servir como información. Yamaha

Corp. se reserva el derecho a efectuar cambios o modiﬁcaciones en los productos o especiﬁcaciones en cualquier momento sin previo

aviso. Puesto que las especiﬁcaciones, equipos u opciones pueden no ser las mismas en todos los mercados, solicite información a su

distribuidor Yamaha.

Appendix/Anhang/Annexe/Apéndice

CLP-320

Keyboard

GH(Graded Hammer) keyboard

Number of keys

88keys (A-1–C7)

Touch

Hard/Medium/Soft/Fixed

Sound Source

AWM Dynamic Stereo Sampling

Polyphony

128 Notes Max.

Voice Selection

Effect

Reverb

Volume

Master Volume

Controls

Dual, Metronome, Transpose

Pedal

Damper (with half-pedal effect), Sostenuto, Soft

Demo Songs

10 Demo Songs, 50 Piano Preset Songs

Recording Function

One Song 100KB (approx.11,000 notes)

Recording/Playback Format

Standard MIDI File (SMF) Format 0

Loading song data from a computer

Up to 10 songs; Total maximum size 337KB

Jacks/Connectors

MIDI (IN/OUT), PHONES

Main Ampliﬁers

20W

Speakers

Oval (12 cm

6 cm)

Dimensions (W

[For models with polished ﬁnish]

1387 mm

424 mm

818 mm (54-5/8"

16-11/16"

32-1/4")

[1388 mm

424 mm

822 mm (54-5/8"

16-11/16"

32-3/8")]

Dimensions (W

With music rest

[For models with polished ﬁnish]

1387 mm

424 mm

972 mm (54-5/8"

16-11/16"

38-1/4")

[1388 mm

424 mm

974 mm (54-5/8"

16-11/16"

38-3/8")]

Weight

[For models with polished ﬁnish]

46 kg (101 lbs., 7 oz)

[49 kg (108 lbs.)]

Accessories

Owner’s Manual, “50 greats for the Piano” (Music Book), Quick Operation Guide,

Bench (included or optional depending on locale)

AC Power Cord

146

Appendix

CLP-320 Owner’s Manual

MEMO

147

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)

(2 wires)

• This applies only to products distributed by Yamaha Music U.K.

Ltd.

FCC INFORMATION (U.S.A.)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instruc-

tions contained in this manual, meets FCC require-

ments. Modiﬁcations not expressly approved by

Yamaha may void your authority, granted by the FCC, to

use the product.

2. IMPORTANT: When connecting this product to acces-

sories and/or another product use only high quality

shielded cables. Cable/s supplied with this product

MUST be used. Follow all installation instructions. Fail-

ure to follow instructions could void your FCC authoriza-

tion to use this product in the USA.

3. NOTE: This product has been tested and found to com-

ply with the requirements listed in FCC Regulations,

Part 15 for Class “B” digital devices. Compliance with

these requirements provides a reasonable level of

assurance that your use of this product in a residential

environment will not result in harmful interference with

other electronic devices. This equipment generates/

uses radio frequencies and, if not installed and used

according to the instructions found in the users manual,

may cause interference harmful to the operation of

other electronic devices. Compliance with FCC regula-

tions does not guarantee that interference will not occur

in all installations. If this product is found to be the

source of interference, which can be determined by

turning the unit “OFF” and “ON”, please try to eliminate

the problem by using one of the following measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line ﬁlter/s.

In the case of radio or TV interference, relocate/reorient

the antenna. If the antenna lead-in is 300 ohm ribbon

lead, change the lead-in to co-axial type cable.

If these corrective measures do not produce satisfac-

tory results, please contact the local retailer authorized

to distribute this type of product. If you can not locate

the appropriate retailer, please contact Yamaha Corpo-

ration of America, Electronic Service Division, 6600

Orangethorpe Ave, Buena Park, CA90620

The above statements apply ONLY to those products

distributed by Yamaha Corporation of America or its

subsidiaries.

IMPORTANT NOTICE FOR THE UNITED KINGDOM

Connecting the Plug and Cord

IMPORTANT. The wires in this mains lead are coloured in

accordance with the following code:

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead of this appa-

ratus may not correspond with the coloured makings iden-

tifying the terminals in your plug proceed as follows:

The wire which is coloured BLUE must be connected to

the terminal which is marked with the letter N or coloured

BLACK.

The wire which is coloured BROWN must be connected to

the terminal which is marked with the letter L or coloured

RED.

Making sure that neither core is connected to the earth ter-

minal of the three pin plug.

148

For details of products, please contact your nearest Yamaha

representative or the authorized distributor listed below.

Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou

au distributeur le plus proche de vous ﬁgurant dans la liste suivante.

Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten

Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen

Bestimmungsländern erhältlich.

Para detalles sobre productos, contacte su tienda Yamaha más cercana

o el distribuidor autorizado que se lista debajo.

CANADA

Yamaha Canada Music Ltd.

135 Milner Avenue, Scarborough, Ontario,

M1S 3R1, Canada

Tel: 416-298-1311

U.S.A.

Yamaha Corporation of America

6600 Orangethorpe Ave., Buena Park, Calif. 90620,

U.S.A.

Tel: 714-522-9011

MEXICO

Yamaha de México S.A. de C.V.

Calz. Javier Rojo Gómez #1149,

Col. Guadalupe del Moral

C.P. 09300, México, D.F., México

Tel: 55-5804-0600

BRAZIL

Yamaha Musical do Brasil Ltda.

Rua Joaquim Floriano, 913 - 4' andar, Itaim Bibi,

CEP 04534-013 Sao Paulo, SP. BRAZIL

Tel: 011-3704-1377

ARGENTINA

Yamaha Music Latin America, S.A.

Sucursal de Argentina

Viamonte 1145 Piso2-B 1053,

Buenos Aires, Argentina

Tel: 1-4371-7021

PANAMA AND OTHER LATIN

AMERICAN COUNTRIES/

CARIBBEAN COUNTRIES

Yamaha Music Latin America, S.A.

Torre Banco General, Piso 7, Urbanización Marbella,

Calle 47 y Aquilino de la Guardia,

Ciudad de Panamá, Panamá

Tel: +507-269-5311

THE UNITED KINGDOM

Yamaha Music U.K. Ltd.

Sherbourne Drive, Tilbrook, Milton Keynes,

MK7 8BL, England

Tel: 01908-366700

IRELAND

Danfay Ltd.

61D, Sallynoggin Road, Dun Laoghaire, Co. Dublin

Tel: 01-2859177

GERMANY

Yamaha Music Central Europe GmbH

Siemensstraße 22-34, 25462 Rellingen, Germany

Tel: 04101-3030

SWITZERLAND/LIECHTENSTEIN

Yamaha Music Central Europe GmbH,

Branch Switzerland

Seefeldstrasse 94, 8008 Zürich, Switzerland

Tel: 01-383 3990

AUSTRIA

Yamaha Music Central Europe GmbH,

Branch Austria

Schleiergasse 20, A-1100 Wien, Austria

Tel: 01-60203900

CZECH REPUBLIC/SLOVAKIA/

HUNGARY/SLOVENIA

Yamaha Music Central Europe GmbH,

Branch Austria, CEE Department

Schleiergasse 20, A-1100 Wien, Austria

Tel: 01-602039025

POLAND

Yamaha Music Central Europe GmbH

Sp.z. o.o. Oddzial w Polsce

ul. 17 Stycznia 56, PL-02-146 Warszawa, Poland

Tel: 022-868-07-57

THE NETHERLANDS/

BELGIUM/LUXEMBOURG

Yamaha Music Central Europe GmbH,

Branch Benelux

Clarissenhof 5-b, 4133 AB Vianen, The Netherlands

Tel: 0347-358 040

FRANCE

Yamaha Musique France

BP 70-77312 Marne-la-Vallée Cedex 2, France

Tel: 01-64-61-4000

ITALY

Yamaha Musica Italia S.P.A.

Viale Italia 88, 20020 Lainate (Milano), Italy

Tel: 02-935-771

SPAIN/PORTUGAL

Yamaha Música Ibérica, S.A.

Ctra. de la Coruna km. 17, 200, 28230

Las Rozas (Madrid), Spain

Tel: 91-639-8888

GREECE

Philippos Nakas S.A. The Music House

147 Skiathou Street, 112-55 Athens, Greece

Tel: 01-228 2160

SWEDEN

Yamaha Scandinavia AB

J. A. Wettergrens Gata 1, Box 30053

S-400 43 Göteborg, Sweden

Tel: 031 89 34 00

DENMARK

YS Copenhagen Liaison Ofﬁce

Generatorvej 6A, DK-2730 Herlev, Denmark

Tel: 44 92 49 00

FINLAND

F-Musiikki Oy

Kluuvikatu 6, P.O. Box 260,

SF-00101 Helsinki, Finland

Tel: 09 618511

NORWAY

Norsk ﬁlial av Yamaha Scandinavia AB

Grini Næringspark 1, N-1345 Østerås, Norway

Tel: 67 16 77 70

ICELAND

Skifan HF

Skeifan 17 P.O. Box 8120, IS-128 Reykjavik, Ice-

land

Tel: 525 5000

RUSSIA

Yamaha Music (Russia)

Ofﬁce 4015, entrance 2, 21/5 Kuznetskii

Most street, Moscow, 107996, Russia

Tel: 495 626 0660

OTHER EUROPEAN COUNTRIES

Yamaha Music Central Europe GmbH

Siemensstraße 22-34, 25462 Rellingen, Germany

Tel: +49-4101-3030

Yamaha Corporation,

Asia-Paciﬁc Music Marketing Group

Nakazawa-cho 10-1, Naka-ku, Hamamatsu,

Japan 430-8650

Tel: +81-53-460-2312

TURKEY/CYPRUS

Yamaha Music Central Europe GmbH

Siemensstraße 22-34, 25462 Rellingen, Germany

Tel: 04101-3030

OTHER COUNTRIES

Yamaha Music Gulf FZE

LOB 16-513, P.O.Box 17328, Jubel Ali,

Dubai, United Arab Emirates

Tel: +971-4-881-5868

THE PEOPLE’S REPUBLIC OF CHINA

Yamaha Music & Electronics (China) Co.,Ltd.

25/F., United Plaza, 1468 Nanjing Road (West),

Jingan, Shanghai, China

Tel: 021-6247-2211

HONG KONG

Tom Lee Music Co., Ltd.

11/F., Silvercord Tower 1, 30 Canton Road,

Tsimshatsui, Kowloon, Hong Kong

Tel: 2737-7688

INDONESIA

PT. Yamaha Music Indonesia (Distributor)

PT. Nusantik

Gedung Yamaha Music Center, Jalan Jend. Gatot

Subroto Kav. 4, Jakarta 12930, Indonesia

Tel: 21-520-2577

KOREA

Yamaha Music Korea Ltd.

8F, 9F, Dongsung Bldg. 158-9 Samsung-Dong,

Kangnam-Gu, Seoul, Korea

Tel: 080-004-0022

MALAYSIA

Yamaha Music Malaysia, Sdn., Bhd.

Lot 8, Jalan Perbandaran, 47301 Kelana Jaya,

Petaling Jaya, Selangor, Malaysia

Tel: 3-78030900

PHILIPPINES

Yupangco Music Corporation

339 Gil J. Puyat Avenue, P.O. Box 885 MCPO,

Makati, Metro Manila, Philippines

Tel: 819-7551

SINGAPORE

Yamaha Music Asia Pte., Ltd.

#03-11 A-Z Building

140 Paya Lebor Road, Singapore 409015

Tel: 747-4374

TAIWAN

Yamaha KHS Music Co., Ltd.

3F, #6, Sec.2, Nan Jing E. Rd. Taipei.

Taiwan 104, R.O.C.

Tel: 02-2511-8688

THAILAND

Siam Music Yamaha Co., Ltd.

891/1 Siam Motors Building, 15-16 ﬂoor

Rama 1 road, Wangmai, Pathumwan

Bangkok 10330, Thailand

Tel: 02-215-2626

OTHER ASIAN COUNTRIES

Yamaha Corporation,

Asia-Paciﬁc Music Marketing Group

Nakazawa-cho 10-1, Naka-ku, Hamamatsu,

Japan 430-8650

Tel: +81-53-460-2317

AUSTRALIA

Yamaha Music Australia Pty. Ltd.

Level 1, 99 Queensbridge Street, Southbank,

Victoria 3006, Australia

Tel: 3-9693-5111

NEW ZEALAND

Music Houses of N.Z. Ltd.

146/148 Captain Springs Road, Te Papapa,

Auckland, New Zealand

Tel: 9-634-0099

COUNTRIES AND TRUST

TERRITORIES IN PACIFIC OCEAN

Yamaha Corporation,

Asia-Paciﬁc Music Marketing Group

Nakazawa-cho 10-1, Naka-ku, Hamamatsu,

Japan 430-8650

Tel: +81-53-460-2312

NORTH AMERICA

CENTRAL & SOUTH AMERICA

EUROPE

AFRICA

MIDDLE EAST

ASIA

OCEANIA

HEAD OFFICE Yamaha Corporation, Pro Audio & Digital Musical Instrument Division

Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650

Tel: +81-53-460-3273

EKB43

149

U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation

WM81140 804YCPA*.*-01A1 Printed in Indonesia

Clavinova Web site

http://music.yamaha.com/homekeyboard

Yamaha Manual Library

http://www.yamaha.co.jp/manual/

Yamaha Clavinova CLP-320 de handleiding

Merk: Yamaha

Model: Clavinova CLP-320

Categorie: Aanvullende muziekapparatuur

Type: de handleiding

Deze handleiding is ook geschikt voor

Download PDF

rapport

in andere talen

English: Yamaha Clavinova CLP-320 Owner's manual
italiano: Yamaha Clavinova CLP-320 Manuale del proprietario
русский: Yamaha Clavinova CLP-320 Инструкция по применению
français: Yamaha Clavinova CLP-320 Le manuel du propriétaire
español: Yamaha Clavinova CLP-320 El manual del propietario
Deutsch: Yamaha Clavinova CLP-320 Bedienungsanleitung
português: Yamaha Clavinova CLP-320 Manual do proprietário
dansk: Yamaha Clavinova CLP-320 Brugervejledning
suomi: Yamaha Clavinova CLP-320 Omistajan opas
čeština: Yamaha Clavinova CLP-320 Návod k obsluze
svenska: Yamaha Clavinova CLP-320 Bruksanvisning
Türkçe: Yamaha Clavinova CLP-320 El kitabı
polski: Yamaha Clavinova CLP-320 Instrukcja obsługi
română: Yamaha Clavinova CLP-320 Manualul proprietarului

Andere documenten

iON DISCOVER KEYBOARD USB de handleiding

Yamaha Clavinova CLP-320 de handleiding

Deze handleiding is ook geschikt voor

Yamaha Clavinova CLP-320 de handleiding

in andere talen

Gerelateerde artikelen

Andere documenten