Documenttranscriptie

1 Preparations Accessories Check that the following accessories are supplied with this product. AV Receiver Easy Setup Guide English for Europe, Asia, Africa, Oceania and Latin America ■ Remote control ■ Batteries (AAA, R03, UM-4) (x 2) Insert into the remote control in the correct polarity (+/-). ■ YPAO microphone ■ VIDEO AUX input cover ■ AM antenna ■ FM antenna *The figure of the supplied FM antenna differs depending on regions. ■ CD-ROM (Owner’s Manual) ■ Safety Brochure ■ Easy Setup Guide (this document) Cables necessary for connections Th is do c u me n t e x p l ai n s h ow to s e t up a 5 . 1 - o r 7 . 1 - c h an n e l s ys t e m a n d p l a y b a c k s u r ro u n d s o un d of a B D /DV D o n thi s un it. For m o re i n fo r m a t i o n , re fe r t o “O w n e r ’s M a n u a l ” o n t h e s u p p l i e d CD - R OM . A P DF for ma t o f t h i s g u i d e a nd “O w n e r ’s M an u a l ” c a n b e d ow nl o a d e d from th e following website. http://dow nload.yamaha.com/ You need to separately prepare the following cables to build the system based on this document. ■ Speaker cables (depending on the number of speakers) ■ HDMI cable (x 2) ■ Audio pin cable (x 1) ■ Digital optical cable (x 1) (unnecessary if your TV supports ARC) 2 Placing the speakers Set up the speakers in the room by using the following diagram as a reference. For information on other speaker systems, refer to “Owner’s Manual”. 5.1-channel system 7.1-channel system 60° 60° 80° 80° 30 cm or more 60° 60° 80° 80° Front speaker (L) Front speaker (R) Center speaker Surround speaker (L) Surround speaker (R) Surround back speaker (L) Surround back speaker (R) Subwoofer 2 En 3 Connecting the speakers/subwoofer • This unit is configured for 8-ohm speakers at the factory. When connecting 6-ohm speakers, set the speaker impedance of this unit to “6 Ω MIN”. For details, see “Setting the speaker impedance” (p.16) in “Owner’s Manual”. the front speakers ( 1 Connect to the FRONT ( / ) terminals. / ) the center speaker ( 2 Connect CENTER terminal. ) to the • Use a subwoofer equipped with built-in amplifier. • Remove the power cable of this unit from an AC wall outlet and turn off the subwoofer before connecting the speakers. • Be careful that the core of the speaker cable does not touch anything or come into contact with the metal areas of this unit. This may damage this unit or the speakers. If the speaker cables short circuit, “CHECK SP WIRES” will appear on the front display when this unit is turned on. This unit (rear) This unit (rear) SPEAKERS R FRONT L CENTER R SURROUND L SPEAKERS R SURROUND BACK/BI–AMP R L FRONT L CENTER R SURROUND L SURROUND BACK/BI–AMP R L SINGLE SINGLE R L R EXTRA SP ZONE 2/ PRESENCE L EXTRA SP ZONE 2/ PRESENCE Connecting speaker cables Speaker cables have two wires. One is for connecting the negative (-) terminal of the unit and the speaker, and the other is for the positive (+) terminal. If the wires are colored to prevent confusion, connect the black wire to the negative and the other wire to the positive. SUBWOOFER SUBWOOFER a Remove approximately c 10 mm of insulation from + (red) b the ends of the speaker cable, and twist the bare a d wires of the cable – (black) together firmly. b Loosen the speaker terminal. c Insert the bare wires of the cable into the gap on the side (upper right or bottom left) of the terminal. d Tighten the terminal. FR ON T Using a banana plug (China, Australia and General models only) a Tighten the speaker terminal. b Insert a banana plug into the end of the terminal. Banana plug a FR ON T b En 3 the surround speakers ( 3 Connect ) to the SURROUND ( / ) / the subwoofer ( 4 Connect SUBWOOFER jack. ) to the Connect the surround back speakers ( ) to the SURROUND BACK ( / ) terminals. terminals. This unit (rear) This unit (rear) FRONT L CENTER R SURROUND L R SURROUND BACK/BI–AMP R FRONT L CENTER R SURROUND L SPEAKERS R SURROUND BACK/BI–AMP R L SINGLE L CENTER R SURROUND L SURROUND BACK/BI–AMP L L R EXTRA SP ZONE 2/ PRESENCE SUBWOOFER SUBWOOFER Use an audio pin cable to connect the subwoofer ( ). En L SINGLE R EXTRA SP ZONE 2/ PRESENCE 4 FRONT R L SINGLE R / This unit (rear) SPEAKERS SPEAKERS R For 7.1-channel system Audio pin cable L EXTRA SP ZONE 2/ PRESENCE SUBWOOFER 4 Connecting the external devices Before connecting the power cable (General model only) Make sure you set the switch position of VOLTAGE SELECTOR according to your local voltage. Voltages are AC 110-120/220-240 V, 50/60 Hz. TV Audio out (optical) HDMI in OPTICAL HDMI out HDMI HDMI HDMI HDMI O b c a Connect the BD/DVD player and this unit with an HDMI cable. If the BD/DVD player is currently connected to the TV directly with an HDMI cable, disconnect the cable from the TV and connect it to this unit. b Connect the TV and this unit with another HDMI cable. a HDMI HDMI HDMI OUT (BD/DVD) VOLTAGE SELECTOR HDMI 1 220V-240V HDMI OUT jack 1 Connect the external devices to this unit. BD/DVD player VOLTAGE SELECTOR (General model only) 110V-120V HDMI1 jack ARC d MAINS DOCK NETWORK HDMI 1 HDMI OUT HDMI 2 (BD/DVD) HDMI 3 HDMI 4 HDMI 5 ARC PHONO COMPONENT VIDEO AM d Connect the power cable to an AC wall outlet. SPEAKERS ANTENNA L To an AC wall outlet c Connect the TV and this unit with a digital optical cable. This connection is required to play back TV audio on this unit. If your TV supports ARC (Audio Return Channel), this connection is unnecessary. R COMPONENT VIDEO FRONT L CENTER R SURROUND L SURROUND BACK/BI–AMP R FM L REMOTE PR IN PR R GND SINGLE S VIDEO PB VIDEO R OUT 75Ω PB L EXTRA SP ZONE 2/ PRESENCE VIDEO +12V 0.1A MAX. Y Y MONITOR OUT 2 Turn on this unit, TV and BD/DVD player. the remote control of the TV, switch 3 With the TV input to display the video from this TRIGGER OUT L R O OPTICAL OPTICAL (TV) AV4 (OPTICAL) jack AV 1 AV 4 COAXIAL AV 2 COAXIAL OPTICAL (CD) (TV) AV 3 AV 4 AV 5 AV 6 AV OUT AUDIO 1 AUDIO OUT AUDIO 2 ZONE 2 OUT SUBWOOFER This unit (rear) (U.K. and Europe models) unit. The connections are complete. Move to the next page to optimize the speaker settings. NATURAL SOUND AV RECEIVER RX-V671 MAIN ZONE YPAO MIC Turn on this unit • For information on how to connect radio antennas or other external devices, see “SETUP” in “Owner’s Manual”. PURE DIRECT ZONE2 ZONE CONTROL INFO MEMORY PRESET FM AM TUNING VOLUME SCENE BD DVD PHONES SILENT CINEMA USB INPUT TONE CONTROL TV CD PROGRAM RADIO VIDEO AUX STRAIGHT iPod/iPhone HDMI IN VIDEO L AUDIO R This unit (front) En 5 5 Optimizing the speaker settings automatically (YPAO) By using the Yamaha Parametric room Acoustic Optimizer (YPAO) function, this unit automatically detects speaker connections and distances from the listening position, and optimizes the speaker settings such as volume balance and acoustic parameters to suit your room. • During the measuring process, the test tones are output at high volume. Take care that the test tone does not frighten small children. Also, refrain from using this function at night when it may be a nuisance to others. MAIN ZONE 2 CODE SET HDMI • During the measuring process, keep the room as quiet as possible. 1 2 3 4 • Do not connect headphones. 5 • If your subwoofer supports the auto-standby function, disable it. 1 2 3 4 5 6 AUDIO DOCK TUNER PHONO NET USB FM AM PRESET TUNING • YPAO measurement is not performed correctly when any obstacles are in the room. • During the measuring process (about 3 minutes), keep stuff in the corners or remove it from the room. V-AUX AV INFO MEMORY MOVIE MUSIC • To cancel the operation, disconnect the YPAO microphone before starting the measurement. start the measurement, use the cursor 2 To keys to select “Measure” and press SUR. DECODE STRAIGHT This unit (front) SLEEP ENHANCER PURE DIRECT ENTER. SCENE BD DVD Turned on the subwoofer and set the volume to half. If the cross-over frequency is adjustable, set it to maximum. TV CD CROSSOVER/ HIGH CUT RADIO OPTION ON SCREEN VOLUME ENTER VOLUME The following screen appears on the TV. SOURCE RECEIVER • During the measuring process, you cannot adjust the volume. Preparing for YPAO the YPAO microphone to the 1 Connect YPAO MIC jack on the front panel. RETURN DISPLAY POP-UP MENU TOP MENU Cursor keys ENTER RETURN The measurement will start in 10 seconds. The following screen appears on the TV when the measurement finishes. MUTE MODE MIN MAX MIN MAX YPAO microphone Listening position 1 2 3 5 6 7 9 0 10 4 8 ENT TV INPUT TV VOL TV CH MUTE Ear height Place the YPAO microphone at ear height in your listening position. We recommend using a tripod to adjust the height. You can use the tripod screws to fix the microphone in place. 6 En • If any error message (such as E-1) or warning message (such as W-2) appears, see “Error messages” (p.38) or “Warning messages” (p.39) in “Owner’s Manual”. • If the warning message “W-1:Out of Phase” appears, see “If ‘W-1:Out of Phase’ appears” (next page). the cursor keys to select 3 Use “Save/Cancel” and press ENTER. If “W-1: Out of Phase” appears Follow the procedure below to check the speaker connections. Depending on the type of speakers or room environment, this message may appear even if the speakers are connected correctly. the cursor keys to select “SAVE” and 4 Use press ENTER. a Use the cursor keys to select “Result” and press ENTER. b Use the cursor keys to select “Wiring”. c Check the cable connections (+/-) of the speaker indicated with “Reverse”. If the speaker is connected correctly: You can save the current settings. Press RETURN and proceed to step 3. the YPAO microphone from 5 Disconnect this unit. If the speaker is connected incorrectly: Turn off this unit, reconnect the speaker cable, and then try YPAO measurement again. Now optimization of the speaker settings is complete. • Since the YPAO microphone is sensitive to heat, do not place the microphone in any place where it will be subjected to direct sunlight or high temperatures (top of an AV equipment, etc). En 7 6 Playing back a BD/DVD Now let’s play back a BD/DVD. We recommend playing back multichannel audio (5.1channel or more) to feel surround sound produced by this unit. Much more features! 1 Press HDMI1 to select “HDMI1” as the input source. This unit has various other functions. Please refer to “Owner’s Manual” on the supplied CD-ROM and utilize this unit effectively. VOL. MAIN ZONE 2 HDMI1 CODE SET SOURCE RECEIVER HDMI 1 2 3 5 4 HDMI1 V-AUX AV 1 2 3 4 5 6 AUDIO DOCK TUNER PHONO NET USB FM AM PRESET TUNING INFO MEMORY MOVIE MUSIC SUR. DECODE STRAIGHT SLEEP L SL SW C R SR 2 Start playback on the BD/DVD player. STRAIGHT repeatedly to select 3 Press “STRAIGHT”. VOL. STRAIGHT L SL SW C R SR STRAIGHT Connect audio devices (CD player, etc.), game console, camcorder, and many others. Selecting the sound mode (p.42) Select the desired sound program (CINEMA DSP) or surround decoder suitable for movies, music, games, sports programs and other uses. ENHANCER PURE DIRECT BD DVD • When “STRAIGHT” (straight decode) is enabled, each speaker produces each channel audio signal directly (without sound field processing). If you play back 5.1-channel audio on the 7.1-channel system, no sounds will be heard from the surround back speakers. RADIO ON SCREEN VOLUME POP-UP MENU VOLUME 4 Press VOLUME to adjust the volume. 1 2 3 4 5 6 7 8 9 0 10 ENT L SL SW C R SR Now the basic setup procedure is complete. If you cannot have surround sound INPUT TV VOL TV CH By using a USB cable supplied with iPod, an optional Yamaha iPod dock or an optional Yamaha iPod wireless system, you can enjoy iPod music on this unit. VOL. Volume -30.0dB TV Playing back from iPod (p.52) MUTE MODE MUTE Connecting other playback devices (p.26) Only the front speakers work on multichannel audio Check the digital audio output setting on the BD/DVD player. It may be set to output 2-channel audio (PCM, etc.) only. No sound is heard from a specific speaker See “Troubleshooting” (p.108) in “Owner’s Manual”. ■ Listening to FM/AM radio (p.47) ■ Playing back music stored on a USB storage device (p.59) ■ Playing back the network contents (p.62 to p.65) ■ Selecting the input source and favorite settings at once (p.41) For more information, see “What you can do with this unit” (p.6). © 2011 Yamaha Corporation YD458C0/ESEN3